/* * tms380tr.h: TI TMS380 Token Ring driver for Linux * * Authors: * - Christoph Goos * - Adam Fritzler */ #ifndef __LINUX_TMS380TR_H #define __LINUX_TMS380TR_H #ifdef __KERNEL__ #include /* module prototypes */ extern const struct net_device_ops tms380tr_netdev_ops; int tms380tr_open(struct net_device *dev); int tms380tr_close(struct net_device *dev); irqreturn_t tms380tr_interrupt(int irq, void *dev_id); int tmsdev_init(struct net_device *dev, struct device *pdev); void tmsdev_term(struct net_device *dev); void tms380tr_wait(unsigned long time); #define TMS380TR_MAX_ADAPTERS 7 #define SEND_TIMEOUT 10*HZ #define TR_RCF_LONGEST_FRAME_MASK 0x0070 #define TR_RCF_FRAME4K 0x0030 /*------------------------------------------------------------------*/ /* Bit order for adapter communication with DMA */ /* -------------------------------------------------------------- */ /* Bit 8 | 9| 10| 11|| 12| 13| 14| 15|| 0| 1| 2| 3|| 4| 5| 6| 7| */ /* -------------------------------------------------------------- */ /* The bytes in a word must be byte swapped. Also, if a double */ /* word is used for storage, then the words, as well as the bytes, */ /* must be swapped. */ /* Bit order for adapter communication with DIO */ /* -------------------------------------------------------------- */ /* Bit 0 | 1| 2| 3|| 4| 5| 6| 7|| 8| 9| 10| 11|| 12| 13| 14| 15| */ /* -------------------------------------------------------------- */ /*------------------------------------------------------------------*/ /* Swap words of a long. */ #define SWAPW(x) (((x) << 16) | ((x) >> 16)) /* Get the low byte of a word. */ #define LOBYTE(w) ((unsigned char)(w)) /* Get the high byte of a word. */ #define HIBYTE(w) ((unsigned char)((unsigned short)(w) >> 8)) /* Get the low word of a long. */ #define LOWORD(l) ((unsigned short)(l)) /* Get the high word of a long. */ #define HIWORD(l) ((unsigned short)((unsigned long)(l) >> 16)) /* Token ring adapter I/O addresses for normal mode. */ /* * The SIF registers. Common to all adapters. */ /* Basic SIF (SRSX = 0) */ #define SIFDAT 0x00 /* SIF/DMA data. */ #define SIFINC 0x02 /* IO Word data with auto increment. */ #define SIFINH 0x03 /* IO Byte data with auto increment. */ #define SIFADR 0x04 /* SIF/DMA Address. */ #define SIFCMD 0x06 /* SIF Command. */ #define SIFSTS 0x06 /* SIF Status. */ /* "Extended" SIF (SRSX = 1) */ #define SIFACL 0x08 /* SIF Adapter Control Register. */ #define SIFADD 0x0a /* SIF/DMA Address. -- 0x0a */ #define SIFADX 0x0c /* 0x0c */ #define DMALEN 0x0e /* SIF DMA length. -- 0x0e */ /* * POS Registers. Only for ISA Adapters. */ #define POSREG 0x10 /* Adapter Program Option Select (POS) * Register: base IO address + 16 byte. */ #define POSREG_2 24L /* only for TR4/16+ adapter * base IO address + 24 byte. -- 0x18 */ /* SIFCMD command codes (high-low) */ #define CMD_INTERRUPT_ADAPTER 0x8000 /* Cause internal adapter interrupt */ #define CMD_ADAPTER_RESET 0x4000 /* Hardware reset of adapter */ #define CMD_SSB_CLEAR 0x2000 /* Acknowledge to adapter to * system interrupts. */ #define CMD_EXECUTE 0x1000 /* Execute SCB command */ #define CMD_SCB_REQUEST 0x0800 /* Request adapter to interrupt * system when SCB is available for * another command. */ #define CMD_RX_CONTINUE 0x0400 /* Continue receive after odd pointer * stop. (odd pointer receive method) */ #define CMD_RX_VALID 0x0200 /* Now actual RPL is valid. */ #define CMD_TX_VALID 0x0100 /* Now actual TPL is valid. (valid * bit receive/transmit method) */ #define CMD_SYSTEM_IRQ 0x0080 /* Adapter-to-attached-system * interrupt is reset. */ #define CMD_CLEAR_SYSTEM_IRQ 0x0080 /* Clear SYSTEM_INTERRUPT bit. * (write: 1=ignore, 0=reset) */ #define EXEC_SOFT_RESET 0xFF00 /* adapter soft reset. (restart * adapter after hardware reset) */ /* ACL commands (high-low) */ #define ACL_SWHLDA 0x0800 /* Software hold acknowledge. */ #define ACL_SWDDIR 0x0400 /* Data transfer direction. */ #define ACL_SWHRQ 0x0200 /* Pseudo DMA operation. */ #define ACL_PSDMAEN 0x0100 /* Enable pseudo system DMA. */ #define ACL_ARESET 0x0080 /* Adapter hardware reset command. * (held in reset condition as * long as bit is set) */ #define ACL_CPHALT 0x0040 /* Communication processor halt. * (can only be set while ACL_ARESET * bit is set; prevents adapter * processor from executing code while * downloading firmware) */ #define ACL_BOOT 0x0020 #define ACL_SINTEN 0x0008 /* System interrupt enable/disable * (1/0): can be written if