From d7584ed2b994a572326650b0c4d2c25961e6f49d Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Tue, 15 Jan 2008 09:56:13 -0600 Subject: [POWERPC] qe-uart: add support for Freescale QUICCEngine UART Add file ucc_uart.c, a serial device driver for the Freescale QUICCEngine. Update the Kconfig and Makefile accordingly. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala --- drivers/serial/ucc_uart.c | 1514 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1514 insertions(+) create mode 100644 drivers/serial/ucc_uart.c (limited to 'drivers/serial/ucc_uart.c') diff --git a/drivers/serial/ucc_uart.c b/drivers/serial/ucc_uart.c new file mode 100644 index 0000000..e0994f0 --- /dev/null +++ b/drivers/serial/ucc_uart.c @@ -0,0 +1,1514 @@ +/* + * Freescale QUICC Engine UART device driver + * + * Author: Timur Tabi + * + * Copyright 2007 Freescale Semiconductor, Inc. This file is licensed under + * the terms of the GNU General Public License version 2. This program + * is licensed "as is" without any warranty of any kind, whether express + * or implied. + * + * This driver adds support for UART devices via Freescale's QUICC Engine + * found on some Freescale SOCs. + * + * If Soft-UART support is needed but not already present, then this driver + * will request and upload the "Soft-UART" microcode upon probe. The + * filename of the microcode should be fsl_qe_ucode_uart_X_YZ.bin, where "X" + * is the name of the SOC (e.g. 8323), and YZ is the revision of the SOC, + * (e.g. "11" for 1.1). + */ + +#include +#include +#include +#include +#include +#include + +#include +#include + +#include +#include + +/* + * The GUMR flag for Soft UART. This would normally be defined in qe.h, + * but Soft-UART is a hack and we want to keep everything related to it in + * this file. + */ +#define UCC_SLOW_GUMR_H_SUART 0x00004000 /* Soft-UART */ + +/* + * soft_uart is 1 if we need to use Soft-UART mode + */ +static int soft_uart; +/* + * firmware_loaded is 1 if the firmware has been loaded, 0 otherwise. + */ +static int firmware_loaded; + +/* Enable this macro to configure all serial ports in internal loopback + mode */ +/* #define LOOPBACK */ + +/* The major and minor device numbers are defined in + * http://www.lanana.org/docs/device-list/devices-2.6+.txt. For the QE + * UART, we have major number 204 and minor numbers 46 - 49, which are the + * same as for the CPM2. This decision was made because no Freescale part + * has both a CPM and a QE. + */ +#define SERIAL_QE_MAJOR 204 +#define SERIAL_QE_MINOR 46 + +/* Since we only have minor numbers 46 - 49, there is a hard limit of 4 ports */ +#define UCC_MAX_UART 4 + +/* The number of buffer descriptors for receiving characters. */ +#define RX_NUM_FIFO 4 + +/* The number of buffer descriptors for transmitting characters. */ +#define TX_NUM_FIFO 4 + +/* The maximum size of the character buffer for a single RX BD. */ +#define RX_BUF_SIZE 32 + +/* The maximum size of the character buffer for a single TX BD. */ +#define TX_BUF_SIZE 32 + +/* + * The number of jiffies to wait after receiving a close command before the + * device is actually closed. This allows the last few characters to be + * sent over the wire. + */ +#define UCC_WAIT_CLOSING 100 + +struct ucc_uart_pram { + struct ucc_slow_pram common; + u8 res1[8]; /* reserved */ + __be16 maxidl; /* Maximum idle chars */ + __be16 idlc; /* temp idle counter */ + __be16 brkcr; /* Break count register */ + __be16 parec; /* receive parity error counter */ + __be16 frmec; /* receive framing error counter */ + __be16 nosec; /* receive noise counter */ + __be16 brkec; /* receive break condition counter */ + __be16 brkln; /* last received break length */ + __be16 uaddr[2]; /* UART address character 1 & 2 */ + __be16 rtemp; /* Temp storage */ + __be16 toseq; /* Transmit out of sequence char */ + __be16 cchars[8]; /* control characters 1-8 */ + __be16 rccm; /* receive control character mask */ + __be16 rccr; /* receive control character register */ + __be16 rlbc; /* receive last break character */ + __be16 res2; /* reserved */ + __be32 res3; /* reserved, should be cleared */ + u8 res4; /* reserved, should be cleared */ + u8 res5[3]; /* reserved, should be cleared */ + __be32 res6; /* reserved, should be cleared */ + __be32 res7; /* reserved, should be cleared */ + __be32 res8; /* reserved, should be cleared */ + __be32 res9; /* reserved, should be cleared */ + __be32 res10; /* reserved, should be cleared */ + __be32 res11; /* reserved, should be cleared */ + __be32 res12; /* reserved, should be cleared */ + __be32 res13; /* reserved, should be cleared */ +/* The rest is for Soft-UART only */ + __be16 supsmr; /* 0x90, Shadow UPSMR */ + __be16 res92; /* 0x92, reserved, initialize to 0 */ + __be32 rx_state; /* 0x94, RX state, initialize to 0 */ + __be32 rx_cnt; /* 0x98, RX count, initialize to 0 */ + u8 rx_length; /* 0x9C, Char length, set to 1+CL+PEN+1+SL */ + u8 rx_bitmark; /* 0x9D, reserved, initialize to 0 */ + u8 rx_temp_dlst_qe; /* 0x9E, reserved, initialize to 0 */ + u8 res14[0xBC - 0x9F]; /* reserved */ + __be32 dump_ptr; /* 0xBC, Dump pointer */ + __be32 rx_frame_rem; /* 0xC0, reserved, initialize to 0 */ + u8 rx_frame_rem_size; /* 0xC4, reserved, initialize to 0 */ + u8 tx_mode; /* 0xC5, mode, 0=AHDLC, 1=UART */ + __be16 