/******************************************************************************* Intel PRO/1000 Linux driver Copyright(c) 1999 - 2010 Intel Corporation. This program is free software; you can redistribute it and/or modify it under the terms and conditions of the GNU General Public License, version 2, as published by the Free Software Foundation. This program is distributed in the hope it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. The full GNU General Public License is included in this distribution in the file called "COPYING". Contact Information: Linux NICS e1000-devel Mailing List Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 *******************************************************************************/ /* * 80003ES2LAN Gigabit Ethernet Controller (Copper) * 80003ES2LAN Gigabit Ethernet Controller (Serdes) */ #include "e1000.h" #define E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL 0x00 #define E1000_KMRNCTRLSTA_OFFSET_INB_CTRL 0x02 #define E1000_KMRNCTRLSTA_OFFSET_HD_CTRL 0x10 #define E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE 0x1F #define E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS 0x0008 #define E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS 0x0800 #define E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING 0x0010 #define E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT 0x0004 #define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT 0x0000 #define E1000_KMRNCTRLSTA_OPMODE_E_IDLE 0x2000 #define E1000_KMRNCTRLSTA_OPMODE_MASK 0x000C #define E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO 0x0004 #define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */ #define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN 0x00010000 #define DEFAULT_TIPG_IPGT_1000_80003ES2LAN 0x8 #define DEFAULT_TIPG_IPGT_10_100_80003ES2LAN 0x9 /* GG82563 PHY Specific Status Register (Page 0, Register 16 */ #define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Reversal Disab. */ #define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060 #define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI */ #define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX */ #define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Auto crossover */ /* PHY Specific Control Register 2 (Page 0, Register 26) */ #define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 /* 1=Reverse Auto-Negotiation */ /* MAC Specific Control Register (Page 2, Register 21) */ /* Tx clock speed for Link Down and 1000BASE-T for the following speeds */ #define GG82563_MSCR_TX_CLK_MASK 0x0007 #define GG82563_MSCR_TX_CLK_10MBPS_2_5 0x0004 #define GG82563_MSCR_TX_CLK_100MBPS_25 0x0005 #define GG82563_MSCR_TX_CLK_1000MBPS_25 0x0007 #define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */ /* DSP Distance Register (Page 5, Register 26) */ #define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M 1 = 50-80M 2 = 80-110M 3 = 110-140M 4 = >140M */ /* Kumeran Mode Control Register (Page 193, Register 16) */ #define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800 /* Max number of times Kumeran read/write should be validated */ #define GG82563_MAX_KMRN_RETRY 0x5 /* Power Management Control Register (Page 193, Register 20) */ #define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001 /* 1=Enable SERDES Electrical Idle */ /* In-Band Control Register (Page 194, Register 18) */ #define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding */ /* * A table for the GG82563 cable length where the range is defined * with a lower bound at "index" and the upper bound at * "index + 5". */ static const u16 e1000_gg82563_cable_length_table[] = { 0, 60, 115, 150, 150, 60, 115, 150, 180, 180, 0xFF }; #define GG82563_CABLE_LENGTH_TABLE_SIZE \ ARRAY_SIZE(e1000_gg82563_cable_length_table) static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw); static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask); static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask); static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw); static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw); static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw); static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex); static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw); static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, u16 *data); static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, u16 data); static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw); /** * e1000_init_phy_params_80003es2lan - Init ESB2 PHY func ptrs. * @hw: pointer to the HW structure **/ static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw) { struct e1000_phy_info *phy = &hw->phy; s32 ret_val; if (hw->phy.media_type != e1000_media_type_copper) { phy->type = e1000_phy_none; return 0; } else { phy->ops.power_up = e1000_power_up_phy_copper; phy->ops.power_down = e1000_power_down_phy_copper_80003es2lan; } phy->addr = 1; phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; phy->reset_delay_us = 100; phy->type = e1000_phy_gg82563; /* This can only be done after all function pointers are setup. */ ret_val = e1000e_get_phy_id(hw); /* Verify phy id */ if (phy->id != GG82563_E_PHY_ID) return -E1000_ERR_PHY; return ret_val; } /** * e1000_init_nvm_params_80003es2lan - Init ESB2 NVM func ptrs. * @hw: pointer to the HW structure **/ static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw) { struct e1000_nvm_info *nvm = &hw->nvm; u32 eecd = er32(EECD); u16 size; nvm->opcode_bits = 8; nvm->delay_usec = 1; switch (nvm->override) { case e1000_nvm_override_spi_large: nvm->page_size = 32; nvm->address_bits = 16; break; case e1000_nvm_override_spi_small: nvm->page_size = 8; nvm->address_bits = 8; break; default: nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8; break; } nvm->type = e1000_nvm_eeprom_spi; size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> E1000_EECD_SIZE_EX_SHIFT); /* * Added to a constant, "size" becomes the left-shift value * for setting word_size. */ size += NVM_WORD_SIZE_BASE_SHIFT; /* EEPROM access above 16k is unsupported */ if (size > 14) size = 14; nvm->word_size = 1 << size; return 0; } /** * e1000_init_mac_params_80003es2lan - Init ESB2 MAC func ptrs. * @hw: pointer to the HW structure **/ static s32 e1000_init_mac_params_80003es2lan(struct e1000_adapter *adapter) { struct e1000_hw *hw = &adapter->hw; struct e1000_mac_info *mac = &hw->mac; struct e1000_mac_operations *func = &mac->ops; /* Set media type */ switch (adapter->pdev->device) { case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: hw->phy.media_type = e1000_media_type_internal_serdes; break; default: hw->phy.media_type = e1000_media_type_copper; break; } /* Set mta register count */ mac->mta_reg_count = 128; /* Set rar entry count */ mac->rar_entry_count = E1000_RAR_ENTRIES; /* FWSM register */ mac->has_fwsm = true; /* ARC supported; valid only if manageability features are enabled. */ mac->arc_subsystem_valid = (er32(FWSM) & E1000_FWSM_MODE_MASK) ? true : false; /* Adaptive IFS not supported */ mac->adaptive_ifs = false; /* check for link */ switch (hw->phy.media_type) { case e1000_media_type_copper: func->setup_physical_interface = e1000_setup_copper_link_80003es2lan; func->check_for_link = e1000e_check_for_copper_link; break; case e1000_media_type_fiber: func->setup_physical_interface = e1000e_setup_fiber_serdes_link; func->check_for_link = e1000e_check_for_fiber_link; break; case e1000_media_type_internal_serdes: func->setup_physical_interface = e1000e_setup_fiber_serdes_link; func->check_for_link = e1000e_check_for_serdes_link; break; default: return -E1000_ERR_CONFIG; break; } /* set lan id for port to determine which phy lock to use */ hw->mac.ops.set_lan_id(hw); return 0; } static s32 e1000_get_variants_80003es2lan(struct e1000_adapter *adapter) { struct e1000_hw *hw = &adapter->hw; s32 rc; rc = e1000_init_mac_params_80003es2lan(adapter); if (rc) return rc; rc = e1000_init_nvm_params_80003es2lan(hw); if (rc) return rc; rc = e1000_init_phy_params_80003es2lan(hw); if (rc) return rc; return 0; } /** * e1000_acquire_phy_80003es2lan - Acquire rights to access PHY * @hw: pointer to the HW structure * * A wrapper to acquire access rights to the correct PHY. **/ static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw) { u16 mask; mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM; return e1000_acquire_swfw_sync_80003es2lan(hw, mask); } /** * e1000_release_phy_80003es2lan - Release rights to access PHY * @hw: pointer to the HW structure * * A wrapper to release access rights to the correct PHY. **/ static void e1000_release_phy_80003es2lan(struct e1000_hw *hw) { u16 mask; mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM; e1000_release_swfw_sync_80003es2lan(hw, mask); } /** * e1000_acquire_mac_csr_80003es2lan - Acquire rights to access Kumeran register * @hw: pointer to the HW structure * * Acquire the semaphore to access the Kumeran interface. * **/ static s32 e1000_acquire_mac_csr_80003es2lan(struct e1000_hw *hw) { u16 mask; mask = E1000_SWFW_CSR_SM; return e1000_acquire_swfw_sync_80003es2lan(hw, mask); } /** * e1000_release_mac_csr_80003es2lan - Release rights to access Kumeran Register * @hw: pointer to the HW structure * * Release the semaphore used to access the Kumeran interface **/ static void e1000_release_mac_csr_80003es2lan(struct e1000_hw *hw) { u16 mask; mask = E1000_SWFW_CSR_SM; e1000_release_swfw_sync_80003es2lan(hw, mask); } /** * e1000_acquire_nvm_80003es2lan - Acquire rights to access NVM * @hw: pointer to the HW structure * * Acquire the semaphore to access the EEPROM. **/ static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw) { s32 ret_val; ret_val = e1000_acquire_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); if (ret_val) return ret_val; ret_val = e1000e_acquire_nvm(hw); if (ret_val) e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); return ret_val; } /** * e1000_release_nvm_80003es2lan - Relinquish rights to access NVM * @hw: pointer to the HW structure * * Release the semaphore used to access the EEPROM. **/ static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw) { e1000e_release_nvm(hw); e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); } /** * e1000_acquire_swfw_sync_80003es2lan - Acquire SW/FW semaphore * @hw: pointer to the HW structure * @mask: specifies which semaphore to acquire * * Acquire the SW/FW semaphore to access the PHY or NVM. The mask * will also specify which port we're acquiring the lock for. **/ static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask) { u32 swfw_sync; u32 swmask = mask; u32 fwmask = mask << 16; s32 i = 0; s32 timeout = 50; while (i < timeout) { if (e1000e_get_hw_semaphore(hw)) return -E1000_ERR_SWFW_SYNC; swfw_sync = er32(SW_FW_SYNC); if (!(swfw_sync & (fwmask | swmask))) break; /* * Firmware currently using resource (fwmask) * or other software thread using resource (swmask) */ e1000e_put_hw_semaphore(hw); mdelay(5); i++; } if (i == timeout) { e_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n"); return -E1000_ERR_SWFW_SYNC; } swfw_sync |= swmask; ew32(SW_FW_SYNC, swfw_sync); e1000e_put_hw_semaphore(hw); return 0; } /** * e1000_release_swfw_sync_80003es2lan - Release SW/FW semaphore * @hw: pointer to the HW structure * @mask: specifies which semaphore to acquire * * Release the SW/FW semaphore used to access the PHY or NVM. The mask * will also specify which port we're releasing the lock for. **/ static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask) { u32 swfw_sync; while (e1000e_get_hw_semaphore(hw) != 0); /* Empty */ swfw_sync = er32(SW_FW_SYNC); swfw_sync &= ~mask; ew32(SW_FW_SYNC, swfw_sync); e1000e_put_hw_semaphore(hw); } /** * e1000_read_phy_reg_gg82563_80003es2lan - Read GG82563 PHY register * @hw: pointer to the HW structure * @offset: offset of the register to read * @data: pointer to the data returned from the operation * * Read the GG82563 PHY register. **/ static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, u32 offset, u16 *data) { s32 ret_val; u32 page_select; u16 temp; ret_val = e1000_acquire_phy_80003es2lan(hw); if (ret_val) return ret_val; /* Select Configuration Page */ if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { page_select = GG82563_PHY_PAGE_SELECT; } else { /* * Use Alternative Page Select register to access * registers 30 and 31 */ page_select = GG82563_PHY_PAGE_SELECT_ALT; } temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT); ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp); if (ret_val) { e1000_release_phy_80003es2lan(hw); return ret_val; } if (hw->dev_spec.e80003es2lan.mdic_wa_enable == true) { /* * The "ready" bit in the MDIC register may be incorrectly set * before the device has completed the "Page Select" MDI * transaction. So we wait 200us after each MDI command... */ udelay(200); /* ...and verify the command was successful. */ ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp); if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) { ret_val = -E1000_ERR_PHY; e1000_release_phy_80003es2lan(hw); return ret_val; } udelay(200); ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, data); udelay(200); } else { ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, data); } e1000_release_phy_80003es2lan(hw); return ret_val; } /** * e1000_write_phy_reg_gg82563_80003es2lan - Write GG82563 PHY register * @hw: pointer to the HW structure * @offset: offset of the register to read * @data: value to write to the register * * Write to the GG82563 PHY register. **/ static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, u32 offset, u16 data) { s32 ret_val; u32 page_select; u16 temp; ret_val = e1000_acquire_phy_80003es2lan(hw); if (ret_val) return ret_val; /* Select Configuration Page */ if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { page_select = GG82563_PHY_PAGE_SELECT; } else { /* * Use Alternative Page Select register to access * registers 30 and 31 */ page_select = GG82563_PHY_PAGE_SELECT_ALT; } temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT); ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp); if (ret_val) { e1000_release_phy_80003es2lan(hw); return ret_val; } if (hw->dev_spec.e80003es2lan.mdic_wa_enable == true) { /* * The "ready" bit in the MDIC register may be incorrectly set * before the device has completed the "Page Select" MDI * transaction. So we wait 200us after each MDI command... */ udelay(200); /* ...and verify the command was successful. */ ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp); if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) { e1000_release_phy_80003es2lan(hw); return -E1000_ERR_PHY; } udelay(200); ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, data); udelay(200); } else { ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, data); } e1000_release_phy_80003es2lan(hw); return ret_val; } /** * e1000_write_nvm_80003es2lan - Write to ESB2 NVM * @hw: pointer to the HW structure * @offset: offset of the register to read * @words: number of words to write * @data: buffer of data to write to the NVM * * Write "words" of data to the ESB2 NVM. **/ static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) { return e1000e_write_nvm_spi(hw, offset, words, data); } /** * e1000_get_cfg_done_80003es2lan - Wait for configuration to complete * @hw: pointer to the HW structure * * Wait a specific amount of time for manageability processes to complete. * This is a function pointer entry point called by the phy module. **/ static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw) { s32 timeout = PHY_CFG_TIMEOUT; u32 mask = E1000_NVM_CFG_DONE_PORT_0; if (hw->bus.func == 1) mask = E1000_NVM_CFG_DONE_PORT_1; while (timeout) { if (er32(EEMNGCTL) & mask) break; msleep(1); timeout--; } if (!timeout) { e_dbg("MNG configuration cycle has not completed.\n"); return -E1000_ERR_RESET; } return 0; } /** * e1000_phy_force_speed_duplex_80003es2lan - Force PHY speed and duplex * @hw: pointer to the HW structure * * Force the speed and duplex settings onto the PHY. This is a * function pointer entry point called by the phy module. **/ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw) { s32 ret_val; u16 phy_data; bool link; /* * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI * forced whenever speed and duplex are forced. */ ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); if (ret_val) return ret_val; phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_AUTO; ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, phy_data); if (ret_val) return ret_val; e_dbg("GG82563 PSCR: %X\n", phy_data); ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data); if (ret_val) return ret_val; e1000e_phy_force_speed_duplex_setup(hw, &phy_data); /* Reset the phy to commit changes. */ phy_data |= MII_CR_RESET; ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data); if (ret_val) return ret_val; udelay(1); if (hw->phy.autoneg_wait_to_complete) { e_dbg("Waiting for forced speed/duplex link " "on GG82563 phy.\n"); ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT, 100000, &link); if (ret_val) return ret_val; if (!link) { /* * We didn't get link. * Reset the DSP and cross our fingers. */ ret_val = e1000e_phy_reset_dsp(hw); if (ret_val) return ret_val; } /* Try once more */ ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT, 100000, &link); if (ret_val) return ret_val; } ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data); if (ret_val) return ret_val; /* * Resetting the phy means we need to verify the TX_CLK corresponds * to the link speed. 10Mbps -> 2.5MHz, else 25MHz. */ phy_data &= ~GG82563_MSCR_TX_CLK_MASK; if (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED) phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5; else phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25; /* * In addition, we must re-enable CRS on Tx for both half and full * duplex. */ phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data); return ret_val; } /** * e1000_get_cable_length_80003es2lan - Set approximate cable length * @hw: pointer to the HW structure * * Find the approximate cable length as measured by the GG82563 PHY. * This is a function pointer entry point called by the phy module. **/ static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw) { struct e1000_phy_info *phy = &hw->phy; s32 ret_val = 0; u16 phy_data, index; ret_val = e1e_rphy(hw, GG82563_PHY_DSP_DISTANCE, &phy_data); if (ret_val) goto out; index = phy_data & GG82563_DSPD_CABLE_LENGTH; if (index >= GG82563_CABLE_LENGTH_TABLE_SIZE - 5) { ret_val = -E1000_ERR_PHY; goto out; } phy->min_cable_length = e1000_gg82563_cable_length_table[index]; phy->max_cable_length = e1000_gg82563_cable_length_table[index + 5]; phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2; out: return ret_val; } /** * e1000_get_link_up_info_80003es2lan - Report speed and duplex * @hw: pointer to the HW structure * @speed: pointer to speed buffer * @duplex: pointer to duplex buffer * * Retrieve the current speed and duplex configuration. **/ static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed, u16 *duplex) { s32 ret_val; if (hw->phy.media_type == e1000_media_type_copper) { ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex); hw->phy.ops.cfg_on_link_up(hw); } else { ret_val = e1000e_get_speed_and_duplex_fiber_serdes(hw, speed, duplex); } return ret_val; } /** * e1000_reset_hw_80003es2lan - Reset the ESB2 controller * @hw: pointer to the HW structure * * Perform a global reset to the ESB2 controller. **/ static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw) { u32 ctrl, icr; s32 ret_val; /* * Prevent the PCI-E bus from sticking if there is no TLP connection * on the last TLP read/write transaction when MAC is reset. */ ret_val = e1000e_disable_pcie_master(hw); if (ret_val) e_dbg("PCI-E Master disable polling has failed.\n"); e_dbg("Masking off all interrupts\n"); ew32(IMC, 0xffffffff); ew32(RCTL, 0); ew32(TCTL, E1000_TCTL_PSP); e1e_flush(); msleep(10); ctrl = er32(CTRL); ret_val = e1000_acquire_phy_80003es2lan(hw); e_dbg("Issuing a global reset to MAC\n"); ew32(CTRL, ctrl | E1000_CTRL_RST); e1000_release_phy_80003es2lan(hw); ret_val = e1000e_get_auto_rd_done(hw); if (ret_val) /* We don't want to continue accessing MAC registers. */ return ret_val; /* Clear any pending interrupt events. */ ew32(IMC, 0xffffffff); icr = er32(ICR); ret_val = e1000_check_alt_mac_addr_generic(hw); return ret_val; } /** * e1000_init_hw_80003es2lan - Initialize the ESB2 controller * @hw: pointer to the HW structure * * Initialize the hw bits, LED, VFTA, MTA, link and hw counters. **/ static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw) { struct e1000_mac_info *mac = &hw->mac; u32 reg_data; s32 ret_val; u16 i; e1000_initialize_hw_bits_80003es2lan(hw); /* Initialize identification LED */ ret_val = e1000e_id_led_init(hw); if (ret_val) e_dbg("Error initializing identification LED\n"); /* This is not fatal and we should not stop init due to this */ /* Disabling VLAN filtering */ e_dbg("Initializing the IEEE VLAN\n"); mac->ops.clear_vfta(hw); /* Setup the receive address. */ e1000e_init_rx_addrs(hw, mac->rar_entry_count); /* Zero out the Multicast HASH table */ e_dbg("Zeroing the MTA\n"); for (i = 0; i < mac->mta_reg_count; i++) E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); /* Setup link and flow control */ ret_val = e1000e_setup_link(hw); /* Set the transmit descriptor write-back policy */ reg_data = er32(TXDCTL(0)); reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC; ew32(TXDCTL(0), reg_data); /* ...for both queues. */ reg_data = er32(TXDCTL(1)); reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC; ew32(TXDCTL(1), reg_data); /* Enable retransmit on late collisions */ reg_data = er32(TCTL); reg_data |= E1000_TCTL_RTLC; ew32(TCTL, reg_data); /* Configure Gigabit Carry Extend Padding */ reg_data = er32(TCTL_EXT); reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; reg_data |= DEFAULT_TCTL_EXT_GCEX_80003ES2LAN; ew32(TCTL_EXT, reg_data); /* Configure Transmit Inter-Packet Gap */ reg_data = er32(TIPG); reg_data &= ~E1000_TIPG_IPGT_MASK; reg_data |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN; ew32(TIPG, reg_data); reg_data = E1000_READ_REG_ARRAY(hw, E1000_FFLT, 0x0001); reg_data &= ~0x00100000; E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data); /* default to true to enable the MDIC W/A */ hw->dev_spec.e80003es2lan.mdic_wa_enable = true; ret_val = e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET >> E1000_KMRNCTRLSTA_OFFSET_SHIFT, &i); if (!ret_val) { if ((i & E1000_KMRNCTRLSTA_OPMODE_MASK) == E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO) hw->dev_spec.e80003es2lan.mdic_wa_enable = false; } /* * Clear all of the statistics registers (clear on read). It is * important that we do this after we have tried to establish link * because the symbol error count will increment wildly if there * is no link. */ e1000_clear_hw_cntrs_80003es2lan(hw); return ret_val; } /** * e1000_initialize_hw_bits_80003es2lan - Init hw bits of ESB2 * @hw: pointer to the HW structure * * Initializes required hardware-dependent bits needed