From 4325f6caad98c075b39f0eaaac6693a0dd43f646 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Wed, 8 May 2013 13:09:08 +0200 Subject: wireless: move crypto constants to ieee80211.h mac80211 and the Intel drivers all define crypto constants, move them to ieee80211.h instead. Reviewed-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- include/linux/ieee80211.h | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'include/linux') diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h index 06b0ed0..d826e5a 100644 --- a/include/linux/ieee80211.h +++ b/include/linux/ieee80211.h @@ -1829,6 +1829,15 @@ enum ieee80211_key_len { WLAN_KEY_LEN_AES_CMAC = 16, }; +#define IEEE80211_WEP_IV_LEN 4 +#define IEEE80211_WEP_ICV_LEN 4 +#define IEEE80211_CCMP_HDR_LEN 8 +#define IEEE80211_CCMP_MIC_LEN 8 +#define IEEE80211_CCMP_PN_LEN 6 +#define IEEE80211_TKIP_IV_LEN 8 +#define IEEE80211_TKIP_ICV_LEN 4 +#define IEEE80211_CMAC_PN_LEN 6 + /* Public action codes */ enum ieee80211_pub_actioncode { WLAN_PUB_ACTION_EXT_CHANSW_ANN = 4, -- cgit v1.1 From 3e59cb0ddfd2c59991f38e89352ad8a3c71b2374 Mon Sep 17 00:00:00 2001 From: Yuchung Cheng Date: Fri, 17 May 2013 13:45:05 +0000 Subject: tcp: remove bad timeout logic in fast recovery tcp_timeout_skb() was intended to trigger fast recovery on timeout, unfortunately in reality it often causes spurious retransmission storms during fast recovery. The particular sign is a fast retransmit over the highest sacked sequence (SND.FACK). Currently the RTO timer re-arming (as in RFC6298) offers a nice cushion to avoid spurious timeout: when SND.UNA advances the sender re-arms RTO and extends the timeout by icsk_rto. The sender does not offset the time elapsed since the packet at SND.UNA was sent. But if the next (DUP)ACK arrives later than ~RTTVAR and triggers tcp_fastretrans_alert(), then tcp_timeout_skb() will mark any packet sent before the icsk_rto interval lost, including one that's above the highest sacked sequence. Most likely a large part of scorebard will be marked. If most packets are not lost then the subsequent DUPACKs with new SACK blocks will cause the sender to continue to retransmit packets beyond SND.FACK spuriously. Even if only one packet is lost the sender may falsely retransmit almost the entire window. The situation becomes common in the world of bufferbloat: the RTT continues to grow as the queue builds up but RTTVAR remains small and close to the minimum 200ms. If a data packet is lost and the DUPACK triggered by the next data packet is slightly delayed, then a spurious retransmission storm forms. As the original comment on tcp_timeout_skb() suggests: the usefulness of this feature is questionable. It also wastes cycles walking the sack scoreboard and is actually harmful because of false recovery. It's time to remove this. Signed-off-by: Yuchung Cheng Acked-by: Eric Dumazet Acked-by: Neal Cardwell Acked-by: Nandita Dukkipati Signed-off-by: David S. Miller --- include/linux/tcp.h | 1 - 1 file changed, 1 deletion(-) (limited to 'include/linux') diff --git a/include/linux/tcp.h b/include/linux/tcp.h index 5adbc33..472120b 100644 --- a/include/linux/tcp.h +++ b/include/linux/tcp.h @@ -246,7 +246,6 @@ struct tcp_sock { /* from STCP, retrans queue hinting */ struct sk_buff* lost_skb_hint; - struct sk_buff *scoreboard_skb_hint; struct sk_buff *retransmit_skb_hint; struct sk_buff_head out_of_order_queue; /* Out of order segments go here */ -- cgit v1.1 From 164954454a4b1000eb022415654001cceb9259a7 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Fri, 17 May 2013 16:57:37 +0000 Subject: filter: do not output bpf image address for security reason Do not leak starting address of BPF JIT code for non root users, as it might help intruders to perform an attack. Signed-off-by: Eric Dumazet Cc: Ben Hutchings Cc: Daniel Borkmann Signed-off-by: David S. Miller --- include/linux/filter.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include/linux') diff --git a/include/linux/filter.h b/include/linux/filter.h index c050dcc..56a6b7f 100644 --- a/include/linux/filter.h +++ b/include/linux/filter.h @@ -58,10 +58,10 @@ extern void bpf_jit_free(struct sk_filter *fp); static inline void bpf_jit_dump(unsigned int flen, unsigned int proglen, u32 pass, void *image) { - pr_err("flen=%u proglen=%u pass=%u image=%p\n", + pr_err("flen=%u proglen=%u pass=%u image=%pK\n", flen, proglen, pass, image); if (image) - print_hex_dump(KERN_ERR, "JIT code: ", DUMP_PREFIX_ADDRESS, + print_hex_dump(KERN_ERR, "JIT code: ", DUMP_PREFIX_OFFSET, 16, 1, image, proglen, false); } #define SK_RUN_FILTER(FILTER, SKB) (*FILTER->bpf_func)(SKB, FILTER->insns) -- cgit v1.1 From 99bbc70741903c063b3ccad90a3e06fc55df9245 Mon Sep 17 00:00:00 2001 From: Willem de Bruijn Date: Mon, 20 May 2013 04:02:32 +0000 Subject: rps: selective flow shedding during softnet overflow A cpu executing the network receive path sheds packets when its input queue grows to netdev_max_backlog. A single high rate flow (such as a spoofed source DoS) can exceed a single cpu processing rate and will degrade throughput of other flows hashed onto the same cpu. This patch adds a more fine grained hashtable. If the netdev backlog is above a threshold, IRQ cpus track the ratio of total traffic of each flow (using 4096 buckets, configurable). The ratio is measured by counting the number of packets per flow over the last 256 packets from the source cpu. Any flow that occupies a large fraction of this (set at 50%) will see packet drop while above the threshold. Tested: Setup is a muli-threaded UDP echo server with network rx IRQ on cpu0, kernel receive (RPS) on cpu0 and application threads on cpus 2--7 each handling 20k req/s. Throughput halves when hit with a 400 kpps antagonist storm. With this patch applied, antagonist overload is dropped and the server processes its complete load. The patch is effective when kernel receive processing is the bottleneck. The above RPS scenario is a extreme, but the same is reached with RFS and sufficient kernel processing (iptables, packet socket tap, ..). Signed-off-by: Willem de Bruijn Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- include/linux/netdevice.h | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) (limited to 'include/linux') diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index a94a5a0..7dd535d 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -1778,6 +1778,19 @@ static inline int unregister_gifconf(unsigned int family) return register_gifconf(family, NULL); } +#ifdef CONFIG_NET_FLOW_LIMIT +#define FLOW_LIMIT_HISTORY (1 << 8) /* must be ^2 */ +struct sd_flow_limit { + u64 count; + unsigned int num_buckets; + unsigned int history_head; + u16 history[FLOW_LIMIT_HISTORY]; + u8 buckets[]; +}; + +extern int netdev_flow_limit_table_len; +#endif /* CONFIG_NET_FLOW_LIMIT */ + /* * Incoming packets are placed on per-cpu queues */ @@ -1807,6 +1820,10 @@ struct softnet_data { unsigned int dropped; struct sk_buff_head input_pkt_queue; struct napi_struct backlog; + +#ifdef CONFIG_NET_FLOW_LIMIT + struct sd_flow_limit *flow_limit; +#endif }; static inline void input_queue_head_incr(struct softnet_data *sd) -- cgit v1.1 From 2c7b49212a86f13697281a4dace2cb96aec71d6b Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Sun, 19 May 2013 22:53:42 +0000 Subject: phy: fix the use of PHY_IGNORE_INTERRUPT When a PHY device is registered with the special IRQ value PHY_IGNORE_INTERRUPT (-2) it will not properly be handled by the PHY library: - it continues to poll its register, while we do not want this because such PHY link events or register changes are serviced by an Ethernet MAC - it will still try to configure PHY interrupts at the PHY level, such interrupts do not exist at the PHY but at the MAC level - the state machine only handles PHY_POLL, but should also handle PHY_IGNORE_INTERRUPT similarly This patch updates the PHY state machine and initialization paths to account for the specific PHY_IGNORE_INTERRUPT. Based on an earlier patch by Thomas Petazzoni, and reworked to add the missing bits. Add a helper phy_interrupt_is_valid() which specifically tests for a PHY interrupt not to be PHY_POLL or PHY_IGNORE_INTERRUPT and use it throughout the code. Signed-off-by: Thomas Petazzoni Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- include/linux/phy.h | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'include/linux') diff --git a/include/linux/phy.h b/include/linux/phy.h index 9e11039..8e4bc8a 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -508,6 +508,18 @@ static inline int phy_write(struct phy_device *phydev, u32 regnum, u16 val) return mdiobus_write(phydev->bus, phydev->addr, regnum, val); } +/** + * phy_interrupt_is_valid - Convenience function for testing a given PHY irq + * @phydev: the phy_device struct + * + * NOTE: must be kept in sync with addition/removal of PHY_POLL and + * PHY_IGNORE_INTERRUPT + */ +static inline bool phy_interrupt_is_valid(struct phy_device *phydev) +{ + return phydev->irq != PHY_POLL && phydev->irq != PHY_IGNORE_INTERRUPT; +} + struct phy_device *phy_device_create(struct mii_bus *bus, int addr, int phy_id, bool is_c45, struct phy_c45_device_ids *c45_ids); struct phy_device *get_phy_device(struct mii_bus *bus, int addr, bool is_c45); -- cgit v1.1 From 5ea94e7686a3aa04cc0d01a2d8bd3d0292b3f592 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Sun, 19 May 2013 22:53:43 +0000 Subject: phy: add phy_mac_interrupt() to use with PHY_IGNORE_INTERRUPT There is currently no way for an Ethernet MAC driver servicing PHY link interrupts to notify this to the PHY state machine without defining its own state machine. Since most drivers are not so special, introduce a helper: phy_mac_interrupt() which can be called from a link up/down interrupt routine to update the PHY state machine. To avoid code duplication some refactoring has been done to expose the workqueue and its corresponding callback internally. Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- include/linux/phy.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/linux') diff --git a/include/linux/phy.h b/include/linux/phy.h index 8e4bc8a..fdfa115 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -557,6 +557,8 @@ void phy_drivers_unregister(struct phy_driver *drv, int n); int phy_driver_register(struct phy_driver *new_driver); int phy_drivers_register(struct phy_driver *new_driver, int n); void phy_state_machine(struct work_struct *work); +void phy_change(struct work_struct *work); +void phy_mac_interrupt(struct phy_device *phydev, int new_link); void phy_start_machine(struct phy_device *phydev, void (*handler)(struct net_device *)); void phy_stop_machine(struct phy_device *phydev); -- cgit v1.1 From 78e578c5b43c4f274305075c68d055c8d6141fd5 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Mon, 13 May 2013 22:07:53 +0200 Subject: bcma: support SPROM rev 10 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This is pretty much the same as rev 9, there are just 2 extra fields we know about, but are not used/stored yet anyway. Signed-off-by: Rafał Miłecki Signed-off-by: John W. Linville --- include/linux/ssb/ssb_regs.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux') diff --git a/include/linux/ssb/ssb_regs.h b/include/linux/ssb/ssb_regs.h index 3a72569..f9f931c 100644 --- a/include/linux/ssb/ssb_regs.h +++ b/include/linux/ssb/ssb_regs.h @@ -172,6 +172,7 @@ #define SSB_SPROMSIZE_WORDS_R4 220 #define SSB_SPROMSIZE_BYTES_R123 (SSB_SPROMSIZE_WORDS_R123 * sizeof(u16)) #define SSB_SPROMSIZE_BYTES_R4 (SSB_SPROMSIZE_WORDS_R4 * sizeof(u16)) +#define SSB_SPROMSIZE_WORDS_R10 230 #define SSB_SPROM_BASE1 0x1000 #define SSB_SPROM_BASE31 0x0800 #define SSB_SPROM_REVISION 0x007E -- cgit v1.1 From 6d11cfdba52af08b889fd6d3ee4212930493eb38 Mon Sep 17 00:00:00 2001 From: Pablo Neira Ayuso Date: Wed, 22 May 2013 22:42:36 +0000 Subject: netfilter: don't panic on error while walking through the init path Don't panic if we hit an error while adding the nf_log or pernet netfilter support, just bail out. Signed-off-by: Pablo Neira Ayuso Acked-by: Gao feng --- include/linux/netfilter.