From 7f514f5c8767b20dbd8706985cdc00a56a9fd280 Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Wed, 2 Jul 2014 12:00:51 +0300 Subject: iwlwifi: mvm: remove unused flags from TX command These flags are not used by the firmware anyway. Signed-off-by: Emmanuel Grumbach --- drivers/net/wireless/iwlwifi/mvm/fw-api-tx.h | 16 ++-------------- 1 file changed, 2 insertions(+), 14 deletions(-) (limited to 'drivers/net/wireless/iwlwifi/mvm/fw-api-tx.h') diff --git a/drivers/net/wireless/iwlwifi/mvm/fw-api-tx.h b/drivers/net/wireless/iwlwifi/mvm/fw-api-tx.h index bdd6ff6..d6073f6 100644 --- a/drivers/net/wireless/iwlwifi/mvm/fw-api-tx.h +++ b/drivers/net/wireless/iwlwifi/mvm/fw-api-tx.h @@ -69,10 +69,8 @@ * @TX_CMD_FLG_ACK: expect ACK from receiving station * @TX_CMD_FLG_STA_RATE: use RS table with initial index from the TX command. * Otherwise, use rate_n_flags from the TX command - * @TX_CMD_FLG_BA: this frame is a block ack * @TX_CMD_FLG_BAR: this frame is a BA request, immediate BAR is expected * Must set TX_CMD_FLG_ACK with this flag. - * @TX_CMD_FLG_TXOP_PROT: protect frame with full TXOP protection * @TX_CMD_FLG_VHT_NDPA: mark frame is NDPA for VHT beamformer sequence * @TX_CMD_FLG_HT_NDPA: mark frame is NDPA for HT beamformer sequence * @TX_CMD_FLG_CSI_FDBK2HOST: mark to send feedback to host (only if good CRC) @@ -82,12 +80,10 @@ * @TX_CMD_FLG_SEQ_CTL: set if FW should override the sequence control. * Should be set for mgmt, non-QOS data, mcast, bcast and in scan command * @TX_CMD_FLG_MORE_FRAG: this frame is non-last MPDU - * @TX_CMD_FLG_NEXT_FRAME: this frame includes information of the next frame * @TX_CMD_FLG_TSF: FW should calculate and insert TSF in the frame * Should be set for beacons and probe responses * @TX_CMD_FLG_CALIB: activate PA TX power calibrations * @TX_CMD_FLG_KEEP_SEQ_CTL: if seq_ctl is set, don't increase inner seq count - * @TX_CMD_FLG_AGG_START: allow this frame to start aggregation * @TX_CMD_FLG_MH_PAD: driver inserted 2 byte padding after MAC header. * Should be set for 26/30 length MAC headers * @TX_CMD_FLG_RESP_TO_DRV: zero this if the response should go only to FW @@ -103,7 +99,6 @@ enum iwl_tx_flags { TX_CMD_FLG_PROT_REQUIRE = BIT(0), TX_CMD_FLG_ACK = BIT(3), TX_CMD_FLG_STA_RATE = BIT(4), - TX_CMD_FLG_BA = BIT(5), TX_CMD_FLG_BAR = BIT(6), TX_CMD_FLG_TXOP_PROT = BIT(7), TX_CMD_FLG_VHT_NDPA = BIT(8), @@ -113,11 +108,9 @@ enum iwl_tx_flags { TX_CMD_FLG_BT_DIS = BIT(12), TX_CMD_FLG_SEQ_CTL = BIT(13), TX_CMD_FLG_MORE_FRAG = BIT(14), - TX_CMD_FLG_NEXT_FRAME = BIT(15), TX_CMD_FLG_TSF = BIT(16), TX_CMD_FLG_CALIB = BIT(17), TX_CMD_FLG_KEEP_SEQ_CTL = BIT(18), - TX_CMD_FLG_AGG_START = BIT(19), TX_CMD_FLG_MH_PAD = BIT(20), TX_CMD_FLG_RESP_TO_DRV = BIT(21), TX_CMD_FLG_CCMP_AGG = BIT(22), @@ -191,8 +184,6 @@ enum iwl_tx_flags { * struct iwl_tx_cmd - TX command struct to FW * ( TX_CMD = 0x1c ) * @len: in bytes of the payload, see below for details - * @next_frame_len: same as len, but for next frame (0 if not applicable) - * Used for fragmentation and bursting, but not in 11n aggregation. * @tx_flags: combination of TX_CMD_FLG_* * @rate_n_flags: rate for *all* Tx attempts, if TX_CMD_FLG_STA_RATE_MSK is * cleared. Combination of RATE_MCS_* @@ -210,8 +201,6 @@ enum iwl_tx_flags { * @data_retry_limit: max attempts to send the data packet * @tid_spec: TID/tspec * @pm_frame_timeout: PM TX frame timeout - * @driver_txop: duration od EDCA TXOP, in 32-usec units. Set this if not - * specified by HCCA protocol * * The byte count (both len and next_frame_len) includes MAC header * (24/26/30/32 bytes) @@ -241,8 +230,7 @@ struct iwl_tx_cmd { u8 initial_rate_index; u8 reserved2; u8 key[16]; - __le16 next_frame_flags; - __le16 reserved3; + __le32 reserved3; __le32 life_time; __le32 dram_lsb_ptr; u8 dram_msb_ptr; @@ -250,7 +238,7 @@ struct iwl_tx_cmd { u8 data_retry_limit; u8 tid_tspec; __le16 pm_frame_timeout; - __le16 driver_txop; + __le16 reserved4; u8 payload[0]; struct ieee80211_hdr hdr[0]; } __packed; /* TX_CMD_API_S_VER_3 */ -- cgit v1.1