From 72f30b6f2f5f68dd426e9fe83817b882c2d04e50 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Tue, 27 Sep 2005 10:19:39 -0700
Subject: [PATCH] USB: ehci.patch (earlier irq disable)

This tweaks the EHCI reboot notifier to also halt the EHCI controller, and
makes that halt code force IRQs off.  Both should always have been done.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/ehci-hcd.c |    8 ++++++++
 1 file changed, 8 insertions(+)
---
 drivers/usb/host/ehci-hcd.c | 8 ++++++++
 1 file changed, 8 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index f5eb9e7..b3eb026 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -182,6 +182,9 @@ static int ehci_halt (struct ehci_hcd *ehci)
 {
 	u32	temp = readl (&ehci->regs->status);
 
+	/* disable any irqs left enabled by previous code */
+	writel (0, &ehci->regs->intr_enable);
+
 	if ((temp & STS_HALT) != 0)
 		return 0;
 
@@ -335,12 +338,17 @@ static int bios_handoff (struct ehci_hcd *ehci, int where, u32 cap)
 
 #endif
 
+/* Reboot notifiers kick in for silicon on any bus (not just pci, etc).
+ * This forcibly disables dma and IRQs, helping kexec and other cases
+ * where the next system software may expect clean state.
+ */
 static int
 ehci_reboot (struct notifier_block *self, unsigned long code, void *null)
 {
 	struct ehci_hcd		*ehci;
 
 	ehci = container_of (self, struct ehci_hcd, reboot_notifier);
+	(void) ehci_halt (ehci);
 
 	/* make BIOS/etc use companion controller during reboot */
 	writel (0, &ehci->regs->configured_flag);
-- 
cgit v1.1


From c9c7746dd333c12f482af2f1e63ea7eafc7cd529 Mon Sep 17 00:00:00 2001
From: Rui Santos <rsantos@grupopie.com>
Date: Fri, 23 Sep 2005 20:06:50 +0100
Subject: [PATCH] USB: ftdi: Artemis and ATIK based USB astronomical CCD
 cameras

This patch enables direct kernel support for the Artemis
and ATIK astronomical based USB CCD cameras.
Since all communications with this camera are done via an
FTDI 245BM chip, it was only needed to specify the
ProductID and VendorID of all three devices.
In what tests are concerned, data was transfered from and
to the FTDI at the chips Top speed (360KB/s).

Signed-off-by: Rui Santos <rsantos@grupopie.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/serial/ftdi_sio.c |    3 +++
 drivers/usb/serial/ftdi_sio.h |   13 +++++++++++++
 2 files changed, 16 insertions(+)
---
 drivers/usb/serial/ftdi_sio.c |  3 +++
 drivers/usb/serial/ftdi_sio.h | 13 +++++++++++++
 2 files changed, 16 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 5a8631c..8c12a0a 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -471,6 +471,9 @@ static struct usb_device_id id_table_combined [] = {
 	{ USB_DEVICE(FTDI_VID, FTDI_MHAM_Y6_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_MHAM_Y8_PID) },
 	{ USB_DEVICE(EVOLUTION_VID, EVOLUTION_ER1_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_ARTEMIS_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_ATIK_ATK16_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_ATIK_ATK16HR_PID) },
 	{ },					/* Optional parameter entry */
 	{ }					/* Terminating entry */
 };
diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h
index 2c35d74..7c65d46 100644
--- a/drivers/usb/serial/ftdi_sio.h
+++ b/drivers/usb/serial/ftdi_sio.h
@@ -199,6 +199,19 @@
 #define FTDI_PIEGROUP_PID	0xF208	/* Product Id */
 
 /*
+ * Definitions for Artemis astronomical USB based cameras
+ * Check it at http://www.artemisccd.co.uk/
+ */
+#define FTDI_ARTEMIS_PID	0xDF28	/* All Artemis Cameras */
+
+/*
+ * Definitions for ATIK Instruments astronomical USB based cameras
+ * Check it at http://www.atik-instruments.com/
+ */
+#define FTDI_ATIK_ATK16_PID	0xDF30	/* ATIK ATK-16 Camera */
+#define FTDI_ATIK_ATK16HR_PID	0xDF31	/* ATIK ATK-16HR Camera */
+
+/*
  * Protego product ids
  */
 #define PROTEGO_SPECIAL_1	0xFC70	/* special/unknown device */
-- 
cgit v1.1


From 8da608caa07d5c9745ec86bf7c25ad423352f9a4 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: disable tasklet if rtl8150 device is removed while
 active.

This fixes a oops seen in the wild.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/net/rtl8150.c | 1 +
 1 file changed, 1 insertion(+)

(limited to 'drivers')

diff --git a/drivers/usb/net/rtl8150.c b/drivers/usb/net/rtl8150.c
index c3d4e35..787dd35 100644
--- a/drivers/usb/net/rtl8150.c
+++ b/drivers/usb/net/rtl8150.c
@@ -909,6 +909,7 @@ static void rtl8150_disconnect(struct usb_interface *intf)
 	usb_set_intfdata(intf, NULL);
 	if (dev) {
 		set_bit(RTL8150_UNPLUG, &dev->flags);
+		tasklet_disable(&dev->tl);
 		unregister_netdev(dev->netdev);
 		unlink_all_urbs(dev);
 		free_all_urbs(dev);
-- 
cgit v1.1


From 094f1649577dfc7f2c7407a8380e05a506b31f7f Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: add endpoint information to sysfs

This patch adds endpoint information for both devices and interfaces to
sysfs.  Previously it was only possible to get the endpoint information
from usbfs, and never possible to get any information on endpoint 0.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/sysfs.c |  195 ++++++++++++++++++++++++++++++++++++++++++++++-
 include/linux/usb.h      |    4
 2 files changed, 197 insertions(+), 2 deletions(-)
---
 drivers/usb/core/sysfs.c | 195 ++++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 193 insertions(+), 2 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/sysfs.c b/drivers/usb/core/sysfs.c
index 00297f1..eae413b 100644
--- a/drivers/usb/core/sysfs.c
+++ b/drivers/usb/core/sysfs.c
@@ -22,6 +22,174 @@
 
 #include "usb.h"
 
+/* endpoint stuff */
+struct endpoint_attribute {
+	struct device_attribute dev_attr;
+	struct usb_endpoint_descriptor *endpoint;
+	struct usb_device *udev;
+};
+#define to_endpoint_attr(_dev_attr) \
+	container_of(_dev_attr, struct endpoint_attribute, dev_attr)
+
+#define usb_ep_attr(field, format_string)					\
+static ssize_t show_ep_##field(struct device *dev, struct device_attribute *attr,	\
+			    char *buf)						\
+{										\
+	struct endpoint_attribute *endpoint_attr = to_endpoint_attr(attr);	\
+										\
+	return sprintf(buf, format_string, endpoint_attr->endpoint->field);	\
+}
+usb_ep_attr(bLength, "%02x\n")
+usb_ep_attr(bDescriptorType, "%02x\n")
+usb_ep_attr(bEndpointAddress, "%02x\n")
+usb_ep_attr(bmAttributes, "%02x\n")
+usb_ep_attr(bInterval, "%02x\n")
+
+static ssize_t show_ep_wMaxPacketSize(struct device *dev,
+				      struct device_attribute *attr, char *buf)
+{
+	struct endpoint_attribute *endpoint_attr = to_endpoint_attr(attr);
+
+	return sprintf(buf, "%04x\n",
+		      le16_to_cpu(endpoint_attr->endpoint->wMaxPacketSize) & 0x07ff);
+}
+
+static ssize_t show_ep_type(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct endpoint_attribute *endpoint_attr = to_endpoint_attr(attr);
+	char *type = "unknown";
+
+	switch (endpoint_attr->endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) {
+	case USB_ENDPOINT_XFER_CONTROL:
+		type = "Control";
+		break;
+	case USB_ENDPOINT_XFER_ISOC:
+		type = "Isoc";
+		break;
+	case USB_ENDPOINT_XFER_BULK:
+		type = "Bulk";
+		break;
+	case USB_ENDPOINT_XFER_INT:
+		type = "Interrupt";
+		break;
+	}
+	return sprintf(buf, "%s\n", type);
+}
+
+static ssize_t show_ep_interval(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct endpoint_attribute *endpoint_attr = to_endpoint_attr(attr);
+	struct usb_device *udev = endpoint_attr->udev;
+	struct usb_endpoint_descriptor *endpoint = endpoint_attr->endpoint;
+	char unit;
+	unsigned interval = 0;
+	unsigned in;
+
+	in = (endpoint->bEndpointAddress & USB_DIR_IN);
+
+	switch (endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) {
+	case USB_ENDPOINT_XFER_CONTROL:
+		if (udev->speed == USB_SPEED_HIGH) 	/* uframes per NAK */
+			interval = endpoint->bInterval;
+		break;
+	case USB_ENDPOINT_XFER_ISOC:
+		interval = 1 << (endpoint->bInterval - 1);
+		break;
+	case USB_ENDPOINT_XFER_BULK:
+		if (udev->speed == USB_SPEED_HIGH && !in)	/* uframes per NAK */
+			interval = endpoint->bInterval;
+		break;
+	case USB_ENDPOINT_XFER_INT:
+		if (udev->speed == USB_SPEED_HIGH) {
+			interval = 1 << (endpoint->bInterval - 1);
+		} else
+			interval = endpoint->bInterval;
+		break;
+	}
+	interval *= (udev->speed == USB_SPEED_HIGH) ? 125 : 1000;
+	if (interval % 1000)
+		unit = 'u';
+	else {
+		unit = 'm';
+		interval /= 1000;
+	}
+
+	return sprintf(buf, "%d%cs\n", interval, unit);
+}
+
+static ssize_t show_ep_direction(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct endpoint_attribute *endpoint_attr = to_endpoint_attr(attr);
+	char *direction;
+
+	if ((endpoint_attr->endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
+	    USB_ENDPOINT_XFER_CONTROL)
+		direction = "both";
+	else if (endpoint_attr->endpoint->bEndpointAddress & USB_DIR_IN)
+		direction = "in";
+	else
+		direction = "out";
+	return sprintf(buf, "%s\n", direction);
+}
+
+static struct endpoint_attribute *create_ep_attr(struct usb_endpoint_descriptor *endpoint,
+						 struct usb_device *udev, char *name,
+		ssize_t (*show)(struct device *dev, struct device_attribute *attr, char *buf))
+{
+	struct endpoint_attribute *ep_attr;
+
+	ep_attr = kzalloc(sizeof(*ep_attr), GFP_KERNEL);
+	if (ep_attr) {
+		ep_attr->endpoint = endpoint;
+		ep_attr->udev = udev;
+		ep_attr->dev_attr.attr.name = name;
+		ep_attr->dev_attr.attr.mode = 0444;
+		ep_attr->dev_attr.attr.owner = THIS_MODULE;
+		ep_attr->dev_attr.show = show;
+	}
+	return ep_attr;
+}
+
+static void usb_create_ep_files(struct kobject *kobj, struct usb_host_endpoint *endpoint, struct usb_device *udev)
+{
+	struct usb_endpoint_descriptor *ep;
+
+	ep = &endpoint->desc;
+
+	endpoint->attrs = kzalloc(sizeof(struct attribute *) * 10, GFP_KERNEL);
+	endpoint->attrs[0] = &(create_ep_attr(ep, udev, "direction", show_ep_direction)->dev_attr.attr);
+	endpoint->attrs[1] = &(create_ep_attr(ep, udev, "type", show_ep_type)->dev_attr.attr);
+	endpoint->attrs[2] = &(create_ep_attr(ep, udev, "bLength", show_ep_bLength)->dev_attr.attr);
+	endpoint->attrs[3] = &(create_ep_attr(ep, udev, "bDescriptorType", show_ep_bDescriptorType)->dev_attr.attr);
+	endpoint->attrs[4] = &(create_ep_attr(ep, udev, "bEndpointAddress", show_ep_bEndpointAddress)->dev_attr.attr);
+	endpoint->attrs[5] = &(create_ep_attr(ep, udev, "bmAttributes", show_ep_bmAttributes)->dev_attr.attr);
+	endpoint->attrs[6] = &(create_ep_attr(ep, udev, "wMaxPacketSize", show_ep_wMaxPacketSize)->dev_attr.attr);
+	endpoint->attrs[7] = &(create_ep_attr(ep, udev, "bInterval", show_ep_bInterval)->dev_attr.attr);
+	endpoint->attrs[8] = &(create_ep_attr(ep, udev, "interval", show_ep_interval)->dev_attr.attr);
+	endpoint->attrs[9] = NULL;
+	endpoint->num_attrs = 9;
+
+	endpoint->attr_group = kzalloc(sizeof(*endpoint->attr_group), GFP_KERNEL);
+	endpoint->attr_name = kzalloc(10, GFP_KERNEL);
+	sprintf(endpoint->attr_name, "ep_%02x", endpoint->desc.bEndpointAddress);
+
+	endpoint->attr_group->attrs = endpoint->attrs;
+	endpoint->attr_group->name = endpoint->attr_name;
+	sysfs_create_group(kobj, endpoint->attr_group);
+}
+
+static void usb_remove_ep_files(struct kobject *kobj, struct usb_host_endpoint *endpoint)
+{
+	int i;
+
+	sysfs_remove_group(kobj, endpoint->attr_group);
+	kfree(endpoint->attr_group);
+	kfree(endpoint->attr_name);
+	for (i = 0; i < endpoint->num_attrs; ++i)
+		kfree(endpoint->attrs[i]);
+	kfree(endpoint->attrs);
+}
+
 /* Active configuration fields */
 #define usb_actconfig_show(field, multiplier, format_string)		\
 static ssize_t  show_##field (struct device *dev, struct device_attribute *attr, char *buf)		\
@@ -236,12 +404,14 @@ void usb_create_sysfs_dev_files (struct usb_device *udev)
 	if (udev->serial)
 		device_create_file (dev, &dev_attr_serial);
 	device_create_file (dev, &dev_attr_configuration);
+	usb_create_ep_files(&dev->kobj, &udev->ep0, udev);
 }
 
 void usb_remove_sysfs_dev_files (struct usb_device *udev)
 {
 	struct device *dev = &udev->dev;
 
+	usb_remove_ep_files(&dev->kobj, &udev->ep0);
 	sysfs_remove_group(&dev->kobj, &dev_attr_grp);
 
 	if (udev->descriptor.iManufacturer)
@@ -333,20 +503,41 @@ static struct attribute_group intf_attr_grp = {
 	.attrs = intf_attrs,
 };
 
+static void usb_create_intf_ep_files(struct usb_interface *intf)
+{
+	struct usb_host_interface *iface_desc;
+	int i;
+
+	iface_desc = intf->cur_altsetting;
+	for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i)
+		usb_create_ep_files(&intf->dev.kobj, &iface_desc->endpoint[i],
+				    interface_to_usbdev(intf));
+}
+
+static void usb_remove_intf_ep_files(struct usb_interface *intf)
+{
+	struct usb_host_interface *iface_desc;
+	int i;
+
+	iface_desc = intf->cur_altsetting;
+	for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i)
+		usb_remove_ep_files(&intf->dev.kobj, &iface_desc->endpoint[i]);
+}
+
 void usb_create_sysfs_intf_files (struct usb_interface *intf)
 {
 	sysfs_create_group(&intf->dev.kobj, &intf_attr_grp);
 
 	if (intf->cur_altsetting->string)
 		device_create_file(&intf->dev, &dev_attr_interface);
-		
+	usb_create_intf_ep_files(intf);
 }
 
 void usb_remove_sysfs_intf_files (struct usb_interface *intf)
 {
+	usb_remove_intf_ep_files(intf);
 	sysfs_remove_group(&intf->dev.kobj, &intf_attr_grp);
 
 	if (intf->cur_altsetting->string)
 		device_remove_file(&intf->dev, &dev_attr_interface);
-
 }
-- 
cgit v1.1


From d6e5bcf4a7ebbe258124a931f1449338340a99b5 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] devfs: Remove the mode field from usb_class_driver as it's no
 longer needed

Also fixes all drivers that set this field, and removes some other devfs
specfic USB logic.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/class/usblp.c           |    3 +--
 drivers/usb/core/file.c             |   19 ++++---------------
 drivers/usb/image/mdc800.c          |    3 +--
 drivers/usb/input/aiptek.c          |    2 +-
 drivers/usb/input/hiddev.c          |    3 +--
 drivers/usb/media/dabusb.c          |    3 +--
 drivers/usb/misc/auerswald.c        |    3 +--
 drivers/usb/misc/idmouse.c          |    5 ++---
 drivers/usb/misc/legousbtower.c     |    5 ++---
 drivers/usb/misc/rio500.c           |    3 +--
 drivers/usb/misc/sisusbvga/sisusb.c |    5 -----
 drivers/usb/misc/usblcd.c           |    9 ++++-----
 drivers/usb/usb-skeleton.c          |    3 +--
 include/linux/usb.h                 |    7 ++-----
 14 files changed, 22 insertions(+), 51 deletions(-)
---
 drivers/usb/class/usblp.c           |  3 +--
 drivers/usb/core/file.c             | 19 ++++---------------
 drivers/usb/image/mdc800.c          |  3 +--
 drivers/usb/input/aiptek.c          |  2 +-
 drivers/usb/input/hiddev.c          |  3 +--
 drivers/usb/media/dabusb.c          |  3 +--
 drivers/usb/misc/auerswald.c        |  3 +--
 drivers/usb/misc/idmouse.c          |  5 ++---
 drivers/usb/misc/legousbtower.c     |  5 ++---
 drivers/usb/misc/rio500.c           |  3 +--
 drivers/usb/misc/sisusbvga/sisusb.c |  5 -----
 drivers/usb/misc/usblcd.c           |  9 ++++-----
 drivers/usb/usb-skeleton.c          |  3 +--
 13 files changed, 20 insertions(+), 46 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/class/usblp.c b/drivers/usb/class/usblp.c
index e195709..357e753 100644
--- a/drivers/usb/class/usblp.c
+++ b/drivers/usb/class/usblp.c
@@ -844,9 +844,8 @@ static struct file_operations usblp_fops = {
 };
 
 static struct usb_class_driver usblp_class = {
-	.name =		"usb/lp%d",
+	.name =		"lp%d",
 	.fops =		&usblp_fops,
-	.mode =		S_IFCHR | S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP,
 	.minor_base =	USBLP_MINOR_BASE,
 };
 
diff --git a/drivers/usb/core/file.c b/drivers/usb/core/file.c
index 78cb4be..e695308 100644
--- a/drivers/usb/core/file.c
+++ b/drivers/usb/core/file.c
@@ -17,7 +17,6 @@
 
 #include <linux/config.h>
 #include <linux/module.h>
-#include <linux/devfs_fs_kernel.h>
 #include <linux/spinlock.h>
 #include <linux/errno.h>
 
@@ -88,8 +87,6 @@ int usb_major_init(void)
 		goto out;
 	}
 
-	devfs_mk_dir("usb");
-
 out:
 	return error;
 }
@@ -97,7 +94,6 @@ out:
 void usb_major_cleanup(void)
 {
 	class_destroy(usb_class);
-	devfs_remove("usb");
 	unregister_chrdev(USB_MAJOR, "usb");
 }
 
@@ -112,8 +108,7 @@ void usb_major_cleanup(void)
  * enabled, the minor number will be based on the next available free minor,
  * starting at the class_driver->minor_base.
  *
- * This function also creates the devfs file for the usb device, if devfs
- * is enabled, and creates a usb class device in the sysfs tree.
+ * This function also creates a usb class device in the sysfs tree.
  *
  * usb_deregister_dev() must be called when the driver is done with
  * the minor numbers given out by this function.
@@ -162,11 +157,8 @@ int usb_register_dev(struct usb_interface *intf,
 
 	intf->minor = minor;
 
-	/* handle the devfs registration */
-	snprintf(name, BUS_ID_SIZE, class_driver->name, minor - minor_base);
-	devfs_mk_cdev(MKDEV(USB_MAJOR, minor), class_driver->mode, name);
-
 	/* create a usb class device for this usb interface */
+	snprintf(name, BUS_ID_SIZE, class_driver->name, minor - minor_base);
 	temp = strrchr(name, '/');
 	if (temp && (temp[1] != 0x00))
 		++temp;
@@ -179,7 +171,6 @@ int usb_register_dev(struct usb_interface *intf,
 		spin_lock (&minor_lock);
 		usb_minors[intf->minor] = NULL;
 		spin_unlock (&minor_lock);
-		devfs_remove (name);
 		retval = PTR_ERR(intf->class_dev);
 	}
 exit:
@@ -197,9 +188,8 @@ EXPORT_SYMBOL(usb_register_dev);
  * call to usb_register_dev() (usually when the device is disconnected
  * from the system.)
  *
- * This function also cleans up the devfs file for the usb device, if devfs
- * is enabled, and removes the usb class device from the sysfs tree.
- * 
+ * This function also removes the usb class device from the sysfs tree.
+ *
  * This should be called by all drivers that use the USB major number.
  */
 void usb_deregister_dev(struct usb_interface *intf,
@@ -222,7 +212,6 @@ void usb_deregister_dev(struct usb_interface *intf,
 	spin_unlock (&minor_lock);
 
 	snprintf(name, BUS_ID_SIZE, class_driver->name, intf->minor - minor_base);
-	devfs_remove (name);
 	class_device_destroy(usb_class, MKDEV(USB_MAJOR, intf->minor));
 	intf->class_dev = NULL;
 	intf->minor = -1;
diff --git a/drivers/usb/image/mdc800.c b/drivers/usb/image/mdc800.c
index a330a4b..e4ec133 100644
--- a/drivers/usb/image/mdc800.c
+++ b/drivers/usb/image/mdc800.c
@@ -425,9 +425,8 @@ static void mdc800_usb_download_notify (struct urb *urb, struct pt_regs *res)
 static struct usb_driver mdc800_usb_driver;
 static struct file_operations mdc800_device_ops;
 static struct usb_class_driver mdc800_class = {
-	.name =		"usb/mdc800%d",
+	.name =		"mdc800%d",
 	.fops =		&mdc800_device_ops,
-	.mode =		S_IFCHR | S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP,
 	.minor_base =	MDC800_DEVICE_MINOR_BASE,
 };
 
diff --git a/drivers/usb/input/aiptek.c b/drivers/usb/input/aiptek.c
index 1c52053..1c3b472 100644
--- a/drivers/usb/input/aiptek.c
+++ b/drivers/usb/input/aiptek.c
@@ -2154,7 +2154,7 @@ aiptek_probe(struct usb_interface *intf, const struct usb_device_id *id)
 	 * input_handles associated with this input device.
 	 * What identifies an evdev input_handler is that it begins
 	 * with 'event', continues with a digit, and that in turn
-	 * is mapped to /{devfs}/input/eventN.
+	 * is mapped to input/eventN.
 	 */
 	list_for_each_safe(node, next, &inputdev->h_list) {
 		inputhandle = to_handle(node);
diff --git a/drivers/usb/input/hiddev.c b/drivers/usb/input/hiddev.c
index d324278..440377c 100644
--- a/drivers/usb/input/hiddev.c
+++ b/drivers/usb/input/hiddev.c
@@ -732,9 +732,8 @@ static struct file_operations hiddev_fops = {
 };
 
 static struct usb_class_driver hiddev_class = {
-	.name =		"usb/hid/hiddev%d",
+	.name =		"hiddev%d",
 	.fops =		&hiddev_fops,
-	.mode =		S_IFCHR | S_IRUGO | S_IWUSR,
 	.minor_base =	HIDDEV_MINOR_BASE,
 };
 
diff --git a/drivers/usb/media/dabusb.c b/drivers/usb/media/dabusb.c
index 6ca2fae..27b23c5 100644
--- a/drivers/usb/media/dabusb.c
+++ b/drivers/usb/media/dabusb.c
@@ -707,9 +707,8 @@ static struct file_operations dabusb_fops =
 };
 
 static struct usb_class_driver dabusb_class = {
-	.name =		"usb/dabusb%d",
+	.name =		"dabusb%d",
 	.fops =		&dabusb_fops,
-	.mode =		S_IFCHR | S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP,
 	.minor_base =	DABUSB_MINOR,
 };
 
diff --git a/drivers/usb/misc/auerswald.c b/drivers/usb/misc/auerswald.c
index ae4681f..5f33f7c 100644
--- a/drivers/usb/misc/auerswald.c
+++ b/drivers/usb/misc/auerswald.c
@@ -1873,9 +1873,8 @@ static struct file_operations auerswald_fops =
 };
 
 static struct usb_class_driver auerswald_class = {
-	.name =		"usb/auer%d",
+	.name =		"auer%d",
 	.fops =		&auerswald_fops,
-	.mode =		S_IFCHR | S_IRUGO | S_IWUGO,
 	.minor_base =	AUER_MINOR_BASE,
 };
 
diff --git a/drivers/usb/misc/idmouse.c b/drivers/usb/misc/idmouse.c
index 733acc2..3944a55 100644
--- a/drivers/usb/misc/idmouse.c
+++ b/drivers/usb/misc/idmouse.c
@@ -105,11 +105,10 @@ static struct file_operations idmouse_fops = {
 	.release = idmouse_release,
 };
 
-/* class driver information for devfs */
+/* class driver information */
 static struct usb_class_driver idmouse_class = {
-	.name = "usb/idmouse%d",
+	.name = "idmouse%d",
 	.fops = &idmouse_fops,
-	.mode = S_IFCHR | S_IRUSR | S_IRGRP | S_IROTH, /* filemode (char, 444) */
 	.minor_base = USB_IDMOUSE_MINOR_BASE,
 };
 
diff --git a/drivers/usb/misc/legousbtower.c b/drivers/usb/misc/legousbtower.c
index 7d06105..2703e20 100644
--- a/drivers/usb/misc/legousbtower.c
+++ b/drivers/usb/misc/legousbtower.c
@@ -271,12 +271,11 @@ static struct file_operations tower_fops = {
 
 /*
  * usb class driver info in order to get a minor number from the usb core,
- * and to have the device registered with devfs and the driver core
+ * and to have the device registered with the driver core
  */
 static struct usb_class_driver tower_class = {
-	.name =		"usb/legousbtower%d",
+	.name =		"legousbtower%d",
 	.fops =		&tower_fops,
-	.mode =		S_IFCHR | S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP | S_IROTH,
 	.minor_base =	LEGO_USB_TOWER_MINOR_BASE,
 };
 
diff --git a/drivers/usb/misc/rio500.c b/drivers/usb/misc/rio500.c
index 26f77e2..7d02d8e 100644
--- a/drivers/usb/misc/rio500.c
+++ b/drivers/usb/misc/rio500.c
@@ -443,9 +443,8 @@ file_operations usb_rio_fops = {
 };
 
 static struct usb_class_driver usb_rio_class = {
-	.name =		"usb/rio500%d",
+	.name =		"rio500%d",
 	.fops =		&usb_rio_fops,
-	.mode =		S_IFCHR | S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP,
 	.minor_base =	RIO_MINOR,
 };
 
diff --git a/drivers/usb/misc/sisusbvga/sisusb.c b/drivers/usb/misc/sisusbvga/sisusb.c
index 39db315..222ae9c 100644
--- a/drivers/usb/misc/sisusbvga/sisusb.c
+++ b/drivers/usb/misc/sisusbvga/sisusb.c
@@ -3239,12 +3239,7 @@ static struct file_operations usb_sisusb_fops = {
 };
 
 static struct usb_class_driver usb_sisusb_class = {
-#if LINUX_VERSION_CODE <= KERNEL_VERSION(2,6,13)
-	.name =		"usb/sisusbvga%d",
-	.mode =		S_IFCHR | S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP,
-#else
 	.name =		"sisusbvga%d",
-#endif
 	.fops =		&usb_sisusb_fops,
 	.minor_base =	SISUSB_MINOR
 };
diff --git a/drivers/usb/misc/usblcd.c b/drivers/usb/misc/usblcd.c
index 096ab30..85f3725 100644
--- a/drivers/usb/misc/usblcd.c
+++ b/drivers/usb/misc/usblcd.c
@@ -251,13 +251,12 @@ static struct file_operations lcd_fops = {
 };
 
 /*
- *  * usb class driver info in order to get a minor number from the usb core,
- *   * and to have the device registered with devfs and the driver core
- *    */
+ * usb class driver info in order to get a minor number from the usb core,
+ * and to have the device registered with the driver core
+ */
 static struct usb_class_driver lcd_class = {
-        .name =         "usb/lcd%d",
+        .name =         "lcd%d",
         .fops =         &lcd_fops,
-        .mode =         S_IFCHR | S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP | S_IROTH,
         .minor_base =   USBLCD_MINOR,
 };
 
diff --git a/drivers/usb/usb-skeleton.c b/drivers/usb/usb-skeleton.c
index 353f24d..6c3a53f 100644
--- a/drivers/usb/usb-skeleton.c
+++ b/drivers/usb/usb-skeleton.c
@@ -223,9 +223,8 @@ static struct file_operations skel_fops = {
  * and to have the device registered with devfs and the driver core
  */
 static struct usb_class_driver skel_class = {
-	.name =		"usb/skel%d",
+	.name =		"skel%d",
 	.fops =		&skel_fops,
-	.mode =		S_IFCHR | S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP | S_IROTH,
 	.minor_base =	USB_SKEL_MINOR_BASE,
 };
 
-- 
cgit v1.1


From e639dd3f4edd4847d160899b19e95ee1a06a6dcb Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: add more snooping hooks in devio.c

Now we can log the urbs travelling through usbfs

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/devio.c | 55 +++++++++++++++++++++++++++++++++++++++++++-----
 1 file changed, 50 insertions(+), 5 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index befe0c7..6c15dab 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -279,6 +279,28 @@ static inline struct async *async_getpending(struct dev_state *ps, void __user *
         return NULL;
 }
 
+static void snoop_urb(struct urb *urb, void __user *userurb)
+{
+	int j;
+	unsigned char *data = urb->transfer_buffer;
+
+	if (!usbfs_snoop)
+		return;
+
+	if (urb->pipe & USB_DIR_IN)
+		dev_info(&urb->dev->dev, "direction=IN\n");
+	else
+		dev_info(&urb->dev->dev, "direction=OUT\n");
+	dev_info(&urb->dev->dev, "userurb=%p\n", userurb);
+	dev_info(&urb->dev->dev, "transfer_buffer_length=%d\n",
+		 urb->transfer_buffer_length);
+	dev_info(&urb->dev->dev, "actual_length=%d\n", urb->actual_length);
+	dev_info(&urb->dev->dev, "data: ");
+	for (j = 0; j < urb->transfer_buffer_length; ++j)
+		printk ("%02x ", data[j]);
+	printk("\n");
+}
+
 static void async_completed(struct urb *urb, struct pt_regs *regs)
 {
         struct async *as = (struct async *)urb->context;
@@ -296,7 +318,9 @@ static void async_completed(struct urb *urb, struct pt_regs *regs)
 		kill_proc_info_as_uid(as->signr, &sinfo, as->pid, as->uid, 
 				      as->euid);
 	}
-        wake_up(&ps->wait);
+	snoop(&urb->dev->dev, "urb complete\n");
+	snoop_urb(urb, as->userurb);
+	wake_up(&ps->wait);
 }
 
 static void destroy_async (struct dev_state *ps, struct list_head *list)
@@ -601,7 +625,7 @@ static int proc_control(struct dev_state *ps, void __user *arg)
 			if (usbfs_snoop) {
 				dev_info(&dev->dev, "control read: data ");
 				for (j = 0; j < i; ++j)
-					printk ("%02x ", (unsigned char)(tbuf)[j]);
+					printk("%02x ", (unsigned char)(tbuf)[j]);
 				printk("\n");
 			}
 			if (copy_to_user(ctrl.data, tbuf, i)) {
@@ -624,7 +648,7 @@ static int proc_control(struct dev_state *ps, void __user *arg)
 		if (usbfs_snoop) {
 			dev_info(&dev->dev, "control write: data: ");
 			for (j = 0; j < ctrl.wLength; ++j)
-				printk ("%02x ", (unsigned char)(tbuf)[j]);
+				printk("%02x ", (unsigned char)(tbuf)[j]);
 			printk("\n");
 		}
 		usb_unlock_device(dev);
@@ -649,7 +673,7 @@ static int proc_bulk(struct dev_state *ps, void __user *arg)
 	unsigned int tmo, len1, pipe;
 	int len2;
 	unsigned char *tbuf;
-	int i, ret;
+	int i, j, ret;
 
 	if (copy_from_user(&bulk, arg, sizeof(bulk)))
 		return -EFAULT;
@@ -674,10 +698,18 @@ static int proc_bulk(struct dev_state *ps, void __user *arg)
 			kfree(tbuf);
 			return -EINVAL;
 		}
+		snoop(&dev->dev, "bulk read: len=0x%02x timeout=%04d\n",
+			bulk.len, bulk.timeout);
 		usb_unlock_device(dev);
 		i = usb_bulk_msg(dev, pipe, tbuf, len1, &len2, tmo);
 		usb_lock_device(dev);
 		if (!i && len2) {
+			if (usbfs_snoop) {
+				dev_info(&dev->dev, "bulk read: data ");
+				for (j = 0; j < len2; ++j)
+					printk("%02x ", (unsigned char)(tbuf)[j]);
+				printk("\n");
+			}
 			if (copy_to_user(bulk.data, tbuf, len2)) {
 				kfree(tbuf);
 				return -EFAULT;
@@ -690,6 +722,14 @@ static int proc_bulk(struct dev_state *ps, void __user *arg)
 				return -EFAULT;
 			}
 		}
+		snoop(&dev->dev, "bulk write: len=0x%02x timeout=%04d\n",
+			bulk.len, bulk.timeout);
+		if (usbfs_snoop) {
+			dev_info(&dev->dev, "bulk write: data: ");
+			for (j = 0; j < len1; ++j)
+				printk("%02x ", (unsigned char)(tbuf)[j]);
+			printk("\n");
+		}
 		usb_unlock_device(dev);
 		i = usb_bulk_msg(dev, pipe, tbuf, len1, &len2, tmo);
 		usb_lock_device(dev);
@@ -835,7 +875,6 @@ static int proc_setconfig(struct dev_state *ps, void __user *arg)
 	return status;
 }
 
-
 static int proc_do_submiturb(struct dev_state *ps, struct usbdevfs_urb *uurb,
 			     struct usbdevfs_iso_packet_desc __user *iso_frame_desc,
 			     void __user *arg)
@@ -896,6 +935,7 @@ static int proc_do_submiturb(struct dev_state *ps, struct usbdevfs_urb *uurb,
 			kfree(dr);
 			return -EFAULT;
 		}
+		snoop(&ps->dev->dev, "control urb\n");
 		break;
 
 	case USBDEVFS_URB_TYPE_BULK:
@@ -910,6 +950,7 @@ static int proc_do_submiturb(struct dev_state *ps, struct usbdevfs_urb *uurb,
 			return -EINVAL;
 		if (!access_ok((uurb->endpoint & USB_DIR_IN) ? VERIFY_WRITE : VERIFY_READ, uurb->buffer, uurb->buffer_length))
 			return -EFAULT;
+		snoop(&ps->dev->dev, "bulk urb\n");
 		break;
 
 	case USBDEVFS_URB_TYPE_ISO:
@@ -939,6 +980,7 @@ static int proc_do_submiturb(struct dev_state *ps, struct usbdevfs_urb *uurb,
 			return -EINVAL;
 		}
 		uurb->buffer_length = totlen;
+		snoop(&ps->dev->dev, "iso urb\n");
 		break;
 
 	case USBDEVFS_URB_TYPE_INTERRUPT:
@@ -954,6 +996,7 @@ static int proc_do_submiturb(struct dev_state *ps, struct usbdevfs_urb *uurb,
 			return -EINVAL;
 		if (!access_ok((uurb->endpoint & USB_DIR_IN) ? VERIFY_WRITE : VERIFY_READ, uurb->buffer, uurb->buffer_length))
 			return -EFAULT;
+		snoop(&ps->dev->dev, "interrupt urb\n");
 		break;
 
 	default:
@@ -1003,6 +1046,8 @@ static int proc_do_submiturb(struct dev_state *ps, struct usbdevfs_urb *uurb,
 			return -EFAULT;
 		}
 	}
+	snoop(&as->urb->dev->dev, "submit urb\n");
+	snoop_urb(as->urb, as->userurb);
         async_newpending(as);
         if ((ret = usb_submit_urb(as->urb, GFP_KERNEL))) {
 		dev_printk(KERN_DEBUG, &ps->dev->dev, "usbfs: usb_submit_urb returned %d\n", ret);
-- 
cgit v1.1


From 38ffdd62b0f466ef9126ac9f060ade5f218b4887 Mon Sep 17 00:00:00 2001
From: Pete Zaitcev <zaitcev@redhat.com>
Date: Sat, 24 Sep 2005 13:10:16 -0700
Subject: [PATCH] ub: suppress gcc warnings for pointer casts

When building on a 64-bit platform, gcc produces a warning
"cast of a pointer to an integer of a different size".
The scatterlist.offset on the LHS is unsigned int, so I used
that originally.

Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/block/ub.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
---
 drivers/block/ub.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

(limited to 'drivers')

diff --git a/drivers/block/ub.c b/drivers/block/ub.c
index ed4d500..bfb23d5 100644
--- a/drivers/block/ub.c
+++ b/drivers/block/ub.c
@@ -1512,7 +1512,7 @@ static void ub_state_sense(struct ub_dev *sc, struct ub_scsi_cmd *cmd)
 	scmd->nsg = 1;
 	sg = &scmd->sgv[0];
 	sg->page = virt_to_page(sc->top_sense);
-	sg->offset = (unsigned int)sc->top_sense & (PAGE_SIZE-1);
+	sg->offset = (unsigned long)sc->top_sense & (PAGE_SIZE-1);
 	sg->length = UB_SENSE_SIZE;
 	scmd->len = UB_SENSE_SIZE;
 	scmd->lun = cmd->lun;
@@ -1891,7 +1891,7 @@ static int ub_sync_read_cap(struct ub_dev *sc, struct ub_lun *lun,
 	cmd->nsg = 1;
 	sg = &cmd->sgv[0];
 	sg->page = virt_to_page(p);
-	sg->offset = (unsigned int)p & (PAGE_SIZE-1);
+	sg->offset = (unsigned long)p & (PAGE_SIZE-1);
 	sg->length = 8;
 	cmd->len = 8;
 	cmd->lun = lun;
-- 
cgit v1.1


From 7586269c0b52970f60bb69fcb86e765fc1d72309 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Fri, 23 Sep 2005 17:14:37 -0700
Subject: [PATCH] USB: move handoff code

This moves the PCI quirk handling for USB host controllers from the
PCI directory to the USB directory.  Follow-on patches will need to:

(a) merge these copies with the originals in the HCD reset methods.
they don't wholly agree, despite doing the very same thing; and

(b) eventually change it so "usb-handoff" is the default, to help
get more robust USB/BIOS/input/... interactions.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/Makefile              |    2
 drivers/pci/quirks.c          |  253 ---------------------------------------
 drivers/usb/Makefile          |    1
 drivers/usb/host/Makefile     |    5
 drivers/usb/host/pci-quirks.c |  272 ++++++++++++++++++++++++++++++++++++++++++
 5 files changed, 280 insertions(+), 253 deletions(-)
---
 drivers/Makefile              |   2 +-
 drivers/pci/quirks.c          | 253 +--------------------------------------
 drivers/usb/Makefile          |   1 +
 drivers/usb/host/Makefile     |   5 +-
 drivers/usb/host/pci-quirks.c | 272 ++++++++++++++++++++++++++++++++++++++++++
 5 files changed, 280 insertions(+), 253 deletions(-)
 create mode 100644 drivers/usb/host/pci-quirks.c

(limited to 'drivers')

diff --git a/drivers/Makefile b/drivers/Makefile
index 1a109a6..65670be 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -5,7 +5,7 @@
 # Rewritten to use lists instead of if-statements.
 #
 
-obj-$(CONFIG_PCI)		+= pci/
+obj-$(CONFIG_PCI)		+= pci/ usb/
 obj-$(CONFIG_PARISC)		+= parisc/
 obj-y				+= video/
 obj-$(CONFIG_ACPI)		+= acpi/
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index ee16059..bbd9c23 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -7,6 +7,9 @@
  *
  *  Copyright (c) 1999 Martin Mares <mj@ucw.cz>
  *
+ *  Init/reset quirks for USB host controllers should be in the
+ *  USB quirks file, where their drivers can access reuse it.
+ *
  *  The bridge optimization stuff has been removed. If you really
  *  have a silly BIOS which is unable to set your host bridge right,
  *  use the PowerTweak utility (see http://powertweak.sourceforge.net).
@@ -645,28 +648,6 @@ static void quirk_via_irq(struct pci_dev *dev)
 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq);
 
 /*
- * PIIX3 USB: We have to disable USB interrupts that are
- * hardwired to PIRQD# and may be shared with an
- * external device.
- *
- * Legacy Support Register (LEGSUP):
- *     bit13:  USB PIRQ Enable (USBPIRQDEN),
- *     bit4:   Trap/SMI On IRQ Enable (USBSMIEN).
- *
- * We mask out all r/wc bits, too.
- */
-static void __devinit quirk_piix3_usb(struct pci_dev *dev)
-{
-	u16 legsup;
-
-	pci_read_config_word(dev, 0xc0, &legsup);
-	legsup &= 0x50ef;
-	pci_write_config_word(dev, 0xc0, legsup);
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82371SB_2,	quirk_piix3_usb );
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82371AB_2,	quirk_piix3_usb );
-
-/*
  * VIA VT82C598 has its device ID settable and many BIOSes
  * set it to the ID of VT82C597 for backward compatibility.
  * We need to switch it off to be able to recognize the real
@@ -1039,234 +1020,6 @@ static void __init quirk_sis_96x_smbus(struct pci_dev *dev)
 	pci_read_config_byte(dev, 0x77, &val);
 }
 
-
-#define UHCI_USBLEGSUP		0xc0		/* legacy support */
-#define UHCI_USBCMD		0		/* command register */
-#define UHCI_USBSTS		2		/* status register */
-#define UHCI_USBINTR		4		/* interrupt register */
-#define UHCI_USBLEGSUP_DEFAULT	0x2000		/* only PIRQ enable set */
-#define UHCI_USBCMD_RUN		(1 << 0)	/* RUN/STOP bit */
-#define UHCI_USBCMD_GRESET	(1 << 2)	/* Global reset */
-#define UHCI_USBCMD_CONFIGURE	(1 << 6)	/* config semaphore */
-#define UHCI_USBSTS_HALTED	(1 << 5)	/* HCHalted bit */
-
-#define OHCI_CONTROL		0x04
-#define OHCI_CMDSTATUS		0x08
-#define OHCI_INTRSTATUS		0x0c
-#define OHCI_INTRENABLE		0x10
-#define OHCI_INTRDISABLE	0x14
-#define OHCI_OCR		(1 << 3)	/* ownership change request */
-#define OHCI_CTRL_IR		(1 << 8)	/* interrupt routing */
-#define OHCI_INTR_OC		(1 << 30)	/* ownership change */
-
-#define EHCI_HCC_PARAMS		0x08		/* extended capabilities */
-#define EHCI_USBCMD		0		/* command register */
-#define EHCI_USBCMD_RUN		(1 << 0)	/* RUN/STOP bit */
-#define EHCI_USBSTS		4		/* status register */
-#define EHCI_USBSTS_HALTED	(1 << 12)	/* HCHalted bit */
-#define EHCI_USBINTR		8		/* interrupt register */
-#define EHCI_USBLEGSUP		0		/* legacy support register */
-#define EHCI_USBLEGSUP_BIOS	(1 << 16)	/* BIOS semaphore */
-#define EHCI_USBLEGSUP_OS	(1 << 24)	/* OS semaphore */
-#define EHCI_USBLEGCTLSTS	4		/* legacy control/status */
-#define EHCI_USBLEGCTLSTS_SOOE	(1 << 13)	/* SMI on ownership change */
-
-int usb_early_handoff __devinitdata = 0;
-static int __init usb_handoff_early(char *str)
-{
-	usb_early_handoff = 1;
-	return 0;
-}
-__setup("usb-handoff", usb_handoff_early);
-
-static void __devinit quirk_usb_handoff_uhci(struct pci_dev *pdev)
-{
-	unsigned long base = 0;
-	int wait_time, delta;
-	u16 val, sts;
-	int i;
-
-	for (i = 0; i < PCI_ROM_RESOURCE; i++)
-		if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
-			base = pci_resource_start(pdev, i);
-			break;
-		}
-
-	if (!base)
-		return;
-
-	/*
-	 * stop controller
-	 */
-	sts = inw(base + UHCI_USBSTS);
-	val = inw(base + UHCI_USBCMD);
-	val &= ~(u16)(UHCI_USBCMD_RUN | UHCI_USBCMD_CONFIGURE);
-	outw(val, base + UHCI_USBCMD);
-
-	/*
-	 * wait while it stops if it was running
-	 */
-	if ((sts & UHCI_USBSTS_HALTED) == 0)
-	{
-		wait_time = 1000;
-		delta = 100;
-
-		do {
-			outw(0x1f, base + UHCI_USBSTS);
-			udelay(delta);
-			wait_time -= delta;
-			val = inw(base + UHCI_USBSTS);
-			if (val & UHCI_USBSTS_HALTED)
-				break;
-		} while (wait_time > 0);
-	}
-
-	/*
-	 * disable interrupts & legacy support
-	 */
-	outw(0, base + UHCI_USBINTR);
-	outw(0x1f, base + UHCI_USBSTS);
-	pci_read_config_word(pdev, UHCI_USBLEGSUP, &val);
-	if (val & 0xbf) 
-		pci_write_config_word(pdev, UHCI_USBLEGSUP, UHCI_USBLEGSUP_DEFAULT);
-		
-}
-
-static void __devinit quirk_usb_handoff_ohci(struct pci_dev *pdev)
-{
-	void __iomem *base;
-	int wait_time;
-
-	base = ioremap_nocache(pci_resource_start(pdev, 0),
-				     pci_resource_len(pdev, 0));
-	if (base == NULL) return;
-
-	if (readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
-		wait_time = 500; /* 0.5 seconds */
-		writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
-		writel(OHCI_OCR, base + OHCI_CMDSTATUS);
-		while (wait_time > 0 && 
-				readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
-			wait_time -= 10;
-			msleep(10);
-		}
-	}
-
-	/*
-	 * disable interrupts
-	 */
-	writel(~(u32)0, base + OHCI_INTRDISABLE);
-	writel(~(u32)0, base + OHCI_INTRSTATUS);
-
-	iounmap(base);
-}
-
-static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev)
-{
-	int wait_time, delta;
-	void __iomem *base, *op_reg_base;
-	u32 hcc_params, val, temp;
-	u8 cap_length;
-
-	base = ioremap_nocache(pci_resource_start(pdev, 0),
-				pci_resource_len(pdev, 0));
-	if (base == NULL) return;
-
-	cap_length = readb(base);
-	op_reg_base = base + cap_length;
-	hcc_params = readl(base + EHCI_HCC_PARAMS);
-	hcc_params = (hcc_params >> 8) & 0xff;
-	if (hcc_params) {
-		pci_read_config_dword(pdev, 
-					hcc_params + EHCI_USBLEGSUP,
-					&val);
-		if (((val & 0xff) == 1) && (val & EHCI_USBLEGSUP_BIOS)) {
-			/*
-			 * Ok, BIOS is in smm mode, try to hand off...
-			 */
-			pci_read_config_dword(pdev,
-						hcc_params + EHCI_USBLEGCTLSTS,
-						&temp);
-			pci_write_config_dword(pdev,
-						hcc_params + EHCI_USBLEGCTLSTS,
-						temp | EHCI_USBLEGCTLSTS_SOOE);
-			val |= EHCI_USBLEGSUP_OS;
-			pci_write_config_dword(pdev, 
-						hcc_params + EHCI_USBLEGSUP, 
-						val);
-
-			wait_time = 500;
-			do {
-				msleep(10);
-				wait_time -= 10;
-				pci_read_config_dword(pdev,
-						hcc_params + EHCI_USBLEGSUP,
-						&val);
-			} while (wait_time && (val & EHCI_USBLEGSUP_BIOS));
-			if (!wait_time) {
-				/*
-				 * well, possibly buggy BIOS...
-				 */
-				printk(KERN_WARNING "EHCI early BIOS handoff "
-						"failed (BIOS bug ?)\n");
-				pci_write_config_dword(pdev,
-						hcc_params + EHCI_USBLEGSUP,
-						EHCI_USBLEGSUP_OS);
-				pci_write_config_dword(pdev,
-						hcc_params + EHCI_USBLEGCTLSTS,
-						0);
-			}
-		}
-	}
-
-	/*
-	 * halt EHCI & disable its interrupts in any case
-	 */
-	val = readl(op_reg_base + EHCI_USBSTS);
-	if ((val & EHCI_USBSTS_HALTED) == 0) {
-		val = readl(op_reg_base + EHCI_USBCMD);
-		val &= ~EHCI_USBCMD_RUN;
-		writel(val, op_reg_base + EHCI_USBCMD);
-
-		wait_time = 2000;
-		delta = 100;
-		do {
-			writel(0x3f, op_reg_base + EHCI_USBSTS);
-			udelay(delta);
-			wait_time -= delta;
-			val = readl(op_reg_base + EHCI_USBSTS);
-			if ((val == ~(u32)0) || (val & EHCI_USBSTS_HALTED)) {
-				break;
-			}
-		} while (wait_time > 0);
-	}
-	writel(0, op_reg_base + EHCI_USBINTR);
-	writel(0x3f, op_reg_base + EHCI_USBSTS);
-
-	iounmap(base);
-
-	return;
-}
-
-
-
-static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
-{
-	if (!usb_early_handoff)
-		return;
-
-	if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x00)) { /* UHCI */
-		quirk_usb_handoff_uhci(pdev);
-	} else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x10)) { /* OHCI */
-		quirk_usb_handoff_ohci(pdev);
-	} else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x20)) { /* EHCI */
-		quirk_usb_disable_ehci(pdev);
-	}
-
-	return;
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_usb_early_handoff);
-
 /*
  * ... This is further complicated by the fact that some SiS96x south
  * bridges pretend to be 85C503/5513 instead.  In that case see if we
diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
index df014c2..aa554f9 100644
--- a/drivers/usb/Makefile
+++ b/drivers/usb/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_USB)		+= core/
 
 obj-$(CONFIG_USB_MON)		+= mon/
 
+obj-$(CONFIG_PCI)		+= host/
 obj-$(CONFIG_USB_EHCI_HCD)	+= host/
 obj-$(CONFIG_USB_ISP116X_HCD)	+= host/
 obj-$(CONFIG_USB_OHCI_HCD)	+= host/
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 350d14f..58321d3 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -1,8 +1,9 @@
 #
-# Makefile for USB Host Controller Driver
-# framework and drivers
+# Makefile for USB Host Controller Drivers
 #
 
+obj-$(CONFIG_PCI)		+= pci-quirks.o
+
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
 obj-$(CONFIG_USB_ISP116X_HCD)	+= isp116x-hcd.o
 obj-$(CONFIG_USB_OHCI_HCD)	+= ohci-hcd.o
diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c
new file mode 100644
index 0000000..8ee5c3e
--- /dev/null
+++ b/drivers/usb/host/pci-quirks.c
@@ -0,0 +1,272 @@
+/*
+ * This file contains code to reset and initialize USB host controllers.
+ * Some of it includes work-arounds for PCI hardware and BIOS quirks.
+ * It may need to run early during booting -- before USB would normally
+ * initialize -- to ensure that Linux doesn't use any legacy modes.
+ *
+ *  Copyright (c) 1999 Martin Mares <mj@ucw.cz>
+ *  (and others)
+ */
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/acpi.h>
+
+
+/*
+ * PIIX3 USB: We have to disable USB interrupts that are
+ * hardwired to PIRQD# and may be shared with an
+ * external device.
+ *
+ * Legacy Support Register (LEGSUP):
+ *     bit13:  USB PIRQ Enable (USBPIRQDEN),
+ *     bit4:   Trap/SMI On IRQ Enable (USBSMIEN).
+ *
+ * We mask out all r/wc bits, too.
+ */
+static void __devinit quirk_piix3_usb(struct pci_dev *dev)
+{
+	u16 legsup;
+
+	pci_read_config_word(dev, 0xc0, &legsup);
+	legsup &= 0x50ef;
+	pci_write_config_word(dev, 0xc0, legsup);
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82371SB_2,	quirk_piix3_usb );
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82371AB_2,	quirk_piix3_usb );
+
+
+/* FIXME these should be the guts of hcd->reset() methods; resolve all
+ * the differences between this version and the HCD's version.
+ */
+
+#define UHCI_USBLEGSUP		0xc0		/* legacy support */
+#define UHCI_USBCMD		0		/* command register */
+#define UHCI_USBSTS		2		/* status register */
+#define UHCI_USBINTR		4		/* interrupt register */
+#define UHCI_USBLEGSUP_DEFAULT	0x2000		/* only PIRQ enable set */
+#define UHCI_USBCMD_RUN		(1 << 0)	/* RUN/STOP bit */
+#define UHCI_USBCMD_GRESET	(1 << 2)	/* Global reset */
+#define UHCI_USBCMD_CONFIGURE	(1 << 6)	/* config semaphore */
+#define UHCI_USBSTS_HALTED	(1 << 5)	/* HCHalted bit */
+
+#define OHCI_CONTROL		0x04
+#define OHCI_CMDSTATUS		0x08
+#define OHCI_INTRSTATUS		0x0c
+#define OHCI_INTRENABLE		0x10
+#define OHCI_INTRDISABLE	0x14
+#define OHCI_OCR		(1 << 3)	/* ownership change request */
+#define OHCI_CTRL_IR		(1 << 8)	/* interrupt routing */
+#define OHCI_INTR_OC		(1 << 30)	/* ownership change */
+
+#define EHCI_HCC_PARAMS		0x08		/* extended capabilities */
+#define EHCI_USBCMD		0		/* command register */
+#define EHCI_USBCMD_RUN		(1 << 0)	/* RUN/STOP bit */
+#define EHCI_USBSTS		4		/* status register */
+#define EHCI_USBSTS_HALTED	(1 << 12)	/* HCHalted bit */
+#define EHCI_USBINTR		8		/* interrupt register */
+#define EHCI_USBLEGSUP		0		/* legacy support register */
+#define EHCI_USBLEGSUP_BIOS	(1 << 16)	/* BIOS semaphore */
+#define EHCI_USBLEGSUP_OS	(1 << 24)	/* OS semaphore */
+#define EHCI_USBLEGCTLSTS	4		/* legacy control/status */
+#define EHCI_USBLEGCTLSTS_SOOE	(1 << 13)	/* SMI on ownership change */
+
+int usb_early_handoff __devinitdata = 0;
+static int __init usb_handoff_early(char *str)
+{
+	usb_early_handoff = 1;
+	return 0;
+}
+__setup("usb-handoff", usb_handoff_early);
+
+static void __devinit quirk_usb_handoff_uhci(struct pci_dev *pdev)
+{
+	unsigned long base = 0;
+	int wait_time, delta;
+	u16 val, sts;
+	int i;
+
+	for (i = 0; i < PCI_ROM_RESOURCE; i++)
+		if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
+			base = pci_resource_start(pdev, i);
+			break;
+		}
+
+	if (!base)
+		return;
+
+	/*
+	 * stop controller
+	 */
+	sts = inw(base + UHCI_USBSTS);
+	val = inw(base + UHCI_USBCMD);
+	val &= ~(u16)(UHCI_USBCMD_RUN | UHCI_USBCMD_CONFIGURE);
+	outw(val, base + UHCI_USBCMD);
+
+	/*
+	 * wait while it stops if it was running
+	 */
+	if ((sts & UHCI_USBSTS_HALTED) == 0)
+	{
+		wait_time = 1000;
+		delta = 100;
+
+		do {
+			outw(0x1f, base + UHCI_USBSTS);
+			udelay(delta);
+			wait_time -= delta;
+			val = inw(base + UHCI_USBSTS);
+			if (val & UHCI_USBSTS_HALTED)
+				break;
+		} while (wait_time > 0);
+	}
+
+	/*
+	 * disable interrupts & legacy support
+	 */
+	outw(0, base + UHCI_USBINTR);
+	outw(0x1f, base + UHCI_USBSTS);
+	pci_read_config_word(pdev, UHCI_USBLEGSUP, &val);
+	if (val & 0xbf)
+		pci_write_config_word(pdev, UHCI_USBLEGSUP, UHCI_USBLEGSUP_DEFAULT);
+
+}
+
+static void __devinit quirk_usb_handoff_ohci(struct pci_dev *pdev)
+{
+	void __iomem *base;
+	int wait_time;
+
+	base = ioremap_nocache(pci_resource_start(pdev, 0),
+				     pci_resource_len(pdev, 0));
+	if (base == NULL) return;
+
+	if (readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
+		wait_time = 500; /* 0.5 seconds */
+		writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
+		writel(OHCI_OCR, base + OHCI_CMDSTATUS);
+		while (wait_time > 0 &&
+				readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
+			wait_time -= 10;
+			msleep(10);
+		}
+	}
+
+	/*
+	 * disable interrupts
+	 */
+	writel(~(u32)0, base + OHCI_INTRDISABLE);
+	writel(~(u32)0, base + OHCI_INTRSTATUS);
+
+	iounmap(base);
+}
+
+static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev)
+{
+	int wait_time, delta;
+	void __iomem *base, *op_reg_base;
+	u32 hcc_params, val, temp;
+	u8 cap_length;
+
+	base = ioremap_nocache(pci_resource_start(pdev, 0),
+				pci_resource_len(pdev, 0));
+	if (base == NULL) return;
+
+	cap_length = readb(base);
+	op_reg_base = base + cap_length;
+	hcc_params = readl(base + EHCI_HCC_PARAMS);
+	hcc_params = (hcc_params >> 8) & 0xff;
+	if (hcc_params) {
+		pci_read_config_dword(pdev,
+					hcc_params + EHCI_USBLEGSUP,
+					&val);
+		if (((val & 0xff) == 1) && (val & EHCI_USBLEGSUP_BIOS)) {
+			/*
+			 * Ok, BIOS is in smm mode, try to hand off...
+			 */
+			pci_read_config_dword(pdev,
+						hcc_params + EHCI_USBLEGCTLSTS,
+						&temp);
+			pci_write_config_dword(pdev,
+						hcc_params + EHCI_USBLEGCTLSTS,
+						temp | EHCI_USBLEGCTLSTS_SOOE);
+			val |= EHCI_USBLEGSUP_OS;
+			pci_write_config_dword(pdev,
+						hcc_params + EHCI_USBLEGSUP,
+						val);
+
+			wait_time = 500;
+			do {
+				msleep(10);
+				wait_time -= 10;
+				pci_read_config_dword(pdev,
+						hcc_params + EHCI_USBLEGSUP,
+						&val);
+			} while (wait_time && (val & EHCI_USBLEGSUP_BIOS));
+			if (!wait_time) {
+				/*
+				 * well, possibly buggy BIOS...
+				 */
+				printk(KERN_WARNING "EHCI early BIOS handoff "
+						"failed (BIOS bug ?)\n");
+				pci_write_config_dword(pdev,
+						hcc_params + EHCI_USBLEGSUP,
+						EHCI_USBLEGSUP_OS);
+				pci_write_config_dword(pdev,
+						hcc_params + EHCI_USBLEGCTLSTS,
+						0);
+			}
+		}
+	}
+
+	/*
+	 * halt EHCI & disable its interrupts in any case
+	 */
+	val = readl(op_reg_base + EHCI_USBSTS);
+	if ((val & EHCI_USBSTS_HALTED) == 0) {
+		val = readl(op_reg_base + EHCI_USBCMD);
+		val &= ~EHCI_USBCMD_RUN;
+		writel(val, op_reg_base + EHCI_USBCMD);
+
+		wait_time = 2000;
+		delta = 100;
+		do {
+			writel(0x3f, op_reg_base + EHCI_USBSTS);
+			udelay(delta);
+			wait_time -= delta;
+			val = readl(op_reg_base + EHCI_USBSTS);
+			if ((val == ~(u32)0) || (val & EHCI_USBSTS_HALTED)) {
+				break;
+			}
+		} while (wait_time > 0);
+	}
+	writel(0, op_reg_base + EHCI_USBINTR);
+	writel(0x3f, op_reg_base + EHCI_USBSTS);
+
+	iounmap(base);
+
+	return;
+}
+
+
+
+static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
+{
+	if (!usb_early_handoff)
+		return;
+
+	if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x00)) { /* UHCI */
+		quirk_usb_handoff_uhci(pdev);
+	} else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x10)) { /* OHCI */
+		quirk_usb_handoff_ohci(pdev);
+	} else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x20)) { /* EHCI */
+		quirk_usb_disable_ehci(pdev);
+	}
+
+	return;
+}
+DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_usb_early_handoff);
-- 
cgit v1.1


From db69087437dd5135a9362da1c37fe072070e8f60 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Tue, 13 Sep 2005 19:56:33 -0700
Subject: [PATCH] usb_interface power state

This updates the handling of power state for USB interfaces.

  - Formalizes an existing invariant:  interface "power state" is a boolean:
    ON when I/O is allowed, and FREEZE otherwise.  It does so by defining
    some inlined helpers, then using them.

  - Adds a useful invariant:  the only interfaces marked active are those
    bound to non-suspended drivers.  Later patches build on this invariant.

  - Simplifies the interface driver API (and removes some error paths) by
    removing the requirement that they record power state changes during
    suspend and resume callbacks.  Now usbcore does that.

A few drivers were simplified to address that last change.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hub.c       |   33 +++++++++------------
 drivers/usb/core/message.c   |    1
 drivers/usb/core/usb.c       |   65 +++++++++++++++++++++++++++++++++----------
 drivers/usb/core/usb.h       |   18 +++++++++++
 drivers/usb/input/hid-core.c |    2 -
 drivers/usb/misc/usbtest.c   |   10 ------
 drivers/usb/net/pegasus.c    |    2 -
 drivers/usb/net/usbnet.c     |    2 -
 8 files changed, 85 insertions(+), 48 deletions(-)
---
 drivers/usb/core/hub.c       | 33 ++++++++++------------
 drivers/usb/core/message.c   |  1 +
 drivers/usb/core/usb.c       | 65 ++++++++++++++++++++++++++++++++++----------
 drivers/usb/core/usb.h       | 18 ++++++++++++
 drivers/usb/input/hid-core.c |  2 --
 drivers/usb/misc/usbtest.c   | 10 -------
 drivers/usb/net/pegasus.c    |  2 --
 drivers/usb/net/usbnet.c     |  2 --
 8 files changed, 85 insertions(+), 48 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index c3e2024..61341d2 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1624,7 +1624,7 @@ static int __usb_suspend_device (struct usb_device *udev, int port1,
 			struct usb_driver	*driver;
 
 			intf = udev->actconfig->interface[i];
-			if (state.event <= intf->dev.power.power_state.event)
+			if (!is_active(intf))
 				continue;
 			if (!intf->dev.driver)
 				continue;
@@ -1632,11 +1632,12 @@ static int __usb_suspend_device (struct usb_device *udev, int port1,
 
 			if (driver->suspend) {
 				status = driver->suspend(intf, state);
-				if (intf->dev.power.power_state.event != state.event
-						|| status)
+				if (status == 0)
+					mark_quiesced(intf);
+				else
 					dev_err(&intf->dev,
-						"suspend %d fail, code %d\n",
-						state.event, status);
+						"suspend error %d\n",
+						status);
 			}
 
 			/* only drivers with suspend() can ever resume();
@@ -1787,7 +1788,7 @@ static int finish_port_resume(struct usb_device *udev)
 			struct usb_driver	*driver;
 
 			intf = udev->actconfig->interface[i];
-			if (intf->dev.power.power_state.event == PM_EVENT_ON)
+			if (is_active(intf))
 				continue;
 			if (!intf->dev.driver) {
 				/* FIXME maybe force to alt 0 */
@@ -1800,12 +1801,14 @@ static int finish_port_resume(struct usb_device *udev)
 				continue;
 
 			/* can we do better than just logging errors? */
+			mark_active(intf);
 			status = driver->resume(intf);
-			if (intf->dev.power.power_state.event != PM_EVENT_ON
-					|| status)
+			if (status < 0) {
+				mark_quiesced(intf);
 				dev_dbg(&intf->dev,
-					"resume fail, state %d code %d\n",
-					intf->dev.power.power_state.event, status);
+					"resume error %d\n",
+					status);
+			}
 		}
 		status = 0;
 
@@ -1952,7 +1955,7 @@ static int remote_wakeup(struct usb_device *udev)
 	return status;
 }
 
-static int hub_suspend(struct usb_interface *intf, pm_message_t state)
+static int hub_suspend(struct usb_interface *intf, pm_message_t msg)
 {
 	struct usb_hub		*hub = usb_get_intfdata (intf);
 	struct usb_device	*hdev = hub->hdev;
@@ -1970,14 +1973,13 @@ static int hub_suspend(struct usb_interface *intf, pm_message_t state)
 		if (!udev)
 			continue;
 		down(&udev->serialize);
-		status = __usb_suspend_device(udev, port1, state);
+		status = __usb_suspend_device(udev, port1, msg);
 		up(&udev->serialize);
 		if (status < 0)
 			dev_dbg(&intf->dev, "suspend port %d --> %d\n",
 				port1, status);
 	}
 
-	intf->dev.power.power_state = state;
 	return 0;
 }
 
@@ -1988,9 +1990,6 @@ static int hub_resume(struct usb_interface *intf)
 	unsigned		port1;
 	int			status;
 
-	if (intf->dev.power.power_state.event == PM_EVENT_ON)
-		return 0;
-
 	for (port1 = 1; port1 <= hdev->maxchild; port1++) {
 		struct usb_device	*udev;
 		u16			portstat, portchange;
@@ -2024,8 +2023,6 @@ static int hub_resume(struct usb_interface *intf)
 		}
 		up(&udev->serialize);
 	}
-	intf->dev.power.power_state = PMSG_ON;
-
 	hub->resume_root_hub = 0;
 	hub_activate(hub);
 	return 0;
diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c
index f9a81e8..ebf59ea 100644
--- a/drivers/usb/core/message.c
+++ b/drivers/usb/core/message.c
@@ -1393,6 +1393,7 @@ free_interfaces:
 			intf->dev.dma_mask = dev->dev.dma_mask;
 			intf->dev.release = release_interface;
 			device_initialize (&intf->dev);
+			mark_quiesced(intf);
 			sprintf (&intf->dev.bus_id[0], "%d-%s:%d.%d",
 				 dev->bus->busnum, dev->devpath,
 				 configuration,
diff --git a/drivers/usb/core/usb.c b/drivers/usb/core/usb.c
index 4c57f3f..6ecfdce 100644
--- a/drivers/usb/core/usb.c
+++ b/drivers/usb/core/usb.c
@@ -107,10 +107,19 @@ static int usb_probe_interface(struct device *dev)
 	id = usb_match_id (intf, driver->id_table);
 	if (id) {
 		dev_dbg (dev, "%s - got id\n", __FUNCTION__);
+
+		/* Interface "power state" doesn't correspond to any hardware
+		 * state whatsoever.  We use it to record when it's bound to
+		 * a driver that may start I/0:  it's not frozen/quiesced.
+		 */
+		mark_active(intf);
 		intf->condition = USB_INTERFACE_BINDING;
 		error = driver->probe (intf, id);
-		intf->condition = error ? USB_INTERFACE_UNBOUND :
-				USB_INTERFACE_BOUND;
+		if (error) {
+			mark_quiesced(intf);
+			intf->condition = USB_INTERFACE_UNBOUND;
+		} else
+			intf->condition = USB_INTERFACE_BOUND;
 	}
 
 	return error;
@@ -136,6 +145,7 @@ static int usb_unbind_interface(struct device *dev)
 			0);
 	usb_set_intfdata(intf, NULL);
 	intf->condition = USB_INTERFACE_UNBOUND;
+	mark_quiesced(intf);
 
 	return 0;
 }
@@ -299,6 +309,7 @@ int usb_driver_claim_interface(struct usb_driver *driver,
 	dev->driver = &driver->driver;
 	usb_set_intfdata(iface, priv);
 	iface->condition = USB_INTERFACE_BOUND;
+	mark_active(iface);
 
 	/* if interface was already added, bind now; else let
 	 * the future device_add() bind it, bypassing probe()
@@ -345,6 +356,7 @@ void usb_driver_release_interface(struct usb_driver *driver,
 	dev->driver = NULL;
 	usb_set_intfdata(iface, NULL);
 	iface->condition = USB_INTERFACE_UNBOUND;
+	mark_quiesced(iface);
 }
 
 /**
@@ -1404,8 +1416,9 @@ void usb_buffer_unmap_sg (struct usb_device *dev, unsigned pipe,
 
 static int usb_generic_suspend(struct device *dev, pm_message_t message)
 {
-	struct usb_interface *intf;
-	struct usb_driver *driver;
+	struct usb_interface	*intf;
+	struct usb_driver	*driver;
+	int			status;
 
 	if (dev->driver == &usb_generic_driver)
 		return usb_suspend_device (to_usb_device(dev), message);
@@ -1417,21 +1430,34 @@ static int usb_generic_suspend(struct device *dev, pm_message_t message)
 	intf = to_usb_interface(dev);
 	driver = to_usb_driver(dev->driver);
 
-	/* there's only one USB suspend state */
-	if (intf->dev.power.power_state.event)
+	/* with no hardware, USB interfaces only use FREEZE and ON states */
+	if (!is_active(intf))
 		return 0;
 
-	if (driver->suspend)
-		return driver->suspend(intf, message);
-	return 0;
+	if (driver->suspend && driver->resume) {
+		status = driver->suspend(intf, message);
+		if (status)
+			dev_err(dev, "%s error %d\n", "suspend", status);
+		else
+			mark_quiesced(intf);
+	} else {
+		// FIXME else if there's no suspend method, disconnect...
+		dev_warn(dev, "no %s?\n", "suspend");
+		status = 0;
+	}
+	return status;
 }
 
 static int usb_generic_resume(struct device *dev)
 {
-	struct usb_interface *intf;
-	struct usb_driver *driver;
+	struct usb_interface	*intf;
+	struct usb_driver	*driver;
+	int			status;
+
+	if (dev->power.power_state.event == PM_EVENT_ON)
+		return 0;
 
-	/* devices resume through their hub */
+	/* devices resume through their hubs */
 	if (dev->driver == &usb_generic_driver)
 		return usb_resume_device (to_usb_device(dev));
 
@@ -1442,8 +1468,19 @@ static int usb_generic_resume(struct device *dev)
 	intf = to_usb_interface(dev);
 	driver = to_usb_driver(dev->driver);
 
-	if (driver->resume)
-		return driver->resume(intf);
+	/* if driver was suspended, it has a resume method;
+	 * however, sysfs can wrongly mark things as suspended
+	 * (on the "no suspend method" FIXME path above)
+	 */
+	mark_active(intf);
+	if (driver->resume) {
+		status = driver->resume(intf);
+		if (status) {
+			dev_err(dev, "%s error %d\n", "resume", status);
+			mark_quiesced(intf);
+		}
+	} else
+		dev_warn(dev, "no %s?\n", "resume");
 	return 0;
 }
 
diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
index e6504f3..3741a99 100644
--- a/drivers/usb/core/usb.h
+++ b/drivers/usb/core/usb.h
@@ -28,6 +28,24 @@ extern void usb_major_cleanup(void);
 extern int usb_host_init(void);
 extern void usb_host_cleanup(void);
 
+/* Interfaces and their "power state" are owned by usbcore */
+
+static inline void mark_active(struct usb_interface *f)
+{
+	f->dev.power.power_state.event = PM_EVENT_ON;
+}
+
+static inline void mark_quiesced(struct usb_interface *f)
+{
+	f->dev.power.power_state.event = PM_EVENT_FREEZE;
+}
+
+static inline int is_active(struct usb_interface *f)
+{
+	return f->dev.power.power_state.event == PM_EVENT_ON;
+}
+
+
 /* for labeling diagnostics */
 extern const char *usbcore_name;
 
diff --git a/drivers/usb/input/hid-core.c b/drivers/usb/input/hid-core.c
index 411a064..f7fcce7 100644
--- a/drivers/usb/input/hid-core.c
+++ b/drivers/usb/input/hid-core.c
@@ -1887,7 +1887,6 @@ static int hid_suspend(struct usb_interface *intf, pm_message_t message)
 	struct hid_device *hid = usb_get_intfdata (intf);
 
 	usb_kill_urb(hid->urbin);
-	intf->dev.power.power_state = PMSG_SUSPEND;
 	dev_dbg(&intf->dev, "suspend\n");
 	return 0;
 }
@@ -1897,7 +1896,6 @@ static int hid_resume(struct usb_interface *intf)
 	struct hid_device *hid = usb_get_intfdata (intf);
 	int status;
 
-	intf->dev.power.power_state = PMSG_ON;
 	if (hid->open)
 		status = usb_submit_urb(hid->urbin, GFP_NOIO);
 	else
diff --git a/drivers/usb/misc/usbtest.c b/drivers/usb/misc/usbtest.c
index 54799eb..d055196 100644
--- a/drivers/usb/misc/usbtest.c
+++ b/drivers/usb/misc/usbtest.c
@@ -1948,21 +1948,11 @@ usbtest_probe (struct usb_interface *intf, const struct usb_device_id *id)
 
 static int usbtest_suspend (struct usb_interface *intf, pm_message_t message)
 {
-	struct usbtest_dev	*dev = usb_get_intfdata (intf);
-
-	down (&dev->sem);
-	intf->dev.power.power_state = PMSG_SUSPEND;
-	up (&dev->sem);
 	return 0;
 }
 
 static int usbtest_resume (struct usb_interface *intf)
 {
-	struct usbtest_dev	*dev = usb_get_intfdata (intf);
-
-	down (&dev->sem);
-	intf->dev.power.power_state = PMSG_ON;
-	up (&dev->sem);
 	return 0;
 }
 
diff --git a/drivers/usb/net/pegasus.c b/drivers/usb/net/pegasus.c
index 6a4ffe6..537eb18 100644
--- a/drivers/usb/net/pegasus.c
+++ b/drivers/usb/net/pegasus.c
@@ -1384,7 +1384,6 @@ static int pegasus_suspend (struct usb_interface *intf, pm_message_t message)
 		usb_kill_urb(pegasus->rx_urb);
 		usb_kill_urb(pegasus->intr_urb);
 	}
-	intf->dev.power.power_state = PMSG_SUSPEND;
 	return 0;
 }
 
@@ -1392,7 +1391,6 @@ static int pegasus_resume (struct usb_interface *intf)
 {
 	struct pegasus *pegasus = usb_get_intfdata(intf);
 
-	intf->dev.power.power_state = PMSG_ON;
 	netif_device_attach (pegasus->net);
 	if (netif_running(pegasus->net)) {
 		pegasus->rx_urb->status = 0;
diff --git a/drivers/usb/net/usbnet.c b/drivers/usb/net/usbnet.c
index fce81d7..74f05c9 100644
--- a/drivers/usb/net/usbnet.c
+++ b/drivers/usb/net/usbnet.c
@@ -1185,7 +1185,6 @@ int usbnet_suspend (struct usb_interface *intf, pm_message_t message)
 	netif_device_detach (dev->net);
 	(void) unlink_urbs (dev, &dev->rxq);
 	(void) unlink_urbs (dev, &dev->txq);
-	intf->dev.power.power_state = PMSG_SUSPEND;
 	return 0;
 }
 EXPORT_SYMBOL_GPL(usbnet_suspend);
@@ -1194,7 +1193,6 @@ int usbnet_resume (struct usb_interface *intf)
 {
 	struct usbnet		*dev = usb_get_intfdata(intf);
 
-	intf->dev.power.power_state = PMSG_ON;
 	netif_device_attach (dev->net);
 	tasklet_schedule (&dev->bh);
 	return 0;
-- 
cgit v1.1


From c9f89fa40cf274130b56475175a35af961d4b165 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Tue, 13 Sep 2005 19:57:04 -0700
Subject: [PATCH] remove suspend-path recursion

This patch removes some recursion in the CONFIG_USB_SUSPEND logic, which
suspended children (of devices or hubs) that weren't already suspended.
When it sees such cases, suspend now just fails cleanly.

That logic was not needed during system-wide sleep state transitions; and
given the current notions of how to manage selective suspend transitions,
we don't want it there either.  Where it was particularly handy was coping
with various limitations of the sysfs "echo -n N > power/state" support.
(These include assuming that "N" is always meaningful to the driver; and
that drivers can only transition to state N from state zero.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/hub.c | 76 ++++++++------------------------------------------
 1 file changed, 12 insertions(+), 64 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 61341d2..d3337d9 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -453,6 +453,7 @@ static void hub_quiesce(struct usb_hub *hub)
 {
 	/* stop khubd and related activity */
 	hub->quiescing = 1;
+	hub->activating = 0;
 	usb_kill_urb(hub->urb);
 	if (hub->has_indicators)
 		cancel_delayed_work(&hub->leds);
@@ -1613,68 +1614,21 @@ static int __usb_suspend_device (struct usb_device *udev, int port1,
 		return 0;
 	}
 
-	/* suspend interface drivers; if this is a hub, it
-	 * suspends the child devices
-	 */
+	/* all interfaces must already be suspended */
 	if (udev->actconfig) {
 		int	i;
 
 		for (i = 0; i < udev->actconfig->desc.bNumInterfaces; i++) {
 			struct usb_interface	*intf;
-			struct usb_driver	*driver;
 
 			intf = udev->actconfig->interface[i];
-			if (!is_active(intf))
-				continue;
-			if (!intf->dev.driver)
-				continue;
-			driver = to_usb_driver(intf->dev.driver);
-
-			if (driver->suspend) {
-				status = driver->suspend(intf, state);
-				if (status == 0)
-					mark_quiesced(intf);
-				else
-					dev_err(&intf->dev,
-						"suspend error %d\n",
-						status);
-			}
-
-			/* only drivers with suspend() can ever resume();
-			 * and after power loss, even they won't.
-			 * bus_rescan_devices() can rebind drivers later.
-			 *
-			 * FIXME the PM core self-deadlocks when unbinding
-			 * drivers during suspend/resume ... everything grabs
-			 * dpm_sem (not a spinlock, ugh).  we want to unbind,
-			 * since we know every driver's probe/disconnect works
-			 * even for drivers that can't suspend.
-			 */
-			if (!driver->suspend || state.event > PM_EVENT_FREEZE) {
-#if 1
-				dev_warn(&intf->dev, "resume is unsafe!\n");
-#else
-				down_write(&usb_bus_type.rwsem);
-				device_release_driver(&intf->dev);
-				up_write(&usb_bus_type.rwsem);
-#endif
+			if (is_active(intf)) {
+				dev_dbg(&intf->dev, "nyet suspended\n");
+				return -EBUSY;
 			}
 		}
 	}
 
-	/*
-	 * FIXME this needs port power off call paths too, to help force
-	 * USB into the "generic" PM model.  At least for devices on
-	 * ports that aren't using ganged switching (usually root hubs).
-	 *
-	 * NOTE: SRP-capable links should adopt more aggressive poweroff
-	 * policies (when HNP doesn't apply) once we have mechanisms to
-	 * turn power back on!  (Likely not before 2.7...)
-	 */
-	if (state.event > PM_EVENT_FREEZE) {
-		dev_warn(&udev->dev, "no poweroff yet, suspending instead\n");
-	}
-
 	/* "global suspend" of the HC-to-USB interface (root hub), or
 	 * "selective suspend" of just one hub-device link.
 	 */
@@ -1960,26 +1914,20 @@ static int hub_suspend(struct usb_interface *intf, pm_message_t msg)
 	struct usb_hub		*hub = usb_get_intfdata (intf);
 	struct usb_device	*hdev = hub->hdev;
 	unsigned		port1;
-	int			status;
-
-	/* stop khubd and related activity */
-	hub_quiesce(hub);
 
-	/* then suspend every port */
+	/* fail if children aren't already suspended */
 	for (port1 = 1; port1 <= hdev->maxchild; port1++) {
 		struct usb_device	*udev;
 
 		udev = hdev->children [port1-1];
-		if (!udev)
-			continue;
-		down(&udev->serialize);
-		status = __usb_suspend_device(udev, port1, msg);
-		up(&udev->serialize);
-		if (status < 0)
-			dev_dbg(&intf->dev, "suspend port %d --> %d\n",
-				port1, status);
+		if (udev && udev->state != USB_STATE_SUSPENDED) {
+			dev_dbg(&intf->dev, "port %d nyet suspended\n", port1);
+			return -EBUSY;
+		}
 	}
 
+	/* stop khubd and related activity */
+	hub_quiesce(hub);
 	return 0;
 }
 
-- 
cgit v1.1


From 390a8c345e6415cbf811232feedac70b56c9fc8d Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Tue, 13 Sep 2005 19:57:27 -0700
Subject: [PATCH] remove usb_suspend_device() parameter

This patch removes the extra usb_suspend_device() parameter.  The original
reason to pass that parameter was so that this routine could suspend any
active children.  A previous patch removed that functionality ... leaving
no reason to pass the parameter.  A close analogy is pci_set_power_state,
which doesn't need a pm_message_t either.

