1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
|
.\" All Rights Reserved, Copyright (C) Fujitsu Limited 1995
.\"
.\" This document may be used, modified, copied, distributed, and sold, in
.\" both source and printed form provided that the above copyright, these
.\" terms and the following disclaimer are retained. The name of the author
.\" and/or the contributor may not be used to endorse or promote products
.\" derived from this software without specific prior written permission.
.\"
.\" THIS DOCUMENT IS PROVIDED BY THE AUTHOR AND THE CONTRIBUTOR ``AS IS'' AND
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
.\" ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR THE CONTRIBUTOR BE LIABLE
.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
.\" OUT OF THE USE OF THIS DOCUMENT, EVEN IF ADVISED OF THE POSSIBILITY OF
.\" SUCH DAMAGE.
.\"
.\" Contributed by M. Sekiguchi <seki@sysrap.cs.fujitsu.co.jp>.
.\" for fe driver.
.\"
.\" $Id: fe.4,v 1.3 1996/03/17 11:44:22 jkh Exp $
.Dd March 3, 1996
.Dt FE 4
.Sh NAME
.Nm fe
.Nd Fujitsu MB86960A/MB86965A based Ethernet adapters
.Sh SYNOPSIS
.Cm "device fe0 at isa? port 0x300 net irq ? vector feintr"
.Sh DESCRIPTION
The
.Nm fe
is a network device driver
for Ethernet adapters based on Fujitsu MB86960A, MB86965A,
or other compatible chips.
.Pp
The driver provides automatic I/O port address configuration and
automatic IRQ configuration,
when used with suitable adapter hardware.
.Pp
The driver works with program I/O data transfer technique.
It gives a fair performance.
Shared memory is never used, even if the adapter has one.
.Pp
It currently works with Fujitsu FMV-180 series for ISA,
Allied-Telesis AT1700 series and RE2000 series for ISA,
and Fujitsu MBH10302 PC card.
.Ss Parameters
On the kernel configuration file, two parameters,
.Ar port
and
.Ar irq ,
must be specified to reflect adapter hardware settings.
Another parameter
.Ar flags
can be specified to provide additional configuration as an option.
Other parameters of the device statement
must appear as described on the synopsis.
.Pp
The
.Ar port
parameter specifies a base I/O port address of the adapter.
It must match with the hardware setting of the adapter.
The
.Ar port
may be a left unspecified as
.Dq Li \&? .
In that case, the driver tries to detect the hardware setting
of the I/O address automatically.
This feature may not work with some adapter hardware.
.Pp
The
.Ar irq
parameter specifies an IRQ number used by the adapter.
It must match the hardware setting of the adapter.
.Ar Irq
may be left unspecified as
.Dq Li \&? ;
in that case, the driver tries to detect
the hardware setting of the IRQ automatically.
This feature may not work on some adapters.
.Pp
The
.Ar flags
is a numeric value which consists of a combination of various device settings.
The following flags are defined in the current version.
To specify two or more settings for a device,
use a numeric sum of each flag value.
Flag bits not specified below are reserved and must be set to 0.
Actually, each bit is either just ignored by the driver,
or tested and used to control undocumented features of the driver.
Consult the source program for undocumented features.
.Bl -tag -width "99999999"
.It Li 0x007F
These flag bits are used
to initialize DLCR6 register of MB86960A/MB86965A chip,
when the
.Li 0x0080
bit of the
.Ar flags
is set.
See below for more about DLCR6 override feature.
The
.Li 0x007F
flag bits must be 0 unless the
.Li 0x0080
bit is set,
to maintain the compatibility with future versions of the driver.
.It Li 0x0080
This flag overrides the default setting to the DLCR6 register
of MB86960A/MB86965A chip by a user supplied value,
which is taken from the lower 7 bits of the flag value.
This is a troubleshooting flag and should not be used
without understanding of the adapter hardware.
Consult the Fujitsu manual for more information
on DLCR6 settings.
.El
.Sh OPTIONS
The
.Nm fe
driver has some private options,
which can be specified with an
.Dq option
statement in the kernel configuration file.
The following lists the private options.
The driver also accepts some other undocumented options,
all of whose names start with a fixed prefix
.Dv "FE_" .
Consult the source program for undocumented options.
.Bl -tag -width "FE_"
.It Dv "FE_DEBUG=" Ns Ar level
This option takes a numeric value
.Ar level
which controls the debugging level for the device and/or the driver.
Setting the
.Dv "FE_DEBUG"
option to a value which is not listed here
may cause undocumented behavior.
The default setting of this option is 1.
.Bl -bullet
.It
Setting
.Dv "FE_DEBUG=0"
makes most of debugging codes,
including sanity check,
be excluded from the object code of the driver.
It generates fastest and smallest object code.
Some emergency messages are logged even under this setting, though.
