/* * This file contains work-arounds for many known PCI hardware * bugs. Devices present only on certain architectures (host * bridges et cetera) should be handled in arch-specific code. * * Note: any quirks for hotpluggable devices must _NOT_ be declared __init. * * Copyright (c) 1999 Martin Mares * * Init/reset quirks for USB host controllers should be in the * USB quirks file, where their drivers can access reuse it. * * The bridge optimization stuff has been removed. If you really * have a silly BIOS which is unable to set your host bridge right, * use the PowerTweak utility (see http://powertweak.sourceforge.net). */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include /* isa_dma_bridge_buggy */ #include "pci.h" /* * This quirk function disables memory decoding and releases memory resources * of the device specified by kernel's boot parameter 'pci=resource_alignment='. * It also rounds up size to specified alignment. * Later on, the kernel will assign page-aligned memory resource back * to the device. */ static void __devinit quirk_resource_alignment(struct pci_dev *dev) { int i; struct resource *r; resource_size_t align, size; u16 command; if (!pci_is_reassigndev(dev)) return; if (dev->hdr_type == PCI_HEADER_TYPE_NORMAL && (dev->class >> 8) == PCI_CLASS_BRIDGE_HOST) { dev_warn(&dev->dev, "Can't reassign resources to host bridge.\n"); return; } dev_info(&dev->dev, "Disabling memory decoding and releasing memory resources.\n"); pci_read_config_word(dev, PCI_COMMAND, &command); command &= ~PCI_COMMAND_MEMORY; pci_write_config_word(dev, PCI_COMMAND, command); align = pci_specified_resource_alignment(dev); for (i=0; i < PCI_BRIDGE_RESOURCES; i++) { r = &dev->resource[i]; if (!(r->flags & IORESOURCE_MEM)) continue; size = resource_size(r); if (size < align) { size = align; dev_info(&dev->dev, "Rounding up size of resource #%d to %#llx.\n", i, (unsigned long long)size); } r->end = size - 1; r->start = 0; } /* Need to disable bridge's resource window, * to enable the kernel to reassign new resource * window later on. */ if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE && (dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) { for (i = PCI_BRIDGE_RESOURCES; i < PCI_NUM_RESOURCES; i++) { r = &dev->resource[i]; if (!(r->flags & IORESOURCE_MEM)) continue; r->end = resource_size(r) - 1; r->start = 0; } pci_disable_bridge_window(dev); } } DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_resource_alignment); /* * Decoding should be disabled for a PCI device during BAR sizing to avoid * conflict. But doing so may cause problems on host bridge and perhaps other * key system devices. For devices that need to have mmio decoding always-on, * we need to set the dev->mmio_always_on bit. */ static void __devinit quirk_mmio_always_on(struct pci_dev *dev) { if ((dev->class >> 8) == PCI_CLASS_BRIDGE_HOST) dev->mmio_always_on = 1; } DECLARE_PCI_FIXUP_EARLY(PCI_ANY_ID, PCI_ANY_ID, quirk_mmio_always_on); /* The Mellanox Tavor device gives false positive parity errors * Mark this device with a broken_parity_status, to allow * PCI scanning code to "skip" this now blacklisted device. */ static void __devinit quirk_mellanox_tavor(struct pci_dev *dev) { dev->broken_parity_status = 1; /* This device gives false positives */ } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX,PCI_DEVICE_ID_MELLANOX_TAVOR,quirk_mellanox_tavor); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_MELLANOX,PCI_DEVICE_ID_MELLANOX_TAVOR_BRIDGE,quirk_mellanox_tavor); /* Deal with broken BIOS'es that neglect to enable passive release, which can cause problems in combination with the 82441FX/PPro MTRRs */ static void quirk_passive_release(struct pci_dev *dev) { struct pci_dev *d = NULL; unsigned char dlc; /* We have to make sure a particular bit is set in the PIIX3 ISA bridge, so we have to go out and find it. */ while ((d = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, d))) { pci_read_config_byte(d, 0x82, &dlc); if (!(dlc & 1<<1)) { dev_info(&d->dev, "PIIX3: Enabling Passive Release\n"); dlc |= 1<<1; pci_write_config_byte(d, 0x82, dlc); } } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_passive_release); /* The VIA VP2/VP3/MVP3 seem to have some 'features'. There may be a workaround but VIA don't answer queries. If you happen to have good contacts at VIA ask them for me please -- Alan This appears to be BIOS not version dependent. So presumably there is a chipset level fix */ static void __devinit quirk_isa_dma_hangs(struct pci_dev *dev) { if (!isa_dma_bridge_buggy) { isa_dma_bridge_buggy=1; dev_info(&dev->dev, "Activating ISA DMA hang workarounds\n"); } } /* * Its not totally clear which chipsets are the problematic ones * We know 82C586 and 82C596 variants are affected. */ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0, quirk_isa_dma_hangs); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C596, quirk_isa_dma_hangs); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_0, quirk_isa_dma_hangs); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, quirk_isa_dma_hangs); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_1, quirk_isa_dma_hangs); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_2, quirk_isa_dma_hangs); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_CBUS_3, quirk_isa_dma_hangs); /* * Intel NM10 "TigerPoint" LPC PM1a_STS.BM_STS must be clear * for some HT machines to use C4 w/o hanging. */ static void __devinit quirk_tigerpoint_bm_sts(struct pci_dev *dev) { u32 pmbase; u16 pm1a; pci_read_config_dword(dev, 0x40, &pmbase); pmbase = pmbase & 0xff80; pm1a = inw(pmbase); if (pm1a & 0x10) { dev_info(&dev->dev, FW_BUG "TigerPoint LPC.BM_STS cleared\n"); outw(0x10, pmbase); } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_TGP_LPC, quirk_tigerpoint_bm_sts); /* * Chipsets where PCI->PCI transfers vanish or hang */ static void __devinit quirk_nopcipci(struct pci_dev *dev) { if ((pci_pci_problems & PCIPCI_FAIL)==0) { dev_info(&dev->dev, "Disabling direct PCI/PCI transfers\n"); pci_pci_problems |= PCIPCI_FAIL; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, quirk_nopcipci); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_496, quirk_nopcipci); static void __devinit quirk_nopciamd(struct pci_dev *dev) { u8 rev; pci_read_config_byte(dev, 0x08, &rev); if (rev == 0x13) { /* Erratum 24 */ dev_info(&dev->dev, "Chipset erratum: Disabling direct PCI/AGP transfers\n"); pci_pci_problems |= PCIAGP_FAIL; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8151_0, quirk_nopciamd); /* * Triton requires workarounds to be used by the drivers */ static void __devinit quirk_triton(struct pci_dev *dev) { if ((pci_pci_problems&PCIPCI_TRITON)==0) { dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n"); pci_pci_problems |= PCIPCI_TRITON; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437, quirk_triton); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82437VX, quirk_triton); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439, quirk_triton); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82439TX, quirk_triton); /* * VIA Apollo KT133 needs PCI latency patch * Made according to a windows driver based patch by George E. Breese * see PCI Latency Adjust on http://www.viahardware.com/download/viatweak.shtm * and http://www.georgebreese.com/net/software/#PCI * Also see http://www.au-ja.org/review-kt133a-1-en.phtml for * the info on which Mr Breese based his work. * * Updated based on further information from the site and also on * information provided by VIA */ static void quirk_vialatency(struct pci_dev *dev) { struct pci_dev *p; u8 busarb; /* Ok we have a potential problem chipset here. Now see if we have a buggy southbridge */ p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, NULL); if (p!=NULL) { /* 0x40 - 0x4f == 686B, 0x10 - 0x2f == 686A; thanks Dan Hollis */ /* Check for buggy part revisions */ if (p->revision < 0x40 || p->revision > 0x42) goto exit; } else { p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, NULL); if (p==NULL) /* No problem parts */ goto exit; /* Check for buggy part revisions */ if (p->revision < 0x10 || p->revision > 0x12) goto exit; } /* * Ok we have the problem. Now set the PCI master grant to * occur every master grant. The apparent bug is that under high * PCI load (quite common in Linux of course) you can get data * loss when the CPU is held off the bus for 3 bus master requests * This happens to include the IDE controllers.... * * VIA only apply this fix when an SB Live! is present but under * both Linux and Windows this isn't enough, and we have seen * corruption without SB Live! but with things like 3 UDMA IDE * controllers. So we ignore that bit of the VIA recommendation.. */ pci_read_config_byte(dev, 0x76, &busarb); /* Set bit 4 and bi 5 of byte 76 to 0x01 "Master priority rotation on every PCI master grant */ busarb &= ~(1<<5); busarb |= (1<<4); pci_write_config_byte(dev, 0x76, busarb); dev_info(&dev->dev, "Applying VIA southbridge workaround\n"); exit: pci_dev_put(p); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency); /* Must restore this on a resume from RAM */ DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, quirk_vialatency); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8371_1, quirk_vialatency); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, quirk_vialatency); /* * VIA Apollo VP3 needs ETBF on BT848/878 */ static void __devinit quirk_viaetbf(struct pci_dev *dev) { if ((pci_pci_problems&PCIPCI_VIAETBF)==0) { dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n"); pci_pci_problems |= PCIPCI_VIAETBF; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_viaetbf); static void __devinit quirk_vsfx(struct pci_dev *dev) { if ((pci_pci_problems&PCIPCI_VSFX)==0) { dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n"); pci_pci_problems |= PCIPCI_VSFX; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576, quirk_vsfx); /* * Ali Magik requires workarounds to be used by the drivers * that DMA to AGP space. Latency must be set to 0xA and triton * workaround applied too * [Info kindly provided by ALi] */ static void __init quirk_alimagik(struct pci_dev *dev) { if ((pci_pci_problems&PCIPCI_ALIMAGIK)==0) { dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n"); pci_pci_problems |= PCIPCI_ALIMAGIK|PCIPCI_TRITON; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1647, quirk_alimagik); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1651, quirk_alimagik); /* * Natoma has some interesting boundary conditions with Zoran stuff * at least */ static void __devinit quirk_natoma(struct pci_dev *dev) { if ((pci_pci_problems&PCIPCI_NATOMA)==0) { dev_info(&dev->dev, "Limiting direct PCI/PCI transfers\n"); pci_pci_problems |= PCIPCI_NATOMA; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82441, quirk_natoma); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_0, quirk_natoma); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443LX_1, quirk_natoma); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_0, quirk_natoma); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_1, quirk_natoma); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443BX_2, quirk_natoma); /* * This chip can cause PCI parity errors if config register 0xA0 is read * while DMAs are occurring. */ static void __devinit quirk_citrine(struct pci_dev *dev) { dev->cfg_size = 0xA0; } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_CITRINE, quirk_citrine); /* * S3 868 and 968 chips report region size equal to 32M, but they decode 64M. * If it's needed, re-allocate the region. */ static void __devinit quirk_s3_64M(struct pci_dev *dev) { struct resource *r = &dev->resource[0]; if ((r->start & 0x3ffffff) || r->end != r->start + 0x3ffffff) { r->start = 0; r->end = 0x3ffffff; } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M); /* * Some CS5536 BIOSes (for example, the Soekris NET5501 board w/ comBIOS * ver. 1.33 20070103) don't set the correct ISA PCI region header info. * BAR0 should be 8 bytes; instead, it may be set to something like 8k * (which conflicts w/ BAR1's memory range). */ static void __devinit quirk_cs5536_vsa(struct pci_dev *dev) { if (pci_resource_len(dev, 0) != 8) { struct resource *res = &dev->resource[0]; res->end = res->start + 8 - 1; dev_info(&dev->dev, "CS5536 ISA bridge bug detected " "(incorrect header); workaround applied.