diff options
Diffstat (limited to 'bin/pax/ar_io.c')
| -rw-r--r-- | bin/pax/ar_io.c | 30 |
1 files changed, 15 insertions, 15 deletions
diff --git a/bin/pax/ar_io.c b/bin/pax/ar_io.c index 69cd48e..e3481bd 100644 --- a/bin/pax/ar_io.c +++ b/bin/pax/ar_io.c @@ -34,7 +34,7 @@ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * - * $Id$ + * $Id: ar_io.c,v 1.2 1994/09/24 02:56:11 davidg Exp $ */ #ifndef lint @@ -278,7 +278,7 @@ ar_open(name) break; default: /* - * should never happen, worse case, slow... + * should never happen, worse case, slow... */ blksz = rdblksz = BLKMULT; break; @@ -458,8 +458,8 @@ ar_set_wr() * will stop us if the archive containing the trailer was not written */ wr_trail = 0; - - /* + + /* * Add any device dependent code as required here */ if (artyp != ISREG) @@ -480,7 +480,7 @@ ar_set_wr() /* * ar_app_ok() * check if the last volume in the archive allows appends. We cannot check - * this until we are ready to write since there is no spec that says all + * this until we are ready to write since there is no spec that says all * volumes in a single archive have to be of the same type... * Return: * 0 if we can append, -1 otherwise. @@ -592,7 +592,7 @@ ar_read(buf, cnt) else warn(0, "End of archive volume %d reached", arvol); return(res); -} +} /* * ar_write() @@ -710,8 +710,8 @@ ar_write(buf, bsz) warn(1,"Unable to append, trailer re-write failed. Quitting."); return(res); } - - if (res == 0) + + if (res == 0) warn(0, "End of archive volume %d reached", arvol); else if (res < 0) syswarn(1, errno, "Failed write to archive volume: %d", arvol); @@ -791,7 +791,7 @@ ar_rdsync() if ((cpos = lseek(arfd, (off_t)0L, SEEK_CUR)) < 0) break; mpos = fsbz - (cpos % (off_t)fsbz); - if (lseek(arfd, mpos, SEEK_CUR) < 0) + if (lseek(arfd, mpos, SEEK_CUR) < 0) break; lstrval = 1; break; @@ -850,14 +850,14 @@ ar_fow(sksz, skipped) * number of physical blocks to skip (we do not know physical block * size at this point), so we must only read foward on tapes! */ - if (artyp != ISREG) + if (artyp != ISREG) return(0); /* * figure out where we are in the archive */ if ((cpos = lseek(arfd, (off_t)0L, SEEK_CUR)) >= 0) { - /* + /* * we can be asked to move farther than there are bytes in this * volume, if so, just go to file end and let normal buf_fill() * deal with the end of file (it will go to next volume by @@ -898,7 +898,7 @@ ar_rev(sksz) { off_t cpos; struct mtop mb; - register int phyblk; + register int phyblk; /* * make sure we do not have try to reverse on a flawed archive @@ -908,7 +908,7 @@ ar_rev(sksz) switch(artyp) { case ISPIPE: - if (sksz <= 0) + if (sksz <= 0) break; /* * cannot go backwards on these critters @@ -1017,7 +1017,7 @@ ar_rev(sksz) /* * get_phys() * Determine the physical block size on a tape drive. We need the physical - * block size so we know how many bytes we skip over when we move with + * block size so we know how many bytes we skip over when we move with * mtio commands. We also make sure we are BEFORE THE TAPE FILEMARK when * return. * This is one really SLOW routine... @@ -1218,7 +1218,7 @@ ar_next() /* * we are to continue with the same device */ - if (ar_open(arcname) >= 0) + if (ar_open(arcname) >= 0) return(0); tty_prnt("Cannot re-open %s, try again\n", arcname); |