tx_state; /* 0xC6, TX state */ + u8 res15[0xD0 - 0xC8]; /* reserved */ + __be32 resD0; /* 0xD0, reserved, initialize to 0 */ + u8 resD4; /* 0xD4, reserved, initialize to 0 */ + __be16 resD5; /* 0xD5, reserved, initialize to 0 */ +} __attribute__ ((packed)); + +/* SUPSMR definitions, for Soft-UART only */ +#define UCC_UART_SUPSMR_SL 0x8000 +#define UCC_UART_SUPSMR_RPM_MASK 0x6000 +#define UCC_UART_SUPSMR_RPM_ODD 0x0000 +#define UCC_UART_SUPSMR_RPM_LOW 0x2000 +#define UCC_UART_SUPSMR_RPM_EVEN 0x4000 +#define UCC_UART_SUPSMR_RPM_HIGH 0x6000 +#define UCC_UART_SUPSMR_PEN 0x1000 +#define UCC_UART_SUPSMR_TPM_MASK 0x0C00 +#define UCC_UART_SUPSMR_TPM_ODD 0x0000 +#define UCC_UART_SUPSMR_TPM_LOW 0x0400 +#define UCC_UART_SUPSMR_TPM_EVEN 0x0800 +#define UCC_UART_SUPSMR_TPM_HIGH 0x0C00 +#define UCC_UART_SUPSMR_FRZ 0x0100 +#define UCC_UART_SUPSMR_UM_MASK 0x00c0 +#define UCC_UART_SUPSMR_UM_NORMAL 0x0000 +#define UCC_UART_SUPSMR_UM_MAN_MULTI 0x0040 +#define UCC_UART_SUPSMR_UM_AUTO_MULTI 0x00c0 +#define UCC_UART_SUPSMR_CL_MASK 0x0030 +#define UCC_UART_SUPSMR_CL_8 0x0030 +#define UCC_UART_SUPSMR_CL_7 0x0020 +#define UCC_UART_SUPSMR_CL_6 0x0010 +#define UCC_UART_SUPSMR_CL_5 0x0000 + +#define UCC_UART_TX_STATE_AHDLC 0x00 +#define UCC_UART_TX_STATE_UART 0x01 +#define UCC_UART_TX_STATE_X1 0x00 +#define UCC_UART_TX_STATE_X16 0x80 + +#define UCC_UART_PRAM_ALIGNMENT 0x100 + +#define UCC_UART_SIZE_OF_BD UCC_SLOW_SIZE_OF_BD +#define NUM_CONTROL_CHARS 8 + +/* Private per-port data structure */ +struct uart_qe_port { + struct uart_port port; + struct ucc_slow __iomem *uccp; + struct ucc_uart_pram __iomem *uccup; + struct ucc_slow_info us_info; + struct ucc_slow_private *us_private; + struct device_node *np; + unsigned int ucc_num; /* First ucc is 0, not 1 */ + + u16 rx_nrfifos; + u16 rx_fifosize; + u16 tx_nrfifos; + u16 tx_fifosize; + int wait_closing; + u32 flags; + struct qe_bd *rx_bd_base; + struct qe_bd *rx_cur; + struct qe_bd *tx_bd_base; + struct qe_bd *tx_cur; + unsigned char *tx_buf; + unsigned char *rx_buf; + void *bd_virt; /* virtual address of the BD buffers */ + dma_addr_t bd_dma_addr; /* bus address of the BD buffers */ + unsigned int bd_size; /* size of BD buffer space */ +}; + +static struct uart_driver ucc_uart_driver = { + .owner = THIS_MODULE, + .driver_name = "serial", + .dev_name = "ttyQE", + .major = SERIAL_QE_MAJOR, + .minor = SERIAL_QE_MINOR, + .nr = UCC_MAX_UART, +}; + +/* + * Virtual to physical address translation. + * + * Given the virtual address for a character buffer, this function returns + * the physical (DMA) equivalent. + */ +static inline dma_addr_t cpu2qe_addr(void *addr, struct uart_qe_port *qe_port) +{ + if (likely((addr >= qe_port->bd_virt)) && + (addr < (qe_port->bd_virt + qe_port->bd_size))) + return qe_port->bd_dma_addr + (addr - qe_port->bd_virt); + + /* something nasty happened */ + printk(KERN_ERR "%s: addr=%p\n", __FUNCTION__, addr); + BUG(); + return 0; +} + +/* + * Physical to virtual address translation. + * + * Given the physical (DMA) address for a character buffer, this function + * returns the virtual equivalent. + */ +static inline void *qe2cpu_addr(dma_addr_t addr, struct uart_qe_port *qe_port) +{ + /* sanity check */ + if (likely((addr >= qe_port->bd_dma_addr) && + (addr < (qe_port->bd_dma_addr + qe_port->bd_size)))) + return qe_port->bd_virt + (addr - qe_port->bd_dma_addr); + + /* something nasty happened */ + printk(KERN_ERR "%s: addr=%x\n", __FUNCTION__, addr); + BUG(); + return NULL; +} + +/* + * Return 1 if the QE is done transmitting all buffers for this port + * + * This function scans each BD in sequence. If we find a BD that is not + * ready (READY=1), then we return 0 indicating that the QE is still sending + * data. If we reach the last BD (WRAP=1), then we know we've scanned + * the entire list, and all BDs are done. + */ +static unsigned int qe_uart_tx_empty(struct uart_port *port) +{ + struct uart_qe_port *qe_port = + container_of(port, struct uart_qe_port, port); + struct qe_bd *bdp = qe_port->tx_bd_base; + + while (1) { + if (in_be16(&bdp->status) & BD_SC_READY) + /* This BD is not done, so return "not done" */ + return 0; + + if (in_be16(&bdp->status) & BD_SC_WRAP) + /* + * This BD is done and it's the last one, so return + * "done" + */ + return 1; + + bdp++; + }; +} + +/* + * Set the modem control lines + * + * Although the QE can control the modem control lines (e.g. CTS), we + * don't need that support. This function must exist, however, otherwise + * the kernel will panic. + */ +void qe_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ +} + +/* + * Get the current modem control line status + * + * Although the QE can control the modem control lines (e.g. CTS), this + * driver currently doesn't support that, so we always return Carrier + * Detect, Data Set Ready, and Clear To Send. + */ +static unsigned int qe_uart_get_mctrl(struct uart_port *port) +{ + return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS; +} + +/* + * Disable the transmit interrupt. + * + * Although this function is called "stop_tx", it does not actually stop + * transmission of data. Instead, it tells the QE to not generate an + * interrupt when the UCC is finished sending characters. + */ +static void qe_uart_stop_tx(struct uart_port *port) +{ + struct