1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
|
# $FreeBSD: src/etc/gettytab,v 1.22 2004/06/06 11:46:27 schweikh Exp $
# from: @(#)gettytab 5.14 (Berkeley) 3/27/91
#
# Most of the table entries here are just copies of the old getty table,
# it is by no means certain, or even likely, that any of them are optimal
# for any purpose whatever. Nor is it likely that more than a couple are
# even correct.
#
# The default gettytab entry, used to set defaults for all other
# entries, and in cases where getty is called with no table name.
#
# cb, ce and ck are desirable on most crt's. The non-crt entries need to
# be changed to turn them off (:cb@:ce@:ck@:).
#
# lc should always be on; it's a remainder of some stone age when there
# have been terminals around not being able of handling lower-case
# characters. Those terminals aren't supported any longer, but getty is
# `smart' about them by default.
#
# Parity defaults to even, but the Pc entry and all the `std' entries
# specify no parity. The different parities are:
# (none): same as ep for getty. login will use terminal as is.
# ep: getty will use raw mode (cs8 -parenb) (unless rw is set) and
# fake parity. login will use even parity (cs7 parenb -parodd).
# op: same as ep except odd parity (cs7 parenb parodd) for login.
# getty will fake odd parity as well.
# ap: same as ep except -inpck instead of inpck for login.
# ap overrides op and ep.
# np: 1. don't fake parity in getty. The fake parity garbles
# characters on non-terminals (like pccons) that don't
# support parity. It would probably better for getty not to
# try to fake parity. It could just use cbreak mode so as
# not to force cs8 and let the hardware handle the parity.
# login has to be rely on the hardware anyway.
# 2. set cs8 -parenb -istrip -inpck.
# ep:op: same as ap.
#
default:\
::cb:ce:ck:lc:fd#1000:im=\r\n%s/%m (%h) (%t)\r\n\r\n:sp#1200:\
:if=/etc/issue:
#
# Fixed speed entries
#
# The "std.NNN" names are known to the special case
# portselector code in getty, however they can
# be assigned to any table desired.
# The "NNN-baud" names are known to the special case
# autobaud code in getty, and likewise can
# be assigned to any table desired (hopefully the same speed).
#
a|std.110|110-baud:\
:np:nd#1:cd#1:uc:sp#110:
b|std.134|134.5-baud:\
:np:nd#1:cd#2:ff#1:td#1:sp#134:ht:nl:
1|std.150|150-baud:\
:np:nd#1:cd#2:td#1:fd#1:sp#150:ht:nl:lm=\E\72\6\6\17login\72 :
c|std.300|300-baud:\
:np:nd#1:cd#1:sp#300:
d|std.600|600-baud:\
:np:nd#1:cd#1:sp#600:
f|std.1200|1200-baud:\
:np:fd#1:sp#1200:
6|std.2400|2400-baud:\
:np:sp#2400:
7|std.4800|4800-baud:\
:np:sp#4800:
2|std.9600|9600-baud:\
:np:sp#9600:
g|std.19200|19200-baud:\
:np:sp#19200:
std.38400|38400-baud:\
:np:sp#38400:
std.57600|57600-baud:\
:np:sp#57600:
std.115200|115200-baud:\
:np:sp#115200:
std.230400|230400-baud:\
:np:sp#230400:
#
# Entry specifying explicit device settings. See termios(4) and
# /usr/include/termios.h, too. The entry forces the tty into
# CLOCAL mode (so no DCD is required), and uses Xon/Xoff flow control.
#
# cflags: CLOCAL | HUPCL | CREAD | CS8
# oflags: OPOST | ONLCR | OXTABS
# iflags: IXOFF | IXON | ICRNL | IGNPAR
# lflags: IEXTEN | ICANON | ISIG | ECHOCTL | ECHO | ECHOK | ECHOE | ECHOKE
#
# The `0' flags don't have input enabled. The `1' flags don't echo.
# (Echoing is done inside getty itself.)
#
local.9600|CLOCAL tty @ 9600 Bd:\
:c0#0x0000c300:c1#0x0000cb00:c2#0x0000cb00:\
:o0#0x00000007:o1#0x00000002:o2#0x00000007:\
:i0#0x00000704:i1#0x00000000:i2#0x00000704:\
:l0#0x000005cf:l1#0x00000000:l2#0x000005cf:\
:sp#9600:
#
# Dial in rotary tables, speed selection via 'break'
#
0|d300|Dial-300:\
:nx=d1200:cd#2:sp#300:
d1200|Dial-1200:\
:nx=d150:fd#1:sp#1200:
d150|Dial-150:\
:nx=d110:lm@:tc=150-baud:
d110|Dial-110:\
:nx=d300:tc=300-baud:
#
# Fast dialup terminals, 2400/1200/300 rotary (can start either way)
#
D2400|d2400|Fast-Dial-2400:\
:nx=D1200:tc=2400-baud:
3|D1200|Fast-Dial-1200:\
:nx=D300:tc=1200-baud:
5|D300|Fast-Dial-300:\
:nx=D2400:tc=300-baud:
#
#telebit (19200)
#
t19200:\
:nx=t2400:tc=19200-baud:
t2400:\
:nx=t1200:tc=2400-baud:
t1200:\
:nx=t19200:tc=1200-baud:
#
#telebit (9600)
#
t9600:\
:nx=t2400a:tc=9600-baud:
t2400a:\
:nx=t1200a:tc=2400-baud:
t1200a:\
:nx=t9600:tc=1200-baud:
#
# Odd special case terminals
#
-|tty33|asr33|Pity the poor user of this beast:\
:tc=110-baud:
4|Console|Console Decwriter II:\
:nd@:cd@:rw:tc=300-baud:
e|Console-1200|Console Decwriter III:\
:fd@:nd@:cd@:rw:tc=1200-baud:
i|Interdata console:\
:uc:sp#0:
l|lsi chess terminal:\
:sp#300:
X|Xwindow|X window system:\
:fd@:nd@:cd@:rw:sp#9600:
P|Pc|Pc console:\
:ht:np:sp#115200:al=root:
#
# Wierdo special case for fast crt's with hardcopy devices
#
8|T9600|CRT with hardcopy:\
:nx=T300:tc=9600-baud:
9|T300|CRT with hardcopy (300):\
:nx=T9600:tc=300-baud:
#
# Plugboard, and misc other terminals
#
plug-9600|Plugboard-9600:\
:pf#1:tc=9600-baud:
p|P9600|Plugboard-9600-rotary:\
:pf#1:nx=P300:tc=9600-baud:
q|P300|Plugboard-300:\
:pf#1:nx=P1200:tc=300-baud:
r|P1200|Plugboard-1200:\
:pf#1:nx=P9600:tc=1200-baud:
#
# XXXX Port selector
#
s|DSW|Port Selector:\
:ps:sp#2400:
#
# Auto-baud speed detect entry for Micom 600.
# Special code in getty will switch this out
# to one of the NNN-baud entries.
#
A|Auto-baud:\
:ab:sp#2400:f0#040:
#
# autologin - automatically log in as root
#
autologin|al.9600:\
:al=root:tc=std.9600:
#
# Entries for 3-wire serial terminals. These don't supply carrier, so
# clocal needs to be set, and crtscts needs to be unset.
#
3wire.9600|9600-3wire:\
:np:nc:sp#9600:
3wire.38400|38400-3wire:\
:np:nc:sp#38400:
3wire.57600|57600-3wire:\
:np:nc:sp#57600:
3wire.115200|115200-3wire:\
:np:nc:sp#115200:
3wire.230400|230400-3wire:\
:np:nc:sp#230400:
|
