diff options
Diffstat (limited to 'usr/local/sbin/mpd.script')
| -rw-r--r-- | usr/local/sbin/mpd.script | 1642 |
1 files changed, 0 insertions, 1642 deletions
diff --git a/usr/local/sbin/mpd.script b/usr/local/sbin/mpd.script deleted file mode 100644 index 28054d7..0000000 --- a/usr/local/sbin/mpd.script +++ /dev/null @@ -1,1642 +0,0 @@ -################################################################# -# -# $Id: mpd.script.sample,v 1.9 2009/10/04 19:36:04 amotin Exp $ -# -# Copyright (c) 1995-1999 Whistle Communications, Inc. All rights reserved. -# See ``COPYRIGHT.whistle'' -# -################################################################# - -## -## MPD Modem script variables: -## -## $DialPrefix Modem dialing prefix (eg. "DT") -## $Telephone Telephone number to dial (not duplicated using &) -## $ConnectTimeout Wait-for-connect timeout, in seconds (default 45 secs) -## $SpeakerOff Set to "yes" to quiet modem speakers -## $Serial230K If "yes", we can support 230K serial port speed -## $CountryCode Country code for Winmodem -## $InitString External initialization string -## $LoginScript If "yes", look for script login -## -## pfSense specific variables: -## $APN Access Point (host)Name for 3G connections -## $APNum Access Point Number, typically "1", might not matter -## $SimPin SIM card PIN number -## $PinWait Wait for SIM to connect to network after PIN entered -## -## ISDN Terminal Adapter specific variables (all start with "TA_"): -## -## $TA_Bonding Bonding on TA: "yes" or "no" -## $TA_NoDoubleTelno When $TA_Bonding, don't double the dialed number -## $TA_56K Restrict to 56K on TA: "yes" or "no" -## $TA_VoiceCall Originate calls using voice mode -## $TA_AuthChap Tell TA to use CHAP: "yes" or "no" -## $TA_Dirno1 TA directory #1 -## $TA_Dirno2 TA directory #2 -## $TA_SPID1 SPID #1 -## $TA_SPID2 SPID #2 -## $TA_SwitchType One of these values -## "NI-1" -## "DMS-100" -## "5ESS P2P" -## "5ESS MP" -## $TA_NewSwitch Means the switch type is new, initiate auto-detect -## (3Com Impact IQ only) -## -## We set $OptimizeNextTime to "yes" after a successful connection so we -## can avoid verifing configuration when things are working good. -## -## Internal variables: -## -## $ModemSetupFunc Routine to set up modem for dialing out -## $ModemAnsSetupFunc Routine to set up modem for answer mode (if different) -## $ModemDetectRing Routine to detect an incoming call for ringback -## $ModemIsAnalog If "yes" modem is analog (ie, not terminal adapter) -## - -################################################################# -# -# MODEM DIALING -# -################################################################# - -DialPeer: - set $CallingID "" - set $CalledID $Telephone - if $Telephone == "00000" goto DialNullModem - set $optimize $OptimizeNextTime - set $OptimizeNextTime "no" - - if $optimize == "yes" goto DialPeer2 - call ModemFind - if $ErrorMsg == "" goto DialPeer1 - log $ErrorMsg - failure -DialPeer1: - set $ModTelephone $Telephone - call ModemIdent - if $ModemDescription != "" goto DialPeer2 - log "No match found in the ModemIdent function in the chat script." - failure - -DialPeer2: - log "Detected $ModemDescription." - call $ModemSetupFunc - log "Dialing server at $Telephone..." - call ModemDial - if $dialResult == "OK" goto DialPeerOK - set $optimize "no" - failure - -DialPeerOK: - if $ConnectionSpeed == "" log "Connected at an unknown speed." - if $ConnectionSpeed == "" goto DialPeer3 - log "Connected at $ConnectionSpeed." -DialPeer3: - if $LoginScript == "yes" call AutoLogin - set $OptimizeNextTime "yes" - success - -DialPeerSetPin: - set $modemCmd "+CPIN?" - log $modemCmd - call ModemQuery - log $modemQuery - if $modemQuery match ".*READY.*" goto DialPinReady - set $modemCmd "+CPIN=\"$SimPin\"" - call ModemCmd2 - wait $PinWait - -DialPinReady: - return - -DialPeerSetAPN: - set $modemCmd "+CGDCONT=$APNum,\"IP\",\"$APN\"" - log $modemCmd - call ModemCmd2 - return - -# Null-modem connection -DialNullModem: - log "Connected via null modem connection." - success - -## -## Dial modem -## -## Variables: -## -## $DialPrefix Modem dialing prefix (eg. "DT") -## $ModTelephone Telephone number to dial -## $ConnectTimeout Wait-for-connect timeout, in seconds (default 45 secs) -## $noDialToneSubr (optional) Subroutine to call if NO DIALTONE -## $dialErrorSubr (optional) Subroutine to call if ERR -## -## Returns: -## -## $dialResult "OK" or "FAIL" -## $ConnectionSpeed Connection speed reported by modem (possibly empty) -## - -ModemDial: - set $dialResult "FAIL" - set $ConnectionSpeed "" - if $ConnectTimeout == "" set $ConnectTimeout 45 - print "AT${DialPrefix}${ModTelephone}\r\n" - log "AT${DialPrefix}${ModTelephone}" - match "NO CARRIER" DialAbortNoCar - match "NO DIAL" DialAbortNoDial - match "BUSY" DialAbortBusy - regex "CONNECT *([0-9]*).