From 0335a9554b4d6acc2d17efe752bff54ce59b57eb Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Mon, 14 Aug 2017 18:34:22 +0200 Subject: mfd: dm355evm_msp: Move header file out of I2C realm include/linux/i2c is not for client devices. Move the header file to a more appropriate location. Signed-off-by: Wolfram Sang Acked-by: Alexandre Belloni Acked-by: Dmitry Torokhov Signed-off-by: Lee Jones --- include/linux/mfd/dm355evm_msp.h | 79 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 79 insertions(+) create mode 100644 include/linux/mfd/dm355evm_msp.h (limited to 'include/linux/mfd') diff --git a/include/linux/mfd/dm355evm_msp.h b/include/linux/mfd/dm355evm_msp.h new file mode 100644 index 0000000..3724703 --- /dev/null +++ b/include/linux/mfd/dm355evm_msp.h @@ -0,0 +1,79 @@ +/* + * dm355evm_msp.h - support MSP430 microcontroller on DM355EVM board + */ +#ifndef __LINUX_I2C_DM355EVM_MSP +#define __LINUX_I2C_DM355EVM_MSP + +/* + * Written against Spectrum's writeup for the A4 firmware revision, + * and tweaked to match source and rev D2 schematics by removing CPLD + * and NOR flash hooks (which were last appropriate in rev B boards). + * + * Note that the firmware supports a flavor of write posting ... to be + * sure a write completes, issue another read or write. + */ + +/* utilities to access "registers" emulated by msp430 firmware */ +extern int dm355evm_msp_write(u8 value, u8 reg); +extern int dm355evm_msp_read(u8 reg); + + +/* command/control registers */ +#define DM355EVM_MSP_COMMAND 0x00 +# define MSP_COMMAND_NULL 0 +# define MSP_COMMAND_RESET_COLD 1 +# define MSP_COMMAND_RESET_WARM 2 +# define MSP_COMMAND_RESET_WARM_I 3 +# define MSP_COMMAND_POWEROFF 4 +# define MSP_COMMAND_IR_REINIT 5 +#define DM355EVM_MSP_STATUS 0x01 +# define MSP_STATUS_BAD_OFFSET BIT(0) +# define MSP_STATUS_BAD_COMMAND BIT(1) +# define MSP_STATUS_POWER_ERROR BIT(2) +# define MSP_STATUS_RXBUF_OVERRUN BIT(3) +#define DM355EVM_MSP_RESET 0x02 /* 0 bits == in reset */ +# define MSP_RESET_DC5 BIT(0) +# define MSP_RESET_TVP5154 BIT(2) +# define MSP_RESET_IMAGER BIT(3) +# define MSP_RESET_ETHERNET BIT(4) +# define MSP_RESET_SYS BIT(5) +# define MSP_RESET_AIC33 BIT(7) + +/* GPIO registers ... bit patterns mostly match the source MSP ports */ +#define DM355EVM_MSP_LED 0x03 /* active low (MSP P4) */ +#define DM355EVM_MSP_SWITCH1 0x04 /* (MSP P5, masked) */ +# define MSP_SWITCH1_SW6_1 BIT(0) +# define MSP_SWITCH1_SW6_2 BIT(1) +# define MSP_SWITCH1_SW6_3 BIT(2) +# define MSP_SWITCH1_SW6_4 BIT(3) +# define MSP_SWITCH1_J1 BIT(4) /* NTSC/PAL */ +# define MSP_SWITCH1_MSP_INT BIT(5) /* active low */ +#define DM355EVM_MSP_SWITCH2 0x05 /* (MSP P6, masked) */ +# define MSP_SWITCH2_SW10 BIT(3) +# define MSP_SWITCH2_SW11 BIT(4) +# define MSP_SWITCH2_SW12 BIT(5) +# define MSP_SWITCH2_SW13 BIT(6) +# define MSP_SWITCH2_SW14 BIT(7) +#define DM355EVM_MSP_SDMMC 0x06 /* (MSP P2, masked) */ +# define MSP_SDMMC_0_WP BIT(1) +# define MSP_SDMMC_0_CD BIT(2) /* active low */ +# define MSP_SDMMC_1_WP BIT(3) +# define MSP_SDMMC_1_CD BIT(4) /* active low */ +#define DM355EVM_MSP_FIRMREV 0x07 /* not a GPIO (out of order) */ +#define DM355EVM_MSP_VIDEO_IN 0x08 /* (MSP P3, masked) */ +# define MSP_VIDEO_IMAGER BIT(7) /* low == tvp5146 */ + +/* power supply registers are currently omitted */ + +/* RTC registers */ +#define DM355EVM_MSP_RTC_0 0x12 /* LSB */ +#define DM355EVM_MSP_RTC_1 0x13 +#define DM355EVM_MSP_RTC_2 0x14 +#define DM355EVM_MSP_RTC_3 0x15 /* MSB */ + +/* input event queue registers; code == ((HIGH << 8) | LOW) */ +#define DM355EVM_MSP_INPUT_COUNT 0x16 /* decrement by reading LOW */ +#define DM355EVM_MSP_INPUT_HIGH 0x17 +#define DM355EVM_MSP_INPUT_LOW 0x18 + +#endif /* __LINUX_I2C_DM355EVM_MSP */ -- cgit v1.1 From 9787076c43a86f3465d46aa344cc3e2f607ae72f Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Mon, 14 Aug 2017 18:34:23 +0200 Subject: mfd: tps65010: Move header file out of I2C realm include/linux/i2c is not for client devices. Move the header file to a more appropriate location. Signed-off-by: Wolfram Sang Acked-by: Greg Kroah-Hartman Acked-by: Krzysztof Kozlowski Acked-by: Bartlomiej Zolnierkiewicz Acked-by: Tony Lindgren Signed-off-by: Lee Jones --- include/linux/mfd/tps65010.h | 205 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 205 insertions(+) create mode 100644 include/linux/mfd/tps65010.h (limited to 'include/linux/mfd') diff --git a/include/linux/mfd/tps65010.h b/include/linux/mfd/tps65010.h new file mode 100644 index 0000000..a1fb9bc --- /dev/null +++ b/include/linux/mfd/tps65010.h @@ -0,0 +1,205 @@ +/* linux/mfd/tps65010.h + * + * Functions to access TPS65010 power management device. + * + * Copyright (C) 2004 Dirk Behme + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#ifndef __LINUX_I2C_TPS65010_H +#define __LINUX_I2C_TPS65010_H + +/* + * ---------------------------------------------------------------------------- + * Registers, all 8 bits + * ---------------------------------------------------------------------------- + */ + +#define TPS_CHGSTATUS 0x01 +# define TPS_CHG_USB (1 << 7) +# define TPS_CHG_AC (1 << 6) +# define TPS_CHG_THERM (1 << 5) +# define TPS_CHG_TERM (1 << 4) +# define TPS_CHG_TAPER_TMO (1 << 3) +# define TPS_CHG_CHG_TMO (1 << 2) +# define TPS_CHG_PRECHG_TMO (1 << 1) +# define TPS_CHG_TEMP_ERR (1 << 0) +#define TPS_REGSTATUS 0x02 +# define TPS_REG_ONOFF (1 << 7) +# define TPS_REG_COVER (1 << 6) +# define TPS_REG_UVLO (1 << 5) +# define TPS_REG_NO_CHG (1 << 4) /* tps65013 */ +# define TPS_REG_PG_LD02 (1 << 3) +# define TPS_REG_PG_LD01 (1 << 2) +# define TPS_REG_PG_MAIN (1 << 1) +# define TPS_REG_PG_CORE (1 << 0) +#define TPS_MASK1 0x03 +#define TPS_MASK2 0x04 +#define TPS_ACKINT1 0x05 +#define TPS_ACKINT2 0x06 +#define TPS_CHGCONFIG 0x07 +# define TPS_CHARGE_POR (1 << 7) /* 65010/65012 */ +# define TPS65013_AUA (1 << 7) /* 