1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
|
/*
* include/asm/dma.h
*
* Copyright 1996 (C) David S. Miller (davem@caip.rutgers.edu)
*/
#ifndef _ASM_SPARC64_DMA_H
#define _ASM_SPARC64_DMA_H
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/spinlock.h>
#include <asm/sbus.h>
#include <asm/delay.h>
#include <asm/oplib.h>
/* These are irrelevant for Sparc DMA, but we leave it in so that
* things can compile.
*/
#define MAX_DMA_CHANNELS 8
#define DMA_MODE_READ 1
#define DMA_MODE_WRITE 2
#define MAX_DMA_ADDRESS (~0UL)
/* Useful constants */
#define SIZE_16MB (16*1024*1024)
#define SIZE_64K (64*1024)
/* SBUS DMA controller reg offsets */
#define DMA_CSR 0x00UL /* rw DMA control/status register 0x00 */
#define DMA_ADDR 0x04UL /* rw DMA transfer address register 0x04 */
#define DMA_COUNT 0x08UL /* rw DMA transfer count register 0x08 */
#define DMA_TEST 0x0cUL /* rw DMA test/debug register 0x0c */
/* DVMA chip revisions */
enum dvma_rev {
dvmarev0,
dvmaesc1,
dvmarev1,
dvmarev2,
dvmarev3,
dvmarevplus,
dvmahme
};
#define DMA_HASCOUNT(rev) ((rev)==dvmaesc1)
/* Linux DMA information structure, filled during probe. */
struct sbus_dma {
struct sbus_dma *next;
struct sbus_dev *sdev;
void __iomem *regs;
/* Status, misc info */
int node; /* Prom node for this DMA device */
int running; /* Are we doing DMA now? */
int allocated; /* Are we "owned" by anyone yet? */
/* Transfer information. */
u32 addr; /* Start address of current transfer */
int nbytes; /* Size of current transfer */
int realbytes; /* For splitting up large transfers, etc. */
/* DMA revision */
enum dvma_rev revision;
};
extern struct sbus_dma *dma_chain;
/* Broken hardware... */
#define DMA_ISBROKEN(dma) ((dma)->revision == dvmarev1)
#define DMA_ISESC1(dma) ((dma)->revision == dvmaesc1)
/* Main routines in dma.c */
extern void dvma_init(struct sbus_bus *);
/* Fields in the cond_reg register */
/* First, the version identification bits */
#define DMA_DEVICE_ID 0xf0000000 /* Device identification bits */
#define DMA_VERS0 0x00000000 /* Sunray DMA version */
#define DMA_ESCV1 0x40000000 /* DMA ESC Version 1 */
#define DMA_VERS1 0x80000000 /* DMA rev 1 */
#define DMA_VERS2 0xa0000000 /* DMA rev 2 */
#define DMA_VERHME 0xb0000000 /* DMA hme gate array */
#define DMA_VERSPLUS 0x90000000 /* DMA rev 1 PLUS */
#define DMA_HNDL_INTR 0x00000001 /* An IRQ needs to be handled */
#define DMA_HNDL_ERROR 0x00000002 /* We need to take an error */
#define DMA_FIFO_ISDRAIN 0x0000000c /* The DMA FIFO is draining */
#define DMA_INT_ENAB 0x00000010 /* Turn on interrupts */
#define DMA_FIFO_INV 0x00000020 /* Invalidate the FIFO */
#define DMA_ACC_SZ_ERR 0x00000040 /* The access size was bad */
#define DMA_FIFO_STDRAIN 0x00000040 /* DMA_VERS1 Drain the FIFO */
#define DMA_RST_SCSI 0x00000080 /* Reset the SCSI controller */
#define DMA_RST_ENET DMA_RST_SCSI /* Reset the ENET controller */
#define DMA_ST_WRITE 0x00000100 /* write from device to memory */
#define DMA_ENABLE 0x00000200 /* Fire up DMA, handle requests */
#define DMA_PEND_READ 0x00000400 /* DMA_VERS1/0/PLUS Pending Read */
#define DMA_ESC_BURST 0x00000800 /* 1=16byte 0=32byte */
#define DMA_READ_AHEAD 0x00001800 /* DMA read ahead partial longword */
#define DMA_DSBL_RD_DRN 0x00001000 /* No EC drain on slave reads */
#define DMA_BCNT_ENAB 0x00002000 /* If on, use the byte counter */
#define DMA_TERM_CNTR 0x00004000 /* Terminal counter */
#define DMA_SCSI_SBUS64 0x00008000 /* HME: Enable 64-bit SBUS mode. */
#define DMA_CSR_DISAB 0x00010000 /* No FIFO drains during csr */
#define DMA_SCSI_DISAB 0x00020000 /* No FIFO drains during reg */
#define DMA_DSBL_WR_INV 0x00020000 /* No EC inval. on slave writes */
#define DMA_ADD_ENABLE 0x00040000 /* Special ESC DVMA optimization */
