path: root/sys/dev/em/if_em_phy.h

/*******************************************************************************

  Copyright (c) 2001-2002 Intel Corporation 
  All rights reserved. 
  
  Redistribution and use in source and binary forms of the Software, with or 
  without modification, are permitted provided that the following conditions 
  are met: 
  
   1. Redistributions of source code of the Software may retain the above 
      copyright notice, this list of conditions and the following disclaimer.
   
   2. Redistributions in binary form of the Software may reproduce the above 
      copyright notice, this list of conditions and the following disclaimer 
      in the documentation and/or other materials provided with the 
      distribution. 
  
   3. Neither the name of the Intel Corporation nor the names of its 
      contributors shall be used to endorse or promote products derived from 
      this Software without specific prior written permission.
  
  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 
  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 
  ARE DISCLAIMED. IN NO EVENT SHALL THE INTEL OR ITS CONTRIBUTORS BE LIABLE 
  FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 
  DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 
  SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER 
  CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 
  LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 
  OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 
  SUCH DAMAGE.

*******************************************************************************/

/*$FreeBSD$*/
/* if_em_phy.h
 * Structures, enums, and macros for the PHY
 */

#ifndef _EM_PHY_H_
#define _EM_PHY_H_

#include <dev/em/if_em_osdep.h>

/* PHY status info structure and supporting enums */
typedef enum {
    em_cable_length_50 = 0,
    em_cable_length_50_80,
    em_cable_length_80_110,
    em_cable_length_110_140,
    em_cable_length_140,
    em_cable_length_undefined = 0xFF
} em_cable_length;

typedef enum {
    em_10bt_ext_dist_enable_normal = 0,
    em_10bt_ext_dist_enable_lower,
    em_10bt_ext_dist_enable_undefined = 0xFF
} em_10bt_ext_dist_enable;

typedef enum {
    em_rev_polarity_normal = 0,
    em_rev_polarity_reversed,
    em_rev_polarity_undefined = 0xFF
} em_rev_polarity;

typedef enum {
    em_polarity_reversal_enabled = 0,
    em_polarity_reversal_disabled,
    em_polarity_reversal_undefined = 0xFF
} em_polarity_reversal;

typedef enum {
    em_down_no_idle_no_detect = 0,
    em_down_no_idle_detect,
    em_down_no_idle_undefined = 0xFF
} em_down_no_idle;

typedef enum {
    em_auto_x_mode_manual_mdi = 0,
    em_auto_x_mode_manual_mdix,
    em_auto_x_mode_auto1,
    em_auto_x_mode_auto2,
    em_auto_x_mode_undefined = 0xFF
} em_auto_x_mode;

typedef enum {
    em_1000t_rx_status_not_ok = 0,
    em_1000t_rx_status_ok,
    em_1000t_rx_status_undefined = 0xFF
} em_1000t_rx_status;

struct em_phy_info {
    em_cable_length cable_length;
    em_10bt_ext_dist_enable extended_10bt_distance;
    em_rev_polarity cable_polarity;
    em_polarity_reversal polarity_correction;
    em_down_no_idle link_reset;
    em_auto_x_mode mdix_mode;
    em_1000t_rx_status local_rx;
    em_1000t_rx_status remote_rx;
};

struct em_phy_stats {
    uint32_t idle_errors;
    uint32_t receive_errors;
};

/* Function Prototypes */
uint16_t em_read_phy_reg(struct em_shared_adapter *shared, uint32_t reg_addr);
void em_write_phy_reg(struct em_shared_adapter *shared, uint32_t reg_addr, uint16_t data);
void em_phy_hw_reset(struct em_shared_adapter *shared);
boolean_t em_phy_reset(struct em_shared_adapter *shared);
boolean_t em_phy_setup(struct em_shared_adapter *shared, uint32_t ctrl_reg);
boolean_t em_phy_setup_autoneg(struct em_shared_adapter *shared);
void em_config_mac_to_phy(struct em_shared_adapter *shared, uint16_t mii_reg);
void em_config_collision_dist(struct em_shared_adapter *shared);
void em_display_mii(struct em_shared_adapter *shared);
boolean_t em_detect_gig_phy(struct em_shared_adapter *shared);
void em_phy_reset_dsp(struct em_shared_adapter *shared);
boolean_t em_wait_autoneg(struct em_shared_adapter *shared);
boolean_t em_phy_get_info(struct em_shared_adapter *shared, struct em_phy_info *phy_status_info);
boolean_t em_validate_mdi_setting(struct em_shared_adapter *shared);