On the internal code path that comes through the driver model, the parameter
is now used to distinguish cases where USB devices need to "freeze" but not
suspend.   It also checks for an error case that's accessible through sysfs:
attempting to suspend a device before its interfaces (or for hubs, ports).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hub.c         |   34 +++++++++++++++++++++-------------
 drivers/usb/core/usb.c         |   23 +++++++++++++++++++++--
 drivers/usb/host/ehci-hcd.c    |    2 +-
 drivers/usb/host/isp116x-hcd.c |    2 +-
 drivers/usb/host/ohci-pci.c    |    2 +-
 include/linux/usb.h            |    2 +-
 6 files changed, 46 insertions(+), 19 deletions(-)
---
 drivers/usb/core/hub.c         | 34 +++++++++++++++++++++-------------
 drivers/usb/core/usb.c         | 23 +++++++++++++++++++++--
 drivers/usb/host/ehci-hcd.c    |  2 +-
 drivers/usb/host/isp116x-hcd.c |  2 +-
 drivers/usb/host/ohci-pci.c    |  2 +-
 5 files changed, 45 insertions(+), 18 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index d3337d9..33127b8 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1323,11 +1323,9 @@ int usb_new_device(struct usb_device *udev)
 		 * (Includes HNP test device.)
 		 */
 		if (udev->bus->b_hnp_enable || udev->bus->is_b_host) {
-			static int __usb_suspend_device (struct usb_device *,
-						int port1, pm_message_t state);
-			err = __usb_suspend_device(udev,
-					udev->bus->otg_port,
-					PMSG_SUSPEND);
+			static int __usb_suspend_device(struct usb_device *,
+						int port1);
+			err = __usb_suspend_device(udev, udev->bus->otg_port);
 			if (err < 0)
 				dev_dbg(&udev->dev, "HNP fail, %d\n", err);
 		}
@@ -1517,7 +1515,7 @@ static void hub_port_logical_disconnect(struct usb_hub *hub, int port1)
 	/* FIXME let caller ask to power down the port:
 	 *  - some devices won't enumerate without a VBUS power cycle
 	 *  - SRP saves power that way
-	 *  - usb_suspend_device(dev, PMSG_SUSPEND)
+	 *  - ... new call, TBD ...
 	 * That's easy if this hub can switch power per-port, and
 	 * khubd reactivates the port later (timer, SRP, etc).
 	 * Powerdown must be optional, because of reset/DFU.
@@ -1599,9 +1597,12 @@ static int hub_port_suspend(struct usb_hub *hub, int port1,
  * Other than re-initializing the hub (plug/unplug, except for root hubs),
  * Linux (2.6) currently has NO mechanisms to initiate that:  no khubd
  * timer, no SRP, no requests through sysfs.
+ *
+ * If CONFIG_USB_SUSPEND isn't enabled, devices only really suspend when
+ * the root hub for their bus goes into global suspend ... so we don't
+ * (falsely) update the device power state to say it suspended.
  */
-static int __usb_suspend_device (struct usb_device *udev, int port1,
-				 pm_message_t state)
+static int __usb_suspend_device (struct usb_device *udev, int port1)
 {
 	int	status;
 
@@ -1648,14 +1649,13 @@ static int __usb_suspend_device (struct usb_device *udev, int port1,
 				udev);
 
 	if (status == 0)
-		udev->dev.power.power_state = state;
+		udev->dev.power.power_state = PMSG_SUSPEND;
 	return status;
 }
 
 /**
  * usb_suspend_device - suspend a usb device
  * @udev: device that's no longer in active use
- * @state: PMSG_SUSPEND to suspend
  * Context: must be able to sleep; device not locked
  *
  * Suspends a USB device that isn't in active use, conserving power.
@@ -1664,13 +1664,16 @@ static int __usb_suspend_device (struct usb_device *udev, int port1,
  * suspend by the host, using usb_resume_device().  It's also routine
  * to disconnect devices while they are suspended.
  *
+ * This only affects the USB hardware for a device; its interfaces
+ * (and, for hubs, child devices) must already have been suspended.
+ *
  * Suspending OTG devices may trigger HNP, if that's been enabled
  * between a pair of dual-role devices.  That will change roles, such
  * as from A-Host to A-Peripheral or from B-Host back to B-Peripheral.
  *
  * Returns 0 on success, else negative errno.
  */
-int usb_suspend_device(struct usb_device *udev, pm_message_t state)
+int usb_suspend_device(struct usb_device *udev)
 {
 	int	port1, status;
 
@@ -1678,12 +1681,15 @@ int usb_suspend_device(struct usb_device *udev, pm_message_t state)
 	if (port1 < 0)
 		return port1;
 
-	status = __usb_suspend_device(udev, port1, state);
+	status = __usb_suspend_device(udev, port1);
 	usb_unlock_device(udev);
 	return status;
 }
 
 /*
+ * If the USB "suspend" state is in use (rather than "global suspend"),
+ * many devices will be individually taken out of suspend state using
+ * special" resume" signaling.  These routines kick in shortly after
  * hardware resume signaling is finished, either because of selective
  * resume (by host) or remote wakeup (by device) ... now see what changed
  * in the tree that's rooted at this device.
@@ -1986,13 +1992,15 @@ void usb_resume_root_hub(struct usb_device *hdev)
 
 #else	/* !CONFIG_USB_SUSPEND */
 
-int usb_suspend_device(struct usb_device *udev, pm_message_t state)
+int usb_suspend_device(struct usb_device *udev)
 {
+	/* state does NOT lie by saying it's USB_STATE_SUSPENDED! */
 	return 0;
 }
 
 int usb_resume_device(struct usb_device *udev)
 {
+	udev->dev.power_state.event = PM_EVENT_ON;
 	return 0;
 }
 
diff --git a/drivers/usb/core/usb.c b/drivers/usb/core/usb.c
index 6ecfdce..e89dbd4 100644
--- a/drivers/usb/core/usb.c
+++ b/drivers/usb/core/usb.c
@@ -1414,14 +1414,33 @@ void usb_buffer_unmap_sg (struct usb_device *dev, unsigned pipe,
 			usb_pipein (pipe) ? DMA_FROM_DEVICE : DMA_TO_DEVICE);
 }
 
+static int verify_suspended(struct device *dev, void *unused)
+{
+	return (dev->power.power_state.event == PM_EVENT_ON) ? -EBUSY : 0;
+}
+
 static int usb_generic_suspend(struct device *dev, pm_message_t message)
 {
 	struct usb_interface	*intf;
 	struct usb_driver	*driver;
 	int			status;
 
-	if (dev->driver == &usb_generic_driver)
-		return usb_suspend_device (to_usb_device(dev), message);
+	/* USB devices enter SUSPEND state through their hubs, but can be
+	 * marked for FREEZE as soon as their children are already idled.
+	 */
+	if (dev->driver == &usb_generic_driver) {
+		if (dev->power.power_state.event == message.event)
+			return 0;
+		/* we need to rule out bogus requests through sysfs */
+		status = device_for_each_child(dev, NULL, verify_suspended);
+		if (status)
+			return status;
+		if (message.event == PM_EVENT_FREEZE) {
+			dev->power.power_state = message;
+			return 0;
+		}
+ 		return usb_suspend_device (to_usb_device(dev));
+	}
 
 	if ((dev->driver == NULL) ||
 	    (dev->driver_data == &usb_generic_driver_data))
diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index b3eb026..513fccb 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -759,7 +759,7 @@ static int ehci_suspend (struct usb_hcd *hcd, pm_message_t message)
 		msleep (100);
 
 #ifdef	CONFIG_USB_SUSPEND
-	(void) usb_suspend_device (hcd->self.root_hub, message);
+	(void) usb_suspend_device (hcd->self.root_hub);
 #else
 	usb_lock_device (hcd->self.root_hub);
 	(void) ehci_hub_suspend (hcd);
diff --git a/drivers/usb/host/isp116x-hcd.c b/drivers/usb/host/isp116x-hcd.c
index 642f350..554d602 100644
--- a/drivers/usb/host/isp116x-hcd.c
+++ b/drivers/usb/host/isp116x-hcd.c
@@ -1781,7 +1781,7 @@ static int isp116x_suspend(struct device *dev, pm_message_t state)
 
 	VDBG("%s: state %x\n", __func__, state);
 
-	ret = usb_suspend_device(hcd->self.root_hub, state);
+	ret = usb_suspend_device(hcd->self.root_hub);
 	if (!ret) {
 		dev->power.power_state = state;
 		INFO("%s suspended\n", hcd_name);
diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c
index eede6be..41e8598 100644
--- a/drivers/usb/host/ohci-pci.c
+++ b/drivers/usb/host/ohci-pci.c
@@ -119,7 +119,7 @@ static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
 		msleep (100);
 
 #ifdef	CONFIG_USB_SUSPEND
-	(void) usb_suspend_device (hcd->self.root_hub, message);
+	(void) usb_suspend_device (hcd->self.root_hub);
 #else
 	usb_lock_device (hcd->self.root_hub);
 	(void) ohci_hub_suspend (hcd);
-- 
cgit v1.1


From dbc3887e7df4be78b33a83b97fde5d5f9a389859 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Tue, 13 Sep 2005 19:57:36 -0700
Subject: [PATCH] remove duplicated resume path code

This gets rid of some inconsistently duplicated logic to resume interfaces.
Similar code was in both finish_port_resume() and in usb_generic_resume().
Now there is just one copy of that code, accessed regardless of whether
CONFIG_USB_SUSPEND is enabled.  Fault handling is also more consistent.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/hub.c | 33 +++++----------------------------
 1 file changed, 5 insertions(+), 28 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 33127b8..b2ae9b6 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1723,6 +1723,7 @@ static int finish_port_resume(struct usb_device *udev)
 			status);
 	else if (udev->actconfig) {
 		unsigned	i;
+		int		(*resume)(struct device *);
 
 		le16_to_cpus(&devstatus);
 		if (devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)) {
@@ -1741,35 +1742,11 @@ static int finish_port_resume(struct usb_device *udev)
 		}
 
 		/* resume interface drivers; if this is a hub, it
-		 * resumes the child devices
+		 * may have a child resume event to deal with soon
 		 */
-		for (i = 0; i < udev->actconfig->desc.bNumInterfaces; i++) {
-			struct usb_interface	*intf;
-			struct usb_driver	*driver;
-
-			intf = udev->actconfig->interface[i];
-			if (is_active(intf))
-				continue;
-			if (!intf->dev.driver) {
-				/* FIXME maybe force to alt 0 */
-				continue;
-			}
-			driver = to_usb_driver(intf->dev.driver);
-
-			/* bus_rescan_devices() may rebind drivers */
-			if (!driver->resume)
-				continue;
-
-			/* can we do better than just logging errors? */
-			mark_active(intf);
-			status = driver->resume(intf);
-			if (status < 0) {
-				mark_quiesced(intf);
-				dev_dbg(&intf->dev,
-					"resume error %d\n",
-					status);
-			}
-		}
+		resume = udev->dev.bus->resume;
+		for (i = 0; i < udev->actconfig->desc.bNumInterfaces; i++)
+			(void) resume(&udev->actconfig->interface[i]->dev);
 		status = 0;
 
 	} else if (udev->devnum <= 0) {
-- 
cgit v1.1


From 8ad7fe16df5e07320626be83fbba6d1c6bda5ec0 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Tue, 13 Sep 2005 19:59:11 -0700
Subject: [PATCH] remove some USB_SUSPEND dependencies

This simplifies some of the PM-related #ifdeffing by recognizing
that USB_SUSPEND depends on PM.  Also, OHCI drivers were often
testing for USB_SUSPEND when they should have tested just PM.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hcd.c          |    2 ++
 drivers/usb/host/ohci-hcd.c     |    2 +-
 drivers/usb/host/ohci-hub.c     |    4 ++--
 drivers/usb/host/ohci-omap.c    |    2 +-
 drivers/usb/host/ohci-pci.c     |    2 +-
 drivers/usb/host/ohci-ppc-soc.c |    4 ++--
 drivers/usb/host/ohci-pxa27x.c  |    2 +-
 drivers/usb/host/ohci-s3c2410.c |    3 +--
 drivers/usb/host/ohci-sa1111.c  |    2 +-
 9 files changed, 12 insertions(+), 11 deletions(-)
---
 drivers/usb/core/hcd.c          | 2 ++
 drivers/usb/host/ohci-hcd.c     | 2 +-
 drivers/usb/host/ohci-hub.c     | 4 ++--
 drivers/usb/host/ohci-omap.c    | 2 +-
 drivers/usb/host/ohci-pci.c     | 2 +-
 drivers/usb/host/ohci-ppc-soc.c | 4 ++--
 drivers/usb/host/ohci-pxa27x.c  | 2 +-
 drivers/usb/host/ohci-s3c2410.c | 3 +--
 drivers/usb/host/ohci-sa1111.c  | 2 +-
 9 files changed, 12 insertions(+), 11 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 14c47a1..5e8ade0 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -1431,6 +1431,8 @@ rescan:
 
 /*-------------------------------------------------------------------------*/
 
+/* FIXME make this #ifdef CONFIG_PM ... update root hubs, retest */
+
 #ifdef	CONFIG_USB_SUSPEND
 
 static int hcd_hub_suspend (struct usb_bus *bus)
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index f8da8c7..c26ab5f 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -791,7 +791,7 @@ static void ohci_stop (struct usb_hcd *hcd)
 
 /* must not be called from interrupt context */
 
-#if	defined(CONFIG_USB_SUSPEND) || defined(CONFIG_PM)
+#ifdef	CONFIG_PM
 
 static int ohci_restart (struct ohci_hcd *ohci)
 {
diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c
index ce7b28d..b96948e 100644
--- a/drivers/usb/host/ohci-hub.c
+++ b/drivers/usb/host/ohci-hub.c
@@ -36,7 +36,7 @@
 
 /*-------------------------------------------------------------------------*/
 
-#if	defined(CONFIG_USB_SUSPEND) || defined(CONFIG_PM)
+#ifdef	CONFIG_PM
 
 #define OHCI_SCHED_ENABLES \
 	(OHCI_CTRL_CLE|OHCI_CTRL_BLE|OHCI_CTRL_PLE|OHCI_CTRL_IE)
@@ -294,7 +294,7 @@ static void ohci_rh_resume (void *_hcd)
 	ohci_dbg(ohci, "rh_resume ??\n");
 }
 
-#endif	/* CONFIG_USB_SUSPEND || CONFIG_PM */
+#endif	/* CONFIG_PM */
 
 /*-------------------------------------------------------------------------*/
 
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index a574216..e67c07d 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -420,7 +420,7 @@ static const struct hc_driver ohci_omap_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
-#ifdef	CONFIG_USB_SUSPEND
+#ifdef	CONFIG_PM
 	.hub_suspend =		ohci_hub_suspend,
 	.hub_resume =		ohci_hub_resume,
 #endif
diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c
index 41e8598..0afa237 100644
--- a/drivers/usb/host/ohci-pci.c
+++ b/drivers/usb/host/ohci-pci.c
@@ -218,7 +218,7 @@ static const struct hc_driver ohci_pci_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
-#ifdef	CONFIG_USB_SUSPEND
+#ifdef	CONFIG_PM
 	.hub_suspend =		ohci_hub_suspend,
 	.hub_resume =		ohci_hub_resume,
 #endif
diff --git a/drivers/usb/host/ohci-ppc-soc.c b/drivers/usb/host/ohci-ppc-soc.c
index 2515333..ec20710 100644
--- a/drivers/usb/host/ohci-ppc-soc.c
+++ b/drivers/usb/host/ohci-ppc-soc.c
@@ -163,7 +163,7 @@ static const struct hc_driver ohci_ppc_soc_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
-#ifdef	CONFIG_USB_SUSPEND
+#ifdef	CONFIG_PM
 	.hub_suspend =		ohci_hub_suspend,
 	.hub_resume =		ohci_hub_resume,
 #endif
@@ -196,7 +196,7 @@ static struct device_driver ohci_hcd_ppc_soc_driver = {
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_ppc_soc_drv_probe,
 	.remove		= ohci_hcd_ppc_soc_drv_remove,
-#if	defined(CONFIG_USB_SUSPEND) || defined(CONFIG_PM)
+#ifdef	CONFIG_PM
 	/*.suspend	= ohci_hcd_ppc_soc_drv_suspend,*/
 	/*.resume	= ohci_hcd_ppc_soc_drv_resume,*/
 #endif
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index f042261..986c4f6 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -278,7 +278,7 @@ static const struct hc_driver ohci_pxa27x_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
-#ifdef  CONFIG_USB_SUSPEND
+#ifdef  CONFIG_PM
 	.hub_suspend =		ohci_hub_suspend,
 	.hub_resume =		ohci_hub_resume,
 #endif
diff --git a/drivers/usb/host/ohci-s3c2410.c b/drivers/usb/host/ohci-s3c2410.c
index da7d547..8cf12b2 100644
--- a/drivers/usb/host/ohci-s3c2410.c
+++ b/drivers/usb/host/ohci-s3c2410.c
@@ -448,8 +448,7 @@ static const struct hc_driver ohci_s3c2410_hc_driver = {
 	 */
 	.hub_status_data =	ohci_s3c2410_hub_status_data,
 	.hub_control =		ohci_s3c2410_hub_control,
-
-#if defined(CONFIG_USB_SUSPEND) && 0
+#ifdef	CONFIG_PM
 	.hub_suspend =		ohci_hub_suspend,
 	.hub_resume =		ohci_hub_resume,
 #endif
diff --git a/drivers/usb/host/ohci-sa1111.c b/drivers/usb/host/ohci-sa1111.c
index 814d2be..7dd1f41 100644
--- a/drivers/usb/host/ohci-sa1111.c
+++ b/drivers/usb/host/ohci-sa1111.c
@@ -235,7 +235,7 @@ static const struct hc_driver ohci_sa1111_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
-#ifdef	CONFIG_USB_SUSPEND
+#ifdef	CONFIG_PM
 	.hub_suspend =		ohci_hub_suspend,
 	.hub_resume =		ohci_hub_resume,
 #endif
-- 
cgit v1.1


From e08fb39b771dd7dcba405669b5384fe9929e1caf Mon Sep 17 00:00:00 2001
From: Matt Porter <mporter@kernel.crashing.org>
Date: Mon, 19 Sep 2005 09:40:24 -0700
Subject: [PATCH] USB: Fix usb hub build

Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hub.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
---
 drivers/usb/core/hub.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index b2ae9b6..6600644 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1977,7 +1977,7 @@ int usb_suspend_device(struct usb_device *udev)
 
 int usb_resume_device(struct usb_device *udev)
 {
-	udev->dev.power_state.event = PM_EVENT_ON;
+	udev->dev.power.power_state.event = PM_EVENT_ON;
 	return 0;
 }
 
-- 
cgit v1.1


From 8b4cd42134fbd3c9a9a5c3467d31717798219b1b Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Fri, 16 Sep 2005 14:17:45 -0400
Subject: [PATCH] USB: UHCI: Remove unused fields and unneeded tests for NULL

This patch (as562) removes from the uhci-hcd driver a few unused fields
and some unnecessary tests against NULL and assignments to NULL.  In fact
it wasn't until fairly recently that the tests became unnecessary.
Before last winter it was possible that the driver's stop() routine would
get called even if the start() routine returned an error, but now that
can't happen.  Hence there's no longer any need to check for partial
initialization.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/uhci-debug.c |  1 -
 drivers/usb/host/uhci-hcd.c   | 44 ++++++++++---------------------------------
 drivers/usb/host/uhci-hcd.h   |  3 ---
 drivers/usb/host/uhci-q.c     |  5 -----
 4 files changed, 10 insertions(+), 43 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/uhci-debug.c b/drivers/usb/host/uhci-debug.c
index 4538a98..04eddd7 100644
--- a/drivers/usb/host/uhci-debug.c
+++ b/drivers/usb/host/uhci-debug.c
@@ -348,7 +348,6 @@ static int uhci_show_urbp(struct uhci_hcd *uhci, struct urb_priv *urbp, char *bu
 
 	if (urbp->urb->status != -EINPROGRESS)
 		out += sprintf(out, "Status=%d ", urbp->urb->status);
-	//out += sprintf(out, "Inserttime=%lx ",urbp->inserttime);
 	//out += sprintf(out, "FSBRtime=%lx ",urbp->fsbrtime);
 
 	count = 0;
diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c
index 0c02489..17de9ee 100644
--- a/drivers/usb/host/uhci-hcd.c
+++ b/drivers/usb/host/uhci-hcd.c
@@ -437,36 +437,18 @@ static void release_uhci(struct uhci_hcd *uhci)
 	int i;
 
 	for (i = 0; i < UHCI_NUM_SKELQH; i++)
-		if (uhci->skelqh[i]) {
-			uhci_free_qh(uhci, uhci->skelqh[i]);
-			uhci->skelqh[i] = NULL;
-		}
+		uhci_free_qh(uhci, uhci->skelqh[i]);
 
-	if (uhci->term_td) {
-		uhci_free_td(uhci, uhci->term_td);
-		uhci->term_td = NULL;
-	}
+	uhci_free_td(uhci, uhci->term_td);
 
-	if (uhci->qh_pool) {
-		dma_pool_destroy(uhci->qh_pool);
-		uhci->qh_pool = NULL;
-	}
+	dma_pool_destroy(uhci->qh_pool);
 
-	if (uhci->td_pool) {
-		dma_pool_destroy(uhci->td_pool);
-		uhci->td_pool = NULL;
-	}
+	dma_pool_destroy(uhci->td_pool);
 
-	if (uhci->fl) {
-		dma_free_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
-				uhci->fl, uhci->fl->dma_handle);
-		uhci->fl = NULL;
-	}
+	dma_free_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
+			uhci->fl, uhci->fl->dma_handle);
 
-	if (uhci->dentry) {
-		debugfs_remove(uhci->dentry);
-		uhci->dentry = NULL;
-	}
+	debugfs_remove(uhci->dentry);
 }
 
 static int uhci_reset(struct usb_hcd *hcd)
@@ -690,31 +672,25 @@ static int uhci_start(struct usb_hcd *hcd)
  * error exits:
  */
 err_alloc_skelqh:
-	for (i = 0; i < UHCI_NUM_SKELQH; i++)
-		if (uhci->skelqh[i]) {
+	for (i = 0; i < UHCI_NUM_SKELQH; i++) {
+		if (uhci->skelqh[i])
 			uhci_free_qh(uhci, uhci->skelqh[i]);
-			uhci->skelqh[i] = NULL;
-		}
+	}
 
 	uhci_free_td(uhci, uhci->term_td);
-	uhci->term_td = NULL;
 
 err_alloc_term_td:
 	dma_pool_destroy(uhci->qh_pool);
-	uhci->qh_pool = NULL;
 
 err_create_qh_pool:
 	dma_pool_destroy(uhci->td_pool);
-	uhci->td_pool = NULL;
 
 err_create_td_pool:
 	dma_free_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
 			uhci->fl, uhci->fl->dma_handle);
-	uhci->fl = NULL;
 
 err_alloc_fl:
 	debugfs_remove(uhci->dentry);
-	uhci->dentry = NULL;
 
 err_create_debug_entry:
 	return retval;
diff --git a/drivers/usb/host/uhci-hcd.h b/drivers/usb/host/uhci-hcd.h
index 282f40b..1c161b4 100644
--- a/drivers/usb/host/uhci-hcd.h
+++ b/drivers/usb/host/uhci-hcd.h
@@ -205,8 +205,6 @@ struct uhci_td {
 	/* Software fields */
 	dma_addr_t dma_handle;
 
-	struct urb *urb;
-
 	struct list_head list;		/* P: urb->lock */
 	struct list_head remove_list;	/* P: uhci->td_remove_list_lock */
 
@@ -434,7 +432,6 @@ struct urb_priv {
 						/*  a control transfer, retrigger */
 						/*  the status phase */
 
-	unsigned long inserttime;	/* In jiffies */
 	unsigned long fsbrtime;		/* In jiffies */
 
 	struct list_head queue_list;	/* P: uhci->frame_list_lock */
diff --git a/drivers/usb/host/uhci-q.c b/drivers/usb/host/uhci-q.c
index 4e0fbe2..d540382 100644
--- a/drivers/usb/host/uhci-q.c
+++ b/drivers/usb/host/uhci-q.c
@@ -443,7 +443,6 @@ static struct urb_priv *uhci_alloc_urb_priv(struct uhci_hcd *uhci, struct urb *u
 
 	memset((void *)urbp, 0, sizeof(*urbp));
 
-	urbp->inserttime = jiffies;
 	urbp->fsbrtime = jiffies;
 	urbp->urb = urb;
 	
@@ -462,8 +461,6 @@ static void uhci_add_td_to_urb(struct urb *urb, struct uhci_td *td)
 {
 	struct urb_priv *urbp = (struct urb_priv *)urb->hcpriv;
 
-	td->urb = urb;
-
 	list_add_tail(&td->list, &urbp->td_list);
 }
 
@@ -473,8 +470,6 @@ static void uhci_remove_td_from_urb(struct uhci_td *td)
 		return;
 
 	list_del_init(&td->list);
-
-	td->urb = NULL;
 }
 
 static void uhci_destroy_urb_priv(struct uhci_hcd *uhci, struct urb *urb)
-- 
cgit v1.1


From a1d59ce842a35b552f22868404e4e7c923242257 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Fri, 16 Sep 2005 14:22:51 -0400
Subject: [PATCH] USB: UHCI: Split apart the physical and logical framelist
 arrays

This patch (as563) splits the physical and logical framelist arrays in
uhci-hcd into two separate pieces.  This will allow slightly better memory
utilization, since each piece is no larger than a single page whereas
before the whole thing was a little bigger than two pages.  It also allows
the logical array to be allocated in non-DMA-coherent memory.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/uhci-debug.c |  4 ++--
 drivers/usb/host/uhci-hcd.c   | 42 +++++++++++++++++++++++++++---------------
 drivers/usb/host/uhci-hcd.h   |  6 +++++-
 drivers/usb/host/uhci-q.c     | 20 ++++++++++----------
 4 files changed, 44 insertions(+), 28 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/uhci-debug.c b/drivers/usb/host/uhci-debug.c
index 04eddd7..151154d 100644
--- a/drivers/usb/host/uhci-debug.c
+++ b/drivers/usb/host/uhci-debug.c
@@ -445,11 +445,11 @@ static int uhci_sprint_schedule(struct uhci_hcd *uhci, char *buf, int len)
 	out += sprintf(out, "Frame List\n");
 	for (i = 0; i < UHCI_NUMFRAMES; ++i) {
 		int shown = 0;
-		td = uhci->fl->frame_cpu[i];
+		td = uhci->frame_cpu[i];
 		if (!td)
 			continue;
 
-		if (td->dma_handle != (dma_addr_t)uhci->fl->frame[i]) {
+		if (td->dma_handle != (dma_addr_t)uhci->frame[i]) {
 			show_frame_num();
 			out += sprintf(out, "    frame list does not match td->dma_handle!\n");
 		}
diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c
index 17de9ee..b44094f 100644
--- a/drivers/usb/host/uhci-hcd.c
+++ b/drivers/usb/host/uhci-hcd.c
@@ -212,7 +212,7 @@ static void configure_hc(struct uhci_hcd *uhci)
 	outb(USBSOF_DEFAULT, uhci->io_addr + USBSOF);
 
 	/* Store the frame list base address */
-	outl(uhci->fl->dma_handle, uhci->io_addr + USBFLBASEADD);
+	outl(uhci->frame_dma_handle, uhci->io_addr + USBFLBASEADD);
 
 	/* Set the current frame number */
 	outw(uhci->frame_number, uhci->io_addr + USBFRNUM);
@@ -445,8 +445,11 @@ static void release_uhci(struct uhci_hcd *uhci)
 
 	dma_pool_destroy(uhci->td_pool);
 
-	dma_free_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
-			uhci->fl, uhci->fl->dma_handle);
+	kfree(uhci->frame_cpu);
+
+	dma_free_coherent(uhci_dev(uhci),
+			UHCI_NUMFRAMES * sizeof(*uhci->frame),
+			uhci->frame, uhci->frame_dma_handle);
 
 	debugfs_remove(uhci->dentry);
 }
@@ -527,7 +530,6 @@ static int uhci_start(struct usb_hcd *hcd)
 	struct uhci_hcd *uhci = hcd_to_uhci(hcd);
 	int retval = -EBUSY;
 	int i;
-	dma_addr_t dma_handle;
 	struct dentry *dentry;
 
 	hcd->uses_new_polling = 1;
@@ -561,17 +563,23 @@ static int uhci_start(struct usb_hcd *hcd)
 
 	init_waitqueue_head(&uhci->waitqh);
 
-	uhci->fl = dma_alloc_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
-			&dma_handle, 0);
-	if (!uhci->fl) {
+	uhci->frame = dma_alloc_coherent(uhci_dev(uhci),
+			UHCI_NUMFRAMES * sizeof(*uhci->frame),
+			&uhci->frame_dma_handle, 0);
+	if (!uhci->frame) {
 		dev_err(uhci_dev(uhci), "unable to allocate "
 				"consistent memory for frame list\n");
-		goto err_alloc_fl;
+		goto err_alloc_frame;
 	}
+	memset(uhci->frame, 0, UHCI_NUMFRAMES * sizeof(*uhci->frame));
 
-	memset((void *)uhci->fl, 0, sizeof(*uhci->fl));
-
-	uhci->fl->dma_handle = dma_handle;
+	uhci->frame_cpu = kcalloc(UHCI_NUMFRAMES, sizeof(*uhci->frame_cpu),
+			GFP_KERNEL);
+	if (!uhci->frame_cpu) {
+		dev_err(uhci_dev(uhci), "unable to allocate "
+				"memory for frame pointers\n");
+		goto err_alloc_frame_cpu;
+	}
 
 	uhci->td_pool = dma_pool_create("uhci_td", uhci_dev(uhci),
 			sizeof(struct uhci_td), 16, 0);
@@ -654,7 +662,7 @@ static int uhci_start(struct usb_hcd *hcd)
 			irq = 7;
 
 		/* Only place we don't use the frame list routines */
-		uhci->fl->frame[i] = UHCI_PTR_QH |
+		uhci->frame[i] = UHCI_PTR_QH |
 				cpu_to_le32(uhci->skelqh[irq]->dma_handle);
 	}
 
@@ -686,10 +694,14 @@ err_create_qh_pool:
 	dma_pool_destroy(uhci->td_pool);
 
 err_create_td_pool:
-	dma_free_coherent(uhci_dev(uhci), sizeof(*uhci->fl),
-			uhci->fl, uhci->fl->dma_handle);
+	kfree(uhci->frame_cpu);
+
+err_alloc_frame_cpu:
+	dma_free_coherent(uhci_dev(uhci),
+			UHCI_NUMFRAMES * sizeof(*uhci->frame),
+			uhci->frame, uhci->frame_dma_handle);
 
-err_alloc_fl:
+err_alloc_frame:
 	debugfs_remove(uhci->dentry);
 
 err_create_debug_entry:
diff --git a/drivers/usb/host/uhci-hcd.h b/drivers/usb/host/uhci-hcd.h
index 1c161b4..b04d99d 100644
--- a/drivers/usb/host/uhci-hcd.h
+++ b/drivers/usb/host/uhci-hcd.h
@@ -359,7 +359,11 @@ struct uhci_hcd {
 	struct uhci_qh *skelqh[UHCI_NUM_SKELQH];	/* Skeleton QH's */
 
 	spinlock_t lock;
-	struct uhci_frame_list *fl;		/* P: uhci->lock */
+
+	dma_addr_t frame_dma_handle;		/* Hardware frame list */
+	__le32 *frame;				/* P: uhci->lock */
+	void **frame_cpu;			/* CPU's frame list */
+
 	int fsbr;				/* Full-speed bandwidth reclamation */
 	unsigned long fsbrtimeout;		/* FSBR delay */
 
diff --git a/drivers/usb/host/uhci-q.c b/drivers/usb/host/uhci-q.c
index d540382..51de06b 100644
--- a/drivers/usb/host/uhci-q.c
+++ b/drivers/usb/host/uhci-q.c
@@ -89,10 +89,10 @@ static void uhci_insert_td_frame_list(struct uhci_hcd *uhci, struct uhci_td *td,
 	td->frame = framenum;
 
 	/* Is there a TD already mapped there? */
-	if (uhci->fl->frame_cpu[framenum]) {
+	if (uhci->frame_cpu[framenum]) {
 		struct uhci_td *ftd, *ltd;
 
-		ftd = uhci->fl->frame_cpu[framenum];
+		ftd = uhci->frame_cpu[framenum];
 		ltd = list_entry(ftd->fl_list.prev, struct uhci_td, fl_list);
 
 		list_add_tail(&td->fl_list, &ftd->fl_list);
@@ -101,10 +101,10 @@ static void uhci_insert_td_frame_list(struct uhci_hcd *uhci, struct uhci_td *td,
 		wmb();
 		ltd->link = cpu_to_le32(td->dma_handle);
 	} else {
-		td->link = uhci->fl->frame[framenum];
+		td->link = uhci->frame[framenum];
 		wmb();
-		uhci->fl->frame[framenum] = cpu_to_le32(td->dma_handle);
-		uhci->fl->frame_cpu[framenum] = td;
+		uhci->frame[framenum] = cpu_to_le32(td->dma_handle);
+		uhci->frame_cpu[framenum] = td;
 	}
 }
 
@@ -114,16 +114,16 @@ static void uhci_remove_td(struct uhci_hcd *uhci, struct uhci_td *td)
 	if (td->frame == -1 && list_empty(&td->fl_list))
 		return;
 
-	if (td->frame != -1 && uhci->fl->frame_cpu[td->frame] == td) {
+	if (td->frame != -1 && uhci->frame_cpu[td->frame] == td) {
 		if (list_empty(&td->fl_list)) {
-			uhci->fl->frame[td->frame] = td->link;
-			uhci->fl->frame_cpu[td->frame] = NULL;
+			uhci->frame[td->frame] = td->link;
+			uhci->frame_cpu[td->frame] = NULL;
 		} else {
 			struct uhci_td *ntd;
 
 			ntd = list_entry(td->fl_list.next, struct uhci_td, fl_list);
-			uhci->fl->frame[td->frame] = cpu_to_le32(ntd->dma_handle);
-			uhci->fl->frame_cpu[td->frame] = ntd;
+			uhci->frame[td->frame] = cpu_to_le32(ntd->dma_handle);
+			uhci->frame_cpu[td->frame] = ntd;
 		}
 	} else {
 		struct uhci_td *ptd;
-- 
cgit v1.1


From e9b7bd4ee7f6e3ee002dc72c5211cd97c7186d00 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Thu, 22 Sep 2005 22:30:48 -0700
Subject: [PATCH] one less word in struct device

This saves a word from "struct device" ... there's a refcounting mechanism
stub that's rather ineffective (the values are never even tested!), which
can safely be deleted.  With this patch it uses normal device refcounting,
so any potential users of the pm_parent mechanism will be more correct.
(That mechanism is actually unusable for now though; it does nothing.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/base/power/main.c |   26 +++-----------------------
 include/linux/pm.h        |    1 -
 2 files changed, 3 insertions(+), 24 deletions(-)
---
 drivers/base/power/main.c | 26 +++-----------------------
 1 file changed, 3 insertions(+), 23 deletions(-)

(limited to 'drivers')

diff --git a/drivers/base/power/main.c b/drivers/base/power/main.c
index 15e6a8f..0d2e101 100644
--- a/drivers/base/power/main.c
+++ b/drivers/base/power/main.c
@@ -30,23 +30,6 @@ LIST_HEAD(dpm_off_irq);
 DECLARE_MUTEX(dpm_sem);
 DECLARE_MUTEX(dpm_list_sem);
 
-/*
- * PM Reference Counting.
- */
-
-static inline void device_pm_hold(struct device * dev)
-{
-	if (dev)
-		atomic_inc(&dev->power.pm_users);
-}
-
-static inline void device_pm_release(struct device * dev)
-{
-	if (dev)
-		atomic_dec(&dev->power.pm_users);
-}
-
-
 /**
  *	device_pm_set_parent - Specify power dependency.
  *	@dev:		Device who needs power.
@@ -62,10 +45,8 @@ static inline void device_pm_release(struct device * dev)
 
 void device_pm_set_parent(struct device * dev, struct device * parent)
 {
-	struct device * old_parent = dev->power.pm_parent;
-	device_pm_release(old_parent);
-	dev->power.pm_parent = parent;
-	device_pm_hold(parent);
+	put_device(dev->power.pm_parent);
+	dev->power.pm_parent = get_device(parent);
 }
 EXPORT_SYMBOL_GPL(device_pm_set_parent);
 
@@ -75,7 +56,6 @@ int device_pm_add(struct device * dev)
 
 	pr_debug("PM: Adding info for %s:%s\n",
 		 dev->bus ? dev->bus->name : "No Bus", dev->kobj.name);
-	atomic_set(&dev->power.pm_users, 0);
 	down(&dpm_list_sem);
 	list_add_tail(&dev->power.entry, &dpm_active);
 	device_pm_set_parent(dev, dev->parent);
@@ -91,7 +71,7 @@ void device_pm_remove(struct device * dev)
 		 dev->bus ? dev->bus->name : "No Bus", dev->kobj.name);
 	down(&dpm_list_sem);
 	dpm_sysfs_remove(dev);
-	device_pm_release(dev->power.pm_parent);
+	put_device(dev->power.pm_parent);
 	list_del_init(&dev->power.entry);
 	up(&dpm_list_sem);
 }
-- 
cgit v1.1


From 7ff71d6adf81a43505b7cbaa034e4063d3439182 Mon Sep 17 00:00:00 2001
From: Matt Porter <mporter@kernel.crashing.org>
Date: Thu, 22 Sep 2005 22:31:15 -0700
Subject: [PATCH] EHCI, split out PCI glue

This splits BIOS and PCI specific support out of ehci-hcd.c into
ehci-pci.c.  It follows the model already used in the OHCI driver
so support for non-PCI EHCI controllers can be more easily added.

Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/ehci-hcd.c |  543 ++++++--------------------------------------
 drivers/usb/host/ehci-pci.c |  414 +++++++++++++++++++++++++++++++++
 drivers/usb/host/ehci.h     |    1
 3 files changed, 492 insertions(+), 466 deletions(-)
---
 drivers/usb/host/ehci-hcd.c | 537 ++++++--------------------------------------
 drivers/usb/host/ehci-pci.c | 414 ++++++++++++++++++++++++++++++++++
 drivers/usb/host/ehci.h     |   1 +
 3 files changed, 489 insertions(+), 463 deletions(-)
 create mode 100644 drivers/usb/host/ehci-pci.c

(limited to 'drivers')

diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index 513fccb..af3c05e 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -300,44 +300,6 @@ static void ehci_watchdog (unsigned long param)
 	spin_unlock_irqrestore (&ehci->lock, flags);
 }
 
-#ifdef	CONFIG_PCI
-
-/* EHCI 0.96 (and later) section 5.1 says how to kick BIOS/SMM/...
- * off the controller (maybe it can boot from highspeed USB disks).
- */
-static int bios_handoff (struct ehci_hcd *ehci, int where, u32 cap)
-{
-	struct pci_dev *pdev = to_pci_dev(ehci_to_hcd(ehci)->self.controller);
-
-	/* always say Linux will own the hardware */
-	pci_write_config_byte(pdev, where + 3, 1);
-
-	/* maybe wait a while for BIOS to respond */
-	if (cap & (1 << 16)) {
-		int msec = 5000;
-
-		do {
-			msleep(10);
-			msec -= 10;
-			pci_read_config_dword(pdev, where, &cap);
-		} while ((cap & (1 << 16)) && msec);
-		if (cap & (1 << 16)) {
-			ehci_err(ehci, "BIOS handoff failed (%d, %08x)\n",
-				where, cap);
-			// some BIOS versions seem buggy...
-			// return 1;
-			ehci_warn (ehci, "continuing after BIOS bug...\n");
-			/* disable all SMIs, and clear "BIOS owns" flag */
-			pci_write_config_dword(pdev, where + 4, 0);
-			pci_write_config_byte(pdev, where + 2, 0);
-		} else
-			ehci_dbg(ehci, "BIOS handoff succeeded\n");
-	}
-	return 0;
-}
-
-#endif
-
 /* Reboot notifiers kick in for silicon on any bus (not just pci, etc).
  * This forcibly disables dma and IRQs, helping kexec and other cases
  * where the next system software may expect clean state.
@@ -371,156 +333,90 @@ static void ehci_port_power (struct ehci_hcd *ehci, int is_on)
 	msleep(20);
 }
 
+/*-------------------------------------------------------------------------*/
 
-/* called by khubd or root hub init threads */
+/*
+ * ehci_work is called from some interrupts, timers, and so on.
+ * it calls driver completion functions, after dropping ehci->lock.
+ */
+static void ehci_work (struct ehci_hcd *ehci, struct pt_regs *regs)
+{
+	timer_action_done (ehci, TIMER_IO_WATCHDOG);
+	if (ehci->reclaim_ready)
+		end_unlink_async (ehci, regs);
+
+	/* another CPU may drop ehci->lock during a schedule scan while
+	 * it reports urb completions.  this flag guards against bogus
+	 * attempts at re-entrant schedule scanning.
+	 */
+	if (ehci->scanning)
+		return;
+	ehci->scanning = 1;
+	scan_async (ehci, regs);
+	if (ehci->next_uframe != -1)
+		scan_periodic (ehci, regs);
+	ehci->scanning = 0;
+
+	/* the IO watchdog guards against hardware or driver bugs that
+	 * misplace IRQs, and should let us run completely without IRQs.
+	 * such lossage has been observed on both VT6202 and VT8235.
+	 */
+	if (HC_IS_RUNNING (ehci_to_hcd(ehci)->state) &&
+			(ehci->async->qh_next.ptr != NULL ||
+			 ehci->periodic_sched != 0))
+		timer_action (ehci, TIMER_IO_WATCHDOG);
+}
 
-static int ehci_hc_reset (struct usb_hcd *hcd)
+static void ehci_stop (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-	u32			temp;
-	unsigned		count = 256/4;
 
-	spin_lock_init (&ehci->lock);
+	ehci_dbg (ehci, "stop\n");
 
-	ehci->caps = hcd->regs;
-	ehci->regs = hcd->regs + HC_LENGTH (readl (&ehci->caps->hc_capbase));
-	dbg_hcs_params (ehci, "reset");
-	dbg_hcc_params (ehci, "reset");
+	/* Turn off port power on all root hub ports. */
+	ehci_port_power (ehci, 0);
 
-	/* cache this readonly data; minimize chip reads */
-	ehci->hcs_params = readl (&ehci->caps->hcs_params);
+	/* no more interrupts ... */
+	del_timer_sync (&ehci->watchdog);
 
-#ifdef	CONFIG_PCI
-	if (hcd->self.controller->bus == &pci_bus_type) {
-		struct pci_dev	*pdev = to_pci_dev(hcd->self.controller);
+	spin_lock_irq(&ehci->lock);
+	if (HC_IS_RUNNING (hcd->state))
+		ehci_quiesce (ehci);
 
-		switch (pdev->vendor) {
-		case PCI_VENDOR_ID_TDI:
-			if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
-				ehci->is_tdi_rh_tt = 1;
-				tdi_reset (ehci);
-			}
-			break;
-		case PCI_VENDOR_ID_AMD:
-			/* AMD8111 EHCI doesn't work, according to AMD errata */
-			if (pdev->device == 0x7463) {
-				ehci_info (ehci, "ignoring AMD8111 (errata)\n");
-				return -EIO;
-			}
-			break;
-		case PCI_VENDOR_ID_NVIDIA:
-			/* NVidia reports that certain chips don't handle
-			 * QH, ITD, or SITD addresses above 2GB.  (But TD,
-			 * data buffer, and periodic schedule are normal.)
-			 */
-			switch (pdev->device) {
-			case 0x003c:	/* MCP04 */
-			case 0x005b:	/* CK804 */
-			case 0x00d8:	/* CK8 */
-			case 0x00e8:	/* CK8S */
-				if (pci_set_consistent_dma_mask(pdev,
-							DMA_31BIT_MASK) < 0)
-					ehci_warn (ehci, "can't enable NVidia "
-						"workaround for >2GB RAM\n");
-				break;
-			}
-			break;
-		}
+	ehci_reset (ehci);
+	writel (0, &ehci->regs->intr_enable);
+	spin_unlock_irq(&ehci->lock);
 
-		/* optional debug port, normally in the first BAR */
-		temp = pci_find_capability (pdev, 0x0a);
-		if (temp) {
-			pci_read_config_dword(pdev, temp, &temp);
-			temp >>= 16;
-			if ((temp & (3 << 13)) == (1 << 13)) {
-				temp &= 0x1fff;
-				ehci->debug = hcd->regs + temp;
-				temp = readl (&ehci->debug->control);
-				ehci_info (ehci, "debug port %d%s\n",
-					HCS_DEBUG_PORT(ehci->hcs_params),
-					(temp & DBGP_ENABLED)
-						? " IN USE"
-						: "");
-				if (!(temp & DBGP_ENABLED))
-					ehci->debug = NULL;
-			}
-		}
+	/* let companion controllers work when we aren't */
+	writel (0, &ehci->regs->configured_flag);
+	unregister_reboot_notifier (&ehci->reboot_notifier);
 
-		temp = HCC_EXT_CAPS (readl (&ehci->caps->hcc_params));
-	} else
-		temp = 0;
-
-	/* EHCI 0.96 and later may have "extended capabilities" */
-	while (temp && count--) {
-		u32		cap;
-
-		pci_read_config_dword (to_pci_dev(hcd->self.controller),
-				temp, &cap);
-		ehci_dbg (ehci, "capability %04x at %02x\n", cap, temp);
-		switch (cap & 0xff) {
-		case 1:			/* BIOS/SMM/... handoff */
-			if (bios_handoff (ehci, temp, cap) != 0)
-				return -EOPNOTSUPP;
-			break;
-		case 0:			/* illegal reserved capability */
-			ehci_warn (ehci, "illegal capability!\n");
-			cap = 0;
-			/* FALLTHROUGH */
-		default:		/* unknown */
-			break;
-		}
-		temp = (cap >> 8) & 0xff;
-	}
-	if (!count) {
-		ehci_err (ehci, "bogus capabilities ... PCI problems!\n");
-		return -EIO;
-	}
-	if (ehci_is_TDI(ehci))
-		ehci_reset (ehci);
-#endif
+	remove_debug_files (ehci);
 
-	ehci_port_power (ehci, 0);
+	/* root hub is shut down separately (first, when possible) */
+	spin_lock_irq (&ehci->lock);
+	if (ehci->async)
+		ehci_work (ehci, NULL);
+	spin_unlock_irq (&ehci->lock);
+	ehci_mem_cleanup (ehci);
 
-	/* at least the Genesys GL880S needs fixup here */
-	temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
-	temp &= 0x0f;
-	if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
-		ehci_dbg (ehci, "bogus port configuration: "
-			"cc=%d x pcc=%d < ports=%d\n",
-			HCS_N_CC(ehci->hcs_params),
-			HCS_N_PCC(ehci->hcs_params),
-			HCS_N_PORTS(ehci->hcs_params));
-
-#ifdef	CONFIG_PCI
-		if (hcd->self.controller->bus == &pci_bus_type) {
-			struct pci_dev	*pdev;
-
-			pdev = to_pci_dev(hcd->self.controller);
-			switch (pdev->vendor) {
-			case 0x17a0:		/* GENESYS */
-				/* GL880S: should be PORTS=2 */
-				temp |= (ehci->hcs_params & ~0xf);
-				ehci->hcs_params = temp;
-				break;
-			case PCI_VENDOR_ID_NVIDIA:
-				/* NF4: should be PCC=10 */
-				break;
-			}
-		}
+#ifdef	EHCI_STATS
+	ehci_dbg (ehci, "irq normal %ld err %ld reclaim %ld (lost %ld)\n",
+		ehci->stats.normal, ehci->stats.error, ehci->stats.reclaim,
+		ehci->stats.lost_iaa);
+	ehci_dbg (ehci, "complete %ld unlink %ld\n",
+		ehci->stats.complete, ehci->stats.unlink);
 #endif
-	}
 
-	/* force HC to halt state */
-	return ehci_halt (ehci);
+	dbg_status (ehci, "ehci_stop completed", readl (&ehci->regs->status));
 }
 
-static int ehci_start (struct usb_hcd *hcd)
+static int ehci_run (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
 	u32			temp;
 	int			retval;
 	u32			hcc_params;
-	u8                      sbrn = 0;
 	int			first;
 
 	/* skip some things on restart paths */
@@ -559,27 +455,6 @@ static int ehci_start (struct usb_hcd *hcd)
 	}
 	writel (ehci->periodic_dma, &ehci->regs->frame_list);
 
-#ifdef	CONFIG_PCI
-	if (hcd->self.controller->bus == &pci_bus_type) {
-		struct pci_dev		*pdev;
-		u16			port_wake;
-
-		pdev = to_pci_dev(hcd->self.controller);
-
-		/* Serial Bus Release Number is at PCI 0x60 offset */
-		pci_read_config_byte(pdev, 0x60, &sbrn);
-
-		/* port wake capability, reported by boot firmware */
-		pci_read_config_word(pdev, 0x62, &port_wake);
-		hcd->can_wakeup = (port_wake & 1) != 0;
-
-		/* help hc dma work well with cachelines */
-		retval = pci_set_mwi(pdev);
-		if (retval)
-			ehci_dbg(ehci, "unable to enable MWI - not fatal.\n");
-	}
-#endif
-
 	/*
 	 * dedicate a qh for the async ring head, since we couldn't unlink
 	 * a 'real' qh without stopping the async schedule [4.8].  use it
@@ -675,7 +550,7 @@ static int ehci_start (struct usb_hcd *hcd)
 	temp = HC_VERSION(readl (&ehci->caps->hc_capbase));
 	ehci_info (ehci,
 		"USB %x.%x %s, EHCI %x.%02x, driver %s\n",
-		((sbrn & 0xf0)>>4), (sbrn & 0x0f),
+		((ehci->sbrn & 0xf0)>>4), (ehci->sbrn & 0x0f),
 		first ? "initialized" : "restarted",
 		temp >> 8, temp & 0xff, DRIVER_VERSION);
 
@@ -687,188 +562,6 @@ static int ehci_start (struct usb_hcd *hcd)
 	return 0;
 }
 
-/* always called by thread; normally rmmod */
-
-static void ehci_stop (struct usb_hcd *hcd)
-{
-	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-
-	ehci_dbg (ehci, "stop\n");
-
-	/* Turn off port power on all root hub ports. */
-	ehci_port_power (ehci, 0);
-
-	/* no more interrupts ... */
-	del_timer_sync (&ehci->watchdog);
-
-	spin_lock_irq(&ehci->lock);
-	if (HC_IS_RUNNING (hcd->state))
-		ehci_quiesce (ehci);
-
-	ehci_reset (ehci);
-	writel (0, &ehci->regs->intr_enable);
-	spin_unlock_irq(&ehci->lock);
-
-	/* let companion controllers work when we aren't */
-	writel (0, &ehci->regs->configured_flag);
-	unregister_reboot_notifier (&ehci->reboot_notifier);
-
-	remove_debug_files (ehci);
-
-	/* root hub is shut down separately (first, when possible) */
-	spin_lock_irq (&ehci->lock);
-	if (ehci->async)
-		ehci_work (ehci, NULL);
-	spin_unlock_irq (&ehci->lock);
-	ehci_mem_cleanup (ehci);
-
-#ifdef	EHCI_STATS
-	ehci_dbg (ehci, "irq normal %ld err %ld reclaim %ld (lost %ld)\n",
-		ehci->stats.normal, ehci->stats.error, ehci->stats.reclaim,
-		ehci->stats.lost_iaa);
-	ehci_dbg (ehci, "complete %ld unlink %ld\n",
-		ehci->stats.complete, ehci->stats.unlink);
-#endif
-
-	dbg_status (ehci, "ehci_stop completed", readl (&ehci->regs->status));
-}
-
-static int ehci_get_frame (struct usb_hcd *hcd)
-{
-	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-	return (readl (&ehci->regs->frame_index) >> 3) % ehci->periodic_size;
-}
-
-/*-------------------------------------------------------------------------*/
-
-#ifdef	CONFIG_PM
-
-/* suspend/resume, section 4.3 */
-
-/* These routines rely on the bus (pci, platform, etc)
- * to handle powerdown and wakeup, and currently also on
- * transceivers that don't need any software attention to set up
- * the right sort of wakeup.  
- */
-
-static int ehci_suspend (struct usb_hcd *hcd, pm_message_t message)
-{
-	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-
-	if (time_before (jiffies, ehci->next_statechange))
-		msleep (100);
-
-#ifdef	CONFIG_USB_SUSPEND
-	(void) usb_suspend_device (hcd->self.root_hub);
-#else
-	usb_lock_device (hcd->self.root_hub);
-	(void) ehci_hub_suspend (hcd);
-	usb_unlock_device (hcd->self.root_hub);
-#endif
-
-	// save (PCI) FLADJ in case of Vaux power loss
-	// ... we'd only use it to handle clock skew
-
-	return 0;
-}
-
-static int ehci_resume (struct usb_hcd *hcd)
-{
-	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-	unsigned		port;
-	struct usb_device	*root = hcd->self.root_hub;
-	int			retval = -EINVAL;
-
-	// maybe restore (PCI) FLADJ
-
-	if (time_before (jiffies, ehci->next_statechange))
-		msleep (100);
-
-	/* If any port is suspended (or owned by the companion),
-	 * we know we can/must resume the HC (and mustn't reset it).
-	 */
-	for (port = HCS_N_PORTS (ehci->hcs_params); port > 0; ) {
-		u32	status;
-		port--;
-		status = readl (&ehci->regs->port_status [port]);
-		if (!(status & PORT_POWER))
-			continue;
-		if (status & (PORT_SUSPEND | PORT_OWNER)) {
-			down (&hcd->self.root_hub->serialize);
-			retval = ehci_hub_resume (hcd);
-			up (&hcd->self.root_hub->serialize);
-			break;
-		}
-		if (!root->children [port])
-			continue;
-		dbg_port (ehci, __FUNCTION__, port + 1, status);
-		usb_set_device_state (root->children[port],
-					USB_STATE_NOTATTACHED);
-	}
-
-	/* Else reset, to cope with power loss or flush-to-storage
-	 * style "resume" having activated BIOS during reboot.
-	 */
-	if (port == 0) {
-		(void) ehci_halt (ehci);
-		(void) ehci_reset (ehci);
-		(void) ehci_hc_reset (hcd);
-
-		/* emptying the schedule aborts any urbs */
-		spin_lock_irq (&ehci->lock);
-		if (ehci->reclaim)
-			ehci->reclaim_ready = 1;
-		ehci_work (ehci, NULL);
-		spin_unlock_irq (&ehci->lock);
-
-		/* restart; khubd will disconnect devices */
-		retval = ehci_start (hcd);
-
-		/* here we "know" root ports should always stay powered;
-		 * but some controllers may lose all power.
-		 */
-		ehci_port_power (ehci, 1);
-	}
-
-	return retval;
-}
-
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-/*
- * ehci_work is called from some interrupts, timers, and so on.
- * it calls driver completion functions, after dropping ehci->lock.
- */
-static void ehci_work (struct ehci_hcd *ehci, struct pt_regs *regs)
-{
-	timer_action_done (ehci, TIMER_IO_WATCHDOG);
-	if (ehci->reclaim_ready)
-		end_unlink_async (ehci, regs);
-
-	/* another CPU may drop ehci->lock during a schedule scan while
-	 * it reports urb completions.  this flag guards against bogus
-	 * attempts at re-entrant schedule scanning.
-	 */
-	if (ehci->scanning)
-		return;
-	ehci->scanning = 1;
-	scan_async (ehci, regs);
-	if (ehci->next_uframe != -1)
-		scan_periodic (ehci, regs);
-	ehci->scanning = 0;
-
-	/* the IO watchdog guards against hardware or driver bugs that
-	 * misplace IRQs, and should let us run completely without IRQs.
-	 * such lossage has been observed on both VT6202 and VT8235. 
-	 */
-	if (HC_IS_RUNNING (ehci_to_hcd(ehci)->state) &&
-			(ehci->async->qh_next.ptr != NULL ||
-			 ehci->periodic_sched != 0))
-		timer_action (ehci, TIMER_IO_WATCHDOG);
-}
-
 /*-------------------------------------------------------------------------*/
 
 static irqreturn_t ehci_irq (struct usb_hcd *hcd, struct pt_regs *regs)
@@ -1179,106 +872,24 @@ done:
 	return;
 }
 
-/*-------------------------------------------------------------------------*/
-
-static const struct hc_driver ehci_driver = {
-	.description =		hcd_name,
-	.product_desc =		"EHCI Host Controller",
-	.hcd_priv_size =	sizeof(struct ehci_hcd),
-
-	/*
-	 * generic hardware linkage
-	 */
-	.irq =			ehci_irq,
-	.flags =		HCD_MEMORY | HCD_USB2,
-
-	/*
-	 * basic lifecycle operations
-	 */
-	.reset =		ehci_hc_reset,
-	.start =		ehci_start,
-#ifdef	CONFIG_PM
-	.suspend =		ehci_suspend,
-	.resume =		ehci_resume,
-#endif
-	.stop =			ehci_stop,
-
-	/*
-	 * managing i/o requests and associated device resources
-	 */
-	.urb_enqueue =		ehci_urb_enqueue,
-	.urb_dequeue =		ehci_urb_dequeue,
-	.endpoint_disable =	ehci_endpoint_disable,
-
-	/*
-	 * scheduling support
-	 */
-	.get_frame_number =	ehci_get_frame,
-
-	/*
-	 * root hub support
-	 */
-	.hub_status_data =	ehci_hub_status_data,
-	.hub_control =		ehci_hub_control,
-	.hub_suspend =		ehci_hub_suspend,
-	.hub_resume =		ehci_hub_resume,
-};
+static int ehci_get_frame (struct usb_hcd *hcd)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+	return (readl (&ehci->regs->frame_index) >> 3) % ehci->periodic_size;
+}
 
 /*-------------------------------------------------------------------------*/
 
-/* EHCI 1.0 doesn't require PCI */
-
-#ifdef	CONFIG_PCI
-
-/* PCI driver selection metadata; PCI hotplugging uses this */
-static const struct pci_device_id pci_ids [] = { {
-	/* handle any USB 2.0 EHCI controller */
-	PCI_DEVICE_CLASS(((PCI_CLASS_SERIAL_USB << 8) | 0x20), ~0),
-	.driver_data =	(unsigned long) &ehci_driver,
-	},
-	{ /* end: all zeroes */ }
-};
-MODULE_DEVICE_TABLE (pci, pci_ids);
-
-/* pci driver glue; this is a "new style" PCI driver module */
-static struct pci_driver ehci_pci_driver = {
-	.name =		(char *) hcd_name,
-	.id_table =	pci_ids,
-
-	.probe =	usb_hcd_pci_probe,
-	.remove =	usb_hcd_pci_remove,
-
-#ifdef	CONFIG_PM
-	.suspend =	usb_hcd_pci_suspend,
-	.resume =	usb_hcd_pci_resume,
-#endif
-};
-
-#endif	/* PCI */
-
-
 #define DRIVER_INFO DRIVER_VERSION " " DRIVER_DESC
 
 MODULE_DESCRIPTION (DRIVER_INFO);
 MODULE_AUTHOR (DRIVER_AUTHOR);
 MODULE_LICENSE ("GPL");
 
-static int __init init (void) 
-{
-	if (usb_disabled())
-		return -ENODEV;
-
-	pr_debug ("%s: block sizes: qh %Zd qtd %Zd itd %Zd sitd %Zd\n",
-		hcd_name,
-		sizeof (struct ehci_qh), sizeof (struct ehci_qtd),
-		sizeof (struct ehci_itd), sizeof (struct ehci_sitd));
-
-	return pci_register_driver (&ehci_pci_driver);
-}
-module_init (init);
+#ifdef CONFIG_PCI
+#include "ehci-pci.c"
+#endif
 
-static void __exit cleanup (void) 
-{	
-	pci_unregister_driver (&ehci_pci_driver);
-}
-module_exit (cleanup);
+#if !defined(CONFIG_PCI)
+#error "missing bus glue for ehci-hcd"
+#endif
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
new file mode 100644
index 0000000..66ebf75
--- /dev/null
+++ b/drivers/usb/host/ehci-pci.c
@@ -0,0 +1,414 @@
+/*
+ * EHCI HCD (Host Controller Driver) PCI Bus Glue.
+ *
+ * Copyright (c) 2000-2004 by David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
+ * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software Foundation,
+ * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef CONFIG_PCI
+#error "This file is PCI bus glue.  CONFIG_PCI must be defined."
+#endif
+
+/*-------------------------------------------------------------------------*/
+
+/* EHCI 0.96 (and later) section 5.1 says how to kick BIOS/SMM/...
+ * off the controller (maybe it can boot from highspeed USB disks).
+ */
+static int bios_handoff (struct ehci_hcd *ehci, int where, u32 cap)
+{
+	struct pci_dev *pdev = to_pci_dev(ehci_to_hcd(ehci)->self.controller);
+
+	/* always say Linux will own the hardware */
+	pci_write_config_byte(pdev, where + 3, 1);
+
+	/* maybe wait a while for BIOS to respond */
+	if (cap & (1 << 16)) {
+		int msec = 5000;
+
+		do {
+			msleep(10);
+			msec -= 10;
+			pci_read_config_dword(pdev, where, &cap);
+		} while ((cap & (1 << 16)) && msec);
+		if (cap & (1 << 16)) {
+			ehci_err(ehci, "BIOS handoff failed (%d, %08x)\n",
+				where, cap);
+			// some BIOS versions seem buggy...
+			// return 1;
+			ehci_warn (ehci, "continuing after BIOS bug...\n");
+			/* disable all SMIs, and clear "BIOS owns" flag */
+			pci_write_config_dword(pdev, where + 4, 0);
+			pci_write_config_byte(pdev, where + 2, 0);
+		} else
+			ehci_dbg(ehci, "BIOS handoff succeeded\n");
+	}
+	return 0;
+}
+
+/* called by khubd or root hub init threads */
+static int ehci_pci_reset (struct usb_hcd *hcd)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+	u32			temp;
+	unsigned		count = 256/4;
+
+	spin_lock_init (&ehci->lock);
+
+	ehci->caps = hcd->regs;
+	ehci->regs = hcd->regs + HC_LENGTH (readl (&ehci->caps->hc_capbase));
+	dbg_hcs_params (ehci, "reset");
+	dbg_hcc_params (ehci, "reset");
+
+	/* cache this readonly data; minimize chip reads */
+	ehci->hcs_params = readl (&ehci->caps->hcs_params);
+
+	if (hcd->self.controller->bus == &pci_bus_type) {
+		struct pci_dev	*pdev = to_pci_dev(hcd->self.controller);
+
+		switch (pdev->vendor) {
+		case PCI_VENDOR_ID_TDI:
+			if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
+				ehci->is_tdi_rh_tt = 1;
+				tdi_reset (ehci);
+			}
+			break;
+		case PCI_VENDOR_ID_AMD:
+			/* AMD8111 EHCI doesn't work, according to AMD errata */
+			if (pdev->device == 0x7463) {
+				ehci_info (ehci, "ignoring AMD8111 (errata)\n");
+				return -EIO;
+			}
+			break;
+		case PCI_VENDOR_ID_NVIDIA:
+			/* NVidia reports that certain chips don't handle
+			 * QH, ITD, or SITD addresses above 2GB.  (But TD,
+			 * data buffer, and periodic schedule are normal.)
+			 */
+			switch (pdev->device) {
+			case 0x003c:	/* MCP04 */
+			case 0x005b:	/* CK804 */
+			case 0x00d8:	/* CK8 */
+			case 0x00e8:	/* CK8S */
+				if (pci_set_consistent_dma_mask(pdev,
+							DMA_31BIT_MASK) < 0)
+					ehci_warn (ehci, "can't enable NVidia "
+						"workaround for >2GB RAM\n");
+				break;
+			}
+			break;
+		}
+
+		/* optional debug port, normally in the first BAR */
+		temp = pci_find_capability (pdev, 0x0a);
+		if (temp) {
+			pci_read_config_dword(pdev, temp, &temp);
+			temp >>= 16;
+			if ((temp & (3 << 13)) == (1 << 13)) {
+				temp &= 0x1fff;
+				ehci->debug = hcd->regs + temp;
+				temp = readl (&ehci->debug->control);
+				ehci_info (ehci, "debug port %d%s\n",
+					HCS_DEBUG_PORT(ehci->hcs_params),
+					(temp & DBGP_ENABLED)
+						? " IN USE"
+						: "");
+				if (!(temp & DBGP_ENABLED))
+					ehci->debug = NULL;
+			}
+		}
+
+		temp = HCC_EXT_CAPS (readl (&ehci->caps->hcc_params));
+	} else
+		temp = 0;
+
+	/* EHCI 0.96 and later may have "extended capabilities" */
+	while (temp && count--) {
+		u32		cap;
+
+		pci_read_config_dword (to_pci_dev(hcd->self.controller),
+				temp, &cap);
+		ehci_dbg (ehci, "capability %04x at %02x\n", cap, temp);
+		switch (cap & 0xff) {
+		case 1:			/* BIOS/SMM/... handoff */
+			if (bios_handoff (ehci, temp, cap) != 0)
+				return -EOPNOTSUPP;
+			break;
+		case 0:			/* illegal reserved capability */
+			ehci_warn (ehci, "illegal capability!\n");
+			cap = 0;
+			/* FALLTHROUGH */
+		default:		/* unknown */
+			break;
+		}
+		temp = (cap >> 8) & 0xff;
+	}
+	if (!count) {
+		ehci_err (ehci, "bogus capabilities ... PCI problems!\n");
+		return -EIO;
+	}
+	if (ehci_is_TDI(ehci))
+		ehci_reset (ehci);
+
+	ehci_port_power (ehci, 0);
+
+	/* at least the Genesys GL880S needs fixup here */
+	temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
+	temp &= 0x0f;
+	if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
+		ehci_dbg (ehci, "bogus port configuration: "
+			"cc=%d x pcc=%d < ports=%d\n",
+			HCS_N_CC(ehci->hcs_params),
+			HCS_N_PCC(ehci->hcs_params),
+			HCS_N_PORTS(ehci->hcs_params));
+
+		if (hcd->self.controller->bus == &pci_bus_type) {
+			struct pci_dev	*pdev;
+
+			pdev = to_pci_dev(hcd->self.controller);
+			switch (pdev->vendor) {
+			case 0x17a0:		/* GENESYS */
+				/* GL880S: should be PORTS=2 */
+				temp |= (ehci->hcs_params & ~0xf);
+				ehci->hcs_params = temp;
+				break;
+			case PCI_VENDOR_ID_NVIDIA:
+				/* NF4: should be PCC=10 */
+				break;
+			}
+		}
+	}
+
+	/* force HC to halt state */
+	return ehci_halt (ehci);
+}
+
+static int ehci_pci_start (struct usb_hcd *hcd)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+	int result = 0;
+
+	if (hcd->self.controller->bus == &pci_bus_type) {
+		struct pci_dev		*pdev;
+		u16			port_wake;
+
+		pdev = to_pci_dev(hcd->self.controller);
+
+		/* Serial Bus Release Number is at PCI 0x60 offset */
+		pci_read_config_byte(pdev, 0x60, &ehci->sbrn);
+
+		/* port wake capability, reported by boot firmware */
+		pci_read_config_word(pdev, 0x62, &port_wake);
+		hcd->can_wakeup = (port_wake & 1) != 0;
+
+		/* help hc dma work well with cachelines */
+		result = pci_set_mwi(pdev);
+		if (result)
+			ehci_dbg(ehci, "unable to enable MWI - not fatal.\n");
+	}
+
+	return ehci_run (hcd);
+}
+
+/* always called by thread; normally rmmod */
+
+static void ehci_pci_stop (struct usb_hcd *hcd)
+{
+	ehci_stop (hcd);
+}
+
+/*-------------------------------------------------------------------------*/
+
+#ifdef	CONFIG_PM
+
+/* suspend/resume, section 4.3 */
+
+/* These routines rely on the bus (pci, platform, etc)
+ * to handle powerdown and wakeup, and currently also on
+ * transceivers that don't need any software attention to set up
+ * the right sort of wakeup.
+ */
+
+static int ehci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+
+	if (time_before (jiffies, ehci->next_statechange))
+		msleep (100);
+
+#ifdef	CONFIG_USB_SUSPEND
+	(void) usb_suspend_device (hcd->self.root_hub);
+#else
+	usb_lock_device (hcd->self.root_hub);
+	(void) ehci_hub_suspend (hcd);
+	usb_unlock_device (hcd->self.root_hub);
+#endif
+
+	// save (PCI) FLADJ in case of Vaux power loss
+	// ... we'd only use it to handle clock skew
+
+	return 0;
+}
+
+static int ehci_pci_resume (struct usb_hcd *hcd)
+{
+	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
+	unsigned		port;
+	struct usb_device	*root = hcd->self.root_hub;
+	int			retval = -EINVAL;
+
+	// maybe restore (PCI) FLADJ
+
+	if (time_before (jiffies, ehci->next_statechange))
+		msleep (100);
+
+	/* If any port is suspended (or owned by the companion),
+	 * we know we can/must resume the HC (and mustn't reset it).
+	 */
+	for (port = HCS_N_PORTS (ehci->hcs_params); port > 0; ) {
+		u32	status;
+		port--;
+		status = readl (&ehci->regs->port_status [port]);
+		if (!(status & PORT_POWER))
+			continue;
+		if (status & (PORT_SUSPEND | PORT_OWNER)) {
+			down (&hcd->self.root_hub->serialize);
+			retval = ehci_hub_resume (hcd);
+			up (&hcd->self.root_hub->serialize);
+			break;
+		}
+		if (!root->children [port])
+			continue;
+		dbg_port (ehci, __FUNCTION__, port + 1, status);
+		usb_set_device_state (root->children[port],
+					USB_STATE_NOTATTACHED);
+	}
+
+	/* Else reset, to cope with power loss or flush-to-storage
+	 * style "resume" having activated BIOS during reboot.
+	 */
+	if (port == 0) {
+		(void) ehci_halt (ehci);
+		(void) ehci_reset (ehci);
+		(void) ehci_pci_reset (hcd);
+
+		/* emptying the schedule aborts any urbs */
+		spin_lock_irq (&ehci->lock);
+		if (ehci->reclaim)
+			ehci->reclaim_ready = 1;
+		ehci_work (ehci, NULL);
+		spin_unlock_irq (&ehci->lock);
+
+		/* restart; khubd will disconnect devices */
+		retval = ehci_run (hcd);
+
+		/* here we "know" root ports should always stay powered;
+		 * but some controllers may lose all power.
+		 */
+		ehci_port_power (ehci, 1);
+	}
+
+	return retval;
+}
+#endif
+
+static const struct hc_driver ehci_pci_hc_driver = {
+	.description =		hcd_name,
+	.product_desc =		"EHCI Host Controller",
+	.hcd_priv_size =	sizeof(struct ehci_hcd),
+
+	/*
+	 * generic hardware linkage
+	 */
+	.irq =			ehci_irq,
+	.flags =		HCD_MEMORY | HCD_USB2,
+
+	/*
+	 * basic lifecycle operations
+	 */
+	.reset =		ehci_pci_reset,
+	.start =		ehci_pci_start,
+#ifdef	CONFIG_PM
+	.suspend =		ehci_pci_suspend,
+	.resume =		ehci_pci_resume,
+#endif
+	.stop =			ehci_pci_stop,
+
+	/*
+	 * managing i/o requests and associated device resources
+	 */
+	.urb_enqueue =		ehci_urb_enqueue,
+	.urb_dequeue =		ehci_urb_dequeue,
+	.endpoint_disable =	ehci_endpoint_disable,
+
+	/*
+	 * scheduling support
+	 */
+	.get_frame_number =	ehci_get_frame,
+
+	/*
+	 * root hub support
+	 */
+	.hub_status_data =	ehci_hub_status_data,
+	.hub_control =		ehci_hub_control,
+	.hub_suspend =		ehci_hub_suspend,
+	.hub_resume =		ehci_hub_resume,
+};
+
+/*-------------------------------------------------------------------------*/
+
+/* PCI driver selection metadata; PCI hotplugging uses this */
+static const struct pci_device_id pci_ids [] = { {
+	/* handle any USB 2.0 EHCI controller */
+	PCI_DEVICE_CLASS(((PCI_CLASS_SERIAL_USB << 8) | 0x20), ~0),
+	.driver_data =	(unsigned long) &ehci_pci_hc_driver,
+	},
+	{ /* end: all zeroes */ }
+};
+MODULE_DEVICE_TABLE (pci, pci_ids);
+
+/* pci driver glue; this is a "new style" PCI driver module */
+static struct pci_driver ehci_pci_driver = {
+	.name =		(char *) hcd_name,
+	.id_table =	pci_ids,
+
+	.probe =	usb_hcd_pci_probe,
+	.remove =	usb_hcd_pci_remove,
+
+#ifdef	CONFIG_PM
+	.suspend =	usb_hcd_pci_suspend,
+	.resume =	usb_hcd_pci_resume,
+#endif
+};
+
+static int __init ehci_hcd_pci_init (void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	pr_debug ("%s: block sizes: qh %Zd qtd %Zd itd %Zd sitd %Zd\n",
+		hcd_name,
+		sizeof (struct ehci_qh), sizeof (struct ehci_qtd),
+		sizeof (struct ehci_itd), sizeof (struct ehci_sitd));
+
+	return pci_register_driver (&ehci_pci_driver);
+}
+module_init (ehci_hcd_pci_init);
+
+static void __exit ehci_hcd_pci_cleanup (void)
+{
+	pci_unregister_driver (&ehci_pci_driver);
+}
+module_exit (ehci_hcd_pci_cleanup);
diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h
index f34a051..18e257c 100644
--- a/drivers/usb/host/ehci.h
+++ b/drivers/usb/host/ehci.h
@@ -97,6 +97,7 @@ struct ehci_hcd {			/* one per controller */
 #else
 #	define COUNT(x) do {} while (0)
 #endif
+	u8			sbrn;		/* packed release number */
 };
 
 /* convert between an HCD pointer and the corresponding EHCI_HCD */ 
-- 
cgit v1.1


From 9293677af3dace2645dec0d0808efa02d36bf47b Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Thu, 22 Sep 2005 22:32:11 -0700
Subject: [PATCH] all HCDs provide root hub suspend/resume methods

This cleans up a small recent FIXME, ensuring that all the HCDs provide
root hub suspend/resume methods.  It also wraps the calls to those root
suspend routines just like on the PCI "USB_SUSPEND not defined" cases,
so non-PCI bus glue won't be as tempted to behave very differently.

Several of the SOC based OHCI drivers forgot to list those methods;
the patch also adds those missing declarations.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hcd.c          |   42 +++++++++++++++++++++++++---------------
 drivers/usb/host/ohci-au1xxx.c  |    5 ++++
 drivers/usb/host/ohci-lh7a404.c |    5 ++++
 drivers/usb/host/ohci-pxa27x.c  |    1
 drivers/usb/host/ohci-s3c2410.c |    1
 drivers/usb/host/ohci-sa1111.c  |    1
 6 files changed, 40 insertions(+), 15 deletions(-)
---
 drivers/usb/core/hcd.c          | 42 ++++++++++++++++++++++++++---------------
 drivers/usb/host/ohci-au1xxx.c  |  5 +++++
 drivers/usb/host/ohci-lh7a404.c |  5 +++++
 drivers/usb/host/ohci-pxa27x.c  |  1 +
 drivers/usb/host/ohci-s3c2410.c |  1 +
 drivers/usb/host/ohci-sa1111.c  |  1 +
 6 files changed, 40 insertions(+), 15 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 5e8ade0..375382f 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -1431,28 +1431,44 @@ rescan:
 
 /*-------------------------------------------------------------------------*/
 
-/* FIXME make this #ifdef CONFIG_PM ... update root hubs, retest */
-
-#ifdef	CONFIG_USB_SUSPEND
+#ifdef	CONFIG_PM
 
 static int hcd_hub_suspend (struct usb_bus *bus)
 {
 	struct usb_hcd		*hcd;
+	int			status;
 
 	hcd = container_of (bus, struct usb_hcd, self);
-	if (hcd->driver->hub_suspend)
-		return hcd->driver->hub_suspend (hcd);
-	return 0;
+	if (!hcd->driver->hub_suspend)
+		return -ENOENT;
+	hcd->state = HC_STATE_QUIESCING;
+	status = hcd->driver->hub_suspend (hcd);
+	if (status == 0)
+		hcd->state = HC_STATE_SUSPENDED;
+	else
+		dev_dbg(&bus->root_hub->dev, "%s fail, err %d\n",
+				"suspend", status);
+	return status;
 }
 
 static int hcd_hub_resume (struct usb_bus *bus)
 {
 	struct usb_hcd		*hcd;
+	int			status;
 
 	hcd = container_of (bus, struct usb_hcd, self);
-	if (hcd->driver->hub_resume)
-		return hcd->driver->hub_resume (hcd);
-	return 0;
+	if (!hcd->driver->hub_resume)
+		return -ENOENT;
+	hcd->state = HC_STATE_RESUMING;
+	status = hcd->driver->hub_resume (hcd);
+	if (status == 0)
+		hcd->state = HC_STATE_RUNNING;
+	else {
+		dev_dbg(&bus->root_hub->dev, "%s fail, err %d\n",
+				"resume", status);
+		usb_hc_died(hcd);
+	}
+	return status;
 }
 
 /**
@@ -1473,13 +1489,9 @@ void usb_hcd_resume_root_hub (struct usb_hcd *hcd)
 		usb_resume_root_hub (hcd->self.root_hub);
 	spin_unlock_irqrestore (&hcd_root_hub_lock, flags);
 }
+EXPORT_SYMBOL_GPL(usb_hcd_resume_root_hub);
 
-#else
-void usb_hcd_resume_root_hub (struct usb_hcd *hcd)
-{
-}
 #endif
-EXPORT_SYMBOL_GPL(usb_hcd_resume_root_hub);
 
 /*-------------------------------------------------------------------------*/
 
@@ -1532,7 +1544,7 @@ static struct usb_operations usb_hcd_operations = {
 	.buffer_alloc =		hcd_buffer_alloc,
 	.buffer_free =		hcd_buffer_free,
 	.disable =		hcd_endpoint_disable,
-#ifdef	CONFIG_USB_SUSPEND
+#ifdef	CONFIG_PM
 	.hub_suspend =		hcd_hub_suspend,
 	.hub_resume =		hcd_hub_resume,
 #endif
diff --git a/drivers/usb/host/ohci-au1xxx.c b/drivers/usb/host/ohci-au1xxx.c
index 3981bf1..550d67a 100644
--- a/drivers/usb/host/ohci-au1xxx.c
+++ b/drivers/usb/host/ohci-au1xxx.c
@@ -214,6 +214,11 @@ static const struct hc_driver ohci_au1xxx_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
+#ifdef	CONFIG_PM
+	.hub_suspend =		ohci_hub_suspend,
+	.hub_resume =		ohci_hub_resume,
+#endif
+	.start_port_reset =	ohci_start_port_reset,
 };
 
 /*-------------------------------------------------------------------------*/
diff --git a/drivers/usb/host/ohci-lh7a404.c b/drivers/usb/host/ohci-lh7a404.c
index 859aca7b..71d975a 100644
--- a/drivers/usb/host/ohci-lh7a404.c
+++ b/drivers/usb/host/ohci-lh7a404.c
@@ -193,6 +193,11 @@ static const struct hc_driver ohci_lh7a404_hc_driver = {
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
+#ifdef	CONFIG_PM
+	.hub_suspend =		ohci_hub_suspend,
+	.hub_resume =		ohci_hub_resume,
+#endif
+	.start_port_reset =	ohci_start_port_reset,
 };
 
 /*-------------------------------------------------------------------------*/
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index 986c4f6..2e7b485 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -282,6 +282,7 @@ static const struct hc_driver ohci_pxa27x_hc_driver = {
 	.hub_suspend =		ohci_hub_suspend,
 	.hub_resume =		ohci_hub_resume,
 #endif
+	.start_port_reset =	ohci_start_port_reset,
 };
 
 /*-------------------------------------------------------------------------*/
diff --git a/drivers/usb/host/ohci-s3c2410.c b/drivers/usb/host/ohci-s3c2410.c
index 8cf12b2..922e2a6 100644
--- a/drivers/usb/host/ohci-s3c2410.c
+++ b/drivers/usb/host/ohci-s3c2410.c
@@ -452,6 +452,7 @@ static const struct hc_driver ohci_s3c2410_hc_driver = {
 	.hub_suspend =		ohci_hub_suspend,
 	.hub_resume =		ohci_hub_resume,
 #endif
+	.start_port_reset =	ohci_start_port_reset,
 };
 
 /* device driver */
diff --git a/drivers/usb/host/ohci-sa1111.c b/drivers/usb/host/ohci-sa1111.c
index 7dd1f41..13324b7 100644
--- a/drivers/usb/host/ohci-sa1111.c
+++ b/drivers/usb/host/ohci-sa1111.c
@@ -239,6 +239,7 @@ static const struct hc_driver ohci_sa1111_hc_driver = {
 	.hub_suspend =		ohci_hub_suspend,
 	.hub_resume =		ohci_hub_resume,
 #endif
+	.start_port_reset =	ohci_start_port_reset,
 };
 
 /*-------------------------------------------------------------------------*/
-- 
cgit v1.1


From 979d5199fee9e80290ddeb532e5993bd15506712 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Thu, 22 Sep 2005 22:32:24 -0700
Subject: [PATCH] root hub changes (lesser half)

This patch collects various small updates related to root hubs, to shrink
later patches which build on them.

  - For root hub suspend/resume support:
     * Make the existing usb_hcd_resume_root_hub() routine respect pmcore
       locking, exporting and using the dpm_runtime_resume() method.
     * Add a new usb_hcd_suspend_root_hub() to pair with that routine.
       (Essential to make OHCI autosuspend behave again...)
     * HC_SUSPENDED by itself only refers to the root hub's downstream ports.
       So let HCDs see root hub URBs unless the parent device is suspended.

  - Remove an assertion we no longer need (and now, also don't want).

  - Generic suspend/resume updates to work better with swsusp.
     * Ignore the FREEZE vs SUSPEND distinction for hardware; trying to
       use it breaks the swsusp snapshots it's supposed to help (sigh).
     * On resume, mark devices as resumed right away, but then
       do nothing else if the device is marked NOTATTACHED.

These changes shouldn't be very noticable by themselves.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/base/power/runtime.c |    1
 drivers/usb/core/hcd.c       |   64 ++++++++++++++++++++++++++++++++++++++-----
 drivers/usb/core/hcd.h       |    1
 drivers/usb/core/hub.c       |   45 ++++++++++++++++++++++++------
 drivers/usb/core/usb.c       |   20 +++++++++----
 drivers/usb/core/usb.h       |    1
 6 files changed, 111 insertions(+), 21 deletions(-)
---
 drivers/base/power/runtime.c |  1 +
 drivers/usb/core/hcd.c       | 64 +++++++++++++++++++++++++++++++++++++++-----
 drivers/usb/core/hcd.h       |  1 +
 drivers/usb/core/hub.c       | 45 +++++++++++++++++++++++++------
 drivers/usb/core/usb.c       | 20 +++++++++-----
 drivers/usb/core/usb.h       |  1 +
 6 files changed, 111 insertions(+), 21 deletions(-)

(limited to 'drivers')

diff --git a/drivers/base/power/runtime.c b/drivers/base/power/runtime.c
index e8f0519..adbc3148 100644
--- a/drivers/base/power/runtime.c
+++ b/drivers/base/power/runtime.c
@@ -36,6 +36,7 @@ void dpm_runtime_resume(struct device * dev)
 	runtime_resume(dev);
 	up(&dpm_sem);
 }
+EXPORT_SYMBOL(dpm_runtime_resume);
 
 
 /**
diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 375382f..de59bb5 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -1143,10 +1143,20 @@ static int hcd_submit_urb (struct urb *urb, gfp_t mem_flags)
 	else switch (hcd->state) {
 	case HC_STATE_RUNNING:
 	case HC_STATE_RESUMING:
+doit:
 		usb_get_dev (urb->dev);
 		list_add_tail (&urb->urb_list, &ep->urb_list);
 		status = 0;
 		break;
+	case HC_STATE_SUSPENDED:
+		/* HC upstream links (register access, wakeup signaling) can work
+		 * even when the downstream links (and DMA etc) are quiesced; let
+		 * usbcore talk to the root hub.
+		 */
+		if (hcd->self.controller->power.power_state.event == PM_EVENT_ON
+				&& urb->dev->parent == NULL)
+			goto doit;
+		/* FALL THROUGH */
 	default:
 		status = -ESHUTDOWN;
 		break;
@@ -1294,12 +1304,6 @@ static int hcd_unlink_urb (struct urb *urb, int status)
 		goto done;
 	}
 
-	/* running ~= hc unlink handshake works (irq, timer, etc)
-	 * halted ~= no unlink handshake is needed
-	 * suspended, resuming == should never happen
-	 */
-	WARN_ON (!HC_IS_RUNNING (hcd->state) && hcd->state != HC_STATE_HALT);
-
 	/* insist the urb is still queued */
 	list_for_each(tmp, &ep->urb_list) {
 		if (tmp == &urb->urb_list)
@@ -1459,6 +1463,8 @@ static int hcd_hub_resume (struct usb_bus *bus)
 	hcd = container_of (bus, struct usb_hcd, self);
 	if (!hcd->driver->hub_resume)
 		return -ENOENT;
+	if (hcd->state == HC_STATE_RUNNING)
+		return 0;
 	hcd->state = HC_STATE_RESUMING;
 	status = hcd->driver->hub_resume (hcd);
 	if (status == 0)
@@ -1471,6 +1477,50 @@ static int hcd_hub_resume (struct usb_bus *bus)
 	return status;
 }
 
+/*
+ * usb_hcd_suspend_root_hub - HCD autosuspends downstream ports
+ * @hcd: host controller for this root hub
+ *
+ * This call arranges that usb_hcd_resume_root_hub() is safe to call later;
+ * that the HCD's root hub polling is deactivated; and that the root's hub
+ * driver is suspended.  HCDs may call this to autosuspend when their root
+ * hub's downstream ports are all inactive:  unpowered, disconnected,
+ * disabled, or suspended.
+ *
+ * The HCD will autoresume on device connect change detection (using SRP
+ * or a D+/D- pullup).  The HCD also autoresumes on remote wakeup signaling
+ * from any ports that are suspended (if that is enabled).  In most cases,
+ * overcurrent signaling (on powered ports) will also start autoresume.
+ *
+ * Always called with IRQs blocked.
+ */
+void usb_hcd_suspend_root_hub (struct usb_hcd *hcd)
+{
+	struct urb	*urb;
+
+	spin_lock (&hcd_root_hub_lock);
+	usb_suspend_root_hub (hcd->self.root_hub);
+
+	/* force status urb to complete/unlink while suspended */
+	if (hcd->status_urb) {
+		urb = hcd->status_urb;
+		urb->status = -ECONNRESET;
+		urb->hcpriv = NULL;
+		urb->actual_length = 0;
+
+		del_timer (&hcd->rh_timer);
+		hcd->poll_pending = 0;
+		hcd->status_urb = NULL;
+	} else
+		urb = NULL;
+	spin_unlock (&hcd_root_hub_lock);
+	hcd->state = HC_STATE_SUSPENDED;
+
+	if (urb)
+		usb_hcd_giveback_urb (hcd, urb, NULL);
+}
+EXPORT_SYMBOL_GPL(usb_hcd_suspend_root_hub);
+
 /**
  * usb_hcd_resume_root_hub - called by HCD to resume its root hub 
  * @hcd: host controller for this root hub
@@ -1478,7 +1528,7 @@ static int hcd_hub_resume (struct usb_bus *bus)
  * The USB host controller calls this function when its root hub is
  * suspended (with the remote wakeup feature enabled) and a remote
  * wakeup request is received.  It queues a request for khubd to
- * resume the root hub.
+ * resume the root hub (that is, manage its downstream ports again).
  */
 void usb_hcd_resume_root_hub (struct usb_hcd *hcd)
 {
diff --git a/drivers/usb/core/hcd.h b/drivers/usb/core/hcd.h
index 1f1ed62..eb21f13 100644
--- a/drivers/usb/core/hcd.h
+++ b/drivers/usb/core/hcd.h
@@ -355,6 +355,7 @@ extern long usb_calc_bus_time (int speed, int is_input,
 
 extern struct usb_bus *usb_alloc_bus (struct usb_operations *);
 
+extern void usb_hcd_suspend_root_hub (struct usb_hcd *hcd);
 extern void usb_hcd_resume_root_hub (struct usb_hcd *hcd);
 
 extern void usb_set_device_state(struct usb_device *udev,
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 6600644..3c8d8d1 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -449,11 +449,18 @@ static void hub_power_on(struct usb_hub *hub)
 	msleep(max(pgood_delay, (unsigned) 100));
 }
 
-static void hub_quiesce(struct usb_hub *hub)
+static inline void __hub_quiesce(struct usb_hub *hub)
 {
-	/* stop khubd and related activity */
+	/* (nonblocking) khubd and related activity won't re-trigger */
 	hub->quiescing = 1;
 	hub->activating = 0;
+	hub->resume_root_hub = 0;
+}
+
+static void hub_quiesce(struct usb_hub *hub)
+{
+	/* (blocking) stop khubd and related activity */
+	__hub_quiesce(hub);
 	usb_kill_urb(hub->urb);
 	if (hub->has_indicators)
 		cancel_delayed_work(&hub->leds);
@@ -467,6 +474,7 @@ static void hub_activate(struct usb_hub *hub)
 
 	hub->quiescing = 0;
 	hub->activating = 1;
+	hub->resume_root_hub = 0;
 	status = usb_submit_urb(hub->urb, GFP_NOIO);
 	if (status < 0)
 		dev_err(hub->intfdev, "activate --> %d\n", status);
@@ -1959,6 +1967,18 @@ static int hub_resume(struct usb_interface *intf)
 	return 0;
 }
 
+void usb_suspend_root_hub(struct usb_device *hdev)
+{
+	struct usb_hub *hub = hdev_to_hub(hdev);
+
+	/* This also makes any led blinker stop retriggering.  We're called
+	 * from irq, so the blinker might still be scheduled.  Caller promises
+	 * that the root hub status URB will be canceled.
+	 */
+	__hub_quiesce(hub);
+	mark_quiesced(to_usb_interface(hub->intfdev));
+}
+
 void usb_resume_root_hub(struct usb_device *hdev)
 {
 	struct usb_hub *hub = hdev_to_hub(hdev);
@@ -2616,21 +2636,30 @@ static void hub_events(void)
 		intf = to_usb_interface(hub->intfdev);
 		hub_dev = &intf->dev;
 
-		dev_dbg(hub_dev, "state %d ports %d chg %04x evt %04x\n",
+		i = hub->resume_root_hub;
+
+		dev_dbg(hub_dev, "state %d ports %d chg %04x evt %04x%s\n",
 				hdev->state, hub->descriptor
 					? hub->descriptor->bNbrPorts
 					: 0,
 				/* NOTE: expects max 15 ports... */
 				(u16) hub->change_bits[0],
-				(u16) hub->event_bits[0]);
+				(u16) hub->event_bits[0],
+				i ? ", resume root" : "");
 
 		usb_get_intf(intf);
-		i = hub->resume_root_hub;
 		spin_unlock_irq(&hub_event_lock);
 
-		/* Is this is a root hub wanting to be resumed? */
-		if (i)
-			usb_resume_device(hdev);
+		/* Is this is a root hub wanting to reactivate the downstream
+		 * ports?  If so, be sure the interface resumes even if its
+		 * stub "device" node was never suspended.
+		 */
+		if (i) {
+			extern void dpm_runtime_resume(struct device *);
+
+			dpm_runtime_resume(&hdev->dev);
+			dpm_runtime_resume(&intf->dev);
+		}
 
 		/* Lock the device, then check to see if we were
 		 * disconnected while waiting for the lock to succeed. */
diff --git a/drivers/usb/core/usb.c b/drivers/usb/core/usb.c
index e89dbd4..2493e7d 100644
--- a/drivers/usb/core/usb.c
+++ b/drivers/usb/core/usb.c
@@ -1427,6 +1427,7 @@ static int usb_generic_suspend(struct device *dev, pm_message_t message)
 
 	/* USB devices enter SUSPEND state through their hubs, but can be
 	 * marked for FREEZE as soon as their children are already idled.
+	 * But those semantics are useless, so we equate the two (sigh).
 	 */
 	if (dev->driver == &usb_generic_driver) {
 		if (dev->power.power_state.event == message.event)
@@ -1435,10 +1436,6 @@ static int usb_generic_suspend(struct device *dev, pm_message_t message)
 		status = device_for_each_child(dev, NULL, verify_suspended);
 		if (status)
 			return status;
-		if (message.event == PM_EVENT_FREEZE) {
-			dev->power.power_state = message;
-			return 0;
-		}
  		return usb_suspend_device (to_usb_device(dev));
 	}
 
@@ -1471,14 +1468,22 @@ static int usb_generic_resume(struct device *dev)
 {
 	struct usb_interface	*intf;
 	struct usb_driver	*driver;
+	struct usb_device	*udev;
 	int			status;
 
 	if (dev->power.power_state.event == PM_EVENT_ON)
 		return 0;
 
+	/* mark things as "on" immediately, no matter what errors crop up */
+	dev->power.power_state.event = PM_EVENT_ON;
+
 	/* devices resume through their hubs */
-	if (dev->driver == &usb_generic_driver)
+	if (dev->driver == &usb_generic_driver) {
+		udev = to_usb_device(dev);
+		if (udev->state == USB_STATE_NOTATTACHED)
+			return 0;
 		return usb_resume_device (to_usb_device(dev));
+	}
 
 	if ((dev->driver == NULL) ||
 	    (dev->driver_data == &usb_generic_driver_data))
@@ -1487,11 +1492,14 @@ static int usb_generic_resume(struct device *dev)
 	intf = to_usb_interface(dev);
 	driver = to_usb_driver(dev->driver);
 
+	udev = interface_to_usbdev(intf);
+	if (udev->state == USB_STATE_NOTATTACHED)
+		return 0;
+
 	/* if driver was suspended, it has a resume method;
 	 * however, sysfs can wrongly mark things as suspended
 	 * (on the "no suspend method" FIXME path above)
 	 */
-	mark_active(intf);
 	if (driver->resume) {
 		status = driver->resume(intf);
 		if (status) {
diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
index 3741a99..7add46e 100644
--- a/drivers/usb/core/usb.h
+++ b/drivers/usb/core/usb.h
@@ -19,6 +19,7 @@ extern void usb_lock_all_devices(void);
 extern void usb_unlock_all_devices(void);
 
 extern void usb_kick_khubd(struct usb_device *dev);
+extern void usb_suspend_root_hub(struct usb_device *hdev);
 extern void usb_resume_root_hub(struct usb_device *dev);
 
 extern int  usb_hub_init(void);
-- 
cgit v1.1


From f3f3253d644d36a2ea5464005a9c2cf28804d200 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Thu, 22 Sep 2005 22:37:29 -0700
Subject: [PATCH] root hub updates (greater half)

This patch associates hub suspend and resume logic (including for root hubs)
with CONFIG_PM -- instead of CONFIG_USB_SUSPEND as before -- thereby unifying
two troublesome versions of suspend logic into just one.  It'll be easier to
keep things right from now on.

  - Now usbcore _always_ calls hcd->hub_suspend as needed, instead of
    only when USB_SUSPEND is enabled:
     * Those root hub methods are now called from hub suspend/resume;
       no more skipping between layers during device suspend/resume;
     * It now handles cases allowed by sysfs or autosuspended root hubs,
       by forcing the hub interface to resume too.

  - All devices, including virtual root hubs, now get the same treatment
    on their resume paths ... including re-activating all their interfaces.

Plus it gets rid of those stub copies of usb_{suspend,resume}_device(), and
updates the Kconfig to match the new definition of USB_SUSPEND:  it provides
(a) selective suspend, downstream from hubs; and (b) remote wakeup, upstream
from any device configuration which supports it.

This calls for minor followup patches for most HCDs (and their PCI glue).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/Kconfig |   11 ++-
 drivers/usb/core/hub.c   |  163 +++++++++++++++++++++++++----------------------
 2 files changed, 97 insertions(+), 77 deletions(-)
---
 drivers/usb/core/Kconfig |  11 ++--
 drivers/usb/core/hub.c   | 163 ++++++++++++++++++++++++++---------------------
 2 files changed, 97 insertions(+), 77 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/Kconfig b/drivers/usb/core/Kconfig
index 1a9ff61..ff03184 100644
--- a/drivers/usb/core/Kconfig
+++ b/drivers/usb/core/Kconfig
@@ -61,14 +61,17 @@ config USB_DYNAMIC_MINORS
 	  If you are unsure about this, say N here.
 
 config USB_SUSPEND
-	bool "USB suspend/resume (EXPERIMENTAL)"
+	bool "USB selective suspend/resume and wakeup (EXPERIMENTAL)"
 	depends on USB && PM && EXPERIMENTAL
 	help
 	  If you say Y here, you can use driver calls or the sysfs
 	  "power/state" file to suspend or resume individual USB
-	  peripherals.  There are many related features, such as
-	  remote wakeup and driver-specific suspend processing, that
-	  may not yet work as expected.
+	  peripherals.
+
+	  Also, USB "remote wakeup" signaling is supported, whereby some
+	  USB devices (like keyboards and network adapters) can wake up
+	  their parent hub.  That wakeup cascades up the USB tree, and
+	  could wake the system from states like suspend-to-RAM.
 
 	  If you are unsure about this, say N here.
 
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 3c8d8d1..6a601a4 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1612,7 +1612,7 @@ static int hub_port_suspend(struct usb_hub *hub, int port1,
  */
 static int __usb_suspend_device (struct usb_device *udev, int port1)
 {
-	int	status;
+	int	status = 0;
 
 	/* caller owns the udev device lock */
 	if (port1 < 0)
@@ -1638,21 +1638,10 @@ static int __usb_suspend_device (struct usb_device *udev, int port1)
 		}
 	}
 
-	/* "global suspend" of the HC-to-USB interface (root hub), or
-	 * "selective suspend" of just one hub-device link.
+	/* we only change a device's upstream USB link.
+	 * root hubs have no upstream USB link.
 	 */
-	if (!udev->parent) {
-		struct usb_bus	*bus = udev->bus;
-		if (bus && bus->op->hub_suspend) {
-			status = bus->op->hub_suspend (bus);
-			if (status == 0) {
-				dev_dbg(&udev->dev, "usb suspend\n");
-				usb_set_device_state(udev,
-						USB_STATE_SUSPENDED);
-			}
-		} else
-			status = -EOPNOTSUPP;
-	} else
+	if (udev->parent)
 		status = hub_port_suspend(hdev_to_hub(udev->parent), port1,
 				udev);
 
@@ -1661,6 +1650,8 @@ static int __usb_suspend_device (struct usb_device *udev, int port1)
 	return status;
 }
 
+#endif
+
 /**
  * usb_suspend_device - suspend a usb device
  * @udev: device that's no longer in active use
@@ -1683,6 +1674,7 @@ static int __usb_suspend_device (struct usb_device *udev, int port1)
  */
 int usb_suspend_device(struct usb_device *udev)
 {
+#ifdef	CONFIG_USB_SUSPEND
 	int	port1, status;
 
 	port1 = locktree(udev);
@@ -1692,8 +1684,14 @@ int usb_suspend_device(struct usb_device *udev)
 	status = __usb_suspend_device(udev, port1);
 	usb_unlock_device(udev);
 	return status;
+#else
+	/* NOTE:  udev->state unchanged, it's not lying ... */
+	udev->dev.power.power_state = PMSG_SUSPEND;
+	return 0;
+#endif
 }
 
+
 /*
  * If the USB "suspend" state is in use (rather than "global suspend"),
  * many devices will be individually taken out of suspend state using
@@ -1702,13 +1700,13 @@ int usb_suspend_device(struct usb_device *udev)
  * resume (by host) or remote wakeup (by device) ... now see what changed
  * in the tree that's rooted at this device.
  */
-static int finish_port_resume(struct usb_device *udev)
+static int finish_device_resume(struct usb_device *udev)
 {
 	int	status;
 	u16	devstatus;
 
 	/* caller owns the udev device lock */
-	dev_dbg(&udev->dev, "usb resume\n");
+	dev_dbg(&udev->dev, "finish resume\n");
 
 	/* usb ch9 identifies four variants of SUSPENDED, based on what
 	 * state the device resumes to.  Linux currently won't see the
@@ -1718,7 +1716,6 @@ static int finish_port_resume(struct usb_device *udev)
 	usb_set_device_state(udev, udev->actconfig
 			? USB_STATE_CONFIGURED
 			: USB_STATE_ADDRESS);
-	udev->dev.power.power_state = PMSG_ON;
 
  	/* 10.5.4.5 says be sure devices in the tree are still there.
  	 * For now let's assume the device didn't go crazy on resume,
@@ -1734,7 +1731,8 @@ static int finish_port_resume(struct usb_device *udev)
 		int		(*resume)(struct device *);
 
 		le16_to_cpus(&devstatus);
-		if (devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)) {
+		if (devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)
+				&& udev->parent) {
 			status = usb_control_msg(udev,
 					usb_sndctrlpipe(udev, 0),
 					USB_REQ_CLEAR_FEATURE,
@@ -1764,6 +1762,8 @@ static int finish_port_resume(struct usb_device *udev)
 	return status;
 }
 
+#ifdef	CONFIG_USB_SUSPEND
+
 static int
 hub_port_resume(struct usb_hub *hub, int port1, struct usb_device *udev)
 {
@@ -1809,7 +1809,7 @@ hub_port_resume(struct usb_hub *hub, int port1, struct usb_device *udev)
 			/* TRSMRCY = 10 msec */
 			msleep(10);
 			if (udev)
-				status = finish_port_resume(udev);
+				status = finish_device_resume(udev);
 		}
 	}
 	if (status < 0)
@@ -1818,7 +1818,7 @@ hub_port_resume(struct usb_hub *hub, int port1, struct usb_device *udev)
 	return status;
 }
 
-static int hub_resume (struct usb_interface *intf);
+#endif
 
 /**
  * usb_resume_device - re-activate a suspended usb device
@@ -1841,35 +1841,22 @@ int usb_resume_device(struct usb_device *udev)
 	if (port1 < 0)
 		return port1;
 
-	/* "global resume" of the HC-to-USB interface (root hub), or
-	 * selective resume of one hub-to-device port
-	 */
-	if (!udev->parent) {
-		struct usb_bus	*bus = udev->bus;
-		if (bus && bus->op->hub_resume) {
-			status = bus->op->hub_resume (bus);
+#ifdef	CONFIG_USB_SUSPEND
+	/* selective resume of one downstream hub-to-device port */
+	if (udev->parent) {
+		if (udev->state == USB_STATE_SUSPENDED) {
+			// NOTE swsusp may bork us, device state being wrong...
+			// NOTE this fails if parent is also suspended...
+			status = hub_port_resume(hdev_to_hub(udev->parent),
+					port1, udev);
 		} else
-			status = -EOPNOTSUPP;
-		if (status == 0) {
-			dev_dbg(&udev->dev, "usb resume\n");
-			/* TRSMRCY = 10 msec */
-			msleep(10);
-			usb_set_device_state (udev, USB_STATE_CONFIGURED);
-			udev->dev.power.power_state = PMSG_ON;
-			status = hub_resume (udev
-					->actconfig->interface[0]);
-		}
-	} else if (udev->state == USB_STATE_SUSPENDED) {
-		// NOTE this fails if parent is also suspended...
-		status = hub_port_resume(hdev_to_hub(udev->parent),
-				port1, udev);
-	} else {
-		status = 0;
-	}
-	if (status < 0) {
+			status = 0;
+	} else
+#endif
+		status = finish_device_resume(udev);
+	if (status < 0)
 		dev_dbg(&udev->dev, "can't resume, status %d\n",
 			status);
-	}
 
 	usb_unlock_device(udev);
 
@@ -1886,6 +1873,8 @@ static int remote_wakeup(struct usb_device *udev)
 {
 	int	status = 0;
 
+#ifdef	CONFIG_USB_SUSPEND
+
 	/* don't repeat RESUME sequence if this device
 	 * was already woken up by some other task
 	 */
@@ -1894,9 +1883,10 @@ static int remote_wakeup(struct usb_device *udev)
 		dev_dbg(&udev->dev, "RESUME (wakeup)\n");
 		/* TRSMRCY = 10 msec */
 		msleep(10);
-		status = finish_port_resume(udev);
+		status = finish_device_resume(udev);
 	}
 	up(&udev->serialize);
+#endif
 	return status;
 }
 
@@ -1911,12 +1901,32 @@ static int hub_suspend(struct usb_interface *intf, pm_message_t msg)
 		struct usb_device	*udev;
 
 		udev = hdev->children [port1-1];
-		if (udev && udev->state != USB_STATE_SUSPENDED) {
+		if (udev && (udev->dev.power.power_state.event
+					== PM_EVENT_ON
+#ifdef	CONFIG_USB_SUSPEND
+				|| udev->state != USB_STATE_SUSPENDED
+#endif
+				)) {
 			dev_dbg(&intf->dev, "port %d nyet suspended\n", port1);
 			return -EBUSY;
 		}
 	}
 
+	/* "global suspend" of the downstream HC-to-USB interface */
+	if (!hdev->parent) {
+		struct usb_bus	*bus = hdev->bus;
+		if (bus && bus->op->hub_suspend) {
+			int	status = bus->op->hub_suspend (bus);
+
+			if (status != 0) {
+				dev_dbg(&hdev->dev, "'global' suspend %d\n",
+					status);
+				return status;
+			}
+		} else
+			return -EOPNOTSUPP;
+	}
+
 	/* stop khubd and related activity */
 	hub_quiesce(hub);
 	return 0;
@@ -1926,9 +1936,36 @@ static int hub_resume(struct usb_interface *intf)
 {
 	struct usb_device	*hdev = interface_to_usbdev(intf);
 	struct usb_hub		*hub = usb_get_intfdata (intf);
-	unsigned		port1;
 	int			status;
 
+	/* "global resume" of the downstream HC-to-USB interface */
+	if (!hdev->parent) {
+		struct usb_bus	*bus = hdev->bus;
+		if (bus && bus->op->hub_resume) {
+			status = bus->op->hub_resume (bus);
+			if (status) {
+				dev_dbg(&intf->dev, "'global' resume %d\n",
+					status);
+				return status;
+			}
+		} else
+			return -EOPNOTSUPP;
+		if (status == 0) {
+			/* TRSMRCY = 10 msec */
+			msleep(10);
+		}
+	}
+
+	hub_activate(hub);
+
+	/* REVISIT:  this recursion probably shouldn't exist.  Remove
+	 * this code sometime, after retesting with different root and
+	 * external hubs.
+	 */
+#ifdef	CONFIG_USB_SUSPEND
+	{
+	unsigned		port1;
+
 	for (port1 = 1; port1 <= hdev->maxchild; port1++) {
 		struct usb_device	*udev;
 		u16			portstat, portchange;
@@ -1953,7 +1990,7 @@ static int hub_resume(struct usb_interface *intf)
 		if (portstat & USB_PORT_STAT_SUSPEND)
 			status = hub_port_resume(hub, port1, udev);
 		else {
-			status = finish_port_resume(udev);
+			status = finish_device_resume(udev);
 			if (status < 0) {
 				dev_dbg(&intf->dev, "resume port %d --> %d\n",
 					port1, status);
@@ -1962,8 +1999,8 @@ static int hub_resume(struct usb_interface *intf)
 		}
 		up(&udev->serialize);
 	}
-	hub->resume_root_hub = 0;
-	hub_activate(hub);
+	}
+#endif
 	return 0;
 }
 
@@ -1987,26 +2024,6 @@ void usb_resume_root_hub(struct usb_device *hdev)
 	kick_khubd(hub);
 }
 
-#else	/* !CONFIG_USB_SUSPEND */
-
-int usb_suspend_device(struct usb_device *udev)
-{
-	/* state does NOT lie by saying it's USB_STATE_SUSPENDED! */
-	return 0;
-}
-
-int usb_resume_device(struct usb_device *udev)
-{
-	udev->dev.power.power_state.event = PM_EVENT_ON;
-	return 0;
-}
-
-#define	hub_suspend		NULL
-#define	hub_resume		NULL
-#define	remote_wakeup(x)	0
-
-#endif	/* CONFIG_USB_SUSPEND */
-
 EXPORT_SYMBOL(usb_suspend_device);
 EXPORT_SYMBOL(usb_resume_device);
 
-- 
cgit v1.1


From 5f827ea3c3820cd8e0a1a35e4d275c8b78ee94e1 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Thu, 22 Sep 2005 22:38:16 -0700
Subject: [PATCH] usbcore PCI glue updates for PM

This updates the PCI glue to address the new and simplified usbcore suspend
semantics, where CONFIG_USB_SUSPEND becomes irrelevant to HCDs because
hcd->hub_suspend() will always be called.