\n"); } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, quirk_cs5536_vsa); static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region, unsigned size, int nr, const char *name) { region &= ~(size-1); if (region) { struct pci_bus_region bus_region; struct resource *res = dev->resource + nr; res->name = pci_name(dev); res->start = region; res->end = region + size - 1; res->flags = IORESOURCE_IO; /* Convert from PCI bus to resource space. */ bus_region.start = res->start; bus_region.end = res->end; pcibios_bus_to_resource(dev, res, &bus_region); if (pci_claim_resource(dev, nr) == 0) dev_info(&dev->dev, "quirk: %pR claimed by %s\n", res, name); } } /* * ATI Northbridge setups MCE the processor if you even * read somewhere between 0x3b0->0x3bb or read 0x3d3 */ static void __devinit quirk_ati_exploding_mce(struct pci_dev *dev) { dev_info(&dev->dev, "ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb\n"); /* Mae rhaid i ni beidio ag edrych ar y lleoliadiau I/O hyn */ request_region(0x3b0, 0x0C, "RadeonIGP"); request_region(0x3d3, 0x01, "RadeonIGP"); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS100, quirk_ati_exploding_mce); /* * Let's make the southbridge information explicit instead * of having to worry about people probing the ACPI areas, * for example.. (Yes, it happens, and if you read the wrong * ACPI register it will put the machine to sleep with no * way of waking it up again. Bummer). * * ALI M7101: Two IO regions pointed to by words at * 0xE0 (64 bytes of ACPI registers) * 0xE2 (32 bytes of SMB registers) */ static void __devinit quirk_ali7101_acpi(struct pci_dev *dev) { u16 region; pci_read_config_word(dev, 0xE0, ®ion); quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "ali7101 ACPI"); pci_read_config_word(dev, 0xE2, ®ion); quirk_io_region(dev, region, 32, PCI_BRIDGE_RESOURCES+1, "ali7101 SMB"); } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101, quirk_ali7101_acpi); static void piix4_io_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) { u32 devres; u32 mask, size, base; pci_read_config_dword(dev, port, &devres); if ((devres & enable) != enable) return; mask = (devres >> 16) & 15; base = devres & 0xffff; size = 16; for (;;) { unsigned bit = size >> 1; if ((bit & mask) == bit) break; size = bit; } /* * For now we only print it out. Eventually we'll want to * reserve it (at least if it's in the 0x1000+ range), but * let's get enough confirmation reports first. */ base &= -size; dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, base + size - 1); } static void piix4_mem_quirk(struct pci_dev *dev, const char *name, unsigned int port, unsigned int enable) { u32 devres; u32 mask, size, base; pci_read_config_dword(dev, port, &devres); if ((devres & enable) != enable) return; base = devres & 0xffff0000; mask = (devres & 0x3f) << 16; size = 128 << 16; for (;;) { unsigned bit = size >> 1; if ((bit & mask) == bit) break; size = bit; } /* * For now we only print it out. Eventually we'll want to * reserve it, but let's get enough confirmation reports first. */ base &= -size; dev_info(&dev->dev, "%s MMIO at %04x-%04x\n", name, base, base + size - 1); } /* * PIIX4 ACPI: Two IO regions pointed to by longwords at * 0x40 (64 bytes of ACPI registers) * 0x90 (16 bytes of SMB registers) * and a few strange programmable PIIX4 device resources. */ static void __devinit quirk_piix4_acpi(struct pci_dev *dev) { u32 region, res_a; pci_read_config_dword(dev, 0x40, ®ion); quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES, "PIIX4 ACPI"); pci_read_config_dword(dev, 0x90, ®ion); quirk_io_region(dev, region, 16, PCI_BRIDGE_RESOURCES+1, "PIIX4 SMB"); /* Device resource A has enables for some of the other ones */ pci_read_config_dword(dev, 0x5c, &res_a); piix4_io_quirk(dev, "PIIX4 devres B", 0x60, 3 << 21); piix4_io_quirk(dev, "PIIX4 devres C", 0x64, 3 << 21); /* Device resource D is just bitfields for static resources */ /* Device 12 enabled? */ if (res_a & (1 << 29)) { piix4_io_quirk(dev, "PIIX4 devres E", 0x68, 1 << 20); piix4_mem_quirk(dev, "PIIX4 devres F", 0x6c, 1 << 7); } /* Device 13 enabled? */ if (res_a & (1 << 30)) { piix4_io_quirk(dev, "PIIX4 devres G", 0x70, 1 << 20); piix4_mem_quirk(dev, "PIIX4 devres H", 0x74, 1 << 7); } piix4_io_quirk(dev, "PIIX4 devres I", 0x78, 1 << 20); piix4_io_quirk(dev, "PIIX4 devres J", 0x7c, 1 << 20); } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, quirk_piix4_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_3, quirk_piix4_acpi); #define ICH_PMBASE 0x40 #define ICH_ACPI_CNTL 0x44 #define ICH4_ACPI_EN 0x10 #define ICH6_ACPI_EN 0x80 #define ICH4_GPIOBASE 0x58 #define ICH4_GPIO_CNTL 0x5c #define ICH4_GPIO_EN 0x10 #define ICH6_GPIOBASE 0x48 #define ICH6_GPIO_CNTL 0x4c #define ICH6_GPIO_EN 0x10 /* * ICH4, ICH4-M, ICH5, ICH5-M ACPI: Three IO regions pointed to by longwords at * 0x40 (128 bytes of ACPI, GPIO & TCO registers) * 0x58 (64 bytes of GPIO I/O space) */ static void __devinit quirk_ich4_lpc_acpi(struct pci_dev *dev) { u32 region; u8 enable; /* * The check for PCIBIOS_MIN_IO is to ensure we won't create a conflict * with low legacy (and fixed) ports. We don't know the decoding * priority and can't tell whether the legacy device or the one created * here is really at that address. This happens on boards with broken * BIOSes. */ pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable); if (enable & ICH4_ACPI_EN) { pci_read_config_dword(dev, ICH_PMBASE, ®ion); region &= PCI_BASE_ADDRESS_IO_MASK; if (region >= PCIBIOS_MIN_IO) quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES, "ICH4 ACPI/GPIO/TCO"); } pci_read_config_byte(dev, ICH4_GPIO_CNTL, &enable); if (enable & ICH4_GPIO_EN) { pci_read_config_dword(dev, ICH4_GPIOBASE, ®ion); region &= PCI_BASE_ADDRESS_IO_MASK; if (region >= PCIBIOS_MIN_IO) quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES + 1, "ICH4 GPIO"); } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, quirk_ich4_lpc_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_0, quirk_ich4_lpc_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, quirk_ich4_lpc_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_10, quirk_ich4_lpc_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, quirk_ich4_lpc_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, quirk_ich4_lpc_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, quirk_ich4_lpc_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, quirk_ich4_lpc_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, quirk_ich4_lpc_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1, quirk_ich4_lpc_acpi); static void __devinit ich6_lpc_acpi_gpio(struct pci_dev *dev) { u32 region; u8 enable; pci_read_config_byte(dev, ICH_ACPI_CNTL, &enable); if (enable & ICH6_ACPI_EN) { pci_read_config_dword(dev, ICH_PMBASE, ®ion); region &= PCI_BASE_ADDRESS_IO_MASK; if (region >= PCIBIOS_MIN_IO) quirk_io_region(dev, region, 128, PCI_BRIDGE_RESOURCES, "ICH6 ACPI/GPIO/TCO"); } pci_read_config_byte(dev, ICH6_GPIO_CNTL, &enable); if (enable & ICH6_GPIO_EN) { pci_read_config_dword(dev, ICH6_GPIOBASE, ®ion); region &= PCI_BASE_ADDRESS_IO_MASK; if (region >= PCIBIOS_MIN_IO) quirk_io_region(dev, region, 64, PCI_BRIDGE_RESOURCES + 1, "ICH6 GPIO"); } } static void __devinit ich6_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name, int dynsize) { u32 val; u32 size, base; pci_read_config_dword(dev, reg, &val); /* Enabled? */ if (!(val & 1)) return; base = val & 0xfffc; if (dynsize) { /* * This is not correct. It is 16, 32 or 64 bytes depending on * register D31:F0:ADh bits 5:4. * * But this gets us at least _part_ of it. */ size = 16; } else { size = 128; } base &= ~(size-1); /* Just print it out for now. We should reserve it after more debugging */ dev_info(&dev->dev, "%s PIO at %04x-%04x\n", name, base, base+size-1); } static void __devinit quirk_ich6_lpc(struct pci_dev *dev) { /* Shared ACPI/GPIO decode with all ICH6+ */ ich6_lpc_acpi_gpio(dev); /* ICH6-specific generic IO decode */ ich6_lpc_generic_decode(dev, 0x84, "LPC Generic IO decode 1", 0); ich6_lpc_generic_decode(dev, 0x88, "LPC Generic IO decode 2", 1); } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_0, quirk_ich6_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, quirk_ich6_lpc); static void __devinit ich7_lpc_generic_decode(struct pci_dev *dev, unsigned reg, const char *name) { u32 val; u32 mask, base; pci_read_config_dword(dev, reg, &val); /* Enabled? */ if (!(val & 1)) return; /* * IO base in bits 15:2, mask in bits 23:18, both * are dword-based */ base = val & 0xfffc; mask = (val >> 16) & 0xfc; mask |= 3; /* Just print it out for now. We should reserve it after more debugging */ dev_info(&dev->dev, "%s PIO at %04x (mask %04x)\n", name, base, mask); } /* ICH7-10 has the same common LPC generic IO decode registers */ static void __devinit quirk_ich7_lpc(struct pci_dev *dev) { /* We share the common ACPI/GPIO decode with ICH6 */ ich6_lpc_acpi_gpio(dev); /* And have 4 ICH7+ generic decodes */ ich7_lpc_generic_decode(dev, 0x84, "ICH7 LPC Generic IO decode 1"); ich7_lpc_generic_decode(dev, 0x88, "ICH7 LPC Generic IO decode 2"); ich7_lpc_generic_decode(dev, 0x8c, "ICH7 LPC Generic IO decode 3"); ich7_lpc_generic_decode(dev, 0x90, "ICH7 LPC Generic IO decode 4"); } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_31, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_4, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_2, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_4, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_7, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_8, quirk_ich7_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH10_1, quirk_ich7_lpc); /* * VIA ACPI: One IO region pointed to by longword at * 0x48 or 0x20 (256 bytes of ACPI registers) */ static void __devinit quirk_vt82c586_acpi(struct pci_dev *dev) { u32 region; if (dev->revision & 0x10) { pci_read_config_dword(dev, 0x48, ®ion); region &= PCI_BASE_ADDRESS_IO_MASK; quirk_io_region(dev, region, 256, PCI_BRIDGE_RESOURCES, "vt82c586 ACPI"); } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_vt82c586_acpi); /* * VIA VT82C686 ACPI: Three IO region pointed to by (long)words at * 0x48 (256 bytes of ACPI registers) * 0x70 (128 bytes of hardware monitoring register) * 0x90 (16 bytes of SMB registers) */ static void __devinit quirk_vt82c686_acpi(struct pci_dev *dev) { u16 hm; u32 smb; quirk_vt82c586_acpi(dev); pci_read_config_word(dev, 0x70, &hm); hm &= PCI_BASE_ADDRESS_IO_MASK; quirk_io_region(dev, hm, 128, PCI_BRIDGE_RESOURCES + 1, "vt82c686 HW-mon"); pci_read_config_dword(dev, 0x90, &smb); smb &= PCI_BASE_ADDRESS_IO_MASK; quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 2, "vt82c686 SMB"); } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_vt82c686_acpi); /* * VIA VT8235 ISA Bridge: Two IO regions pointed to by words at * 0x88 (128 bytes of power management registers) * 0xd0 (16 bytes of SMB registers) */ static void __devinit quirk_vt8235_acpi(struct pci_dev *dev) { u16 pm, smb; pci_read_config_word(dev, 0x88, &pm); pm &= PCI_BASE_ADDRESS_IO_MASK; quirk_io_region(dev, pm, 128, PCI_BRIDGE_RESOURCES, "vt8235 PM"); pci_read_config_word(dev, 0xd0, &smb); smb &= PCI_BASE_ADDRESS_IO_MASK; quirk_io_region(dev, smb, 16, PCI_BRIDGE_RESOURCES + 1, "vt8235 SMB"); } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_vt8235_acpi); /* * TI XIO2000a PCIe-PCI Bridge erroneously reports it supports fast back-to-back: * Disable fast back-to-back on the secondary bus segment */ static void __devinit quirk_xio2000a(struct pci_dev *dev) { struct pci_dev *pdev; u16 command; dev_warn(&dev->dev, "TI XIO2000a quirk detected; " "secondary bus fast back-to-back transfers disabled\n"); list_for_each_entry(pdev, &dev->subordinate->devices, bus_list) { pci_read_config_word(pdev, PCI_COMMAND, &command); if (command & PCI_COMMAND_FAST_BACK) pci_write_config_word(pdev, PCI_COMMAND, command & ~PCI_COMMAND_FAST_BACK); } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_XIO2000A, quirk_xio2000a); #ifdef CONFIG_X86_IO_APIC #include /* * VIA 686A/B: If an IO-APIC is active, we need to route all on-chip * devices to the external APIC. * * TODO: When we have device-specific interrupt routers, * this code will go away from quirks. */ static void quirk_via_ioapic(struct pci_dev *dev) { u8 tmp; if (nr_ioapics < 1) tmp = 0; /* nothing routed to external APIC */ else tmp = 0x1f; /* all known bits (4-0) routed to external APIC */ dev_info(&dev->dev, "%sbling VIA external APIC routing\n", tmp == 0 ? "Disa" : "Ena"); /* Offset 0x58: External APIC IRQ output control */ pci_write_config_byte (dev, 0x58, tmp); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_ioapic); /* * VIA 8237: Some BIOSs don't set the 'Bypass APIC De-Assert Message' Bit. * This leads to doubled level interrupt rates. * Set this bit to get rid of cycle wastage. * Otherwise uncritical. */ static void quirk_via_vt8237_bypass_apic_deassert(struct pci_dev *dev) { u8 misc_control2; #define BYPASS_APIC_DEASSERT 8 pci_read_config_byte(dev, 0x5B, &misc_control2); if (!