1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
|
//------------------------------------------------------------------------------
// Copyright (c) 2004-2010 Atheros Corporation. All rights reserved.
//
//
// Permission to use, copy, modify, and/or distribute this software for any
// purpose with or without fee is hereby granted, provided that the above
// copyright notice and this permission notice appear in all copies.
//
// THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
// WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
// MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
// ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
// WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
// ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
// OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
//
//
//------------------------------------------------------------------------------
//==============================================================================
// This file contains the tunable configuration items for the WLAN module
//
// Author(s): ="Atheros"
//==============================================================================
#ifndef _HOST_WLAN_CONFIG_H_
#define _HOST_WLAN_CONFIG_H_
/* Include definitions here that can be used to tune the WLAN module behavior.
* Different customers can tune the behavior as per their needs, here.
*/
/* This configuration item when defined will consider the barker preamble
* mentioned in the ERP IE of the beacons from the AP to determine the short
* preamble support sent in the (Re)Assoc request frames.
*/
#define WLAN_CONFIG_DONOT_IGNORE_BARKER_IN_ERP 0
/* This config item when defined will not send the power module state transition
* failure events that happen during scan, to the host.
*/
#define WLAN_CONFIG_IGNORE_POWER_SAVE_FAIL_EVENT_DURING_SCAN 0
/*
* This configuration item enable/disable keepalive support.
* Keepalive support: In the absence of any data traffic to AP, null
* frames will be sent to the AP at periodic interval, to keep the association
* active. This configuration item defines the periodic interval.
* Use value of zero to disable keepalive support
* Default: 60 seconds
*/
#define WLAN_CONFIG_KEEP_ALIVE_INTERVAL 60
/*
* This configuration item sets the value of disconnect timeout
* Firmware delays sending the disconnec event to the host for this
* timeout after is gets disconnected from the current AP.
* If the firmware successly roams within the disconnect timeout
* it sends a new connect event
*/
#define WLAN_CONFIG_DISCONNECT_TIMEOUT 10
/*
* This configuration item disables 11n support.
* 0 - Enable
* 1 - Disable
*/
#define WLAN_CONFIG_DISABLE_11N 0
/*
* This configuration item enable BT clock sharing support
* 1 - Enable
* 0 - Disable (Default)
*/
#define WLAN_CONFIG_BT_SHARING 0
/*
* This configuration item sets WIFI OFF policy
* 0 - CUT_POWER
* 1 - DEEP_SLEEP (Default)
*/
#define WLAN_CONFIG_WLAN_OFF 1
/*
* This configuration item sets suspend policy
* 0 - CUT_POWER (Default)
* 1 - DEEP_SLEEP
* 2 - WoW
* 3 - CUT_POWER if BT OFF (clock sharing designs only)
*/
#define WLAN_CONFIG_PM_SUSPEND 0
/*
* This configuration item sets suspend policy to use if PM_SUSPEND is
* set to WoW and device is not connected at the time of suspend
* 0 - CUT_POWER (Default)
* 1 - DEEP_SLEEP
* 2 - WoW
* 3 - CUT_POWER if BT OFF (clock sharing designs only)
*/
#define WLAN_CONFIG_PM_WOW2 0
/*
* This configuration item enables/disables transmit bursting
* 0 - Enable tx Bursting (default)
* 1 - Disable tx bursting
*/
#define WLAN_CONFIG_DISABLE_TX_BURSTING 0
/*
* Platform specific function to power ON/OFF AR6000
* and enable/disable SDIO card detection
*/
#define plat_setup_power(on, detect)
#endif /* _HOST_WLAN_CONFIG_H_ */
|