65011/65013 */ +# define TPS_CHARGE_RESET (1 << 6) +# define TPS_CHARGE_FAST (1 << 5) +# define TPS_CHARGE_CURRENT (3 << 3) +# define TPS_VBUS_500MA (1 << 2) +# define TPS_VBUS_CHARGING (1 << 1) +# define TPS_CHARGE_ENABLE (1 << 0) +#define TPS_LED1_ON 0x08 +#define TPS_LED1_PER 0x09 +#define TPS_LED2_ON 0x0a +#define TPS_LED2_PER 0x0b +#define TPS_VDCDC1 0x0c +# define TPS_ENABLE_LP (1 << 3) +#define TPS_VDCDC2 0x0d +# define TPS_LP_COREOFF (1 << 7) +# define TPS_VCORE_1_8V (7<<4) +# define TPS_VCORE_1_5V (6 << 4) +# define TPS_VCORE_1_4V (5 << 4) +# define TPS_VCORE_1_3V (4 << 4) +# define TPS_VCORE_1_2V (3 << 4) +# define TPS_VCORE_1_1V (2 << 4) +# define TPS_VCORE_1_0V (1 << 4) +# define TPS_VCORE_0_85V (0 << 4) +# define TPS_VCORE_LP_1_2V (3 << 2) +# define TPS_VCORE_LP_1_1V (2 << 2) +# define TPS_VCORE_LP_1_0V (1 << 2) +# define TPS_VCORE_LP_0_85V (0 << 2) +# define TPS_VIB (1 << 1) +# define TPS_VCORE_DISCH (1 << 0) +#define TPS_VREGS1 0x0e +# define TPS_LDO2_ENABLE (1 << 7) +# define TPS_LDO2_OFF (1 << 6) +# define TPS_VLDO2_3_0V (3 << 4) +# define TPS_VLDO2_2_75V (2 << 4) +# define TPS_VLDO2_2_5V (1 << 4) +# define TPS_VLDO2_1_8V (0 << 4) +# define TPS_LDO1_ENABLE (1 << 3) +# define TPS_LDO1_OFF (1 << 2) +# define TPS_VLDO1_3_0V (3 << 0) +# define TPS_VLDO1_2_75V (2 << 0) +# define TPS_VLDO1_2_5V (1 << 0) +# define TPS_VLDO1_ADJ (0 << 0) +#define TPS_MASK3 0x0f +#define TPS_DEFGPIO 0x10 + +/* + * ---------------------------------------------------------------------------- + * Macros used by exported functions + * ---------------------------------------------------------------------------- + */ + +#define LED1 1 +#define LED2 2 +#define OFF 0 +#define ON 1 +#define BLINK 2 +#define GPIO1 1 +#define GPIO2 2 +#define GPIO3 3 +#define GPIO4 4 +#define LOW 0 +#define HIGH 1 + +/* + * ---------------------------------------------------------------------------- + * Exported functions + * ---------------------------------------------------------------------------- + */ + +/* Draw from VBUS: + * 0 mA -- DON'T DRAW (might supply power instead) + * 100 mA -- usb unit load (slowest charge rate) + * 500 mA -- usb high power (fast battery charge) + */ +extern int tps65010_set_vbus_draw(unsigned mA); + +/* tps65010_set_gpio_out_value parameter: + * gpio: GPIO1, GPIO2, GPIO3 or GPIO4 + * value: LOW or HIGH + */ +extern int tps65010_set_gpio_out_value(unsigned gpio, unsigned value); + +/* tps65010_set_led parameter: + * led: LED1 or LED2 + * mode: ON, OFF or BLINK + */ +extern int tps65010_set_led(unsigned led, unsigned mode); + +/* tps65010_set_vib parameter: + * value: ON or OFF + */ +extern int tps65010_set_vib(unsigned value); + +/* tps65010_set_low_pwr parameter: + * mode: ON or OFF + */ +extern int tps65010_set_low_pwr(unsigned mode); + +/* tps65010_config_vregs1 parameter: + * value to be written to VREGS1 register + * Note: The complete register is written, set all bits you need + */ +extern int tps65010_config_vregs1(unsigned value); + +/* tps65013_set_low_pwr parameter: + * mode: ON or OFF + */ +extern int tps65013_set_low_pwr(unsigned mode); + +/* tps65010_set_vdcdc2 + * value to be written to VDCDC2 + */ +extern int tps65010_config_vdcdc2(unsigned value); + +struct i2c_client; + +/** + * struct tps65010_board - packages GPIO and LED lines + * @base: the GPIO number to assign to GPIO-1 + * @outmask: bit (N-1) is set to allow GPIO-N to be used as an + * (open drain) output + * @setup: optional callback issued once the GPIOs are valid + * @teardown: optional callback issued before the GPIOs are invalidated + * @context: optional parameter passed to setup() and teardown() + * + * Board data may be used to package the GPIO (and LED) lines for use + * in by the generic GPIO and LED frameworks. The first four GPIOs + * starting at gpio_base are GPIO1..GPIO4. The next two are LED1/nPG + * and LED2 (with hardware blinking capability, not currently exposed). + * + * The @setup callback may be used with the kind of board-specific glue + * which hands the (now-valid) GPIOs to other drivers, or which puts + * devices in their initial states using these GPIOs. + */ +struct tps65010_board { + int base; + unsigned outmask; + + int (*setup)(struct i2c_client *client, void *context); + int (*teardown)(struct i2c_client *client, void *context); + void *context; +}; + +#endif /* __LINUX_I2C_TPS65010_H */ + -- cgit v1.1 From 9d6105e19f617406aea46dd19281080c7c5ae0d8 Mon Sep 17 00:00:00 2001 From: Elaine Zhang Date: Mon, 21 Aug 2017 03:28:34 +0200 Subject: mfd: rk808: Fix up the chip id get failed the rk8xx chip id is: ((MSB << 8) | LSB) & 0xfff0 Signed-off-by: Elaine Zhang Signed-off-by: Joseph Chen Signed-off-by: Heiko Stuebner Signed-off-by: Lee Jones --- include/linux/mfd/rk808.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include/linux/mfd') diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h index 83701ef..54feb14 100644 --- a/include/linux/mfd/rk808.h +++ b/include/linux/mfd/rk808.h @@ -298,6 +298,7 @@ enum rk818_reg { #define VOUT_LO_INT BIT(0) #define CLK32KOUT2_EN BIT(0) +#define RK8XX_ID_MSK 0xfff0 enum { BUCK_ILMIN_50MA, BUCK_ILMIN_100MA, -- cgit v1.1 From a5247ca6708ff7dc089d2774c131455774153eb6 Mon Sep 17 00:00:00 2001 From: Elaine Zhang Date: Mon, 21 Aug 2017 03:28:35 +0200 Subject: mfd: rk808: Add rk805 regs addr and ID Signed-off-by: Elaine Zhang Signed-off-by: Joseph Chen Signed-off-by: Heiko Stuebner Signed-off-by: Lee Jones --- include/linux/mfd/rk808.h | 120 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 120 insertions(+) (limited to 'include/linux/mfd') diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h index 54feb14..d315659 100644 --- a/include/linux/mfd/rk808.h +++ b/include/linux/mfd/rk808.h @@ -206,6 +206,97 @@ enum rk818_reg { #define RK818_USB_ILMIN_2000MA 0x7 #define RK818_USB_CHG_SD_VSEL_MASK 