1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
|
/*
* FB driver for the SSD1306 OLED Controller
*
* Copyright (C) 2013 Noralf Tronnes
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include "fbtft.h"
#define DRVNAME "fb_ssd1306"
#define WIDTH 128
#define HEIGHT 64
/*
write_reg() caveat:
This doesn't work because D/C has to be LOW for both values:
write_reg(par, val1, val2);
Do it like this:
write_reg(par, val1);
write_reg(par, val2);
*/
/* Init sequence taken from the Adafruit SSD1306 Arduino library */
static int init_display(struct fbtft_par *par)
{
par->fbtftops.reset(par);
if (par->gamma.curves[0] == 0) {
mutex_lock(&par->gamma.lock);
if (par->info->var.yres == 64)
par->gamma.curves[0] = 0xCF;
else
par->gamma.curves[0] = 0x8F;
mutex_unlock(&par->gamma.lock);
}
/* Set Display OFF */
write_reg(par, 0xAE);
/* Set Display Clock Divide Ratio/ Oscillator Frequency */
write_reg(par, 0xD5);
write_reg(par, 0x80);
/* Set Multiplex Ratio */
write_reg(par, 0xA8);
if (par->info->var.yres == 64)
write_reg(par, 0x3F);
else
write_reg(par, 0x1F);
/* Set Display Offset */
write_reg(par, 0xD3);
write_reg(par, 0x0);
/* Set Display Start Line */
write_reg(par, 0x40 | 0x0);
/* Charge Pump Setting */
write_reg(par, 0x8D);
/* A[2] = 1b, Enable charge pump during display on */
write_reg(par, 0x14);
/* Set Memory Addressing Mode */
write_reg(par, 0x20);
/* Vertical addressing mode */
write_reg(par, 0x01);
/*Set Segment Re-map */
/* column address 127 is mapped to SEG0 */
write_reg(par, 0xA0 | 0x1);
/* Set COM Output Scan Direction */
/* remapped mode. Scan from COM[N-1] to COM0 */
write_reg(par, 0xC8);
/* Set COM Pins Hardware Configuration */
write_reg(par, 0xDA);
if (par->info->var.yres == 64)
/* A[4]=1b, Alternative COM pin configuration */
write_reg(par, 0x12);
else
/* A[4]=0b, Sequential COM pin configuration */
write_reg(par, 0x02);
/* Set Pre-charge Period */
write_reg(par, 0xD9);
write_reg(par, 0xF1);
/* Set VCOMH Deselect Level */
write_reg(par, 0xDB);
/* according to the datasheet, this value is out of bounds */
write_reg(par, 0x40);
/* Entire Display ON */
/* Resume to RAM content display. Output follows RAM content */
write_reg(par, 0xA4);
/* Set Normal Display
0 in RAM: OFF in display panel
1 in RAM: ON in display panel */
write_reg(par, 0xA6);
/* Set Display ON */
write_reg(par, 0xAF);
return 0;
}
static void set_addr_win(struct fbtft_par *par, int xs, int ys, int xe, int ye)
{
/* Set Lower Column Start Address for Page Addressing Mode */
write_reg(par, 0x00 | 0x0);
/* Set Higher Column Start Address for Page Addressing Mode */
write_reg(par, 0x10 | 0x0);
/* Set Display Start Line */
write_reg(par, 0x40 | 0x0);
}
static int blank(struct fbtft_par *par, bool on)
{
fbtft_par_dbg(DEBUG_BLANK, par, "%s(blank=%s)\n",
__func__, on ? "true" : "false");
if (on)
write_reg(par, 0xAE);
else
write_reg(par, 0xAF);
return 0;
}
/* Gamma is used to control Contrast */
static int set_gamma(struct fbtft_par *par, unsigned long *curves)
{
/* apply mask */
curves[0] &= 0xFF;
/* Set Contrast Control for BANK0 */
write_reg(par, 0x81);
write_reg(par, curves[0]);
return 0;
}
static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
{
u16 *vmem16 = (u16 *)par->info->screen_base;
u8 *buf = par->txbuf.buf;
int x, y, i;
int ret = 0;
fbtft_par_dbg(DEBUG_WRITE_VMEM, par, "%s()\n", __func__);
for (x = 0; x < par->info->var.xres; x++) {
for (y = 0; y < par->info->var.yres/8; y++) {
*buf = 0x00;
for (i = 0; i < 8; i++)
*buf |= (vmem16[(y * 8 + i) *
par->info->var.xres + x] ?
1 : 0) << i;
buf++;
}
}
/* Write data */
gpio_set_value(par->gpio.dc, 1);
ret = par->fbtftops.write(par, par->txbuf.buf,
par->info->var.xres * par->info->var.yres /
8);
if (ret < 0)
dev_err(par->info->device, "write failed and returned: %d\n",
ret);
return ret;
}
static struct fbtft_display display = {
.regwidth = 8,
.width = WIDTH,
.height = HEIGHT,
.gamma_num = 1,
.gamma_len = 1,
.gamma = "00",
.fbtftops = {
.write_vmem = write_vmem,
.init_display = init_display,
.set_addr_win = set_addr_win,
.blank = blank,
.set_gamma = set_gamma,
},
};
FBTFT_REGISTER_DRIVER(DRVNAME, "solomon,ssd1306", &display);
MODULE_ALIAS("spi:" DRVNAME);
MODULE_ALIAS("platform:" DRVNAME);
MODULE_ALIAS("spi:ssd1306");
MODULE_ALIAS("platform:ssd1306");
MODULE_DESCRIPTION("SSD1306 OLED Driver");
MODULE_AUTHOR("Noralf Tronnes");
MODULE_LICENSE("GPL");
|