ACL_ARESET * is zero. */ #define ACL_PEN 0x0004 #define ACL_NSELOUT0 0x0002 #define ACL_NSELOUT1 0x0001 /* NSELOUTx have a card-specific * meaning for setting ring speed. */ #define PS_DMA_MASK (ACL_SWHRQ | ACL_PSDMAEN) /* SIFSTS register return codes (high-low) */ #define STS_SYSTEM_IRQ 0x0080 /* Adapter-to-attached-system * interrupt is valid. */ #define STS_INITIALIZE 0x0040 /* INITIALIZE status. (ready to * initialize) */ #define STS_TEST 0x0020 /* TEST status. (BUD not completed) */ #define STS_ERROR 0x0010 /* ERROR status. (unrecoverable * HW error occurred) */ #define STS_MASK 0x00F0 /* Mask interesting status bits. */ #define STS_ERROR_MASK 0x000F /* Get Error Code by masking the * interrupt code bits. */ #define ADAPTER_INT_PTRS 0x0A00 /* Address offset of adapter internal * pointers 01:0a00 (high-low) have to * be read after init and before open. */ /* Interrupt Codes (only MAC IRQs) */ #define STS_IRQ_ADAPTER_CHECK 0x0000 /* unrecoverable hardware or * software error. */ #define STS_IRQ_RING_STATUS 0x0004 /* SSB is updated with ring status. */ #define STS_IRQ_LLC_STATUS 0x0005 /* Not used in MAC-only microcode */ #define STS_IRQ_SCB_CLEAR 0x0006 /* SCB clear, following an * SCB_REQUEST IRQ. */ #define STS_IRQ_TIMER 0x0007 /* Not normally used in MAC ucode */ #define STS_IRQ_COMMAND_STATUS 0x0008 /* SSB is updated with command * status. */ #define STS_IRQ_RECEIVE_STATUS 0x000A /* SSB is updated with receive * status. */ #define STS_IRQ_TRANSMIT_STATUS 0x000C /* SSB is updated with transmit * status */ #define STS_IRQ_RECEIVE_PENDING 0x000E /* Not used in MAC-only microcode */ #define STS_IRQ_MASK 0x000F /* = STS_ERROR_MASK. */ /* TRANSMIT_STATUS completion code: (SSB.Parm[0]) */ #define COMMAND_COMPLETE 0x0080 /* TRANSMIT command completed * (avoid this!) issue another transmit * to send additional frames. */ #define FRAME_COMPLETE 0x0040 /* Frame has been transmitted; * INTERRUPT_FRAME bit was set in the * CSTAT request; indication of possibly * more than one frame transmissions! * SSB.Parm[0-1]: 32 bit pointer to * TPL of last frame. */ #define LIST_ERROR 0x0020 /* Error in one of the TPLs that * compose the frame; TRANSMIT * terminated; Parm[1-2]: 32bit pointer * to TPL which starts the error * frame; error details in bits 8-13. * (14?) */ #define FRAME_SIZE_ERROR 0x8000 /* FRAME_SIZE does not equal the sum of * the valid DATA_COUNT fields; * FRAME_SIZE less than header plus * information field. (15 bytes + * routing field) Or if FRAME_SIZE * was specified as zero in one list. */ #define TX_THRESHOLD 0x4000 /* FRAME_SIZE greater than (BUFFER_SIZE * - 9) * TX_BUF_MAX. */ #define ODD_ADDRESS 0x2000 /* Odd forward pointer value is * read on a list without END_FRAME * indication. */ #define FRAME_ERROR 0x1000 /* START_FRAME bit (not) anticipated, * but (not) set. */ #define ACCESS_PRIORITY_ERROR 0x0800 /* Access priority requested has not * been allowed. */ #define UNENABLED_MAC_FRAME 0x0400 /* MAC frame has source class of zero * or MAC frame PCF ATTN field is * greater than one. */ #define ILLEGAL_FRAME_FORMAT 0x0200 /* Bit 0 or FC field was set to one. */ /* * Since we need to support some functions even if the adapter is in a * CLOSED state, we have a (pseudo-) command queue which holds commands * that are outstandig to be executed. * * Each time a command completes, an interrupt occurs and the next * command is executed. The command queue is actually a simple word with * a bit for each outstandig command. Therefore the commands will not be * executed in the order they have been queued. * * The following defines the command code bits and the command queue: */ #define OC_OPEN 0x0001 /* OPEN command */ #define OC_TRANSMIT 0x0002 /* TRANSMIT command */ #define OC_TRANSMIT_HALT 0x0004 /* TRANSMIT_HALT command */ #define OC_RECEIVE 0x0008 /* RECEIVE command */ #define OC_CLOSE 0x0010 /* CLOSE command */ #define OC_SET_GROUP_ADDR 0x0020 /* SET_GROUP_ADDR command */ #define OC_SET_FUNCT_ADDR 0x0040 /* SET_FUNCT_ADDR command */ #define OC_READ_ERROR_LOG 0x0080 /* READ_ERROR_LOG command */ #define OC_READ_ADAPTER 0x0100 /* READ_ADAPTER command */ #define OC_MODIFY_OPEN_PARMS 0x0400 /* MODIFY_OPEN_PARMS command */ #define OC_RESTORE_OPEN_PARMS 0x0800 /* RESTORE_OPEN_PARMS command */ #define OC_SET_FIRST_16_GROUP 0x1000 /* SET_FIRST_16_GROUP command */ #define OC_SET_BRIDGE_PARMS 0x2000 /* SET_BRIDGE_PARMS command */ #define OC_CONFIG_BRIDGE_PARMS 0x4000 /* CONFIG_BRIDGE_PARMS