#define DMA_E_BURSTS 0x000c0000 /* ENET: SBUS r/w burst mask */
#define DMA_E_BURST32 0x00040000 /* ENET: SBUS 32 byte r/w burst */
#define DMA_E_BURST16 0x00000000 /* ENET: SBUS 16 byte r/w burst */
#define DMA_BRST_SZ 0x000c0000 /* SCSI: SBUS r/w burst size */
#define DMA_BRST64 0x000c0000 /* SCSI: 64byte bursts (HME on UltraSparc only) */
#define DMA_BRST32 0x00040000 /* SCSI: 32byte bursts */
#define DMA_BRST16 0x00000000 /* SCSI: 16byte bursts */
#define DMA_BRST0 0x00080000 /* SCSI: no bursts (non-HME gate arrays) */
#define DMA_ADDR_DISAB 0x00100000 /* No FIFO drains during addr */
#define DMA_2CLKS 0x00200000 /* Each transfer = 2 clock ticks */
#define DMA_3CLKS 0x00400000 /* Each transfer = 3 clock ticks */
#define DMA_EN_ENETAUI DMA_3CLKS /* Put lance into AUI-cable mode */
#define DMA_CNTR_DISAB 0x00800000 /* No IRQ when DMA_TERM_CNTR set */
#define DMA_AUTO_NADDR 0x01000000 /* Use "auto nxt addr" feature */
#define DMA_SCSI_ON 0x02000000 /* Enable SCSI dma */
#define DMA_PARITY_OFF 0x02000000 /* HME: disable parity checking */
#define DMA_LOADED_ADDR 0x04000000 /* Address has been loaded */
#define DMA_LOADED_NADDR 0x08000000 /* Next address has been loaded */
#define DMA_RESET_FAS366 0x08000000 /* HME: Assert RESET to FAS366 */
/* Values describing the burst-size property from the PROM */
#define DMA_BURST1 0x01
#define DMA_BURST2 0x02
#define DMA_BURST4 0x04
#define DMA_BURST8 0x08
#define DMA_BURST16 0x10
#define DMA_BURST32 0x20
#define DMA_BURST64 0x40
#define DMA_BURSTBITS 0x7f
/* Determine highest possible final transfer address given a base */
#define DMA_MAXEND(addr) (0x01000000UL-(((unsigned long)(addr))&0x00ffffffUL))
/* Yes, I hack a lot of elisp in my spare time... */
#define DMA_ERROR_P(regs) ((sbus_readl((regs) + DMA_CSR) & DMA_HNDL_ERROR))
#define DMA_IRQ_P(regs) ((sbus_readl((regs) + DMA_CSR)) & (DMA_HNDL_INTR | DMA_HNDL_ERROR))
#define DMA_WRITE_P(regs) ((sbus_readl((regs) + DMA_CSR) & DMA_ST_WRITE))
#define DMA_OFF(__regs) \
do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \
tmp &= ~DMA_ENABLE; \
sbus_writel(tmp, (__regs) + DMA_CSR); \
} while(0)
#define DMA_INTSOFF(__regs) \
do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \
tmp &= ~DMA_INT_ENAB; \
sbus_writel(tmp, (__regs) + DMA_CSR); \
} while(0)
#define DMA_INTSON(__regs) \
do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \
tmp |= DMA_INT_ENAB; \
sbus_writel(tmp, (__regs) + DMA_CSR); \
} while(0)
#define DMA_PUNTFIFO(__regs) \
do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \
tmp |= DMA_FIFO_INV; \
sbus_writel(tmp, (__regs) + DMA_CSR); \
} while(0)
#define DMA_SETSTART(__regs, __addr) \
sbus_writel((u32)(__addr), (__regs) + DMA_ADDR);
#define DMA_BEGINDMA_W(__regs) \
do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \
tmp |= (DMA_ST_WRITE|DMA_ENABLE|DMA_INT_ENAB); \
sbus_writel(tmp, (__regs) + DMA_CSR); \
} while(0)
#define DMA_BEGINDMA_R(__regs) \
do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \
tmp |= (DMA_ENABLE|DMA_INT_ENAB); \
tmp &= ~DMA_ST_WRITE; \
sbus_writel(tmp, (__regs) + DMA_CSR); \
} while(0)
/* For certain DMA chips, we need to disable ints upon irq entry
* and turn them back on when we are done. So in any ESP interrupt
* handler you *must* call DMA_IRQ_ENTRY upon entry and DMA_IRQ_EXIT
* when leaving the handler. You have been warned...
*/
#define DMA_IRQ_ENTRY(dma, dregs) do { \
if(DMA_ISBROKEN(dma)) DMA_INTSOFF(dregs); \
} while (0)
#define DMA_IRQ_EXIT(dma, dregs) do { \
if(DMA_ISBROKEN(dma)) DMA_INTSON(dregs); \
} while(0)
#define for_each_dvma(dma) \
for((dma) = dma_chain; (dma); (dma) = (dma)->next)
/* From PCI */
#ifdef CONFIG_PCI
extern int isa_dma_bridge_buggy;
#else
#define isa_dma_bridge_buggy (0)
#endif
#endif /* !(_ASM_SPARC64_DMA_H) */
|