*$" DialConnect - match "ERR" DialError - wait $ConnectTimeout - log "No response from the modem after dialing." - return -DialAbortNoCar: - log "The remote modem did not answer." - return -DialAbortNoDial: - if $noDialToneSubr != "" goto $noDialToneSubr - log "No dialtone. Is the modem plugged in?" - return -DialError: - if ${ModTelephone} != "" goto DialErrorInit - log "Invalid empty telephone number." - return -DialErrorInit: - if $dialErrorSubr != "" goto $dialErrorSubr - log "Invalid dial init string." - return -DialAbortBusy: - log "The line was busy." - return -DialConnect: - set $ConnectionSpeed $matchedString1 - set $dialResult "OK" - return - -################################################################# -# -# MODEM ANSWERING -# -################################################################# - -## -## This is an idle script that waits for an incoming call and answers it -## -## Variables: -## -## $RingTimeout How long to wait for a RING before giving up -## $ConnectTimeout Wait-for-connect timeout, in seconds (default 45 secs) -## - -AnswerCall: - set $CallingID "" - set $CalledID "" - set $optimize $OptimizeNextTime - set $OptimizeNextTime "no" - -# Skip modem detection if we connected successfully last time - - if $optimize == "yes" goto AnswerCall2 - call ModemFind - if $ErrorMsg == "" goto AnswerCall0 - log $ErrorMsg - failure -AnswerCall0: - call ModemIdent - if $ModemDescription != "" goto AnswerCall1 - log "The modem is not responding." - failure -AnswerCall1: - log "Detected $ModemDescription." - -AnswerCall2: - if $ModemAnsSetupFunc == "" set $ModemAnsSetupFunc $ModemSetupFunc - call $ModemAnsSetupFunc - log "Waiting for ring..." - call ModemAnswer - if $answerReturn == "OK" goto AnswerCallOK - set $IdleResult "" - set $optimize "no" - failure - -AnswerCallOK: - log "Connected at $ConnectionSpeed." - set $OptimizeNextTime "yes" - set $IdleResult "answer" - success - -################################################################# -# -# MODEM RINGBACK -# -################################################################# - -## -## This is an idle script that implements the ringback feature. -## When we're idle, and we detect an incoming call, then call back -## to bring up the link. For analog modems, we have to wait until -## the ringing stops before dialing back (otherwise we'd answer the -## call, which we don't want to do). -## -## Variables: -## -## $RingbackTimeout How long before giving up (reset and try again). -## Default: 60 minutes -## $RingStoppedTime Max time between consecutive "RING"s (if analog) -## Default: 8 seconds -## - -Ringback: - set $CallingID "" - set $CalledID "" - if $RingbackTimeout == "" set $RingbackTimeout "3600" - if $RingStoppedTime == "" set $RingStoppedTime "8" - set $ModemDetectRing RingbackWait - call ModemFind - if $ErrorMsg == "" goto Ringback1 - log $ErrorMsg - failure -Ringback1: - call ModemIdent - if $ModemDescription != "" goto Ringback2 - log "The modem is not responding." - failure - -Ringback2: - log "Detected $ModemDescription." - goto $ModemDetectRing - -# Detect an incoming call by waiting for a "RING" indication -# On an analog modem, we have to wait for the ringing to stop - -RingbackWait: - match "RING\r\n" RingbackGotRings - log "Remote Dial-Back mode enabled; waiting for incoming call." - wait $RingbackTimeout - failure - -# We saw it ring; wait for the ringing to stop (analog modems only). - -RingbackGotRings: - log "Incoming call detected..." - if $ModemIsAnalog != "yes" goto RingbackDone -RingbackWaitStop: - match "RING\r\n" RingbackWaitStop - wait $RingStoppedTime -RingbackDone: - set $IdleResult "ringback" - success - -# Strip leading and trailing spaces and log calling party number - -RingbackDetectCID: - if $cid match " *(.*) *" nop - set $cid $matchedString1 - if $cid == "" goto RingbackDetectNoCID - log "Incoming call detected from $cid..." - success - -# We couldn't determine calling party number - -RingbackDetectNoCID: - log "Incoming call detected..." - success - -################################################################# -# -# MODEM IDENTIFICATION -# -################################################################# - -## -## Identify -## -## This is meant to be called from the top level, to just identify -## what's on the serial port and print out some info about it. -## - -Identify: - call ModemFind - if $ErrorMsg == "" goto Identify1 - failure -Identify1: - call ModemIdent - if $ModemDescription == "" failure - log "ANALOG=$ModemIsAnalog" - log "DESCRIPTION=$ModemDescription" - success - -## -## ModemIdent -## -## This identifies the type of modem and sets these variables accordingly: -## -## $ModemDescription -## $ModemSetupFunc -## $ModemAnsSetupFunc -## $ModemDetectRing -## $ModemIsAnalog -## -## If no response seen, this sets $ModemDescription to the empty string. -## - -ModemIdent: - set $ModemDescription "" - set $ModemSetupFunc "" - set $ModemAnsSetupFunc "" - set $ModemDetectRing "" - set $ModemIsAnalog "yes" - if $InitString != "" goto ModemIdentCustom - print "ATI\r\n" - match "ADTRAN EXPRESS XR" ModemIdentAdtranXRT - match "Model: Ovation MC950D Card" ModemIdentMC950D - match "ERR" ModemIdentGeneric - match "OK\r\n" ModemIdentGeneric - wait 3 - print "ATI1\r\n" - match "NTK omni.net" ModemIdentNTK - match "ERR" ModemIdentGeneric - match "OK\r\n" ModemIdentGeneric - wait 3 - print "ATI3\r\n" - match "Courier" ModemIdentUsr - match "Sportster" ModemIdentUsr - match "3ComImpact IQ" ModemIdentImpactIQ - match "U.S. Robotics 56K" ModemIdentUsr - match "ZOOM V.90" ModemIdentZoom56 - match "LT V.90" ModemIdentLucent - match "ERR" - match "OK\r\n" - wait 3 - print "ATI4\r\n" - match "AtermIT NEC Corporation" ModemIdentAterm - match "INSMATEV-7 NTT Corporation" ModemIdentAterm - match "MNP Class 10 V.34 Modem" ModemIdentDeskPorte - match "Smart