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/linux') diff --git a/include/linux/netfilter.h b/include/linux/netfilter.h index 0060fde..de70f7b 100644 --- a/include/linux/netfilter.h +++ b/include/linux/netfilter.h @@ -35,7 +35,7 @@ static inline void nf_inet_addr_mask(const union nf_inet_addr *a1, result->all[3] = a1->all[3] & mask->all[3]; } -extern void netfilter_init(void); +extern int netfilter_init(void); /* Largest hook number + 1 */ #define NF_MAX_HOOKS 8 -- cgit v1.1 From f6f3c437d09e2f62533034e67bfb4385191e992c Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Wed, 22 May 2013 14:50:31 +0900 Subject: sched: add cond_resched_rcu() helper This is intended for use in loops which read data protected by RCU and may have a large number of iterations. Such an example is dumping the list of connections known to IPVS: ip_vs_conn_array() and ip_vs_conn_seq_next(). The benefits are for CONFIG_PREEMPT_RCU=y where we save CPU cycles by moving rcu_read_lock and rcu_read_unlock out of large loops but still allowing the current task to be preempted after every loop iteration for the CONFIG_PREEMPT_RCU=n case. The call to cond_resched() is not needed when CONFIG_PREEMPT_RCU=y. Thanks to Paul E. McKenney for explaining this and for the final version that checks the context with CONFIG_DEBUG_ATOMIC_SLEEP=y for all possible configurations. The function can be empty in the CONFIG_PREEMPT_RCU case, rcu_read_lock and rcu_read_unlock are not needed in this case because the task can be preempted on indication from scheduler. Thanks to Peter Zijlstra for catching this and for his help in trying a solution that changes __might_sleep. Initial cond_resched_rcu_lock() function suggested by Eric Dumazet. Tested-by: Julian Anastasov Signed-off-by: Julian Anastasov Signed-off-by: Simon Horman Acked-by: Peter Zijlstra Signed-off-by: Pablo Neira Ayuso --- include/linux/sched.h | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'include/linux') diff --git a/include/linux/sched.h b/include/linux/sched.h index 178a8d9..4ff8da1 100644 --- a/include/linux/sched.h +++ b/include/linux/sched.h @@ -2444,6 +2444,15 @@ extern int __cond_resched_softirq(void); __cond_resched_softirq(); \ }) +static inline void cond_resched_rcu(void) +{ +#if defined(CONFIG_DEBUG_ATOMIC_SLEEP) || !defined(CONFIG_PREEMPT_RCU) + rcu_read_unlock(); + cond_resched(); + rcu_read_lock(); +#endif +} + /* * Does a critical section need to be broken due to another * task waiting?: (technically does not depend on CONFIG_PREEMPT, -- cgit v1.1 From 42e52bf9e3ae80fd44b21ddfcd64c54e6db2ff76 Mon Sep 17 00:00:00 2001 From: Jiri Pirko Date: Sat, 25 May 2013 04:12:10 +0000 Subject: net: add netnotifier event for upper device change Now when upper device is changed, event is not propagated via RT Netlink to userspace. Userspace might never now about the change. Fix this by adding upper-device-change notifier event. Signed-off-by: Jiri Pirko Signed-off-by: David S. Miller --- include/linux/netdevice.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux') diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 0ebd63a..ea7b6bc 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -1593,6 +1593,7 @@ struct packet_offload { #define NETDEV_RELEASE 0x0012 #define NETDEV_NOTIFY_PEERS 0x0013 #define NETDEV_JOIN 0x0014 +#define NETDEV_CHANGEUPPER 0x0015 extern int register_netdevice_notifier(struct notifier_block *nb); extern int unregister_netdevice_notifier(struct notifier_block *nb); -- cgit v1.1 From 4284b6a535a9aab33e5f3c37929143508dd2ee60 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Thu, 23 May 2013 01:11:12 +0000 Subject: phy: allow drivers to flag a PHY device as internal libphy currently always reports a PHY as an external transceiver from the ethtool output. This is inaccurate, because some drivers should be able to tell that a PHY device is an internal transceiver of an Ethernet MAC. Add a new flag (PHY_IS_INTERNAL) which can be set by PHY drivers just like other flags, and a corresponding helper: phy_is_internal() which can be used by networking drivers to query if a given PHY device is internal. Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- include/linux/phy.h | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'include/linux') diff --git a/include/linux/phy.h b/include/linux/phy.h index fdfa115..ee411b0 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -49,6 +49,7 @@ #define PHY_HAS_INTERRUPT 0x00000001 #define PHY_HAS_MAGICANEG 0x00000002 +#define PHY_IS_INTERNAL 0x00000004 /* Interface Mode definitions */ typedef enum { @@ -261,6 +262,7 @@ struct phy_c45_device_ids { * phy_id: UID for this device found during discovery * c45_ids: 802.3-c45 Device Identifers if is_c45. * is_c45: Set to true if this phy uses clause 45 addressing. + * is_internal: Set to true if this phy is internal to a MAC. * state: state of the PHY for management purposes * dev_flags: Device-specific flags used by the PHY driver. * addr: Bus address of PHY @@ -298,6 +300,7 @@ struct phy_device { struct phy_c45_device_ids c45_ids; bool is_c45; + bool is_internal; enum phy_state state; @@ -520,6 +523,15 @@ static inline bool phy_interrupt_is_valid(struct phy_device *phydev) return phydev->irq != PHY_POLL && phydev->irq != PHY_IGNORE_INTERRUPT; } +/** + * phy_is_internal - Convenience function for testing if a PHY is internal + * @phydev: the phy_device struct + */ +static inline bool phy_is_internal(struct phy_device *phydev) +{ + return phydev->is_internal; +} + struct phy_device *phy_device_create(struct mii_bus *bus, int addr, int phy_id, bool is_c45, struct phy_c45_device_ids *c45_ids); struct phy_device *get_phy_device(struct mii_bus *bus, int addr, bool is_c45); -- cgit v1.1 From 1a37e412a0225fcba5587f24c0dfc7636efc8b69 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Thu, 23 May 2013 21:02:51 +0000 Subject: net: Use 16bits for *_headers fields of struct skbuff In order to mitigate ongoing incresase in the size of struct skbuff use 16 bit integer offsets rather than pointers for inner_*_headers. This appears to reduce the size of struct skbuff from 0xd0 to 0xc0 bytes on x86_64 with the following all unset. CONFIG_XFRM CONFIG_NF_CONNTRACK CONFIG_NF_CONNTRACK_MODULE NET_SKBUFF_NF_DEFRAG_NEEDED CONFIG_BRIDGE_NETFILTER CONFIG_NET_SCHED CONFIG_IPV6_NDISC_NODETYPE CONFIG_NET_DMA CONFIG_NETWORK_SECMARK Signed-off-by: Simon Horman Signed-off-by: David S. Miller --- include/linux/skbuff.h | 119 +++---------------------------------------------- 1 file changed, 6 insertions(+), 113 deletions(-) (limited to 'include/linux') diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h index 2e0ced1..5663e35 100644 --- a/include/linux/skbuff.h +++ b/include/linux/skbuff.h @@ -509,12 +509,12 @@ struct sk_buff { __u32 reserved_tailroom; }; - sk_buff_data_t inner_transport_header; - sk_buff_data_t inner_network_header; - sk_buff_data_t inner_mac_header; - sk_buff_data_t transport_header; - sk_buff_data_t network_header; - sk_buff_data_t mac_header; + __u16 inner_transport_header; + __u16 inner_network_header; + __u16 inner_mac_header; + __u16 transport_header; + __u16 network_header; + __u16 mac_header; /* These elements must be at the end, see alloc_skb() for details. */ sk_buff_data_t tail; sk_buff_data_t end; @@ -1527,7 +1527,6 @@ static inline void skb_reset_mac_len(struct sk_buff *skb) skb->mac_len = skb->network_header - skb->mac_header; } -#ifdef NET_SKBUFF_DATA_USES_OFFSET static inline unsigned char *skb_inner_transport_header(const struct sk_buff *skb) { @@ -1638,112 +1637,6 @@ static inline void skb_set_mac_header(struct sk_buff *skb, const int offset) skb->mac_header += offset; } -#else /* NET_SKBUFF_DATA_USES_OFFSET */ -static inline unsigned char *skb_inner_transport_header(const struct sk_buff - *skb) -{ - return skb->inner_transport_header; -} - -static inline void skb_reset_inner_transport_header(struct sk_buff *skb) -{ - skb->inner_transport_header = skb->data; -} - -static inline void skb_set_inner_transport_header(struct sk_buff *skb, - const int offset) -{ - skb->inner_transport_header = skb->data + offset; -} - -static inline unsigned char *skb_inner_network_header(const struct sk_buff *skb) -{ - return skb->inner_network_header; -} - -static inline void skb_reset_inner_network_header(struct sk_buff *skb) -{ - skb->inner_network_header = skb->data; -} - -static inline void skb_set_inner_network_header(struct sk_buff *skb, - const int offset) -{ - skb->inner_network_header = skb->data + offset; -} - -static inline unsigned char *skb_inner_mac_header(const struct sk_buff *skb) -{ - return skb->inner_mac_header; -} - -static inline void skb_reset_inner_mac_header(struct sk_buff *skb) -{ - skb->inner_mac_header = skb->data; -} - -static inline void skb_set_inner_mac_header(struct sk_buff *skb, - const int offset) -{ - skb->inner_mac_header = skb->data + offset; -} -static inline bool skb_transport_header_was_set(const struct sk_buff *skb) -{ - return skb->transport_header != NULL; -} - -static inline unsigned char *skb_transport_header(const struct sk_buff *skb) -{ - return skb->transport_header; -} - -static inline void skb_reset_transport_header(struct sk_buff *skb) -{ - skb->transport_header = skb->data; -} - -static inline void skb_set_transport_header(struct sk_buff *skb, - const int offset) -{ - skb->transport_header = skb->data + offset; -} - -static inline unsigned char *skb_network_header(const struct sk_buff *skb) -{ - return skb->network_header; -} - -static inline void skb_reset_network_header(struct sk_buff *skb) -{ - skb->network_header = skb->data; -} - -static inline void skb_set_network_header(struct sk_buff *skb, const int offset) -{ - skb->network_header = skb->data + offset; -} - -static inline unsigned char *skb_mac_header(const struct sk_buff *skb) -{ - return skb->mac_header; -} - -static inline int skb_mac_header_was_set(const struct sk_buff *skb) -{ - return skb->mac_header != NULL; -} - -static inline void skb_reset_mac_header(struct sk_buff *skb) -{ - skb->mac_header = skb->data; -} - -static inline void skb_set_mac_header(struct sk_buff *skb, const int offset) -{ - skb->mac_header = skb->data + offset; -} -#endif /* NET_SKBUFF_DATA_USES_OFFSET */ - static inline void skb_probe_transport_header(struct sk_buff *skb, const int offset_hint) { -- cgit v1.1 From 0d89d2035fe063461a5ddb609b2c12e7fb006e44 Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Thu, 23 May 2013 21:02:52 +0000 Subject: MPLS: Add limited GSO support In the case where a non-MPLS packet is received and an MPLS stack is added it may well be the case that the original skb is GSO but the NIC used for transmit does not support GSO of MPLS packets. The aim of this code is to provide GSO in software for MPLS packets whose skbs are GSO. SKB Usage: When an implementation adds an MPLS stack to a non-MPLS packet it should do the following to skb metadata: * Set skb->inner_protocol to the old non-MPLS ethertype of the packet. skb->inner_protocol is added by this patch. * Set skb->protocol to the new MPLS ethertype of the packet. * Set skb->network_header to correspond to the end of the L3 header, including the MPLS label stack. I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to kernel" which adds MPLS support to the kernel datapath of Open vSwtich. That patch sets the above requirements in datapath/actions.c:push_mpls() and was used to exercise this code. The datapath patch is against the Open vSwtich tree but it is intended that it be added to the Open vSwtich code present in the mainline Linux kernel at some point. Features: I believe that the approach that I have taken is at least partially consistent with the handling of other protocols. Jesse, I understand that you have some ideas here. I am more than happy to change my implementation. This patch adds dev->mpls_features which may be used by devices to advertise features supported for MPLS packets. A new NETIF_F_MPLS_GSO feature is added for devices which support hardware MPLS GSO offload. Currently no devices support this and MPLS GSO always falls back to software. Alternate Implementation: One possible alternate implementation is to teach netif_skb_features() and skb_network_protocol() about MPLS, in a similar way to their understanding of VLANs. I believe this would avoid the need for net/mpls/mpls_gso.c and in particular the calls to __skb_push() and __skb_push() in mpls_gso_segment(). I have decided on the implementation in this patch as it should not introduce any overhead in the case where mpls_gso is not compiled into the kernel or inserted as a module. MPLS GSO suggested by Jesse Gross. Based in part on "v4 GRE: Add TCP segmentation offload for GRE" by Pravin B Shelar. Cc: Jesse Gross Cc: Pravin B Shelar Signed-off-by: Simon Horman Signed-off-by: David S. Miller --- include/linux/netdev_features.h | 4 +++- include/linux/netdevice.h | 2 ++ include/linux/skbuff.h | 4 ++++ 3 files changed, 9 insertions(+), 1 deletion(-) (limited to 'include/linux') diff --git a/include/linux/netdev_features.h b/include/linux/netdev_features.h index 09906b7..a2a89a5 100644 --- a/include/linux/netdev_features.h +++ b/include/linux/netdev_features.h @@ -43,8 +43,9 @@ enum { NETIF_F_FSO_BIT, /* ... FCoE segmentation */ NETIF_F_GSO_GRE_BIT, /* ... GRE with TSO */ NETIF_F_GSO_UDP_TUNNEL_BIT, /* ... UDP TUNNEL with TSO */ + NETIF_F_GSO_MPLS_BIT, /* ... MPLS segmentation */ /**/NETIF_F_GSO_LAST = /* last bit, see GSO_MASK */ - NETIF_F_GSO_UDP_TUNNEL_BIT, + NETIF_F_GSO_MPLS_BIT, NETIF_F_FCOE_CRC_BIT, /* FCoE CRC32 */ NETIF_F_SCTP_CSUM_BIT, /* SCTP checksum offload */ @@ -107,6 +108,7 @@ enum { #define NETIF_F_RXALL __NETIF_F(RXALL) #define NETIF_F_GSO_GRE __NETIF_F(GSO_GRE) #define NETIF_F_GSO_UDP_TUNNEL __NETIF_F(GSO_UDP_TUNNEL) +#define NETIF_F_GSO_MPLS __NETIF_F(GSO_MPLS) #define NETIF_F_HW_VLAN_STAG_FILTER __NETIF_F(HW_VLAN_STAG_FILTER) #define NETIF_F_HW_VLAN_STAG_RX __NETIF_F(HW_VLAN_STAG_RX) #define NETIF_F_HW_VLAN_STAG_TX __NETIF_F(HW_VLAN_STAG_TX) diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index ea7b6bc..6b2bb46 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -1088,6 +1088,8 @@ struct net_device { * need to set them appropriately. */ netdev_features_t hw_enc_features; + /* mask of fetures inheritable by MPLS */ + netdev_features_t mpls_features; /* Interface index. Unique device identifier */ int ifindex; diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h index 5663e35..8f2b830 100644 --- a/include/linux/skbuff.h +++ b/include/linux/skbuff.h @@ -319,6 +319,8 @@ enum { SKB_GSO_GRE = 1 << 6, SKB_GSO_UDP_TUNNEL = 1 << 7, + + SKB_GSO_MPLS = 1 << 8, }; #if BITS_PER_LONG > 32 @@ -389,6 +391,7 @@ typedef unsigned char *sk_buff_data_t; * @dropcount: total number of sk_receive_queue overflows * @vlan_proto: vlan encapsulation protocol * @vlan_tci: vlan tag control information + * @inner_protocol: Protocol (encapsulation) * @inner_transport_header: Inner transport layer header (encapsulation) * @inner_network_header: Network layer header (encapsulation) * @inner_mac_header: Link layer header (encapsulation) @@ -509,6 +512,7 @@ struct sk_buff { __u32 reserved_tailroom; }; + __be16 inner_protocol; __u16 inner_transport_header; __u16 inner_network_header; __u16 inner_mac_header; -- cgit v1.1 From da6e378ba918cd0feeb90eeb84d8b42148bb0c82 Mon Sep 17 00:00:00 2001 From: dingtianhong Date: Mon, 27 May 2013 19:53:31 +0000 Subject: netpoll: remove return value from netpoll_rx_disable() The netpoll_rx_disable() will always return 0, it is no use and looks wordy, so remove the unnecessary code and get rid of it in _dev_open and _dev_close. Signed-off-by: Ding Tianhong Signed-off-by: David S. Miller --- include/linux/netpoll.