  - Removes now-unneeded recursion support

  - Go back to ignoring faults reported by the wakeup calls; we expect them
    to fail sometimes, and that's just fine.

The PCI HCDs will need simple changes to catch up to this, like being able
to ignore the setting of CONFIG_USB_SUSPEND.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hcd-pci.c |  106 +++++++++++++++++++++------------------------
 drivers/usb/core/hcd.h     |    6 +-
 2 files changed, 53 insertions(+), 59 deletions(-)
---
 drivers/usb/core/hcd-pci.c | 106 +++++++++++++++++++++------------------------
 drivers/usb/core/hcd.h     |   6 +--
 2 files changed, 53 insertions(+), 59 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hcd-pci.c b/drivers/usb/core/hcd-pci.c
index 6385d1a..84d9e69 100644
--- a/drivers/usb/core/hcd-pci.c
+++ b/drivers/usb/core/hcd-pci.c
@@ -30,6 +30,8 @@
 #include <asm/io.h>
 #include <asm/irq.h>
 #include <linux/usb.h>
+
+#include "usb.h"
 #include "hcd.h"
 
 
@@ -197,6 +199,26 @@ int usb_hcd_pci_suspend (struct pci_dev *dev, pm_message_t message)
 
 	hcd = pci_get_drvdata(dev);
 
+	/* Root hub suspend should have stopped all downstream traffic,
+	 * and all bus master traffic.  And done so for both the interface
+	 * and the stub usb_device (which we check here).  But maybe it
+	 * didn't; writing sysfs power/state files ignores such rules...
+	 *
+	 * We must ignore the FREEZE vs SUSPEND distinction here, because
+	 * otherwise the swsusp will save (and restore) garbage state.
+	 */
+	if (hcd->self.root_hub->dev.power.power_state.event == PM_EVENT_ON)
+		return -EBUSY;
+
+	if (hcd->driver->suspend) {
+		retval = hcd->driver->suspend(hcd, message);
+		if (retval) {
+			dev_dbg (&dev->dev, "PCI pre-suspend fail, %d\n",
+				retval);
+			goto done;
+		}
+	}
+
 	/* FIXME until the generic PM interfaces change a lot more, this
 	 * can't use PCI D1 and D2 states.  For example, the confusion
 	 * between messages and states will need to vanish, and messages
@@ -215,31 +237,13 @@ int usb_hcd_pci_suspend (struct pci_dev *dev, pm_message_t message)
 	 */
 	has_pci_pm = pci_find_capability(dev, PCI_CAP_ID_PM);
 
-	switch (hcd->state) {
-
-	/* entry if root hub wasn't yet suspended ... from sysfs,
-	 * without autosuspend, or if USB_SUSPEND isn't configured.
+	/* Downstream ports from this root hub should already be quiesced, so
+	 * there will be no DMA activity.  Now we can shut down the upstream
+	 * link (except maybe for PME# resume signaling) and enter some PCI
+	 * low power state, if the hardware allows.
 	 */
-	case HC_STATE_RUNNING:
-		hcd->state = HC_STATE_QUIESCING;
-		retval = hcd->driver->suspend (hcd, message);
-		if (retval) {
-			dev_dbg (hcd->self.controller, 
-					"suspend fail, retval %d\n",
-					retval);
-			break;
-		}
-		hcd->state = HC_STATE_SUSPENDED;
-		/* FALLTHROUGH */
+	if (hcd->state == HC_STATE_SUSPENDED) {
 
-	/* entry with CONFIG_USB_SUSPEND, or hcds that autosuspend: the
-	 * controller and/or root hub will already have been suspended,
-	 * but it won't be ready for a PCI resume call.
-	 *
-	 * FIXME only CONFIG_USB_SUSPEND guarantees hub_suspend() will
-	 * have been called, otherwise root hub timers still run ...
-	 */
-	case HC_STATE_SUSPENDED:
 		/* no DMA or IRQs except when HC is active */
 		if (dev->current_state == PCI_D0) {
 			pci_save_state (dev);
@@ -248,7 +252,7 @@ int usb_hcd_pci_suspend (struct pci_dev *dev, pm_message_t message)
 
 		if (!has_pci_pm) {
 			dev_dbg (hcd->self.controller, "--> PCI D0/legacy\n");
-			break;
+			goto done;
 		}
 
 		/* NOTE:  dev->current_state becomes nonzero only here, and
@@ -259,28 +263,29 @@ int usb_hcd_pci_suspend (struct pci_dev *dev, pm_message_t message)
 		retval = pci_set_power_state (dev, PCI_D3hot);
 		if (retval == 0) {
 			dev_dbg (hcd->self.controller, "--> PCI D3\n");
-			retval = pci_enable_wake (dev, PCI_D3hot, hcd->remote_wakeup);
-			if (retval)
-				break;
-			retval = pci_enable_wake (dev, PCI_D3cold, hcd->remote_wakeup);
-		} else if (retval < 0) {
+
+			/* Ignore these return values.  We rely on pci code to
+			 * reject requests the hardware can't implement, rather
+			 * than coding the same thing.
+			 */
+			(void) pci_enable_wake (dev, PCI_D3hot, hcd->remote_wakeup);
+			(void) pci_enable_wake (dev, PCI_D3cold, hcd->remote_wakeup);
+		} else {
 			dev_dbg (&dev->dev, "PCI D3 suspend fail, %d\n",
 					retval);
 			(void) usb_hcd_pci_resume (dev);
-			break;
 		}
-		break;
-	default:
+
+	} else {
 		dev_dbg (hcd->self.controller, "hcd state %d; not suspended\n",
 			hcd->state);
 		WARN_ON(1);
 		retval = -EINVAL;
-		break;
 	}
 
-	/* update power_state **ONLY** to make sysfs happier */
+done:
 	if (retval == 0)
-		dev->dev.power.power_state = message;
+		dev->dev.power.power_state = PMSG_SUSPEND;
 	return retval;
 }
 EXPORT_SYMBOL (usb_hcd_pci_suspend);
@@ -336,20 +341,9 @@ int usb_hcd_pci_resume (struct pci_dev *dev)
 				dev->current_state);
 		}
 #endif
-		retval = pci_enable_wake (dev, dev->current_state, 0);
-		if (retval) {
-			dev_err(hcd->self.controller,
-				"can't enable_wake to %d, %d!\n",
-				dev->current_state, retval);
-			return retval;
-		}
-		retval = pci_enable_wake (dev, PCI_D3cold, 0);
-		if (retval) {
-			dev_err(hcd->self.controller,
-				"can't enable_wake to %d, %d!\n",
-				PCI_D3cold, retval);
-			return retval;
-		}
+		/* yes, ignore these results too... */
+		(void) pci_enable_wake (dev, dev->current_state, 0);
+		(void) pci_enable_wake (dev, PCI_D3cold, 0);
 	} else {
 		/* Same basic cases: clean (powered/not), dirty */
 		dev_dbg(hcd->self.controller, "PCI legacy resume\n");
@@ -371,17 +365,17 @@ int usb_hcd_pci_resume (struct pci_dev *dev)
 
 	dev->dev.power.power_state = PMSG_ON;
 
-	hcd->state = HC_STATE_RESUMING;
 	hcd->saw_irq = 0;
 
-	retval = hcd->driver->resume (hcd);
-	if (!HC_IS_RUNNING (hcd->state)) {
-		dev_dbg (hcd->self.controller, 
-				"resume fail, retval %d\n", retval);
-		usb_hc_died (hcd);
+	if (hcd->driver->resume) {
+		retval = hcd->driver->resume(hcd);
+		if (retval) {
+			dev_err (hcd->self.controller,
+				"PCI post-resume error %d!\n", retval);
+			usb_hc_died (hcd);
+		}
 	}
 
-	retval = pci_enable_device(dev);
 	return retval;
 }
 EXPORT_SYMBOL (usb_hcd_pci_resume);
diff --git a/drivers/usb/core/hcd.h b/drivers/usb/core/hcd.h
index eb21f13..74757fc 100644
--- a/drivers/usb/core/hcd.h
+++ b/drivers/usb/core/hcd.h
@@ -182,12 +182,12 @@ struct hc_driver {
 	int	(*start) (struct usb_hcd *hcd);
 
 	/* NOTE:  these suspend/resume calls relate to the HC as
-	 * a whole, not just the root hub; they're for bus glue.
+	 * a whole, not just the root hub; they're for PCI bus glue.
 	 */
-	/* called after all devices were suspended */
+	/* called after suspending the hub, before entering D3 etc */
 	int	(*suspend) (struct usb_hcd *hcd, pm_message_t message);
 
-	/* called before any devices get resumed */
+	/* called after entering D0 (etc), before resuming the hub */
 	int	(*resume) (struct usb_hcd *hcd);
 
 	/* cleanly make HCD stop writing memory and doing I/O */
-- 
cgit v1.1


From f197b2c54b9d9a133a9a8ff92f35cadf8945ea14 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Thu, 22 Sep 2005 22:42:53 -0700
Subject: [PATCH] OHCI PM updates

This simplifies the OHCI root hub suspend logic:

 - Uses new usbcore root hub calls to make autosuspend work again:
	* Uses a newish usbcore root hub wakeup mechanism,
	  making requests to khubd not keventd.
	* Uses an even newer sibling suspend hook.

 - Expect someone always made usbcore call ohci_hub_suspend() before bus
   glue fires; and that ohci_hub_resume() is only called after that bus
   glue ran.  Previously, only CONFIG_USB_SUSPEND promised those things.
   (Includes updates to PCI and OMAP bus glue.)

 - Handle a not-noticed-before special case during resume from one of
   the swsusp snapshots when using "usb-handoff":  the controller isn't
   left in RESET state.  (A bug to fix in the usb-handoff code...)

Also cleans up a minor debug printk glitch, and switches an mdelay over
to an msleep (how did that stick around for so long?).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/ohci-dbg.c  |    4 ----
 drivers/usb/host/ohci-hcd.c  |    2 +-
 drivers/usb/host/ohci-hub.c  |   42 ++++++++++++------------------------------
 drivers/usb/host/ohci-mem.c  |    1 -
 drivers/usb/host/ohci-omap.c |   36 ++++++++++++------------------------
 drivers/usb/host/ohci-pci.c  |   40 ++++++++--------------------------------
 drivers/usb/host/ohci.h      |    1 -
 7 files changed, 33 insertions(+), 93 deletions(-)
---
 drivers/usb/host/ohci-dbg.c  |  4 ----
 drivers/usb/host/ohci-hcd.c  |  2 +-
 drivers/usb/host/ohci-hub.c  | 42 ++++++++++++------------------------------
 drivers/usb/host/ohci-mem.c  |  1 -
 drivers/usb/host/ohci-omap.c | 38 +++++++++++++-------------------------
 drivers/usb/host/ohci-pci.c  | 40 ++++++++--------------------------------
 drivers/usb/host/ohci.h      |  1 -
 7 files changed, 34 insertions(+), 94 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/ohci-dbg.c b/drivers/usb/host/ohci-dbg.c
index 7924c74..7bfffcbb 100644
--- a/drivers/usb/host/ohci-dbg.c
+++ b/drivers/usb/host/ohci-dbg.c
@@ -193,10 +193,6 @@ ohci_dump_status (struct ohci_hcd *controller, char **next, unsigned *size)
 
 	maybe_print_eds (controller, "donehead",
 			ohci_readl (controller, &regs->donehead), next, size);
-
-	/* broken fminterval means traffic won't flow! */ 
-	ohci_dbg (controller, "fminterval %08x\n", 
-			ohci_readl (controller, &regs->fminterval));
 }
 
 #define dbg_port_sw(hc,num,value,next,size) \
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index c26ab5f..5c0c6c8 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -723,7 +723,7 @@ static irqreturn_t ohci_irq (struct usb_hcd *hcd, struct pt_regs *ptregs)
 		ohci_vdbg (ohci, "resume detect\n");
 		ohci_writel (ohci, OHCI_INTR_RD, &regs->intrstatus);
 		if (hcd->state != HC_STATE_QUIESCING)
-			schedule_work(&ohci->rh_resume);
+			usb_hcd_resume_root_hub(hcd);
 	}
 
 	if (ints & OHCI_INTR_WDH) {
diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c
index b96948e..39a60e7 100644
--- a/drivers/usb/host/ohci-hub.c
+++ b/drivers/usb/host/ohci-hub.c
@@ -73,7 +73,6 @@ static int ohci_hub_suspend (struct usb_hcd *hcd)
 	ohci_dbg (ohci, "suspend root hub\n");
 
 	/* First stop any processing */
-	hcd->state = HC_STATE_QUIESCING;
 	if (ohci->hc_control & OHCI_SCHED_ENABLES) {
 		int		limit;
 
@@ -108,7 +107,9 @@ static int ohci_hub_suspend (struct usb_hcd *hcd)
 	else
 		ohci->hc_control &= ~OHCI_CTRL_RWE;
 
-	/* Suspend hub */
+	/* Suspend hub ... this is the "global (to this bus) suspend" mode,
+	 * which doesn't imply ports will first be individually suspended.
+	 */
 	ohci->hc_control &= ~OHCI_CTRL_HCFS;
 	ohci->hc_control |= OHCI_USB_SUSPEND;
 	ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
@@ -118,8 +119,9 @@ static int ohci_hub_suspend (struct usb_hcd *hcd)
 	ohci->next_statechange = jiffies + msecs_to_jiffies (5);
 
 done:
+	/* external suspend vs self autosuspend ... same effect */
 	if (status == 0)
-		hcd->state = HC_STATE_SUSPENDED;
+		usb_hcd_suspend_root_hub(hcd);
 	spin_unlock_irqrestore (&ohci->lock, flags);
 	return status;
 }
@@ -146,7 +148,7 @@ static int ohci_hub_resume (struct usb_hcd *hcd)
 	ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
 
 	if (ohci->hc_control & (OHCI_CTRL_IR | OHCI_SCHED_ENABLES)) {
-		/* this can happen after suspend-to-disk */
+		/* this can happen after resuming a swsusp snapshot */
 		if (hcd->state == HC_STATE_RESUMING) {
 			ohci_dbg (ohci, "BIOS/SMM active, control %03x\n",
 					ohci->hc_control);
@@ -169,11 +171,12 @@ static int ohci_hub_resume (struct usb_hcd *hcd)
 		ohci_info (ohci, "wakeup\n");
 		break;
 	case OHCI_USB_OPER:
-		ohci_dbg (ohci, "already resumed\n");
-		status = 0;
+		/* this can happen after resuming a swsusp snapshot */
+		ohci_dbg (ohci, "snapshot resume? reinit\n");
+		status = -EBUSY;
 		break;
 	default:		/* RESET, we lost power */
-		ohci_dbg (ohci, "root hub hardware reset\n");
+		ohci_dbg (ohci, "lost power\n");
 		status = -EBUSY;
 	}
 	spin_unlock_irq (&ohci->lock);
@@ -198,8 +201,7 @@ static int ohci_hub_resume (struct usb_hcd *hcd)
 	}
 
 	/* Some controllers (lucent erratum) need extra-long delays */
-	hcd->state = HC_STATE_RESUMING;
-	mdelay (20 /* usb 11.5.1.10 */ + 15);
+	msleep (20 /* usb 11.5.1.10 */ + 12 /* 32 msec counter */ + 1);
 
 	temp = ohci_readl (ohci, &ohci->regs->control);
 	temp &= OHCI_CTRL_HCFS;
@@ -273,27 +275,9 @@ static int ohci_hub_resume (struct usb_hcd *hcd)
 		(void) ohci_readl (ohci, &ohci->regs->control);
 	}
 
-	hcd->state = HC_STATE_RUNNING;
 	return 0;
 }
 
-static void ohci_rh_resume (void *_hcd)
-{
-	struct usb_hcd	*hcd = _hcd;
-
-	usb_lock_device (hcd->self.root_hub);
-	(void) ohci_hub_resume (hcd);
-	usb_unlock_device (hcd->self.root_hub);
-}
-
-#else
-
-static void ohci_rh_resume (void *_hcd)
-{
-	struct ohci_hcd	*ohci = hcd_to_ohci (_hcd);
-	ohci_dbg(ohci, "rh_resume ??\n");
-}
-
 #endif	/* CONFIG_PM */
 
 /*-------------------------------------------------------------------------*/
@@ -367,7 +351,6 @@ done:
 #ifdef CONFIG_PM
 	/* save power by suspending idle root hubs;
 	 * INTR_RD wakes us when there's work
-	 * NOTE: if we can do this, we don't need a root hub timer!
 	 */
 	if (can_suspend
 			&& !changed
@@ -380,7 +363,6 @@ done:
 			) {
 		ohci_vdbg (ohci, "autosuspend\n");
 		(void) ohci_hub_suspend (hcd);
-		hcd->state = HC_STATE_RUNNING;
 		usb_unlock_device (hcd->self.root_hub);
 	}
 #endif
@@ -554,7 +536,7 @@ static int ohci_hub_control (
 			temp = RH_PS_POCI;
 			if ((ohci->hc_control & OHCI_CTRL_HCFS)
 					!= OHCI_USB_OPER)
-				schedule_work (&ohci->rh_resume);
+				usb_hcd_resume_root_hub(hcd);
 			break;
 		case USB_PORT_FEAT_C_SUSPEND:
 			temp = RH_PS_PSSC;
diff --git a/drivers/usb/host/ohci-mem.c b/drivers/usb/host/ohci-mem.c
index 9fb83df..bfbe328 100644
--- a/drivers/usb/host/ohci-mem.c
+++ b/drivers/usb/host/ohci-mem.c
@@ -28,7 +28,6 @@ static void ohci_hcd_init (struct ohci_hcd *ohci)
 	ohci->next_statechange = jiffies;
 	spin_lock_init (&ohci->lock);
 	INIT_LIST_HEAD (&ohci->pending);
-	INIT_WORK (&ohci->rh_resume, ohci_rh_resume, ohci_to_hcd(ohci));
 	ohci->reboot_notifier.notifier_call = ohci_reboot;
 }
 
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index e67c07d..b3498b9 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -458,41 +458,29 @@ static int ohci_hcd_omap_drv_remove(struct device *dev)
 static int ohci_omap_suspend(struct device *dev, pm_message_t message)
 {
 	struct ohci_hcd	*ohci = hcd_to_ohci(dev_get_drvdata(dev));
-	int		status = -EINVAL;
-
-	down(&ohci_to_hcd(ohci)->self.root_hub->serialize);
-	status = ohci_hub_suspend(ohci_to_hcd(ohci));
-	if (status == 0) {
-		omap_ohci_clock_power(0);
-		ohci_to_hcd(ohci)->self.root_hub->state =
-			USB_STATE_SUSPENDED;
-		ohci_to_hcd(ohci)->state = HC_STATE_SUSPENDED;
-		dev->power.power_state = PMSG_SUSPEND;
-	}
-	up(&ohci_to_hcd(ohci)->self.root_hub->serialize);
-	return status;
+
+	if (time_before(jiffies, ohci->next_statechange))
+		msleep(5);
+	ohci->next_statechange = jiffies;
+
+	omap_ohci_clock_power(0);
+	ohci_to_hcd(ohci)->state = HC_STATE_SUSPENDED;
+	dev->power.power_state = PMSG_SUSPEND;
+	return 0;
 }
 
 static int ohci_omap_resume(struct device *dev)
 {
 	struct ohci_hcd	*ohci = hcd_to_ohci(dev_get_drvdata(dev));
-	int		status = 0;
 
 	if (time_before(jiffies, ohci->next_statechange))
 		msleep(5);
 	ohci->next_statechange = jiffies;
+
 	omap_ohci_clock_power(1);
-#ifdef	CONFIG_USB_SUSPEND
-	/* get extra cleanup even if remote wakeup isn't in use */
-	status = usb_resume_device(ohci_to_hcd(ohci)->self.root_hub);
-#else
-	down(&ohci_to_hcd(ohci)->self.root_hub->serialize);
-	status = ohci_hub_resume(ohci_to_hcd(ohci));
-	up(&ohci_to_hcd(ohci)->self.root_hub->serialize);
-#endif
-	if (status == 0)
-		dev->power.power_state = PMSG_ON;
-	return status;
+	dev->power.power_state = PMSG_ON;
+	usb_hcd_resume_root_hub(dev_get_drvdata(dev));
+	return 0;
 }
 
 #endif
diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c
index 0afa237..99a0ad4 100644
--- a/drivers/usb/host/ohci-pci.c
+++ b/drivers/usb/host/ohci-pci.c
@@ -112,23 +112,13 @@ ohci_pci_start (struct usb_hcd *hcd)
 
 static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
 {
-	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
-
-	/* suspend root hub, hoping it keeps power during suspend */
-	if (time_before (jiffies, ohci->next_statechange))
-		msleep (100);
-
-#ifdef	CONFIG_USB_SUSPEND
-	(void) usb_suspend_device (hcd->self.root_hub);
-#else
-	usb_lock_device (hcd->self.root_hub);
-	(void) ohci_hub_suspend (hcd);
-	usb_unlock_device (hcd->self.root_hub);
-#endif
+	/* root hub was already suspended */
 
-	/* let things settle down a bit */
-	msleep (100);
-	
+	/* FIXME these PMAC things get called in the wrong places.  ASIC
+	 * clocks should be turned off AFTER entering D3, and on BEFORE
+	 * trying to enter D0.  Evidently the PCI layer doesn't currently
+	 * provide the right sort of platform hooks for this ...
+	 */
 #ifdef CONFIG_PPC_PMAC
 	if (_machine == _MACH_Pmac) {
 	   	struct device_node	*of_node;
@@ -145,9 +135,6 @@ static int ohci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
 
 static int ohci_pci_resume (struct usb_hcd *hcd)
 {
-	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
-	int			retval = 0;
-
 #ifdef CONFIG_PPC_PMAC
 	if (_machine == _MACH_Pmac) {
 		struct device_node *of_node;
@@ -159,19 +146,8 @@ static int ohci_pci_resume (struct usb_hcd *hcd)
 	}
 #endif /* CONFIG_PPC_PMAC */
 
-	/* resume root hub */
-	if (time_before (jiffies, ohci->next_statechange))
-		msleep (100);
-#ifdef	CONFIG_USB_SUSPEND
-	/* get extra cleanup even if remote wakeup isn't in use */
-	retval = usb_resume_device (hcd->self.root_hub);
-#else
-	usb_lock_device (hcd->self.root_hub);
-	retval = ohci_hub_resume (hcd);
-	usb_unlock_device (hcd->self.root_hub);
-#endif
-
-	return retval;
+	usb_hcd_resume_root_hub(hcd);
+	return 0;
 }
 
 #endif	/* CONFIG_PM */
diff --git a/drivers/usb/host/ohci.h b/drivers/usb/host/ohci.h
index 8a9b9d9..caacf14 100644
--- a/drivers/usb/host/ohci.h
+++ b/drivers/usb/host/ohci.h
@@ -389,7 +389,6 @@ struct ohci_hcd {
 	unsigned long		next_statechange;	/* suspend/resume */
 	u32			fminterval;		/* saved register */
 
-	struct work_struct	rh_resume;
 	struct notifier_block	reboot_notifier;
 
 	unsigned long		flags;		/* for HC bugs */
-- 
cgit v1.1


From f2cb36c1df427431a8c6096b4ad113df767c1bd9 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Thu, 22 Sep 2005 22:43:30 -0700
Subject: [PATCH] update PCI early-handoff handling for OHCI

The PCI "early usb handoff" quirk logic didn't work like "ohci-hcd" ...
This patch makes it do so by:

  - Resetting the controller after kicking BIOS off, matching the
    normal "chip in hardware reset" startup mode;

  - Reporting any BIOS that borks this simple handoff; it's likely
    got a few other surprises for us too.

  - Ignoring that handoff on HPPA;

The diagnostic string is mostly shared with EHCI, saving a few bytes.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/pci-quirks.c |   22 ++++++++++++++++++----
 1 file changed, 18 insertions(+), 4 deletions(-)
---
 drivers/usb/host/pci-quirks.c | 22 ++++++++++++++++++----
 1 file changed, 18 insertions(+), 4 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c
index 8ee5c3e..49f7381 100644
--- a/drivers/usb/host/pci-quirks.c
+++ b/drivers/usb/host/pci-quirks.c
@@ -60,6 +60,7 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82371AB_2,	qui
 #define OHCI_INTRENABLE		0x10
 #define OHCI_INTRDISABLE	0x14
 #define OHCI_OCR		(1 << 3)	/* ownership change request */
+#define OHCI_CTRL_RWC		(1 << 9)	/* remote wakeup connected */
 #define OHCI_CTRL_IR		(1 << 8)	/* interrupt routing */
 #define OHCI_INTR_OC		(1 << 30)	/* ownership change */
 
@@ -140,13 +141,17 @@ static void __devinit quirk_usb_handoff_ohci(struct pci_dev *pdev)
 {
 	void __iomem *base;
 	int wait_time;
+	u32 control;
 
 	base = ioremap_nocache(pci_resource_start(pdev, 0),
 				     pci_resource_len(pdev, 0));
 	if (base == NULL) return;
 
-	if (readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
-		wait_time = 500; /* 0.5 seconds */
+/* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */
+#ifndef __hppa__
+	control = readl(base + OHCI_CONTROL);
+	if (control & OHCI_CTRL_IR) {
+		wait_time = 500; /* arbitrary; 5 seconds */
 		writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
 		writel(OHCI_OCR, base + OHCI_CMDSTATUS);
 		while (wait_time > 0 &&
@@ -154,7 +159,15 @@ static void __devinit quirk_usb_handoff_ohci(struct pci_dev *pdev)
 			wait_time -= 10;
 			msleep(10);
 		}
+		if (wait_time <= 0)
+			printk(KERN_WARNING "%s %s: early BIOS handoff "
+					"failed (BIOS bug ?)\n",
+					pdev->dev.bus_id, "OHCI");
+
+		/* reset controller, preserving RWC */
+		writel(control & OHCI_CTRL_RWC, base + OHCI_CONTROL);
 	}
+#endif
 
 	/*
 	 * disable interrupts
@@ -211,8 +224,9 @@ static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev)
 				/*
 				 * well, possibly buggy BIOS...
 				 */
-				printk(KERN_WARNING "EHCI early BIOS handoff "
-						"failed (BIOS bug ?)\n");
+				printk(KERN_WARNING "%s %s: early BIOS handoff "
+						"failed (BIOS bug ?)\n",
+					pdev->dev.bus_id, "EHCI");
 				pci_write_config_dword(pdev,
 						hcc_params + EHCI_USBLEGSUP,
 						EHCI_USBLEGSUP_OS);
-- 
cgit v1.1


From a7f72abe8fac9b919135005e06216be8eef945a2 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Thu, 22 Sep 2005 22:44:56 -0700
Subject: [PATCH] UHCI PM updates

This removes suspend and resume path recursion in UHCI.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/uhci-hcd.c |    9 ---------
 1 file changed, 9 deletions(-)
---
 drivers/usb/host/uhci-hcd.c | 9 ---------
 1 file changed, 9 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c
index b44094f..34c9dbc 100644
--- a/drivers/usb/host/uhci-hcd.c
+++ b/drivers/usb/host/uhci-hcd.c
@@ -762,11 +762,6 @@ static int uhci_suspend(struct usb_hcd *hcd, pm_message_t message)
 	if (uhci->hc_inaccessible)	/* Dead or already suspended */
 		goto done;
 
-#ifndef CONFIG_USB_SUSPEND
-	/* Otherwise this would never happen */
-	suspend_rh(uhci, UHCI_RH_SUSPENDED);
-#endif
-
 	if (uhci->rh_state > UHCI_RH_SUSPENDED) {
 		dev_warn(uhci_dev(uhci), "Root hub isn't suspended!\n");
 		hcd->state = HC_STATE_RUNNING;
@@ -808,10 +803,6 @@ static int uhci_resume(struct usb_hcd *hcd)
 	check_and_reset_hc(uhci);
 	configure_hc(uhci);
 
-#ifndef CONFIG_USB_SUSPEND
-	/* Otherwise this would never happen */
-	wakeup_rh(uhci);
-#endif
 	if (uhci->rh_state == UHCI_RH_RESET)
 		suspend_rh(uhci, UHCI_RH_SUSPENDED);
 
-- 
cgit v1.1


From ccdcf77ae32e3d3347fdf3810b27f899e98c34fb Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Thu, 22 Sep 2005 22:45:13 -0700
Subject: [PATCH] ISP116x PM updates

This makes the isp116x driver stop using usb_suspend_device() and
usb_resume_device() ... usbcore now calls to the root hub methods,
removing the need for this.  It also switches from keventd to khubd
for remote wakeup.  (Compile tested.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/isp116x-hcd.c |   29 ++++-------------------------
 drivers/usb/host/isp116x.h     |    1 -
 2 files changed, 4 insertions(+), 26 deletions(-)
---
 drivers/usb/host/isp116x-hcd.c | 29 ++++-------------------------
 drivers/usb/host/isp116x.h     |  1 -
 2 files changed, 4 insertions(+), 26 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/isp116x-hcd.c b/drivers/usb/host/isp116x-hcd.c
index 554d602..f68220f 100644
--- a/drivers/usb/host/isp116x-hcd.c
+++ b/drivers/usb/host/isp116x-hcd.c
@@ -638,7 +638,7 @@ static irqreturn_t isp116x_irq(struct usb_hcd *hcd, struct pt_regs *regs)
 				  + msecs_to_jiffies(20) + 1);
 		if (intstat & HCINT_RD) {
 			DBG("---- remote wakeup\n");
-			schedule_work(&isp116x->rh_resume);
+			usb_hcd_resume_root_hub(hcd);
 			ret = IRQ_HANDLED;
 		}
 		irqstat &= ~HCuPINT_OPR;
@@ -1263,22 +1263,12 @@ static int isp116x_hub_resume(struct usb_hcd *hcd)
 	return 0;
 }
 
-static void isp116x_rh_resume(void *_hcd)
-{
-	struct usb_hcd *hcd = _hcd;
-
-	usb_resume_device(hcd->self.root_hub);
-}
 
 #else
 
 #define	isp116x_hub_suspend	NULL
 #define	isp116x_hub_resume	NULL
 
-static void isp116x_rh_resume(void *_hcd)
-{
-}
-
 #endif
 
 /*-----------------------------------------------------------------*/
@@ -1732,7 +1722,6 @@ static int __init isp116x_probe(struct device *dev)
 	isp116x->addr_reg = addr_reg;
 	spin_lock_init(&isp116x->lock);
 	INIT_LIST_HEAD(&isp116x->async);
-	INIT_WORK(&isp116x->rh_resume, isp116x_rh_resume, hcd);
 	isp116x->board = dev->platform_data;
 
 	if (!isp116x->board) {
@@ -1777,16 +1766,10 @@ static int __init isp116x_probe(struct device *dev)
 static int isp116x_suspend(struct device *dev, pm_message_t state)
 {
 	int ret = 0;
-	struct usb_hcd *hcd = dev_get_drvdata(dev);
 
 	VDBG("%s: state %x\n", __func__, state);
 
-	ret = usb_suspend_device(hcd->self.root_hub);
-	if (!ret) {
-		dev->power.power_state = state;
-		INFO("%s suspended\n", hcd_name);
-	} else
-		ERR("%s suspend failed\n", hcd_name);
+	dev->power.power_state = state;
 
 	return ret;
 }
@@ -1797,15 +1780,11 @@ static int isp116x_suspend(struct device *dev, pm_message_t state)
 static int isp116x_resume(struct device *dev)
 {
 	int ret = 0;
-	struct usb_hcd *hcd = dev_get_drvdata(dev);
 
 	VDBG("%s:  state %x\n", __func__, dev->power.power_state);
 
-	ret = usb_resume_device(hcd->self.root_hub);
-	if (!ret) {
-		dev->power.power_state = PMSG_ON;
-		VDBG("%s resumed\n", (char *)hcd_name);
-	}
+	dev->power.power_state = PMSG_ON;
+
 	return ret;
 }
 
diff --git a/drivers/usb/host/isp116x.h b/drivers/usb/host/isp116x.h
index 5887347..c6fec96 100644
--- a/drivers/usb/host/isp116x.h
+++ b/drivers/usb/host/isp116x.h
@@ -253,7 +253,6 @@ static const int cc_to_error[16] = {
 
 struct isp116x {
 	spinlock_t lock;
-	struct work_struct rh_resume;
 
 	void __iomem *addr_reg;
 	void __iomem *data_reg;
-- 
cgit v1.1


From 5edbfb7c8af0577097dae87cdd4dfdba82bb9579 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Thu, 22 Sep 2005 22:45:26 -0700
Subject: [PATCH] stop exporting two functions

The way we're looking at USB suspend lately doesn't expect drivers to
call usb_suspend_device() or usb_resume_device() directly; that'll
be implicit when no interfaces are in use.

This patch removes those APIs from visibility outside usbcore.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

 drivers/usb/core/hub.c |   12 ++++--------
 drivers/usb/core/usb.h |    4 ++++
 include/linux/usb.h    |    5 -----
 3 files changed, 8 insertions(+), 13 deletions(-)
---
 drivers/usb/core/hub.c | 12 ++++--------
 drivers/usb/core/usb.h |  4 ++++
 2 files changed, 8 insertions(+), 8 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 6a601a4..15db5e4 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1652,10 +1652,10 @@ static int __usb_suspend_device (struct usb_device *udev, int port1)
 
 #endif
 
-/**
+/*
  * usb_suspend_device - suspend a usb device
  * @udev: device that's no longer in active use
- * Context: must be able to sleep; device not locked
+ * Context: must be able to sleep; device not locked; pm locks held
  *
  * Suspends a USB device that isn't in active use, conserving power.
  * Devices may wake out of a suspend, if anything important happens,
@@ -1820,10 +1820,10 @@ hub_port_resume(struct usb_hub *hub, int port1, struct usb_device *udev)
 
 #endif
 
-/**
+/*
  * usb_resume_device - re-activate a suspended usb device
  * @udev: device to re-activate
- * Context: must be able to sleep; device not locked
+ * Context: must be able to sleep; device not locked; pm locks held
  *
  * This will re-activate the suspended device, increasing power usage
  * while letting drivers communicate again with its endpoints.
@@ -2024,10 +2024,6 @@ void usb_resume_root_hub(struct usb_device *hdev)
 	kick_khubd(hub);
 }
 
-EXPORT_SYMBOL(usb_suspend_device);
-EXPORT_SYMBOL(usb_resume_device);
-
-
 
 /* USB 2.0 spec, 7.1.7.3 / fig 7-29:
  *
diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
index 7add46e..4d59f6e 100644
--- a/drivers/usb/core/usb.h
+++ b/drivers/usb/core/usb.h
@@ -29,6 +29,10 @@ extern void usb_major_cleanup(void);
 extern int usb_host_init(void);
 extern void usb_host_cleanup(void);
 
+extern int usb_suspend_device(struct usb_device *dev);
+extern int usb_resume_device(struct usb_device *dev);
+
+
 /* Interfaces and their "power state" are owned by usbcore */
 
 static inline void mark_active(struct usb_interface *f)
-- 
cgit v1.1


From b13296c6617f22e8c0174a7af32780617db0e680 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Tue, 27 Sep 2005 10:38:54 -0700
Subject: [PATCH] updates for "controller suspended" handling

Reject URBs to _all_ devices when their host controllers are suspended;
even root hub registers will be unavailable.  Also, don't reject urbs
to root hubs in other cases; the only upstream link is through that
controller (on PCI or whatever SOC bus is in use).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hcd.c |   28 ++++++++++++----------------
 drivers/usb/core/urb.c |    3 ++-
 2 files changed, 14 insertions(+), 17 deletions(-)
---
 drivers/usb/core/hcd.c | 28 ++++++++++++----------------
 drivers/usb/core/urb.c |  3 ++-
 2 files changed, 14 insertions(+), 17 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index de59bb5..b7bb8dd 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -458,22 +458,18 @@ static int rh_call_control (struct usb_hcd *hcd, struct urb *urb)
 
 	default:
 		/* non-generic request */
-		if (HC_IS_SUSPENDED (hcd->state))
-			status = -EAGAIN;
-		else {
-			switch (typeReq) {
-			case GetHubStatus:
-			case GetPortStatus:
-				len = 4;
-				break;
-			case GetHubDescriptor:
-				len = sizeof (struct usb_hub_descriptor);
-				break;
-			}
-			status = hcd->driver->hub_control (hcd,
-				typeReq, wValue, wIndex,
-				tbuf, wLength);
+		switch (typeReq) {
+		case GetHubStatus:
+		case GetPortStatus:
+			len = 4;
+			break;
+		case GetHubDescriptor:
+			len = sizeof (struct usb_hub_descriptor);
+			break;
 		}
+		status = hcd->driver->hub_control (hcd,
+			typeReq, wValue, wIndex,
+			tbuf, wLength);
 		break;
 error:
 		/* "protocol stall" on error */
@@ -487,7 +483,7 @@ error:
 				"CTRL: TypeReq=0x%x val=0x%x "
 				"idx=0x%x len=%d ==> %d\n",
 				typeReq, wValue, wIndex,
-				wLength, urb->status);
+				wLength, status);
 		}
 	}
 	if (len) {
diff --git a/drivers/usb/core/urb.c b/drivers/usb/core/urb.c
index b32898e..f2a1fed 100644
--- a/drivers/usb/core/urb.c
+++ b/drivers/usb/core/urb.c
@@ -237,7 +237,8 @@ int usb_submit_urb(struct urb *urb, gfp_t mem_flags)
 	    (dev->state < USB_STATE_DEFAULT) ||
 	    (!dev->bus) || (dev->devnum <= 0))
 		return -ENODEV;
-	if (dev->state == USB_STATE_SUSPENDED)
+	if (dev->bus->controller->power.power_state.event != PM_EVENT_ON
+			|| dev->state == USB_STATE_SUSPENDED)
 		return -EHOSTUNREACH;
 	if (!(op = dev->bus->op) || !op->submit_urb)
 		return -ENODEV;
-- 
cgit v1.1


From d09d36a91c70cb3cc609d693bf6a7e7a266ff9e6 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Mon, 26 Sep 2005 16:22:45 -0400
Subject: [PATCH] USB: usb_bulk_message() handles interrupts endpoints

Because there is no bulk_interrupt_message() routine and no
USBDEVFS_INTERRUPT ioctl, people have been forced to abuse the
usb_bulk_message() routine and USBDEVFS_BULK by using them for interrupt
transfers as well as bulk transfers.

This patch (as567) formalizes this practice and adds code to
usb_bulk_message() for detecting when the target is really an interrupt
endpoint.  If it is, the routine submits an interrupt URB (using the
default interval) instead of a bulk URB.  In theory this should help HCDs
that don't like it when people try to mix transfer types, queuing both
periodic and non-periodic types for the same endpoint.

Not fully tested -- I don't have any programs that use USBDEVFS_BULK for
interrupt transfers -- but it compiles okay and normal bulk messages work
as well as before.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/message.c |   24 ++++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)
---
 drivers/usb/core/message.c | 24 ++++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c
index ebf59ea..574d0d4 100644
--- a/drivers/usb/core/message.c
+++ b/drivers/usb/core/message.c
@@ -187,21 +187,37 @@ int usb_control_msg(struct usb_device *dev, unsigned int pipe, __u8 request, __u
  *      If a thread in your driver uses this call, make sure your disconnect()
  *      method can wait for it to complete.  Since you don't have a handle on
  *      the URB used, you can't cancel the request.
+ *
+ *	Because there is no usb_interrupt_msg() and no USBDEVFS_INTERRUPT
+ *	ioctl, users are forced to abuse this routine by using it to submit
+ *	URBs for interrupt endpoints.  We will take the liberty of creating
+ *	an interrupt URB (with the default interval) if the target is an
+ *	interrupt endpoint.
  */
 int usb_bulk_msg(struct usb_device *usb_dev, unsigned int pipe, 
 			void *data, int len, int *actual_length, int timeout)
 {
 	struct urb *urb;
+	struct usb_host_endpoint *ep;
 
-	if (len < 0)
+	ep = (usb_pipein(pipe) ? usb_dev->ep_in : usb_dev->ep_out)
+			[usb_pipeendpoint(pipe)];
+	if (!ep || len < 0)
 		return -EINVAL;
 
-	urb=usb_alloc_urb(0, GFP_KERNEL);
+	urb = usb_alloc_urb(0, GFP_KERNEL);
 	if (!urb)
 		return -ENOMEM;
 
-	usb_fill_bulk_urb(urb, usb_dev, pipe, data, len,
-			  usb_api_blocking_completion, NULL);
+	if ((ep->desc.bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
+			USB_ENDPOINT_XFER_INT) {
+		pipe = (pipe & ~(3 << 30)) | (PIPE_INTERRUPT << 30);
+		usb_fill_int_urb(urb, usb_dev, pipe, data, len,
+				usb_api_blocking_completion, NULL,
+				ep->desc.bInterval);
+	} else
+		usb_fill_bulk_urb(urb, usb_dev, pipe, data, len,
+				usb_api_blocking_completion, NULL);
 
 	return usb_start_wait_urb(urb, timeout, actual_length);
 }
-- 
cgit v1.1


From 8b262bd25580e165710e8a27df19cd60c2ef58a3 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Mon, 26 Sep 2005 16:31:15 -0400
Subject: [PATCH] USB: UHCI: Spruce up some comments

This patch (as570) changes some comments in the uhci-hcd header file and
removes an unused declaration (something I forgot to erase in an earlier
patch).

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/host/uhci-hcd.h |   91 +++++++++++++++++++++++---------------------
 1 file changed, 49 insertions(+), 42 deletions(-)
---
 drivers/usb/host/uhci-hcd.h | 91 ++++++++++++++++++++++++---------------------
 1 file changed, 49 insertions(+), 42 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/uhci-hcd.h b/drivers/usb/host/uhci-hcd.h
index b04d99d..e576db5 100644
--- a/drivers/usb/host/uhci-hcd.h
+++ b/drivers/usb/host/uhci-hcd.h
@@ -7,6 +7,7 @@
 #define usb_packetid(pipe)	(usb_pipein(pipe) ? USB_PID_IN : USB_PID_OUT)
 #define PIPE_DEVEP_MASK		0x0007ff00
 
+
 /*
  * Universal Host Controller Interface data structures and defines
  */
@@ -82,15 +83,10 @@
 #define UHCI_MAX_SOF_NUMBER	2047	/* in an SOF packet */
 #define CAN_SCHEDULE_FRAMES	1000	/* how far future frames can be scheduled */
 
-struct uhci_frame_list {
-	__le32 frame[UHCI_NUMFRAMES];
-
-	void *frame_cpu[UHCI_NUMFRAMES];
 
-	dma_addr_t dma_handle;
-};
-
-struct urb_priv;
+/*
+ *	Queue Headers
+ */
 
 /*
  * One role of a QH is to hold a queue of TDs for some endpoint.  Each QH is
@@ -116,13 +112,13 @@ struct uhci_qh {
 
 	struct urb_priv *urbp;
 
-	struct list_head list;		/* P: uhci->frame_list_lock */
-	struct list_head remove_list;	/* P: uhci->remove_list_lock */
+	struct list_head list;
+	struct list_head remove_list;
 } __attribute__((aligned(16)));
 
 /*
  * We need a special accessor for the element pointer because it is
- * subject to asynchronous updates by the controller
+ * subject to asynchronous updates by the controller.
  */
 static __le32 inline qh_element(struct uhci_qh *qh) {
 	__le32 element = qh->element;
@@ -131,6 +127,11 @@ static __le32 inline qh_element(struct uhci_qh *qh) {
 	return element;
 }
 
+
+/*
+ *	Transfer Descriptors
+ */
+
 /*
  * for TD <status>:
  */
@@ -183,17 +184,10 @@ static __le32 inline qh_element(struct uhci_qh *qh) {
  *
  * That's silly, the hardware doesn't care. The hardware only cares that
  * the hardware words are 16-byte aligned, and we can have any amount of
- * sw space after the TD entry as far as I can tell.
- *
- * But let's just go with the documentation, at least for 32-bit machines.
- * On 64-bit machines we probably want to take advantage of the fact that
- * hw doesn't really care about the size of the sw-only area.
- *
- * Alas, not anymore, we have more than 4 words for software, woops.
- * Everything still works tho, surprise! -jerdfelt
+ * sw space after the TD entry.
  *
  * td->link points to either another TD (not necessarily for the same urb or
- * even the same endpoint), or nothing (PTR_TERM), or a QH (for queued urbs)
+ * even the same endpoint), or nothing (PTR_TERM), or a QH (for queued urbs).
  */
 struct uhci_td {
 	/* Hardware fields */
@@ -205,16 +199,16 @@ struct uhci_td {
 	/* Software fields */
 	dma_addr_t dma_handle;
 
-	struct list_head list;		/* P: urb->lock */
-	struct list_head remove_list;	/* P: uhci->td_remove_list_lock */
+	struct list_head list;
+	struct list_head remove_list;
 
 	int frame;			/* for iso: what frame? */
-	struct list_head fl_list;	/* P: uhci->frame_list_lock */
+	struct list_head fl_list;
 } __attribute__((aligned(16)));
 
 /*
  * We need a special accessor for the control/status word because it is
- * subject to asynchronous updates by the controller
+ * subject to asynchronous updates by the controller.
  */
 static u32 inline td_status(struct uhci_td *td) {
 	__le32 status = td->status;
@@ -225,6 +219,10 @@ static u32 inline td_status(struct uhci_td *td) {
 
 
 /*
+ *	Skeleton Queue Headers
+ */
+
+/*
  * The UHCI driver places Interrupt, Control and Bulk into QH's both
  * to group together TD's for one transfer, and also to faciliate queuing
  * of URB's. To make it easy to insert entries into the schedule, we have
@@ -254,15 +252,15 @@ static u32 inline td_status(struct uhci_td *td) {
  *
  * The terminating QH is used for 2 reasons:
  * - To place a terminating TD which is used to workaround a PIIX bug
- *   (see Intel errata for explanation)
+ *   (see Intel errata for explanation), and
  * - To loop back to the full-speed control queue for full-speed bandwidth
- *   reclamation
+ *   reclamation.
  *
  * Isochronous transfers are stored before the start of the skeleton
  * schedule and don't use QH's. While the UHCI spec doesn't forbid the
- * use of QH's for Isochronous, it doesn't use them either. Since we don't
- * need to use them either, we follow the spec diagrams in hope that it'll
- * be more compatible with future UHCI implementations.
+ * use of QH's for Isochronous, it doesn't use them either. And the spec
+ * says that queues never advance on an error completion status, which
+ * makes them totally unsuitable for Isochronous transfers.
  */
 
 #define UHCI_NUM_SKELQH		12
@@ -312,8 +310,13 @@ static inline int __interval_to_skel(int interval)
 	return 0;				/* int128 for 128-255 ms (Max.) */
 }
 
+
+/*
+ *	The UHCI controller and root hub
+ */
+
 /*
- * States for the root hub.
+ * States for the root hub:
  *
  * To prevent "bouncing" in the presence of electrical noise,
  * when there are no devices attached we delay for 1 second in the
@@ -324,7 +327,7 @@ static inline int __interval_to_skel(int interval)
  */
 enum uhci_rh_state {
 	/* In the following states the HC must be halted.
-	 * These two must come first */
+	 * These two must come first. */
 	UHCI_RH_RESET,
 	UHCI_RH_SUSPENDED,
 
@@ -336,13 +339,13 @@ enum uhci_rh_state {
 	UHCI_RH_SUSPENDING,
 
 	/* In the following states it's an error if the HC is halted.
-	 * These two must come last */
+	 * These two must come last. */
 	UHCI_RH_RUNNING,		/* The normal state */
 	UHCI_RH_RUNNING_NODEVS,		/* Running with no devices attached */
 };
 
 /*
- * This describes the full uhci information.
+ * The full UHCI controller information:
  */
 struct uhci_hcd {
 
@@ -361,7 +364,7 @@ struct uhci_hcd {
 	spinlock_t lock;
 
 	dma_addr_t frame_dma_handle;		/* Hardware frame list */
-	__le32 *frame;				/* P: uhci->lock */
+	__le32 *frame;
 	void **frame_cpu;			/* CPU's frame list */
 
 	int fsbr;				/* Full-speed bandwidth reclamation */
@@ -387,22 +390,22 @@ struct uhci_hcd {
 	unsigned long ports_timeout;		/* Time to stop signalling */
 
 	/* Main list of URB's currently controlled by this HC */
-	struct list_head urb_list;		/* P: uhci->lock */
+	struct list_head urb_list;
 
 	/* List of QH's that are done, but waiting to be unlinked (race) */
-	struct list_head qh_remove_list;	/* P: uhci->lock */
+	struct list_head qh_remove_list;
 	unsigned int qh_remove_age;		/* Age in frames */
 
 	/* List of TD's that are done, but waiting to be freed (race) */
-	struct list_head td_remove_list;	/* P: uhci->lock */
+	struct list_head td_remove_list;
 	unsigned int td_remove_age;		/* Age in frames */
 
 	/* List of asynchronously unlinked URB's */
-	struct list_head urb_remove_list;	/* P: uhci->lock */
+	struct list_head urb_remove_list;
 	unsigned int urb_remove_age;		/* Age in frames */
 
 	/* List of URB's awaiting completion callback */
-	struct list_head complete_list;		/* P: uhci->lock */
+	struct list_head complete_list;
 
 	int rh_numports;			/* Number of root-hub ports */
 
@@ -421,13 +424,17 @@ static inline struct usb_hcd *uhci_to_hcd(struct uhci_hcd *uhci)
 
 #define uhci_dev(u)	(uhci_to_hcd(u)->self.controller)
 
+
+/*
+ *	Private per-URB data
+ */
 struct urb_priv {
 	struct list_head urb_list;
 
 	struct urb *urb;
 
 	struct uhci_qh *qh;		/* QH for this URB */
-	struct list_head td_list;	/* P: urb->lock */
+	struct list_head td_list;
 
 	unsigned fsbr : 1;		/* URB turned on FSBR */
 	unsigned fsbr_timeout : 1;	/* URB timed out on FSBR */
@@ -438,9 +445,10 @@ struct urb_priv {
 
 	unsigned long fsbrtime;		/* In jiffies */
 
-	struct list_head queue_list;	/* P: uhci->frame_list_lock */
+	struct list_head queue_list;
 };
 
+
 /*
  * Locking in uhci.c
  *
@@ -460,6 +468,5 @@ struct urb_priv {
 
 #define PCI_VENDOR_ID_GENESYS		0x17a0
 #define PCI_DEVICE_ID_GL880S_UHCI	0x8083
-#define PCI_DEVICE_ID_GL880S_EHCI	0x8084
 
 #endif
-- 
cgit v1.1


From dabb592816444fcba1a771e27d4f72a2b8218374 Mon Sep 17 00:00:00 2001
From: Andrew Morton <akpm@osdl.org>
Date: Thu, 22 Sep 2005 23:55:22 -0700
Subject: [PATCH] USB: sisusb warning fix

drivers/usb/misc/sisusbvga/sisusb.c: In function `sisusb_reset_text_mode':
drivers/usb/misc/sisusbvga/sisusb.c:2461: warning: assignment discards qualifiers from pointer target type

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/misc/sisusbvga/sisusb.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
---
 drivers/usb/misc/sisusbvga/sisusb.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers')

diff --git a/drivers/usb/misc/sisusbvga/sisusb.c b/drivers/usb/misc/sisusbvga/sisusb.c
index 222ae9c..c946c9a 100644
--- a/drivers/usb/misc/sisusbvga/sisusb.c
+++ b/drivers/usb/misc/sisusbvga/sisusb.c
@@ -2440,7 +2440,7 @@ int
 sisusb_reset_text_mode(struct sisusb_usb_data *sisusb, int init)
 {
 	int ret = 0, slot = sisusb->font_slot, i;
-	struct font_desc *myfont;
+	const struct font_desc *myfont;
 	u8 *tempbuf;
 	u16 *tempbufb;
 	size_t written;
-- 
cgit v1.1


From 22efcf4adec4262e0f49e6225f6cd070e4a85d20 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Mon, 26 Sep 2005 16:12:02 -0400
Subject: [PATCH] USB: File-Storage gadget: use the kthread API

This patch (as566) converts the File-Storage gadget over to the kthread
API.  The new code doesn't use kthread_stop because the control thread
needs to terminate asynchronously when it receives a signal.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/gadget/file_storage.c |   32 +++++++++++++-------------------
 1 file changed, 13 insertions(+), 19 deletions(-)
---
 drivers/usb/gadget/file_storage.c | 32 +++++++++++++-------------------
 1 file changed, 13 insertions(+), 19 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/gadget/file_storage.c b/drivers/usb/gadget/file_storage.c
index a41d9d4..241c570 100644
--- a/drivers/usb/gadget/file_storage.c
+++ b/drivers/usb/gadget/file_storage.c
@@ -224,6 +224,7 @@
 #include <linux/fs.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
+#include <linux/kthread.h>
 #include <linux/limits.h>
 #include <linux/list.h>
 #include <linux/module.h>
@@ -669,7 +670,6 @@ struct fsg_dev {
 	wait_queue_head_t	thread_wqh;
 	int			thread_wakeup_needed;
 	struct completion	thread_notifier;
-	int			thread_pid;
 	struct task_struct	*thread_task;
 	sigset_t		thread_signal_mask;
 
@@ -1084,7 +1084,6 @@ static void wakeup_thread(struct fsg_dev *fsg)
 static void raise_exception(struct fsg_dev *fsg, enum fsg_state new_state)
 {
 	unsigned long		flags;
-	struct task_struct	*thread_task;
 
 	/* Do nothing if a higher-priority exception is already in progress.
 	 * If a lower-or-equal priority exception is in progress, preempt it
@@ -1093,9 +1092,9 @@ static void raise_exception(struct fsg_dev *fsg, enum fsg_state new_state)
 	if (fsg->state <= new_state) {
 		fsg->exception_req_tag = fsg->ep0_req_tag;
 		fsg->state = new_state;
-		thread_task = fsg->thread_task;
-		if (thread_task)
-			send_sig_info(SIGUSR1, SEND_SIG_FORCED, thread_task);
+		if (fsg->thread_task)
+			send_sig_info(SIGUSR1, SEND_SIG_FORCED,
+					fsg->thread_task);
 	}
 	spin_unlock_irqrestore(&fsg->lock, flags);
 }
@@ -3383,11 +3382,6 @@ static int fsg_main_thread(void *fsg_)
 {
 	struct fsg_dev		*fsg = (struct fsg_dev *) fsg_;
 
-	fsg->thread_task = current;
-
-	/* Release all our userspace resources */
-	daemonize("file-storage-gadget");
-
 	/* Allow the thread to be killed by a signal, but set the signal mask
 	 * to block everything but INT, TERM, KILL, and USR1. */
 	siginitsetinv(&fsg->thread_signal_mask, sigmask(SIGINT) |
@@ -3400,9 +3394,6 @@ static int fsg_main_thread(void *fsg_)
 	 * that expects a __user pointer and it will work okay. */
 	set_fs(get_ds());
 
-	/* Wait for the gadget registration to finish up */
-	wait_for_completion(&fsg->thread_notifier);
-
 	/* The main loop */
 	while (fsg->state != FSG_STATE_TERMINATED) {
 		if (exception_in_progress(fsg) || signal_pending(current)) {
@@ -3440,8 +3431,9 @@ static int fsg_main_thread(void *fsg_)
 		spin_unlock_irq(&fsg->lock);
 		}
 
+	spin_lock_irq(&fsg->lock);
 	fsg->thread_task = NULL;
-	flush_signals(current);
+	spin_unlock_irq(&fsg->lock);
 
 	/* In case we are exiting because of a signal, unregister the
 	 * gadget driver and close the backing file. */
@@ -3959,10 +3951,12 @@ static int __init fsg_bind(struct usb_gadget *gadget)
 		sprintf(&serial[i], "%02X", c);
 	}
 
-	if ((rc = kernel_thread(fsg_main_thread, fsg, (CLONE_VM | CLONE_FS |
-			CLONE_FILES))) < 0)
+	fsg->thread_task = kthread_create(fsg_main_thread, fsg,
+			"file-storage-gadget");
+	if (IS_ERR(fsg->thread_task)) {
+		rc = PTR_ERR(fsg->thread_task);
 		goto out;
-	fsg->thread_pid = rc;
+	}
 
 	INFO(fsg, DRIVER_DESC ", version: " DRIVER_VERSION "\n");
 	INFO(fsg, "Number of LUNs=%d\n", fsg->nluns);
@@ -3994,7 +3988,7 @@ static int __init fsg_bind(struct usb_gadget *gadget)
 	DBG(fsg, "removable=%d, stall=%d, buflen=%u\n",
 			mod_data.removable, mod_data.can_stall,
 			mod_data.buflen);
-	DBG(fsg, "I/O thread pid: %d\n", fsg->thread_pid);
+	DBG(fsg, "I/O thread pid: %d\n", fsg->thread_task->pid);
 	return 0;
 
 autoconf_fail:
@@ -4093,7 +4087,7 @@ static int __init fsg_init(void)
 	set_bit(REGISTERED, &fsg->atomic_bitflags);
 
 	/* Tell the thread to start working */
-	complete(&fsg->thread_notifier);
+	wake_up_process(fsg->thread_task);
 	return 0;
 }
 module_init(fsg_init);
-- 
cgit v1.1


From 74ad9bd2fcf0fa203655e0d904809b06c4202bf8 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: make wHubCharacteristics __le16 to match other usb
 descriptor fields

Also has the nice benefit of making sparc alignment issues go away.

Thanks to David Miller for pointing out the problems here.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/core/hub.c |   22 ++++++++++++----------
 drivers/usb/core/hub.h |    2 +-
 2 files changed, 13 insertions(+), 11 deletions(-)
---
 drivers/usb/core/hub.c | 22 ++++++++++++----------
 drivers/usb/core/hub.h |  2 +-
 2 files changed, 13 insertions(+), 11 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 15db5e4..e2802bf 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -436,9 +436,10 @@ static void hub_power_on(struct usb_hub *hub)
 {
 	int port1;
 	unsigned pgood_delay = hub->descriptor->bPwrOn2PwrGood * 2;
+	u16 wHubCharacteristics = le16_to_cpu(hub->descriptor->wHubCharacteristics);
 
 	/* if hub supports power switching, enable power on each port */
-	if ((hub->descriptor->wHubCharacteristics & HUB_CHAR_LPSM) < 2) {
+	if ((wHubCharacteristics & HUB_CHAR_LPSM) < 2) {
 		dev_dbg(hub->intfdev, "enabling power on all ports\n");
 		for (port1 = 1; port1 <= hub->descriptor->bNbrPorts; port1++)
 			set_port_feature(hub->hdev, port1,
@@ -525,6 +526,7 @@ static int hub_configure(struct usb_hub *hub,
 	struct usb_device *hdev = hub->hdev;
 	struct device *hub_dev = hub->intfdev;
 	u16 hubstatus, hubchange;
+	u16 wHubCharacteristics;
 	unsigned int pipe;
 	int maxp, ret;
 	char *message;
@@ -570,9 +572,9 @@ static int hub_configure(struct usb_hub *hub,
 	dev_info (hub_dev, "%d port%s detected\n", hdev->maxchild,
 		(hdev->maxchild == 1) ? "" : "s");
 
-	le16_to_cpus(&hub->descriptor->wHubCharacteristics);
+	wHubCharacteristics = le16_to_cpu(hub->descriptor->wHubCharacteristics);
 
-	if (hub->descriptor->wHubCharacteristics & HUB_CHAR_COMPOUND) {
+	if (wHubCharacteristics & HUB_CHAR_COMPOUND) {
 		int	i;
 		char	portstr [USB_MAXCHILDREN + 1];
 
@@ -585,7 +587,7 @@ static int hub_configure(struct usb_hub *hub,
 	} else
 		dev_dbg(hub_dev, "standalone hub\n");
 
-	switch (hub->descriptor->wHubCharacteristics & HUB_CHAR_LPSM) {
+	switch (wHubCharacteristics & HUB_CHAR_LPSM) {
 		case 0x00:
 			dev_dbg(hub_dev, "ganged power switching\n");
 			break;
@@ -598,7 +600,7 @@ static int hub_configure(struct usb_hub *hub,
 			break;
 	}
 
-	switch (hub->descriptor->wHubCharacteristics & HUB_CHAR_OCPM) {
+	switch (wHubCharacteristics & HUB_CHAR_OCPM) {
 		case 0x00:
 			dev_dbg(hub_dev, "global over-current protection\n");
 			break;
@@ -638,7 +640,7 @@ static int hub_configure(struct usb_hub *hub,
 	}
 
 	/* Note 8 FS bit times == (8 bits / 12000000 bps) ~= 666ns */
-	switch (hub->descriptor->wHubCharacteristics & HUB_CHAR_TTTT) {
+	switch (wHubCharacteristics & HUB_CHAR_TTTT) {
 		case HUB_TTTT_8_BITS:
 			if (hdev->descriptor.bDeviceProtocol != 0) {
 				hub->tt.think_time = 666;
@@ -668,7 +670,7 @@ static int hub_configure(struct usb_hub *hub,
 	}
 
 	/* probe() zeroes hub->indicator[] */
-	if (hub->descriptor->wHubCharacteristics & HUB_CHAR_PORTIND) {
+	if (wHubCharacteristics & HUB_CHAR_PORTIND) {
 		hub->has_indicators = 1;
 		dev_dbg(hub_dev, "Port indicators are supported\n");
 	}
@@ -713,7 +715,7 @@ static int hub_configure(struct usb_hub *hub,
 			(hubstatus & HUB_STATUS_LOCAL_POWER)
 			? "lost (inactive)" : "good");
 
-	if ((hub->descriptor->wHubCharacteristics & HUB_CHAR_OCPM) == 0)
+	if ((wHubCharacteristics & HUB_CHAR_OCPM) == 0)
 		dev_dbg(hub_dev, "%sover-current condition exists\n",
 			(hubstatus & HUB_STATUS_OVERCURRENT) ? "" : "no ");
 
@@ -2432,6 +2434,7 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1,
 {
 	struct usb_device *hdev = hub->hdev;
 	struct device *hub_dev = hub->intfdev;
+	u16 wHubCharacteristics = le16_to_cpu(hub->descriptor->wHubCharacteristics);
 	int status, i;
  
 	dev_dbg (hub_dev,
@@ -2469,8 +2472,7 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1,
 	if (!(portstatus & USB_PORT_STAT_CONNECTION)) {
 
 		/* maybe switch power back on (e.g. root hub was reset) */
-		if ((hub->descriptor->wHubCharacteristics
-					& HUB_CHAR_LPSM) < 2
+		if ((wHubCharacteristics & HUB_CHAR_LPSM) < 2
 				&& !(portstatus & (1 << USB_PORT_FEAT_POWER)))
 			set_port_feature(hdev, port1, USB_PORT_FEAT_POWER);
  
diff --git a/drivers/usb/core/hub.h b/drivers/usb/core/hub.h
index e7fa9b5..bf23f89 100644
--- a/drivers/usb/core/hub.h
+++ b/drivers/usb/core/hub.h
@@ -131,7 +131,7 @@ struct usb_hub_descriptor {
 	__u8  bDescLength;
 	__u8  bDescriptorType;
 	__u8  bNbrPorts;
-	__u16 wHubCharacteristics;
+	__le16 wHubCharacteristics;
 	__u8  bPwrOn2PwrGood;
 	__u8  bHubContrCurrent;
 	    	/* add 1 bit for hub status change; round to bytes */
-- 
cgit v1.1


From 207c47e1fbc8d51500997bfa67c26c00114fab04 Mon Sep 17 00:00:00 2001
From: Thomas Riewe <thomasr@pyramid.de>
Date: Thu, 29 Sep 2005 14:57:29 +0200
Subject: [PATCH] drivers/usb/serial/ftdi_sio: add PID/VID

We would like to add a PID for the Pyramid Appliance Display, which works
on USB via FTDI_SIO.

Signed-off-by: Thomas Riewe <thomasr@pyramid.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/serial/ftdi_sio.c |    1 +
 drivers/usb/serial/ftdi_sio.h |    3 +++
 2 files changed, 4 insertions(+)
---
 drivers/usb/serial/ftdi_sio.c | 1 +
 drivers/usb/serial/ftdi_sio.h | 3 +++
 2 files changed, 4 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 8c12a0a..b713113 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -411,6 +411,7 @@ static struct usb_device_id id_table_combined [] = {
 	{ USB_DEVICE(FTDI_VID, FTDI_ELV_UM100_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_ELV_UR100_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_ELV_ALC8500_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_PYRAMID_PID) },
 	/*
 	 * These will probably use user-space drivers.  Uncomment them if
 	 * you need them or use the user-specified vendor/product module
diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h
index 7c65d46..ddb63df 100644
--- a/drivers/usb/serial/ftdi_sio.h
+++ b/drivers/usb/serial/ftdi_sio.h
@@ -342,6 +342,9 @@
 #define EVOLUTION_VID		0xDEEE	/* Vendor ID */
 #define EVOLUTION_ER1_PID	0x0300	/* ER1 Control Module */
 
+/* Pyramid Computer GmbH */
+#define FTDI_PYRAMID_PID	0xE6C8	/* Pyramid Appliance Display */
+
 /* Commands */
 #define FTDI_SIO_RESET 		0 /* Reset the port */
 #define FTDI_SIO_MODEM_CTRL 	1 /* Set the modem control register */
-- 
cgit v1.1


From ddcad752f206be7a0091a041403c3188f2febd16 Mon Sep 17 00:00:00 2001
From: Petko Manolov <petkan@nucleusys.com>
Date: Mon, 3 Oct 2005 17:24:11 +0300
Subject: [PATCH] pegasus.h

This one is a tiny patch adding one more device to the list.  Please
apply. :)

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/net/pegasus.h |    2 ++
 1 file changed, 2 insertions(+)
---
 drivers/usb/net/pegasus.h | 2 ++
 1 file changed, 2 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/net/pegasus.h b/drivers/usb/net/pegasus.h
index b98f2a8..9fbd59b 100644
--- a/drivers/usb/net/pegasus.h
+++ b/drivers/usb/net/pegasus.h
@@ -181,6 +181,8 @@ PEGASUS_DEV( "Accton USB 10/100 Ethernet Adapter", VENDOR_ACCTON, 0x1046,
 		DEFAULT_GPIO_RESET )
 PEGASUS_DEV( "SpeedStream USB 10/100 Ethernet", VENDOR_ACCTON, 0x5046,
 		DEFAULT_GPIO_RESET | PEGASUS_II )
+PEGASUS_DEV( "Philips USB 10/100 Ethernet", VENDOR_ACCTON, 0xb004,
+		DEFAULT_GPIO_RESET | PEGASUS_II )
 PEGASUS_DEV( "ADMtek ADM8511 \"Pegasus II\" USB Ethernet",
 		VENDOR_ADMTEK, 0x8511,
 		DEFAULT_GPIO_RESET | PEGASUS_II | HAS_HOME_PNA )
-- 
cgit v1.1


From 521daed8db4443a1574a98fc3abae8e230f09eaa Mon Sep 17 00:00:00 2001
From: Randy Dunlap <rdunlap@xenotime.net>
Date: Sun, 2 Oct 2005 17:15:33 -0700
Subject: [PATCH] safe_serial: use preprocessor directive for error

Use valid #preprocessor instruction to generate an error.

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
 drivers/usb/serial/safe_serial.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
---
 drivers/usb/serial/safe_serial.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers')

diff --git a/drivers/usb/serial/safe_serial.c b/drivers/usb/serial/safe_serial.c
index 96a1756..88bf14a 100644
--- a/drivers/usb/serial/safe_serial.c
+++ b/drivers/usb/serial/safe_serial.c
@@ -92,7 +92,7 @@ MODULE_DESCRIPTION (DRIVER_DESC);
 MODULE_LICENSE("GPL");
 
 #if defined(CONFIG_USBD_SAFE_SERIAL_VENDOR) && !defined(CONFIG_USBD_SAFE_SERIAL_PRODUCT)
-#abort "SAFE_SERIAL_VENDOR defined without SAFE_SERIAL_PRODUCT"
+#error "SAFE_SERIAL_VENDOR defined without SAFE_SERIAL_PRODUCT"
 #endif
 
 #if ! defined(CONFIG_USBD_SAFE_SERIAL_VENDOR)
-- 
cgit v1.1


From d40ece1dc8dcc89ab921755cbc93a5cfb46d0766 Mon Sep 17 00:00:00 2001
From: Borislav Petkov <bbpetkov@yahoo.de>
Date: Wed, 28 Sep 2005 18:06:04 +0200
Subject: [PATCH] USB: make usb storage note visible in Kconfig

the following patch splits the NOTE: in the Device Drivers->USB submenu of
Kconfig thus making the whole of it readable on 600x800 terminals.
(Otherwise, the line was too big and disappeared into nowhere.)

Signed-off-by: Borislav Petkov <petkov@uni-muenster.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/storage/Kconfig |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
---
 drivers/usb/storage/Kconfig | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

(limited to 'drivers')

diff --git a/drivers/usb/storage/Kconfig b/drivers/usb/storage/Kconfig
index bb9819c..1a9679f 100644
--- a/drivers/usb/storage/Kconfig
+++ b/drivers/usb/storage/Kconfig
@@ -2,7 +2,8 @@
 # USB Storage driver configuration
 #
 
-comment "NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information"
+comment "NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'"
+comment "may also be needed; see USB_STORAGE Help for more information"
 	depends on USB
 
 config USB_STORAGE
-- 
cgit v1.1


From a8798533c1f876b97566588cf2bf52458cb4a35d Mon Sep 17 00:00:00 2001
From: Daniel Drake <dsd@gentoo.org>
Date: Thu, 29 Sep 2005 00:14:21 +0100
Subject: [PATCH] USB Storage: HP8200: Another device type detection fix

There appears to be one more case where the HP8200 CD writer devices are
detected as flash readers - when the USB cable is replugged after use, with
the power cable still connected.

Oddly enough, the identify device command appears to 'fall through' when the
devices are in this state, the status register reading exactly the same opcode
as the command (0xA1) that was just executed.

I think it's safe to label this behaviour as specific to HP8200 devices, I
can't get the flash devices to respond like this.

This patch should solve the last of the HP8200 issues which have cropped up
recently.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/storage/shuttle_usbat.c |   12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
---
 drivers/usb/storage/shuttle_usbat.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/storage/shuttle_usbat.c b/drivers/usb/storage/shuttle_usbat.c
index 356342c..bd448d6 100644
--- a/drivers/usb/storage/shuttle_usbat.c
+++ b/drivers/usb/storage/shuttle_usbat.c
@@ -855,15 +855,15 @@ static int usbat_identify_device(struct us_data *us,
  	if (rc != USB_STOR_XFER_GOOD)
  		return USB_STOR_TRANSPORT_ERROR;
 
-	// Check for error bit
-	if (status & 0x01) {
-		 // Device is a CompactFlash reader/writer
-		US_DEBUGP("usbat_identify_device: Detected Flash reader/writer\n");
-		info->devicetype = USBAT_DEV_FLASH;
-	} else {
+	// Check for error bit, or if the command 'fell through'
+	if (status == 0xA1 || !(status & 0x01)) {
 		// Device is HP 8200
 		US_DEBUGP("usbat_identify_device: Detected HP8200 CDRW\n");
 		info->devicetype = USBAT_DEV_HP8200;
+	} else {
+		// Device is a CompactFlash reader/writer
+		US_DEBUGP("usbat_identify_device: Detected Flash reader/writer\n");
+		info->devicetype = USBAT_DEV_FLASH;
 	}
 
 	return USB_STOR_TRANSPORT_GOOD;
-- 
cgit v1.1


From b7b1e65588b8576c66a429a2623c91504efcf751 Mon Sep 17 00:00:00 2001
From: Daniel Drake <dsd@gentoo.org>
Date: Fri, 30 Sep 2005 12:49:36 +0100
Subject: [PATCH] usb-storage: Some minor shuttle_usbat cleanups

A while ago, Matthew Dharm wrote:
> Looks good.  Tho, I would like to see a future patch to do two things:
> 	1) Change comments from C++ style to C-style
> 	2) Make sure we're naming consistently everywhere SCM, USBAT,
> 	USBAT-02 (most noticably needing fixing is the string used at
> 	transport-selection time, but a sweep of all uses to be consistent
> 	would be in order).

Sorry for the long delay, here is a patch to address this. I also clarified
some ATA/ATAPI wording + function names.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/storage/shuttle_usbat.c |  306 ++++++++++++++++++++----------------
 drivers/usb/storage/shuttle_usbat.h |   66 +++----
 drivers/usb/storage/transport.h     |    2
 drivers/usb/storage/unusual_devs.h  |   10 -
 drivers/usb/storage/usb.c           |    4
 5 files changed, 213 insertions(+), 175 deletions(-)
---
 drivers/usb/storage/shuttle_usbat.c | 306 ++++++++++++++++++++----------------
 drivers/usb/storage/shuttle_usbat.h |  66 ++++----
 drivers/usb/storage/transport.h     |   2 +-
 drivers/usb/storage/unusual_devs.h  |  10 +-
 drivers/usb/storage/usb.c           |   4 +-
 5 files changed, 213 insertions(+), 175 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/storage/shuttle_usbat.c b/drivers/usb/storage/shuttle_usbat.c
index bd448d6..33c55a6 100644
--- a/drivers/usb/storage/shuttle_usbat.c
+++ b/drivers/usb/storage/shuttle_usbat.c
@@ -1,4 +1,4 @@
-/* Driver for SCM Microsystems USB-ATAPI cable
+/* Driver for SCM Microsystems (a.k.a. Shuttle) USB-ATAPI cable
  *
  * $Id: shuttle_usbat.c,v 1.17 2002/04/22 03:39:43 mdharm Exp $
  *
@@ -67,10 +67,10 @@ static int usbat_flash_transport(struct scsi_cmnd * srb, struct us_data *us);
 static int usbat_hp8200e_transport(struct scsi_cmnd *srb, struct us_data *us);
 
 /*
- * Convenience function to produce an ATAPI read/write sectors command
+ * Convenience function to produce an ATA read/write sectors command
  * Use cmd=0x20 for read, cmd=0x30 for write
  */
-static void usbat_pack_atapi_sector_cmd(unsigned char *buf,
+static void usbat_pack_ata_sector_cmd(unsigned char *buf,
 					unsigned char thistime,
 					u32 sector, unsigned char cmd)
 {
@@ -196,10 +196,12 @@ static int usbat_check_status(struct us_data *us)
 	if (rc != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_FAILED;
 
-	if (*reply & 0x01 && *reply != 0x51) // error/check condition (0x51 is ok)
+	/* error/check condition (0x51 is ok) */
+	if (*reply & 0x01 && *reply != 0x51)
 		return USB_STOR_TRANSPORT_FAILED;
 
-	if (*reply & 0x20) // device fault
+	/* device fault */
+	if (*reply & 0x20)
 		return USB_STOR_TRANSPORT_FAILED;
 
 	return USB_STOR_TRANSPORT_GOOD;
@@ -222,29 +224,39 @@ static int usbat_set_shuttle_features(struct us_data *us,
 	command[0] = 0x40;
 	command[1] = USBAT_CMD_SET_FEAT;
 
-	// The only bit relevant to ATA access is bit 6
-	// which defines 8 bit data access (set) or 16 bit (unset)
+	/*
+	 * The only bit relevant to ATA access is bit 6
+	 * which defines 8 bit data access (set) or 16 bit (unset)
+	 */
 	command[2] = epp_control;
 
-	// If FCQ is set in the qualifier (defined in R/W cmd), then bits U0, U1,
-	// ET1 and ET2 define an external event to be checked for on event of a
-	// _read_blocks or _write_blocks operation. The read/write will not take
-	// place unless the defined trigger signal is active.
+	/*
+	 * If FCQ is set in the qualifier (defined in R/W cmd), then bits U0, U1,
+	 * ET1 and ET2 define an external event to be checked for on event of a
+	 * _read_blocks or _write_blocks operation. The read/write will not take
+	 * place unless the defined trigger signal is active.
+	 */
 	command[3] = external_trigger;
 
-	// The resultant byte of the mask operation (see mask_byte) is compared for
-	// equivalence with this test pattern. If equal, the read/write will take
-	// place.
+	/*
+	 * The resultant byte of the mask operation (see mask_byte) is compared for
+	 * equivalence with this test pattern. If equal, the read/write will take
+	 * place.
+	 */
 	command[4] = test_pattern;
 
-	// This value is logically ANDed with the status register field specified
-	// in the read/write command.
+	/*
+	 * This value is logically ANDed with the status register field specified
+	 * in the read/write command.
+	 */
 	command[5] = mask_byte;
 
-	// If ALQ is set in the qualifier, this field contains the address of the
-	// registers where the byte count should be read for transferring the data.
-	// If ALQ is not set, then this field contains the number of bytes to be
-	// transferred.
+	/*
+	 * If ALQ is set in the qualifier, this field contains the address of the
+	 * registers where the byte count should be read for transferring the data.
+	 * If ALQ is not set, then this field contains the number of bytes to be
+	 * transferred.
+	 */
 	command[6] = subcountL;
 	command[7] = subcountH;
 
@@ -273,26 +285,26 @@ static int usbat_wait_not_busy(struct us_data *us, int minutes)
 
 		if (result!=USB_STOR_XFER_GOOD)
 			return USB_STOR_TRANSPORT_ERROR;
-		if (*status & 0x01) { // check condition
+		if (*status & 0x01) { /* check condition */
 			result = usbat_read(us, USBAT_ATA, 0x10, status);
 			return USB_STOR_TRANSPORT_FAILED;
 		}
-		if (*status & 0x20) // device fault
+		if (*status & 0x20) /* device fault */
 			return USB_STOR_TRANSPORT_FAILED;
 
-		if ((*status & 0x80)==0x00) { // not busy
+		if ((*status & 0x80)==0x00) { /* not busy */
 			US_DEBUGP("Waited not busy for %d steps\n", i);
 			return USB_STOR_TRANSPORT_GOOD;
 		}
 
 		if (i<500)
-			msleep(10); // 5 seconds
+			msleep(10); /* 5 seconds */
 		else if (i<700)
-			msleep(50); // 10 seconds
+			msleep(50); /* 10 seconds */
 		else if (i<1200)
-			msleep(100); // 50 seconds
+			msleep(100); /* 50 seconds */
 		else
-			msleep(1000); // X minutes
+			msleep(1000); /* X minutes */
 	}
 
 	US_DEBUGP("Waited not busy for %d minutes, timing out.\n",
@@ -412,9 +424,12 @@ static int usbat_hp8200e_rw_block_test(struct us_data *us,
 
 		if (i==0) {
 			cmdlen = 16;
-			// Write to multiple registers
-			// Not really sure the 0x07, 0x17, 0xfc, 0xe7 is necessary here,
-			// but that's what came out of the trace every single time.
+			/*
+			 * Write to multiple registers
+			 * Not really sure the 0x07, 0x17, 0xfc, 0xe7 is
+			 * necessary here, but that's what came out of the
+			 * trace every single time.
+			 */
 			command[0] = 0x40;
 			command[1] = access | USBAT_CMD_WRITE_REGS;
 			command[2] = 0x07;
@@ -426,7 +441,7 @@ static int usbat_hp8200e_rw_block_test(struct us_data *us,
 		} else
 			cmdlen = 8;
 
-		// Conditionally read or write blocks
+		/* Conditionally read or write blocks */
 		command[cmdlen-8] = (direction==DMA_TO_DEVICE ? 0x40 : 0xC0);
 		command[cmdlen-7] = access |
 				(direction==DMA_TO_DEVICE ?
@@ -456,11 +471,6 @@ static int usbat_hp8200e_rw_block_test(struct us_data *us,
 
 		}
 
-
-		//US_DEBUGP("Transfer %s %d bytes, sg buffers %d\n",
-		//	direction == DMA_TO_DEVICE ? "out" : "in",
-		//	len, use_sg);
-
 		result = usb_stor_bulk_transfer_sg(us,
 			pipe, content, len, use_sg, NULL);
 
@@ -508,9 +518,9 @@ static int usbat_hp8200e_rw_block_test(struct us_data *us,
 
 			if (result!=USB_STOR_XFER_GOOD)
 				return USB_STOR_TRANSPORT_ERROR;
-			if (*status & 0x01) // check condition
+			if (*status & 0x01) /* check condition */
 				return USB_STOR_TRANSPORT_FAILED;
-			if (*status & 0x20) // device fault
+			if (*status & 0x20) /* device fault */
 				return USB_STOR_TRANSPORT_FAILED;
 
 			US_DEBUGP("Redoing %s\n",
@@ -547,32 +557,32 @@ static int usbat_multiple_write(struct us_data *us,
 
 	BUG_ON(num_registers > US_IOBUF_SIZE/2);
 
-	// Write to multiple registers, ATA access
+	/* Write to multiple registers, ATA access */
 	command[0] = 0x40;
 	command[1] = USBAT_ATA | USBAT_CMD_WRITE_REGS;
 
-	// No relevance
+	/* No relevance */
 	command[2] = 0;
 	command[3] = 0;
 	command[4] = 0;
 	command[5] = 0;
 
-	// Number of bytes to be transferred (incl. addresses and data)
+	/* Number of bytes to be transferred (incl. addresses and data) */
 	command[6] = LSB_of(num_registers*2);
 	command[7] = MSB_of(num_registers*2);
 
-	// The setup command
+	/* The setup command */
 	result = usbat_execute_command(us, command, 8);
 	if (result != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_ERROR;
 
-	// Create the reg/data, reg/data sequence
+	/* Create the reg/data, reg/data sequence */
 	for (i=0; i<num_registers; i++) {
 		data[i<<1] = registers[i];
 		data[1+(i<<1)] = data_out[i];
 	}
 
-	// Send the data
+	/* Send the data */
 	result = usbat_bulk_write(us, data, num_registers*2);
 	if (result != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_ERROR;
@@ -606,17 +616,17 @@ static int usbat_read_blocks(struct us_data *us,
 	command[1] = USBAT_ATA | USBAT_CMD_COND_READ_BLOCK;
 	command[2] = USBAT_ATA_DATA;
 	command[3] = USBAT_ATA_STATUS;
-	command[4] = 0xFD; // Timeout (ms);
+	command[4] = 0xFD; /* Timeout (ms); */
 	command[5] = USBAT_QUAL_FCQ;
 	command[6] = LSB_of(len);
 	command[7] = MSB_of(len);
 
-	// Multiple block read setup command
+	/* Multiple block read setup command */
 	result = usbat_execute_command(us, command, 8);
 	if (result != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_FAILED;
 	
-	// Read the blocks we just asked for
+	/* Read the blocks we just asked for */
 	result = usbat_bulk_read(us, buffer, len);
 	if (result != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_FAILED;
@@ -647,17 +657,17 @@ static int usbat_write_blocks(struct us_data *us,
 	command[1] = USBAT_ATA | USBAT_CMD_COND_WRITE_BLOCK;
 	command[2] = USBAT_ATA_DATA;
 	command[3] = USBAT_ATA_STATUS;
-	command[4] = 0xFD; // Timeout (ms)
+	command[4] = 0xFD; /* Timeout (ms) */
 	command[5] = USBAT_QUAL_FCQ;
 	command[6] = LSB_of(len);
 	command[7] = MSB_of(len);
 
-	// Multiple block write setup command
+	/* Multiple block write setup command */
 	result = usbat_execute_command(us, command, 8);
 	if (result != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_FAILED;
 	
-	// Write the data
+	/* Write the data */
 	result = usbat_bulk_write(us, buffer, len);
 	if (result != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_FAILED;
@@ -711,16 +721,20 @@ static int usbat_device_reset(struct us_data *us)
 {
 	int rc;
 
-	// Reset peripheral, enable peripheral control signals
-	// (bring reset signal up)
+	/*
+	 * Reset peripheral, enable peripheral control signals
+	 * (bring reset signal up)
+	 */
 	rc = usbat_write_user_io(us,
 							 USBAT_UIO_DRVRST | USBAT_UIO_OE1 | USBAT_UIO_OE0,
 							 USBAT_UIO_EPAD | USBAT_UIO_1);
 	if (rc != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_ERROR;
 			
-	// Enable peripheral control signals
-	// (bring reset signal down)
+	/*
+	 * Enable peripheral control signals
+	 * (bring reset signal down)
+	 */
 	rc = usbat_write_user_io(us,
 							 USBAT_UIO_OE1  | USBAT_UIO_OE0,
 							 USBAT_UIO_EPAD | USBAT_UIO_1);
@@ -737,7 +751,7 @@ static int usbat_device_enable_cdt(struct us_data *us)
 {
 	int rc;
 
-	// Enable peripheral control signals and card detect
+	/* Enable peripheral control signals and card detect */
 	rc = usbat_write_user_io(us,
 							 USBAT_UIO_ACKD | USBAT_UIO_OE1  | USBAT_UIO_OE0,
 							 USBAT_UIO_EPAD | USBAT_UIO_1);
@@ -786,7 +800,7 @@ static int usbat_flash_check_media(struct us_data *us,
 	if (rc != USB_STOR_XFER_GOOD)
 		return USB_STOR_TRANSPORT_ERROR;
 
-	// Check for media existence
+	/* Check for media existence */
 	rc = usbat_flash_check_media_present(uio);
 	if (rc == USBAT_FLASH_MEDIA_NONE) {
 		info->sense_key = 0x02;
@@ -795,11 +809,11 @@ static int usbat_flash_check_media(struct us_data *us,
 		return USB_STOR_TRANSPORT_FAILED;
 	}
 
-	// Check for media change
+	/* Check for media change */
 	rc = usbat_flash_check_media_changed(uio);
 	if (rc == USBAT_FLASH_MEDIA_CHANGED) {
 
-		// Reset and re-enable card detect
+		/* Reset and re-enable card detect */
 		rc = usbat_device_reset(us);
 		if (rc != USB_STOR_TRANSPORT_GOOD)
 			return rc;
@@ -855,13 +869,13 @@ static int usbat_identify_device(struct us_data *us,
  	if (rc != USB_STOR_XFER_GOOD)
  		return USB_STOR_TRANSPORT_ERROR;
 
-	// Check for error bit, or if the command 'fell through'
+	/* Check for error bit, or if the command 'fell through' */
 	if (status == 0xA1 || !(status & 0x01)) {
-		// Device is HP 8200
+		/* Device is HP 8200 */
 		US_DEBUGP("usbat_identify_device: Detected HP8200 CDRW\n");
 		info->devicetype = USBAT_DEV_HP8200;
 	} else {
-		// Device is a CompactFlash reader/writer
+		/* Device is a CompactFlash reader/writer */
 		US_DEBUGP("usbat_identify_device: Detected Flash reader/writer\n");
 		info->devicetype = USBAT_DEV_FLASH;
 	}
@@ -916,7 +930,7 @@ static int usbat_flash_get_sector_count(struct us_data *us,
 	if (!reply)
 		return USB_STOR_TRANSPORT_ERROR;
 
-	// ATAPI command : IDENTIFY DEVICE
+	/* ATA command : IDENTIFY DEVICE */
 	rc = usbat_multiple_write(us, registers, command, 3);
 	if (rc != USB_STOR_XFER_GOOD) {
 		US_DEBUGP("usbat_flash_get_sector_count: Gah! identify_device failed\n");
@@ -924,7 +938,7 @@ static int usbat_flash_get_sector_count(struct us_data *us,
 		goto leave;
 	}
 
-	// Read device status
+	/* Read device status */
 	if (usbat_get_status(us, &status) != USB_STOR_XFER_GOOD) {
 		rc = USB_STOR_TRANSPORT_ERROR;
 		goto leave;
@@ -932,7 +946,7 @@ static int usbat_flash_get_sector_count(struct us_data *us,
 
 	msleep(100);
 
