From a6afd9f3e819de4795fcd356e5bfad446e4323f2 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Tue, 22 Feb 2011 16:14:56 -0800 Subject: tty: move a number of tty drivers from drivers/char/ to drivers/tty/ As planned by Arnd Bergmann, this moves the following drivers from drivers/char/ to drivers/tty/ as that's where they really belong: amiserial nozomi synclink rocket cyclades moxa mxser isicom bfin_jtag_comm Cc: Arnd Bergmann Cc: Alan Cox Cc: Jiri Slaby Signed-off-by: Greg Kroah-Hartman --- drivers/char/cyclades.c | 4200 ----------------------------------------------- 1 file changed, 4200 deletions(-) delete mode 100644 drivers/char/cyclades.c (limited to 'drivers/char/cyclades.c') diff --git a/drivers/char/cyclades.c b/drivers/char/cyclades.c deleted file mode 100644 index c99728f..0000000 --- a/drivers/char/cyclades.c +++ /dev/null @@ -1,4200 +0,0 @@ -#undef BLOCKMOVE -#define Z_WAKE -#undef Z_EXT_CHARS_IN_BUFFER - -/* - * linux/drivers/char/cyclades.c - * - * This file contains the driver for the Cyclades async multiport - * serial boards. - * - * Initially written by Randolph Bentson . - * Modified and maintained by Marcio Saito . - * - * Copyright (C) 2007-2009 Jiri Slaby - * - * Much of the design and some of the code came from serial.c - * which was copyright (C) 1991, 1992 Linus Torvalds. It was - * extensively rewritten by Theodore Ts'o, 8/16/92 -- 9/14/92, - * and then fixed as suggested by Michael K. Johnson 12/12/92. - * Converted to pci probing and cleaned up by Jiri Slaby. - * - */ - -#define CY_VERSION "2.6" - -/* If you need to install more boards than NR_CARDS, change the constant - in the definition below. No other change is necessary to support up to - eight boards. Beyond that you'll have to extend cy_isa_addresses. */ - -#define NR_CARDS 4 - -/* - If the total number of ports is larger than NR_PORTS, change this - constant in the definition below. No other change is necessary to - support more boards/ports. */ - -#define NR_PORTS 256 - -#define ZO_V1 0 -#define ZO_V2 1 -#define ZE_V1 2 - -#define SERIAL_PARANOIA_CHECK -#undef CY_DEBUG_OPEN -#undef CY_DEBUG_THROTTLE -#undef CY_DEBUG_OTHER -#undef CY_DEBUG_IO -#undef CY_DEBUG_COUNT -#undef CY_DEBUG_DTR -#undef CY_DEBUG_WAIT_UNTIL_SENT -#undef CY_DEBUG_INTERRUPTS -#undef CY_16Y_HACK -#undef CY_ENABLE_MONITORING -#undef CY_PCI_DEBUG - -/* - * Include section - */ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include - -#include -#include - -#include -#include -#include - -static void cy_send_xchar(struct tty_struct *tty, char ch); - -#ifndef SERIAL_XMIT_SIZE -#define SERIAL_XMIT_SIZE (min(PAGE_SIZE, 4096)) -#endif - -#define STD_COM_FLAGS (0) - -/* firmware stuff */ -#define ZL_MAX_BLOCKS 16 -#define DRIVER_VERSION 0x02010203 -#define RAM_SIZE 0x80000 - -enum zblock_type { - ZBLOCK_PRG = 0, - ZBLOCK_FPGA = 1 -}; - -struct zfile_header { - char name[64]; - char date[32]; - char aux[32]; - u32 n_config; - u32 config_offset; - u32 n_blocks; - u32 block_offset; - u32 reserved[9]; -} __attribute__ ((packed)); - -struct zfile_config { - char name[64]; - u32 mailbox; - u32 function; - u32 n_blocks; - u32 block_list[ZL_MAX_BLOCKS]; -} __attribute__ ((packed)); - -struct zfile_block { - u32 type; - u32 file_offset; - u32 ram_offset; - u32 size; -} __attribute__ ((packed)); - -static struct tty_driver *cy_serial_driver; - -#ifdef CONFIG_ISA -/* This is the address lookup table. The driver will probe for - Cyclom-Y/ISA boards at all addresses in here. If you want the - driver to probe addresses at a different address, add it to - this table. If the driver is probing some other board and - causing problems, remove the offending address from this table. -*/ - -static unsigned int cy_isa_addresses[] = { - 0xD0000, - 0xD2000, - 0xD4000, - 0xD6000, - 0xD8000, - 0xDA000, - 0xDC000, - 0xDE000, - 0, 0, 0, 0, 0, 0, 0, 0 -}; - -#define NR_ISA_ADDRS ARRAY_SIZE(cy_isa_addresses) - -static long maddr[NR_CARDS]; -static int irq[NR_CARDS]; - -module_param_array(maddr, long, NULL, 0); -module_param_array(irq, int, NULL, 0); - -#endif /* CONFIG_ISA */ - -/* This is the per-card data structure containing address, irq, number of - channels, etc. This driver supports a maximum of NR_CARDS cards. -*/ -static struct cyclades_card cy_card[NR_CARDS]; - -static int cy_next_channel; /* next minor available */ - -/* - * This is used to look up the divisor speeds and the timeouts - * We're normally limited to 15 distinct baud rates. The extra - * are accessed via settings in info->port.flags. - * 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, - * 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, - * HI VHI - * 20 - */ -static const int baud_table[] = { - 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, - 1800, 2400, 4800, 9600, 19200, 38400, 57600, 76800, 115200, 150000, - 230400, 0 -}; - -static const char baud_co_25[] = { /* 25 MHz clock option table */ - /* value => 00 01 02 03 04 */ - /* divide by 8 32 128 512 2048 */ - 0x00, 0x04, 0x04, 0x04, 0x04, 0x04, 0x03, 0x03, 0x03, 0x02, - 0x02, 0x02, 0x01, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 -}; - -static const char baud_bpr_25[] = { /* 25 MHz baud rate period table */ - 0x00, 0xf5, 0xa3, 0x6f, 0x5c, 0x51, 0xf5, 0xa3, 0x51, 0xa3, - 0x6d, 0x51, 0xa3, 0x51, 0xa3, 0x51, 0x36, 0x29, 0x1b, 0x15 -}; - -static const char baud_co_60[] = { /* 60 MHz clock option table (CD1400 J) */ - /* value => 00 01 02 03 04 */ - /* divide by 8 32 128 512 2048 */ - 0x00, 0x00, 0x00, 0x04, 0x04, 0x04, 0x04, 0x04, 0x03, 0x03, - 0x03, 0x02, 0x02, 0x01, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, - 0x00 -}; - -static const char baud_bpr_60[] = { /* 60 MHz baud rate period table (CD1400 J) */ - 0x00, 0x82, 0x21, 0xff, 0xdb, 0xc3, 0x92, 0x62, 0xc3, 0x62, - 0x41, 0xc3, 0x62, 0xc3, 0x62, 0xc3, 0x82, 0x62, 0x41, 0x32, - 0x21 -}; - -static const char baud_cor3[] = { /* receive threshold */ - 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, - 0x0a, 0x0a, 0x0a, 0x09, 0x09, 0x08, 0x08, 0x08, 0x08, 0x07, - 0x07 -}; - -/* - * The Cyclades driver implements HW flow control as any serial driver. - * The cyclades_port structure member rflow and the vector rflow_thr - * allows us to take advantage of a special feature in the CD1400 to avoid - * data loss even when the system interrupt latency is too high. These flags - * are to be used only with very special applications. Setting these flags - * requires the use of a special cable (DTR and RTS reversed). In the new - * CD1400-based boards (rev. 6.00 or later), there is no need for special - * cables. - */ - -static const char rflow_thr[] = { /* rflow threshold */ - 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, - 0x00, 0x00, 0x00, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, 0x0a, - 0x0a -}; - -/* The Cyclom-Ye has placed the sequential chips in non-sequential - * address order. This look-up table overcomes that problem. - */ -static const unsigned int cy_chip_offset[] = { 0x0000, - 0x0400, - 0x0800, - 0x0C00, - 0x0200, - 0x0600, - 0x0A00, - 0x0E00 -}; - -/* PCI related definitions */ - -#ifdef CONFIG_PCI -static const struct pci_device_id cy_pci_dev_id[] = { - /* PCI < 1Mb */ - { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Lo) }, - /* PCI > 1Mb */ - { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Y_Hi) }, - /* 4Y PCI < 1Mb */ - { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_4Y_Lo) }, - /* 4Y PCI > 1Mb */ - { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_4Y_Hi) }, - /* 8Y PCI < 1Mb */ - { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_8Y_Lo) }, - /* 8Y PCI > 1Mb */ - { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_8Y_Hi) }, - /* Z PCI < 1Mb */ - { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Z_Lo) }, - /* Z PCI > 1Mb */ - { PCI_DEVICE(PCI_VENDOR_ID_CYCLADES, PCI_DEVICE_ID_CYCLOM_Z_Hi) }, - { } /* end of table */ -}; -MODULE_DEVICE_TABLE(pci, cy_pci_dev_id); -#endif - -static void cy_start(struct tty_struct *); -static void cy_set_line_char(struct cyclades_port *, struct tty_struct *); -static int cyz_issue_cmd(struct cyclades_card *, __u32, __u8, __u32); -#ifdef CONFIG_ISA -static unsigned detect_isa_irq(void __iomem *); -#endif /* CONFIG_ISA */ - -#ifndef CONFIG_CYZ_INTR -static void cyz_poll(unsigned long); - -/* The Cyclades-Z polling cycle is defined by this variable */ -static long cyz_polling_cycle = CZ_DEF_POLL; - -static DEFINE_TIMER(cyz_timerlist, cyz_poll, 0, 0); - -#else /* CONFIG_CYZ_INTR */ -static void cyz_rx_restart(unsigned long); -static struct timer_list cyz_rx_full_timer[NR_PORTS]; -#endif /* CONFIG_CYZ_INTR */ - -static inline void cyy_writeb(struct cyclades_port *port, u32 reg, u8 val) -{ - struct cyclades_card *card = port->card; - - cy_writeb(port->u.cyy.base_addr + (reg << card->bus_index), val); -} - -static inline u8 cyy_readb(struct cyclades_port *port, u32 reg) -{ - struct cyclades_card *card = port->card; - - return readb(port->u.cyy.base_addr + (reg << card->bus_index)); -} - -static inline bool cy_is_Z(struct cyclades_card *card) -{ - return card->num_chips == (unsigned int)-1; -} - -static inline bool __cyz_fpga_loaded(struct RUNTIME_9060 __iomem *ctl_addr) -{ - return readl(&ctl_addr->init_ctrl) & (1 << 17); -} - -static inline bool cyz_fpga_loaded(struct cyclades_card *card) -{ - return __cyz_fpga_loaded(card->ctl_addr.p9060); -} - -static inline bool cyz_is_loaded(struct cyclades_card *card) -{ - struct FIRM_ID __iomem *fw_id = card->base_addr + ID_ADDRESS; - - return (card->hw_ver == ZO_V1 || cyz_fpga_loaded(card)) && - readl(&fw_id->signature) == ZFIRM_ID; -} - -static inline int serial_paranoia_check(struct cyclades_port *info, - const char *name, const char *routine) -{ -#ifdef SERIAL_PARANOIA_CHECK - if (!info) { - printk(KERN_WARNING "cyc Warning: null cyclades_port for (%s) " - "in %s\n", name, routine); - return 1; - } - - if (info->magic != CYCLADES_MAGIC) { - printk(KERN_WARNING "cyc Warning: bad magic number for serial " - "struct (%s) in %s\n", name, routine); - return 1; - } -#endif - return 0; -} - -/***********************************************************/ -/********* Start of block of Cyclom-Y specific code ********/ - -/* This routine waits up to 1000 micro-seconds for the previous - command to the Cirrus chip to complete and then issues the - new command. An error is returned if the previous command - didn't finish within the time limit. - - This function is only called from inside spinlock-protected code. - */ -static int __cyy_issue_cmd(void __iomem *base_addr, u8 cmd, int index) -{ - void __iomem *ccr = base_addr + (CyCCR << index); - unsigned int i; - - /* Check to see that the previous command has completed */ - for (i = 0; i < 100; i++) { - if (readb(ccr) == 0) - break; - udelay(10L); - } - /* if the CCR never cleared, the previous command - didn't finish within the "reasonable time" */ - if (i == 100) - return -1; - - /* Issue the new command */ - cy_writeb(ccr, cmd); - - return 0; -} - -static inline int cyy_issue_cmd(struct cyclades_port *port, u8 cmd) -{ - return __cyy_issue_cmd(port->u.cyy.base_addr, cmd, - port->card->bus_index); -} - -#ifdef CONFIG_ISA -/* ISA interrupt detection code */ -static unsigned detect_isa_irq(void __iomem *address) -{ - int irq; - unsigned long irqs, flags; - int save_xir, save_car; - int index = 0; /* IRQ probing is only for ISA */ - - /* forget possible initially masked and pending IRQ */ - irq = probe_irq_off(probe_irq_on()); - - /* Clear interrupts on the board first */ - cy_writeb(address + (Cy_ClrIntr << index), 0); - /* Cy_ClrIntr is 0x1800 */ - - irqs = probe_irq_on(); - /* Wait ... */ - msleep(5); - - /* Enable the Tx interrupts on the CD1400 */ - local_irq_save(flags); - cy_writeb(address + (CyCAR << index), 0); - __cyy_issue_cmd(address, CyCHAN_CTL | CyENB_XMTR, index); - - cy_writeb(address + (CyCAR << index), 