uart_qe_port *qe_port = + container_of(port, struct uart_qe_port, port); + + clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX); +} + +/* + * Transmit as many characters to the HW as possible. + * + * This function will attempt to stuff of all the characters from the + * kernel's transmit buffer into TX BDs. + * + * A return value of non-zero indicates that it sucessfully stuffed all + * characters from the kernel buffer. + * + * A return value of zero indicates that there are still characters in the + * kernel's buffer that have not been transmitted, but there are no more BDs + * available. This function should be called again after a BD has been made + * available. + */ +static int qe_uart_tx_pump(struct uart_qe_port *qe_port) +{ + struct qe_bd *bdp; + unsigned char *p; + unsigned int count; + struct uart_port *port = &qe_port->port; + struct circ_buf *xmit = &port->info->xmit; + + bdp = qe_port->rx_cur; + + /* Handle xon/xoff */ + if (port->x_char) { + /* Pick next descriptor and fill from buffer */ + bdp = qe_port->tx_cur; + + p = qe2cpu_addr(bdp->buf, qe_port); + + *p++ = port->x_char; + out_be16(&bdp->length, 1); + setbits16(&bdp->status, BD_SC_READY); + /* Get next BD. */ + if (in_be16(&bdp->status) & BD_SC_WRAP) + bdp = qe_port->tx_bd_base; + else + bdp++; + qe_port->tx_cur = bdp; + + port->icount.tx++; + port->x_char = 0; + return 1; + } + + if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { + qe_uart_stop_tx(port); + return 0; + } + + /* Pick next descriptor and fill from buffer */ + bdp = qe_port->tx_cur; + + while (!(in_be16(&bdp->status) & BD_SC_READY) && + (xmit->tail != xmit->head)) { + count = 0; + p = qe2cpu_addr(bdp->buf, qe_port); + while (count < qe_port->tx_fifosize) { + *p++ = xmit->buf[xmit->tail]; + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + port->icount.tx++; + count++; + if (xmit->head == xmit->tail) + break; + } + + out_be16(&bdp->length, count); + setbits16(&bdp->status, BD_SC_READY); + + /* Get next BD. */ + if (in_be16(&bdp->status) & BD_SC_WRAP) + bdp = qe_port->tx_bd_base; + else + bdp++; + } + qe_port->tx_cur = bdp; + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + if (uart_circ_empty(xmit)) { + /* The kernel buffer is empty, so turn off TX interrupts. We + don't need to be told when the QE is finished transmitting + the data. */ + qe_uart_stop_tx(port); + return 0; + } + + return 1; +} + +/* + * Start transmitting data + * + * This function will start transmitting any available data, if the port + * isn't already transmitting data. + */ +static void qe_uart_start_tx(struct uart_port *port) +{ + struct uart_qe_port *qe_port = + container_of(port, struct uart_qe_port, port); + + /* If we currently are transmitting, then just return */ + if (in_be16(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX) + return; + + /* Otherwise, pump the port and start transmission */ + if (qe_uart_tx_pump(qe_port)) + setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX); +} + +/* + * Stop transmitting data + */ +static void qe_uart_stop_rx(struct uart_port *port) +{ + struct uart_qe_port *qe_port = + container_of(port, struct uart_qe_port, port); + + clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX); +} + +/* + * Enable status change interrupts + * + * We don't support status change interrupts, but we need to define this + * function otherwise the kernel will panic. + */ +static void qe_uart_enable_ms(struct uart_port *port) +{ +} + +/* Start or stop sending break signal + * + * This function controls the sending of a break signal. If break_state=1, + * then we start sending a break signal. If break_state=0, then we stop + * sending the break signal. + */ +static void qe_uart_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_qe_port *qe_port = + container_of(port, struct uart_qe_port, port); + + if (break_state) + ucc_slow_stop_tx(qe_port->us_private); + else + ucc_slow_restart_tx(qe_port->us_private); +} + +/* ISR helper function for receiving character. + * + * This function is called by the ISR to handling receiving characters + */ +static void qe_uart_int_rx(struct uart_qe_port *qe_port) +{ + int i; + unsigned char ch, *cp; + struct uart_port *port = &qe_port->port; + struct tty_struct *tty = port->info->tty; + struct qe_bd *bdp; + u16 status; + unsigned int flg; + + /* Just loop through the closed BDs and copy the characters into + * the buffer. + */ + bdp = qe_port->rx_cur; + while (1) { + status = in_be16(&bdp->status); + + /* If this one is empty, then we assume we've read them all */ + if (status & BD_SC_EMPTY) + break; + + /* get number of characters, and check space in RX buffer */ + i = in_be16(&bdp->length); + + /* If we don't have enough room in RX buffer for the entire BD, + * then we try later, which will be the next RX interrupt. + */ + if (tty_buffer_request_room(tty, i) < i) { + dev_dbg(port->dev, "ucc-uart: no room in RX buffer\n"); + return; + } + + /* get pointer */ + cp = qe2cpu_addr(bdp->buf, qe_port); + + /* loop through the buffer */ + while (i-- > 0) { + ch = *cp++; + port->icount.rx++; + flg = TTY_NORMAL; + + if (!i && status & + (BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV)) + goto handle_error; + if (uart_handle_sysrq_char(port, ch)) + continue; + +error_return: + tty_insert_flip_char(tty, ch, flg); + + } + + /* This BD is ready to be used again. Clear status. get next */ + clrsetbits_be16(&bdp->status, BD_SC_BR | BD_SC_FR | BD_SC_PR | + BD_SC_OV | BD_SC_ID, BD_SC_EMPTY); + if (in_be16(&bdp->status) & BD_SC_WRAP) + bdp = qe_port->rx_bd_base; + else + bdp++; + + } + + /* Write back buffer pointer */ + qe_port->rx_cur = bdp; + + /* Activate BH processing */ + tty_flip_buffer_push(tty); + + return; + + /* Error processing */ + +handle_error: + /* Statistics */ + if (status & BD_SC_BR) + port->icount.brk++; + if (status & BD_SC_PR) + port->icount.parity++; + if (status & BD_SC_FR) + port->icount.frame++; + if (status & BD_SC_OV) + port->icount.overrun++; + + /* Mask out ignored conditions */ + status &= port->read_status_mask; + + /* Handle the remaining ones */ + if (status & BD_SC_BR) + flg = TTY_BREAK; + else if (status & BD_SC_PR) + flg = TTY_PARITY; + else if (status & BD_SC_FR) + flg = TTY_FRAME; + + /* Overrun does not affect the current character ! */ + if (status & BD_SC_OV) + tty_insert_flip_char(tty, 0, TTY_OVERRUN); +#ifdef SUPPORT_SYSRQ + port->sysrq = 0; +#endif + goto error_return; +} + +/* Interrupt handler + * + * This interrupt handler is called after a BD is processed. + */ +static irqreturn_t qe_uart_int(int irq, void *data) +{ + struct uart_qe_port *qe_port = (struct uart_qe_port *) data; + struct ucc_slow __iomem *uccp = qe_port->uccp; + u16 events; + + /* Clear the interrupts */ + events = in_be16(&uccp->ucce); + out_be16(&uccp->ucce, events); + + if (events & UCC_UART_UCCE_BRKE) + uart_handle_break(&qe_port->port); + + if (events & UCC_UART_UCCE_RX) + qe_uart_int_rx(qe_port); + + if (events & UCC_UART_UCCE_TX) + qe_uart_tx_pump(qe_port); + + return events ? IRQ_HANDLED : IRQ_NONE; +} + +/* Initialize buffer descriptors + * + * This function initializes all of the RX and TX buffer descriptors. + */ +static void qe_uart_initbd(struct uart_qe_port *qe_port) +{ + int i; + void *bd_virt; + struct qe_bd *bdp; + + /* Set the physical address of the host memory buffers in the buffer + * descriptors, and the virtual address for us to work with. + */ + bd_virt = qe_port->bd_virt; + bdp = qe_port->rx_bd_base; + qe_port->rx_cur = qe_port->rx_bd_base; + for (i = 0; i < (qe_port->rx_nrfifos - 1); i++) { + out_be16(&bdp->status, BD_SC_EMPTY | BD_SC_INTRPT); + out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); + out_be16(&bdp->length, 0); + bd_virt += qe_port->rx_fifosize; + bdp++; + } + + /* */ + out_be16(&bdp->status, BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT); + out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); + out_be16(&bdp->length, 0); + + /* Set the physical address of the host memory + * buffers in the buffer descriptors, and the + * virtual address for us to work with. + */ + bd_virt = qe_port->bd_virt + + L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize); + qe_port->tx_cur = qe_port->tx_bd_base; + bdp = qe_port->tx_bd_base; + for (i = 0; i < (qe_port->tx_nrfifos - 1); i++) { + out_be16(&bdp->status, BD_SC_INTRPT); + out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); + out_be16(&bdp->length, 0); + bd_virt += qe_port->tx_fifosize; + bdp++; + } + + /* Loopback requires the preamble bit to be set on the first TX BD */ +#ifdef LOOPBACK + setbits16(&qe_port->tx_cur->status, BD_SC_P); +#endif + + out_be16(&bdp->status, BD_SC_WRAP | BD_SC_INTRPT); + out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port)); + out_be16(&bdp->length, 0); +} + +/* + * Initialize a UCC for UART. + * + * This function configures a given UCC to be used as a UART device. Basic + * UCC initialization is handled in qe_uart_request_port(). This function + * does all the UART-specific stuff. + */ +static void qe_uart_init_ucc(struct uart_qe_port *qe_port) +{ + u32 cecr_subblock; + struct ucc_slow __iomem *uccp = qe_port->uccp; + struct ucc_uart_pram *uccup = qe_port->uccup; + + unsigned int i; + + /* First, disable TX and RX in the UCC */ + ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX); + + /* Program the UCC UART parameter RAM */ + out_8(&uccup->common.rbmr, UCC_BMR_GBL | UCC_BMR_BO_BE); + out_8(&uccup->common.tbmr, UCC_BMR_GBL | UCC_BMR_BO_BE); + out_be16(&uccup->common.mrblr, qe_port->rx_fifosize); + out_be16(&uccup->maxidl, 0x10); + out_be16(&uccup->brkcr, 1); + out_be16(&uccup->parec, 0); + out_be16(&uccup->frmec, 0); + out_be16(&uccup->nosec, 0); + out_be16(&uccup->brkec, 0); + out_be16(&uccup->uaddr[0], 0); + out_be16(&uccup->uaddr[1], 0); + out_be16(&uccup->toseq, 0); + for (i = 0; i < 8; i++) + out_be16(&uccup->cchars[i], 0xC000); + out_be16(&uccup->rccm, 0xc0ff); + + /* Configure the GUMR registers for UART */ + if (soft_uart) + /* Soft-UART requires a 1X multiplier for TX */ + clrsetbits_be32(&uccp->gumr_l, + UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | + UCC_SLOW_GUMR_L_RDCR_MASK, + UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 | + UCC_SLOW_GUMR_L_RDCR_16); + else + clrsetbits_be32(&uccp->gumr_l, + UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | + UCC_SLOW_GUMR_L_RDCR_MASK, + UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 | + UCC_SLOW_GUMR_L_RDCR_16); + + clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW, + UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX); + +#ifdef