command */ #define OPEN 0x0300 /* C: open command. S: completion. */ #define TRANSMIT 0x0400 /* C: transmit command. S: completion * status. (reject: COMMAND_REJECT if * adapter not opened, TRANSMIT already * issued or address passed in the SCB * not word aligned) */ #define TRANSMIT_HALT 0x0500 /* C: interrupt TX TPL chain; if no * TRANSMIT command issued, the command * is ignored (completion with TRANSMIT * status (0x0400)!) */ #define RECEIVE 0x0600 /* C: receive command. S: completion * status. (reject: COMMAND_REJECT if * adapter not opened, RECEIVE already * issued or address passed in the SCB * not word aligned) */ #define CLOSE 0x0700 /* C: close adapter. S: completion. * (COMMAND_REJECT if adapter not open) */ #define SET_GROUP_ADDR 0x0800 /* C: alter adapter group address after * OPEN. S: completion. (COMMAND_REJECT * if adapter not open) */ #define SET_FUNCT_ADDR 0x0900 /* C: alter adapter functional address * after OPEN. S: completion. * (COMMAND_REJECT if adapter not open) */ #define READ_ERROR_LOG 0x0A00 /* C: read adapter error counters. * S: completion. (command ignored * if adapter not open!) */ #define READ_ADAPTER 0x0B00 /* C: read data from adapter memory. * (important: after init and before * open!) S: completion. (ADAPTER_CHECK * interrupt if undefined storage area * read) */ #define MODIFY_OPEN_PARMS 0x0D00 /* C: modify some adapter operational * parameters. (bit correspondend to * WRAP_INTERFACE is ignored) * S: completion. (reject: * COMMAND_REJECT) */ #define RESTORE_OPEN_PARMS 0x0E00 /* C: modify some adapter operational * parameters. (bit correspondend * to WRAP_INTERFACE is ignored) * S: completion. (reject: * COMMAND_REJECT) */ #define SET_FIRST_16_GROUP 0x0F00 /* C: alter the first two bytes in * adapter group address. * S: completion. (reject: * COMMAND_REJECT) */ #define SET_BRIDGE_PARMS 0x1000 /* C: values and conditions for the * adapter hardware to use when frames * are copied for forwarding. * S: completion. (reject: * COMMAND_REJECT) */ #define CONFIG_BRIDGE_PARMS 0x1100 /* C: .. * S: completion. (reject: * COMMAND_REJECT) */ #define SPEED_4 4 #define SPEED_16 16 /* Default transmission speed */ /* Initialization Parameter Block (IPB); word alignment necessary! */ #define BURST_SIZE 0x0018 /* Default burst size */ #define BURST_MODE 0x9F00 /* Burst mode enable */ #define DMA_RETRIES 0x0505 /* Magic DMA retry number... */ #define CYCLE_TIME 3 /* Default AT-bus cycle time: 500 ns * (later adapter version: fix cycle time!) */ #define LINE_SPEED_BIT 0x80 /* Macro definition for the wait function. */ #define ONE_SECOND_TICKS 1000000 #define HALF_SECOND (ONE_SECOND_TICKS / 2) #define ONE_SECOND (ONE_SECOND_TICKS) #define TWO_SECONDS (ONE_SECOND_TICKS * 2) #define THREE_SECONDS (ONE_SECOND_TICKS * 3) #define FOUR_SECONDS (ONE_SECOND_TICKS * 4) #define FIVE_SECONDS (ONE_SECOND_TICKS * 5) #define BUFFER_SIZE 2048 /* Buffers on Adapter */ #pragma pack(1) typedef struct { unsigned short Init_Options; /* Initialize with burst mode; * LLC disabled. (MAC only) */ /* Interrupt vectors the adapter places on attached system bus. */ u_int8_t CMD_Status_IV; /* Interrupt vector: command status. */ u_int8_t TX_IV; /* Interrupt vector: transmit. */ u_int8_t RX_IV; /* Interrupt vector: receive. */ u_int8_t Ring_Status_IV; /* Interrupt vector: ring status. */ u_int8_t SCB_Clear_IV; /* Interrupt vector: SCB clear. */ u_int8_t Adapter_CHK_IV; /* Interrupt vector: adapter check. */ u_int16_t RX_Burst_Size; /* Max. number of transfer cycles. */ u_int16_t TX_Burst_Size; /* During DMA burst; even value! */ u_int16_t DMA_Abort_Thrhld; /* Number of DMA retries. */ u_int32_t SCB_Addr; /* SCB address: even, word aligned, high-low */ u_int32_t SSB_Addr; /* SSB address: even, word aligned, high-low */ } IPB, *IPB_Ptr; #pragma pack() /* * OPEN Command Parameter List (OCPL) (can be reused, if the adapter has to * be reopened) */ #define BUFFER_SIZE 2048 /* Buffers on Adapter. */ #define TPL_SIZE 8+6*TX_FRAG_NUM /* Depending on fragments per TPL. */ #define RPL_SIZE 14 /* (with TI firmware v2.26 handling * up to nine fragments possible) */ #define TX_BUF_MIN 20 /* ??? (Stephan: calculation with */ #define TX_BUF_MAX 40 /* BUFFER_SIZE and MAX_FRAME_SIZE) ??? */ #define DISABLE_EARLY_TOKEN_RELEASE 0x1000 /* OPEN Options (high-low) */ #define WRAP_INTERFACE 0x0080 /* Inserting omitted for test * purposes; transmit data appears * as receive data. (useful for * testing; change: CLOSE necessary) */ #define DISABLE_HARD_ERROR 0x0040 /* On HARD_ERROR & TRANSMIT_BEACON * no RING.STATUS interrupt. */ #define DISABLE_SOFT_ERROR 0x0020 /* On SOFT_ERROR, no RING.STATUS * interrupt. */ #define PASS_ADAPTER_MAC_FRAMES 0x0010 /* Passing unsupported MAC frames * to system. */ #define PASS_ATTENTION_FRAMES 0x0008 /* All changed attention MAC frames are * passed to the system. */ #define PAD_ROUTING_FIELD 0x0004 /* Routing field is padded to 18 * bytes. */ #define FRAME_HOLD 0x0002 /*Adapter waits for entire frame before * initiating DMA transfer; otherwise: * DMA transfer initiation if internal * buffer filled. */ #define CONTENDER 0x0001 /* Adapter participates in the monitor * contention process. */ #define PASS_BEACON_MAC_FRAMES 0x8000 /* Adapter passes beacon MAC frames * to the system. */ #define EARLY_TOKEN_RELEASE 0x1000 /* Only valid in 16 Mbps operation; * 0 = ETR. (no effect in 4 Mbps * operation) */ #define COPY_ALL_MAC_FRAMES 0x0400 /* All MAC frames are copied to * the system. (after OPEN: duplicate * address test (DAT) MAC frame is * first received frame copied to the * system) */ #define COPY_ALL_NON_MAC_FRAMES 0x0200 /* All non MAC frames are copied to * the system. */ #define PASS_FIRST_BUF_ONLY 0x0100 /* Passes only first internal buffer * of each received frame; FrameSize * of RPLs must contain internal * BUFFER_SIZE bits for promiscous mode. */ #define ENABLE_FULL_DUPLEX_SELECTION 0x2000 /* Enable the use of full-duplex * settings with bits in byte 22 in * ocpl. (new feature in firmware * version 3.09) */ /* Full-duplex settings */ #define OPEN_FULL_DUPLEX_OFF 0x0000 #define OPEN_FULL_DUPLEX_ON 0x00c0 #define OPEN_FULL_DUPLEX_AUTO 0x0080 #define PROD_ID_SIZE 18 /* Length of product ID. */ #define TX_FRAG_NUM 3 /* Number of fragments used in one TPL. */ #define TX_MORE_FRAGMENTS 0x8000 /* Bit set in DataCount to indicate more * fragments following. */ /* XXX is there some better way to do this? */ #define ISA_MAX_ADDRESS 0x00ffffff #define PCI_MAX_ADDRESS 0xffffffff #pragma pack(1) typedef struct { u_int16_t OPENOptions; u_int8_t NodeAddr[6]; /* Adapter node address; use ROM * address */ u_int32_t GroupAddr; /* Multicast: high order * bytes = 0xC000 */ u_int32_t FunctAddr; /* High order bytes = 0xC000 */ __be16 RxListSize; /* RPL size: 0 (=26), 14, 20 or * 26 bytes read by the adapter. * (Depending on the number of * fragments/list) */ __be16 TxListSize; /* TPL size */ __be16 BufSize; /* Is automatically rounded up to the * nearest nK boundary. */ u_int16_t FullDuplex; u_int16_t Reserved; u_int8_t TXBufMin; /* Number of adapter buffers reserved * for transmission a minimum of 2 * buffers must be allocated. */ u_int8_t TXBufMax; /* Maximum number of adapter buffers * for transmit; a minimum of 2 buffers * must be available for receive. * Default: 6 */ u_int16_t ProdIDAddr[2];/* Pointer to product ID. */ } OPB, *OPB_Ptr; #pragma pack() /* * SCB: adapter commands enabled by the host system started by writing * CMD_INTERRUPT_ADAPTER | CMD_EXECUTE (|SCB_REQUEST) to the SIFCMD IO * register. (special case: | CMD_SYSTEM_IRQ for initialization) */ #pragma pack(1) typedef struct { u_int16_t CMD; /* Command code */ u_int16_t Parm[2]; /* Pointer to Command Parameter Block */ } SCB; /* System Command Block (32 bit physical address; big endian)*/ #pragma pack() /* * SSB: adapter command return status can be evaluated after COMMAND_STATUS * adapter to system interrupt after reading SSB, the availability of the SSB * has to be told the adapter by writing CMD_INTERRUPT_ADAPTER | CMD_SSB_CLEAR * in the SIFCMD IO register. */ #pragma pack(1) typedef struct { u_int16_t STS; /* Status code */ u_int16_t Parm[3]; /* Parameter or pointer to Status Parameter * Block. */ } SSB; /* System Status Block (big endian - physical address) */ #pragma pack() typedef struct { unsigned short BurnedInAddrPtr; /* Pointer to adapter burned in * address. (BIA) */ unsigned short SoftwareLevelPtr;/* Pointer to software level data. */ unsigned short AdapterAddrPtr; /* Pointer to adapter addresses. */ unsigned short AdapterParmsPtr; /* Pointer to adapter parameters. */ unsigned short MACBufferPtr; /* Pointer to MAC buffer. (internal) */ unsigned short LLCCountersPtr; /* Pointer to LLC counters. */ unsigned short SpeedFlagPtr; /* Pointer to data rate flag. * (4/16 Mbps) */ unsigned short AdapterRAMPtr; /* Pointer to adapter RAM found. (KB) */ } INTPTRS; /* Adapter