0); - cy_writeb(address + (CySRER << index), - readb(address + (CySRER << index)) | CyTxRdy); - local_irq_restore(flags); - - /* Wait ... */ - msleep(5); - - /* Check which interrupt is in use */ - irq = probe_irq_off(irqs); - - /* Clean up */ - save_xir = (u_char) readb(address + (CyTIR << index)); - save_car = readb(address + (CyCAR << index)); - cy_writeb(address + (CyCAR << index), (save_xir & 0x3)); - cy_writeb(address + (CySRER << index), - readb(address + (CySRER << index)) & ~CyTxRdy); - cy_writeb(address + (CyTIR << index), (save_xir & 0x3f)); - cy_writeb(address + (CyCAR << index), (save_car)); - cy_writeb(address + (Cy_ClrIntr << index), 0); - /* Cy_ClrIntr is 0x1800 */ - - return (irq > 0) ? irq : 0; -} -#endif /* CONFIG_ISA */ - -static void cyy_chip_rx(struct cyclades_card *cinfo, int chip, - void __iomem *base_addr) -{ - struct cyclades_port *info; - struct tty_struct *tty; - int len, index = cinfo->bus_index; - u8 ivr, save_xir, channel, save_car, data, char_count; - -#ifdef CY_DEBUG_INTERRUPTS - printk(KERN_DEBUG "cyy_interrupt: rcvd intr, chip %d\n", chip); -#endif - /* determine the channel & change to that context */ - save_xir = readb(base_addr + (CyRIR << index)); - channel = save_xir & CyIRChannel; - info = &cinfo->ports[channel + chip * 4]; - save_car = cyy_readb(info, CyCAR); - cyy_writeb(info, CyCAR, save_xir); - ivr = cyy_readb(info, CyRIVR) & CyIVRMask; - - tty = tty_port_tty_get(&info->port); - /* if there is nowhere to put the data, discard it */ - if (tty == NULL) { - if (ivr == CyIVRRxEx) { /* exception */ - data = cyy_readb(info, CyRDSR); - } else { /* normal character reception */ - char_count = cyy_readb(info, CyRDCR); - while (char_count--) - data = cyy_readb(info, CyRDSR); - } - goto end; - } - /* there is an open port for this data */ - if (ivr == CyIVRRxEx) { /* exception */ - data = cyy_readb(info, CyRDSR); - - /* For statistics only */ - if (data & CyBREAK) - info->icount.brk++; - else if (data & CyFRAME) - info->icount.frame++; - else if (data & CyPARITY) - info->icount.parity++; - else if (data & CyOVERRUN) - info->icount.overrun++; - - if (data & info->ignore_status_mask) { - info->icount.rx++; - tty_kref_put(tty); - return; - } - if (tty_buffer_request_room(tty, 1)) { - if (data & info->read_status_mask) { - if (data & CyBREAK) { - tty_insert_flip_char(tty, - cyy_readb(info, CyRDSR), - TTY_BREAK); - info->icount.rx++; - if (info->port.flags & ASYNC_SAK) - do_SAK(tty); - } else if (data & CyFRAME) { - tty_insert_flip_char(tty, - cyy_readb(info, CyRDSR), - TTY_FRAME); - info->icount.rx++; - info->idle_stats.frame_errs++; - } else if (data & CyPARITY) { - /* Pieces of seven... */ - tty_insert_flip_char(tty, - cyy_readb(info, CyRDSR), - TTY_PARITY); - info->icount.rx++; - info->idle_stats.parity_errs++; - } else if (data & CyOVERRUN) { - tty_insert_flip_char(tty, 0, - TTY_OVERRUN); - info->icount.rx++; - /* If the flip buffer itself is - overflowing, we still lose - the next incoming character. - */ - tty_insert_flip_char(tty, - cyy_readb(info, CyRDSR), - TTY_FRAME); - info->icount.rx++; - info->idle_stats.overruns++; - /* These two conditions may imply */ - /* a normal read should be done. */ - /* } else if(data & CyTIMEOUT) { */ - /* } else if(data & CySPECHAR) { */ - } else { - tty_insert_flip_char(tty, 0, - TTY_NORMAL); - info->icount.rx++; - } - } else { - tty_insert_flip_char(tty, 0, TTY_NORMAL); - info->icount.rx++; - } - } else { - /* there was a software buffer overrun and nothing - * could be done about it!!! */ - info->icount.buf_overrun++; - info->idle_stats.overruns++; - } - } else { /* normal character reception */ - /* load # chars available from the chip */ - char_count = cyy_readb(info, CyRDCR); - -#ifdef CY_ENABLE_MONITORING - ++info->mon.int_count; - info->mon.char_count += char_count; - if (char_count > info->mon.char_max) - info->mon.char_max = char_count; - info->mon.char_last = char_count; -#endif - len = tty_buffer_request_room(tty, char_count); - while (len--) { - data = cyy_readb(info, CyRDSR); - tty_insert_flip_char(tty, data, TTY_NORMAL); - info->idle_stats.recv_bytes++; - info->icount.rx++; -#ifdef CY_16Y_HACK - udelay(10L); -#endif - } - info->idle_stats.recv_idle = jiffies; - } - tty_schedule_flip(tty); - tty_kref_put(tty); -end: - /* end of service */ - cyy_writeb(info, CyRIR, save_xir & 0x3f); - cyy_writeb(info, CyCAR, save_car); -} - -static void cyy_chip_tx(struct cyclades_card *cinfo, unsigned int chip, - void __iomem *base_addr) -{ - struct cyclades_port *info; - struct tty_struct *tty; - int char_count, index = cinfo->bus_index; - u8 save_xir, channel, save_car, outch; - - /* Since we only get here when the transmit buffer - is empty, we know we can always stuff a dozen - characters. */ -#ifdef CY_DEBUG_INTERRUPTS - printk(KERN_DEBUG "cyy_interrupt: xmit intr, chip %d\n", chip); -#endif - - /* determine the channel & change to that context */ - save_xir = readb(base_addr + (CyTIR << index)); - channel = save_xir & CyIRChannel; - save_car = readb(base_addr + (CyCAR << index)); - cy_writeb(base_addr + (CyCAR << index), save_xir); - - info = &cinfo->ports[channel + chip * 4]; - tty = tty_port_tty_get(&info->port); - if (tty == NULL) { - cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyTxRdy); - goto end; - } - - /* load the on-chip space for outbound data */ - char_count = info->xmit_fifo_size; - - if (info->x_char) { /* send special char */ - outch = info->x_char; - cyy_writeb(info, CyTDR, outch); - char_count--; - info->icount.tx++; - info->x_char = 0; - } - - if (info->breakon || info->breakoff) { - if (info->breakon) { - cyy_writeb(info, CyTDR, 0); - cyy_writeb(info, CyTDR, 0x81); - info->breakon = 0; - char_count -= 2; - } - if (info->breakoff) { - cyy_writeb(info, CyTDR, 0); - cyy_writeb(info, CyTDR, 0x83); - info->breakoff = 0; - char_count -= 2; - } - } - - while (char_count-- > 0) { - if (!info->xmit_cnt) { - if (cyy_readb(info, CySRER) & CyTxMpty) { - cyy_writeb(info, CySRER, - cyy_readb(info, CySRER) & ~CyTxMpty); - } else { - cyy_writeb(info, CySRER, CyTxMpty | - (cyy_readb(info, CySRER) & ~CyTxRdy)); - } - goto done; - } - if (info->port.xmit_buf == NULL) { - cyy_writeb(info, CySRER, - cyy_readb(info, CySRER) & ~CyTxRdy); - goto done; - } - if (tty->stopped || tty->hw_stopped) { - cyy_writeb(info, CySRER, - cyy_readb(info, CySRER) & ~CyTxRdy); - goto done; - } - /* Because the Embedded Transmit Commands have been enabled, - * we must check to see if the escape character, NULL, is being - * sent. If it is, we must ensure that there is room for it to - * be doubled in the output stream. Therefore we no longer - * advance the pointer when the character is fetched, but - * rather wait until after the check for a NULL output - * character. This is necessary because there may not be room - * for the two chars needed to send a NULL.) - */ - outch = info->port.xmit_buf[info->xmit_tail]; - if (outch) { - info->xmit_cnt--; - info->xmit_tail = (info->xmit_tail + 1) & - (SERIAL_XMIT_SIZE - 1); - cyy_writeb(info, CyTDR, outch); - info->icount.tx++; - } else { - if (char_count > 1) { - info->xmit_cnt--; - info->xmit_tail = (info->xmit_tail + 1) & - (SERIAL_XMIT_SIZE - 1); - cyy_writeb(info, CyTDR, outch); - cyy_writeb(info, CyTDR, 0); - info->icount.tx++; - char_count--; - } - } - } - -done: - tty_wakeup(tty); - tty_kref_put(tty); -end: - /* end of service */ - cyy_writeb(info, CyTIR, save_xir & 0x3f); - cyy_writeb(info, CyCAR, save_car); -} - -static void cyy_chip_modem(struct cyclades_card *cinfo, int chip, - void __iomem *base_addr) -{ - struct cyclades_port *info; - struct tty_struct *tty; - int index = cinfo->bus_index; - u8 save_xir, channel, save_car, mdm_change, mdm_status; - - /* determine the channel & change to that context */ - save_xir = readb(base_addr + (CyMIR << index)); - channel = save_xir & CyIRChannel; - info = &cinfo->ports[channel + chip * 4]; - save_car = cyy_readb(info, CyCAR); - cyy_writeb(info, CyCAR, save_xir); - - mdm_change = cyy_readb(info, CyMISR); - mdm_status = cyy_readb(info, CyMSVR1); - - tty = tty_port_tty_get(&info->port); - if (!tty) - goto end; - - if (mdm_change & CyANY_DELTA) { - /* For statistics only */ - if (mdm_change & CyDCD) - info->icount.dcd++; - if (mdm_change & CyCTS) - info->icount.cts++; - if (mdm_change & CyDSR) - info->icount.dsr++; - if (mdm_change & CyRI) - info->icount.rng++; - - wake_up_interruptible(&info->port.delta_msr_wait); - } - - if ((mdm_change & CyDCD) && (info->port.flags & ASYNC_CHECK_CD)) { - if (mdm_status & CyDCD) - wake_up_interruptible(&info->port.open_wait); - else - tty_hangup(tty); - } - if ((mdm_change & CyCTS) && (info->port.flags & ASYNC_CTS_FLOW)) { - if (tty->hw_stopped) { - if (mdm_status & CyCTS) { - /* cy_start isn't used - because... !!! */ - tty->hw_stopped = 0; - cyy_writeb(info, CySRER, - cyy_readb(info, CySRER) | CyTxRdy); - tty_wakeup(tty); - } - } else { - if (!(mdm_status & CyCTS)) { - /* cy_stop isn't used - because ... !!! */ - tty->hw_stopped = 1; - cyy_writeb(info, CySRER, - cyy_readb(info, CySRER) & ~CyTxRdy); - } - } - } -/* if (mdm_change & CyDSR) { - } - if (mdm_change & CyRI) { - }*/ - tty_kref_put(tty); -end: - /* end of service */ - cyy_writeb(info, CyMIR, save_xir & 0x3f); - cyy_writeb(info, CyCAR, save_car); -} - -/* The real interrupt service routine is called - whenever the card wants its hand held--chars - received, out buffer empty, modem change, etc. - */ -static irqreturn_t cyy_interrupt(int irq, void *dev_id) -{ - int status; - struct cyclades_card *cinfo = dev_id; - void __iomem *base_addr, *card_base_addr; - unsigned int chip, too_many, had_work; - int index; - - if (unlikely(cinfo == NULL)) { -#ifdef CY_DEBUG_INTERRUPTS - printk(KERN_DEBUG "cyy_interrupt: spurious interrupt %d\n", - irq); -#endif - return IRQ_NONE; /* spurious interrupt */ - } - - card_base_addr = cinfo->base_addr; - index = cinfo->bus_index; - - /* card was not initialized yet (e.g. DEBUG_SHIRQ) */ - if (unlikely(card_base_addr == NULL)) - return IRQ_HANDLED; - - /* This loop checks all chips in the card. Make a note whenever - _any_ chip had some work to do, as this is considered an - indication that there will be more to do. Only when no chip - has any work does this outermost loop exit. - */ - do { - had_work = 0; - for (chip = 0; chip < cinfo->num_chips; chip++) { - base_addr = cinfo->base_addr + - (cy_chip_offset[chip] << index); - too_many = 0; - while ((status = readb(base_addr + - (CySVRR << index))) != 0x00) { - had_work++; - /* The purpose of the following test is to ensure that - no chip can monopolize the driver. This forces the - chips to be checked in a round-robin fashion (after - draining each of a bunch (1000) of characters). - */ - if (1000 < too_many++) - break; - spin_lock(&cinfo->card_lock); - if (status & CySRReceive) /* rx intr */ - cyy_chip_rx(cinfo, chip, base_addr); - if (status & CySRTransmit) /* tx intr */ - cyy_chip_tx(cinfo, chip, base_addr); - if (status & CySRModem) /* modem intr */ - cyy_chip_modem(cinfo, chip, base_addr); - spin_unlock(&cinfo->card_lock); - } - } - } while (had_work); - - /* clear interrupts */ - spin_lock(&cinfo->card_lock); - cy_writeb(card_base_addr + (Cy_ClrIntr << index), 0); - /* Cy_ClrIntr is 0x1800 */ - spin_unlock(&cinfo->card_lock); - return IRQ_HANDLED; -} /* cyy_interrupt */ - -static void cyy_change_rts_dtr(struct cyclades_port *info, unsigned int set, - unsigned int clear) -{ - struct cyclades_card *card = info->card; - int channel = info->line - card->first_line; - u32 rts, dtr, msvrr, msvrd; - - channel &= 0x03; - - if (info->rtsdtr_inv) { - msvrr = CyMSVR2; - msvrd = CyMSVR1; - rts = CyDTR; - dtr = CyRTS; - } else { - msvrr = CyMSVR1; - msvrd = CyMSVR2; - rts = CyRTS; - dtr = CyDTR; - } - if (set & TIOCM_RTS) { - cyy_writeb(info, CyCAR, channel); - cyy_writeb(info, msvrr, rts); - } - if (clear & TIOCM_RTS) { - cyy_writeb(info, CyCAR, channel); - cyy_writeb(info, msvrr, ~rts); - } - if (set & TIOCM_DTR) { - cyy_writeb(info, CyCAR, channel); - cyy_writeb(info, msvrd, dtr); -#ifdef CY_DEBUG_DTR - printk(KERN_DEBUG "cyc:set_modem_info raising DTR\n"); - printk(KERN_DEBUG " status: 0x%x, 0x%x\n", - cyy_readb(info, CyMSVR1), - cyy_readb(info, CyMSVR2)); -#endif - } - if (clear & TIOCM_DTR) { - cyy_writeb(info, CyCAR, channel); - cyy_writeb(info, msvrd, ~dtr); -#ifdef CY_DEBUG_DTR - printk(KERN_DEBUG "cyc:set_modem_info dropping DTR\n"); - printk(KERN_DEBUG " status: 0x%x, 0x%x\n", - cyy_readb(info, CyMSVR1), - cyy_readb(info, CyMSVR2)); -#endif - } -} - -/***********************************************************/ -/********* End of block of Cyclom-Y specific code **********/ -/******** Start of block of Cyclades-Z specific code *******/ -/***********************************************************/ - -static int -cyz_fetch_msg(struct cyclades_card *cinfo, - __u32 *channel, __u8 *cmd, __u32 *param) -{ - struct BOARD_CTRL __iomem *board_ctrl = cinfo->board_ctrl; - unsigned long loc_doorbell; - - loc_doorbell = readl(&cinfo->ctl_addr.p9060->loc_doorbell); - if (loc_doorbell) { - *cmd = (char)(0xff & loc_doorbell); - *channel = readl(&board_ctrl->fwcmd_channel); - *param = (__u32) readl(&board_ctrl->fwcmd_param); - cy_writel(&cinfo->ctl_addr.p9060->loc_doorbell, 0xffffffff); - return 1; - } - return 0; -} /* cyz_fetch_msg */ - -static int -cyz_issue_cmd(struct cyclades_card *cinfo, - __u32 channel, __u8 cmd, __u32 param) -{ - struct BOARD_CTRL __iomem *board_ctrl = cinfo->board_ctrl; - __u32 __iomem *pci_doorbell; - unsigned int index; - - if (!cyz_is_loaded(cinfo)) - return -1; - - index = 0; - pci_doorbell = &cinfo->ctl_addr.p9060->pci_doorbell; - while ((readl(pci_doorbell) & 0xff) != 0) { - if (index++ == 1000) - return (int)(readl(pci_doorbell) & 0xff); - udelay(50L); - } - cy_writel(&board_ctrl->hcmd_channel, channel); - cy_writel(&board_ctrl->hcmd_param, param); - cy_writel(pci_doorbell, (long)cmd); - - return 0; -} /* cyz_issue_cmd */ - -static void cyz_handle_rx(struct cyclades_port *info, struct tty_struct *tty) -{ - struct BUF_CTRL __iomem *buf_ctrl = info->u.cyz.buf_ctrl; - struct cyclades_card *cinfo = info->card; - unsigned int char_count; - int len; -#ifdef BLOCKMOVE - unsigned char *buf; -#else - char data; -#endif - __u32 rx_put, rx_get, new_rx_get, rx_bufsize, rx_bufaddr; - - rx_get = new_rx_get = readl(&buf_ctrl->rx_get); - rx_put = readl(&buf_ctrl->rx_put); - rx_bufsize = readl(&buf_ctrl->rx_bufsize); - rx_bufaddr = readl(&buf_ctrl->rx_bufaddr); - if (rx_put >= rx_get) - char_count = rx_put - rx_get; - else - char_count = rx_put - rx_get + rx_bufsize; - - if (char_count) { -#ifdef CY_ENABLE_MONITORING - info->mon.int_count++; - info->mon.char_count += char_count; - if (char_count > info->mon.char_max) - info->mon.char_max = char_count; - info->mon.char_last = char_count; -#endif - if (tty == NULL) { - /* flush received characters */ - new_rx_get = (new_rx_get + char_count) & - (rx_bufsize - 1); - info->rflush_count++; - } else { -#ifdef BLOCKMOVE - /* we'd like to use memcpy(t, f, n) and memset(s, c, count) - for performance, but because of buffer boundaries, there - may be several steps to the operation */ - while (1) { - len = tty_prepare_flip_string(tty, &buf, - char_count); - if (!len) - break; - - len = min_t(unsigned int, min(len, char_count), - rx_bufsize - new_rx_get); - - memcpy_fromio(buf, cinfo->base_addr + - rx_bufaddr + new_rx_get, len); - - new_rx_get = (new_rx_get + len) & - (rx_bufsize - 1); - char_count -= len; - info->icount.rx += len; - info->idle_stats.recv_bytes += len; - } -#else - len = tty_buffer_request_room(tty, char_count); - while (len--) { - data = readb(cinfo->base_addr + rx_bufaddr + - new_rx_get); - new_rx_get = (new_rx_get + 1) & - (rx_bufsize - 1); - tty_insert_flip_char(tty, data, TTY_NORMAL); - info->idle_stats.recv_bytes++; - info->icount.rx++; - } -#endif -#ifdef CONFIG_CYZ_INTR - /* Recalculate the number of chars in the RX buffer and issue - a cmd in case it's higher than the RX high water mark */ - rx_put = readl(&buf_ctrl->rx_put); - if (rx_put >= rx_get) - char_count = rx_put - rx_get; - else - char_count = rx_put - rx_get + rx_bufsize; - if (char_count >= readl(&buf_ctrl->rx_threshold) && - !timer_pending(&cyz_rx_full_timer[ - info->line])) - mod_timer(&cyz_rx_full_timer[info->line], - jiffies + 1); -#endif - info->idle_stats.recv_idle = jiffies; - tty_schedule_flip(tty); - } - /* Update rx_get */ - cy_writel(&buf_ctrl->rx_get, new_rx_get); - } -} - -static void cyz_handle_tx(struct cyclades_port *info, struct tty_struct *tty) -{ - struct BUF_CTRL __iomem *buf_ctrl = info->u.cyz.buf_ctrl; - struct cyclades_card *cinfo = info->card; - u8 data; - unsigned int char_count; -#ifdef BLOCKMOVE - int small_count; -#endif - __u32 tx_put, tx_get, tx_bufsize, tx_bufaddr; - - if (info->xmit_cnt <= 0) /* Nothing to transmit */ - return; - - tx_get = readl(&buf_ctrl->tx_get); - tx_put = readl(&buf_ctrl->tx_put); - tx_bufsize = readl(&buf_ctrl->tx_bufsize); - tx_bufaddr = readl(&buf_ctrl->tx_bufaddr); - if (tx_put >= tx_get) - char_count = tx_get - tx_put - 1 + tx_bufsize; - else - char_count = tx_get - tx_put - 1; - - if (char_count) { - - if (tty == NULL) - goto ztxdone; - - if (info->x_char) { /* send special char */ - data = info->x_char; - - cy_writeb(cinfo->base_addr + tx_bufaddr + tx_put, data); - tx_put = (tx_put + 1) & (tx_bufsize - 1); - info->x_char = 0; - char_count--; - info->icount.tx++; - } -#ifdef BLOCKMOVE - while (0 < (small_count = min_t(unsigned int, - tx_bufsize - tx_put, min_t(unsigned int, - (SERIAL_XMIT_SIZE - info->xmit_tail), - min_t(unsigned int, info->xmit_cnt, - char_count))))) { - - memcpy_toio((char *)(cinfo->base_addr + tx_bufaddr + - tx_put), - &info->port.xmit_buf[info->xmit_tail], - small_count); - - tx_put = (tx_put + small_count) & (tx_bufsize - 1); - char_count -= small_count; - info->icount.tx += small_count; - info->xmit_cnt -= small_count; - info->xmit_tail = (info->xmit_tail + small_count) & - (SERIAL_XMIT_SIZE - 1); - } -#else - while (info->xmit_cnt && char_count) { - data = info->port.xmit_buf[info->xmit_tail]; - info->xmit_cnt--; - info->xmit_tail = (info->xmit_tail + 1) & - (SERIAL_XMIT_SIZE - 1); - - cy_writeb(cinfo->base_addr + tx_bufaddr + tx_put, data); - tx_put = (tx_put + 1) & (tx_bufsize - 1); - char_count--; - info->icount.tx++; - } -#endif - tty_wakeup(tty); -ztxdone: - /* Update tx_put */ - cy_writel(&buf_ctrl->tx_put, tx_put); - } -} - -static void cyz_handle_cmd(struct cyclades_card *cinfo) -{ - struct BOARD_CTRL __iomem *board_ctrl = cinfo->board_ctrl; - struct tty_struct *tty; - struct cyclades_port *info; - __u32 channel, param, fw_ver; - __u8 cmd; - int special_count; - int delta_count; - - fw_ver = readl(&board_ctrl->fw_version); - - while (cyz_fetch_msg(cinfo, &channel, &cmd, ¶m) == 1) { - special_count = 0; - delta_count = 0; - info = &cinfo->ports[channel]; - tty = tty_port_tty_get(&info->port); - if (tty == NULL) - continue; - - switch (cmd) { - case C_CM_PR_ERROR: - tty_insert_flip_char(tty, 0, TTY_PARITY); - info->icount.rx++; - special_count++; - break; - case C_CM_FR_ERROR: - tty_insert_flip_char(tty, 0, TTY_FRAME); - info->icount.rx++; - special_count++; - break; - case C_CM_RXBRK: - tty_insert_flip_char(tty, 0, TTY_BREAK); - info->icount.rx++; - special_count++; - break; - case C_CM_MDCD: - info->icount.dcd++; - delta_count++; - if (info->port.flags & ASYNC_CHECK_CD) { - u32 dcd = fw_ver > 241 ? param : - readl(&info->u.cyz.ch_ctrl->rs_status); - if (dcd & C_RS_DCD) - wake_up_interruptible(&info->port.open_wait); - else - tty_hangup(tty); - } - break; - case C_CM_MCTS: - info->icount.cts++; - delta_count++; - break; - case C_CM_MRI: - info->icount.rng++; - delta_count++; - break; - case C_CM_MDSR: - info->icount.dsr++; - delta_count++; - break; -#ifdef Z_WAKE - case C_CM_IOCTLW: - complete(&info->shutdown_wait); - break; -#endif -#ifdef CONFIG_CYZ_INTR - case C_CM_RXHIWM: - case C_CM_RXNNDT: - case C_CM_INTBACK2: - /* Reception Interrupt */ -#ifdef CY_DEBUG_INTERRUPTS - printk(KERN_DEBUG "cyz_interrupt: rcvd intr, card %d, " - "port %ld\n", info->card, channel); -#endif - cyz_handle_rx(info, tty); - break; - case C_CM_TXBEMPTY: - case C_CM_TXLOWWM: - case C_CM_INTBACK: - /* Transmission Interrupt */ -#ifdef CY_DEBUG_INTERRUPTS - printk(KERN_DEBUG "cyz_interrupt: xmit intr, card %d, " - "port %ld\n", info->card, channel); -#endif - cyz_handle_tx(info, tty); - break; -#endif /* CONFIG_CYZ_INTR */ - case C_CM_FATAL: - /* should do something with this !!! */ - break; - default: - break; - } - if (delta_count) - wake_up_interruptible(&info->port.delta_msr_wait); - if (special_count) - tty_schedule_flip(tty); - tty_kref_put(tty); - } -} - -#ifdef CONFIG_CYZ_INTR -static irqreturn_t cyz_interrupt(int irq, void *dev_id) -{ - struct cyclades_card *cinfo = dev_id; - - if (unlikely(!cyz_is_loaded(cinfo))) { -#ifdef CY_DEBUG_INTERRUPTS - printk(KERN_DEBUG "cyz_interrupt: board not yet loaded " - "(IRQ%d).\n", irq); -#endif - return IRQ_NONE; - } - - /* Handle the interrupts */ - cyz_handle_cmd(cinfo); - - return IRQ_HANDLED; -} /* cyz_interrupt */ - -static void cyz_rx_restart(unsigned long arg) -{ - struct cyclades_port *info = (struct cyclades_port *)arg; - struct cyclades_card *card = info->card; - int retval; - __u32 channel = info->line - card->first_line; - unsigned long flags; - - spin_lock_irqsave(&card->card_lock, flags); - retval = cyz_issue_cmd(card, channel, C_CM_INTBACK2, 0L); - if (retval != 0) { - printk(KERN_ERR "cyc:cyz_rx_restart retval on ttyC%d was %x\n", - info->line, retval); - } - spin_unlock_irqrestore(&card->card_lock, flags); -} - -#else /* CONFIG_CYZ_INTR */ - -static void cyz_poll(unsigned long arg) -{ - struct cyclades_card *cinfo; - struct cyclades_port *info; - unsigned long expires = jiffies + HZ; - unsigned int port, card; - - for (card = 0; card < NR_CARDS; card++) { - cinfo = &cy_card[card]; - - if (!cy_is_Z(cinfo)) - continue; - if (!cyz_is_loaded(cinfo)) - continue; - - /* Skip first polling cycle to avoid racing conditions with the FW */ - if (!cinfo->intr_enabled) { - cinfo->intr_enabled = 1; - continue; - } - - cyz_handle_cmd(cinfo); - - for (port = 0; port < cinfo->nports; port++) { - struct tty_struct *tty; - - info = &cinfo->ports[port]; - tty = tty_port_tty_get(&info->port); - /* OK to pass NULL to the handle functions below. - They need to drop the data in that case. */ - - if (!info->throttle) - cyz_handle_rx(info, tty); - cyz_handle_tx(info, tty); - tty_kref_put(tty); - } - /* poll every 'cyz_polling_cycle' period */ - expires = jiffies + cyz_polling_cycle; - } - mod_timer(&cyz_timerlist, expires); -} /* cyz_poll */ - -#endif /* CONFIG_CYZ_INTR */ - -/********** End of block of Cyclades-Z specific code *********/ -/***********************************************************/ - -/* This is called whenever a port becomes active; - interrupts are enabled and DTR & RTS are turned on. - */ -static int cy_startup(struct cyclades_port *info, struct tty_struct *tty) -{ - struct cyclades_card *card; - unsigned long flags; - int retval = 0; - int channel; - unsigned long page; - - card = info->card; - channel = info->line - card->first_line; - - page = get_zeroed_page(GFP_KERNEL); - if (!page) - return -ENOMEM; - - spin_lock_irqsave(&card->card_lock, flags); - - if (info->port.flags & ASYNC_INITIALIZED) - goto errout; - - if (!info->type) { - set_bit(TTY_IO_ERROR, &tty->flags); - goto errout; - } - - if (info->port.xmit_buf) - free_page(page); - else - info->port.xmit_buf = (unsigned char *)page; - - spin_unlock_irqrestore(&card->card_lock, flags); - - cy_set_line_char(info, tty); - - if (!cy_is_Z(card)) { - channel &= 