/* Bit definitions for the Management Data IO (MDIO) and Management Data
 * Clock (MDC) pins in the Device Control Register.
 */
#define E1000_CTRL_PHY_RESET_DIR  E1000_CTRL_SWDPIO0
#define E1000_CTRL_PHY_RESET      E1000_CTRL_SWDPIN0
#define E1000_CTRL_MDIO_DIR       E1000_CTRL_SWDPIO2
#define E1000_CTRL_MDIO           E1000_CTRL_SWDPIN2
#define E1000_CTRL_MDC_DIR        E1000_CTRL_SWDPIO3
#define E1000_CTRL_MDC            E1000_CTRL_SWDPIN3
#define E1000_CTRL_PHY_RESET_DIR4 E1000_CTRL_EXT_SDP4_DIR
#define E1000_CTRL_PHY_RESET4     E1000_CTRL_EXT_SDP4_DATA

/* PHY 1000 MII Register/Bit Definitions */
/* PHY Registers defined by IEEE */
#define PHY_CTRL         0x00 /* Control Register */
#define PHY_STATUS       0x01 /* Status Regiser */
#define PHY_ID1          0x02 /* Phy Id Reg (word 1) */
#define PHY_ID2          0x03 /* Phy Id Reg (word 2) */
#define PHY_AUTONEG_ADV  0x04 /* Autoneg Advertisement */
#define PHY_LP_ABILITY   0x05 /* Link Partner Ability (Base Page) */
#define PHY_AUTONEG_EXP  0x06 /* Autoneg Expansion Reg */
#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */
#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */
#define PHY_1000T_CTRL   0x09 /* 1000Base-T Control Reg */
#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
#define PHY_EXT_STATUS   0x0F /* Extended Status Reg */

/* M88E1000 Specific Registers */
#define M88E1000_PHY_SPEC_CTRL     0x10  /* PHY Specific Control Register */
#define M88E1000_PHY_SPEC_STATUS   0x11  /* PHY Specific Status Register */
#define M88E1000_INT_ENABLE        0x12  /* Interrupt Enable Register */
#define M88E1000_INT_STATUS        0x13  /* Interrupt Status Register */
#define M88E1000_EXT_PHY_SPEC_CTRL 0x14  /* Extended PHY Specific Control */
#define M88E1000_RX_ERR_CNTR       0x15  /* Receive Error Counter */

#define MAX_PHY_REG_ADDRESS 0x1F        /* 5 bit address bus (0-0x1F) */

/* PHY Control Register */
#define MII_CR_SPEED_SELECT_MSB 0x0040  /* bits 6,13: 10=1000, 01=100, 00=10 */
#define MII_CR_COLL_TEST_ENABLE 0x0080  /* Collision test enable */
#define MII_CR_FULL_DUPLEX      0x0100  /* FDX =1, half duplex =0 */
#define MII_CR_RESTART_AUTO_NEG 0x0200  /* Restart auto negotiation */
#define MII_CR_ISOLATE          0x0400  /* Isolate PHY from MII */
#define MII_CR_POWER_DOWN       0x0800  /* Power down */
#define MII_CR_AUTO_NEG_EN      0x1000  /* Auto Neg Enable */
#define MII_CR_SPEED_SELECT_LSB 0x2000  /* bits 6,13: 10=1000, 01=100, 00=10 */
#define MII_CR_LOOPBACK         0x4000  /* 0 = normal, 1 = loopback */
#define MII_CR_RESET            0x8000  /* 0 = normal, 1 = PHY reset */