One 56" ModemIdentSmartOne - match "ERR" - match "OK\r\n" - wait 3 - print "ATI5\r\n" - match "C885" ModemIdentC885 - match "ERR" - match "OK\r\n" ModemIdentGeneric - wait 3 - print "ATI8\r\n" - match "BitSURFR PRO\r" ModemIdentBitsurfr - match "BitSURFR PRO EZ" ModemIdentBitsurfrEZ - match "3C882" ModemIdentImpactIQ - match "ERR" - match "OK\r\n" - wait 3 - log "The modem is not responding to any ATI[1,3-5,8] commands." - failure - -ModemIdentGeneric: - set $ModemDescription "Hayes compatible modem" - if $SimPin != "" call DialPeerSetPin - if $APN != "" call DialPeerSetAPN - set $ModemSetupFunc GenericSetup - return - -ModemIdentCustom: - set $ModemDescription "Custom modem" - set $ModemSetupFunc CustomSetup - return - -ModemIdentUsr: - set $SportsterHack "no" - if $matchedString == "Sportster" set $SportsterHack "yes" - set $ModemDescription "USR $matchedString modem" - call GetOK - set $ModemSetupFunc UsrSetup - return -ModemIdentC885: - set $ModemDescription "Sierra Wireless Compass $matchedString USB 3G modem" - set $ModemSetupFunc GenericSetup - return -ModemIdentMC950D: - set $ModemDescription "Novatel Wireless $matchedString USB 3G modem" - set $ModemSetupFunc GenericSetup - return -ModemIdentBitsurfrEZ: - set $bitsEZ "yes" -ModemIdentBitsurfr: - set $ModemDescription "Motorola $matchedString" - call GetOK - set $ModemSetupFunc BitsurfrSetup - set $ModemIsAnalog "no" - set $ModemDetectRing BitsurfrDetectRing - return - -ModemIdentImpactIQ: - set $matchedString "3ComImpact IQ" - set $ModemDescription "$matchedString" - call GetOK - set $ModemSetupFunc ImpactIQSetup - set $ModemIsAnalog "no" - set $ModemDetectRing ImpactIQDetectRing - return - -ModemIdentAdtranXRT: - set $ModemDescription "AdTran Express XR/XRT" - call GetOK - set $ModemSetupFunc AdtranXRTSetup - set $ModemIsAnalog "no" - return - -ModemIdentAterm: - set $ModemDescription "NEC Aterm TA" - call GetOK - set $ModemSetupFunc AtermSetup - set $ModemIsAnalog "no" - return - -ModemIdentNTK: - set $ModemDescription "$matchedString" - call GetOK - set $ModemSetupFunc NTKSetup - set $ModemIsAnalog "no" - return - -ModemIdentDeskPorte: - set $ModemDescription "$matchedString" - call GetOK - set $ModemSetupFunc DeskPorteSetup - return - -ModemIdentZoom56: -ModemIdentSmartOne: - set $ModemDescription "$matchedString" - call GetOK - set $ModemSetupFunc Modem56Setup - return - -# Support the Lucent Winmodem, Xircom 56k -ModemIdentLucent: - set $ModemDescription "$matchedString" - call GetOK - set $ModemSetupFunc ModemLucentSetup - return - -################################################################# -# -# GENERIC MODEM SETUP -# -################################################################# - -GenericSetup: - set $noDialToneSubr GenericNoDialtone - set $temp "M1" - if $SpeakerOff == "yes" set $temp "M0" - set $modemCmd "&F&C1&D2E0S0=0${temp}" - call ModemCmd2 - return - -CustomSetup: - set $noDialToneSubr GenericNoDialtone - set $modemCmd "${InitString}" - call ModemCmd2 - return - -GenericNoDialtone: - log "No dialtone. Is the modem plugged in?" - return - -################################################################# -# -# USR MODEM SETUP -# -################################################################# - -UsrSetup: -# Lower baudrate to 57600 for crappy internal Sportster modem - if $SportsterHack != "yes" goto UsrSetup2 - if $modemDevice != "/dev/cuad2" goto UsrSetup2 - set $Baudrate 57600 - set $modemCmd "" - call ModemCmd2 -UsrSetup2: - set $noDialToneSubr GenericNoDialtone - set $temp "M1" - if $SpeakerOff == "yes" set $temp "M0" - set $modemCmd "&F1&C1&D2E0S0=0S13.0=1L0S6=5${temp}" - call ModemCmd2 - return - -################################################################# -# -# GENERAL 56K MODEM SETUP -# -################################################################# - -Modem56Setup: - set $noDialToneSubr GenericNoDialtone - set $temp "M1" - if $SpeakerOff == "yes" set $temp "M0" - set $modemCmd "&FL2W2E0${temp}" - call ModemCmd2 - return - -################################################################# -# -# LUCENT WINMODEM AND XIRCOM 56K SETUP -# -################################################################# - -ModemLucentSetup: - set $noDialToneSubr GenericNoDialtone - set $temp "M1" - if $SpeakerOff == "yes" set $temp "M0" - set $tempCountryCode "" - if $CountryCode != "" set $tempCountryCode "+GCI=${CountryCode}" - if $CountryCode != "" log "Use country ${CountryCode}" - set $modemCmd "&FL2W2E0${temp}${tempCountryCode}" - call ModemCmd2 - return - -################################################################# -# -# BITSURFR PRO AND BITSURFR PRO EZ SETUP -# -################################################################# - -BitsurfrSetup: - set $noDialToneSubr BitsurfrNoDialtone - set $factory "1" - if $bitsEZ == "yes" set $factory "0" - set $modemCmd "Z&F${factory}&C1&D2E0W1X2%A2=95S0=0" - call ModemCmd2 - -# Set to 230K baud if we support it - - if $bitsEZ != "yes" goto BitsurfrSetup1 - set $modemCmd "@P2=230400" - set $newBaudrate "230400" - call SetBaudrate - -# Check software revision and ISDN settings - -BitsurfrSetup1: - if $optimize == "yes" goto BitsurfrSetup2 - if $bitsEZ != "yes" call BitsurfrCheckRev - call BitsurfrCheckConfig - -# Set the PAP/CHAP, multi-link, and 56K/64K settings, and return - -BitsurfrSetup2: - set $authCmd "@M2=P" - if $TA_AuthChap == "yes" set $authCmd "@M2=C" - set $bondCmd "@B0=1" - if $TA_Bonding == "yes" set $bondCmd "@B0=2" - set $bearCmd "%A4=0" - if $TA_56K == "yes" set $bearCmd "%A4=1" - if $TA_VoiceCall == "yes" set $bearCmd "%A4=1" - set $voiceCmd "%A98=D%A96=0" - if $TA_VoiceCall == "yes" set $voiceCmd "%A98=S%A96=1" - -# BS PRO EZ changes - - if $bitsEZ == "yes" set $authCmd "${authCmd}@M20=\"\"" - set $modemCmd "$authCmd$bondCmd$bearCmd$voiceCmd" - call ModemCmd2 - if $TA_NoDoubleTelno == "yes" return - if $TA_Bonding == "yes" set $ModTelephone "${Telephone}&${Telephone}" - return - -## -## What to do when NO DIALTONE -## - -BitsurfrNoDialtone: - log "ISDN initialization failed (or BitSURFR restarting). Please verify proper line connection and ISDN settings." - return - -## -## BitsurfrCheckConfig -## -## Verify and adjust ISDN configuration as necessary -## - -BitsurfrCheckConfig: - log "Checking the BitSURFR's ISDN configuration..." - set $valueChanged "no" - -# Check switch type - - set $checkCmd "!C0" - set $checkValue "000" - set $checkValueNew "0" - if $TA_SwitchType == "DMS-100" set $checkValue "001" - if $TA_SwitchType == "DMS-100" set $checkValueNew "1" - if $TA_SwitchType == "NI-1" set $checkValue "002" - if $TA_SwitchType == "NI-1" set $checkValueNew "2" - set $checkMsg "Reprogramming switch type ($TA_SwitchType)..." - call ModemCheckValue - - set $checkCmd "!C1" - set $checkValue "004" - set $checkValueNew "4" - if $TA_SwitchType == "DMS-100" set $checkValue "003" - if $TA_SwitchType == "DMS-100" set $checkValueNew "3" - if $TA_SwitchType == "5ESS P2P" set $checkValue "000" - if $TA_SwitchType == "5ESS P2P" set $checkValueNew "0" - if $TA_SwitchType == "5ESS MP" set $checkValue "001" - if $TA_SwitchType == "5ESS MP" set $checkValueNew "1" - set $checkMsg "Reprogramming switch software version..." - call ModemCheckValue - -# Check directory numbers - - set $checkCmd "*1!N1" - set $checkValue $TA_Dirno1 - set $checkValueNew $TA_Dirno1 - set $checkMsg "Reprogramming voice line #1 directory number..." - call ModemCheckValue - - set $checkCmd "*2!N1" - set $checkValue $TA_Dirno2 - set $checkValueNew $TA_Dirno2 - set $checkMsg "Reprogramming voice line #2 directory number..." - call ModemCheckValue - set $checkCmd "!N1" - set $checkMsg "Reprogramming data line directory number..." - call ModemCheckValue - -# Check SPIDs - - set $checkCmd "*1!C6" - set $checkValue $TA_SPID1 - set $checkValueNew $TA_SPID1 - set $checkMsg "Reprogramming voice line #1 SPID..." - call ModemCheckValue - - set $checkCmd "*2!C6" - set $checkValue $TA_SPID2 - set $checkValueNew $TA_SPID2 - set $checkMsg "Reprogramming voice line #2 SPID..." - call ModemCheckValue - set $checkCmd "!C6" - set $checkMsg "Reprogramming data line SPID..." - call ModemCheckValue - -# Restart if necessary - - if $valueChanged == "no" return - log "Restarting BitSURFR Pro with new configuration..." - set $modemCmd ">W" - call ModemCmd2 - set $modemCmd ">Z" - call ModemCmd2 - failure - -## -## Verify the BitSURFR's software revision. Only do this -## once, the first time we try to dial. -## - -BitsurfrCheckRev: - log "Checking the BitSURFR's software revision..." - print "ATI3\r\n" - match "-1A" BitsurfrCheckRevOld - match "-1B" BitsurfrCheckRevOld - match "-1C" BitsurfrCheckRevOld - match "-1D" BitsurfrCheckRevOld - match "-1E" BitsurfrCheckRevOld - match "-1F" BitsurfrCheckRevOld - match "-1G" BitsurfrCheckRevOld - match "-1H" BitsurfrCheckRevOld - match "-1I" BitsurfrCheckRevOld - match "OK\r\n" BitsurfrCheckRevOK - match "ERR" - wait 5 - log "The BitSURFR did not properly answer ATI3." - failure -BitsurfrCheckRevOK: - return -BitsurfrCheckRevOld: - log "The BitSURFR Pro has an old software revision $matchedString. Please upgrade according to the manufacturer's instructions." - call GetOK - failure - -# This is how we detect an incoming call with a BitSURFR - -BitsurfrDetectRing: -# First, we need to be properly configured - call BitsurfrSetup -# Enable Caller-ID logging - set $modemCmd "@N0=1*1@N0=1*2@N0=1" - call ModemCmd - if $modemCmdResult != "OK" goto RingbackWait -# A "RING" at any time is good enough - match ringset "RING\r\n" RingbackDone -# Clear Caller-ID buffers - set $modemCmd "@L0*1@L0*2@L0" - call ModemCmd2 -# Read each buffer - call BitsurfrDetectReadCID - log "Remote Dial-Back mode enabled; waiting for incoming call." -# Now wait indefinitely for one of those buffers to change -BitsurfrDetectLoop: - wait 5 - set $oldDataCID $dataCID - set $oldVoice1CID $voice1CID - set $oldVoice2CID $voice2CID - call BitsurfrDetectReadCID - if $oldDataCID != $dataCID goto BitsurfrDetectDone - if $oldVoice1CID != $voice1CID goto BitsurfrDetectDone - if $oldVoice2CID != $voice2CID goto BitsurfrDetectDone - goto BitsurfrDetectLoop - -# Examine the CID from each port -BitsurfrDetectDone: - set $cid $dataCID - call BitsurfrDetectTryCID - set $cid $voice1CID - call BitsurfrDetectTryCID - set $cid $voice2CID - call BitsurfrDetectTryCID - goto RingbackDetectNoCID - -# Try to extract the calling party number -BitsurfrDetectTryCID: -# Strip the log number - if $cid match "[0-9] (.