1 files changed, 0 insertions, 131 deletions
diff --git a/uc_str912/openocd/str912.cfg b/uc_str912/openocd/str912.cfg
deleted file mode 100644
index 108ae9c..0000000
--- a/uc_str912/openocd/str912.cfg
+++ /dev/null
@@ -1,131 +0,0 @@
-# script for str9
-
-if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
-} else {
-   set  _CHIPNAME str912
-}
-
-if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
-} else {
-   set  _ENDIAN little
-}
-
-# jtag speed. We need to stick to 16kHz until we've finished reset.
-jtag_rclk 16
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-#reset_config trst_only
-
-if { [info exists FLASHTAPID ] } {
-   set _FLASHTAPID $FLASHTAPID
-} else {
-   set _FLASHTAPID 0x04570041
-}
-jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
-
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-   set _CPUTAPID 0x25966041
-}
-jtag newtap $_CHIPNAME cpu   -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-
-if { [info exists BSTAPID ] } {
-   set _BSTAPID $BSTAPID
-} else {
-   set _BSTAPID 0x1457f041
-}
-jtag newtap $_CHIPNAME bs    -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
-
-$_TARGETNAME configure -event reset-start { jtag_rclk 16 }
-
-$_TARGETNAME configure -event reset-init {
-	# We can increase speed now that we know the target is halted.
-	jtag_rclk 2000
-
-	# -- Enable 96K RAM
-	# PFQBC enabled / DTCM & AHB wait-states disabled
-	mww 0x5C002034 0x0191
-
-    flash banks
-    flash probe 0
-
-    #str9x flash_config <bank> <bbsize> <nbsize> <bbstart> <nbstart>
-    str9x flash_config    0         4       2        0x0     0x80000
-
-    #nbsize register = 0 : means  8kBytes (written in the STR9 flash programming manual)
-    #nbsize register = 2 : means 32kBytes (written in the STR9 flash programming manual)
-    #bbsize register = 4 : means 512kBytes (written in the STR9 flash programming manual)
-
-
-	flash protect 0 0 7 off
-    flash protect_check 0
-#   flash info 0
-
-	flash protect 1 0 3 off
-    flash protect_check 1
-#   flash info 1
-
-    flash auto_erase on
-}
-
-#$_TARGETNAME configure -work-area-phys 0x04000000 -work-area-size 16384 -work-area-backup 0
-$_TARGETNAME configure -work-area-phys 0x04000000 -work-area-size 0x18000 -work-area-backup 0
-
-#flash bank str9x <base> <size> 0 0 <target#> <variant>
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME str9x 0x00000000 0x00080000 0 0 $_TARGETNAME
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME str9x 0x00080000 0x00008000 0 0 $_TARGETNAME
-
-
-
-
-$_TARGETNAME configure -event debug-halted {
-	puts "Running debug halted script for EBx00 Board"
-}
-
-
-$_TARGETNAME configure -event gdb-attach {
-	puts "Running gdb-attach script for EBx00 Board"
-}
-
-
-$_TARGETNAME configure -event gdb-detach {
-	puts "Running gdb-detach script for EBx00 Board"
-}
-
-
-$_TARGETNAME configure -event gdb-flash-erase-start {
-	puts "Running gdb-flash-erase-start script for EBx00 Board"
-}
-
-
-$_TARGETNAME configure -event gdb-flash-erase-end {
-	puts "Running gdb-flash-erase-end script for EBx00 Board"
-}
-
-
-$_TARGETNAME configure -event gdb-start {
-	puts "Running gdb_start script for EBx00 Board"
-}
-
-
-
-$_TARGETNAME configure -event gdb-end {
-	puts "Running gdb_halted script for EBx00 Board"
-}
-
-
-# For more information about the configuration files, take a look at:
-# openocd.texi