1 files changed, 146 insertions, 0 deletions
diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c
new file mode 100644
index 0000000..a697c19
--- /dev/null
+++ b/board/Marvell/gplugd/gplugd.c
@@ -0,0 +1,146 @@
+/*
+ * (C) Copyright 2011
+ * eInfochips Ltd. <www.einfochips.com>
+ * Written-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
+ *
+ * Based on Aspenite:
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ * Contributor: Mahavir Jain <mjain@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <mvmfp.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/mfp.h>
+#include <asm/arch/armada100.h>
+#include <asm/gpio.h>
+#include <miiphy.h>
+
+#ifdef CONFIG_ARMADA100_FEC
+#include <net.h>
+#include <netdev.h>
+#endif /* CONFIG_ARMADA100_FEC */
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	u32 mfp_cfg[] = {
+		/* I2C */
+		MFP105_CI2C_SDA,
+		MFP106_CI2C_SCL,
+
+		/* Enable Console on UART3 */
+		MFPO8_UART3_TXD,
+		MFPO9_UART3_RXD,
+
+		/* Ethernet PHY Interface */
+		MFP086_ETH_TXCLK,
+		MFP087_ETH_TXEN,
+		MFP088_ETH_TXDQ3,
+		MFP089_ETH_TXDQ2,
+		MFP090_ETH_TXDQ1,
+		MFP091_ETH_TXDQ0,
+		MFP092_ETH_CRS,
+		MFP093_ETH_COL,
+		MFP094_ETH_RXCLK,
+		MFP095_ETH_RXER,
+		MFP096_ETH_RXDQ3,
+		MFP097_ETH_RXDQ2,
+		MFP098_ETH_RXDQ1,
+		MFP099_ETH_RXDQ0,
+		MFP100_ETH_MDC,
+		MFP101_ETH_MDIO,
+		MFP103_ETH_RXDV,
+
+		/* SSP2 */
+		MFP107_SSP2_RXD,
+		MFP108_SSP2_TXD,
+		MFP110_SSP2_CS,
+		MFP111_SSP2_CLK,
+
+		MFP_EOC		/*End of configuration*/
+	};
+	/* configure MFP's */
+	mfp_config(mfp_cfg);
+	return 0;
+}
+
+int board_init(void)
+{
+	struct armd1apb2_registers *apb2_regs =
+		(struct armd1apb2_registers *)ARMD1_APBC2_BASE;
+
+	/* arch number of Board */
+	gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD;
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100;
+	/* Assert PHY_RST# */
+	gpio_direction_output(CONFIG_SYS_GPIO_PHY_RST, GPIO_LOW);
+	udelay(10);
+	/* Deassert PHY_RST# */
+	gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_HIGH);
+
+	/* Enable SSP2 clock */
+	writel(SSP2_APBCLK | SSP2_FNCLK, &apb2_regs->ssp2_clkrst);
+	return 0;
+}
+
+#ifdef CONFIG_ARMADA100_FEC
+int board_eth_init(bd_t *bis)
+{
+	struct armd1apmu_registers *apmu_regs =
+		(struct armd1apmu_registers *)ARMD1_APMU_BASE;
+
+	/* Enable clock of ethernet controller */
+	writel(FE_CLK_RST | FE_CLK_ENA, &apmu_regs->fecrc);
+
+	return armada100_fec_register(ARMD1_FEC_BASE);
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and initialize PHY chip 88E3015 */
+void reset_phy(void)
+{
+	u16 phy_adr;
+	const char *name = "armd-fec0";
+
+	if (miiphy_set_current_dev(name))
+		return;
+
+	/* command to read PHY dev address */
+	if (miiphy_read(name, 0xff, 0xff, &phy_adr)) {
+		printf("Err..%s could not read PHY dev address\n", __func__);
+		return;
+	}
+
+	/* Set Ethernet LED in TX blink mode */
+	miiphy_write(name, phy_adr, PHY_LED_MAN_REG, 0x00);
+	miiphy_write(name, phy_adr, PHY_LED_PAR_SEL_REG, PHY_LED_VAL);
+
+	/* reset the phy */
+	miiphy_reset(name, phy_adr);
+	debug("88E3015 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
+#endif /* CONFIG_ARMADA100_FEC */