LOOPBACK + clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK, + UCC_SLOW_GUMR_L_DIAG_LOOP); + clrsetbits_be32(&uccp->gumr_h, + UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_RSYN, + UCC_SLOW_GUMR_H_CDS); +#endif + + /* Enable rx interrupts and clear all pending events. */ + out_be16(&uccp->uccm, 0); + out_be16(&uccp->ucce, 0xffff); + out_be16(&uccp->udsr, 0x7e7e); + + /* Initialize UPSMR */ + out_be16(&uccp->upsmr, 0); + + if (soft_uart) { + out_be16(&uccup->supsmr, 0x30); + out_be16(&uccup->res92, 0); + out_be32(&uccup->rx_state, 0); + out_be32(&uccup->rx_cnt, 0); + out_8(&uccup->rx_bitmark, 0); + out_8(&uccup->rx_length, 10); + out_be32(&uccup->dump_ptr, 0x4000); + out_8(&uccup->rx_temp_dlst_qe, 0); + out_be32(&uccup->rx_frame_rem, 0); + out_8(&uccup->rx_frame_rem_size, 0); + /* Soft-UART requires TX to be 1X */ + out_8(&uccup->tx_mode, + UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1); + out_be16(&uccup->tx_state, 0); + out_8(&uccup->resD4, 0); + out_be16(&uccup->resD5, 0); + + /* Set UART mode. + * Enable receive and transmit. + */ + + /* From the microcode errata: + * 1.GUMR_L register, set mode=0010 (QMC). + * 2.Set GUMR_H[17] bit. (UART/AHDLC mode). + * 3.Set GUMR_H[19:20] (Transparent mode) + * 4.Clear GUMR_H[26] (RFW) + * ... + * 6.Receiver must use 16x over sampling + */ + clrsetbits_be32(&uccp->gumr_l, + UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | + UCC_SLOW_GUMR_L_RDCR_MASK, + UCC_SLOW_GUMR_L_MODE_QMC | UCC_SLOW_GUMR_L_TDCR_16 | + UCC_SLOW_GUMR_L_RDCR_16); + + clrsetbits_be32(&uccp->gumr_h, + UCC_SLOW_GUMR_H_RFW | UCC_SLOW_GUMR_H_RSYN, + UCC_SLOW_GUMR_H_SUART | UCC_SLOW_GUMR_H_TRX | + UCC_SLOW_GUMR_H_TTX | UCC_SLOW_GUMR_H_TFL); + +#ifdef LOOPBACK + clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK, + UCC_SLOW_GUMR_L_DIAG_LOOP); + clrbits32(&uccp->gumr_h, UCC_SLOW_GUMR_H_CTSP | + UCC_SLOW_GUMR_H_CDS); +#endif + + cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num); + qe_issue_cmd(QE_INIT_TX_RX, cecr_subblock, + QE_CR_PROTOCOL_UNSPECIFIED, 0); + } +} + +/* + * Initialize the port. + */ +static int qe_uart_startup(struct uart_port *port) +{ + struct uart_qe_port *qe_port = + container_of(port, struct uart_qe_port, port); + int ret; + + /* + * If we're using Soft-UART mode, then we need to make sure the + * firmware has been uploaded first. + */ + if (soft_uart && !firmware_loaded) { + dev_err(port->dev, "Soft-UART firmware not uploaded\n"); + return -ENODEV; + } + + qe_uart_initbd(qe_port); + qe_uart_init_ucc(qe_port); + + /* Install interrupt handler. */ + ret = request_irq(port->irq, qe_uart_int, IRQF_SHARED, "ucc-uart", + qe_port); + if (ret) { + dev_err(port->dev, "could not claim IRQ %u\n", port->irq); + return ret; + } + + /* Startup rx-int */ + setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX); + ucc_slow_enable(qe_port->us_private, COMM_DIR_RX_AND_TX); + + return 0; +} + +/* + * Shutdown the port. + */ +static void qe_uart_shutdown(struct uart_port *port) +{ + struct uart_qe_port *qe_port = + container_of(port, struct uart_qe_port, port); + struct ucc_slow __iomem *uccp = qe_port->uccp; + unsigned int timeout = 20; + + /* Disable RX and TX */ + + /* Wait for all the BDs marked sent */ + while (!qe_uart_tx_empty(port)) { + if (!--timeout) { + dev_warn(port->dev, "shutdown timeout\n"); + break; + } + set_current_state(TASK_UNINTERRUPTIBLE); + schedule_timeout(2); + } + + if (qe_port->wait_closing) { + /* Wait a bit longer */ + set_current_state(TASK_UNINTERRUPTIBLE); + schedule_timeout(qe_port->wait_closing); + } + + /* Stop uarts */ + ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX); + clrbits16(&uccp->uccm, UCC_UART_UCCE_TX | UCC_UART_UCCE_RX); + + /* Shut them really down and reinit buffer descriptors */ + ucc_slow_graceful_stop_tx(qe_port->us_private); + qe_uart_initbd(qe_port); + + free_irq(port->irq, qe_port); +} + +/* + * Set the serial port parameters. + */ +static void qe_uart_set_termios(struct uart_port *port, + struct ktermios *termios, struct ktermios *old) +{ + struct uart_qe_port *qe_port = + container_of(port, struct uart_qe_port, port); + struct ucc_slow __iomem *uccp = qe_port->uccp; + unsigned int baud; + unsigned long flags; + u16 upsmr = in_be16(&uccp->upsmr); + struct ucc_uart_pram __iomem *uccup = qe_port->uccup; + u16 supsmr = in_be16(&uccup->supsmr); + u8 char_length = 2; /* 1 + CL + PEN + 1 + SL */ + + /* Character length programmed into the mode register is the + * sum of: 1 start bit, number of data bits, 0 or 1 parity bit, + * 1 or 2 stop bits, minus 1. + * The value 'bits' counts this for us. + */ + + /* byte size */ + upsmr &= UCC_UART_UPSMR_CL_MASK; + supsmr &= UCC_UART_SUPSMR_CL_MASK; + + switch (termios->c_cflag & CSIZE) { + case CS5: + upsmr |= UCC_UART_UPSMR_CL_5; + supsmr |= UCC_UART_SUPSMR_CL_5; + char_length += 5; + break; + case CS6: + upsmr |= UCC_UART_UPSMR_CL_6; + supsmr |= UCC_UART_SUPSMR_CL_6; + char_length += 6; + break; + case CS7: + upsmr |= UCC_UART_UPSMR_CL_7; + supsmr |= UCC_UART_SUPSMR_CL_7; + char_length += 7; + break; + default: /* case CS8 */ + upsmr |= UCC_UART_UPSMR_CL_8; + supsmr |= UCC_UART_SUPSMR_CL_8; + char_length += 8; + break; + } + + /* If CSTOPB is set, we want two stop bits */ + if (termios->c_cflag & CSTOPB) { + upsmr |= UCC_UART_UPSMR_SL; + supsmr |= UCC_UART_SUPSMR_SL; + char_length++; /* + SL */ + } + + if (termios->c_cflag & PARENB) { + upsmr |= UCC_UART_UPSMR_PEN; + supsmr |= UCC_UART_SUPSMR_PEN; + char_length++; /* + PEN */ + + if (!