internal pointers */ #pragma pack(1) typedef struct { u_int8_t Line_Error; /* Line error: code violation in * frame or in a token, or FCS error. */ u_int8_t Internal_Error; /* IBM specific. (Reserved_1) */ u_int8_t Burst_Error; u_int8_t ARI_FCI_Error; /* ARI/FCI bit zero in AMP or * SMP MAC frame. */ u_int8_t AbortDelimeters; /* IBM specific. (Reserved_2) */ u_int8_t Reserved_3; u_int8_t Lost_Frame_Error; /* Receive of end of transmitted * frame failed. */ u_int8_t Rx_Congest_Error; /* Adapter in repeat mode has not * enough buffer space to copy incoming * frame. */ u_int8_t Frame_Copied_Error; /* ARI bit not zero in frame * addressed to adapter. */ u_int8_t Frequency_Error; /* IBM specific. (Reserved_4) */ u_int8_t Token_Error; /* (active only in monitor station) */ u_int8_t Reserved_5; u_int8_t DMA_Bus_Error; /* DMA bus errors not exceeding the * abort thresholds. */ u_int8_t DMA_Parity_Error; /* DMA parity errors not exceeding * the abort thresholds. */ } ERRORTAB; /* Adapter error counters */ #pragma pack() /*--------------------- Send and Receive definitions -------------------*/ #pragma pack(1) typedef struct { __be16 DataCount; /* Value 0, even and odd values are * permitted; value is unaltered most * significant bit set: following * fragments last fragment: most * significant bit is not evaluated. * (???) */ __be32 DataAddr; /* Pointer to frame data fragment; * even or odd. */ } Fragment; #pragma pack() #define MAX_FRAG_NUMBERS 9 /* Maximal number of fragments possible to use * in one RPL/TPL. (depending on TI firmware * version) */ /* * AC (1), FC (1), Dst (6), Src (6), RIF (18), Data (4472) = 4504 * The packet size can be one of the follows: 548, 1502, 2084, 4504, 8176, * 11439, 17832. Refer to TMS380 Second Generation Token Ring User's Guide * Page 2-27. */ #define HEADER_SIZE (1 + 1 + 6 + 6) #define SRC_SIZE 18 #define MIN_DATA_SIZE 516 #define DEFAULT_DATA_SIZE 4472 #define MAX_DATA_SIZE 17800 #define DEFAULT_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + DEFAULT_DATA_SIZE) #define MIN_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + MIN_DATA_SIZE) #define MAX_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + MAX_DATA_SIZE) /* * Macros to deal with the frame status field. */ #define AC_NOT_RECOGNIZED 0x00 #define GROUP_BIT 0x80 #define GET_TRANSMIT_STATUS_HIGH_BYTE(Ts) ((unsigned char)((Ts) >> 8)) #define GET_FRAME_STATUS_HIGH_AC(Fs) ((unsigned char)(((Fs) & 0xC0) >> 6)) #define GET_FRAME_STATUS_LOW_AC(Fs) ((unsigned char)(((Fs) & 0x0C) >> 2)) #define DIRECTED_FRAME(Context) (!((Context)->MData[2] & GROUP_BIT)) /*--------------------- Send Functions ---------------------------------*/ /* define TX_CSTAT _REQUEST (R) and _COMPLETE (C) values (high-low) */ #define TX_VALID 0x0080 /* R: set via TRANSMIT.VALID interrupt. * C: always reset to zero! */ #define TX_FRAME_COMPLETE 0x0040 /* R: must be reset to zero. * C: set to one. */ #define TX_START_FRAME 0x0020 /* R: start of a frame: 1 * C: unchanged. */ #define TX_END_FRAME 0x0010 /* R: end of a frame: 1 * C: unchanged. */ #define TX_FRAME_IRQ 0x0008 /* R: request interrupt generation * after transmission. * C: unchanged. */ #define TX_ERROR 0x0004 /* R: reserved. * C: set to one if Error occurred. */ #define TX_INTERFRAME_WAIT 0x0004 #define TX_PASS_CRC 0x0002 /* R: set if CRC value is already * calculated. (valid only in * FRAME_START TPL) * C: unchanged. */ #define TX_PASS_SRC_ADDR 0x0001 /* R: adapter uses explicit frame * source address and does not overwrite * with the adapter node address. * (valid only in FRAME_START TPL) * * C: unchanged. */ #define TX_STRIP_FS 0xFF00 /* R: reserved. * C: if no Transmission Error, * field contains copy of FS byte after * stripping of frame. */ /* * Structure of Transmit Parameter Lists (TPLs) (only one frame every TPL, * but possibly multiple TPLs for one frame) the length of the TPLs has to be * initialized in the OPL. (OPEN parameter list) */ #define TPL_NUM 3 /* Number of Transmit Parameter Lists. * !! MUST BE >= 3 !! */ #pragma pack(1) typedef struct s_TPL TPL; struct s_TPL { /* Transmit Parameter List (align on even word boundaries) */ __be32 NextTPLAddr; /* Pointer to next TPL in chain; if * pointer is odd: this is the last * TPL. Pointing to itself can cause * problems! */ volatile u_int16_t Status; /* Initialized by the adapter: * CSTAT_REQUEST important: update least * significant bit first! Set by the * adapter: CSTAT_COMPLETE status. */ __be16 FrameSize; /* Number of bytes to be transmitted * as a frame including AC/FC, * Destination, Source, Routing field * not including CRC, FS, End Delimiter * (valid only if START_FRAME bit in * CSTAT nonzero) must not be zero in * any list; maximum value: (BUFFER_SIZE * - 8) * TX_BUF_MAX sum of DataCount * values in FragmentList must equal * Frame_Size value in START_FRAME TPL! * frame data fragment list. */ /* TPL/RPL size in OPEN parameter list depending on maximal * numbers of fragments used in one parameter list. */ Fragment FragList[TX_FRAG_NUM]; /* Maximum: nine frame fragments in one * TPL actual version of firmware: 9 * fragments possible. */ #pragma pack() /* Special proprietary data and precalculations */ TPL *NextTPLPtr; /* Pointer to next TPL in chain. */ unsigned char *MData; struct sk_buff *Skb; unsigned char TPLIndex; volatile unsigned char BusyFlag;/* Flag: TPL busy? */ dma_addr_t DMABuff; /* DMA IO bus address from dma_map */ }; /* ---------------------Receive Functions-------------------------------* * define RECEIVE_CSTAT_REQUEST (R) and RECEIVE_CSTAT_COMPLETE (C) values. * (high-low) */ #define RX_VALID 0x0080 /* R: set; tell adapter with * RECEIVE.VALID interrupt. * C: reset to zero. */ #define RX_FRAME_COMPLETE 0x0040 /* R: must be reset to zero, * C: set to one. */ #define RX_START_FRAME 0x0020 /* R: must be reset to zero. * C: set to one on the list. */ #define RX_END_FRAME 0x0010 /* R: must be reset to zero. * C: set to one on the list * that ends the frame. */ #define RX_FRAME_IRQ 0x0008 /* R: request interrupt generation * after receive. * C: unchanged. */ #define RX_INTERFRAME_WAIT 0x0004 /* R: after receiving a frame: * interrupt and wait for a * RECEIVE.CONTINUE. * C: unchanged. */ #define RX_PASS_CRC 0x0002 /* R: if set, the adapter includes * the CRC in data passed. (last four * bytes; valid only if FRAME_START is * set) * C: set, if CRC is included in * received data. */ #define RX_PASS_SRC_ADDR 0x0001 /* R: adapter uses explicit frame * source address and does not * overwrite with the adapter node * address. (valid only if FRAME_START * is set) * C: unchanged. */ #define RX_RECEIVE_FS 0xFC00 /* R: reserved; must be reset to zero. * C: on lists with START_FRAME, field * contains frame status field from * received frame; otherwise cleared. */ #define RX_ADDR_MATCH 0x0300 /* R: reserved; must be reset to zero. * C: address match code mask. */ #define RX_STATUS_MASK 0x00FF /* Mask for receive status bits. */ #define RX_INTERN_ADDR_MATCH 0x0100 /* C: internally address match. */ #define RX_EXTERN_ADDR_MATCH 0x0200 /* C: externally matched via * XMATCH/XFAIL interface. */ #define RX_INTEXT_ADDR_MATCH 0x0300 /* C: internally and externally * matched. */ #define RX_READY (RX_VALID | RX_FRAME_IRQ) /* Ready for receive. */ /* Constants for Command Status Interrupt. * COMMAND_REJECT status field bit functions (SSB.Parm[0]) */ #define ILLEGAL_COMMAND 0x0080 /* Set if an unknown command * is issued to the adapter */ #define ADDRESS_ERROR 0x0040 /* Set if any address field in * the SCB is odd. (not word aligned) */ #define ADAPTER_OPEN 0x0020 /* Command issued illegal with * open adapter. */ #define ADAPTER_CLOSE 0x0010 /* Command issued illegal with * closed adapter. */ #define SAME_COMMAND 0x0008 /* Command issued with same command * already executing. */ /* OPEN_COMPLETION values (SSB.Parm[0], MSB) */ #define NODE_ADDR_ERROR 0x0040 /* Wrong address or BIA read * zero address. */ #define LIST_SIZE_ERROR 0x0020 /* If List_Size value not in 0, * 14, 20, 26. */ #define BUF_SIZE_ERROR 0x0010 /* Not enough available memory for * two buffers. */ #define TX_BUF_COUNT_ERROR 0x0004 /* Remaining receive buffers less than * two. */ #define OPEN_ERROR 0x0002 /* Error during ring insertion; more * information in bits 8-15. */ /* Standard return codes */ #define GOOD_COMPLETION 0x0080 /* =OPEN_SUCCESSFULL */ #define INVALID_OPEN_OPTION 0x0001 /* OPEN options are not supported by * the adapter. */ /* OPEN phases; details of OPEN_ERROR (SSB.Parm[0], LSB) */ #define OPEN_PHASES_MASK 0xF000 /* Check only the bits 8-11. */ #define LOBE_MEDIA_TEST 0x1000 #define PHYSICAL_INSERTION 0x2000 #define ADDRESS_VERIFICATION 0x3000 #define PARTICIPATION_IN_RING_POLL 0x4000 #define REQUEST_INITIALISATION 0x5000 #define FULLDUPLEX_CHECK 0x6000 /* OPEN error codes; details of OPEN_ERROR (SSB.Parm[0], LSB) */ #define OPEN_ERROR_CODES_MASK 0x0F00 /* Check only the bits 