0x70 +/* RK805 */ +enum rk805_reg { + RK805_ID_DCDC1, + RK805_ID_DCDC2, + RK805_ID_DCDC3, + RK805_ID_DCDC4, + RK805_ID_LDO1, + RK805_ID_LDO2, + RK805_ID_LDO3, +}; + +/* CONFIG REGISTER */ +#define RK805_VB_MON_REG 0x21 +#define RK805_THERMAL_REG 0x22 + +/* POWER CHANNELS ENABLE REGISTER */ +#define RK805_DCDC_EN_REG 0x23 +#define RK805_SLP_DCDC_EN_REG 0x25 +#define RK805_SLP_LDO_EN_REG 0x26 +#define RK805_LDO_EN_REG 0x27 + +/* BUCK AND LDO CONFIG REGISTER */ +#define RK805_BUCK_LDO_SLP_LP_EN_REG 0x2A +#define RK805_BUCK1_CONFIG_REG 0x2E +#define RK805_BUCK1_ON_VSEL_REG 0x2F +#define RK805_BUCK1_SLP_VSEL_REG 0x30 +#define RK805_BUCK2_CONFIG_REG 0x32 +#define RK805_BUCK2_ON_VSEL_REG 0x33 +#define RK805_BUCK2_SLP_VSEL_REG 0x34 +#define RK805_BUCK3_CONFIG_REG 0x36 +#define RK805_BUCK4_CONFIG_REG 0x37 +#define RK805_BUCK4_ON_VSEL_REG 0x38 +#define RK805_BUCK4_SLP_VSEL_REG 0x39 +#define RK805_LDO1_ON_VSEL_REG 0x3B +#define RK805_LDO1_SLP_VSEL_REG 0x3C +#define RK805_LDO2_ON_VSEL_REG 0x3D +#define RK805_LDO2_SLP_VSEL_REG 0x3E +#define RK805_LDO3_ON_VSEL_REG 0x3F +#define RK805_LDO3_SLP_VSEL_REG 0x40 + +/* INTERRUPT REGISTER */ +#define RK805_PWRON_LP_INT_TIME_REG 0x47 +#define RK805_PWRON_DB_REG 0x48 +#define RK805_DEV_CTRL_REG 0x4B +#define RK805_INT_STS_REG 0x4C +#define RK805_INT_STS_MSK_REG 0x4D +#define RK805_GPIO_IO_POL_REG 0x50 +#define RK805_OUT_REG 0x52 +#define RK805_ON_SOURCE_REG 0xAE +#define RK805_OFF_SOURCE_REG 0xAF + +#define RK805_NUM_REGULATORS 7 + +#define RK805_PWRON_FALL_RISE_INT_EN 0x0 +#define RK805_PWRON_FALL_RISE_INT_MSK 0x81 + +/* RK805 IRQ Definitions */ +#define RK805_IRQ_PWRON_RISE 0 +#define RK805_IRQ_VB_LOW 1 +#define RK805_IRQ_PWRON 2 +#define RK805_IRQ_PWRON_LP 3 +#define RK805_IRQ_HOTDIE 4 +#define RK805_IRQ_RTC_ALARM 5 +#define RK805_IRQ_RTC_PERIOD 6 +#define RK805_IRQ_PWRON_FALL 7 + +#define RK805_IRQ_PWRON_RISE_MSK BIT(0) +#define RK805_IRQ_VB_LOW_MSK BIT(1) +#define RK805_IRQ_PWRON_MSK BIT(2) +#define RK805_IRQ_PWRON_LP_MSK BIT(3) +#define RK805_IRQ_HOTDIE_MSK BIT(4) +#define RK805_IRQ_RTC_ALARM_MSK BIT(5) +#define RK805_IRQ_RTC_PERIOD_MSK BIT(6) +#define RK805_IRQ_PWRON_FALL_MSK BIT(7) + +#define RK805_PWR_RISE_INT_STATUS BIT(0) +#define RK805_VB_LOW_INT_STATUS BIT(1) +#define RK805_PWRON_INT_STATUS BIT(2) +#define RK805_PWRON_LP_INT_STATUS BIT(3) +#define RK805_HOTDIE_INT_STATUS BIT(4) +#define RK805_ALARM_INT_STATUS BIT(5) +#define RK805_PERIOD_INT_STATUS BIT(6) +#define RK805_PWR_FALL_INT_STATUS BIT(7) + +#define RK805_BUCK1_2_ILMAX_MASK (3 << 6) +#define RK805_BUCK3_4_ILMAX_MASK (3 << 3) +#define RK805_RTC_PERIOD_INT_MASK (1 << 6) +#define RK805_RTC_ALARM_INT_MASK (1 << 5) +#define RK805_INT_ALARM_EN (1 << 3) +#define RK805_INT_TIMER_EN (1 << 2) + /* RK808 IRQ Definitions */ #define RK808_IRQ_VOUT_LO 0 #define RK808_IRQ_VB_LO 1 @@ -298,7 +389,14 @@ enum rk818_reg { #define VOUT_LO_INT BIT(0) #define CLK32KOUT2_EN BIT(0) +#define TEMP115C 0x0c +#define TEMP_HOTDIE_MSK 0x0c +#define SLP_SD_MSK (0x3 << 2) +#define SHUTDOWN_FUN (0x2 << 2) +#define SLEEP_FUN (0x1 << 2) #define RK8XX_ID_MSK 0xfff0 +#define FPWM_MODE BIT(7) + enum { BUCK_ILMIN_50MA, BUCK_ILMIN_100MA, @@ -322,6 +420,28 @@ enum { }; enum { + RK805_BUCK1_2_ILMAX_2500MA, + RK805_BUCK1_2_ILMAX_3000MA, + RK805_BUCK1_2_ILMAX_3500MA, + RK805_BUCK1_2_ILMAX_4000MA, +}; + +enum { + RK805_BUCK3_ILMAX_1500MA, + RK805_BUCK3_ILMAX_2000MA, + RK805_BUCK3_ILMAX_2500MA, + RK805_BUCK3_ILMAX_3000MA, +}; + +enum { + RK805_BUCK4_ILMAX_2000MA, + RK805_BUCK4_ILMAX_2500MA, + RK805_BUCK4_ILMAX_3000MA, + RK805_BUCK4_ILMAX_3500MA, +}; + +enum { + RK805_ID = 0x8050, RK808_ID = 0x0000, RK818_ID = 0x8181, }; -- cgit v1.1 From 67dfabe3a01be6b0cc4c0056aa546f0279ed6279 Mon Sep 17 00:00:00 2001 From: Sebastian Reichel Date: Mon, 21 Aug 2017 16:54:01 +0200 Subject: mfd: da9052: Add register details for TSI Add register details an channels definition for using the TSI registers in the hwmon driver. Signed-off-by: Sebastian Reichel Signed-off-by: Lee Jones --- include/linux/mfd/da9052/da9052.h | 6 ++++++ include/linux/mfd/da9052/reg.h | 11 ++++++++++- 2 files changed, 16 insertions(+), 1 deletion(-) (limited to 'include/linux/mfd') diff --git a/include/linux/mfd/da9052/da9052.h b/include/linux/mfd/da9052/da9052.h index ce9230a..ae5b663 100644 --- a/include/linux/mfd/da9052/da9052.h +++ b/include/linux/mfd/da9052/da9052.h @@ -45,6 +45,12 @@ #define DA9052_ADC_TJUNC 8 #define DA9052_ADC_VBBAT 9 +/* TSI channel has its own 4 channel mux */ +#define DA9052_ADC_TSI_XP 70 +#define DA9052_ADC_TSI_XN 71 +#define DA9052_ADC_TSI_YP 72 +#define DA9052_ADC_TSI_YN 73 + #define DA9052_IRQ_DCIN 0 #define DA9052_IRQ_VBUS 1 #define DA9052_IRQ_DCINREM 2 diff --git a/include/linux/mfd/da9052/reg.h b/include/linux/mfd/da9052/reg.h index 5010f97..76780ea 100644 --- a/include/linux/mfd/da9052/reg.h +++ b/include/linux/mfd/da9052/reg.h @@ -690,7 +690,10 @@ /* TSI CONTROL REGISTER B BITS */ #define DA9052_TSICONTB_ADCREF 0X80 #define DA9052_TSICONTB_TSIMAN 0X40 -#define DA9052_TSICONTB_TSIMUX 0X30 +#define DA9052_TSICONTB_TSIMUX_XP 0X00 +#define DA9052_TSICONTB_TSIMUX_YP 0X10 +#define DA9052_TSICONTB_TSIMUX_XN 0X20 +#define DA9052_TSICONTB_TSIMUX_YN 0X30 #define DA9052_TSICONTB_TSISEL3 0X08 #define DA9052_TSICONTB_TSISEL2 0X04 #define DA9052_TSICONTB_TSISEL1 0X02 @@ -705,8 +708,14 @@ /* TSI CO-ORDINATE LSB RESULT REGISTER BITS */ #define DA9052_TSILSB_PENDOWN 0X40 #define DA9052_TSILSB_TSIZL 0X30 +#define DA9052_TSILSB_TSIZL_SHIFT 4 +#define DA9052_TSILSB_TSIZL_BITS 2 #define DA9052_TSILSB_TSIYL 0X0C +#define DA9052_TSILSB_TSIYL_SHIFT 2 +#define DA9052_TSILSB_TSIYL_BITS 2 #define DA9052_TSILSB_TSIXL 0X03 +#define DA9052_TSILSB_TSIXL_SHIFT 0 +#define DA9052_TSILSB_TSIXL_BITS 2 /* TSI Z MEASUREMENT MSB RESULT REGISTER BIT */ #define DA9052_TSIZMSB_TSIZM 0XFF -- cgit v1.1 From a205425658dead19bb1b8ac00584aed98e60dde2 