1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
|
/*
* This file is part of the coreboot project.
*
* Copyright (C) 2011 Advanced Micro Devices, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <arch/io.h>
#include <arch/romcc_io.h>
static void enable_rom(void)
{
u16 word;
u32 dword;
device_t dev;
dev = PCI_DEV(0, 0x14, 0x03);
/* SB800 LPC Bridge 0:20:3:44h.
* BIT6: Port Enable for serial port 0x3f8-0x3ff
* BIT29: Port Enable for KBC port 0x60 and 0x64
* BIT30: Port Enable for ACPI Micro-Controller port 0x66 and 0x62
*/
dword = pci_io_read_config32(dev, 0x44);
//dword |= (1<<6) | (1<<29) | (1<<30) ;
/* Turn on all of LPC IO Port decode enable */
dword = 0xffffffff;
pci_io_write_config32(dev, 0x44, dword);
/* SB800 LPC Bridge 0:20:3:48h.
* BIT0: Port Enable for SuperIO 0x2E-0x2F
* BIT1: Port Enable for SuperIO 0x4E-0x4F
* BIT4: Port Enable for LPC ROM Address Arrage2 (0x68-0x6C)
* BIT6: Port Enable for RTC IO 0x70-0x73
* BIT21: Port Enable for Port 0x80
*/
dword = pci_io_read_config32(dev, 0x48);
dword |= (1 << 0) | (1 << 1) | (1 << 4) | (1 << 6) | (1 << 21);
pci_io_write_config32(dev, 0x48, dword);
/* Enable rom access */
word = pci_io_read_config16(dev, 0x6c);
word = 0x10000 - (CONFIG_COREBOOT_ROMSIZE_KB >> 6);
pci_io_write_config16(dev, 0x6c, word);
}
static void enable_prefetch(void)
{
u32 dword;
device_t dev = PCI_DEV(0, 0x14, 0x03);
/* Enable PrefetchEnSPIFromHost */
dword = pci_io_read_config32(dev, 0xb8);
pci_io_write_config32(dev, 0xb8, dword | (1 << 24));
}
static void enable_spi_fast_mode(void)
{
u8 byte;
u32 dword;
device_t dev = PCI_DEV(0, 0x14, 0x03);
// set temp MMIO base
volatile u32 *spi_base = (void *)0xa0000000;
u32 save = pci_io_read_config32(dev, 0xa0);
pci_io_write_config32(dev, 0xa0, (u32) spi_base | 2);
// early enable of SPI 33 MHz fast mode read
byte = spi_base[3];
spi_base[3] = (byte & ~(3 << 14)) | (1 << 14);
spi_base[0] = spi_base[0] | (1 << 18); // fast read enable
pci_io_write_config32(dev, 0xa0, save);
}
static void enable_clocks(void)
{
u8 reg8;
u32 reg32;
volatile u32 *acpi_mmio = (void *) (0xFED80000 + 0xE00 + 0x40);
// Program AcpiMmioEn to enable MMIO access to MiscCntrl register
outb(0x24, 0xCD6);
reg8 = inb(0xCD7);
reg8 |= 1;
reg8 &= ~(1 << 1);
outb(reg8, 0xCD7);
// Program SB800 MiscClkCntrl register to configure clock output on the
// 14M_25M_48M_OSC ball usually used for the Super-I/O.
// Almost all SIOs need 48 MHz, only the SMSC SCH311x wants 14 MHz,
// which is the SB800's power up default. We could switch back to 14
// in the mainboard's romstage.c, but then the clock frequency would
// change twice.
reg32 = *acpi_mmio;
reg32 &= ~((1 << 2) | (3 << 0)); // enable, 14 MHz (power up default)
#if !CONFIG_SUPERIO_WANTS_14MHZ_CLOCK
reg32 |= 2 << 0; // Device_CLK1_sel = 48 MHz
#endif
*acpi_mmio = reg32;
}
static void bootblock_southbridge_init(void)
{
/* Setup the rom access for 2M */
enable_rom();
enable_prefetch();
enable_spi_fast_mode();
enable_clocks();
}
|