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include/linux') diff --git a/include/linux/netpoll.h b/include/linux/netpoll.h index fa2cb76..f3c7c24 100644 --- a/include/linux/netpoll.h +++ b/include/linux/netpoll.h @@ -53,10 +53,10 @@ struct netpoll_info { }; #ifdef CONFIG_NETPOLL -extern int netpoll_rx_disable(struct net_device *dev); +extern void netpoll_rx_disable(struct net_device *dev); extern void netpoll_rx_enable(struct net_device *dev); #else -static inline int netpoll_rx_disable(struct net_device *dev) { return 0; } +static inline void netpoll_rx_disable(struct net_device *dev) { return; } static inline void netpoll_rx_enable(struct net_device *dev) { return; } #endif -- cgit v1.1 From 351638e7deeed2ec8ce451b53d33921b3da68f83 Mon Sep 17 00:00:00 2001 From: Jiri Pirko Date: Tue, 28 May 2013 01:30:21 +0000 Subject: net: pass info struct via netdevice notifier So far, only net_device * could be passed along with netdevice notifier event. This patch provides a possibility to pass custom structure able to provide info that event listener needs to know. Signed-off-by: Jiri Pirko v2->v3: fix typo on simeth shortened dev_getter shortened notifier_info struct name v1->v2: fix notifier_call parameter in call_netdevice_notifier() Signed-off-by: David S. Miller --- include/linux/netdevice.h | 13 +++++++++++++ 1 file changed, 13 insertions(+) (limited to 'include/linux') diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 6b2bb46..13a3484 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -1599,6 +1599,19 @@ struct packet_offload { extern int register_netdevice_notifier(struct notifier_block *nb); extern int unregister_netdevice_notifier(struct notifier_block *nb); + +struct netdev_notifier_info { + struct net_device *dev; +}; + +static inline struct net_device * +netdev_notifier_info_to_dev(const struct netdev_notifier_info *info) +{ + return info->dev; +} + +extern int call_netdevice_notifiers_info(unsigned long val, struct net_device *dev, + struct netdev_notifier_info *info); extern int call_netdevice_notifiers(unsigned long val, struct net_device *dev); -- cgit v1.1 From be9efd3653284f2827fd82861e8e9db9a8f726e1 Mon Sep 17 00:00:00 2001 From: Jiri Pirko Date: Tue, 28 May 2013 01:30:22 +0000 Subject: net: pass changed flags along with NETDEV_CHANGE event MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Use new netdevice notifier infrastructure to pass along changed flags. Signed-off-by: Timo Teräs Signed-off-by: Jiri Pirko v2->v3: shortened notifier_info struct name Signed-off-by: David S. Miller --- include/linux/netdevice.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'include/linux') diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 13a3484..8502718 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -1604,6 +1604,11 @@ struct netdev_notifier_info { struct net_device *dev; }; +struct netdev_notifier_change_info { + struct netdev_notifier_info info; /* must be first */ + unsigned int flags_changed; +}; + static inline struct net_device * netdev_notifier_info_to_dev(const struct netdev_notifier_info *info) { -- cgit v1.1 From 75538c2b85cf22eb9af6adfaf26ed7219025adeb Mon Sep 17 00:00:00 2001 From: Cong Wang Date: Wed, 29 May 2013 11:30:50 +0800 Subject: net: always pass struct netdev_notifier_info to netdevice notifiers commit 351638e7deeed2ec8ce451b53d3 (net: pass info struct via netdevice notifier) breaks booting of my KVM guest, this is due to we still forget to pass struct netdev_notifier_info in several places. This patch completes it. Cc: Jiri Pirko Cc: David S. Miller Signed-off-by: Cong Wang Signed-off-by: David S. Miller --- include/linux/netdevice.h | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'include/linux') diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 8502718..8f967e3 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -1609,6 +1609,12 @@ struct netdev_notifier_change_info { unsigned int flags_changed; }; +static inline void netdev_notifier_info_init(struct netdev_notifier_info *info, + struct net_device *dev) +{ + info->dev = dev; +} + static inline struct net_device * netdev_notifier_info_to_dev(const struct netdev_notifier_info *info) { -- cgit v1.1 From 7cc461900549fc480eb133948649a1edb7eaaa6f Mon Sep 17 00:00:00 2001 From: Simon Horman Date: Tue, 28 May 2013 20:34:29 +0000 Subject: net, ipv4, ipv6: Correct assignment of skb->network_header to skb->tail This corrects an regression introduced by "net: Use 16bits for *_headers fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In that case skb->tail will be a pointer however skb->network_header is now an offset. This patch corrects the problem by adding a wrapper to return skb tail as an offset regardless of the value of NET_SKBUFF_DATA_USES_OFFSET. It seems that skb->tail that this offset may be more than 64k and some care has been taken to treat such cases as an error. Signed-off-by: Simon Horman Signed-off-by: David S. Miller --- include/linux/skbuff.h | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'include/linux') diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h index 8f2b830..5f93119 100644 --- a/include/linux/skbuff.h +++ b/include/linux/skbuff.h @@ -1391,6 +1391,11 @@ static inline void skb_set_tail_pointer(struct sk_buff *skb, const int offset) skb_reset_tail_pointer(skb); skb->tail += offset; } + +static inline unsigned long skb_tail_offset(const struct sk_buff *skb) +{ + return skb->tail; +} #else /* NET_SKBUFF_DATA_USES_OFFSET */ static inline unsigned char *skb_tail_pointer(const struct sk_buff *skb) { @@ -1407,6 +1412,10 @@ static inline void skb_set_tail_pointer(struct sk_buff *skb, const int offset) skb->tail = skb->data + offset; } +static inline unsigned long skb_tail_offset(const struct sk_buff *skb) +{ + return skb->tail - skb->head; +} #endif /* NET_SKBUFF_DATA_USES_OFFSET */ /* -- cgit v1.1 From a910e4a94f6923c8c988565525f017f687bf7205 Mon Sep 17 00:00:00 2001 From: Solomon Peachy Date: Fri, 24 May 2013 20:04:38 -0400 Subject: cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets Signed-off-by: Solomon Peachy Signed-off-by: John W. Linville --- include/linux/cw1200_platform.h | 46 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 46 insertions(+) create mode 100644 include/linux/cw1200_platform.h (limited to 'include/linux') diff --git a/include/linux/cw1200_platform.h b/include/linux/cw1200_platform.h new file mode 100644 index 0000000..c168fa5 --- /dev/null +++ b/include/linux/cw1200_platform.h @@ -0,0 +1,46 @@ +/* + * Copyright (C) ST-Ericsson SA 2011 + * + * Author: Dmitry Tarnyagin + * License terms: GNU General Public License (GPL) version 2 + */ + +#ifndef CW1200_PLAT_H_INCLUDED +#define CW1200_PLAT_H_INCLUDED + +struct cw1200_platform_data_spi { + u8 spi_bits_per_word; /* REQUIRED */ + u16 ref_clk; /* REQUIRED (in KHz) */ + + /* All others are optional */ + bool have_5ghz; + const struct resource *reset; /* GPIO to RSTn signal */ + const struct resource *powerup; /* GPIO to POWERUP signal */ + int (*power_ctrl)(const struct cw1200_platform_data_spi *pdata, + bool enable); /* Control 3v3 / 1v8 supply */ + int (*clk_ctrl)(const struct cw1200_platform_data_spi *pdata, + bool enable); /* Control CLK32K */ + const u8 *macaddr; /* if NULL, use cw1200_mac_template module parameter */ + const char *sdd_file; /* if NULL, will use default for detected hw type */ +}; + +struct cw1200_platform_data_sdio { + u16 ref_clk; /* REQUIRED (in KHz) */ + + /* All others are optional */ + const struct resource *irq; /* if using GPIO for IRQ */ + bool have_5ghz; + bool no_nptb; /* SDIO hardware does not support non-power-of-2-blocksizes */ + const struct resource *reset; /* GPIO to RSTn signal */ + const struct resource *powerup; /* GPIO to POWERUP signal */ + int (*power_ctrl)(const struct cw1200_platform_data_sdio *pdata, + bool enable); /* Control 3v3 / 1v8 supply */ + int (*clk_ctrl)(const struct cw1200_platform_data_sdio *pdata, + bool enable); /* Control CLK32K */ + const u8 *macaddr; /* if NULL, use cw1200_mac_template module parameter */ + const char *sdd_file; /* if NULL, will use default for detected hw type */ +}; + +const void *cw1200_get_platform_data(void); + +#endif /* CW1200_PLAT_H_INCLUDED */ -- cgit v1.1 From 5f292354e7ff69afbe9a272ef997b8f3edaf860a Mon Sep 17 00:00:00 2001 From: Sebastian Hesselbarth Date: Wed, 29 May 2013 09:32:45 +0000 Subject: net: mv643xx_eth: add phy_node to platform_data struct This adds a struct device_node pointer for a phy passed by phandle to mv643xx_eth node. Signed-off-by: Sebastian Hesselbarth Signed-off-by: David S. Miller --- include/linux/mv643xx_eth.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/linux') diff --git a/include/linux/mv643xx_eth.h b/include/linux/mv643xx_eth.h index 141d395..6e8215b 100644 --- a/include/linux/mv643xx_eth.h +++ b/include/linux/mv643xx_eth.h @@ -30,6 +30,7 @@ struct mv643xx_eth_shared_platform_data { #define MV643XX_ETH_PHY_ADDR(x) (0x80 | (x)) #define MV643XX_ETH_PHY_NONE 0xff +struct device_node; struct mv643xx_eth_platform_data { /* * Pointer back to our parent instance, and our port number. @@ -41,6 +42,7 @@ struct mv643xx_eth_platform_data { * Whether a PHY is present, and if yes, at which address. */ int phy_addr; + struct device_node *phy_node; /* * Use this MAC address if it is valid, overriding the -- cgit v1.1 From 3da09a5154edb92fe74c266a4fa900bcbed6d44c Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 30 May 2013 20:08:26 +0000 Subject: phy: Add Marvell 88E1116R phy ID This phy is on Xilinx ZC702 zynq development board. Signed-off-by: Anirudha Sarangi Signed-off-by: Michal Simek Signed-off-by: David S. Miller --- include/linux/marvell_phy.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux') diff --git a/include/linux/marvell_phy.h b/include/linux/marvell_phy.h index dd3c34e..ec41025 100644 --- a/include/linux/marvell_phy.h +++ b/include/linux/marvell_phy.h @@ -14,6 +14,7 @@ #define MARVELL_PHY_ID_88E1149R 0x01410e50 #define MARVELL_PHY_ID_88E1240 0x01410e30 #define MARVELL_PHY_ID_88E1318S 0x01410e90 +#define MARVELL_PHY_ID_88E1116R 0x01410e40 /* struct phy_device dev_flags definitions */ #define MARVELL_PHY_M1145_FLAGS_RESISTANCE 0x00000001 -- cgit v1.1 From 10e24caa98b6dd0d3d8b783453d5c07aa4e9af0c Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 30 May 2013 20:08:27 +0000 Subject: phy: Add Marvell 88E1510 phy ID Add support for this new phy ID. Signed-off-by: Rick Hoover Signed-off-by: Steven Wang Signed-off-by: Lars-Peter Clausen Signed-off-by: Michal Simek Signed-off-by: David S. Miller --- include/linux/marvell_phy.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux') diff --git a/include/linux/marvell_phy.h b/include/linux/marvell_phy.h index ec41025..8e9a029 100644 --- a/include/linux/marvell_phy.h +++ b/include/linux/marvell_phy.h @@ -15,6 +15,7 @@ #define MARVELL_PHY_ID_88E1240 0x01410e30 #define MARVELL_PHY_ID_88E1318S 0x01410e90 #define MARVELL_PHY_ID_88E1116R 0x01410e40 +#define MARVELL_PHY_ID_88E1510 0x01410dd0 /* struct phy_device dev_flags definitions */ #define MARVELL_PHY_M1145_FLAGS_RESISTANCE 0x00000001 -- cgit v1.1 From 35d0461061f27eeb62de63174959edbbb9e434de Mon Sep 17 00:00:00 2001 From: Cong Wang Date: Wed, 29 May 2013 15:16:05 +0800 Subject: net: clean up skb headers code commit 1a37e412a0225fcba5587 (net: Use 16bits for *_headers fields of struct skbuff) converts skb->*_header to u16, some #if NET_SKBUFF_DATA_USES_OFFSET are now useless, and to be safe, we could just use "X = (typeof(X)) ~0U;" as suggested by David. Cc: David S. Miller Cc: Simon Horman Signed-off-by: Cong Wang Signed-off-by: David S. Miller --- include/linux/skbuff.