for normal operation. **/ static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw) { u32 reg; /* Transmit Descriptor Control 0 */ reg = er32(TXDCTL(0)); reg |= (1 << 22); ew32(TXDCTL(0), reg); /* Transmit Descriptor Control 1 */ reg = er32(TXDCTL(1)); reg |= (1 << 22); ew32(TXDCTL(1), reg); /* Transmit Arbitration Control 0 */ reg = er32(TARC(0)); reg &= ~(0xF << 27); /* 30:27 */ if (hw->phy.media_type != e1000_media_type_copper) reg &= ~(1 << 20); ew32(TARC(0), reg); /* Transmit Arbitration Control 1 */ reg = er32(TARC(1)); if (er32(TCTL) & E1000_TCTL_MULR) reg &= ~(1 << 28); else reg |= (1 << 28); ew32(TARC(1), reg); } /** * e1000_copper_link_setup_gg82563_80003es2lan - Configure GG82563 Link * @hw: pointer to the HW structure * * Setup some GG82563 PHY registers for obtaining link **/ static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw) { struct e1000_phy_info *phy = &hw->phy; s32 ret_val; u32 ctrl_ext; u16 data; ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &data); if (ret_val) return ret_val; data |= GG82563_MSCR_ASSERT_CRS_ON_TX; /* Use 25MHz for both link down and 1000Base-T for Tx clock. */ data |= GG82563_MSCR_TX_CLK_1000MBPS_25; ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, data); if (ret_val) return ret_val; /* * Options: * MDI/MDI-X = 0 (default) * 0 - Auto for all speeds * 1 - MDI mode * 2 - MDI-X mode * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) */ ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL, &data); if (ret_val) return ret_val; data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; switch (phy->mdix) { case 1: data |= GG82563_PSCR_CROSSOVER_MODE_MDI; break; case 2: data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; break; case 0: default: data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; break; } /* * Options: * disable_polarity_correction = 0 (default) * Automatic Correction for Reversed Cable Polarity * 0 - Disabled * 1 - Enabled */ data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; if (phy->disable_polarity_correction) data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE; ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, data); if (ret_val) return ret_val; /* SW Reset the PHY so all changes take effect */ ret_val = e1000e_commit_phy(hw); if (ret_val) { e_dbg("Error Resetting the PHY\n"); return ret_val; } /* Bypass Rx and Tx FIFO's */ ret_val = e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL, E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS | E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS); if (ret_val) return ret_val; ret_val = e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE, &data); if (ret_val) return ret_val; data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE; ret_val = e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE, data); if (ret_val) return ret_val; ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL_2, &data); if (ret_val) return ret_val; data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL_2, data); if (ret_val) return ret_val; ctrl_ext = er32(CTRL_EXT); ctrl_ext &= ~(E1000_CTRL_EXT_LINK_MODE_MASK); ew32(CTRL_EXT, ctrl_ext); ret_val = e1e_rphy(hw, GG82563_PHY_PWR_MGMT_CTRL, &data); if (ret_val) return ret_val; /* * Do not init these registers when the HW is in IAMT mode, since the * firmware will have already initialized them. We only initialize * them if the HW is not in IAMT mode. */ if (!e1000e_check_mng_mode(hw)) { /* Enable Electrical Idle on the PHY */ data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; ret_val = e1e_wphy(hw, GG82563_PHY_PWR_MGMT_CTRL, data); if (ret_val) return ret_val; ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &data); if (ret_val) return ret_val; data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, data); if (ret_val) return ret_val; } /* * Workaround: Disable padding in Kumeran interface in the MAC * and in the PHY to avoid CRC errors. */ ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data); if (ret_val) return ret_val; data |= GG82563_ICR_DIS_PADDING; ret_val = e1e_wphy(hw, GG82563_PHY_INBAND_CTRL, data); if (ret_val) return ret_val; return 0; } /** * e1000_setup_copper_link_80003es2lan - Setup Copper Link for ESB2 * @hw: pointer to the HW structure * * Essentially a wrapper for setting up all things "copper" related. * This is a function pointer entry point called by the mac module. **/ static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw) { u32 ctrl; s32 ret_val; u16 reg_data; ctrl = er32(CTRL); ctrl |= E1000_CTRL_SLU; ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); ew32(CTRL, ctrl); /* * Set the