12-15. */ #define OPEN_FUNCTION_FAILURE 0x0100 /* Unable to transmit to itself or * frames received before insertion. */ #define OPEN_SIGNAL_LOSS 0x0200 /* Signal loss condition detected at * receiver. */ #define OPEN_TIMEOUT 0x0500 /* Insertion timer expired before * logical insertion. */ #define OPEN_RING_FAILURE 0x0600 /* Unable to receive own ring purge * MAC frames. */ #define OPEN_RING_BEACONING 0x0700 /* Beacon MAC frame received after * ring insertion. */ #define OPEN_DUPLICATE_NODEADDR 0x0800 /* Other station in ring found * with the same address. */ #define OPEN_REQUEST_INIT 0x0900 /* RPS present but does not respond. */ #define OPEN_REMOVE_RECEIVED 0x0A00 /* Adapter received a remove adapter * MAC frame. */ #define OPEN_FULLDUPLEX_SET 0x0D00 /* Got this with full duplex on when * trying to connect to a normal ring. */ /* SET_BRIDGE_PARMS return codes: */ #define BRIDGE_INVALID_MAX_LEN 0x4000 /* MAX_ROUTING_FIELD_LENGTH odd, * less than 6 or > 30. */ #define BRIDGE_INVALID_SRC_RING 0x2000 /* SOURCE_RING number zero, too large * or = TARGET_RING. */ #define BRIDGE_INVALID_TRG_RING 0x1000 /* TARGET_RING number zero, too large * or = SOURCE_RING. */ #define BRIDGE_INVALID_BRDGE_NO 0x0800 /* BRIDGE_NUMBER too large. */ #define BRIDGE_INVALID_OPTIONS 0x0400 /* Invalid bridge options. */ #define BRIDGE_DIAGS_FAILED 0x0200 /* Diagnostics of TMS380SRA failed. */ #define BRIDGE_NO_SRA 0x0100 /* The TMS380SRA does not exist in HW * configuration. */ /* * Bring Up Diagnostics error codes. */ #define BUD_INITIAL_ERROR 0x0 #define BUD_CHECKSUM_ERROR 0x1 #define BUD_ADAPTER_RAM_ERROR 0x2 #define BUD_INSTRUCTION_ERROR 0x3 #define BUD_CONTEXT_ERROR 0x4 #define BUD_PROTOCOL_ERROR 0x5 #define BUD_INTERFACE_ERROR 0x6 /* BUD constants */ #define BUD_MAX_RETRIES 3 #define BUD_MAX_LOOPCNT 6 #define BUD_TIMEOUT 3000 /* Initialization constants */ #define INIT_MAX_RETRIES 3 /* Maximum three retries. */ #define INIT_MAX_LOOPCNT 22 /* Maximum loop counts. */ /* RING STATUS field values (high/low) */ #define SIGNAL_LOSS 0x0080 /* Loss of signal on the ring * detected. */ #define HARD_ERROR 0x0040 /* Transmitting or receiving beacon * frames. */ #define SOFT_ERROR 0x0020 /* Report error MAC frame * transmitted. */ #define TRANSMIT_BEACON 0x0010 /* Transmitting beacon frames on the * ring. */ #define LOBE_WIRE_FAULT 0x0008 /* Open or short circuit in the * cable to concentrator; adapter * closed. */ #define AUTO_REMOVAL_ERROR 0x0004 /* Lobe wrap test failed, deinserted; * adapter closed. */ #define REMOVE_RECEIVED 0x0001 /* Received a remove ring station MAC * MAC frame request; adapter closed. */ #define COUNTER_OVERFLOW 0x8000 /* Overflow of one of the adapters * error counters; READ.ERROR.LOG. */ #define SINGLE_STATION 0x4000 /* Adapter is the only station on the * ring. */ #define RING_RECOVERY 0x2000 /* Claim token MAC frames on the ring; * reset after ring purge frame. */ #define ADAPTER_CLOSED (LOBE_WIRE_FAULT | AUTO_REMOVAL_ERROR |\ REMOVE_RECEIVED) /* Adapter_check_block.Status field bit assignments: */ #define DIO_PARITY 0x8000 /* Adapter detects bad parity * through direct I/O access. */ #define DMA_READ_ABORT 0x4000 /* Aborting DMA read operation * from system Parm[0]: 0=timeout, * 1=parity error, 2=bus error; * Parm[1]: 32 bit pointer to host * system address at failure. */ #define DMA_WRITE_ABORT 0x2000 /* Aborting DMA write operation * to system. (parameters analogous to * DMA_READ_ABORT) */ #define ILLEGAL_OP_CODE 0x1000 /* Illegal operation code in the * the adapters firmware Parm[0]-2: * communications processor registers * R13-R15. */ #define PARITY_ERRORS 0x0800 /* Adapter detects internal bus * parity error. */ #define RAM_DATA_ERROR 0x0080 /* Valid only during RAM testing; * RAM data error Parm[0-1]: 32 bit * pointer to RAM location. */ #define RAM_PARITY_ERROR 0x0040 /* Valid only during RAM testing; * RAM parity error Parm[0-1]: 32 bit * pointer to RAM location. */ #define RING_UNDERRUN 0x0020 /* Internal DMA underrun when * transmitting onto ring. */ #define INVALID_IRQ 0x0008 /* Unrecognized interrupt generated * internal to adapter Parm[0-2]: * adapter register R13-R15. */ #define INVALID_ERROR_IRQ 0x0004 /* Unrecognized error interrupt * generated Parm[0-2]: adapter register * R13-R15. */ #define INVALID_XOP 0x0002 /* Unrecognized XOP request in * communication processor Parm[0-2]: * adapter register R13-R15. */ #define CHECKADDR 0x05E0 /* Adapter check