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Mon, 14 Aug 2017 18:34:24 +0200 Subject: mfd: twl: Move header file out of I2C realm include/linux/i2c is not for client devices. Move the header file to a more appropriate location. Signed-off-by: Wolfram Sang Acked-by: Greg Kroah-Hartman Acked-by: Alexandre Belloni Acked-by: Mark Brown Acked-by: Sebastian Reichel Acked-by: Jonathan Cameron Acked-by: Dmitry Torokhov Acked-by: Kishon Vijay Abraham I Acked-by: Bartlomiej Zolnierkiewicz Acked-by: Thierry Reding Acked-by: Tony Lindgren Acked-by: Daniel Thompson Acked-by: Linus Walleij Acked-by: Guenter Roeck Signed-off-by: Lee Jones --- include/linux/mfd/twl.h | 876 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 876 insertions(+) create mode 100644 include/linux/mfd/twl.h (limited to 'include/linux/mfd') diff --git a/include/linux/mfd/twl.h b/include/linux/mfd/twl.h new file mode 100644 index 0000000..9ad7828 --- /dev/null +++ b/include/linux/mfd/twl.h @@ -0,0 +1,876 @@ +/* + * twl4030.h - header for TWL4030 PM and audio CODEC device + * + * Copyright (C) 2005-2006 Texas Instruments, Inc. + * + * Based on tlv320aic23.c: + * Copyright (c) by Kai Svahn + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#ifndef __TWL_H_ +#define __TWL_H_ + +#include +#include + +/* + * Using the twl4030 core we address registers using a pair + * { module id, relative register offset } + * which that core then maps to the relevant + * { i2c slave, absolute register address } + * + * The module IDs are meaningful only to the twl4030 core code, + * which uses them as array indices to look up the first register + * address each module uses within a given i2c slave. + */ + +/* Module IDs for similar functionalities found in twl4030/twl6030 */ +enum twl_module_ids { + TWL_MODULE_USB, + TWL_MODULE_PIH, + TWL_MODULE_MAIN_CHARGE, + TWL_MODULE_PM_MASTER, + TWL_MODULE_PM_RECEIVER, + + TWL_MODULE_RTC, + TWL_MODULE_PWM, + TWL_MODULE_LED, + TWL_MODULE_SECURED_REG, + + TWL_MODULE_LAST, +}; + +/* Modules only available in twl4030 series */ +enum twl4030_module_ids { + TWL4030_MODULE_AUDIO_VOICE = TWL_MODULE_LAST, + TWL4030_MODULE_GPIO, + TWL4030_MODULE_INTBR, + TWL4030_MODULE_TEST, + TWL4030_MODULE_KEYPAD, + + TWL4030_MODULE_MADC, + TWL4030_MODULE_INTERRUPTS, + TWL4030_MODULE_PRECHARGE, + TWL4030_MODULE_BACKUP, + TWL4030_MODULE_INT, + + TWL5031_MODULE_ACCESSORY, + TWL5031_MODULE_INTERRUPTS, + + TWL4030_MODULE_LAST, +}; + +/* Modules only available in twl6030 series */ +enum twl6030_module_ids { + TWL6030_MODULE_ID0 = TWL_MODULE_LAST, + TWL6030_MODULE_ID1, + TWL6030_MODULE_ID2, + TWL6030_MODULE_GPADC, + TWL6030_MODULE_GASGAUGE, + + TWL6030_MODULE_LAST, +}; + +/* Until the clients has been converted to use TWL_MODULE_LED */ +#define TWL4030_MODULE_LED TWL_MODULE_LED + +#define GPIO_INTR_OFFSET 0 +#define KEYPAD_INTR_OFFSET 1 +#define BCI_INTR_OFFSET 2 +#define MADC_INTR_OFFSET 3 +#define USB_INTR_OFFSET 4 +#define CHARGERFAULT_INTR_OFFSET 5 +#define BCI_PRES_INTR_OFFSET 9 +#define USB_PRES_INTR_OFFSET 10 +#define RTC_INTR_OFFSET 11 + +/* + * Offset from TWL6030_IRQ_BASE / pdata->irq_base + */ +#define PWR_INTR_OFFSET 0 +#define HOTDIE_INTR_OFFSET 12 +#define SMPSLDO_INTR_OFFSET 13 +#define BATDETECT_INTR_OFFSET 14 +#define SIMDETECT_INTR_OFFSET 15 +#define MMCDETECT_INTR_OFFSET 16 +#define GASGAUGE_INTR_OFFSET 17 +#define USBOTG_INTR_OFFSET 4 +#define CHARGER_INTR_OFFSET 2 +#define RSV_INTR_OFFSET 0 + +/* INT register offsets */ +#define REG_INT_STS_A 0x00 +#define REG_INT_STS_B 0x01 +#define REG_INT_STS_C 0x02 + +#define REG_INT_MSK_LINE_A 0x03 +#define REG_INT_MSK_LINE_B 0x04 +#define REG_INT_MSK_LINE_C 0x05 + +#define REG_INT_MSK_STS_A 0x06 +#define REG_INT_MSK_STS_B 0x07 +#define REG_INT_MSK_STS_C 0x08 + +/* MASK INT REG GROUP A */ +#define TWL6030_PWR_INT_MASK 0x07 +#define TWL6030_RTC_INT_MASK 0x18 +#define TWL6030_HOTDIE_INT_MASK 0x20 +#define TWL6030_SMPSLDOA_INT_MASK 0xC0 + +/* MASK INT REG GROUP B */ +#define TWL6030_SMPSLDOB_INT_MASK 0x01 +#define TWL6030_BATDETECT_INT_MASK 0x02 +#define TWL6030_SIMDETECT_INT_MASK 0x04 +#define TWL6030_MMCDETECT_INT_MASK 0x08 +#define TWL6030_GPADC_INT_MASK 0x60 +#define TWL6030_GASGAUGE_INT_MASK 0x80 + +/* MASK INT REG GROUP C */ +#define TWL6030_USBOTG_INT_MASK 0x0F +#define TWL6030_CHARGER_CTRL_INT_MASK 0x10 +#define TWL6030_CHARGER_FAULT_INT_MASK 0x60 + +#define TWL6030_MMCCTRL 0xEE +#define VMMC_AUTO_OFF (0x1 << 3) +#define SW_FC (0x1 << 2) +#define STS_MMC 0x1 + +#define TWL6030_CFG_INPUT_PUPD3 0xF2 +#define MMC_PU (0x1 << 3) +#define MMC_PD (0x1 << 2) + +#define TWL_SIL_TYPE(rev) ((rev) & 0x00FFFFFF) +#define TWL_SIL_REV(rev) ((rev) >> 24) +#define TWL_SIL_5030 0x09002F +#define TWL5030_REV_1_0 0x00 +#define TWL5030_REV_1_1 0x10 +#define TWL5030_REV_1_2 0x30 + +#define TWL4030_CLASS_ID 0x4030 +#define TWL6030_CLASS_ID 0x6030 +unsigned int twl_rev(void); +#define GET_TWL_REV (twl_rev()) +#define TWL_CLASS_IS(class, id) \ +static inline int twl_class_is_ ##class(void) \ +{ \ + return ((id) == (GET_TWL_REV)) ? 