/* PHY Status Register */
#define MII_SR_EXTENDED_CAPS     0x0001 /* Extended register capabilities */
#define MII_SR_JABBER_DETECT     0x0002 /* Jabber Detected */
#define MII_SR_LINK_STATUS       0x0004 /* Link Status 1 = link */
#define MII_SR_AUTONEG_CAPS      0x0008 /* Auto Neg Capable */
#define MII_SR_REMOTE_FAULT      0x0010 /* Remote Fault Detect */
#define MII_SR_AUTONEG_COMPLETE  0x0020 /* Auto Neg Complete */
#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */
#define MII_SR_EXTENDED_STATUS   0x0100 /* Ext. status info in Reg 0x0F */
#define MII_SR_100T2_HD_CAPS     0x0200 /* 100T2 Half Duplex Capable */
#define MII_SR_100T2_FD_CAPS     0x0400 /* 100T2 Full Duplex Capable */
#define MII_SR_10T_HD_CAPS       0x0800 /* 10T   Half Duplex Capable */
#define MII_SR_10T_FD_CAPS       0x1000 /* 10T   Full Duplex Capable */
#define MII_SR_100X_HD_CAPS      0x2000 /* 100X  Half Duplex Capable */
#define MII_SR_100X_FD_CAPS      0x4000 /* 100X  Full Duplex Capable */
#define MII_SR_100T4_CAPS        0x8000 /* 100T4 Capable */

/* Autoneg Advertisement Register */
#define NWAY_AR_SELECTOR_FIELD 0x0001   /* indicates IEEE 802.3 CSMA/CD */
#define NWAY_AR_10T_HD_CAPS    0x0020   /* 10T   Half Duplex Capable */
#define NWAY_AR_10T_FD_CAPS    0x0040   /* 10T   Full Duplex Capable */
#define NWAY_AR_100TX_HD_CAPS  0x0080   /* 100TX Half Duplex Capable */
#define NWAY_AR_100TX_FD_CAPS  0x0100   /* 100TX Full Duplex Capable */
#define NWAY_AR_100T4_CAPS     0x0200   /* 100T4 Capable */
#define NWAY_AR_PAUSE          0x0400   /* Pause operation desired */
#define NWAY_AR_ASM_DIR        0x0800   /* Asymmetric Pause Direction bit */
#define NWAY_AR_REMOTE_FAULT   0x2000   /* Remote Fault detected */
#define NWAY_AR_NEXT_PAGE      0x8000   /* Next Page ability supported */

/* Link Partner Ability Register (Base Page) */
#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */
#define NWAY_LPAR_10T_HD_CAPS    0x0020 /* LP is 10T   Half Duplex Capable */
#define NWAY_LPAR_10T_FD_CAPS    0x0040 /* LP is 10T   Full Duplex Capable */
#define NWAY_LPAR_100TX_HD_CAPS  0x0080 /* LP is 100TX Half Duplex Capable */
#define NWAY_LPAR_100TX_FD_CAPS  0x0100 /* LP is 100TX Full Duplex Capable */
#define NWAY_LPAR_100T4_CAPS     0x0200 /* LP is 100T4 Capable */
#define NWAY_LPAR_PAUSE          0x0400 /* LP Pause operation desired */
#define NWAY_LPAR_ASM_DIR        0x0800 /* LP Asymmetric Pause Direction bit */
#define NWAY_LPAR_REMOTE_FAULT   0x2000 /* LP has detected Remote Fault */
#define NWAY_LPAR_ACKNOWLEDGE    0x4000 /* LP has rx'd link code word */
#define NWAY_LPAR_NEXT_PAGE      0x8000 /* Next Page ability supported */

/* Autoneg Expansion Register */
#define NWAY_ER_LP_NWAY_CAPS      0x0001 /* LP has Auto Neg Capability */
#define NWAY_ER_PAGE_RXD          0x0002 /* LP is 10T   Half Duplex Capable */
#define NWAY_ER_NEXT_PAGE_CAPS    0x0004 /* LP is 10T   Full Duplex Capable */
#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */
#define NWAY_ER_PAR_DETECT_FAULT  0x0100 /* LP is 100TX Full Duplex Capable */

/* Next Page TX Register */
#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
#define NPTX_TOGGLE         0x0800 /* Toggles between exchanges
                                    * of different NP
                                    */
#define NPTX_ACKNOWLDGE2    0x1000 /* 1 = will comply with msg
                                    * 0 = cannot comply with msg
                                    */
#define NPTX_MSG_PAGE       0x2000 /* formatted(1)/unformatted(0) pg */
#define NPTX_NEXT_PAGE      0x8000 /* 1 = addition NP will follow 
                                    * 0 = sending last NP
                                    */

/* Link Partner Next Page Register */
#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
#define LP_RNPR_TOGGLE         0x0800 /* Toggles between exchanges
                                       * of different NP
                                       */
#define LP_RNPR_ACKNOWLDGE2    0x1000 /* 1 = will comply with msg 
                                       * 0 = cannot comply with msg
                                       */
#define LP_RNPR_MSG_PAGE       0x2000  /* formatted(1)/unformatted(0) pg */
#define LP_RNPR_ACKNOWLDGE     0x4000  /* 1 = ACK / 0 = NO ACK */
#define LP_RNPR_NEXT_PAGE      0x8000  /* 1 = addition NP will follow
                                        * 0 = sending last NP 
                                        */

