diff options
Diffstat (limited to 'include/status_led.h')
| -rw-r--r-- | include/status_led.h | 340 |
1 files changed, 340 insertions, 0 deletions
diff --git a/include/status_led.h b/include/status_led.h new file mode 100644 index 0000000..27e9127 --- /dev/null +++ b/include/status_led.h @@ -0,0 +1,340 @@ +/* + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * The purpose of this code is to signal the operational status of a + * target which usually boots over the network; while running in + * PCBoot, a status LED is blinking. As soon as a valid BOOTP reply + * message has been received, the LED is turned off. The Linux + * kernel, once it is running, will start blinking the LED again, + * with another frequency. + */ + +#ifndef _STATUS_LED_H_ +#define _STATUS_LED_H_ + +#ifdef CONFIG_STATUS_LED + +#define STATUS_LED_OFF 0 +#define STATUS_LED_BLINKING 1 +#define STATUS_LED_ON 2 + +void status_led_tick (unsigned long timestamp); +void status_led_set (int led, int state); + +/***** TQM8xxL ********************************************************/ +#if defined(CONFIG_TQM8xxL) +# define STATUS_LED_PAR im_cpm.cp_pbpar +# define STATUS_LED_DIR im_cpm.cp_pbdir +# define STATUS_LED_ODR im_cpm.cp_pbodr +# define STATUS_LED_DAT im_cpm.cp_pbdat + +# define STATUS_LED_BIT 0x00000001 +# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +# define STATUS_LED_STATE STATUS_LED_BLINKING + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ + +# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +/***** MVS v1 **********************************************************/ +#elif (defined(CONFIG_MVS) && CONFIG_MVS < 2) +# define STATUS_LED_PAR im_ioport.iop_pdpar +# define STATUS_LED_DIR im_ioport.iop_pddir +# undef STATUS_LED_ODR +# define STATUS_LED_DAT im_ioport.iop_pddat + +# define STATUS_LED_BIT 0x00000001 +# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +# define STATUS_LED_STATE STATUS_LED_BLINKING + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ + +# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +/***** GEN860T *********************************************************/ +#elif defined(CONFIG_GEN860T) + +# define STATUS_LED_PAR im_ioport.iop_papar +# define STATUS_LED_DIR im_ioport.iop_padir +# define STATUS_LED_ODR im_ioport.iop_paodr +# define STATUS_LED_DAT im_ioport.iop_padat + +# define STATUS_LED_BIT 0x0800 /* Red LED 0 is on PA.4 */ +# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) +# define STATUS_LED_STATE STATUS_LED_OFF +# define STATUS_LED_BIT1 0x0400 /* Grn LED 1 is on PA.5 */ +# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 8) +# define STATUS_LED_STATE1 STATUS_LED_BLINKING +# define STATUS_LED_BIT2 0x0080 /* Red LED 2 is on PA.8 */ +# define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 4) +# define STATUS_LED_STATE2 STATUS_LED_OFF +# define STATUS_LED_BIT3 0x0040 /* Grn LED 3 is on PA.9 */ +# define STATUS_LED_PERIOD3 (CONFIG_SYS_HZ / 4) +# define STATUS_LED_STATE3 STATUS_LED_OFF + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ +# define STATUS_LED_BOOT 1 /* Boot status on LED 1 */ + +/***** IVMS8 **********************************************************/ +#elif defined(CONFIG_IVMS8) + +# define STATUS_LED_PAR im_cpm.cp_pbpar +# define STATUS_LED_DIR im_cpm.cp_pbdir +# define STATUS_LED_ODR im_cpm.cp_pbodr +# define STATUS_LED_DAT im_cpm.cp_pbdat + +# define STATUS_LED_BIT 0x00000010 /* LED 0 is on PB.27 */ +# define STATUS_LED_PERIOD (1 * CONFIG_SYS_HZ) +# define STATUS_LED_STATE STATUS_LED_OFF +# define STATUS_LED_BIT1 0x00000020 /* LED 1 is on PB.26 */ +# define STATUS_LED_PERIOD1 (1 * CONFIG_SYS_HZ) +# define STATUS_LED_STATE1 STATUS_LED_OFF +/* IDE LED usable for other purposes, too */ +# define STATUS_LED_BIT2 0x00000008 /* LED 2 is on PB.28 */ +# define STATUS_LED_PERIOD2 (1 * CONFIG_SYS_HZ) +# define STATUS_LED_STATE2 