.It
Setting
.Dv "FE_DEBUG=1"
makes minimum debugging codes be included,
setting the amount of logged messages minimum.
Only fatal error messages are logged under this setting.
.It
Setting
.Dv "FE_DEBUG=2"
makes standard debugging codes be included,
setting the amount of logged messages middle.
Messages on lair events and/or questionable conditions
are logged under this setting.
.It
Setting
.Dv "FE_DEBUG=3"
makes all debugging codes be included,
and set the amount of legged messages maximum.
Redundant messages such as those reporting usual actions
or dumping register values
are logged under this setting.
.El
.El
.Sh FEATURES SPECIFIC TO HARDWARE MODELS
The
.Nm fe
driver has some features and limitations
which depend on adapter hardware models.
The following is a summary of such dependency.
.Ss Fujitsu FMV-180 series adapters
Both automatic IRQ detection and automatic I/O port address detection
is available with these adapters.
.Pp
Automatic I/O port address detection feature of
.Nm fe
works mostly fine for FMV-180 series.
It works even if there are two or more FMV-180s in a system.
However, some combination of other adapters may confuse the driver.
It is recommended not to use
.Nm port ?
when you experience some difficulties with hardware probe.
.Pp
Automatic IRQ detection feature of
.Nm fe
works reliably for FMV-180 series.
It is recommended to use
.Nm irq ?
always for FMV-180.
The hardware setting of IRQ is read
from the configuration EEPROM on the adapter,
even when the kernel config file specifies an IRQ value.
The driver will generate a warning message,
if the IRQ setting specified in the kernel config file
does not match one stored in EEPROM.
Then, it will use the value specified in the config file.
(This behavior has been changed from the previous releases.)
.Ss Allied-Telesis AT1700 series and RE2000 series adapters
Automatic I/O port address detection
is available with Allied-Telesis AT1700 series and RE2000 series,
while it is less reliable than FMV-180 series.
Using the feature with Allied-Telesis adapters
is not recommended.
.Pp
Automatic IRQ detection is also available with some limitation.
The
.Nm fe
driver
tries to get IRQ setting from the configuration EEPROM on the board,
if
.Dq irq \&?
is specified in the configuration file.
Unfortunately,
AT1700 series and RE2000 series seems to have two types of models;
One type allows IRQ selection from 3/4/5/9,
while the other from 10/11/12/15.
Identification of the models are not well known.
Hence, automatic IRQ detection with Allied-Telesis adapters
may not be reliable.
Specify an exact IRQ number if any troubles are encountered.
.Pp
Differences between AT1700 series and RE2000 series
or minor models in those series are not recognized.
.Ss Fujitsu MBH10302 PC card
The
.Nm fe
driver supports Fujitsu MBH10302 and compatible PC cards.
It requires the PC card (PCMCIA) support package.
.Sh SEE ALSO
.Xr netstat 1 ,
.Xr netintro 4 ,
.Xr ed 4 ,
.Xr crd 4 ,
.Xr ifconfig 8 ,
.Xr pccardd 8
.Sh BUGS
Following are major known bugs:
.Pp
Statistics on the number of collisions maintained by the
.Nm fe
driver is not accurate;
the
.Fi i
option of
.Xr netstat 1
shows slightly less value than true number of collisions.
.Pp
More mbuf clusters are used than expected.
The packet receive routine has an intended violation
against the mbuf cluster allocation policy.
The unnecessarily allocated clusters are freed within short lifetime,
and it will not affect long term kernel memory usage.
.Pp
Although XNS and IPX supports are included in the driver,
they are never be tested and must have a lot of bugs.
.Sh AUTHOR, COPYRIGHT AND DISCLAIMER
.Pp
The
.Nm fe
driver was originally written and contributed by M. Sekiguchi
.Li "<seki@sysrap.cs.fujitsu.co.jp>" ,
following the
.Nm ed
driver written by David Greenman.
PC card support in
.Nm fe
is written by Hidetoshi Kimura
.Li "<h-kimura@tokyo.se.fujitsu.co.jp>" .
This manual page was written by M. Sekiguchi.
.Pp
.Em "All Rights Reserved, Copyright (C) Fujitsu Limited 1995"
.Pp
This document and the associated software may be used, modified,
copied, distributed, and sold, in both source and binary form provided
that the above copyright, these terms and the following disclaimer are
retained. The name of the author and/or the contributor may not be
used to endorse or promote products derived from this document and the
associated software without specific prior written permission.
.Pp
THIS DOCUMENT AND THE ASSOCIATED SOFTWARE IS PROVIDED BY THE AUTHOR
AND THE CONTRIBUTOR
.Dq AS IS
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR THE
CONTRIBUTOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
DOCUMENT AND THE ASSOCIATED SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
.Sh HISTORY
The
.Nm
driver appeared in
.Fx 2.0.5 .
|