(termios->c_cflag & PARODD)) { + upsmr &= ~(UCC_UART_UPSMR_RPM_MASK | + UCC_UART_UPSMR_TPM_MASK); + upsmr |= UCC_UART_UPSMR_RPM_EVEN | + UCC_UART_UPSMR_TPM_EVEN; + supsmr &= ~(UCC_UART_SUPSMR_RPM_MASK | + UCC_UART_SUPSMR_TPM_MASK); + supsmr |= UCC_UART_SUPSMR_RPM_EVEN | + UCC_UART_SUPSMR_TPM_EVEN; + } + } + + /* + * Set up parity check flag + */ + port->read_status_mask = BD_SC_EMPTY | BD_SC_OV; + if (termios->c_iflag & INPCK) + port->read_status_mask |= BD_SC_FR | BD_SC_PR; + if (termios->c_iflag & (BRKINT | PARMRK)) + port->read_status_mask |= BD_SC_BR; + + /* + * Characters to ignore + */ + port->ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= BD_SC_PR | BD_SC_FR; + if (termios->c_iflag & IGNBRK) { + port->ignore_status_mask |= BD_SC_BR; + /* + * If we're ignore parity and break indicators, ignore + * overruns too. (For real raw support). + */ + if (termios->c_iflag & IGNPAR) + port->ignore_status_mask |= BD_SC_OV; + } + /* + * !!! ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + port->read_status_mask &= ~BD_SC_EMPTY; + + baud = uart_get_baud_rate(port, termios, old, 0, 115200); + + /* Do we really need a spinlock here? */ + spin_lock_irqsave(&port->lock, flags); + + out_be16(&uccp->upsmr, upsmr); + if (soft_uart) { + out_be16(&uccup->supsmr, supsmr); + out_8(&uccup->rx_length, char_length); + + /* Soft-UART requires a 1X multiplier for TX */ + qe_setbrg(qe_port->us_info.rx_clock, baud, 16); + qe_setbrg(qe_port->us_info.tx_clock, baud, 1); + } else { + qe_setbrg(qe_port->us_info.rx_clock, baud, 16); + qe_setbrg(qe_port->us_info.tx_clock, baud, 16); + } + + spin_unlock_irqrestore(&port->lock, flags); +} + +/* + * Return a pointer to a string that describes what kind of port this is. + */ +static const char *qe_uart_type(struct uart_port *port) +{ + return "QE"; +} + +/* + * Allocate any memory and I/O resources required by the port. + */ +static int qe_uart_request_port(struct uart_port *port) +{ + int ret; + struct uart_qe_port *qe_port = + container_of(port, struct uart_qe_port, port); + struct ucc_slow_info *us_info = &qe_port->us_info; + struct ucc_slow_private *uccs; + unsigned int rx_size, tx_size; + void *bd_virt; + dma_addr_t bd_dma_addr = 0; + + ret = ucc_slow_init(us_info, &uccs); + if (ret) { + dev_err(port->dev, "could not initialize UCC%u\n", + qe_port->ucc_num); + return ret; + } + + qe_port->us_private = uccs; + qe_port->uccp = uccs->us_regs; + qe_port->uccup = (struct ucc_uart_pram *) uccs->us_pram; + qe_port->rx_bd_base = uccs->rx_bd; + qe_port->tx_bd_base = uccs->tx_bd; + + /* + * Allocate the transmit and receive data buffers. + */ + + rx_size = L1_CACHE_ALIGN(qe_port->rx_nrfifos * qe_port->rx_fifosize); + tx_size = L1_CACHE_ALIGN(qe_port->tx_nrfifos * qe_port->tx_fifosize); + + bd_virt = dma_alloc_coherent(NULL, rx_size + tx_size, &bd_dma_addr, + GFP_KERNEL); + if (!bd_virt) { + dev_err(port->dev, "could not allocate buffer descriptors\n"); + return -ENOMEM; + } + + qe_port->bd_virt = bd_virt; + qe_port->bd_dma_addr = bd_dma_addr; + qe_port->bd_size = rx_size + tx_size; + + qe_port->rx_buf = bd_virt; + qe_port->tx_buf = qe_port->rx_buf + rx_size; + + return 0; +} + +/* + * Configure the port. + * + * We say we're a CPM-type port because that's mostly true. Once the device + * is configured, this driver operates almost identically to the CPM serial + * driver. + */ +static void qe_uart_config_port(struct uart_port *port, int flags) +{ + if (flags & UART_CONFIG_TYPE) { + port->type = PORT_CPM; + qe_uart_request_port(port); + } +} + +/* + * Release any memory and I/O resources that were allocated in + * qe_uart_request_port(). + */ +static void qe_uart_release_port(struct uart_port *port) +{ + struct uart_qe_port *qe_port = + container_of(port, struct uart_qe_port, port); + struct ucc_slow_private *uccs = qe_port->us_private; + + dma_free_coherent(NULL, qe_port->bd_size, qe_port->bd_virt, + qe_port->bd_dma_addr); + + ucc_slow_free(uccs); +} + +/* + * Verify that the data in serial_struct is suitable for this device. + */ +static int qe_uart_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + if (ser->type != PORT_UNKNOWN && ser->type != PORT_CPM) + return -EINVAL; + + if (ser->irq < 0 || ser->irq >= NR_IRQS) + return -EINVAL; + + if (ser->baud_base < 9600) + return -EINVAL; + + return 0; +} +/* UART operations + * + * Details on these functions can be found in Documentation/serial/driver + */ +static struct uart_ops qe_uart_pops = { + .tx_empty = qe_uart_tx_empty, + .set_mctrl = qe_uart_set_mctrl, + .get_mctrl = qe_uart_get_mctrl, + .stop_tx = qe_uart_stop_tx, + .start_tx = qe_uart_start_tx, + .stop_rx = qe_uart_stop_rx, + .enable_ms = qe_uart_enable_ms, + .break_ctl = qe_uart_break_ctl, + .startup = qe_uart_startup, + .shutdown = qe_uart_shutdown, + .set_termios = qe_uart_set_termios, + .type = qe_uart_type, + .release_port = qe_uart_release_port, + .request_port = qe_uart_request_port, + .config_port = qe_uart_config_port, + .verify_port = qe_uart_verify_port, +}; + +/* + * Obtain the SOC model number and revision level + * + * This