summaryrefslogtreecommitdiffstats
path: root/include/asm-sh/se/smc37c93x.h
blob: 585da2a8fc454ae6aed22718d0806f0b2c7e8521 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
#ifndef __ASM_SH_SMC37C93X_H
#define __ASM_SH_SMC37C93X_H

/*
 * linux/include/asm-sh/smc37c93x.h
 *
 * Copyright (C) 2000  Kazumoto Kojima
 *
 * SMSC 37C93x Super IO Chip support
 */

/* Default base I/O address */
#define FDC_PRIMARY_BASE	0x3f0
#define IDE1_PRIMARY_BASE	0x1f0
#define IDE1_SECONDARY_BASE	0x170
#define PARPORT_PRIMARY_BASE	0x378
#define COM1_PRIMARY_BASE	0x2f8
#define COM2_PRIMARY_BASE	0x3f8
#define RTC_PRIMARY_BASE	0x070
#define KBC_PRIMARY_BASE	0x060
#define AUXIO_PRIMARY_BASE	0x000	/* XXX */

/* Logical device number */
#define LDN_FDC			0
#define LDN_IDE1		1
#define LDN_IDE2		2
#define LDN_PARPORT		3
#define LDN_COM1		4
#define LDN_COM2		5
#define LDN_RTC			6
#define LDN_KBC			7
#define LDN_AUXIO		8

/* Configuration port and key */
#define CONFIG_PORT		0x3f0
#define INDEX_PORT		CONFIG_PORT
#define DATA_PORT		0x3f1
#define CONFIG_ENTER		0x55
#define CONFIG_EXIT		0xaa

/* Configuration index */
#define CURRENT_LDN_INDEX	0x07
#define POWER_CONTROL_INDEX	0x22
#define ACTIVATE_INDEX		0x30
#define IO_BASE_HI_INDEX	0x60
#define IO_BASE_LO_INDEX	0x61
#define IRQ_SELECT_INDEX	0x70
#define DMA_SELECT_INDEX	0x74

#define GPIO46_INDEX		0xc6
#define GPIO47_INDEX		0xc7

/* UART stuff. Only for debugging.  */
/* UART Register */

#define UART_RBR	0x0	/* Receiver Buffer Register (Read Only) */
#define UART_THR	0x0	/* Transmitter Holding Register (Write Only) */
#define UART_IER	0x2	/* Interrupt Enable Register */
#define UART_IIR	0x4	/* Interrupt Ident Register (Read Only) */
#define UART_FCR	0x4	/* FIFO Control Register (Write Only) */
#define UART_LCR	0x6	/* Line Control Register */
#define UART_MCR	0x8	/* MODEM Control Register */
#define UART_LSR	0xa	/* Line Status Register */
#define UART_MSR	0xc	/* MODEM Status Register */
#define UART_SCR	0xe	/* Scratch Register */
#define UART_DLL	0x0	/* Divisor Latch (LS) */
#define UART_DLM	0x2	/* Divisor Latch (MS) */

#ifndef __ASSEMBLY__
typedef struct uart_reg {
	volatile __u16 rbr;
	volatile __u16 ier;
	volatile __u16 iir;
	volatile __u16 lcr;
	volatile __u16 mcr;
	volatile __u16 lsr;
	volatile __u16 msr;
	volatile __u16 scr;
} uart_reg;
#endif /* ! __ASSEMBLY__ */

/* Alias for Write Only Register */

#define thr	rbr
#define tcr	iir

/* Alias for Divisor Latch Register */

#define dll	rbr
#define dlm	ier
#define fcr	iir

/* Interrupt Enable Register */

#define IER_ERDAI	0x0100	/* Enable Received Data Available Interrupt */
#define IER_ETHREI	0x0200	/* Enable Transmitter Holding Register Empty Interrupt */
#define IER_ELSI	0x0400	/* Enable Receiver Line Status Interrupt */
#define IER_EMSI	0x0800	/* Enable MODEM Status Interrupt */