(misc_control2 & BYPASS_APIC_DEASSERT)) { dev_info(&dev->dev, "Bypassing VIA 8237 APIC De-Assert Message\n"); pci_write_config_byte(dev, 0x5B, misc_control2|BYPASS_APIC_DEASSERT); } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_vt8237_bypass_apic_deassert); /* * The AMD io apic can hang the box when an apic irq is masked. * We check all revs >= B0 (yet not in the pre production!) as the bug * is currently marked NoFix * * We have multiple reports of hangs with this chipset that went away with * noapic specified. For the moment we assume it's the erratum. We may be wrong * of course. However the advice is demonstrably good even if so.. */ static void __devinit quirk_amd_ioapic(struct pci_dev *dev) { if (dev->revision >= 0x02) { dev_warn(&dev->dev, "I/O APIC: AMD Erratum #22 may be present. In the event of instability try\n"); dev_warn(&dev->dev, " : booting with the \"noapic\" option\n"); } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7410, quirk_amd_ioapic); static void __init quirk_ioapic_rmw(struct pci_dev *dev) { if (dev->devfn == 0 && dev->bus->number == 0) sis_apic_bug = 1; } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SI, PCI_ANY_ID, quirk_ioapic_rmw); #endif /* CONFIG_X86_IO_APIC */ /* * Some settings of MMRBC can lead to data corruption so block changes. * See AMD 8131 HyperTransport PCI-X Tunnel Revision Guide */ static void __init quirk_amd_8131_mmrbc(struct pci_dev *dev) { if (dev->subordinate && dev->revision <= 0x12) { dev_info(&dev->dev, "AMD8131 rev %x detected; " "disabling PCI-X MMRBC\n", dev->revision); dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MMRBC; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_amd_8131_mmrbc); /* * FIXME: it is questionable that quirk_via_acpi * is needed. It shows up as an ISA bridge, and does not * support the PCI_INTERRUPT_LINE register at all. Therefore * it seems like setting the pci_dev's 'irq' to the * value of the ACPI SCI interrupt is only done for convenience. * -jgarzik */ static void __devinit quirk_via_acpi(struct pci_dev *d) { /* * VIA ACPI device: SCI IRQ line in PCI config byte 0x42 */ u8 irq; pci_read_config_byte(d, 0x42, &irq); irq &= 0xf; if (irq && (irq != 2)) d->irq = irq; } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi); /* * VIA bridges which have VLink */ static int via_vlink_dev_lo = -1, via_vlink_dev_hi = 18; static void quirk_via_bridge(struct pci_dev *dev) { /* See what bridge we have and find the device ranges */ switch (dev->device) { case PCI_DEVICE_ID_VIA_82C686: /* The VT82C686 is special, it attaches to PCI and can have any device number. All its subdevices are functions of that single device. */ via_vlink_dev_lo = PCI_SLOT(dev->devfn); via_vlink_dev_hi = PCI_SLOT(dev->devfn); break; case PCI_DEVICE_ID_VIA_8237: case PCI_DEVICE_ID_VIA_8237A: via_vlink_dev_lo = 15; break; case PCI_DEVICE_ID_VIA_8235: via_vlink_dev_lo = 16; break; case PCI_DEVICE_ID_VIA_8231: case PCI_DEVICE_ID_VIA_8233_0: case PCI_DEVICE_ID_VIA_8233A: case PCI_DEVICE_ID_VIA_8233C_0: via_vlink_dev_lo = 17; break; } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686, quirk_via_bridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8231, quirk_via_bridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233_0, quirk_via_bridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233A, quirk_via_bridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8233C_0, quirk_via_bridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235, quirk_via_bridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, quirk_via_bridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237A, quirk_via_bridge); /** * quirk_via_vlink - VIA VLink IRQ number update * @dev: PCI device * * If the device we are dealing with is on a PIC IRQ we need to * ensure that the IRQ line register which usually is not relevant * for PCI cards, is actually written so that interrupts get sent * to the right place. * We only do this on systems where a VIA south bridge was detected, * and only for VIA devices on the motherboard (see quirk_via_bridge * above). */ static void quirk_via_vlink(struct pci_dev *dev) { u8 irq, new_irq; /* Check if we have VLink at all */ if (via_vlink_dev_lo == -1) return; new_irq = dev->irq; /* Don't quirk interrupts outside the legacy IRQ range */ if (!new_irq || new_irq > 15) return; /* Internal device ? */ if (dev->bus->number != 0 || PCI_SLOT(dev->devfn) > via_vlink_dev_hi || PCI_SLOT(dev->devfn) < via_vlink_dev_lo) return; /* This is an internal VLink device on a PIC interrupt. The BIOS ought to have set this but may not have, so we redo it */ pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq); if (new_irq != irq) { dev_info(&dev->dev, "VIA VLink IRQ fixup, from %d to %d\n", irq, new_irq); udelay(15); /* unknown if delay really needed */ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); } } DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_vlink); /* * VIA VT82C598 has its device ID settable and many BIOSes * set it to the ID of VT82C597 for backward compatibility. * We need to switch it off to be able to recognize the real * type of the chip. */ static void __devinit quirk_vt82c598_id(struct pci_dev *dev) { pci_write_config_byte(dev, 0xfc, 0); pci_read_config_word(dev, PCI_DEVICE_ID, &dev->device); } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C597_0, quirk_vt82c598_id); /* * CardBus controllers have a legacy base address that enables them * to respond as i82365 pcmcia controllers. We don't want them to * do this even if the Linux CardBus driver is not loaded, because * the Linux i82365 driver does not (and should not) handle CardBus. */ static void quirk_cardbus_legacy(struct pci_dev *dev) { if ((PCI_CLASS_BRIDGE_CARDBUS << 8) ^ dev->class) return; pci_write_config_dword(dev, PCI_CB_LEGACY_MODE_BASE, 0); } DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, quirk_cardbus_legacy); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_ANY_ID, PCI_ANY_ID, quirk_cardbus_legacy); /* * Following the PCI ordering rules is optional on the AMD762. I'm not * sure what the designers were smoking but let's not inhale... * * To be fair to AMD, it follows the spec by default, its BIOS people * who turn it off! */ static void quirk_amd_ordering(struct pci_dev *dev) { u32 pcic; pci_read_config_dword(dev, 0x4C, &pcic); if ((pcic&6)!=6) { pcic |= 6; dev_warn(&dev->dev, "BIOS failed to enable PCI standards compliance; fixing this error\n"); pci_write_config_dword(dev, 0x4C, pcic); pci_read_config_dword(dev, 0x84, &pcic); pcic |= (1<<23); /* Required in this mode */ pci_write_config_dword(dev, 0x84, pcic); } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_FE_GATE_700C, quirk_amd_ordering); /* * DreamWorks provided workaround for Dunord I-3000 problem * * This card decodes and responds to addresses not apparently * assigned to it. We force a larger allocation to ensure that * nothing gets put too close to it. */ static void __devinit quirk_dunord ( struct pci_dev * dev ) { struct resource *r = &dev->resource [1]; r->start = 0; r->end = 0xffffff; } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_DUNORD, PCI_DEVICE_ID_DUNORD_I3000, quirk_dunord); /* * i82380FB mobile docking controller: its PCI-to-PCI bridge * is subtractive decoding (transparent), and does indicate this * in the ProgIf. Unfortunately, the ProgIf value is wrong - 0x80 * instead of 0x01. */ static void __devinit quirk_transparent_bridge(struct pci_dev *dev) { dev->transparent = 1; } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82380FB, quirk_transparent_bridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA, 0x605, quirk_transparent_bridge); /* * Common misconfiguration of the MediaGX/Geode PCI master that will * reduce PCI bandwidth from 70MB/s to 25MB/s. See the GXM/GXLV/GX1 * datasheets found at http://www.national.com/analog for info on what * these bits do. */ static void quirk_mediagx_master(struct pci_dev *dev) { u8 reg; pci_read_config_byte(dev, 0x41, ®); if (reg & 2) { reg &= ~2; dev_info(&dev->dev, "Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x%02x)\n", reg); pci_write_config_byte(dev, 0x41, reg); } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master); /* * Ensure C0 rev restreaming is off. This is normally done by * the BIOS but in the odd case it is not the results are corruption * hence the presence of a Linux check */ static void quirk_disable_pxb(struct pci_dev *pdev) { u16 config; if (pdev->revision != 0x04) /* Only C0 requires this */ return; pci_read_config_word(pdev, 0x40, &config); if (config & (1<<6)) { config &= ~(1<<6); pci_write_config_word(pdev, 0x40, config); dev_info(&pdev->dev, "C0 revision 450NX. Disabling PCI restreaming\n"); } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, quirk_disable_pxb); static void __devinit quirk_amd_ide_mode(struct pci_dev *pdev) { /* set SBX00/Hudson-2 SATA in IDE mode to AHCI mode */ u8 tmp; pci_read_config_byte(pdev, PCI_CLASS_DEVICE, &tmp); if (tmp == 0x01) { pci_read_config_byte(pdev, 0x40, &tmp); pci_write_config_byte(pdev, 0x40, tmp|1); pci_write_config_byte(pdev, 0x9, 1); pci_write_config_byte(pdev, 0xa, 6); pci_write_config_byte(pdev, 0x40, tmp); pdev->class = PCI_CLASS_STORAGE_SATA_AHCI; dev_info(&pdev->dev, "set SATA to AHCI mode\n"); } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, quirk_amd_ide_mode); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP700_SATA, quirk_amd_ide_mode); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_HUDSON2_SATA_IDE, quirk_amd_ide_mode); /* * Serverworks CSB5 IDE does not fully support native mode */ static void __devinit quirk_svwks_csb5ide(struct pci_dev *pdev) { u8 prog; pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); if (prog & 5) { prog &= ~5; pdev->class &= ~5; pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); /* PCI layer will sort out resources */ } } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide); /* * Intel 82801CAM ICH3-M datasheet says IDE modes must be the same */ static void __init quirk_ide_samemode(struct pci_dev *pdev) { u8 prog; pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog); if (((prog & 1) && !