summaryrefslogtreecommitdiffstats
path: root/include/linux/regulator/gpio-regulator.h
blob: 19fbd267406d1c39b96a6da55ccde15b84487188 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
/*
 * gpio-regulator.h
 *
 * Copyright 2011 Heiko Stuebner <heiko@sntech.de>
 *
 * based on fixed.h
 *
 * Copyright 2008 Wolfson Microelectronics PLC.
 *
 * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
 *
 * Copyright (c) 2009 Nokia Corporation
 * Roger Quadros <ext-roger.quadros@nokia.com>
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of the
 * License, or (at your option) any later version.
 */

#ifndef __REGULATOR_GPIO_H
#define __REGULATOR_GPIO_H

struct regulator_init_data;

enum regulator_type;

/**
 * struct gpio_regulator_state - state description
 * @value:		microvolts or microamps
 * @gpios:		bitfield of gpio target-states for the value
 *
 * This structure describes a supported setting of the regulator
 * and the necessary gpio-state to achieve it.
 *
 * The n-th bit in the bitfield describes the state of the n-th GPIO
 * from the gpios-array defined in gpio_regulator_config below.
 */
struct gpio_regulator_state {
	int value;
	int gpios;
};

/**
 * struct gpio_regulator_config - config structure
 * @supply_name:	Name of the regulator supply
 * @enable_gpio:	GPIO to use for enable control
 *			set to -EINVAL if not used
 * @enable_high:	Polarity of enable GPIO
 *			1 = Active high, 0 = Active low
 * @enabled_at_boot:	Whether regulator has been enabled at
 *			boot or not. 1 = Yes, 0 = No
 *			This is used to keep the regulator at
 *			the default state
 * @startup_delay:	Start-up time in microseconds
 * @gpios:		Array containing the gpios needed to control
 *			the setting of the regulator
 * @nr_gpios:		Number of gpios
 * @states:		Array of gpio_regulator_state entries describing
 *			the gpio state for specific voltages
 * @nr_states:		Number of states available
 * @regulator_type:	either REGULATOR_CURRENT or REGULATOR_VOLTAGE
 * @init_data:		regulator_init_data
 *
 * This structure contains gpio-voltage regulator configuration
 * information that must be passed by platform code to the
 * gpio-voltage regulator driver.
 */
struct gpio_regulator_config {
	const char *supply_name;

	int enable_gpio;
	unsigned enable_high:1;
	unsigned enabled_at_boot:1;
	unsigned startup_delay;

	struct gpio *gpios;
	int nr_gpios;

	struct gpio_regulator_state *states;
	int nr_states;

	enum regulator_type type;
	struct regulator_init_data *init_data;
};

#endif
OpenPOWER on IntegriCloud