function parses the device tree to obtain the SOC model. It then + * reads the SVR register to the revision. + * + * The device tree stores the SOC model two different ways. + * + * The new way is: + * + * cpu@0 { + * compatible = "PowerPC,8323"; + * device_type = "cpu"; + * ... + * + * + * The old way is: + * PowerPC,8323@0 { + * device_type = "cpu"; + * ... + * + * This code first checks the new way, and then the old way. + */ +static unsigned int soc_info(unsigned int *rev_h, unsigned int *rev_l) +{ + struct device_node *np; + const char *soc_string; + unsigned int svr; + unsigned int soc; + + /* Find the CPU node */ + np = of_find_node_by_type(NULL, "cpu"); + if (!np) + return 0; + /* Find the compatible property */ + soc_string = of_get_property(np, "compatible", NULL); + if (!soc_string) + /* No compatible property, so try the name. */ + soc_string = np->name; + + /* Extract the SOC number from the "PowerPC," string */ + if ((sscanf(soc_string, "PowerPC,%u", &soc) != 1) || !soc) + return 0; + + /* Get the revision from the SVR */ + svr = mfspr(SPRN_SVR); + *rev_h = (svr >> 4) & 0xf; + *rev_l = svr & 0xf; + + return soc; +} + +/* + * requst_firmware_nowait() callback function + * + * This function is called by the kernel when a firmware is made available, + * or if it times out waiting for the firmware. + */ +static void uart_firmware_cont(const struct firmware *fw, void *context) +{ + struct qe_firmware *firmware; + struct device *dev = context; + int ret; + + if (!fw) { + dev_err(dev, "firmware not found\n"); + return; + } + + firmware = (struct qe_firmware *) fw->data; + + if (firmware->header.length != fw->size) { + dev_err(dev, "invalid firmware\n"); + return; + } + + ret = qe_upload_firmware(firmware); + if (ret) { + dev_err(dev, "could not load firmware\n"); + return; + } + + firmware_loaded = 1; +} + +static int ucc_uart_probe(struct of_device *ofdev, + const struct of_device_id *match) +{ + struct device_node *np = ofdev->node; + const unsigned int *iprop; /* Integer OF properties */ + const char *sprop; /* String OF properties */ + struct uart_qe_port *qe_port = NULL; + struct resource res; + int ret; + + /* + * Determine if we need Soft-UART mode + */ + if (of_find_property(np, "soft-uart", NULL)) { + dev_dbg(&ofdev->dev, "using Soft-UART mode\n"); + soft_uart = 1; + } + + /* + * If we are using Soft-UART, determine if we need to upload the + * firmware, too. + */ + if (soft_uart) { + struct qe_firmware_info *qe_fw_info; + + qe_fw_info = qe_get_firmware_info(); + + /* Check if the firmware has been uploaded. */ + if (qe_fw_info && strstr(qe_fw_info->id, "Soft-UART")) { + firmware_loaded = 1; + } else { + char filename[32]; + unsigned int soc; + unsigned int rev_h; + unsigned int rev_l; + + soc = soc_info(&rev_h, &rev_l); + if (!soc) { + dev_err(&ofdev->dev, "unknown CPU model\n"); + return -ENXIO; + } + sprintf(filename, "fsl_qe_ucode_uart_%u_%u%u.bin", + soc, rev_h, rev_l); + + dev_info(&ofdev->dev, "waiting for firmware %s\n", + filename); + + /* + * We call request_firmware_nowait instead of + * request_firmware so that the driver can load and + * initialize the ports without holding up the rest of + * the kernel. If hotplug support is enabled in the + * kernel, then we use it. + */ + ret = request_firmware_nowait(THIS_MODULE, + FW_ACTION_HOTPLUG, filename, &ofdev->dev, + &ofdev->dev, uart_firmware_cont); + if (ret) { + dev_err(&ofdev->dev, + "could not load firmware %s\n", + filename); + return ret; + } + } + } + + qe_port = kzalloc(sizeof(struct uart_qe_port), GFP_KERNEL); + if (!qe_port) { + dev_err(&ofdev->dev, "can't allocate QE port structure\n"); + return -ENOMEM; + } + + /* Search for IRQ and mapbase */ + ret = of_address_to_resource(np, 0, &res); + if (ret) { + dev_err(&ofdev->dev, "missing 'reg' property in device tree\n"); + kfree(qe_port); + return ret; + } + if (!res.start) { + dev_err(&ofdev->dev, "invalid 'reg' property in device tree\n"); + kfree(qe_port); + return -EINVAL; + } + qe_port->port.mapbase = res.start; + + /* Get the UCC number (device ID) */ + /* UCCs are numbered 1-7 */ + iprop = of_get_property(np, "device-id", NULL); + if (!iprop || (*iprop < 1) || (*iprop > UCC_MAX_NUM)) { + dev_err(&ofdev->dev, + "missing or invalid UCC specified in device tree\n"); + kfree(qe_port); + return -ENODEV; + } + qe_port->ucc_num = *iprop - 1; + + /* + * In the future, we should not require the BRG to be specified in the + * device tree. If no clock-source is specified, then just pick a BRG + * to use. This requires a new QE library function that manages BRG + * assignments. + */ + + sprop = of_get_property(np, "rx-clock-name", NULL); + if (!sprop) { + dev_err(&ofdev->dev, "missing rx-clock-name in device tree\n"); + kfree(qe_port); + return -ENODEV; + } + + qe_port->us_info.rx_clock = qe_clock_source(sprop); + if ((qe_port->us_info.rx_clock < QE_BRG1) || + (qe_port->us_info.rx_clock > QE_BRG16)) { + dev_err(&ofdev->dev, "rx-clock-name must be a BRG for UART\n"); + kfree(qe_port); + return -ENODEV; + } + +#ifdef LOOPBACK + /* In internal loopback mode, TX and RX must use the same clock */ + qe_port->us_info.tx_clock = qe_port->us_info.rx_clock; +#else + sprop = of_get_property(np, "tx-clock-name", NULL); + if (!sprop) { + dev_err(&ofdev->dev, "missing