(prog & 4)) || ((prog & 4) && !(prog & 1))) { dev_info(&pdev->dev, "IDE mode mismatch; forcing legacy mode\n"); prog &= ~5; pdev->class &= ~5; pci_write_config_byte(pdev, PCI_CLASS_PROG, prog); } } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode); /* * Some ATA devices break if put into D3 */ static void __devinit quirk_no_ata_d3(struct pci_dev *pdev) { /* Quirk the legacy ATA devices only. The AHCI ones are ok */ if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) pdev->dev_flags |= PCI_DEV_FLAGS_NO_D3; } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_ANY_ID, quirk_no_ata_d3); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ATI, PCI_ANY_ID, quirk_no_ata_d3); /* ALi loses some register settings that we cannot then restore */ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, quirk_no_ata_d3); /* VIA comes back fine but we need to keep it alive or ACPI GTM failures occur when mode detecting */ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_no_ata_d3); /* This was originally an Alpha specific thing, but it really fits here. * The i82375 PCI/EISA bridge appears as non-classified. Fix that. */ static void __init quirk_eisa_bridge(struct pci_dev *dev) { dev->class = PCI_CLASS_BRIDGE_EISA << 8; } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82375, quirk_eisa_bridge); /* * On ASUS P4B boards, the SMBus PCI Device within the ICH2/4 southbridge * is not activated. The myth is that Asus said that they do not want the * users to be irritated by just another PCI Device in the Win98 device * manager. (see the file prog/hotplug/README.p4b in the lm_sensors * package 2.7.0 for details) * * The SMBus PCI Device can be activated by setting a bit in the ICH LPC * bridge. Unfortunately, this device has no subvendor/subdevice ID. So it * becomes necessary to do this tweak in two steps -- the chosen trigger * is either the Host bridge (preferred) or on-board VGA controller. * * Note that we used to unhide the SMBus that way on Toshiba laptops * (Satellite A40 and Tecra M2) but then found that the thermal management * was done by SMM code, which could cause unsynchronized concurrent * accesses to the SMBus registers, with potentially bad effects. Thus you * should be very careful when adding new entries: if SMM is accessing the * Intel SMBus, this is a very good reason to leave it hidden. * * Likewise, many recent laptops use ACPI for thermal management. If the * ACPI DSDT code accesses the SMBus, then Linux should not access it * natively, and keeping the SMBus hidden is the right thing to do. If you * are about to add an entry in the table below, please first disassemble * the DSDT and double-check that there is no code accessing the SMBus. */ static int asus_hides_smbus; static void __init asus_hides_smbus_hostbridge(struct pci_dev *dev) { if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { if (dev->device == PCI_DEVICE_ID_INTEL_82845_HB) switch(dev->subsystem_device) { case 0x8025: /* P4B-LX */ case 0x8070: /* P4B */ case 0x8088: /* P4B533 */ case 0x1626: /* L3C notebook */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82845G_HB) switch(dev->subsystem_device) { case 0x80b1: /* P4GE-V */ case 0x80b2: /* P4PE */ case 0x8093: /* P4B533-V */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82850_HB) switch(dev->subsystem_device) { case 0x8030: /* P4T533 */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_7205_0) switch (dev->subsystem_device) { case 0x8070: /* P4G8X Deluxe */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_E7501_MCH) switch (dev->subsystem_device) { case 0x80c9: /* PU-DLS */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82855GM_HB) switch (dev->subsystem_device) { case 0x1751: /* M2N notebook */ case 0x1821: /* M5N notebook */ case 0x1897: /* A6L notebook */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) switch (dev->subsystem_device) { case 0x184b: /* W1N notebook */ case 0x186a: /* M6Ne notebook */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB) switch (dev->subsystem_device) { case 0x80f2: /* P4P800-X */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82915GM_HB) switch (dev->subsystem_device) { case 0x1882: /* M6V notebook */ case 0x1977: /* A6VA notebook */ asus_hides_smbus = 1; } } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_HP)) { if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) switch(dev->subsystem_device) { case 0x088C: /* HP Compaq nc8000 */ case 0x0890: /* HP Compaq nc6000 */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82865_HB) switch (dev->subsystem_device) { case 0x12bc: /* HP D330L */ case 0x12bd: /* HP D530 */ case 0x006a: /* HP Compaq nx9500 */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82875_HB) switch (dev->subsystem_device) { case 0x12bf: /* HP xw4100 */ asus_hides_smbus = 1; } } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG)) { if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) switch(dev->subsystem_device) { case 0xC00C: /* Samsung P35 notebook */ asus_hides_smbus = 1; } } else if (unlikely(dev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ)) { if (dev->device == PCI_DEVICE_ID_INTEL_82855PM_HB) switch(dev->subsystem_device) { case 0x0058: /* Compaq Evo N620c */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82810_IG3) switch(dev->subsystem_device) { case 0xB16C: /* Compaq Deskpro EP 401963-001 (PCA# 010174) */ /* Motherboard doesn't have Host bridge * subvendor/subdevice IDs, therefore checking * its on-board VGA controller */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82801DB_2) switch(dev->subsystem_device) { case 0x00b8: /* Compaq Evo D510 CMT */ case 0x00b9: /* Compaq Evo D510 SFF */ case 0x00ba: /* Compaq Evo D510 USDT */ /* Motherboard doesn't have Host bridge * subvendor/subdevice IDs and on-board VGA * controller is disabled if an AGP card is * inserted, therefore checking USB UHCI * Controller #1 */ asus_hides_smbus = 1; } else if (dev->device == PCI_DEVICE_ID_INTEL_82815_CGC) switch (dev->subsystem_device) { case 0x001A: /* Compaq Deskpro EN SSF P667 815E */ /* Motherboard doesn't have host bridge * subvendor/subdevice IDs, therefore checking * its on-board VGA controller */ asus_hides_smbus = 1; } } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845_HB, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_HB, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82850_HB, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_7205_0, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7501_MCH, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855PM_HB, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82855GM_HB, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82915GM_HB, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG3, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_2, asus_hides_smbus_hostbridge); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82815_CGC, asus_hides_smbus_hostbridge); static void asus_hides_smbus_lpc(struct pci_dev *dev) { u16 val; if (likely(!asus_hides_smbus)) return; pci_read_config_word(dev, 0xF2, &val); if (val & 0x8) { pci_write_config_word(dev, 0xF2, val & (~0x8)); pci_read_config_word(dev, 0xF2, &val); if (val & 0x8) dev_info(&dev->dev, "i801 SMBus device continues to play 'hide and seek'! 0x%x\n", val); else dev_info(&dev->dev, "Enabled i801 SMBus device\n"); } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_0, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_12, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_12, asus_hides_smbus_lpc); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0, asus_hides_smbus_lpc); /* It appears we just have one such device. If not, we have a warning */ static void __iomem *asus_rcba_base; static void asus_hides_smbus_lpc_ich6_suspend(struct pci_dev *dev) { u32 rcba; if (likely(!asus_hides_smbus)) return; WARN_ON(asus_rcba_base); pci_read_config_dword(dev, 0xF0, &rcba); /* use bits 31:14, 16 kB aligned */ asus_rcba_base = ioremap_nocache(rcba & 0xFFFFC000, 0x4000); if (asus_rcba_base == NULL) return; } static void asus_hides_smbus_lpc_ich6_resume_early(struct pci_dev *dev) { u32 val; if (likely(!asus_hides_smbus || !asus_rcba_base)) return; /* read the Function Disable register, dword mode only */ val = readl(asus_rcba_base + 0x3418); writel(val & 0xFFFFFFF7, asus_rcba_base + 0x3418); /* enable the SMBus device */ } static void asus_hides_smbus_lpc_ich6_resume(struct pci_dev *dev) { if (likely(!asus_hides_smbus || !asus_rcba_base)) return; iounmap(asus_rcba_base); asus_rcba_base = NULL; dev_info(&dev->dev, "Enabled ICH6/i801 SMBus device\n"); } static void asus_hides_smbus_lpc_ich6(struct pci_dev *dev) { asus_hides_smbus_lpc_ich6_suspend(dev); asus_hides_smbus_lpc_ich6_resume_early(dev); asus_hides_smbus_lpc_ich6_resume(dev); } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6); DECLARE_PCI_FIXUP_SUSPEND(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_suspend); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_resume); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_1, asus_hides_smbus_lpc_ich6_resume_early); /* * SiS 96x south bridge: BIOS typically hides SMBus device... */ static void quirk_sis_96x_smbus(struct pci_dev *dev) { u8 val = 0; pci_read_config_byte(dev, 0x77, &val); if (val & 0x10) { dev_info(&dev->dev, "Enabling SiS 96x SMBus\n"); pci_write_config_byte(dev, 0x77, val & ~0x10); } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_961, quirk_sis_96x_smbus); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_962, quirk_sis_96x_smbus); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus); /* * ... This is further complicated by the fact that some SiS96x south * bridges pretend to be 85C503/5513 instead. In that case see if we * spotted a compatible north bridge to make sure. * (pci_find_device doesn't work yet) * * We can also enable the sis96x bit in the discovery register.. */ #define SIS_DETECT_REGISTER 0x40 static void quirk_sis_503(struct pci_dev *dev) { u8 reg; u16 devid; pci_read_config_byte(dev, SIS_DETECT_REGISTER, ®); pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg | (1 << 6)); pci_read_config_word(dev, PCI_DEVICE_ID, &devid); if (((devid & 0xfff0) != 0x0960) && (devid != 0x0018)) { pci_write_config_byte(dev, SIS_DETECT_REGISTER, reg); return; } /* * Ok, it now shows up as a 96x.. run the 96x quirk by * hand in case it has already been processed. * (depends on link order, which is apparently not guaranteed) */ dev->device = devid; quirk_sis_96x_smbus(dev); } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503, quirk_sis_503); /* * On ASUS A8V and A8V Deluxe boards, the onboard AC97 audio controller * and MC97 modem controller are disabled when a second PCI soundcard is * present. This patch, tweaking the VT8237 ISA bridge, enables them. * -- bjd */ static void asus_hides_ac97_lpc(struct pci_dev *dev) { u8 val; int asus_hides_ac97 = 0; if (likely(dev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK)) { if (dev->device == PCI_DEVICE_ID_VIA_8237) asus_hides_ac97 = 1; } if (!asus_hides_ac97) return; pci_read_config_byte(dev, 0x50, &val); if (val & 0xc0) { pci_write_config_byte(dev, 0x50, val & (~0xc0)); pci_read_config_byte(dev, 0x50, &val); if (val & 0xc0) dev_info(&dev->dev, "Onboard AC97/MC97 devices continue to play 'hide and seek'! 