diff options
Diffstat (limited to 'board/amcc/yosemite/yosemite.c')
| -rw-r--r-- | board/amcc/yosemite/yosemite.c | 373 |
1 files changed, 373 insertions, 0 deletions
diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c new file mode 100644 index 0000000..0c95c36 --- /dev/null +++ b/board/amcc/yosemite/yosemite.c @@ -0,0 +1,373 @@ +/* + * (C) Copyright 2006-2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/ppc4xx.h> +#include <asm/processor.h> +#include <asm/io.h> +#include <spd_sdram.h> +#include <libfdt.h> +#include <fdt_support.h> + +DECLARE_GLOBAL_DATA_PTR; + +extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +static inline u32 get_async_pci_freq(void) +{ + if (in_8((void *)(CONFIG_SYS_BCSR_BASE + 5)) & + CONFIG_SYS_BCSR5_PCI66EN) + return 66666666; + else + return 33333333; +} + +int board_early_init_f(void) +{ + register uint reg; + + /*-------------------------------------------------------------------- + * Setup the external bus controller/chip selects + *-------------------------------------------------------------------*/ + mtdcr(EBC0_CFGADDR, EBC0_CFG); + reg = mfdcr(EBC0_CFGDATA); + mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */ + + /*-------------------------------------------------------------------- + * Setup the GPIO pins + *-------------------------------------------------------------------*/ + /*CPLD cs */ + /*setup Address lines for flash size 64Meg. */ + out32(GPIO0_OSRL, in32(GPIO0_OSRL) | 0x50010000); + out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x50010000); + out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x50000000); + + /*setup emac */ + out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xC080); + out32(GPIO0_TSRL, in32(GPIO0_TSRL) | 0x40); + out32(GPIO0_ISR1L, in32(GPIO0_ISR1L) | 0x55); + out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0x50004000); + out32(GPIO0_ISR1H, in32(GPIO0_ISR1H) | 0x00440000); + + /*UART1 */ + out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x02000000); + out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x00080000); + out32(GPIO1_ISR2L, in32(GPIO1_ISR2L) | 0x00010000); + + /* external interrupts IRQ0...3 */ + out32(GPIO1_TCR, in32(GPIO1_TCR) & ~0x00f00000); + out32(GPIO1_TSRL, in32(GPIO1_TSRL) & ~0x0000ff00); + out32(GPIO1_ISR1L, in32(GPIO1_ISR1L) | 0x00005500); + +#ifdef CONFIG_440EP + /*setup USB 2.0 */ + out32(GPIO1_TCR, in32(GPIO1_TCR) | 0xc0000000); + out32(GPIO1_OSRL, in32(GPIO1_OSRL) | 0x50000000); + out32(GPIO0_TCR, in32(GPIO0_TCR) | 0xf); + out32(GPIO0_OSRH, in32(GPIO0_OSRH) | 0xaa); + out32(GPIO0_ISR2H, in32(GPIO0_ISR2H) | 0x00000500); +#endif + + /*-------------------------------------------------------------------- + * Setup the interrupt controller polarities, triggers, etc. + *-------------------------------------------------------------------*/ + mtdcr(UIC0SR, 0xffffffff); /* clear all */ + mtdcr(UIC0ER, 0x00000000); /* disable all */ + mtdcr(UIC0CR, 0x00000009); /* ATI & UIC1 crit are critical */ + mtdcr(UIC0PR, 0xfffffe13); /* per ref-board manual */ + mtdcr(UIC0TR, 0x01c00008); /* per ref-board manual */ + mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(UIC0SR, 0xffffffff); /* clear all */ + + mtdcr(UIC1SR, 0xffffffff); /* clear all */ + mtdcr(UIC1ER, 0x00000000); /* disable all */ + mtdcr(UIC1CR, 0x00000000); /* all non-critical */ + mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */ + mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */ + mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */ + mtdcr(UIC1SR, 0xffffffff); /* clear all */ + + /*-------------------------------------------------------------------- + * Setup other serial configuration + *-------------------------------------------------------------------*/ + mfsdr(SDR0_PCI0, reg); + mtsdr(SDR0_PCI0, 0x80000000 | reg); /* PCI arbiter enabled */ + mtsdr(SDR0_PFC0, 0x00003e00); /* Pin function */ + mtsdr(SDR0_PFC1, 0x00048000); /* Pin function: UART0 has 4 pins */ + + /* Check and reconfigure the PCI sync clock if necessary */ + ppc4xx_pci_sync_clock_config(get_async_pci_freq()); + + /*clear tmrclk divisor */ + *(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x04) = 0x00; + + /*enable ethernet */ + *(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x08) = 0xf0; + +#ifdef CONFIG_440EP + /*enable usb 1.1 fs device and remove usb 2.0 reset */ + *(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x09) = 0x00; +#endif + + /*get rid of flash write protect */ + *(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x07) = 0x00; + + return 0; +} + +int misc_init_r (void) +{ + uint pbcr; + int size_val = 0; + + /* Re-do sizing to get full correct info */ + mtdcr(EBC0_CFGADDR, PB0CR); + pbcr = mfdcr(EBC0_CFGDATA); + switch (gd->bd->bi_flashsize) { + case 1 << 20: + size_val = 0; + break; + case 2 << 20: + size_val = 1; + break; + case 4 << 20: + size_val = 2; + break; + case 8 << 20: + size_val = 3; + break; + case 16 << 20: + size_val = 4; + break; + case 32 << 20: + size_val = 5; + break; + case 64 << 20: + size_val = 6; + break; + case 128 << 20: + size_val = 7; + break; + } + pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); + mtdcr(EBC0_CFGADDR, PB0CR); + mtdcr(EBC0_CFGDATA, pbcr); + + /* adjust flash start and offset */ + gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; + gd->bd->bi_flashoffset = 0; + + /* Monitor protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + -CONFIG_SYS_MONITOR_LEN, + 0xffffffff, + &flash_info[0]); + + return 0; +} + +int checkboard(void) +{ + char buf[64]; + int i = getenv_f("serial#", buf, sizeof(buf)); + u8 rev; + u32 clock = get_async_pci_freq(); + +#ifdef CONFIG_440EP + printf("Board: Yosemite - AMCC PPC440EP Evaluation Board"); +#else + printf("Board: Yellowstone - AMCC PPC440GR Evaluation Board"); +#endif + + rev = in_8((void *)(CONFIG_SYS_BCSR_BASE + 0)); + printf(", Rev. %X, PCI-Async=%d MHz", rev, clock / 1000000); + + if (i > 0) { + puts(", serial# "); + puts(buf); + } + putc('\n'); + + /* + * Reconfiguration of the PCI sync clock is already done, + * now check again if everything is in range: + */ + if (ppc4xx_pci_sync_clock_config(clock)) { + printf("ERROR: PCI clocking incorrect (async=%d " + "sync=%ld)!\n", clock, get_PCI_freq()); + } + + return (0); +} + +/************************************************************************* + * initdram -- doesn't use serial presence detect. + * + * Assumes: 256 MB, ECC, non-registered + * PLB @ 133 MHz + * + ************************************************************************/ +#define NUM_TRIES 64 +#define NUM_READS 10 + +void sdram_tr1_set(int ram_address, int* tr1_value) +{ + int i; + int j, k; + volatile unsigned int* ram_pointer = (unsigned int*)ram_address; + int first_good = -1, last_bad = 0x1ff; + + unsigned long test[NUM_TRIES] = { + 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, + 0x00000000, 0x00000000, 0xFFFFFFFF, 0xFFFFFFFF, + 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, + 0xFFFFFFFF, 0xFFFFFFFF, 0x00000000, 0x00000000, + 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, + 0xAAAAAAAA, 0xAAAAAAAA, 0x55555555, 0x55555555, + 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, + 0x55555555, 0x55555555, 0xAAAAAAAA, 0xAAAAAAAA, + 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, + 0xA5A5A5A5, 0xA5A5A5A5, 0x5A5A5A5A, 0x5A5A5A5A, + 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, + 0x5A5A5A5A, 0x5A5A5A5A, 