*)" set $cid $matchedString1 -# Check for various strings - if $cid match "BLOCKED" return - if $cid match "NO NUMBER" return - if $cid match "NO CID SERVICE" return - if $cid match "OUT OF AREA" return - goto RingbackDetectCID - -# Read Caller-ID buffers -BitsurfrDetectReadCID: - set $modemCmd "@L1" - call ModemQueryStrip - set $dataCID $modemQuery - set $modemCmd "*1@L1" - call ModemQueryStrip - set $voice1CID $modemQuery - set $modemCmd "*2@L1" - call ModemQueryStrip - set $voice2CID $modemQuery - return - -################################################################# -# -# 3COM IMPACT IQ SETUP -# -################################################################# - -ImpactIQSetup: - set $noDialToneSubr ImpactIQNoDialtone - set $modemCmd "Z&F%C2E0" - call ModemCmd2 - -# Set to 230K baud if we support it - - set $modemCmd "$$B230400" - set $newBaudrate "230400" - call SetBaudrate - -# Check ISDN config and link status (XXX should we check revision too?) - -ImpactIQSetup1: - if $optimize == "yes" goto IQInitSetup2 - call ImpactIQCheckConfig - call ImpactIQCheckLink - -# Now set the PAP/CHAP setting and voice/data originate mode setting - -IQInitSetup2: - set $authCmd "S84=1" - if $TA_AuthChap == "yes" set $authCmd "S84=0" - set $voiceCmd "S61=0" - if $TA_VoiceCall == "yes" set $voiceCmd "S61=1" - set $modemCmd "$authCmd$voiceCmd" - call ModemCmd2 - if $TA_NoDoubleTelno == "yes" return - if $TA_Bonding == "yes" set $ModTelephone "${Telephone}&${Telephone}" - return - -## -## What to do when NO DIALTONE -## - -ImpactIQNoDialtone: - log "ISDN config problem (or modem restart). Check your ISDN switch type, directory numbers, and SPID settings." - return - -## -## ImpactIQCheckLink -## -## Check the link status registers -## - -ImpactIQCheckLink: - log "Checking the ISDN modem's link status..." - print "ATS59?\r\n" - match "000" IQSyncFail - match "001" IQSyncOK - match "ERR" - match "OK\r\n" - wait 3 - call GetOK - log "The ISDN modem did not properly answer ATS59?" - failure -IQSyncOK: - call GetOK - goto ImpactIQCheckInit -IQSyncFail: - log "The ISDN modem is not receiving any ISDN signal. Please verify that it's connected to an ISDN line." - call GetOK - failure - -ImpactIQCheckInit: - set $impactInitReg "57" - call IQInitCheck - if $TA_Bonding == "yes" return - set $impactInitReg "58" - call IQInitCheck - return - -# A little subroutine - -IQInitCheck: - print "ATS${impactInitReg}?\r\n" - match "000" IQInitOK - match "001" IQInitOK - match "002" IQInitFail - match "ERR" - match "OK\r\n" - wait 3 - call GetOK - log "The ISDN modem did not properly answer ATS${impactInitReg}?" - failure -IQInitOK: - call GetOK - return -IQInitFail: - log "ISDN initialization failed. Please check your ISDN switch type, directory numbers, and SPID settings." - call GetOK - failure - -## -## ImpactIQCheckConfig -## -## Verify and adjust ISDN configuration as necessary -## - -ImpactIQCheckConfig: - log "Checking the ISDN modem's ISDN configuration..." - set $valueChanged "no" - -# Check switch type XXX -# -# NOTE: The Impact IQ changes the value of this field as it auto-detects. -# Not only that, but it cycles through each switch type as it is "trying -# out" that type, so that reading this field is pretty much useless... -# Our strategy is just to hope that auto-detect works! - - if $TA_NewSwitch != "yes" goto ImpactIQCheckDirnos - log "Initiating switch type auto-detect..." - set $modemCmd "S50=0" - call ModemCmd2 - set $TA_NewSwitch "" - set $valueChanged "yes" - set $iq_new_switch "yes" - -# Check directory numbers - -ImpactIQCheckDirnos: - set $checkCmd "S51" - set $checkValue $TA_Dirno1 - set $checkValueNew $TA_Dirno1 - set $checkMsg "Reprogramming line #1 directory number..." - call ModemCheckValue - - set $checkCmd "S53" - set $checkValue $TA_Dirno2 - set $checkValueNew $TA_Dirno2 - set $checkMsg "Reprogramming line #2 directory number..." - call ModemCheckValue - -# Check SPIDs - - set $checkCmd "S52" - set $checkValue $TA_SPID1 - set $checkValueNew $TA_SPID1 - set $checkMsg "Reprogramming line #1 SPID..." - call ModemCheckValue - - set $checkCmd "S54" - set $checkValue $TA_SPID2 - set $checkValueNew $TA_SPID2 - set $checkMsg "Reprogramming line #2 SPID..." - call ModemCheckValue - -# Check 56K/64K setting - - set $checkValue "064" - set $checkValueNew "64" - if $TA_56K == "yes" set $checkValue "056" - if $TA_56K == "yes" set $checkValueNew "56" - set $checkCmd "S60" - set $checkMsg "Reprogramming B channel data rate to ${checkValueNew}K..." - call ModemCheckValue - set $checkValueNew "" - -# Check Multi-link setting - - set $checkValue "000" - set $checkValueNew "0" - if $TA_Bonding == "yes" set $checkValue "001" - if $TA_Bonding == "yes" set $checkValueNew "1" - set $checkCmd "S80" - set $checkMsg "Reprogramming mutli-link PPP setting..." - call ModemCheckValue - -# Restart if necessary, and wait extra long if the switch type changed - - if $valueChanged == "no" return - log "Restarting ISDN modem with the new configuration..." - set $modemCmd "Z" - call ModemCmd2 - failure - -## -## Detect an incoming call with the 3Com -## - -ImpactIQDetectRing: - call ImpactIQSetup - if $modemCmdResult != "OK" goto RingbackWait - match ringset "RING\r\n" RingbackDone -# Clear Caller-ID buffers - set $modemCmd "\\N0" -# We don't care if this command fails... - call ModemCmd -# Read most recent incoming call - call ImpactIQDetectReadCID - log "Remote Dial-Back mode enabled; waiting for incoming call." -# Now wait for a change -ImpactIQDetectLoop: - wait 5 - set $oldIncomingCall $incomingCall - call ImpactIQDetectReadCID - if $oldIncomingCall != $incomingCall goto ImpactIQDetectDone - goto ImpactIQDetectLoop - -# Examine the CID from each port -ImpactIQDetectDone: - if $incomingCall !match "((.