/* Interrupt Ident Register */

#define IIR_IP		0x0100	/* "0" if Interrupt Pending */
#define IIR_IIB0	0x0200	/* Interrupt ID Bit 0 */
#define IIR_IIB1	0x0400	/* Interrupt ID Bit 1 */
#define IIR_IIB2	0x0800	/* Interrupt ID Bit 2 */
#define IIR_FIFO	0xc000	/* FIFOs enabled */

/* FIFO Control Register */

#define FCR_FEN		0x0100	/* FIFO enable */
#define FCR_RFRES	0x0200	/* Receiver FIFO reset */
#define FCR_TFRES	0x0400	/* Transmitter FIFO reset */
#define FCR_DMA		0x0800	/* DMA mode select */
#define FCR_RTL		0x4000	/* Receiver triger (LSB) */
#define FCR_RTM		0x8000	/* Receiver triger (MSB) */

/* Line Control Register */

#define LCR_WLS0	0x0100	/* Word Length Select Bit 0 */
#define LCR_WLS1	0x0200	/* Word Length Select Bit 1 */
#define LCR_STB		0x0400	/* Number of Stop Bits */
#define LCR_PEN		0x0800	/* Parity Enable */
#define LCR_EPS		0x1000	/* Even Parity Select */
#define LCR_SP		0x2000	/* Stick Parity */
#define LCR_SB		0x4000	/* Set Break */
#define LCR_DLAB	0x8000	/* Divisor Latch Access Bit */

/* MODEM Control Register */

#define MCR_DTR		0x0100	/* Data Terminal Ready */
#define MCR_RTS		0x0200	/* Request to Send */
#define MCR_OUT1	0x0400	/* Out 1 */
#define MCR_IRQEN	0x0800	/* IRQ Enable */
#define MCR_LOOP	0x1000	/* Loop */

/* Line Status Register */

#define LSR_DR		0x0100	/* Data Ready */
#define LSR_OE		0x0200	/* Overrun Error */
#define LSR_PE		0x0400	/* Parity Error */
#define LSR_FE		0x0800	/* Framing Error */
#define LSR_BI		0x1000	/* Break Interrupt */
#define LSR_THRE	0x2000	/* Transmitter Holding Register Empty */
#define LSR_TEMT	0x4000	/* Transmitter Empty */
#define LSR_FIFOE	0x8000	/* Receiver FIFO error */

/* MODEM Status Register */

#define MSR_DCTS	0x0100	/* Delta Clear to Send */
#define MSR_DDSR	0x0200	/* Delta Data Set Ready */
#define MSR_TERI	0x0400	/* Trailing Edge Ring Indicator */
#define MSR_DDCD	0x0800	/* Delta Data Carrier Detect */
#define MSR_CTS		0x1000	/* Clear to Send */
#define MSR_DSR		0x2000	/* Data Set Ready */
#define MSR_RI		0x4000	/* Ring Indicator */
#define MSR_DCD		0x8000	/* Data Carrier Detect */

/* Baud Rate Divisor */

#define UART_CLK	(1843200)	/* 1.8432 MHz */
#define UART_BAUD(x)	(UART_CLK / (16 * (x)))

/* RTC register definition */
#define RTC_SECONDS             0
#define RTC_SECONDS_ALARM       1
#define RTC_MINUTES             2
#define RTC_MINUTES_ALARM       3
#define RTC_HOURS               4
#define RTC_HOURS_ALARM         5
#define RTC_DAY_OF_WEEK         6
#define RTC_DAY_OF_MONTH        7
#define RTC_MONTH               8
#define RTC_YEAR                9
#define RTC_FREQ_SELECT		10
# define RTC_UIP 0x80
# define RTC_DIV_CTL 0x70
/* This RTC can work under 32.768KHz clock only.  */
# define RTC_OSC_ENABLE 0x20
# define RTC_OSC_DISABLE 0x00
#define RTC_CONTROL     	11
# define RTC_SET 0x80
# define RTC_PIE 0x40
# define RTC_AIE 0x20
# define RTC_UIE 0x10
# define RTC_SQWE 0x08
# define RTC_DM_BINARY 0x04
# define RTC_24H 0x02
# define RTC_DST_EN 0x01

#endif  /* __ASM_SH_SMC37C93X_H */
OpenPOWER on IntegriCloud