STATUS_LED_OFF + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ + +# define STATUS_ILOCK_SWITCH 0x00800000 /* ILOCK switch in IRQ4 */ + +# define STATUS_ILOCK_PERIOD (CONFIG_SYS_HZ / 10) /* about every 100 ms */ + +# define STATUS_LED_YELLOW 0 +# define STATUS_LED_GREEN 1 +# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */ + +/***** IVML24 *********************************************************/ +#elif defined(CONFIG_IVML24) + +# define STATUS_LED_PAR im_cpm.cp_pbpar +# define STATUS_LED_DIR im_cpm.cp_pbdir +# define STATUS_LED_ODR im_cpm.cp_pbodr +# define STATUS_LED_DAT im_cpm.cp_pbdat + +# define STATUS_LED_BIT 0x00000010 /* LED 0 is on PB.27 */ +# define STATUS_LED_PERIOD (1 * CONFIG_SYS_HZ) +# define STATUS_LED_STATE STATUS_LED_OFF +# define STATUS_LED_BIT1 0x00000020 /* LED 1 is on PB.26 */ +# define STATUS_LED_PERIOD1 (1 * CONFIG_SYS_HZ) +# define STATUS_LED_STATE1 STATUS_LED_OFF +/* IDE LED usable for other purposes, too */ +# define STATUS_LED_BIT2 0x00000008 /* LED 2 is on PB.28 */ +# define STATUS_LED_PERIOD2 (1 * CONFIG_SYS_HZ) +# define STATUS_LED_STATE2 STATUS_LED_OFF + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ + +# define STATUS_ILOCK_SWITCH 0x00004000 /* ILOCK is on PB.17 */ + +# define STATUS_ILOCK_PERIOD (CONFIG_SYS_HZ / 10) /* about every 100 ms */ + +# define STATUS_LED_YELLOW 0 +# define STATUS_LED_GREEN 1 +# define STATUS_LED_BOOT 2 /* IDE LED used for boot status */ + +/***** ICU862 ********************************************************/ +#elif defined(CONFIG_ICU862) + +# define STATUS_LED_PAR im_ioport.iop_papar +# define STATUS_LED_DIR im_ioport.iop_padir +# define STATUS_LED_ODR im_ioport.iop_paodr +# define STATUS_LED_DAT im_ioport.iop_padat + +# define STATUS_LED_BIT 0x4000 /* LED 0 is on PA.1 */ +# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +# define STATUS_LED_STATE STATUS_LED_BLINKING +# define STATUS_LED_BIT1 0x1000 /* LED 1 is on PA.3 */ +# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ) +# define STATUS_LED_STATE1 STATUS_LED_OFF + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ + +# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +/***** Someone else defines these *************************************/ +#elif defined(STATUS_LED_PAR) + + /* + * ADVICE: Define in your board configuration file rather than + * filling this file up with lots of custom board stuff. + */ + +/***** NetVia ********************************************************/ +#elif defined(CONFIG_NETVIA) + +#if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1 + +#define STATUS_LED_PAR im_ioport.iop_pdpar +#define STATUS_LED_DIR im_ioport.iop_pddir +#undef STATUS_LED_ODR +#define STATUS_LED_DAT im_ioport.iop_pddat + +# define STATUS_LED_BIT 0x0080 /* PD.8 */ +# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +# define STATUS_LED_STATE STATUS_LED_BLINKING + +# define STATUS_LED_BIT1 0x0040 /* PD.9 */ +# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) +# define STATUS_LED_STATE1 STATUS_LED_OFF + +# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ +# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +#endif + +/***** CMI ********************************************************/ +#elif defined(CONFIG_CMI) +# define STATUS_LED_DIR im_mios.mios_mpiosm32ddr +# define STATUS_LED_DAT im_mios.mios_mpiosm32dr + +# define STATUS_LED_BIT 0x2000 /* Select one of the 16 possible*/ + /* MIOS outputs */ +# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) /* Blinking periode is 500 ms */ +# define STATUS_LED_STATE STATUS_LED_BLINKING + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 0 */ +# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +/***** KUP4K, KUP4X ****************************************************/ +#elif defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X) + +# define STATUS_LED_PAR