blob: 3946fd184445be76eb97fe4625d1178a749b8d0a (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
|
# I'm assuming this is an AP135-020. The AP136-010 in openwrt has
# the ethernet ports wired up to the switch in the reverse way.
# $FreeBSD$
# QCA955X_ETH_CFG_RGMII_EN (1 << 0)
hint.qca955x_gmac.0.gmac_cfg=0x1
# Use this to derive ath0 from arge0 MAC address.
# 0x1ffe0004 is the arge0 MAC; but it's also the "unit MAC".
# So make that the ath0 MAC, and make arge0 -1 from that.
# ath0: offset 0
# arge0: offset -1
# arge1: use +1 from the arge0 MAC, even though
# there's a secondary MAC address configured in EEPROM
# at 0x1ffe0018.
hint.ar71xx.0.eeprom_mac_addr=0x1ffe0004
hint.ar71xx.0.eeprom_mac_isascii=1
hint.ar71xx_mac_map.0.devid=ath
hint.ar71xx_mac_map.0.unitid=0
hint.ar71xx_mac_map.0.offset=0
hint.ar71xx_mac_map.0.is_local=0
hint.ar71xx_mac_map.1.devid=arge
hint.ar71xx_mac_map.1.unitid=0
hint.ar71xx_mac_map.1.offset=-1
hint.ar71xx_mac_map.1.is_local=0
hint.ar71xx_mac_map.2.devid=arge
hint.ar71xx_mac_map.2.unitid=1
hint.ar71xx_mac_map.2.offset=1
hint.ar71xx_mac_map.2.is_local=0
# mdiobus0 on arge0
hint.argemdio.0.at="nexus0"
hint.argemdio.0.maddr=0x19000000
hint.argemdio.0.msize=0x1000
hint.argemdio.0.order=0
# mdiobus1 on arge1 - required to bring up arge1?
hint.argemdio.1.at="nexus0"
hint.argemdio.1.maddr=0x1a000000
hint.argemdio.1.msize=0x1000
hint.argemdio.1.order=0
# AR8327 - connected via mdiobus0 on arge0
hint.arswitch.0.at="mdio0"
hint.arswitch.0.is_7240=0 # definitely not the internal switch!
hint.arswitch.0.is_9340=0 # not the internal switch!
hint.arswitch.0.numphys=5 # all ports are PHYs
hint.arswitch.0.phy4cpu=0
hint.arswitch.0.is_rgmii=0 # not needed
hint.arswitch.0.is_gmii=0 # not needed
# This is where it gets a bit odd. port 0 and port 6 are CPU ports.
# The current code only supports one CPU port. So hm, what should
# we do to hook PAD6 up to be RGMII but a PHY, not a MAC?
# The other trick - how do we get arge1 (hooked up to GMAC0) to work?
# That's currently supposed to be hooked up to CPU port 0.
# Other AR8327 configuration parameters
# AP136-020 parameters
# GMAC0 AR8327 -> GMAC1 (arge1) SoC, SGMII
# AR8327_PAD_MAC_SGMII
hint.arswitch.0.pad.0.mode=3
#hint.arswitch.0.pad.0.rxclk_delay_sel=0
hint.arswitch.0.pad.0.sgmii_delay_en=1
# GMAC6 AR8327 -> GMAC0 (arge0) SoC, RGMII
# AR8327_PAD_MAC_RGMII
# XXX I think this hooks it up to the internal MAC6
hint.arswitch.0.pad.6.mode=6
hint.arswitch.0.pad.6.txclk_delay_en=1
hint.arswitch.0.pad.6.rxclk_delay_en=1
# AR8327_CLK_DELAY_SEL1
hint.arswitch.0.pad.6.txclk_delay_sel=1
# AR8327_CLK_DELAY_SEL2
hint.arswitch.0.pad.6.rxclk_delay_sel=2
# XXX there's no LED management just yet!
hint.arswitch.0.led.ctrl0=0x00000000
hint.arswitch.0.led.ctrl1=0xc737c737
hint.arswitch.0.led.ctrl2=0x00000000
hint.arswitch.0.led.ctrl3=0x00c30c00
hint.arswitch.0.led.open_drain=1
# force_link=1 is required for the rest of the parameters
# to be configured.
hint.arswitch.0.port.0.force_link=1
hint.arswitch.0.port.0.speed=1000
hint.arswitch.0.port.0.duplex=1
hint.arswitch.0.port.0.txpause=1
hint.arswitch.0.port.0.rxpause=1
# force_link=1 is required for the rest of the parameters
# to be configured.
hint.arswitch.0.port.6.force_link=1
hint.arswitch.0.port.6.speed=1000
hint.arswitch.0.port.6.duplex=1
hint.arswitch.0.port.6.txpause=1
hint.arswitch.0.port.6.rxpause=1
# arge0 - hooked up to AR8327 GMAC6, RGMII
# set at 1000/full to the switch.
# so, lock both sides of this connect up to 1000/full;
# if_arge thus wont change the PLL configuration
# upon a link status change.
hint.arge.0.phymask=0x0
hint.arge.0.miimode=3 # RGMII
hint.arge.0.media=1000
hint.arge.0.fduplex=1
hint.arge.0.pll_1000=0x56000000
# hint.arge.0.eeprommac=0x1ffe0004
# hint.arge.0.readascii=1
# arge1 - lock up to 1000/full
hint.arge.1.phymask=0x0
hint.arge.1.media=1000
hint.arge.1.fduplex=1
hint.arge.1.miimode=5 # SGMII
hint.arge.1.pll_1000=0x03000101
#hint.arge.1.eeprommac=0x1ffe0018
#hint.arge.1.readascii=1
# ath0: Where the ART is - last 64k in the flash
# Note: ath0 MAC is default (00:11:22:33:44:55) and thus
# requires replacing via the board MAC address map.
hint.ath.0.eepromaddr=0x1fff0000
hint.ath.0.eepromsize=16384
# 256KiB u-boot
hint.map.0.at="flash/spi0"
hint.map.0.start=0x00000000
hint.map.0.end=0x00040000 # 256k u-boot
hint.map.0.name="u-boot"
hint.map.0.readonly=1
# kernel
hint.map.1.at="flash/spi0"
hint.map.1.start=0x00040000
hint.map.1.end="search:0x00040000:0x10000:.!/bin/sh"
hint.map.1.name="kernel"
hint.map.1.readonly=1
# rootfs
hint.map.2.at="flash/spi0"
hint.map.2.start="search:0x00040000:0x10000:.!/bin/sh"
hint.map.2.end=0x007d0000
hint.map.2.name="rootfs"
hint.map.2.readonly=1
# 64KiB cfg
hint.map.3.at="flash/spi0"
hint.map.3.start=0x007d0000
hint.map.3.end=0x007e0000
hint.map.3.name="cfg"
hint.map.3.readonly=0
# 8256 KiB mib0
hint.map.4.at="flash/spi0"
hint.map.4.start=0x007e0000
hint.map.4.end=0x00ff0000 # 64k mib0
hint.map.4.name="mib0"
hint.map.4.readonly=1
# 64KiB ART
# XXX TODO: is this really here?
hint.map.5.at="flash/spi0"
hint.map.5.start=0x00ff0000
hint.map.5.end=0x01000000 # 64k ART
hint.map.5.name="ART"
hint.map.5.readonly=1
|