From ec21e2ec367697b4803e82662bdff6c8567745fc Mon Sep 17 00:00:00 2001 From: Jeff Kirsher Date: Sat, 11 Jun 2011 02:29:36 -0700 Subject: freescale: Move the Freescale drivers Move the Freescale drivers into drivers/net/ethernet/freescale/ and make the necessary Kconfig and Makefile changes. CC: Sandeep Gopalpet CC: Andy Fleming CC: Shlomi Gridish CC: Li Yang CC: Pantelis Antoniou CC: Vitaly Bordug CC: Dan Malek CC: Sylvain Munaut Signed-off-by: Jeff Kirsher --- drivers/net/Kconfig | 66 ----------------------------------------------------- 1 file changed, 66 deletions(-) (limited to 'drivers/net/Kconfig') diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 27f97b4e..b645a73 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -605,39 +605,6 @@ config NET_POCKET the questions about this class of network devices. If you say Y, you will be asked for your specific device in the following questions. -config FEC - bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)" - depends on M523x || M527x || M5272 || M528x || M520x || M532x || \ - IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC - default IMX_HAVE_PLATFORM_FEC || MXS_HAVE_PLATFORM_FEC if ARM - select PHYLIB - help - Say Y here if you want to use the built-in 10/100 Fast ethernet - controller on some Motorola ColdFire and Freescale i.MX processors. - -config FEC_MPC52xx - tristate "MPC52xx FEC driver" - depends on PPC_MPC52xx && PPC_BESTCOMM - select CRC32 - select PHYLIB - select PPC_BESTCOMM_FEC - ---help--- - This option enables support for the MPC5200's on-chip - Fast Ethernet Controller - If compiled as module, it will be called fec_mpc52xx. - -config FEC_MPC52xx_MDIO - bool "MPC52xx FEC MDIO bus driver" - depends on FEC_MPC52xx - default y - ---help--- - The MPC5200's FEC can connect to the Ethernet either with - an external MII PHY chip or 10 Mbps 7-wire interface - (Motorola? industry standard). - If your board uses an external PHY connected to FEC, enable this. - If not sure, enable. - If compiled as module, it will be called fec_mpc52xx_phy. - config XILINX_EMACLITE tristate "Xilinx 10/100 Ethernet Lite support" depends on PPC32 || MICROBLAZE @@ -651,9 +618,6 @@ config LANTIQ_ETOP help Support for the MII0 inside the Lantiq SoC - -source "drivers/net/fs_enet/Kconfig" - source "drivers/net/octeon/Kconfig" endif # NET_ETHERNET @@ -769,36 +733,6 @@ config GELIC_WIRELESS the driver automatically distinguishes the models, you can safely enable this option even if you have a wireless-less model. -config FSL_PQ_MDIO - tristate "Freescale PQ MDIO" - depends on FSL_SOC - select PHYLIB - help - This driver supports the MDIO bus used by the gianfar and UCC drivers. - -config GIANFAR - tristate "Gianfar Ethernet" - depends on FSL_SOC - select FSL_PQ_MDIO - select PHYLIB - select CRC32 - help - This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, - and MPC86xx family of chips, and the FEC on the 8540. - -config UCC_GETH - tristate "Freescale QE Gigabit Ethernet" - depends on QUICC_ENGINE - select FSL_PQ_MDIO - select PHYLIB - help - This driver supports the Gigabit Ethernet mode of the QUICC Engine, - which is available on some Freescale SOCs. - -config UGETH_TX_ON_DEMAND - bool "Transmit on Demand support" - depends on UCC_GETH - config XILINX_LL_TEMAC tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver" depends on PPC || MICROBLAZE -- cgit v1.1