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include/linux') diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h index 5f93119..b999790 100644 --- a/include/linux/skbuff.h +++ b/include/linux/skbuff.h @@ -1593,7 +1593,7 @@ static inline void skb_set_inner_mac_header(struct sk_buff *skb, } static inline bool skb_transport_header_was_set(const struct sk_buff *skb) { - return skb->transport_header != ~0U; + return skb->transport_header != (typeof(skb->transport_header))~0U; } static inline unsigned char *skb_transport_header(const struct sk_buff *skb) @@ -1636,7 +1636,7 @@ static inline unsigned char *skb_mac_header(const struct sk_buff *skb) static inline int skb_mac_header_was_set(const struct sk_buff *skb) { - return skb->mac_header != ~0U; + return skb->mac_header != (typeof(skb->mac_header))~0U; } static inline void skb_reset_mac_header(struct sk_buff *skb) -- cgit v1.1 From 2cc70ba4cf5f97a7cf08063d2fae693d36b462eb Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Tue, 28 May 2013 04:07:21 +0000 Subject: phy: add reverse MII PHY connection type The PHY library currently does not know about the the reverse MII connection type. Add it to the list of supported PHY modes and update of_get_phy_mode() to support it and look for the string "rev-mii". Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- include/linux/phy.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux') diff --git a/include/linux/phy.h b/include/linux/phy.h index ee411b0..64ab823 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -58,6 +58,7 @@ typedef enum { PHY_INTERFACE_MODE_GMII, PHY_INTERFACE_MODE_SGMII, PHY_INTERFACE_MODE_TBI, + PHY_INTERFACE_MODE_REVMII, PHY_INTERFACE_MODE_RMII, PHY_INTERFACE_MODE_RGMII, PHY_INTERFACE_MODE_RGMII_ID, -- cgit v1.1 From e05ecccdf752122a439b03c3190458d2c8f0bac6 Mon Sep 17 00:00:00 2001 From: Jacob Minshall Date: Wed, 29 May 2013 14:32:36 -0700 Subject: mac80211: set mesh formation field properly Cap max peerings at 63 in accordance with IEEE-2012 8.4.2.100.7. Triggers a beacon regeneration every time the number of peerings changes. Previously this would only happen if the "accepting peerings" bit changed. Signed-off-by: Jacob Minshall Signed-off-by: Johannes Berg --- include/linux/ieee80211.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux') diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h index d826e5a..b0dc87a 100644 --- a/include/linux/ieee80211.h +++ b/include/linux/ieee80211.h @@ -146,6 +146,7 @@ static inline u16 ieee80211_sn_sub(u16 sn1, u16 sn2) #define IEEE80211_MAX_RTS_THRESHOLD 2353 #define IEEE80211_MAX_AID 2007 #define IEEE80211_MAX_TIM_LEN 251 +#define IEEE80211_MAX_MESH_PEERINGS 63 /* Maximum size for the MA-UNITDATA primitive, 802.11 standard section 6.2.1.1.2. -- cgit v1.1 From c992219825823cad5e11fab3854eb93df2e9ffa1 Mon Sep 17 00:00:00 2001 From: Solomon Peachy Date: Sun, 2 Jun 2013 09:53:01 -0400 Subject: cw1200: move platform_data header to correct location. (As suggested by Arnd Bergmann) Signed-off-by: Solomon Peachy Signed-off-by: John W. Linville --- include/linux/cw1200_platform.h | 46 --------------------------- include/linux/platform_data/cw1200_platform.h | 46 +++++++++++++++++++++++++++ 2 files changed, 46 insertions(+), 46 deletions(-) delete mode 100644 include/linux/cw1200_platform.h create mode 100644 include/linux/platform_data/cw1200_platform.h (limited to 'include/linux') diff --git a/include/linux/cw1200_platform.h b/include/linux/cw1200_platform.h deleted file mode 100644 index c168fa5..0000000 --- a/include/linux/cw1200_platform.h +++ /dev/null @@ -1,46 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2011 - * - * Author: Dmitry Tarnyagin - * License terms: GNU General Public License (GPL) version 2 - */ - -#ifndef CW1200_PLAT_H_INCLUDED -#define CW1200_PLAT_H_INCLUDED - -struct cw1200_platform_data_spi { - u8 spi_bits_per_word; /* REQUIRED */ - u16 ref_clk; /* REQUIRED (in KHz) */ - - /* All others are optional */ - bool have_5ghz; - const struct resource *reset; /* GPIO to RSTn signal */ - const struct resource *powerup; /* GPIO to POWERUP signal */ - int (*power_ctrl)(const struct cw1200_platform_data_spi *pdata, - bool enable); /* Control 3v3 / 1v8 supply */ - int (*clk_ctrl)(const struct cw1200_platform_data_spi *pdata, - bool enable); /* Control CLK32K */ - const u8 *macaddr; /* if NULL, use cw1200_mac_template module parameter */ - const char *sdd_file; /* if NULL, will use default for detected hw type */ -}; - -struct cw1200_platform_data_sdio { - u16 ref_clk; /* REQUIRED (in KHz) */ - - /* All others are optional */ - const struct resource *irq; /* if using GPIO for IRQ */ - bool have_5ghz; - bool no_nptb; /* SDIO hardware does not support non-power-of-2-blocksizes */ - const struct resource *reset; /* GPIO to RSTn signal */ - const struct resource *powerup; /* GPIO to POWERUP signal */ - int (*power_ctrl)(const struct cw1200_platform_data_sdio *pdata, - bool enable); /* Control 3v3 / 1v8 supply */ - int (*clk_ctrl)(const struct cw1200_platform_data_sdio *pdata, - bool enable); /* Control CLK32K */ - const u8 *macaddr; /* if NULL, use cw1200_mac_template module parameter */ - const char *sdd_file; /* if NULL, will use default for detected hw type */ -}; - -const void *cw1200_get_platform_data(void); - -#endif /* CW1200_PLAT_H_INCLUDED */ diff --git a/include/linux/platform_data/cw1200_platform.h b/include/linux/platform_data/cw1200_platform.h new file mode 100644 index 0000000..c168fa5 --- /dev/null +++ b/include/linux/platform_data/cw1200_platform.h @@ -0,0 +1,46 @@ +/* + * Copyright (C) ST-Ericsson SA 2011 + * + * Author: Dmitry Tarnyagin + * License terms: GNU General Public License (GPL) version 2 + */ + +#ifndef CW1200_PLAT_H_INCLUDED +#define CW1200_PLAT_H_INCLUDED + +struct cw1200_platform_data_spi { + u8 spi_bits_per_word; /* REQUIRED */ + u16 ref_clk; /* REQUIRED (in KHz) */ + + /* All others are optional */ + bool have_5ghz; + const struct resource *reset; /* GPIO to RSTn signal */ + const struct resource *powerup; /* GPIO to POWERUP signal */ + int (*power_ctrl)(const struct cw1200_platform_data_spi *pdata, + bool enable); /* Control 3v3 / 1v8 supply */ + int (*clk_ctrl)(const struct cw1200_platform_data_spi *pdata, + bool enable); /* Control CLK32K */ + const u8 *macaddr; /* if NULL, use cw1200_mac_template module parameter */ + const char *sdd_file; /* if NULL, will use default for detected hw type */ +}; + +struct cw1200_platform_data_sdio { + u16 ref_clk; /* REQUIRED (in KHz) */ + + /* All others are optional */ + const struct resource *irq; /* if using GPIO for IRQ */ + bool have_5ghz; + bool no_nptb; /* SDIO hardware does not support non-power-of-2-blocksizes */ + const struct resource *reset; /* GPIO to RSTn signal */ + const struct resource *powerup; /* GPIO to POWERUP signal */ + int (*power_ctrl)(const struct cw1200_platform_data_sdio *pdata, + bool enable); /* Control 3v3 / 1v8 supply */ + int (*clk_ctrl)(const struct cw1200_platform_data_sdio *pdata, + bool enable); /* Control CLK32K */ + const u8 *macaddr; /* if NULL, use cw1200_mac_template module parameter */ + const char *sdd_file; /* if NULL, will use default for detected hw type */ +}; + +const void *cw1200_get_platform_data(void); + +#endif /* CW1200_PLAT_H_INCLUDED */ -- cgit v1.1 From 6dd64a304eff76ca7dd41bf63df55efa965fa9ec Mon Sep 17 00:00:00 2001 From: Solomon Peachy Date: Sun, 2 Jun 2013 09:53:03 -0400 Subject: cw1200: Replace use of 'struct resource' with 'int' for GPIO fields. The only advantage of 'struct resource' is that it lets us assign names as part of the platform data. Unfortunately since we are using platform data, we are already limited to a single instance of each driver, rendering this moot. So, replace the struct resources with ints, resulting in cleaner code. This was based on a suggestion from Arnd Bergmann. Signed-off-by: Solomon Peachy Signed-off-by: John W. Linville --- include/linux/platform_data/cw1200_platform.h | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) (limited to 'include/linux') diff --git a/include/linux/platform_data/cw1200_platform.h b/include/linux/platform_data/cw1200_platform.h index c168fa5..4454c16 100644 --- a/include/linux/platform_data/cw1200_platform.h +++ b/include/linux/platform_data/cw1200_platform.h @@ -14,8 +14,8 @@ struct cw1200_platform_data_spi { /* All others are optional */ bool have_5ghz; - const struct resource *reset; /* GPIO to RSTn signal */ - const struct resource *powerup; /* GPIO to POWERUP signal */ + int reset; /* GPIO to RSTn signal (0 disables) */ + int powerup; /* GPIO to POWERUP signal (0 disables) */ int (*power_ctrl)(const struct cw1200_platform_data_spi *pdata, bool enable); /* Control 3v3 / 1v8 supply */ int (*clk_ctrl)(const struct cw1200_platform_data_spi *pdata, @@ -28,11 +28,11 @@ struct cw1200_platform_data_sdio { u16 ref_clk; /* REQUIRED (in KHz) */ /* All others are optional */ - const struct resource *irq; /* if using GPIO for IRQ */ bool have_5ghz; - bool no_nptb; /* SDIO hardware does not support non-power-of-2-blocksizes */ - const struct resource *reset; /* GPIO to RSTn signal */ - const struct resource *powerup; /* GPIO to POWERUP signal */ + bool no_nptb; /* SDIO hardware does not support non-power-of-2-blocksizes */ + int reset; /* GPIO to RSTn signal (0 disables) */ + int powerup; /* GPIO to POWERUP signal (0 disables) */ + int irq; /* IRQ line or 0 to use SDIO IRQ */ int (*power_ctrl)(const struct cw1200_platform_data_sdio *pdata, bool enable); /* Control 3v3 / 1v8 supply */ int (*clk_ctrl)(const struct cw1200_platform_data_sdio *pdata, -- cgit v1.1 From 7c0b6f49dbea0b09b1de8aa5c942af9c2ad8b54c Mon Sep 17 00:00:00 2001 From: Solomon Peachy Date: Sun, 2 Jun 2013 11:35:31 -0400 Subject: cw1200: Rework SDIO platform support to prevent build problems. Based on discussions with And Bergmann, this patch changes the SDIO platform code to default to supporting the Sagrad devices, allowing for it to be overridden in board setup code. This renders the cw1200_sagrad module suplerflous, so it is now removed. It also moves the documentation that was in the cw1200_sagrad source to the platform header. Signed-off-by: Solomon Peachy Signed-off-by: John W. Linville --- include/linux/platform_data/cw1200_platform.h | 37 ++++++++++++++++++++++++++- 1 file changed, 36 insertions(+), 1 deletion(-) (limited to 'include/linux') diff --git a/include/linux/platform_data/cw1200_platform.h b/include/linux/platform_data/cw1200_platform.h index 4454c16..c6fbc3c 100644 --- a/include/linux/platform_data/cw1200_platform.h +++ b/include/linux/platform_data/cw1200_platform.h @@ -41,6 +41,41 @@ struct cw1200_platform_data_sdio { const char *sdd_file; /* if NULL, will use default for detected hw type */ }; -const void *cw1200_get_platform_data(void); + +/* An example of SPI support in your board setup file: + + static struct cw1200_platform_data_spi cw1200_platform_data = { + .ref_clk = 38400, + .spi_bits_per_word = 16, + .reset = GPIO_RF_RESET, + .powerup = GPIO_RF_POWERUP, + .macaddr = wifi_mac_addr, + .sdd_file = "sdd_sagrad_1091_1098.bin", + }; + static struct spi_board_info myboard_spi_devices[] __initdata = { + { + .modalias = "cw1200_wlan_spi", + .max_speed_hz = 52000000, + .bus_num = 0, + .irq = WIFI_IRQ, + .platform_data = &cw1200_platform_data, + .chip_select = 0, + }, + }; + + */ + +/* An example of SDIO support in your board setup file: + + static struct cw1200_platform_data_sdio my_cw1200_platform_data = { + .ref_clk = 38400, + .have_5ghz = false, + .sdd_file = "sdd_myplatform.bin", + }; + cw1200_sdio_set_platform_data(&my_cw1200_platform_data); + + */ + +void __init cw1200_sdio_set_platform_data(struct cw1200_platform_data_sdio *pdata); #endif /* CW1200_PLAT_H_INCLUDED */ -- cgit v1.1 From 4da2a54a842db6921289e3e25b0739531a594dea Mon Sep 17 00:00:00 2001 From: Solomon Peachy Date: Sun, 2 Jun 2013 11:35:32 -0400 Subject: cw1200: rename the cw1200 platform definition header My previous patch just moved the file, but it also needed to be renamed to conform to proper conventions. Signed-off-by: Solomon Peachy Signed-off-by: John W. Linville --- include/linux/platform_data/cw1200_platform.h | 81 --------------------------- include/linux/platform_data/net-cw1200.h | 81 +++++++++++++++++++++++++++ 2 files changed, 81 insertions(+), 81 deletions(-) delete mode 100644 include/linux/platform_data/cw1200_platform.h create mode 100644 include/linux/platform_data/net-cw1200.h (limited to 'include/linux') diff --git a/include/linux/platform_data/cw1200_platform.h b/include/linux/platform_data/cw1200_platform.h deleted file mode 100644 index c6fbc3c..0000000 --- a/include/linux/platform_data/cw1200_platform.h +++ /dev/null @@ -1,81 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2011 - * - * Author: Dmitry Tarnyagin - * License terms: GNU General Public License (GPL) version 2 - */ - -#ifndef CW1200_PLAT_H_INCLUDED -#define CW1200_PLAT_H_INCLUDED - -struct cw1200_platform_data_spi { - u8 spi_bits_per_word; /* REQUIRED */ - u16 ref_clk; /* REQUIRED (in KHz) */ - - /* All