mac to wait the maximum time between each * iteration and increase the max iterations when * polling the phy; this fixes erroneous timeouts at 10Mbps. */ ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 4), 0xFFFF); if (ret_val) return ret_val; ret_val = e1000_read_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9), ®_data); if (ret_val) return ret_val; reg_data |= 0x3F; ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9), reg_data); if (ret_val) return ret_val; ret_val = e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET_INB_CTRL, ®_data); if (ret_val) return ret_val; reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING; ret_val = e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET_INB_CTRL, reg_data); if (ret_val) return ret_val; ret_val = e1000_copper_link_setup_gg82563_80003es2lan(hw); if (ret_val) return ret_val; ret_val = e1000e_setup_copper_link(hw); return 0; } /** * e1000_cfg_on_link_up_80003es2lan - es2 link configuration after link-up * @hw: pointer to the HW structure * @duplex: current duplex setting * * Configure the KMRN interface by applying last minute quirks for * 10/100 operation. **/ static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw) { s32 ret_val = 0; u16 speed; u16 duplex; if (hw->phy.media_type == e1000_media_type_copper) { ret_val = e1000e_get_speed_and_duplex_copper(hw, &speed, &duplex); if (ret_val) return ret_val; if (speed == SPEED_1000) ret_val = e1000_cfg_kmrn_1000_80003es2lan(hw); else ret_val = e1000_cfg_kmrn_10_100_80003es2lan(hw, duplex); } return ret_val; } /** * e1000_cfg_kmrn_10_100_80003es2lan - Apply "quirks" for 10/100 operation * @hw: pointer to the HW structure * @duplex: current duplex setting * * Configure the KMRN interface by applying last minute quirks for * 10/100 operation. **/ static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex) { s32 ret_val; u32 tipg; u32 i = 0; u16 reg_data, reg_data2; reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT; ret_val = e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET_HD_CTRL, reg_data); if (ret_val) return ret_val; /* Configure Transmit Inter-Packet Gap */ tipg = er32(TIPG); tipg &= ~E1000_TIPG_IPGT_MASK; tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN; ew32(TIPG, tipg); do { ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); if (ret_val) return ret_val; ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data2); if (ret_val) return ret_val; i++; } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY)); if (duplex == HALF_DUPLEX) reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; else reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); return 0; } /** * e1000_cfg_kmrn_1000_80003es2lan - Apply "quirks" for gigabit operation * @hw: pointer to the HW structure * * Configure the KMRN interface by applying last minute quirks for * gigabit operation. **/ static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw) { s32 ret_val; u16 reg_data, reg_data2; u32 tipg; u32 i = 0; reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT; ret_val = e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET_HD_CTRL, reg_data); if (ret_val) return ret_val; /* Configure Transmit Inter-Packet Gap */ tipg = er32(TIPG); tipg &= ~E1000_TIPG_IPGT_MASK; tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN; ew32(TIPG, tipg); do { ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); if (ret_val) return ret_val; ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data2); if (ret_val) return ret_val; i++; } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY)); reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); return ret_val; } /** * e1000_read_kmrn_reg_80003es2lan - Read kumeran register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Acquire semaphore, then read the PHY register at offset * using the kumeran interface. The information retrieved is stored in data. * Release the semaphore before exiting. **/ static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, u16 *data) { u32 kmrnctrlsta; s32 ret_val = 0; ret_val = e1000_acquire_mac_csr_80003es2lan(hw); if (ret_val) return ret_val; kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) & E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN; ew32(KMRNCTRLSTA, kmrnctrlsta); udelay(2); kmrnctrlsta = er32(KMRNCTRLSTA); *data = (u16)kmrnctrlsta; e1000_release_mac_csr_80003es2lan(hw); return ret_val; } /** * e1000_write_kmrn_reg_80003es2lan - Write kumeran register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Acquire semaphore, then write the data to PHY register * at the offset using the kumeran interface. Release semaphore * before exiting. **/ static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, u16 data) { u32 kmrnctrlsta; s32 ret_val = 0; ret_val = e1000_acquire_mac_csr_80003es2lan(hw); if (ret_val) return ret_val; kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) & E1000_KMRNCTRLSTA_OFFSET) | data; ew32(KMRNCTRLSTA, kmrnctrlsta); udelay(2); e1000_release_mac_csr_80003es2lan(hw); return ret_val; } /** * e1000_read_mac_addr_80003es2lan - Read device MAC address * @hw: pointer to the HW structure **/ static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw) { s32 ret_val = 0; /* * If there's an alternate MAC address place it in RAR0 * so that it will override the Si installed default perm * address. */ ret_val = e1000_check_alt_mac_addr_generic(hw); if (ret_val) goto out; ret_val = e1000_read_mac_addr_generic(hw); out: return ret_val; } /** * e1000_power_down_phy_copper_80003es2lan - Remove link during PHY power down * @hw: pointer to the HW structure * * In the case of a PHY power down to save power, or to turn off link during a * driver unload, or wake on lan is not enabled, remove the link. **/ static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw) { /* If the management interface is not enabled, then power down */ if (!(hw->mac.ops.check_mng_mode(hw) || hw->phy.ops.check_reset_block(hw))) e1000_power_down_phy_copper(hw); } /** * e1000_clear_hw_cntrs_80003es2lan - Clear device specific hardware counters * @hw: pointer to the HW structure * * Clears the hardware counters by reading the counter registers. **/ static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw) { e1000e_clear_hw_cntrs_base(hw); er32(PRC64); er32(PRC127); er32(PRC255); er32(PRC511); er32(PRC1023); er32(PRC1522); er32(PTC64); er32(PTC127); er32(PTC255); er32(PTC511); er32(PTC1023); er32(PTC1522); er32(ALGNERRC); er32(RXERRC); er32(TNCRS); er32(CEXTERR); er32(TSCTC); er32(TSCTFC); er32(MGTPRC); er32(MGTPDC); er32(MGTPTC); er32(IAC); er32(ICRXOC); er32(ICRXPTC); er32(ICRXATC); er32(ICTXPTC); er32(ICTXATC); er32(ICTXQEC); er32(ICTXQMTC); er32(ICRXDMTC); } static struct e1000_mac_operations es2_mac_ops = { .read_mac_addr = e1000_read_mac_addr_80003es2lan, .id_led_init = e1000e_id_led_init, .check_mng_mode = e1000e_check_mng_mode_generic, /* check_for_link dependent on media type */ .cleanup_led = e1000e_cleanup_led_generic, .clear_hw_cntrs = e1000_clear_hw_cntrs_80003es2lan, .get_bus_info = e1000e_get_bus_info_pcie, .set_lan_id = e1000_set_lan_id_multi_port_pcie, .get_link_up_info = e1000_get_link_up_info_80003es2lan, .led_on = e1000e_led_on_generic, .led_off = e1000e_led_off_generic, .update_mc_addr_list = e1000e_update_mc_addr_list_generic, .write_vfta = e1000_write_vfta_generic, .clear_vfta = e1000_clear_vfta_generic, .reset_hw = e1000_reset_hw_80003es2lan, .init_hw = e1000_init_hw_80003es2lan, .setup_link = e1000e_setup_link, /* setup_physical_interface dependent on media type */ .setup_led = e1000e_setup_led_generic, }; static struct e1000_phy_operations es2_phy_ops = { .acquire = e1000_acquire_phy_80003es2lan, .check_polarity = e1000_check_polarity_m88, .check_reset_block = e1000e_check_reset_block_generic, .commit = e1000e_phy_sw_reset, .force_speed_duplex = e1000_phy_force_speed_duplex_80003es2lan, .get_cfg_done = e1000_get_cfg_done_80003es2lan, .get_cable_length = e1000_get_cable_length_80003es2lan, .get_info = e1000e_get_phy_info_m88, .read_reg = e1000_read_phy_reg_gg82563_80003es2lan, .release = e1000_release_phy_80003es2lan, .reset = e1000e_phy_hw_reset_generic, .set_d0_lplu_state = NULL, .set_d3_lplu_state = e1000e_set_d3_lplu_state, .write_reg = e1000_write_phy_reg_gg82563_80003es2lan, .cfg_on_link_up = e1000_cfg_on_link_up_80003es2lan, }; static struct e1000_nvm_operations es2_nvm_ops = { .acquire = e1000_acquire_nvm_80003es2lan, .read = e1000e_read_nvm_eerd, .release = e1000_release_nvm_80003es2lan, .update = e1000e_update_nvm_checksum_generic, .valid_led_default = e1000e_valid_led_default, .validate = e1000e_validate_nvm_checksum_generic, .write = e1000_write_nvm_80003es2lan, }; struct e1000_info e1000_es2_info = { .mac = e1000_80003es2lan, .flags = FLAG_HAS_HW_VLAN_FILTER | FLAG_HAS_JUMBO_FRAMES | FLAG_HAS_WOL | FLAG_APME_IN_CTRL3 | FLAG_RX_CSUM_ENABLED | FLAG_HAS_CTRLEXT_ON_LOAD | FLAG_RX_NEEDS_RESTART /* errata */ | FLAG_TARC_SET_BIT_ZERO /* errata */ | FLAG_APME_CHECK_PORT_B | FLAG_DISABLE_FC_PAUSE_TIME /* errata */ | FLAG_TIPG_MEDIUM_FOR_80003ESLAN, .flags2 = FLAG2_DMA_BURST, .pba = 38, .max_hw_frame_size = DEFAULT_JUMBO, .get_variants = e1000_get_variants_80003es2lan, .mac_ops = &es2_mac_ops, .phy_ops = &es2_phy_ops, .nvm_ops = &es2_nvm_ops, };