summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
blob: 51f8d2eba8d8242df2373f149da35fce4275320c (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
* Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC)


Required properties:
- compatible: Should be "snps,dwc-qos-ethernet-4.10"
- reg: Address and length of the register set for the device
- clocks: Phandles to the reference clock and the bus clock
- clock-names: Should be "phy_ref_clk" for the reference clock and "apb_pclk"
  for the bus clock.
- interrupt-parent: Should be the phandle for the interrupt controller
  that services interrupts for this device
- interrupts: Should contain the core's combined interrupt signal
- phy-mode: See ethernet.txt file in the same directory

Optional properties:
- dma-coherent: Present if dma operations are coherent
- mac-address: See ethernet.txt in the same directory
- local-mac-address: See ethernet.txt in the same directory
- snps,en-lpi: If present it enables use of the AXI low-power interface
- snps,write-requests: Number of write requests that the AXI port can issue.
  It depends on the SoC configuration.
- snps,read-requests: Number of read requests that the AXI port can issue.
  It depends on the SoC configuration.
- snps,burst-map: Bitmap of allowed AXI burst lengts, with the LSB
  representing 4, then 8 etc.
- snps,txpbl: DMA Programmable burst length for the TX DMA
- snps,rxpbl: DMA Programmable burst length for the RX DMA
- snps,en-tx-lpi-clockgating: Enable gating of the MAC TX clock during
  TX low-power mode.
- phy-handle: See ethernet.txt file in the same directory
- mdio device tree subnode: When the GMAC has a phy connected to its local
    mdio, there must be device tree subnode with the following
    required properties:
    - compatible: Must be "snps,dwc-qos-ethernet-mdio".
    - #address-cells: Must be <1>.
    - #size-cells: Must be <0>.

    For each phy on the mdio bus, there must be a node with the following
    fields:

    - reg: phy id used to communicate to phy.
    - device_type: Must be "ethernet-phy".
    - fixed-mode device tree subnode: see fixed-link.txt in the same directory

Examples:
ethernet2@40010000 {
	clock-names = "phy_ref_clk", "apb_pclk";
	clocks = <&clkc 17>, <&clkc 15>;
	compatible = "snps,dwc-qos-ethernet-4.10";
	interrupt-parent = <&intc>;
	interrupts = <0x0 0x1e 0x4>;
	reg = <0x40010000 0x4000>;
	phy-handle = <&phy2>;
	phy-mode = "gmii";

	snps,en-tx-lpi-clockgating;
	snps,en-lpi;
	snps,write-requests = <2>;
	snps,read-requests = <16>;
	snps,burst-map = <0x7>;
	snps,txpbl = <8>;
	snps,rxpbl = <2>;

	dma-coherent;

	mdio {
		#address-cells = <0x1>;
		#size-cells = <0x0>;
		phy2: phy@1 {
			compatible = "ethernet-phy-ieee802.3-c22";
			device_type = "ethernet-phy";
			reg = <0x1>;
		};
	};
};
OpenPOWER on IntegriCloud