1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
/*
* Copyright 2000 MontaVista Software Inc.
* Author: MontaVista Software, Inc.
* ppopov@mvista.com or source@mvista.com
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/config.h>
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/ioport.h>
#include <linux/mm.h>
#include <linux/console.h>
#include <linux/delay.h>
#include <asm/cpu.h>
#include <asm/bootinfo.h>
#include <asm/irq.h>
#include <asm/mipsregs.h>
#include <asm/reboot.h>
#include <asm/pgtable.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1500.h>
void board_reset (void)
{
/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
au_writel(0x00000000, 0xAE00001C);
}
void __init board_setup(void)
{
u32 pin_func;
u32 sys_freqctrl, sys_clksrc;
sys_clksrc = sys_freqctrl = pin_func = 0;
// set AUX clock to 12MHz * 8 = 96 MHz
au_writel(8, SYS_AUXPLL);
au_writel(0, SYS_PINSTATERD);
udelay(100);
#if defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE)
/* GPIO201 is input for PCMCIA card detect */
/* GPIO203 is input for PCMCIA interrupt request */
au_writel(au_readl(GPIO2_DIR) & (u32)(~((1<<1)|(1<<3))), GPIO2_DIR);
/* zero and disable FREQ2 */
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/* zero and disable USBH/USBD clocks */
sys_clksrc = au_readl(SYS_CLKSRC);
sys_clksrc &= ~0x00007FE0;
au_writel(sys_clksrc, SYS_CLKSRC);
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
sys_clksrc = au_readl(SYS_CLKSRC);
sys_clksrc &= ~0x00007FE0;
// FREQ2 = aux/2 = 48 MHz
sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/*
* Route 48MHz FREQ2 into USB Host and/or Device
*/
#ifdef CONFIG_USB_OHCI
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
#endif
#ifdef CONFIG_AU1X00_USB_DEVICE
sys_clksrc |= ((4<<7) | (0<<6) | (0<<5));
#endif
au_writel(sys_clksrc, SYS_CLKSRC);
pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000);
#ifndef CONFIG_AU1X00_USB_DEVICE
// 2nd USB port is USB host
pin_func |= 0x8000;
#endif
au_writel(pin_func, SYS_PINFUNC);
#endif // defined (CONFIG_USB_OHCI) || defined (CONFIG_AU1X00_USB_DEVICE)
#ifdef CONFIG_PCI
// Setup PCI bus controller
au_writel(0, Au1500_PCI_CMEM);
au_writel(0x00003fff, Au1500_CFG_BASE);
#if defined(__MIPSEB__)
au_writel(0xf | (2<<6) | (1<<4), Au1500_PCI_CFG);
#else
au_writel(0xf, Au1500_PCI_CFG);
#endif
au_writel(0xf0000000, Au1500_PCI_MWMASK_DEV);
au_writel(0, Au1500_PCI_MWBASE_REV_CCL);
au_writel(0x02a00356, Au1500_PCI_STATCMD);
au_writel(0x00003c04, Au1500_PCI_HDRTYPE);
au_writel(0x00000008, Au1500_PCI_MBAR);
au_sync();
#endif
/* Enable sys bus clock divider when IDLE state or no bus activity. */
au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
/* Enable the RTC if not already enabled */
if (!(au_readl(0xac000028) & 0x20)) {
printk("enabling clock ...\n");
au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
}
/* Put the clock in BCD mode */
if (readl(0xac00002C) & 0x4) { /* reg B */
au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
au_sync();
}
}
|
