From 4516d50aabedbe5ae334155193e4d35c02390d9a Mon Sep 17 00:00:00 2001 From: Peter Hurley Date: Thu, 22 Jan 2015 12:24:30 -0500 Subject: serial: 8250: Use canary to restart console after suspend When using no_console_suspend, the serial console may be powered off anyway during system sleep. Upon resume, the port may be in its default power-on state, but is expected to continue console i/o before the device has received its pm callback. The resultant garbage i/o can cause all kinds of havoc on the remote end. Use the scratch register as a canary to discover if the console has been powered-off. Write a non-zero value to the scratch register at port suspend and reprogram the port before any console i/o if the scratch register != canary before port resume. This workaround is disabled for omap_8250 (which uses different divisor programming). Credit to Doug Anderson for the idea of using the scratch register canary to discover port power-down. Cc: Doug Anderson Signed-off-by: Peter Hurley Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250_core.c | 35 ++++++++++++++++++++++++++++++++++- 1 file changed, 34 insertions(+), 1 deletion(-) (limited to 'drivers/tty') diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index c8ecfaf..1449c56 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -3267,6 +3267,27 @@ serial8250_console_write(struct console *co, const char *s, unsigned int count) else serial_port_out(port, UART_IER, 0); + /* check scratch reg to see if port powered off during system sleep */ + if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) { + struct ktermios termios; + unsigned int baud, quot, frac = 0; + + termios.c_cflag = port->cons->cflag; + if (port->state->port.tty && termios.c_cflag == 0) + termios.c_cflag = port->state->port.tty->termios.c_cflag; + + baud = uart_get_baud_rate(port, &termios, NULL, + port->uartclk / 16 / 0xffff, + port->uartclk / 16); + quot = serial8250_get_divisor(up, baud, &frac); + + serial8250_set_divisor(port, baud, quot, frac); + serial_port_out(port, UART_LCR, up->lcr); + serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS); + + up->canary = 0; + } + uart_console_write(port, s, count, serial8250_console_putchar); /* @@ -3417,7 +3438,17 @@ int __init early_serial_setup(struct uart_port *port) */ void serial8250_suspend_port(int line) { - uart_suspend_port(&serial8250_reg, &serial8250_ports[line].port); + struct uart_8250_port *up = &serial8250_ports[line]; + struct uart_port *port = &up->port; + + if (!console_suspend_enabled && uart_console(port) && + port->type != PORT_8250) { + unsigned char canary = 0xa5; + serial_out(up, UART_SCR, canary); + up->canary = canary; + } + + uart_suspend_port(&serial8250_reg, port); } /** @@ -3431,6 +3462,8 @@ void serial8250_resume_port(int line) struct uart_8250_port *up = &serial8250_ports[line]; struct uart_port *port = &up->port; + up->canary = 0; + if (up->capabilities & UART_NATSEMI) { /* Ensure it's still in high speed mode */ serial_port_out(port, UART_LCR, 0xE0); -- cgit v1.1