/* 1000BASE-T Control Register */
#define CR_1000T_ASYM_PAUSE      0x0080 /* Advertise asymmetric pause bit */
#define CR_1000T_HD_CAPS         0x0100 /* Advertise 1000T HD capability */
#define CR_1000T_FD_CAPS         0x0200 /* Advertise 1000T FD capability  */
#define CR_1000T_REPEATER_DTE    0x0400 /* 1=Repeater/switch device port */
                                        /* 0=DTE device */
#define CR_1000T_MS_VALUE        0x0800 /* 1=Configure PHY as Master */
                                        /* 0=Configure PHY as Slave */
#define CR_1000T_MS_ENABLE       0x1000 /* 1=Master/Slave manual config value */
                                        /* 0=Automatic Master/Slave config */
#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
#define CR_1000T_TEST_MODE_1     0x2000 /* Transmit Waveform test */
#define CR_1000T_TEST_MODE_2     0x4000 /* Master Transmit Jitter test */
#define CR_1000T_TEST_MODE_3     0x6000 /* Slave Transmit Jitter test */
#define CR_1000T_TEST_MODE_4     0x8000 /* Transmitter Distortion test */

/* 1000BASE-T Status Register */
#define SR_1000T_IDLE_ERROR_CNT   0x00FF /* Num idle errors since last read */
#define SR_1000T_ASYM_PAUSE_DIR   0x0100 /* LP asymmetric pause direction bit */
#define SR_1000T_LP_HD_CAPS       0x0400 /* LP is 1000T HD capable */
#define SR_1000T_LP_FD_CAPS       0x0800 /* LP is 1000T FD capable */
#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
#define SR_1000T_LOCAL_RX_STATUS  0x2000 /* Local receiver OK */
#define SR_1000T_MS_CONFIG_RES    0x4000 /* 1=Local TX is Master, 0=Slave */
#define SR_1000T_MS_CONFIG_FAULT  0x8000 /* Master/Slave config fault */
#define SR_1000T_REMOTE_RX_STATUS_SHIFT 12
#define SR_1000T_LOCAL_RX_STATUS_SHIFT  13

/* Extended Status Register */
#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */
#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */
#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */
#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */

#define PHY_TX_POLARITY_MASK   0x0100 /* register 10h bit 8 (polarity bit) */
#define PHY_TX_NORMAL_POLARITY 0      /* register 10h bit 8 (normal polarity) */

#define AUTO_POLARITY_DISABLE  0x0010 /* register 11h bit 4 */
                                      /* (0=enable, 1=disable) */

/* M88E1000 PHY Specific Control Register */
#define M88E1000_PSCR_JABBER_DISABLE    0x0001 /* 1=Jabber Function disabled */
#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
#define M88E1000_PSCR_SQE_TEST          0x0004 /* 1=SQE Test enabled */
#define M88E1000_PSCR_CLK125_DISABLE    0x0010 /* 1=CLK125 low, 
                                                * 0=CLK125 toggling
                                                */
#define M88E1000_PSCR_MDI_MANUAL_MODE  0x0000  /* MDI Crossover Mode bits 6:5 */
                                               /* Manual MDI configuration */
#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020  /* Manual MDIX configuration */
#define M88E1000_PSCR_AUTO_X_1000T     0x0040  /* 1000BASE-T: Auto crossover,
                                                *  100BASE-TX/10BASE-T: 
                                                *  MDI Mode
                                                */
#define M88E1000_PSCR_AUTO_X_MODE      0x0060  /* Auto crossover enabled 
                                                * all speeds. 
                                                */
#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE 0x0080 
                                        /* 1=Enable Extended 10BASE-T distance
                                         * (Lower 10BASE-T RX Threshold)
                                         * 0=Normal 10BASE-T RX Threshold */
#define M88E1000_PSCR_MII_5BIT_ENABLE      0x0100
                                        /* 1=5-Bit interface in 100BASE-TX
                                         * 0=MII interface in 100BASE-TX */
#define M88E1000_PSCR_SCRAMBLER_DISABLE    0x0200 /* 1=Scrambler disable */
#define M88E1000_PSCR_FORCE_LINK_GOOD      0x0400 /* 1=Force link good */
#define M88E1000_PSCR_ASSERT_CRS_ON_TX     0x0800 /* 1=Assert CRS on Transmit */