others are optional */ - bool have_5ghz; - int reset; /* GPIO to RSTn signal (0 disables) */ - int powerup; /* GPIO to POWERUP signal (0 disables) */ - int (*power_ctrl)(const struct cw1200_platform_data_spi *pdata, - bool enable); /* Control 3v3 / 1v8 supply */ - int (*clk_ctrl)(const struct cw1200_platform_data_spi *pdata, - bool enable); /* Control CLK32K */ - const u8 *macaddr; /* if NULL, use cw1200_mac_template module parameter */ - const char *sdd_file; /* if NULL, will use default for detected hw type */ -}; - -struct cw1200_platform_data_sdio { - u16 ref_clk; /* REQUIRED (in KHz) */ - - /* All others are optional */ - bool have_5ghz; - bool no_nptb; /* SDIO hardware does not support non-power-of-2-blocksizes */ - int reset; /* GPIO to RSTn signal (0 disables) */ - int powerup; /* GPIO to POWERUP signal (0 disables) */ - int irq; /* IRQ line or 0 to use SDIO IRQ */ - int (*power_ctrl)(const struct cw1200_platform_data_sdio *pdata, - bool enable); /* Control 3v3 / 1v8 supply */ - int (*clk_ctrl)(const struct cw1200_platform_data_sdio *pdata, - bool enable); /* Control CLK32K */ - const u8 *macaddr; /* if NULL, use cw1200_mac_template module parameter */ - const char *sdd_file; /* if NULL, will use default for detected hw type */ -}; - - -/* An example of SPI support in your board setup file: - - static struct cw1200_platform_data_spi cw1200_platform_data = { - .ref_clk = 38400, - .spi_bits_per_word = 16, - .reset = GPIO_RF_RESET, - .powerup = GPIO_RF_POWERUP, - .macaddr = wifi_mac_addr, - .sdd_file = "sdd_sagrad_1091_1098.bin", - }; - static struct spi_board_info myboard_spi_devices[] __initdata = { - { - .modalias = "cw1200_wlan_spi", - .max_speed_hz = 52000000, - .bus_num = 0, - .irq = WIFI_IRQ, - .platform_data = &cw1200_platform_data, - .chip_select = 0, - }, - }; - - */ - -/* An example of SDIO support in your board setup file: - - static struct cw1200_platform_data_sdio my_cw1200_platform_data = { - .ref_clk = 38400, - .have_5ghz = false, - .sdd_file = "sdd_myplatform.bin", - }; - cw1200_sdio_set_platform_data(&my_cw1200_platform_data); - - */ - -void __init cw1200_sdio_set_platform_data(struct cw1200_platform_data_sdio *pdata); - -#endif /* CW1200_PLAT_H_INCLUDED */ diff --git a/include/linux/platform_data/net-cw1200.h b/include/linux/platform_data/net-cw1200.h new file mode 100644 index 0000000..c6fbc3c --- /dev/null +++ b/include/linux/platform_data/net-cw1200.h @@ -0,0 +1,81 @@ +/* + * Copyright (C) ST-Ericsson SA 2011 + * + * Author: Dmitry Tarnyagin + * License terms: GNU General Public License (GPL) version 2 + */ + +#ifndef CW1200_PLAT_H_INCLUDED +#define CW1200_PLAT_H_INCLUDED + +struct cw1200_platform_data_spi { + u8 spi_bits_per_word; /* REQUIRED */ + u16 ref_clk; /* REQUIRED (in KHz) */ + + /* All others are optional */ + bool have_5ghz; + int reset; /* GPIO to RSTn signal (0 disables) */ + int powerup; /* GPIO to POWERUP signal (0 disables) */ + int (*power_ctrl)(const struct cw1200_platform_data_spi *pdata, + bool enable); /* Control 3v3 / 1v8 supply */ + int (*clk_ctrl)(const struct cw1200_platform_data_spi *pdata, + bool enable); /* Control CLK32K */ + const u8 *macaddr; /* if NULL, use cw1200_mac_template module parameter */ + const char *sdd_file; /* if NULL, will use default for detected hw type */ +}; + +struct cw1200_platform_data_sdio { + u16 ref_clk; /* REQUIRED (in KHz) */ + + /* All others are optional */ + bool have_5ghz; + bool no_nptb; /* SDIO hardware does not support non-power-of-2-blocksizes */ + int reset; /* GPIO to RSTn signal (0 disables) */ + int powerup; /* GPIO to POWERUP signal (0 disables) */ + int irq; /* IRQ line or 0 to use SDIO IRQ */ + int (*power_ctrl)(const struct cw1200_platform_data_sdio *pdata, + bool enable); /* Control 3v3 / 1v8 supply */ + int (*clk_ctrl)(const struct cw1200_platform_data_sdio *pdata, + bool enable); /* Control CLK32K */ + const u8 *macaddr; /* if NULL, use cw1200_mac_template module parameter */ + const char *sdd_file; /* if NULL, will use default for detected hw type */ +}; + + +/* An example of SPI support in your board setup file: + + static struct cw1200_platform_data_spi cw1200_platform_data = { + .ref_clk = 38400, + .spi_bits_per_word = 16, + .reset = GPIO_RF_RESET, + .powerup = GPIO_RF_POWERUP, + .macaddr = wifi_mac_addr, + .sdd_file = "sdd_sagrad_1091_1098.bin", + }; + static struct spi_board_info myboard_spi_devices[] __initdata = { + { + .modalias = "cw1200_wlan_spi", + .max_speed_hz = 52000000, + .bus_num = 0, + .irq = WIFI_IRQ, + .platform_data = &cw1200_platform_data, + .chip_select = 0, + }, + }; + + */ + +/* An example of SDIO support in your board setup file: + + static struct cw1200_platform_data_sdio my_cw1200_platform_data = { + .ref_clk = 38400, + .have_5ghz = false, + .sdd_file = "sdd_myplatform.bin", + }; + cw1200_sdio_set_platform_data(&my_cw1200_platform_data); + + */ + +void __init cw1200_sdio_set_platform_data(struct cw1200_platform_data_sdio *pdata); + +#endif /* CW1200_PLAT_H_INCLUDED */ -- cgit v1.1 From 0e9649c143eb9d7ecaaef221fd411e5c747f97ce Mon Sep 17 00:00:00 2001 From: Jean Sacren Date: Sat, 1 Jun 2013 16:23:16 +0000 Subject: net: do not manually initialize enumerators Clean up unnecessary initialization of enumerators as the compiler takes care of that. Signed-off-by: Jean Sacren Signed-off-by: David S. Miller --- include/linux/net.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'include/linux') diff --git a/include/linux/net.h b/include/linux/net.h index 99c9f0c..4f27575 100644 --- a/include/linux/net.h +++ b/include/linux/net.h @@ -79,9 +79,9 @@ enum sock_type { #endif /* ARCH_HAS_SOCKET_TYPES */ enum sock_shutdown_cmd { - SHUT_RD = 0, - SHUT_WR = 1, - SHUT_RDWR = 2, + SHUT_RD, + SHUT_WR, + SHUT_RDWR, }; struct socket_wq { -- cgit v1.1 From 350e7805706e11fef0bda2ab4b5cd5a0881480b9 Mon Sep 17 00:00:00 2001 From: Daniel Borkmann Date: Thu, 6 Jun 2013 14:08:31 +0000 Subject: net: vlan: minor: remove unused HAVE_VLAN_PUT_TAG Remove the definition of HAVE_VLAN_PUT_TAG since it's not used or exported anywhere. Signed-off-by: Daniel Borkmann Signed-off-by: David S. Miller --- include/linux/if_vlan.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'include/linux') diff --git a/include/linux/if_vlan.h b/include/linux/if_vlan.h index 52bd03b..7a9c8cf 100644 --- a/include/linux/if_vlan.h +++ b/include/linux/if_vlan.h @@ -243,8 +243,6 @@ static inline struct sk_buff *__vlan_hwaccel_put_tag(struct sk_buff *skb, return skb; } -#define HAVE_VLAN_PUT_TAG - /** * vlan_put_tag - inserts VLAN tag according to device features * @skb: skbuff to tag -- cgit v1.1 From 1d2f41ed23343e083566339574807ca7ea75dbba Mon Sep 17 00:00:00 2001 From: Jason Wang Date: Wed, 5 Jun 2013 23:54:35 +0000 Subject: macvlan: switch to use IS_ENABLED() Acked-by: Michael S. Tsirkin Signed-off-by: Jason Wang Signed-off-by: David S. Miller --- include/linux/if_macvlan.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/linux') diff --git a/include/linux/if_macvlan.h b/include/linux/if_macvlan.h index 84dde1d..e47ad46 100644 --- a/include/linux/if_macvlan.h +++ b/include/linux/if_macvlan.h @@ -8,7 +8,7 @@ #include #include -#if defined(CONFIG_MACVTAP) || defined(CONFIG_MACVTAP_MODULE) +#if IS_ENABLED(CONFIG_MACVTAP) struct socket *macvtap_get_socket(struct file *); #else #include -- cgit v1.1 From f0afce01aa639e5164cf73f063b81a8b95619c3a Mon Sep 17 00:00:00 2001 From: Jason Wang Date: Wed, 5 Jun 2013 23:54:37 +0000 Subject: macvlan: change the max number of queues to 16 Macvtap should be at least compatible with tap, so change the max number to 16. Signed-off-by: Jason Wang Acked-by: Michael S. Tsirkin Signed-off-by: David S. Miller --- include/linux/if_macvlan.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/linux') diff --git a/include/linux/if_macvlan.h b/include/linux/if_macvlan.h index e47ad46..62d8bda 100644 --- a/include/linux/if_macvlan.h +++ b/include/linux/if_macvlan.h @@ -50,7 +50,7 @@ struct macvlan_pcpu_stats { * Maximum times a macvtap device can be opened. This can be used to * configure the number of receive queue, e.g. for multiqueue virtio. */ -#define MAX_MACVTAP_QUEUES (NR_CPUS < 16 ? NR_CPUS : 16) +#define MAX_MACVTAP_QUEUES 16 #define MACVLAN_MC_FILTER_BITS 8 #define MACVLAN_MC_FILTER_SZ (1 << MACVLAN_MC_FILTER_BITS) -- cgit v1.1 From 815f236d622721b54f3963ba59dad98b02cdeabf Mon Sep 17 00:00:00 2001 From: Jason Wang Date: Wed, 5 Jun 2013 23:54:39 +0000 Subject: macvtap: add TUNSETQUEUE ioctl This patch adds TUNSETQUEUE ioctl to let userspace can temporarily disable or enable a queue of macvtap. This is used to be compatible at API layer of tuntap to simplify the userspace to manage the queues. This is done through introducing a linked list to track all taps while using vlan->taps array to only track active taps. Signed-off-by: Jason Wang Acked-by: Michael S. Tsirkin Signed-off-by: David S. Miller --- include/linux/if_macvlan.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include/linux') diff --git a/include/linux/if_macvlan.h b/include/linux/if_macvlan.h index 62d8bda..1912133 100644 --- a/include/linux/if_macvlan.h +++ b/include/linux/if_macvlan.h @@ -69,8 +69,12 @@ struct macvlan_dev { u16 flags; int (*receive)(struct sk_buff *skb); int (*forward)(struct net_device *dev, struct sk_buff *skb); + /* This array tracks active taps. */ struct macvtap_queue *taps[MAX_MACVTAP_QUEUES]; + /* This list tracks all taps (both enabled and disabled) */ + struct list_head queue_list; int numvtaps; + int numqueues; int minor; }; -- cgit v1.1 From af12fa6e46aa651e7b86a4c4117b562518fef184 Mon Sep 17 00:00:00 2001 From: Eliezer Tamir Date: Mon, 10 Jun 2013 11:39:41 +0300 Subject: net: add napi_id and hash Adds a napi_id and a hashing mechanism to lookup a napi by id. This will be used by subsequent patches to implement low latency Ethernet device polling. Based on a code sample by Eric Dumazet. Signed-off-by: Eliezer Tamir Signed-off-by: Eric Dumazet Tested-by: Willem de Bruijn Signed-off-by: David S. Miller --- include/linux/netdevice.h | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+) (limited to 'include/linux') diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 8f967e3..39bbd46 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -324,12 +324,15 @@ struct napi_struct { struct sk_buff *gro_list; struct sk_buff *skb; struct list_head dev_list; + struct hlist_node napi_hash_node; + unsigned int napi_id; }; enum { NAPI_STATE_SCHED, /* Poll is scheduled */ NAPI_STATE_DISABLE, /* Disable pending */ NAPI_STATE_NPSVC, /* Netpoll - don't dequeue from poll_list */ + NAPI_STATE_HASHED, /* In NAPI hash */ }; enum gro_result { @@ -446,6 +449,32 @@ extern void __napi_complete(struct napi_struct *n); extern void napi_complete(struct napi_struct *n); /** + * napi_by_id - lookup a NAPI by napi_id + * @napi_id: hashed napi_id + * + * lookup @napi_id in napi_hash table + * must be called under rcu_read_lock() + */ +extern struct napi_struct *napi_by_id(unsigned int napi_id); + +/** + * napi_hash_add - add a NAPI to global hashtable + * @napi: napi context + * + * generate a new napi_id and store a @napi under it in napi_hash + */ +extern void napi_hash_add(struct napi_struct *napi); + +/** + * napi_hash_del - remove a NAPI from global table + * @napi: napi context + * + * Warning: caller must observe rcu grace period + * before freeing memory containing @napi + */ +extern void napi_hash_del(struct napi_struct *napi); + +/** * napi_disable - prevent NAPI from scheduling * @n: napi context * -- cgit v1.1 From 060212928670593fb89243640bf05cf89560b023 Mon Sep 17 00:00:00 2001 From: Eliezer Tamir Date: Mon, 10 Jun 2013 11:39:50 +0300 Subject: net: add low latency socket poll Adds an ndo_ll_poll method and the code that supports it. This method can be used by low latency applications to busy-poll Ethernet device queues directly from the socket code. sysctl_net_ll_poll controls how many microseconds to poll. Default is zero (disabled). Individual protocol support will be added by subsequent patches. Signed-off-by: Alexander Duyck Signed-off-by: Jesse Brandeburg Signed-off-by: Eliezer Tamir Acked-by: Eric Dumazet Tested-by: Willem de Bruijn Signed-off-by: David S. Miller --- include/linux/netdevice.h | 3 +++ include/linux/skbuff.h | 8 ++++++-- 2 files changed, 9 insertions(+), 2 deletions(-) (limited to 'include/linux') diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 39bbd46..2ecb96d 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -972,6 +972,9 @@ struct net_device_ops { gfp_t gfp); void (*ndo_netpoll_cleanup)(struct net_device *dev); #endif +#ifdef CONFIG_NET_LL_RX_POLL + int (*ndo_ll_poll)(struct napi_struct *dev); +#endif int (*ndo_set_vf_mac)(struct net_device *dev, int queue, u8 *mac); int (*ndo_set_vf_vlan)(struct net_device *dev, diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h index 9995834..400d82a 100644 --- a/include/linux/skbuff.h +++ b/include/linux/skbuff.h @@ -386,6 +386,7 @@ typedef unsigned char *sk_buff_data_t; * @no_fcs: Request NIC to treat last 4 bytes as Ethernet FCS * @dma_cookie: a cookie to one of several possible DMA operations * done by