1 : 0; \ +} + +TWL_CLASS_IS(4030, TWL4030_CLASS_ID) +TWL_CLASS_IS(6030, TWL6030_CLASS_ID) + +/* Set the regcache bypass for the regmap associated with the nodule */ +int twl_set_regcache_bypass(u8 mod_no, bool enable); + +/* + * Read and write several 8-bit registers at once. + */ +int twl_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); +int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); + +/* + * Read and write single 8-bit registers + */ +static inline int twl_i2c_write_u8(u8 mod_no, u8 val, u8 reg) { + return twl_i2c_write(mod_no, &val, reg, 1); +} + +static inline int twl_i2c_read_u8(u8 mod_no, u8 *val, u8 reg) { + return twl_i2c_read(mod_no, val, reg, 1); +} + +static inline int twl_i2c_write_u16(u8 mod_no, u16 val, u8 reg) { + val = cpu_to_le16(val); + return twl_i2c_write(mod_no, (u8*) &val, reg, 2); +} + +static inline int twl_i2c_read_u16(u8 mod_no, u16 *val, u8 reg) { + int ret; + ret = twl_i2c_read(mod_no, (u8*) val, reg, 2); + *val = le16_to_cpu(*val); + return ret; +} + +int twl_get_type(void); +int twl_get_version(void); +int twl_get_hfclk_rate(void); + +int twl6030_interrupt_unmask(u8 bit_mask, u8 offset); +int twl6030_interrupt_mask(u8 bit_mask, u8 offset); + +/* Card detect Configuration for MMC1 Controller on OMAP4 */ +#ifdef CONFIG_TWL4030_CORE +int twl6030_mmc_card_detect_config(void); +#else +static inline int twl6030_mmc_card_detect_config(void) +{ + pr_debug("twl6030_mmc_card_detect_config not supported\n"); + return 0; +} +#endif + +/* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */ +#ifdef CONFIG_TWL4030_CORE +int twl6030_mmc_card_detect(struct device *dev, int slot); +#else +static inline int twl6030_mmc_card_detect(struct device *dev, int slot) +{ + pr_debug("Call back twl6030_mmc_card_detect not supported\n"); + return -EIO; +} +#endif +/*----------------------------------------------------------------------*/ + +/* + * NOTE: at up to 1024 registers, this is a big chip. + * + * Avoid putting register declarations in this file, instead of into + * a driver-private file, unless some of the registers in a block + * need to be shared with other drivers. One example is blocks that + * have Secondary IRQ Handler (SIH) registers. + */ + +#define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0) +#define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1) +#define TWL4030_SIH_CTRL_COR_MASK BIT(2) + +/*----------------------------------------------------------------------*/ + +/* + * GPIO Block Register offsets (use TWL4030_MODULE_GPIO) + */ + +#define REG_GPIODATAIN1 0x0 +#define REG_GPIODATAIN2 0x1 +#define REG_GPIODATAIN3 0x2 +#define REG_GPIODATADIR1 0x3 +#define REG_GPIODATADIR2 0x4 +#define REG_GPIODATADIR3 0x5 +#define REG_GPIODATAOUT1 0x6 +#define REG_GPIODATAOUT2 0x7 +#define REG_GPIODATAOUT3 0x8 +#define REG_CLEARGPIODATAOUT1 0x9 +#define REG_CLEARGPIODATAOUT2 0xA +#define REG_CLEARGPIODATAOUT3 0xB +#define REG_SETGPIODATAOUT1 0xC +#define REG_SETGPIODATAOUT2 0xD +#define REG_SETGPIODATAOUT3 0xE +#define REG_GPIO_DEBEN1 0xF +#define REG_GPIO_DEBEN2 0x10 +#define REG_GPIO_DEBEN3 0x11 +#define REG_GPIO_CTRL 0x12 +#define REG_GPIOPUPDCTR1 0x13 +#define REG_GPIOPUPDCTR2 0x14 +#define REG_GPIOPUPDCTR3 0x15 +#define REG_GPIOPUPDCTR4 0x16 +#define REG_GPIOPUPDCTR5 0x17 +#define REG_GPIO_ISR1A 0x19 +#define REG_GPIO_ISR2A 0x1A +#define REG_GPIO_ISR3A 0x1B +#define REG_GPIO_IMR1A 0x1C +#define REG_GPIO_IMR2A 0x1D +#define REG_GPIO_IMR3A 0x1E +#define REG_GPIO_ISR1B 0x1F +#define REG_GPIO_ISR2B 0x20 +#define REG_GPIO_ISR3B 0x21 +#define REG_GPIO_IMR1B 0x22 +#define REG_GPIO_IMR2B 0x23 +#define REG_GPIO_IMR3B 0x24 +#define REG_GPIO_EDR1 0x28 +#define REG_GPIO_EDR2 0x29 +#define REG_GPIO_EDR3 0x2A +#define REG_GPIO_EDR4 0x2B +#define REG_GPIO_EDR5 0x2C +#define REG_GPIO_SIH_CTRL 0x2D + +/* Up to 18 signals are available as GPIOs, when their + * pins are not assigned to another use (such as ULPI/USB). + */ +#define TWL4030_GPIO_MAX 18 + +/*----------------------------------------------------------------------*/ + +/*Interface Bit Register (INTBR) offsets + *(Use TWL_4030_MODULE_INTBR) + */ + +#define REG_IDCODE_7_0 0x00 +#define REG_IDCODE_15_8 0x01 +#define REG_IDCODE_16_23 0x02 +#define REG_IDCODE_31_24 0x03 +#define REG_GPPUPDCTR1 0x0F +#define REG_UNLOCK_TEST_REG 0x12 + +/*I2C1 and I2C4(SR) SDA/SCL pull-up control bits */ + +#define I2C_SCL_CTRL_PU BIT(0) +#define I2C_SDA_CTRL_PU BIT(2) +#define SR_I2C_SCL_CTRL_PU BIT(4) +#define SR_I2C_SDA_CTRL_PU BIT(6) + +#define TWL_EEPROM_R_UNLOCK 0x49 + +/*----------------------------------------------------------------------*/ + +/* + * Keypad register offsets (use TWL4030_MODULE_KEYPAD) + * ... SIH/interrupt only + */ + +#define TWL4030_KEYPAD_KEYP_ISR1 0x11 +#define TWL4030_KEYPAD_KEYP_IMR1 0x12 +#define TWL4030_KEYPAD_KEYP_ISR2 0x13 +#define TWL4030_KEYPAD_KEYP_IMR2 0x14 +#define TWL4030_KEYPAD_KEYP_SIR 0x15 /* test register */ +#define TWL4030_KEYPAD_KEYP_EDR 0x16 +#define TWL4030_KEYPAD_KEYP_SIH_CTRL 0x17 + +/*----------------------------------------------------------------------*/ + +/* + * Multichannel ADC register offsets (use TWL4030_MODULE_MADC) + * ... SIH/interrupt only + */ + +#define TWL4030_MADC_ISR1 0x61 +#define TWL4030_MADC_IMR1 0x62 +#define TWL4030_MADC_ISR2 0x63 +#define TWL4030_MADC_IMR2 0x64 +#define TWL4030_MADC_SIR 0x65 /* test register */ +#define TWL4030_MADC_EDR 0x66 +#define TWL4030_MADC_SIH_CTRL 0x67 + +/*----------------------------------------------------------------------*/ + +/* + * Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS) + */ + +#define TWL4030_INTERRUPTS_BCIISR1A 0x0 +#define TWL4030_INTERRUPTS_BCIISR2A 0x1 +#define TWL4030_INTERRUPTS_BCIIMR1A 0x2 +#define TWL4030_INTERRUPTS_BCIIMR2A 0x3 +#define TWL4030_INTERRUPTS_BCIISR1B 0x4 +#define TWL4030_INTERRUPTS_BCIISR2B 0x5 +#define TWL4030_INTERRUPTS_BCIIMR1B 0x6 +#define TWL4030_INTERRUPTS_BCIIMR2B 0x7 +#define TWL4030_INTERRUPTS_BCISIR1 0x8 /* test register */ +#define TWL4030_INTERRUPTS_BCISIR2 0x9 /* test register */ +#define TWL4030_INTERRUPTS_BCIEDR1 0xa +#define TWL4030_INTERRUPTS_BCIEDR2 0xb +#define TWL4030_INTERRUPTS_BCIEDR3 0xc +#define TWL4030_INTERRUPTS_BCISIHCTRL 0xd + +/*----------------------------------------------------------------------*/ + +/* + * Power Interrupt block register offsets (use TWL4030_MODULE_INT) + */ + +#define TWL4030_INT_PWR_ISR1 0x0 +#define TWL4030_INT_PWR_IMR1 0x1 +#define TWL4030_INT_PWR_ISR2 0x2 +#define TWL4030_INT_PWR_IMR2 0x3 +#define TWL4030_INT_PWR_SIR 0x4 /* test register */ +#define TWL4030_INT_PWR_EDR1 0x5 +#define TWL4030_INT_PWR_EDR2 0x6 +#define TWL4030_INT_PWR_SIH_CTRL 