1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
|
Decoder firmware API description
================================
Note: this API is part of the decoder firmware, so it's cx23415 only.
-------------------------------------------------------------------------------
Name CX2341X_DEC_PING_FW
Enum 0/0x00
Description
This API call does nothing. It may be used to check if the firmware
is responding.
-------------------------------------------------------------------------------
Name CX2341X_DEC_START_PLAYBACK
Enum 1/0x01
Description
Begin or resume playback.
Param[0]
0 based frame number in GOP to begin playback from.
Param[1]
Specifies the number of muted audio frames to play before normal
audio resumes. (This is not implemented in the firmware, leave at 0)
-------------------------------------------------------------------------------
Name CX2341X_DEC_STOP_PLAYBACK
Enum 2/0x02
Description
Ends playback and clears all decoder buffers. If PTS is not zero,
playback stops at specified PTS.
Param[0]
Display 0=last frame, 1=black
Note: this takes effect immediately, so if you want to wait for a PTS,
then use '0', otherwise the screen goes to black at once.
You can call this later (even if there is no playback) with a 1 value
to set the screen to black.
Param[1]
PTS low
Param[2]
PTS high
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_PLAYBACK_SPEED
Enum 3/0x03
Description
Playback stream at speed other than normal. There are two modes of
operation:
Smooth: host transfers entire stream and firmware drops unused
frames.
Coarse: host drops frames based on indexing as required to achieve
desired speed.
Param[0]
Bitmap:
0:7 0 normal
1 fast only "1.5 times"
n nX fast, 1/nX slow
30 Framedrop:
'0' during 1.5 times play, every other B frame is dropped
'1' during 1.5 times play, stream is unchanged (bitrate
must not exceed 8mbps)
31 Speed:
'0' slow
'1' fast
Note: n is limited to 2. Anything higher does not result in
faster playback. Instead the host should start dropping frames.
Param[1]
Direction: 0=forward, 1=reverse
Note: to make reverse playback work you have to write full GOPs in
reverse order.
Param[2]
Picture mask:
1=I frames
3=I, P frames
7=I, P, B frames
Param[3]
B frames per GOP (for reverse play only)
Note: for reverse playback the Picture Mask should be set to I or I, P.
Adding B frames to the mask will result in corrupt video. This field
has to be set to the correct value in order to keep the timing correct.
Param[4]
Mute audio: 0=disable, 1=enable
Param[5]
Display 0=frame, 1=field
Param[6]
Specifies the number of muted audio frames to play before normal audio
resumes. (Not implemented in the firmware, leave at 0)
-------------------------------------------------------------------------------
Name CX2341X_DEC_STEP_VIDEO
Enum 5/0x05
Description
Each call to this API steps the playback to the next unit defined below
in the current playback direction.
Param[0]
0=frame, 1=top field, 2=bottom field
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_DMA_BLOCK_SIZE
Enum 8/0x08
Description
Set DMA transfer block size. Counterpart to API 0xC9
Param[0]
DMA transfer block size in bytes. A different size may be specified
when issuing the DMA transfer command.
-------------------------------------------------------------------------------
Name CX2341X_DEC_GET_XFER_INFO
Enum 9/0x09
Description
This API call may be used to detect an end of stream condition.
Result[0]
Stream type
Result[1]
Address offset
Result[2]
Maximum bytes to transfer
Result[3]
Buffer fullness
-------------------------------------------------------------------------------
Name CX2341X_DEC_GET_DMA_STATUS
Enum 10/0x0A
Description
Status of the last DMA transfer
Result[0]
Bit 1 set means transfer complete
Bit 2 set means DMA error
Bit 3 set means linked list error
Result[1]
DMA type: 0=MPEG, 1=OSD, 2=YUV
-------------------------------------------------------------------------------
Name CX2341X_DEC_SCHED_DMA_FROM_HOST
Enum 11/0x0B
Description
Setup DMA from host operation. Counterpart to API 0xCC
Param[0]
Memory address of link list
Param[1]
Total # of bytes to transfer
Param[2]
DMA type (0=MPEG, 1=OSD, 2=YUV)
-------------------------------------------------------------------------------
Name CX2341X_DEC_PAUSE_PLAYBACK
Enum 13/0x0D
Description
Freeze playback immediately. In this mode, when internal buffers are
full, no more data will be accepted and data request IRQs will be
masked.
Param[0]
Display: 0=last frame, 1=black
-------------------------------------------------------------------------------
Name CX2341X_DEC_HALT_FW
Enum 14/0x0E
Description
The firmware is halted and no further API calls are serviced until
the firmware is uploaded again.
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_STANDARD
Enum 16/0x10
Description
Selects display standard
Param[0]
0=NTSC, 1=PAL
-------------------------------------------------------------------------------
Name CX2341X_DEC_GET_VERSION
Enum 17/0x11
Description
Returns decoder firmware version information
Result[0]
Version bitmask:
Bits 0:15 build
Bits 16:23 minor
Bits 24:31 major
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_STREAM_INPUT
Enum 20/0x14
Description
Select decoder stream input port
Param[0]
0=memory (default), 1=streaming
-------------------------------------------------------------------------------
Name CX2341X_DEC_GET_TIMING_INFO
Enum 21/0x15
Description
Returns timing information from start of playback
Result[0]
Frame count by decode order
Result[1]
Video PTS bits 0:31 by display order
Result[2]
Video PTS bit 32 by display order
Result[3]
SCR bits 0:31 by display order
Result[4]
SCR bit 32 by display order
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_AUDIO_MODE
Enum 22/0x16
Description
Select audio mode
Param[0]
Dual mono mode action
0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
Param[1]
Stereo mode action:
0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_EVENT_NOTIFICATION
Enum 23/0x17
Description
Setup firmware to notify the host about a particular event.
Counterpart to API 0xD5
Param[0]
Event: 0=Audio mode change between mono, (joint) stereo and dual channel.
Event: 3=Decoder started
Event: 4=Unknown: goes off 10-15 times per second while decoding.
Event: 5=Some sync event: goes off once per frame.
Param[1]
Notification 0=disabled, 1=enabled
Param[2]
Interrupt bit
Param[3]
Mailbox slot, -1 if no mailbox required.
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_DISPLAY_BUFFERS
Enum 24/0x18
Description
Number of display buffers. To decode all frames in reverse playback you
must use nine buffers.
Param[0]
0=six buffers, 1=nine buffers
-------------------------------------------------------------------------------
Name CX2341X_DEC_EXTRACT_VBI
Enum 25/0x19
Description
Extracts VBI data
Param[0]
0=extract from extension & user data, 1=extract from private packets
Result[0]
VBI table location
Result[1]
VBI table size
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_DECODER_SOURCE
Enum 26/0x1A
Description
Selects decoder source. Ensure that the parameters passed to this
API match the encoder settings.
Param[0]
Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host
Param[1]
YUV picture width
Param[2]
YUV picture height
Param[3]
Bitmap: see Param[0] of API 0xBD
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_PREBUFFERING
Enum 30/0x1E
Description
Decoder prebuffering, when enabled up to 128KB are buffered for
streams <8mpbs or 640KB for streams >8mbps
Param[0]
0=off, 1=on
|