skb DMA functions + * @napi_id: id of the NAPI struct this skb came from * @secmark: security marking * @mark: Generic packet mark * @dropcount: total number of sk_receive_queue overflows @@ -500,8 +501,11 @@ struct sk_buff { /* 7/9 bit hole (depending on ndisc_nodetype presence) */ kmemcheck_bitfield_end(flags2); -#ifdef CONFIG_NET_DMA - dma_cookie_t dma_cookie; +#if defined CONFIG_NET_DMA || defined CONFIG_NET_LL_RX_POLL + union { + unsigned int napi_id; + dma_cookie_t dma_cookie; + }; #endif #ifdef CONFIG_NETWORK_SECMARK __u32 secmark; -- cgit v1.1 From 30f3a40f9a2a2869a560a9cb9ef488d10c803e14 Mon Sep 17 00:00:00 2001 From: Cong Wang Date: Wed, 5 Jun 2013 20:14:10 +0800 Subject: net: remove last caller of skb_tail_offset() and itself Similar to the following commits: commit 00f97da17a0c8d656d0c9 (netpoll: fix position of network header) commit 525cebedb32a87fa48584 (pktgen: Fix position of ip and udp header) using skb_tail_offset() seems not correct since the offset is based on head pointer. With the last caller removed, skb_tail_offset() can be killed finally. Cc: Thomas Graf Cc: Daniel Borkmann Cc: David S. Miller Signed-off-by: Cong Wang Signed-off-by: David S. Miller --- include/linux/skbuff.h | 8 -------- 1 file changed, 8 deletions(-) (limited to 'include/linux') diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h index 400d82a..a7393ad 100644 --- a/include/linux/skbuff.h +++ b/include/linux/skbuff.h @@ -1396,10 +1396,6 @@ static inline void skb_set_tail_pointer(struct sk_buff *skb, const int offset) skb->tail += offset; } -static inline unsigned long skb_tail_offset(const struct sk_buff *skb) -{ - return skb->tail; -} #else /* NET_SKBUFF_DATA_USES_OFFSET */ static inline unsigned char *skb_tail_pointer(const struct sk_buff *skb) { @@ -1416,10 +1412,6 @@ static inline void skb_set_tail_pointer(struct sk_buff *skb, const int offset) skb->tail = skb->data + offset; } -static inline unsigned long skb_tail_offset(const struct sk_buff *skb) -{ - return skb->tail - skb->head; -} #endif /* NET_SKBUFF_DATA_USES_OFFSET */ /* -- cgit v1.1 From da12c90e099789a63073fc82a19542ce54d4efb9 Mon Sep 17 00:00:00 2001 From: Gao feng Date: Thu, 6 Jun 2013 14:49:11 +0800 Subject: netlink: Add compare function for netlink_table As we know, netlink sockets are private resource of net namespace, they can communicate with each other only when they in the same net namespace. this works well until we try to add namespace support for other subsystems which use netlink. Don't like ipv4 and route table.., it is not suited to make these subsytems belong to net namespace, Such as audit and crypto subsystems,they are more suitable to user namespace. So we must have the ability to make the netlink sockets in same user namespace can communicate with each other. This patch adds a new function pointer "compare" for netlink_table, we can decide if the netlink sockets can communicate with each other through this netlink_table self-defined compare function. The behavior isn't changed if we don't provide the compare function for netlink_table. Signed-off-by: Gao feng Acked-by: Serge E. Hallyn Signed-off-by: David S. Miller --- include/linux/netlink.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux') diff --git a/include/linux/netlink.h b/include/linux/netlink.h index 6358da5..f78b430 100644 --- a/include/linux/netlink.h +++ b/include/linux/netlink.h @@ -46,6 +46,7 @@ struct netlink_kernel_cfg { void (*input)(struct sk_buff *skb); struct mutex *cb_mutex; void (*bind)(int group); + bool (*compare)(struct net *net, struct sock *sk); }; extern struct sock *__netlink_kernel_create(struct net *net, int unit, -- cgit v1.1 From e9897071350bd9d94a56b5b6f79c85b1a98fc7e7 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Fri, 7 Jun 2013 08:48:57 -0700 Subject: igmp: hash a hash table to speedup ip_check_mc_rcu() After IP route cache removal, multicast applications using a lot of multicast addresses hit a O(N) behavior in ip_check_mc_rcu() Add a per in_device hash table to get faster lookup. This hash table is created only if the number of items in mc_list is above 4. Reported-by: Shawn Bohrer Signed-off-by: Eric Dumazet Tested-by: Shawn Bohrer Reviewed-by: Cong Wang Signed-off-by: David S. Miller --- include/linux/igmp.h | 1 + include/linux/inetdevice.h | 5 +++++ 2 files changed, 6 insertions(+) (limited to 'include/linux') diff --git a/include/linux/igmp.h b/include/linux/igmp.h index 7f2bf15..e3362b5 100644 --- a/include/linux/igmp.h +++ b/include/linux/igmp.h @@ -84,6 +84,7 @@ struct ip_mc_list { struct ip_mc_list *next; struct ip_mc_list __rcu *next_rcu; }; + struct ip_mc_list __rcu *next_hash; struct timer_list timer; int users; atomic_t refcnt; diff --git a/include/linux/inetdevice.h b/include/linux/inetdevice.h index ea1e3b8..b99cd23 100644 --- a/include/linux/inetdevice.h +++ b/include/linux/inetdevice.h @@ -50,12 +50,17 @@ struct ipv4_devconf { DECLARE_BITMAP(state, IPV4_DEVCONF_MAX); }; +#define MC_HASH_SZ_LOG 9 + struct in_device { struct net_device *dev; atomic_t refcnt; int dead; struct in_ifaddr *ifa_list; /* IP ifaddr chain */ + struct ip_mc_list __rcu *mc_list; /* IP multicast filter chain */ + struct ip_mc_list __rcu * __rcu *mc_hash; + int mc_count; /* Number of installed mcasts */ spinlock_t mc_tomb_lock; struct ip_mc_list *mc_tomb; -- cgit v1.1 From dffebd2c5cd528a136b276a2a75c56222312d7a4 Mon Sep 17 00:00:00 2001 From: Narendra K Date: Mon, 10 Jun 2013 19:34:03 +0530 Subject: doc:networking: Update comment for dev_id field in netdevice.h This patch updates the comment for 'dev_id' field in 'include/linux/netdevice.h' to reflect the intended usage of 'dev_id'. References: http://marc.info/?l=linux-netdev&m=136992115300526&w=2 References: http://marc.info/?l=linux-netdev&m=137062569014612&w=2 Signed-off-by: Narendra K Reviewed-by: Ben Hutchings Signed-off-by: David S. Miller --- include/linux/netdevice.h | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'include/linux') diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 2ecb96d..e5d6557 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -1174,8 +1174,10 @@ struct net_device { unsigned char addr_assign_type; /* hw address assignment type */ unsigned char addr_len; /* hardware address length */ unsigned char neigh_priv_len; - unsigned short dev_id; /* for shared network cards */ - + unsigned short dev_id; /* Used to differentiate devices + * that share the same link + * layer address + */ spinlock_t addr_list_lock; struct netdev_hw_addr_list uc; /* Unicast mac addresses */ struct netdev_hw_addr_list mc; /* Multicast mac addresses */ -- cgit v1.1 From d80b35beac78b52faad2359adf6a6b14e2725e51 Mon Sep 17 00:00:00 2001 From: Jiri Pirko Date: Mon, 10 Jun 2013 17:42:24 +0200 Subject: team: use kfree_rcu instead of synchronize_rcu in team_port_dev Signed-off-by: Jiri Pirko Signed-off-by: David S. Miller --- include/linux/if_team.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux') diff --git a/include/linux/if_team.h b/include/linux/if_team.h index 4474557..7054595 100644 --- a/include/linux/if_team.h +++ b/include/linux/if_team.h @@ -69,6 +69,7 @@ struct team_port { s32 priority; /* lower number ~ higher priority */ u16 queue_id; struct list_head qom_list; /* node in queue override mapping list */ + struct rcu_head rcu; long mode_priv[0]; }; -- cgit v1.1 From 735d381fa57c573935d35a24ea271ec99897ac63 Mon Sep 17 00:00:00 2001 From: Jiri Pirko Date: Mon, 10 Jun 2013 17:42:25 +0200 Subject: team: remove synchronize_rcu() called during port disable Check the unlikely case of team->en_port_count == 0 before modulo operation. Signed-off-by: Jiri Pirko Signed-off-by: David S. Miller --- include/linux/if_team.h | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'include/linux') diff --git a/include/linux/if_team.h b/include/linux/if_team.h index 7054595..b662045 100644 --- a/include/linux/if_team.h +++ b/include/linux/if_team.h @@ -229,6 +229,16 @@ static inline struct team_port *team_get_port_by_index(struct team *team, return port; return NULL; } + +static inline int team_num_to_port_index(struct team *team, int num) +{ + int en_port_count = ACCESS_ONCE(team->en_port_count); + + if (unlikely(!en_port_count)) + return 0; + return num % en_port_count; +} + static inline struct team_port *team_get_port_by_index_rcu(struct team *team, int port_index) { -- cgit v1.1 From d9a90a3105eb6ca89aab74223e6526ab4a5e44b5 Mon Sep 17 00:00:00 2001 From: Jason Wang Date: Thu, 13 Jun 2013 14:23:35 +0800 Subject: macvtap: slient sparse warnings This patch silents the following sparse warnings: drivers/net/macvtap.c:98:9: warning: incorrect type in assignment (different address spaces) drivers/net/macvtap.c:98:9: expected struct macvtap_queue * drivers/net/macvtap.c:98:9: got struct macvtap_queue [noderef] * drivers/net/macvtap.c:120:9: warning: incorrect type in assignment (different address spaces) drivers/net/macvtap.c:120:9: expected struct macvtap_queue * drivers/net/macvtap.c:120:9: got struct macvtap_queue [noderef] * drivers/net/macvtap.c:151:22: error: incompatible types in comparison expression (different address spaces) drivers/net/macvtap.c:233:23: error: incompatible types in comparison expression (different address spaces) drivers/net/macvtap.c:243:23: error: incompatible types in comparison expression (different address spaces) drivers/net/macvtap.c:247:15: error: incompatible types in comparison expression (different address spaces) CC [M] drivers/net/macvtap.o drivers/net/macvlan.c:232:24: error: incompatible types in comparison expression (different address spaces) Signed-off-by: Jason Wang Signed-off-by: David S. Miller --- include/linux/if_macvlan.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/linux') diff --git a/include/linux/if_macvlan.h b/include/linux/if_macvlan.h index 1912133..f49a9f6 100644 --- a/include/linux/if_macvlan.h +++ b/include/linux/if_macvlan.h @@ -70,7 +70,7 @@ struct macvlan_dev { int (*receive)(struct sk_buff *skb); int (*forward)(struct net_device *dev, struct sk_buff *skb); /* This array tracks active taps. */ - struct macvtap_queue *taps[MAX_MACVTAP_QUEUES]; + struct macvtap_queue __rcu *taps[MAX_MACVTAP_QUEUES]; /* This list tracks all taps (both enabled and disabled) */ struct list_head queue_list; int numvtaps; -- cgit v1.1 From 5f121b9a83b499a61ed44e5ba619c7de8f7271ad Mon Sep 17 00:00:00 2001 From: Willem de Bruijn Date: Thu, 13 Jun 2013 15:29:38 -0400 Subject: net-rps: fixes for rps flow limit Caught by sparse: - __rcu: missing annotation to sd->flow_limit - __user: direct access in cpumask_scnprintf Also - add endline character when printing bitmap if room in buffer - avoid bucket overflow by reducing FLOW_LIMIT_HISTORY The last item warrants some explanation. The hashtable buckets are subject to overflow if FLOW_LIMIT_HISTORY is larger than or equal to bucket size, since all packets may end up in a single bucket. The current (rather arbitrary) history value of 256 happens to match the buffer size (u8). As a result, with a single flow, the first 128 packets are accepted (correct), the second 128 packets dropped (correct) and then the history[] array has filled, so that each subsequent new packet causes an increment in the bucket for new_flow plus a decrement for old_flow: a steady state. This is fine if packets are dropped, as the steady state goes away as soon as a mix of traffic reappears. But, because the 256th packet overflowed the bucket to 0: no packets are dropped. Instead of explicitly adding an overflow check, this patch changes FLOW_LIMIT_HISTORY to never be able to overflow a single bucket. Reported-by: Fengguang Wu (first item) Signed-off-by: Willem de Bruijn Signed-off-by: David S. Miller --- include/linux/netdevice.