0x03; - - spin_lock_irqsave(&card->card_lock, flags); - - cyy_writeb(info, CyCAR, channel); - - cyy_writeb(info, CyRTPR, - (info->default_timeout ? info->default_timeout : 0x02)); - /* 10ms rx timeout */ - - cyy_issue_cmd(info, CyCHAN_CTL | CyENB_RCVR | CyENB_XMTR); - - cyy_change_rts_dtr(info, TIOCM_RTS | TIOCM_DTR, 0); - - cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyRxData); - } else { - struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl; - - if (!cyz_is_loaded(card)) - return -ENODEV; - -#ifdef CY_DEBUG_OPEN - printk(KERN_DEBUG "cyc startup Z card %d, channel %d, " - "base_addr %p\n", card, channel, card->base_addr); -#endif - spin_lock_irqsave(&card->card_lock, flags); - - cy_writel(&ch_ctrl->op_mode, C_CH_ENABLE); -#ifdef Z_WAKE -#ifdef CONFIG_CYZ_INTR - cy_writel(&ch_ctrl->intr_enable, - C_IN_TXBEMPTY | C_IN_TXLOWWM | C_IN_RXHIWM | - C_IN_RXNNDT | C_IN_IOCTLW | C_IN_MDCD); -#else - cy_writel(&ch_ctrl->intr_enable, - C_IN_IOCTLW | C_IN_MDCD); -#endif /* CONFIG_CYZ_INTR */ -#else -#ifdef CONFIG_CYZ_INTR - cy_writel(&ch_ctrl->intr_enable, - C_IN_TXBEMPTY | C_IN_TXLOWWM | C_IN_RXHIWM | - C_IN_RXNNDT | C_IN_MDCD); -#else - cy_writel(&ch_ctrl->intr_enable, C_IN_MDCD); -#endif /* CONFIG_CYZ_INTR */ -#endif /* Z_WAKE */ - - retval = cyz_issue_cmd(card, channel, C_CM_IOCTL, 0L); - if (retval != 0) { - printk(KERN_ERR "cyc:startup(1) retval on ttyC%d was " - "%x\n", info->line, retval); - } - - /* Flush RX buffers before raising DTR and RTS */ - retval = cyz_issue_cmd(card, channel, C_CM_FLUSH_RX, 0L); - if (retval != 0) { - printk(KERN_ERR "cyc:startup(2) retval on ttyC%d was " - "%x\n", info->line, retval); - } - - /* set timeout !!! */ - /* set RTS and DTR !!! */ - tty_port_raise_dtr_rts(&info->port); - - /* enable send, recv, modem !!! */ - } - - info->port.flags |= ASYNC_INITIALIZED; - - clear_bit(TTY_IO_ERROR, &tty->flags); - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - info->breakon = info->breakoff = 0; - memset((char *)&info->idle_stats, 0, sizeof(info->idle_stats)); - info->idle_stats.in_use = - info->idle_stats.recv_idle = - info->idle_stats.xmit_idle = jiffies; - - spin_unlock_irqrestore(&card->card_lock, flags); - -#ifdef CY_DEBUG_OPEN - printk(KERN_DEBUG "cyc startup done\n"); -#endif - return 0; - -errout: - spin_unlock_irqrestore(&card->card_lock, flags); - free_page(page); - return retval; -} /* startup */ - -static void start_xmit(struct cyclades_port *info) -{ - struct cyclades_card *card = info->card; - unsigned long flags; - int channel = info->line - card->first_line; - - if (!cy_is_Z(card)) { - spin_lock_irqsave(&card->card_lock, flags); - cyy_writeb(info, CyCAR, channel & 0x03); - cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyTxRdy); - spin_unlock_irqrestore(&card->card_lock, flags); - } else { -#ifdef CONFIG_CYZ_INTR - int retval; - - spin_lock_irqsave(&card->card_lock, flags); - retval = cyz_issue_cmd(card, channel, C_CM_INTBACK, 0L); - if (retval != 0) { - printk(KERN_ERR "cyc:start_xmit retval on ttyC%d was " - "%x\n", info->line, retval); - } - spin_unlock_irqrestore(&card->card_lock, flags); -#else /* CONFIG_CYZ_INTR */ - /* Don't have to do anything at this time */ -#endif /* CONFIG_CYZ_INTR */ - } -} /* start_xmit */ - -/* - * This routine shuts down a serial port; interrupts are disabled, - * and DTR is dropped if the hangup on close termio flag is on. - */ -static void cy_shutdown(struct cyclades_port *info, struct tty_struct *tty) -{ - struct cyclades_card *card; - unsigned long flags; - int channel; - - if (!(info->port.flags & ASYNC_INITIALIZED)) - return; - - card = info->card; - channel = info->line - card->first_line; - if (!cy_is_Z(card)) { - spin_lock_irqsave(&card->card_lock, flags); - - /* Clear delta_msr_wait queue to avoid mem leaks. */ - wake_up_interruptible(&info->port.delta_msr_wait); - - if (info->port.xmit_buf) { - unsigned char *temp; - temp = info->port.xmit_buf; - info->port.xmit_buf = NULL; - free_page((unsigned long)temp); - } - if (tty->termios->c_cflag & HUPCL) - cyy_change_rts_dtr(info, 0, TIOCM_RTS | TIOCM_DTR); - - cyy_issue_cmd(info, CyCHAN_CTL | CyDIS_RCVR); - /* it may be appropriate to clear _XMIT at - some later date (after testing)!!! */ - - set_bit(TTY_IO_ERROR, &tty->flags); - info->port.flags &= ~ASYNC_INITIALIZED; - spin_unlock_irqrestore(&card->card_lock, flags); - } else { -#ifdef CY_DEBUG_OPEN - printk(KERN_DEBUG "cyc shutdown Z card %d, channel %d, " - "base_addr %p\n", card, channel, card->base_addr); -#endif - - if (!cyz_is_loaded(card)) - return; - - spin_lock_irqsave(&card->card_lock, flags); - - if (info->port.xmit_buf) { - unsigned char *temp; - temp = info->port.xmit_buf; - info->port.xmit_buf = NULL; - free_page((unsigned long)temp); - } - - if (tty->termios->c_cflag & HUPCL) - tty_port_lower_dtr_rts(&info->port); - - set_bit(TTY_IO_ERROR, &tty->flags); - info->port.flags &= ~ASYNC_INITIALIZED; - - spin_unlock_irqrestore(&card->card_lock, flags); - } - -#ifdef CY_DEBUG_OPEN - printk(KERN_DEBUG "cyc shutdown done\n"); -#endif -} /* shutdown */ - -/* - * ------------------------------------------------------------ - * cy_open() and friends - * ------------------------------------------------------------ - */ - -/* - * This routine is called whenever a serial port is opened. It - * performs the serial-specific initialization for the tty structure. - */ -static int cy_open(struct tty_struct *tty, struct file *filp) -{ - struct cyclades_port *info; - unsigned int i, line; - int retval; - - line = tty->index; - if (tty->index < 0 || NR_PORTS <= line) - return -ENODEV; - - for (i = 0; i < NR_CARDS; i++) - if (line < cy_card[i].first_line + cy_card[i].nports && - line >= cy_card[i].first_line) - break; - if (i >= NR_CARDS) - return -ENODEV; - info = &cy_card[i].ports[line - cy_card[i].first_line]; - if (info->line < 0) - return -ENODEV; - - /* If the card's firmware hasn't been loaded, - treat it as absent from the system. This - will make the user pay attention. - */ - if (cy_is_Z(info->card)) { - struct cyclades_card *cinfo = info->card; - struct FIRM_ID __iomem *firm_id = cinfo->base_addr + ID_ADDRESS; - - if (!cyz_is_loaded(cinfo)) { - if (cinfo->hw_ver == ZE_V1 && cyz_fpga_loaded(cinfo) && - readl(&firm_id->signature) == - ZFIRM_HLT) { - printk(KERN_ERR "cyc:Cyclades-Z Error: you " - "need an external power supply for " - "this number of ports.\nFirmware " - "halted.\n"); - } else { - printk(KERN_ERR "cyc:Cyclades-Z firmware not " - "yet loaded\n"); - } - return -ENODEV; - } -#ifdef CONFIG_CYZ_INTR - else { - /* In case this Z board is operating in interrupt mode, its - interrupts should be enabled as soon as the first open - happens to one of its ports. */ - if (!cinfo->intr_enabled) { - u16 intr; - - /* Enable interrupts on the PLX chip */ - intr = readw(&cinfo->ctl_addr.p9060-> - intr_ctrl_stat) | 0x0900; - cy_writew(&cinfo->ctl_addr.p9060-> - intr_ctrl_stat, intr); - /* Enable interrupts on the FW */ - retval = cyz_issue_cmd(cinfo, 0, - C_CM_IRQ_ENBL, 0L); - if (retval != 0) { - printk(KERN_ERR "cyc:IRQ enable retval " - "was %x\n", retval); - } - cinfo->intr_enabled = 1; - } - } -#endif /* CONFIG_CYZ_INTR */ - /* Make sure this Z port really exists in hardware */ - if (info->line > (cinfo->first_line + cinfo->nports - 1)) - return -ENODEV; - } -#ifdef CY_DEBUG_OTHER - printk(KERN_DEBUG "cyc:cy_open ttyC%d\n", info->line); -#endif - tty->driver_data = info; - if (serial_paranoia_check(info, tty->name, "cy_open")) - return -ENODEV; - -#ifdef CY_DEBUG_OPEN - printk(KERN_DEBUG "cyc:cy_open ttyC%d, count = %d\n", info->line, - info->port.count); -#endif - info->port.count++; -#ifdef CY_DEBUG_COUNT - printk(KERN_DEBUG "cyc:cy_open (%d): incrementing count to %d\n", - current->pid, info->port.count); -#endif - - /* - * If the port is the middle of closing, bail out now - */ - if (tty_hung_up_p(filp) || (info->port.flags & ASYNC_CLOSING)) { - wait_event_interruptible_tty(info->port.close_wait, - !(info->port.flags & ASYNC_CLOSING)); - return (info->port.flags & ASYNC_HUP_NOTIFY) ? -EAGAIN: -ERESTARTSYS; - } - - /* - * Start up serial port - */ - retval = cy_startup(info, tty); - if (retval) - return retval; - - retval = tty_port_block_til_ready(&info->port, tty, filp); - if (retval) { -#ifdef CY_DEBUG_OPEN - printk(KERN_DEBUG "cyc:cy_open returning after block_til_ready " - "with %d\n", retval); -#endif - return retval; - } - - info->throttle = 0; - tty_port_tty_set(&info->port, tty); - -#ifdef CY_DEBUG_OPEN - printk(KERN_DEBUG "cyc:cy_open done\n"); -#endif - return 0; -} /* cy_open */ - -/* - * cy_wait_until_sent() --- wait until the transmitter is empty - */ -static void cy_wait_until_sent(struct tty_struct *tty, int timeout) -{ - struct cyclades_card *card; - struct cyclades_port *info = tty->driver_data; - unsigned long orig_jiffies; - int char_time; - - if (serial_paranoia_check(info, tty->name, "cy_wait_until_sent")) - return; - - if (info->xmit_fifo_size == 0) - return; /* Just in case.... */ - - orig_jiffies = jiffies; - /* - * Set the check interval to be 1/5 of the estimated time to - * send a single character, and make it at least 1. The check - * interval should also be less than the timeout. - * - * Note: we have to use pretty tight timings here to satisfy - * the NIST-PCTS. - */ - char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size; - char_time = char_time / 5; - if (char_time <= 0) - char_time = 1; - if (timeout < 0) - timeout = 0; - if (timeout) - char_time = min(char_time, timeout); - /* - * If the transmitter hasn't cleared in twice the approximate - * amount of time to send the entire FIFO, it probably won't - * ever clear. This assumes the UART isn't doing flow - * control, which is currently the case. Hence, if it ever - * takes longer than info->timeout, this is probably due to a - * UART bug of some kind. So, we clamp the timeout parameter at - * 2*info->timeout. - */ - if (!timeout || timeout > 2 * info->timeout) - timeout = 2 * info->timeout; -#ifdef CY_DEBUG_WAIT_UNTIL_SENT - printk(KERN_DEBUG "In cy_wait_until_sent(%d) check=%d, jiff=%lu...", - timeout, char_time, jiffies); -#endif - card = info->card; - if (!cy_is_Z(card)) { - while (cyy_readb(info, CySRER) & CyTxRdy) { -#ifdef CY_DEBUG_WAIT_UNTIL_SENT - printk(KERN_DEBUG "Not clean (jiff=%lu)...", jiffies); -#endif - if (msleep_interruptible(jiffies_to_msecs(char_time))) - break; - if (timeout && time_after(jiffies, orig_jiffies + - timeout)) - break; - } - } - /* Run one more char cycle */ - msleep_interruptible(jiffies_to_msecs(char_time * 5)); -#ifdef CY_DEBUG_WAIT_UNTIL_SENT - printk(KERN_DEBUG "Clean (jiff=%lu)...done\n", jiffies); -#endif -} - -static void cy_flush_buffer(struct tty_struct *tty) -{ - struct cyclades_port *info = tty->driver_data; - struct cyclades_card *card; - int channel, retval; - unsigned long flags; - -#ifdef CY_DEBUG_IO - printk(KERN_DEBUG "cyc:cy_flush_buffer ttyC%d\n", info->line); -#endif - - if (serial_paranoia_check(info, tty->name, "cy_flush_buffer")) - return; - - card = info->card; - channel = info->line - card->first_line; - - spin_lock_irqsave(&card->card_lock, flags); - info->xmit_cnt = info->xmit_head = info->xmit_tail = 0; - spin_unlock_irqrestore(&card->card_lock, flags); - - if (cy_is_Z(card)) { /* If it is a Z card, flush the on-board - buffers as well */ - spin_lock_irqsave(&card->card_lock, flags); - retval = cyz_issue_cmd(card, channel, C_CM_FLUSH_TX, 0L); - if (retval != 0) { - printk(KERN_ERR "cyc: flush_buffer retval on ttyC%d " - "was %x\n", info->line, retval); - } - spin_unlock_irqrestore(&card->card_lock, flags); - } - tty_wakeup(tty); -} /* cy_flush_buffer */ - - -static void cy_do_close(struct tty_port *port) -{ - struct cyclades_port *info = container_of(port, struct cyclades_port, - port); - struct cyclades_card *card; - unsigned long flags; - int channel; - - card = info->card; - channel = info->line - card->first_line; - spin_lock_irqsave(&card->card_lock, flags); - - if (!cy_is_Z(card)) { - /* Stop accepting input */ - cyy_writeb(info, CyCAR, channel & 0x03); - cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyRxData); - if (info->port.flags & ASYNC_INITIALIZED) { - /* Waiting for on-board buffers to be empty before - closing the port */ - spin_unlock_irqrestore(&card->card_lock, flags); - cy_wait_until_sent(port->tty, info->timeout); - spin_lock_irqsave(&card->card_lock, flags); - } - } else { -#ifdef Z_WAKE - /* Waiting for on-board buffers to be empty before closing - the port */ - struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl; - int retval; - - if (readl(&ch_ctrl->flow_status) != C_FS_TXIDLE) { - retval = cyz_issue_cmd(card, channel, C_CM_IOCTLW, 0L); - if (retval != 0) { - printk(KERN_DEBUG "cyc:cy_close retval on " - "ttyC%d was %x\n", info->line, retval); - } - spin_unlock_irqrestore(&card->card_lock, flags); - wait_for_completion_interruptible(&info->shutdown_wait); - spin_lock_irqsave(&card->card_lock, flags); - } -#endif - } - spin_unlock_irqrestore(&card->card_lock, flags); - cy_shutdown(info, port->tty); -} - -/* - * This routine is called when a particular tty device is closed. - */ -static void cy_close(struct tty_struct *tty, struct file *filp) -{ - struct cyclades_port *info = tty->driver_data; - if (!info || serial_paranoia_check(info, tty->name, "cy_close")) - return; - tty_port_close(&info->port, tty, filp); -} /* cy_close */ - -/* This routine gets called when tty_write has put something into - * the write_queue. The characters may come from user space or - * kernel space. - * - * This routine will return the number of characters actually - * accepted for writing. - * - * If the port is not already transmitting stuff, start it off by - * enabling interrupts. The interrupt service routine will then - * ensure that the characters are sent. - * If the port is already active, there is no need to kick it. - * - */ -static int cy_write(struct tty_struct *tty, const unsigned char *buf, int count) -{ - struct cyclades_port *info = tty->driver_data; - unsigned long flags; - int c, ret = 0; - -#ifdef CY_DEBUG_IO - printk(KERN_DEBUG "cyc:cy_write ttyC%d\n", info->line); -#endif - - if (serial_paranoia_check(info, tty->name, "cy_write")) - return 0; - - if (!info->port.xmit_buf) - return 0; - - spin_lock_irqsave(&info->card->card_lock, flags); - while (1) { - c = min(count, (int)(SERIAL_XMIT_SIZE - info->xmit_cnt - 1)); - c = min(c, (int)(SERIAL_XMIT_SIZE - info->xmit_head)); - - if (c <= 0) - break; - - memcpy(info->port.xmit_buf + info->xmit_head, buf, c); - info->xmit_head = (info->xmit_head + c) & - (SERIAL_XMIT_SIZE - 1); - info->xmit_cnt += c; - buf += c; - count -= c; - ret += c; - } - spin_unlock_irqrestore(&info->card->card_lock, flags); - - info->idle_stats.xmit_bytes += ret; - info->idle_stats.xmit_idle = jiffies; - - if (info->xmit_cnt && !tty->stopped && !tty->hw_stopped) - start_xmit(info); - - return ret; -} /* cy_write */ - -/* - * This routine is called by the kernel to write a single - * character to the tty device. If the kernel uses this routine, - * it must call the flush_chars() routine (if defined) when it is - * done stuffing characters into the driver. If there is no room - * in the queue, the character is ignored. - */ -static int cy_put_char(struct tty_struct *tty, unsigned char ch) -{ - struct cyclades_port *info = tty->driver_data; - unsigned long flags; - -#ifdef CY_DEBUG_IO - printk(KERN_DEBUG "cyc:cy_put_char ttyC%d\n", info->line); -#endif - - if (serial_paranoia_check(info, tty->name, "cy_put_char")) - return 0; - - if (!info->port.xmit_buf) - return 0; - - spin_lock_irqsave(&info->card->card_lock, flags); - if (info->xmit_cnt >= (int)(SERIAL_XMIT_SIZE - 1)) { - spin_unlock_irqrestore(&info->card->card_lock, flags); - return 0; - } - - info->port.xmit_buf[info->xmit_head++] = ch; - info->xmit_head &= SERIAL_XMIT_SIZE - 1; - info->xmit_cnt++; - info->idle_stats.xmit_bytes++; - info->idle_stats.xmit_idle = jiffies; - spin_unlock_irqrestore(&info->card->card_lock, flags); - return 1; -} /* cy_put_char */ - -/* - * This routine is called by the kernel after it has written a - * series of characters to the tty device using put_char(). - */ -static void cy_flush_chars(struct tty_struct *tty) -{ - struct cyclades_port *info = tty->driver_data; - -#ifdef CY_DEBUG_IO - printk(KERN_DEBUG "cyc:cy_flush_chars ttyC%d\n", info->line); -#endif - - if (serial_paranoia_check(info, tty->name, "cy_flush_chars")) - return; - - if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped || - !info->port.xmit_buf) - return; - - start_xmit(info); -} /* cy_flush_chars */ - -/* - * This routine returns the numbers of characters the tty driver - * will accept for queuing to be written. This number is subject - * to change as output buffers get emptied, or if the output flow - * control is activated. - */ -static int cy_write_room(struct tty_struct *tty) -{ - struct cyclades_port *info = tty->driver_data; - int ret; - -#ifdef CY_DEBUG_IO - printk(KERN_DEBUG "cyc:cy_write_room ttyC%d\n", info->line); -#endif - - if (serial_paranoia_check(info, tty->name, "cy_write_room")) - return 0; - ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1; - if (ret < 0) - ret = 0; - return ret; -} /* cy_write_room */ - -static int cy_chars_in_buffer(struct tty_struct *tty) -{ - struct cyclades_port *info = tty->driver_data; - - if (serial_paranoia_check(info, tty->name, "cy_chars_in_buffer")) - return 0; - -#ifdef Z_EXT_CHARS_IN_BUFFER - if (!cy_is_Z(info->card)) { -#endif /* Z_EXT_CHARS_IN_BUFFER */ -#ifdef CY_DEBUG_IO - printk(KERN_DEBUG "cyc:cy_chars_in_buffer ttyC%d %d\n", - info->line, info->xmit_cnt); -#endif - return info->xmit_cnt; -#ifdef Z_EXT_CHARS_IN_BUFFER - } else { - struct BUF_CTRL __iomem *buf_ctrl = info->u.cyz.buf_ctrl; - int char_count; - __u32 tx_put, tx_get, tx_bufsize; - - tx_get = readl(&buf_ctrl->tx_get); - tx_put = readl(&buf_ctrl->tx_put); - tx_bufsize = readl(&buf_ctrl->tx_bufsize); - if (tx_put >= tx_get) - char_count = tx_put - tx_get; - else - char_count = tx_put - tx_get + tx_bufsize; -#ifdef CY_DEBUG_IO - printk(KERN_DEBUG "cyc:cy_chars_in_buffer ttyC%d %d\n", - info->line, info->xmit_cnt + char_count); -#endif - return info->xmit_cnt + char_count; - } -#endif /* Z_EXT_CHARS_IN_BUFFER */ -} /* cy_chars_in_buffer */ - -/* - * ------------------------------------------------------------ - * cy_ioctl() and friends - * ------------------------------------------------------------ - */ - -static void cyy_baud_calc(struct cyclades_port *info, __u32 baud) -{ - int co, co_val, bpr; - __u32 cy_clock = ((info->chip_rev >= CD1400_REV_J) ? 60000000 : - 25000000); - - if (baud == 0) { - info->tbpr = info->tco = info->rbpr = info->rco = 0; - return; - } - - /* determine which prescaler to use */ - for (co = 4, co_val = 2048; co; co--, co_val >>= 2) { - if (cy_clock / co_val / baud > 63) - break; - } - - bpr = (cy_clock / co_val * 2 / baud + 1) / 2; - if (bpr > 255) - bpr = 255; - - info->tbpr = info->rbpr = bpr; - info->tco = info->rco = co; -} - -/* - * This routine finds or computes the various line characteristics. - * It used to be called config_setup - */ -static void cy_set_line_char(struct cyclades_port *info, struct tty_struct *tty) -{ - struct cyclades_card *card; - unsigned long flags; - int channel; - unsigned cflag, iflag; - int baud, baud_rate = 0; - int i; - - if (!tty->termios) /* XXX can this happen at all? */ - return; - - if (info->line == -1) - return; - - cflag = tty->termios->c_cflag; - iflag = tty->termios->c_iflag; - - /* - * Set up the tty->alt_speed kludge - */ - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) - tty->alt_speed = 57600; - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) - tty->alt_speed = 115200; - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) - tty->alt_speed = 230400; - if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) - tty->alt_speed = 460800; - - card = info->card; - channel = info->line - card->first_line; - - if (!cy_is_Z(card)) { - u32 cflags; - - /* baud rate */ - baud = tty_get_baud_rate(tty); - if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) == - ASYNC_SPD_CUST) { - if (info->custom_divisor) - baud_rate = info->baud / info->custom_divisor; - else - baud_rate = info->baud; - } else if (baud > CD1400_MAX_SPEED) { - baud = CD1400_MAX_SPEED; - } - /* find the baud index */ - for (i = 0; i < 20; i++) { - if (baud == baud_table[i]) - break; - } - if (i == 20) - i = 19; /* CD1400_MAX_SPEED */ - - if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) == - ASYNC_SPD_CUST) { - cyy_baud_calc(info, baud_rate); - } else { - if (info->chip_rev >= CD1400_REV_J) { - /* It is a CD1400 rev. J or later */ - info->tbpr = baud_bpr_60[i]; /* Tx BPR */ - info->tco = baud_co_60[i]; /* Tx CO */ - info->rbpr = baud_bpr_60[i]; /* Rx BPR */ - info->rco = baud_co_60[i]; /* Rx CO */ - } else { - info->tbpr = baud_bpr_25[i]; /* Tx BPR */ - info->tco = baud_co_25[i]; /* Tx CO */ - info->rbpr = baud_bpr_25[i]; /* Rx BPR */ - info->rco = baud_co_25[i]; /* Rx CO */ - } - } - if (baud_table[i] == 134) { - /* get it right for 134.5 baud */ - info->timeout = (info->xmit_fifo_size * HZ * 30 / 269) + - 2; - } else if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) == - ASYNC_SPD_CUST) { - info->timeout = (info->xmit_fifo_size * HZ * 15 / - baud_rate) + 2; - } else if (baud_table[i]) { - info->timeout = (info->xmit_fifo_size * HZ * 15 / - baud_table[i]) + 2; - /* this needs to be propagated into the card info */ - } else { - info->timeout = 0; - } - /* By tradition (is it a standard?) a baud rate of zero - implies the line should be/has been closed. A bit - later in this routine such a test is performed. */ - - /* byte size and parity */ - info->cor5 = 0; - info->cor4 = 0; - /* receive threshold */ - info->cor3 = (info->default_threshold ? - info->default_threshold : baud_cor3[i]); - info->cor2 = CyETC; - switch (cflag & CSIZE) { - case CS5: - info->cor1 = Cy_5_BITS; - break; - case CS6: - info->cor1 = Cy_6_BITS; - break; - case CS7: - info->cor1 = Cy_7_BITS; - break; - case CS8: - info->cor1 = Cy_8_BITS; - break; - } - if (cflag & CSTOPB) - info->cor1 |= Cy_2_STOP; - - if (cflag & PARENB) { - if (cflag & PARODD) - info->cor1 |= CyPARITY_O; - else - info->cor1 |= CyPARITY_E; - } else - info->cor1 |= CyPARITY_NONE; - - /* CTS flow control flag */ - if (cflag & CRTSCTS) { - info->port.flags |= ASYNC_CTS_FLOW; - info->cor2 |= CyCtsAE; - } else { - info->port.flags &= ~ASYNC_CTS_FLOW; - info->cor2 &= ~CyCtsAE; - } - if (cflag & CLOCAL) - info->port.flags &= ~ASYNC_CHECK_CD; - else - info->port.flags |= ASYNC_CHECK_CD; - - /*********************************************** - The hardware option, CyRtsAO, presents RTS when - the chip has characters to send. Since most modems - use RTS as reverse (inbound) flow control, this - option is not used. If inbound flow control is - necessary, DTR can be programmed to provide the - appropriate signals for use with a non-standard - cable. Contact Marcio Saito for details. - ***********************************************/ - - channel &= 0x03; - - spin_lock_irqsave(&card->card_lock, flags); - cyy_writeb(info, CyCAR, channel); - - /* tx and rx baud rate */ - - cyy_writeb(info, CyTCOR, info->tco); - cyy_writeb(info, CyTBPR, info->tbpr); - cyy_writeb(info, CyRCOR, info->rco); - cyy_writeb(info, CyRBPR, info->rbpr); - - /* set line characteristics according configuration */ - - cyy_writeb(info, CySCHR1, START_CHAR(tty)); - cyy_writeb(info, CySCHR2, STOP_CHAR(tty)); - cyy_writeb(info, CyCOR1, info->cor1); - cyy_writeb(info, CyCOR2, info->cor2); - cyy_writeb(info, CyCOR3, info->cor3); - cyy_writeb(info, CyCOR4, info->cor4); - cyy_writeb(info, CyCOR5, info->cor5); - - cyy_issue_cmd(info, CyCOR_CHANGE | CyCOR1ch | CyCOR2ch | - CyCOR3ch); - - /* !!! Is