#define M88E1000_PSCR_POLARITY_REVERSAL_SHIFT    1
#define M88E1000_PSCR_AUTO_X_MODE_SHIFT          5
#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7

/* M88E1000 PHY Specific Status Register */
#define M88E1000_PSSR_JABBER             0x0001 /* 1=Jabber */
#define M88E1000_PSSR_REV_POLARITY       0x0002 /* 1=Polarity reversed */
#define M88E1000_PSSR_MDIX               0x0040 /* 1=MDIX; 0=MDI */
#define M88E1000_PSSR_CABLE_LENGTH       0x0380 /* 0=<50M;1=50-80M;2=80-110M;
                                            * 3=110-140M;4=>140M */
#define M88E1000_PSSR_LINK               0x0400 /* 1=Link up, 0=Link down */
#define M88E1000_PSSR_SPD_DPLX_RESOLVED  0x0800 /* 1=Speed & Duplex resolved */
#define M88E1000_PSSR_PAGE_RCVD          0x1000 /* 1=Page received */
#define M88E1000_PSSR_DPLX               0x2000 /* 1=Duplex 0=Half Duplex */
#define M88E1000_PSSR_SPEED              0xC000 /* Speed, bits 14:15 */
#define M88E1000_PSSR_10MBS              0x0000 /* 00=10Mbs */
#define M88E1000_PSSR_100MBS             0x4000 /* 01=100Mbs */
#define M88E1000_PSSR_1000MBS            0x8000 /* 10=1000Mbs */

#define M88E1000_PSSR_REV_POLARITY_SHIFT 1
#define M88E1000_PSSR_MDIX_SHIFT         6
#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7

/* M88E1000 Extended PHY Specific Control Register */
#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */
#define M88E1000_EPSCR_DOWN_NO_IDLE   0x8000 /* 1=Lost lock detect enabled.
                                              * Will assert lost lock and bring
                                              * link down if idle not seen
                                              * within 1ms in 1000BASE-T 
                                              */
#define M88E1000_EPSCR_TX_CLK_2_5     0x0060 /* 2.5 MHz TX_CLK */
#define M88E1000_EPSCR_TX_CLK_25      0x0070 /* 25  MHz TX_CLK */
#define M88E1000_EPSCR_TX_CLK_0       0x0000 /* NO  TX_CLK */

#define M88E1000_EPSCR_DOWN_NO_IDLE_SHIFT 15

/* Bit definitions for valid PHY IDs. */
#define M88E1000_12_PHY_ID 0x01410C50
#define M88E1000_14_PHY_ID 0x01410C40
#define M88E1000_I_PHY_ID  0x01410C30
#define M88E1011_I_PHY_ID  0x01410C20

/* Miscellaneous PHY bit definitions. */
#define PHY_PREAMBLE        0xFFFFFFFF
#define PHY_SOF             0x01
#define PHY_OP_READ         0x02
#define PHY_OP_WRITE        0x01
#define PHY_TURNAROUND      0x02
#define PHY_PREAMBLE_SIZE   32
#define MII_CR_SPEED_1000   0x0040
#define MII_CR_SPEED_100    0x2000
#define MII_CR_SPEED_10     0x0000
#define E1000_PHY_ADDRESS   0x01
#define PHY_AUTO_NEG_TIME   45  /* 4.5 Seconds */
#define PHY_FORCE_TIME      20  /* 2.0 Seconds */
#define PHY_REVISION_MASK   0xFFFFFFF0
#define DEVICE_SPEED_MASK   0x00000300  /* Device Ctrl Reg Speed Mask */
#define REG4_SPEED_MASK     0x01E0
#define REG9_SPEED_MASK     0x0300
#define ADVERTISE_10_HALF   0x0001
#define ADVERTISE_10_FULL   0x0002
#define ADVERTISE_100_HALF  0x0004
#define ADVERTISE_100_FULL  0x0008
#define ADVERTISE_1000_HALF 0x0010
#define ADVERTISE_1000_FULL 0x0020
#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F  /* Everything but 1000-Half */

#endif /* _EM_PHY_H_ */