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include/linux') diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index e5d6557..8c9fcc4 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -1840,7 +1840,7 @@ static inline int unregister_gifconf(unsigned int family) } #ifdef CONFIG_NET_FLOW_LIMIT -#define FLOW_LIMIT_HISTORY (1 << 8) /* must be ^2 */ +#define FLOW_LIMIT_HISTORY (1 << 7) /* must be ^2 and !overflow buckets */ struct sd_flow_limit { u64 count; unsigned int num_buckets; @@ -1883,7 +1883,7 @@ struct softnet_data { struct napi_struct backlog; #ifdef CONFIG_NET_FLOW_LIMIT - struct sd_flow_limit *flow_limit; + struct sd_flow_limit __rcu *flow_limit; #endif }; -- cgit v1.1 From 1d8faf48c74b8329a0322dc4b2a2030ae5003c86 Mon Sep 17 00:00:00 2001 From: Rony Efraim Date: Thu, 13 Jun 2013 13:19:10 +0300 Subject: net/core: Add VF link state control Add netlink directives and ndo entry to allow for controling VF link, which can be in one of three states: Auto - VF link state reflects the PF link state (default) Up - VF link state is up, traffic from VF to VF works even if the actual PF link is down Down - VF link state is down, no traffic from/to this VF, can be of use while configuring the VF Signed-off-by: Rony Efraim Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- include/linux/if_link.h | 1 + include/linux/netdevice.h | 3 +++ 2 files changed, 4 insertions(+) (limited to 'include/linux') diff --git a/include/linux/if_link.h b/include/linux/if_link.h index c3f817c..a86784d 100644 --- a/include/linux/if_link.h +++ b/include/linux/if_link.h @@ -12,5 +12,6 @@ struct ifla_vf_info { __u32 qos; __u32 tx_rate; __u32 spoofchk; + __u32 linkstate; }; #endif /* _LINUX_IF_LINK_H */ diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 8c9fcc4..09b4188 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -829,6 +829,7 @@ struct netdev_fcoe_hbainfo { * int (*ndo_set_vf_spoofchk)(struct net_device *dev, int vf, bool setting); * int (*ndo_get_vf_config)(struct net_device *dev, * int vf, struct ifla_vf_info *ivf); + * int (*ndo_set_vf_link_state)(struct net_device *dev, int vf, int link_state); * int (*ndo_set_vf_port)(struct net_device *dev, int vf, * struct nlattr *port[]); * int (*ndo_get_vf_port)(struct net_device *dev, int vf, struct sk_buff *skb); @@ -986,6 +987,8 @@ struct net_device_ops { int (*ndo_get_vf_config)(struct net_device *dev, int vf, struct ifla_vf_info *ivf); + int (*ndo_set_vf_link_state)(struct net_device *dev, + int vf, int link_state); int (*ndo_set_vf_port)(struct net_device *dev, int vf, struct nlattr *port[]); -- cgit v1.1 From 948e306d7d645af80ea331b60495710fe4fe12bb Mon Sep 17 00:00:00 2001 From: Rony Efraim Date: Thu, 13 Jun 2013 13:19:11 +0300 Subject: net/mlx4: Add VF link state support Add support to change the link state of VF (vPort) Signed-off-by: Rony Efraim Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- include/linux/mlx4/cmd.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include/linux') diff --git a/include/linux/mlx4/cmd.h b/include/linux/mlx4/cmd.h index adf6e06..8074a97 100644 --- a/include/linux/mlx4/cmd.h +++ b/include/linux/mlx4/cmd.h @@ -237,7 +237,7 @@ int mlx4_set_vf_mac(struct mlx4_dev *dev, int port, int vf, u64 mac); int mlx4_set_vf_vlan(struct mlx4_dev *dev, int port, int vf, u16 vlan, u8 qos); int mlx4_set_vf_spoofchk(struct mlx4_dev *dev, int port, int vf, bool setting); int mlx4_get_vf_config(struct mlx4_dev *dev, int port, int vf, struct ifla_vf_info *ivf); - +int mlx4_set_vf_link_state(struct mlx4_dev *dev, int port, int vf, int link_state); #define MLX4_COMM_GET_IF_REV(cmd_chan_ver) (u8)((cmd_chan_ver) >> 8) -- cgit v1.1 From e570bd0472b10c9f982fdb58eb39c81445cddb5c Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Mon, 17 Jun 2013 19:56:20 +0200 Subject: ssb: add struct for serial flash MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This data allow writing for example MTD driver. Signed-off-by: Rafał Miłecki Signed-off-by: John W. Linville --- include/linux/ssb/ssb_driver_mips.h | 15 +++++++++++++++ 1 file changed, 15 insertions(+) (limited to 'include/linux') diff --git a/include/linux/ssb/ssb_driver_mips.h b/include/linux/ssb/ssb_driver_mips.h index afe79d4..6535e47 100644 --- a/include/linux/ssb/ssb_driver_mips.h +++ b/include/linux/ssb/ssb_driver_mips.h @@ -20,6 +20,18 @@ struct ssb_pflash { u32 window_size; }; +#ifdef CONFIG_SSB_SFLASH +struct ssb_sflash { + bool present; + u32 window; + u32 blocksize; + u16 numblocks; + u32 size; + + void *priv; +}; +#endif + struct ssb_mipscore { struct ssb_device *dev; @@ -27,6 +39,9 @@ struct ssb_mipscore { struct ssb_serial_port serial_ports[4]; struct ssb_pflash pflash; +#ifdef CONFIG_SSB_SFLASH + struct ssb_sflash sflash; +#endif }; extern void ssb_mipscore_init(struct ssb_mipscore *mcore); -- cgit v1.1 From bcbde0d449eda7afa8f63280b165c8300dbd00e2 Mon Sep 17 00:00:00 2001 From: Daniel Borkmann Date: Fri, 21 Jun 2013 19:38:07 +0200 Subject: net: netlink: virtual tap device management Similarly to the networking receive path with ptype_all taps, we add the possibility to register netdevices that are for ARPHRD_NETLINK to the netlink subsystem, so that those can be used for netlink analyzers resp. debuggers. We do not offer a direct callback function as out-of-tree modules could do crap with it. Instead, a netdevice must be registered properly and only receives a clone, managed by the netlink layer. Symbols are exported as GPL-only. Signed-off-by: Daniel Borkmann Signed-off-by: David S. Miller --- include/linux/netlink.h | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'include/linux') diff --git a/include/linux/netlink.h b/include/linux/netlink.h index f78b430..86fde81a 100644 --- a/include/linux/netlink.h +++ b/include/linux/netlink.h @@ -145,4 +145,14 @@ static inline int netlink_dump_start(struct sock *ssk, struct sk_buff *skb, return __netlink_dump_start(ssk, skb, nlh, control); } +struct netlink_tap { + struct net_device *dev; + struct module *module; + struct list_head list; +}; + +extern int netlink_add_tap(struct netlink_tap *nt); +extern int __netlink_remove_tap(struct netlink_tap *nt); +extern int netlink_remove_tap(struct netlink_tap *nt); + #endif /* __LINUX_NETLINK_H */ -- cgit v1.1 From d36f82b2435690d8742235d7bdc5bb5e878077e3 Mon Sep 17 00:00:00 2001 From: Daniel Borkmann Date: Tue, 25 Jun 2013 18:17:26 +0200 Subject: ktime: add ms_to_ktime() and ktime_add_ms() helpers Add two ktime helper functions that i) convert a given msec value to a ktime structure and ii) that adds a msec value to a ktime structure. Signed-off-by: Daniel Borkmann Acked-by: Vlad Yasevich Signed-off-by: David S. Miller --- include/linux/ktime.h | 13 +++++++++++++ 1 file changed, 13 insertions(+) (limited to 'include/linux') diff --git a/include/linux/ktime.h b/include/linux/ktime.h index bbca128..b4fa5e4 100644 --- a/include/linux/ktime.h +++ b/include/linux/ktime.h @@ -323,6 +323,11 @@ static inline ktime_t ktime_add_us(const ktime_t kt, const u64 usec) return ktime_add_ns(kt, usec * 1000); } +static inline ktime_t ktime_add_ms(const ktime_t kt, const u64 msec) +{ + return ktime_add_ns(kt, msec * NSEC_PER_MSEC); +} + static inline ktime_t ktime_sub_us(const ktime_t kt, const u64 usec) { return ktime_sub_ns(kt, usec * 1000); @@ -366,7 +371,15 @@ extern void ktime_get_ts(struct timespec *ts); static inline ktime_t ns_to_ktime(u64 ns) { static const ktime_t ktime_zero = { .tv64 = 0 }; + return ktime_add_ns(ktime_zero, ns); } +static inline ktime_t ms_to_ktime(u64 ms) +{ + static const ktime_t ktime_zero = { .tv64 = 0 }; + + return ktime_add_ms(ktime_zero, ms); +} + #endif -- cgit v1.1 From 2be5c76794b0e570aa87b012df5ac864ce668a74 Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Tue, 25 Jun 2013 16:04:21 -0400 Subject: macvtap: Let TUNSETOFFLOAD actually controll offload features. When the user issues TUNSETOFFLOAD ioctl, macvtap does not do anything other then to verify arguments. This patch adds functionality to allow users to actually control offload features. NETIF_F_GSO and NETIF_F_GRO are always on, but the rest of the features can be controlled. Signed-off-by: Vlad Yasevich Signed-off-by: David S. Miller --- include/linux/if_macvlan.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/linux') diff --git a/include/linux/if_macvlan.h b/include/linux/if_macvlan.h index f49a9f6..ddd33fd 100644 --- a/include/linux/if_macvlan.h +++ b/include/linux/if_macvlan.h @@ -65,6 +65,7 @@ struct macvlan_dev { DECLARE_BITMAP(mc_filter, MACVLAN_MC_FILTER_SZ); + netdev_features_t set_features; enum macvlan_mode mode; u16 flags; int (*receive)(struct sk_buff *skb); @@ -75,6 +76,7 @@ struct macvlan_dev { struct list_head queue_list; int numvtaps; int numqueues; + netdev_features_t tap_features; int minor; }; -- cgit v1.1 From baffd2e8d9a562021f046ed52195aaac91a51412 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Mon, 10 Jun 2013 23:12:58 -0300 Subject: ARM: imx: flexcan: Remove platform file As there are no more users of the flexcan platform file, let's remove it. Cc: Sascha Hauer Acked-by: Shawn Guo Signed-off-by: Fabio Estevam Signed-off-by: Marc Kleine-Budde --- include/linux/can/platform/flexcan.h | 20 -------------------- 1 file changed, 20 deletions(-) delete mode 100644 include/linux/can/platform/flexcan.h (limited to 'include/linux') diff --git a/include/linux/can/platform/flexcan.h b/include/linux/can/platform/flexcan.h deleted file mode 100644 index 72b713a..0000000 --- a/include/linux/can/platform/flexcan.h +++ /dev/null @@ -1,20 +0,0 @@ -/* - * Copyright (C) 2010 Marc Kleine-Budde - * - * This file is released under the GPLv2 - * - */ - -#ifndef __CAN_PLATFORM_FLEXCAN_H -#define __CAN_PLATFORM_FLEXCAN_H - -/** - * struct flexcan_platform_data - flex CAN controller platform data - * @transceiver_enable: - called to power on/off the transceiver - * - */ -struct flexcan_platform_data { - void (*transceiver_switch)(int enable); -}; - -#endif /* __CAN_PLATFORM_FLEXCAN_H */ -- cgit v1.1 From 88f9b65d444794bb607f71644362ba0642585206 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Wed, 26 Jun 2013 10:02:11 +0200 Subject: bcma: add support for BCM43142 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Signed-off-by: Rafał Miłecki Signed-off-by: John W. Linville --- include/linux/bcma/bcma.h | 1 + include/linux/bcma/bcma_driver_chipcommon.h | 55 +++++++++++++++++++++++++++++ 2 files changed, 56 insertions(+) (limited to 'include/linux') diff --git a/include/linux/bcma/bcma.h b/include/linux/bcma/bcma.h index 2e34db8..622fc50 100644 --- a/include/linux/bcma/bcma.h +++ b/include/linux/bcma/bcma.h @@ -144,6 +144,7 @@ struct bcma_host_ops { /* Chip IDs of PCIe devices */ #define BCMA_CHIP_ID_BCM4313 0x4313 +#define BCMA_CHIP_ID_BCM43142 43142 #define BCMA_CHIP_ID_BCM43224 43224 #define BCMA_PKG_ID_BCM43224_FAB_CSM 0x8 #define BCMA_PKG_ID_BCM43224_FAB_SMIC 0xa diff --git a/include/linux/bcma/bcma_driver_chipcommon.h b/include/linux/bcma/bcma_driver_chipcommon.h index b8b09ea..c49e1a1 100644 --- a/include/linux/bcma/bcma_driver_chipcommon.h +++ b/include/linux/bcma/bcma_driver_chipcommon.h @@ -330,6 +330,8 @@ #define BCMA_CC_PMU_CAP 0x0604 /* PMU capabilities */ #define BCMA_CC_PMU_CAP_REVISION 0x000000FF /* Revision mask */ #define BCMA_CC_PMU_STAT 0x0608 /* PMU status */ +#define BCMA_CC_PMU_STAT_EXT_LPO_AVAIL 0x00000100 +#define BCMA_CC_PMU_STAT_WDRESET 0x00000080 #define BCMA_CC_PMU_STAT_INTPEND 0x00000040 /* Interrupt pending */ #define BCMA_CC_PMU_STAT_SBCLKST 0x00000030 /* Backplane clock status? */ #define BCMA_CC_PMU_STAT_HAVEALP 0x00000008 /* ALP available */ @@ -355,6 +357,11 @@ #define BCMA_CC_REGCTL_DATA 0x065C #define BCMA_CC_PLLCTL_ADDR 0x0660 #define BCMA_CC_PLLCTL_DATA 0x0664 +#define BCMA_CC_PMU_STRAPOPT 0x0668 /* (corerev >= 28) */ +#define BCMA_CC_PMU_XTAL_FREQ 0x066C /* (pmurev >= 10) */ +#define BCMA_CC_PMU_XTAL_FREQ_ILPCTL_MASK 0x00001FFF +#define BCMA_CC_PMU_XTAL_FREQ_MEASURE_MASK 0x80000000 +#define BCMA_CC_PMU_XTAL_FREQ_MEASURE_SHIFT 31 #define BCMA_CC_SPROM 0x0800 /* SPROM beginning */ /* NAND flash MLC controller registers (corerev >= 38) */ #define BCMA_CC_NAND_REVISION 0x0C00 @@ -435,6 +442,23 @@ #define BCMA_CC_PMU6_4706_PROC_NDIV_MODE_MASK 0x00000007 #define BCMA_CC_PMU6_4706_PROC_NDIV_MODE_SHIFT 0 +/* PMU rev 15 */ +#define BCMA_CC_PMU15_PLL_PLLCTL0 0 +#define BCMA_CC_PMU15_PLL_PC0_CLKSEL_MASK 0x00000003 +#define BCMA_CC_PMU15_PLL_PC0_CLKSEL_SHIFT 0 +#define BCMA_CC_PMU15_PLL_PC0_FREQTGT_MASK 0x003FFFFC +#define BCMA_CC_PMU15_PLL_PC0_FREQTGT_SHIFT 2 +#define BCMA_CC_PMU15_PLL_PC0_PRESCALE_MASK 0x00C00000 +#define BCMA_CC_PMU15_PLL_PC0_PRESCALE_SHIFT 22 +#define BCMA_CC_PMU15_PLL_PC0_KPCTRL_MASK 0x07000000 +#define BCMA_CC_PMU15_PLL_PC0_KPCTRL_SHIFT 24 +#define BCMA_CC_PMU15_PLL_PC0_FCNTCTRL_MASK 0x38000000 +#define BCMA_CC_PMU15_PLL_PC0_FCNTCTRL_SHIFT 27 +#define BCMA_CC_PMU15_PLL_PC0_FDCMODE_MASK 0x40000000 +#define BCMA_CC_PMU15_PLL_PC0_FDCMODE_SHIFT 30 +#define BCMA_CC_PMU15_PLL_PC0_CTRLBIAS_MASK 0x80000000 +#define BCMA_CC_PMU15_PLL_PC0_CTRLBIAS_SHIFT 31 + /* ALP clock on pre-PMU chips */ #define BCMA_CC_PMU_ALP_CLOCK 20000000 /* HT clock for systems with PMU-enabled chipcommon */ @@ -507,6 +531,37 @@ #define BCMA_CHIPCTL_5357_I2S_PINS_ENABLE BIT(18) #define BCMA_CHIPCTL_5357_I2CSPI_PINS_ENABLE BIT(19) +#define BCMA_RES_4314_LPLDO_PU BIT(0) +#define BCMA_RES_4314_PMU_SLEEP_DIS BIT(1) +#define BCMA_RES_4314_PMU_BG_PU BIT(2) +#define BCMA_RES_4314_CBUCK_LPOM_PU BIT(3) +#define BCMA_RES_4314_CBUCK_PFM_PU BIT(4) +#define BCMA_RES_4314_CLDO_PU BIT(5) +#define BCMA_RES_4314_LPLDO2_LVM BIT(6) +#define BCMA_RES_4314_WL_PMU_PU BIT(7) +#define BCMA_RES_4314_LNLDO_PU BIT(8) +#define BCMA_RES_4314_LDO3P3_PU BIT(9) +#define BCMA_RES_4314_OTP_PU BIT(10) +#define BCMA_RES_4314_XTAL_PU BIT(11) +#define BCMA_RES_4314_WL_PWRSW_PU BIT(12) +#define BCMA_RES_4314_LQ_AVAIL BIT(13) +#define BCMA_RES_4314_LOGIC_RET BIT(14) +#define BCMA_RES_4314_MEM_SLEEP BIT(15) +#define BCMA_RES_4314_MACPHY_RET BIT(16) +#define BCMA_RES_4314_WL_CORE_READY BIT(17) +#define BCMA_RES_4314_ILP_REQ BIT(18) +#define BCMA_RES_4314_ALP_AVAIL BIT(19) +#define BCMA_RES_4314_MISC_PWRSW_PU BIT(20) +#define BCMA_RES_4314_SYNTH_PWRSW_PU BIT(21) +#define BCMA_RES_4314_RX_PWRSW_PU BIT(22) +#define BCMA_RES_4314_RADIO_PU BIT(23) +#define BCMA_RES_4314_VCO_LDO_PU BIT(24) +#define BCMA_RES_4314_AFE_LDO_PU BIT(25) +#define BCMA_RES_4314_RX_LDO_PU BIT(26) +#define BCMA_RES_4314_TX_LDO_PU BIT(27) +#define BCMA_RES_4314_HT_AVAIL BIT(28) +#define BCMA_RES_4314_MACPHY_CLK_AVAIL BIT(29) + /* Data for the PMU, if available. * Check availability with ((struct bcma_chipcommon)->capabilities & BCMA_CC_CAP_PMU) */ -- cgit v1.1 From 3b81a6809480f3fc7d9d06562704c8df18ecec00 Mon Sep 17 00:00:00 2001 From: Franky Lin Date: Wed, 26 Jun 2013 14:20:18 +0200 Subject: brcmfmac: add broken scatter-gather DMA support DMA engine of some old SDIO host controllers require block size alignment for data length of each scatterlist item. This patch introduces an intermediate buffer list to support this kind of platform. It decreases the throughput because of an extra memcpy in critical data path. So don't turn this on unless it's necessary. Reviewed-by: Pieter-Paul Giesberts Reviewed-by: Arend van Spriel Signed-off-by: Franky Lin Signed-off-by: Arend van Spriel Signed-off-by: John W. Linville --- include/linux/platform_data/brcmfmac-sdio.