0x%x\n", val); else dev_info(&dev->dev, "Enabled onboard AC97/MC97 devices\n"); } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, asus_hides_ac97_lpc); #if defined(CONFIG_ATA) || defined(CONFIG_ATA_MODULE) /* * If we are using libata we can drive this chip properly but must * do this early on to make the additional device appear during * the PCI scanning. */ static void quirk_jmicron_ata(struct pci_dev *pdev) { u32 conf1, conf5, class; u8 hdr; /* Only poke fn 0 */ if (PCI_FUNC(pdev->devfn)) return; pci_read_config_dword(pdev, 0x40, &conf1); pci_read_config_dword(pdev, 0x80, &conf5); conf1 &= ~0x00CFF302; /* Clear bit 1, 8, 9, 12-19, 22, 23 */ conf5 &= ~(1 << 24); /* Clear bit 24 */ switch (pdev->device) { case PCI_DEVICE_ID_JMICRON_JMB360: /* SATA single port */ case PCI_DEVICE_ID_JMICRON_JMB362: /* SATA dual ports */ case PCI_DEVICE_ID_JMICRON_JMB364: /* SATA dual ports */ /* The controller should be in single function ahci mode */ conf1 |= 0x0002A100; /* Set 8, 13, 15, 17 */ break; case PCI_DEVICE_ID_JMICRON_JMB365: case PCI_DEVICE_ID_JMICRON_JMB366: /* Redirect IDE second PATA port to the right spot */ conf5 |= (1 << 24); /* Fall through */ case PCI_DEVICE_ID_JMICRON_JMB361: case PCI_DEVICE_ID_JMICRON_JMB363: case PCI_DEVICE_ID_JMICRON_JMB369: /* Enable dual function mode, AHCI on fn 0, IDE fn1 */ /* Set the class codes correctly and then direct IDE 0 */ conf1 |= 0x00C2A1B3; /* Set 0, 1, 4, 5, 7, 8, 13, 15, 17, 22, 23 */ break; case PCI_DEVICE_ID_JMICRON_JMB368: /* The controller should be in single function IDE mode */ conf1 |= 0x00C00000; /* Set 22, 23 */ break; } pci_write_config_dword(pdev, 0x40, conf1); pci_write_config_dword(pdev, 0x80, conf5); /* Update pdev accordingly */ pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr); pdev->hdr_type = hdr & 0x7f; pdev->multifunction = !!(hdr & 0x80); pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class); pdev->class = class >> 8; } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB360, quirk_jmicron_ata); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, quirk_jmicron_ata); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB362, quirk_jmicron_ata); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, quirk_jmicron_ata); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB364, quirk_jmicron_ata); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, quirk_jmicron_ata); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, quirk_jmicron_ata); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, quirk_jmicron_ata); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB369, quirk_jmicron_ata); #endif #ifdef CONFIG_X86_IO_APIC static void __init quirk_alder_ioapic(struct pci_dev *pdev) { int i; if ((pdev->class >> 8) != 0xff00) return; /* the first BAR is the location of the IO APIC...we must * not touch this (and it's already covered by the fixmap), so * forcibly insert it into the resource tree */ if (pci_resource_start(pdev, 0) && pci_resource_len(pdev, 0)) insert_resource(&iomem_resource, &pdev->resource[0]); /* The next five BARs all seem to be rubbish, so just clean * them out */ for (i=1; i < 6; i++) { memset(&pdev->resource[i], 0, sizeof(pdev->resource[i])); } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EESSC, quirk_alder_ioapic); #endif static void __devinit quirk_pcie_mch(struct pci_dev *pdev) { pci_msi_off(pdev); pdev->no_msi = 1; } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, quirk_pcie_mch); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7320_MCH, quirk_pcie_mch); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7525_MCH, quirk_pcie_mch); /* * It's possible for the MSI to get corrupted if shpc and acpi * are used together on certain PXH-based systems. */ static void __devinit quirk_pcie_pxh(struct pci_dev *dev) { pci_msi_off(dev); dev->no_msi = 1; dev_warn(&dev->dev, "PXH quirk detected; SHPC device MSI disabled\n"); } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_0, quirk_pcie_pxh); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHD_1, quirk_pcie_pxh); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_pcie_pxh); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_pcie_pxh); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_pcie_pxh); /* * Some Intel PCI Express chipsets have trouble with downstream * device power management. */ static void quirk_intel_pcie_pm(struct pci_dev * dev) { pci_pm_d3_delay = 120; dev->no_d1d2 = 1; } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2601, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2602, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2603, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2604, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2605, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2606, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2607, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2608, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x2609, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260a, quirk_intel_pcie_pm); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260b, quirk_intel_pcie_pm); #ifdef CONFIG_X86_IO_APIC /* * Boot interrupts on some chipsets cannot be turned off. For these chipsets, * remap the original interrupt in the linux kernel to the boot interrupt, so * that a PCI device's interrupt handler is installed on the boot interrupt * line instead. */ static void quirk_reroute_to_boot_interrupts_intel(struct pci_dev *dev) { if (noioapicquirk || noioapicreroute) return; dev->irq_reroute_variant = INTEL_IRQ_REROUTE_VARIANT; dev_info(&dev->dev, "rerouting interrupts for [%04x:%04x]\n", dev->vendor, dev->device); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_0, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80333_1, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_0, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXH_1, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PXHV, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_0, quirk_reroute_to_boot_interrupts_intel); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80332_1, quirk_reroute_to_boot_interrupts_intel); /* * On some chipsets we can disable the generation of legacy INTx boot * interrupts. */ /* * IO-APIC1 on 6300ESB generates boot interrupts, see intel order no * 300641-004US, section 5.7.3. */ #define INTEL_6300_IOAPIC_ABAR 0x40 #define INTEL_6300_DISABLE_BOOT_IRQ (1<<14) static void quirk_disable_intel_boot_interrupt(struct pci_dev *dev) { u16 pci_config_word; if (noioapicquirk) return; pci_read_config_word(dev, INTEL_6300_IOAPIC_ABAR, &pci_config_word); pci_config_word |= INTEL_6300_DISABLE_BOOT_IRQ; pci_write_config_word(dev, INTEL_6300_IOAPIC_ABAR, pci_config_word); dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n", dev->vendor, dev->device); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, quirk_disable_intel_boot_interrupt); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_10, quirk_disable_intel_boot_interrupt); /* * disable boot interrupts on HT-1000 */ #define BC_HT1000_FEATURE_REG 0x64 #define BC_HT1000_PIC_REGS_ENABLE (1<<0) #define BC_HT1000_MAP_IDX 0xC00 #define BC_HT1000_MAP_DATA 0xC01 static void quirk_disable_broadcom_boot_interrupt(struct pci_dev *dev) { u32 pci_config_dword; u8 irq; if (noioapicquirk) return; pci_read_config_dword(dev, BC_HT1000_FEATURE_REG, &pci_config_dword); pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword | BC_HT1000_PIC_REGS_ENABLE); for (irq = 0x10; irq < 0x10 + 32; irq++) { outb(irq, BC_HT1000_MAP_IDX); outb(0x00, BC_HT1000_MAP_DATA); } pci_write_config_dword(dev, BC_HT1000_FEATURE_REG, pci_config_dword); dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n", dev->vendor, dev->device); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000SB, quirk_disable_broadcom_boot_interrupt); /* * disable boot interrupts on AMD and ATI chipsets */ /* * NOIOAMODE needs to be disabled to disable "boot interrupts". For AMD 8131 * rev. A0 and B0, NOIOAMODE needs to be disabled anyway to fix IO-APIC mode * (due to an erratum). */ #define AMD_813X_MISC 0x40 #define AMD_813X_NOIOAMODE (1<<0) #define AMD_813X_REV_B1 0x12 #define AMD_813X_REV_B2 0x13 static void quirk_disable_amd_813x_boot_interrupt(struct pci_dev *dev) { u32 pci_config_dword; if (noioapicquirk) return; if ((dev->revision == AMD_813X_REV_B1) || (dev->revision == AMD_813X_REV_B2)) return; pci_read_config_dword(dev, AMD_813X_MISC, &pci_config_dword); pci_config_dword &= ~AMD_813X_NOIOAMODE; pci_write_config_dword(dev, AMD_813X_MISC, pci_config_dword); dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n", dev->vendor, dev->device); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_amd_813x_boot_interrupt); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, quirk_disable_amd_813x_boot_interrupt); #define AMD_8111_PCI_IRQ_ROUTING 0x56 static void quirk_disable_amd_8111_boot_interrupt(struct pci_dev *dev) { u16 pci_config_word; if (noioapicquirk) return; pci_read_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, &pci_config_word); if (!pci_config_word) { dev_info(&dev->dev, "boot interrupts on device [%04x:%04x] " "already disabled\n", dev->vendor, dev->device); return; } pci_write_config_word(dev, AMD_8111_PCI_IRQ_ROUTING, 0); dev_info(&dev->dev, "disabled boot interrupts on device [%04x:%04x]\n", dev->vendor, dev->device); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt); DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS, quirk_disable_amd_8111_boot_interrupt); #endif /* CONFIG_X86_IO_APIC */ /* * Toshiba TC86C001 IDE controller reports the standard 8-byte BAR0 size * but the PIO transfers won't work if BAR0 falls at the odd 8 bytes. * Re-allocate the region if needed... */ static void __init quirk_tc86c001_ide(struct pci_dev *dev) { struct resource *r = &dev->resource[0]; if (r->start & 0x8) { r->start = 0; r->end = 0xf; } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_IDE, quirk_tc86c001_ide); static void __devinit quirk_netmos(struct pci_dev *dev) { unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4; unsigned int num_serial = dev->subsystem_device & 0xf; /* * These Netmos parts are multiport serial devices with optional * parallel ports. Even when parallel ports are present, they * are identified as class SERIAL, which means the serial driver * will claim them. To prevent this, mark them as class OTHER. * These combo devices should be claimed by parport_serial. * * The subdevice ID is of the form 0x00PS, where

is the number * of parallel ports and is the number of serial ports. */ switch (dev->device) { case PCI_DEVICE_ID_NETMOS_9835: /* Well, this rule doesn't hold for the following 9835 device */ if (dev->subsystem_vendor == PCI_VENDOR_ID_IBM && dev->subsystem_device == 0x0299) return; case PCI_DEVICE_ID_NETMOS_9735: case PCI_DEVICE_ID_NETMOS_9745: case PCI_DEVICE_ID_NETMOS_9845: case PCI_DEVICE_ID_NETMOS_9855: if ((dev->class >> 8) == PCI_CLASS_COMMUNICATION_SERIAL && num_parallel) { dev_info(&dev->dev, "Netmos %04x (%u parallel, " "%u serial); changing class SERIAL to OTHER " "(use parport_serial)\n", dev->device, num_parallel, num_serial); dev->class = (PCI_CLASS_COMMUNICATION_OTHER << 8) | (dev->class & 0xff); } } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NETMOS, PCI_ANY_ID, quirk_netmos); static void __devinit quirk_e100_interrupt(struct pci_dev *dev) { u16 command, pmcsr; u8 __iomem *csr; u8 cmd_hi; int pm; switch (dev->device) { /* PCI IDs taken from drivers/net/e100.c */ case 0x1029: case 0x1030 ... 0x1034: case 0x1038 ... 0x103E: case 0x1050 ... 0x1057: case 0x1059: case 0x1064 ... 0x106B: case 0x1091 ... 0x1095: case 0x1209: case 0x1229: case 0x2449: case 0x2459: case 0x245D: case 0x27DC: break; default: return; } /* * Some firmware hands off the e100 with interrupts enabled, * which can cause a flood of interrupts if packets are * received before the driver attaches to the device. So * disable all e100 interrupts here. The driver will * re-enable them when it's ready. */ pci_read_config_word(dev, PCI_COMMAND, &command); if (!