0xA5A5A5A5, 0xA5A5A5A5, + 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, + 0xAA55AA55, 0xAA55AA55, 0x55AA55AA, 0x55AA55AA, + 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55, + 0x55AA55AA, 0x55AA55AA, 0xAA55AA55, 0xAA55AA55 }; + + /* go through all possible SDRAM0_TR1[RDCT] values */ + for (i=0; i<=0x1ff; i++) { + /* set the current value for TR1 */ + mtsdram(SDRAM0_TR1, (0x80800800 | i)); + + /* write values */ + for (j=0; j<NUM_TRIES; j++) { + ram_pointer[j] = test[j]; + + /* clear any cache at ram location */ + __asm__("dcbf 0,%0": :"r" (&ram_pointer[j])); + } + + /* read values back */ + for (j=0; j<NUM_TRIES; j++) { + for (k=0; k<NUM_READS; k++) { + /* clear any cache at ram location */ + __asm__("dcbf 0,%0": :"r" (&ram_pointer[j])); + + if (ram_pointer[j] != test[j]) + break; + } + + /* read error */ + if (k != NUM_READS) { + break; + } + } + + /* we have a SDRAM0_TR1[RDCT] that is part of the window */ + if (j == NUM_TRIES) { + if (first_good == -1) + first_good = i; /* found beginning of window */ + } else { /* bad read */ + /* if we have not had a good read then don't care */ + if(first_good != -1) { + /* first failure after a good read */ + last_bad = i-1; + break; + } + } + } + + /* return the current value for TR1 */ + *tr1_value = (first_good + last_bad) / 2; +} + +phys_size_t initdram(int board) +{ + register uint reg; + int tr1_bank1, tr1_bank2; + + /*-------------------------------------------------------------------- + * Setup some default + *------------------------------------------------------------------*/ + mtsdram(SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */ + mtsdram(SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */ + mtsdram(SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */ + mtsdram(SDRAM0_CLKTR, 0x40000000); /* ?? */ + mtsdram(SDRAM0_WDDCTR, 0x40000000); /* ?? */ + + /*clear this first, if the DDR is enabled by a debugger + then you can not make changes. */ + mtsdram(SDRAM0_CFG0, 0x00000000); /* Disable EEC */ + + /*-------------------------------------------------------------------- + * Setup for board-specific specific mem + *------------------------------------------------------------------*/ + /* + * Following for CAS Latency = 2.5 @ 133 MHz PLB + */ + mtsdram(SDRAM0_B0CR, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */ + mtsdram(SDRAM0_B1CR, 0x080a4001); /* SDBA=0x080 128MB, Mode 3, enabled */ + + mtsdram(SDRAM0_TR0, 0x410a4012); /* ?? */ + mtsdram(SDRAM0_RTR, 0x04080000); /* ?? */ + mtsdram(SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM */ + mtsdram(SDRAM0_CFG0, 0x30000000); /* Disable EEC */ + udelay(400); /* Delay 200 usecs (min) */ + + /*-------------------------------------------------------------------- + * Enable the controller, then wait for DCEN to complete + *------------------------------------------------------------------*/ + mtsdram(SDRAM0_CFG0, 0x80000000); /* Enable */ + + for (;;) { + mfsdram(SDRAM0_MCSTS, reg); + if (reg & 0x80000000) + break; + } + + sdram_tr1_set(0x00000000, &tr1_bank1); + sdram_tr1_set(0x08000000, &tr1_bank2); + mtsdram(SDRAM0_TR1, (((tr1_bank1+tr1_bank2)/2) | 0x80800800)); + + return CONFIG_SYS_SDRAM_BANKS * (CONFIG_SYS_KBYTES_SDRAM * 1024); /* return bytes */ +} + +/************************************************************************* + * hw_watchdog_reset + * + * This routine is called to reset (keep alive) the watchdog timer + * + ************************************************************************/ +#if defined(CONFIG_HW_WATCHDOG) +void hw_watchdog_reset(void) +{ + +} +#endif + +void board_reset(void) +{ + /* give reset to BCSR */ + *(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x06) = 0x09; +} |