0x7 + +/*----------------------------------------------------------------------*/ + +/* + * Accessory Interrupts + */ +#define TWL5031_ACIIMR_LSB 0x05 +#define TWL5031_ACIIMR_MSB 0x06 +#define TWL5031_ACIIDR_LSB 0x07 +#define TWL5031_ACIIDR_MSB 0x08 +#define TWL5031_ACCISR1 0x0F +#define TWL5031_ACCIMR1 0x10 +#define TWL5031_ACCISR2 0x11 +#define TWL5031_ACCIMR2 0x12 +#define TWL5031_ACCSIR 0x13 +#define TWL5031_ACCEDR1 0x14 +#define TWL5031_ACCSIHCTRL 0x15 + +/*----------------------------------------------------------------------*/ + +/* + * Battery Charger Controller + */ + +#define TWL5031_INTERRUPTS_BCIISR1 0x0 +#define TWL5031_INTERRUPTS_BCIIMR1 0x1 +#define TWL5031_INTERRUPTS_BCIISR2 0x2 +#define TWL5031_INTERRUPTS_BCIIMR2 0x3 +#define TWL5031_INTERRUPTS_BCISIR 0x4 +#define TWL5031_INTERRUPTS_BCIEDR1 0x5 +#define TWL5031_INTERRUPTS_BCIEDR2 0x6 +#define TWL5031_INTERRUPTS_BCISIHCTRL 0x7 + +/*----------------------------------------------------------------------*/ + +/* + * PM Master module register offsets (use TWL4030_MODULE_PM_MASTER) + */ + +#define TWL4030_PM_MASTER_CFG_P1_TRANSITION 0x00 +#define TWL4030_PM_MASTER_CFG_P2_TRANSITION 0x01 +#define TWL4030_PM_MASTER_CFG_P3_TRANSITION 0x02 +#define TWL4030_PM_MASTER_CFG_P123_TRANSITION 0x03 +#define TWL4030_PM_MASTER_STS_BOOT 0x04 +#define TWL4030_PM_MASTER_CFG_BOOT 0x05 +#define TWL4030_PM_MASTER_SHUNDAN 0x06 +#define TWL4030_PM_MASTER_BOOT_BCI 0x07 +#define TWL4030_PM_MASTER_CFG_PWRANA1 0x08 +#define TWL4030_PM_MASTER_CFG_PWRANA2 0x09 +#define TWL4030_PM_MASTER_BACKUP_MISC_STS 0x0b +#define TWL4030_PM_MASTER_BACKUP_MISC_CFG 0x0c +#define TWL4030_PM_MASTER_BACKUP_MISC_TST 0x0d +#define TWL4030_PM_MASTER_PROTECT_KEY 0x0e +#define TWL4030_PM_MASTER_STS_HW_CONDITIONS 0x0f +#define TWL4030_PM_MASTER_P1_SW_EVENTS 0x10 +#define TWL4030_PM_MASTER_P2_SW_EVENTS 0x11 +#define TWL4030_PM_MASTER_P3_SW_EVENTS 0x12 +#define TWL4030_PM_MASTER_STS_P123_STATE 0x13 +#define TWL4030_PM_MASTER_PB_CFG 0x14 +#define TWL4030_PM_MASTER_PB_WORD_MSB 0x15 +#define TWL4030_PM_MASTER_PB_WORD_LSB 0x16 +#define TWL4030_PM_MASTER_SEQ_ADD_W2P 0x1c +#define TWL4030_PM_MASTER_SEQ_ADD_P2A 0x1d +#define TWL4030_PM_MASTER_SEQ_ADD_A2W 0x1e +#define TWL4030_PM_MASTER_SEQ_ADD_A2S 0x1f +#define TWL4030_PM_MASTER_SEQ_ADD_S2A12 0x20 +#define TWL4030_PM_MASTER_SEQ_ADD_S2A3 0x21 +#define TWL4030_PM_MASTER_SEQ_ADD_WARM 0x22 +#define TWL4030_PM_MASTER_MEMORY_ADDRESS 0x23 +#define TWL4030_PM_MASTER_MEMORY_DATA 0x24 + +#define TWL4030_PM_MASTER_KEY_CFG1 0xc0 +#define TWL4030_PM_MASTER_KEY_CFG2 0x0c + +#define TWL4030_PM_MASTER_KEY_TST1 0xe0 +#define TWL4030_PM_MASTER_KEY_TST2 0x0e + +#define TWL4030_PM_MASTER_GLOBAL_TST 0xb6 + +/*----------------------------------------------------------------------*/ + +/* Power bus message definitions */ + +/* The TWL4030/5030 splits its power-management resources (the various + * regulators, clock and reset lines) into 3 processor groups - P1, P2 and + * P3. These groups can then be configured to transition between sleep, wait-on + * and active states by sending messages to the power bus. See Section 5.4.2 + * Power Resources of TWL4030 TRM + */ + +/* Processor groups */ +#define DEV_GRP_NULL 0x0 +#define DEV_GRP_P1 0x1 /* P1: all OMAP devices */ +#define DEV_GRP_P2 0x2 /* P2: all Modem devices */ +#define DEV_GRP_P3 0x4 /* P3: all peripheral devices */ + +/* Resource groups */ +#define RES_GRP_RES 0x0 /* Reserved */ +#define RES_GRP_PP 0x1 /* Power providers */ +#define RES_GRP_RC 0x2 /* Reset and control */ +#define RES_GRP_PP_RC 0x3 +#define RES_GRP_PR 0x4 /* Power references */ +#define RES_GRP_PP_PR 0x5 +#define RES_GRP_RC_PR 0x6 +#define RES_GRP_ALL 0x7 /* All resource groups */ + +#define RES_TYPE2_R0 0x0 +#define RES_TYPE2_R1 0x1 +#define RES_TYPE2_R2 0x2 + +#define RES_TYPE_R0 0x0 +#define RES_TYPE_ALL 0x7 + +/* Resource states */ +#define RES_STATE_WRST 0xF +#define RES_STATE_ACTIVE 0xE +#define RES_STATE_SLEEP 0x8 +#define RES_STATE_OFF 0x0 + +/* Power resources */ + +/* Power providers */ +#define RES_VAUX1 1 +#define RES_VAUX2 2 +#define RES_VAUX3 3 +#define RES_VAUX4 4 +#define RES_VMMC1 5 +#define RES_VMMC2 6 +#define RES_VPLL1 7 +#define RES_VPLL2 8 +#define RES_VSIM 9 +#define RES_VDAC 10 +#define RES_VINTANA1 11 +#define RES_VINTANA2 12 +#define RES_VINTDIG 13 +#define RES_VIO 14 +#define RES_VDD1 15 +#define RES_VDD2 16 +#define RES_VUSB_1V5 17 +#define RES_VUSB_1V8 18 +#define RES_VUSB_3V1 19 +#define RES_VUSBCP 20 +#define RES_REGEN 21 +/* Reset and control */ +#define RES_NRES_PWRON 22 +#define RES_CLKEN 23 +#define RES_SYSEN 24 +#define RES_HFCLKOUT 25 +#define RES_32KCLKOUT 26 +#define RES_RESET 27 +/* Power Reference */ +#define RES_MAIN_REF 28 + +#define TOTAL_RESOURCES 28 +/* + * Power Bus Message Format ... these can be sent individually by Linux, + * but are usually part of downloaded scripts that are run when various + * power events are triggered. + * + * Broadcast Message (16 Bits): + * DEV_GRP[15:13] MT[12] RES_GRP[11:9] RES_TYPE2[8:7] RES_TYPE[6:4] + * RES_STATE[3:0] + * + * Singular Message (16 Bits): + * DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0] + */ + +#define MSG_BROADCAST(devgrp, grp, type, type2, state) \ + ( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \ + | (type) << 4 | (state)) + +#define MSG_SINGULAR(devgrp, id, state) \ + ((devgrp) << 13 | 0 << 12 | (id) << 4 | (state)) + +#define MSG_BROADCAST_ALL(devgrp, state) \ + ((devgrp) << 5 | (state)) + +#define MSG_BROADCAST_REF MSG_BROADCAST_ALL +#define MSG_BROADCAST_PROV MSG_BROADCAST_ALL +#define MSG_BROADCAST__CLK_RST MSG_BROADCAST_ALL +/*----------------------------------------------------------------------*/ + +struct twl4030_clock_init_data { + bool ck32k_lowpwr_enable; +}; + +struct twl4030_bci_platform_data { + int *battery_tmp_tbl; + unsigned int tblsize; + int