(command & PCI_COMMAND_MEMORY) || !pci_resource_start(dev, 0)) return; /* * Check that the device is in the D0 power state. If it's not, * there is no point to look any further. */ pm = pci_find_capability(dev, PCI_CAP_ID_PM); if (pm) { pci_read_config_word(dev, pm + PCI_PM_CTRL, &pmcsr); if ((pmcsr & PCI_PM_CTRL_STATE_MASK) != PCI_D0) return; } /* Convert from PCI bus to resource space. */ csr = ioremap(pci_resource_start(dev, 0), 8); if (!csr) { dev_warn(&dev->dev, "Can't map e100 registers\n"); return; } cmd_hi = readb(csr + 3); if (cmd_hi == 0) { dev_warn(&dev->dev, "Firmware left e100 interrupts enabled; " "disabling\n"); writeb(1, csr + 3); } iounmap(csr); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, quirk_e100_interrupt); /* * The 82575 and 82598 may experience data corruption issues when transitioning * out of L0S. To prevent this we need to disable L0S on the pci-e link */ static void __devinit quirk_disable_aspm_l0s(struct pci_dev *dev) { dev_info(&dev->dev, "Disabling L0s\n"); pci_disable_link_state(dev, PCIE_LINK_STATE_L0S); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a7, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10a9, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10b6, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c6, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c7, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10c8, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10d6, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10db, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10dd, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10e1, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10ec, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f1, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x10f4, quirk_disable_aspm_l0s); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1508, quirk_disable_aspm_l0s); static void __devinit fixup_rev1_53c810(struct pci_dev* dev) { /* rev 1 ncr53c810 chips don't set the class at all which means * they don't get their resources remapped. Fix that here. */ if (dev->class == PCI_CLASS_NOT_DEFINED) { dev_info(&dev->dev, "NCR 53c810 rev 1 detected; setting PCI class\n"); dev->class = PCI_CLASS_STORAGE_SCSI; } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810); /* Enable 1k I/O space granularity on the Intel P64H2 */ static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev) { u16 en1k; u8 io_base_lo, io_limit_lo; unsigned long base, limit; struct resource *res = dev->resource + PCI_BRIDGE_RESOURCES; pci_read_config_word(dev, 0x40, &en1k); if (en1k & 0x200) { dev_info(&dev->dev, "Enable I/O Space to 1KB granularity\n"); pci_read_config_byte(dev, PCI_IO_BASE, &io_base_lo); pci_read_config_byte(dev, PCI_IO_LIMIT, &io_limit_lo); base = (io_base_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8; limit = (io_limit_lo & (PCI_IO_RANGE_MASK | 0x0c)) << 8; if (base <= limit) { res->start = base; res->end = limit + 0x3ff; } } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io); /* Fix the IOBL_ADR for 1k I/O space granularity on the Intel P64H2 * The IOBL_ADR gets re-written to 4k boundaries in pci_setup_bridge() * in drivers/pci/setup-bus.c */ static void __devinit quirk_p64h2_1k_io_fix_iobl(struct pci_dev *dev) { u16 en1k, iobl_adr, iobl_adr_1k; struct resource *res = dev->resource + PCI_BRIDGE_RESOURCES; pci_read_config_word(dev, 0x40, &en1k); if (en1k & 0x200) { pci_read_config_word(dev, PCI_IO_BASE, &iobl_adr); iobl_adr_1k = iobl_adr | (res->start >> 8) | (res->end & 0xfc00); if (iobl_adr != iobl_adr_1k) { dev_info(&dev->dev, "Fixing P64H2 IOBL_ADR from 0x%x to 0x%x for 1KB granularity\n", iobl_adr,iobl_adr_1k); pci_write_config_word(dev, PCI_IO_BASE, iobl_adr_1k); } } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x1460, quirk_p64h2_1k_io_fix_iobl); /* Under some circumstances, AER is not linked with extended capabilities. * Force it to be linked by setting the corresponding control bit in the * config space. */ static void quirk_nvidia_ck804_pcie_aer_ext_cap(struct pci_dev *dev) { uint8_t b; if (pci_read_config_byte(dev, 0xf41, &b) == 0) { if (!(b & 0x20)) { pci_write_config_byte(dev, 0xf41, b | 0x20); dev_info(&dev->dev, "Linking AER extended capability\n"); } } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, quirk_nvidia_ck804_pcie_aer_ext_cap); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, quirk_nvidia_ck804_pcie_aer_ext_cap); static void __devinit quirk_via_cx700_pci_parking_caching(struct pci_dev *dev) { /* * Disable PCI Bus Parking and PCI Master read caching on CX700 * which causes unspecified timing errors with a VT6212L on the PCI * bus leading to USB2.0 packet loss. * * This quirk is only enabled if a second (on the external PCI bus) * VT6212L is found -- the CX700 core itself also contains a USB * host controller with the same PCI ID as the VT6212L. */ /* Count VT6212L instances */ struct pci_dev *p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235_USB_2, NULL); uint8_t b; /* p should contain the first (internal) VT6212L -- see if we have an external one by searching again */ p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235_USB_2, p); if (!p) return; pci_dev_put(p); if (pci_read_config_byte(dev, 0x76, &b) == 0) { if (b & 0x40) { /* Turn off PCI Bus Parking */ pci_write_config_byte(dev, 0x76, b ^ 0x40); dev_info(&dev->dev, "Disabling VIA CX700 PCI parking\n"); } } if (pci_read_config_byte(dev, 0x72, &b) == 0) { if (b != 0) { /* Turn off PCI Master read caching */ pci_write_config_byte(dev, 0x72, 0x0); /* Set PCI Master Bus time-out to "1x16 PCLK" */ pci_write_config_byte(dev, 0x75, 0x1); /* Disable "Read FIFO Timer" */ pci_write_config_byte(dev, 0x77, 0x0); dev_info(&dev->dev, "Disabling VIA CX700 PCI caching\n"); } } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_caching); /* * For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the * VPD end tag will hang the device. This problem was initially * observed when a vpd entry was created in sysfs * ('/sys/bus/pci/devices//vpd'). A read to this sysfs entry * will dump 32k of data. Reading a full 32k will cause an access * beyond the VPD end tag causing the device to hang. Once the device * is hung, the bnx2 driver will not be able to reset the device. * We believe that it is legal to read beyond the end tag and * therefore the solution is to limit the read/write length. */ static void __devinit quirk_brcm_570x_limit_vpd(struct pci_dev *dev) { /* * Only disable the VPD capability for 5706, 5706S, 5708, * 5708S and 5709 rev. A */ if ((dev->device == PCI_DEVICE_ID_NX2_5706) || (dev->device == PCI_DEVICE_ID_NX2_5706S) || (dev->device == PCI_DEVICE_ID_NX2_5708) || (dev->device == PCI_DEVICE_ID_NX2_5708S) || ((dev->device == PCI_DEVICE_ID_NX2_5709) && (dev->revision & 0xf0) == 0x0)) { if (dev->vpd) dev->vpd->len = 0x80; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_NX2_5706, quirk_brcm_570x_limit_vpd); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_NX2_5706S, quirk_brcm_570x_limit_vpd); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_NX2_5708, quirk_brcm_570x_limit_vpd); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_NX2_5708S, quirk_brcm_570x_limit_vpd); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_NX2_5709, quirk_brcm_570x_limit_vpd); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_NX2_5709S, quirk_brcm_570x_limit_vpd); /* Originally in EDAC sources for i82875P: * Intel tells BIOS developers to hide device 6 which * configures the overflow device access containing * the DRBs - this is where we expose device 6. * http://www.x86-secret.com/articles/tweak/pat/patsecrets-2.htm */ static void __devinit quirk_unhide_mch_dev6(struct pci_dev *dev) { u8 reg; if (pci_read_config_byte(dev, 0xF4, ®) == 0 && !(reg & 0x02)) { dev_info(&dev->dev, "Enabling MCH 'Overflow' Device\n"); pci_write_config_byte(dev, 0xF4, reg | 0x02); } } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82865_HB, quirk_unhide_mch_dev6); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82875_HB, quirk_unhide_mch_dev6); #ifdef CONFIG_TILE /* * The Tilera TILEmpower platform needs to set the link speed * to 2.5GT(Giga-Transfers)/s (Gen 1). The default link speed * setting is 5GT/s (Gen 2). 0x98 is the Link Control2 PCIe * capability register of the PEX8624 PCIe switch. The switch * supports link speed auto negotiation, but falsely sets * the link speed to 5GT/s. */ static void __devinit quirk_tile_plx_gen1(struct pci_dev *dev) { if (tile_plx_gen1) { pci_write_config_dword(dev, 0x98, 0x1); mdelay(50); } } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_PLX, 0x8624, quirk_tile_plx_gen1); #endif /* CONFIG_TILE */ #ifdef CONFIG_PCI_MSI /* Some chipsets do not support MSI. We cannot easily rely on setting * PCI_BUS_FLAGS_NO_MSI in its bus flags because there are actually * some other busses controlled by the chipset even if Linux is not * aware of it. Instead of setting the flag on all busses in the * machine, simply disable MSI globally. */ static void __init quirk_disable_all_msi(struct pci_dev *dev) { pci_no_msi(); dev_warn(&dev->dev, "MSI quirk detected; MSI disabled\n"); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_GCNB_LE, quirk_disable_all_msi); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS400_200, quirk_disable_all_msi); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RS480, quirk_disable_all_msi); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3336, quirk_disable_all_msi); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3351, quirk_disable_all_msi); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_VT3364, quirk_disable_all_msi); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8380_0, quirk_disable_all_msi); /* Disable MSI on chipsets that are known to not support it */ static void __devinit quirk_disable_msi(struct pci_dev *dev) { if (dev->subordinate) { dev_warn(&dev->dev, "MSI quirk detected; " "subordinate MSI disabled\n"); dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_msi); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0xa238, quirk_disable_msi); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x5a3f, quirk_disable_msi); /* * The APC bridge device in AMD 780 family northbridges has some random * OEM subsystem ID in its vendor ID register (erratum 18), so instead * we use the possible vendor/device IDs of the host bridge for the * declared quirk, and search for the APC bridge by slot number. */ static void __devinit quirk_amd_780_apc_msi(struct pci_dev *host_bridge) { struct pci_dev *apc_bridge; apc_bridge = pci_get_slot(host_bridge->bus, PCI_DEVFN(1, 0)); if (apc_bridge) { if (apc_bridge->device == 0x9602) quirk_disable_msi(apc_bridge); pci_dev_put(apc_bridge); } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9600, quirk_amd_780_apc_msi); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x9601, quirk_amd_780_apc_msi); /* Go through the list of Hypertransport capabilities and * return 1 if a HT MSI capability is found and enabled */ static int __devinit msi_ht_cap_enabled(struct pci_dev *dev) { int pos, ttl = 48; pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); while (pos && ttl--) { u8 flags; if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, &flags) == 0) { dev_info(&dev->dev, "Found %s HT MSI Mapping\n", flags & HT_MSI_FLAGS_ENABLE ? "enabled" : "disabled"); return (flags & HT_MSI_FLAGS_ENABLE) != 0; } pos = pci_find_next_ht_capability(dev, pos, HT_CAPTYPE_MSI_MAPPING); } return 0; } /* Check the hypertransport MSI mapping to know whether MSI is enabled or not */ static void __devinit quirk_msi_ht_cap(struct pci_dev *dev) { if (dev->subordinate && !msi_ht_cap_enabled(dev)) { dev_warn(&dev->dev, "MSI quirk detected; " "subordinate MSI disabled\n"); dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE, quirk_msi_ht_cap); /* The nVidia CK804 chipset may have 2 HT MSI mappings. * MSI are supported if the MSI capability set in any of these mappings. */ static void __devinit quirk_nvidia_ck804_msi_ht_cap(struct pci_dev *dev) { struct