-	// Read the device identification data
+	/* Read the device identification data */
 	rc = usbat_read_block(us, reply, 512);
 	if (rc != USB_STOR_TRANSPORT_GOOD)
 		goto leave;
@@ -977,19 +991,23 @@ static int usbat_flash_read_data(struct us_data *us,
 	if (result != USB_STOR_TRANSPORT_GOOD)
 		return result;
 
-	// we're working in LBA mode.  according to the ATA spec,
-	// we can support up to 28-bit addressing.  I don't know if Jumpshot
-	// supports beyond 24-bit addressing.  It's kind of hard to test
-	// since it requires > 8GB CF card.
+	/*
+	 * we're working in LBA mode.  according to the ATA spec,
+	 * we can support up to 28-bit addressing.  I don't know if Jumpshot
+	 * supports beyond 24-bit addressing.  It's kind of hard to test
+	 * since it requires > 8GB CF card.
+	 */
 
 	if (sector > 0x0FFFFFFF)
 		return USB_STOR_TRANSPORT_ERROR;
 
 	totallen = sectors * info->ssize;
 
-	// Since we don't read more than 64 KB at a time, we have to create
-	// a bounce buffer and move the data a piece at a time between the
-	// bounce buffer and the actual transfer buffer.
+	/*
+	 * Since we don't read more than 64 KB at a time, we have to create
+	 * a bounce buffer and move the data a piece at a time between the
+	 * bounce buffer and the actual transfer buffer.
+	 */
 
 	alloclen = min(totallen, 65536u);
 	buffer = kmalloc(alloclen, GFP_NOIO);
@@ -997,27 +1015,29 @@ static int usbat_flash_read_data(struct us_data *us,
 		return USB_STOR_TRANSPORT_ERROR;
 
 	do {
-		// loop, never allocate or transfer more than 64k at once
-		// (min(128k, 255*info->ssize) is the real limit)
+		/*
+		 * loop, never allocate or transfer more than 64k at once
+		 * (min(128k, 255*info->ssize) is the real limit)
+		 */
 		len = min(totallen, alloclen);
 		thistime = (len / info->ssize) & 0xff;
  
-		// ATAPI command 0x20 (READ SECTORS)
-		usbat_pack_atapi_sector_cmd(command, thistime, sector, 0x20);
+		/* ATA command 0x20 (READ SECTORS) */
+		usbat_pack_ata_sector_cmd(command, thistime, sector, 0x20);
 
-		// Write/execute ATAPI read command
+		/* Write/execute ATA read command */
 		result = usbat_multiple_write(us, registers, command, 7);
 		if (result != USB_STOR_TRANSPORT_GOOD)
 			goto leave;
 
-		// Read the data we just requested
+		/* Read the data we just requested */
 		result = usbat_read_blocks(us, buffer, len);
 		if (result != USB_STOR_TRANSPORT_GOOD)
 			goto leave;
   	 
 		US_DEBUGP("usbat_flash_read_data:  %d bytes\n", len);
 	
-		// Store the data in the transfer buffer
+		/* Store the data in the transfer buffer */
 		usb_stor_access_xfer_buf(buffer, len, us->srb,
 					 &sg_idx, &sg_offset, TO_XFER_BUF);
 
@@ -1061,19 +1081,23 @@ static int usbat_flash_write_data(struct us_data *us,
 	if (result != USB_STOR_TRANSPORT_GOOD)
 		return result;
 
-	// we're working in LBA mode.  according to the ATA spec,
-	// we can support up to 28-bit addressing.  I don't know if Jumpshot
-	// supports beyond 24-bit addressing.  It's kind of hard to test
-	// since it requires > 8GB CF card.
+	/*
+	 * we're working in LBA mode.  according to the ATA spec,
+	 * we can support up to 28-bit addressing.  I don't know if the device
+	 * supports beyond 24-bit addressing.  It's kind of hard to test
+	 * since it requires > 8GB media.
+	 */
 
 	if (sector > 0x0FFFFFFF)
 		return USB_STOR_TRANSPORT_ERROR;
 
 	totallen = sectors * info->ssize;
 
-	// Since we don't write more than 64 KB at a time, we have to create
-	// a bounce buffer and move the data a piece at a time between the
-	// bounce buffer and the actual transfer buffer.
+	/*
+	 * Since we don't write more than 64 KB at a time, we have to create
+	 * a bounce buffer and move the data a piece at a time between the
+	 * bounce buffer and the actual transfer buffer.
+	 */
 
 	alloclen = min(totallen, 65536u);
 	buffer = kmalloc(alloclen, GFP_NOIO);
@@ -1081,24 +1105,26 @@ static int usbat_flash_write_data(struct us_data *us,
 		return USB_STOR_TRANSPORT_ERROR;
 
 	do {
-		// loop, never allocate or transfer more than 64k at once
-		// (min(128k, 255*info->ssize) is the real limit)
+		/*
+		 * loop, never allocate or transfer more than 64k at once
+		 * (min(128k, 255*info->ssize) is the real limit)
+		 */
 		len = min(totallen, alloclen);
 		thistime = (len / info->ssize) & 0xff;
 
-		// Get the data from the transfer buffer
+		/* Get the data from the transfer buffer */
 		usb_stor_access_xfer_buf(buffer, len, us->srb,
 					 &sg_idx, &sg_offset, FROM_XFER_BUF);
 
-		// ATAPI command 0x30 (WRITE SECTORS)
-		usbat_pack_atapi_sector_cmd(command, thistime, sector, 0x30);		
+		/* ATA command 0x30 (WRITE SECTORS) */
+		usbat_pack_ata_sector_cmd(command, thistime, sector, 0x30);
 
-		// Write/execute ATAPI write command
+		/* Write/execute ATA write command */
 		result = usbat_multiple_write(us, registers, command, 7);
 		if (result != USB_STOR_TRANSPORT_GOOD)
 			goto leave;
 
-		// Write the data
+		/* Write the data */
 		result = usbat_write_blocks(us, buffer, len);
 		if (result != USB_STOR_TRANSPORT_GOOD)
 			goto leave;
@@ -1169,42 +1195,44 @@ static int usbat_hp8200e_handle_read10(struct us_data *us,
 			srb->transfersize);
 	}
 
-	// Since we only read in one block at a time, we have to create
-	// a bounce buffer and move the data a piece at a time between the
-	// bounce buffer and the actual transfer buffer.
+	/*
+	 * Since we only read in one block at a time, we have to create
+	 * a bounce buffer and move the data a piece at a time between the
+	 * bounce buffer and the actual transfer buffer.
+	 */
 
 	len = (65535/srb->transfersize) * srb->transfersize;
 	US_DEBUGP("Max read is %d bytes\n", len);
 	len = min(len, srb->request_bufflen);
 	buffer = kmalloc(len, GFP_NOIO);
-	if (buffer == NULL) // bloody hell!
+	if (buffer == NULL) /* bloody hell! */
 		return USB_STOR_TRANSPORT_FAILED;
 	sector = short_pack(data[7+3], data[7+2]);
 	sector <<= 16;
 	sector |= short_pack(data[7+5], data[7+4]);
 	transferred = 0;
 
-	sg_segment = 0; // for keeping track of where we are in
-	sg_offset = 0;  // the scatter/gather list
+	sg_segment = 0; /* for keeping track of where we are in */
+	sg_offset = 0;  /* the scatter/gather list */
 
 	while (transferred != srb->request_bufflen) {
 
 		if (len > srb->request_bufflen - transferred)
 			len = srb->request_bufflen - transferred;
 
-		data[3] = len&0xFF; 	  // (cylL) = expected length (L)
-		data[4] = (len>>8)&0xFF;  // (cylH) = expected length (H)
+		data[3] = len&0xFF; 	  /* (cylL) = expected length (L) */
+		data[4] = (len>>8)&0xFF;  /* (cylH) = expected length (H) */
 
-		// Fix up the SCSI command sector and num sectors
+		/* Fix up the SCSI command sector and num sectors */
 
-		data[7+2] = MSB_of(sector>>16); // SCSI command sector
+		data[7+2] = MSB_of(sector>>16); /* SCSI command sector */
 		data[7+3] = LSB_of(sector>>16);
 		data[7+4] = MSB_of(sector&0xFFFF);
 		data[7+5] = LSB_of(sector&0xFFFF);
 		if (data[7+0] == GPCMD_READ_CD)
 			data[7+6] = 0;
-		data[7+7] = MSB_of(len / srb->transfersize); // SCSI command
-		data[7+8] = LSB_of(len / srb->transfersize); // num sectors
+		data[7+7] = MSB_of(len / srb->transfersize); /* SCSI command */
+		data[7+8] = LSB_of(len / srb->transfersize); /* num sectors */
 
 		result = usbat_hp8200e_rw_block_test(us, USBAT_ATA, 
 			registers, data, 19,
@@ -1217,16 +1245,16 @@ static int usbat_hp8200e_handle_read10(struct us_data *us,
 		if (result != USB_STOR_TRANSPORT_GOOD)
 			break;
 
-		// Store the data in the transfer buffer
+		/* Store the data in the transfer buffer */
 		usb_stor_access_xfer_buf(buffer, len, srb,
 				 &sg_segment, &sg_offset, TO_XFER_BUF);
 
-		// Update the amount transferred and the sector number
+		/* Update the amount transferred and the sector number */
 
 		transferred += len;
 		sector += len / srb->transfersize;
 
-	} // while transferred != srb->request_bufflen
+	} /* while transferred != srb->request_bufflen */
 
 	kfree(buffer);
 	return result;
@@ -1237,7 +1265,7 @@ static int usbat_select_and_test_registers(struct us_data *us)
 	int selector;
 	unsigned char *status = us->iobuf;
 
-	// try device = master, then device = slave.
+	/* try device = master, then device = slave. */
 	for (selector = 0xA0; selector <= 0xB0; selector += 0x10) {
 		if (usbat_write(us, USBAT_ATA, USBAT_ATA_DEVICE, selector) !=
 				USB_STOR_XFER_GOOD)
@@ -1298,7 +1326,7 @@ int init_usbat(struct us_data *us)
 	memset(us->extra, 0, sizeof(struct usbat_info));
 	info = (struct usbat_info *) (us->extra);
 
-	// Enable peripheral control signals
+	/* Enable peripheral control signals */
 	rc = usbat_write_user_io(us,
 				 USBAT_UIO_OE1 | USBAT_UIO_OE0,
 				 USBAT_UIO_EPAD | USBAT_UIO_1);
@@ -1337,7 +1365,7 @@ int init_usbat(struct us_data *us)
 
 	US_DEBUGP("INIT 5\n");
 
-	// Enable peripheral control signals and card detect
+	/* Enable peripheral control signals and card detect */
 	rc = usbat_device_enable_cdt(us);
 	if (rc != USB_STOR_TRANSPORT_GOOD)
 		return rc;
@@ -1364,7 +1392,7 @@ int init_usbat(struct us_data *us)
 
 	US_DEBUGP("INIT 9\n");
 
-	// At this point, we need to detect which device we are using
+	/* At this point, we need to detect which device we are using */
 	if (usbat_set_transport(us, info))
 		return USB_STOR_TRANSPORT_ERROR;
 
@@ -1414,10 +1442,10 @@ static int usbat_hp8200e_transport(struct scsi_cmnd *srb, struct us_data *us)
 	data[0] = 0x00;
 	data[1] = 0x00;
 	data[2] = 0x00;
-	data[3] = len&0xFF; 		// (cylL) = expected length (L)
-	data[4] = (len>>8)&0xFF; 	// (cylH) = expected length (H)
-	data[5] = 0xB0; 		// (device sel) = slave
-	data[6] = 0xA0; 		// (command) = ATA PACKET COMMAND
+	data[3] = len&0xFF; 		/* (cylL) = expected length (L) */
+	data[4] = (len>>8)&0xFF; 	/* (cylH) = expected length (H) */
+	data[5] = 0xB0; 		/* (device sel) = slave */
+	data[6] = 0xA0; 		/* (command) = ATA PACKET COMMAND */
 
 	for (i=7; i<19; i++) {
 		registers[i] = 0x10;
@@ -1466,13 +1494,15 @@ static int usbat_hp8200e_transport(struct scsi_cmnd *srb, struct us_data *us)
 		return result;
 	}
 
-	// Write the 12-byte command header.
-
-	// If the command is BLANK then set the timer for 75 minutes.
-	// Otherwise set it for 10 minutes.
-
-	// NOTE: THE 8200 DOCUMENTATION STATES THAT BLANKING A CDRW
-	// AT SPEED 4 IS UNRELIABLE!!!
+	/*
+	 * Write the 12-byte command header.
+	 *
+	 * If the command is BLANK then set the timer for 75 minutes.
+	 * Otherwise set it for 10 minutes.
+	 *
+	 * NOTE: THE 8200 DOCUMENTATION STATES THAT BLANKING A CDRW
+	 * AT SPEED 4 IS UNRELIABLE!!!
+	 */
 
 	if ( (result = usbat_write_block(us, 
 			USBAT_ATA, srb->cmnd, 12,
@@ -1481,19 +1511,18 @@ static int usbat_hp8200e_transport(struct scsi_cmnd *srb, struct us_data *us)
 		return result;
 	}
 
-	// If there is response data to be read in 
-	// then do it here.
+	/* If there is response data to be read in then do it here. */
 
 	if (len != 0 && (srb->sc_data_direction == DMA_FROM_DEVICE)) {
 
-		// How many bytes to read in? Check cylL register
+		/* How many bytes to read in? Check cylL register */
 
 		if (usbat_read(us, USBAT_ATA, USBAT_ATA_LBA_ME, status) != 
 		    	USB_STOR_XFER_GOOD) {
 			return USB_STOR_TRANSPORT_ERROR;
 		}
 
-		if (len > 0xFF) { // need to read cylH also
+		if (len > 0xFF) { /* need to read cylH also */
 			len = *status;
 			if (usbat_read(us, USBAT_ATA, USBAT_ATA_LBA_HI, status) !=
 				    USB_STOR_XFER_GOOD) {
@@ -1556,13 +1585,16 @@ static int usbat_flash_transport(struct scsi_cmnd * srb, struct us_data *us)
 		if (rc != USB_STOR_TRANSPORT_GOOD)
 			return rc;
 
-		info->ssize = 0x200;  // hard coded 512 byte sectors as per ATA spec
+		/* hard coded 512 byte sectors as per ATA spec */
+		info->ssize = 0x200;
 		US_DEBUGP("usbat_flash_transport: READ_CAPACITY: %ld sectors, %ld bytes per sector\n",
 			  info->sectors, info->ssize);
 
-		// build the reply
-		// note: must return the sector number of the last sector,
-		// *not* the total number of sectors
+		/*
+		 * build the reply
+		 * note: must return the sector number of the last sector,
+		 * *not* the total number of sectors
+		 */
 		((__be32 *) ptr)[0] = cpu_to_be32(info->sectors - 1);
 		((__be32 *) ptr)[1] = cpu_to_be32(info->ssize);
 		usb_stor_set_xfer_buf(ptr, 8, srb);
@@ -1586,7 +1618,9 @@ static int usbat_flash_transport(struct scsi_cmnd * srb, struct us_data *us)
 	}
 
 	if (srb->cmnd[0] == READ_12) {
-		// I don't think we'll ever see a READ_12 but support it anyway...
+		/*
+		 * I don't think we'll ever see a READ_12 but support it anyway
+		 */
 		block = ((u32)(srb->cmnd[2]) << 24) | ((u32)(srb->cmnd[3]) << 16) |
 		        ((u32)(srb->cmnd[4]) <<  8) | ((u32)(srb->cmnd[5]));
 
@@ -1608,7 +1642,9 @@ static int usbat_flash_transport(struct scsi_cmnd * srb, struct us_data *us)
 	}
 
 	if (srb->cmnd[0] == WRITE_12) {
-		// I don't think we'll ever see a WRITE_12 but support it anyway...
+		/*
+		 * I don't think we'll ever see a WRITE_12 but support it anyway
+		 */
 		block = ((u32)(srb->cmnd[2]) << 24) | ((u32)(srb->cmnd[3]) << 16) |
 		        ((u32)(srb->cmnd[4]) <<  8) | ((u32)(srb->cmnd[5]));
 
@@ -1645,8 +1681,10 @@ static int usbat_flash_transport(struct scsi_cmnd * srb, struct us_data *us)
 	}
 
 	if (srb->cmnd[0] == ALLOW_MEDIUM_REMOVAL) {
-		// sure.  whatever.  not like we can stop the user from popping
-		// the media out of the device (no locking doors, etc)
+		/*
+		 * sure.  whatever.  not like we can stop the user from popping
+		 * the media out of the device (no locking doors, etc)
+		 */
 		return USB_STOR_TRANSPORT_GOOD;
 	}
 
diff --git a/drivers/usb/storage/shuttle_usbat.h b/drivers/usb/storage/shuttle_usbat.h
index 5b8e867..25e7d8b 100644
--- a/drivers/usb/storage/shuttle_usbat.h
+++ b/drivers/usb/storage/shuttle_usbat.h
@@ -55,8 +55,8 @@
 #define USBAT_UIO_WRITE	0
 
 /* Qualifier bits */
-#define USBAT_QUAL_FCQ	0x20 // full compare
-#define USBAT_QUAL_ALQ	0x10 // auto load subcount
+#define USBAT_QUAL_FCQ	0x20	/* full compare */
+#define USBAT_QUAL_ALQ	0x10	/* auto load subcount */
 
 /* USBAT Flash Media status types */
 #define USBAT_FLASH_MEDIA_NONE	0
@@ -67,39 +67,39 @@
 #define USBAT_FLASH_MEDIA_CHANGED	1
 
 /* USBAT ATA registers */
-#define USBAT_ATA_DATA      0x10  // read/write data (R/W)
-#define USBAT_ATA_FEATURES  0x11  // set features (W)
-#define USBAT_ATA_ERROR     0x11  // error (R)
-#define USBAT_ATA_SECCNT    0x12  // sector count (R/W)
-#define USBAT_ATA_SECNUM    0x13  // sector number (R/W)
-#define USBAT_ATA_LBA_ME    0x14  // cylinder low (R/W)
-#define USBAT_ATA_LBA_HI    0x15  // cylinder high (R/W)
-#define USBAT_ATA_DEVICE    0x16  // head/device selection (R/W)
-#define USBAT_ATA_STATUS    0x17  // device status (R)
-#define USBAT_ATA_CMD       0x17  // device command (W)
-#define USBAT_ATA_ALTSTATUS 0x0E  // status (no clear IRQ) (R)
+#define USBAT_ATA_DATA      0x10  /* read/write data (R/W) */
+#define USBAT_ATA_FEATURES  0x11  /* set features (W) */
+#define USBAT_ATA_ERROR     0x11  /* error (R) */
+#define USBAT_ATA_SECCNT    0x12  /* sector count (R/W) */
+#define USBAT_ATA_SECNUM    0x13  /* sector number (R/W) */
+#define USBAT_ATA_LBA_ME    0x14  /* cylinder low (R/W) */
+#define USBAT_ATA_LBA_HI    0x15  /* cylinder high (R/W) */
+#define USBAT_ATA_DEVICE    0x16  /* head/device selection (R/W) */
+#define USBAT_ATA_STATUS    0x17  /* device status (R) */
+#define USBAT_ATA_CMD       0x17  /* device command (W) */
+#define USBAT_ATA_ALTSTATUS 0x0E  /* status (no clear IRQ) (R) */
 
 /* USBAT User I/O Data registers */
-#define USBAT_UIO_EPAD		0x80 // Enable Peripheral Control Signals
-#define USBAT_UIO_CDT		0x40 // Card Detect (Read Only)
-				     // CDT = ACKD & !UI1 & !UI0
-#define USBAT_UIO_1		0x20 // I/O 1
-#define USBAT_UIO_0		0x10 // I/O 0
-#define USBAT_UIO_EPP_ATA	0x08 // 1=EPP mode, 0=ATA mode
-#define USBAT_UIO_UI1		0x04 // Input 1
-#define USBAT_UIO_UI0		0x02 // Input 0
-#define USBAT_UIO_INTR_ACK	0x01 // Interrupt (ATA & ISA)/Acknowledge (EPP)
+#define USBAT_UIO_EPAD		0x80 /* Enable Peripheral Control Signals */
+#define USBAT_UIO_CDT		0x40 /* Card Detect (Read Only) */
+				     /* CDT = ACKD & !UI1 & !UI0 */
+#define USBAT_UIO_1		0x20 /* I/O 1 */
+#define USBAT_UIO_0		0x10 /* I/O 0 */
+#define USBAT_UIO_EPP_ATA	0x08 /* 1=EPP mode, 0=ATA mode */
+#define USBAT_UIO_UI1		0x04 /* Input 1 */
+#define USBAT_UIO_UI0		0x02 /* Input 0 */
+#define USBAT_UIO_INTR_ACK	0x01 /* Interrupt (ATA/ISA)/Acknowledge (EPP) */
 
 /* USBAT User I/O Enable registers */
-#define USBAT_UIO_DRVRST	0x80 // Reset Peripheral
-#define USBAT_UIO_ACKD		0x40 // Enable Card Detect
-#define USBAT_UIO_OE1		0x20 // I/O 1 set=output/clr=input
-				     // If ACKD=1, set OE1 to 1 also.
-#define USBAT_UIO_OE0		0x10 // I/O 0 set=output/clr=input
-#define USBAT_UIO_ADPRST	0x01 // Reset SCM chip
+#define USBAT_UIO_DRVRST	0x80 /* Reset Peripheral */
+#define USBAT_UIO_ACKD		0x40 /* Enable Card Detect */
+#define USBAT_UIO_OE1		0x20 /* I/O 1 set=output/clr=input */
+				     /* If ACKD=1, set OE1 to 1 also. */
+#define USBAT_UIO_OE0		0x10 /* I/O 0 set=output/clr=input */
+#define USBAT_UIO_ADPRST	0x01 /* Reset SCM chip */
 
 /* USBAT Features */
-#define USBAT_FEAT_ETEN	0x80 // External trigger enable
+#define USBAT_FEAT_ETEN	0x80	/* External trigger enable */
 #define USBAT_FEAT_U1	0x08
 #define USBAT_FEAT_U0	0x04
 #define USBAT_FEAT_ET1	0x02
@@ -112,12 +112,12 @@ struct usbat_info {
 	int devicetype;
 
 	/* Used for Flash readers only */
-	unsigned long sectors;     // total sector count
-	unsigned long ssize;       // sector size in bytes
+	unsigned long sectors;     /* total sector count */
+	unsigned long ssize;       /* sector size in bytes */
 
 	unsigned char sense_key;
-	unsigned long sense_asc;   // additional sense code
-	unsigned long sense_ascq;  // additional sense code qualifier
+	unsigned long sense_asc;   /* additional sense code */
+	unsigned long sense_ascq;  /* additional sense code qualifier */
 };
 
 #endif
diff --git a/drivers/usb/storage/transport.h b/drivers/usb/storage/transport.h
index 8d9e066..0a362cc 100644
--- a/drivers/usb/storage/transport.h
+++ b/drivers/usb/storage/transport.h
@@ -50,7 +50,7 @@
 #define US_PR_CB	0x01		/* Control/Bulk w/o interrupt */
 #define US_PR_BULK	0x50		/* bulk only */
 #ifdef CONFIG_USB_STORAGE_USBAT
-#define US_PR_SCM_ATAPI	0x80		/* SCM-ATAPI bridge */
+#define US_PR_USBAT	0x80		/* SCM-ATAPI bridge */
 #endif
 #ifdef CONFIG_USB_STORAGE_SDDR09
 #define US_PR_EUSB_SDDR09	0x81	/* SCM-SCSI bridge for SDDR-09 */
diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index b79dad1..71d051d 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -71,12 +71,12 @@ UNUSUAL_DEV(  0x03f0, 0x0107, 0x0200, 0x0200,
 UNUSUAL_DEV(  0x03f0, 0x0207, 0x0001, 0x0001, 
 		"HP",
 		"CD-Writer+ 8200e",
-		US_SC_8070, US_PR_SCM_ATAPI, init_usbat, 0), 
+		US_SC_8070, US_PR_USBAT, init_usbat, 0),
 
 UNUSUAL_DEV(  0x03f0, 0x0307, 0x0001, 0x0001, 
 		"HP",
 		"CD-Writer+ CD-4e",
-		US_SC_8070, US_PR_SCM_ATAPI, init_usbat, 0), 
+		US_SC_8070, US_PR_USBAT, init_usbat, 0),
 #endif
 
 /* Patch submitted by Mihnea-Costin Grigore <mihnea@zulu.ro> */
@@ -333,9 +333,9 @@ UNUSUAL_DEV(  0x04fc, 0x80c2, 0x0100, 0x0100,
 
 #ifdef CONFIG_USB_STORAGE_USBAT
 UNUSUAL_DEV(  0x04e6, 0x1010, 0x0000, 0x9999,
-		"SCM",
-		"SCM USBAT-02",
-		US_SC_SCSI, US_PR_SCM_ATAPI, init_usbat,
+		"Shuttle/SCM",
+		"USBAT-02",
+		US_SC_SCSI, US_PR_USBAT, init_usbat,
 		US_FL_SINGLE_LUN),
 #endif
 
diff --git a/drivers/usb/storage/usb.c b/drivers/usb/storage/usb.c
index f9a9bfa..5164900 100644
--- a/drivers/usb/storage/usb.c
+++ b/drivers/usb/storage/usb.c
@@ -555,8 +555,8 @@ static int get_transport(struct us_data *us)
 		break;
 
 #ifdef CONFIG_USB_STORAGE_USBAT
-	case US_PR_SCM_ATAPI:
-		us->transport_name = "SCM/ATAPI";
+	case US_PR_USBAT:
+		us->transport_name = "Shuttle USBAT";
 		us->transport = usbat_transport;
 		us->transport_reset = usb_stor_CB_reset;
 		us->max_lun = 1;
-- 
cgit v1.1


From 094ec604721ed2a9a7ed6dfe40fd699b2f53a4c3 Mon Sep 17 00:00:00 2001
From: Daniel Drake <dsd@gentoo.org>
Date: Fri, 30 Sep 2005 12:58:13 +0100
Subject: [PATCH] usb-storage: Readd missing SDDR-05b unusual_devs entry

Just noticed that the SDDR-05b entry is missing for the shuttle_usbat driver.
Looking through BK history it was removed in this patch:

http://linux.bkbits.net:8080/linux-2.6/gnupatch@42435730FZQ2XCA6Qv5GPGD4pC4laQ

However, at merge time, it looks like the duplicate was already removed,
compare these two revisions:

http://linux.bkbits.net:8080/linux-2.6/anno/drivers/usb/storage/unusual_devs.h@1.152
http://linux.bkbits.net:8080/linux-2.6/anno/drivers/usb/storage/unusual_devs.h@1.153

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/storage/unusual_devs.h |    8 ++++++++
 1 file changed, 8 insertions(+)
---
 drivers/usb/storage/unusual_devs.h | 8 ++++++++
 1 file changed, 8 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index 71d051d..ee9f050 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -702,6 +702,14 @@ UNUSUAL_DEV(  0x0781, 0x0001, 0x0200, 0x0200,
 		US_SC_SCSI, US_PR_CB, NULL,
 		US_FL_SINGLE_LUN ),
 
+#ifdef CONFIG_USB_STORAGE_USBAT
+UNUSUAL_DEV(  0x0781, 0x0005, 0x0005, 0x0005,
+		"Sandisk",
+		"ImageMate SDDR-05b",
+		US_SC_SCSI, US_PR_USBAT, init_usbat,
+		US_FL_SINGLE_LUN ),
+#endif
+
 UNUSUAL_DEV(  0x0781, 0x0100, 0x0100, 0x0100,
 		"Sandisk",
 		"ImageMate SDDR-12",
-- 
cgit v1.1


From e4a16e0c10a272e53c4a129b155dd711196b1d93 Mon Sep 17 00:00:00 2001
From: Phil Dibowitz <phil@ipom.com>
Date: Fri, 30 Sep 2005 00:20:15 -0700
Subject: [PATCH] Add unusual_dev for iBeat

This patch adds the US_FL_IGNORE_RESIDUE flag for the TrekStor i.Beat
Joy 2.0. Original version of this patch was sent by Stefan Werner
<dustbln@gmx.de> with test/rediff/etc. by me.

Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/storage/unusual_devs.h |    7 +++++++
 1 file changed, 7 insertions(+)
---
 drivers/usb/storage/unusual_devs.h | 7 +++++++
 1 file changed, 7 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index ee9f050..730ba8d 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -106,6 +106,13 @@ UNUSUAL_DEV(  0x0411, 0x001c, 0x0113, 0x0113,
 		US_SC_DEVICE, US_PR_DEVICE, NULL,
 		US_FL_FIX_INQUIRY ),
 
+/* Reported by Stefan Werner <dustbln@gmx.de> */
+UNUSUAL_DEV(  0x0419, 0xaaf6, 0x0100, 0x0100,
+		"TrekStor",
+		"i.Beat Joy 2.0",
+		US_SC_DEVICE, US_PR_DEVICE, NULL,
+		US_FL_IGNORE_RESIDUE ),
+
 /* Reported by Olaf Hering <olh@suse.de> from novell bug #105878 */
 UNUSUAL_DEV(  0x0424, 0x0fdc, 0x0210, 0x0210,
 		"SMSC",
-- 
cgit v1.1


From 880a9b5e7f70632ab60131ce3027da1c63fcd39e Mon Sep 17 00:00:00 2001
From: Phil Dibowitz <phil@ipom.com>
Date: Fri, 30 Sep 2005 00:27:36 -0700
Subject: [PATCH] Add unusual_devs for iPod Nano

This adds US_FL_FIX_CAPACITY for yet _another_ entire block of Apple
productIds. They really can't seem to get this right. This one is for
the iPod Nano. Reported by Tyson Vinson <lornoss@gmail.com>.

Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/storage/unusual_devs.h |   10 ++++++++++
 1 file changed, 10 insertions(+)
---
 drivers/usb/storage/unusual_devs.h | 10 ++++++++++
 1 file changed, 10 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index 730ba8d..a117018 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -605,6 +605,16 @@ UNUSUAL_DEV( 0x05ac, 0x1205, 0x0000, 0x9999,
 		US_SC_DEVICE, US_PR_DEVICE, NULL,
 		US_FL_FIX_CAPACITY ),
 
+/*
+ * Reported by Tyson Vinson <lornoss@gmail.com>
+ * This particular productId is the iPod Nano
+ */
+UNUSUAL_DEV( 0x05ac, 0x120a, 0x0000, 0x9999,
+		"Apple",
+		"iPod",
+		US_SC_DEVICE, US_PR_DEVICE, NULL,
+		US_FL_FIX_CAPACITY ),
+
 #ifdef CONFIG_USB_STORAGE_JUMPSHOT
 UNUSUAL_DEV(  0x05dc, 0x0001, 0x0000, 0x0001,
 		"Lexar",
-- 
cgit v1.1


From 3f8c03ee05801bf8539dd136d9246a416c45052a Mon Sep 17 00:00:00 2001
From: Daniel Ritz <daniel.ritz@gmx.ch>
Date: Wed, 28 Sep 2005 21:30:12 +0200
Subject: [PATCH] usb/input/touchkit: add more device IDs

add two more device IDs from eGalax' programming guide.
thanks to Jonathan Hopper <jrhopper () gmail ! com>  for pointing out.

Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

 drivers/usb/input/touchkitusb.c |    2 ++
 1 file changed, 2 insertions(+)
---
 drivers/usb/input/touchkitusb.c | 2 ++
 1 file changed, 2 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/input/touchkitusb.c b/drivers/usb/input/touchkitusb.c
index 3766ccc..0043e6e 100644
--- a/drivers/usb/input/touchkitusb.c
+++ b/drivers/usb/input/touchkitusb.c
@@ -75,7 +75,9 @@ struct touchkit_usb {
 
 static struct usb_device_id touchkit_devices[] = {
 	{USB_DEVICE(0x3823, 0x0001)},
+	{USB_DEVICE(0x0123, 0x0001)},
 	{USB_DEVICE(0x0eef, 0x0001)},
+	{USB_DEVICE(0x0eef, 0x0002)},
 	{}
 };
 
-- 
cgit v1.1


From a922c68732725866c88457026cf06a7620846506 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Thu, 6 Oct 2005 16:38:45 -0400
Subject: [PATCH] g_file_storage: fix obscure race condition

This patch (as575) fixes an unlikely race in the g_file_storage driver.
The problem can occur only when the driver is unbound before its
initialization routine has finished.

I also took the opportunity to replace kmalloc/memset with kzalloc.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/gadget/file_storage.c | 21 +++++++++------------
 1 file changed, 9 insertions(+), 12 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/gadget/file_storage.c b/drivers/usb/gadget/file_storage.c
index 241c570..86a6aeb 100644
--- a/drivers/usb/gadget/file_storage.c
+++ b/drivers/usb/gadget/file_storage.c
@@ -3823,12 +3823,11 @@ static int __init fsg_bind(struct usb_gadget *gadget)
 
 	/* Create the LUNs, open their backing files, and register the
 	 * LUN devices in sysfs. */
-	fsg->luns = kmalloc(i * sizeof(struct lun), GFP_KERNEL);
+	fsg->luns = kzalloc(i * sizeof(struct lun), GFP_KERNEL);
 	if (!fsg->luns) {
 		rc = -ENOMEM;
 		goto out;
 	}
-	memset(fsg->luns, 0, i * sizeof(struct lun));
 	fsg->nluns = i;
 
 	for (i = 0; i < fsg->nluns; ++i) {
@@ -3989,6 +3988,11 @@ static int __init fsg_bind(struct usb_gadget *gadget)
 			mod_data.removable, mod_data.can_stall,
 			mod_data.buflen);
 	DBG(fsg, "I/O thread pid: %d\n", fsg->thread_task->pid);
+
+	set_bit(REGISTERED, &fsg->atomic_bitflags);
+
+	/* Tell the thread to start working */
+	wake_up_process(fsg->thread_task);
 	return 0;
 
 autoconf_fail:
@@ -4051,10 +4055,9 @@ static int __init fsg_alloc(void)
 {
 	struct fsg_dev		*fsg;
 
-	fsg = kmalloc(sizeof *fsg, GFP_KERNEL);
+	fsg = kzalloc(sizeof *fsg, GFP_KERNEL);
 	if (!fsg)
 		return -ENOMEM;
-	memset(fsg, 0, sizeof *fsg);
 	spin_lock_init(&fsg->lock);
 	init_rwsem(&fsg->filesem);
 	init_waitqueue_head(&fsg->thread_wqh);
@@ -4080,15 +4083,9 @@ static int __init fsg_init(void)
 	if ((rc = fsg_alloc()) != 0)
 		return rc;
 	fsg = the_fsg;
-	if ((rc = usb_gadget_register_driver(&fsg_driver)) != 0) {
+	if ((rc = usb_gadget_register_driver(&fsg_driver)) != 0)
 		fsg_free(fsg);
-		return rc;
-	}
-	set_bit(REGISTERED, &fsg->atomic_bitflags);
-
-	/* Tell the thread to start working */
-	wake_up_process(fsg->thread_task);
-	return 0;
+	return rc;
 }
 module_init(fsg_init);
 
-- 
cgit v1.1


From bb200f6eac6372839921be1fe87c1f5c292a7bd6 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Mon, 3 Oct 2005 16:36:29 -0400
Subject: [PATCH] UHCI: unify BIOS handoff and driver reset code

This patch (as574) updates the PCI BIOS usb-handoff code for UHCI
controllers, making it work like the reset routines in uhci-hcd.  This
allows uhci-hcd to drop its own routines in favor of the new ones
(code-sharing).

Once the patch is merged we can turn the usb-handoff option on
permanently, as far as UHCI is concerned.  OHCI and EHCI may still have
some issues.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/pci-quirks.c | 142 ++++++++++++++++++++++++++++--------------
 drivers/usb/host/uhci-hcd.c   |  76 +++-------------------
 2 files changed, 106 insertions(+), 112 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c
index 49f7381..f7411ca 100644
--- a/drivers/usb/host/pci-quirks.c
+++ b/drivers/usb/host/pci-quirks.c
@@ -9,6 +9,12 @@
  */
 
 #include <linux/config.h>
+#ifdef CONFIG_USB_DEBUG
+#define DEBUG
+#else
+#undef DEBUG
+#endif
+
 #include <linux/types.h>
 #include <linux/kernel.h>
 #include <linux/pci.h>
@@ -46,13 +52,14 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82371AB_2,	qui
 
 #define UHCI_USBLEGSUP		0xc0		/* legacy support */
 #define UHCI_USBCMD		0		/* command register */
-#define UHCI_USBSTS		2		/* status register */
 #define UHCI_USBINTR		4		/* interrupt register */
-#define UHCI_USBLEGSUP_DEFAULT	0x2000		/* only PIRQ enable set */
-#define UHCI_USBCMD_RUN		(1 << 0)	/* RUN/STOP bit */
-#define UHCI_USBCMD_GRESET	(1 << 2)	/* Global reset */
-#define UHCI_USBCMD_CONFIGURE	(1 << 6)	/* config semaphore */
-#define UHCI_USBSTS_HALTED	(1 << 5)	/* HCHalted bit */
+#define UHCI_USBLEGSUP_RWC	0x8f00		/* the R/WC bits */
+#define UHCI_USBLEGSUP_RO	0x5040		/* R/O and reserved bits */
+#define UHCI_USBCMD_RUN		0x0001		/* RUN/STOP bit */
+#define UHCI_USBCMD_HCRESET	0x0002		/* Host Controller reset */
+#define UHCI_USBCMD_EGSM	0x0008		/* Global Suspend Mode */
+#define UHCI_USBCMD_CONFIGURE	0x0040		/* Config Flag */
+#define UHCI_USBINTR_RESUME	0x0002		/* Resume interrupt enable */
 
 #define OHCI_CONTROL		0x04
 #define OHCI_CMDSTATUS		0x08
@@ -84,57 +91,100 @@ static int __init usb_handoff_early(char *str)
 }
 __setup("usb-handoff", usb_handoff_early);
 
-static void __devinit quirk_usb_handoff_uhci(struct pci_dev *pdev)
+/*
+ * Make sure the controller is completely inactive, unable to
+ * generate interrupts or do DMA.
+ */
+void uhci_reset_hc(struct pci_dev *pdev, unsigned long base)
 {
-	unsigned long base = 0;
-	int wait_time, delta;
-	u16 val, sts;
-	int i;
+	/* Turn off PIRQ enable and SMI enable.  (This also turns off the
+	 * BIOS's USB Legacy Support.)  Turn off all the R/WC bits too.
+	 */
+	pci_write_config_word(pdev, UHCI_USBLEGSUP, UHCI_USBLEGSUP_RWC);
 
-	for (i = 0; i < PCI_ROM_RESOURCE; i++)
-		if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
-			base = pci_resource_start(pdev, i);
-			break;
-		}
+	/* Reset the HC - this will force us to get a
+	 * new notification of any already connected
+	 * ports due to the virtual disconnect that it
+	 * implies.
+	 */
+	outw(UHCI_USBCMD_HCRESET, base + UHCI_USBCMD);
+	mb();
+	udelay(5);
+	if (inw(base + UHCI_USBCMD) & UHCI_USBCMD_HCRESET)
+		dev_warn(&pdev->dev, "HCRESET not completed yet!\n");
+
+	/* Just to be safe, disable interrupt requests and
+	 * make sure the controller is stopped.
+	 */
+	outw(0, base + UHCI_USBINTR);
+	outw(0, base + UHCI_USBCMD);
+}
+EXPORT_SYMBOL_GPL(uhci_reset_hc);
 
-	if (!base)
-		return;
+/*
+ * Initialize a controller that was newly discovered or has just been
+ * resumed.  In either case we can't be sure of its previous state.
+ *
+ * Returns: 1 if the controller was reset, 0 otherwise.
+ */
+int uhci_check_and_reset_hc(struct pci_dev *pdev, unsigned long base)
+{
+	u16 legsup;
+	unsigned int cmd, intr;
 
 	/*
-	 * stop controller
+	 * When restarting a suspended controller, we expect all the
+	 * settings to be the same as we left them:
+	 *
+	 *	PIRQ and SMI disabled, no R/W bits set in USBLEGSUP;
+	 *	Controller is stopped and configured with EGSM set;
+	 *	No interrupts enabled except possibly Resume Detect.
+	 *
+	 * If any of these conditions are violated we do a complete reset.
 	 */
-	sts = inw(base + UHCI_USBSTS);
-	val = inw(base + UHCI_USBCMD);
-	val &= ~(u16)(UHCI_USBCMD_RUN | UHCI_USBCMD_CONFIGURE);
-	outw(val, base + UHCI_USBCMD);
+	pci_read_config_word(pdev, UHCI_USBLEGSUP, &legsup);
+	if (legsup & ~(UHCI_USBLEGSUP_RO | UHCI_USBLEGSUP_RWC)) {
+		dev_dbg(&pdev->dev, "%s: legsup = 0x%04x\n",
+				__FUNCTION__, legsup);
+		goto reset_needed;
+	}
 
-	/*
-	 * wait while it stops if it was running
-	 */
-	if ((sts & UHCI_USBSTS_HALTED) == 0)
-	{
-		wait_time = 1000;
-		delta = 100;
+	cmd = inw(base + UHCI_USBCMD);
+	if ((cmd & UHCI_USBCMD_RUN) || !(cmd & UHCI_USBCMD_CONFIGURE) ||
+			!(cmd & UHCI_USBCMD_EGSM)) {
+		dev_dbg(&pdev->dev, "%s: cmd = 0x%04x\n",
+				__FUNCTION__, cmd);
+		goto reset_needed;
+	}
 
-		do {
-			outw(0x1f, base + UHCI_USBSTS);
-			udelay(delta);
-			wait_time -= delta;
-			val = inw(base + UHCI_USBSTS);
-			if (val & UHCI_USBSTS_HALTED)
-				break;
-		} while (wait_time > 0);
+	intr = inw(base + UHCI_USBINTR);
+	if (intr & (~UHCI_USBINTR_RESUME)) {
+		dev_dbg(&pdev->dev, "%s: intr = 0x%04x\n",
+				__FUNCTION__, intr);
+		goto reset_needed;
 	}
+	return 0;
 
-	/*
-	 * disable interrupts & legacy support
-	 */
-	outw(0, base + UHCI_USBINTR);
-	outw(0x1f, base + UHCI_USBSTS);
-	pci_read_config_word(pdev, UHCI_USBLEGSUP, &val);
-	if (val & 0xbf)
-		pci_write_config_word(pdev, UHCI_USBLEGSUP, UHCI_USBLEGSUP_DEFAULT);
+reset_needed:
+	dev_dbg(&pdev->dev, "Performing full reset\n");
+	uhci_reset_hc(pdev, base);
+	return 1;
+}
+EXPORT_SYMBOL_GPL(uhci_check_and_reset_hc);
+
+static void __devinit quirk_usb_handoff_uhci(struct pci_dev *pdev)
+{
+	unsigned long base = 0;
+	int i;
+
+	for (i = 0; i < PCI_ROM_RESOURCE; i++)
+		if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
+			base = pci_resource_start(pdev, i);
+			break;
+		}
 
+	if (base)
+		uhci_check_and_reset_hc(pdev, base);
 }
 
 static void __devinit quirk_usb_handoff_ohci(struct pci_dev *pdev)
diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c
index 34c9dbc..6df555e 100644
--- a/drivers/usb/host/uhci-hcd.c
+++ b/drivers/usb/host/uhci-hcd.c
@@ -101,37 +101,16 @@ static void uhci_get_current_frame_number(struct uhci_hcd *uhci);
 #include "uhci-q.c"
 #include "uhci-hub.c"
 
+extern void uhci_reset_hc(struct pci_dev *pdev, unsigned long base);
+extern int uhci_check_and_reset_hc(struct pci_dev *pdev, unsigned long base);
+
 /*
- * Make sure the controller is completely inactive, unable to
- * generate interrupts or do DMA.
+ * Finish up a host controller reset and update the recorded state.
  */
-static void reset_hc(struct uhci_hcd *uhci)
+static void finish_reset(struct uhci_hcd *uhci)
 {
 	int port;
 
-	/* Turn off PIRQ enable and SMI enable.  (This also turns off the
-	 * BIOS's USB Legacy Support.)  Turn off all the R/WC bits too.
-	 */
-	pci_write_config_word(to_pci_dev(uhci_dev(uhci)), USBLEGSUP,
-			USBLEGSUP_RWC);
-
-	/* Reset the HC - this will force us to get a
-	 * new notification of any already connected
-	 * ports due to the virtual disconnect that it
-	 * implies.
-	 */
-	outw(USBCMD_HCRESET, uhci->io_addr + USBCMD);
-	mb();
-	udelay(5);
-	if (inw(uhci->io_addr + USBCMD) & USBCMD_HCRESET)
-		dev_warn(uhci_dev(uhci), "HCRESET not completed yet!\n");
-
-	/* Just to be safe, disable interrupt requests and
-	 * make sure the controller is stopped.
-	 */
-	outw(0, uhci->io_addr + USBINTR);
-	outw(0, uhci->io_addr + USBCMD);
-
 	/* HCRESET doesn't affect the Suspend, Reset, and Resume Detect
 	 * bits in the port status and control registers.
 	 * We have to clear them by hand.
@@ -153,7 +132,8 @@ static void reset_hc(struct uhci_hcd *uhci)
  */
 static void hc_died(struct uhci_hcd *uhci)
 {
-	reset_hc(uhci);
+	uhci_reset_hc(to_pci_dev(uhci_dev(uhci)), uhci->io_addr);
+	finish_reset(uhci);
 	uhci->hc_inaccessible = 1;
 }
 
@@ -163,44 +143,8 @@ static void hc_died(struct uhci_hcd *uhci)
  */
 static void check_and_reset_hc(struct uhci_hcd *uhci)
 {
-	u16 legsup;
-	unsigned int cmd, intr;
-
-	/*
-	 * When restarting a suspended controller, we expect all the
-	 * settings to be the same as we left them:
-	 *
-	 *	PIRQ and SMI disabled, no R/W bits set in USBLEGSUP;
-	 *	Controller is stopped and configured with EGSM set;
-	 *	No interrupts enabled except possibly Resume Detect.
-	 *
-	 * If any of these conditions are violated we do a complete reset.
-	 */
-	pci_read_config_word(to_pci_dev(uhci_dev(uhci)), USBLEGSUP, &legsup);
-	if (legsup & ~(USBLEGSUP_RO | USBLEGSUP_RWC)) {
-		dev_dbg(uhci_dev(uhci), "%s: legsup = 0x%04x\n",
-				__FUNCTION__, legsup);
-		goto reset_needed;
-	}
-
-	cmd = inw(uhci->io_addr + USBCMD);
-	if ((cmd & USBCMD_RS) || !(cmd & USBCMD_CF) || !(cmd & USBCMD_EGSM)) {
-		dev_dbg(uhci_dev(uhci), "%s: cmd = 0x%04x\n",
-				__FUNCTION__, cmd);
-		goto reset_needed;
-	}
-
-	intr = inw(uhci->io_addr + USBINTR);
-	if (intr & (~USBINTR_RESUME)) {
-		dev_dbg(uhci_dev(uhci), "%s: intr = 0x%04x\n",
-				__FUNCTION__, intr);
-		goto reset_needed;
-	}
-	return;
-
-reset_needed:
-	dev_dbg(uhci_dev(uhci), "Performing full reset\n");
-	reset_hc(uhci);
+	if (uhci_check_and_reset_hc(to_pci_dev(uhci_dev(uhci)), uhci->io_addr))
+		finish_reset(uhci);
 }
 
 /*
@@ -714,7 +658,7 @@ static void uhci_stop(struct usb_hcd *hcd)
 
 	spin_lock_irq(&uhci->lock);
 	if (!uhci->hc_inaccessible)
-		reset_hc(uhci);
+		hc_died(uhci);
 	uhci_scan_schedule(uhci, NULL);
 	spin_unlock_irq(&uhci->lock);
 
-- 
cgit v1.1


From 0c0382e32d46f606951010b202382be14d180a17 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Thu, 13 Oct 2005 17:08:02 -0400
Subject: [PATCH] USB: Rename hcd->hub_suspend to hcd->bus_suspend

This patch (as580) is perhaps the only result from the long discussion I
had with David about his changes to the root-hub suspend/resume code.  It
renames the hub_suspend and hub_resume methods in struct usb_hcd to
bus_suspend and bus_resume.  These are more descriptive names, since the
methods really do suspend or resume an entire USB bus, and less likely to
be confused with the hub_suspend and hub_resume routines in hub.c.

It also takes David's advice about removing the layer of bus glue, where
those methods are called.  And it implements a related change that David
made to the other HCDs but forgot to put into dummy_hcd.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/hcd.c          | 16 ++++++----------
 drivers/usb/core/hcd.h          | 23 +++++++++++++++++------
 drivers/usb/core/hub.c          |  8 ++++----
 drivers/usb/gadget/dummy_hcd.c  | 22 ++++------------------
 drivers/usb/host/ehci-hub.c     |  8 ++++----
 drivers/usb/host/ehci-pci.c     |  4 ++--
 drivers/usb/host/isp116x-hcd.c  | 12 ++++++------
 drivers/usb/host/ohci-au1xxx.c  |  4 ++--
 drivers/usb/host/ohci-hub.c     |  6 +++---
 drivers/usb/host/ohci-lh7a404.c |  4 ++--
 drivers/usb/host/ohci-omap.c    |  4 ++--
 drivers/usb/host/ohci-pci.c     |  4 ++--
 drivers/usb/host/ohci-ppc-soc.c |  4 ++--
 drivers/usb/host/ohci-pxa27x.c  |  4 ++--
 drivers/usb/host/ohci-s3c2410.c |  4 ++--
 drivers/usb/host/ohci-sa1111.c  |  4 ++--
 drivers/usb/host/sl811-hcd.c    | 16 ++++++++--------
 drivers/usb/host/uhci-hcd.c     |  4 ++--
 18 files changed, 72 insertions(+), 79 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index b7bb8dd..9ad3912 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -1433,16 +1433,16 @@ rescan:
 
 #ifdef	CONFIG_PM
 
-static int hcd_hub_suspend (struct usb_bus *bus)
+int hcd_bus_suspend (struct usb_bus *bus)
 {
 	struct usb_hcd		*hcd;
 	int			status;
 
 	hcd = container_of (bus, struct usb_hcd, self);
-	if (!hcd->driver->hub_suspend)
+	if (!hcd->driver->bus_suspend)
 		return -ENOENT;
 	hcd->state = HC_STATE_QUIESCING;
-	status = hcd->driver->hub_suspend (hcd);
+	status = hcd->driver->bus_suspend (hcd);
 	if (status == 0)
 		hcd->state = HC_STATE_SUSPENDED;
 	else
@@ -1451,18 +1451,18 @@ static int hcd_hub_suspend (struct usb_bus *bus)
 	return status;
 }
 
-static int hcd_hub_resume (struct usb_bus *bus)
+int hcd_bus_resume (struct usb_bus *bus)
 {
 	struct usb_hcd		*hcd;
 	int			status;
 
 	hcd = container_of (bus, struct usb_hcd, self);
-	if (!hcd->driver->hub_resume)
+	if (!hcd->driver->bus_resume)
 		return -ENOENT;
 	if (hcd->state == HC_STATE_RUNNING)
 		return 0;
 	hcd->state = HC_STATE_RESUMING;
-	status = hcd->driver->hub_resume (hcd);
+	status = hcd->driver->bus_resume (hcd);
 	if (status == 0)
 		hcd->state = HC_STATE_RUNNING;
 	else {
@@ -1590,10 +1590,6 @@ static struct usb_operations usb_hcd_operations = {
 	.buffer_alloc =		hcd_buffer_alloc,
 	.buffer_free =		hcd_buffer_free,
 	.disable =		hcd_endpoint_disable,
-#ifdef	CONFIG_PM
-	.hub_suspend =		hcd_hub_suspend,
-	.hub_resume =		hcd_hub_resume,
-#endif
 };
 
 /*-------------------------------------------------------------------------*/
diff --git a/drivers/usb/core/hcd.h b/drivers/usb/core/hcd.h
index 74757fc..d8f0d29 100644
--- a/drivers/usb/core/hcd.h
+++ b/drivers/usb/core/hcd.h
@@ -154,10 +154,6 @@ struct usb_operations {
 
 	void (*disable)(struct usb_device *udev,
 			struct usb_host_endpoint *ep);
-
-	/* global suspend/resume of bus */
-	int (*hub_suspend)(struct usb_bus *);
-	int (*hub_resume)(struct usb_bus *);
 };
 
 /* each driver provides one of these, and hardware init support */
@@ -212,8 +208,8 @@ struct hc_driver {
 	int		(*hub_control) (struct usb_hcd *hcd,
 				u16 typeReq, u16 wValue, u16 wIndex,
 				char *buf, u16 wLength);
-	int		(*hub_suspend)(struct usb_hcd *);
-	int		(*hub_resume)(struct usb_hcd *);
+	int		(*bus_suspend)(struct usb_hcd *);
+	int		(*bus_resume)(struct usb_hcd *);
 	int		(*start_port_reset)(struct usb_hcd *, unsigned port_num);
 	void		(*hub_irq_enable)(struct usb_hcd *);
 		/* Needed only if port-change IRQs are level-triggered */
@@ -379,6 +375,21 @@ extern int usb_find_interface_driver (struct usb_device *dev,
 
 #define usb_endpoint_out(ep_dir)	(!((ep_dir) & USB_DIR_IN))
 
+#ifdef CONFIG_PM
+extern int hcd_bus_suspend (struct usb_bus *bus);
+extern int hcd_bus_resume (struct usb_bus *bus);
+#else
+static inline int hcd_bus_suspend(struct usb_bus *bus)
+{
+	return 0;
+}
+
+static inline int hcd_bus_resume (struct usb_bus *bus)
+{
+	return 0;
+}
+#endif /* CONFIG_PM */
+
 /*
  * USB device fs stuff
  */
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index e2802bf..273e6cc 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1917,8 +1917,8 @@ static int hub_suspend(struct usb_interface *intf, pm_message_t msg)
 	/* "global suspend" of the downstream HC-to-USB interface */
 	if (!hdev->parent) {
 		struct usb_bus	*bus = hdev->bus;
-		if (bus && bus->op->hub_suspend) {
-			int	status = bus->op->hub_suspend (bus);
+		if (bus) {
+			int	status = hcd_bus_suspend (bus);
 
 			if (status != 0) {
 				dev_dbg(&hdev->dev, "'global' suspend %d\n",
@@ -1943,8 +1943,8 @@ static int hub_resume(struct usb_interface *intf)
 	/* "global resume" of the downstream HC-to-USB interface */
 	if (!hdev->parent) {
 		struct usb_bus	*bus = hdev->bus;
-		if (bus && bus->op->hub_resume) {
-			status = bus->op->hub_resume (bus);
+		if (bus) {
+			status = hcd_bus_resume (bus);
 			if (status) {
 				dev_dbg(&intf->dev, "'global' resume %d\n",
 					status);
diff --git a/drivers/usb/gadget/dummy_hcd.c b/drivers/usb/gadget/dummy_hcd.c
index 5032017..c605aae 100644
--- a/drivers/usb/gadget/dummy_hcd.c
+++ b/drivers/usb/gadget/dummy_hcd.c
@@ -1751,7 +1751,7 @@ static int dummy_hub_control (
 	return retval;
 }
 
-static int dummy_hub_suspend (struct usb_hcd *hcd)
+static int dummy_bus_suspend (struct usb_hcd *hcd)
 {
 	struct dummy *dum = hcd_to_dummy (hcd);
 
@@ -1762,7 +1762,7 @@ static int dummy_hub_suspend (struct usb_hcd *hcd)
 	return 0;
 }
 
-static int dummy_hub_resume (struct usb_hcd *hcd)
+static int dummy_bus_resume (struct usb_hcd *hcd)
 {
 	struct dummy *dum = hcd_to_dummy (hcd);
 
@@ -1894,8 +1894,8 @@ static const struct hc_driver dummy_hcd = {
 
 	.hub_status_data = 	dummy_hub_status,
 	.hub_control = 		dummy_hub_control,
-	.hub_suspend =		dummy_hub_suspend,
-	.hub_resume =		dummy_hub_resume,
+	.bus_suspend =		dummy_bus_suspend,
+	.bus_resume =		dummy_bus_resume,
 };
 
 static int dummy_hcd_probe (struct device *dev)
@@ -1936,13 +1936,6 @@ static int dummy_hcd_suspend (struct device *dev, pm_message_t state)
 	dev_dbg (dev, "%s\n", __FUNCTION__);
 	hcd = dev_get_drvdata (dev);
 
-#ifndef CONFIG_USB_SUSPEND
-	/* Otherwise this would never happen */
-	usb_lock_device (hcd->self.root_hub);
-	dummy_hub_suspend (hcd);
-	usb_unlock_device (hcd->self.root_hub);
-#endif
-
 	hcd->state = HC_STATE_SUSPENDED;
 	return 0;
 }
@@ -1955,13 +1948,6 @@ static int dummy_hcd_resume (struct device *dev)
 	hcd = dev_get_drvdata (dev);
 	hcd->state = HC_STATE_RUNNING;
 
-#ifndef CONFIG_USB_SUSPEND
-	/* Otherwise this would never happen */
-	usb_lock_device (hcd->self.root_hub);
-	dummy_hub_resume (hcd);
-	usb_unlock_device (hcd->self.root_hub);
-#endif
-
 	usb_hcd_poll_rh_status (hcd);
 	return 0;
 }
diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c
index 18d3f22..88cb4ad 100644
--- a/drivers/usb/host/ehci-hub.c
+++ b/drivers/usb/host/ehci-hub.c
@@ -30,7 +30,7 @@
 
 #ifdef	CONFIG_PM
 
-static int ehci_hub_suspend (struct usb_hcd *hcd)
+static int ehci_bus_suspend (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
 	int			port;
@@ -83,7 +83,7 @@ static int ehci_hub_suspend (struct usb_hcd *hcd)
 
 
 /* caller has locked the root hub, and should reset/reinit on error */
-static int ehci_hub_resume (struct usb_hcd *hcd)
+static int ehci_bus_resume (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
 	u32			temp;
@@ -159,8 +159,8 @@ static int ehci_hub_resume (struct usb_hcd *hcd)
 
 #else
 
-#define ehci_hub_suspend	NULL
-#define ehci_hub_resume		NULL
+#define ehci_bus_suspend	NULL
+#define ehci_bus_resume		NULL
 
 #endif	/* CONFIG_PM */
 
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index 66ebf75..8bbc8df 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -363,8 +363,8 @@ static const struct hc_driver ehci_pci_hc_driver = {
 	 */
 	.hub_status_data =	ehci_hub_status_data,
 	.hub_control =		ehci_hub_control,
-	.hub_suspend =		ehci_hub_suspend,
-	.hub_resume =		ehci_hub_resume,
+	.bus_suspend =		ehci_bus_suspend,
+	.bus_resume =		ehci_bus_resume,
 };
 
 /*-------------------------------------------------------------------------*/
diff --git a/drivers/usb/host/isp116x-hcd.c b/drivers/usb/host/isp116x-hcd.c
index f68220f..ddb8fc5 100644
--- a/drivers/usb/host/isp116x-hcd.c
+++ b/drivers/usb/host/isp116x-hcd.c
@@ -1160,7 +1160,7 @@ static int isp116x_hub_control(struct usb_hcd *hcd,
 
 #ifdef	CONFIG_PM
 
-static int isp116x_hub_suspend(struct usb_hcd *hcd)
+static int isp116x_bus_suspend(struct usb_hcd *hcd)
 {
 	struct isp116x *isp116x = hcd_to_isp116x(hcd);
 	unsigned long flags;
@@ -1200,7 +1200,7 @@ static int isp116x_hub_suspend(struct usb_hcd *hcd)
 	return ret;
 }
 
-static int isp116x_hub_resume(struct usb_hcd *hcd)
+static int isp116x_bus_resume(struct usb_hcd *hcd)
 {
 	struct isp116x *isp116x = hcd_to_isp116x(hcd);
 	u32 val;
@@ -1266,8 +1266,8 @@ static int isp116x_hub_resume(struct usb_hcd *hcd)
 
 #else
 
-#define	isp116x_hub_suspend	NULL
-#define	isp116x_hub_resume	NULL
+#define	isp116x_bus_suspend	NULL
+#define	isp116x_bus_resume	NULL
 
 #endif
 
@@ -1626,8 +1626,8 @@ static struct hc_driver isp116x_hc_driver = {
 
 	.hub_status_data = isp116x_hub_status_data,
 	.hub_control = isp116x_hub_control,
-	.hub_suspend = isp116x_hub_suspend,
-	.hub_resume = isp116x_hub_resume,
+	.bus_suspend = isp116x_bus_suspend,
+	.bus_resume = isp116x_bus_resume,
 };
 
 /*----------------------------------------------------------------*/
diff --git a/drivers/usb/host/ohci-au1xxx.c b/drivers/usb/host/ohci-au1xxx.c
index 550d67a..ac463c4 100644
--- a/drivers/usb/host/ohci-au1xxx.c
+++ b/drivers/usb/host/ohci-au1xxx.c
@@ -215,8 +215,8 @@ static const struct hc_driver ohci_au1xxx_hc_driver = {
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
 #ifdef	CONFIG_PM
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c
index 39a60e7..e01e77b 100644
--- a/drivers/usb/host/ohci-hub.c
+++ b/drivers/usb/host/ohci-hub.c
@@ -45,7 +45,7 @@ static void dl_done_list (struct ohci_hcd *, struct pt_regs *);
 static void finish_unlinks (struct ohci_hcd *, u16 , struct pt_regs *);
 static int ohci_restart (struct ohci_hcd *ohci);
 
-static int ohci_hub_suspend (struct usb_hcd *hcd)
+static int ohci_bus_suspend (struct usb_hcd *hcd)
 {
 	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
 	int			status = 0;
@@ -135,7 +135,7 @@ static inline struct ed *find_head (struct ed *ed)
 }
 
 /* caller has locked the root hub */
-static int ohci_hub_resume (struct usb_hcd *hcd)
+static int ohci_bus_resume (struct usb_hcd *hcd)
 {
 	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
 	u32			temp, enables;
@@ -362,7 +362,7 @@ done:
 			&& usb_trylock_device (hcd->self.root_hub)
 			) {
 		ohci_vdbg (ohci, "autosuspend\n");
-		(void) ohci_hub_suspend (hcd);
+		(void) ohci_bus_suspend (hcd);
 		usb_unlock_device (hcd->self.root_hub);
 	}
 #endif
diff --git a/drivers/usb/host/ohci-lh7a404.c b/drivers/usb/host/ohci-lh7a404.c
index 71d975a..e2ed55b 100644
--- a/drivers/usb/host/ohci-lh7a404.c
+++ b/drivers/usb/host/ohci-lh7a404.c
@@ -194,8 +194,8 @@ static const struct hc_driver ohci_lh7a404_hc_driver = {
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
 #ifdef	CONFIG_PM
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index b3498b9..982cdca 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -421,8 +421,8 @@ static const struct hc_driver ohci_omap_hc_driver = {
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
 #ifdef	CONFIG_PM
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c
index 99a0ad4..a8dde8b 100644
--- a/drivers/usb/host/ohci-pci.c
+++ b/drivers/usb/host/ohci-pci.c
@@ -195,8 +195,8 @@ static const struct hc_driver ohci_pci_hc_driver = {
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
 #ifdef	CONFIG_PM
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
diff --git a/drivers/usb/host/ohci-ppc-soc.c b/drivers/usb/host/ohci-ppc-soc.c
index ec20710..228845e 100644
--- a/drivers/usb/host/ohci-ppc-soc.c
+++ b/drivers/usb/host/ohci-ppc-soc.c
@@ -164,8 +164,8 @@ static const struct hc_driver ohci_ppc_soc_hc_driver = {
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
 #ifdef	CONFIG_PM
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index 2e7b485..d287dcc 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -279,8 +279,8 @@ static const struct hc_driver ohci_pxa27x_hc_driver = {
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
 #ifdef  CONFIG_PM
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
diff --git a/drivers/usb/host/ohci-s3c2410.c b/drivers/usb/host/ohci-s3c2410.c
index 922e2a6..3225d45 100644
--- a/drivers/usb/host/ohci-s3c2410.c
+++ b/drivers/usb/host/ohci-s3c2410.c
@@ -449,8 +449,8 @@ static const struct hc_driver ohci_s3c2410_hc_driver = {
 	.hub_status_data =	ohci_s3c2410_hub_status_data,
 	.hub_control =		ohci_s3c2410_hub_control,
 #ifdef	CONFIG_PM
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
diff --git a/drivers/usb/host/ohci-sa1111.c b/drivers/usb/host/ohci-sa1111.c
index 13324b7..fb3221e 100644
--- a/drivers/usb/host/ohci-sa1111.c
+++ b/drivers/usb/host/ohci-sa1111.c
@@ -236,8 +236,8 @@ static const struct hc_driver ohci_sa1111_hc_driver = {
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
 #ifdef	CONFIG_PM
-	.hub_suspend =		ohci_hub_suspend,
-	.hub_resume =		ohci_hub_resume,
+	.bus_suspend =		ohci_bus_suspend,
+	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };
diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c
index b5e7a47..1e47c1f 100644
--- a/drivers/usb/host/sl811-hcd.c
+++ b/drivers/usb/host/sl811-hcd.c
@@ -1363,7 +1363,7 @@ error:
 #ifdef	CONFIG_PM
 
 static int
-sl811h_hub_suspend(struct usb_hcd *hcd)
+sl811h_bus_suspend(struct usb_hcd *hcd)
 {
 	// SOFs off
 	DBG("%s\n", __FUNCTION__);
@@ -1371,7 +1371,7 @@ sl811h_hub_suspend(struct usb_hcd *hcd)
 }
 
 static int
-sl811h_hub_resume(struct usb_hcd *hcd)
+sl811h_bus_resume(struct usb_hcd *hcd)
 {
 	// SOFs on
 	DBG("%s\n", __FUNCTION__);
@@ -1380,8 +1380,8 @@ sl811h_hub_resume(struct usb_hcd *hcd)
 
 #else
 
-#define	sl811h_hub_suspend	NULL
-#define	sl811h_hub_resume	NULL
+#define	sl811h_bus_suspend	NULL
+#define	sl811h_bus_resume	NULL
 
 #endif
 
@@ -1623,8 +1623,8 @@ static struct hc_driver sl811h_hc_driver = {
 	 */
 	.hub_status_data =	sl811h_hub_status_data,
 	.hub_control =		sl811h_hub_control,
-	.hub_suspend =		sl811h_hub_suspend,
-	.hub_resume =		sl811h_hub_resume,
+	.bus_suspend =		sl811h_bus_suspend,
+	.bus_resume =		sl811h_bus_resume,
 };
 
 /*-------------------------------------------------------------------------*/
@@ -1791,7 +1791,7 @@ sl811h_suspend(struct device *dev, pm_message_t state)
 	int		retval = 0;
 
 	if (state.event == PM_EVENT_FREEZE)
-		retval = sl811h_hub_suspend(hcd);
+		retval = sl811h_bus_suspend(hcd);
 	else if (state.event == PM_EVENT_SUSPEND)
 		port_power(sl811, 0);
 	if (retval == 0)
@@ -1816,7 +1816,7 @@ sl811h_resume(struct device *dev)
 	}
 
 	dev->power.power_state = PMSG_ON;
-	return sl811h_hub_resume(hcd);
+	return sl811h_bus_resume(hcd);
 }
 
 #else
diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c
index 6df555e..72cd157 100644
--- a/drivers/usb/host/uhci-hcd.c
+++ b/drivers/usb/host/uhci-hcd.c
@@ -804,8 +804,8 @@ static const struct hc_driver uhci_driver = {
 #ifdef CONFIG_PM
 	.suspend =		uhci_suspend,
 	.resume =		uhci_resume,
-	.hub_suspend =		uhci_rh_suspend,
-	.hub_resume =		uhci_rh_resume,
+	.bus_suspend =		uhci_rh_suspend,
+	.bus_resume =		uhci_rh_resume,
 #endif
 	.stop =			uhci_stop,
 
-- 
cgit v1.1


From b81d34363c0b17c47f4ef63d5888c4f47f315d29 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Thu, 13 Oct 2005 17:00:24 -0400
Subject: [PATCH] UHCI: Improve handling of iso TDs

The uhci-hcd driver is fairly lax about the way it handles isochronous
transfers.  This patch (as579) improves it in three respects:

	TDs for a new URB aren't added to the schedule until all of
	them have been allocated.  This way there's no risk of the
	controller executing some of them when an allocation fails.

	TDs for an unlinked URB are removed from the schedule as soon
	as the URB is unlinked, rather than waiting until the URB is
	given back.  This way there's no risk of the controller still
	executing a TD after the URB completes.

	The urb->error_count values are now reported correctly.
	Although since they aren't used in any drivers except for
	debug messages in the system log, probably nobody cares.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/uhci-q.c | 39 ++++++++++++++++++++++++++-------------
 1 file changed, 26 insertions(+), 13 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/uhci-q.c b/drivers/usb/host/uhci-q.c
index 51de06b..7e46887 100644
--- a/drivers/usb/host/uhci-q.c
+++ b/drivers/usb/host/uhci-q.c
@@ -108,13 +108,16 @@ static void uhci_insert_td_frame_list(struct uhci_hcd *uhci, struct uhci_td *td,
 	}
 }
 
-static void uhci_remove_td(struct uhci_hcd *uhci, struct uhci_td *td)
+static inline void uhci_remove_td_frame_list(struct uhci_hcd *uhci,
+		struct uhci_td *td)
 {
 	/* If it's not inserted, don't remove it */
-	if (td->frame == -1 && list_empty(&td->fl_list))
+	if (td->frame == -1) {
+		WARN_ON(!list_empty(&td->fl_list));
 		return;
+	}
 
-	if (td->frame != -1 && uhci->frame_cpu[td->frame] == td) {
+	if (uhci->frame_cpu[td->frame] == td) {
 		if (list_empty(&td->fl_list)) {
 			uhci->frame[td->frame] = td->link;
 			uhci->frame_cpu[td->frame] = NULL;
@@ -132,13 +135,20 @@ static void uhci_remove_td(struct uhci_hcd *uhci, struct uhci_td *td)
 		ptd->link = td->link;
 	}
 
-	wmb();
-	td->link = UHCI_PTR_TERM;
-
 	list_del_init(&td->fl_list);
 	td->frame = -1;
 }
 
+static void unlink_isochronous_tds(struct uhci_hcd *uhci, struct urb *urb)
+{
+	struct urb_priv *urbp = (struct urb_priv *) urb->hcpriv;
+	struct uhci_td *td;
+
+	list_for_each_entry(td, &urbp->td_list, list)
+		uhci_remove_td_frame_list(uhci, td);
+	wmb();
+}
+
 /*
  * Inserts a td list into qh.
  */
@@ -498,7 +508,6 @@ static void uhci_destroy_urb_priv(struct uhci_hcd *uhci, struct urb *urb)
 
 	list_for_each_entry_safe(td, tmp, &urbp->td_list, list) {
 		uhci_remove_td_from_urb(td);
-		uhci_remove_td(uhci, td);
 		list_add(&td->remove_list, &uhci->td_remove_list);
 	}
 
@@ -1068,6 +1077,7 @@ static int uhci_submit_isochronous(struct uhci_hcd *uhci, struct urb *urb)
 	struct uhci_td *td;
 	int i, ret, frame;
 	int status, destination;
+	struct urb_priv *urbp = (struct urb_priv *) urb->hcpriv;
 
 	status = TD_CTRL_ACTIVE | TD_CTRL_IOS;
 	destination = (urb->pipe & PIPE_DEVEP_MASK) | usb_packetid(urb->pipe);
@@ -1076,11 +1086,7 @@ static int uhci_submit_isochronous(struct uhci_hcd *uhci, struct urb *urb)
 	if (ret)
 		return ret;
 
-	frame = urb->start_frame;
-	for (i = 0; i < urb->number_of_packets; i++, frame += urb->interval) {
-		if (!urb->iso_frame_desc[i].length)
-			continue;
-
+	for (i = 0; i < urb->number_of_packets; i++) {
 		td = uhci_alloc_td(uhci);
 		if (!td)
 			return -ENOMEM;
@@ -1091,8 +1097,12 @@ static int uhci_submit_isochronous(struct uhci_hcd *uhci, struct urb *urb)
 
 		if (i + 1 >= urb->number_of_packets)
 			td->status |= cpu_to_le32(TD_CTRL_IOC);
+	}
 
+	frame = urb->start_frame;
+	list_for_each_entry(td, &urbp->td_list, list) {
 		uhci_insert_td_frame_list(uhci, td, frame);
+		frame += urb->interval;
 	}
 
 	return -EINPROGRESS;
@@ -1105,7 +1115,7 @@ static int uhci_result_isochronous(struct uhci_hcd *uhci, struct urb *urb)
 	int status;
 	int i, ret = 0;
 
-	urb->actual_length = 0;
+	urb->actual_length = urb->error_count = 0;
 
 	i = 0;
 	list_for_each_entry(td, &urbp->td_list, list) {
@@ -1129,6 +1139,7 @@ static int uhci_result_isochronous(struct uhci_hcd *uhci, struct urb *urb)
 
 		i++;
 	}
+	unlink_isochronous_tds(uhci, urb);
 
 	return ret;
 }
@@ -1361,6 +1372,8 @@ static int uhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb)
 		goto done;
 	list_del_init(&urbp->urb_list);
 
+	if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS)
+		unlink_isochronous_tds(uhci, urb);
 	uhci_unlink_generic(uhci, urb);
 
 	uhci_get_current_frame_number(uhci);
-- 
cgit v1.1


From af64a5ebb817532965d18b792d6d74afecfb0bcf Mon Sep 17 00:00:00 2001
From: Henk <Henk.Vergonet@gmail.com>
Date: Wed, 12 Oct 2005 15:02:56 +0200
Subject: [PATCH] USB: Buffer overflow patch for Yealink driver

Just a small patch that fixes a small parameter validation bug.

  drivers/usb/input/map_to_7segment.h:
    This patch fixes the broken parameter validation in the char to seg7
    conversion. This could cause out-of-bounds memory references.

  MAINTAINERS:
    Yealink maintainer info now in sorted order.

  Documentation/input/yealink.txt:
    Added a Q&A section that answers some common questions.

Signed-off-by: Henk <Henk.Vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

006491df1a13f85ad245d1039dfdf20e49c394fd
---
 drivers/usb/input/map_to_7segment.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers')

diff --git a/drivers/usb/input/map_to_7segment.h b/drivers/usb/input/map_to_7segment.h
index 52ff27f..a424094 100644
--- a/drivers/usb/input/map_to_7segment.h
+++ b/drivers/usb/input/map_to_7segment.h
@@ -79,7 +79,7 @@ struct seg7_conversion_map {
 
 static inline int map_to_seg7(struct seg7_conversion_map *map, int c)
 {
-	return c & 0x7f ? map->table[c] : -EINVAL;
+	return c >= 0 && c < sizeof(map->table) ? map->table[c] : -EINVAL;
 }
 
 #define SEG7_CONVERSION_MAP(_name, _map)	\
-- 
cgit v1.1


From cb97c5c9d0789d65d7ec42a80946fa9eb2ec5182 Mon Sep 17 00:00:00 2001
From: David Brownell <david-b@pacbell.net>
Date: Sun, 16 Oct 2005 15:06:51 -0700
Subject: [PATCH] omap_udc dma off-by-one fix

The change to make DMA work two bytes at a time omitted an important
tweak that affects the file_storage gadget:  it needs to recognize when
the host writes an odd number of bytes.  (The network layer ignores
such extra bytes.)

This patch resolves that issue by checking the relevant bit and adjusting
the rx byte count, so that for example a legal 13 byte request doesn't
morph into an illegal 14 byte one any more.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/gadget/omap_udc.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c
index b7885dc..de8a89a 100644
--- a/drivers/usb/gadget/omap_udc.c
+++ b/drivers/usb/gadget/omap_udc.c
@@ -691,7 +691,7 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req)
 }
 
 static void
-finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status)
+finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status, int one)
 {
 	u16	count;
 
@@ -699,6 +699,8 @@ finish_out_dma(struct omap_ep *ep, struct omap_req *req, int status)
 		ep->dma_counter = (u16) (req->req.dma + req->req.actual);
 	count = dma_dest_len(ep, req->req.dma + req->req.actual);
 	count += req->req.actual;
+	if (one)
+		count--;
 	if (count <= req->req.length)
 		req->req.actual = count;
 
@@ -747,7 +749,7 @@ static void dma_irq(struct omap_udc *udc, u16 irq_src)
 		if (!list_empty(&ep->queue)) {
 			req = container_of(ep->queue.next,
 					struct omap_req, queue);
-			finish_out_dma(ep, req, 0);
+			finish_out_dma(ep, req, 0, dman_stat & UDC_DMA_RX_SB);
 		}
 		UDC_IRQ_SRC_REG = UDC_RXN_EOT;
 
@@ -925,7 +927,7 @@ static void dma_channel_release(struct omap_ep *ep)
 		while (UDC_RXDMA_CFG_REG & mask)
 			udelay(10);
 		if (req)
-			finish_out_dma(ep, req, -ECONNRESET);
+			finish_out_dma(ep, req, -ECONNRESET, 0);
 	}
 	omap_free_dma(ep->lch);
 	ep->dma_channel = 0;
-- 
cgit v1.1


From f37be9b9be3ebc02d2d075d7f53f7802f3e005db Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Mon, 17 Oct 2005 10:42:06 -0400
Subject: [PATCH] Fix hcd->state assignments in uhci-hcd

This patch (as581) changes the assignments to hcd->state in the uhci-hcd
driver.  It fixes part of bugzilla entry #5227.  The problem was revealed
by David's large suite of USB suspend/resume patches; this patch should go
to Linus at the same time those do.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/uhci-hcd.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c
index 72cd157..d33ce39 100644
--- a/drivers/usb/host/uhci-hcd.c
+++ b/drivers/usb/host/uhci-hcd.c
@@ -161,8 +161,8 @@ static void configure_hc(struct uhci_hcd *uhci)
 	/* Set the current frame number */
 	outw(uhci->frame_number, uhci->io_addr + USBFRNUM);
 
-	/* Mark controller as running before we enable interrupts */
-	uhci_to_hcd(uhci)->state = HC_STATE_RUNNING;
+	/* Mark controller as not halted before we enable interrupts */
+	uhci_to_hcd(uhci)->state = HC_STATE_SUSPENDED;
 	mb();
 
 	/* Enable PIRQ */
@@ -263,6 +263,7 @@ __acquires(uhci->lock)
 
 static void start_rh(struct uhci_hcd *uhci)
 {
+	uhci_to_hcd(uhci)->state = HC_STATE_RUNNING;
 	uhci->is_stopped = 0;
 	smp_wmb();
 
@@ -708,7 +709,6 @@ static int uhci_suspend(struct usb_hcd *hcd, pm_message_t message)
 
 	if (uhci->rh_state > UHCI_RH_SUSPENDED) {
 		dev_warn(uhci_dev(uhci), "Root hub isn't suspended!\n");
-		hcd->state = HC_STATE_RUNNING;
 		rc = -EBUSY;
 		goto done;
 	};
-- 
cgit v1.1


From 4e67185a7ac3ecb1710e636e2f7e318e99298c7a Mon Sep 17 00:00:00 2001
From: Juha Yrj?l? <juha.yrjola@nokia.com>
Date: Sun, 16 Oct 2005 15:47:04 -0700
Subject: [PATCH] add usb transceiver set_suspend() method

When a USB device is put into suspend mode, the current drawn from VBUS
has to be less than 500 uA. Some transceivers need to be put into a
special power-saving mode to accomplish this, and won't have a separate
OTG driver handling that.

This adds a suspend method to the "otg_transceiver" struct -- misnamed,
it's not only for OTG -- and calls it from the OMAP UDC driver.

Signed-off-by: Juha Yrj?l? <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/gadget/omap_udc.c | 4 ++++
 1 file changed, 4 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c
index de8a89a..b42799b 100644
--- a/drivers/usb/gadget/omap_udc.c
+++ b/drivers/usb/gadget/omap_udc.c
@@ -1788,8 +1788,12 @@ static void devstate_irq(struct omap_udc *udc, u16 irq_src)
 					udc->driver->suspend(&udc->gadget);
 					spin_lock(&udc->lock);
 				}
+				if (udc->transceiver)
+					otg_set_suspend(udc->transceiver, 1);
 			} else {
 				VDBG("resume\n");
+				if (udc->transceiver)
+					otg_set_suspend(udc->transceiver, 0);
 				if (udc->gadget.speed == USB_SPEED_FULL
 						&& udc->driver->resume) {
 					spin_unlock(&udc->lock);
-- 
cgit v1.1


From a85ee6b50c8a1fca4034c8d6b21c91a8de171e01 Mon Sep 17 00:00:00 2001
From: Ben Dooks <ben-linux@fluff.org>
Date: Mon, 10 Oct 2005 01:23:50 +0100
Subject: [PATCH] USB: S3C2410 OHCI - add driver owner field

Initialise the .owner field of the driver with
the module that owns it, to aid in linking
drivers to modules.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/ohci-s3c2410.c | 1 +
 1 file changed, 1 insertion(+)

(limited to 'drivers')

diff --git a/drivers/usb/host/ohci-s3c2410.c b/drivers/usb/host/ohci-s3c2410.c
index 3225d45..fab420a 100644
--- a/drivers/usb/host/ohci-s3c2410.c
+++ b/drivers/usb/host/ohci-s3c2410.c
@@ -474,6 +474,7 @@ static int ohci_hcd_s3c2410_drv_remove(struct device *dev)
 
 static struct device_driver ohci_hcd_s3c2410_driver = {
 	.name		= "s3c2410-ohci",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_s3c2410_drv_probe,
 	.remove		= ohci_hcd_s3c2410_drv_remove,
-- 
cgit v1.1


From d0d5049fb02fc1082c17e08deecd6fed8db549b6 Mon Sep 17 00:00:00 2001
From: Ben Dooks <ben@fluff.org.uk>
Date: Mon, 10 Oct 2005 10:52:33 +0100
Subject: [PATCH] USB: gadget drivers - add .owner initialisation

Ensure the the device_driver and usb_gadget_driver
have their .owner fields initialised to associate
the module owner to the driver.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/gadget/dummy_hcd.c    | 2 ++
 drivers/usb/gadget/ether.c        | 1 +
 drivers/usb/gadget/file_storage.c | 1 +
 drivers/usb/gadget/goku_udc.c     | 1 +
 drivers/usb/gadget/lh7a40x_udc.c  | 1 +
 drivers/usb/gadget/net2280.c      | 1 +
 drivers/usb/gadget/omap_udc.c     | 1 +
 drivers/usb/gadget/pxa2xx_udc.c   | 1 +
 drivers/usb/gadget/zero.c         | 1 +
 9 files changed, 10 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/gadget/dummy_hcd.c b/drivers/usb/gadget/dummy_hcd.c
index c605aae..02106be 100644
--- a/drivers/usb/gadget/dummy_hcd.c
+++ b/drivers/usb/gadget/dummy_hcd.c
@@ -967,6 +967,7 @@ static int dummy_udc_resume (struct device *dev)
 
 static struct device_driver dummy_udc_driver = {
 	.name		= (char *) gadget_name,
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= dummy_udc_probe,
 	.remove		= dummy_udc_remove,
@@ -1954,6 +1955,7 @@ static int dummy_hcd_resume (struct device *dev)
 
 static struct device_driver dummy_hcd_driver = {
 	.name		= (char *) driver_name,
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= dummy_hcd_probe,
 	.remove		= dummy_hcd_remove,
diff --git a/drivers/usb/gadget/ether.c b/drivers/usb/gadget/ether.c
index f1024e8..8f402f8 100644
--- a/drivers/usb/gadget/ether.c
+++ b/drivers/usb/gadget/ether.c
@@ -2533,6 +2533,7 @@ static struct usb_gadget_driver eth_driver = {
 
 	.driver 	= {
 		.name		= (char *) shortname,
+		.owner		= THIS_MODULE,
 		// .shutdown = ...
 		// .suspend = ...
 		// .resume = ...
diff --git a/drivers/usb/gadget/file_storage.c b/drivers/usb/gadget/file_storage.c
index 86a6aeb..ea09aaa 100644
--- a/drivers/usb/gadget/file_storage.c
+++ b/drivers/usb/gadget/file_storage.c
@@ -4044,6 +4044,7 @@ static struct usb_gadget_driver		fsg_driver = {
 
 	.driver		= {
 		.name		= (char *) shortname,
+		.owner		= THIS_MODULE,
 		// .release = ...
 		// .suspend = ...
 		// .resume = ...
diff --git a/drivers/usb/gadget/goku_udc.c b/drivers/usb/gadget/goku_udc.c
index b0f3cd6..6544697 100644
--- a/drivers/usb/gadget/goku_udc.c
+++ b/drivers/usb/gadget/goku_udc.c
@@ -1970,6 +1970,7 @@ MODULE_DEVICE_TABLE (pci, pci_ids);
 static struct pci_driver goku_pci_driver = {
 	.name =		(char *) driver_name,
 	.id_table =	pci_ids,
+	.owner =	THIS_MODULE,
 
 	.probe =	goku_probe,
 	.remove =	goku_remove,
diff --git a/drivers/usb/gadget/lh7a40x_udc.c b/drivers/usb/gadget/lh7a40x_udc.c
index 012d1e5..9b36739 100644
--- a/drivers/usb/gadget/lh7a40x_udc.c
+++ b/drivers/usb/gadget/lh7a40x_udc.c
@@ -2140,6 +2140,7 @@ static int lh7a40x_udc_remove(struct device *_dev)
 
 static struct device_driver udc_driver = {
 	.name = (char *)driver_name,
+	.owner = THIS_MODULE,
 	.bus = &platform_bus_type,
 	.probe = lh7a40x_udc_probe,
 	.remove = lh7a40x_udc_remove
diff --git a/drivers/usb/gadget/net2280.c b/drivers/usb/gadget/net2280.c
index c32e1f7..0dc6bb0 100644
--- a/drivers/usb/gadget/net2280.c
+++ b/drivers/usb/gadget/net2280.c
@@ -2948,6 +2948,7 @@ MODULE_DEVICE_TABLE (pci, pci_ids);
 static struct pci_driver net2280_pci_driver = {
 	.name =		(char *) driver_name,
 	.id_table =	pci_ids,
+	.owner =	THIS_MODULE,
 
 	.probe =	net2280_probe,
 	.remove =	net2280_remove,
diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c
index b42799b..41c96b0 100644
--- a/drivers/usb/gadget/omap_udc.c
+++ b/drivers/usb/gadget/omap_udc.c
@@ -2949,6 +2949,7 @@ static int omap_udc_resume(struct device *dev)
 
 static struct device_driver udc_driver = {
 	.name		= (char *) driver_name,
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= omap_udc_probe,
 	.remove		= __exit_p(omap_udc_remove),
diff --git a/drivers/usb/gadget/pxa2xx_udc.c b/drivers/usb/gadget/pxa2xx_udc.c
index 6470285..f83a926 100644
--- a/drivers/usb/gadget/pxa2xx_udc.c
+++ b/drivers/usb/gadget/pxa2xx_udc.c
@@ -2631,6 +2631,7 @@ static int pxa2xx_udc_resume(struct device *dev)
 
 static struct device_driver udc_driver = {
 	.name		= "pxa2xx-udc",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= pxa2xx_udc_probe,
 	.shutdown	= pxa2xx_udc_shutdown,
diff --git a/drivers/usb/gadget/zero.c b/drivers/usb/gadget/zero.c
index ec9c424..6c58636 100644
--- a/drivers/usb/gadget/zero.c
+++ b/drivers/usb/gadget/zero.c
@@ -1302,6 +1302,7 @@ static struct usb_gadget_driver zero_driver = {
 
 	.driver 	= {
 		.name		= (char *) shortname,
+		.owner		= THIS_MODULE,
 		// .shutdown = ...
 		// .suspend = ...
 		// .resume = ...
-- 
cgit v1.1


From efa400db5332ba341cc354c9d8a5298ff57faa98 Mon Sep 17 00:00:00 2001
From: Ben Dooks <ben@fluff.org.uk>
Date: Mon, 10 Oct 2005 02:32:15 +0100
Subject: [PATCH] USB: add owner initialisation to host drivers

Add .owner initialisation to the device drivers
in drivers/usb/host so that when built as module
the device_driver refers to the owning module

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/ehci-pci.c     | 1 +
 drivers/usb/host/ohci-au1xxx.c  | 1 +
 drivers/usb/host/ohci-lh7a404.c | 1 +
 drivers/usb/host/ohci-omap.c    | 1 +
 drivers/usb/host/ohci-pci.c     | 1 +
 drivers/usb/host/ohci-ppc-soc.c | 1 +
 drivers/usb/host/sl811-hcd.c    | 1 +
 drivers/usb/host/uhci-hcd.c     | 1 +
 8 files changed, 8 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index 8bbc8df..7872469 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -383,6 +383,7 @@ MODULE_DEVICE_TABLE (pci, pci_ids);
 static struct pci_driver ehci_pci_driver = {
 	.name =		(char *) hcd_name,
 	.id_table =	pci_ids,
+	.owner = 	THIS_MODULE,
 
 	.probe =	usb_hcd_pci_probe,
 	.remove =	usb_hcd_pci_remove,
diff --git a/drivers/usb/host/ohci-au1xxx.c b/drivers/usb/host/ohci-au1xxx.c
index ac463c4..a277e25 100644
--- a/drivers/usb/host/ohci-au1xxx.c
+++ b/drivers/usb/host/ohci-au1xxx.c
@@ -264,6 +264,7 @@ static int ohci_hcd_au1xxx_drv_resume(struct device *dev)
 
 static struct device_driver ohci_hcd_au1xxx_driver = {
 	.name		= "au1xxx-ohci",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_au1xxx_drv_probe,
 	.remove		= ohci_hcd_au1xxx_drv_remove,
diff --git a/drivers/usb/host/ohci-lh7a404.c b/drivers/usb/host/ohci-lh7a404.c
index e2ed55b..238fa4a 100644
--- a/drivers/usb/host/ohci-lh7a404.c
+++ b/drivers/usb/host/ohci-lh7a404.c
@@ -244,6 +244,7 @@ static int ohci_hcd_lh7a404_drv_resume(struct device *dev)
 
 static struct device_driver ohci_hcd_lh7a404_driver = {
 	.name		= "lh7a404-ohci",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_lh7a404_drv_probe,
 	.remove		= ohci_hcd_lh7a404_drv_remove,
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index 982cdca..45efeed 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -492,6 +492,7 @@ static int ohci_omap_resume(struct device *dev)
  */
 static struct device_driver ohci_hcd_omap_driver = {
 	.name		= "ohci",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_omap_drv_probe,
 	.remove		= ohci_hcd_omap_drv_remove,
diff --git a/drivers/usb/host/ohci-pci.c b/drivers/usb/host/ohci-pci.c
index a8dde8b..bf1d5ab 100644
--- a/drivers/usb/host/ohci-pci.c
+++ b/drivers/usb/host/ohci-pci.c
@@ -216,6 +216,7 @@ MODULE_DEVICE_TABLE (pci, pci_ids);
 static struct pci_driver ohci_pci_driver = {
 	.name =		(char *) hcd_name,
 	.id_table =	pci_ids,
+	.owner =	THIS_MODULE,
 
 	.probe =	usb_hcd_pci_probe,
 	.remove =	usb_hcd_pci_remove,
diff --git a/drivers/usb/host/ohci-ppc-soc.c b/drivers/usb/host/ohci-ppc-soc.c
index 228845e..4832e57 100644
--- a/drivers/usb/host/ohci-ppc-soc.c
+++ b/drivers/usb/host/ohci-ppc-soc.c
@@ -193,6 +193,7 @@ static int ohci_hcd_ppc_soc_drv_remove(struct device *dev)
 
 static struct device_driver ohci_hcd_ppc_soc_driver = {
 	.name		= "ppc-soc-ohci",
+	.owner		= THIS_MODULE,
 	.bus		= &platform_bus_type,
 	.probe		= ohci_hcd_ppc_soc_drv_probe,
 	.remove		= ohci_hcd_ppc_soc_drv_remove,
diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c
index 1e47c1f..40169d9 100644
--- a/drivers/usb/host/sl811-hcd.c
+++ b/drivers/usb/host/sl811-hcd.c
@@ -1831,6 +1831,7 @@ sl811h_resume(struct device *dev)
 struct device_driver sl811h_driver = {
 	.name =		(char *) hcd_name,
 	.bus =		&platform_bus_type,
+	.owner =	THIS_MODULE,
 
 	.probe =	sl811h_probe,
 	.remove =	__devexit_p(sl811h_remove),
diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c
index d33ce39..15e0a51 100644
--- a/drivers/usb/host/uhci-hcd.c
+++ b/drivers/usb/host/uhci-hcd.c
@@ -831,6 +831,7 @@ MODULE_DEVICE_TABLE(pci, uhci_pci_ids);
 static struct pci_driver uhci_pci_driver = {
 	.name =		(char *)hcd_name,
 	.id_table =	uhci_pci_ids,
+	.owner =	THIS_MODULE,
 
 	.probe =	usb_hcd_pci_probe,
 	.remove =	usb_hcd_pci_remove,
-- 
cgit v1.1


From 3e8a556a02d5aa16375d4d74aad0f67cd844c047 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Tue, 18 Oct 2005 10:08:31 -0400
Subject: [PATCH] Missing transfer_flags setting in usbtest

This patch (as582) adds a missing transfer_flags setting to the usbtest
driver.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/misc/usbtest.c | 1 +
 1 file changed, 1 insertion(+)

(limited to 'drivers')

diff --git a/drivers/usb/misc/usbtest.c b/drivers/usb/misc/usbtest.c
index d055196..90a9625 100644
--- a/drivers/usb/misc/usbtest.c
+++ b/drivers/usb/misc/usbtest.c
@@ -983,6 +983,7 @@ test_ctrl_queue (struct usbtest_dev *dev, struct usbtest_param *param)
 		reqp->number = i % NUM_SUBCASES;
 		reqp->expected = expected;
 		u->setup_packet = (char *) &reqp->setup;
+		u->transfer_flags |= URB_NO_SETUP_DMA_MAP;
 
 		u->context = &context;
 		u->complete = ctrl_complete;
-- 
cgit v1.1


From 4592bf5a22593704bb9e8c584a81bf6ca4f6cfec Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: remove the global function usbdev_lookup_minor

It's only used locally.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/devio.c | 34 +++++++++++++++++-----------------
 drivers/usb/core/usb.h   |  1 -
 2 files changed, 17 insertions(+), 18 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index 6c15dab..9222b7a 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -517,6 +517,23 @@ static int check_ctrlrecip(struct dev_state *ps, unsigned int requesttype, unsig
 	return ret;
 }
 
+static struct usb_device *usbdev_lookup_minor(int minor)
+{
+	struct class_device *class_dev;
+	struct usb_device *dev = NULL;
+
+	down(&usb_device_class->sem);
+	list_for_each_entry(class_dev, &usb_device_class->children, node) {
+		if (class_dev->devt == MKDEV(USB_DEVICE_MAJOR, minor)) {
+			dev = class_dev->class_data;
+			break;
+		}
+	}
+	up(&usb_device_class->sem);
+
+	return dev;
+};
+
 /*
  * file operations
  */
@@ -1533,23 +1550,6 @@ struct file_operations usbfs_device_file_operations = {
 	.release =	usbdev_release,
 };
 
-struct usb_device *usbdev_lookup_minor(int minor)
-{
-	struct class_device *class_dev;
-	struct usb_device *dev = NULL;
-
-	down(&usb_device_class->sem);
-	list_for_each_entry(class_dev, &usb_device_class->children, node) {
-		if (class_dev->devt == MKDEV(USB_DEVICE_MAJOR, minor)) {
-			dev = class_dev->class_data;
-			break;
-		}
-	}
-	up(&usb_device_class->sem);
-
-	return dev;
-};
-
 void usbdev_add(struct usb_device *dev)
 {
 	int minor = ((dev->bus->busnum-1) * 128) + (dev->devnum-1);
diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
index 4d59f6e..3dc8096 100644
--- a/drivers/usb/core/usb.h
+++ b/drivers/usb/core/usb.h
@@ -64,7 +64,6 @@ extern int usbdev_init(void);
 extern void usbdev_cleanup(void);
 extern void usbdev_add(struct usb_device *dev);
 extern void usbdev_remove(struct usb_device *dev);
-extern struct usb_device *usbdev_lookup_minor(int minor);
 
 struct dev_state {
 	struct list_head list;      /* state list */
-- 
cgit v1.1


From 3099e75a7ccc3c5b0a4cf988a76d9c4a7fa5e91a Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: add notifier functions to the USB core for devices and
 busses

This should let us get rid of all of the different hooks in the USB core for
when something has changed.