bb_uvolt; /* voltage to charge backup battery */ + int bb_uamp; /* current for backup battery charging */ +}; + +/* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */ +struct twl4030_gpio_platform_data { + /* package the two LED signals as output-only GPIOs? */ + bool use_leds; + + /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */ + u8 mmc_cd; + + /* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */ + u32 debounce; + + /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup + * should be enabled. Else, if that bit is set in "pulldowns", + * that pulldown is enabled. Don't waste power by letting any + * digital inputs float... + */ + u32 pullups; + u32 pulldowns; + + int (*setup)(struct device *dev, + unsigned gpio, unsigned ngpio); + int (*teardown)(struct device *dev, + unsigned gpio, unsigned ngpio); +}; + +struct twl4030_madc_platform_data { + int irq_line; +}; + +/* Boards have unique mappings of {row, col} --> keycode. + * Column and row are 8 bits each, but range only from 0..7. + * a PERSISTENT_KEY is "always on" and never reported. + */ +#define PERSISTENT_KEY(r, c) KEY((r), (c), KEY_RESERVED) + +struct twl4030_keypad_data { + const struct matrix_keymap_data *keymap_data; + unsigned rows; + unsigned cols; + bool rep; +}; + +enum twl4030_usb_mode { + T2_USB_MODE_ULPI = 1, + T2_USB_MODE_CEA2011_3PIN = 2, +}; + +struct twl4030_usb_data { + enum twl4030_usb_mode usb_mode; + unsigned long features; + + int (*phy_init)(struct device *dev); + int (*phy_exit)(struct device *dev); + /* Power on/off the PHY */ + int (*phy_power)(struct device *dev, int iD, int on); + /* enable/disable phy clocks */ + int (*phy_set_clock)(struct device *dev, int on); + /* suspend/resume of phy */ + int (*phy_suspend)(struct device *dev, int suspend); +}; + +struct twl4030_ins { + u16 pmb_message; + u8 delay; +}; + +struct twl4030_script { + struct twl4030_ins *script; + unsigned size; + u8 flags; +#define TWL4030_WRST_SCRIPT (1<<0) +#define TWL4030_WAKEUP12_SCRIPT (1<<1) +#define TWL4030_WAKEUP3_SCRIPT (1<<2) +#define TWL4030_SLEEP_SCRIPT (1<<3) +}; + +struct twl4030_resconfig { + u8 resource; + u8 devgroup; /* Processor group that Power resource belongs to */ + u8 type; /* Power resource addressed, 6 / broadcast message */ + u8 type2; /* Power resource addressed, 3 / broadcast message */ + u8 remap_off; /* off state remapping */ + u8 remap_sleep; /* sleep state remapping */ +}; + +struct twl4030_power_data { + struct twl4030_script **scripts; + unsigned num; + struct twl4030_resconfig *resource_config; + struct twl4030_resconfig *board_config; +#define TWL4030_RESCONFIG_UNDEF ((u8)-1) + bool use_poweroff; /* Board is wired for TWL poweroff */ + bool ac_charger_quirk; /* Disable AC charger on board */ +}; + +extern int twl4030_remove_script(u8 flags); +extern void twl4030_power_off(void); + +struct twl4030_codec_data { + unsigned int digimic_delay; /* in ms */ + unsigned int ramp_delay_value; + unsigned int offset_cncl_path; + unsigned int hs_extmute:1; + int hs_extmute_gpio; +}; + +struct twl4030_vibra_data { + unsigned int coexist; +}; + +struct twl4030_audio_data { + unsigned int audio_mclk; + struct twl4030_codec_data *codec; + struct twl4030_vibra_data *vibra; + + /* twl6040 */ + int audpwron_gpio; /* audio power-on gpio */ + int naudint_irq; /* audio interrupt */ + unsigned int irq_base; +}; + +struct twl4030_platform_data { + struct twl4030_clock_init_data *clock; + struct twl4030_bci_platform_data *bci; + struct twl4030_gpio_platform_data *gpio; + struct twl4030_madc_platform_data *madc; + struct twl4030_keypad_data *keypad; + struct twl4030_usb_data *usb; + struct twl4030_power_data *power; + struct twl4030_audio_data *audio; + + /* Common LDO regulators for TWL4030/TWL6030 */ + struct regulator_init_data *vdac; + struct regulator_init_data *vaux1; + struct regulator_init_data *vaux2; + struct regulator_init_data *vaux3; + struct regulator_init_data *vdd1; + struct regulator_init_data *vdd2; + struct regulator_init_data *vdd3; + /* TWL4030 LDO regulators */ + struct regulator_init_data *vpll1; + struct regulator_init_data *vpll2; + struct regulator_init_data *vmmc1; + struct regulator_init_data *vmmc2; + struct regulator_init_data *vsim; + struct regulator_init_data *vaux4; + struct regulator_init_data *vio; + struct regulator_init_data *vintana1; + struct regulator_init_data *vintana2; + struct regulator_init_data *vintdig; + /* TWL6030 LDO regulators */ + struct regulator_init_data *vmmc; + struct regulator_init_data *vpp; + struct regulator_init_data *vusim; + struct regulator_init_data *vana; + struct regulator_init_data *vcxio; + struct regulator_init_data *vusb; + struct regulator_init_data *clk32kg; + struct regulator_init_data *v1v8; + struct regulator_init_data *v2v1; + /* TWL6032 LDO regulators */ + struct regulator_init_data *ldo1; + struct regulator_init_data *ldo2; + struct regulator_init_data *ldo3; + struct regulator_init_data *ldo4; + struct regulator_init_data *ldo5; + struct regulator_init_data *ldo6; + struct regulator_init_data *ldo7; + struct regulator_init_data *ldoln; + struct regulator_init_data *ldousb; + /* TWL6032 DCDC regulators */ + struct regulator_init_data *smps3; + struct regulator_init_data *smps4; + struct regulator_init_data *vio6025; +}; + +struct twl_regulator_driver_data { + int (*set_voltage)(void *data, int target_uV); + int (*get_voltage)(void *data); + void *data; + unsigned long features; +}; +/* chip-specific feature flags, for twl_regulator_driver_data.features */ +#define TWL4030_VAUX2 BIT(0) /* pre-5030 voltage ranges */ +#define TPS_SUBSET BIT(1) /* tps659[23]0 have fewer LDOs */ +#define TWL5031 BIT(2) /* twl5031 has different registers */ +#define TWL6030_CLASS BIT(3) /* TWL6030 class */ +#define TWL6032_SUBCLASS BIT(4) /* TWL6032 has changed registers */ +#define