pci_dev *pdev; if (!dev->subordinate) return; /* check HT MSI cap on this chipset and the root one. * a single one having MSI is enough to be sure that MSI are supported. */ pdev = pci_get_slot(dev->bus, 0); if (!pdev) return; if (!msi_ht_cap_enabled(dev) && !msi_ht_cap_enabled(pdev)) { dev_warn(&dev->dev, "MSI quirk detected; " "subordinate MSI disabled\n"); dev->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; } pci_dev_put(pdev); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_CK804_PCIE, quirk_nvidia_ck804_msi_ht_cap); /* Force enable MSI mapping capability on HT bridges */ static void __devinit ht_enable_msi_mapping(struct pci_dev *dev) { int pos, ttl = 48; pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); while (pos && ttl--) { u8 flags; if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, &flags) == 0) { dev_info(&dev->dev, "Enabling HT MSI Mapping\n"); pci_write_config_byte(dev, pos + HT_MSI_FLAGS, flags | HT_MSI_FLAGS_ENABLE); } pos = pci_find_next_ht_capability(dev, pos, HT_CAPTYPE_MSI_MAPPING); } } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000_PXB, ht_enable_msi_mapping); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8132_BRIDGE, ht_enable_msi_mapping); /* The P5N32-SLI motherboards from Asus have a problem with msi * for the MCP55 NIC. It is not yet determined whether the msi problem * also affects other devices. As for now, turn off msi for this device. */ static void __devinit nvenet_msi_disable(struct pci_dev *dev) { const char *board_name = dmi_get_system_info(DMI_BOARD_NAME); if (board_name && (strstr(board_name, "P5N32-SLI PREMIUM") || strstr(board_name, "P5N32-E SLI"))) { dev_info(&dev->dev, "Disabling msi for MCP55 NIC on P5N32-SLI\n"); dev->no_msi = 1; } } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_15, nvenet_msi_disable); /* * Some versions of the MCP55 bridge from nvidia have a legacy irq routing * config register. This register controls the routing of legacy interrupts * from devices that route through the MCP55. If this register is misprogramed * interrupts are only sent to the bsp, unlike conventional systems where the * irq is broadxast to all online cpus. Not having this register set * properly prevents kdump from booting up properly, so lets make sure that * we have it set correctly. * Note this is an undocumented register. */ static void __devinit nvbridge_check_legacy_irq_routing(struct pci_dev *dev) { u32 cfg; if (!pci_find_capability(dev, PCI_CAP_ID_HT)) return; pci_read_config_dword(dev, 0x74, &cfg); if (cfg & ((1 << 2) | (1 << 15))) { printk(KERN_INFO "Rewriting irq routing register on MCP55\n"); cfg &= ~((1 << 2) | (1 << 15)); pci_write_config_dword(dev, 0x74, cfg); } } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V0, nvbridge_check_legacy_irq_routing); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_MCP55_BRIDGE_V4, nvbridge_check_legacy_irq_routing); static int __devinit ht_check_msi_mapping(struct pci_dev *dev) { int pos, ttl = 48; int found = 0; /* check if there is HT MSI cap or enabled on this device */ pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); while (pos && ttl--) { u8 flags; if (found < 1) found = 1; if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, &flags) == 0) { if (flags & HT_MSI_FLAGS_ENABLE) { if (found < 2) { found = 2; break; } } } pos = pci_find_next_ht_capability(dev, pos, HT_CAPTYPE_MSI_MAPPING); } return found; } static int __devinit host_bridge_with_leaf(struct pci_dev *host_bridge) { struct pci_dev *dev; int pos; int i, dev_no; int found = 0; dev_no = host_bridge->devfn >> 3; for (i = dev_no + 1; i < 0x20; i++) { dev = pci_get_slot(host_bridge->bus, PCI_DEVFN(i, 0)); if (!dev) continue; /* found next host bridge ?*/ pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE); if (pos != 0) { pci_dev_put(dev); break; } if (ht_check_msi_mapping(dev)) { found = 1; pci_dev_put(dev); break; } pci_dev_put(dev); } return found; } #define PCI_HT_CAP_SLAVE_CTRL0 4 /* link control */ #define PCI_HT_CAP_SLAVE_CTRL1 8 /* link control to */ static int __devinit is_end_of_ht_chain(struct pci_dev *dev) { int pos, ctrl_off; int end = 0; u16 flags, ctrl; pos = pci_find_ht_capability(dev, HT_CAPTYPE_SLAVE); if (!pos) goto out; pci_read_config_word(dev, pos + PCI_CAP_FLAGS, &flags); ctrl_off = ((flags >> 10) & 1) ? PCI_HT_CAP_SLAVE_CTRL0 : PCI_HT_CAP_SLAVE_CTRL1; pci_read_config_word(dev, pos + ctrl_off, &ctrl); if (ctrl & (1 << 6)) end = 1; out: return end; } static void __devinit nv_ht_enable_msi_mapping(struct pci_dev *dev) { struct pci_dev *host_bridge; int pos; int i, dev_no; int found = 0; dev_no = dev->devfn >> 3; for (i = dev_no; i >= 0; i--) { host_bridge = pci_get_slot(dev->bus, PCI_DEVFN(i, 0)); if (!host_bridge) continue; pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE); if (pos != 0) { found = 1; break; } pci_dev_put(host_bridge); } if (!found) return; /* don't enable end_device/host_bridge with leaf directly here */ if (host_bridge == dev && is_end_of_ht_chain(host_bridge) && host_bridge_with_leaf(host_bridge)) goto out; /* root did that ! */ if (msi_ht_cap_enabled(host_bridge)) goto out; ht_enable_msi_mapping(dev); out: pci_dev_put(host_bridge); } static void __devinit ht_disable_msi_mapping(struct pci_dev *dev) { int pos, ttl = 48; pos = pci_find_ht_capability(dev, HT_CAPTYPE_MSI_MAPPING); while (pos && ttl--) { u8 flags; if (pci_read_config_byte(dev, pos + HT_MSI_FLAGS, &flags) == 0) { dev_info(&dev->dev, "Disabling HT MSI Mapping\n"); pci_write_config_byte(dev, pos + HT_MSI_FLAGS, flags & ~HT_MSI_FLAGS_ENABLE); } pos = pci_find_next_ht_capability(dev, pos, HT_CAPTYPE_MSI_MAPPING); } } static void __devinit __nv_msi_ht_cap_quirk(struct pci_dev *dev, int all) { struct pci_dev *host_bridge; int pos; int found; if (!pci_msi_enabled()) return; /* check if there is HT MSI cap or enabled on this device */ found = ht_check_msi_mapping(dev); /* no HT MSI CAP */ if (found == 0) return; /* * HT MSI mapping should be disabled on devices that are below * a non-Hypertransport host bridge. Locate the host bridge... */ host_bridge = pci_get_bus_and_slot(0, PCI_DEVFN(0, 0)); if (host_bridge == NULL) { dev_warn(&dev->dev, "nv_msi_ht_cap_quirk didn't locate host bridge\n"); return; } pos = pci_find_ht_capability(host_bridge, HT_CAPTYPE_SLAVE); if (pos != 0) { /* Host bridge is to HT */ if (found == 1) { /* it is not enabled, try to enable it */ if (all) ht_enable_msi_mapping(dev); else nv_ht_enable_msi_mapping(dev); } return; } /* HT MSI is not enabled */ if (found == 1) return; /* Host bridge is not to HT, disable HT MSI mapping on this device */ ht_disable_msi_mapping(dev); } static void __devinit nv_msi_ht_cap_quirk_all(struct pci_dev *dev) { return __nv_msi_ht_cap_quirk(dev, 1); } static void __devinit nv_msi_ht_cap_quirk_leaf(struct pci_dev *dev) { return __nv_msi_ht_cap_quirk(dev, 0); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_NVIDIA, PCI_ANY_ID, nv_msi_ht_cap_quirk_leaf); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_AL, PCI_ANY_ID, nv_msi_ht_cap_quirk_all); static void __devinit quirk_msi_intx_disable_bug(struct pci_dev *dev) { dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; } static void __devinit quirk_msi_intx_disable_ati_bug(struct pci_dev *dev) { struct pci_dev *p; /* SB700 MSI issue will be fixed at HW level from revision A21, * we need check PCI REVISION ID of SMBus controller to get SB700 * revision. */ p = pci_get_device(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS, NULL); if (!p) return; if ((p->revision < 0x3B) && (p->revision >= 0x30)) dev->dev_flags |= PCI_DEV_FLAGS_MSI_INTX_DISABLE_BUG; pci_dev_put(p); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5780, quirk_msi_intx_disable_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5780S, quirk_msi_intx_disable_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5714, quirk_msi_intx_disable_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5714S, quirk_msi_intx_disable_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5715, quirk_msi_intx_disable_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5715S, quirk_msi_intx_disable_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4390, quirk_msi_intx_disable_ati_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4391, quirk_msi_intx_disable_ati_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4392, quirk_msi_intx_disable_ati_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4393, quirk_msi_intx_disable_ati_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4394, quirk_msi_intx_disable_ati_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4373, quirk_msi_intx_disable_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4374, quirk_msi_intx_disable_bug); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4375, quirk_msi_intx_disable_bug); #endif /* CONFIG_PCI_MSI */ /* Allow manual resource allocation for PCI hotplug bridges * via pci=hpmemsize=nnM and pci=hpiosize=nnM parameters. For * some PCI-PCI hotplug bridges, like PLX 6254 (former HINT HB6), * kernel fails to allocate resources when hotplug device is * inserted and PCI bus is rescanned. */ static void __devinit quirk_hotplug_bridge(struct pci_dev *dev) { dev->is_hotplug_bridge = 1; } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_HINT, 0x0020, quirk_hotplug_bridge); /* * This is a quirk for the Ricoh MMC controller found as a part of * some mulifunction chips. * This is very similar and based on the ricoh_mmc driver written by * Philip Langdale. Thank you for these magic sequences. * * These chips implement the four main memory card controllers (SD, MMC, MS, xD) * and one or both of cardbus or firewire. * * It happens that they implement SD and MMC * support as separate controllers (and PCI functions). The linux SDHCI * driver supports MMC cards but the chip detects MMC cards in hardware * and directs them to the MMC controller - so the SDHCI driver never sees * them. * * To get around this, we must disable the useless MMC controller. * At that point, the SDHCI controller will start seeing them * It seems to be the case that the relevant PCI registers to deactivate the * MMC controller live on PCI function 0, which might be the cardbus controller * or the firewire controller, depending on the particular chip in question * * This has to be done early, because as soon as we disable the MMC controller * other pci functions shift up one level, e.g. function #2 becomes function * #1, and this will confuse the pci core. */ #ifdef CONFIG_MMC_RICOH_MMC static void ricoh_mmc_fixup_rl5c476(struct pci_dev *dev) { /* disable via cardbus interface */ u8 write_enable; u8 write_target; u8 disable; /* disable must be done via function #0 */ if (PCI_FUNC(dev->devfn)) return; pci_read_config_byte(dev, 0xB7, &disable); if (disable & 0x02) return; pci_read_config_byte(dev, 0x8E, &write_enable); pci_write_config_byte(dev, 0x8E, 0xAA); pci_read_config_byte(dev, 0x8D, &write_target); pci_write_config_byte(dev, 0x8D, 0xB7); pci_write_config_byte(dev, 0xB7, disable | 0x02); pci_write_config_byte(dev, 0x8E, write_enable); pci_write_config_byte(dev, 0x8D, write_target); dev_notice(&dev->dev, "proprietary Ricoh MMC controller disabled (via cardbus function)\n"); dev_notice(&dev->dev, "MMC cards are now supported by standard SDHCI controller\n"); } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476); static void ricoh_mmc_fixup_r5c832(struct pci_dev *dev) { /* disable via firewire interface */ u8 write_enable; u8 disable; /* disable must be done via function #0 */ if (PCI_FUNC(dev->devfn)) return; /* * RICOH 0xe823 SD/MMC card reader fails to recognize * certain types of SD/MMC cards. Lowering the SD base * clock frequency from 200Mhz to 50Mhz fixes this issue. * * 0x150 - SD2.0 mode enable for changing base clock * frequency to 50Mhz * 0xe1 - Base clock frequency * 0x32 - 50Mhz new clock frequency * 0xf9 - Key register for 0x150 * 0xfc - key register for 0xe1 */ if (dev->device == PCI_DEVICE_ID_RICOH_R5CE823) { pci_write_config_byte(dev, 0xf9, 0xfc); pci_write_config_byte(dev, 0x150, 0x10); pci_write_config_byte(dev, 0xf9, 0x00); pci_write_config_byte(dev, 0xfc, 0x01); pci_write_config_byte(dev, 0xe1, 0x32); pci_write_config_byte(dev, 0xfc, 0x00); dev_notice(&dev->dev, "MMC controller base frequency changed to 50Mhz.