status information * address offset. */ #define ROM_PAGE_0 0x0000 /* Adapter ROM page 0. */ /* * RECEIVE.STATUS interrupt result SSB values: (high-low) * (RECEIVE_COMPLETE field bit definitions in SSB.Parm[0]) */ #define RX_COMPLETE 0x0080 /* SSB.Parm[0]; SSB.Parm[1]: 32 * bit pointer to last RPL. */ #define RX_SUSPENDED 0x0040 /* SSB.Parm[0]; SSB.Parm[1]: 32 * bit pointer to RPL with odd * forward pointer. */ /* Valid receive CSTAT: */ #define RX_FRAME_CONTROL_BITS (RX_VALID | RX_START_FRAME | RX_END_FRAME | \ RX_FRAME_COMPLETE) #define VALID_SINGLE_BUFFER_FRAME (RX_START_FRAME | RX_END_FRAME | \ RX_FRAME_COMPLETE) typedef enum SKB_STAT SKB_STAT; enum SKB_STAT { SKB_UNAVAILABLE, SKB_DMA_DIRECT, SKB_DATA_COPY }; /* Receive Parameter List (RPL) The length of the RPLs has to be initialized * in the OPL. (OPEN parameter list) */ #define RPL_NUM 3 #define RX_FRAG_NUM 1 /* Maximal number of used fragments in one RPL. * (up to firmware v2.24: 3, now: up to 9) */ #pragma pack(1) typedef struct s_RPL RPL; struct s_RPL { /* Receive Parameter List */ __be32 NextRPLAddr; /* Pointer to next RPL in chain * (normalized = physical 32 bit * address) if pointer is odd: this * is last RPL. Pointing to itself can * cause problems! */ volatile u_int16_t Status; /* Set by creation of Receive Parameter * List RECEIVE_CSTAT_COMPLETE set by * adapter in lists that start or end * a frame. */ volatile __be16 FrameSize; /* Number of bytes received as a * frame including AC/FC, Destination, * Source, Routing field not including * CRC, FS (Frame Status), End Delimiter * (valid only if START_FRAME bit in * CSTAT nonzero) must not be zero in * any list; maximum value: (BUFFER_SIZE * - 8) * TX_BUF_MAX sum of DataCount * values in FragmentList must equal * Frame_Size value in START_FRAME TPL! * frame data fragment list */ /* TPL/RPL size in OPEN parameter list depending on maximal numbers * of fragments used in one parameter list. */ Fragment FragList[RX_FRAG_NUM]; /* Maximum: nine frame fragments in * one TPL. Actual version of firmware: * 9 fragments possible. */ #pragma pack() /* Special proprietary data and precalculations. */ RPL *NextRPLPtr; /* Logical pointer to next RPL in chain. */ unsigned char *MData; struct sk_buff *Skb; SKB_STAT SkbStat; int RPLIndex; dma_addr_t DMABuff; /* DMA IO bus address from dma_map */ }; /* Information that need to be kept for each board. */ typedef struct net_local { #pragma pack(1) IPB ipb; /* Initialization Parameter Block. */ SCB scb; /* System Command Block: system to adapter * communication. */ SSB ssb; /* System Status Block: adapter to system * communication. */ OPB ocpl; /* Open Options Parameter Block. */ ERRORTAB errorlogtable; /* Adapter statistic error counters. * (read from adapter memory) */ unsigned char ProductID[PROD_ID_SIZE + 1]; /* Product ID */ #pragma pack() TPL Tpl[TPL_NUM]; TPL *TplFree; TPL *TplBusy; unsigned char LocalTxBuffers[TPL_NUM][DEFAULT_PACKET_SIZE]; RPL Rpl[RPL_NUM]; RPL *RplHead; RPL *RplTail; unsigned char LocalRxBuffers[RPL_NUM][DEFAULT_PACKET_SIZE]; struct device *pdev; int DataRate; unsigned char ScbInUse; unsigned short CMDqueue; unsigned long AdapterOpenFlag:1; unsigned long AdapterVirtOpenFlag:1; unsigned long OpenCommandIssued:1; unsigned long TransmitCommandActive:1; unsigned long TransmitHaltScheduled:1; unsigned long HaltInProgress:1; unsigned long LobeWireFaultLogged:1; unsigned long ReOpenInProgress:1; unsigned long Sleeping:1; unsigned long LastOpenStatus; unsigned short CurrentRingStatus; unsigned long MaxPacketSize; unsigned long StartTime; unsigned long LastSendTime; struct tr_statistics MacStat; /* MAC statistics structure */ unsigned long dmalimit; /* the max DMA address (ie, ISA) */ dma_addr_t dmabuffer; /* the DMA bus address corresponding to priv. Might be different from virt_to_bus() for architectures with IO MMU (Alpha) */ struct timer_list timer; wait_queue_head_t wait_for_tok_int; INTPTRS intptrs; /* Internal adapter pointer. Must be read * before OPEN command. */ unsigned short (*setnselout)(struct net_device *); unsigned short (*sifreadb)(struct net_device *, unsigned short); void (*sifwriteb)(struct net_device *, unsigned short, unsigned short); unsigned short (*sifreadw)(struct net_device *, unsigned short); void (*sifwritew)(struct net_device *, unsigned short, unsigned short); spinlock_t lock; /* SMP protection */ void *tmspriv; } NET_LOCAL; #endif /* __KERNEL__ */ #endif /* __LINUX_TMS380TR_H */