TWL4030_ALLOW_UNSUPPORTED BIT(5) /* Some voltages are possible + * but not officially supported. + * This flag is necessary to + * enable them. + */ + +/*----------------------------------------------------------------------*/ + +int twl4030_sih_setup(struct device *dev, int module, int irq_base); + +/* Offsets to Power Registers */ +#define TWL4030_VDAC_DEV_GRP 0x3B +#define TWL4030_VDAC_DEDICATED 0x3E +#define TWL4030_VAUX1_DEV_GRP 0x17 +#define TWL4030_VAUX1_DEDICATED 0x1A +#define TWL4030_VAUX2_DEV_GRP 0x1B +#define TWL4030_VAUX2_DEDICATED 0x1E +#define TWL4030_VAUX3_DEV_GRP 0x1F +#define TWL4030_VAUX3_DEDICATED 0x22 + +static inline int twl4030charger_usb_en(int enable) { return 0; } + +/*----------------------------------------------------------------------*/ + +/* Linux-specific regulator identifiers ... for now, we only support + * the LDOs, and leave the three buck converters alone. VDD1 and VDD2 + * need to tie into hardware based voltage scaling (cpufreq etc), while + * VIO is generally fixed. + */ + +/* TWL4030 SMPS/LDO's */ +/* EXTERNAL dc-to-dc buck converters */ +#define TWL4030_REG_VDD1 0 +#define TWL4030_REG_VDD2 1 +#define TWL4030_REG_VIO 2 + +/* EXTERNAL LDOs */ +#define TWL4030_REG_VDAC 3 +#define TWL4030_REG_VPLL1 4 +#define TWL4030_REG_VPLL2 5 /* not on all chips */ +#define TWL4030_REG_VMMC1 6 +#define TWL4030_REG_VMMC2 7 /* not on all chips */ +#define TWL4030_REG_VSIM 8 /* not on all chips */ +#define TWL4030_REG_VAUX1 9 /* not on all chips */ +#define TWL4030_REG_VAUX2_4030 10 /* (twl4030-specific) */ +#define TWL4030_REG_VAUX2 11 /* (twl5030 and newer) */ +#define TWL4030_REG_VAUX3 12 /* not on all chips */ +#define TWL4030_REG_VAUX4 13 /* not on all chips */ + +/* INTERNAL LDOs */ +#define TWL4030_REG_VINTANA1 14 +#define TWL4030_REG_VINTANA2 15 +#define TWL4030_REG_VINTDIG 16 +#define TWL4030_REG_VUSB1V5 17 +#define TWL4030_REG_VUSB1V8 18 +#define TWL4030_REG_VUSB3V1 19 + +/* TWL6030 SMPS/LDO's */ +/* EXTERNAL dc-to-dc buck convertor controllable via SR */ +#define TWL6030_REG_VDD1 30 +#define TWL6030_REG_VDD2 31 +#define TWL6030_REG_VDD3 32 + +/* Non SR compliant dc-to-dc buck convertors */ +#define TWL6030_REG_VMEM 33 +#define TWL6030_REG_V2V1 34 +#define TWL6030_REG_V1V29 35 +#define TWL6030_REG_V1V8 36 + +/* EXTERNAL LDOs */ +#define TWL6030_REG_VAUX1_6030 37 +#define TWL6030_REG_VAUX2_6030 38 +#define TWL6030_REG_VAUX3_6030 39 +#define TWL6030_REG_VMMC 40 +#define TWL6030_REG_VPP 41 +#define TWL6030_REG_VUSIM 42 +#define TWL6030_REG_VANA 43 +#define TWL6030_REG_VCXIO 44 +#define TWL6030_REG_VDAC 45 +#define TWL6030_REG_VUSB 46 + +/* INTERNAL LDOs */ +#define TWL6030_REG_VRTC 47 +#define TWL6030_REG_CLK32KG 48 + +/* LDOs on 6025 have different names */ +#define TWL6032_REG_LDO2 49 +#define TWL6032_REG_LDO4 50 +#define TWL6032_REG_LDO3 51 +#define TWL6032_REG_LDO5 52 +#define TWL6032_REG_LDO1 53 +#define TWL6032_REG_LDO7 54 +#define TWL6032_REG_LDO6 55 +#define TWL6032_REG_LDOLN 56 +#define TWL6032_REG_LDOUSB 57 + +/* 6025 DCDC supplies */ +#define TWL6032_REG_SMPS3 58 +#define TWL6032_REG_SMPS4 59 +#define TWL6032_REG_VIO 60 + + +#endif /* End of __TWL4030_H */ -- cgit v1.1 From e8924005b4e7964313536547d4b73406330be26d Mon Sep 17 00:00:00 2001 From: Fabrice Gasnier Date: Mon, 28 Aug 2017 12:04:07 +0200 Subject: mfd: Add STM32 LPTimer driver STM32 Low-Power Timer hardware block can be used for: - PWM generation - IIO trigger (in sync with PWM) - IIO quadrature encoder counter PWM and IIO timer configuration are mixed in the same registers so we need a multi fonction driver to be able to share those registers. Signed-off-by: Fabrice Gasnier Signed-off-by: Lee Jones --- include/linux/mfd/stm32-lptimer.h | 62 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 62 insertions(+) create mode 100644 include/linux/mfd/stm32-lptimer.h (limited to 'include/linux/mfd') diff --git a/include/linux/mfd/stm32-lptimer.h b/include/linux/mfd/stm32-lptimer.h new file mode 100644 index 0000000..77c7cf4 --- /dev/null +++ b/include/linux/mfd/stm32-lptimer.h @@ -0,0 +1,62 @@ +/* + * STM32 Low-Power Timer parent driver. + * + * Copyright (C) STMicroelectronics 2017 + * + * Author: Fabrice Gasnier + * + * Inspired by Benjamin Gaignard's stm32-timers driver + * + * License terms: GNU General Public License (GPL), version 2 + */ + +#ifndef _LINUX_STM32_LPTIMER_H_ +#define _LINUX_STM32_LPTIMER_H_ + +#include +#include + +#define STM32_LPTIM_ISR 0x00 /* Interrupt and Status Reg */ +#define STM32_LPTIM_ICR 0x04 /* Interrupt Clear Reg */ +#define STM32_LPTIM_IER 0x08 /* Interrupt Enable Reg */ +#define STM32_LPTIM_CFGR 0x0C /* Configuration Reg */ +#define STM32_LPTIM_CR 0x10 /* Control Reg */ +#define STM32_LPTIM_CMP 0x14 /* Compare Reg */ +#define STM32_LPTIM_ARR 0x18 /* Autoreload Reg */ +#define STM32_LPTIM_CNT 0x1C /* Counter Reg */ + +/* STM32_LPTIM_ISR - bit fields */ +#define STM32_LPTIM_CMPOK_ARROK GENMASK(4, 3) +#define STM32_LPTIM_ARROK BIT(4) +#define STM32_LPTIM_CMPOK BIT(3) + +/* STM32_LPTIM_ICR - bit fields */ +#define STM32_LPTIM_CMPOKCF_ARROKCF GENMASK(4, 3) + +/* STM32_LPTIM_CR - bit fields */ +#define STM32_LPTIM_CNTSTRT BIT(2) +#define STM32_LPTIM_ENABLE BIT(0) + +/* STM32_LPTIM_CFGR - bit fields */ +#define STM32_LPTIM_ENC BIT(24) +#define STM32_LPTIM_COUNTMODE BIT(23) +#define STM32_LPTIM_WAVPOL BIT(21) +#define STM32_LPTIM_PRESC GENMASK(11, 9) +#define STM32_LPTIM_CKPOL GENMASK(2, 1) + +/* STM32_LPTIM_ARR */ +#define STM32_LPTIM_MAX_ARR 0xFFFF + +/** + * struct stm32_lptimer - STM32 Low-Power Timer data assigned by parent device + * @clk: clock reference for this instance + * @regmap: register map reference for this instance + * @has_encoder: indicates this Low-Power Timer supports encoder mode + */ +struct stm32_lptimer { + struct clk *clk; + struct regmap *regmap; + bool has_encoder; +}; + +#endif -- cgit v1.1