/* Copyright 2008-2010 Broadcom Corporation * * Unless you and Broadcom execute a separate written software license * agreement governing use of this software, this software is licensed to you * under the terms of the GNU General Public License version 2, available * at http://www.gnu.org/licenses/old-licenses/gpl-2.0.html (the "GPL"). * * Notwithstanding the above, under no circumstances may you combine this * software in any way with any other Broadcom software provided under a * license other than the GPL, without Broadcom's express prior written * consent. * * Written by Yaniv Rosner * */ #ifndef BNX2X_LINK_H #define BNX2X_LINK_H /***********************************************************/ /* Defines */ /***********************************************************/ #define DEFAULT_PHY_DEV_ADDR 3 #define E2_DEFAULT_PHY_DEV_ADDR 5 #define BNX2X_FLOW_CTRL_AUTO PORT_FEATURE_FLOW_CONTROL_AUTO #define BNX2X_FLOW_CTRL_TX PORT_FEATURE_FLOW_CONTROL_TX #define BNX2X_FLOW_CTRL_RX PORT_FEATURE_FLOW_CONTROL_RX #define BNX2X_FLOW_CTRL_BOTH PORT_FEATURE_FLOW_CONTROL_BOTH #define BNX2X_FLOW_CTRL_NONE PORT_FEATURE_FLOW_CONTROL_NONE #define SPEED_AUTO_NEG 0 #define SPEED_12000 12000 #define SPEED_12500 12500 #define SPEED_13000 13000 #define SPEED_15000 15000 #define SPEED_16000 16000 #define SFP_EEPROM_VENDOR_NAME_ADDR 0x14 #define SFP_EEPROM_VENDOR_NAME_SIZE 16 #define SFP_EEPROM_VENDOR_OUI_ADDR 0x25 #define SFP_EEPROM_VENDOR_OUI_SIZE 3 #define SFP_EEPROM_PART_NO_ADDR 0x28 #define SFP_EEPROM_PART_NO_SIZE 16 #define PWR_FLT_ERR_MSG_LEN 250 #define XGXS_EXT_PHY_TYPE(ext_phy_config) \ ((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK) #define XGXS_EXT_PHY_ADDR(ext_phy_config) \ (((ext_phy_config) & PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> \ PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT) #define SERDES_EXT_PHY_TYPE(ext_phy_config) \ ((ext_phy_config) & PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK) /* Single Media Direct board is the plain 577xx board with CX4/RJ45 jacks */ #define SINGLE_MEDIA_DIRECT(params) (params->num_phys == 1) /* Single Media board contains single external phy */ #define SINGLE_MEDIA(params) (params->num_phys == 2) /* Dual Media board contains two external phy with different media */ #define DUAL_MEDIA(params) (params->num_phys == 3) #define FW_PARAM_MDIO_CTRL_OFFSET 16 #define FW_PARAM_SET(phy_addr, phy_type, mdio_access) \ (phy_addr | phy_type | mdio_access << FW_PARAM_MDIO_CTRL_OFFSET) /***********************************************************/ /* Structs */ /***********************************************************/ #define INT_PHY 0 #define EXT_PHY1 1 #define EXT_PHY2 2 #define MAX_PHYS 3 /* Same configuration is shared between the XGXS and the first external phy */ #define LINK_CONFIG_SIZE (MAX_PHYS - 1) #define LINK_CONFIG_IDX(_phy_idx) ((_phy_idx == INT_PHY) ? \ 0 : (_phy_idx - 1)) /***********************************************************/ /* bnx2x_phy struct */ /* Defines the required arguments and function per phy */ /***********************************************************/ struct link_vars; struct link_params; struct bnx2x_phy; typedef u8 (*config_init_t)(struct bnx2x_phy *phy, struct link_params *params, struct link_vars *vars); typedef u8 (*read_status_t)(struct bnx2x_phy *phy, struct link_params *params, struct link_vars *vars); typedef void (*link_reset_t)(struct bnx2x_phy *phy, struct link_params *params); typedef void (*config_loopback_t)(struct bnx2x_phy *phy, struct link_params *params); typedef u8 (*format_fw_ver_t)(u32 raw, u8 *str, u16 *len); typedef void (*hw_reset_t)(struct bnx2x_phy *phy, struct link_params *params); typedef void (*set_link_led_t)(struct bnx2x_phy *phy, struct link_params *params, u8 mode); typedef void (*phy_specific_func_t)(struct bnx2x_phy *phy, struct link_params *params, u32 action); struct bnx2x_phy { u32 type; /* Loaded during init */ u8 addr; u8 flags; /* Require HW lock */ #define FLAGS_HW_LOCK_REQUIRED (1<<0) /* No Over-Current detection */ #define FLAGS_NOC (1<<1) /* Fan failure detection required */ #define FLAGS_FAN_FAILURE_DET_REQ (1<<2) /* Initialize first the XGXS and only then the phy itself */ #define FLAGS_INIT_XGXS_FIRST (1<<3) #define FLAGS_REARM_LATCH_SIGNAL (1<<6) #define FLAGS_SFP_NOT_APPROVED (1<<7) u8 def_md_devad; u8 reserved; /* preemphasis values for the rx side */ u16 rx_preemphasis[4]; /* preemphasis values for the tx side */ u16 tx_preemphasis[4]; /* EMAC address for access MDIO */ u32 mdio_ctrl; u32 supported; u32 media_type; #define ETH_PHY_UNSPECIFIED 0x0 #define ETH_PHY_SFP_FIBER 0x1 #define ETH_PHY_XFP_FIBER 0x2 #define ETH_PHY_DA_TWINAX 0x3 #define ETH_PHY_BASE_T 0x4 #define ETH_PHY_NOT_PRESENT 0xff /* The address in which version is located*/ u32 ver_addr; u16 req_flow_ctrl; u16 req_line_speed; u32 speed_cap_mask; u16 req_duplex; u16 rsrv; /* Called per phy/port init, and it configures LASI, speed, autoneg, duplex, flow control negotiation, etc. */ config_init_t config_init; /* Called due to interrupt. It determines the link, speed */ read_status_t read_status; /* Called when driver is unloading. Should reset the phy */ link_reset_t link_reset; /* Set the loopback configuration for the phy */ config_loopback_t config_loopback; /* Format the given raw number into str up to len */ format_fw_ver_t format_fw_ver; /* Reset the phy (both ports) */ hw_reset_t hw_reset; /* Set link led mode (on/off/oper)*/ set_link_led_t set_link_led; /* PHY Specific tasks */ phy_specific_func_t phy_specific_func; #define DISABLE_TX 1 #define ENABLE_TX 2 }; /* Inputs parameters to the CLC */ struct link_params { u8 port; /* Default / User Configuration */ u8 loopback_mode; #define LOOPBACK_NONE 0 #define LOOPBACK_EMAC 1 #define LOOPBACK_BMAC 2 #define LOOPBACK_XGXS 3 #define LOOPBACK_EXT_PHY 4 #define LOOPBACK_EXT 5 /* Device parameters */ u8 mac_addr[6]; u16 req_duplex[LINK_CONFIG_SIZE]; u16 req_flow_ctrl[LINK_CONFIG_SIZE]; u16 req_line_speed[LINK_CONFIG_SIZE]; /* Also determine AutoNeg */ /* shmem parameters */ u32 shmem_base; u32 shmem2_base; u32 speed_cap_mask[LINK_CONFIG_SIZE]; u32 switch_cfg; #define SWITCH_CFG_1G PORT_FEATURE_CON_SWITCH_1G_SWITCH #define SWITCH_CFG_10G PORT_FEATURE_CON_SWITCH_10G_SWITCH #define SWITCH_CFG_AUTO_DETECT PORT_FEATURE_CON_SWITCH_AUTO_DETECT u32 lane_config; /* Phy register parameter */ u32 chip_id; u32 feature_config_flags; #define FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED (1<<0) #define FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY (1<<2) #define FEATURE_CONFIG_BC_SUPPORTS_DUAL_PHY_OPT_MDL_VRFY (1<<3) /* Will be populated during common init */ struct bnx2x_phy phy[MAX_PHYS]; /* Will be populated during common init */ u8 num_phys; u8 rsrv; u16 hw_led_mode; /* part of the hw_config read from the shmem */ u32 multi_phy_config; /* Device pointer passed to all callback functions */ struct bnx2x *bp; u16 req_fc_auto_adv; /* Should be set to TX / BOTH when req_flow_ctrl is set to AUTO */ }; /* Output parameters */ struct link_vars { u8 phy_flags; u8 mac_type; #define MAC_TYPE_NONE 0 #define MAC_TYPE_EMAC 1 #define MAC_TYPE_BMAC 2 u8 phy_link_up; /* internal phy link indication */ u8 link_up; u16 line_speed; u16 duplex; u16 flow_ctrl; u16 ieee_fc; /* The same definitions as the shmem parameter */ u32 link_status; }; /***********************************************************/ /* Functions */ /***********************************************************/ u8 bnx2x_phy_init(struct link_params *input, struct link_vars *output); /* Reset the link. Should be called when driver or interface goes down Before calling phy firmware upgrade, the reset_ext_phy should be set to 0 */ u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars, u8 reset_ext_phy); /* bnx2x_link_update should be called upon link interrupt */ u8 bnx2x_link_update(struct link_params *input, struct link_vars *output); /* use the following phy functions to read/write from external_phy In order to use it to read/write internal phy registers, use DEFAULT_PHY_DEV_ADDR as devad, and (_bank + (_addr & 0xf)) as the register */ u8 bnx2x_phy_read(struct link_params *params, u8 phy_addr, u8 devad, u16 reg, u16 *ret_val); u8 bnx2x_phy_write(struct link_params *params, u8 phy_addr, u8 devad, u16 reg, u16 val); /* Reads the link_status from the shmem, and update the link vars accordingly */ void bnx2x_link_status_update(struct link_params *input, struct link_vars *output); /* returns string representing the fw_version of the external phy */ u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, u8 *version, u16 len); /* Set/Unset the led Basically, the CLC takes care of the led for the link, but in case one needs to set/unset the led unnaturally, set the "mode" to LED_MODE_OPER to blink the led, and LED_MODE_OFF to set the led off.*/ u8 bnx2x_set_led(struct link_params *params, struct link_vars *vars, u8 mode, u32 speed); #define LED_MODE_OFF 0 #define LED_MODE_ON 1 #define LED_MODE_OPER 2 #define LED_MODE_FRONT_PANEL_OFF 3 /* bnx2x_handle_module_detect_int should be called upon module detection interrupt */ void bnx2x_handle_module_detect_int(struct link_params *params); /* Get the actual link status. In case it returns 0, link is up, otherwise link is down*/ u8 bnx2x_test_link(struct link_params *input, struct link_vars *vars, u8 is_serdes); /* One-time initialization for external phy after power up */ u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base_path[], u32 shmem2_base_path[], u32 chip_id); /* Reset the external PHY using GPIO */ void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port); /* Reset the external of SFX7101 */ void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, struct bnx2x_phy *phy); void bnx2x_hw_reset_phy(struct link_params *params); /* Checks if HW lock is required for this phy/board type */ u8 bnx2x_hw_lock_required(struct bnx2x *bp, u32 shmem_base, u32 shmem2_base); /* Check swap bit and adjust PHY order */ u32 bnx2x_phy_selection(struct link_params *params); /* Probe the phys on board, and populate them in "params" */ u8 bnx2x_phy_probe(struct link_params *params); /* Checks if fan failure detection is required on one of the phys on board */ u8 bnx2x_fan_failure_det_req(struct bnx2x *bp, u32 shmem_base, u32 shmem2_base, u8 port); #endif /* BNX2X_LINK_H */