Also, some other parts of the kernel have wanted to know this kind of
information at times.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/Makefile |   2 +-
 drivers/usb/core/hcd.c    |   2 +
 drivers/usb/core/hub.c    |   3 ++
 drivers/usb/core/notify.c | 120 ++++++++++++++++++++++++++++++++++++++++++++++
 drivers/usb/core/usb.h    |   6 +++
 5 files changed, 132 insertions(+), 1 deletion(-)
 create mode 100644 drivers/usb/core/notify.c

(limited to 'drivers')

diff --git a/drivers/usb/core/Makefile b/drivers/usb/core/Makefile
index d5503cf..dd1c4d2 100644
--- a/drivers/usb/core/Makefile
+++ b/drivers/usb/core/Makefile
@@ -3,7 +3,7 @@
 #
 
 usbcore-objs	:= usb.o hub.o hcd.o urb.o message.o \
-			config.o file.o buffer.o sysfs.o devio.o
+			config.o file.o buffer.o sysfs.o devio.o notify.o
 
 ifeq ($(CONFIG_PCI),y)
 	usbcore-objs	+= hcd-pci.o
diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 9ad3912..b700b6c 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -792,6 +792,7 @@ static int usb_register_bus(struct usb_bus *bus)
 	list_add (&bus->bus_list, &usb_bus_list);
 	up (&usb_bus_list_lock);
 
+	usb_notify_add_bus(bus);
 	usbfs_add_bus (bus);
 	usbmon_notify_bus_add (bus);
 
@@ -820,6 +821,7 @@ static void usb_deregister_bus (struct usb_bus *bus)
 	list_del (&bus->bus_list);
 	up (&usb_bus_list_lock);
 
+	usb_notify_remove_bus(bus);
 	usbmon_notify_bus_remove (bus);
 	usbfs_remove_bus (bus);
 
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 273e6cc..4f1a8c8 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1128,6 +1128,8 @@ void usb_disconnect(struct usb_device **pdev)
 	 */
 	usb_disable_device(udev, 0);
 
+	usb_notify_remove_device(udev);
+
 	/* Free the device number, remove the /proc/bus/usb entry and
 	 * the sysfs attributes, and delete the parent's children[]
 	 * (or root_hub) pointer.
@@ -1371,6 +1373,7 @@ int usb_new_device(struct usb_device *udev)
 	}
 
 	/* USB device state == configured ... usable */
+	usb_notify_add_device(udev);
 
 	/* add a /proc/bus/usb entry */
 	usbdev_add(udev);
diff --git a/drivers/usb/core/notify.c b/drivers/usb/core/notify.c
new file mode 100644
index 0000000..37da059
--- /dev/null
+++ b/drivers/usb/core/notify.c
@@ -0,0 +1,120 @@
+/*
+ * All the USB notify logic
+ *
+ * (C) Copyright 2005 Greg Kroah-Hartman <gregkh@suse.de>
+ *
+ * notifier functions originally based on those in kernel/sys.c
+ * but fixed up to not be so broken.
+ *
+ */
+
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/notifier.h>
+#ifdef CONFIG_USB_DEBUG
+	#define DEBUG
+#else
+	#undef DEBUG
+#endif
+#include <linux/usb.h>
+
+#include "usb.h"
+
+
+static struct notifier_block *usb_notifier_list;
+static DECLARE_MUTEX(usb_notifier_lock);
+
+static void usb_notifier_chain_register(struct notifier_block **list,
+					struct notifier_block *n)
+{
+	down(&usb_notifier_lock);
+	while (*list) {
+		if (n->priority > (*list)->priority)
+			break;
+		list = &((*list)->next);
+	}
+	n->next = *list;
+	*list = n;
+	up(&usb_notifier_lock);
+}
+
+static void usb_notifier_chain_unregister(struct notifier_block **nl,
+				   struct notifier_block *n)
+{
+	down(&usb_notifier_lock);
+	while ((*nl)!=NULL) {
+		if ((*nl)==n) {
+			*nl = n->next;
+			goto exit;
+		}
+		nl=&((*nl)->next);
+	}
+exit:
+	up(&usb_notifier_lock);
+}
+
+static int usb_notifier_call_chain(struct notifier_block **n,
+				   unsigned long val, void *v)
+{
+	int ret=NOTIFY_DONE;
+	struct notifier_block *nb = *n;
+
+	down(&usb_notifier_lock);
+	while (nb) {
+		ret = nb->notifier_call(nb,val,v);
+		if (ret&NOTIFY_STOP_MASK) {
+			goto exit;
+		}
+		nb = nb->next;
+	}
+exit:
+	up(&usb_notifier_lock);
+	return ret;
+}
+
+/**
+ * usb_register_notify - register a notifier callback whenever a usb change happens
+ * @nb: pointer to the notifier block for the callback events.
+ *
+ * These changes are either USB devices or busses being added or removed.
+ */
+void usb_register_notify(struct notifier_block *nb)
+{
+	usb_notifier_chain_register(&usb_notifier_list, nb);
+}
+EXPORT_SYMBOL_GPL(usb_register_notify);
+
+/**
+ * usb_unregister_notify - unregister a notifier callback
+ * @nb: pointer to the notifier block for the callback events.
+ *
+ * usb_register_notifier() must have been previously called for this function
+ * to work properly.
+ */
+void usb_unregister_notify(struct notifier_block *nb)
+{
+	usb_notifier_chain_unregister(&usb_notifier_list, nb);
+}
+EXPORT_SYMBOL_GPL(usb_unregister_notify);
+
+
+void usb_notify_add_device(struct usb_device *udev)
+{
+	usb_notifier_call_chain(&usb_notifier_list, USB_DEVICE_ADD, udev);
+}
+
+void usb_notify_remove_device(struct usb_device *udev)
+{
+	usb_notifier_call_chain(&usb_notifier_list, USB_DEVICE_REMOVE, udev);
+}
+
+void usb_notify_add_bus(struct usb_bus *ubus)
+{
+	usb_notifier_call_chain(&usb_notifier_list, USB_BUS_ADD, ubus);
+}
+
+void usb_notify_remove_bus(struct usb_bus *ubus)
+{
+	usb_notifier_call_chain(&usb_notifier_list, USB_BUS_REMOVE, ubus);
+}
diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
index 3dc8096..811cf44 100644
--- a/drivers/usb/core/usb.h
+++ b/drivers/usb/core/usb.h
@@ -80,3 +80,9 @@ struct dev_state {
 	unsigned long ifclaimed;
 };
 
+/* internal notify stuff */
+extern void usb_notify_add_device(struct usb_device *udev);
+extern void usb_notify_remove_device(struct usb_device *udev);
+extern void usb_notify_add_bus(struct usb_bus *ubus);
+extern void usb_notify_remove_bus(struct usb_bus *ubus);
+
-- 
cgit v1.1


From a7b986b3e107727dd1c1af0ead0b5e52d7726db3 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: convert usbfs/devio.c to use usb notifiers

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/devio.c | 41 ++++++++++++++++++++++++++++++++++-------
 drivers/usb/core/hub.c   |  2 --
 drivers/usb/core/usb.h   |  2 --
 3 files changed, 34 insertions(+), 11 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index 9222b7a..2bd742b 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -46,6 +46,7 @@
 #include <linux/usb.h>
 #include <linux/usbdevice_fs.h>
 #include <linux/cdev.h>
+#include <linux/notifier.h>
 #include <asm/uaccess.h>
 #include <asm/byteorder.h>
 #include <linux/moduleparam.h>
@@ -1550,7 +1551,7 @@ struct file_operations usbfs_device_file_operations = {
 	.release =	usbdev_release,
 };
 
-void usbdev_add(struct usb_device *dev)
+static void usbdev_add(struct usb_device *dev)
 {
 	int minor = ((dev->bus->busnum-1) * 128) + (dev->devnum-1);
 
@@ -1561,11 +1562,29 @@ void usbdev_add(struct usb_device *dev)
 	dev->class_dev->class_data = dev;
 }
 
-void usbdev_remove(struct usb_device *dev)
+static void usbdev_remove(struct usb_device *dev)
 {
 	class_device_unregister(dev->class_dev);
 }
 
+static int usbdev_notify(struct notifier_block *self, unsigned long action,
+			 void *dev)
+{
+	switch (action) {
+	case USB_DEVICE_ADD:
+		usbdev_add(dev);
+		break;
+	case USB_DEVICE_REMOVE:
+		usbdev_remove(dev);
+		break;
+	}
+	return NOTIFY_OK;
+}
+
+static struct notifier_block usbdev_nb = {
+	.notifier_call = 	usbdev_notify,
+};
+
 static struct cdev usb_device_cdev = {
 	.kobj   = {.name = "usb_device", },
 	.owner  = THIS_MODULE,
@@ -1585,24 +1604,32 @@ int __init usbdev_init(void)
 	retval = cdev_add(&usb_device_cdev, USB_DEVICE_DEV, USB_DEVICE_MAX);
 	if (retval) {
 		err("unable to get usb_device major %d", USB_DEVICE_MAJOR);
-		unregister_chrdev_region(USB_DEVICE_DEV, USB_DEVICE_MAX);
-		goto out;
+		goto error_cdev;
 	}
 	usb_device_class = class_create(THIS_MODULE, "usb_device");
 	if (IS_ERR(usb_device_class)) {
 		err("unable to register usb_device class");
 		retval = PTR_ERR(usb_device_class);
-		usb_device_class = NULL;
-		cdev_del(&usb_device_cdev);
-		unregister_chrdev_region(USB_DEVICE_DEV, USB_DEVICE_MAX);
+		goto error_class;
 	}
 
+	usb_register_notify(&usbdev_nb);
+
 out:
 	return retval;
+
+error_class:
+	usb_device_class = NULL;
+	cdev_del(&usb_device_cdev);
+
+error_cdev:
+	unregister_chrdev_region(USB_DEVICE_DEV, USB_DEVICE_MAX);
+	goto out;
 }
 
 void usbdev_cleanup(void)
 {
+	usb_unregister_notify(&usbdev_nb);
 	class_destroy(usb_device_class);
 	cdev_del(&usb_device_cdev);
 	unregister_chrdev_region(USB_DEVICE_DEV, USB_DEVICE_MAX);
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 4f1a8c8..a9d16af 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1137,7 +1137,6 @@ void usb_disconnect(struct usb_device **pdev)
 	dev_dbg (&udev->dev, "unregistering device\n");
 	release_address(udev);
 	usbfs_remove_device(udev);
-	usbdev_remove(udev);
 	usb_remove_sysfs_dev_files(udev);
 
 	/* Avoid races with recursively_mark_NOTATTACHED() */
@@ -1376,7 +1375,6 @@ int usb_new_device(struct usb_device *udev)
 	usb_notify_add_device(udev);
 
 	/* add a /proc/bus/usb entry */
-	usbdev_add(udev);
 	usbfs_add_device(udev);
 	return 0;
 
diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
index 811cf44..888dbe4 100644
--- a/drivers/usb/core/usb.h
+++ b/drivers/usb/core/usb.h
@@ -62,8 +62,6 @@ extern void usbfs_conn_disc_event(void);
 
 extern int usbdev_init(void);
 extern void usbdev_cleanup(void);
-extern void usbdev_add(struct usb_device *dev);
-extern void usbdev_remove(struct usb_device *dev);
 
 struct dev_state {
 	struct list_head list;      /* state list */
-- 
cgit v1.1


From 54a5c4cd2e4ec0b27c2c3731727f52591456086c Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: convert usbfs/inode.c to use usb notifiers

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/hcd.c   |  2 --
 drivers/usb/core/hcd.h   | 10 ----------
 drivers/usb/core/hub.c   |  3 ---
 drivers/usb/core/inode.c | 44 +++++++++++++++++++++++++++++++-------------
 4 files changed, 31 insertions(+), 28 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index b700b6c..16790ad 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -793,7 +793,6 @@ static int usb_register_bus(struct usb_bus *bus)
 	up (&usb_bus_list_lock);
 
 	usb_notify_add_bus(bus);
-	usbfs_add_bus (bus);
 	usbmon_notify_bus_add (bus);
 
 	dev_info (bus->controller, "new USB bus registered, assigned bus number %d\n", bus->busnum);
@@ -823,7 +822,6 @@ static void usb_deregister_bus (struct usb_bus *bus)
 
 	usb_notify_remove_bus(bus);
 	usbmon_notify_bus_remove (bus);
-	usbfs_remove_bus (bus);
 
 	clear_bit (bus->busnum, busmap.busmap);
 
diff --git a/drivers/usb/core/hcd.h b/drivers/usb/core/hcd.h
index d8f0d29..cc33886 100644
--- a/drivers/usb/core/hcd.h
+++ b/drivers/usb/core/hcd.h
@@ -400,23 +400,13 @@ static inline int hcd_bus_resume (struct usb_bus *bus)
  * these are expected to be called from the USB core/hub thread
  * with the kernel lock held
  */
-extern void usbfs_add_bus(struct usb_bus *bus);
-extern void usbfs_remove_bus(struct usb_bus *bus);
-extern void usbfs_add_device(struct usb_device *dev);
-extern void usbfs_remove_device(struct usb_device *dev);
 extern void usbfs_update_special (void);
-
 extern int usbfs_init(void);
 extern void usbfs_cleanup(void);
 
 #else /* CONFIG_USB_DEVICEFS */
 
-static inline void usbfs_add_bus(struct usb_bus *bus) {}
-static inline void usbfs_remove_bus(struct usb_bus *bus) {}
-static inline void usbfs_add_device(struct usb_device *dev) {}
-static inline void usbfs_remove_device(struct usb_device *dev) {}
 static inline void usbfs_update_special (void) {}
-
 static inline int usbfs_init(void) { return 0; }
 static inline void usbfs_cleanup(void) { }
 
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index a9d16af..6a2ebd8 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1136,7 +1136,6 @@ void usb_disconnect(struct usb_device **pdev)
 	 */
 	dev_dbg (&udev->dev, "unregistering device\n");
 	release_address(udev);
-	usbfs_remove_device(udev);
 	usb_remove_sysfs_dev_files(udev);
 
 	/* Avoid races with recursively_mark_NOTATTACHED() */
@@ -1374,8 +1373,6 @@ int usb_new_device(struct usb_device *udev)
 	/* USB device state == configured ... usable */
 	usb_notify_add_device(udev);
 
-	/* add a /proc/bus/usb entry */
-	usbfs_add_device(udev);
 	return 0;
 
 fail:
diff --git a/drivers/usb/core/inode.c b/drivers/usb/core/inode.c
index d07bba0..12f490f 100644
--- a/drivers/usb/core/inode.c
+++ b/drivers/usb/core/inode.c
@@ -39,6 +39,7 @@
 #include <linux/usbdevice_fs.h>
 #include <linux/smp_lock.h>
 #include <linux/parser.h>
+#include <linux/notifier.h>
 #include <asm/byteorder.h>
 #include "usb.h"
 #include "hcd.h"
@@ -619,7 +620,7 @@ void usbfs_update_special (void)
 	}
 }
 
-void usbfs_add_bus(struct usb_bus *bus)
+static void usbfs_add_bus(struct usb_bus *bus)
 {
 	struct dentry *parent;
 	char name[8];
@@ -642,12 +643,9 @@ void usbfs_add_bus(struct usb_bus *bus)
 		err ("error creating usbfs bus entry");
 		return;
 	}
-
-	usbfs_update_special();
-	usbfs_conn_disc_event();
 }
 
-void usbfs_remove_bus(struct usb_bus *bus)
+static void usbfs_remove_bus(struct usb_bus *bus)
 {
 	if (bus->usbfs_dentry) {
 		fs_remove_file (bus->usbfs_dentry);
@@ -659,12 +657,9 @@ void usbfs_remove_bus(struct usb_bus *bus)
 		remove_special_files();
 		num_buses = 0;
 	}
-
-	usbfs_update_special();
-	usbfs_conn_disc_event();
 }
 
-void usbfs_add_device(struct usb_device *dev)
+static void usbfs_add_device(struct usb_device *dev)
 {
 	char name[8];
 	int i;
@@ -690,12 +685,9 @@ void usbfs_add_device(struct usb_device *dev)
 	}
 	if (dev->usbfs_dentry->d_inode)
 		dev->usbfs_dentry->d_inode->i_size = i_size;
-
-	usbfs_update_special();
-	usbfs_conn_disc_event();
 }
 
-void usbfs_remove_device(struct usb_device *dev)
+static void usbfs_remove_device(struct usb_device *dev)
 {
 	struct dev_state *ds;
 	struct siginfo sinfo;
@@ -716,10 +708,33 @@ void usbfs_remove_device(struct usb_device *dev)
 			kill_proc_info_as_uid(ds->discsignr, &sinfo, ds->disc_pid, ds->disc_uid, ds->disc_euid);
 		}
 	}
+}
+
+static int usbfs_notify(struct notifier_block *self, unsigned long action, void *dev)
+{
+	switch (action) {
+	case USB_DEVICE_ADD:
+		usbfs_add_device(dev);
+		break;
+	case USB_DEVICE_REMOVE:
+		usbfs_remove_device(dev);
+		break;
+	case USB_BUS_ADD:
+		usbfs_add_bus(dev);
+		break;
+	case USB_BUS_REMOVE:
+		usbfs_remove_bus(dev);
+	}
+
 	usbfs_update_special();
 	usbfs_conn_disc_event();
+	return NOTIFY_OK;
 }
 
+static struct notifier_block usbfs_nb = {
+	.notifier_call = 	usbfs_notify,
+};
+
 /* --------------------------------------------------------------------- */
 
 static struct proc_dir_entry *usbdir = NULL;
@@ -732,6 +747,8 @@ int __init usbfs_init(void)
 	if (retval)
 		return retval;
 
+	usb_register_notify(&usbfs_nb);
+
 	/* create mount point for usbfs */
 	usbdir = proc_mkdir("usb", proc_bus);
 
@@ -740,6 +757,7 @@ int __init usbfs_init(void)
 
 void usbfs_cleanup(void)
 {
+	usb_unregister_notify(&usbfs_nb);
 	unregister_filesystem(&usb_fs_type);
 	if (usbdir)
 		remove_proc_entry("usb", proc_bus);
-- 
cgit v1.1


From 72adaa962741e8e910300b66bb123b1a9c31a8a8 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: convert usbmon to use usb notifiers

This also removes 2 usbmon callbacks.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/hcd.c     |  2 --
 drivers/usb/core/hcd.h     | 16 ----------------
 drivers/usb/mon/mon_main.c | 23 +++++++++++++++++++++--
 3 files changed, 21 insertions(+), 20 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 16790ad..e8f2b8d 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -793,7 +793,6 @@ static int usb_register_bus(struct usb_bus *bus)
 	up (&usb_bus_list_lock);
 
 	usb_notify_add_bus(bus);
-	usbmon_notify_bus_add (bus);
 
 	dev_info (bus->controller, "new USB bus registered, assigned bus number %d\n", bus->busnum);
 	return 0;
@@ -821,7 +820,6 @@ static void usb_deregister_bus (struct usb_bus *bus)
 	up (&usb_bus_list_lock);
 
 	usb_notify_remove_bus(bus);
-	usbmon_notify_bus_remove (bus);
 
 	clear_bit (bus->busnum, busmap.busmap);
 
diff --git a/drivers/usb/core/hcd.h b/drivers/usb/core/hcd.h
index cc33886..a5d9294 100644
--- a/drivers/usb/core/hcd.h
+++ b/drivers/usb/core/hcd.h
@@ -421,8 +421,6 @@ struct usb_mon_operations {
 	void (*urb_submit_error)(struct usb_bus *bus, struct urb *urb, int err);
 	void (*urb_complete)(struct usb_bus *bus, struct urb *urb);
 	/* void (*urb_unlink)(struct usb_bus *bus, struct urb *urb); */
-	void (*bus_add)(struct usb_bus *bus);
-	void (*bus_remove)(struct usb_bus *bus);
 };
 
 extern struct usb_mon_operations *mon_ops;
@@ -445,18 +443,6 @@ static inline void usbmon_urb_complete(struct usb_bus *bus, struct urb *urb)
 	if (bus->monitored)
 		(*mon_ops->urb_complete)(bus, urb);
 }
- 
-static inline void usbmon_notify_bus_add(struct usb_bus *bus)
-{
-	if (mon_ops)
-		(*mon_ops->bus_add)(bus);
-}
-
-static inline void usbmon_notify_bus_remove(struct usb_bus *bus)
-{
-	if (mon_ops)
-		(*mon_ops->bus_remove)(bus);
-}
 
 int usb_mon_register(struct usb_mon_operations *ops);
 void usb_mon_deregister(void);
@@ -467,8 +453,6 @@ static inline void usbmon_urb_submit(struct usb_bus *bus, struct urb *urb) {}
 static inline void usbmon_urb_submit_error(struct usb_bus *bus, struct urb *urb,
     int error) {}
 static inline void usbmon_urb_complete(struct usb_bus *bus, struct urb *urb) {}
-static inline void usbmon_notify_bus_add(struct usb_bus *bus) {}
-static inline void usbmon_notify_bus_remove(struct usb_bus *bus) {}
 
 #endif /* CONFIG_USB_MON */
 
diff --git a/drivers/usb/mon/mon_main.c b/drivers/usb/mon/mon_main.c
index 508a210..c34944c 100644
--- a/drivers/usb/mon/mon_main.c
+++ b/drivers/usb/mon/mon_main.c
@@ -11,6 +11,7 @@
 #include <linux/usb.h>
 #include <linux/debugfs.h>
 #include <linux/smp_lock.h>
+#include <linux/notifier.h>
 
 #include "usb_mon.h"
 #include "../core/hcd.h"
@@ -205,6 +206,23 @@ static void mon_bus_remove(struct usb_bus *ubus)
 	up(&mon_lock);
 }
 
+static int mon_notify(struct notifier_block *self, unsigned long action,
+		      void *dev)
+{
+	switch (action) {
+	case USB_BUS_ADD:
+		mon_bus_add(dev);
+		break;
+	case USB_BUS_REMOVE:
+		mon_bus_remove(dev);
+	}
+	return NOTIFY_OK;
+}
+
+static struct notifier_block mon_nb = {
+	.notifier_call = 	mon_notify,
+};
+
 /*
  * Ops
  */
@@ -212,8 +230,6 @@ static struct usb_mon_operations mon_ops_0 = {
 	.urb_submit =	mon_submit,
 	.urb_submit_error = mon_submit_error,
 	.urb_complete =	mon_complete,
-	.bus_add =	mon_bus_add,
-	.bus_remove =	mon_bus_remove,
 };
 
 /*
@@ -329,6 +345,8 @@ static int __init mon_init(void)
 	}
 	// MOD_INC_USE_COUNT(which_module?);
 
+	usb_register_notify(&mon_nb);
+
 	down(&usb_bus_list_lock);
 	list_for_each_entry (ubus, &usb_bus_list, bus_list) {
 		mon_bus_init(mondir, ubus);
@@ -342,6 +360,7 @@ static void __exit mon_exit(void)
 	struct mon_bus *mbus;
 	struct list_head *p;
 
+	usb_unregister_notify(&mon_nb);
 	usb_mon_deregister();
 
 	down(&mon_lock);
-- 
cgit v1.1


From c36fc889b5a4fd66cfd9ba80d9e038745d349567 Mon Sep 17 00:00:00 2001
From: Pete Zaitcev <zaitcev@redhat.com>
Date: Mon, 17 Oct 2005 18:15:54 -0700
Subject: [PATCH] usb: Patch for USBDEVFS_IOCTL from 32-bit programs

Dell supplied me with the following test:

#include<stdio.h>
#include<errno.h>
#include<sys/ioctl.h>
#include<fcntl.h>
#include<linux/usbdevice_fs.h>

main(int argc,char*argv[])
{
   struct usbdevfs_hub_portinfo hubPortInfo = {0};
   struct usbdevfs_ioctl command = {0};
   command.ifno = 0;
   command.ioctl_code = USBDEVFS_HUB_PORTINFO;
   command.data = (void*)&hubPortInfo;
   int fd, ret;
   if(argc != 2) {
     fprintf(stderr,"Usage: %s /proc/bus/usb/<BusNo>/<HubID>\n",argv[0]);
     fprintf(stderr,"Example: %s /proc/bus/usb/001/001\n",argv[0]);
     exit(1);
   }
   errno = 0;
   fd = open(argv[1],O_RDWR);
   if(fd < 0) {
     perror("open failed:");
     exit(errno);
   }
   errno = 0;
   ret = ioctl(fd,USBDEVFS_IOCTL,&command);
   printf("IOCTL return status:%d\n",ret);
   if(ret<0) {
     perror("IOCTL failed:");
     close(fd);
     exit(3);
   } else {
       printf("IOCTL passed:Num of ports %d\n",hubPortInfo.nports);
       close(fd);
       exit(0);
   }
   return 0;
}

I have verified that it breaks if built in 32 bit mode on x86_64 and that
the patch below fixes it.

Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/devio.c | 56 ++++++++++++++++++++++++++++++++++++------------
 1 file changed, 42 insertions(+), 14 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index 2bd742b..ffb2e24 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -1301,23 +1301,20 @@ static int proc_releaseinterface(struct dev_state *ps, void __user *arg)
 	return 0;
 }
 
-static int proc_ioctl (struct dev_state *ps, void __user *arg)
+static int proc_ioctl(struct dev_state *ps, struct usbdevfs_ioctl *ctl)
 {
-	struct usbdevfs_ioctl	ctrl;
 	int			size;
 	void			*buf = NULL;
 	int			retval = 0;
 	struct usb_interface    *intf = NULL;
 	struct usb_driver       *driver = NULL;
 
-	/* get input parameters and alloc buffer */
-	if (copy_from_user(&ctrl, arg, sizeof (ctrl)))
-		return -EFAULT;
-	if ((size = _IOC_SIZE (ctrl.ioctl_code)) > 0) {
+	/* alloc buffer */
+	if ((size = _IOC_SIZE (ctl->ioctl_code)) > 0) {
 		if ((buf = kmalloc (size, GFP_KERNEL)) == NULL)
 			return -ENOMEM;
-		if ((_IOC_DIR(ctrl.ioctl_code) & _IOC_WRITE)) {
-			if (copy_from_user (buf, ctrl.data, size)) {
+		if ((_IOC_DIR(ctl->ioctl_code) & _IOC_WRITE)) {
+			if (copy_from_user (buf, ctl->data, size)) {
 				kfree(buf);
 				return -EFAULT;
 			}
@@ -1333,9 +1330,9 @@ static int proc_ioctl (struct dev_state *ps, void __user *arg)
 
 	if (ps->dev->state != USB_STATE_CONFIGURED)
 		retval = -EHOSTUNREACH;
-	else if (!(intf = usb_ifnum_to_if (ps->dev, ctrl.ifno)))
+	else if (!(intf = usb_ifnum_to_if (ps->dev, ctl->ifno)))
                retval = -EINVAL;
-	else switch (ctrl.ioctl_code) {
+	else switch (ctl->ioctl_code) {
 
 	/* disconnect kernel driver from interface */
 	case USBDEVFS_DISCONNECT:
@@ -1367,7 +1364,7 @@ static int proc_ioctl (struct dev_state *ps, void __user *arg)
 		if (driver == NULL || driver->ioctl == NULL) {
 			retval = -ENOTTY;
 		} else {
-			retval = driver->ioctl (intf, ctrl.ioctl_code, buf);
+			retval = driver->ioctl (intf, ctl->ioctl_code, buf);
 			if (retval == -ENOIOCTLCMD)
 				retval = -ENOTTY;
 		}
@@ -1376,15 +1373,42 @@ static int proc_ioctl (struct dev_state *ps, void __user *arg)
 
 	/* cleanup and return */
 	if (retval >= 0
-			&& (_IOC_DIR (ctrl.ioctl_code) & _IOC_READ) != 0
+			&& (_IOC_DIR (ctl->ioctl_code) & _IOC_READ) != 0
 			&& size > 0
-			&& copy_to_user (ctrl.data, buf, size) != 0)
+			&& copy_to_user (ctl->data, buf, size) != 0)
 		retval = -EFAULT;
 
 	kfree(buf);
 	return retval;
 }
 
+static int proc_ioctl_default(struct dev_state *ps, void __user *arg)
+{
+	struct usbdevfs_ioctl	ctrl;
+
+	if (copy_from_user(&ctrl, arg, sizeof (ctrl)))
+		return -EFAULT;
+	return proc_ioctl(ps, &ctrl);
+}
+
+#ifdef CONFIG_COMPAT
+static int proc_ioctl_compat(struct dev_state *ps, void __user *arg)
+{
+	struct usbdevfs_ioctl32 __user *uioc;
+	struct usbdevfs_ioctl ctrl;
+	u32 udata;
+
+	uioc = compat_ptr(arg);
+	if (get_user(ctrl.ifno, &uioc->ifno) ||
+	    get_user(ctrl.ioctl_code, &uioc->ioctl_code) ||
+	    __get_user(udata, &uioc->data))
+		return -EFAULT;
+	ctrl.data = compat_ptr(udata);
+
+	return proc_ioctl(ps, &ctrl);
+}
+#endif
+
 /*
  * NOTE:  All requests here that have interface numbers as parameters
  * are assuming that somehow the configuration has been prevented from
@@ -1485,6 +1509,10 @@ static int usbdev_ioctl(struct inode *inode, struct file *file, unsigned int cmd
 		ret = proc_reapurbnonblock_compat(ps, p);
 		break;
 
+	case USBDEVFS_IOCTL32:
+		snoop(&dev->dev, "%s: IOCTL\n", __FUNCTION__);
+		ret = proc_ioctl_compat(ps, p);
+		break;
 #endif
 
 	case USBDEVFS_DISCARDURB:
@@ -1519,7 +1547,7 @@ static int usbdev_ioctl(struct inode *inode, struct file *file, unsigned int cmd
 
 	case USBDEVFS_IOCTL:
 		snoop(&dev->dev, "%s: IOCTL\n", __FUNCTION__);
-		ret = proc_ioctl(ps, p);
+		ret = proc_ioctl_default(ps, p);
 		break;
 	}
 	usb_unlock_device(dev);
-- 
cgit v1.1


From a6c82600d4058346ea6fd801bc21d7abcc1350d8 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: delete the bluetty driver

We have a real Bluetooth system in Linux, lets finally delete this driver as no
one is using it (and if they are, they are using a closed source bluetooth
stack, which I can't support anyway.)

Marcel, you owe me a beer :)

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/Makefile        |    1 -
 drivers/usb/class/Kconfig   |   23 -
 drivers/usb/class/Makefile  |    1 -
 drivers/usb/class/bluetty.c | 1279 -------------------------------------------
 4 files changed, 1304 deletions(-)
 delete mode 100644 drivers/usb/class/bluetty.c

(limited to 'drivers')

diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
index aa554f9..a50c2bc 100644
--- a/drivers/usb/Makefile
+++ b/drivers/usb/Makefile
@@ -18,7 +18,6 @@ obj-$(CONFIG_ETRAX_USB_HOST)	+= host/
 
 obj-$(CONFIG_USB_ACM)		+= class/
 obj-$(CONFIG_USB_AUDIO)		+= class/
-obj-$(CONFIG_USB_BLUETOOTH_TTY)	+= class/
 obj-$(CONFIG_USB_MIDI)		+= class/
 obj-$(CONFIG_USB_PRINTER)	+= class/
 
diff --git a/drivers/usb/class/Kconfig b/drivers/usb/class/Kconfig
index 333e39b..ef105a9 100644
--- a/drivers/usb/class/Kconfig
+++ b/drivers/usb/class/Kconfig
@@ -28,29 +28,6 @@ config USB_AUDIO
 	  To compile this driver as a module, choose M here: the
 	  module will be called audio.
 
-comment "USB Bluetooth TTY can only be used with disabled Bluetooth subsystem"
-	depends on USB && BT
-
-config USB_BLUETOOTH_TTY
-	tristate "USB Bluetooth TTY support"
-	depends on USB && BT=n
-	---help---
-	  This driver implements a nonstandard tty interface to a Bluetooth
-	  device that can be used only by specialized Bluetooth HCI software.
-
-	  Say Y here if you want to use OpenBT Bluetooth stack (available
-	  at <http://developer.axis.com/software>), or other TTY based
-	  Bluetooth stacks, and want to connect a USB Bluetooth device
-	  to your computer's USB port.
-
-	  Do *not* enable this driver if you want to use generic Linux
-	  Bluetooth support.
-
-	  If in doubt, say N here.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called bluetty.
-
 config USB_MIDI
 	tristate "USB MIDI support"
 	depends on USB && SOUND && OBSOLETE_OSS_USB_DRIVER
diff --git a/drivers/usb/class/Makefile b/drivers/usb/class/Makefile
index 971e549..2294712 100644
--- a/drivers/usb/class/Makefile
+++ b/drivers/usb/class/Makefile
@@ -5,6 +5,5 @@
 
 obj-$(CONFIG_USB_ACM)		+= cdc-acm.o
 obj-$(CONFIG_USB_AUDIO)		+= audio.o
-obj-$(CONFIG_USB_BLUETOOTH_TTY)	+= bluetty.o
 obj-$(CONFIG_USB_MIDI)		+= usb-midi.o
 obj-$(CONFIG_USB_PRINTER)	+= usblp.o
diff --git a/drivers/usb/class/bluetty.c b/drivers/usb/class/bluetty.c
deleted file mode 100644
index 5240233..0000000
--- a/drivers/usb/class/bluetty.c
+++ /dev/null
@@ -1,1279 +0,0 @@
-/*
- * bluetty.c   Version 0.13
- *
- * Copyright (C) 2000, 2001 Greg Kroah-Hartman	<greg@kroah.com>
- * Copyright (C) 2000 Mark Douglas Corner	<mcorner@umich.edu>
- *
- * USB Bluetooth TTY driver, based on the Bluetooth Spec version 1.0B
- * 
- * (2001/11/30) Version 0.13 gkh
- *	- added locking patch from Masoodur Rahman <rmasoodu@in.ibm.com>
- *	- removed active variable, as open_count will do.
- *
- * (2001/07/09) Version 0.12 gkh
- *	- removed in_interrupt() call, as it doesn't make sense to do 
- *	  that anymore.
- *
- * (2001/06/05) Version 0.11 gkh
- *	- Fixed problem with read urb status saying that we have shutdown,
- *	  and that we shouldn't resubmit the urb.  Patch from unknown.
- *
- * (2001/05/28) Version 0.10 gkh
- *	- Fixed problem with using data from userspace in the bluetooth_write
- *	  function as found by the CHECKER project.
- *	- Added a buffer to the write_urb_pool which reduces the number of
- *	  buffers being created and destroyed for ever write.  Also cleans
- *	  up the logic a bit.
- *	- Added a buffer to the control_urb_pool which fixes a memory leak
- *	  when the device is removed from the system.
- *
- * (2001/05/28) Version 0.9 gkh
- *	Fixed problem with bluetooth==NULL for bluetooth_read_bulk_callback
- *	which was found by both the CHECKER project and Mikko Rahkonen.
- *
- * (08/04/2001) gb
- *	Identify version on module load.
- *
- * (2001/03/10) Version 0.8 gkh
- *	Fixed problem with not unlinking interrupt urb on device close
- *	and resubmitting the read urb on error with bluetooth struct.
- *	Thanks to Narayan Mohanram <narayan@RovingNetworks.com> for the
- *	fixes.
- *
- * (11/29/2000) Version 0.7 gkh
- *	Fixed problem with overrunning the tty flip buffer.
- *	Removed unneeded NULL pointer initialization.
- *
- * (10/05/2000) Version 0.6 gkh
- *	Fixed bug with urb->dev not being set properly, now that the usb
- *	core needs it.
- *	Got a real major id number and name.
- *
- * (08/06/2000) Version 0.5 gkh
- *	Fixed problem of not resubmitting the bulk read urb if there is
- *	an error in the callback.  Ericsson devices seem to need this.
- *
- * (07/11/2000) Version 0.4 gkh
- *	Fixed bug in disconnect for when we call tty_hangup
- *	Fixed bug in bluetooth_ctrl_msg where the bluetooth struct was not
- *	getting attached to the control urb properly.
- *	Fixed bug in bluetooth_write where we pay attention to the result
- *	of bluetooth_ctrl_msg.
- *
- * (08/03/2000) Version 0.3 gkh mdc
- *	Merged in Mark's changes to make the driver play nice with the Axis
- *	stack.
- *	Made the write bulk use an urb pool to enable larger transfers with
- *	fewer calls to the driver.
- *	Fixed off by one bug in acl pkt receive
- *	Made packet counters specific to each bluetooth device 
- *	Added checks for zero length callbacks
- *	Added buffers for int and bulk packets.  Had to do this otherwise 
- *	packet types could intermingle.
- *	Made a control urb pool for the control messages.
- *
- * (07/11/2000) Version 0.2 gkh
- *	Fixed a small bug found by Nils Faerber in the usb_bluetooth_probe 
- *	function.
- *
- * (07/09/2000) Version 0.1 gkh
- *	Initial release. Has support for sending ACL data (which is really just
- *	a HCI frame.) Raw HCI commands and HCI events are not supported.
- *	A ioctl will probably be needed for the HCI commands and events in the
- *	future. All isoch endpoints are ignored at this time also.
- *	This driver should work for all currently shipping USB Bluetooth 
- *	devices at this time :)
- * 
- */
-
-/*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/tty.h>
-#include <linux/tty_driver.h>
-#include <linux/tty_flip.h>
-#include <linux/module.h>
-#include <asm/uaccess.h>
-
-#define DEBUG
-#include <linux/usb.h>
-
-/*
- * Version Information
- */
-#define DRIVER_VERSION "v0.13"
-#define DRIVER_AUTHOR "Greg Kroah-Hartman, Mark Douglas Corner"
-#define DRIVER_DESC "USB Bluetooth tty driver"
-
-/* define this if you have hardware that is not good */
-/*#define	BTBUGGYHARDWARE */
-
-/* Class, SubClass, and Protocol codes that describe a Bluetooth device */
-#define WIRELESS_CLASS_CODE			0xe0
-#define RF_SUBCLASS_CODE			0x01
-#define BLUETOOTH_PROGRAMMING_PROTOCOL_CODE	0x01
-
-
-#define BLUETOOTH_TTY_MAJOR	216	/* real device node major id */
-#define BLUETOOTH_TTY_MINORS	256	/* whole lotta bluetooth devices */
-
-#define USB_BLUETOOTH_MAGIC	0x6d02	/* magic number for bluetooth struct */
-
-#define BLUETOOTH_CONTROL_REQUEST_TYPE	0x20
-
-/* Bluetooth packet types */
-#define CMD_PKT			0x01
-#define ACL_PKT			0x02
-#define SCO_PKT			0x03
-#define EVENT_PKT		0x04
-#define ERROR_PKT		0x05
-#define NEG_PKT			0x06
-
-/* Message sizes */
-#define MAX_EVENT_SIZE		0xFF
-#define EVENT_HDR_SIZE		3	/* 2 for the header + 1 for the type indicator */
-#define EVENT_BUFFER_SIZE	(MAX_EVENT_SIZE + EVENT_HDR_SIZE)
-
-#define MAX_ACL_SIZE		0xFFFF
-#define ACL_HDR_SIZE		5	/* 4 for the header + 1 for the type indicator */
-#define ACL_BUFFER_SIZE		(MAX_ACL_SIZE + ACL_HDR_SIZE)
-
-/* parity check flag */
-#define RELEVANT_IFLAG(iflag)	(iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
-
-#define CHAR2INT16(c1,c0)	(((u32)((c1) & 0xff) << 8) + (u32)((c0) & 0xff))
-
-#define NUM_BULK_URBS		24
-#define NUM_CONTROL_URBS	16
-
-struct usb_bluetooth {
-	int			magic;
-	struct usb_device *	dev;
-	struct tty_driver *	tty_driver;	/* the tty_driver for this device */
-	struct tty_struct *	tty;		/* the corresponding tty for this port */
-
-	unsigned char		minor;		/* the starting minor number for this device */
-	int			throttle;	/* throttled by tty layer */
-	int			open_count;
-	
-	__u8			control_out_bInterfaceNum;
-	struct urb *		control_urb_pool[NUM_CONTROL_URBS];
-	struct usb_ctrlrequest	dr[NUM_CONTROL_URBS];
-
-	unsigned char *		interrupt_in_buffer;
-	struct urb *		interrupt_in_urb;
-	__u8			interrupt_in_endpointAddress;
-	__u8			interrupt_in_interval;
-	int			interrupt_in_buffer_size;
-
-	unsigned char *		bulk_in_buffer;
-	struct urb *		read_urb;
-	__u8			bulk_in_endpointAddress;
-	int			bulk_in_buffer_size;
-
-	int			bulk_out_buffer_size;
-	__u8			bulk_out_endpointAddress;
-
-	wait_queue_head_t	write_wait;
-
-	struct work_struct			work;	/* work queue entry for line discipline waking up */
-	
-	unsigned int		int_packet_pos;
-	unsigned char		int_buffer[EVENT_BUFFER_SIZE];
-	unsigned int		bulk_packet_pos;
-	unsigned char		bulk_buffer[ACL_BUFFER_SIZE];	/* 64k preallocated, fix? */
-	struct semaphore	lock;
-};
-
-
-/* local function prototypes */
-static int  bluetooth_open		(struct tty_struct *tty, struct file *filp);
-static void bluetooth_close		(struct tty_struct *tty, struct file *filp);
-static int  bluetooth_write		(struct tty_struct *tty, const unsigned char *buf, int count);
-static int  bluetooth_write_room	(struct tty_struct *tty);
-static int  bluetooth_chars_in_buffer	(struct tty_struct *tty);
-static void bluetooth_throttle		(struct tty_struct *tty);
-static void bluetooth_unthrottle	(struct tty_struct *tty);
-static int  bluetooth_ioctl		(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
-static void bluetooth_set_termios	(struct tty_struct *tty, struct termios *old);
-
-static void bluetooth_int_callback		(struct urb *urb, struct pt_regs *regs);
-static void bluetooth_ctrl_callback		(struct urb *urb, struct pt_regs *regs);
-static void bluetooth_read_bulk_callback	(struct urb *urb, struct pt_regs *regs);
-static void bluetooth_write_bulk_callback	(struct urb *urb, struct pt_regs *regs);
-
-static int usb_bluetooth_probe (struct usb_interface *intf, 
-				const struct usb_device_id *id);
-static void usb_bluetooth_disconnect	(struct usb_interface *intf);
-
-
-static struct usb_device_id usb_bluetooth_ids [] = {
-	{ USB_DEVICE_INFO(WIRELESS_CLASS_CODE, RF_SUBCLASS_CODE, BLUETOOTH_PROGRAMMING_PROTOCOL_CODE) },
-	{ }						/* Terminating entry */
-};
-
-MODULE_DEVICE_TABLE (usb, usb_bluetooth_ids);
-
-static struct usb_driver usb_bluetooth_driver = {
-	.owner =	THIS_MODULE,
-	.name =		"bluetty",
-	.probe =	usb_bluetooth_probe,
-	.disconnect =	usb_bluetooth_disconnect,
-	.id_table =	usb_bluetooth_ids,
-};
-
-static struct tty_driver	*bluetooth_tty_driver;
-static struct usb_bluetooth	*bluetooth_table[BLUETOOTH_TTY_MINORS];
-
-
-static inline int bluetooth_paranoia_check (struct usb_bluetooth *bluetooth, const char *function)
-{
-	if (!bluetooth) {
-		dbg("%s - bluetooth == NULL", function);
-		return -1;
-	}
-	if (bluetooth->magic != USB_BLUETOOTH_MAGIC) {
-		dbg("%s - bad magic number for bluetooth", function);
-		return -1;
-	}
-
-	return 0;
-}
-
-
-static inline struct usb_bluetooth* get_usb_bluetooth (struct usb_bluetooth *bluetooth, const char *function)
-{
-	if (!bluetooth || 
-	    bluetooth_paranoia_check (bluetooth, function)) { 
-		/* then say that we don't have a valid usb_bluetooth thing, which will
-		 * end up generating -ENODEV return values */
-		return NULL;
-	}
-
-	return bluetooth;
-}
-
-
-static inline struct usb_bluetooth *get_bluetooth_by_index (int index)
-{
-	return bluetooth_table[index];
-}
-
-
-static int bluetooth_ctrl_msg (struct usb_bluetooth *bluetooth, int request, int value, const unsigned char *buf, int len)
-{
-	struct urb *urb = NULL;
-	struct usb_ctrlrequest *dr = NULL;
-	int i;
-	int status;
-
-	dbg ("%s", __FUNCTION__);
-
-	/* try to find a free urb in our list */
-	for (i = 0; i < NUM_CONTROL_URBS; ++i) {
-		if (bluetooth->control_urb_pool[i]->status != -EINPROGRESS) {
-			urb = bluetooth->control_urb_pool[i];
-			dr = &bluetooth->dr[i];
-			break;
-		}
-	}
-	if (urb == NULL) {
-		dbg ("%s - no free urbs", __FUNCTION__);
-		return -ENOMEM;
-	}
-
-	/* keep increasing the urb transfer buffer to fit the size of the message */
-	if (urb->transfer_buffer == NULL) {
-		urb->transfer_buffer = kmalloc (len, GFP_KERNEL);
-		if (urb->transfer_buffer == NULL) {
-			err ("%s - out of memory", __FUNCTION__);
-			return -ENOMEM;
-		}
-	}
-	if (urb->transfer_buffer_length < len) {
-		kfree(urb->transfer_buffer);
-		urb->transfer_buffer = kmalloc (len, GFP_KERNEL);
-		if (urb->transfer_buffer == NULL) {
-			err ("%s - out of memory", __FUNCTION__);
-			return -ENOMEM;
-		}
-	}
-	memcpy (urb->transfer_buffer, buf, len);
-
-	dr->bRequestType= BLUETOOTH_CONTROL_REQUEST_TYPE;
-	dr->bRequest = request;
-	dr->wValue = cpu_to_le16((u16) value);
-	dr->wIndex = cpu_to_le16((u16) bluetooth->control_out_bInterfaceNum);
-	dr->wLength = cpu_to_le16((u16) len);
-	
-	usb_fill_control_urb (urb, bluetooth->dev, usb_sndctrlpipe(bluetooth->dev, 0),
-			  (unsigned char*)dr, urb->transfer_buffer, len, bluetooth_ctrl_callback, bluetooth);
-
-	/* send it down the pipe */
-	status = usb_submit_urb(urb, GFP_KERNEL);
-	if (status)
-		dbg("%s - usb_submit_urb(control) failed with status = %d", __FUNCTION__, status);
-	
-	return status;
-}
-
-
-
-
-
-/*****************************************************************************
- * Driver tty interface functions
- *****************************************************************************/
-static int bluetooth_open (struct tty_struct *tty, struct file * filp)
-{
-	struct usb_bluetooth *bluetooth;
-	int result;
-
-	dbg("%s", __FUNCTION__);
-
-	/* initialize the pointer incase something fails */
-	tty->driver_data = NULL;
-
-	/* get the bluetooth object associated with this tty pointer */
-	bluetooth = get_bluetooth_by_index (tty->index);
-
-	if (bluetooth_paranoia_check (bluetooth, __FUNCTION__)) {
-		return -ENODEV;
-	}
-
-	down (&bluetooth->lock);
- 
-	++bluetooth->open_count;
-	if (bluetooth->open_count == 1) {
-		/* set up our structure making the tty driver remember our object, and us it */
-		tty->driver_data = bluetooth;
-		bluetooth->tty = tty;
-
-		/* force low_latency on so that our tty_push actually forces the data through, 
-	 	* otherwise it is scheduled, and with high data rates (like with OHCI) data
-	 	* can get lost. */
-		bluetooth->tty->low_latency = 1;
-	
-		/* Reset the packet position counters */
-		bluetooth->int_packet_pos = 0;
-		bluetooth->bulk_packet_pos = 0;
-
-#ifndef BTBUGGYHARDWARE
-		/* Start reading from the device */
-		usb_fill_bulk_urb (bluetooth->read_urb, bluetooth->dev, 
-			       usb_rcvbulkpipe(bluetooth->dev, bluetooth->bulk_in_endpointAddress),
-			       bluetooth->bulk_in_buffer,
-			       bluetooth->bulk_in_buffer_size,
-			       bluetooth_read_bulk_callback, bluetooth);
-		result = usb_submit_urb(bluetooth->read_urb, GFP_KERNEL);
-		if (result)
-			dbg("%s - usb_submit_urb(read bulk) failed with status %d", __FUNCTION__, result);
-#endif
-		usb_fill_int_urb (bluetooth->interrupt_in_urb, bluetooth->dev,
-			      usb_rcvintpipe(bluetooth->dev, bluetooth->interrupt_in_endpointAddress),
-			      bluetooth->interrupt_in_buffer,
-			      bluetooth->interrupt_in_buffer_size,
-			      bluetooth_int_callback, bluetooth,
-			      bluetooth->interrupt_in_interval);
-		result = usb_submit_urb(bluetooth->interrupt_in_urb, GFP_KERNEL);
-		if (result)
-			dbg("%s - usb_submit_urb(interrupt in) failed with status %d", __FUNCTION__, result);
-	}
-	
-	up(&bluetooth->lock);
-
-	return 0;
-}
-
-
-static void bluetooth_close (struct tty_struct *tty, struct file * filp)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)tty->driver_data, __FUNCTION__);
-
-	if (!bluetooth) {
-		return;
-	}
-
-	dbg("%s", __FUNCTION__);
-
-	if (!bluetooth->open_count) {
-		dbg ("%s - device not opened", __FUNCTION__);
-		return;
-	}
-
-	down (&bluetooth->lock);
- 
-	--bluetooth->open_count;
-	if (bluetooth->open_count <= 0) {
-		bluetooth->open_count = 0;
-
-		/* shutdown any in-flight urbs that we know about */
-		usb_kill_urb (bluetooth->read_urb);
-		usb_kill_urb (bluetooth->interrupt_in_urb);
-	}
-	up(&bluetooth->lock);
-}
-
-
-static int bluetooth_write (struct tty_struct * tty, const unsigned char *buf, int count)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)tty->driver_data, __FUNCTION__);
-	struct urb *urb = NULL;
-	unsigned char *temp_buffer = NULL;
-	const unsigned char *current_buffer;
-	unsigned char *urb_buffer;
-	int i;
-	int retval = 0;
-
-	if (!bluetooth) {
-		return -ENODEV;
-	}
-
-	dbg("%s - %d byte(s)", __FUNCTION__, count);
-
-	if (!bluetooth->open_count) {
-		dbg ("%s - device not opened", __FUNCTION__);
-		return -EINVAL;
-	}
-
-	if (count == 0) {
-		dbg("%s - write request of 0 bytes", __FUNCTION__);
-		return 0;
-	}
-	if (count == 1) {
-		dbg("%s - write request only included type %d", __FUNCTION__, buf[0]);
-		return 1;
-	}
-
-#ifdef DEBUG
-	printk (KERN_DEBUG __FILE__ ": %s - length = %d, data = ", __FUNCTION__, count);
-	for (i = 0; i < count; ++i) {
-		printk ("%.2x ", buf[i]);
-	}
-	printk ("\n");
-#endif
-
-	current_buffer = buf;
-
-	switch (*current_buffer) {
-		/* First byte indicates the type of packet */
-		case CMD_PKT:
-			/* dbg("%s- Send cmd_pkt len:%d", __FUNCTION__, count);*/
-
-			retval = bluetooth_ctrl_msg (bluetooth, 0x00, 0x00, &current_buffer[1], count-1);
-			if (retval) {
-				goto exit;
-			}
-			retval = count;
-			break;
-
-		case ACL_PKT:
-			++current_buffer;
-			--count;
-
-			urb_buffer = kmalloc (count, GFP_ATOMIC);
-			if (!urb_buffer) {
-				dev_err(&bluetooth->dev->dev, "out of memory\n");
-				retval = -ENOMEM;
-				goto exit;
-			}
-
-			urb = usb_alloc_urb(0, GFP_ATOMIC);
-			if (!urb) {
-				dev_err(&bluetooth->dev->dev, "no more free urbs\n");
-				kfree(urb_buffer);
-				retval = -ENOMEM;
-				goto exit;
-			}
-			memcpy (urb_buffer, current_buffer, count);
-
-			/* build up our urb */
-			usb_fill_bulk_urb(urb, bluetooth->dev, 
-					  usb_sndbulkpipe(bluetooth->dev,
-						  	  bluetooth->bulk_out_endpointAddress),
-					  urb_buffer,
-					  count,
-					  bluetooth_write_bulk_callback,
-					  bluetooth);
-
-
-			/* send it down the pipe */
-			retval = usb_submit_urb(urb, GFP_KERNEL);
-			if (retval) {
-				dbg("%s - usb_submit_urb(write bulk) failed with error = %d", __FUNCTION__, retval);
-				goto exit;
-			}
-
-			/* we are done with this urb, so let the host driver
-			 * really free it when it is finished with it */
-			usb_free_urb (urb);
-			retval = count + 1;
-			break;
-		
-		default :
-			dbg("%s - unsupported (at this time) write type", __FUNCTION__);
-			retval = -EINVAL;
-			break;
-	}
-
-exit:
-	kfree(temp_buffer);
-
-	return retval;
-} 
-
-
-static int bluetooth_write_room (struct tty_struct *tty) 
-{
-	dbg("%s", __FUNCTION__);
-
-	/*
-	 * We really can take anything the user throws at us
-	 * but let's pick a nice big number to tell the tty
-	 * layer that we have lots of free space
-	 */
-	return 2048;
-}
-
-
-static int bluetooth_chars_in_buffer (struct tty_struct *tty) 
-{
-	dbg("%s", __FUNCTION__);
-
-	/* 
-	 * We can't really account for how much data we
-	 * have sent out, but hasn't made it through to the
-	 * device, so just tell the tty layer that everything
-	 * is flushed.
-	 */
-	return 0;
-}
-
-
-static void bluetooth_throttle (struct tty_struct * tty)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)tty->driver_data, __FUNCTION__);
-
-	if (!bluetooth) {
-		return;
-	}
-
-	dbg("%s", __FUNCTION__);
-
-	if (!bluetooth->open_count) {
-		dbg ("%s - device not open", __FUNCTION__);
-		return;
-	}
-	
-	dbg("%s unsupported (at this time)", __FUNCTION__);
-
-	return;
-}
-
-
-static void bluetooth_unthrottle (struct tty_struct * tty)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)tty->driver_data, __FUNCTION__);
-
-	if (!bluetooth) {
-		return;
-	}
-
-	dbg("%s", __FUNCTION__);
-
-	if (!bluetooth->open_count) {
-		dbg ("%s - device not open", __FUNCTION__);
-		return;
-	}
-
-	dbg("%s unsupported (at this time)", __FUNCTION__);
-}
-
-
-static int bluetooth_ioctl (struct tty_struct *tty, struct file * file, unsigned int cmd, unsigned long arg)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)tty->driver_data, __FUNCTION__);
-
-	if (!bluetooth) {
-		return -ENODEV;
-	}
-
-	dbg("%s - cmd 0x%.4x", __FUNCTION__, cmd);
-
-	if (!bluetooth->open_count) {
-		dbg ("%s - device not open", __FUNCTION__);
-		return -ENODEV;
-	}
-
-	/* FIXME!!! */
-	return -ENOIOCTLCMD;
-}
-
-
-static void bluetooth_set_termios (struct tty_struct *tty, struct termios * old)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)tty->driver_data, __FUNCTION__);
-
-	if (!bluetooth) {
-		return;
-	}
-
-	dbg("%s", __FUNCTION__);
-
-	if (!bluetooth->open_count) {
-		dbg ("%s - device not open", __FUNCTION__);
-		return;
-	}
-
-	/* FIXME!!! */
-
-	return;
-}
-
-
-#ifdef BTBUGGYHARDWARE
-void btusb_enable_bulk_read(struct tty_struct *tty){
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)tty->driver_data, __FUNCTION__);
-	int result;
-
-	if (!bluetooth) {
-		return;
-	}
-
-	dbg("%s", __FUNCTION__);
-
-	if (!bluetooth->open_count) {
-		dbg ("%s - device not open", __FUNCTION__);
-		return;
-	}
-
-	if (bluetooth->read_urb) {
-		usb_fill_bulk_urb(bluetooth->read_urb, bluetooth->dev, 
-			      usb_rcvbulkpipe(bluetooth->dev, bluetooth->bulk_in_endpointAddress),
-			      bluetooth->bulk_in_buffer, bluetooth->bulk_in_buffer_size, 
-			      bluetooth_read_bulk_callback, bluetooth);
-		result = usb_submit_urb(bluetooth->read_urb, GFP_KERNEL);
-		if (result)
-			err ("%s - failed submitting read urb, error %d", __FUNCTION__, result);
-	}
-}
-
-void btusb_disable_bulk_read(struct tty_struct *tty){
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)tty->driver_data, __FUNCTION__);
-
-	if (!bluetooth) {
-		return;
-	}
-
-	dbg("%s", __FUNCTION__);
-
-	if (!bluetooth->open_count) {
-		dbg ("%s - device not open", __FUNCTION__);
-		return;
-	}
-
-	if ((bluetooth->read_urb) && (bluetooth->read_urb->actual_length))
-		usb_kill_urb(bluetooth->read_urb);
-}
-#endif
-
-
-/*****************************************************************************
- * urb callback functions
- *****************************************************************************/
-
-
-static void bluetooth_int_callback (struct urb *urb, struct pt_regs *regs)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)urb->context, __FUNCTION__);
-	unsigned char *data = urb->transfer_buffer;
-	unsigned int i;
-	unsigned int count = urb->actual_length;
-	unsigned int packet_size;
-	int status;
-
-	dbg("%s", __FUNCTION__);
-
-	if (!bluetooth) {
-		dbg("%s - bad bluetooth pointer, exiting", __FUNCTION__);
-		return;
-	}
-
-	switch (urb->status) {
-	case 0:
-		/* success */
-		break;
-	case -ECONNRESET:
-	case -ENOENT:
-	case -ESHUTDOWN:
-		/* this urb is terminated, clean up */
-		dbg("%s - urb shutting down with status: %d", __FUNCTION__, urb->status);
-		return;
-	default:
-		dbg("%s - nonzero urb status received: %d", __FUNCTION__, urb->status);
-		goto exit;
-	}
-
-	if (!count) {
-		dbg("%s - zero length int", __FUNCTION__);
-		goto exit;
-	}
-
-
-#ifdef DEBUG
-	if (count) {
-		printk (KERN_DEBUG __FILE__ ": %s- length = %d, data = ", __FUNCTION__, count);
-		for (i = 0; i < count; ++i) {
-			printk ("%.2x ", data[i]);
-		}
-		printk ("\n");
-	}
-#endif
-
-#ifdef BTBUGGYHARDWARE
-	if ((count >= 2) && (data[0] == 0xFF) && (data[1] == 0x00)) {
-		data += 2;
-		count -= 2;
-	}
-	if (count == 0) {
-		urb->actual_length = 0;
-		goto exit;
-	}
-#endif
-	/* We add  a packet type identifier to the beginning of each
-	   HCI frame.  This makes the data in the tty look like a
-	   serial USB devices.  Each HCI frame can be broken across
-	   multiple URBs so we buffer them until we have a full hci
-	   packet */
-
-	if (!bluetooth->int_packet_pos) {
-		bluetooth->int_buffer[0] = EVENT_PKT;
-		bluetooth->int_packet_pos++;
-	}
-	
-	if (bluetooth->int_packet_pos + count > EVENT_BUFFER_SIZE) {
-		err("%s - exceeded EVENT_BUFFER_SIZE", __FUNCTION__);
-		bluetooth->int_packet_pos = 0;
-		goto exit;
-	}
-
-	memcpy (&bluetooth->int_buffer[bluetooth->int_packet_pos],
-		urb->transfer_buffer, count);
-	bluetooth->int_packet_pos += count;
-	urb->actual_length = 0;
-
-	if (bluetooth->int_packet_pos >= EVENT_HDR_SIZE)
-		packet_size = bluetooth->int_buffer[2];
-	else
-		goto exit;
-
-	if (packet_size + EVENT_HDR_SIZE < bluetooth->int_packet_pos) {
-		err("%s - packet was too long", __FUNCTION__);
-		bluetooth->int_packet_pos = 0;
-		goto exit;
-	}
-
-	if (packet_size + EVENT_HDR_SIZE == bluetooth->int_packet_pos) {
-		for (i = 0; i < bluetooth->int_packet_pos; ++i) {
-			/* if we insert more than TTY_FLIPBUF_SIZE characters, we drop them */
-			if (bluetooth->tty->flip.count >= TTY_FLIPBUF_SIZE) {
-				tty_flip_buffer_push(bluetooth->tty);
-			}
-			tty_insert_flip_char(bluetooth->tty, bluetooth->int_buffer[i], 0);
-		}
-		tty_flip_buffer_push(bluetooth->tty);
-
-		bluetooth->int_packet_pos = 0;
-	}
-
-exit:
-	status = usb_submit_urb (urb, GFP_ATOMIC);
-	if (status)
-		err ("%s - usb_submit_urb failed with result %d",
-		     __FUNCTION__, status);
-}
-
-
-static void bluetooth_ctrl_callback (struct urb *urb, struct pt_regs *regs)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)urb->context, __FUNCTION__);
-
-	dbg("%s", __FUNCTION__);
-
-	if (!bluetooth) {
-		dbg("%s - bad bluetooth pointer, exiting", __FUNCTION__);
-		return;
-	}
-
-	if (urb->status) {
-		dbg("%s - nonzero read bulk status received: %d", __FUNCTION__, urb->status);
-		return;
-	}
-}
-
-
-static void bluetooth_read_bulk_callback (struct urb *urb, struct pt_regs *regs)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)urb->context, __FUNCTION__);
-	unsigned char *data = urb->transfer_buffer;
-	unsigned int count = urb->actual_length;
-	unsigned int i;
-	unsigned int packet_size;
-	int result;
-
-
-	dbg("%s", __FUNCTION__);
-
-	if (!bluetooth) {
-		dbg("%s - bad bluetooth pointer, exiting", __FUNCTION__);
-		return;
-	}
-
-	if (urb->status) {
-		dbg("%s - nonzero read bulk status received: %d", __FUNCTION__, urb->status);
-		if (urb->status == -ENOENT) {                   
-			dbg("%s - URB canceled, won't reschedule", __FUNCTION__);
-			return;
-		}
-		goto exit;
-	}
-
-	if (!count) {
-		dbg("%s - zero length read bulk", __FUNCTION__);
-		goto exit;
-	}
-
-#ifdef DEBUG
-	if (count) {
-		printk (KERN_DEBUG __FILE__ ": %s- length = %d, data = ", __FUNCTION__, count);
-		for (i = 0; i < count; ++i) {
-			printk ("%.2x ", data[i]);
-		}
-		printk ("\n");
-	}
-#endif
-#ifdef BTBUGGYHARDWARE
-	if ((count == 4) && (data[0] == 0x00) && (data[1] == 0x00)
-	    && (data[2] == 0x00) && (data[3] == 0x00)) {
-		urb->actual_length = 0;
-		usb_fill_bulk_urb(bluetooth->read_urb, bluetooth->dev, 
-			      usb_rcvbulkpipe(bluetooth->dev, bluetooth->bulk_in_endpointAddress),
-			      bluetooth->bulk_in_buffer, bluetooth->bulk_in_buffer_size, 
-			      bluetooth_read_bulk_callback, bluetooth);
-		result = usb_submit_urb(bluetooth->read_urb, GFP_KERNEL);
-		if (result)
-			err ("%s - failed resubmitting read urb, error %d", __FUNCTION__, result);
-
-		return;
-	}
-#endif
-	/* We add  a packet type identifier to the beginning of each
-	   HCI frame.  This makes the data in the tty look like a
-	   serial USB devices.  Each HCI frame can be broken across
-	   multiple URBs so we buffer them until we have a full hci
-	   packet */
-	
-	if (!bluetooth->bulk_packet_pos) {
-		bluetooth->bulk_buffer[0] = ACL_PKT;
-		bluetooth->bulk_packet_pos++;
-	}
-
-	if (bluetooth->bulk_packet_pos + count > ACL_BUFFER_SIZE) {
-		err("%s - exceeded ACL_BUFFER_SIZE", __FUNCTION__);
-		bluetooth->bulk_packet_pos = 0;
-		goto exit;
-	}
-
-	memcpy (&bluetooth->bulk_buffer[bluetooth->bulk_packet_pos],
-		urb->transfer_buffer, count);
-	bluetooth->bulk_packet_pos += count;
-	urb->actual_length = 0;
-
-	if (bluetooth->bulk_packet_pos >= ACL_HDR_SIZE) {
-		packet_size = CHAR2INT16(bluetooth->bulk_buffer[4],bluetooth->bulk_buffer[3]);
-	} else {
-		goto exit;
-	}
-
-	if (packet_size + ACL_HDR_SIZE < bluetooth->bulk_packet_pos) {
-		err("%s - packet was too long", __FUNCTION__);
-		bluetooth->bulk_packet_pos = 0;
-		goto exit;
-	}
-
-	if (packet_size + ACL_HDR_SIZE == bluetooth->bulk_packet_pos) {
-		for (i = 0; i < bluetooth->bulk_packet_pos; ++i) {
-			/* if we insert more than TTY_FLIPBUF_SIZE characters, we drop them. */
-			if (bluetooth->tty->flip.count >= TTY_FLIPBUF_SIZE) {
-				tty_flip_buffer_push(bluetooth->tty);
-			}
-			tty_insert_flip_char(bluetooth->tty, bluetooth->bulk_buffer[i], 0);
-		}
-		tty_flip_buffer_push(bluetooth->tty);
-		bluetooth->bulk_packet_pos = 0;
-	}	
-
-exit:
-	if (!bluetooth || !bluetooth->open_count)
-		return;
-
-	usb_fill_bulk_urb(bluetooth->read_urb, bluetooth->dev, 
-		      usb_rcvbulkpipe(bluetooth->dev, bluetooth->bulk_in_endpointAddress),
-		      bluetooth->bulk_in_buffer, bluetooth->bulk_in_buffer_size, 
-		      bluetooth_read_bulk_callback, bluetooth);
-	result = usb_submit_urb(bluetooth->read_urb, GFP_KERNEL);
-	if (result)
-		err ("%s - failed resubmitting read urb, error %d", __FUNCTION__, result);
-
-	return;
-}
-
-
-static void bluetooth_write_bulk_callback (struct urb *urb, struct pt_regs *regs)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)urb->context, __FUNCTION__);
-
-	dbg("%s", __FUNCTION__);
-
-	/* free up the transfer buffer, as usb_free_urb() does not do this */
-	kfree(urb->transfer_buffer);
-
-	if (!bluetooth) {
-		dbg("%s - bad bluetooth pointer, exiting", __FUNCTION__);
-		return;
-	}
-
-	if (urb->status) {
-		dbg("%s - nonzero write bulk status received: %d", __FUNCTION__, urb->status);
-		return;
-	}
-
-	/* wake up our little function to let the tty layer know that something happened */
-	schedule_work(&bluetooth->work);
-}
-
-
-static void bluetooth_softint(void *private)
-{
-	struct usb_bluetooth *bluetooth = get_usb_bluetooth ((struct usb_bluetooth *)private, __FUNCTION__);
-
-	dbg("%s", __FUNCTION__);
-
-	if (!bluetooth)
-		return;
-
-	tty_wakeup(bluetooth->tty);
-}
-
-
-static int usb_bluetooth_probe (struct usb_interface *intf, 
-				const struct usb_device_id *id)
-{
-	struct usb_device *dev = interface_to_usbdev (intf);
-	struct usb_bluetooth *bluetooth = NULL;
-	struct usb_host_interface *interface;
-	struct usb_endpoint_descriptor *endpoint;
-	struct usb_endpoint_descriptor *interrupt_in_endpoint[8];
-	struct usb_endpoint_descriptor *bulk_in_endpoint[8];
-	struct usb_endpoint_descriptor *bulk_out_endpoint[8];
-	int control_out_endpoint;
-
-	int minor;
-	int buffer_size;
-	int i;
-	int num_interrupt_in = 0;
-	int num_bulk_in = 0;
-	int num_bulk_out = 0;
-
-	interface = intf->cur_altsetting;
-	control_out_endpoint = interface->desc.bInterfaceNumber;
-
-	/* find the endpoints that we need */
-	for (i = 0; i < interface->desc.bNumEndpoints; ++i) {
-		endpoint = &interface->endpoint[i].desc;
-
-		if ((endpoint->bEndpointAddress & 0x80) &&
-		    ((endpoint->bmAttributes & 3) == 0x02)) {
-			/* we found a bulk in endpoint */
-			dbg("found bulk in");
-			bulk_in_endpoint[num_bulk_in] = endpoint;
-			++num_bulk_in;
-		}
-
-		if (((endpoint->bEndpointAddress & 0x80) == 0x00) &&
-		    ((endpoint->bmAttributes & 3) == 0x02)) {
-			/* we found a bulk out endpoint */
-			dbg("found bulk out");
-			bulk_out_endpoint[num_bulk_out] = endpoint;
-			++num_bulk_out;
-		}
-
-		if ((endpoint->bEndpointAddress & 0x80) &&
-		    ((endpoint->bmAttributes & 3) == 0x03)) {
-			/* we found a interrupt in endpoint */
-			dbg("found interrupt in");
-			interrupt_in_endpoint[num_interrupt_in] = endpoint;
-			++num_interrupt_in;
-		}
-	}
-
-	/* according to the spec, we can only have 1 bulk_in, 1 bulk_out, and 1 interrupt_in endpoints */
-	if ((num_bulk_in != 1) ||
-	    (num_bulk_out != 1) ||
-	    (num_interrupt_in != 1)) {
-		dbg ("%s - improper number of endpoints. Bluetooth driver not bound.", __FUNCTION__);
-		return -EIO;
-	}
-
-	info("USB Bluetooth converter detected");
-
-	for (minor = 0; minor < BLUETOOTH_TTY_MINORS && bluetooth_table[minor]; ++minor)
-		;
-	if (bluetooth_table[minor]) {
-		err("No more free Bluetooth devices");
-		return -ENODEV;
-	}
-
-	if (!(bluetooth = kmalloc(sizeof(struct usb_bluetooth), GFP_KERNEL))) {
-		err("Out of memory");
-		return -ENOMEM;
-	}
-
-	memset(bluetooth, 0, sizeof(struct usb_bluetooth));
-
-	bluetooth->magic = USB_BLUETOOTH_MAGIC;
-	bluetooth->dev = dev;
-	bluetooth->minor = minor;
-	INIT_WORK(&bluetooth->work, bluetooth_softint, bluetooth);
-	init_MUTEX(&bluetooth->lock);
-
-	/* record the interface number for the control out */
-	bluetooth->control_out_bInterfaceNum = control_out_endpoint;
-	
-	/* create our control out urb pool */ 
-	for (i = 0; i < NUM_CONTROL_URBS; ++i) {
-		struct urb  *urb = usb_alloc_urb(0, GFP_KERNEL);
-		if (urb == NULL) {
-			err("No free urbs available");
-			goto probe_error;
-		}
-		urb->transfer_buffer = NULL;
-		bluetooth->control_urb_pool[i] = urb;
-	}
-
-	/* set up the endpoint information */
-	endpoint = bulk_in_endpoint[0];
-	bluetooth->read_urb = usb_alloc_urb (0, GFP_KERNEL);
-	if (!bluetooth->read_urb) {
-		err("No free urbs available");
-		goto probe_error;
-	}
-	bluetooth->bulk_in_buffer_size = buffer_size = le16_to_cpu(endpoint->wMaxPacketSize);
-	bluetooth->bulk_in_endpointAddress = endpoint->bEndpointAddress;
-	bluetooth->bulk_in_buffer = kmalloc (buffer_size, GFP_KERNEL);
-	if (!bluetooth->bulk_in_buffer) {
-		err("Couldn't allocate bulk_in_buffer");
-		goto probe_error;
-	}
-	usb_fill_bulk_urb(bluetooth->read_urb, dev, usb_rcvbulkpipe(dev, endpoint->bEndpointAddress),
-		      bluetooth->bulk_in_buffer, buffer_size, bluetooth_read_bulk_callback, bluetooth);
-
-	endpoint = bulk_out_endpoint[0];
-	bluetooth->bulk_out_endpointAddress = endpoint->bEndpointAddress;
-	bluetooth->bulk_out_buffer_size = le16_to_cpu(endpoint->wMaxPacketSize) * 2;
-
-	endpoint = interrupt_in_endpoint[0];
-	bluetooth->interrupt_in_urb = usb_alloc_urb(0, GFP_KERNEL);
-	if (!bluetooth->interrupt_in_urb) {
-		err("No free urbs available");
-		goto probe_error;
-	}
-	bluetooth->interrupt_in_buffer_size = buffer_size = le16_to_cpu(endpoint->wMaxPacketSize);
-	bluetooth->interrupt_in_endpointAddress = endpoint->bEndpointAddress;
-	bluetooth->interrupt_in_interval = endpoint->bInterval;
-	bluetooth->interrupt_in_buffer = kmalloc (buffer_size, GFP_KERNEL);
-	if (!bluetooth->interrupt_in_buffer) {
-		err("Couldn't allocate interrupt_in_buffer");
-		goto probe_error;
-	}
-	usb_fill_int_urb(bluetooth->interrupt_in_urb, dev, usb_rcvintpipe(dev, endpoint->bEndpointAddress),
-		     bluetooth->interrupt_in_buffer, buffer_size, bluetooth_int_callback,
-		     bluetooth, endpoint->bInterval);
-
-	/* initialize the devfs nodes for this device and let the user know what bluetooths we are bound to */
-	tty_register_device (bluetooth_tty_driver, minor, &intf->dev);
-	info("Bluetooth converter now attached to ttyUB%d (or usb/ttub/%d for devfs)", minor, minor);
-
-	bluetooth_table[minor] = bluetooth;
-
-	/* success */
-	usb_set_intfdata (intf, bluetooth);
-	return 0;
-
-probe_error:
-	if (bluetooth->read_urb)
-		usb_free_urb (bluetooth->read_urb);
-	if (bluetooth->bulk_in_buffer)
-		kfree (bluetooth->bulk_in_buffer);
-	if (bluetooth->interrupt_in_urb)
-		usb_free_urb (bluetooth->interrupt_in_urb);
-	if (bluetooth->interrupt_in_buffer)
-		kfree (bluetooth->interrupt_in_buffer);
-	for (i = 0; i < NUM_CONTROL_URBS; ++i) 
-		if (bluetooth->control_urb_pool[i]) {
-			if (bluetooth->control_urb_pool[i]->transfer_buffer)
-				kfree (bluetooth->control_urb_pool[i]->transfer_buffer);
-			usb_free_urb (bluetooth->control_urb_pool[i]);
-		}
-
-	bluetooth_table[minor] = NULL;
-
-	/* free up any memory that we allocated */
-	kfree (bluetooth);
-	return -EIO;
-}
-
-
-static void usb_bluetooth_disconnect(struct usb_interface *intf)
-{
-	struct usb_bluetooth *bluetooth = usb_get_intfdata (intf);
-	int i;
-
-	usb_set_intfdata (intf, NULL);
-	if (bluetooth) {
-		if ((bluetooth->open_count) && (bluetooth->tty))
-			tty_hangup(bluetooth->tty);
-
-		bluetooth->open_count = 0;
-
-		if (bluetooth->read_urb) {
-			usb_kill_urb (bluetooth->read_urb);
-			usb_free_urb (bluetooth->read_urb);
-		}
-		if (bluetooth->bulk_in_buffer)
-			kfree (bluetooth->bulk_in_buffer);
-
-		if (bluetooth->interrupt_in_urb) {
-			usb_kill_urb (bluetooth->interrupt_in_urb);
-			usb_free_urb (bluetooth->interrupt_in_urb);
-		}
-		if (bluetooth->interrupt_in_buffer)
-			kfree (bluetooth->interrupt_in_buffer);
-
-		tty_unregister_device (bluetooth_tty_driver, bluetooth->minor);
-
-		for (i = 0; i < NUM_CONTROL_URBS; ++i) {
-			if (bluetooth->control_urb_pool[i]) {
-				usb_kill_urb (bluetooth->control_urb_pool[i]);
-				if (bluetooth->control_urb_pool[i]->transfer_buffer)
-					kfree (bluetooth->control_urb_pool[i]->transfer_buffer);
-				usb_free_urb (bluetooth->control_urb_pool[i]);
-			}
-		}
-		
-		info("Bluetooth converter now disconnected from ttyUB%d", bluetooth->minor);
-
-		bluetooth_table[bluetooth->minor] = NULL;
-
-		/* free up any memory that we allocated */
-		kfree (bluetooth);
-	} else {
-		info("device disconnected");
-	}
-}
-
-static struct tty_operations bluetooth_ops = {
-	.open =			bluetooth_open,
-	.close =		bluetooth_close,
-	.write =		bluetooth_write,
-	.write_room =		bluetooth_write_room,
-	.ioctl =		bluetooth_ioctl,
-	.set_termios =		bluetooth_set_termios,
-	.throttle =		bluetooth_throttle,
-	.unthrottle =		bluetooth_unthrottle,
-	.chars_in_buffer =	bluetooth_chars_in_buffer,
-};
-
-static int usb_bluetooth_init(void)
-{
-	int i;
-	int result;
-
-	/* Initialize our global data */
-	for (i = 0; i < BLUETOOTH_TTY_MINORS; ++i) {
-		bluetooth_table[i] = NULL;
-	}
-
-	info ("USB Bluetooth support registered");
-
-	bluetooth_tty_driver = alloc_tty_driver(BLUETOOTH_TTY_MINORS);
-	if (!bluetooth_tty_driver)
-		return -ENOMEM;
-
-	bluetooth_tty_driver->owner = THIS_MODULE;
-	bluetooth_tty_driver->driver_name = "usb-bluetooth";
-	bluetooth_tty_driver->name = "ttyUB";
-	bluetooth_tty_driver->devfs_name = "usb/ttub/";
-	bluetooth_tty_driver->major = BLUETOOTH_TTY_MAJOR;
-	bluetooth_tty_driver->minor_start = 0;
-	bluetooth_tty_driver->type = TTY_DRIVER_TYPE_SERIAL;
-	bluetooth_tty_driver->subtype = SERIAL_TYPE_NORMAL;
-	bluetooth_tty_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_NO_DEVFS;
-	bluetooth_tty_driver->init_termios = tty_std_termios;
-	bluetooth_tty_driver->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL;
-	tty_set_operations(bluetooth_tty_driver, &bluetooth_ops);
-	if (tty_register_driver (bluetooth_tty_driver)) {
-		err("%s - failed to register tty driver", __FUNCTION__);
-		put_tty_driver(bluetooth_tty_driver);
-		return -1;
-	}
-
-	/* register the USB driver */
-	result = usb_register(&usb_bluetooth_driver);
-	if (result < 0) {
-		tty_unregister_driver(bluetooth_tty_driver);
-		put_tty_driver(bluetooth_tty_driver);
-		err("usb_register failed for the USB bluetooth driver. Error number %d", result);
-		return -1;
-	}
-
-	info(DRIVER_DESC " " DRIVER_VERSION);
-
-	return 0;
-}
-
-
-static void usb_bluetooth_exit(void)
-{
-	usb_deregister(&usb_bluetooth_driver);
-	tty_unregister_driver(bluetooth_tty_driver);
-	put_tty_driver(bluetooth_tty_driver);
-}
-
-
-module_init(usb_bluetooth_init);
-module_exit(usb_bluetooth_exit);
-
-/* Module information */
-MODULE_AUTHOR( DRIVER_AUTHOR );
-MODULE_DESCRIPTION( DRIVER_DESC );
-MODULE_LICENSE("GPL");
-
-- 
cgit v1.1


From ea65370d025f5005649e5cb37c4d025e92c6fc38 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB Serial: rename usb_serial_device_type to
 usb_serial_driver

I'm tired of trying to explain why a "device_type" is really a driver.
This better describes exactly what this structure is.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/airprime.c         |  2 +-
 drivers/usb/serial/belkin_sa.c        |  2 +-
 drivers/usb/serial/bus.c              | 28 ++++++++++++++--------------
 drivers/usb/serial/cp2101.c           |  2 +-
 drivers/usb/serial/cyberjack.c        |  2 +-
 drivers/usb/serial/cypress_m8.c       |  4 ++--
 drivers/usb/serial/digi_acceleport.c  |  4 ++--
 drivers/usb/serial/empeg.c            |  2 +-
 drivers/usb/serial/ftdi_sio.c         |  2 +-
 drivers/usb/serial/garmin_gps.c       |  7 +------
 drivers/usb/serial/generic.c          |  2 +-
 drivers/usb/serial/hp4x.c             |  2 +-
 drivers/usb/serial/io_tables.h        |  6 +++---
 drivers/usb/serial/io_ti.c            |  4 ++--
 drivers/usb/serial/ipaq.c             |  2 +-
 drivers/usb/serial/ipw.c              |  2 +-
 drivers/usb/serial/ir-usb.c           |  2 +-
 drivers/usb/serial/keyspan.h          |  8 ++++----
 drivers/usb/serial/keyspan_pda.c      |  6 +++---
 drivers/usb/serial/kl5kusb105.c       |  2 +-
 drivers/usb/serial/kobil_sct.c        |  2 +-
 drivers/usb/serial/mct_u232.c         |  2 +-
 drivers/usb/serial/omninet.c          |  2 +-
 drivers/usb/serial/option.c           |  2 +-
 drivers/usb/serial/pl2303.c           |  2 +-
 drivers/usb/serial/safe_serial.c      |  2 +-
 drivers/usb/serial/ti_usb_3410_5052.c |  4 ++--
 drivers/usb/serial/usb-serial.c       | 30 +++++++++++++++---------------
 drivers/usb/serial/usb-serial.h       | 28 ++++++++++++++--------------
 drivers/usb/serial/visor.c            |  6 +++---
 drivers/usb/serial/whiteheat.c        |  4 ++--
 31 files changed, 85 insertions(+), 90 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/serial/airprime.c b/drivers/usb/serial/airprime.c
index 926d4c2..104c043 100644
--- a/drivers/usb/serial/airprime.c
+++ b/drivers/usb/serial/airprime.c
@@ -30,7 +30,7 @@ static struct usb_driver airprime_driver = {
 	.id_table =	id_table,
 };
 
-static struct usb_serial_device_type airprime_device = {
+static struct usb_serial_driver airprime_device = {
 	.owner =		THIS_MODULE,
 	.name =			"airprime",
 	.id_table =		id_table,
diff --git a/drivers/usb/serial/belkin_sa.c b/drivers/usb/serial/belkin_sa.c
index abb1b2c..6d84de4 100644
--- a/drivers/usb/serial/belkin_sa.c
+++ b/drivers/usb/serial/belkin_sa.c
@@ -121,7 +121,7 @@ static struct usb_driver belkin_driver = {
 };
 
 /* All of the device info needed for the serial converters */
-static struct usb_serial_device_type belkin_device = {
+static struct usb_serial_driver belkin_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Belkin / Peracom / GoHubs USB Serial Adapter",
 	.short_name =		"belkin",
diff --git a/drivers/usb/serial/bus.c b/drivers/usb/serial/bus.c
index 2f612c2..5a0bcd3 100644
--- a/drivers/usb/serial/bus.c
+++ b/drivers/usb/serial/bus.c
@@ -18,7 +18,7 @@
 
 static int usb_serial_device_match (struct device *dev, struct device_driver *drv)
 {
-	struct usb_serial_device_type *driver;
+	struct usb_serial_driver *driver;
 	const struct usb_serial_port *port;
 
 	/*
@@ -44,7 +44,7 @@ struct bus_type usb_serial_bus_type = {
 
 static int usb_serial_device_probe (struct device *dev)
 {
-	struct usb_serial_device_type *driver;
+	struct usb_serial_driver *driver;
 	struct usb_serial_port *port;
 	int retval = 0;
 	int minor;
@@ -80,7 +80,7 @@ exit:
 
 static int usb_serial_device_remove (struct device *dev)
 {
-	struct usb_serial_device_type *driver;
+	struct usb_serial_driver *driver;
 	struct usb_serial_port *port;
 	int retval = 0;
 	int minor;
@@ -109,26 +109,26 @@ exit:
 	return retval;
 }
 
-int usb_serial_bus_register(struct usb_serial_device_type *device)
+int usb_serial_bus_register(struct usb_serial_driver *driver)
 {
 	int retval;
 
-	if (device->short_name)
-		device->driver.name = (char *)device->short_name;
+	if (driver->short_name)
+		driver->driver.name = (char *)driver->short_name;
 	else
-		device->driver.name = (char *)device->name;
-	device->driver.bus = &usb_serial_bus_type;
-	device->driver.probe = usb_serial_device_probe;
-	device->driver.remove = usb_serial_device_remove;
-	device->driver.owner = device->owner;
+		driver->driver.name = (char *)driver->name;
+	driver->driver.bus = &usb_serial_bus_type;
+	driver->driver.probe = usb_serial_device_probe;
+	driver->driver.remove = usb_serial_device_remove;
+	driver->driver.owner = driver->owner;
 
-	retval = driver_register(&device->driver);
+	retval = driver_register(&driver->driver);
 
 	return retval;
 }
 
-void usb_serial_bus_deregister(struct usb_serial_device_type *device)
+void usb_serial_bus_deregister(struct usb_serial_driver *driver)
 {
-	driver_unregister (&device->driver);
+	driver_unregister(&driver->driver);
 }
 
diff --git a/drivers/usb/serial/cp2101.c b/drivers/usb/serial/cp2101.c
index 97c78c2..0b45b58 100644
--- a/drivers/usb/serial/cp2101.c
+++ b/drivers/usb/serial/cp2101.c
@@ -73,7 +73,7 @@ static struct usb_driver cp2101_driver = {
 	.id_table	= id_table,
 };
 
-static struct usb_serial_device_type cp2101_device = {
+static struct usb_serial_driver cp2101_device = {
 	.owner			= THIS_MODULE,
 	.name			= "CP2101",
 	.id_table		= id_table,
diff --git a/drivers/usb/serial/cyberjack.c b/drivers/usb/serial/cyberjack.c
index b5b4310..9f421a3 100644
--- a/drivers/usb/serial/cyberjack.c
+++ b/drivers/usb/serial/cyberjack.c
@@ -83,7 +83,7 @@ static struct usb_driver cyberjack_driver = {
 	.id_table =	id_table,
 };
 
-static struct usb_serial_device_type cyberjack_device = {
+static struct usb_serial_driver cyberjack_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Reiner SCT Cyberjack USB card reader",
 	.short_name =		"cyberjack",
diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c
index 9ee1aaf..4fb8e59 100644
--- a/drivers/usb/serial/cypress_m8.c
+++ b/drivers/usb/serial/cypress_m8.c
@@ -176,7 +176,7 @@ static unsigned int	  cypress_buf_put(struct cypress_buf *cb, const char *buf, u
 static unsigned int	  cypress_buf_get(struct cypress_buf *cb, char *buf, unsigned int count);
 
 
-static struct usb_serial_device_type cypress_earthmate_device = {
+static struct usb_serial_driver cypress_earthmate_device = {
 	.owner =			THIS_MODULE,
 	.name =				"DeLorme Earthmate USB",
 	.short_name =			"earthmate",
@@ -203,7 +203,7 @@ static struct usb_serial_device_type cypress_earthmate_device = {
 	.write_int_callback =		cypress_write_int_callback,
 };
 
-static struct usb_serial_device_type cypress_hidcom_device = {
+static struct usb_serial_driver cypress_hidcom_device = {
 	.owner =			THIS_MODULE,
 	.name =				"HID->COM RS232 Adapter",
 	.short_name =			"cyphidcom",
diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c
index a19a47f..66feb88 100644
--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -503,7 +503,7 @@ static struct usb_driver digi_driver = {
 
 /* device info needed for the Digi serial converter */
 
-static struct usb_serial_device_type digi_acceleport_2_device = {
+static struct usb_serial_driver digi_acceleport_2_device = {
 	.owner =			THIS_MODULE,
 	.name =				"Digi 2 port USB adapter",
 	.short_name =			"digi_2",
@@ -530,7 +530,7 @@ static struct usb_serial_device_type digi_acceleport_2_device = {
 	.shutdown =			digi_shutdown,
 };
 
-static struct usb_serial_device_type digi_acceleport_4_device = {
+static struct usb_serial_driver digi_acceleport_4_device = {
 	.owner =			THIS_MODULE,
 	.name =				"Digi 4 port USB adapter",
 	.short_name =			"digi_4",
diff --git a/drivers/usb/serial/empeg.c b/drivers/usb/serial/empeg.c
index 8d562ab..cbea8b3 100644
--- a/drivers/usb/serial/empeg.c
+++ b/drivers/usb/serial/empeg.c
@@ -112,7 +112,7 @@ static struct usb_driver empeg_driver = {
 	.id_table =	id_table,
 };
 