this needed? */ - cyy_writeb(info, CyCAR, channel); - cyy_writeb(info, CyRTPR, - (info->default_timeout ? info->default_timeout : 0x02)); - /* 10ms rx timeout */ - - cflags = CyCTS; - if (!C_CLOCAL(tty)) - cflags |= CyDSR | CyRI | CyDCD; - /* without modem intr */ - cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyMdmCh); - /* act on 1->0 modem transitions */ - if ((cflag & CRTSCTS) && info->rflow) - cyy_writeb(info, CyMCOR1, cflags | rflow_thr[i]); - else - cyy_writeb(info, CyMCOR1, cflags); - /* act on 0->1 modem transitions */ - cyy_writeb(info, CyMCOR2, cflags); - - if (i == 0) /* baud rate is zero, turn off line */ - cyy_change_rts_dtr(info, 0, TIOCM_DTR); - else - cyy_change_rts_dtr(info, TIOCM_DTR, 0); - - clear_bit(TTY_IO_ERROR, &tty->flags); - spin_unlock_irqrestore(&card->card_lock, flags); - - } else { - struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl; - __u32 sw_flow; - int retval; - - if (!cyz_is_loaded(card)) - return; - - /* baud rate */ - baud = tty_get_baud_rate(tty); - if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) == - ASYNC_SPD_CUST) { - if (info->custom_divisor) - baud_rate = info->baud / info->custom_divisor; - else - baud_rate = info->baud; - } else if (baud > CYZ_MAX_SPEED) { - baud = CYZ_MAX_SPEED; - } - cy_writel(&ch_ctrl->comm_baud, baud); - - if (baud == 134) { - /* get it right for 134.5 baud */ - info->timeout = (info->xmit_fifo_size * HZ * 30 / 269) + - 2; - } else if (baud == 38400 && (info->port.flags & ASYNC_SPD_MASK) == - ASYNC_SPD_CUST) { - info->timeout = (info->xmit_fifo_size * HZ * 15 / - baud_rate) + 2; - } else if (baud) { - info->timeout = (info->xmit_fifo_size * HZ * 15 / - baud) + 2; - /* this needs to be propagated into the card info */ - } else { - info->timeout = 0; - } - - /* byte size and parity */ - switch (cflag & CSIZE) { - case CS5: - cy_writel(&ch_ctrl->comm_data_l, C_DL_CS5); - break; - case CS6: - cy_writel(&ch_ctrl->comm_data_l, C_DL_CS6); - break; - case CS7: - cy_writel(&ch_ctrl->comm_data_l, C_DL_CS7); - break; - case CS8: - cy_writel(&ch_ctrl->comm_data_l, C_DL_CS8); - break; - } - if (cflag & CSTOPB) { - cy_writel(&ch_ctrl->comm_data_l, - readl(&ch_ctrl->comm_data_l) | C_DL_2STOP); - } else { - cy_writel(&ch_ctrl->comm_data_l, - readl(&ch_ctrl->comm_data_l) | C_DL_1STOP); - } - if (cflag & PARENB) { - if (cflag & PARODD) - cy_writel(&ch_ctrl->comm_parity, C_PR_ODD); - else - cy_writel(&ch_ctrl->comm_parity, C_PR_EVEN); - } else - cy_writel(&ch_ctrl->comm_parity, C_PR_NONE); - - /* CTS flow control flag */ - if (cflag & CRTSCTS) { - cy_writel(&ch_ctrl->hw_flow, - readl(&ch_ctrl->hw_flow) | C_RS_CTS | C_RS_RTS); - } else { - cy_writel(&ch_ctrl->hw_flow, readl(&ch_ctrl->hw_flow) & - ~(C_RS_CTS | C_RS_RTS)); - } - /* As the HW flow control is done in firmware, the driver - doesn't need to care about it */ - info->port.flags &= ~ASYNC_CTS_FLOW; - - /* XON/XOFF/XANY flow control flags */ - sw_flow = 0; - if (iflag & IXON) { - sw_flow |= C_FL_OXX; - if (iflag & IXANY) - sw_flow |= C_FL_OIXANY; - } - cy_writel(&ch_ctrl->sw_flow, sw_flow); - - retval = cyz_issue_cmd(card, channel, C_CM_IOCTL, 0L); - if (retval != 0) { - printk(KERN_ERR "cyc:set_line_char retval on ttyC%d " - "was %x\n", info->line, retval); - } - - /* CD sensitivity */ - if (cflag & CLOCAL) - info->port.flags &= ~ASYNC_CHECK_CD; - else - info->port.flags |= ASYNC_CHECK_CD; - - if (baud == 0) { /* baud rate is zero, turn off line */ - cy_writel(&ch_ctrl->rs_control, - readl(&ch_ctrl->rs_control) & ~C_RS_DTR); -#ifdef CY_DEBUG_DTR - printk(KERN_DEBUG "cyc:set_line_char dropping Z DTR\n"); -#endif - } else { - cy_writel(&ch_ctrl->rs_control, - readl(&ch_ctrl->rs_control) | C_RS_DTR); -#ifdef CY_DEBUG_DTR - printk(KERN_DEBUG "cyc:set_line_char raising Z DTR\n"); -#endif - } - - retval = cyz_issue_cmd(card, channel, C_CM_IOCTLM, 0L); - if (retval != 0) { - printk(KERN_ERR "cyc:set_line_char(2) retval on ttyC%d " - "was %x\n", info->line, retval); - } - - clear_bit(TTY_IO_ERROR, &tty->flags); - } -} /* set_line_char */ - -static int cy_get_serial_info(struct cyclades_port *info, - struct serial_struct __user *retinfo) -{ - struct cyclades_card *cinfo = info->card; - struct serial_struct tmp = { - .type = info->type, - .line = info->line, - .port = (info->card - cy_card) * 0x100 + info->line - - cinfo->first_line, - .irq = cinfo->irq, - .flags = info->port.flags, - .close_delay = info->port.close_delay, - .closing_wait = info->port.closing_wait, - .baud_base = info->baud, - .custom_divisor = info->custom_divisor, - .hub6 = 0, /*!!! */ - }; - return copy_to_user(retinfo, &tmp, sizeof(*retinfo)) ? -EFAULT : 0; -} - -static int -cy_set_serial_info(struct cyclades_port *info, struct tty_struct *tty, - struct serial_struct __user *new_info) -{ - struct serial_struct new_serial; - int ret; - - if (copy_from_user(&new_serial, new_info, sizeof(new_serial))) - return -EFAULT; - - mutex_lock(&info->port.mutex); - if (!capable(CAP_SYS_ADMIN)) { - if (new_serial.close_delay != info->port.close_delay || - new_serial.baud_base != info->baud || - (new_serial.flags & ASYNC_FLAGS & - ~ASYNC_USR_MASK) != - (info->port.flags & ASYNC_FLAGS & ~ASYNC_USR_MASK)) - { - mutex_unlock(&info->port.mutex); - return -EPERM; - } - info->port.flags = (info->port.flags & ~ASYNC_USR_MASK) | - (new_serial.flags & ASYNC_USR_MASK); - info->baud = new_serial.baud_base; - info->custom_divisor = new_serial.custom_divisor; - goto check_and_exit; - } - - /* - * OK, past this point, all the error checking has been done. - * At this point, we start making changes..... - */ - - info->baud = new_serial.baud_base; - info->custom_divisor = new_serial.custom_divisor; - info->port.flags = (info->port.flags & ~ASYNC_FLAGS) | - (new_serial.flags & ASYNC_FLAGS); - info->port.close_delay = new_serial.close_delay * HZ / 100; - info->port.closing_wait = new_serial.closing_wait * HZ / 100; - -check_and_exit: - if (info->port.flags & ASYNC_INITIALIZED) { - cy_set_line_char(info, tty); - ret = 0; - } else { - ret = cy_startup(info, tty); - } - mutex_unlock(&info->port.mutex); - return ret; -} /* set_serial_info */ - -/* - * get_lsr_info - get line status register info - * - * Purpose: Let user call ioctl() to get info when the UART physically - * is emptied. On bus types like RS485, the transmitter must - * release the bus after transmitting. This must be done when - * the transmit shift register is empty, not be done when the - * transmit holding register is empty. This functionality - * allows an RS485 driver to be written in user space. - */ -static int get_lsr_info(struct cyclades_port *info, unsigned int __user *value) -{ - struct cyclades_card *card = info->card; - unsigned int result; - unsigned long flags; - u8 status; - - if (!cy_is_Z(card)) { - spin_lock_irqsave(&card->card_lock, flags); - status = cyy_readb(info, CySRER) & (CyTxRdy | CyTxMpty); - spin_unlock_irqrestore(&card->card_lock, flags); - result = (status ? 0 : TIOCSER_TEMT); - } else { - /* Not supported yet */ - return -EINVAL; - } - return put_user(result, (unsigned long __user *)value); -} - -static int cy_tiocmget(struct tty_struct *tty) -{ - struct cyclades_port *info = tty->driver_data; - struct cyclades_card *card; - int result; - - if (serial_paranoia_check(info, tty->name, __func__)) - return -ENODEV; - - card = info->card; - - if (!cy_is_Z(card)) { - unsigned long flags; - int channel = info->line - card->first_line; - u8 status; - - spin_lock_irqsave(&card->card_lock, flags); - cyy_writeb(info, CyCAR, channel & 0x03); - status = cyy_readb(info, CyMSVR1); - status |= cyy_readb(info, CyMSVR2); - spin_unlock_irqrestore(&card->card_lock, flags); - - if (info->rtsdtr_inv) { - result = ((status & CyRTS) ? TIOCM_DTR : 0) | - ((status & CyDTR) ? TIOCM_RTS : 0); - } else { - result = ((status & CyRTS) ? TIOCM_RTS : 0) | - ((status & CyDTR) ? TIOCM_DTR : 0); - } - result |= ((status & CyDCD) ? TIOCM_CAR : 0) | - ((status & CyRI) ? TIOCM_RNG : 0) | - ((status & CyDSR) ? TIOCM_DSR : 0) | - ((status & CyCTS) ? TIOCM_CTS : 0); - } else { - u32 lstatus; - - if (!cyz_is_loaded(card)) { - result = -ENODEV; - goto end; - } - - lstatus = readl(&info->u.cyz.ch_ctrl->rs_status); - result = ((lstatus & C_RS_RTS) ? TIOCM_RTS : 0) | - ((lstatus & C_RS_DTR) ? TIOCM_DTR : 0) | - ((lstatus & C_RS_DCD) ? TIOCM_CAR : 0) | - ((lstatus & C_RS_RI) ? TIOCM_RNG : 0) | - ((lstatus & C_RS_DSR) ? TIOCM_DSR : 0) | - ((lstatus & C_RS_CTS) ? TIOCM_CTS : 0); - } -end: - return result; -} /* cy_tiomget */ - -static int -cy_tiocmset(struct tty_struct *tty, - unsigned int set, unsigned int clear) -{ - struct cyclades_port *info = tty->driver_data; - struct cyclades_card *card; - unsigned long flags; - - if (serial_paranoia_check(info, tty->name, __func__)) - return -ENODEV; - - card = info->card; - if (!cy_is_Z(card)) { - spin_lock_irqsave(&card->card_lock, flags); - cyy_change_rts_dtr(info, set, clear); - spin_unlock_irqrestore(&card->card_lock, flags); - } else { - struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl; - int retval, channel = info->line - card->first_line; - u32 rs; - - if (!cyz_is_loaded(card)) - return -ENODEV; - - spin_lock_irqsave(&card->card_lock, flags); - rs = readl(&ch_ctrl->rs_control); - if (set & TIOCM_RTS) - rs |= C_RS_RTS; - if (clear & TIOCM_RTS) - rs &= ~C_RS_RTS; - if (set & TIOCM_DTR) { - rs |= C_RS_DTR; -#ifdef CY_DEBUG_DTR - printk(KERN_DEBUG "cyc:set_modem_info raising Z DTR\n"); -#endif - } - if (clear & TIOCM_DTR) { - rs &= ~C_RS_DTR; -#ifdef CY_DEBUG_DTR - printk(KERN_DEBUG "cyc:set_modem_info clearing " - "Z DTR\n"); -#endif - } - cy_writel(&ch_ctrl->rs_control, rs); - retval = cyz_issue_cmd(card, channel, C_CM_IOCTLM, 0L); - spin_unlock_irqrestore(&card->card_lock, flags); - if (retval != 0) { - printk(KERN_ERR "cyc:set_modem_info retval on ttyC%d " - "was %x\n", info->line, retval); - } - } - return 0; -} - -/* - * cy_break() --- routine which turns the break handling on or off - */ -static int cy_break(struct tty_struct *tty, int break_state) -{ - struct cyclades_port *info = tty->driver_data; - struct cyclades_card *card; - unsigned long flags; - int retval = 0; - - if (serial_paranoia_check(info, tty->name, "cy_break")) - return -EINVAL; - - card = info->card; - - spin_lock_irqsave(&card->card_lock, flags); - if (!cy_is_Z(card)) { - /* Let the transmit ISR take care of this (since it - requires stuffing characters into the output stream). - */ - if (break_state == -1) { - if (!info->breakon) { - info->breakon = 1; - if (!info->xmit_cnt) { - spin_unlock_irqrestore(&card->card_lock, flags); - start_xmit(info); - spin_lock_irqsave(&card->card_lock, flags); - } - } - } else { - if (!info->breakoff) { - info->breakoff = 1; - if (!info->xmit_cnt) { - spin_unlock_irqrestore(&card->card_lock, flags); - start_xmit(info); - spin_lock_irqsave(&card->card_lock, flags); - } - } - } - } else { - if (break_state == -1) { - retval = cyz_issue_cmd(card, - info->line - card->first_line, - C_CM_SET_BREAK, 0L); - if (retval != 0) { - printk(KERN_ERR "cyc:cy_break (set) retval on " - "ttyC%d was %x\n", info->line, retval); - } - } else { - retval = cyz_issue_cmd(card, - info->line - card->first_line, - C_CM_CLR_BREAK, 0L); - if (retval != 0) { - printk(KERN_DEBUG "cyc:cy_break (clr) retval " - "on ttyC%d was %x\n", info->line, - retval); - } - } - } - spin_unlock_irqrestore(&card->card_lock, flags); - return retval; -} /* cy_break */ - -static int set_threshold(struct cyclades_port *info, unsigned long value) -{ - struct cyclades_card *card = info->card; - unsigned long flags; - - if (!cy_is_Z(card)) { - info->cor3 &= ~CyREC_FIFO; - info->cor3 |= value & CyREC_FIFO; - - spin_lock_irqsave(&card->card_lock, flags); - cyy_writeb(info, CyCOR3, info->cor3); - cyy_issue_cmd(info, CyCOR_CHANGE | CyCOR3ch); - spin_unlock_irqrestore(&card->card_lock, flags); - } - return 0; -} /* set_threshold */ - -static int get_threshold(struct cyclades_port *info, - unsigned long __user *value) -{ - struct cyclades_card *card = info->card; - - if (!cy_is_Z(card)) { - u8 tmp = cyy_readb(info, CyCOR3) & CyREC_FIFO; - return put_user(tmp, value); - } - return 0; -} /* get_threshold */ - -static int set_timeout(struct cyclades_port *info, unsigned long value) -{ - struct cyclades_card *card = info->card; - unsigned long flags; - - if (!cy_is_Z(card)) { - spin_lock_irqsave(&card->card_lock, flags); - cyy_writeb(info, CyRTPR, value & 0xff); - spin_unlock_irqrestore(&card->card_lock, flags); - } - return 0; -} /* set_timeout */ - -static int get_timeout(struct cyclades_port *info, - unsigned long __user *value) -{ - struct cyclades_card *card = info->card; - - if (!cy_is_Z(card)) { - u8 tmp = cyy_readb(info, CyRTPR); - return put_user(tmp, value); - } - return 0; -} /* get_timeout */ - -static int cy_cflags_changed(struct cyclades_port *info, unsigned long arg, - struct cyclades_icount *cprev) -{ - struct cyclades_icount cnow; - unsigned long flags; - int ret; - - spin_lock_irqsave(&info->card->card_lock, flags); - cnow = info->icount; /* atomic copy */ - spin_unlock_irqrestore(&info->card->card_lock, flags); - - ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) || - ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) || - ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) || - ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts)); - - *cprev = cnow; - - return ret; -} - -/* - * This routine allows the tty driver to implement device- - * specific ioctl's. If the ioctl number passed in cmd is - * not recognized by the driver, it should return ENOIOCTLCMD. - */ -static int -cy_ioctl(struct tty_struct *tty, - unsigned int cmd, unsigned long arg) -{ - struct cyclades_port *info = tty->driver_data; - struct cyclades_icount cnow; /* kernel counter temps */ - int ret_val = 0; - unsigned long flags; - void __user *argp = (void __user *)arg; - - if (serial_paranoia_check(info, tty->name, "cy_ioctl")) - return -ENODEV; - -#ifdef CY_DEBUG_OTHER - printk(KERN_DEBUG "cyc:cy_ioctl ttyC%d, cmd = %x arg = %lx\n", - info->line, cmd, arg); -#endif - - switch (cmd) { - case CYGETMON: - if (copy_to_user(argp, &info->mon, sizeof(info->mon))) { - ret_val = -EFAULT; - break; - } - memset(&info->mon, 0, sizeof(info->mon)); - break; - case CYGETTHRESH: - ret_val = get_threshold(info, argp); - break; - case CYSETTHRESH: - ret_val = set_threshold(info, arg); - break; - case CYGETDEFTHRESH: - ret_val = put_user(info->default_threshold, - (unsigned long __user *)argp); - break; - case CYSETDEFTHRESH: - info->default_threshold = arg & 0x0f; - break; - case CYGETTIMEOUT: - ret_val = get_timeout(info, argp); - break; - case CYSETTIMEOUT: - ret_val = set_timeout(info, arg); - break; - case CYGETDEFTIMEOUT: - ret_val = put_user(info->default_timeout, - (unsigned long __user *)argp); - break; - case CYSETDEFTIMEOUT: - info->default_timeout = arg & 0xff; - break; - case CYSETRFLOW: - info->rflow = (int)arg; - break; - case CYGETRFLOW: - ret_val = info->rflow; - break; - case CYSETRTSDTR_INV: - info->rtsdtr_inv = (int)arg; - break; - case CYGETRTSDTR_INV: - ret_val = info->rtsdtr_inv; - break; - case CYGETCD1400VER: - ret_val = info->chip_rev; - break; -#ifndef CONFIG_CYZ_INTR - case CYZSETPOLLCYCLE: - cyz_polling_cycle = (arg * HZ) / 1000; - break; - case CYZGETPOLLCYCLE: - ret_val = (cyz_polling_cycle * 1000) / HZ; - break; -#endif /* CONFIG_CYZ_INTR */ - case CYSETWAIT: - info->port.closing_wait = (unsigned short)arg * HZ / 100; - break; - case CYGETWAIT: - ret_val = info->port.closing_wait / (HZ / 100); - break; - case TIOCGSERIAL: - ret_val = cy_get_serial_info(info, argp); - break; - case TIOCSSERIAL: - ret_val = cy_set_serial_info(info, tty, argp); - break; - case TIOCSERGETLSR: /* Get line status register */ - ret_val = get_lsr_info(info, argp); - break; - /* - * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change - * - mask passed in arg for lines of interest - * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking) - * Caller should use TIOCGICOUNT to see which one it was - */ - case TIOCMIWAIT: - spin_lock_irqsave(&info->card->card_lock, flags); - /* note the counters on entry */ - cnow = info->icount; - spin_unlock_irqrestore(&info->card->card_lock, flags); - ret_val = wait_event_interruptible(info->port.delta_msr_wait, - cy_cflags_changed(info, arg, &cnow)); - break; - - /* - * Get counter of input serial line interrupts (DCD,RI,DSR,CTS) - * Return: write counters to the user passed counter struct - * NB: both 1->0 and 0->1 transitions are counted except for - * RI where only 0->1 is counted. - */ - default: - ret_val = -ENOIOCTLCMD; - } - -#ifdef CY_DEBUG_OTHER - printk(KERN_DEBUG "cyc:cy_ioctl done\n"); -#endif - return ret_val; -} /* cy_ioctl */ - -static int cy_get_icount(struct tty_struct *tty, - struct serial_icounter_struct *sic) -{ - struct cyclades_port *info = tty->driver_data; - struct cyclades_icount cnow; /* Used to snapshot */ - unsigned long flags; - - spin_lock_irqsave(&info->card->card_lock, flags); - cnow = info->icount; - spin_unlock_irqrestore(&info->card->card_lock, flags); - - sic->cts = cnow.cts; - sic->dsr = cnow.dsr; - sic->rng = cnow.rng; - sic->dcd = cnow.dcd; - sic->rx = cnow.rx; - sic->tx = cnow.tx; - sic->frame = cnow.frame; - sic->overrun = cnow.overrun; - sic->parity = cnow.parity; - sic->brk = cnow.brk; - sic->buf_overrun = cnow.buf_overrun; - return 0; -} - -/* - * This routine allows the tty driver to be notified when - * device's termios settings have changed. Note that a - * well-designed tty driver should be prepared to accept the case - * where old == NULL, and try to do something rational. - */ -static void cy_set_termios(struct tty_struct *tty, struct ktermios *old_termios) -{ - struct cyclades_port *info = tty->driver_data; - -#ifdef CY_DEBUG_OTHER - printk(KERN_DEBUG "cyc:cy_set_termios ttyC%d\n", info->line); -#endif - - cy_set_line_char(info, tty); - - if ((old_termios->c_cflag & CRTSCTS) && - !(tty->termios->c_cflag & CRTSCTS)) { - tty->hw_stopped = 0; - cy_start(tty); - } -#if 0 - /* - * No need to wake up processes in open wait, since they - * sample the CLOCAL flag once, and don't recheck it. - * XXX It's not clear whether the current behavior is correct - * or not. Hence, this may change..... - */ - if (!(old_termios->c_cflag & CLOCAL) && - (tty->termios->c_cflag & CLOCAL)) - wake_up_interruptible(&info->port.open_wait); -#endif -} /* cy_set_termios */ - -/* This function is used to send a high-priority XON/XOFF character to - the device. -*/ -static void cy_send_xchar(struct tty_struct *tty, char ch) -{ - struct cyclades_port *info = tty->driver_data; - struct cyclades_card *card; - int channel; - - if (serial_paranoia_check(info, tty->name, "cy_send_xchar")) - return; - - info->x_char = ch; - - if (ch) - cy_start(tty); - - card = info->card; - channel = info->line - card->first_line; - - if (cy_is_Z(card)) { - if (ch == STOP_CHAR(tty)) - cyz_issue_cmd(card, channel, C_CM_SENDXOFF, 0L); - else if (ch == START_CHAR(tty)) - cyz_issue_cmd(card, channel, C_CM_SENDXON, 0L); - } -} - -/* This routine is called by the upper-layer tty layer to signal - that incoming characters should be throttled because the input - buffers are close to full. - */ -static void cy_throttle(struct tty_struct *tty) -{ - struct cyclades_port *info = tty->driver_data; - struct cyclades_card *card; - unsigned long flags; - -#ifdef CY_DEBUG_THROTTLE - char buf[64]; - - printk(KERN_DEBUG "cyc:throttle %s: %ld...ttyC%d\n", tty_name(tty, buf), - tty->ldisc.chars_in_buffer(tty), info->line); -#endif - - if (serial_paranoia_check(info, tty->name, "cy_throttle")) - return; - - card = info->card; - - if (I_IXOFF(tty)) { - if (!cy_is_Z(card)) - cy_send_xchar(tty, STOP_CHAR(tty)); - else - info->throttle = 1; - } - - if (tty->termios->c_cflag & CRTSCTS) { - if (!cy_is_Z(card)) { - spin_lock_irqsave(&card->card_lock, flags); - cyy_change_rts_dtr(info, 0, TIOCM_RTS); - spin_unlock_irqrestore(&card->card_lock, flags); - } else { - info->throttle = 1; - } - } -} /* cy_throttle */ - -/* - * This routine notifies the tty driver that it should signal - * that characters can now be sent to the tty without fear of - * overrunning the input buffers of the line disciplines. - */ -static void cy_unthrottle(struct tty_struct *tty) -{ - struct cyclades_port *info = tty->driver_data; - struct cyclades_card *card; - unsigned long flags; - -#ifdef CY_DEBUG_THROTTLE - char buf[64]; - - printk(KERN_DEBUG "cyc:unthrottle %s: %ld...ttyC%d\n", - tty_name(tty, buf), tty_chars_in_buffer(tty), info->line); -#endif - - if (serial_paranoia_check(info, tty->name, "cy_unthrottle")) - return; - - if (I_IXOFF(tty)) { - if (info->x_char) - info->x_char = 0; - else - cy_send_xchar(tty, START_CHAR(tty)); - } - - if (tty->termios->c_cflag & CRTSCTS) { - card = info->card; - if (!cy_is_Z(card)) { - spin_lock_irqsave(&card->card_lock, flags); - cyy_change_rts_dtr(info, TIOCM_RTS, 0); - spin_unlock_irqrestore(&card->card_lock, flags); - } else { - info->throttle = 0; - } - } -} /* cy_unthrottle */ - -/* cy_start and cy_stop provide software output flow control as a - function of XON/XOFF, software CTS, and other such stuff. -*/ -static void cy_stop(struct tty_struct *tty) -{ - struct cyclades_card *cinfo; - struct cyclades_port *info = tty->driver_data; - int channel; - unsigned long flags; - -#ifdef CY_DEBUG_OTHER - printk(KERN_DEBUG "cyc:cy_stop ttyC%d\n", info->line); -#endif - - if (serial_paranoia_check(info, tty->name, "cy_stop")) - return; - - cinfo = info->card; - channel = info->line - cinfo->first_line; - if (!cy_is_Z(cinfo)) { - spin_lock_irqsave(&cinfo->card_lock, flags); - cyy_writeb(info, CyCAR, channel & 0x03); - cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyTxRdy); - spin_unlock_irqrestore(&cinfo->card_lock, flags); - } -} /* cy_stop */ - -static void cy_start(struct tty_struct *tty) -{ - struct cyclades_card *cinfo; - struct cyclades_port *info = tty->driver_data; - int channel; - unsigned long flags; - -#ifdef CY_DEBUG_OTHER - printk(KERN_DEBUG "cyc:cy_start ttyC%d\n", info->line); -#endif - - if (serial_paranoia_check(info, tty->name, "cy_start")) - return; - - cinfo = info->card; - channel = info->line - cinfo->first_line; - if (!cy_is_Z(cinfo)) { - spin_lock_irqsave(&cinfo->card_lock, flags); - cyy_writeb(info, CyCAR, channel & 0x03); - cyy_writeb(info, CySRER, cyy_readb(info, CySRER) | CyTxRdy); - spin_unlock_irqrestore(&cinfo->card_lock, flags); - } -} /* cy_start */ - -/* - * cy_hangup() --- called by tty_hangup() when a hangup is signaled. - */ -static void cy_hangup(struct tty_struct *tty) -{ - struct cyclades_port *info = tty->driver_data; - -#ifdef CY_DEBUG_OTHER - printk(KERN_DEBUG "cyc:cy_hangup ttyC%d\n", info->line); -#endif - - if (serial_paranoia_check(info, tty->name, "cy_hangup")) - return; - - cy_flush_buffer(tty); - cy_shutdown(info, tty); - tty_port_hangup(&info->port); -} /* cy_hangup */ - -static int cyy_carrier_raised(struct tty_port *port) -{ - struct cyclades_port *info = container_of(port, struct cyclades_port, - port); - struct cyclades_card *cinfo = info->card; - unsigned long flags; - int channel = info->line - cinfo->first_line; - u32 cd; - - spin_lock_irqsave(&cinfo->card_lock, flags); - cyy_writeb(info, CyCAR, channel & 0x03); - cd = cyy_readb(info, CyMSVR1) & CyDCD; - spin_unlock_irqrestore(&cinfo->card_lock, flags); - - return cd; -} - -static void cyy_dtr_rts(struct tty_port *port, int raise) -{ - struct cyclades_port *info = container_of(port, struct cyclades_port, - port); - struct cyclades_card *cinfo = info->card; - unsigned long flags; - - spin_lock_irqsave(&cinfo->card_lock, flags); - cyy_change_rts_dtr(info, raise ? TIOCM_RTS | TIOCM_DTR : 0, - raise ? 