\n"); } pci_read_config_byte(dev, 0xCB, &disable); if (disable & 0x02) return; pci_read_config_byte(dev, 0xCA, &write_enable); pci_write_config_byte(dev, 0xCA, 0x57); pci_write_config_byte(dev, 0xCB, disable | 0x02); pci_write_config_byte(dev, 0xCA, write_enable); dev_notice(&dev->dev, "proprietary Ricoh MMC controller disabled (via firewire function)\n"); dev_notice(&dev->dev, "MMC cards are now supported by standard SDHCI controller\n"); } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832); DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5CE823, ricoh_mmc_fixup_r5c832); #endif /*CONFIG_MMC_RICOH_MMC*/ #ifdef CONFIG_DMAR_TABLE #define VTUNCERRMSK_REG 0x1ac #define VTD_MSK_SPEC_ERRORS (1 << 31) /* * This is a quirk for masking vt-d spec defined errors to platform error * handling logic. With out this, platforms using Intel 7500, 5500 chipsets * (and the derivative chipsets like X58 etc) seem to generate NMI/SMI (based * on the RAS config settings of the platform) when a vt-d fault happens. * The resulting SMI caused the system to hang. * * VT-d spec related errors are already handled by the VT-d OS code, so no * need to report the same error through other channels. */ static void vtd_mask_spec_errors(struct pci_dev *dev) { u32 word; pci_read_config_dword(dev, VTUNCERRMSK_REG, &word); pci_write_config_dword(dev, VTUNCERRMSK_REG, word | VTD_MSK_SPEC_ERRORS); } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x342e, vtd_mask_spec_errors); DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x3c28, vtd_mask_spec_errors); #endif static void __devinit fixup_ti816x_class(struct pci_dev* dev) { /* TI 816x devices do not have class code set when in PCIe boot mode */ if (dev->class == PCI_CLASS_NOT_DEFINED) { dev_info(&dev->dev, "Setting PCI class for 816x PCIe device\n"); dev->class = PCI_CLASS_MULTIMEDIA_VIDEO; } } DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_TI, 0xb800, fixup_ti816x_class); /* Some PCIe devices do not work reliably with the claimed maximum * payload size supported. */ static void __devinit fixup_mpss_256(struct pci_dev *dev) { dev->pcie_mpss = 1; /* 256 bytes */ } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SOLARFLARE, PCI_DEVICE_ID_SOLARFLARE_SFC4000A_0, fixup_mpss_256); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SOLARFLARE, PCI_DEVICE_ID_SOLARFLARE_SFC4000A_1, fixup_mpss_256); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SOLARFLARE, PCI_DEVICE_ID_SOLARFLARE_SFC4000B, fixup_mpss_256); /* Intel 5000 and 5100 Memory controllers have an errata with read completion * coalescing (which is enabled by default on some BIOSes) and MPS of 256B. * Since there is no way of knowing what the PCIE MPS on each fabric will be * until all of the devices are discovered and buses walked, read completion * coalescing must be disabled. Unfortunately, it cannot be re-enabled because * it is possible to hotplug a device with MPS of 256B. */ static void __devinit quirk_intel_mc_errata(struct pci_dev *dev) { int err; u16 rcc; if (pcie_bus_config == PCIE_BUS_TUNE_OFF) return; /* Intel errata specifies bits to change but does not say what they are. * Keeping them magical until such time as the registers and values can * be explained. */ err = pci_read_config_word(dev, 0x48, &rcc); if (err) { dev_err(&dev->dev, "Error attempting to read the read " "completion coalescing register.\n"); return; } if (!(rcc & (1 << 10))) return; rcc &= ~(1 << 10); err = pci_write_config_word(dev, 0x48, rcc); if (err) { dev_err(&dev->dev, "Error attempting to write the read " "completion coalescing register.\n"); return; } pr_info_once("Read completion coalescing disabled due to hardware " "errata relating to 256B MPS.\n"); } /* Intel 5000 series memory controllers and ports 2-7 */ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25c0, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d0, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d4, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25d8, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e2, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e3, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e4, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e5, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e6, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25e7, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f7, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f8, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25f9, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x25fa, quirk_intel_mc_errata); /* Intel 5100 series memory controllers and ports 2-7 */ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65c0, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e2, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e3, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e4, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e5, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e6, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65e7, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f7, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f8, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65f9, quirk_intel_mc_errata); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x65fa, quirk_intel_mc_errata); static void do_one_fixup_debug(void (*fn)(struct pci_dev *dev), struct pci_dev *dev) { ktime_t calltime, delta, rettime; unsigned long long duration; printk(KERN_DEBUG "calling %pF @ %i\n", fn, task_pid_nr(current)); calltime = ktime_get(); fn(dev); rettime = ktime_get(); delta = ktime_sub(rettime, calltime); duration = (unsigned long long) ktime_to_ns(delta) >> 10; printk(KERN_DEBUG "pci fixup %pF returned after %lld usecs\n", fn, duration); } /* * Some BIOS implementations leave the Intel GPU interrupts enabled, * even though no one is handling them (f.e. i915 driver is never loaded). * Additionally the interrupt destination is not set up properly * and the interrupt ends up -somewhere-. * * These spurious interrupts are "sticky" and the kernel disables * the (shared) interrupt line after 100.000+ generated interrupts. * * Fix it by disabling the still enabled interrupts. * This resolves crashes often seen on monitor unplug. */ #define I915_DEIER_REG 0x4400c static void __devinit disable_igfx_irq(struct pci_dev *dev) { void __iomem *regs = pci_iomap(dev, 0, 0); if (regs == NULL) { dev_warn(&dev->dev, "igfx quirk: Can't iomap PCI device\n"); return; } /* Check if any interrupt line is still enabled */ if (readl(regs + I915_DEIER_REG) != 0) { dev_warn(&dev->dev, "BIOS left Intel GPU interrupts enabled; " "disabling\n"); writel(0, regs + I915_DEIER_REG); } pci_iounmap(dev, regs); } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x0102, disable_igfx_irq); DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x010a, disable_igfx_irq); static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end) { for (; f < end; f++) if ((f->class == (u32) (dev->class >> f->class_shift) || f->class == (u32) PCI_ANY_ID) && (f->vendor == dev->vendor || f->vendor == (u16) PCI_ANY_ID) && (f->device == dev->device || f->device == (u16) PCI_ANY_ID)) { dev_dbg(&dev->dev, "calling %pF\n", f->hook); if (initcall_debug) do_one_fixup_debug(f->hook, dev); else f->hook(dev); } } extern struct pci_fixup __start_pci_fixups_early[]; extern struct pci_fixup __end_pci_fixups_early[]; extern struct pci_fixup __start_pci_fixups_header[]; extern struct pci_fixup __end_pci_fixups_header[]; extern struct pci_fixup __start_pci_fixups_final[]; extern struct pci_fixup __end_pci_fixups_final[]; extern struct pci_fixup __start_pci_fixups_enable[]; extern struct pci_fixup __end_pci_fixups_enable[]; extern struct pci_fixup __start_pci_fixups_resume[]; extern struct pci_fixup __end_pci_fixups_resume[]; extern struct pci_fixup __start_pci_fixups_resume_early[]; extern struct pci_fixup __end_pci_fixups_resume_early[]; extern struct pci_fixup __start_pci_fixups_suspend[]; extern struct pci_fixup __end_pci_fixups_suspend[]; void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev) { struct pci_fixup *start, *end; switch(pass) { case pci_fixup_early: start = __start_pci_fixups_early; end = __end_pci_fixups_early; break; case pci_fixup_header: start = __start_pci_fixups_header; end = __end_pci_fixups_header; break; case pci_fixup_final: start = __start_pci_fixups_final; end = __end_pci_fixups_final; break; case pci_fixup_enable: start = __start_pci_fixups_enable; end = __end_pci_fixups_enable; break; case pci_fixup_resume: start = __start_pci_fixups_resume; end = __end_pci_fixups_resume; break; case pci_fixup_resume_early: start = __start_pci_fixups_resume_early; end = __end_pci_fixups_resume_early; break; case pci_fixup_suspend: start = __start_pci_fixups_suspend; end = __end_pci_fixups_suspend; break; default: /* stupid compiler warning, you would think with an enum... */ return; } pci_do_fixups(dev, start, end); } EXPORT_SYMBOL(pci_fixup_device); static int __init pci_apply_final_quirks(void) { struct pci_dev *dev = NULL; u8 cls = 0; u8 tmp; if (pci_cache_line_size) printk(KERN_DEBUG "PCI: CLS %u bytes\n", pci_cache_line_size << 2); for_each_pci_dev(dev) { pci_fixup_device(pci_fixup_final, dev); /* * If arch hasn't set it explicitly yet, use the CLS * value shared by all PCI devices. If there's a * mismatch, fall back to the default value. */ if (!pci_cache_line_size) { pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &tmp); if (!cls) cls = tmp; if (!tmp || cls == tmp) continue; printk(KERN_DEBUG "PCI: CLS mismatch (%u != %u), " "using %u bytes\n", cls << 2, tmp << 2, pci_dfl_cache_line_size << 2); pci_cache_line_size = pci_dfl_cache_line_size; } } if (!pci_cache_line_size) { printk(KERN_DEBUG "PCI: CLS %u bytes, default %u\n", cls << 2, pci_dfl_cache_line_size << 2); pci_cache_line_size = cls ? cls : pci_dfl_cache_line_size; } return 0; } fs_initcall_sync(pci_apply_final_quirks); /* * Followings are device-specific reset methods which can be used to * reset a single function if other methods (e.g. FLR, PM D0->D3) are * not available. */ static int reset_intel_generic_dev(struct pci_dev *dev, int probe) { int pos; /* only implement PCI_CLASS_SERIAL_USB at present */ if (dev->class == PCI_CLASS_SERIAL_USB) { pos = pci_find_capability(dev, PCI_CAP_ID_VNDR); if (!pos) return -ENOTTY; if (probe) return 0; pci_write_config_byte(dev, pos + 0x4, 1); msleep(100); return 0; } else { return -ENOTTY; } } static int reset_intel_82599_sfp_virtfn(struct pci_dev *dev, int probe) { int pos; pos = pci_find_capability(dev, PCI_CAP_ID_EXP); if (!pos) return -ENOTTY; if (probe) return 0; pci_write_config_word(dev, pos + PCI_EXP_DEVCTL, PCI_EXP_DEVCTL_BCR_FLR); msleep(100); return 0; } #define PCI_DEVICE_ID_INTEL_82599_SFP_VF 0x10ed static const struct pci_dev_reset_methods pci_dev_reset_methods[] = { { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF, reset_intel_82599_sfp_virtfn }, { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, reset_intel_generic_dev }, { 0 } }; int pci_dev_specific_reset(struct pci_dev *dev, int probe) { const struct pci_dev_reset_methods *i; for (i = pci_dev_reset_methods; i->reset; i++) { if ((i->vendor == dev->vendor || i->vendor == (u16)PCI_ANY_ID) && (i->device == dev->device || i->device == (u16)PCI_ANY_ID)) return i->reset(dev, probe); } return -ENOTTY; }