-static struct usb_serial_device_type empeg_device = {
+static struct usb_serial_driver empeg_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Empeg",
 	.id_table =		id_table,
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index b713113..529e1a7 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -562,7 +562,7 @@ static unsigned short int ftdi_232am_baud_to_divisor (int baud);
 static __u32 ftdi_232bm_baud_base_to_divisor (int baud, int base);
 static __u32 ftdi_232bm_baud_to_divisor (int baud);
 
-static struct usb_serial_device_type ftdi_sio_device = {
+static struct usb_serial_driver ftdi_sio_device = {
 	.owner =		THIS_MODULE,
 	.name =			"FTDI USB Serial Device",
 	.short_name =		"ftdi_sio",
diff --git a/drivers/usb/serial/garmin_gps.c b/drivers/usb/serial/garmin_gps.c
index 2ef614d..7361194 100644
--- a/drivers/usb/serial/garmin_gps.c
+++ b/drivers/usb/serial/garmin_gps.c
@@ -1468,13 +1468,8 @@ static void garmin_shutdown (struct usb_serial *serial)
 }
 
 
-
-
-
-
-
 /* All of the device info needed */
-static struct usb_serial_device_type garmin_device = {
+static struct usb_serial_driver garmin_device = {
 	.owner               = THIS_MODULE,
 	.name                = "Garmin GPS usb/tty",
 	.short_name          = "garmin_gps",
diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c
index 5f7d319..7f567bf 100644
--- a/drivers/usb/serial/generic.c
+++ b/drivers/usb/serial/generic.c
@@ -36,7 +36,7 @@ MODULE_PARM_DESC(product, "User specified USB idProduct");
 static struct usb_device_id generic_device_ids[2]; /* Initially all zeroes. */
 
 /* All of the device info needed for the Generic Serial Converter */
-struct usb_serial_device_type usb_serial_generic_device = {
+struct usb_serial_driver usb_serial_generic_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Generic",
 	.short_name =		"generic",
diff --git a/drivers/usb/serial/hp4x.c b/drivers/usb/serial/hp4x.c
index 64d55fb..b494699 100644
--- a/drivers/usb/serial/hp4x.c
+++ b/drivers/usb/serial/hp4x.c
@@ -44,7 +44,7 @@ static struct usb_driver hp49gp_driver = {
 	.id_table =	id_table,
 };
 
-static struct usb_serial_device_type hp49gp_device = {
+static struct usb_serial_driver hp49gp_device = {
 	.owner =		THIS_MODULE,
 	.name =			"HP4X",
 	.id_table =		id_table,
diff --git a/drivers/usb/serial/io_tables.h b/drivers/usb/serial/io_tables.h
index e7ffe02..7314c04 100644
--- a/drivers/usb/serial/io_tables.h
+++ b/drivers/usb/serial/io_tables.h
@@ -75,7 +75,7 @@ static struct usb_device_id id_table_combined [] = {
 
 MODULE_DEVICE_TABLE (usb, id_table_combined);
 
-static struct usb_serial_device_type edgeport_2port_device = {
+static struct usb_serial_driver edgeport_2port_device = {
 	.owner			= THIS_MODULE,
 	.name			= "Edgeport 2 port adapter",
 	.short_name		= "edgeport_2",
@@ -103,7 +103,7 @@ static struct usb_serial_device_type edgeport_2port_device = {
 	.write_bulk_callback	= edge_bulk_out_data_callback,
 };
 
-static struct usb_serial_device_type edgeport_4port_device = {
+static struct usb_serial_driver edgeport_4port_device = {
 	.owner			= THIS_MODULE,
 	.name			= "Edgeport 4 port adapter",
 	.short_name		= "edgeport_4",
@@ -131,7 +131,7 @@ static struct usb_serial_device_type edgeport_4port_device = {
 	.write_bulk_callback	= edge_bulk_out_data_callback,
 };
 
-static struct usb_serial_device_type edgeport_8port_device = {
+static struct usb_serial_driver edgeport_8port_device = {
 	.owner			= THIS_MODULE,
 	.name			= "Edgeport 8 port adapter",
 	.short_name		= "edgeport_8",
diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c
index ebf9967..4328cc7 100644
--- a/drivers/usb/serial/io_ti.c
+++ b/drivers/usb/serial/io_ti.c
@@ -2982,7 +2982,7 @@ static unsigned int edge_buf_get(struct edge_buf *eb, char *buf,
 }
 
 
-static struct usb_serial_device_type edgeport_1port_device = {
+static struct usb_serial_driver edgeport_1port_device = {
 	.owner			= THIS_MODULE,
 	.name			= "Edgeport TI 1 port adapter",
 	.short_name		= "edgeport_ti_1",
@@ -3010,7 +3010,7 @@ static struct usb_serial_device_type edgeport_1port_device = {
 	.write_bulk_callback	= edge_bulk_out_callback,
 };
 
-static struct usb_serial_device_type edgeport_2port_device = {
+static struct usb_serial_driver edgeport_2port_device = {
 	.owner			= THIS_MODULE,
 	.name			= "Edgeport TI 2 port adapter",
 	.short_name		= "edgeport_ti_2",
diff --git a/drivers/usb/serial/ipaq.c b/drivers/usb/serial/ipaq.c
index c05c2a2..9a79ad8 100644
--- a/drivers/usb/serial/ipaq.c
+++ b/drivers/usb/serial/ipaq.c
@@ -547,7 +547,7 @@ static struct usb_driver ipaq_driver = {
 
 
 /* All of the device info needed for the Compaq iPAQ */
-static struct usb_serial_device_type ipaq_device = {
+static struct usb_serial_driver ipaq_device = {
 	.owner =		THIS_MODULE,
 	.name =			"PocketPC PDA",
 	.id_table =		ipaq_id_table,
diff --git a/drivers/usb/serial/ipw.c b/drivers/usb/serial/ipw.c
index 85e2424..04524d3 100644
--- a/drivers/usb/serial/ipw.c
+++ b/drivers/usb/serial/ipw.c
@@ -443,7 +443,7 @@ static int ipw_disconnect(struct usb_serial_port *port)
 	return 0;
 }
 
-static struct usb_serial_device_type ipw_device = {
+static struct usb_serial_driver ipw_device = {
 	.owner =		THIS_MODULE,
 	.name =			"IPWireless converter",
 	.short_name =		"ipw",
diff --git a/drivers/usb/serial/ir-usb.c b/drivers/usb/serial/ir-usb.c
index 937b2fd..ecfb206 100644
--- a/drivers/usb/serial/ir-usb.c
+++ b/drivers/usb/serial/ir-usb.c
@@ -133,7 +133,7 @@ static struct usb_driver ir_driver = {
 };
 
 
-static struct usb_serial_device_type ir_device = {
+static struct usb_serial_driver ir_device = {
 	.owner =		THIS_MODULE,
 	.name =			"IR Dongle",
 	.id_table =		id_table,
diff --git a/drivers/usb/serial/keyspan.h b/drivers/usb/serial/keyspan.h
index e9b45b7..97e7d9e 100644
--- a/drivers/usb/serial/keyspan.h
+++ b/drivers/usb/serial/keyspan.h
@@ -570,7 +570,7 @@ static struct usb_device_id keyspan_4port_ids[] = {
 };
 
 /* Structs for the devices, pre and post renumeration. */
-static struct usb_serial_device_type keyspan_pre_device = {
+static struct usb_serial_driver keyspan_pre_device = {
 	.owner			= THIS_MODULE,
 	.name			= "Keyspan - (without firmware)",
 	.short_name		= "keyspan_no_firm",
@@ -582,7 +582,7 @@ static struct usb_serial_device_type keyspan_pre_device = {
 	.attach			= keyspan_fake_startup,
 };
 
-static struct usb_serial_device_type keyspan_1port_device = {
+static struct usb_serial_driver keyspan_1port_device = {
 	.owner			= THIS_MODULE,
 	.name			= "Keyspan 1 port adapter",
 	.short_name		= "keyspan_1",
@@ -607,7 +607,7 @@ static struct usb_serial_device_type keyspan_1port_device = {
 	.shutdown		= keyspan_shutdown,
 };
 
-static struct usb_serial_device_type keyspan_2port_device = {
+static struct usb_serial_driver keyspan_2port_device = {
 	.owner			= THIS_MODULE,
 	.name			= "Keyspan 2 port adapter",
 	.short_name		= "keyspan_2",
@@ -632,7 +632,7 @@ static struct usb_serial_device_type keyspan_2port_device = {
 	.shutdown		= keyspan_shutdown,
 };
 
-static struct usb_serial_device_type keyspan_4port_device = {
+static struct usb_serial_driver keyspan_4port_device = {
 	.owner			= THIS_MODULE,
 	.name			= "Keyspan 4 port adapter",
 	.short_name		= "keyspan_4",
diff --git a/drivers/usb/serial/keyspan_pda.c b/drivers/usb/serial/keyspan_pda.c
index 635c384..8fad0e9 100644
--- a/drivers/usb/serial/keyspan_pda.c
+++ b/drivers/usb/serial/keyspan_pda.c
@@ -783,7 +783,7 @@ static void keyspan_pda_shutdown (struct usb_serial *serial)
 }
 
 #ifdef KEYSPAN
-static struct usb_serial_device_type keyspan_pda_fake_device = {
+static struct usb_serial_driver keyspan_pda_fake_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Keyspan PDA - (prerenumeration)",
 	.short_name =		"keyspan_pda_pre",
@@ -797,7 +797,7 @@ static struct usb_serial_device_type keyspan_pda_fake_device = {
 #endif
 
 #ifdef XIRCOM
-static struct usb_serial_device_type xircom_pgs_fake_device = {
+static struct usb_serial_driver xircom_pgs_fake_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Xircom / Entregra PGS - (prerenumeration)",
 	.short_name =		"xircom_no_firm",
@@ -810,7 +810,7 @@ static struct usb_serial_device_type xircom_pgs_fake_device = {
 };
 #endif
 
-static struct usb_serial_device_type keyspan_pda_device = {
+static struct usb_serial_driver keyspan_pda_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Keyspan PDA",
 	.short_name =		"keyspan_pda",
diff --git a/drivers/usb/serial/kl5kusb105.c b/drivers/usb/serial/kl5kusb105.c
index a11e829..be08270 100644
--- a/drivers/usb/serial/kl5kusb105.c
+++ b/drivers/usb/serial/kl5kusb105.c
@@ -123,7 +123,7 @@ static struct usb_driver kl5kusb105d_driver = {
 	.id_table =	id_table,
 };
 
-static struct usb_serial_device_type kl5kusb105d_device = {
+static struct usb_serial_driver kl5kusb105d_device = {
 	.owner =             THIS_MODULE,
 	.name =		     "KL5KUSB105D / PalmConnect",
 	.short_name =	     "kl5kusb105d",
diff --git a/drivers/usb/serial/kobil_sct.c b/drivers/usb/serial/kobil_sct.c
index fe4c98a..9494434 100644
--- a/drivers/usb/serial/kobil_sct.c
+++ b/drivers/usb/serial/kobil_sct.c
@@ -105,7 +105,7 @@ static struct usb_driver kobil_driver = {
 };
 
 
-static struct usb_serial_device_type kobil_device = {
+static struct usb_serial_driver kobil_device = {
 	.owner =		THIS_MODULE,
 	.name =			"KOBIL USB smart card terminal",
 	.id_table =		id_table,
diff --git a/drivers/usb/serial/mct_u232.c b/drivers/usb/serial/mct_u232.c
index 50b63696..94709643 100644
--- a/drivers/usb/serial/mct_u232.c
+++ b/drivers/usb/serial/mct_u232.c
@@ -132,7 +132,7 @@ static struct usb_driver mct_u232_driver = {
 	.id_table =	id_table_combined,
 };
 
-static struct usb_serial_device_type mct_u232_device = {
+static struct usb_serial_driver mct_u232_device = {
 	.owner =	     THIS_MODULE,
 	.name =		     "MCT U232",
 	.short_name =	     "mct_u232",
diff --git a/drivers/usb/serial/omninet.c b/drivers/usb/serial/omninet.c
index 6a99ae1..53c0588 100644
--- a/drivers/usb/serial/omninet.c
+++ b/drivers/usb/serial/omninet.c
@@ -88,7 +88,7 @@ static struct usb_driver omninet_driver = {
 };
 
 
-static struct usb_serial_device_type zyxel_omninet_device = {
+static struct usb_serial_driver zyxel_omninet_device = {
 	.owner =		THIS_MODULE,
 	.name =			"ZyXEL - omni.net lcd plus usb",
 	.short_name =		"omninet",
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 4989e57..6ec9266 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -105,7 +105,7 @@ static struct usb_driver option_driver = {
 /* The card has three separate interfaces, wich the serial driver
  * recognizes separately, thus num_port=1.
  */
-static struct usb_serial_device_type option_3port_device = {
+static struct usb_serial_driver option_3port_device = {
 	.owner             = THIS_MODULE,
 	.name              = "Option 3G data card",
 	.short_name        = "option",
diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index 3cf245b..7134648 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -175,7 +175,7 @@ static unsigned int pl2303_buf_get(struct pl2303_buf *pb, char *buf,
 
 
 /* All of the device info needed for the PL2303 SIO serial converter */
-static struct usb_serial_device_type pl2303_device = {
+static struct usb_serial_driver pl2303_device = {
 	.owner =		THIS_MODULE,
 	.name =			"PL-2303",
 	.id_table =		id_table,
diff --git a/drivers/usb/serial/safe_serial.c b/drivers/usb/serial/safe_serial.c
index 88bf14a..87871bb 100644
--- a/drivers/usb/serial/safe_serial.c
+++ b/drivers/usb/serial/safe_serial.c
@@ -397,7 +397,7 @@ static int safe_startup (struct usb_serial *serial)
 	return 0;
 }
 
-static struct usb_serial_device_type safe_device = {
+static struct usb_serial_driver safe_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Safe",
 	.id_table =		id_table,
diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index 59c88de..f2efaf6 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -255,7 +255,7 @@ static struct usb_driver ti_usb_driver = {
 	.id_table		= ti_id_table_combined,
 };
 
-static struct usb_serial_device_type ti_1port_device = {
+static struct usb_serial_driver ti_1port_device = {
 	.owner			= THIS_MODULE,
 	.name			= "TI USB 3410 1 port adapter",
 	.id_table		= ti_id_table_3410,
@@ -282,7 +282,7 @@ static struct usb_serial_device_type ti_1port_device = {
 	.write_bulk_callback	= ti_bulk_out_callback,
 };
 
-static struct usb_serial_device_type ti_2port_device = {
+static struct usb_serial_driver ti_2port_device = {
 	.owner			= THIS_MODULE,
 	.name			= "TI USB 5052 2 port adapter",
 	.id_table		= ti_id_table_5052,
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index e77fbdf..cf083da 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -823,7 +823,7 @@ static void port_release(struct device *dev)
 
 static struct usb_serial * create_serial (struct usb_device *dev, 
 					  struct usb_interface *interface,
-					  struct usb_serial_device_type *type)
+					  struct usb_serial_driver *driver)
 {
 	struct usb_serial *serial;
 
@@ -834,22 +834,22 @@ static struct usb_serial * create_serial (struct usb_device *dev,
 	}
 	memset (serial, 0, sizeof(*serial));
 	serial->dev = usb_get_dev(dev);
-	serial->type = type;
+	serial->type = driver;
 	serial->interface = interface;
 	kref_init(&serial->kref);
 
 	return serial;
 }
 
-static struct usb_serial_device_type *search_serial_device(struct usb_interface *iface)
+static struct usb_serial_driver *search_serial_device(struct usb_interface *iface)
 {
 	struct list_head *p;
 	const struct usb_device_id *id;
-	struct usb_serial_device_type *t;
+	struct usb_serial_driver *t;
 
 	/* List trough know devices and see if the usb id matches */
 	list_for_each(p, &usb_serial_driver_list) {
-		t = list_entry(p, struct usb_serial_device_type, driver_list);
+		t = list_entry(p, struct usb_serial_driver, driver_list);
 		id = usb_match_id(iface, t->id_table);
 		if (id != NULL) {
 			dbg("descriptor matches");
@@ -872,7 +872,7 @@ int usb_serial_probe(struct usb_interface *interface,
 	struct usb_endpoint_descriptor *interrupt_out_endpoint[MAX_NUM_PORTS];
 	struct usb_endpoint_descriptor *bulk_in_endpoint[MAX_NUM_PORTS];
 	struct usb_endpoint_descriptor *bulk_out_endpoint[MAX_NUM_PORTS];
-	struct usb_serial_device_type *type = NULL;
+	struct usb_serial_driver *type = NULL;
 	int retval;
 	int minor;
 	int buffer_size;
@@ -1375,7 +1375,7 @@ module_exit(usb_serial_exit);
 			}						\
 	} while (0)
 
-static void fixup_generic(struct usb_serial_device_type *device)
+static void fixup_generic(struct usb_serial_driver *device)
 {
 	set_to_generic_if_null(device, open);
 	set_to_generic_if_null(device, write);
@@ -1387,28 +1387,28 @@ static void fixup_generic(struct usb_serial_device_type *device)
 	set_to_generic_if_null(device, shutdown);
 }
 
-int usb_serial_register(struct usb_serial_device_type *new_device)
+int usb_serial_register(struct usb_serial_driver *driver)
 {
 	int retval;
 
-	fixup_generic(new_device);
+	fixup_generic(driver);
 
 	/* Add this device to our list of devices */
-	list_add(&new_device->driver_list, &usb_serial_driver_list);
+	list_add(&driver->driver_list, &usb_serial_driver_list);
 
-	retval = usb_serial_bus_register(new_device);
+	retval = usb_serial_bus_register(driver);
 	if (retval) {
-		err("problem %d when registering driver %s", retval, new_device->name);
-		list_del(&new_device->driver_list);
+		err("problem %d when registering driver %s", retval, driver->name);
+		list_del(&driver->driver_list);
 	}
 	else
-		info("USB Serial support registered for %s", new_device->name);
+		info("USB Serial support registered for %s", driver->name);
 
 	return retval;
 }
 
 
-void usb_serial_deregister(struct usb_serial_device_type *device)
+void usb_serial_deregister(struct usb_serial_driver *device)
 {
 	info("USB Serial deregistering driver %s", device->name);
 	list_del(&device->driver_list);
diff --git a/drivers/usb/serial/usb-serial.h b/drivers/usb/serial/usb-serial.h
index 57f92f0..d6738b1 100644
--- a/drivers/usb/serial/usb-serial.h
+++ b/drivers/usb/serial/usb-serial.h
@@ -143,7 +143,7 @@ static inline void usb_set_serial_port_data (struct usb_serial_port *port, void
 /**
  * usb_serial - structure used by the usb-serial core for a device
  * @dev: pointer to the struct usb_device for this device
- * @type: pointer to the struct usb_serial_device_type for this device
+ * @type: pointer to the struct usb_serial_driver for this device
  * @interface: pointer to the struct usb_interface for this device
  * @minor: the starting minor number for this device
  * @num_ports: the number of ports this device has
@@ -159,7 +159,7 @@ static inline void usb_set_serial_port_data (struct usb_serial_port *port, void
  */
 struct usb_serial {
 	struct usb_device *		dev;
-	struct usb_serial_device_type *	type;
+	struct usb_serial_driver *	type;
 	struct usb_interface *		interface;
 	unsigned char			minor;
 	unsigned char			num_ports;
@@ -188,11 +188,11 @@ static inline void usb_set_serial_data (struct usb_serial *serial, void *data)
 }
 
 /**
- * usb_serial_device_type - a structure that defines a usb serial device
- * @owner: pointer to the module that owns this device.
- * @name: pointer to a string that describes this device.  This string used
+ * usb_serial_driver - describes a usb serial driver
+ * @owner: pointer to the module that owns this driver.
+ * @name: pointer to a string that describes this driver.  This string used
  *	in the syslog messages when a device is inserted or removed.
- * @short_name: a pointer to a string that describes this device in
+ * @short_name: a pointer to a string that describes this driver in
  *	KOBJ_NAME_LEN characters or less.  This is used for the sysfs interface
  *	to describe the driver.
  * @id_table: pointer to a list of usb_device_id structures that define all
@@ -221,13 +221,13 @@ static inline void usb_set_serial_data (struct usb_serial *serial, void *data)
  * @shutdown: pointer to the driver's shutdown function.  This will be
  *	called when the device is removed from the system.
  *
- * This structure is defines a USB Serial device.  It provides all of
+ * This structure is defines a USB Serial driver.  It provides all of
  * the information that the USB serial core code needs.  If the function
  * pointers are defined, then the USB serial core code will call them when
  * the corresponding tty port functions are called.  If they are not
  * called, the generic serial function will be used instead.
  */
-struct usb_serial_device_type {
+struct usb_serial_driver {
 	struct module *owner;
 	char	*name;
 	char	*short_name;
@@ -269,10 +269,10 @@ struct usb_serial_device_type {
 	void (*read_bulk_callback)(struct urb *urb, struct pt_regs *regs);
 	void (*write_bulk_callback)(struct urb *urb, struct pt_regs *regs);
 };
-#define to_usb_serial_driver(d) container_of(d, struct usb_serial_device_type, driver)
+#define to_usb_serial_driver(d) container_of(d, struct usb_serial_driver, driver)
 
-extern int  usb_serial_register(struct usb_serial_device_type *new_device);
-extern void usb_serial_deregister(struct usb_serial_device_type *device);
+extern int  usb_serial_register(struct usb_serial_driver *driver);
+extern void usb_serial_deregister(struct usb_serial_driver *driver);
 extern void usb_serial_port_softint(void *private);
 
 extern int usb_serial_probe(struct usb_interface *iface, const struct usb_device_id *id);
@@ -303,10 +303,10 @@ extern void usb_serial_generic_shutdown (struct usb_serial *serial);
 extern int usb_serial_generic_register (int debug);
 extern void usb_serial_generic_deregister (void);
 
-extern int usb_serial_bus_register (struct usb_serial_device_type *device);
-extern void usb_serial_bus_deregister (struct usb_serial_device_type *device);
+extern int usb_serial_bus_register (struct usb_serial_driver *device);
+extern void usb_serial_bus_deregister (struct usb_serial_driver *device);
 
-extern struct usb_serial_device_type usb_serial_generic_device;
+extern struct usb_serial_driver usb_serial_generic_device;
 extern struct bus_type usb_serial_bus_type;
 extern struct tty_driver *usb_serial_tty_driver;
 
diff --git a/drivers/usb/serial/visor.c b/drivers/usb/serial/visor.c
index 31c57ad..825451b 100644
--- a/drivers/usb/serial/visor.c
+++ b/drivers/usb/serial/visor.c
@@ -311,7 +311,7 @@ static struct usb_driver visor_driver = {
 };
 
 /* All of the device info needed for the Handspring Visor, and Palm 4.0 devices */
-static struct usb_serial_device_type handspring_device = {
+static struct usb_serial_driver handspring_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Handspring Visor / Palm OS",
 	.short_name =		"visor",
@@ -339,7 +339,7 @@ static struct usb_serial_device_type handspring_device = {
 };
 
 /* All of the device info needed for the Clie UX50, TH55 Palm 5.0 devices */
-static struct usb_serial_device_type clie_5_device = {
+static struct usb_serial_driver clie_5_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Sony Clie 5.0",
 	.short_name =		"clie_5",
@@ -367,7 +367,7 @@ static struct usb_serial_device_type clie_5_device = {
 };
 
 /* device info for the Sony Clie OS version 3.5 */
-static struct usb_serial_device_type clie_3_5_device = {
+static struct usb_serial_driver clie_3_5_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Sony Clie 3.5",
 	.short_name =		"clie_3.5",
diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c
index cf3bc30..dc06664 100644
--- a/drivers/usb/serial/whiteheat.c
+++ b/drivers/usb/serial/whiteheat.c
@@ -156,7 +156,7 @@ static void whiteheat_unthrottle	(struct usb_serial_port *port);
 static void whiteheat_read_callback	(struct urb *urb, struct pt_regs *regs);
 static void whiteheat_write_callback	(struct urb *urb, struct pt_regs *regs);
 
-static struct usb_serial_device_type whiteheat_fake_device = {
+static struct usb_serial_driver whiteheat_fake_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Connect Tech - WhiteHEAT - (prerenumeration)",
 	.short_name =		"whiteheatnofirm",
@@ -169,7 +169,7 @@ static struct usb_serial_device_type whiteheat_fake_device = {
 	.attach =		whiteheat_firmware_attach,
 };
 
-static struct usb_serial_device_type whiteheat_device = {
+static struct usb_serial_driver whiteheat_device = {
 	.owner =		THIS_MODULE,
 	.name =			"Connect Tech - WhiteHEAT",
 	.short_name =		"whiteheat",
-- 
cgit v1.1


From 18fcac353fdc7cd072b0d24c8667042e675a4c11 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB Serial: get rid of the .owner field in usb_serial_driver

Don't duplicate something that's already in struct driver.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/airprime.c         |  4 +++-
 drivers/usb/serial/belkin_sa.c        |  4 +++-
 drivers/usb/serial/bus.c              |  9 ++++-----
 drivers/usb/serial/cp2101.c           |  4 +++-
 drivers/usb/serial/cyberjack.c        |  4 +++-
 drivers/usb/serial/cypress_m8.c       |  8 ++++++--
 drivers/usb/serial/digi_acceleport.c  |  8 ++++++--
 drivers/usb/serial/empeg.c            |  4 +++-
 drivers/usb/serial/ftdi_sio.c         |  4 +++-
 drivers/usb/serial/garmin_gps.c       |  4 +++-
 drivers/usb/serial/generic.c          |  4 +++-
 drivers/usb/serial/hp4x.c             |  4 +++-
 drivers/usb/serial/io_tables.h        | 12 +++++++++---
 drivers/usb/serial/io_ti.c            |  8 ++++++--
 drivers/usb/serial/ipaq.c             |  4 +++-
 drivers/usb/serial/ipw.c              |  4 +++-
 drivers/usb/serial/ir-usb.c           |  4 +++-
 drivers/usb/serial/keyspan.h          | 16 ++++++++++++----
 drivers/usb/serial/keyspan_pda.c      | 12 +++++++++---
 drivers/usb/serial/kl5kusb105.c       |  4 +++-
 drivers/usb/serial/kobil_sct.c        |  4 +++-
 drivers/usb/serial/mct_u232.c         |  4 +++-
 drivers/usb/serial/omninet.c          |  4 +++-
 drivers/usb/serial/option.c           |  4 +++-
 drivers/usb/serial/pl2303.c           |  4 +++-
 drivers/usb/serial/safe_serial.c      |  4 +++-
 drivers/usb/serial/ti_usb_3410_5052.c |  8 ++++++--
 drivers/usb/serial/usb-serial.c       | 22 +++++++++++-----------
 drivers/usb/serial/usb-serial.h       |  5 +++--
 drivers/usb/serial/visor.c            | 12 +++++++++---
 drivers/usb/serial/whiteheat.c        |  8 ++++++--
 31 files changed, 144 insertions(+), 60 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/serial/airprime.c b/drivers/usb/serial/airprime.c
index 104c043..fbc5b9b 100644
--- a/drivers/usb/serial/airprime.c
+++ b/drivers/usb/serial/airprime.c
@@ -31,7 +31,9 @@ static struct usb_driver airprime_driver = {
 };
 
 static struct usb_serial_driver airprime_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"airprime",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
diff --git a/drivers/usb/serial/belkin_sa.c b/drivers/usb/serial/belkin_sa.c
index 6d84de4..4878961 100644
--- a/drivers/usb/serial/belkin_sa.c
+++ b/drivers/usb/serial/belkin_sa.c
@@ -122,7 +122,9 @@ static struct usb_driver belkin_driver = {
 
 /* All of the device info needed for the serial converters */
 static struct usb_serial_driver belkin_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Belkin / Peracom / GoHubs USB Serial Adapter",
 	.short_name =		"belkin",
 	.id_table =		id_table_combined,
diff --git a/drivers/usb/serial/bus.c b/drivers/usb/serial/bus.c
index 5a0bcd3..b8364a8 100644
--- a/drivers/usb/serial/bus.c
+++ b/drivers/usb/serial/bus.c
@@ -57,13 +57,13 @@ static int usb_serial_device_probe (struct device *dev)
 
 	driver = port->serial->type;
 	if (driver->port_probe) {
-		if (!try_module_get(driver->owner)) {
+		if (!try_module_get(driver->driver.owner)) {
 			dev_err(dev, "module get failed, exiting\n");
 			retval = -EIO;
 			goto exit;
 		}
 		retval = driver->port_probe (port);
-		module_put(driver->owner);
+		module_put(driver->driver.owner);
 		if (retval)
 			goto exit;
 	}
@@ -92,13 +92,13 @@ static int usb_serial_device_remove (struct device *dev)
 
 	driver = port->serial->type;
 	if (driver->port_remove) {
-		if (!try_module_get(driver->owner)) {
+		if (!try_module_get(driver->driver.owner)) {
 			dev_err(dev, "module get failed, exiting\n");
 			retval = -EIO;
 			goto exit;
 		}
 		retval = driver->port_remove (port);
-		module_put(driver->owner);
+		module_put(driver->driver.owner);
 	}
 exit:
 	minor = port->number;
@@ -120,7 +120,6 @@ int usb_serial_bus_register(struct usb_serial_driver *driver)
 	driver->driver.bus = &usb_serial_bus_type;
 	driver->driver.probe = usb_serial_device_probe;
 	driver->driver.remove = usb_serial_device_remove;
-	driver->driver.owner = driver->owner;
 
 	retval = driver_register(&driver->driver);
 
diff --git a/drivers/usb/serial/cp2101.c b/drivers/usb/serial/cp2101.c
index 0b45b58..81dd720 100644
--- a/drivers/usb/serial/cp2101.c
+++ b/drivers/usb/serial/cp2101.c
@@ -74,7 +74,9 @@ static struct usb_driver cp2101_driver = {
 };
 
 static struct usb_serial_driver cp2101_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name			= "CP2101",
 	.id_table		= id_table,
 	.num_interrupt_in	= 0,
diff --git a/drivers/usb/serial/cyberjack.c b/drivers/usb/serial/cyberjack.c
index 9f421a3..3441bad 100644
--- a/drivers/usb/serial/cyberjack.c
+++ b/drivers/usb/serial/cyberjack.c
@@ -84,7 +84,9 @@ static struct usb_driver cyberjack_driver = {
 };
 
 static struct usb_serial_driver cyberjack_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Reiner SCT Cyberjack USB card reader",
 	.short_name =		"cyberjack",
 	.id_table =		id_table,
diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c
index 4fb8e59..b4069af 100644
--- a/drivers/usb/serial/cypress_m8.c
+++ b/drivers/usb/serial/cypress_m8.c
@@ -177,7 +177,9 @@ static unsigned int	  cypress_buf_get(struct cypress_buf *cb, char *buf, unsigne
 
 
 static struct usb_serial_driver cypress_earthmate_device = {
-	.owner =			THIS_MODULE,
+	.driver = {
+		.owner =		THIS_MODULE,
+	},
 	.name =				"DeLorme Earthmate USB",
 	.short_name =			"earthmate",
 	.id_table =			id_table_earthmate,
@@ -204,7 +206,9 @@ static struct usb_serial_driver cypress_earthmate_device = {
 };
 
 static struct usb_serial_driver cypress_hidcom_device = {
-	.owner =			THIS_MODULE,
+	.driver = {
+		.owner =		THIS_MODULE,
+	},
 	.name =				"HID->COM RS232 Adapter",
 	.short_name =			"cyphidcom",
 	.id_table =			id_table_cyphidcomrs232,
diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c
index 66feb88..be9b495 100644
--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -504,7 +504,9 @@ static struct usb_driver digi_driver = {
 /* device info needed for the Digi serial converter */
 
 static struct usb_serial_driver digi_acceleport_2_device = {
-	.owner =			THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =				"Digi 2 port USB adapter",
 	.short_name =			"digi_2",
 	.id_table =			id_table_2,
@@ -531,7 +533,9 @@ static struct usb_serial_driver digi_acceleport_2_device = {
 };
 
 static struct usb_serial_driver digi_acceleport_4_device = {
-	.owner =			THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =				"Digi 4 port USB adapter",
 	.short_name =			"digi_4",
 	.id_table =			id_table_4,
diff --git a/drivers/usb/serial/empeg.c b/drivers/usb/serial/empeg.c
index cbea8b3..3e6c4ba 100644
--- a/drivers/usb/serial/empeg.c
+++ b/drivers/usb/serial/empeg.c
@@ -113,7 +113,9 @@ static struct usb_driver empeg_driver = {
 };
 
 static struct usb_serial_driver empeg_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Empeg",
 	.id_table =		id_table,
 	.num_interrupt_in =	0,
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 529e1a7..9d945de 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -563,7 +563,9 @@ static __u32 ftdi_232bm_baud_base_to_divisor (int baud, int base);
 static __u32 ftdi_232bm_baud_to_divisor (int baud);
 
 static struct usb_serial_driver ftdi_sio_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"FTDI USB Serial Device",
 	.short_name =		"ftdi_sio",
 	.id_table =		id_table_combined,
diff --git a/drivers/usb/serial/garmin_gps.c b/drivers/usb/serial/garmin_gps.c
index 7361194..3fd98c0 100644
--- a/drivers/usb/serial/garmin_gps.c
+++ b/drivers/usb/serial/garmin_gps.c
@@ -1470,7 +1470,9 @@ static void garmin_shutdown (struct usb_serial *serial)
 
 /* All of the device info needed */
 static struct usb_serial_driver garmin_device = {
-	.owner               = THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name                = "Garmin GPS usb/tty",
 	.short_name          = "garmin_gps",
 	.id_table            = id_table,
diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c
index 7f567bf..779bea0c 100644
--- a/drivers/usb/serial/generic.c
+++ b/drivers/usb/serial/generic.c
@@ -37,7 +37,9 @@ static struct usb_device_id generic_device_ids[2]; /* Initially all zeroes. */
 
 /* All of the device info needed for the Generic Serial Converter */
 struct usb_serial_driver usb_serial_generic_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Generic",
 	.short_name =		"generic",
 	.id_table =		generic_device_ids,
diff --git a/drivers/usb/serial/hp4x.c b/drivers/usb/serial/hp4x.c
index b494699..4f3cbc0 100644
--- a/drivers/usb/serial/hp4x.c
+++ b/drivers/usb/serial/hp4x.c
@@ -45,7 +45,9 @@ static struct usb_driver hp49gp_driver = {
 };
 
 static struct usb_serial_driver hp49gp_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"HP4X",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
diff --git a/drivers/usb/serial/io_tables.h b/drivers/usb/serial/io_tables.h
index 7314c04..28fb0d4 100644
--- a/drivers/usb/serial/io_tables.h
+++ b/drivers/usb/serial/io_tables.h
@@ -76,7 +76,9 @@ static struct usb_device_id id_table_combined [] = {
 MODULE_DEVICE_TABLE (usb, id_table_combined);
 
 static struct usb_serial_driver edgeport_2port_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner		= THIS_MODULE,
+	},
 	.name			= "Edgeport 2 port adapter",
 	.short_name		= "edgeport_2",
 	.id_table		= edgeport_2port_id_table,
@@ -104,7 +106,9 @@ static struct usb_serial_driver edgeport_2port_device = {
 };
 
 static struct usb_serial_driver edgeport_4port_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner		= THIS_MODULE,
+	},
 	.name			= "Edgeport 4 port adapter",
 	.short_name		= "edgeport_4",
 	.id_table		= edgeport_4port_id_table,
@@ -132,7 +136,9 @@ static struct usb_serial_driver edgeport_4port_device = {
 };
 
 static struct usb_serial_driver edgeport_8port_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner		= THIS_MODULE,
+	},
 	.name			= "Edgeport 8 port adapter",
 	.short_name		= "edgeport_8",
 	.id_table		= edgeport_8port_id_table,
diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c
index 4328cc7..74228a0 100644
--- a/drivers/usb/serial/io_ti.c
+++ b/drivers/usb/serial/io_ti.c
@@ -2983,7 +2983,9 @@ static unsigned int edge_buf_get(struct edge_buf *eb, char *buf,
 
 
 static struct usb_serial_driver edgeport_1port_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name			= "Edgeport TI 1 port adapter",
 	.short_name		= "edgeport_ti_1",
 	.id_table		= edgeport_1port_id_table,
@@ -3011,7 +3013,9 @@ static struct usb_serial_driver edgeport_1port_device = {
 };
 
 static struct usb_serial_driver edgeport_2port_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name			= "Edgeport TI 2 port adapter",
 	.short_name		= "edgeport_ti_2",
 	.id_table		= edgeport_2port_id_table,
diff --git a/drivers/usb/serial/ipaq.c b/drivers/usb/serial/ipaq.c
index 9a79ad8..9aedfb9 100644
--- a/drivers/usb/serial/ipaq.c
+++ b/drivers/usb/serial/ipaq.c
@@ -548,7 +548,9 @@ static struct usb_driver ipaq_driver = {
 
 /* All of the device info needed for the Compaq iPAQ */
 static struct usb_serial_driver ipaq_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"PocketPC PDA",
 	.id_table =		ipaq_id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
diff --git a/drivers/usb/serial/ipw.c b/drivers/usb/serial/ipw.c
index 04524d3..2ba6962 100644
--- a/drivers/usb/serial/ipw.c
+++ b/drivers/usb/serial/ipw.c
@@ -444,7 +444,9 @@ static int ipw_disconnect(struct usb_serial_port *port)
 }
 
 static struct usb_serial_driver ipw_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"IPWireless converter",
 	.short_name =		"ipw",
 	.id_table =		usb_ipw_ids,
diff --git a/drivers/usb/serial/ir-usb.c b/drivers/usb/serial/ir-usb.c
index ecfb206..bf07905 100644
--- a/drivers/usb/serial/ir-usb.c
+++ b/drivers/usb/serial/ir-usb.c
@@ -134,7 +134,9 @@ static struct usb_driver ir_driver = {
 
 
 static struct usb_serial_driver ir_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"IR Dongle",
 	.id_table =		id_table,
 	.num_interrupt_in =	1,
diff --git a/drivers/usb/serial/keyspan.h b/drivers/usb/serial/keyspan.h
index 97e7d9e..124d46e 100644
--- a/drivers/usb/serial/keyspan.h
+++ b/drivers/usb/serial/keyspan.h
@@ -571,7 +571,9 @@ static struct usb_device_id keyspan_4port_ids[] = {
 
 /* Structs for the devices, pre and post renumeration. */
 static struct usb_serial_driver keyspan_pre_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner		= THIS_MODULE,
+	},
 	.name			= "Keyspan - (without firmware)",
 	.short_name		= "keyspan_no_firm",
 	.id_table		= keyspan_pre_ids,
@@ -583,7 +585,9 @@ static struct usb_serial_driver keyspan_pre_device = {
 };
 
 static struct usb_serial_driver keyspan_1port_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner		= THIS_MODULE,
+	},
 	.name			= "Keyspan 1 port adapter",
 	.short_name		= "keyspan_1",
 	.id_table		= keyspan_1port_ids,
@@ -608,7 +612,9 @@ static struct usb_serial_driver keyspan_1port_device = {
 };
 
 static struct usb_serial_driver keyspan_2port_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner		= THIS_MODULE,
+	},
 	.name			= "Keyspan 2 port adapter",
 	.short_name		= "keyspan_2",
 	.id_table		= keyspan_2port_ids,
@@ -633,7 +639,9 @@ static struct usb_serial_driver keyspan_2port_device = {
 };
 
 static struct usb_serial_driver keyspan_4port_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner		= THIS_MODULE,
+	},
 	.name			= "Keyspan 4 port adapter",
 	.short_name		= "keyspan_4",
 	.id_table		= keyspan_4port_ids,
diff --git a/drivers/usb/serial/keyspan_pda.c b/drivers/usb/serial/keyspan_pda.c
index 8fad0e9..389b783 100644
--- a/drivers/usb/serial/keyspan_pda.c
+++ b/drivers/usb/serial/keyspan_pda.c
@@ -784,7 +784,9 @@ static void keyspan_pda_shutdown (struct usb_serial *serial)
 
 #ifdef KEYSPAN
 static struct usb_serial_driver keyspan_pda_fake_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Keyspan PDA - (prerenumeration)",
 	.short_name =		"keyspan_pda_pre",
 	.id_table =		id_table_fake,
@@ -798,7 +800,9 @@ static struct usb_serial_driver keyspan_pda_fake_device = {
 
 #ifdef XIRCOM
 static struct usb_serial_driver xircom_pgs_fake_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Xircom / Entregra PGS - (prerenumeration)",
 	.short_name =		"xircom_no_firm",
 	.id_table =		id_table_fake_xircom,
@@ -811,7 +815,9 @@ static struct usb_serial_driver xircom_pgs_fake_device = {
 #endif
 
 static struct usb_serial_driver keyspan_pda_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Keyspan PDA",
 	.short_name =		"keyspan_pda",
 	.id_table =		id_table_std,
diff --git a/drivers/usb/serial/kl5kusb105.c b/drivers/usb/serial/kl5kusb105.c
index be08270..586108c 100644
--- a/drivers/usb/serial/kl5kusb105.c
+++ b/drivers/usb/serial/kl5kusb105.c
@@ -124,7 +124,9 @@ static struct usb_driver kl5kusb105d_driver = {
 };
 
 static struct usb_serial_driver kl5kusb105d_device = {
-	.owner =             THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =		     "KL5KUSB105D / PalmConnect",
 	.short_name =	     "kl5kusb105d",
 	.id_table =	     id_table,
diff --git a/drivers/usb/serial/kobil_sct.c b/drivers/usb/serial/kobil_sct.c
index 9494434..a9578e0 100644
--- a/drivers/usb/serial/kobil_sct.c
+++ b/drivers/usb/serial/kobil_sct.c
@@ -106,7 +106,9 @@ static struct usb_driver kobil_driver = {
 
 
 static struct usb_serial_driver kobil_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"KOBIL USB smart card terminal",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
diff --git a/drivers/usb/serial/mct_u232.c b/drivers/usb/serial/mct_u232.c
index 94709643..7dcf91c 100644
--- a/drivers/usb/serial/mct_u232.c
+++ b/drivers/usb/serial/mct_u232.c
@@ -133,7 +133,9 @@ static struct usb_driver mct_u232_driver = {
 };
 
 static struct usb_serial_driver mct_u232_device = {
-	.owner =	     THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =		     "MCT U232",
 	.short_name =	     "mct_u232",
 	.id_table =	     id_table_combined,
diff --git a/drivers/usb/serial/omninet.c b/drivers/usb/serial/omninet.c
index 53c0588..f6327cc1 100644
--- a/drivers/usb/serial/omninet.c
+++ b/drivers/usb/serial/omninet.c
@@ -89,7 +89,9 @@ static struct usb_driver omninet_driver = {
 
 
 static struct usb_serial_driver zyxel_omninet_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"ZyXEL - omni.net lcd plus usb",
 	.short_name =		"omninet",
 	.id_table =		id_table,
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 6ec9266..a2b5adf 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -106,7 +106,9 @@ static struct usb_driver option_driver = {
  * recognizes separately, thus num_port=1.
  */
 static struct usb_serial_driver option_3port_device = {
-	.owner             = THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name              = "Option 3G data card",
 	.short_name        = "option",
 	.id_table          = option_ids,
diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index 7134648..beef3c4 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -176,7 +176,9 @@ static unsigned int pl2303_buf_get(struct pl2303_buf *pb, char *buf,
 
 /* All of the device info needed for the PL2303 SIO serial converter */
 static struct usb_serial_driver pl2303_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"PL-2303",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
diff --git a/drivers/usb/serial/safe_serial.c b/drivers/usb/serial/safe_serial.c
index 87871bb..42a86ab 100644
--- a/drivers/usb/serial/safe_serial.c
+++ b/drivers/usb/serial/safe_serial.c
@@ -398,7 +398,9 @@ static int safe_startup (struct usb_serial *serial)
 }
 
 static struct usb_serial_driver safe_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Safe",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index f2efaf6..eab8a6d 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -256,7 +256,9 @@ static struct usb_driver ti_usb_driver = {
 };
 
 static struct usb_serial_driver ti_1port_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name			= "TI USB 3410 1 port adapter",
 	.id_table		= ti_id_table_3410,
 	.num_interrupt_in	= 1,
@@ -283,7 +285,9 @@ static struct usb_serial_driver ti_1port_device = {
 };
 
 static struct usb_serial_driver ti_2port_device = {
-	.owner			= THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name			= "TI USB 5052 2 port adapter",
 	.id_table		= ti_id_table_5052,
 	.num_interrupt_in	= 1,
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index cf083da..08f6003 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -507,7 +507,7 @@ static int serial_open (struct tty_struct *tty, struct file * filp)
 		/* lock this module before we call it
 		 * this may fail, which means we must bail out,
 		 * safe because we are called with BKL held */
-		if (!try_module_get(serial->type->owner)) {
+		if (!try_module_get(serial->type->driver.owner)) {
 			retval = -ENODEV;
 			goto bailout_kref_put;
 		}
@@ -522,7 +522,7 @@ static int serial_open (struct tty_struct *tty, struct file * filp)
 	return 0;
 
 bailout_module_put:
-	module_put(serial->type->owner);
+	module_put(serial->type->driver.owner);
 bailout_kref_put:
 	kref_put(&serial->kref, destroy_serial);
 	port->open_count = 0;
@@ -553,7 +553,7 @@ static void serial_close(struct tty_struct *tty, struct file * filp)
 			port->tty = NULL;
 		}
 
-		module_put(port->serial->type->owner);
+		module_put(port->serial->type->driver.owner);
 	}
 
 	kref_put(&port->serial->kref, destroy_serial);
@@ -718,8 +718,8 @@ static int serial_read_proc (char *page, char **start, off_t off, int count, int
 			continue;
 
 		length += sprintf (page+length, "%d:", i);
-		if (serial->type->owner)
-			length += sprintf (page+length, " module:%s", module_name(serial->type->owner));
+		if (serial->type->driver.owner)
+			length += sprintf (page+length, " module:%s", module_name(serial->type->driver.owner));
 		length += sprintf (page+length, " name:\"%s\"", serial->type->name);
 		length += sprintf (page+length, " vendor:%04x product:%04x", 
 				   le16_to_cpu(serial->dev->descriptor.idVendor), 
@@ -900,7 +900,7 @@ int usb_serial_probe(struct usb_interface *interface,
 	if (type->probe) {
 		const struct usb_device_id *id;
 
-		if (!try_module_get(type->owner)) {
+		if (!try_module_get(type->driver.owner)) {
 			dev_err(&interface->dev, "module get failed, exiting\n");
 			kfree (serial);
 			return -EIO;
@@ -908,7 +908,7 @@ int usb_serial_probe(struct usb_interface *interface,
 
 		id = usb_match_id(interface, type->id_table);
 		retval = type->probe(serial, id);
-		module_put(type->owner);
+		module_put(type->driver.owner);
 
 		if (retval) {
 			dbg ("sub driver rejected device");
@@ -1007,13 +1007,13 @@ int usb_serial_probe(struct usb_interface *interface,
 	if (!num_ports) {
 		/* if this device type has a calc_num_ports function, call it */
 		if (type->calc_num_ports) {
-			if (!try_module_get(type->owner)) {
+			if (!try_module_get(type->driver.owner)) {
 				dev_err(&interface->dev, "module get failed, exiting\n");
 				kfree (serial);
 				return -EIO;
 			}
 			num_ports = type->calc_num_ports (serial);
-			module_put(type->owner);
+			module_put(type->driver.owner);
 		}
 		if (!num_ports)
 			num_ports = type->num_ports;
@@ -1158,12 +1158,12 @@ int usb_serial_probe(struct usb_interface *interface,
 	
 	/* if this device type has an attach function, call it */
 	if (type->attach) {
-		if (!try_module_get(type->owner)) {
+		if (!try_module_get(type->driver.owner)) {
 			dev_err(&interface->dev, "module get failed, exiting\n");
 			goto probe_error;
 		}
 		retval = type->attach (serial);
-		module_put(type->owner);
+		module_put(type->driver.owner);
 		if (retval < 0)
 			goto probe_error;
 		if (retval > 0) {
diff --git a/drivers/usb/serial/usb-serial.h b/drivers/usb/serial/usb-serial.h
index d6738b1..4ca5e0c 100644
--- a/drivers/usb/serial/usb-serial.h
+++ b/drivers/usb/serial/usb-serial.h
@@ -189,7 +189,6 @@ static inline void usb_set_serial_data (struct usb_serial *serial, void *data)
 
 /**
  * usb_serial_driver - describes a usb serial driver
- * @owner: pointer to the module that owns this driver.
  * @name: pointer to a string that describes this driver.  This string used
  *	in the syslog messages when a device is inserted or removed.
  * @short_name: a pointer to a string that describes this driver in
@@ -226,9 +225,11 @@ static inline void usb_set_serial_data (struct usb_serial *serial, void *data)
  * pointers are defined, then the USB serial core code will call them when
  * the corresponding tty port functions are called.  If they are not
  * called, the generic serial function will be used instead.
+ *
+ * The driver.owner field should be set to the module owner of this driver.
+ *
  */
 struct usb_serial_driver {
-	struct module *owner;
 	char	*name;
 	char	*short_name;
 	const struct usb_device_id *id_table;
diff --git a/drivers/usb/serial/visor.c b/drivers/usb/serial/visor.c
index 825451b..0ac0377 100644
--- a/drivers/usb/serial/visor.c
+++ b/drivers/usb/serial/visor.c
@@ -312,7 +312,9 @@ static struct usb_driver visor_driver = {
 
 /* All of the device info needed for the Handspring Visor, and Palm 4.0 devices */
 static struct usb_serial_driver handspring_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Handspring Visor / Palm OS",
 	.short_name =		"visor",
 	.id_table =		id_table,
@@ -340,7 +342,9 @@ static struct usb_serial_driver handspring_device = {
 
 /* All of the device info needed for the Clie UX50, TH55 Palm 5.0 devices */
 static struct usb_serial_driver clie_5_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Sony Clie 5.0",
 	.short_name =		"clie_5",
 	.id_table =		clie_id_5_table,
@@ -368,7 +372,9 @@ static struct usb_serial_driver clie_5_device = {
 
 /* device info for the Sony Clie OS version 3.5 */
 static struct usb_serial_driver clie_3_5_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Sony Clie 3.5",
 	.short_name =		"clie_3.5",
 	.id_table =		clie_id_3_5_table,
diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c
index dc06664..fb95a34 100644
--- a/drivers/usb/serial/whiteheat.c
+++ b/drivers/usb/serial/whiteheat.c
@@ -157,7 +157,9 @@ static void whiteheat_read_callback	(struct urb *urb, struct pt_regs *regs);
 static void whiteheat_write_callback	(struct urb *urb, struct pt_regs *regs);
 
 static struct usb_serial_driver whiteheat_fake_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Connect Tech - WhiteHEAT - (prerenumeration)",
 	.short_name =		"whiteheatnofirm",
 	.id_table =		id_table_prerenumeration,
@@ -170,7 +172,9 @@ static struct usb_serial_driver whiteheat_fake_device = {
 };
 
 static struct usb_serial_driver whiteheat_device = {
-	.owner =		THIS_MODULE,
+	.driver = {
+		.owner =	THIS_MODULE,
+	},
 	.name =			"Connect Tech - WhiteHEAT",
 	.short_name =		"whiteheat",
 	.id_table =		id_table_std,
-- 
cgit v1.1


From 502b95c1cc9e2c855a26f90fc999c5211b8ba957 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB Serial: move old changelog comments out of source code

Create a new file just for these things, as they just get in the
way in the source files.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/ChangeLog.old | 730 +++++++++++++++++++++++++++++++++++++++
 drivers/usb/serial/io_edgeport.c | 219 ------------
 drivers/usb/serial/pl2303.c      |  23 +-
 drivers/usb/serial/usb-serial.c  | 309 +----------------
 drivers/usb/serial/usb-serial.h  |  44 +--
 drivers/usb/serial/visor.c       | 131 +------
 6 files changed, 736 insertions(+), 720 deletions(-)
 create mode 100644 drivers/usb/serial/ChangeLog.old

(limited to 'drivers')

diff --git a/drivers/usb/serial/ChangeLog.old b/drivers/usb/serial/ChangeLog.old
new file mode 100644
index 0000000..c1b2799
--- /dev/null
+++ b/drivers/usb/serial/ChangeLog.old
@@ -0,0 +1,730 @@
+This is the contents of some of the drivers/usb/serial/ files that had  old
+changelog comments.  They were quite old, and out of date, and we don't keep
+them anymore, so I've put them here, away from the source files, in case
+people still care to see them.
+
+- Greg Kroah-Hartman <greg@kroah.com> October 20, 2005
+
+-----------------------------------------------------------------------
+usb-serial.h Change Log comments:
+
+ (03/26/2002) gkh
+	removed the port->tty check from port_paranoia_check() due to serial
+	consoles not having a tty device assigned to them.
+
+ (12/03/2001) gkh
+	removed active from the port structure.
+	added documentation to the usb_serial_device_type structure
+
+ (10/10/2001) gkh
+	added vendor and product to serial structure.  Needed to determine device
+	owner when the device is disconnected.
+
+ (05/30/2001) gkh
+	added sem to port structure and removed port_lock
+
+ (10/05/2000) gkh
+	Added interrupt_in_endpointAddress and bulk_in_endpointAddress to help
+	fix bug with urb->dev not being set properly, now that the usb core
+	needs it.
+
+ (09/11/2000) gkh
+	Added usb_serial_debug_data function to help get rid of #DEBUG in the
+	drivers.
+
+ (08/28/2000) gkh
+	Added port_lock to port structure.
+
+ (08/08/2000) gkh
+	Added open_count to port structure.
+
+ (07/23/2000) gkh
+	Added bulk_out_endpointAddress to port structure.
+
+ (07/19/2000) gkh, pberger, and borchers
+	Modifications to allow usb-serial drivers to be modules.
+
+-----------------------------------------------------------------------
+usb-serial.c Change Log comments:
+
+ (12/10/2002) gkh
+	Split the ports off into their own struct device, and added a
+	usb-serial bus driver.
+
+ (11/19/2002) gkh
+	removed a few #ifdefs for the generic code and cleaned up the failure
+	logic in initialization.
+
+ (10/02/2002) gkh
+	moved the console code to console.c and out of this file.
+
+ (06/05/2002) gkh
+	moved location of startup() call in serial_probe() until after all
+	of the port information and endpoints are initialized.  This makes
+	things easier for some drivers.
+
+ (04/10/2002) gkh
+	added serial_read_proc function which creates a
+	/proc/tty/driver/usb-serial file.
+
+ (03/27/2002) gkh
+	Got USB serial console code working properly and merged into the main
+	version of the tree.  Thanks to Randy Dunlap for the initial version
+	of this code, and for pushing me to finish it up.
+	The USB serial console works with any usb serial driver device.
+
+ (03/21/2002) gkh
+	Moved all manipulation of port->open_count into the core.  Now the
+	individual driver's open and close functions are called only when the
+	first open() and last close() is called.  Making the drivers a bit
+	smaller and simpler.
+	Fixed a bug if a driver didn't have the owner field set.
+
+ (02/26/2002) gkh
+	Moved all locking into the main serial_* functions, instead of having
+	the individual drivers have to grab the port semaphore.  This should
+	reduce races.
+	Reworked the MOD_INC logic a bit to always increment and decrement, even
+	if the generic driver is being used.
+
+ (10/10/2001) gkh
+	usb_serial_disconnect() now sets the serial->dev pointer is to NULL to
+	help prevent child drivers from accessing the device since it is now
+	gone.
+
+ (09/13/2001) gkh
+	Moved generic driver initialize after we have registered with the USB
+	core.  Thanks to Randy Dunlap for pointing this problem out.
+
+ (07/03/2001) gkh
+	Fixed module paramater size.  Thanks to John Brockmeyer for the pointer.
+	Fixed vendor and product getting defined through the MODULE_PARM macro
+	if the Generic driver wasn't compiled in.
+	Fixed problem with generic_shutdown() not being called for drivers that
+	don't have a shutdown() function.
+
+ (06/06/2001) gkh
+	added evil hack that is needed for the prolific pl2303 device due to the
+	crazy way its endpoints are set up.
+
+ (05/30/2001) gkh
+	switched from using spinlock to a semaphore, which fixes lots of problems.
+
+ (04/08/2001) gb
+	Identify version on module load.
+
+ 2001_02_05 gkh
+	Fixed buffer overflows bug with the generic serial driver.  Thanks to
+	Todd Squires <squirest@ct0.com> for fixing this.
+
+ (01/10/2001) gkh
+	Fixed bug where the generic serial adaptor grabbed _any_ device that was
+	offered to it.
+
+ (12/12/2000) gkh
+	Removed MOD_INC and MOD_DEC from poll and disconnect functions, and
+	moved them to the serial_open and serial_close functions.
+	Also fixed bug with there not being a MOD_DEC for the generic driver
+	(thanks to Gary Brubaker for finding this.)
+
+ (11/29/2000) gkh
+	Small NULL pointer initialization cleanup which saves a bit of disk image
+
+ (11/01/2000) Adam J. Richter
+	instead of using idVendor/idProduct pairs, usb serial drivers
+	now identify their hardware interest with usb_device_id tables,
+	which they usually have anyhow for use with MODULE_DEVICE_TABLE.
+
+ (10/05/2000) gkh
+	Fixed bug with urb->dev not being set properly, now that the usb
+	core needs it.
+
+ (09/11/2000) gkh
+	Removed DEBUG #ifdefs with call to usb_serial_debug_data
+
+ (08/28/2000) gkh
+	Added port_lock to port structure.
+	Added locks for SMP safeness to generic driver
+	Fixed the ability to open a generic device's port more than once.
+
+ (07/23/2000) gkh
+	Added bulk_out_endpointAddress to port structure.
+
+ (07/19/2000) gkh, pberger, and borchers
+	Modifications to allow usb-serial drivers to be modules.
+
+ (07/03/2000) gkh
+	Added more debugging to serial_ioctl call
+
+ (06/25/2000) gkh
+	Changed generic_write_bulk_callback to not call wake_up_interruptible
+	directly, but to have port_softint do it at a safer time.
+
+ (06/23/2000) gkh
+	Cleaned up debugging statements in a quest to find UHCI timeout bug.
+
+ (05/22/2000) gkh
+	Changed the makefile, enabling the big CONFIG_USB_SERIAL_SOMTHING to be
+	removed from the individual device source files.
+
+ (05/03/2000) gkh
+	Added the Digi Acceleport driver from Al Borchers and Peter Berger.
+
+ (05/02/2000) gkh
+	Changed devfs and tty register code to work properly now. This was based on
+	the ACM driver changes by Vojtech Pavlik.
+
+ (04/27/2000) Ryan VanderBijl
+ 	Put calls to *_paranoia_checks into one function.
+
+ (04/23/2000) gkh
+	Fixed bug that Randy Dunlap found for Generic devices with no bulk out ports.
+	Moved when the startup code printed out the devices that are supported.
+
+ (04/19/2000) gkh
+	Added driver for ZyXEL omni.net lcd plus ISDN TA
+	Made startup info message specify which drivers were compiled in.
+
+ (04/03/2000) gkh
+	Changed the probe process to remove the module unload races.
+	Changed where the tty layer gets initialized to have devfs work nicer.
+	Added initial devfs support.
+
+ (03/26/2000) gkh
+	Split driver up into device specific pieces.
+
+ (03/19/2000) gkh
+	Fixed oops that could happen when device was removed while a program
+	was talking to the device.
+	Removed the static urbs and now all urbs are created and destroyed
+	dynamically.
+	Reworked the internal interface. Now everything is based on the
+	usb_serial_port structure instead of the larger usb_serial structure.
+	This fixes the bug that a multiport device could not have more than
+	one port open at one time.
+
+ (03/17/2000) gkh
+	Added config option for debugging messages.
+	Added patch for keyspan pda from Brian Warner.
+
+ (03/06/2000) gkh
+	Added the keyspan pda code from Brian Warner <warner@lothar.com>
+	Moved a bunch of the port specific stuff into its own structure. This
+	is in anticipation of the true multiport devices (there's a bug if you
+	try to access more than one port of any multiport device right now)
+
+ (02/21/2000) gkh
+	Made it so that any serial devices only have to specify which functions
+	they want to overload from the generic function calls (great,
+	inheritance in C, in a driver, just what I wanted...)
+	Added support for set_termios and ioctl function calls. No drivers take
+	advantage of this yet.
+	Removed the #ifdef MODULE, now there is no module specific code.
+	Cleaned up a few comments in usb-serial.h that were wrong (thanks again
+	to Miles Lott).
+	Small fix to get_free_serial.
+
+ (02/14/2000) gkh
+	Removed the Belkin and Peracom functionality from the driver due to
+	the lack of support from the vendor, and me not wanting people to
+	accidenatly buy the device, expecting it to work with Linux.
+	Added read_bulk_callback and write_bulk_callback to the type structure
+	for the needs of the FTDI and WhiteHEAT driver.
+	Changed all reverences to FTDI to FTDI_SIO at the request of Bill
+	Ryder.
+	Changed the output urb size back to the max endpoint size to make
+	the ftdi_sio driver have it easier, and due to the fact that it didn't
+	really increase the speed any.
+
+ (02/11/2000) gkh
+	Added VISOR_FUNCTION_CONSOLE to the visor startup function. This was a
+	patch from Miles Lott (milos@insync.net).
+	Fixed bug with not restoring the minor range that a device grabs, if
+	the startup function fails (thanks Miles for finding this).
+
+ (02/05/2000) gkh
+	Added initial framework for the Keyspan PDA serial converter so that
+	Brian Warner has a place to put his code.
+	Made the ezusb specific functions generic enough that different
+	devices can use them (whiteheat and keyspan_pda both need them).
+	Split out a whole bunch of structure and other stuff to a separate
+	usb-serial.h file.
+	Made the Visor connection messages a little more understandable, now
+	that Miles Lott (milos@insync.net) has gotten the Generic channel to
+	work. Also made them always show up in the log file.
+
+ (01/25/2000) gkh
+	Added initial framework for FTDI serial converter so that Bill Ryder
+	has a place to put his code.
+	Added the vendor specific info from Handspring. Now we can print out
+	informational debug messages as well as understand what is happening.
+
+ (01/23/2000) gkh
+	Fixed problem of crash when trying to open a port that didn't have a
+	device assigned to it. Made the minor node finding a little smarter,
+	now it looks to find a continuous space for the new device.
+
+ (01/21/2000) gkh
+	Fixed bug in visor_startup with patch from Miles Lott (milos@insync.net)
+	Fixed get_serial_by_minor which was all messed up for multi port
+	devices. Fixed multi port problem for generic devices. Now the number
+	of ports is determined by the number of bulk out endpoints for the
+	generic device.
+
+ (01/19/2000) gkh
+	Removed lots of cruft that was around from the old (pre urb) driver
+	interface.
+	Made the serial_table dynamic. This should save lots of memory when
+	the number of minor nodes goes up to 256.
+	Added initial support for devices that have more than one port.
+	Added more debugging comments for the Visor, and added a needed
+	set_configuration call.
+
+ (01/17/2000) gkh
+	Fixed the WhiteHEAT firmware (my processing tool had a bug)
+	and added new debug loader firmware for it.
+	Removed the put_char function as it isn't really needed.
+	Added visor startup commands as found by the Win98 dump.
+
+ (01/13/2000) gkh
+	Fixed the vendor id for the generic driver to the one I meant it to be.
+
+ (01/12/2000) gkh
+	Forget the version numbering...that's pretty useless...
+	Made the driver able to be compiled so that the user can select which
+	converter they want to use. This allows people who only want the Visor
+	support to not pay the memory size price of the WhiteHEAT.
+	Fixed bug where the generic driver (idVendor=0000 and idProduct=0000)
+	grabbed the root hub. Not good.
+
+ version 0.4.0 (01/10/2000) gkh
+	Added whiteheat.h containing the firmware for the ConnectTech WhiteHEAT
+	device. Added startup function to allow firmware to be downloaded to
+	a device if it needs to be.
+	Added firmware download logic to the WhiteHEAT device.
+	Started to add #defines to split up the different drivers for potential
+	configuration option.
+
+ version 0.3.1 (12/30/99) gkh
+      Fixed problems with urb for bulk out.
+      Added initial support for multiple sets of endpoints. This enables
+      the Handspring Visor to be attached successfully. Only the first
+      bulk in / bulk out endpoint pair is being used right now.
+
+ version 0.3.0 (12/27/99) gkh
+	Added initial support for the Handspring Visor based on a patch from
+	Miles Lott (milos@sneety.insync.net)
+	Cleaned up the code a bunch and converted over to using urbs only.
+
+ version 0.2.3 (12/21/99) gkh
+	Added initial support for the Connect Tech WhiteHEAT converter.
+	Incremented the number of ports in expectation of getting the
+	WhiteHEAT to work properly (4 ports per connection).
+	Added notification on insertion and removal of what port the
+	device is/was connected to (and what kind of device it was).
+
+ version 0.2.2 (12/16/99) gkh
+	Changed major number to the new allocated number. We're legal now!
+
+ version 0.2.1 (12/14/99) gkh
+	Fixed bug that happens when device node is opened when there isn't a
+	device attached to it. Thanks to marek@webdesign.no for noticing this.
+
+ version 0.2.0 (11/10/99) gkh
+	Split up internals to make it easier to add different types of serial
+	converters to the code.
+	Added a "generic" driver that gets it's vendor and product id
+	from when the module is loaded. Thanks to David E. Nelson (dnelson@jump.net)
+	for the idea and sample code (from the usb scanner driver.)
+	Cleared up any licensing questions by releasing it under the GNU GPL.
+
+ version 0.1.2 (10/25/99) gkh
+ 	Fixed bug in detecting device.
+
+ version 0.1.1 (10/05/99) gkh
+ 	Changed the major number to not conflict with anything else.
+
+ version 0.1 (09/28/99) gkh
+ 	Can recognize the two different devices and start up a read from
+	device when asked to. Writes also work. No control signals yet, this
+	all is vendor specific data (i.e. no spec), also no control for
+	different baud rates or other bit settings.
+	Currently we are using the same devid as the acm driver. This needs
+	to change.
+
+-----------------------------------------------------------------------
+visor.c Change Log comments:
+
+ (06/03/2003) Judd Montgomery <judd at jpilot.org>
+     Added support for module parameter options for untested/unknown
+     devices.
+
+ (03/09/2003) gkh
+	Added support for the Sony Clie NZ90V device.  Thanks to Martin Brachtl
+	<brachtl@redgrep.cz> for the information.
+
+ (03/05/2003) gkh
+	Think Treo support is now working.
+
+ (04/03/2002) gkh
+	Added support for the Sony OS 4.1 devices.  Thanks to Hiroyuki ARAKI
+	<hiro@zob.ne.jp> for the information.
+
+ (03/27/2002) gkh
+	Removed assumptions that port->tty was always valid (is not true
+	for usb serial console devices.)
+
+ (03/23/2002) gkh
+	Added support for the Palm i705 device, thanks to Thomas Riemer
+	<tom@netmech.com> for the information.
+
+ (03/21/2002) gkh
+	Added support for the Palm m130 device, thanks to Udo Eisenbarth
+	<udo.eisenbarth@web.de> for the information.
+
+ (02/27/2002) gkh
+	Reworked the urb handling logic.  We have no more pool, but dynamically
+	allocate the urb and the transfer buffer on the fly.  In testing this
+	does not incure any measurable overhead.  This also relies on the fact
+	that we have proper reference counting logic for urbs.
+
+ (02/21/2002) SilaS
+  Added initial support for the Palm m515 devices.
+
+ (02/14/2002) gkh
+	Added support for the Clie S-360 device.
+
+ (12/18/2001) gkh
+	Added better Clie support for 3.5 devices.  Thanks to Geoffrey Levand
+	for the patch.
+
+ (11/11/2001) gkh
+	Added support for the m125 devices, and added check to prevent oopses
+	for Clié devices that lie about the number of ports they have.
+
+ (08/30/2001) gkh
+	Added support for the Clie devices, both the 3.5 and 4.0 os versions.
+	Many thanks to Daniel Burke, and Bryan Payne for helping with this.
+
+ (08/23/2001) gkh
+	fixed a few potential bugs pointed out by Oliver Neukum.
+
+ (05/30/2001) gkh
+	switched from using spinlock to a semaphore, which fixes lots of problems.
+
+ (05/28/2000) gkh
+	Added initial support for the Palm m500 and Palm m505 devices.
+
+ (04/08/2001) gb
+	Identify version on module load.
+
+ (01/21/2000) gkh
+	Added write_room and chars_in_buffer, as they were previously using the
+	generic driver versions which is all wrong now that we are using an urb
+	pool.  Thanks to Wolfgang Grandegger for pointing this out to me.
+	Removed count assignment in the write function, which was not needed anymore
+	either.  Thanks to Al Borchers for pointing this out.
+
+ (12/12/2000) gkh
+	Moved MOD_DEC to end of visor_close to be nicer, as the final write
+	message can sleep.
+
+ (11/12/2000) gkh
+	Fixed bug with data being dropped on the floor by forcing tty->low_latency
+	to be on.  Hopefully this fixes the OHCI issue!
+
+ (11/01/2000) Adam J. Richter
+	usb_device_id table support
+
+ (10/05/2000) gkh
+	Fixed bug with urb->dev not being set properly, now that the usb
+	core needs it.
+
+ (09/11/2000) gkh
+	Got rid of always calling kmalloc for every urb we wrote out to the
+	device.
+	Added visor_read_callback so we can keep track of bytes in and out for
+	those people who like to know the speed of their device.
+	Removed DEBUG #ifdefs with call to usb_serial_debug_data
+
+ (09/06/2000) gkh
+	Fixed oops in visor_exit.  Need to uncomment usb_unlink_urb call _after_
+	the host controller drivers set urb->dev = NULL when the urb is finished.
+
+ (08/28/2000) gkh
+	Added locks for SMP safeness.
+
+ (08/08/2000) gkh
+	Fixed endian problem in visor_startup.
+	Fixed MOD_INC and MOD_DEC logic and the ability to open a port more
+	than once.
+
+ (07/23/2000) gkh
+	Added pool of write urbs to speed up transfers to the visor.
+
+ (07/19/2000) gkh
+	Added module_init and module_exit functions to handle the fact that this
+	driver is a loadable module now.
+
+ (07/03/2000) gkh
+	Added visor_set_ioctl and visor_set_termios functions (they don't do much
+	of anything, but are good for debugging.)
+
+ (06/25/2000) gkh
+	Fixed bug in visor_unthrottle that should help with the disconnect in PPP
+	bug that people have been reporting.
+
+ (06/23/2000) gkh
+	Cleaned up debugging statements in a quest to find UHCI timeout bug.
+
+ (04/27/2000) Ryan VanderBijl
+ 	Fixed memory leak in visor_close
+
+ (03/26/2000) gkh
+	Split driver up into device specific pieces.
+
+-----------------------------------------------------------------------
+pl2303.c Change Log comments:
+
+ 2002_Mar_26 gkh
+	allowed driver to work properly if there is no tty assigned to a port
+	(this happens for serial console devices.)
+
+ 2001_Oct_06 gkh
+	Added RTS and DTR line control.  Thanks to joe@bndlg.de for parts of it.
+
+ 2001_Sep_19 gkh
+	Added break support.
+
+ 2001_Aug_30 gkh
+	fixed oops in write_bulk_callback.
+
+ 2001_Aug_28 gkh
+	reworked buffer logic to be like other usb-serial drivers.  Hopefully
+	removing some reported problems.
+
+ 2001_Jun_06 gkh
+	finished porting to 2.4 format.
+
+
+-----------------------------------------------------------------------
+io_edgeport.c Change Log comments:
+
+ 2003_04_03 al borchers
+  - fixed a bug (that shows up with dosemu) where the tty struct is
+    used in a callback after it has been freed
+
+ 2.3 2002_03_08 greg kroah-hartman
+	- fixed bug when multiple devices were attached at the same time.
+
+ 2.2 2001_11_14 greg kroah-hartman
+	- fixed bug in edge_close that kept the port from being used more
+	  than once.
+	- fixed memory leak on device removal.
+	- fixed potential double free of memory when command urb submitting
+	  failed.
+	- other small cleanups when the device is removed
+
+ 2.1 2001_07_09 greg kroah-hartman
+	- added support for TIOCMBIS and TIOCMBIC.
+
+     (04/08/2001) gb
+	- Identify version on module load.
+
+ 2.0 2001_03_05 greg kroah-hartman
+	- reworked entire driver to fit properly in with the other usb-serial
+	  drivers.  Occasional oopses still happen, but it's a good start.
+
+ 1.2.3 (02/23/2001) greg kroah-hartman
+	- changed device table to work properly for 2.4.x final format.
+	- fixed problem with dropping data at high data rates.
+
+ 1.2.2 (11/27/2000) greg kroah-hartman
+	- cleaned up more NTisms.
+	- Added device table for 2.4.0-test11
+
+ 1.2.1 (11/08/2000) greg kroah-hartman
+	- Started to clean up NTisms.
+	- Fixed problem with dev field of urb for kernels >= 2.4.0-test9
+
+ 1.2 (10/17/2000) David Iacovelli
+ 	Remove all EPIC code and GPL source
+  Fix RELEVANT_IFLAG macro to include flow control
+  changes port configuration changes.
+  Fix redefinition of SERIAL_MAGIC
+  Change all timeout values to 5 seconds
+  Tried to fix the UHCI multiple urb submission, but failed miserably.
+  it seems to work fine with OHCI.
+  ( Greg take a look at the #if 0 at end of WriteCmdUsb() we must
+    find a way to work arount this UHCI bug )
+
+ 1.1 (10/11/2000) David Iacovelli
+  Fix XON/XOFF flow control to support both IXON and IXOFF
+
+ 0.9.27 (06/30/2000) David Iacovelli
+  Added transmit queue and now allocate urb for command writes.
+
+ 0.9.26 (06/29/2000) David Iacovelli
+  Add support for 80251 based edgeport
+
+ 0.9.25 (06/27/2000) David Iacovelli
+  Do not close the port if it has multiple opens.
+
+ 0.9.24 (05/26/2000) David Iacovelli
+  Add IOCTLs to support RXTX and JAVA POS
+  and first cut at running BlackBox Demo
+
+ 0.9.23 (05/24/2000) David Iacovelli
+  Add IOCTLs to support RXTX and JAVA POS
+
+ 0.9.22 (05/23/2000) David Iacovelli
+  fixed bug in enumeration.  If epconfig turns on mapping by
+  path after a device is already plugged in, we now update
+  the mapping correctly
+
+ 0.9.21 (05/16/2000) David Iacovelli
+  Added BlockUntilChaseResp() to also wait for txcredits
+  Updated the way we allocate and handle write URBs
+	Add debug code to dump buffers
+
+ 0.9.20 (05/01/2000) David Iacovelli
+	change driver to use usb/tts/
+
+ 0.9.19 (05/01/2000) David Iacovelli
+  Update code to compile if DEBUG is off
+
+ 0.9.18 (04/28/2000) David Iacovelli
+  cleanup and test tty_register with devfs
+
+ 0.9.17 (04/27/2000) greg kroah-hartman
+ 	changed tty_register around to be like the way it
+ 	was before, but now it works properly with devfs.
+
+ 0.9.16 (04/26/2000) david iacovelli
+  Fixed bug in GetProductInfo()
+
+ 0.9.15 (04/25/2000) david iacovelli
+	Updated enumeration
+
+ 0.9.14 (04/24/2000) david iacovelli
+  Removed all config/status IOCTLS and
+  converted to using /proc/edgeport
+  still playing with devfs
+
+ 0.9.13 (04/24/2000) david iacovelli
+  Removed configuration based on ttyUSB0
+  Added support for configuration using /prod/edgeport
+  first attempt at using devfs (not working yet!)
+  Added IOCTL to GetProductInfo()
+  Added support for custom baud rates
+	Add support for random port numbers
+
+ 0.9.12 (04/18/2000) david iacovelli
+	added additional configuration IOCTLs
+  use ttyUSB0 for configuration
+
+ 0.9.11 (04/17/2000) greg kroah-hartman
+	fixed module initialization race conditions.
+	made all urbs dynamically allocated.
+	made driver devfs compatible. now it only registers the tty device
+	when the device is actually plugged in.
+
+ 0.9.10 (04/13/2000) greg kroah-hartman
+	added proc interface framework.
+
+ 0.9.9 (04/13/2000) david iacovelli
+	added enumeration code and ioctls to configure the device
+
+ 0.9.8 (04/12/2000) david iacovelli
+  Change interrupt read start when device is plugged in
+  and stop when device is removed
+	process interrupt reads when all ports are closed
+  (keep value of rxBytesAvail consistent with the edgeport)
+  set the USB_BULK_QUEUE flag so that we can shove a bunch
+  of urbs at once down the pipe
+
+ 0.9.7 (04/10/2000) david iacovelli
+ 	start to add enumeration code.
+  generate serial number for epic devices
+  add support for kdb
+
+ 0.9.6 (03/30/2000) david iacovelli
+  add IOCTL to get string, manufacture, and boot descriptors
+
+ 0.9.5 (03/14/2000) greg kroah-hartman
+	more error checking added to SerialOpen to try to fix UHCI open problem
+
+ 0.9.4 (03/09/2000) greg kroah-hartman
+	added more error checking to handle oops when data is hanging
+	around and tty is abruptly closed.
+
+ 0.9.3 (03/09/2000) david iacovelli
+	Add epic support for xon/xoff chars
+	play with performance
+
+ 0.9.2 (03/08/2000) greg kroah-hartman
+	changed most "info" calls to "dbg"
+	implemented flow control properly in the termios call
+
+ 0.9.1 (03/08/2000) david iacovelli
+	added EPIC support
+	enabled bootloader update
+
+ 0.9 (03/08/2000) greg kroah-hartman
+	Release to IO networks.
+	Integrated changes that David made
+  made getting urbs for writing SMP safe
+
+ 0.8 (03/07/2000) greg kroah-hartman
+	Release to IO networks.
+	Fixed problems that were seen in code by David.
+  Now both Edgeport/4 and Edgeport/2 works properly.
+  Changed most of the functions to use port instead of serial.
+
+ 0.7 (02/27/2000) greg kroah-hartman
+	Milestone 3 release.
+	Release to IO Networks
+	ioctl for waiting on line change implemented.
+	ioctl for getting statistics implemented.
+	multiport support working.
+	lsr and msr registers are now handled properly.
+	change break now hooked up and working.
+	support for all known Edgeport devices.
+
+ 0.6 (02/22/2000) greg kroah-hartman
+	Release to IO networks.
+	CHASE is implemented correctly when port is closed.
+	SerialOpen now blocks correctly until port is fully opened.
+
+ 0.5 (02/20/2000) greg kroah-hartman
+	Release to IO networks.
+	Known problems:
+		modem status register changes are not sent on to the user
+		CHASE is not implemented when the port is closed.
+
+ 0.4 (02/16/2000) greg kroah-hartman
+	Second cut at the CeBit demo.
+	Doesn't leak memory on every write to the port
+	Still small leaks on startup.
+	Added support for Edgeport/2 and Edgeport/8
+
+ 0.3 (02/15/2000) greg kroah-hartman
+	CeBit demo release.
+	Force the line settings to 4800, 8, 1, e for the demo.
+	Warning! This version leaks memory like crazy!
+
+ 0.2 (01/30/2000) greg kroah-hartman
+	Milestone 1 release.
+	Device is found by USB subsystem, enumerated, fimware is downloaded
+	and the descriptors are printed to the debug log, config is set, and
+	green light starts to blink. Open port works, and data can be sent
+	and received at the default settings of the UART. Loopback connector
+	and debug log confirms this.
+
+ 0.1 (01/23/2000) greg kroah-hartman
+	Initial release to help IO Networks try to set up their test system.
+	Edgeport4 is recognized, firmware is downloaded, config is set so
+	device blinks green light every 3 sec. Port is bound, but opening,
+	closing, and sending data do not work properly.
+
+
diff --git a/drivers/usb/serial/io_edgeport.c b/drivers/usb/serial/io_edgeport.c
index 04bfe27..dc4c498 100644
--- a/drivers/usb/serial/io_edgeport.c
+++ b/drivers/usb/serial/io_edgeport.c
@@ -27,225 +27,6 @@
  * Networks technical support, or Peter Berger <pberger@brimson.com>,
  * or Al Borchers <alborchers@steinerpoint.com>.
  *
- * Version history:
- * 
- * 2003_04_03 al borchers
- *  - fixed a bug (that shows up with dosemu) where the tty struct is
- *    used in a callback after it has been freed
- *
- * 2.3 2002_03_08 greg kroah-hartman
- *	- fixed bug when multiple devices were attached at the same time.
- *
- * 2.2 2001_11_14 greg kroah-hartman
- *	- fixed bug in edge_close that kept the port from being used more
- *	  than once.
- *	- fixed memory leak on device removal.
- *	- fixed potential double free of memory when command urb submitting
- *	  failed.
- *	- other small cleanups when the device is removed
- *	
- * 2.1 2001_07_09 greg kroah-hartman
- *	- added support for TIOCMBIS and TIOCMBIC.
- *
- *     (04/08/2001) gb
- *	- Identify version on module load.
- *
- * 2.0 2001_03_05 greg kroah-hartman
- *	- reworked entire driver to fit properly in with the other usb-serial
- *	  drivers.  Occasional oopses still happen, but it's a good start.
- *
- * 1.2.3 (02/23/2001) greg kroah-hartman
- *	- changed device table to work properly for 2.4.x final format.
- *	- fixed problem with dropping data at high data rates.
- *
- * 1.2.2 (11/27/2000) greg kroah-hartman
- *	- cleaned up more NTisms.
- *	- Added device table for 2.4.0-test11
- *
- * 1.2.1 (11/08/2000) greg kroah-hartman
- *	- Started to clean up NTisms.
- *	- Fixed problem with dev field of urb for kernels >= 2.4.0-test9
- *
- * 1.2 (10/17/2000) David Iacovelli
- * 	Remove all EPIC code and GPL source
- *  Fix RELEVANT_IFLAG macro to include flow control 
- *  changes port configuration changes.
- *  Fix redefinition of SERIAL_MAGIC
- *  Change all timeout values to 5 seconds
- *  Tried to fix the UHCI multiple urb submission, but failed miserably.
- *  it seems to work fine with OHCI.
- *  ( Greg take a look at the #if 0 at end of WriteCmdUsb() we must 
- *    find a way to work arount this UHCI bug )
- *
- * 1.1 (10/11/2000) David Iacovelli
- *  Fix XON/XOFF flow control to support both IXON and IXOFF
- *
- * 0.9.27 (06/30/2000) David Iacovelli
- *  Added transmit queue and now allocate urb for command writes.
- *
- * 0.9.26 (06/29/2000) David Iacovelli
- *  Add support for 80251 based edgeport
- *
- * 0.9.25 (06/27/2000) David Iacovelli
- *  Do not close the port if it has multiple opens.
- *
- * 0.9.24 (05/26/2000) David Iacovelli
- *  Add IOCTLs to support RXTX and JAVA POS 
- *  and first cut at running BlackBox Demo
- *
- * 0.9.23 (05/24/2000) David Iacovelli
- *  Add IOCTLs to support RXTX and JAVA POS
- *
- * 0.9.22 (05/23/2000) David Iacovelli
- *  fixed bug in enumeration.  If epconfig turns on mapping by
- *  path after a device is already plugged in, we now update
- *  the mapping correctly
- *
- * 0.9.21 (05/16/2000) David Iacovelli
- *  Added BlockUntilChaseResp() to also wait for txcredits
- *  Updated the way we allocate and handle write URBs 
- *	Add debug code to dump buffers
- *
- * 0.9.20 (05/01/2000) David Iacovelli
- *	change driver to use usb/tts/
- *
- * 0.9.19 (05/01/2000) David Iacovelli
- *  Update code to compile if DEBUG is off
- *
- * 0.9.18 (04/28/2000) David Iacovelli
- *  cleanup and test tty_register with devfs
- *
- * 0.9.17 (04/27/2000) greg kroah-hartman
- * 	changed tty_register around to be like the way it
- * 	was before, but now it works properly with devfs.
- *
- * 0.9.16 (04/26/2000) david iacovelli
- *  Fixed bug in GetProductInfo()
- *
- * 0.9.15 (04/25/2000) david iacovelli
- *	Updated enumeration
- *
- * 0.9.14 (04/24/2000) david iacovelli
- *  Removed all config/status IOCTLS and 
- *  converted to using /proc/edgeport
- *  still playing with devfs
- *
- * 0.9.13 (04/24/2000) david iacovelli
- *  Removed configuration based on ttyUSB0
- *  Added support for configuration using /prod/edgeport
- *  first attempt at using devfs (not working yet!)
- *  Added IOCTL to GetProductInfo()
- *  Added support for custom baud rates
- *	Add support for random port numbers
- *
- * 0.9.12 (04/18/2000) david iacovelli
- *	added additional configuration IOCTLs
- *  use ttyUSB0 for configuration
- *
- * 0.9.11 (04/17/2000) greg kroah-hartman
- *	fixed module initialization race conditions.
- *	made all urbs dynamically allocated.
- *	made driver devfs compatible. now it only registers the tty device
- *	when the device is actually plugged in.
- *
- * 0.9.10 (04/13/2000) greg kroah-hartman
- *	added proc interface framework.
- *
- * 0.9.9 (04/13/2000) david iacovelli
- *	added enumeration code and ioctls to configure the device
- *
- * 0.9.8 (04/12/2000) david iacovelli
- *  Change interrupt read start when device is plugged in
- *  and stop when device is removed
- *	process interrupt reads when all ports are closed 
- *  (keep value of rxBytesAvail consistent with the edgeport)
- *  set the USB_BULK_QUEUE flag so that we can shove a bunch 
- *  of urbs at once down the pipe 
- *
- * 0.9.7 (04/10/2000) david iacovelli
- * 	start to add enumeration code.
- *  generate serial number for epic devices
- *  add support for kdb
- *
- * 0.9.6 (03/30/2000) david iacovelli
- *  add IOCTL to get string, manufacture, and boot descriptors
- *
- * 0.9.5 (03/14/2000) greg kroah-hartman
- *	more error checking added to SerialOpen to try to fix UHCI open problem
- *
- * 0.9.4 (03/09/2000) greg kroah-hartman
- *	added more error checking to handle oops when data is hanging
- *	around and tty is abruptly closed.
- *
- * 0.9.3 (03/09/2000) david iacovelli
- *	Add epic support for xon/xoff chars
- *	play with performance
- *
- * 0.9.2 (03/08/2000) greg kroah-hartman
- *	changed most "info" calls to "dbg"
- *	implemented flow control properly in the termios call
- *
- * 0.9.1 (03/08/2000) david iacovelli
- *	added EPIC support
- *	enabled bootloader update
- *
- * 0.9 (03/08/2000) greg kroah-hartman
- *	Release to IO networks.
- *	Integrated changes that David made
- *  made getting urbs for writing SMP safe
- *
- * 0.8 (03/07/2000) greg kroah-hartman
- *	Release to IO networks.
- *	Fixed problems that were seen in code by David.
- *  Now both Edgeport/4 and Edgeport/2 works properly.
- *  Changed most of the functions to use port instead of serial.
- *
- * 0.7 (02/27/2000) greg kroah-hartman
- *	Milestone 3 release.
- *	Release to IO Networks
- *	ioctl for waiting on line change implemented.
- *	ioctl for getting statistics implemented.
- *	multiport support working.
- *	lsr and msr registers are now handled properly.
- *	change break now hooked up and working.
- *	support for all known Edgeport devices.
- *
- * 0.6 (02/22/2000) greg kroah-hartman
- *	Release to IO networks.
- *	CHASE is implemented correctly when port is closed.
- *	SerialOpen now blocks correctly until port is fully opened.
- *
- * 0.5 (02/20/2000) greg kroah-hartman
- *	Release to IO networks.
- *	Known problems:
- *		modem status register changes are not sent on to the user
- *		CHASE is not implemented when the port is closed.
- *
- * 0.4 (02/16/2000) greg kroah-hartman
- *	Second cut at the CeBit demo.
- *	Doesn't leak memory on every write to the port
- *	Still small leaks on startup.
- *	Added support for Edgeport/2 and Edgeport/8
- *
- * 0.3 (02/15/2000) greg kroah-hartman
- *	CeBit demo release.
- *	Force the line settings to 4800, 8, 1, e for the demo.
- *	Warning! This version leaks memory like crazy!
- *
- * 0.2 (01/30/2000) greg kroah-hartman
- *	Milestone 1 release.
- *	Device is found by USB subsystem, enumerated, fimware is downloaded
- *	and the descriptors are printed to the debug log, config is set, and
- *	green light starts to blink. Open port works, and data can be sent
- *	and received at the default settings of the UART. Loopback connector
- *	and debug log confirms this.
- * 
- * 0.1 (01/23/2000) greg kroah-hartman
- *	Initial release to help IO Networks try to set up their test system. 
- *	Edgeport4 is recognized, firmware is downloaded, config is set so 
- *	device blinks green light every 3 sec. Port is bound, but opening,
- *	closing, and sending data do not work properly.
- * 
  */
 
 #include <linux/config.h>
diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index beef3c4..29719ce 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -8,31 +8,10 @@
  *
  *	This program is free software; you can redistribute it and/or modify
  *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
+ *	the Free Software Foundation; either version 2 of the License.
  *
  * See Documentation/usb/usb-serial.txt for more information on using this driver
  *
- * 2002_Mar_26 gkh
- *	allowed driver to work properly if there is no tty assigned to a port
- *	(this happens for serial console devices.)
- *
- * 2001_Oct_06 gkh
- *	Added RTS and DTR line control.  Thanks to joe@bndlg.de for parts of it.
- *
- * 2001_Sep_19 gkh
- *	Added break support.
- *
- * 2001_Aug_30 gkh
- *	fixed oops in write_bulk_callback.
- *
- * 2001_Aug_28 gkh
- *	reworked buffer logic to be like other usb-serial drivers.  Hopefully
- *	removing some reported problems.
- *
- * 2001_Jun_06 gkh
- *	finished porting to 2.4 format.
- * 
  */
 