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'include/linux') diff --git a/include/linux/platform_data/brcmfmac-sdio.h b/include/linux/platform_data/brcmfmac-sdio.h index 1ade657..b717499 100644 --- a/include/linux/platform_data/brcmfmac-sdio.h +++ b/include/linux/platform_data/brcmfmac-sdio.h @@ -90,6 +90,10 @@ void __init brcmfmac_init_pdata(void) * oob_irq_nr, oob_irq_flags: the OOB interrupt information. The values are * used for registering the irq using request_irq function. * + * broken_sg_support: flag for broken sg list support of SDIO host controller. + * Set this to true if the SDIO host controller has higher align requirement + * than 32 bytes for each scatterlist item. + * * power_on: This function is called by the brcmfmac when the module gets * loaded. This can be particularly useful for low power devices. The platform * spcific routine may for example decide to power up the complete device. @@ -116,6 +120,7 @@ struct brcmfmac_sdio_platform_data { bool oob_irq_supported; unsigned int oob_irq_nr; unsigned long oob_irq_flags; + bool broken_sg_support; void (*power_on)(void); void (*power_off)(void); void (*reset)(void); -- cgit v1.1 From 621e84d6f373dcb273ebfd772638b8e7dc3c2c48 Mon Sep 17 00:00:00 2001 From: Nicolas Dichtel Date: Wed, 26 Jun 2013 16:11:27 +0200 Subject: dev: introduce skb_scrub_packet() The goal of this new function is to perform all needed cleanup before sending an skb into another netns. Signed-off-by: Nicolas Dichtel Signed-off-by: David S. Miller --- include/linux/skbuff.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux') diff --git a/include/linux/skbuff.h b/include/linux/skbuff.h index a7393ad..6b06023 100644 --- a/include/linux/skbuff.h +++ b/include/linux/skbuff.h @@ -2384,6 +2384,7 @@ extern void skb_split(struct sk_buff *skb, struct sk_buff *skb1, const u32 len); extern int skb_shift(struct sk_buff *tgt, struct sk_buff *skb, int shiftlen); +extern void skb_scrub_packet(struct sk_buff *skb); extern struct sk_buff *skb_segment(struct sk_buff *skb, netdev_features_t features); -- cgit v1.1 From 3a36515f729458c8efa0c124c7262d5843ad5c37 Mon Sep 17 00:00:00 2001 From: Pablo Neira Date: Fri, 28 Jun 2013 03:04:23 +0200 Subject: netlink: fix splat in skb_clone with large messages Since (c05cdb1 netlink: allow large data transfers from user-space), netlink splats if it invokes skb_clone on large netlink skbs since: * skb_shared_info was not correctly initialized. * skb->destructor is not set in the cloned skb. This was spotted by trinity: [ 894.990671] BUG: unable to handle kernel paging request at ffffc9000047b001 [ 894.991034] IP: [] skb_clone+0x24/0xc0 [...] [ 894.991034] Call Trace: [ 894.991034] [] nl_fib_input+0x6a/0x240 [ 894.991034] [] ? _raw_read_unlock+0x26/0x40 [ 894.991034] [] netlink_unicast+0x169/0x1e0 [ 894.991034] [] netlink_sendmsg+0x251/0x3d0 Fix it by: 1) introducing a new netlink_skb_clone function that is used in nl_fib_input, that sets our special skb->destructor in the cloned skb. Moreover, handle the release of the large cloned skb head area in the destructor path. 2) not allowing large skbuffs in the netlink broadcast path. I cannot find any reasonable use of the large data transfer using netlink in that path, moreover this helps to skip extra skb_clone handling. I found two more netlink clients that are cloning the skbs, but they are not in the sendmsg path. Therefore, the sole client cloning that I found seems to be the fib frontend. Thanks to Eric Dumazet for helping to address this issue. Reported-by: Fengguang Wu Signed-off-by: Pablo Neira Ayuso Signed-off-by: David S. Miller --- include/linux/netlink.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'include/linux') diff --git a/include/linux/netlink.h b/include/linux/netlink.h index 86fde81a..7a6c396 100644 --- a/include/linux/netlink.h +++ b/include/linux/netlink.h @@ -85,6 +85,22 @@ int netlink_attachskb(struct sock *sk, struct sk_buff *skb, void netlink_detachskb(struct sock *sk, struct sk_buff *skb); int netlink_sendskb(struct sock *sk, struct sk_buff *skb); +static inline struct sk_buff * +netlink_skb_clone(struct sk_buff *skb, gfp_t gfp_mask) +{ + struct sk_buff *nskb; + + nskb = skb_clone(skb, gfp_mask); + if (!nskb) + return NULL; + + /* This is a large skb, set destructor callback to release head */ + if (is_vmalloc_addr(skb->head)) + nskb->destructor = skb->destructor; + + return nskb; +} + /* * skb should fit one page. This choice is good for headerless malloc. * But we should limit to 8K so that userspace does not have to -- cgit v1.1 From b01978cacfd7e3a4ca703b0e48f2e18de8865df5 Mon Sep 17 00:00:00 2001 From: Jack Morgenstein Date: Thu, 27 Jun 2013 19:05:21 +0300 Subject: net/mlx4_core: Dynamic VST to VST vlan/qos changes Within VST mode, enable modifying the vlan and/or qos for a VF without requiring unbind/rebind. This requires firmware which supports the UPDATE_QP command. (If the command is not available, we fall back to requiring unbind/bind to activate these changes). To avoid race conditions with modify-qp on QPs that are affected by update-qp, this operation is performed on the comm_wq. If the update operation succeeds for all the necessary QPs, a vlan_unregister is performed for the abandoned vlan id. Signed-off-by: Jack Morgenstein Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- include/linux/mlx4/cmd.h | 1 + include/linux/mlx4/device.h | 3 ++- include/linux/mlx4/qp.h | 34 ++++++++++++++++++++++++++++++++++ 3 files changed, 37 insertions(+), 1 deletion(-) (limited to 'include/linux') diff --git a/include/linux/mlx4/cmd.h b/include/linux/mlx4/cmd.h index 8074a97..bb1c809 100644 --- a/include/linux/mlx4/cmd.h +++ b/include/linux/mlx4/cmd.h @@ -111,6 +111,7 @@ enum { MLX4_CMD_INIT2INIT_QP = 0x2d, MLX4_CMD_SUSPEND_QP = 0x32, MLX4_CMD_UNSUSPEND_QP = 0x33, + MLX4_CMD_UPDATE_QP = 0x61, /* special QP and management commands */ MLX4_CMD_CONF_SPECIAL_QP = 0x23, MLX4_CMD_MAD_IFC = 0x24, diff --git a/include/linux/mlx4/device.h b/include/linux/mlx4/device.h index a51b013..52c23a8 100644 --- a/include/linux/mlx4/device.h +++ b/include/linux/mlx4/device.h @@ -157,7 +157,8 @@ enum { MLX4_DEV_CAP_FLAGS2_REASSIGN_MAC_EN = 1LL << 4, MLX4_DEV_CAP_FLAG2_TS = 1LL << 5, MLX4_DEV_CAP_FLAG2_VLAN_CONTROL = 1LL << 6, - MLX4_DEV_CAP_FLAG2_FSM = 1LL << 7 + MLX4_DEV_CAP_FLAG2_FSM = 1LL << 7, + MLX4_DEV_CAP_FLAG2_UPDATE_QP = 1LL << 8 }; enum { diff --git a/include/linux/mlx4/qp.h b/include/linux/mlx4/qp.h index 352eec9..f43e32a 100644 --- a/include/linux/mlx4/qp.h +++ b/include/linux/mlx4/qp.h @@ -206,6 +206,40 @@ struct mlx4_qp_context { u32 reserved5[10]; }; +struct mlx4_update_qp_context { + __be64 qp_mask; + __be64 primary_addr_path_mask; + __be64 secondary_addr_path_mask; + u64 reserved1; + struct mlx4_qp_context qp_context; + u64 reserved2[58]; +}; + +enum { + MLX4_UPD_QP_MASK_PM_STATE = 32, + MLX4_UPD_QP_MASK_VSD = 33, +}; + +enum { + MLX4_UPD_QP_PATH_MASK_PKEY_INDEX = 0 + 32, + MLX4_UPD_QP_PATH_MASK_FSM = 1 + 32, + MLX4_UPD_QP_PATH_MASK_MAC_INDEX = 2 + 32, + MLX4_UPD_QP_PATH_MASK_FVL = 3 + 32, + MLX4_UPD_QP_PATH_MASK_CV = 4 + 32, + MLX4_UPD_QP_PATH_MASK_VLAN_INDEX = 5 + 32, + MLX4_UPD_QP_PATH_MASK_ETH_HIDE_CQE_VLAN = 6 + 32, + MLX4_UPD_QP_PATH_MASK_ETH_TX_BLOCK_UNTAGGED = 7 + 32, + MLX4_UPD_QP_PATH_MASK_ETH_TX_BLOCK_1P = 8 + 32, + MLX4_UPD_QP_PATH_MASK_ETH_TX_BLOCK_TAGGED = 9 + 32, + MLX4_UPD_QP_PATH_MASK_ETH_RX_BLOCK_UNTAGGED = 10 + 32, + MLX4_UPD_QP_PATH_MASK_ETH_RX_BLOCK_1P = 11 + 32, + MLX4_UPD_QP_PATH_MASK_ETH_RX_BLOCK_TAGGED = 12 + 32, + MLX4_UPD_QP_PATH_MASK_FEUP = 13 + 32, + MLX4_UPD_QP_PATH_MASK_SCHED_QUEUE = 14 + 32, + MLX4_UPD_QP_PATH_MASK_IF_COUNTER_INDEX = 15 + 32, + MLX4_UPD_QP_PATH_MASK_FVL_RX = 16 + 32, +}; + enum { /* param3 */ MLX4_STRIP_VLAN = 1 << 30 }; -- cgit v1.1 From 0a6eac24583848490e9a9c02daef5e33c997431f Mon Sep 17 00:00:00 2001 From: Rony Efraim Date: Thu, 27 Jun 2013 19:05:22 +0300 Subject: net/mlx4_core: Add HW enforcement to VF link state When the firmware supports the UPDATE_QP command, if the VF link is disabled, block all QPs opened by the VF, by programming the UPDATE_QP command to drop all RX & TX traffic to/from these QPs. Operates only in VST mode. Signed-off-by: Rony Efraim Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- include/linux/mlx4/qp.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/linux') diff --git a/include/linux/mlx4/qp.h b/include/linux/mlx4/qp.h index f43e32a..262deac 100644 --- a/include/linux/mlx4/qp.h +++ b/include/linux/mlx4/qp.h @@ -152,6 +152,8 @@ enum { /* fl */ }; enum { /* vlan_control */ MLX4_VLAN_CTRL_ETH_TX_BLOCK_TAGGED = 1 << 6, + MLX4_VLAN_CTRL_ETH_TX_BLOCK_PRIO_TAGGED = 1 << 5, /* 802.1p priority tag */ + MLX4_VLAN_CTRL_ETH_TX_BLOCK_UNTAGGED = 1 << 4, MLX4_VLAN_CTRL_ETH_RX_BLOCK_TAGGED = 1 << 2, MLX4_VLAN_CTRL_ETH_RX_BLOCK_PRIO_TAGGED = 1 << 1, /* 802.1p priority tag */ MLX4_VLAN_CTRL_ETH_RX_BLOCK_UNTAGGED = 1 << 0 -- cgit v1.1 From 1bc2774d866444c5b316fd1dc2b782f20c762cf4 Mon Sep 17 00:00:00 2001 From: Eliezer Tamir Date: Tue, 2 Jul 2013 23:22:47 +0300 Subject: net: convert lls to use time_in_range() Time in range will fail safely if we move to a different cpu with an extremely large clock skew. Add time_in_range64() and convert lls to use it. changelog: v2 - fixed double call to sched_clock in can_poll_ll - fixed checkpatchisms Signed-off-by: Eliezer Tamir Signed-off-by: David S. Miller --- include/linux/jiffies.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include/linux') diff --git a/include/linux/jiffies.h b/include/linux/jiffies.h index 8fb8edf..97ba4e7 100644 --- a/include/linux/jiffies.h +++ b/include/linux/jiffies.h @@ -139,6 +139,10 @@ static inline u64 get_jiffies_64(void) ((__s64)(a) - (__s64)(b) >= 0)) #define time_before_eq64(a,b) time_after_eq64(b,a) +#define time_in_range64(a, b, c) \ + (time_after_eq64(a, b) && \ + time_before_eq64(a, c)) + /* * These four macros compare jiffies and 'a' for convenience. */ -- cgit v1.1 From 0e0764715d8116484d808f5b3985ca043080788e Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Thu, 4 Jul 2013 10:35:48 +0100 Subject: dt:net:stmmac: Add dt specific phy reset callback support. This patch adds phy reset callback support for stmmac driver via device trees. It adds three new properties to gmac device tree bindings to define the reset signal via gpio. With this patch users can conveniently pass reset gpio number with pre, pulse and post delay in micro secs via DTs. active low: _________ ____________ | | | | |_______________| active high: ________________ | | | | ________| |___________ Signed-off-by: Srinivas Kandagatla Signed-off-by: David S. Miller --- include/linux/stmmac.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include/linux') diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h index c1b3ed3..9e495d31 100644 --- a/include/linux/stmmac.h +++ b/include/linux/stmmac.h @@ -80,6 +80,10 @@ struct stmmac_mdio_bus_data { unsigned int phy_mask; int *irqs; int probed_phy_irq; +#ifdef CONFIG_OF + int reset_gpio, active_low; + u32 delays[3]; +#endif }; struct stmmac_dma_cfg { -- cgit v1.1 From cc229884d3f77ec3b1240e467e0236c3e0647c0c Mon Sep 17 00:00:00 2001 From: "Michael S. Tsirkin" Date: Tue, 9 Jul 2013 13:19:18 +0300 Subject: virtio: support unlocked queue poll This adds a way to check ring empty state after enable_cb outside any locks. Will be used by virtio_net. Note: there's room for more optimization: caller is likely to have a memory barrier already, which means we might be able to get rid of a barrier here. Deferring this optimization until we do some benchmarking. Signed-off-by: Michael S. Tsirkin Signed-off-by: David S. Miller --- include/linux/virtio.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include/linux') diff --git a/include/linux/virtio.h b/include/linux/virtio.h index 9ff8645..72398ee 100644 --- a/include/linux/virtio.h +++ b/include/linux/virtio.h @@ -70,6 +70,10 @@ void virtqueue_disable_cb(struct virtqueue *vq); bool virtqueue_enable_cb(struct virtqueue *vq); +unsigned virtqueue_enable_cb_prepare(struct virtqueue *vq); + +bool virtqueue_poll(struct virtqueue *vq, unsigned); + bool virtqueue_enable_cb_delayed(struct virtqueue *vq); void *virtqueue_detach_unused_buf(struct virtqueue *vq); -- cgit v1.1