diff options
Diffstat (limited to 'src/roms/u-boot/drivers/usb/musb/musb_core.c')
| -rw-r--r-- | src/roms/u-boot/drivers/usb/musb/musb_core.c | 155 |
1 files changed, 155 insertions, 0 deletions
diff --git a/src/roms/u-boot/drivers/usb/musb/musb_core.c b/src/roms/u-boot/drivers/usb/musb/musb_core.c new file mode 100644 index 0000000..786909f --- /dev/null +++ b/src/roms/u-boot/drivers/usb/musb/musb_core.c @@ -0,0 +1,155 @@ +/* + * Mentor USB OTG Core functionality common for both Host and Device + * functionality. + * + * Copyright (c) 2008 Texas Instruments + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Author: Thomas Abraham t-abraham@ti.com, Texas Instruments + */ + +#include <common.h> + +#include "musb_core.h" +struct musb_regs *musbr; + +/* + * program the mentor core to start (enable interrupts, dma, etc.) + */ +void musb_start(void) +{ +#if defined(CONFIG_MUSB_HCD) + u8 devctl; + u8 busctl; +#endif + + /* disable all interrupts */ + writew(0, &musbr->intrtxe); + writew(0, &musbr->intrrxe); + writeb(0, &musbr->intrusbe); + writeb(0, &musbr->testmode); + + /* put into basic highspeed mode and start session */ + writeb(MUSB_POWER_HSENAB, &musbr->power); +#if defined(CONFIG_MUSB_HCD) + /* Program PHY to use EXT VBUS if required */ + if (musb_cfg.extvbus == 1) { + busctl = musb_read_ulpi_buscontrol(musbr); + musb_write_ulpi_buscontrol(musbr, busctl | ULPI_USE_EXTVBUS); + } + + devctl = readb(&musbr->devctl); + writeb(devctl | MUSB_DEVCTL_SESSION, &musbr->devctl); +#endif +} + +#ifdef MUSB_NO_DYNAMIC_FIFO +# define config_fifo(dir, idx, addr) +#else +# define config_fifo(dir, idx, addr) \ + do { \ + writeb(idx, &musbr->dir##fifosz); \ + writew(fifoaddr >> 3, &musbr->dir##fifoadd); \ + } while (0) +#endif + +/* + * This function configures the endpoint configuration. The musb hcd or musb + * device implementation can use this function to configure the endpoints + * and set the FIFO sizes. Note: The summation of FIFO sizes of all endpoints + * should not be more than the available FIFO size. + * + * epinfo - Pointer to EP configuration table + * cnt - Number of entries in the EP conf table. + */ +void musb_configure_ep(const struct musb_epinfo *epinfo, u8 cnt) +{ + u16 csr; + u16 fifoaddr = 64; /* First 64 bytes of FIFO reserved for EP0 */ + u32 fifosize; + u8 idx; + + while (cnt--) { + /* prepare fifosize to write to register */ + fifosize = epinfo->epsize >> 3; + idx = ffs(fifosize) - 1; + + writeb(epinfo->epnum, &musbr->index); + if (epinfo->epdir) { + /* Configure fifo size and fifo base address */ + config_fifo(tx, idx, fifoaddr); + + csr = readw(&musbr->txcsr); +#if defined(CONFIG_MUSB_HCD) + /* clear the data toggle bit */ + writew(csr | MUSB_TXCSR_CLRDATATOG, &musbr->txcsr); +#endif + /* Flush fifo if required */ + if (csr & MUSB_TXCSR_TXPKTRDY) + writew(csr | MUSB_TXCSR_FLUSHFIFO, + &musbr->txcsr); + } else { + /* Configure fifo size and fifo base address */ + config_fifo(rx, idx, fifoaddr); + + csr = readw(&musbr->rxcsr); +#if defined(CONFIG_MUSB_HCD) + /* clear the data toggle bit */ + writew(csr | MUSB_RXCSR_CLRDATATOG, &musbr->rxcsr); +#endif + /* Flush fifo if required */ + if (csr & MUSB_RXCSR_RXPKTRDY) + writew(csr | MUSB_RXCSR_FLUSHFIFO, + &musbr->rxcsr); + } + fifoaddr += epinfo->epsize; + epinfo++; + } +} + +/* + * This function writes data to endpoint fifo + * + * ep - endpoint number + * length - number of bytes to write to FIFO + * fifo_data - Pointer to data buffer that contains the data to write + */ +__attribute__((weak)) +void write_fifo(u8 ep, u32 length, void *fifo_data) +{ + u8 *data = (u8 *)fifo_data; + + /* select the endpoint index */ + writeb(ep, &musbr->index); + + /* write the data to the fifo */ + while (length--) + writeb(*data++, &musbr->fifox[ep]); +} + +/* + * AM35x supports only 32bit read operations so + * use seperate read_fifo() function for it. + */ +#ifndef CONFIG_USB_AM35X +/* + * This function reads data from endpoint fifo + * + * ep - endpoint number + * length - number of bytes to read from FIFO + * fifo_data - pointer to data buffer into which data is read + */ +__attribute__((weak)) +void read_fifo(u8 ep, u32 length, void *fifo_data) +{ + u8 *data = (u8 *)fifo_data; + + /* select the endpoint index */ + writeb(ep, &musbr->index); + + /* read the data to the fifo */ + while (length--) + *data++ = readb(&musbr->fifox[ep]); +} +#endif /* CONFIG_USB_AM35X */ |
