summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-omap2/prcm.c
blob: 92fc3b88a608100a07aa0a3171bf6f7543885a30 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
/*
 * linux/arch/arm/mach-omap2/prcm.c
 *
 * OMAP 24xx Power Reset and Clock Management (PRCM) functions
 *
 * Copyright (C) 2005 Nokia Corporation
 *
 * Written by Tony Lindgren <tony.lindgren@nokia.com>
 *
 * Copyright (C) 2007 Texas Instruments, Inc.
 * Rajendra Nayak <rnayak@ti.com>
 *
 * Some pieces of code Copyright (C) 2005 Texas Instruments, Inc.
 * Upgraded with OMAP4 support by Abhijit Pagare <abhijitpagare@ti.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/delay.h>
#include <linux/export.h>

#include "common.h"
#include <plat/prcm.h>

#include "soc.h"
#include "clock.h"
#include "clock2xxx.h"
#include "cm2xxx_3xxx.h"
#include "prm2xxx_3xxx.h"
#include "prm44xx.h"
#include "prminst44xx.h"
#include "cminst44xx.h"
#include "prm-regbits-24xx.h"
#include "prm-regbits-44xx.h"
#include "control.h"

void __iomem *prm_base;
void __iomem *cm_base;
void __iomem *cm2_base;
void __iomem *prcm_mpu_base;

#define MAX_MODULE_ENABLE_WAIT		100000

/* Resets clock rates and reboots the system. Only called from system.h */
void omap_prcm_restart(char mode, const char *cmd)
{
	s16 prcm_offs = 0;

	if (cpu_is_omap24xx()) {
		omap2xxx_clk_prepare_for_reboot();

		prcm_offs = WKUP_MOD;
	} else if (cpu_is_omap34xx()) {
		prcm_offs = OMAP3430_GR_MOD;
		omap3_ctrl_write_boot_mode((cmd ? (u8)*cmd : 0));
	} else if (cpu_is_omap44xx()) {
		omap4_prminst_global_warm_sw_reset(); /* never returns */
	} else {
		WARN_ON(1);
	}

	/*
	 * As per Errata i520, in some cases, user will not be able to
	 * access DDR memory after warm-reset.
	 * This situation occurs while the warm-reset happens during a read
	 * access to DDR memory. In that particular condition, DDR memory
	 * does not respond to a corrupted read command due to the warm
	 * reset occurrence but SDRC is waiting for read completion.
	 * SDRC is not sensitive to the warm reset, but the interconnect is
	 * reset on the fly, thus causing a misalignment between SDRC logic,
	 * interconnect logic and DDR memory state.
	 * WORKAROUND:
	 * Steps to perform before a Warm reset is trigged:
	 * 1. enable self-refresh on idle request
	 * 2. put SDRC in idle
	 * 3. wait until SDRC goes to idle
	 * 4. generate SW reset (Global SW reset)
	 *
	 * Steps to be performed after warm reset occurs (in bootloader):
	 * if HW warm reset is the source, apply below steps before any
	 * accesses to SDRAM:
	 * 1. Reset SMS and SDRC and wait till reset is complete
	 * 2. Re-initialize SMS, SDRC and memory
	 *
	 * NOTE: Above work around is required only if arch reset is implemented
	 * using Global SW reset(GLOBAL_SW_RST). DPLL3 reset does not need
	 * the WA since it resets SDRC as well as part of cold reset.
	 */

	/* XXX should be moved to some OMAP2/3 specific code */
	omap2_prm_set_mod_reg_bits(OMAP_RST_DPLL3_MASK, prcm_offs,
				   OMAP2_RM_RSTCTRL);
	omap2_prm_read_mod_reg(prcm_offs, OMAP2_RM_RSTCTRL); /* OCP barrier */
}

/**
 * omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness
 * @reg: physical address of module IDLEST register
 * @mask: value to mask against to determine if the module is active
 * @idlest: idle state indicator (0 or 1) for the clock
 * @name: name of the clock (for printk)
 *
 * Returns 1 if the module indicated readiness in time, or 0 if it
 * failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds.
 *
 * XXX This function is deprecated.  It should be removed once the
 * hwmod conversion is complete.
 */
int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, u8 idlest,
				const char *name)
{
	int i = 0;
	int ena = 0;

	if (idlest)
		ena = 0;
	else
		ena = mask;

	/* Wait for lock */
	omap_test_timeout(((__raw_readl(reg) & mask) == ena),
			  MAX_MODULE_ENABLE_WAIT, i);

	if (i < MAX_MODULE_ENABLE_WAIT)
		pr_debug("cm: Module associated with clock %s ready after %d loops\n",
			 name, i);
	else
		pr_err("cm: Module associated with clock %s didn't enable in %d tries\n",
		       name, MAX_MODULE_ENABLE_WAIT);

	return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0;
};

void __init omap2_set_globals_prcm(void __iomem *prm, void __iomem *cm,
				   void __iomem *cm2, void __iomem *prcm_mpu)
{
	prm_base = prm;
	cm_base = cm;
	cm2_base = cm2;
	prcm_mpu_base = prcm_mpu;

	if (cpu_is_omap44xx() || soc_is_omap54xx()) {
		omap_prm_base_init();
		omap_cm_base_init();
	}
}

/*
 * Stubbed functions so that common files continue to build when
 * custom builds are used
 * XXX These are temporary and should be removed at the earliest possible
 * opportunity
 */
int __weak omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs,
					u16 clkctrl_offs)
{
	return 0;
}

void __weak omap4_cminst_module_enable(u8 mode, u8 part, u16 inst,
				s16 cdoffs, u16 clkctrl_offs)
{
}

void __weak omap4_cminst_module_disable(u8 part, u16 inst, s16 cdoffs,
				 u16 clkctrl_offs)
{
}
OpenPOWER on IntegriCloud