im_ioport.iop_papar +# define STATUS_LED_DIR im_ioport.iop_padir +# define STATUS_LED_ODR im_ioport.iop_paodr +# define STATUS_LED_DAT im_ioport.iop_padat + +# define STATUS_LED_BIT 0x00000300 /* green + red PA[8]=yellow, PA[7]=red, PA[6]=green */ +# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +# define STATUS_LED_STATE STATUS_LED_BLINKING + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ + +# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +#elif defined(CONFIG_SVM_SC8xx) +# define STATUS_LED_PAR im_cpm.cp_pbpar +# define STATUS_LED_DIR im_cpm.cp_pbdir +# define STATUS_LED_ODR im_cpm.cp_pbodr +# define STATUS_LED_DAT im_cpm.cp_pbdat + +# define STATUS_LED_BIT 0x00000001 +# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +# define STATUS_LED_STATE STATUS_LED_BLINKING + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ + +# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +/***** RBC823 ********************************************************/ +#elif defined(CONFIG_RBC823) + +# define STATUS_LED_PAR im_ioport.iop_pcpar +# define STATUS_LED_DIR im_ioport.iop_pcdir +# undef STATUS_LED_ODR +# define STATUS_LED_DAT im_ioport.iop_pcdat + +# define STATUS_LED_BIT 0x0002 /* LED 0 is on PC.14 */ +# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +# define STATUS_LED_STATE STATUS_LED_BLINKING +# define STATUS_LED_BIT1 0x0004 /* LED 1 is on PC.13 */ +# define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ) +# define STATUS_LED_STATE1 STATUS_LED_OFF + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ + +# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +/***** NetPhone ********************************************************/ +#elif defined(CONFIG_NETPHONE) || defined(CONFIG_NETTA2) +/* XXX empty just to avoid the error */ +/***** STx XTc ********************************************************/ +#elif defined(CONFIG_STXXTC) +/* XXX empty just to avoid the error */ +/************************************************************************/ +#elif defined(CONFIG_V38B) + +# define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */ +# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +# define STATUS_LED_STATE STATUS_LED_BLINKING + +# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ +# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +#elif defined(CONFIG_MOTIONPRO) + +#define STATUS_LED_BIT ((vu_long *) MPC5XXX_GPT6_ENABLE) +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 10) +#define STATUS_LED_STATE STATUS_LED_BLINKING + +#define STATUS_LED_BIT1 ((vu_long *) MPC5XXX_GPT7_ENABLE) +#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 10) +#define STATUS_LED_STATE1 STATUS_LED_OFF + +#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +#elif defined(CONFIG_BOARD_SPECIFIC_LED) +/* led_id_t is unsigned long mask */ +typedef unsigned long led_id_t; + +extern void __led_toggle (led_id_t mask); +extern void __led_init (led_id_t mask, int state); +extern void __led_set (led_id_t mask, int state); +#else +# error Status LED configuration missing +#endif +/************************************************************************/ + +#ifndef CONFIG_BOARD_SPECIFIC_LED +# include <asm/status_led.h> +#endif + +/* + * Coloured LEDs API + */ +#ifndef __ASSEMBLY__ +extern void coloured_LED_init (void); +extern void red_led_on(void); +extern void red_led_off(void); +extern void green_led_on(void); +extern void green_led_off(void); +extern void yellow_led_on(void); +extern void yellow_led_off(void); +extern void blue_led_on(void); +extern void blue_led_off(void); +#else + .extern LED_init + .extern red_led_on + .extern red_led_off + .extern yellow_led_on + .extern yellow_led_off + .extern green_led_on + .extern green_led_off + .extern blue_led_on + .extern blue_led_off +#endif + +#endif /* CONFIG_STATUS_LED */ + +#endif /* _STATUS_LED_H_ */ |