tx-clock-name in device tree\n"); + kfree(qe_port); + return -ENODEV; + } + qe_port->us_info.tx_clock = qe_clock_source(sprop); +#endif + if ((qe_port->us_info.tx_clock < QE_BRG1) || + (qe_port->us_info.tx_clock > QE_BRG16)) { + dev_err(&ofdev->dev, "tx-clock-name must be a BRG for UART\n"); + kfree(qe_port); + return -ENODEV; + } + + /* Get the port number, numbered 0-3 */ + iprop = of_get_property(np, "port-number", NULL); + if (!iprop) { + dev_err(&ofdev->dev, "missing port-number in device tree\n"); + kfree(qe_port); + return -EINVAL; + } + qe_port->port.line = *iprop; + if (qe_port->port.line >= UCC_MAX_UART) { + dev_err(&ofdev->dev, "port-number must be 0-%u\n", + UCC_MAX_UART - 1); + kfree(qe_port); + return -EINVAL; + } + + qe_port->port.irq = irq_of_parse_and_map(np, 0); + if (qe_port->port.irq == NO_IRQ) { + dev_err(&ofdev->dev, "could not map IRQ for UCC%u\n", + qe_port->ucc_num + 1); + kfree(qe_port); + return -EINVAL; + } + + /* + * Newer device trees have an "fsl,qe" compatible property for the QE + * node, but we still need to support older device trees. + */ + np = of_find_compatible_node(NULL, NULL, "fsl,qe"); + if (!np) { + np = of_find_node_by_type(NULL, "qe"); + if (!np) { + dev_err(&ofdev->dev, "could not find 'qe' node\n"); + kfree(qe_port); + return -EINVAL; + } + } + + iprop = of_get_property(np, "brg-frequency", NULL); + if (!iprop) { + dev_err(&ofdev->dev, + "missing brg-frequency in device tree\n"); + kfree(qe_port); + return -EINVAL; + } + + if (*iprop) + qe_port->port.uartclk = *iprop; + else { + /* + * Older versions of U-Boot do not initialize the brg-frequency + * property, so in this case we assume the BRG frequency is + * half the QE bus frequency. + */ + iprop = of_get_property(np, "bus-frequency", NULL); + if (!iprop) { + dev_err(&ofdev->dev, + "missing QE bus-frequency in device tree\n"); + kfree(qe_port); + return -EINVAL; + } + if (*iprop) + qe_port->port.uartclk = *iprop / 2; + else { + dev_err(&ofdev->dev, + "invalid QE bus-frequency in device tree\n"); + kfree(qe_port); + return -EINVAL; + } + } + + spin_lock_init(&qe_port->port.lock); + qe_port->np = np; + qe_port->port.dev = &ofdev->dev; + qe_port->port.ops = &qe_uart_pops; + qe_port->port.iotype = UPIO_MEM; + + qe_port->tx_nrfifos = TX_NUM_FIFO; + qe_port->tx_fifosize = TX_BUF_SIZE; + qe_port->rx_nrfifos = RX_NUM_FIFO; + qe_port->rx_fifosize = RX_BUF_SIZE; + + qe_port->wait_closing = UCC_WAIT_CLOSING; + qe_port->port.fifosize = 512; + qe_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP; + + qe_port->us_info.ucc_num = qe_port->ucc_num; + qe_port->us_info.regs = (phys_addr_t) res.start; + qe_port->us_info.irq = qe_port->port.irq; + + qe_port->us_info.rx_bd_ring_len = qe_port->rx_nrfifos; + qe_port->us_info.tx_bd_ring_len = qe_port->tx_nrfifos; + + /* Make sure ucc_slow_init() initializes both TX and RX */ + qe_port->us_info.init_tx = 1; + qe_port->us_info.init_rx = 1; + + /* Add the port to the uart sub-system. This will cause + * qe_uart_config_port() to be called, so the us_info structure must + * be initialized. + */ + ret = uart_add_one_port(&ucc_uart_driver, &qe_port->port); + if (ret) { + dev_err(&ofdev->dev, "could not add /dev/ttyQE%u\n", + qe_port->port.line); + kfree(qe_port); + return ret; + } + + dev_set_drvdata(&ofdev->dev, qe_port); + + dev_info(&ofdev->dev, "UCC%u assigned to /dev/ttyQE%u\n", + qe_port->ucc_num + 1, qe_port->port.line); + + /* Display the mknod command for this device */ + dev_dbg(&ofdev->dev, "mknod command is 'mknod /dev/ttyQE%u c %u %u'\n", + qe_port->port.line, SERIAL_QE_MAJOR, + SERIAL_QE_MINOR + qe_port->port.line); + + return 0; +} + +static int ucc_uart_remove(struct of_device *ofdev) +{ + struct uart_qe_port *qe_port = dev_get_drvdata(&ofdev->dev); + + dev_info(&ofdev->dev, "removing /dev/ttyQE%u\n", qe_port->port.line); + + uart_remove_one_port(&ucc_uart_driver, &qe_port->port); + + dev_set_drvdata(&ofdev->dev, NULL); + kfree(qe_port); + + return 0; +} + +static struct of_device_id ucc_uart_match[] = { + { + .type = "serial", + .compatible = "ucc_uart", + }, + {}, +}; +MODULE_DEVICE_TABLE(of, ucc_uart_match); + +static struct of_platform_driver ucc_uart_of_driver = { + .owner = THIS_MODULE, + .name = "ucc_uart", + .match_table = ucc_uart_match, + .probe = ucc_uart_probe, + .remove = ucc_uart_remove, +}; + +static int __init ucc_uart_init(void) +{ + int ret; + + printk(KERN_INFO "Freescale QUICC Engine UART device driver\n"); +#ifdef LOOPBACK + printk(KERN_INFO "ucc-uart: Using loopback mode\n"); +#endif + + ret = uart_register_driver(&ucc_uart_driver); + if (ret) { + printk(KERN_ERR "ucc-uart: could not register UART driver\n"); + return ret; + } + + ret = of_register_platform_driver(&ucc_uart_of_driver); + if (ret) + printk(KERN_ERR + "ucc-uart: could not register platform driver\n"); + + return ret; +} + +static void __exit ucc_uart_exit(void) +{ + printk(KERN_INFO + "Freescale QUICC Engine UART device driver unloading\n"); + + of_unregister_platform_driver(&ucc_uart_of_driver); + uart_unregister_driver(&ucc_uart_driver); +} + +module_init(ucc_uart_init); +module_exit(ucc_uart_exit); + +MODULE_DESCRIPTION("Freescale QUICC Engine (QE) UART"); +MODULE_AUTHOR("Timur Tabi "); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_QE_MAJOR); + -- cgit v1.1