 #include <linux/config.h>
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index 08f6003..fde09fb 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -1,7 +1,7 @@
 /*
  * USB Serial Converter driver
  *
- * Copyright (C) 1999 - 2004 Greg Kroah-Hartman (greg@kroah.com)
+ * Copyright (C) 1999 - 2005 Greg Kroah-Hartman (greg@kroah.com)
  * Copyright (C) 2000 Peter Berger (pberger@brimson.com)
  * Copyright (C) 2000 Al Borchers (borchers@steinerpoint.com)
  *
@@ -9,316 +9,11 @@
  *	modify it under the terms of the GNU General Public License version
  *	2 as published by the Free Software Foundation.
  *
- * This driver was originally based on the ACM driver by Armin Fuerst (which was 
+ * This driver was originally based on the ACM driver by Armin Fuerst (which was
  * based on a driver by Brad Keryan)
  *
  * See Documentation/usb/usb-serial.txt for more information on using this driver
  *
- * (12/10/2002) gkh
- *	Split the ports off into their own struct device, and added a
- *	usb-serial bus driver.
- *
- * (11/19/2002) gkh
- *	removed a few #ifdefs for the generic code and cleaned up the failure
- *	logic in initialization.
- *
- * (10/02/2002) gkh
- *	moved the console code to console.c and out of this file.
- *
- * (06/05/2002) gkh
- *	moved location of startup() call in serial_probe() until after all
- *	of the port information and endpoints are initialized.  This makes
- *	things easier for some drivers.
- *
- * (04/10/2002) gkh
- *	added serial_read_proc function which creates a
- *	/proc/tty/driver/usb-serial file.
- *
- * (03/27/2002) gkh
- *	Got USB serial console code working properly and merged into the main
- *	version of the tree.  Thanks to Randy Dunlap for the initial version
- *	of this code, and for pushing me to finish it up.
- *	The USB serial console works with any usb serial driver device.
- *
- * (03/21/2002) gkh
- *	Moved all manipulation of port->open_count into the core.  Now the
- *	individual driver's open and close functions are called only when the
- *	first open() and last close() is called.  Making the drivers a bit
- *	smaller and simpler.
- *	Fixed a bug if a driver didn't have the owner field set.
- *
- * (02/26/2002) gkh
- *	Moved all locking into the main serial_* functions, instead of having 
- *	the individual drivers have to grab the port semaphore.  This should
- *	reduce races.
- *	Reworked the MOD_INC logic a bit to always increment and decrement, even
- *	if the generic driver is being used.
- *
- * (10/10/2001) gkh
- *	usb_serial_disconnect() now sets the serial->dev pointer is to NULL to
- *	help prevent child drivers from accessing the device since it is now
- *	gone.
- *
- * (09/13/2001) gkh
- *	Moved generic driver initialize after we have registered with the USB
- *	core.  Thanks to Randy Dunlap for pointing this problem out.
- *
- * (07/03/2001) gkh
- *	Fixed module paramater size.  Thanks to John Brockmeyer for the pointer.
- *	Fixed vendor and product getting defined through the MODULE_PARM macro
- *	if the Generic driver wasn't compiled in.
- *	Fixed problem with generic_shutdown() not being called for drivers that
- *	don't have a shutdown() function.
- *
- * (06/06/2001) gkh
- *	added evil hack that is needed for the prolific pl2303 device due to the
- *	crazy way its endpoints are set up.
- *
- * (05/30/2001) gkh
- *	switched from using spinlock to a semaphore, which fixes lots of problems.
- *
- * (04/08/2001) gb
- *	Identify version on module load.
- *
- * 2001_02_05 gkh
- *	Fixed buffer overflows bug with the generic serial driver.  Thanks to
- *	Todd Squires <squirest@ct0.com> for fixing this.
- *
- * (01/10/2001) gkh
- *	Fixed bug where the generic serial adaptor grabbed _any_ device that was
- *	offered to it.
- *
- * (12/12/2000) gkh
- *	Removed MOD_INC and MOD_DEC from poll and disconnect functions, and
- *	moved them to the serial_open and serial_close functions.
- *	Also fixed bug with there not being a MOD_DEC for the generic driver
- *	(thanks to Gary Brubaker for finding this.)
- *
- * (11/29/2000) gkh
- *	Small NULL pointer initialization cleanup which saves a bit of disk image
- *
- * (11/01/2000) Adam J. Richter
- *	instead of using idVendor/idProduct pairs, usb serial drivers
- *	now identify their hardware interest with usb_device_id tables,
- *	which they usually have anyhow for use with MODULE_DEVICE_TABLE.
- *
- * (10/05/2000) gkh
- *	Fixed bug with urb->dev not being set properly, now that the usb
- *	core needs it.
- * 
- * (09/11/2000) gkh
- *	Removed DEBUG #ifdefs with call to usb_serial_debug_data
- *
- * (08/28/2000) gkh
- *	Added port_lock to port structure.
- *	Added locks for SMP safeness to generic driver
- *	Fixed the ability to open a generic device's port more than once.
- *
- * (07/23/2000) gkh
- *	Added bulk_out_endpointAddress to port structure.
- *
- * (07/19/2000) gkh, pberger, and borchers
- *	Modifications to allow usb-serial drivers to be modules.
- *
- * (07/03/2000) gkh
- *	Added more debugging to serial_ioctl call
- * 
- * (06/25/2000) gkh
- *	Changed generic_write_bulk_callback to not call wake_up_interruptible
- *	directly, but to have port_softint do it at a safer time.
- *
- * (06/23/2000) gkh
- *	Cleaned up debugging statements in a quest to find UHCI timeout bug.
- *
- * (05/22/2000) gkh
- *	Changed the makefile, enabling the big CONFIG_USB_SERIAL_SOMTHING to be 
- *	removed from the individual device source files.
- *
- * (05/03/2000) gkh
- *	Added the Digi Acceleport driver from Al Borchers and Peter Berger.
- * 
- * (05/02/2000) gkh
- *	Changed devfs and tty register code to work properly now. This was based on
- *	the ACM driver changes by Vojtech Pavlik.
- *
- * (04/27/2000) Ryan VanderBijl
- * 	Put calls to *_paranoia_checks into one function.
- * 
- * (04/23/2000) gkh
- *	Fixed bug that Randy Dunlap found for Generic devices with no bulk out ports.
- *	Moved when the startup code printed out the devices that are supported.
- *
- * (04/19/2000) gkh
- *	Added driver for ZyXEL omni.net lcd plus ISDN TA
- *	Made startup info message specify which drivers were compiled in.
- *
- * (04/03/2000) gkh
- *	Changed the probe process to remove the module unload races.
- *	Changed where the tty layer gets initialized to have devfs work nicer.
- *	Added initial devfs support.
- *
- * (03/26/2000) gkh
- *	Split driver up into device specific pieces.
- * 
- * (03/19/2000) gkh
- *	Fixed oops that could happen when device was removed while a program
- *	was talking to the device.
- *	Removed the static urbs and now all urbs are created and destroyed
- *	dynamically.
- *	Reworked the internal interface. Now everything is based on the 
- *	usb_serial_port structure instead of the larger usb_serial structure.
- *	This fixes the bug that a multiport device could not have more than
- *	one port open at one time.
- *
- * (03/17/2000) gkh
- *	Added config option for debugging messages.
- *	Added patch for keyspan pda from Brian Warner.
- *
- * (03/06/2000) gkh
- *	Added the keyspan pda code from Brian Warner <warner@lothar.com>
- *	Moved a bunch of the port specific stuff into its own structure. This
- *	is in anticipation of the true multiport devices (there's a bug if you
- *	try to access more than one port of any multiport device right now)
- *
- * (02/21/2000) gkh
- *	Made it so that any serial devices only have to specify which functions
- *	they want to overload from the generic function calls (great, 
- *	inheritance in C, in a driver, just what I wanted...)
- *	Added support for set_termios and ioctl function calls. No drivers take
- *	advantage of this yet.
- *	Removed the #ifdef MODULE, now there is no module specific code.
- *	Cleaned up a few comments in usb-serial.h that were wrong (thanks again
- *	to Miles Lott).
- *	Small fix to get_free_serial.
- *
- * (02/14/2000) gkh
- *	Removed the Belkin and Peracom functionality from the driver due to
- *	the lack of support from the vendor, and me not wanting people to 
- *	accidenatly buy the device, expecting it to work with Linux.
- *	Added read_bulk_callback and write_bulk_callback to the type structure
- *	for the needs of the FTDI and WhiteHEAT driver.
- *	Changed all reverences to FTDI to FTDI_SIO at the request of Bill
- *	Ryder.
- *	Changed the output urb size back to the max endpoint size to make
- *	the ftdi_sio driver have it easier, and due to the fact that it didn't
- *	really increase the speed any.
- *
- * (02/11/2000) gkh
- *	Added VISOR_FUNCTION_CONSOLE to the visor startup function. This was a
- *	patch from Miles Lott (milos@insync.net).
- *	Fixed bug with not restoring the minor range that a device grabs, if
- *	the startup function fails (thanks Miles for finding this).
- *
- * (02/05/2000) gkh
- *	Added initial framework for the Keyspan PDA serial converter so that
- *	Brian Warner has a place to put his code.
- *	Made the ezusb specific functions generic enough that different
- *	devices can use them (whiteheat and keyspan_pda both need them).
- *	Split out a whole bunch of structure and other stuff to a separate
- *	usb-serial.h file.
- *	Made the Visor connection messages a little more understandable, now
- *	that Miles Lott (milos@insync.net) has gotten the Generic channel to
- *	work. Also made them always show up in the log file.
- * 
- * (01/25/2000) gkh
- *	Added initial framework for FTDI serial converter so that Bill Ryder
- *	has a place to put his code.
- *	Added the vendor specific info from Handspring. Now we can print out
- *	informational debug messages as well as understand what is happening.
- *
- * (01/23/2000) gkh
- *	Fixed problem of crash when trying to open a port that didn't have a
- *	device assigned to it. Made the minor node finding a little smarter,
- *	now it looks to find a continuous space for the new device.
- *
- * (01/21/2000) gkh
- *	Fixed bug in visor_startup with patch from Miles Lott (milos@insync.net)
- *	Fixed get_serial_by_minor which was all messed up for multi port 
- *	devices. Fixed multi port problem for generic devices. Now the number
- *	of ports is determined by the number of bulk out endpoints for the
- *	generic device.
- *
- * (01/19/2000) gkh
- *	Removed lots of cruft that was around from the old (pre urb) driver 
- *	interface.
- *	Made the serial_table dynamic. This should save lots of memory when
- *	the number of minor nodes goes up to 256.
- *	Added initial support for devices that have more than one port. 
- *	Added more debugging comments for the Visor, and added a needed 
- *	set_configuration call.
- *
- * (01/17/2000) gkh
- *	Fixed the WhiteHEAT firmware (my processing tool had a bug)
- *	and added new debug loader firmware for it.
- *	Removed the put_char function as it isn't really needed.
- *	Added visor startup commands as found by the Win98 dump.
- * 
- * (01/13/2000) gkh
- *	Fixed the vendor id for the generic driver to the one I meant it to be.
- *
- * (01/12/2000) gkh
- *	Forget the version numbering...that's pretty useless...
- *	Made the driver able to be compiled so that the user can select which
- *	converter they want to use. This allows people who only want the Visor
- *	support to not pay the memory size price of the WhiteHEAT.
- *	Fixed bug where the generic driver (idVendor=0000 and idProduct=0000)
- *	grabbed the root hub. Not good.
- * 
- * version 0.4.0 (01/10/2000) gkh
- *	Added whiteheat.h containing the firmware for the ConnectTech WhiteHEAT
- *	device. Added startup function to allow firmware to be downloaded to
- *	a device if it needs to be.
- *	Added firmware download logic to the WhiteHEAT device.
- *	Started to add #defines to split up the different drivers for potential
- *	configuration option.
- *	
- * version 0.3.1 (12/30/99) gkh
- *      Fixed problems with urb for bulk out.
- *      Added initial support for multiple sets of endpoints. This enables
- *      the Handspring Visor to be attached successfully. Only the first
- *      bulk in / bulk out endpoint pair is being used right now.
- *
- * version 0.3.0 (12/27/99) gkh
- *	Added initial support for the Handspring Visor based on a patch from
- *	Miles Lott (milos@sneety.insync.net)
- *	Cleaned up the code a bunch and converted over to using urbs only.
- *
- * version 0.2.3 (12/21/99) gkh
- *	Added initial support for the Connect Tech WhiteHEAT converter.
- *	Incremented the number of ports in expectation of getting the
- *	WhiteHEAT to work properly (4 ports per connection).
- *	Added notification on insertion and removal of what port the
- *	device is/was connected to (and what kind of device it was).
- *
- * version 0.2.2 (12/16/99) gkh
- *	Changed major number to the new allocated number. We're legal now!
- *
- * version 0.2.1 (12/14/99) gkh
- *	Fixed bug that happens when device node is opened when there isn't a
- *	device attached to it. Thanks to marek@webdesign.no for noticing this.
- *
- * version 0.2.0 (11/10/99) gkh
- *	Split up internals to make it easier to add different types of serial 
- *	converters to the code.
- *	Added a "generic" driver that gets it's vendor and product id
- *	from when the module is loaded. Thanks to David E. Nelson (dnelson@jump.net)
- *	for the idea and sample code (from the usb scanner driver.)
- *	Cleared up any licensing questions by releasing it under the GNU GPL.
- *
- * version 0.1.2 (10/25/99) gkh
- * 	Fixed bug in detecting device.
- *
- * version 0.1.1 (10/05/99) gkh
- * 	Changed the major number to not conflict with anything else.
- *
- * version 0.1 (09/28/99) gkh
- * 	Can recognize the two different devices and start up a read from
- *	device when asked to. Writes also work. No control signals yet, this
- *	all is vendor specific data (i.e. no spec), also no control for
- *	different baud rates or other bit settings.
- *	Currently we are using the same devid as the acm driver. This needs
- *	to change.
- * 
  */
 
 #include <linux/config.h>
diff --git a/drivers/usb/serial/usb-serial.h b/drivers/usb/serial/usb-serial.h
index 4ca5e0c..1cedc19 100644
--- a/drivers/usb/serial/usb-serial.h
+++ b/drivers/usb/serial/usb-serial.h
@@ -1,53 +1,13 @@
 /*
  * USB Serial Converter driver
  *
- *	Copyright (C) 1999 - 2004
+ *	Copyright (C) 1999 - 2005
  *	    Greg Kroah-Hartman (greg@kroah.com)
  *
  *	This program is free software; you can redistribute it and/or modify
  *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
+ *	the Free Software Foundation; either version 2 of the License.
  *
- * See Documentation/usb/usb-serial.txt for more information on using this driver
- *
- * (03/26/2002) gkh
- *	removed the port->tty check from port_paranoia_check() due to serial
- *	consoles not having a tty device assigned to them.
- *
- * (12/03/2001) gkh
- *	removed active from the port structure.
- *	added documentation to the usb_serial_device_type structure
- *
- * (10/10/2001) gkh
- *	added vendor and product to serial structure.  Needed to determine device
- *	owner when the device is disconnected.
- *
- * (05/30/2001) gkh
- *	added sem to port structure and removed port_lock
- *
- * (10/05/2000) gkh
- *	Added interrupt_in_endpointAddress and bulk_in_endpointAddress to help
- *	fix bug with urb->dev not being set properly, now that the usb core
- *	needs it.
- * 
- * (09/11/2000) gkh
- *	Added usb_serial_debug_data function to help get rid of #DEBUG in the
- *	drivers.
- *
- * (08/28/2000) gkh
- *	Added port_lock to port structure.
- *
- * (08/08/2000) gkh
- *	Added open_count to port structure.
- *
- * (07/23/2000) gkh
- *	Added bulk_out_endpointAddress to port structure.
- *
- * (07/19/2000) gkh, pberger, and borchers
- *	Modifications to allow usb-serial drivers to be modules.
- *
- * 
  */
 
 
diff --git a/drivers/usb/serial/visor.c b/drivers/usb/serial/visor.c
index 0ac0377..39ad0ca 100644
--- a/drivers/usb/serial/visor.c
+++ b/drivers/usb/serial/visor.c
@@ -7,139 +7,10 @@
  *
  *	This program is free software; you can redistribute it and/or modify
  *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
+ *	the Free Software Foundation; either version 2 of the License.
  *
  * See Documentation/usb/usb-serial.txt for more information on using this driver
  *
- * (06/03/2003) Judd Montgomery <judd at jpilot.org>
- *     Added support for module parameter options for untested/unknown
- *     devices.
- *
- * (03/09/2003) gkh
- *	Added support for the Sony Clie NZ90V device.  Thanks to Martin Brachtl
- *	<brachtl@redgrep.cz> for the information.
- *
- * (03/05/2003) gkh
- *	Think Treo support is now working.
- *
- * (04/03/2002) gkh
- *	Added support for the Sony OS 4.1 devices.  Thanks to Hiroyuki ARAKI
- *	<hiro@zob.ne.jp> for the information.
- *
- * (03/27/2002) gkh
- *	Removed assumptions that port->tty was always valid (is not true
- *	for usb serial console devices.)
- *
- * (03/23/2002) gkh
- *	Added support for the Palm i705 device, thanks to Thomas Riemer
- *	<tom@netmech.com> for the information.
- *
- * (03/21/2002) gkh
- *	Added support for the Palm m130 device, thanks to Udo Eisenbarth
- *	<udo.eisenbarth@web.de> for the information.
- *
- * (02/27/2002) gkh
- *	Reworked the urb handling logic.  We have no more pool, but dynamically
- *	allocate the urb and the transfer buffer on the fly.  In testing this
- *	does not incure any measurable overhead.  This also relies on the fact
- *	that we have proper reference counting logic for urbs.
- *
- * (02/21/2002) SilaS
- *  Added initial support for the Palm m515 devices.
- *
- * (02/14/2002) gkh
- *	Added support for the Clie S-360 device.
- *
- * (12/18/2001) gkh
- *	Added better Clie support for 3.5 devices.  Thanks to Geoffrey Levand
- *	for the patch.
- *
- * (11/11/2001) gkh
- *	Added support for the m125 devices, and added check to prevent oopses
- *	for Clié devices that lie about the number of ports they have.
- *
- * (08/30/2001) gkh
- *	Added support for the Clie devices, both the 3.5 and 4.0 os versions.
- *	Many thanks to Daniel Burke, and Bryan Payne for helping with this.
- *
- * (08/23/2001) gkh
- *	fixed a few potential bugs pointed out by Oliver Neukum.
- *
- * (05/30/2001) gkh
- *	switched from using spinlock to a semaphore, which fixes lots of problems.
- *
- * (05/28/2000) gkh
- *	Added initial support for the Palm m500 and Palm m505 devices.
- *
- * (04/08/2001) gb
- *	Identify version on module load.
- *
- * (01/21/2000) gkh
- *	Added write_room and chars_in_buffer, as they were previously using the
- *	generic driver versions which is all wrong now that we are using an urb
- *	pool.  Thanks to Wolfgang Grandegger for pointing this out to me.
- *	Removed count assignment in the write function, which was not needed anymore
- *	either.  Thanks to Al Borchers for pointing this out.
- *
- * (12/12/2000) gkh
- *	Moved MOD_DEC to end of visor_close to be nicer, as the final write 
- *	message can sleep.
- * 
- * (11/12/2000) gkh
- *	Fixed bug with data being dropped on the floor by forcing tty->low_latency
- *	to be on.  Hopefully this fixes the OHCI issue!
- *
- * (11/01/2000) Adam J. Richter
- *	usb_device_id table support
- * 
- * (10/05/2000) gkh
- *	Fixed bug with urb->dev not being set properly, now that the usb
- *	core needs it.
- * 
- * (09/11/2000) gkh
- *	Got rid of always calling kmalloc for every urb we wrote out to the
- *	device.
- *	Added visor_read_callback so we can keep track of bytes in and out for
- *	those people who like to know the speed of their device.
- *	Removed DEBUG #ifdefs with call to usb_serial_debug_data
- *
- * (09/06/2000) gkh
- *	Fixed oops in visor_exit.  Need to uncomment usb_unlink_urb call _after_
- *	the host controller drivers set urb->dev = NULL when the urb is finished.
- *
- * (08/28/2000) gkh
- *	Added locks for SMP safeness.
- *
- * (08/08/2000) gkh
- *	Fixed endian problem in visor_startup.
- *	Fixed MOD_INC and MOD_DEC logic and the ability to open a port more 
- *	than once.
- * 
- * (07/23/2000) gkh
- *	Added pool of write urbs to speed up transfers to the visor.
- * 
- * (07/19/2000) gkh
- *	Added module_init and module_exit functions to handle the fact that this
- *	driver is a loadable module now.
- *
- * (07/03/2000) gkh
- *	Added visor_set_ioctl and visor_set_termios functions (they don't do much
- *	of anything, but are good for debugging.)
- * 
- * (06/25/2000) gkh
- *	Fixed bug in visor_unthrottle that should help with the disconnect in PPP
- *	bug that people have been reporting.
- *
- * (06/23/2000) gkh
- *	Cleaned up debugging statements in a quest to find UHCI timeout bug.
- *
- * (04/27/2000) Ryan VanderBijl
- * 	Fixed memory leak in visor_close
- *
- * (03/26/2000) gkh
- *	Split driver up into device specific pieces.
- * 
  */
 
 #include <linux/config.h>
-- 
cgit v1.1


From 269bda1c123c7caf88e1deb2264f9086f0344192 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB Serial: move name to driver structure

This fixes up a lot of problems in sysfs with some of the usb serial
drivers, they had incorrect driver names.  Also saves a tiny ammount
of memory.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/airprime.c         |  2 +-
 drivers/usb/serial/belkin_sa.c        |  4 ++--
 drivers/usb/serial/bus.c              |  8 ++------
 drivers/usb/serial/cp2101.c           |  4 ++--
 drivers/usb/serial/cyberjack.c        |  4 ++--
 drivers/usb/serial/cypress_m8.c       |  8 ++++----
 drivers/usb/serial/digi_acceleport.c  | 12 ++++++------
 drivers/usb/serial/empeg.c            |  2 +-
 drivers/usb/serial/ftdi_sio.c         |  4 ++--
 drivers/usb/serial/garmin_gps.c       |  4 ++--
 drivers/usb/serial/generic.c          |  3 +--
 drivers/usb/serial/hp4x.c             |  4 ++--
 drivers/usb/serial/io_tables.h        | 12 ++++++------
 drivers/usb/serial/io_ti.c            | 12 ++++++------
 drivers/usb/serial/ipaq.c             |  3 ++-
 drivers/usb/serial/ipw.c              |  4 ++--
 drivers/usb/serial/ir-usb.c           |  3 ++-
 drivers/usb/serial/keyspan.h          | 16 ++++++++--------
 drivers/usb/serial/keyspan_pda.c      | 12 ++++++------
 drivers/usb/serial/kl5kusb105.c       |  4 ++--
 drivers/usb/serial/kobil_sct.c        |  3 ++-
 drivers/usb/serial/mct_u232.c         |  4 ++--
 drivers/usb/serial/omninet.c          |  4 ++--
 drivers/usb/serial/option.c           |  4 ++--
 drivers/usb/serial/pl2303.c           |  2 +-
 drivers/usb/serial/safe_serial.c      |  2 +-
 drivers/usb/serial/ti_usb_3410_5052.c | 10 ++++++----
 drivers/usb/serial/usb-serial.c       | 15 +++++++++------
 drivers/usb/serial/usb-serial.h       | 12 +++++-------
 drivers/usb/serial/visor.c            | 18 +++++++++---------
 drivers/usb/serial/whiteheat.c        | 30 +++++++++++++++---------------
 31 files changed, 115 insertions(+), 114 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/serial/airprime.c b/drivers/usb/serial/airprime.c
index fbc5b9b..1f29d88 100644
--- a/drivers/usb/serial/airprime.c
+++ b/drivers/usb/serial/airprime.c
@@ -33,8 +33,8 @@ static struct usb_driver airprime_driver = {
 static struct usb_serial_driver airprime_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"airprime",
 	},
-	.name =			"airprime",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		NUM_DONT_CARE,
diff --git a/drivers/usb/serial/belkin_sa.c b/drivers/usb/serial/belkin_sa.c
index 4878961..84bc0ee 100644
--- a/drivers/usb/serial/belkin_sa.c
+++ b/drivers/usb/serial/belkin_sa.c
@@ -124,9 +124,9 @@ static struct usb_driver belkin_driver = {
 static struct usb_serial_driver belkin_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"belkin",
 	},
-	.name =			"Belkin / Peracom / GoHubs USB Serial Adapter",
-	.short_name =		"belkin",
+	.description =		"Belkin / Peracom / GoHubs USB Serial Adapter",
 	.id_table =		id_table_combined,
 	.num_interrupt_in =	1,
 	.num_bulk_in =		1,
diff --git a/drivers/usb/serial/bus.c b/drivers/usb/serial/bus.c
index b8364a8..664139a 100644
--- a/drivers/usb/serial/bus.c
+++ b/drivers/usb/serial/bus.c
@@ -72,7 +72,7 @@ static int usb_serial_device_probe (struct device *dev)
 	tty_register_device (usb_serial_tty_driver, minor, dev);
 	dev_info(&port->serial->dev->dev, 
 		 "%s converter now attached to ttyUSB%d\n",
-		 driver->name, minor);
+		 driver->description, minor);
 
 exit:
 	return retval;
@@ -104,7 +104,7 @@ exit:
 	minor = port->number;
 	tty_unregister_device (usb_serial_tty_driver, minor);
 	dev_info(dev, "%s converter now disconnected from ttyUSB%d\n",
-		 driver->name, minor);
+		 driver->description, minor);
 
 	return retval;
 }
@@ -113,10 +113,6 @@ int usb_serial_bus_register(struct usb_serial_driver *driver)
 {
 	int retval;
 
-	if (driver->short_name)
-		driver->driver.name = (char *)driver->short_name;
-	else
-		driver->driver.name = (char *)driver->name;
 	driver->driver.bus = &usb_serial_bus_type;
 	driver->driver.probe = usb_serial_device_probe;
 	driver->driver.remove = usb_serial_device_remove;
diff --git a/drivers/usb/serial/cp2101.c b/drivers/usb/serial/cp2101.c
index 81dd720..c5334dd 100644
--- a/drivers/usb/serial/cp2101.c
+++ b/drivers/usb/serial/cp2101.c
@@ -67,7 +67,7 @@ MODULE_DEVICE_TABLE (usb, id_table);
 
 static struct usb_driver cp2101_driver = {
 	.owner		= THIS_MODULE,
-	.name		= "CP2101",
+	.name		= "cp2101",
 	.probe		= usb_serial_probe,
 	.disconnect	= usb_serial_disconnect,
 	.id_table	= id_table,
@@ -76,8 +76,8 @@ static struct usb_driver cp2101_driver = {
 static struct usb_serial_driver cp2101_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name = 	"cp2101",
 	},
-	.name			= "CP2101",
 	.id_table		= id_table,
 	.num_interrupt_in	= 0,
 	.num_bulk_in		= 0,
diff --git a/drivers/usb/serial/cyberjack.c b/drivers/usb/serial/cyberjack.c
index 3441bad..e581e4a 100644
--- a/drivers/usb/serial/cyberjack.c
+++ b/drivers/usb/serial/cyberjack.c
@@ -86,9 +86,9 @@ static struct usb_driver cyberjack_driver = {
 static struct usb_serial_driver cyberjack_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"cyberjack",
 	},
-	.name =			"Reiner SCT Cyberjack USB card reader",
-	.short_name =		"cyberjack",
+	.description =		"Reiner SCT Cyberjack USB card reader",
 	.id_table =		id_table,
 	.num_interrupt_in =	1,
 	.num_bulk_in =		1,
diff --git a/drivers/usb/serial/cypress_m8.c b/drivers/usb/serial/cypress_m8.c
index b4069af..af9290e 100644
--- a/drivers/usb/serial/cypress_m8.c
+++ b/drivers/usb/serial/cypress_m8.c
@@ -179,9 +179,9 @@ static unsigned int	  cypress_buf_get(struct cypress_buf *cb, char *buf, unsigne
 static struct usb_serial_driver cypress_earthmate_device = {
 	.driver = {
 		.owner =		THIS_MODULE,
+		.name =			"earthmate",
 	},
-	.name =				"DeLorme Earthmate USB",
-	.short_name =			"earthmate",
+	.description =			"DeLorme Earthmate USB",
 	.id_table =			id_table_earthmate,
 	.num_interrupt_in = 		1,
 	.num_interrupt_out =		1,
@@ -208,9 +208,9 @@ static struct usb_serial_driver cypress_earthmate_device = {
 static struct usb_serial_driver cypress_hidcom_device = {
 	.driver = {
 		.owner =		THIS_MODULE,
+		.name =			"cyphidcom",
 	},
-	.name =				"HID->COM RS232 Adapter",
-	.short_name =			"cyphidcom",
+	.description =			"HID->COM RS232 Adapter",
 	.id_table =			id_table_cyphidcomrs232,
 	.num_interrupt_in =		1,
 	.num_interrupt_out =		1,
diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c
index be9b495..dc74644 100644
--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -505,10 +505,10 @@ static struct usb_driver digi_driver = {
 
 static struct usb_serial_driver digi_acceleport_2_device = {
 	.driver = {
-		.owner =	THIS_MODULE,
+		.owner =		THIS_MODULE,
+		.name =			"digi_2",
 	},
-	.name =				"Digi 2 port USB adapter",
-	.short_name =			"digi_2",
+	.description =			"Digi 2 port USB adapter",
 	.id_table =			id_table_2,
 	.num_interrupt_in =		0,
 	.num_bulk_in =			4,
@@ -534,10 +534,10 @@ static struct usb_serial_driver digi_acceleport_2_device = {
 
 static struct usb_serial_driver digi_acceleport_4_device = {
 	.driver = {
-		.owner =	THIS_MODULE,
+		.owner =		THIS_MODULE,
+		.name =			"digi_4",
 	},
-	.name =				"Digi 4 port USB adapter",
-	.short_name =			"digi_4",
+	.description =			"Digi 4 port USB adapter",
 	.id_table =			id_table_4,
 	.num_interrupt_in =		0,
 	.num_bulk_in =			5,
diff --git a/drivers/usb/serial/empeg.c b/drivers/usb/serial/empeg.c
index 3e6c4ba..0b0546d 100644
--- a/drivers/usb/serial/empeg.c
+++ b/drivers/usb/serial/empeg.c
@@ -115,8 +115,8 @@ static struct usb_driver empeg_driver = {
 static struct usb_serial_driver empeg_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"empeg",
 	},
-	.name =			"Empeg",
 	.id_table =		id_table,
 	.num_interrupt_in =	0,
 	.num_bulk_in =		1,
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 9d945de..77d54ac 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -565,9 +565,9 @@ static __u32 ftdi_232bm_baud_to_divisor (int baud);
 static struct usb_serial_driver ftdi_sio_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"ftdi_sio",
 	},
-	.name =			"FTDI USB Serial Device",
-	.short_name =		"ftdi_sio",
+	.description =		"FTDI USB Serial Device",
 	.id_table =		id_table_combined,
 	.num_interrupt_in =	0,
 	.num_bulk_in =		1,
diff --git a/drivers/usb/serial/garmin_gps.c b/drivers/usb/serial/garmin_gps.c
index 3fd98c0..35820bd 100644
--- a/drivers/usb/serial/garmin_gps.c
+++ b/drivers/usb/serial/garmin_gps.c
@@ -1472,9 +1472,9 @@ static void garmin_shutdown (struct usb_serial *serial)
 static struct usb_serial_driver garmin_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"garmin_gps",
 	},
-	.name                = "Garmin GPS usb/tty",
-	.short_name          = "garmin_gps",
+	.description =		"Garmin GPS usb/tty",
 	.id_table            = id_table,
 	.num_interrupt_in    = 1,
 	.num_bulk_in         = 1,
diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c
index 779bea0c..8909208 100644
--- a/drivers/usb/serial/generic.c
+++ b/drivers/usb/serial/generic.c
@@ -39,9 +39,8 @@ static struct usb_device_id generic_device_ids[2]; /* Initially all zeroes. */
 struct usb_serial_driver usb_serial_generic_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"generic",
 	},
-	.name =			"Generic",
-	.short_name =		"generic",
 	.id_table =		generic_device_ids,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		NUM_DONT_CARE,
diff --git a/drivers/usb/serial/hp4x.c b/drivers/usb/serial/hp4x.c
index 4f3cbc0..8eadfb7 100644
--- a/drivers/usb/serial/hp4x.c
+++ b/drivers/usb/serial/hp4x.c
@@ -38,7 +38,7 @@ MODULE_DEVICE_TABLE(usb, id_table);
 
 static struct usb_driver hp49gp_driver = {
 	.owner =	THIS_MODULE,
-	.name =		"HP4X",
+	.name =		"hp4X",
 	.probe =	usb_serial_probe,
 	.disconnect =	usb_serial_disconnect,
 	.id_table =	id_table,
@@ -47,8 +47,8 @@ static struct usb_driver hp49gp_driver = {
 static struct usb_serial_driver hp49gp_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"hp4X",
 	},
-	.name =			"HP4X",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		NUM_DONT_CARE,
diff --git a/drivers/usb/serial/io_tables.h b/drivers/usb/serial/io_tables.h
index 28fb0d4..fad561c 100644
--- a/drivers/usb/serial/io_tables.h
+++ b/drivers/usb/serial/io_tables.h
@@ -78,9 +78,9 @@ MODULE_DEVICE_TABLE (usb, id_table_combined);
 static struct usb_serial_driver edgeport_2port_device = {
 	.driver = {
 		.owner		= THIS_MODULE,
+		.name		= "edgeport_2",
 	},
-	.name			= "Edgeport 2 port adapter",
-	.short_name		= "edgeport_2",
+	.description		= "Edgeport 2 port adapter",
 	.id_table		= edgeport_2port_id_table,
 	.num_interrupt_in	= 1,
 	.num_bulk_in		= 1,
@@ -108,9 +108,9 @@ static struct usb_serial_driver edgeport_2port_device = {
 static struct usb_serial_driver edgeport_4port_device = {
 	.driver = {
 		.owner		= THIS_MODULE,
+		.name		= "edgeport_4",
 	},
-	.name			= "Edgeport 4 port adapter",
-	.short_name		= "edgeport_4",
+	.description		= "Edgeport 4 port adapter",
 	.id_table		= edgeport_4port_id_table,
 	.num_interrupt_in	= 1,
 	.num_bulk_in		= 1,
@@ -138,9 +138,9 @@ static struct usb_serial_driver edgeport_4port_device = {
 static struct usb_serial_driver edgeport_8port_device = {
 	.driver = {
 		.owner		= THIS_MODULE,
+		.name		= "edgeport_8",
 	},
-	.name			= "Edgeport 8 port adapter",
-	.short_name		= "edgeport_8",
+	.description		= "Edgeport 8 port adapter",
 	.id_table		= edgeport_8port_id_table,
 	.num_interrupt_in	= 1,
 	.num_bulk_in		= 1,
diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c
index 74228a0..832b6d6 100644
--- a/drivers/usb/serial/io_ti.c
+++ b/drivers/usb/serial/io_ti.c
@@ -2984,10 +2984,10 @@ static unsigned int edge_buf_get(struct edge_buf *eb, char *buf,
 
 static struct usb_serial_driver edgeport_1port_device = {
 	.driver = {
-		.owner =	THIS_MODULE,
+		.owner		= THIS_MODULE,
+		.name		= "edgeport_ti_1",
 	},
-	.name			= "Edgeport TI 1 port adapter",
-	.short_name		= "edgeport_ti_1",
+	.description		= "Edgeport TI 1 port adapter",
 	.id_table		= edgeport_1port_id_table,
 	.num_interrupt_in	= 1,
 	.num_bulk_in		= 1,
@@ -3014,10 +3014,10 @@ static struct usb_serial_driver edgeport_1port_device = {
 
 static struct usb_serial_driver edgeport_2port_device = {
 	.driver = {
-		.owner =	THIS_MODULE,
+		.owner		= THIS_MODULE,
+		.name		= "edgeport_ti_2",
 	},
-	.name			= "Edgeport TI 2 port adapter",
-	.short_name		= "edgeport_ti_2",
+	.description		= "Edgeport TI 2 port adapter",
 	.id_table		= edgeport_2port_id_table,
 	.num_interrupt_in	= 1,
 	.num_bulk_in		= 2,
diff --git a/drivers/usb/serial/ipaq.c b/drivers/usb/serial/ipaq.c
index 9aedfb9..1abaebe 100644
--- a/drivers/usb/serial/ipaq.c
+++ b/drivers/usb/serial/ipaq.c
@@ -550,8 +550,9 @@ static struct usb_driver ipaq_driver = {
 static struct usb_serial_driver ipaq_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"ipaq",
 	},
-	.name =			"PocketPC PDA",
+	.description =		"PocketPC PDA",
 	.id_table =		ipaq_id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		1,
diff --git a/drivers/usb/serial/ipw.c b/drivers/usb/serial/ipw.c
index 2ba6962..a02fada 100644
--- a/drivers/usb/serial/ipw.c
+++ b/drivers/usb/serial/ipw.c
@@ -446,9 +446,9 @@ static int ipw_disconnect(struct usb_serial_port *port)
 static struct usb_serial_driver ipw_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"ipw",
 	},
-	.name =			"IPWireless converter",
-	.short_name =		"ipw",
+	.description =		"IPWireless converter",
 	.id_table =		usb_ipw_ids,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		1,
diff --git a/drivers/usb/serial/ir-usb.c b/drivers/usb/serial/ir-usb.c
index bf07905..19f329e 100644
--- a/drivers/usb/serial/ir-usb.c
+++ b/drivers/usb/serial/ir-usb.c
@@ -136,8 +136,9 @@ static struct usb_driver ir_driver = {
 static struct usb_serial_driver ir_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"ir-usb",
 	},
-	.name =			"IR Dongle",
+	.description =		"IR Dongle",
 	.id_table =		id_table,
 	.num_interrupt_in =	1,
 	.num_bulk_in =		1,
diff --git a/drivers/usb/serial/keyspan.h b/drivers/usb/serial/keyspan.h
index 124d46e..5cfc13b 100644
--- a/drivers/usb/serial/keyspan.h
+++ b/drivers/usb/serial/keyspan.h
@@ -573,9 +573,9 @@ static struct usb_device_id keyspan_4port_ids[] = {
 static struct usb_serial_driver keyspan_pre_device = {
 	.driver = {
 		.owner		= THIS_MODULE,
+		.name		= "keyspan_no_firm",
 	},
-	.name			= "Keyspan - (without firmware)",
-	.short_name		= "keyspan_no_firm",
+	.description		= "Keyspan - (without firmware)",
 	.id_table		= keyspan_pre_ids,
 	.num_interrupt_in	= NUM_DONT_CARE,
 	.num_bulk_in		= NUM_DONT_CARE,
@@ -587,9 +587,9 @@ static struct usb_serial_driver keyspan_pre_device = {
 static struct usb_serial_driver keyspan_1port_device = {
 	.driver = {
 		.owner		= THIS_MODULE,
+		.name		= "keyspan_1",
 	},
-	.name			= "Keyspan 1 port adapter",
-	.short_name		= "keyspan_1",
+	.description		= "Keyspan 1 port adapter",
 	.id_table		= keyspan_1port_ids,
 	.num_interrupt_in	= NUM_DONT_CARE,
 	.num_bulk_in		= NUM_DONT_CARE,
@@ -614,9 +614,9 @@ static struct usb_serial_driver keyspan_1port_device = {
 static struct usb_serial_driver keyspan_2port_device = {
 	.driver = {
 		.owner		= THIS_MODULE,
+		.name		= "keyspan_2",
 	},
-	.name			= "Keyspan 2 port adapter",
-	.short_name		= "keyspan_2",
+	.description		= "Keyspan 2 port adapter",
 	.id_table		= keyspan_2port_ids,
 	.num_interrupt_in	= NUM_DONT_CARE,
 	.num_bulk_in		= NUM_DONT_CARE,
@@ -641,9 +641,9 @@ static struct usb_serial_driver keyspan_2port_device = {
 static struct usb_serial_driver keyspan_4port_device = {
 	.driver = {
 		.owner		= THIS_MODULE,
+		.name		= "keyspan_4",
 	},
-	.name			= "Keyspan 4 port adapter",
-	.short_name		= "keyspan_4",
+	.description		= "Keyspan 4 port adapter",
 	.id_table		= keyspan_4port_ids,
 	.num_interrupt_in	= NUM_DONT_CARE,
 	.num_bulk_in		= 5,
diff --git a/drivers/usb/serial/keyspan_pda.c b/drivers/usb/serial/keyspan_pda.c
index 389b783..cd4f48b 100644
--- a/drivers/usb/serial/keyspan_pda.c
+++ b/drivers/usb/serial/keyspan_pda.c
@@ -786,9 +786,9 @@ static void keyspan_pda_shutdown (struct usb_serial *serial)
 static struct usb_serial_driver keyspan_pda_fake_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"keyspan_pda_pre",
 	},
-	.name =			"Keyspan PDA - (prerenumeration)",
-	.short_name =		"keyspan_pda_pre",
+	.description =		"Keyspan PDA - (prerenumeration)",
 	.id_table =		id_table_fake,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		NUM_DONT_CARE,
@@ -802,9 +802,9 @@ static struct usb_serial_driver keyspan_pda_fake_device = {
 static struct usb_serial_driver xircom_pgs_fake_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"xircom_no_firm",
 	},
-	.name =			"Xircom / Entregra PGS - (prerenumeration)",
-	.short_name =		"xircom_no_firm",
+	.description =		"Xircom / Entregra PGS - (prerenumeration)",
 	.id_table =		id_table_fake_xircom,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		NUM_DONT_CARE,
@@ -817,9 +817,9 @@ static struct usb_serial_driver xircom_pgs_fake_device = {
 static struct usb_serial_driver keyspan_pda_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"keyspan_pda",
 	},
-	.name =			"Keyspan PDA",
-	.short_name =		"keyspan_pda",
+	.description =		"Keyspan PDA",
 	.id_table =		id_table_std,
 	.num_interrupt_in =	1,
 	.num_bulk_in =		0,
diff --git a/drivers/usb/serial/kl5kusb105.c b/drivers/usb/serial/kl5kusb105.c
index 586108c..a8951c0 100644
--- a/drivers/usb/serial/kl5kusb105.c
+++ b/drivers/usb/serial/kl5kusb105.c
@@ -126,9 +126,9 @@ static struct usb_driver kl5kusb105d_driver = {
 static struct usb_serial_driver kl5kusb105d_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"kl5kusb105d",
 	},
-	.name =		     "KL5KUSB105D / PalmConnect",
-	.short_name =	     "kl5kusb105d",
+	.description =	     "KL5KUSB105D / PalmConnect",
 	.id_table =	     id_table,
 	.num_interrupt_in =  1,
 	.num_bulk_in =	     1,
diff --git a/drivers/usb/serial/kobil_sct.c b/drivers/usb/serial/kobil_sct.c
index a9578e0..9456dd9 100644
--- a/drivers/usb/serial/kobil_sct.c
+++ b/drivers/usb/serial/kobil_sct.c
@@ -108,8 +108,9 @@ static struct usb_driver kobil_driver = {
 static struct usb_serial_driver kobil_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"kobil",
 	},
-	.name =			"KOBIL USB smart card terminal",
+	.description =		"KOBIL USB smart card terminal",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		0,
diff --git a/drivers/usb/serial/mct_u232.c b/drivers/usb/serial/mct_u232.c
index 7dcf91c..ca5dbad 100644
--- a/drivers/usb/serial/mct_u232.c
+++ b/drivers/usb/serial/mct_u232.c
@@ -135,9 +135,9 @@ static struct usb_driver mct_u232_driver = {
 static struct usb_serial_driver mct_u232_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"mct_u232",
 	},
-	.name =		     "MCT U232",
-	.short_name =	     "mct_u232",
+	.description =	     "MCT U232",
 	.id_table =	     id_table_combined,
 	.num_interrupt_in =  2,
 	.num_bulk_in =	     0,
diff --git a/drivers/usb/serial/omninet.c b/drivers/usb/serial/omninet.c
index f6327cc1..3caf970 100644
--- a/drivers/usb/serial/omninet.c
+++ b/drivers/usb/serial/omninet.c
@@ -91,9 +91,9 @@ static struct usb_driver omninet_driver = {
 static struct usb_serial_driver zyxel_omninet_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"omninet",
 	},
-	.name =			"ZyXEL - omni.net lcd plus usb",
-	.short_name =		"omninet",
+	.description =		"ZyXEL - omni.net lcd plus usb",
 	.id_table =		id_table,
 	.num_interrupt_in =	1,
 	.num_bulk_in =		1,
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index a2b5adf..7716000 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -108,9 +108,9 @@ static struct usb_driver option_driver = {
 static struct usb_serial_driver option_3port_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"option",
 	},
-	.name              = "Option 3G data card",
-	.short_name        = "option",
+	.description       = "Option 3G data card",
 	.id_table          = option_ids,
 	.num_interrupt_in  = NUM_DONT_CARE,
 	.num_bulk_in       = NUM_DONT_CARE,
diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index 29719ce..f8f4e93 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -157,8 +157,8 @@ static unsigned int pl2303_buf_get(struct pl2303_buf *pb, char *buf,
 static struct usb_serial_driver pl2303_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"pl2303",
 	},
-	.name =			"PL-2303",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		1,
diff --git a/drivers/usb/serial/safe_serial.c b/drivers/usb/serial/safe_serial.c
index 42a86ab..c22bdc0 100644
--- a/drivers/usb/serial/safe_serial.c
+++ b/drivers/usb/serial/safe_serial.c
@@ -400,8 +400,8 @@ static int safe_startup (struct usb_serial *serial)
 static struct usb_serial_driver safe_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"safe_serial",
 	},
-	.name =			"Safe",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		NUM_DONT_CARE,
diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index eab8a6d..205dbf7 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -257,9 +257,10 @@ static struct usb_driver ti_usb_driver = {
 
 static struct usb_serial_driver ti_1port_device = {
 	.driver = {
-		.owner =	THIS_MODULE,
+		.owner		= THIS_MODULE,
+		.name		= "ti_usb_3410_5052_1",
 	},
-	.name			= "TI USB 3410 1 port adapter",
+	.description		= "TI USB 3410 1 port adapter",
 	.id_table		= ti_id_table_3410,
 	.num_interrupt_in	= 1,
 	.num_bulk_in		= 1,
@@ -286,9 +287,10 @@ static struct usb_serial_driver ti_1port_device = {
 
 static struct usb_serial_driver ti_2port_device = {
 	.driver = {
-		.owner =	THIS_MODULE,
+		.owner		= THIS_MODULE,
+		.name		= "ti_usb_3410_5052_2",
 	},
-	.name			= "TI USB 5052 2 port adapter",
+	.description		= "TI USB 5052 2 port adapter",
 	.id_table		= ti_id_table_5052,
 	.num_interrupt_in	= 1,
 	.num_bulk_in		= 2,
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index fde09fb..13f6592 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -122,7 +122,7 @@ static void destroy_serial(struct kref *kref)
 
 	serial = to_usb_serial(kref);
 
-	dbg ("%s - %s", __FUNCTION__, serial->type->name);
+	dbg("%s - %s", __FUNCTION__, serial->type->description);
 
 	serial->type->shutdown(serial);
 
@@ -415,7 +415,7 @@ static int serial_read_proc (char *page, char **start, off_t off, int count, int
 		length += sprintf (page+length, "%d:", i);
 		if (serial->type->driver.owner)
 			length += sprintf (page+length, " module:%s", module_name(serial->type->driver.owner));
-		length += sprintf (page+length, " name:\"%s\"", serial->type->name);
+		length += sprintf (page+length, " name:\"%s\"", serial->type->description);
 		length += sprintf (page+length, " vendor:%04x product:%04x", 
 				   le16_to_cpu(serial->dev->descriptor.idVendor), 
 				   le16_to_cpu(serial->dev->descriptor.idProduct));
@@ -687,7 +687,7 @@ int usb_serial_probe(struct usb_interface *interface,
 #endif
 
 	/* found all that we need */
-	dev_info(&interface->dev, "%s converter detected\n", type->name);
+	dev_info(&interface->dev, "%s converter detected\n", type->description);
 
 #ifdef CONFIG_USB_SERIAL_GENERIC
 	if (type == &usb_serial_generic_device) {
@@ -1088,16 +1088,19 @@ int usb_serial_register(struct usb_serial_driver *driver)
 
 	fixup_generic(driver);
 
+	if (!driver->description)
+		driver->description = driver->driver.name;
+
 	/* Add this device to our list of devices */
 	list_add(&driver->driver_list, &usb_serial_driver_list);
 
 	retval = usb_serial_bus_register(driver);
 	if (retval) {
-		err("problem %d when registering driver %s", retval, driver->name);
+		err("problem %d when registering driver %s", retval, driver->description);
 		list_del(&driver->driver_list);
 	}
 	else
-		info("USB Serial support registered for %s", driver->name);
+		info("USB Serial support registered for %s", driver->description);
 
 	return retval;
 }
@@ -1105,7 +1108,7 @@ int usb_serial_register(struct usb_serial_driver *driver)
 
 void usb_serial_deregister(struct usb_serial_driver *device)
 {
-	info("USB Serial deregistering driver %s", device->name);
+	info("USB Serial deregistering driver %s", device->description);
 	list_del(&device->driver_list);
 	usb_serial_bus_deregister(device);
 }
diff --git a/drivers/usb/serial/usb-serial.h b/drivers/usb/serial/usb-serial.h
index 1cedc19..238a5a8 100644
--- a/drivers/usb/serial/usb-serial.h
+++ b/drivers/usb/serial/usb-serial.h
@@ -149,11 +149,8 @@ static inline void usb_set_serial_data (struct usb_serial *serial, void *data)
 
 /**
  * usb_serial_driver - describes a usb serial driver
- * @name: pointer to a string that describes this driver.  This string used
+ * @description: pointer to a string that describes this driver.  This string used
  *	in the syslog messages when a device is inserted or removed.
- * @short_name: a pointer to a string that describes this driver in
- *	KOBJ_NAME_LEN characters or less.  This is used for the sysfs interface
- *	to describe the driver.
  * @id_table: pointer to a list of usb_device_id structures that define all
  *	of the devices this structure can support.
  * @num_interrupt_in: the number of interrupt in endpoints this device will
@@ -187,11 +184,12 @@ static inline void usb_set_serial_data (struct usb_serial *serial, void *data)
  * called, the generic serial function will be used instead.
  *
  * The driver.owner field should be set to the module owner of this driver.
- *
+ * The driver.name field should be set to the name of this driver (remember
+ * it will show up in sysfs, so it needs to be short and to the point.
+ * Useing the module name is a good idea.)
  */
 struct usb_serial_driver {
-	char	*name;
-	char	*short_name;
+	const char *description;
 	const struct usb_device_id *id_table;
 	char	num_interrupt_in;
 	char	num_interrupt_out;
diff --git a/drivers/usb/serial/visor.c b/drivers/usb/serial/visor.c
index 39ad0ca..baa2acb 100644
--- a/drivers/usb/serial/visor.c
+++ b/drivers/usb/serial/visor.c
@@ -185,9 +185,9 @@ static struct usb_driver visor_driver = {
 static struct usb_serial_driver handspring_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"visor",
 	},
-	.name =			"Handspring Visor / Palm OS",
-	.short_name =		"visor",
+	.description =		"Handspring Visor / Palm OS",
 	.id_table =		id_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		2,
@@ -215,9 +215,9 @@ static struct usb_serial_driver handspring_device = {
 static struct usb_serial_driver clie_5_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"clie_5",
 	},
-	.name =			"Sony Clie 5.0",
-	.short_name =		"clie_5",
+	.description =		"Sony Clie 5.0",
 	.id_table =		clie_id_5_table,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		2,
@@ -245,9 +245,9 @@ static struct usb_serial_driver clie_5_device = {
 static struct usb_serial_driver clie_3_5_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"clie_3.5",
 	},
-	.name =			"Sony Clie 3.5",
-	.short_name =		"clie_3.5",
+	.description =		"Sony Clie 3.5",
 	.id_table =		clie_id_3_5_table,
 	.num_interrupt_in =	0,
 	.num_bulk_in =		1,
@@ -659,7 +659,7 @@ static int palm_os_3_probe (struct usb_serial *serial, const struct usb_device_i
 					break;
 			}
 			dev_info(dev, "%s: port %d, is for %s use\n",
-				serial->type->name,
+				serial->type->description,
 				connection_info->connections[i].port, string);
 		}
 	}
@@ -668,11 +668,11 @@ static int palm_os_3_probe (struct usb_serial *serial, const struct usb_device_i
 	*/
 	if (num_ports == 0 || num_ports > 2) {
 		dev_warn (dev, "%s: No valid connect info available\n",
-			serial->type->name);
+			serial->type->description);
 		num_ports = 2;
 	}
   
-	dev_info(dev, "%s: Number of ports: %d\n", serial->type->name,
+	dev_info(dev, "%s: Number of ports: %d\n", serial->type->description,
 		num_ports);
 
 	/*
diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c
index fb95a34..18c3183 100644
--- a/drivers/usb/serial/whiteheat.c
+++ b/drivers/usb/serial/whiteheat.c
@@ -159,9 +159,9 @@ static void whiteheat_write_callback	(struct urb *urb, struct pt_regs *regs);
 static struct usb_serial_driver whiteheat_fake_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"whiteheatnofirm",
 	},
-	.name =			"Connect Tech - WhiteHEAT - (prerenumeration)",
-	.short_name =		"whiteheatnofirm",
+	.description =		"Connect Tech - WhiteHEAT - (prerenumeration)",
 	.id_table =		id_table_prerenumeration,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		NUM_DONT_CARE,
@@ -174,9 +174,9 @@ static struct usb_serial_driver whiteheat_fake_device = {
 static struct usb_serial_driver whiteheat_device = {
 	.driver = {
 		.owner =	THIS_MODULE,
+		.name =		"whiteheat",
 	},
-	.name =			"Connect Tech - WhiteHEAT",
-	.short_name =		"whiteheat",
+	.description =		"Connect Tech - WhiteHEAT",
 	.id_table =		id_table_std,
 	.num_interrupt_in =	NUM_DONT_CARE,
 	.num_bulk_in =		NUM_DONT_CARE,
@@ -386,10 +386,10 @@ static int whiteheat_attach (struct usb_serial *serial)
 	usb_clear_halt(serial->dev, pipe);
 	ret = usb_bulk_msg (serial->dev, pipe, command, 2, &alen, COMMAND_TIMEOUT_MS);
 	if (ret) {
-		err("%s: Couldn't send command [%d]", serial->type->name, ret);
+		err("%s: Couldn't send command [%d]", serial->type->description, ret);
 		goto no_firmware;
 	} else if (alen != sizeof(command)) {
-		err("%s: Send command incomplete [%d]", serial->type->name, alen);
+		err("%s: Send command incomplete [%d]", serial->type->description, alen);
 		goto no_firmware;
 	}
 
@@ -398,19 +398,19 @@ static int whiteheat_attach (struct usb_serial *serial)
 	usb_clear_halt(serial->dev, pipe);
 	ret = usb_bulk_msg (serial->dev, pipe, result, sizeof(*hw_info) + 1, &alen, COMMAND_TIMEOUT_MS);
 	if (ret) {
-		err("%s: Couldn't get results [%d]", serial->type->name, ret);
+		err("%s: Couldn't get results [%d]", serial->type->description, ret);
 		goto no_firmware;
 	} else if (alen != sizeof(result)) {
-		err("%s: Get results incomplete [%d]", serial->type->name, alen);
+		err("%s: Get results incomplete [%d]", serial->type->description, alen);
 		goto no_firmware;
 	} else if (result[0] != command[0]) {
-		err("%s: Command failed [%d]", serial->type->name, result[0]);
+		err("%s: Command failed [%d]", serial->type->description, result[0]);
 		goto no_firmware;
 	}
 
 	hw_info = (struct whiteheat_hw_info *)&result[1];
 
-	info("%s: Driver %s: Firmware v%d.%02d", serial->type->name,
+	info("%s: Driver %s: Firmware v%d.%02d", serial->type->description,
 	     DRIVER_VERSION, hw_info->sw_major_rev, hw_info->sw_minor_rev);
 
 	for (i = 0; i < serial->num_ports; i++) {
@@ -418,7 +418,7 @@ static int whiteheat_attach (struct usb_serial *serial)
 
 		info = (struct whiteheat_private *)kmalloc(sizeof(struct whiteheat_private), GFP_KERNEL);
 		if (info == NULL) {
-			err("%s: Out of memory for port structures\n", serial->type->name);
+			err("%s: Out of memory for port structures\n", serial->type->description);
 			goto no_private;
 		}
 
@@ -488,7 +488,7 @@ static int whiteheat_attach (struct usb_serial *serial)
 
 	command_info = (struct whiteheat_command_private *)kmalloc(sizeof(struct whiteheat_command_private), GFP_KERNEL);
 	if (command_info == NULL) {
-		err("%s: Out of memory for port structures\n", serial->type->name);
+		err("%s: Out of memory for port structures\n", serial->type->description);
 		goto no_command_private;
 	}
 
@@ -505,9 +505,9 @@ static int whiteheat_attach (struct usb_serial *serial)
 
 no_firmware:
 	/* Firmware likely not running */
-	err("%s: Unable to retrieve firmware version, try replugging\n", serial->type->name);
-	err("%s: If the firmware is not running (status led not blinking)\n", serial->type->name);
-	err("%s: please contact support@connecttech.com\n", serial->type->name);
+	err("%s: Unable to retrieve firmware version, try replugging\n", serial->type->description);
+	err("%s: If the firmware is not running (status led not blinking)\n", serial->type->description);
+	err("%s: please contact support@connecttech.com\n", serial->type->description);
 	return -ENODEV;
 
 no_command_private:
-- 
cgit v1.1


From 17a882fc0c91477b2582a6dfd4ca93ae7eb58cd3 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB Serial: remove driver version from a few drivers

These numbers are pointless, as they have not been changed in _years_,
so we should just remove them to stop pretending there is an actual
"version number" for these drivers.

This should also help reduce confusion when people try to ask for
support of a specific driver version, as there has been no way to tell
what they are talking about.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/pl2303.c     | 4 +---
 drivers/usb/serial/usb-serial.c | 6 ++----
 drivers/usb/serial/visor.c      | 3 +--
 3 files changed, 4 insertions(+), 9 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index f8f4e93..165c119 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -34,7 +34,6 @@
 /*
  * Version Information
  */
-#define DRIVER_VERSION "v0.12"
 #define DRIVER_DESC "Prolific PL2303 USB to serial adaptor driver"
 
 static int debug;
@@ -1176,7 +1175,7 @@ static int __init pl2303_init (void)
 	retval = usb_register(&pl2303_driver);
 	if (retval)
 		goto failed_usb_register;
-	info(DRIVER_DESC " " DRIVER_VERSION);
+	info(DRIVER_DESC);
 	return 0;
 failed_usb_register:
 	usb_serial_deregister(&pl2303_device);
@@ -1196,7 +1195,6 @@ module_init(pl2303_init);
 module_exit(pl2303_exit);
 
 MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_VERSION(DRIVER_VERSION);
 MODULE_LICENSE("GPL");
 
 module_param(debug, bool, S_IRUGO | S_IWUSR);
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index 13f6592..0c4881d 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -37,7 +37,6 @@
 /*
  * Version Information
  */
-#define DRIVER_VERSION "v2.0"
 #define DRIVER_AUTHOR "Greg Kroah-Hartman, greg@kroah.com, http://www.kroah.com/linux/"
 #define DRIVER_DESC "USB Serial Driver core"
 
@@ -406,7 +405,7 @@ static int serial_read_proc (char *page, char **start, off_t off, int count, int
 	char tmp[40];
 
 	dbg("%s", __FUNCTION__);
-	length += sprintf (page, "usbserinfo:1.0 driver:%s\n", DRIVER_VERSION);
+	length += sprintf (page, "usbserinfo:1.0 driver:2.0\n");
 	for (i = 0; i < SERIAL_TTY_MINORS && length < PAGE_SIZE; ++i) {
 		serial = usb_serial_get_by_index(i);
 		if (serial == NULL)
@@ -1025,7 +1024,7 @@ static int __init usb_serial_init(void)
 		goto exit_generic;
 	}
 
-	info(DRIVER_DESC " " DRIVER_VERSION);
+	info(DRIVER_DESC);
 
 	return result;
 
@@ -1127,7 +1126,6 @@ EXPORT_SYMBOL_GPL(usb_serial_port_softint);
 /* Module information */
 MODULE_AUTHOR( DRIVER_AUTHOR );
 MODULE_DESCRIPTION( DRIVER_DESC );
-MODULE_VERSION( DRIVER_VERSION );
 MODULE_LICENSE("GPL");
 
 module_param(debug, bool, S_IRUGO | S_IWUSR);
diff --git a/drivers/usb/serial/visor.c b/drivers/usb/serial/visor.c
index baa2acb..a473c1c 100644
--- a/drivers/usb/serial/visor.c
+++ b/drivers/usb/serial/visor.c
@@ -32,7 +32,6 @@
 /*
  * Version Information
  */
-#define DRIVER_VERSION "v2.1"
 #define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com>"
 #define DRIVER_DESC "USB HandSpring Visor / Palm OS driver"
 
@@ -1002,7 +1001,7 @@ static int __init visor_init (void)
 	retval = usb_register(&visor_driver);
 	if (retval) 
 		goto failed_usb_register;
-	info(DRIVER_DESC " " DRIVER_VERSION);
+	info(DRIVER_DESC);
 
 	return 0;
 failed_usb_register:
-- 
cgit v1.1


From 7521803dcc0137668bb30483383092a647671d8b Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: always export interface information for modalias

This fixes a problem with some cdc acm devices that were not getting
automatically loaded as the module alias was not being reported
properly.

This check was for back in the days when we only reported hotplug events
for the main usb device, not the interfaces.  We should always give the
interface information for MODALIAS/modalias as it can be needed.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/sysfs.c | 35 +++++++++++----------------
 drivers/usb/core/usb.c   | 63 ++++++++++++++++++------------------------------
 2 files changed, 37 insertions(+), 61 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/sysfs.c b/drivers/usb/core/sysfs.c
index eae413b..4bdbc9d 100644
--- a/drivers/usb/core/sysfs.c
+++ b/drivers/usb/core/sysfs.c
@@ -462,30 +462,23 @@ static ssize_t show_modalias(struct device *dev, struct device_attribute *attr,
 {
 	struct usb_interface *intf;
 	struct usb_device *udev;
-	int len;
+	struct usb_host_interface *alt;
 
 	intf = to_usb_interface(dev);
 	udev = interface_to_usbdev(intf);
-
-	len = sprintf(buf, "usb:v%04Xp%04Xd%04Xdc%02Xdsc%02Xdp%02Xic",
-			       le16_to_cpu(udev->descriptor.idVendor),
-			       le16_to_cpu(udev->descriptor.idProduct),
-			       le16_to_cpu(udev->descriptor.bcdDevice),
-			       udev->descriptor.bDeviceClass,
-			       udev->descriptor.bDeviceSubClass,
-			       udev->descriptor.bDeviceProtocol);
-	buf += len;
-
-	if (udev->descriptor.bDeviceClass == 0) {
-		struct usb_host_interface *alt = intf->cur_altsetting;
-
-		return len + sprintf(buf, "%02Xisc%02Xip%02X\n",
-			       alt->desc.bInterfaceClass,
-			       alt->desc.bInterfaceSubClass,
-			       alt->desc.bInterfaceProtocol);
- 	} else {
-		return len + sprintf(buf, "*isc*ip*\n");
-	}
+	alt = intf->cur_altsetting;
+
+	return sprintf(buf, "usb:v%04Xp%04Xd%04Xdc%02Xdsc%02Xdp%02X"
+			"ic%02Xisc%02Xip%02X\n",
+			le16_to_cpu(udev->descriptor.idVendor),
+			le16_to_cpu(udev->descriptor.idProduct),
+			le16_to_cpu(udev->descriptor.bcdDevice),
+			udev->descriptor.bDeviceClass,
+			udev->descriptor.bDeviceSubClass,
+			udev->descriptor.bDeviceProtocol,
+			alt->desc.bInterfaceClass,
+			alt->desc.bInterfaceSubClass,
+			alt->desc.bInterfaceProtocol);
 }
 static DEVICE_ATTR(modalias, S_IRUGO, show_modalias, NULL);
 
diff --git a/drivers/usb/core/usb.c b/drivers/usb/core/usb.c
index 2493e7d..4eca490 100644
--- a/drivers/usb/core/usb.c
+++ b/drivers/usb/core/usb.c
@@ -569,6 +569,7 @@ static int usb_hotplug (struct device *dev, char **envp, int num_envp,
 {
 	struct usb_interface *intf;
 	struct usb_device *usb_dev;
+	struct usb_host_interface *alt;
 	int i = 0;
 	int length = 0;
 
@@ -585,7 +586,8 @@ static int usb_hotplug (struct device *dev, char **envp, int num_envp,
 
 	intf = to_usb_interface(dev);
 	usb_dev = interface_to_usbdev (intf);
-	
+	alt = intf->cur_altsetting;
+
 	if (usb_dev->devnum < 0) {
 		pr_debug ("usb %s: already deleted?\n", dev->bus_id);
 		return -ENODEV;
@@ -627,46 +629,27 @@ static int usb_hotplug (struct device *dev, char **envp, int num_envp,
 				usb_dev->descriptor.bDeviceProtocol))
 		return -ENOMEM;
 
-	if (usb_dev->descriptor.bDeviceClass == 0) {
-		struct usb_host_interface *alt = intf->cur_altsetting;
+	if (add_hotplug_env_var(envp, num_envp, &i,
+				buffer, buffer_size, &length,
+				"INTERFACE=%d/%d/%d",
+				alt->desc.bInterfaceClass,
+				alt->desc.bInterfaceSubClass,
+				alt->desc.bInterfaceProtocol))
+		return -ENOMEM;
 
-		/* 2.4 only exposed interface zero.  in 2.5, hotplug
-		 * agents are called for all interfaces, and can use
-		 * $DEVPATH/bInterfaceNumber if necessary.
-		 */
-		if (add_hotplug_env_var(envp, num_envp, &i,
-					buffer, buffer_size, &length,
-					"INTERFACE=%d/%d/%d",
-					alt->desc.bInterfaceClass,
-					alt->desc.bInterfaceSubClass,
-					alt->desc.bInterfaceProtocol))
-			return -ENOMEM;
-
-		if (add_hotplug_env_var(envp, num_envp, &i,
-					buffer, buffer_size, &length,
-					"MODALIAS=usb:v%04Xp%04Xd%04Xdc%02Xdsc%02Xdp%02Xic%02Xisc%02Xip%02X",
-					le16_to_cpu(usb_dev->descriptor.idVendor),
-					le16_to_cpu(usb_dev->descriptor.idProduct),
-					le16_to_cpu(usb_dev->descriptor.bcdDevice),
-					usb_dev->descriptor.bDeviceClass,
-					usb_dev->descriptor.bDeviceSubClass,
-					usb_dev->descriptor.bDeviceProtocol,
-					alt->desc.bInterfaceClass,
-					alt->desc.bInterfaceSubClass,
-					alt->desc.bInterfaceProtocol))
-			return -ENOMEM;
- 	} else {
-		if (add_hotplug_env_var(envp, num_envp, &i,
-					buffer, buffer_size, &length,
-					"MODALIAS=usb:v%04Xp%04Xd%04Xdc%02Xdsc%02Xdp%02Xic*isc*ip*",
-					le16_to_cpu(usb_dev->descriptor.idVendor),
-					le16_to_cpu(usb_dev->descriptor.idProduct),
-					le16_to_cpu(usb_dev->descriptor.bcdDevice),
-					usb_dev->descriptor.bDeviceClass,
-					usb_dev->descriptor.bDeviceSubClass,
-					usb_dev->descriptor.bDeviceProtocol))
-			return -ENOMEM;
-	}
+	if (add_hotplug_env_var(envp, num_envp, &i,
+				buffer, buffer_size, &length,
+				"MODALIAS=usb:v%04Xp%04Xd%04Xdc%02Xdsc%02Xdp%02Xic%02Xisc%02Xip%02X",
+				le16_to_cpu(usb_dev->descriptor.idVendor),
+				le16_to_cpu(usb_dev->descriptor.idProduct),
+				le16_to_cpu(usb_dev->descriptor.bcdDevice),
+				usb_dev->descriptor.bDeviceClass,
+				usb_dev->descriptor.bDeviceSubClass,
+				usb_dev->descriptor.bDeviceProtocol,
+				alt->desc.bInterfaceClass,
+				alt->desc.bInterfaceSubClass,
+				alt->desc.bInterfaceProtocol))
+		return -ENOMEM;
 
 	envp[i] = NULL;
 
-- 
cgit v1.1


From dcab4eaf77ccd8779c715da3c5db0a82874fa645 Mon Sep 17 00:00:00 2001
From: Simeon Simeonov <simeonov_2000@yahoo.com>
Date: Wed, 19 Oct 2005 11:32:14 -0400
Subject: [PATCH] USB: storage patch for LEICA camera

On Tue, 18 Oct 2005, Simeon Simeonov wrote:
> Attached is a patch that solves mounting problems for
> LEICA D-LUX camera with FC4 2.6.13 kernel.
>
> Let me know if you have some questions.

Looks okay to me.  Given that the previous entry uses the full 0000 -
9999 range, I guess this one can also.  The vendor name is a little odd
(it will give us three different vendor names all in entries with the
same vendor ID) but that doesn't really matter either.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/storage/unusual_devs.h | 7 +++++++
 1 file changed, 7 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index a117018..d0f6a7e 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -251,6 +251,13 @@ UNUSUAL_DEV(  0x04da, 0x2372, 0x0000, 0x9999,
 		US_SC_DEVICE, US_PR_DEVICE, NULL,
 		US_FL_FIX_CAPACITY | US_FL_NOT_LOCKABLE ),
 
+/* Reported by Simeon Simeonov <simeonov_2000@yahoo.com> */
+UNUSUAL_DEV(  0x04da, 0x2373, 0x0000, 0x9999,
+		"LEICA",
+		"D-LUX Camera",
+		US_SC_DEVICE, US_PR_DEVICE, NULL,
+		US_FL_FIX_CAPACITY | US_FL_NOT_LOCKABLE ),
+
 /* Most of the following entries were developed with the help of
  * Shuttle/SCM directly.
  */
-- 
cgit v1.1


From 61eded6e06a1f4bdbf707b69da904ba9f3eb2f0a Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Mon, 24 Oct 2005 22:37:20 +0200
Subject: [PATCH] USB: microtek patch to use kzalloc

here is another one to use kzalloc. Please apply.

Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/image/microtek.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/image/microtek.c b/drivers/usb/image/microtek.c
index c84e148..c89d076 100644
--- a/drivers/usb/image/microtek.c
+++ b/drivers/usb/image/microtek.c
@@ -773,11 +773,10 @@ static int mts_usb_probe(struct usb_interface *intf,
 	}
 	
 	
-	new_desc = kmalloc(sizeof(struct mts_desc), GFP_KERNEL);
+	new_desc = kzalloc(sizeof(struct mts_desc), GFP_KERNEL);
 	if (!new_desc)
 		goto out;
 
-	memset(new_desc, 0, sizeof(*new_desc));
 	new_desc->urb = usb_alloc_urb(0, GFP_KERNEL);
 	if (!new_desc->urb)
 		goto out_kfree;
-- 
cgit v1.1


From f2d45cd976682a3566c8cf30cefe91eb43ab6005 Mon Sep 17 00:00:00 2001
From: Guillaume GOURAT / <guillaume.gourat@nexvision.fr>
Date: Fri, 21 Oct 2005 14:01:35 +0200
Subject: [PATCH] USB: Kaweth.c udelay patch

On some arch (like arm) udelay cannot be called with value greater that
2000.

Signed-off-by: Guillaume GOURAT / guillaume.gourat@nexvision.fr
Signed-off-by: Oliver Neukum <oliver@neukum.name>
---
 drivers/usb/net/kaweth.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers')

diff --git a/drivers/usb/net/kaweth.c b/drivers/usb/net/kaweth.c
index c82655d..6bef1be 100644
--- a/drivers/usb/net/kaweth.c
+++ b/drivers/usb/net/kaweth.c
@@ -469,7 +469,7 @@ static int kaweth_reset(struct kaweth_device *kaweth)
 				0,
 				KAWETH_CONTROL_TIMEOUT);
 
-	udelay(10000);
+	mdelay(10);
 
 	kaweth_dbg("kaweth_reset() returns %d.",result);
 
-- 
cgit v1.1


From eb3c5ed8617d0aa67648cb7d1a486d14099129f2 Mon Sep 17 00:00:00 2001
From: David Eriksson <twogood@users.sourceforge.net>
Date: Tue, 18 Oct 2005 20:12:24 +0200
Subject: [PATCH] USB: Improving the set of vendor/product IDs in the ipaq
 driver

This is a patch improving the set of vendor/product IDs used in the
"ipaq" USB serial device driver. The patch size is because I sorted the
ids this time, forgot about that last time.

Changes:

- Added vendor/product identifiers for Psion Teklogix devices
- Restored Microsoft's identifier pair 045e/00ce
- Sorted list of vendor/product identifiers

Signed-off-by: David Eriksson <twogood@users.sourceforge.net>
Signed-off-by: Ganesh Varadarajan <ganesh@veritas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/ipaq.c | 238 +++++++++++++++++++++++-----------------------
 1 file changed, 121 insertions(+), 117 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/serial/ipaq.c b/drivers/usb/serial/ipaq.c
index 1abaebe..d5d0664 100644
--- a/drivers/usb/serial/ipaq.c
+++ b/drivers/usb/serial/ipaq.c
@@ -92,24 +92,7 @@ static void ipaq_destroy_lists(struct usb_serial_port *port);
 static struct usb_device_id ipaq_id_table [] = {
 	/* The first entry is a placeholder for the insmod-specified device */
 	{ USB_DEVICE(0x049F, 0x0003) },
-	{ USB_DEVICE(0x1690, 0x0601) }, /* Askey USB Sync */
-	{ USB_DEVICE(0x0960, 0x0065) }, /* BCOM USB Sync 0065 */
-	{ USB_DEVICE(0x0960, 0x0066) }, /* BCOM USB Sync 0066 */
-	{ USB_DEVICE(0x0960, 0x0067) }, /* BCOM USB Sync 0067 */
-	{ USB_DEVICE(0x07CF, 0x2001) }, /* CASIO USB Sync 2001 */
-	{ USB_DEVICE(0x07CF, 0x2002) }, /* CASIO USB Sync 2002 */
-	{ USB_DEVICE(0x07CF, 0x2003) }, /* CASIO USB Sync 2003 */
-	{ USB_DEVICE(0x049F, 0x0003) }, /* Compaq iPAQ USB Sync */
-	{ USB_DEVICE(0x049F, 0x0032) }, /* Compaq iPAQ USB Sync */
-	{ USB_DEVICE(0x413C, 0x4001) }, /* Dell Axim USB Sync */
-	{ USB_DEVICE(0x413C, 0x4002) }, /* Dell Axim USB Sync */
-	{ USB_DEVICE(0x413C, 0x4003) }, /* Dell Axim USB Sync */
-	{ USB_DEVICE(0x413C, 0x4004) }, /* Dell Axim USB Sync */
-	{ USB_DEVICE(0x413C, 0x4005) }, /* Dell Axim USB Sync */
-	{ USB_DEVICE(0x413C, 0x4006) }, /* Dell Axim USB Sync */
-	{ USB_DEVICE(0x413C, 0x4007) }, /* Dell Axim USB Sync */
-	{ USB_DEVICE(0x413C, 0x4008) }, /* Dell Axim USB Sync */
-	{ USB_DEVICE(0x413C, 0x4009) }, /* Dell Axim USB Sync */
+	{ USB_DEVICE(0x0104, 0x00BE) }, /* Socket USB Sync */
 	{ USB_DEVICE(0x03F0, 0x1016) }, /* HP USB Sync */
 	{ USB_DEVICE(0x03F0, 0x1116) }, /* HP USB Sync 1611 */
 	{ USB_DEVICE(0x03F0, 0x1216) }, /* HP USB Sync 1612 */
@@ -125,7 +108,13 @@ static struct usb_device_id ipaq_id_table [] = {
 	{ USB_DEVICE(0x03F0, 0x5016) }, /* HP USB Sync 1650 */
 	{ USB_DEVICE(0x03F0, 0x5116) }, /* HP USB Sync 1651 */
 	{ USB_DEVICE(0x03F0, 0x5216) }, /* HP USB Sync 1652 */
-	{ USB_DEVICE(0x094B, 0x0001) }, /* Linkup Systems USB Sync */
+	{ USB_DEVICE(0x0409, 0x00D5) }, /* NEC USB Sync */
+	{ USB_DEVICE(0x0409, 0x00D6) }, /* NEC USB Sync */
+	{ USB_DEVICE(0x0409, 0x00D7) }, /* NEC USB Sync */
+	{ USB_DEVICE(0x0409, 0x8024) }, /* NEC USB Sync */
+	{ USB_DEVICE(0x0409, 0x8025) }, /* NEC USB Sync */
+	{ USB_DEVICE(0x043E, 0x9C01) }, /* LGE USB Sync */
+	{ USB_DEVICE(0x045E, 0x00CE) }, /* Microsoft USB Sync */
 	{ USB_DEVICE(0x045E, 0x0400) }, /* Windows Powered Pocket PC 2002 */
 	{ USB_DEVICE(0x045E, 0x0401) }, /* Windows Powered Pocket PC 2002 */
 	{ USB_DEVICE(0x045E, 0x0402) }, /* Windows Powered Pocket PC 2002 */
@@ -251,17 +240,81 @@ static struct usb_device_id ipaq_id_table [] = {
 	{ USB_DEVICE(0x045E, 0x04E8) }, /* Windows Powered Smartphone 2003 */
 	{ USB_DEVICE(0x045E, 0x04E9) }, /* Windows Powered Smartphone 2003 */
 	{ USB_DEVICE(0x045E, 0x04EA) }, /* Windows Powered Smartphone 2003 */
-	{ USB_DEVICE(0x0961, 0x0010) }, /* Portatec USB Sync */
-	{ USB_DEVICE(0x5E04, 0xCE00) }, /* SAGEM Wireless Assistant */
-	{ USB_DEVICE(0x0104, 0x00BE) }, /* Socket USB Sync */
+	{ USB_DEVICE(0x049F, 0x0003) }, /* Compaq iPAQ USB Sync */
+	{ USB_DEVICE(0x049F, 0x0032) }, /* Compaq iPAQ USB Sync */
+	{ USB_DEVICE(0x04A4, 0x0014) }, /* Hitachi USB Sync */
+	{ USB_DEVICE(0x04AD, 0x0301) }, /* USB Sync 0301 */
+	{ USB_DEVICE(0x04AD, 0x0302) }, /* USB Sync 0302 */
+	{ USB_DEVICE(0x04AD, 0x0303) }, /* USB Sync 0303 */
+	{ USB_DEVICE(0x04C5, 0x1058) }, /* FUJITSU USB Sync */
+	{ USB_DEVICE(0x04C5, 0x1079) }, /* FUJITSU USB Sync */
+	{ USB_DEVICE(0x04DA, 0x2500) }, /* Panasonic USB Sync */
+	{ USB_DEVICE(0x04E8, 0x5F00) }, /* Samsung NEXiO USB Sync */
+	{ USB_DEVICE(0x04E8, 0x5F01) }, /* Samsung NEXiO USB Sync */
+	{ USB_DEVICE(0x04E8, 0x5F02) }, /* Samsung NEXiO USB Sync */
+	{ USB_DEVICE(0x04E8, 0x5F03) }, /* Samsung NEXiO USB Sync */
+	{ USB_DEVICE(0x04E8, 0x5F04) }, /* Samsung NEXiO USB Sync */
+	{ USB_DEVICE(0x04E8, 0x6611) }, /* Samsung MITs USB Sync */
+	{ USB_DEVICE(0x04E8, 0x6613) }, /* Samsung MITs USB Sync */
+	{ USB_DEVICE(0x04E8, 0x6615) }, /* Samsung MITs USB Sync */
+	{ USB_DEVICE(0x04E8, 0x6617) }, /* Samsung MITs USB Sync */
+	{ USB_DEVICE(0x04E8, 0x6619) }, /* Samsung MITs USB Sync */
+	{ USB_DEVICE(0x04E8, 0x661B) }, /* Samsung MITs USB Sync */
+	{ USB_DEVICE(0x04E8, 0x662E) }, /* Samsung MITs USB Sync */
+	{ USB_DEVICE(0x04E8, 0x6630) }, /* Samsung MITs USB Sync */
+	{ USB_DEVICE(0x04E8, 0x6632) }, /* Samsung MITs USB Sync */
+	{ USB_DEVICE(0x04f1, 0x3011) }, /* JVC USB Sync */
+	{ USB_DEVICE(0x04F1, 0x3012) }, /* JVC USB Sync */
+	{ USB_DEVICE(0x0502, 0x1631) }, /* c10 Series */
+	{ USB_DEVICE(0x0502, 0x1632) }, /* c20 Series */
+	{ USB_DEVICE(0x0502, 0x16E1) }, /* Acer n10 Handheld USB Sync */
+	{ USB_DEVICE(0x0502, 0x16E2) }, /* Acer n20 Handheld USB Sync */
+	{ USB_DEVICE(0x0502, 0x16E3) }, /* Acer n30 Handheld USB Sync */
+	{ USB_DEVICE(0x0536, 0x01A0) }, /* HHP PDT */
+	{ USB_DEVICE(0x0543, 0x0ED9) }, /* ViewSonic Color Pocket PC V35 */
+	{ USB_DEVICE(0x0543, 0x1527) }, /* ViewSonic Color Pocket PC V36 */
+	{ USB_DEVICE(0x0543, 0x1529) }, /* ViewSonic Color Pocket PC V37 */
+	{ USB_DEVICE(0x0543, 0x152B) }, /* ViewSonic Color Pocket PC V38 */
+	{ USB_DEVICE(0x0543, 0x152E) }, /* ViewSonic Pocket PC */
+	{ USB_DEVICE(0x0543, 0x1921) }, /* ViewSonic Communicator Pocket PC */
+	{ USB_DEVICE(0x0543, 0x1922) }, /* ViewSonic Smartphone */
+	{ USB_DEVICE(0x0543, 0x1923) }, /* ViewSonic Pocket PC V30 */
+	{ USB_DEVICE(0x05E0, 0x2000) }, /* Symbol USB Sync */
+	{ USB_DEVICE(0x05E0, 0x2001) }, /* Symbol USB Sync 0x2001 */
+	{ USB_DEVICE(0x05E0, 0x2002) }, /* Symbol USB Sync 0x2002 */
+	{ USB_DEVICE(0x05E0, 0x2003) }, /* Symbol USB Sync 0x2003 */
+	{ USB_DEVICE(0x05E0, 0x2004) }, /* Symbol USB Sync 0x2004 */
+	{ USB_DEVICE(0x05E0, 0x2005) }, /* Symbol USB Sync 0x2005 */
+	{ USB_DEVICE(0x05E0, 0x2006) }, /* Symbol USB Sync 0x2006 */
+	{ USB_DEVICE(0x05E0, 0x2007) }, /* Symbol USB Sync 0x2007 */
+	{ USB_DEVICE(0x05E0, 0x2008) }, /* Symbol USB Sync 0x2008 */
+	{ USB_DEVICE(0x05E0, 0x2009) }, /* Symbol USB Sync 0x2009 */
+	{ USB_DEVICE(0x05E0, 0x200A) }, /* Symbol USB Sync 0x200A */
+	{ USB_DEVICE(0x067E, 0x1001) }, /* Intermec Mobile Computer */
+	{ USB_DEVICE(0x07CF, 0x2001) }, /* CASIO USB Sync 2001 */
+	{ USB_DEVICE(0x07CF, 0x2002) }, /* CASIO USB Sync 2002 */
+	{ USB_DEVICE(0x07CF, 0x2003) }, /* CASIO USB Sync 2003 */
 	{ USB_DEVICE(0x0930, 0x0700) }, /* TOSHIBA USB Sync 0700 */
 	{ USB_DEVICE(0x0930, 0x0705) }, /* TOSHIBA Pocket PC e310 */
+	{ USB_DEVICE(0x0930, 0x0706) }, /* TOSHIBA Pocket PC e740 */
 	{ USB_DEVICE(0x0930, 0x0707) }, /* TOSHIBA Pocket PC e330 Series */
 	{ USB_DEVICE(0x0930, 0x0708) }, /* TOSHIBA Pocket PC e350 Series */
-	{ USB_DEVICE(0x0930, 0x0706) }, /* TOSHIBA Pocket PC e740 */
 	{ USB_DEVICE(0x0930, 0x0709) }, /* TOSHIBA Pocket PC e750 Series */
 	{ USB_DEVICE(0x0930, 0x070A) }, /* TOSHIBA Pocket PC e400 Series */
 	{ USB_DEVICE(0x0930, 0x070B) }, /* TOSHIBA Pocket PC e800 Series */
+	{ USB_DEVICE(0x094B, 0x0001) }, /* Linkup Systems USB Sync */
+	{ USB_DEVICE(0x0960, 0x0065) }, /* BCOM USB Sync 0065 */
+	{ USB_DEVICE(0x0960, 0x0066) }, /* BCOM USB Sync 0066 */
+	{ USB_DEVICE(0x0960, 0x0067) }, /* BCOM USB Sync 0067 */
+	{ USB_DEVICE(0x0961, 0x0010) }, /* Portatec USB Sync */
+	{ USB_DEVICE(0x099E, 0x0052) }, /* Trimble GeoExplorer */
+	{ USB_DEVICE(0x099E, 0x4000) }, /* TDS Data Collector */
+	{ USB_DEVICE(0x0B05, 0x4200) }, /* ASUS USB Sync */
+	{ USB_DEVICE(0x0B05, 0x4201) }, /* ASUS USB Sync */
+	{ USB_DEVICE(0x0B05, 0x4202) }, /* ASUS USB Sync */
+	{ USB_DEVICE(0x0B05, 0x420F) }, /* ASUS USB Sync */
+	{ USB_DEVICE(0x0B05, 0x9200) }, /* ASUS USB Sync */
+	{ USB_DEVICE(0x0B05, 0x9202) }, /* ASUS USB Sync */
 	{ USB_DEVICE(0x0BB4, 0x00CE) }, /* HTC USB Sync */
 	{ USB_DEVICE(0x0BB4, 0x0A01) }, /* PocketPC USB Sync */
 	{ USB_DEVICE(0x0BB4, 0x0A02) }, /* PocketPC USB Sync */
@@ -422,116 +475,67 @@ static struct usb_device_id ipaq_id_table [] = {
 	{ USB_DEVICE(0x0BB4, 0x0A9D) }, /* SmartPhone USB Sync */
 	{ USB_DEVICE(0x0BB4, 0x0A9E) }, /* SmartPhone USB Sync */
 	{ USB_DEVICE(0x0BB4, 0x0A9F) }, /* SmartPhone USB Sync */
-	{ USB_DEVICE(0x0409, 0x00D5) }, /* NEC USB Sync */
-	{ USB_DEVICE(0x0409, 0x00D6) }, /* NEC USB Sync */
-	{ USB_DEVICE(0x0409, 0x00D7) }, /* NEC USB Sync */
-	{ USB_DEVICE(0x0409, 0x8024) }, /* NEC USB Sync */
-	{ USB_DEVICE(0x0409, 0x8025) }, /* NEC USB Sync */
-	{ USB_DEVICE(0x04A4, 0x0014) }, /* Hitachi USB Sync */
 	{ USB_DEVICE(0x0BF8, 0x1001) }, /* Fujitsu Siemens Computers USB Sync */
-	{ USB_DEVICE(0x0F98, 0x0201) }, /* Cyberbank USB Sync */
-	{ USB_DEVICE(0x0502, 0x16E1) }, /* Acer n10 Handheld USB Sync */
-	{ USB_DEVICE(0x0502, 0x16E3) }, /* Acer n30 Handheld USB Sync */
-	{ USB_DEVICE(0x0502, 0x16E2) }, /* Acer n20 Handheld USB Sync */
-	{ USB_DEVICE(0x0502, 0x1631) }, /* c10 Series */
-	{ USB_DEVICE(0x0502, 0x1632) }, /* c20 Series */
-	{ USB_DEVICE(0x0B05, 0x9202) }, /* ASUS USB Sync */
-	{ USB_DEVICE(0x0B05, 0x420F) }, /* ASUS USB Sync */
-	{ USB_DEVICE(0x0B05, 0x4200) }, /* ASUS USB Sync */
-	{ USB_DEVICE(0x0B05, 0x4201) }, /* ASUS USB Sync */
-	{ USB_DEVICE(0x0B05, 0x4202) }, /* ASUS USB Sync */
-	{ USB_DEVICE(0x0B05, 0x9200) }, /* ASUS USB Sync */
+	{ USB_DEVICE(0x0C44, 0x03A2) }, /* Motorola iDEN Smartphone */
 	{ USB_DEVICE(0x0C8E, 0x6000) }, /* Cesscom Luxian Series */
-	{ USB_DEVICE(0x04AD, 0x0301) }, /* USB Sync 0301 */
-	{ USB_DEVICE(0x04AD, 0x0302) }, /* USB Sync 0302 */
-	{ USB_DEVICE(0x04AD, 0x0303) }, /* USB Sync 0303 */
+	{ USB_DEVICE(0x0CAD, 0x9001) }, /* Motorola PowerPad Pocket PC Device */
+	{ USB_DEVICE(0x0F4E, 0x0200) }, /* Freedom Scientific USB Sync */
+	{ USB_DEVICE(0x0F98, 0x0201) }, /* Cyberbank USB Sync */
+	{ USB_DEVICE(0x0FB8, 0x3001) }, /* Wistron USB Sync */
+	{ USB_DEVICE(0x0FB8, 0x3002) }, /* Wistron USB Sync */
+	{ USB_DEVICE(0x0FB8, 0x3003) }, /* Wistron USB Sync */
+	{ USB_DEVICE(0x0FB8, 0x4001) }, /* Wistron USB Sync */
+	{ USB_DEVICE(0x1066, 0x00CE) }, /* E-TEN USB Sync */
 	{ USB_DEVICE(0x1066, 0x0300) }, /* E-TEN P3XX Pocket PC */
 	{ USB_DEVICE(0x1066, 0x0500) }, /* E-TEN P5XX Pocket PC */
 	{ USB_DEVICE(0x1066, 0x0600) }, /* E-TEN P6XX Pocket PC */
 	{ USB_DEVICE(0x1066, 0x0700) }, /* E-TEN P7XX Pocket PC */
-	{ USB_DEVICE(0x1066, 0x00CE) }, /* E-TEN USB Sync */
-	{ USB_DEVICE(0x0F4E, 0x0200) }, /* Freedom Scientific USB Sync */
-	{ USB_DEVICE(0x04C5, 0x1058) }, /* FUJITSU USB Sync */
-	{ USB_DEVICE(0x04C5, 0x1079) }, /* FUJITSU USB Sync */
-	{ USB_DEVICE(0x067E, 0x1001) }, /* Intermec Mobile Computer */
-	{ USB_DEVICE(0x04f1, 0x3011) }, /* JVC USB Sync */
-	{ USB_DEVICE(0x04F1, 0x3012) }, /* JVC USB Sync */
-	{ USB_DEVICE(0x3708, 0x20CE) }, /* Legend USB Sync */
-	{ USB_DEVICE(0x3708, 0x21CE) }, /* Lenovo USB Sync */
-	{ USB_DEVICE(0x043E, 0x9C01) }, /* LGE USB Sync */
-	{ USB_DEVICE(0x04DA, 0x2500) }, /* Panasonic USB Sync */
-	{ USB_DEVICE(0x3340, 0x0B1C) }, /* Generic PPC StrongARM */
-	{ USB_DEVICE(0x3340, 0x0E3A) }, /* Generic PPC USB Sync */
-	{ USB_DEVICE(0x3340, 0x0F3A) }, /* Generic SmartPhone USB Sync */
-	{ USB_DEVICE(0x3340, 0x0F1C) }, /* Itautec USB Sync */
-	{ USB_DEVICE(0x3340, 0x1326) }, /* Itautec USB Sync */
-	{ USB_DEVICE(0x3340, 0x3326) }, /* MEDION Winodws Moble USB Sync */
+	{ USB_DEVICE(0x1114, 0x0001) }, /* Psion Teklogix Sync 753x */
+	{ USB_DEVICE(0x1114, 0x0004) }, /* Psion Teklogix Sync netBookPro */
+	{ USB_DEVICE(0x1114, 0x0006) }, /* Psion Teklogix Sync 7525 */
+	{ USB_DEVICE(0x1182, 0x1388) }, /* VES USB Sync */
+	{ USB_DEVICE(0x11D9, 0x1002) }, /* Rugged Pocket PC 2003 */
+	{ USB_DEVICE(0x11D9, 0x1003) }, /* Rugged Pocket PC 2003 */
+	{ USB_DEVICE(0x1231, 0xCE01) }, /* USB Sync 03 */
+	{ USB_DEVICE(0x1231, 0xCE02) }, /* USB Sync 03 */
+	{ USB_DEVICE(0x1690, 0x0601) }, /* Askey USB Sync */
+	{ USB_DEVICE(0x22B8, 0x4204) }, /* Motorola MPx200 Smartphone */
+	{ USB_DEVICE(0x22B8, 0x4214) }, /* Motorola MPc GSM */
+	{ USB_DEVICE(0x22B8, 0x4224) }, /* Motorola MPx220 Smartphone */
+	{ USB_DEVICE(0x22B8, 0x4234) }, /* Motorola MPc CDMA */
+	{ USB_DEVICE(0x22B8, 0x4244) }, /* Motorola MPx100 Smartphone */
+	{ USB_DEVICE(0x3340, 0x011C) }, /* Mio DigiWalker PPC StrongARM */
 	{ USB_DEVICE(0x3340, 0x0326) }, /* Mio DigiWalker 338 */
 	{ USB_DEVICE(0x3340, 0x0426) }, /* Mio DigiWalker 338 */
-	{ USB_DEVICE(0x3340, 0x011C) }, /* Mio DigiWalker PPC StrongARM */
-	{ USB_DEVICE(0x3340, 0x053A) }, /* Mio DigiWalker SmartPhone USB Sync */
 	{ USB_DEVICE(0x3340, 0x043A) }, /* Mio DigiWalker USB Sync */
-	{ USB_DEVICE(0x3340, 0x071C) }, /* MiTAC USB Sync */
 	{ USB_DEVICE(0x3340, 0x051C) }, /* MiTAC USB Sync 528 */
-	{ USB_DEVICE(0x3340, 0x2326) }, /* Vobis USB Sync */
+	{ USB_DEVICE(0x3340, 0x053A) }, /* Mio DigiWalker SmartPhone USB Sync */
+	{ USB_DEVICE(0x3340, 0x071C) }, /* MiTAC USB Sync */
+	{ USB_DEVICE(0x3340, 0x0B1C) }, /* Generic PPC StrongARM */
+	{ USB_DEVICE(0x3340, 0x0E3A) }, /* Generic PPC USB Sync */
+	{ USB_DEVICE(0x3340, 0x0F1C) }, /* Itautec USB Sync */
+	{ USB_DEVICE(0x3340, 0x0F3A) }, /* Generic SmartPhone USB Sync */
+	{ USB_DEVICE(0x3340, 0x1326) }, /* Itautec USB Sync */
 	{ USB_DEVICE(0x3340, 0x191C) }, /* YAKUMO USB Sync */
+	{ USB_DEVICE(0x3340, 0x2326) }, /* Vobis USB Sync */
+	{ USB_DEVICE(0x3340, 0x3326) }, /* MEDION Winodws Moble USB Sync */
+	{ USB_DEVICE(0x3708, 0x20CE) }, /* Legend USB Sync */
+	{ USB_DEVICE(0x3708, 0x21CE) }, /* Lenovo USB Sync */
 	{ USB_DEVICE(0x4113, 0x0210) }, /* Mobile Media Technology USB Sync */
 	{ USB_DEVICE(0x4113, 0x0211) }, /* Mobile Media Technology USB Sync */
 	{ USB_DEVICE(0x4113, 0x0400) }, /* Mobile Media Technology USB Sync */
 	{ USB_DEVICE(0x4113, 0x0410) }, /* Mobile Media Technology USB Sync */
-	{ USB_DEVICE(0x0CAD, 0x9001) }, /* Motorola PowerPad Pocket PC Device */
-	{ USB_DEVICE(0x0C44, 0x03A2) }, /* Motorola iDEN Smartphone */
-	{ USB_DEVICE(0x04E8, 0x6611) }, /* Samsung MITs USB Sync */
-	{ USB_DEVICE(0x04E8, 0x6613) }, /* Samsung MITs USB Sync */
-	{ USB_DEVICE(0x04E8, 0x6615) }, /* Samsung MITs USB Sync */
-	{ USB_DEVICE(0x04E8, 0x6617) }, /* Samsung MITs USB Sync */
-	{ USB_DEVICE(0x04E8, 0x6619) }, /* Samsung MITs USB Sync */
-	{ USB_DEVICE(0x04E8, 0x661B) }, /* Samsung MITs USB Sync */
-	{ USB_DEVICE(0x04E8, 0x5F00) }, /* Samsung NEXiO USB Sync */
-	{ USB_DEVICE(0x04E8, 0x5F01) }, /* Samsung NEXiO USB Sync */
-	{ USB_DEVICE(0x04E8, 0x5F02) }, /* Samsung NEXiO USB Sync */
-	{ USB_DEVICE(0x04E8, 0x5F03) }, /* Samsung NEXiO USB Sync */
-	{ USB_DEVICE(0x04E8, 0x5F04) }, /* Samsung NEXiO USB Sync */
-	{ USB_DEVICE(0x04E8, 0x662E) }, /* Samsung MITs USB Sync */
-	{ USB_DEVICE(0x04E8, 0x6630) }, /* Samsung MITs USB Sync */
-	{ USB_DEVICE(0x04E8, 0x6632) }, /* Samsung MITs USB Sync */
+	{ USB_DEVICE(0x413C, 0x4001) }, /* Dell Axim USB Sync */
+	{ USB_DEVICE(0x413C, 0x4002) }, /* Dell Axim USB Sync */
+	{ USB_DEVICE(0x413C, 0x4003) }, /* Dell Axim USB Sync */
+	{ USB_DEVICE(0x413C, 0x4004) }, /* Dell Axim USB Sync */
+	{ USB_DEVICE(0x413C, 0x4005) }, /* Dell Axim USB Sync */
+	{ USB_DEVICE(0x413C, 0x4006) }, /* Dell Axim USB Sync */
+	{ USB_DEVICE(0x413C, 0x4007) }, /* Dell Axim USB Sync */
+	{ USB_DEVICE(0x413C, 0x4008) }, /* Dell Axim USB Sync */
+	{ USB_DEVICE(0x413C, 0x4009) }, /* Dell Axim USB Sync */
 	{ USB_DEVICE(0x4505, 0x0010) }, /* Smartphone */
-	{ USB_DEVICE(0x05E0, 0x2000) }, /* Symbol USB Sync */
-	{ USB_DEVICE(0x05E0, 0x2001) }, /* Symbol USB Sync 0x2001 */
-	{ USB_DEVICE(0x05E0, 0x2002) }, /* Symbol USB Sync 0x2002 */
-	{ USB_DEVICE(0x05E0, 0x2003) }, /* Symbol USB Sync 0x2003 */
-	{ USB_DEVICE(0x05E0, 0x2004) }, /* Symbol USB Sync 0x2004 */
-	{ USB_DEVICE(0x05E0, 0x2005) }, /* Symbol USB Sync 0x2005 */
-	{ USB_DEVICE(0x05E0, 0x2006) }, /* Symbol USB Sync 0x2006 */
-	{ USB_DEVICE(0x05E0, 0x2007) }, /* Symbol USB Sync 0x2007 */
-	{ USB_DEVICE(0x05E0, 0x2008) }, /* Symbol USB Sync 0x2008 */
-	{ USB_DEVICE(0x05E0, 0x2009) }, /* Symbol USB Sync 0x2009 */
-	{ USB_DEVICE(0x05E0, 0x200A) }, /* Symbol USB Sync 0x200A */
-	{ USB_DEVICE(0x1182, 0x1388) }, /* VES USB Sync */
-	{ USB_DEVICE(0x0543, 0x0ED9) }, /* ViewSonic Color Pocket PC V35 */
-	{ USB_DEVICE(0x0543, 0x1527) }, /* ViewSonic Color Pocket PC V36 */
-	{ USB_DEVICE(0x0543, 0x1529) }, /* ViewSonic Color Pocket PC V37 */
-	{ USB_DEVICE(0x0543, 0x152B) }, /* ViewSonic Color Pocket PC V38 */
-	{ USB_DEVICE(0x0543, 0x152E) }, /* ViewSonic Pocket PC */
-	{ USB_DEVICE(0x0543, 0x1921) }, /* ViewSonic Communicator Pocket PC */
-	{ USB_DEVICE(0x0543, 0x1922) }, /* ViewSonic Smartphone */
-	{ USB_DEVICE(0x0543, 0x1923) }, /* ViewSonic Pocket PC V30 */
-	{ USB_DEVICE(0x0536, 0x01A0) }, /* HHP PDT */
-	{ USB_DEVICE(0x099E, 0x0052) }, /* Trimble GeoExplorer */
-	{ USB_DEVICE(0x099E, 0x4000) }, /* TDS Data Collector */
-	{ USB_DEVICE(0x0FB8, 0x3001) }, /* Wistron USB Sync */
-	{ USB_DEVICE(0x0FB8, 0x3002) }, /* Wistron USB Sync */
-	{ USB_DEVICE(0x0FB8, 0x3003) }, /* Wistron USB Sync */
-	{ USB_DEVICE(0x0FB8, 0x4001) }, /* Wistron USB Sync */
-	{ USB_DEVICE(0x11D9, 0x1003) }, /* Rugged Pocket PC 2003 */
-	{ USB_DEVICE(0x11D9, 0x1002) }, /* Rugged Pocket PC 2003 */
-	{ USB_DEVICE(0x22B8, 0x4204) }, /* Motorola MPx200 Smartphone */
-	{ USB_DEVICE(0x22B8, 0x4214) }, /* Motorola MPc GSM */
-	{ USB_DEVICE(0x22B8, 0x4224) }, /* Motorola MPx220 Smartphone */
-	{ USB_DEVICE(0x22B8, 0x4234) }, /* Motorola MPc CDMA */
-	{ USB_DEVICE(0x22B8, 0x4244) }, /* Motorola MPx100 Smartphone */
-	{ USB_DEVICE(0x1231, 0xCE01) }, /* USB Sync 03 */
-	{ USB_DEVICE(0x1231, 0xCE02) }, /* USB Sync 03 */
+	{ USB_DEVICE(0x5E04, 0xCE00) }, /* SAGEM Wireless Assistant */
 	{ }                             /* Terminating entry */
 };
 
-- 
cgit v1.1


From 46f116eab81b21c6ae8c4f169498c632b1f94bf1 Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Mon, 24 Oct 2005 22:42:35 +0200
Subject: [PATCH] USB: cdc-acm patch to use kzalloc

another one to use kzalloc. Please apply.

Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/class/cdc-acm.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
index 16ecad3..1b47514 100644
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -827,11 +827,10 @@ skip_normal_probe:
 		return -ENODEV;
 	}
 
-	if (!(acm = kmalloc(sizeof(struct acm), GFP_KERNEL))) {
-		dev_dbg(&intf->dev, "out of memory (acm kmalloc)\n");
+	if (!(acm = kzalloc(sizeof(struct acm), GFP_KERNEL))) {
+		dev_dbg(&intf->dev, "out of memory (acm kzalloc)\n");
 		goto alloc_fail;
 	}
-	memset(acm, 0, sizeof(struct acm));
 
 	ctrlsize = le16_to_cpu(epctrl->wMaxPacketSize);
 	readsize = le16_to_cpu(epread->wMaxPacketSize);
-- 
cgit v1.1


From 478a3bab8c87a9ba4a4ba338314e32bb0c378e62 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Wed, 19 Oct 2005 12:52:02 -0400
Subject: [PATCH] USB: Always do usb-handoff

This revised patch (as586b) makes usb-handoff permanently true and no
longer a kernel boot parameter.  It also removes the piix3_usb quirk code;
that was nothing more than an early version of the USB handoff code
(written at a time when Intel's PIIX3 was about the only motherboard with
USB support).  And it adds identifiers for the three PCI USB controller
classes to pci_ids.h.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/host/pci-quirks.c | 46 +++----------------------------------------
 1 file changed, 3 insertions(+), 43 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c
index f7411ca..b7fd3f6 100644
--- a/drivers/usb/host/pci-quirks.c
+++ b/drivers/usb/host/pci-quirks.c
@@ -23,33 +23,6 @@
 #include <linux/acpi.h>
 
 
-/*
- * PIIX3 USB: We have to disable USB interrupts that are
- * hardwired to PIRQD# and may be shared with an
- * external device.
- *
- * Legacy Support Register (LEGSUP):
- *     bit13:  USB PIRQ Enable (USBPIRQDEN),
- *     bit4:   Trap/SMI On IRQ Enable (USBSMIEN).
- *
- * We mask out all r/wc bits, too.
- */
-static void __devinit quirk_piix3_usb(struct pci_dev *dev)
-{
-	u16 legsup;
-
-	pci_read_config_word(dev, 0xc0, &legsup);
-	legsup &= 0x50ef;
-	pci_write_config_word(dev, 0xc0, legsup);
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82371SB_2,	quirk_piix3_usb );
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82371AB_2,	quirk_piix3_usb );
-
-
-/* FIXME these should be the guts of hcd->reset() methods; resolve all
- * the differences between this version and the HCD's version.
- */
-
 #define UHCI_USBLEGSUP		0xc0		/* legacy support */
 #define UHCI_USBCMD		0		/* command register */
 #define UHCI_USBINTR		4		/* interrupt register */
@@ -83,13 +56,6 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL,	PCI_DEVICE_ID_INTEL_82371AB_2,	qui
 #define EHCI_USBLEGCTLSTS	4		/* legacy control/status */
 #define EHCI_USBLEGCTLSTS_SOOE	(1 << 13)	/* SMI on ownership change */
 
-int usb_early_handoff __devinitdata = 0;
-static int __init usb_handoff_early(char *str)
-{
-	usb_early_handoff = 1;
-	return 0;
-}
-__setup("usb-handoff", usb_handoff_early);
 
 /*
  * Make sure the controller is completely inactive, unable to
@@ -320,17 +286,11 @@ static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev)
 
 static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
 {
-	if (!usb_early_handoff)
-		return;
-
-	if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x00)) { /* UHCI */
+	if (pdev->class == PCI_CLASS_SERIAL_USB_UHCI)
 		quirk_usb_handoff_uhci(pdev);
-	} else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x10)) { /* OHCI */
+	else if (pdev->class == PCI_CLASS_SERIAL_USB_OHCI)
 		quirk_usb_handoff_ohci(pdev);
-	} else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x20)) { /* EHCI */
+	else if (pdev->class == PCI_CLASS_SERIAL_USB_EHCI)
 		quirk_usb_disable_ehci(pdev);
-	}
-
-	return;
 }
 DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_usb_early_handoff);
-- 
cgit v1.1


From 423e489d704d05c6e8c2927fb1854db85914912a Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Wed, 19 Oct 2005 13:06:13 -0400
Subject: [PATCH] hid-core: Add Clear-Halt on the Interrupt-in endpoint

This patch (as577) adds a Clear-Halt call on the Interrupt-in endpoint
during input device configuration.  Without it my HP USB keyboard doesn't
work.

Vojtech says it's worth trying, since it might help with some recalcitrant
devices.  On the other hand, it might interfere with others.  I'm
submitting it so that it can get tested by a range of users.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/input/hid-core.c | 3 +++
 1 file changed, 3 insertions(+)

(limited to 'drivers')

diff --git a/drivers/usb/input/hid-core.c b/drivers/usb/input/hid-core.c
index f7fcce7..79ddce4 100644
--- a/drivers/usb/input/hid-core.c
+++ b/drivers/usb/input/hid-core.c
@@ -1784,6 +1784,9 @@ static struct hid_device *usb_hid_configure(struct usb_interface *intf)
 	hid->urbctrl->transfer_dma = hid->ctrlbuf_dma;
 	hid->urbctrl->transfer_flags |= (URB_NO_TRANSFER_DMA_MAP | URB_NO_SETUP_DMA_MAP);
 
+	/* May be needed for some devices */
+	usb_clear_halt(hid->dev, hid->urbin->pipe);
+
 	return hid;
 
 fail:
-- 
cgit v1.1


From b876aef7f890d8c59a45b78858a36cf60fddf522 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Sun, 23 Oct 2005 19:38:56 -0700
Subject: [PATCH] PATCH: usb-storage: move GetMaxLUN later in time

This patch is originally from Alan Stern (as557).  It has been re-diffed
against a current tree, and I also corrected a minor merging error.

Some time ago we introduced a delay before device scanning, because many
devices do not like to receive SCSI commands right after enumeration.
Now it turns out there's a device that doesn't like to receive
Get-Max-LUN right after enumeration either.  Accordingly this patch
delays the Get-Max-LUN request until the beginning of the scanning
procedure.  This fixes Bugzilla entry #5010.

Three things are worth noting.  First, I removed the locking code from
usb_stor_acquire_resources.  It's not needed, because the locking is to
protect against disconnect events and acquire_resources is only called
during probe (so the disconnect routine can't be called).  Second, I
initialized to 0 the buffer used for the Get-Max-LUN response.  It's not
really necessary, but it will prevent random values from showing up in
the debugging log when the request fails.  Third, I added a test against
the SINGLE_LUN flag.  This will allow us to use the flag to indicate
Bulk-only devices that can't handle Get-Max-LUN.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/storage/transport.c |  1 +
 drivers/usb/storage/usb.c       | 30 +++++++++++++-----------------
 2 files changed, 14 insertions(+), 17 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c
index c1ba530..e89e945 100644
--- a/drivers/usb/storage/transport.c
+++ b/drivers/usb/storage/transport.c
@@ -923,6 +923,7 @@ int usb_stor_Bulk_max_lun(struct us_data *us)
 	int result;
 
 	/* issue the command */
+	us->iobuf[0] = 0;
 	result = usb_stor_control_msg(us, us->recv_ctrl_pipe,
 				 US_BULK_GET_MAX_LUN, 
 				 USB_DIR_IN | USB_TYPE_CLASS | 
diff --git a/drivers/usb/storage/usb.c b/drivers/usb/storage/usb.c
index 5164900..92ee079 100644
--- a/drivers/usb/storage/usb.c
+++ b/drivers/usb/storage/usb.c
@@ -747,25 +747,13 @@ static int usb_stor_acquire_resources(struct us_data *us)
 		return -ENOMEM;
 	}
 
-	/* Lock the device while we carry out the next two operations */
-	down(&us->dev_semaphore);
-
-	/* For bulk-only devices, determine the max LUN value */
-	if (us->protocol == US_PR_BULK) {
-		p = usb_stor_Bulk_max_lun(us);
-		if (p < 0) {
-			up(&us->dev_semaphore);
-			return p;
-		}
-		us->max_lun = p;
-	}
-
 	/* Just before we start our control thread, initialize
 	 * the device if it needs initialization */
-	if (us->unusual_dev->initFunction)
-		us->unusual_dev->initFunction(us);
-
-	up(&us->dev_semaphore);
+	if (us->unusual_dev->initFunction) {
+		p = us->unusual_dev->initFunction(us);
+		if (p)
+			return p;
+	}
 
 	/* Start up our control thread */
 	p = kernel_thread(usb_stor_control_thread, us, CLONE_VM);
@@ -904,6 +892,14 @@ retry:
 
 	/* If the device is still connected, perform the scanning */
 	if (!test_bit(US_FLIDX_DISCONNECTING, &us->flags)) {
+
+		/* For bulk-only devices, determine the max LUN value */
+		if (us->protocol == US_PR_BULK &&
+				!(us->flags & US_FL_SINGLE_LUN)) {
+			down(&us->dev_semaphore);
+			us->max_lun = usb_stor_Bulk_max_lun(us);
+			up(&us->dev_semaphore);
+		}
 		scsi_scan_host(us_to_host(us));
 		printk(KERN_DEBUG "usb-storage: device scan complete\n");
 
-- 
cgit v1.1


From bbafa4668f37f5093a3ae2a8b0cbe327e24e12da Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Sun, 23 Oct 2005 19:40:22 -0700
Subject: [PATCH] PATCH: usb-storage: allocate separate sense buffer

This patch is from Alan Stern (as560).  It has been rediffed against a
current tree.

This patch allocates a separate buffer for usb-storage to use when
auto-sensing.  Up to now we have been using the sense buffer embedded in a
scsi_cmnd struct, which is dangerous on hosts that (a) don't do
cache-coherent DMA or (b) have DMA alignment restrictions.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/storage/transport.c | 5 +++--
 drivers/usb/storage/usb.c       | 8 ++++++++
 drivers/usb/storage/usb.h       | 2 ++
 3 files changed, 13 insertions(+), 2 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c
index e89e945..7ca896a 100644
--- a/drivers/usb/storage/transport.c
+++ b/drivers/usb/storage/transport.c
@@ -636,11 +636,11 @@ void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us)
 
 		/* use the new buffer we have */
 		old_request_buffer = srb->request_buffer;
-		srb->request_buffer = srb->sense_buffer;
+		srb->request_buffer = us->sensebuf;
 
 		/* set the buffer length for transfer */
 		old_request_bufflen = srb->request_bufflen;
-		srb->request_bufflen = 18;
+		srb->request_bufflen = US_SENSE_SIZE;
 
 		/* set up for no scatter-gather use */
 		old_sg = srb->use_sg;
@@ -652,6 +652,7 @@ void usb_stor_invoke_transport(struct scsi_cmnd *srb, struct us_data *us)
 		temp_result = us->transport(us->srb, us);
 
 		/* let's clean up right away */
+		memcpy(srb->sense_buffer, us->sensebuf, US_SENSE_SIZE);
 		srb->resid = old_resid;
 		srb->request_buffer = old_request_buffer;
 		srb->request_bufflen = old_request_bufflen;
diff --git a/drivers/usb/storage/usb.c b/drivers/usb/storage/usb.c
index 92ee079..eb90181 100644
--- a/drivers/usb/storage/usb.c
+++ b/drivers/usb/storage/usb.c
@@ -467,6 +467,12 @@ static int associate_dev(struct us_data *us, struct usb_interface *intf)
 		US_DEBUGP("I/O buffer allocation failed\n");
 		return -ENOMEM;
 	}
+
+	us->sensebuf = kmalloc(US_SENSE_SIZE, GFP_KERNEL);
+	if (!us->sensebuf) {
+		US_DEBUGP("Sense buffer allocation failed\n");
+		return -ENOMEM;
+	}
 	return 0;
 }
 
@@ -800,6 +806,8 @@ static void dissociate_dev(struct us_data *us)
 {
 	US_DEBUGP("-- %s\n", __FUNCTION__);
 
+	kfree(us->sensebuf);
+
 	/* Free the device-related DMA-mapped buffers */
 	if (us->cr)
 		usb_buffer_free(us->pusb_dev, sizeof(*us->cr), us->cr,
diff --git a/drivers/usb/storage/usb.h b/drivers/usb/storage/usb.h
index a195ada..dfa4dc7 100644
--- a/drivers/usb/storage/usb.h
+++ b/drivers/usb/storage/usb.h
@@ -117,6 +117,7 @@ enum { US_DO_ALL_FLAGS };
  */
 
 #define US_IOBUF_SIZE		64	/* Size of the DMA-mapped I/O buffer */
+#define US_SENSE_SIZE		18	/* Size of the autosense data buffer */
 
 typedef int (*trans_cmnd)(struct scsi_cmnd *, struct us_data*);
 typedef int (*trans_reset)(struct us_data*);
@@ -168,6 +169,7 @@ struct us_data {
 	struct usb_ctrlrequest	*cr;		 /* control requests	 */
 	struct usb_sg_request	current_sg;	 /* scatter-gather req.  */
 	unsigned char		*iobuf;		 /* I/O buffer		 */
+	unsigned char		*sensebuf;	 /* sense data buffer	 */
 	dma_addr_t		cr_dma;		 /* buffer DMA addresses */
 	dma_addr_t		iobuf_dma;
 
-- 
cgit v1.1


From ce2596df79ddbac605a290f4c7cf011cb40524fc Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Sun, 23 Oct 2005 19:41:39 -0700
Subject: [PATCH] PATCH: usb-storage: implement minimal PM

This patch from Alan Stern started as as568.  It has been rediffed against
a current tree.

This patch adds minimal suspend/resume support to usb-storage.  Just enough
for it to qualify as PM-aware.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/storage/usb.c | 58 +++++++++++++++++++++++++++++++++++++----------
 1 file changed, 46 insertions(+), 12 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/storage/usb.c b/drivers/usb/storage/usb.c
index eb90181..c1a9026 100644
--- a/drivers/usb/storage/usb.c
+++ b/drivers/usb/storage/usb.c
@@ -111,11 +111,6 @@ static atomic_t total_threads = ATOMIC_INIT(0);
 static DECLARE_COMPLETION(threads_gone);
 
 
-static int storage_probe(struct usb_interface *iface,
-			 const struct usb_device_id *id);
-
-static void storage_disconnect(struct usb_interface *iface);
-
 /* The entries in this table, except for final ones here
  * (USB_MASS_STORAGE_CLASS and the empty entry), correspond,
  * line for line with the entries of us_unsuaul_dev_list[].
@@ -233,13 +228,40 @@ static struct us_unusual_dev us_unusual_dev_list[] = {
 	{ NULL }
 };
 
-static struct usb_driver usb_storage_driver = {
-	.owner =	THIS_MODULE,
-	.name =		"usb-storage",
-	.probe =	storage_probe,
-	.disconnect =	storage_disconnect,
-	.id_table =	storage_usb_ids,
-};
+
+#ifdef CONFIG_PM	/* Minimal support for suspend and resume */
+
+static int storage_suspend(struct usb_interface *iface, pm_message_t message)
+{
+	struct us_data *us = usb_get_intfdata(iface);
+
+	/* Wait until no command is running */
+	down(&us->dev_semaphore);
+
+	US_DEBUGP("%s\n", __FUNCTION__);
+	iface->dev.power.power_state.event = message.event;
+
+	/* When runtime PM is working, we'll set a flag to indicate
+	 * whether we should autoresume when a SCSI request arrives. */
+
+	up(&us->dev_semaphore);
+	return 0;
+}
+
+static int storage_resume(struct usb_interface *iface)
+{
+	struct us_data *us = usb_get_intfdata(iface);
+
+	down(&us->dev_semaphore);
+
+	US_DEBUGP("%s\n", __FUNCTION__);
+	iface->dev.power.power_state.event = PM_EVENT_ON;
+
+	up(&us->dev_semaphore);
+	return 0;
+}
+
+#endif /* CONFIG_PM */
 
 /*
  * fill_inquiry_response takes an unsigned char array (which must
@@ -1042,6 +1064,18 @@ static void storage_disconnect(struct usb_interface *intf)
  * Initialization and registration
  ***********************************************************************/
 
+static struct usb_driver usb_storage_driver = {
+	.owner =	THIS_MODULE,
+	.name =		"usb-storage",
+	.probe =	storage_probe,
+	.disconnect =	storage_disconnect,
+#ifdef CONFIG_PM
+	.suspend =	storage_suspend,
+	.resume =	storage_resume,
+#endif
+	.id_table =	storage_usb_ids,
+};
+
 static int __init usb_stor_init(void)
 {
 	int retval;
-- 
cgit v1.1


From 3f13e66e219238e025ff561d69826da9342c3f4a Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Sun, 23 Oct 2005 19:43:36 -0700
Subject: [PATCH] PATCH: usb-storage: use kthread API

This patch is originally from Alan Stern (as569).  It has been rediffed
against a current tree.

This patch converts usb-storage to use the kthread API for creating its
control and scanning threads.  The new code doesn't use kthread_stop
because the threads need (or will need in the future) to exit
asynchronously.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/storage/usb.c | 63 ++++++++++++++++-------------------------------
 drivers/usb/storage/usb.h |  3 ---
 2 files changed, 21 insertions(+), 45 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/storage/usb.c b/drivers/usb/storage/usb.c
index c1a9026..3847ebe 100644
--- a/drivers/usb/storage/usb.c
+++ b/drivers/usb/storage/usb.c
@@ -54,6 +54,7 @@
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/slab.h>
+#include <linux/kthread.h>
 
 #include <scsi/scsi.h>
 #include <scsi/scsi_cmnd.h>
@@ -310,22 +311,7 @@ static int usb_stor_control_thread(void * __us)
 	struct us_data *us = (struct us_data *)__us;
 	struct Scsi_Host *host = us_to_host(us);
 
-	lock_kernel();
-
-	/*
-	 * This thread doesn't need any user-level access,
-	 * so get rid of all our resources.
-	 */
-	daemonize("usb-storage");
 	current->flags |= PF_NOFREEZE;
-	unlock_kernel();
-
-	/* acquire a reference to the host, so it won't be deallocated
-	 * until we're ready to exit */
-	scsi_host_get(host);
-
-	/* signal that we've started the thread */
-	complete(&(us->notify));
 
 	for(;;) {
 		US_DEBUGP("*** thread sleeping.\n");
@@ -768,6 +754,7 @@ static int get_pipes(struct us_data *us)
 static int usb_stor_acquire_resources(struct us_data *us)
 {
 	int p;
+	struct task_struct *th;
 
 	us->current_urb = usb_alloc_urb(0, GFP_KERNEL);
 	if (!us->current_urb) {
@@ -784,17 +771,19 @@ static int usb_stor_acquire_resources(struct us_data *us)
 	}
 
 	/* Start up our control thread */
-	p = kernel_thread(usb_stor_control_thread, us, CLONE_VM);
-	if (p < 0) {
+	th = kthread_create(usb_stor_control_thread, us, "usb-storage");
+	if (IS_ERR(th)) {
 		printk(KERN_WARNING USB_STORAGE 
 		       "Unable to start control thread\n");
-		return p;
+		return PTR_ERR(th);
 	}
-	us->pid = p;
-	atomic_inc(&total_threads);
 
-	/* Wait for the thread to start */
-	wait_for_completion(&(us->notify));
+	/* Take a reference to the host for the control thread and
+	 * count it among all the threads we have launched.  Then
+	 * start it up. */
+	scsi_host_get(us_to_host(us));
+	atomic_inc(&total_threads);
+	wake_up_process(th);
 
 	return 0;
 }
@@ -890,21 +879,6 @@ static int usb_stor_scan_thread(void * __us)
 {
 	struct us_data *us = (struct us_data *)__us;
 
-	/*
-	 * This thread doesn't need any user-level access,
-	 * so get rid of all our resources.
-	 */
-	lock_kernel();
-	daemonize("usb-stor-scan");
-	unlock_kernel();
-
-	/* Acquire a reference to the host, so it won't be deallocated
-	 * until we're ready to exit */
-	scsi_host_get(us_to_host(us));
-
-	/* Signal that we've started the thread */
-	complete(&(us->notify));
-
 	printk(KERN_DEBUG
 		"usb-storage: device found at %d\n", us->pusb_dev->devnum);
 
@@ -949,6 +923,7 @@ static int storage_probe(struct usb_interface *intf,
 	struct us_data *us;
 	const int id_index = id - storage_usb_ids; 
 	int result;
+	struct task_struct *th;
 
 	US_DEBUGP("USB Mass Storage device detected\n");
 
@@ -1029,17 +1004,21 @@ static int storage_probe(struct usb_interface *intf,
 	}
 
 	/* Start up the thread for delayed SCSI-device scanning */
-	result = kernel_thread(usb_stor_scan_thread, us, CLONE_VM);
-	if (result < 0) {
+	th = kthread_create(usb_stor_scan_thread, us, "usb-stor-scan");
+	if (IS_ERR(th)) {
 		printk(KERN_WARNING USB_STORAGE 
 		       "Unable to start the device-scanning thread\n");
 		quiesce_and_remove_host(us);
+		result = PTR_ERR(th);
 		goto BadDevice;
 	}
-	atomic_inc(&total_threads);
 
-	/* Wait for the thread to start */
-	wait_for_completion(&(us->notify));
+	/* Take a reference to the host for the scanning thread and
+	 * count it among all the threads we have launched.  Then
+	 * start it up. */
+	scsi_host_get(us_to_host(us));
+	atomic_inc(&total_threads);
+	wake_up_process(th);
 
 	return 0;
 
diff --git a/drivers/usb/storage/usb.h b/drivers/usb/storage/usb.h
index dfa4dc7..98b0971 100644
--- a/drivers/usb/storage/usb.h
+++ b/drivers/usb/storage/usb.h
@@ -161,9 +161,6 @@ struct us_data {
 	struct scsi_cmnd	*srb;		 /* current srb		*/
 	unsigned int		tag;		 /* current dCBWTag	*/
 
-	/* thread information */
-	int			pid;		 /* control thread	 */
-
 	/* control and bulk communications data */
 	struct urb		*current_urb;	 /* USB requests	 */
 	struct usb_ctrlrequest	*cr;		 /* control requests	 */
-- 
cgit v1.1


From 72129cd6577793408ff546b0ddd5794c33f32399 Mon Sep 17 00:00:00 2001
From: Alexey Dobriyan <adobriyan@gmail.com>
Date: Tue, 25 Oct 2005 23:34:03 +0400
Subject: [PATCH] mdc800: remove embrions of C++ exceptions

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/image/mdc800.c | 30 +++++++++++++++++++++---------
 1 file changed, 21 insertions(+), 9 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/image/mdc800.c b/drivers/usb/image/mdc800.c
index e4ec133..1d973bc 100644
--- a/drivers/usb/image/mdc800.c
+++ b/drivers/usb/image/mdc800.c
@@ -975,13 +975,13 @@ static struct usb_driver mdc800_usb_driver =
 	Init and Cleanup this driver (Main Functions)
 *************************************************************************/
 
-#define try(A)           if (!(A)) goto cleanup_on_fail;
-
 static int __init usb_mdc800_init (void)
 {
 	int retval = -ENODEV;
 	/* Allocate Memory */
-	try (mdc800=kmalloc (sizeof (struct mdc800_data), GFP_KERNEL));
+	mdc800=kmalloc (sizeof (struct mdc800_data), GFP_KERNEL);
+	if (!mdc800)
+		goto cleanup_on_fail;
 
 	memset(mdc800, 0, sizeof(struct mdc800_data));
 	mdc800->dev = NULL;
@@ -997,13 +997,25 @@ static int __init usb_mdc800_init (void)
 	mdc800->downloaded = 0;
 	mdc800->written = 0;
 
-	try (mdc800->irq_urb_buffer=kmalloc (8, GFP_KERNEL));
-	try (mdc800->write_urb_buffer=kmalloc (8, GFP_KERNEL));
-	try (mdc800->download_urb_buffer=kmalloc (64, GFP_KERNEL));
+	mdc800->irq_urb_buffer=kmalloc (8, GFP_KERNEL);
+	if (!mdc800->irq_urb_buffer)
+		goto cleanup_on_fail;
+	mdc800->write_urb_buffer=kmalloc (8, GFP_KERNEL);
+	if (!mdc800->write_urb_buffer)
+		goto cleanup_on_fail;
+	mdc800->download_urb_buffer=kmalloc (64, GFP_KERNEL);
+	if (!mdc800->download_urb_buffer)
+		goto cleanup_on_fail;
 
-	try (mdc800->irq_urb=usb_alloc_urb (0, GFP_KERNEL));
-	try (mdc800->download_urb=usb_alloc_urb (0, GFP_KERNEL));
-	try (mdc800->write_urb=usb_alloc_urb (0, GFP_KERNEL));
+	mdc800->irq_urb=usb_alloc_urb (0, GFP_KERNEL);
+	if (!mdc800->irq_urb)
+		goto cleanup_on_fail;
+	mdc800->download_urb=usb_alloc_urb (0, GFP_KERNEL);
+	if (!mdc800->download_urb)
+		goto cleanup_on_fail;
+	mdc800->write_urb=usb_alloc_urb (0, GFP_KERNEL);
+	if (!mdc800->write_urb)
+		goto cleanup_on_fail;
 
 	/* Register the driver */
 	retval = usb_register(&mdc800_usb_driver);
-- 
cgit v1.1


From e52783206ada0c0276c8dd74c0ecd0007ead7c00 Mon Sep 17 00:00:00 2001
From: Phil Dibowitz <phil@ipom.com>
Date: Sun, 23 Oct 2005 23:52:39 -0700
Subject: [PATCH] USB Storage: Expand range of Freecom unusual_devs entry

Freecom seems to be one of those vendors that can't get the GET CAPACITY
thing right. This expands the US_FL_FIX_CAPACITY flag for the entire
range of their fccd product line.

This is based on a patch sent by Stuart Black
<stuart_black@yahoo.co.uk>.

Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/storage/unusual_devs.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers')

diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h
index d0f6a7e..9e926a8 100644
--- a/drivers/usb/storage/unusual_devs.h
+++ b/drivers/usb/storage/unusual_devs.h
@@ -756,7 +756,7 @@ UNUSUAL_DEV(  0x07ab, 0xfc01, 0x0000, 0x9999,
 #endif
 
 /* Reported by Eero Volotinen <eero@ping-viini.org> */
-UNUSUAL_DEV(  0x07ab, 0xfccd, 0x0406, 0x0406,
+UNUSUAL_DEV(  0x07ab, 0xfccd, 0x0000, 0x9999,
 		"Freecom Technologies",
 		"FHD-Classic",
 		US_SC_DEVICE, US_PR_DEVICE, NULL,
-- 
cgit v1.1


From be69e5b1900a19a545becda822b18d6f09168ba5 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Tue, 25 Oct 2005 15:56:06 -0400
Subject: [PATCH] usbcore: Improve endpoint sysfs file handling

This revised patch (as587b) improves the implementation of USB endpoint
sysfs files.  Instead of storing a whole bunch of attributes for every
single endpoint, each endpoint now gets its own kobject and they can
share a static list of attributes.  The number of extra fields added to
struct usb_host_endpoint has been reduced from 4 to 1.

The bEndpointAddress field is retained even though it is redundant (it
repeats the same information as the attributes' directory name).  The
code avoids calling kobject_register, to prevent generating unwanted
hotplug events.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/sysfs.c | 219 +++++++++++++++++++++++++++--------------------
 1 file changed, 124 insertions(+), 95 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/sysfs.c b/drivers/usb/core/sysfs.c
index 4bdbc9d..f18317f 100644
--- a/drivers/usb/core/sysfs.c
+++ b/drivers/usb/core/sysfs.c
@@ -23,43 +23,56 @@
 #include "usb.h"
 
 /* endpoint stuff */
-struct endpoint_attribute {
-	struct device_attribute dev_attr;
-	struct usb_endpoint_descriptor *endpoint;
+struct ep_object {
+	struct usb_endpoint_descriptor *desc;
 	struct usb_device *udev;
+	struct kobject kobj;
 };
-#define to_endpoint_attr(_dev_attr) \
-	container_of(_dev_attr, struct endpoint_attribute, dev_attr)
-
-#define usb_ep_attr(field, format_string)					\
-static ssize_t show_ep_##field(struct device *dev, struct device_attribute *attr,	\
-			    char *buf)						\
-{										\
-	struct endpoint_attribute *endpoint_attr = to_endpoint_attr(attr);	\
-										\
-	return sprintf(buf, format_string, endpoint_attr->endpoint->field);	\
-}
+#define to_ep_object(_kobj) \
+	container_of(_kobj, struct ep_object, kobj)
+
+struct ep_attribute {
+	struct attribute attr;
+	ssize_t (*show)(struct usb_device *,
+			struct usb_endpoint_descriptor *, char *);
+};
+#define to_ep_attribute(_attr) \
+	container_of(_attr, struct ep_attribute, attr)
+
+#define EP_ATTR(_name)						\
+struct ep_attribute ep_##_name = {				\
+	.attr = {.name = #_name, .owner = THIS_MODULE,		\
+			.mode = S_IRUGO},			\
+	.show = show_ep_##_name}
+
+#define usb_ep_attr(field, format_string)			\
+static ssize_t show_ep_##field(struct usb_device *udev,		\
+		struct usb_endpoint_descriptor *desc, 		\
+		char *buf)					\
+{								\
+	return sprintf(buf, format_string, desc->field);	\
+}								\
+static EP_ATTR(field);
+
 usb_ep_attr(bLength, "%02x\n")
-usb_ep_attr(bDescriptorType, "%02x\n")
 usb_ep_attr(bEndpointAddress, "%02x\n")
 usb_ep_attr(bmAttributes, "%02x\n")
 usb_ep_attr(bInterval, "%02x\n")
 
-static ssize_t show_ep_wMaxPacketSize(struct device *dev,
-				      struct device_attribute *attr, char *buf)
+static ssize_t show_ep_wMaxPacketSize(struct usb_device *udev,
+		struct usb_endpoint_descriptor *desc, char *buf)
 {
-	struct endpoint_attribute *endpoint_attr = to_endpoint_attr(attr);
-
 	return sprintf(buf, "%04x\n",
-		      le16_to_cpu(endpoint_attr->endpoint->wMaxPacketSize) & 0x07ff);
+			le16_to_cpu(desc->wMaxPacketSize) & 0x07ff);
 }
+static EP_ATTR(wMaxPacketSize);
 
-static ssize_t show_ep_type(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_ep_type(struct usb_device *udev,
+		struct usb_endpoint_descriptor *desc, char *buf)
 {
-	struct endpoint_attribute *endpoint_attr = to_endpoint_attr(attr);
 	char *type = "unknown";
 
-	switch (endpoint_attr->endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) {
+	switch (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) {
 	case USB_ENDPOINT_XFER_CONTROL:
 		type = "Control";
 		break;
@@ -75,35 +88,34 @@ static ssize_t show_ep_type(struct device *dev, struct device_attribute *attr, c
 	}
 	return sprintf(buf, "%s\n", type);
 }
+static EP_ATTR(type);
 
-static ssize_t show_ep_interval(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_ep_interval(struct usb_device *udev,
+		struct usb_endpoint_descriptor *desc, char *buf)
 {
-	struct endpoint_attribute *endpoint_attr = to_endpoint_attr(attr);
-	struct usb_device *udev = endpoint_attr->udev;
-	struct usb_endpoint_descriptor *endpoint = endpoint_attr->endpoint;
 	char unit;
 	unsigned interval = 0;
 	unsigned in;
 
-	in = (endpoint->bEndpointAddress & USB_DIR_IN);
+	in = (desc->bEndpointAddress & USB_DIR_IN);
 
-	switch (endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) {
+	switch (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) {
 	case USB_ENDPOINT_XFER_CONTROL:
 		if (udev->speed == USB_SPEED_HIGH) 	/* uframes per NAK */
-			interval = endpoint->bInterval;
+			interval = desc->bInterval;
 		break;
 	case USB_ENDPOINT_XFER_ISOC:
-		interval = 1 << (endpoint->bInterval - 1);
+		interval = 1 << (desc->bInterval - 1);
 		break;
 	case USB_ENDPOINT_XFER_BULK:
-		if (udev->speed == USB_SPEED_HIGH && !in)	/* uframes per NAK */
-			interval = endpoint->bInterval;
+		if (udev->speed == USB_SPEED_HIGH && !in) /* uframes per NAK */
+			interval = desc->bInterval;
 		break;
 	case USB_ENDPOINT_XFER_INT:
-		if (udev->speed == USB_SPEED_HIGH) {
-			interval = 1 << (endpoint->bInterval - 1);
-		} else
-			interval = endpoint->bInterval;
+		if (udev->speed == USB_SPEED_HIGH)
+			interval = 1 << (desc->bInterval - 1);
+		else
+			interval = desc->bInterval;
 		break;
 	}
 	interval *= (udev->speed == USB_SPEED_HIGH) ? 125 : 1000;
@@ -116,78 +128,95 @@ static ssize_t show_ep_interval(struct device *dev, struct device_attribute *att
 
 	return sprintf(buf, "%d%cs\n", interval, unit);
 }
+static EP_ATTR(interval);
 
-static ssize_t show_ep_direction(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_ep_direction(struct usb_device *udev,
+		struct usb_endpoint_descriptor *desc, char *buf)
 {
-	struct endpoint_attribute *endpoint_attr = to_endpoint_attr(attr);
 	char *direction;
 
-	if ((endpoint_attr->endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
-	    USB_ENDPOINT_XFER_CONTROL)
+	if ((desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
+			USB_ENDPOINT_XFER_CONTROL)
 		direction = "both";
-	else if (endpoint_attr->endpoint->bEndpointAddress & USB_DIR_IN)
+	else if (desc->bEndpointAddress & USB_DIR_IN)
 		direction = "in";
 	else
 		direction = "out";
 	return sprintf(buf, "%s\n", direction);
 }
+static EP_ATTR(direction);
+
+static struct attribute *ep_attrs[] = {
+	&ep_bLength.attr,
+	&ep_bEndpointAddress.attr,
+	&ep_bmAttributes.attr,
+	&ep_bInterval.attr,
+	&ep_wMaxPacketSize.attr,
+	&ep_type.attr,
+	&ep_interval.attr,
+	&ep_direction.attr,
+	NULL,
+};
 
-static struct endpoint_attribute *create_ep_attr(struct usb_endpoint_descriptor *endpoint,
-						 struct usb_device *udev, char *name,
-		ssize_t (*show)(struct device *dev, struct device_attribute *attr, char *buf))
+static void ep_object_release(struct kobject *kobj)
 {
-	struct endpoint_attribute *ep_attr;
-
-	ep_attr = kzalloc(sizeof(*ep_attr), GFP_KERNEL);
-	if (ep_attr) {
-		ep_attr->endpoint = endpoint;
-		ep_attr->udev = udev;
-		ep_attr->dev_attr.attr.name = name;
-		ep_attr->dev_attr.attr.mode = 0444;
-		ep_attr->dev_attr.attr.owner = THIS_MODULE;
-		ep_attr->dev_attr.show = show;
-	}
-	return ep_attr;
+	kfree(to_ep_object(kobj));
 }
 
-static void usb_create_ep_files(struct kobject *kobj, struct usb_host_endpoint *endpoint, struct usb_device *udev)
+static ssize_t ep_object_show(struct kobject *kobj, struct attribute *attr,
+		char *buf)
 {
-	struct usb_endpoint_descriptor *ep;
-
-	ep = &endpoint->desc;
-
-	endpoint->attrs = kzalloc(sizeof(struct attribute *) * 10, GFP_KERNEL);
-	endpoint->attrs[0] = &(create_ep_attr(ep, udev, "direction", show_ep_direction)->dev_attr.attr);
-	endpoint->attrs[1] = &(create_ep_attr(ep, udev, "type", show_ep_type)->dev_attr.attr);
-	endpoint->attrs[2] = &(create_ep_attr(ep, udev, "bLength", show_ep_bLength)->dev_attr.attr);
-	endpoint->attrs[3] = &(create_ep_attr(ep, udev, "bDescriptorType", show_ep_bDescriptorType)->dev_attr.attr);
-	endpoint->attrs[4] = &(create_ep_attr(ep, udev, "bEndpointAddress", show_ep_bEndpointAddress)->dev_attr.attr);
-	endpoint->attrs[5] = &(create_ep_attr(ep, udev, "bmAttributes", show_ep_bmAttributes)->dev_attr.attr);
-	endpoint->attrs[6] = &(create_ep_attr(ep, udev, "wMaxPacketSize", show_ep_wMaxPacketSize)->dev_attr.attr);
-	endpoint->attrs[7] = &(create_ep_attr(ep, udev, "bInterval", show_ep_bInterval)->dev_attr.attr);
-	endpoint->attrs[8] = &(create_ep_attr(ep, udev, "interval", show_ep_interval)->dev_attr.attr);
-	endpoint->attrs[9] = NULL;
-	endpoint->num_attrs = 9;
-
-	endpoint->attr_group = kzalloc(sizeof(*endpoint->attr_group), GFP_KERNEL);
-	endpoint->attr_name = kzalloc(10, GFP_KERNEL);
-	sprintf(endpoint->attr_name, "ep_%02x", endpoint->desc.bEndpointAddress);
-
-	endpoint->attr_group->attrs = endpoint->attrs;
-	endpoint->attr_group->name = endpoint->attr_name;
-	sysfs_create_group(kobj, endpoint->attr_group);
+	struct ep_object *ep_obj = to_ep_object(kobj);
+	struct ep_attribute *ep_attr = to_ep_attribute(attr);
+
+	return (ep_attr->show)(ep_obj->udev, ep_obj->desc, buf);
 }
 
-static void usb_remove_ep_files(struct kobject *kobj, struct usb_host_endpoint *endpoint)
+static struct sysfs_ops ep_object_sysfs_ops = {
+	.show =			ep_object_show,
+};
+
+static struct kobj_type ep_object_ktype = {
+	.release =		ep_object_release,
+	.sysfs_ops =		&ep_object_sysfs_ops,
+	.default_attrs =	ep_attrs,
+};
+
+static void usb_create_ep_files(struct kobject *parent,
+		struct usb_host_endpoint *endpoint,
+		struct usb_device *udev)
 {
-	int i;
+	struct ep_object *ep_obj;
+	struct kobject *kobj;
+
+	ep_obj = kzalloc(sizeof(struct ep_object), GFP_KERNEL);
+	if (!ep_obj)
+		return;
 
-	sysfs_remove_group(kobj, endpoint->attr_group);
-	kfree(endpoint->attr_group);
-	kfree(endpoint->attr_name);
-	for (i = 0; i < endpoint->num_attrs; ++i)
-		kfree(endpoint->attrs[i]);
-	kfree(endpoint->attrs);
+	ep_obj->desc = &endpoint->desc;
+	ep_obj->udev = udev;
+
+	kobj = &ep_obj->kobj;
+	kobject_set_name(kobj, "ep_%02x", endpoint->desc.bEndpointAddress);
+	kobj->parent = parent;
+	kobj->ktype = &ep_object_ktype;
+
+	/* Don't use kobject_register, because it generates a hotplug event */
+	kobject_init(kobj);
+	if (kobject_add(kobj) == 0)
+		endpoint->kobj = kobj;
+	else
+		kobject_put(kobj);
+}
+
+static void usb_remove_ep_files(struct usb_host_endpoint *endpoint)
+{
+
+	if (endpoint->kobj) {
+		kobject_del(endpoint->kobj);
+		kobject_put(endpoint->kobj);
+		endpoint->kobj = NULL;
+	}
 }
 
 /* Active configuration fields */
@@ -411,7 +440,7 @@ void usb_remove_sysfs_dev_files (struct usb_device *udev)
 {
 	struct device *dev = &udev->dev;
 
-	usb_remove_ep_files(&dev->kobj, &udev->ep0);
+	usb_remove_ep_files(&udev->ep0);
 	sysfs_remove_group(&dev->kobj, &dev_attr_grp);
 
 	if (udev->descriptor.iManufacturer)
@@ -496,7 +525,7 @@ static struct attribute_group intf_attr_grp = {
 	.attrs = intf_attrs,
 };
 
-static void usb_create_intf_ep_files(struct usb_interface *intf)
+static inline void usb_create_intf_ep_files(struct usb_interface *intf)
 {
 	struct usb_host_interface *iface_desc;
 	int i;
@@ -504,17 +533,17 @@ static void usb_create_intf_ep_files(struct usb_interface *intf)
 	iface_desc = intf->cur_altsetting;
 	for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i)
 		usb_create_ep_files(&intf->dev.kobj, &iface_desc->endpoint[i],
-				    interface_to_usbdev(intf));
+				interface_to_usbdev(intf));
 }
 
-static void usb_remove_intf_ep_files(struct usb_interface *intf)
+static inline void usb_remove_intf_ep_files(struct usb_interface *intf)
 {
 	struct usb_host_interface *iface_desc;
 	int i;
 
 	iface_desc = intf->cur_altsetting;
 	for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i)
-		usb_remove_ep_files(&intf->dev.kobj, &iface_desc->endpoint[i]);
+		usb_remove_ep_files(&iface_desc->endpoint[i]);
 }
 
 void usb_create_sysfs_intf_files (struct usb_interface *intf)
-- 
cgit v1.1


From 0e6c8e8db508fcb292836b23d039649c5de29090 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Mon, 24 Oct 2005 15:33:03 -0400
Subject: [PATCH] usbcore: endpoint attributes track altsetting changes

This patch (as588) fixes the way endpoint attribute files are registered
and unregistered.  Now they will correctly track along with altsetting
changes.  This fixes bugzilla entry #5467.

In a separate but related change, when a usb_reset_configuration call
fails, the device state is not changed to USB_STATE_ADDRESS.  In the
first place, failure means that we don't know what the state is, not
that we know the device is unconfigured.  In the second place, doing
this can potentially lead to a memory leak, since usbcore might not
realize there still is a current configuration that needs to be
destroyed.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/message.c | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c
index 574d0d4..5ad0d5e 100644
--- a/drivers/usb/core/message.c
+++ b/drivers/usb/core/message.c
@@ -1149,6 +1149,8 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate)
 	 */
 
 	/* prevent submissions using previous endpoint settings */
+	if (device_is_registered(&iface->dev))
+		usb_remove_sysfs_intf_files(iface);
 	usb_disable_interface(dev, iface);
 
 	iface->cur_altsetting = alt;
@@ -1184,6 +1186,8 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate)
 	 * (Likewise, EP0 never "halts" on well designed devices.)
 	 */
 	usb_enable_interface(dev, iface);
+	if (device_is_registered(&iface->dev))
+		usb_create_sysfs_intf_files(iface);
 
 	return 0;
 }
@@ -1233,10 +1237,8 @@ int usb_reset_configuration(struct usb_device *dev)
 			USB_REQ_SET_CONFIGURATION, 0,
 			config->desc.bConfigurationValue, 0,
 			NULL, 0, USB_CTRL_SET_TIMEOUT);
-	if (retval < 0) {
-		usb_set_device_state(dev, USB_STATE_ADDRESS);
+	if (retval < 0)
 		return retval;
-	}
 
 	dev->toggle[0] = dev->toggle[1] = 0;
 
@@ -1245,6 +1247,8 @@ int usb_reset_configuration(struct usb_device *dev)
 		struct usb_interface *intf = config->interface[i];
 		struct usb_host_interface *alt;
 
+		if (device_is_registered(&intf->dev))
+			usb_remove_sysfs_intf_files(intf);
 		alt = usb_altnum_to_altsetting(intf, 0);
 
 		/* No altsetting 0?  We'll assume the first altsetting.
@@ -1257,6 +1261,8 @@ int usb_reset_configuration(struct usb_device *dev)
 
 		intf->cur_altsetting = alt;
 		usb_enable_interface(dev, intf);
+		if (device_is_registered(&intf->dev))
+			usb_create_sysfs_intf_files(intf);
 	}
 	return 0;
 }
-- 
cgit v1.1


From b724ae77969fd832be71419dca74bece9af287ff Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Mon, 24 Oct 2005 15:36:00 -0400
Subject: [PATCH] usbcore: Wrap lines before column 80

I can't stand text lines that wrap-around in my 80-column windows.  This
patch (as589) makes cosmetic changes to a couple of source files.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/sysfs.c | 30 ++++++++++++++++++++----------
 1 file changed, 20 insertions(+), 10 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/sysfs.c b/drivers/usb/core/sysfs.c
index f18317f..4cca77c 100644
--- a/drivers/usb/core/sysfs.c
+++ b/drivers/usb/core/sysfs.c
@@ -221,7 +221,8 @@ static void usb_remove_ep_files(struct usb_host_endpoint *endpoint)
 
 /* Active configuration fields */
 #define usb_actconfig_show(field, multiplier, format_string)		\
-static ssize_t  show_##field (struct device *dev, struct device_attribute *attr, char *buf)		\
+static ssize_t  show_##field (struct device *dev,			\
+		struct device_attribute *attr, char *buf)		\
 {									\
 	struct usb_device *udev;					\
 	struct usb_host_config *actconfig;				\
@@ -243,7 +244,8 @@ usb_actconfig_attr (bNumInterfaces, 1, "%2d\n")
 usb_actconfig_attr (bmAttributes, 1, "%2x\n")
 usb_actconfig_attr (bMaxPower, 2, "%3dmA\n")
 
-static ssize_t show_configuration_string(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_configuration_string(struct device *dev,
+		struct device_attribute *attr, char *buf)
 {
 	struct usb_device *udev;
 	struct usb_host_config *actconfig;
@@ -266,7 +268,8 @@ static DEVICE_ATTR(configuration, S_IRUGO, show_configuration_string, NULL);
 usb_actconfig_show(bConfigurationValue, 1, "%u\n");
 
 static ssize_t
-set_bConfigurationValue (struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
+set_bConfigurationValue (struct device *dev, struct device_attribute *attr,
+		const char *buf, size_t count)
 {
 	struct usb_device	*udev = udev = to_usb_device (dev);
 	int			config, value;
@@ -284,7 +287,8 @@ static DEVICE_ATTR(bConfigurationValue, S_IRUGO | S_IWUSR,
 
 /* String fields */
 #define usb_string_attr(name)						\
-static ssize_t  show_##name(struct device *dev, struct device_attribute *attr, char *buf)		\
+static ssize_t  show_##name(struct device *dev,				\
+		struct device_attribute *attr, char *buf)		\
 {									\
 	struct usb_device *udev;					\
 	int len;							\
@@ -364,7 +368,8 @@ static DEVICE_ATTR(maxchild, S_IRUGO, show_maxchild, NULL);
 /* Descriptor fields */
 #define usb_descriptor_attr_le16(field, format_string)			\
 static ssize_t								\
-show_##field (struct device *dev, struct device_attribute *attr, char *buf)				\
+show_##field (struct device *dev, struct device_attribute *attr,	\
+		char *buf)						\
 {									\
 	struct usb_device *udev;					\
 									\
@@ -380,7 +385,8 @@ usb_descriptor_attr_le16(bcdDevice, "%04x\n")
 
 #define usb_descriptor_attr(field, format_string)			\
 static ssize_t								\
-show_##field (struct device *dev, struct device_attribute *attr, char *buf)				\
+show_##field (struct device *dev, struct device_attribute *attr,	\
+		char *buf)						\
 {									\
 	struct usb_device *udev;					\
 									\
@@ -455,11 +461,13 @@ void usb_remove_sysfs_dev_files (struct usb_device *udev)
 /* Interface fields */
 #define usb_intf_attr(field, format_string)				\
 static ssize_t								\
-show_##field (struct device *dev, struct device_attribute *attr, char *buf)				\
+show_##field (struct device *dev, struct device_attribute *attr,	\
+		char *buf)						\
 {									\
 	struct usb_interface *intf = to_usb_interface (dev);		\
 									\
-	return sprintf (buf, format_string, intf->cur_altsetting->desc.field); \
+	return sprintf (buf, format_string,				\
+			intf->cur_altsetting->desc.field); 		\
 }									\
 static DEVICE_ATTR(field, S_IRUGO, show_##field, NULL);
 
@@ -470,7 +478,8 @@ usb_intf_attr (bInterfaceClass, "%02x\n")
 usb_intf_attr (bInterfaceSubClass, "%02x\n")
 usb_intf_attr (bInterfaceProtocol, "%02x\n")
 
-static ssize_t show_interface_string(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_interface_string(struct device *dev,
+		struct device_attribute *attr, char *buf)
 {
 	struct usb_interface *intf;
 	struct usb_device *udev;
@@ -487,7 +496,8 @@ static ssize_t show_interface_string(struct device *dev, struct device_attribute
 }
 static DEVICE_ATTR(interface, S_IRUGO, show_interface_string, NULL);
 
-static ssize_t show_modalias(struct device *dev, struct device_attribute *attr, char *buf)
+static ssize_t show_modalias(struct device *dev,
+		struct device_attribute *attr, char *buf)
 {
 	struct usb_interface *intf;
 	struct usb_device *udev;
-- 
cgit v1.1


From 0a1ef3b5a765a6f20e7b8caf295aad3276243966 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Mon, 24 Oct 2005 15:38:24 -0400
Subject: [PATCH] usbcore: Use kzalloc instead of kmalloc/memset

This patch (as590) fixes up all the remaining places where usbcore can
use kzalloc rather than kmalloc/memset.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/config.c  | 12 ++++--------
 drivers/usb/core/devio.c   |  4 ++--
 drivers/usb/core/hcd.c     |  3 +--
 drivers/usb/core/hub.c     |  4 +---
 drivers/usb/core/message.c |  3 +--
 drivers/usb/core/usb.c     |  4 +---
 6 files changed, 10 insertions(+), 20 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/config.c b/drivers/usb/core/config.c
index 99595e0..63f374e6 100644
--- a/drivers/usb/core/config.c
+++ b/drivers/usb/core/config.c
@@ -188,10 +188,9 @@ static int usb_parse_interface(struct device *ddev, int cfgno,
 	}
 
 	len = sizeof(struct usb_host_endpoint) * num_ep;
-	alt->endpoint = kmalloc(len, GFP_KERNEL);
+	alt->endpoint = kzalloc(len, GFP_KERNEL);
 	if (!alt->endpoint)
 		return -ENOMEM;
-	memset(alt->endpoint, 0, len);
 
 	/* Parse all the endpoint descriptors */
 	n = 0;
@@ -353,10 +352,9 @@ static int usb_parse_configuration(struct device *ddev, int cfgidx,
 		}
 
 		len = sizeof(*intfc) + sizeof(struct usb_host_interface) * j;
-		config->intf_cache[i] = intfc = kmalloc(len, GFP_KERNEL);
+		config->intf_cache[i] = intfc = kzalloc(len, GFP_KERNEL);
 		if (!intfc)
 			return -ENOMEM;
-		memset(intfc, 0, len);
 		kref_init(&intfc->ref);
 	}
 
@@ -459,16 +457,14 @@ int usb_get_configuration(struct usb_device *dev)
 	}
 
 	length = ncfg * sizeof(struct usb_host_config);
-	dev->config = kmalloc(length, GFP_KERNEL);
+	dev->config = kzalloc(length, GFP_KERNEL);
 	if (!dev->config)
 		goto err2;
-	memset(dev->config, 0, length);
 
 	length = ncfg * sizeof(char *);
-	dev->rawdescriptors = kmalloc(length, GFP_KERNEL);
+	dev->rawdescriptors = kzalloc(length, GFP_KERNEL);
 	if (!dev->rawdescriptors)
 		goto err2;
-	memset(dev->rawdescriptors, 0, length);
 
 	buffer = kmalloc(USB_DT_CONFIG_SIZE, GFP_KERNEL);
 	if (!buffer)
diff --git a/drivers/usb/core/devio.c b/drivers/usb/core/devio.c
index ffb2e24..942cd43 100644
--- a/drivers/usb/core/devio.c
+++ b/drivers/usb/core/devio.c
@@ -210,10 +210,10 @@ err:
 static struct async *alloc_async(unsigned int numisoframes)
 {
         unsigned int assize = sizeof(struct async) + numisoframes * sizeof(struct usb_iso_packet_descriptor);
-        struct async *as = kmalloc(assize, GFP_KERNEL);
+        struct async *as = kzalloc(assize, GFP_KERNEL);
+
         if (!as)
                 return NULL;
-        memset(as, 0, assize);
 	as->urb = usb_alloc_urb(numisoframes, GFP_KERNEL);
 	if (!as->urb) {
 		kfree(as);
diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index e8f2b8d..61ef994 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -744,10 +744,9 @@ struct usb_bus *usb_alloc_bus (struct usb_operations *op)
 {
 	struct usb_bus *bus;
 
-	bus = kmalloc (sizeof *bus, GFP_KERNEL);
+	bus = kzalloc (sizeof *bus, GFP_KERNEL);
 	if (!bus)
 		return NULL;
-	memset(bus, 0, sizeof(struct usb_bus));
 	usb_bus_init (bus);
 	bus->op = op;
 	return bus;
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 6a2ebd8..8ba5854 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -865,14 +865,12 @@ descriptor_error:
 	/* We found a hub */
 	dev_info (&intf->dev, "USB hub found\n");
 
-	hub = kmalloc(sizeof(*hub), GFP_KERNEL);
+	hub = kzalloc(sizeof(*hub), GFP_KERNEL);
 	if (!hub) {
 		dev_dbg (&intf->dev, "couldn't kmalloc hub struct\n");
 		return -ENOMEM;
 	}
 
-	memset(hub, 0, sizeof(*hub));
-
 	INIT_LIST_HEAD(&hub->event_list);
 	hub->intfdev = &intf->dev;
 	hub->hdev = hdev;
diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c
index 5ad0d5e..3519f31 100644
--- a/drivers/usb/core/message.c
+++ b/drivers/usb/core/message.c
@@ -1350,7 +1350,7 @@ int usb_set_configuration(struct usb_device *dev, int configuration)
 		}
 
 		for (; n < nintf; ++n) {
-			new_interfaces[n] = kmalloc(
+			new_interfaces[n] = kzalloc(
 					sizeof(struct usb_interface),
 					GFP_KERNEL);
 			if (!new_interfaces[n]) {
@@ -1391,7 +1391,6 @@ free_interfaces:
 			struct usb_host_interface *alt;
 
 			cp->interface[i] = intf = new_interfaces[i];
-			memset(intf, 0, sizeof(*intf));
 			intfc = cp->intf_cache[i];
 			intf->altsetting = intfc->altsetting;
 			intf->num_altsetting = intfc->num_altsetting;
diff --git a/drivers/usb/core/usb.c b/drivers/usb/core/usb.c
index 4eca490..0eefff7 100644
--- a/drivers/usb/core/usb.c
+++ b/drivers/usb/core/usb.c
@@ -704,12 +704,10 @@ usb_alloc_dev(struct usb_device *parent, struct usb_bus *bus, unsigned port1)
 {
 	struct usb_device *dev;
 
-	dev = kmalloc(sizeof(*dev), GFP_KERNEL);
+	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
 	if (!dev)
 		return NULL;
 
-	memset(dev, 0, sizeof(*dev));
-
 	bus = usb_bus_get(bus);
 	if (!bus) {
 		kfree(dev);
-- 
cgit v1.1


From 16f16d117c1eb99451e4c73c87546eef05c66790 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Mon, 24 Oct 2005 15:41:19 -0400
Subject: [PATCH] USB: Fix maxpacket length for ep0 on root hubs

This patch (as591) fixes a rather innocuous bug that has been around for
quite a long time: Virtual root hubs should have a maxpacket length of
64 for endpoint 0.  I didn't realize it was wrong until I started
looking through the endpoint attribute files.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/hcd.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 61ef994..6c7ca5b 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -130,7 +130,7 @@ static const u8 usb2_rh_dev_descriptor [18] = {
 	0x09,	    /*  __u8  bDeviceClass; HUB_CLASSCODE */
 	0x00,	    /*  __u8  bDeviceSubClass; */
 	0x01,       /*  __u8  bDeviceProtocol; [ usb 2.0 single TT ]*/
-	0x08,       /*  __u8  bMaxPacketSize0; 8 Bytes */
+	0x40,       /*  __u8  bMaxPacketSize0; 64 Bytes */
 
 	0x00, 0x00, /*  __le16 idVendor; */
  	0x00, 0x00, /*  __le16 idProduct; */
@@ -153,7 +153,7 @@ static const u8 usb11_rh_dev_descriptor [18] = {
 	0x09,	    /*  __u8  bDeviceClass; HUB_CLASSCODE */
 	0x00,	    /*  __u8  bDeviceSubClass; */
 	0x00,       /*  __u8  bDeviceProtocol; [ low/full speeds only ] */
-	0x08,       /*  __u8  bMaxPacketSize0; 8 Bytes */
+	0x40,       /*  __u8  bMaxPacketSize0; 64 Bytes */
 
 	0x00, 0x00, /*  __le16 idVendor; */
  	0x00, 0x00, /*  __le16 idProduct; */
-- 
cgit v1.1


From 4f62efe67f077db17dad03a1d4c9665000a3eb45 Mon Sep 17 00:00:00 2001
From: Alan Stern <stern@rowland.harvard.edu>
Date: Mon, 24 Oct 2005 16:24:14 -0400
Subject: [PATCH] usbcore: Fix handling of sysfs strings and other attributes

This patch (as592) makes a few small improvements to the way device
strings are handled, and it fixes some bugs in a couple of other sysfs
attribute routines.  (Look at show_configuration_string() to see what I
mean.)

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/config.c  | 10 ++++++----
 drivers/usb/core/hub.c     | 22 ++++-----------------
 drivers/usb/core/message.c | 48 +++++++++++++++++++++++++++++-----------------
 drivers/usb/core/sysfs.c   | 36 +++++++++++++++-------------------
 drivers/usb/core/usb.h     |  1 +
 5 files changed, 56 insertions(+), 61 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/config.c b/drivers/usb/core/config.c
index 63f374e6..9930195 100644
--- a/drivers/usb/core/config.c
+++ b/drivers/usb/core/config.c
@@ -112,8 +112,12 @@ void usb_release_interface_cache(struct kref *ref)
 	struct usb_interface_cache *intfc = ref_to_usb_interface_cache(ref);
 	int j;
 
-	for (j = 0; j < intfc->num_altsetting; j++)
-		kfree(intfc->altsetting[j].endpoint);
+	for (j = 0; j < intfc->num_altsetting; j++) {
+		struct usb_host_interface *alt = &intfc->altsetting[j];
+
+		kfree(alt->endpoint);
+		kfree(alt->string);
+	}
 	kfree(intfc);
 }
 
@@ -420,8 +424,6 @@ void usb_destroy_configuration(struct usb_device *dev)
 		struct usb_host_config *cf = &dev->config[c];
 
 		kfree(cf->string);
-		cf->string = NULL;
-
 		for (i = 0; i < cf->desc.bNumInterfaces; i++) {
 			if (cf->intf_cache[i])
 				kref_put(&cf->intf_cache[i]->ref, 
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 8ba5854..1bacb37 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1204,21 +1204,6 @@ static inline void show_string(struct usb_device *udev, char *id, char *string)
 {}
 #endif
 
-static void get_string(struct usb_device *udev, char **string, int index)
-{
-	char *buf;
-
-	if (!index)
-		return;
-	buf = kmalloc(256, GFP_KERNEL);
-	if (!buf)
-		return;
-	if (usb_string(udev, index, buf, 256) > 0)
-		*string = buf;
-	else
-		kfree(buf);
-}
-
 
 #ifdef	CONFIG_USB_OTG
 #include "otg_whitelist.h"
@@ -1257,9 +1242,10 @@ int usb_new_device(struct usb_device *udev)
 	}
 
 	/* read the standard strings and cache them if present */
-	get_string(udev, &udev->product, udev->descriptor.iProduct);
-	get_string(udev, &udev->manufacturer, udev->descriptor.iManufacturer);
-	get_string(udev, &udev->serial, udev->descriptor.iSerialNumber);
+	udev->product = usb_cache_string(udev, udev->descriptor.iProduct);
+	udev->manufacturer = usb_cache_string(udev,
+			udev->descriptor.iManufacturer);
+	udev->serial = usb_cache_string(udev, udev->descriptor.iSerialNumber);
 
 	/* Tell the world! */
 	dev_dbg(&udev->dev, "new device strings: Mfr=%d, Product=%d, "
diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c
index 3519f31..644a3d4 100644
--- a/drivers/usb/core/message.c
+++ b/drivers/usb/core/message.c
@@ -787,6 +787,31 @@ int usb_string(struct usb_device *dev, int index, char *buf, size_t size)
 	return err;
 }
 
+/**
+ * usb_cache_string - read a string descriptor and cache it for later use
+ * @udev: the device whose string descriptor is being read
+ * @index: the descriptor index
+ *
+ * Returns a pointer to a kmalloc'ed buffer containing the descriptor string,
+ * or NULL if the index is 0 or the string could not be read.
+ */
+char *usb_cache_string(struct usb_device *udev, int index)
+{
+	char *buf;
+	char *smallbuf = NULL;
+	int len;
+
+	if (index > 0 && (buf = kmalloc(256, GFP_KERNEL)) != NULL) {
+		if ((len = usb_string(udev, index, buf, 256)) > 0) {
+			if ((smallbuf = kmalloc(++len, GFP_KERNEL)) == NULL)
+				return buf;
+			memcpy(smallbuf, buf, len);
+		}
+		kfree(buf);
+	}
+	return smallbuf;
+}
+
 /*
  * usb_get_device_descriptor - (re)reads the device descriptor (usbcore)
  * @dev: the device whose device descriptor is being updated
@@ -1008,8 +1033,6 @@ void usb_disable_device(struct usb_device *dev, int skip_ep0)
 			dev_dbg (&dev->dev, "unregistering interface %s\n",
 				interface->dev.bus_id);
 			usb_remove_sysfs_intf_files(interface);
-			kfree(interface->cur_altsetting->string);
-			interface->cur_altsetting->string = NULL;
 			device_del (&interface->dev);
 		}
 
@@ -1422,12 +1445,9 @@ free_interfaces:
 		}
 		kfree(new_interfaces);
 
-		if ((cp->desc.iConfiguration) &&
-		    (cp->string == NULL)) {
-			cp->string = kmalloc(256, GFP_KERNEL);
-			if (cp->string)
-				usb_string(dev, cp->desc.iConfiguration, cp->string, 256);
-		}
+		if (cp->string == NULL)
+			cp->string = usb_cache_string(dev,
+					cp->desc.iConfiguration);
 
 		/* Now that all the interfaces are set up, register them
 		 * to trigger binding of drivers to interfaces.  probe()
@@ -1437,13 +1457,12 @@ free_interfaces:
 		 */
 		for (i = 0; i < nintf; ++i) {
 			struct usb_interface *intf = cp->interface[i];
-			struct usb_interface_descriptor *desc;
+			struct usb_host_interface *alt = intf->cur_altsetting;
 
-			desc = &intf->altsetting [0].desc;
 			dev_dbg (&dev->dev,
 				"adding %s (config #%d, interface %d)\n",
 				intf->dev.bus_id, configuration,
-				desc->bInterfaceNumber);
+				alt->desc.bInterfaceNumber);
 			ret = device_add (&intf->dev);
 			if (ret != 0) {
 				dev_err(&dev->dev,
@@ -1452,13 +1471,6 @@ free_interfaces:
 					ret);
 				continue;
 			}
-			if ((intf->cur_altsetting->desc.iInterface) &&
-			    (intf->cur_altsetting->string == NULL)) {
-				intf->cur_altsetting->string = kmalloc(256, GFP_KERNEL);
-				if (intf->cur_altsetting->string)
-					usb_string(dev, intf->cur_altsetting->desc.iInterface,
-						   intf->cur_altsetting->string, 256);
-			}
 			usb_create_sysfs_intf_files (intf);
 		}
 	}
diff --git a/drivers/usb/core/sysfs.c b/drivers/usb/core/sysfs.c
index 4cca77c..edd83e0 100644
--- a/drivers/usb/core/sysfs.c
+++ b/drivers/usb/core/sysfs.c
@@ -249,18 +249,12 @@ static ssize_t show_configuration_string(struct device *dev,
 {
 	struct usb_device *udev;
 	struct usb_host_config *actconfig;
-	int len;
 
 	udev = to_usb_device (dev);
 	actconfig = udev->actconfig;
 	if ((!actconfig) || (!actconfig->string))
 		return 0;
-	len = sprintf(buf, actconfig->string, PAGE_SIZE);
-	if (len < 0)
-		return 0;
-	buf[len] = '\n';
-	buf[len+1] = 0;
-	return len+1;
+	return sprintf(buf, "%s\n", actconfig->string);
 }
 static DEVICE_ATTR(configuration, S_IRUGO, show_configuration_string, NULL);
 
@@ -291,15 +285,9 @@ static ssize_t  show_##name(struct device *dev,				\
 		struct device_attribute *attr, char *buf)		\
 {									\
 	struct usb_device *udev;					\
-	int len;							\
 									\
 	udev = to_usb_device (dev);					\
-	len = snprintf(buf, 256, "%s", udev->name);			\
-	if (len < 0)							\
-		return 0;						\
-	buf[len] = '\n';						\
-	buf[len+1] = 0;							\
-	return len+1;							\
+	return sprintf(buf, "%s\n", udev->name);			\
 }									\
 static DEVICE_ATTR(name, S_IRUGO, show_##name, NULL);
 
@@ -449,11 +437,11 @@ void usb_remove_sysfs_dev_files (struct usb_device *udev)
 	usb_remove_ep_files(&udev->ep0);
 	sysfs_remove_group(&dev->kobj, &dev_attr_grp);
 
-	if (udev->descriptor.iManufacturer)
+	if (udev->manufacturer)
 		device_remove_file(dev, &dev_attr_manufacturer);
-	if (udev->descriptor.iProduct)
+	if (udev->product)
 		device_remove_file(dev, &dev_attr_product);
-	if (udev->descriptor.iSerialNumber)
+	if (udev->serial)
 		device_remove_file(dev, &dev_attr_serial);
 	device_remove_file (dev, &dev_attr_configuration);
 }
@@ -535,7 +523,8 @@ static struct attribute_group intf_attr_grp = {
 	.attrs = intf_attrs,
 };
 
-static inline void usb_create_intf_ep_files(struct usb_interface *intf)
+static inline void usb_create_intf_ep_files(struct usb_interface *intf,
+		struct usb_device *udev)
 {
 	struct usb_host_interface *iface_desc;
 	int i;
@@ -543,7 +532,7 @@ static inline void usb_create_intf_ep_files(struct usb_interface *intf)
 	iface_desc = intf->cur_altsetting;
 	for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i)
 		usb_create_ep_files(&intf->dev.kobj, &iface_desc->endpoint[i],
-				interface_to_usbdev(intf));
+				udev);
 }
 
 static inline void usb_remove_intf_ep_files(struct usb_interface *intf)
@@ -558,11 +547,16 @@ static inline void usb_remove_intf_ep_files(struct usb_interface *intf)
 
 void usb_create_sysfs_intf_files (struct usb_interface *intf)
 {
+	struct usb_device *udev = interface_to_usbdev(intf);
+	struct usb_host_interface *alt = intf->cur_altsetting;
+
 	sysfs_create_group(&intf->dev.kobj, &intf_attr_grp);
 
-	if (intf->cur_altsetting->string)
+	if (alt->string == NULL)
+		alt->string = usb_cache_string(udev, alt->desc.iInterface);
+	if (alt->string)
 		device_create_file(&intf->dev, &dev_attr_interface);
-	usb_create_intf_ep_files(intf);
+	usb_create_intf_ep_files(intf, udev);
 }
 
 void usb_remove_sysfs_intf_files (struct usb_interface *intf)
diff --git a/drivers/usb/core/usb.h b/drivers/usb/core/usb.h
index 888dbe4..1c4a684 100644
--- a/drivers/usb/core/usb.h
+++ b/drivers/usb/core/usb.h
@@ -13,6 +13,7 @@ extern void usb_disable_device (struct usb_device *dev, int skip_ep0);
 
 extern int usb_get_device_descriptor(struct usb_device *dev,
 		unsigned int size);
+extern char *usb_cache_string(struct usb_device *udev, int index);
 extern int usb_set_configuration(struct usb_device *dev, int configuration);
 
 extern void usb_lock_all_devices(void);
-- 
cgit v1.1


From db2d55b7f7f11823b8d2e5f0c706c7a264320d1b Mon Sep 17 00:00:00 2001
From: Andrew Morton <akpm@osdl.org>
Date: Sun, 23 Oct 2005 23:04:25 -0700
Subject: [PATCH] USB: fix pm patches with CONFIG_PM off part 1

With CONFIG_PM=n:

drivers/built-in.o(.text+0x2a69c): In function `ohci_hub_control':
drivers/usb/host/ohci-hub.c:539: undefined reference to `.usb_hcd_resume_root_hub'
drivers/built-in.o(.text+0x2b920): In function `ohci_irq':
drivers/usb/host/ohci-hcd.c:726: undefined reference to `.usb_hcd_resume_root_hub'

Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/hcd.h | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hcd.h b/drivers/usb/core/hcd.h
index a5d9294..24a62a2 100644
--- a/drivers/usb/core/hcd.h
+++ b/drivers/usb/core/hcd.h
@@ -351,9 +351,6 @@ extern long usb_calc_bus_time (int speed, int is_input,
 
 extern struct usb_bus *usb_alloc_bus (struct usb_operations *);
 
-extern void usb_hcd_suspend_root_hub (struct usb_hcd *hcd);
-extern void usb_hcd_resume_root_hub (struct usb_hcd *hcd);
-
 extern void usb_set_device_state(struct usb_device *udev,
 		enum usb_device_state new_state);
 
@@ -376,9 +373,21 @@ extern int usb_find_interface_driver (struct usb_device *dev,
 #define usb_endpoint_out(ep_dir)	(!((ep_dir) & USB_DIR_IN))
 
 #ifdef CONFIG_PM
+extern void usb_hcd_suspend_root_hub (struct usb_hcd *hcd);
+extern void usb_hcd_resume_root_hub (struct usb_hcd *hcd);
 extern int hcd_bus_suspend (struct usb_bus *bus);
 extern int hcd_bus_resume (struct usb_bus *bus);
 #else
+static inline void usb_hcd_suspend_root_hub(struct usb_hcd *hcd)
+{
+	return;
+}
+
+static inline void usb_hcd_resume_root_hub(struct usb_hcd *hcd)
+{
+	return;
+}
+
 static inline int hcd_bus_suspend(struct usb_bus *bus)
 {
 	return 0;
-- 
cgit v1.1


From 9a7834d06d553d02cc6e659e94772f69a8b5367f Mon Sep 17 00:00:00 2001
From: Andrew Morton <akpm@osdl.org>
Date: Sun, 23 Oct 2005 23:02:20 -0700
Subject: [PATCH] USB: fix pm patches with CONFIG_PM off part 2

With CONFIG_PM=n:

drivers/built-in.o(.text+0x1098c): In function `hub_thread':
drivers/usb/core/hub.c:2673: undefined reference to `.dpm_runtime_resume'
drivers/built-in.o(.text+0x10998):drivers/usb/core/hub.c:2674: undefined reference to `.dpm_runtime_resume'

Please, never ever ever put extern decls into .c files.  Use the darn header
files :(

Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/base/power/power.h | 13 -------------
 drivers/usb/core/hub.c     |  2 --
 2 files changed, 15 deletions(-)

(limited to 'drivers')

diff --git a/drivers/base/power/power.h b/drivers/base/power/power.h
index 2e700d7..fb3d35a 100644
--- a/drivers/base/power/power.h
+++ b/drivers/base/power/power.h
@@ -67,9 +67,6 @@ extern int suspend_device(struct device *, pm_message_t);
  * runtime.c
  */
 
-extern int dpm_runtime_suspend(struct device *, pm_message_t);
-extern void dpm_runtime_resume(struct device *);
-
 #else /* CONFIG_PM */
 
 
@@ -82,14 +79,4 @@ static inline void device_pm_remove(struct device * dev)
 
 }
 
-static inline int dpm_runtime_suspend(struct device * dev, pm_message_t state)
-{
-	return 0;
-}
-
-static inline void dpm_runtime_resume(struct device * dev)
-{
-
-}
-
 #endif
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 1bacb37..9660a89 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -2652,8 +2652,6 @@ static void hub_events(void)
 		 * stub "device" node was never suspended.
 		 */
 		if (i) {
-			extern void dpm_runtime_resume(struct device *);
-
 			dpm_runtime_resume(&hdev->dev);
 			dpm_runtime_resume(&intf->dev);
 		}
-- 
cgit v1.1


From 46a0cf81828535fb3c200bc4fffdb8d69f4bf396 Mon Sep 17 00:00:00 2001
From: Koen Kooi <koen@handhelds.org>
Date: Wed, 26 Oct 2005 19:42:53 +0200
Subject: [PATCH] USB: fix correct wording in drivers/usb/net/KConfig

Signed-off-by: Koen Kooi <koen@handhelds.org>
---
 drivers/usb/net/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers')

diff --git a/drivers/usb/net/Kconfig b/drivers/usb/net/Kconfig
index 8c010bb..efd6ca7 100644
--- a/drivers/usb/net/Kconfig
+++ b/drivers/usb/net/Kconfig
@@ -294,7 +294,7 @@ config USB_NET_ZAURUS
 	  This also supports some related device firmware, as used in some
 	  PDAs from Olympus and some cell phones from Motorola.
 
-	  If you install an alternate ROM image, such as the Linux 2.6 based
+	  If you install an alternate image, such as the Linux 2.6 based
 	  versions of OpenZaurus, you should no longer need to support this
 	  protocol.  Only the "eth-fd" or "net_fd" drivers in these devices
 	  really need this non-conformant variant of CDC Ethernet (or in
-- 
cgit v1.1


From bde621854f1958a6000834c7c089b528118e5a9a Mon Sep 17 00:00:00 2001
From: Martin Hagelin <martin@hagelin.dyndns.org>
Date: Wed, 26 Oct 2005 21:10:41 +0200
Subject: [PATCH] USB: add new device id to ftdi_sio module

This is a patch to get the ELV FHZ1000 Home Automation control device to
work with Linux. The patch adds a new device ID to the ftdi_sio driver.
It is for kernel version 2.6.13.4.

Signed-off-by: Martin Hagelin <martin.hagelin@home.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/ftdi_sio.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

(limited to 'drivers')

diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 77d54ac..61204bf 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -412,6 +412,7 @@ static struct usb_device_id id_table_combined [] = {
 	{ USB_DEVICE(FTDI_VID, FTDI_ELV_UR100_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_ELV_ALC8500_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_PYRAMID_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_ELV_FHZ1000PC_PID) },
 	/*
 	 * These will probably use user-space drivers.  Uncomment them if
 	 * you need them or use the user-specified vendor/product module
@@ -429,7 +430,6 @@ static struct usb_device_id id_table_combined [] = {
 	/* { USB_DEVICE(FTDI_VID, FTDI_ELV_T1100_PID) }, */
 	/* { USB_DEVICE(FTDI_VID, FTDI_ELV_PCD200_PID) }, */
 	/* { USB_DEVICE(FTDI_VID, FTDI_ELV_ULA200_PID) }, */
-	/* { USB_DEVICE(FTDI_VID, FTDI_ELV_FHZ1000PC_PID) }, */
 	/* { USB_DEVICE(FTDI_VID, FTDI_ELV_CSI8_PID) }, */
 	/* { USB_DEVICE(FTDI_VID, FTDI_ELV_EM1000DL_PID) }, */
 	/* { USB_DEVICE(FTDI_VID, FTDI_ELV_PCK100_PID) }, */
-- 
cgit v1.1


From 50260b69bbec383058875de26dbde28b1a6f8d00 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Mon, 20 Jun 2005 21:15:16 -0700
Subject: [PATCH] USB: add nokia_dku2 driver

This driver comes from the gnokii project.
Was further cleaned up by me to match recent usb-serial core changes.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/serial/Kconfig      |   9 +++
 drivers/usb/serial/Makefile     |   1 +
 drivers/usb/serial/nokia_dku2.c | 142 ++++++++++++++++++++++++++++++++++++++++
 3 files changed, 152 insertions(+)
 create mode 100644 drivers/usb/serial/nokia_dku2.c

(limited to 'drivers')

diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
index 9438909..7b5e8e4 100644
--- a/drivers/usb/serial/Kconfig
+++ b/drivers/usb/serial/Kconfig
@@ -394,6 +394,15 @@ config USB_SERIAL_MCT_U232
 	  To compile this driver as a module, choose M here: the
 	  module will be called mct_u232.
 
+config USB_SERIAL_NOKIA_DKU2
+	tristate "USB Nokia DKU2 Driver"
+	depends on USB_SERIAL
+	help
+	  Say Y here if you want to use a Nokia DKU2 device.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called nokia_dku2.
+
 config USB_SERIAL_PL2303
 	tristate "USB Prolific 2303 Single Port Serial Driver"
 	depends on USB_SERIAL
diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
index 6c7cdcc..55fd461 100644
--- a/drivers/usb/serial/Makefile
+++ b/drivers/usb/serial/Makefile
@@ -31,6 +31,7 @@ obj-$(CONFIG_USB_SERIAL_KEYSPAN_PDA)		+= keyspan_pda.o
 obj-$(CONFIG_USB_SERIAL_KLSI)			+= kl5kusb105.o
 obj-$(CONFIG_USB_SERIAL_KOBIL_SCT)		+= kobil_sct.o
 obj-$(CONFIG_USB_SERIAL_MCT_U232)		+= mct_u232.o
+obj-$(CONFIG_USB_SERIAL_NOKIA_DKU2)		+= nokia_dku2.o
 obj-$(CONFIG_USB_SERIAL_OMNINET)		+= omninet.o
 obj-$(CONFIG_USB_SERIAL_OPTION)			+= option.o
 obj-$(CONFIG_USB_SERIAL_PL2303)			+= pl2303.o
diff --git a/drivers/usb/serial/nokia_dku2.c b/drivers/usb/serial/nokia_dku2.c
new file mode 100644
index 0000000..fad01be
--- /dev/null
+++ b/drivers/usb/serial/nokia_dku2.c
@@ -0,0 +1,142 @@
+/*
+ *  Nokia DKU2 USB driver
+ *
+ *  Copyright (C) 2004
+ *  Author: C Kemp
+ *
+ *  This program is largely derived from work by the linux-usb group
+ *  and associated source files.  Please see the usb/serial files for
+ *  individual credits and copyrights.
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  20.09.2005 - Matthias Blaesing <matthias.blaesing@rwth-aachen.de>
+ *  Added short name to device structure to make driver load into kernel 2.6.13
+ *
+ *  20.09.2005 - Matthias Blaesing <matthias.blaesing@rwth-aachen.de>
+ *  Added usb_deregister to exit code - to allow remove and reinsert of module
+ */
+
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_driver.h>
+#include <linux/tty_flip.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include "usb-serial.h"
+
+
+#define NOKIA_VENDOR_ID		0x0421
+#define NOKIA7600_PRODUCT_ID	0x0400
+#define NOKIA6230_PRODUCT_ID	0x040f
+#define NOKIA6170_PRODUCT_ID	0x0416
+#define NOKIA6670_PRODUCT_ID	0x041d
+#define NOKIA6680_PRODUCT_ID	0x041e
+#define NOKIA6230i_PRODUCT_ID	0x0428
+
+#define NOKIA_AT_PORT	0x82
+#define NOKIA_FBUS_PORT	0x86
+
+/*
+ * Version Information
+ */
+#define DRIVER_VERSION	"v0.2"
+#define DRIVER_AUTHOR	"C Kemp"
+#define DRIVER_DESC	"Nokia DKU2 Driver"
+
+static struct usb_device_id id_table [] = {
+	{ USB_DEVICE(NOKIA_VENDOR_ID, NOKIA7600_PRODUCT_ID) },
+	{ USB_DEVICE(NOKIA_VENDOR_ID, NOKIA6230_PRODUCT_ID) },
+	{ USB_DEVICE(NOKIA_VENDOR_ID, NOKIA6170_PRODUCT_ID) },
+	{ USB_DEVICE(NOKIA_VENDOR_ID, NOKIA6670_PRODUCT_ID) },
+	{ USB_DEVICE(NOKIA_VENDOR_ID, NOKIA6680_PRODUCT_ID) },
+	{ USB_DEVICE(NOKIA_VENDOR_ID, NOKIA6230i_PRODUCT_ID) },
+	{ }			/* Terminating entry */
+};
+MODULE_DEVICE_TABLE(usb, id_table);
+
+/* The only thing which makes this device different from a generic
+ * device is that we have to set an alternative configuration to make
+ * the relevant endpoints available. In 2.6 this is really easy... */
+static int nokia_probe(struct usb_serial *serial,
+		       const struct usb_device_id *id)
+{
+	int retval = -ENODEV;
+
+	if (serial->interface->altsetting[0].endpoint[0].desc.bEndpointAddress == NOKIA_AT_PORT) {
+		/* the AT port */
+		dev_info(&serial->dev->dev, "Nokia AT Port:\n");
+		retval = 0;
+	} else if (serial->interface->num_altsetting == 2 &&
+		   serial->interface->altsetting[1].endpoint[0].desc.bEndpointAddress == NOKIA_FBUS_PORT) {
+		/* the FBUS port */
+		dev_info(&serial->dev->dev, "Nokia FBUS Port:\n");
+		usb_set_interface(serial->dev, 10, 1);
+		retval = 0;
+	}
+
+	return retval;
+}
+
+static struct usb_driver nokia_driver = {
+	.owner =	THIS_MODULE,
+	.name =		"nokia_dku2",
+	.probe =	usb_serial_probe,
+	.disconnect =	usb_serial_disconnect,
+	.id_table =	id_table,
+};
+
+static struct usb_serial_driver nokia_serial_driver = {
+	.driver = {
+		.owner =	THIS_MODULE,
+		.name = 	"nokia_dku2",
+	},
+	.description =		"Nokia 7600/6230(i)/6170/66x0 DKU2 driver",
+	.id_table =		id_table,
+	.num_interrupt_in =	1,
+	.num_bulk_in =		1,
+	.num_bulk_out =		1,
+	.num_ports =		1,
+	.probe =		nokia_probe,
+};
+
+static int __init nokia_init(void)
+{
+        int retval;
+
+	retval = usb_serial_register(&nokia_serial_driver);
+	if (retval)
+		return retval;
+
+	retval = usb_register(&nokia_driver);
+	if (retval) {
+	        usb_serial_deregister(&nokia_serial_driver);
+		return retval;
+	}
+
+	info(DRIVER_VERSION " " DRIVER_AUTHOR);
+	info(DRIVER_DESC);
+
+	return retval;
+}
+
+static void __exit nokia_exit(void)
+{
+	usb_deregister(&nokia_driver);
+	usb_serial_deregister(&nokia_serial_driver);
+}
+
+module_init(nokia_init);
+module_exit(nokia_exit);
+
+MODULE_AUTHOR(DRIVER_AUTHOR);
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
-- 
cgit v1.1


From 4303fc6f055cf1a7ec63c3c3fd777b91b7d576f1 Mon Sep 17 00:00:00 2001
From: Greg Kroah-Hartman <gregkh@suse.de>
Date: Fri, 28 Oct 2005 19:59:31 -0700
Subject: USB: fix up some odd parts due to partial merges

Thanks to Andrew for doing the hard work on this.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
 drivers/usb/core/hub.c      | 2 +-
 drivers/usb/host/ehci-pci.c | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

(limited to 'drivers')

diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 9660a89..256d9f6 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1674,7 +1674,7 @@ int usb_suspend_device(struct usb_device *udev)
 	return 0;
 #endif
 }
-
+EXPORT_SYMBOL_GPL(usb_suspend_device);
 
 /*
  * If the USB "suspend" state is in use (rather than "global suspend"),
diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c
index 7872469..1450088 100644
--- a/drivers/usb/host/ehci-pci.c
+++ b/drivers/usb/host/ehci-pci.c
@@ -252,7 +252,7 @@ static int ehci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
 	(void) usb_suspend_device (hcd->self.root_hub);
 #else
 	usb_lock_device (hcd->self.root_hub);
-	(void) ehci_hub_suspend (hcd);
+	(void) ehci_bus_suspend (hcd);
 	usb_unlock_device (hcd->self.root_hub);
 #endif
 
@@ -285,7 +285,7 @@ static int ehci_pci_resume (struct usb_hcd *hcd)
 			continue;
 		if (status & (PORT_SUSPEND | PORT_OWNER)) {
 			down (&hcd->self.root_hub->serialize);
-			retval = ehci_hub_resume (hcd);
+			retval = ehci_bus_resume (hcd);
 			up (&hcd->self.root_hub->serialize);
 			break;
 		}
-- 
cgit v1.1