{14}).{10}) ((.{14}).{10}) ((.{14}).{10})" goto RingbackDetectNoCID - set $dataCID $matchedString2 - set $voice1CID $matchedString4 - set $voice2CID $matchedString6 - set $cid $dataCID - call ImpactIQDetectTryCID - set $cid $voice1CID - call ImpactIQDetectTryCID - set $cid $voice2CID - call ImpactIQDetectTryCID - goto RingbackDetectNoCID - -# Look for a valid CID string -ImpactIQDetectTryCID: - if $cid match " *" return - if $cid match " *N/A" return - goto RingbackDetectCID - -# Read first line of incoming call log (it's the 14th line of output) -ImpactIQDetectReadCID: - set $modemCmd "\\N" - call ModemCmdSend - call ReadLine -# Older version of the 3Com don't support this command - if $matchedString == "OK" return - if $matchedString match "ERR(O)?(R)?" return - call ReadLine - call ReadLine - call ReadLine - call ReadLine - call ReadLine - call ReadLine - call ReadLine - call ReadLine - call ReadLine - call ReadLine - call ReadLine - call ReadLine - call ReadLine - set $incomingCall $matchedString - call GetOK - return - -################################################################# -# -# NEC ATERM SETUP -# -################################################################# - -AtermSetup: - if $AtermHardReset == "yes" goto AtermSetup2 - -# Do hardware reset, which takes a while and doesn't give back "OK" - - log "Initializing modem..." - print "ATZ98\r\n" - wait 6 - set $AtermHardReset "yes" - failure - -AtermSetup2: - -# Set to 230K baud if we support it - - set $modemCmd "" - set $newBaudrate "230400" - call SetBaudrate - -# Is this an IT55 or IT65? - - set $atermIT65 "" - set $modemCmd "$$N14=0" - call ModemCmd - if $modemCmdResult == "OK" set $atermIT65 "yes" - -# Set normal stuff, PPP mode - - set $modemCmd "&C1&D0&K3X4$$N1=1$$N9=0" - call ModemCmd2 - -# Set the multi-link setting - - set $bondCmd "$$N11=0" - if $TA_Bonding == "yes" set $bondCmd "$$N11=1" - set $modemCmd "$bondCmd" - call ModemCmd2 - -# Additional settings for the IT65 go here... - - if $atermIT65 != "yes" return - return - -################################################################# -# -# MICROCOM DESKPORTE SETUP -# -################################################################# - -DeskPorteSetup: - set $noDialToneSubr GenericNoDialtone - set $temp "M1" - if $SpeakerOff == "yes" set $temp "M0" - set $modemCmd "Z&F&C1&D2X3E0S0=0${temp}" - call ModemCmd2 - return - -################################################################# -# -# KOREAN TERMINAL ADAPTER SETUP -# -################################################################# - -NTKSetup: - set $noDialToneSubr GenericNoDialtone - set $modemCmd "ZB40&J3" - call ModemCmd2 - return - -################################################################# -# -# ADTRAN EXPRESS XRT SETUP -# -################################################################# - -AdtranXRTSetup: - set $noDialToneSubr ImpactIQNoDialtone - set $dialErrorSubr AdtranXRTDialError - set $bonding "&F1" - if $TA_Bonding == "yes" set $bonding "&F2" - set $chap "S118=0" - if $TA_AuthChap == "yes" set $chap "S118=32" - set $origCmd "S53=3" - if $TA_56K == "yes" set $origCmd "S53=2" - if $TA_VoiceCall == "yes" set $origCmd "S53=0" - set $modemCmd "ZE0${bonding}&C1&D2${chap}${origCmd}" - call ModemCmd2 - -# Check ISDN config and link status (XXX should we check revision too?) - - if $optimize == "yes" return - call AdtranXRTCheckConfig - call AdtranXRTCheckLink - return - -## -## What to do when ERROR when dialing -## -## This is what the Adtran returns if the line is not ready yet. -## So we look into the status buffer to see if we recognize the -## error condition. -## - -AdtranXRTDialError: - call AdtranXRTDiagnose - failure - -## -## Check the last status bufffer entry for what the problem is -## XXX Figure out more stuff to look for and when it can happen -## - -AdtranXRTDiagnose: - log "Checking the Adtran status buffer..." - print "AT!S\r\n" - match "\r\n\r\n" AdtranXRTDiagBlank - match "END OF STATUS BUFFER" AdtranXRTDiagBlank - match "L1 not up." AdtranXRTDiagL1 - match "FACILITY_NOT_SUBSCRIBED" AdtranXRTDiagFNS - match "Unknown AT cmd" IQSyncOK - match "ERR" - match "OK\r\n" - wait 3 - call GetOK - log "The ISDN modem did not properly answer ATS59?" - failure - goto ImpactIQCheckInit - -AdtranXRTDiagFNS: - log "ISDN initialization failed. Please check your ISDN switch type, directory numbers, and SPID settings." - failure - -AdtranXRTDiagL1: - log "The ISDN modem is not receiving any ISDN signal. Please verify that it's connected to an ISDN line." - failure - -AdtranXRTDiagBlank: - log "ISDN initialization failed or restarting link. Please verify proper line connection and ISDN settings." - failure - -## -## AdtranXRTCheckLink -## -## Check the link status registers -## - -AdtranXRTCheckLink: - log "Checking the ISDN modem's link status..." - print "AT!S1\r\n" - match "Link In Sync" AdtranXRTSyncReg - match "Getting" AdtranXRTSyncReg - match "Register" AdtranXRTSyncReg - match "Ready" AdtranXRTSyncOK - match "Down" AdtranXRTSyncFail - match "ERR" - match "OK\r\n" - wait 3 - call GetOK - log "The ISDN modem did not properly answer AT!S1." - failure -AdtranXRTSyncOK: - return -AdtranXRTSyncFail: - print "ATDT1\r\n" - wait 1 - goto AdtranXRTDiagnose -AdtranXRTSyncReg: - log "The ISDN modem is initializing itself." - failure - -## -## AdtranXRTCheckConfig -## -## Verify and adjust ISDN configuration as necessary -## - -AdtranXRTCheckConfig: - log "Checking the ISDN modem's ISDN configuration..." - set $valueChanged "no" - - set $checkCmd "S52" - set $checkValue "000" - set $checkValueNew "0" - if $TA_SwitchType == "DMS-100" set $checkValue "001" - if $TA_SwitchType == "DMS-100" set $checkValueNew "1" - if $TA_SwitchType == "NI-1" set $checkValue "002" - if $TA_SwitchType == "NI-1" set $checkValueNew "2" - set $checkMsg "Reprogramming switch type ($TA_SwitchType)..." - call ModemCheckValue - -# Check directory numbers - -AdtranXRTCheckDirnos: - set $checkCmd "SS62" - set $checkValue $TA_Dirno1 - set $checkValueNew $TA_Dirno1 - set $checkMsg "Reprogramming line #1 directory number..." - call ModemCheckValue - - set $checkCmd "SS63" - set $checkValue $TA_Dirno2 - set $checkValueNew $TA_Dirno2 - set $checkMsg "Reprogramming line #2 directory number..." - call ModemCheckValue - -# Check SPIDs - - set $checkCmd "SS60" - set $checkValue $TA_SPID1 - set $checkValueNew $TA_SPID1 - set $checkMsg "Reprogramming line #1 SPID..." - call ModemCheckValue - - set $checkCmd "SS61" - set $checkValue $TA_SPID2 - set $checkValueNew $TA_SPID2 - set $checkMsg "Reprogramming line #2 SPID..." - call ModemCheckValue - -# Restart if necessary - - if $valueChanged == "no" return - log "Restarting ISDN modem with the new configuration..." - set $modemCmd "&W" - call ModemCmd2 - set $modemCmd "Z" - call ModemCmd2 - failure - -################################################################# -# -# BASIC MODEM STUFF -# -################################################################# - -## -## ModemAnswer -## -## Wait for a RING and answer it. Variables: -## -## $RingTimeout How long for a RING before giving up (default 10 min) -## $ConnectTimeout How long for connect after answering (default 45 secs) -## -## Returns: -## -## $answerReturn "OK" or "FAIL" -## $ConnectionSpeed Connection speed reported by modem (possibly empty) -## - -ModemAnswer: - if $RingTimeout == "" set $RingTimeout 600 - if $ConnectTimeout == "" set $ConnectTimeout 45 - match "RING\r" ModemAnswerGotRing - wait $RingTimeout - log "No RING detected after $RingTimeout seconds." - set $answerReturn "FAIL" - return -ModemAnswerGotRing: - log "Incoming call detected..." - print "ATA\r\n" - regex "CONNECT *([0-9]*).*$" ModemAnswerConnect - wait $ConnectTimeout - log "Failed to connect incoming call." - set $answerReturn "FAIL" - return -ModemAnswerConnect: - set $ConnectionSpeed $matchedString1 - set $answerReturn "OK" - return - -## -## ModemFind -## -## Just try to get where we are talking to the modem. -## Returns with $ErrorMsg equal to the empty string if -## we found the modem, or else some error message if not. -## - -ModemFind: - -# Do a quick check first... - - set $ErrorMsg "" - call ModemFind4 - if $modemCmdResult == "OK" return - if $Serial230K != "yes" goto ModemFind1 - set $newBaudrate 230400 - if $Baudrate == "230400" set $newBaudrate 115200 - set $Baudrate $newBaudrate - call ModemFind4 - if $modemCmdResult == "OK" return - -# Now try possible baud rates more extensively - -ModemFind1: - set $Baudrate 115200 - call ModemFind2 - if $modemCmdResult == "OK" return - if $Serial230K != "yes" return - set $Baudrate 230400 - wait 1 - call ModemFind2 - if $modemCmdResult == "OK" return - set $ErrorMsg "The modem is not responding." - return - -# This tries the +++ sequence in case the modem is in "on-line" mode - -ModemFind2: - call ModemFind3 - if $modemCmdResult == "OK" return - call SendTriplePlus - call ModemFind3 - return - -# This tries a few commands to see if the modem responds with "OK" - -ModemFind3: - set $modemCmd "" - set $modemCmdTimeout 1 - call ModemCmd0 - if $modemCmdResult == "OK" return - set $modemCmd "Z" - set $modemCmdTimeout 2 - call ModemCmd0 - if $modemCmdResult == "OK" return -ModemFind4: - set $modemCmd "" - set $modemCmdTimeout 1 - call ModemCmd0 - return - -## -## SetBaudrate -## -## Change baud rates (as allowed) and verify modem is still there. -## If not, then fail the script. -## -## $newBaudrate New baud rate; if we don't support it, just return. -## $modemCmd Command to send modem to jump to the new baud rate. -## - -SetBaudrate: - if $Baudrate == $newBaudrate return - if $newBaudrate != 230400 goto SetBaudrate2 - if $Serial230K != "yes" return -SetBaudrate2: - log "Setting serial port speed to $newBaudrate..." - print "AT$modemCmd\r\n" - wait 1 - set $Baudrate $newBaudrate - wait 1 - set $modemCmd "" - goto ModemCmd2 - -## -## ModemCheckValue -## -## Check the value in an S-register (or equivalent). If it is -## not what we want, then change it and set $valueChanged to "yes", -## and log $checkMsg (if not empty). The value $checkValueNew is -## what we program the S-register to equal if it doesn't match. -## -## The $checkValue must match exactly on the first line of output. -## If we get any weird error, then fail the script. -## - -ModemCheckValue: - set $modemCmd "${checkCmd}?" - call ModemQuery - if $modemQuery == $checkValue return - set $valueChanged "yes" - set $checkValueMyNew $checkValueNew - if $checkValueNew == "" set $checkValueMyNew $checkValue - set $modemCmd "${checkCmd}=${checkValueMyNew}" - if $checkMsg != "" log $checkMsg - goto ModemCmd2 - -## -## ModemCmd -## -## Do the modem command in $modemCmd. Set $modemCmdResult to -## -## OK The modem returned "OK" -## ERROR The modem returned "ERR" or "ERROR" -## TIMEOUT The modem did not respond within three seconds -## -## If ERR or TIMEOUT, also set $ErrorMsg to an appropriate message -## - -ModemCmd: - set $modemCmdTimeout 3 -ModemCmd0: - print "AT$modemCmd\r\n" - match "OK\r\n" ModemCmdOk - match "ERR" ModemCmdErr - wait $modemCmdTimeout - set $modemCmdResult "TIMEOUT" -ModemCmdTimeout: - set $ErrorMsg "The modem is not responding to \"AT$modemCmd\" at ModemCmd: label." - return -ModemCmdOk: - set $modemCmdResult "OK" - return -ModemCmdErr: - set $modemCmdResult "ERROR" - set $ErrorMsg "The modem responded with \"ERROR\" to the command \"AT$modemCmd\" at ModemCmd: label." - return - -## -## ModemCmd2 -## -## Do the modem command in $modemCmd. If we don't get OK back, -## fail the script and log an error message. -## - -ModemCmd2: - call ModemCmd - if $modemCmdResult == "OK" return - log $ErrorMsg - failure - -## -## ModemCmdSend -## -## Send a modem command and read the echo'ed CR-LF -## - -ModemCmdSend: - print "AT$modemCmd\r\n" - match "\r\n" ModemCmdSend2 - wait 3 - goto ModemCmdTimeout -ModemCmdSend2: - return - -## -## ModemQuery -## -## Do the $modemCmd and expect exactly one line of response, then OK. -## Return the response in $modemQuery. If anything goes wrong, die. -## - -ModemQuery: - call ModemCmdSend - call ReadLine - set $modemQuery $matchedString - if $modemQuery == "ERR" goto ModemQueryError - if $modemQuery == "ERROR" goto ModemQueryError - goto GetOK -ModemQueryError: - call ModemCmdErr - failure - -# Same thing, but strip leading and trailing blanks - -ModemQueryStrip: - call ModemQuery - if $modemQuery match " *(.*) *" nop - set $modemQuery $matchedString1 - return - -## -## ReadLine -## -## Read the next line of output. It should come within $modemCmdTimeout -## seconds, or else we fail. Return it in $matchedString. -## - -ReadLine: - regex "^.*$" ReadLineDone - wait $modemCmdTimeout - set $ErrorMsg "The modem is not responding." - log $ErrorMsg - failure -ReadLineDone: - return - -## -## Get an OK within 3 seconds or die -## - -GetOK: - match "OK\r\n" GotOK - wait 3 - log "The modem did not respond with \"OK\"." - failure -GotOK: - return - -## -## Send "+++" to get modem attention if on-line -## - -SendTriplePlus: - print "\r\n" - wait 2 - print "+++" - wait 2 - return - -################################################################# -# -# LOGIN AUTO-SCRIPTING -# -################################################################# - -## -## AutoLogin -## -## Here we attempt to figure out what the remote server wants -## from us. We do this by checking for bytes that correspond -## to PPP packets (in which case we are done) as well as common -## login type stuff like "name:", "ogin:", etc. -## -## This always returns. The hope is that when it returns, the -## remote side has reached PPP mode. -## -## This has been crafted from empirical evidence. Lots of terminal -## servers have various intelligent/stupid features which we -## take advantage of/have to work around. -## -## Variables (set automatically by mpd): -## -## $Login Authorization login -## $Password Authorization password -## - -AutoLogin: - log "Initiating auto-login..." - -# Spend at most this long doing auto-login before giving up - - timer autoLogin 5 AutoLoginTimeout - -# At any time if we see an LCP frame (not our own echo) then we're done - - match autoLogin "\x7e\xff\x03\xc0\x21" AutoLoginFrame - match autoLogin "\x7e\xff\x7d\x23\xc0\x21\x7d\x21" AutoLoginFrame - match autoLogin "\x7e\xc0\x21" AutoLoginFrame - -# Now send a "fake" PPP frame (this is an empty config-reject with id# 172). -# This should trigger any auto-detecting servers to jump into PPP mode, -# which is good because it's faster (by avoiding human readable messages) -# and more reliable (PPP framing). - - print "\x7e\xff\x7d\x23\xc0\x21\x7d\x24\xac\x7d\x20\x7d\x24\x2e\x2b\x7e" - -# Wait one second for server to auto-detect PPP or send a login prompt. -# After one second of neither, try sending a carriage return (some servers -# require this). After that, we have to see something recognizable from -# the peer, otherwise we'll just timeout. - - match "ogin" AutoLoginPrompt - match "name" AutoLoginPrompt - wait 1 - print "\r" - match "ogin" AutoLoginPrompt - match "name" AutoLoginPrompt - wait - -# At this point we've seen a login prompt; do the manual login - -AutoLoginPrompt: - log "Sending login..." - print "${Login}\r" - match "word" - wait - log "Sending password..." - print "${Password}\r" - match "\r" - wait - if $didLogin != "yes" match "ogin:" LoginAgain - match ">" - match "%" - match ":" - wait - log "Enabling PPP..." - print "ppp\r" - cancel all - return - -LoginAgain: - set $didLogin "yes" - goto AutoLoginPrompt - -# We saw a PPP frame - -AutoLoginFrame: - log "Detected PPP frame." - cancel all - return - -# We timed out before seeing a PPP frame. Cross your fingers and pray. - -AutoLoginTimeout: - log "Auto-login timeout." - cancel all - return - |