0 : TIOCM_RTS | TIOCM_DTR); - spin_unlock_irqrestore(&cinfo->card_lock, flags); -} - -static int cyz_carrier_raised(struct tty_port *port) -{ - struct cyclades_port *info = container_of(port, struct cyclades_port, - port); - - return readl(&info->u.cyz.ch_ctrl->rs_status) & C_RS_DCD; -} - -static void cyz_dtr_rts(struct tty_port *port, int raise) -{ - struct cyclades_port *info = container_of(port, struct cyclades_port, - port); - struct cyclades_card *cinfo = info->card; - struct CH_CTRL __iomem *ch_ctrl = info->u.cyz.ch_ctrl; - int ret, channel = info->line - cinfo->first_line; - u32 rs; - - rs = readl(&ch_ctrl->rs_control); - if (raise) - rs |= C_RS_RTS | C_RS_DTR; - else - rs &= ~(C_RS_RTS | C_RS_DTR); - cy_writel(&ch_ctrl->rs_control, rs); - ret = cyz_issue_cmd(cinfo, channel, C_CM_IOCTLM, 0L); - if (ret != 0) - printk(KERN_ERR "%s: retval on ttyC%d was %x\n", - __func__, info->line, ret); -#ifdef CY_DEBUG_DTR - printk(KERN_DEBUG "%s: raising Z DTR\n", __func__); -#endif -} - -static const struct tty_port_operations cyy_port_ops = { - .carrier_raised = cyy_carrier_raised, - .dtr_rts = cyy_dtr_rts, - .shutdown = cy_do_close, -}; - -static const struct tty_port_operations cyz_port_ops = { - .carrier_raised = cyz_carrier_raised, - .dtr_rts = cyz_dtr_rts, - .shutdown = cy_do_close, -}; - -/* - * --------------------------------------------------------------------- - * cy_init() and friends - * - * cy_init() is called at boot-time to initialize the serial driver. - * --------------------------------------------------------------------- - */ - -static int __devinit cy_init_card(struct cyclades_card *cinfo) -{ - struct cyclades_port *info; - unsigned int channel, port; - - spin_lock_init(&cinfo->card_lock); - cinfo->intr_enabled = 0; - - cinfo->ports = kcalloc(cinfo->nports, sizeof(*cinfo->ports), - GFP_KERNEL); - if (cinfo->ports == NULL) { - printk(KERN_ERR "Cyclades: cannot allocate ports\n"); - return -ENOMEM; - } - - for (channel = 0, port = cinfo->first_line; channel < cinfo->nports; - channel++, port++) { - info = &cinfo->ports[channel]; - tty_port_init(&info->port); - info->magic = CYCLADES_MAGIC; - info->card = cinfo; - info->line = port; - - info->port.closing_wait = CLOSING_WAIT_DELAY; - info->port.close_delay = 5 * HZ / 10; - info->port.flags = STD_COM_FLAGS; - init_completion(&info->shutdown_wait); - - if (cy_is_Z(cinfo)) { - struct FIRM_ID *firm_id = cinfo->base_addr + ID_ADDRESS; - struct ZFW_CTRL *zfw_ctrl; - - info->port.ops = &cyz_port_ops; - info->type = PORT_STARTECH; - - zfw_ctrl = cinfo->base_addr + - (readl(&firm_id->zfwctrl_addr) & 0xfffff); - info->u.cyz.ch_ctrl = &zfw_ctrl->ch_ctrl[channel]; - info->u.cyz.buf_ctrl = &zfw_ctrl->buf_ctrl[channel]; - - if (cinfo->hw_ver == ZO_V1) - info->xmit_fifo_size = CYZ_FIFO_SIZE; - else - info->xmit_fifo_size = 4 * CYZ_FIFO_SIZE; -#ifdef CONFIG_CYZ_INTR - setup_timer(&cyz_rx_full_timer[port], - cyz_rx_restart, (unsigned long)info); -#endif - } else { - unsigned short chip_number; - int index = cinfo->bus_index; - - info->port.ops = &cyy_port_ops; - info->type = PORT_CIRRUS; - info->xmit_fifo_size = CyMAX_CHAR_FIFO; - info->cor1 = CyPARITY_NONE | Cy_1_STOP | Cy_8_BITS; - info->cor2 = CyETC; - info->cor3 = 0x08; /* _very_ small rcv threshold */ - - chip_number = channel / CyPORTS_PER_CHIP; - info->u.cyy.base_addr = cinfo->base_addr + - (cy_chip_offset[chip_number] << index); - info->chip_rev = cyy_readb(info, CyGFRCR); - - if (info->chip_rev >= CD1400_REV_J) { - /* It is a CD1400 rev. J or later */ - info->tbpr = baud_bpr_60[13]; /* Tx BPR */ - info->tco = baud_co_60[13]; /* Tx CO */ - info->rbpr = baud_bpr_60[13]; /* Rx BPR */ - info->rco = baud_co_60[13]; /* Rx CO */ - info->rtsdtr_inv = 1; - } else { - info->tbpr = baud_bpr_25[13]; /* Tx BPR */ - info->tco = baud_co_25[13]; /* Tx CO */ - info->rbpr = baud_bpr_25[13]; /* Rx BPR */ - info->rco = baud_co_25[13]; /* Rx CO */ - info->rtsdtr_inv = 0; - } - info->read_status_mask = CyTIMEOUT | CySPECHAR | - CyBREAK | CyPARITY | CyFRAME | CyOVERRUN; - } - - } - -#ifndef CONFIG_CYZ_INTR - if (cy_is_Z(cinfo) && !timer_pending(&cyz_timerlist)) { - mod_timer(&cyz_timerlist, jiffies + 1); -#ifdef CY_PCI_DEBUG - printk(KERN_DEBUG "Cyclades-Z polling initialized\n"); -#endif - } -#endif - return 0; -} - -/* initialize chips on Cyclom-Y card -- return number of valid - chips (which is number of ports/4) */ -static unsigned short __devinit cyy_init_card(void __iomem *true_base_addr, - int index) -{ - unsigned int chip_number; - void __iomem *base_addr; - - cy_writeb(true_base_addr + (Cy_HwReset << index), 0); - /* Cy_HwReset is 0x1400 */ - cy_writeb(true_base_addr + (Cy_ClrIntr << index), 0); - /* Cy_ClrIntr is 0x1800 */ - udelay(500L); - - for (chip_number = 0; chip_number < CyMAX_CHIPS_PER_CARD; - chip_number++) { - base_addr = - true_base_addr + (cy_chip_offset[chip_number] << index); - mdelay(1); - if (readb(base_addr + (CyCCR << index)) != 0x00) { - /************* - printk(" chip #%d at %#6lx is never idle (CCR != 0)\n", - chip_number, (unsigned long)base_addr); - *************/ - return chip_number; - } - - cy_writeb(base_addr + (CyGFRCR << index), 0); - udelay(10L); - - /* The Cyclom-16Y does not decode address bit 9 and therefore - cannot distinguish between references to chip 0 and a non- - existent chip 4. If the preceding clearing of the supposed - chip 4 GFRCR register appears at chip 0, there is no chip 4 - and this must be a Cyclom-16Y, not a Cyclom-32Ye. - */ - if (chip_number == 4 && readb(true_base_addr + - (cy_chip_offset[0] << index) + - (CyGFRCR << index)) == 0) { - return chip_number; - } - - cy_writeb(base_addr + (CyCCR << index), CyCHIP_RESET); - mdelay(1); - - if (readb(base_addr + (CyGFRCR << index)) == 0x00) { - /* - printk(" chip #%d at %#6lx is not responding ", - chip_number, (unsigned long)base_addr); - printk("(GFRCR stayed 0)\n", - */ - return chip_number; - } - if ((0xf0 & (readb(base_addr + (CyGFRCR << index)))) != - 0x40) { - /* - printk(" chip #%d at %#6lx is not valid (GFRCR == " - "%#2x)\n", - chip_number, (unsigned long)base_addr, - base_addr[CyGFRCR<= CD1400_REV_J) { - /* It is a CD1400 rev. J or later */ - /* Impossible to reach 5ms with this chip. - Changed to 2ms instead (f = 500 Hz). */ - cy_writeb(base_addr + (CyPPR << index), CyCLOCK_60_2MS); - } else { - /* f = 200 Hz */ - cy_writeb(base_addr + (CyPPR << index), CyCLOCK_25_5MS); - } - - /* - printk(" chip #%d at %#6lx is rev 0x%2x\n", - chip_number, (unsigned long)base_addr, - readb(base_addr+(CyGFRCR< NR_PORTS) { - printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but no " - "more channels are available. Change NR_PORTS " - "in cyclades.c and recompile kernel.\n", - (unsigned long)cy_isa_address); - iounmap(cy_isa_address); - return nboard; - } - /* fill the next cy_card structure available */ - for (j = 0; j < NR_CARDS; j++) { - if (cy_card[j].base_addr == NULL) - break; - } - if (j == NR_CARDS) { /* no more cy_cards available */ - printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but no " - "more cards can be used. Change NR_CARDS in " - "cyclades.c and recompile kernel.\n", - (unsigned long)cy_isa_address); - iounmap(cy_isa_address); - return nboard; - } - - /* allocate IRQ */ - if (request_irq(cy_isa_irq, cyy_interrupt, - IRQF_DISABLED, "Cyclom-Y", &cy_card[j])) { - printk(KERN_ERR "Cyclom-Y/ISA found at 0x%lx, but " - "could not allocate IRQ#%d.\n", - (unsigned long)cy_isa_address, cy_isa_irq); - iounmap(cy_isa_address); - return nboard; - } - - /* set cy_card */ - cy_card[j].base_addr = cy_isa_address; - cy_card[j].ctl_addr.p9050 = NULL; - cy_card[j].irq = (int)cy_isa_irq; - cy_card[j].bus_index = 0; - cy_card[j].first_line = cy_next_channel; - cy_card[j].num_chips = cy_isa_nchan / CyPORTS_PER_CHIP; - cy_card[j].nports = cy_isa_nchan; - if (cy_init_card(&cy_card[j])) { - cy_card[j].base_addr = NULL; - free_irq(cy_isa_irq, &cy_card[j]); - iounmap(cy_isa_address); - continue; - } - nboard++; - - printk(KERN_INFO "Cyclom-Y/ISA #%d: 0x%lx-0x%lx, IRQ%d found: " - "%d channels starting from port %d\n", - j + 1, (unsigned long)cy_isa_address, - (unsigned long)(cy_isa_address + (CyISA_Ywin - 1)), - cy_isa_irq, cy_isa_nchan, cy_next_channel); - - for (j = cy_next_channel; - j < cy_next_channel + cy_isa_nchan; j++) - tty_register_device(cy_serial_driver, j, NULL); - cy_next_channel += cy_isa_nchan; - } - return nboard; -#else - return 0; -#endif /* CONFIG_ISA */ -} /* cy_detect_isa */ - -#ifdef CONFIG_PCI -static inline int __devinit cyc_isfwstr(const char *str, unsigned int size) -{ - unsigned int a; - - for (a = 0; a < size && *str; a++, str++) - if (*str & 0x80) - return -EINVAL; - - for (; a < size; a++, str++) - if (*str) - return -EINVAL; - - return 0; -} - -static inline void __devinit cyz_fpga_copy(void __iomem *fpga, const u8 *data, - unsigned int size) -{ - for (; size > 0; size--) { - cy_writel(fpga, *data++); - udelay(10); - } -} - -static void __devinit plx_init(struct pci_dev *pdev, int irq, - struct RUNTIME_9060 __iomem *addr) -{ - /* Reset PLX */ - cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) | 0x40000000); - udelay(100L); - cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) & ~0x40000000); - - /* Reload Config. Registers from EEPROM */ - cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) | 0x20000000); - udelay(100L); - cy_writel(&addr->init_ctrl, readl(&addr->init_ctrl) & ~0x20000000); - - /* For some yet unknown reason, once the PLX9060 reloads the EEPROM, - * the IRQ is lost and, thus, we have to re-write it to the PCI config. - * registers. This will remain here until we find a permanent fix. - */ - pci_write_config_byte(pdev, PCI_INTERRUPT_LINE, irq); -} - -static int __devinit __cyz_load_fw(const struct firmware *fw, - const char *name, const u32 mailbox, void __iomem *base, - void __iomem *fpga) -{ - const void *ptr = fw->data; - const struct zfile_header *h = ptr; - const struct zfile_config *c, *cs; - const struct zfile_block *b, *bs; - unsigned int a, tmp, len = fw->size; -#define BAD_FW KERN_ERR "Bad firmware: " - if (len < sizeof(*h)) { - printk(BAD_FW "too short: %u<%zu\n", len, sizeof(*h)); - return -EINVAL; - } - - cs = ptr + h->config_offset; - bs = ptr + h->block_offset; - - if ((void *)(cs + h->n_config) > ptr + len || - (void *)(bs + h->n_blocks) > ptr + len) { - printk(BAD_FW "too short"); - return -EINVAL; - } - - if (cyc_isfwstr(h->name, sizeof(h->name)) || - cyc_isfwstr(h->date, sizeof(h->date))) { - printk(BAD_FW "bad formatted header string\n"); - return -EINVAL; - } - - if (strncmp(name, h->name, sizeof(h->name))) { - printk(BAD_FW "bad name '%s' (expected '%s')\n", h->name, name); - return -EINVAL; - } - - tmp = 0; - for (c = cs; c < cs + h->n_config; c++) { - for (a = 0; a < c->n_blocks; a++) - if (c->block_list[a] > h->n_blocks) { - printk(BAD_FW "bad block ref number in cfgs\n"); - return -EINVAL; - } - if (c->mailbox == mailbox && c->function == 0) /* 0 is normal */ - tmp++; - } - if (!tmp) { - printk(BAD_FW "nothing appropriate\n"); - return -EINVAL; - } - - for (b = bs; b < bs + h->n_blocks; b++) - if (b->file_offset + b->size > len) { - printk(BAD_FW "bad block data offset\n"); - return -EINVAL; - } - - /* everything is OK, let's seek'n'load it */ - for (c = cs; c < cs + h->n_config; c++) - if (c->mailbox == mailbox && c->function == 0) - break; - - for (a = 0; a < c->n_blocks; a++) { - b = &bs[c->block_list[a]]; - if (b->type == ZBLOCK_FPGA) { - if (fpga != NULL) - cyz_fpga_copy(fpga, ptr + b->file_offset, - b->size); - } else { - if (base != NULL) - memcpy_toio(base + b->ram_offset, - ptr + b->file_offset, b->size); - } - } -#undef BAD_FW - return 0; -} - -static int __devinit cyz_load_fw(struct pci_dev *pdev, void __iomem *base_addr, - struct RUNTIME_9060 __iomem *ctl_addr, int irq) -{ - const struct firmware *fw; - struct FIRM_ID __iomem *fid = base_addr + ID_ADDRESS; - struct CUSTOM_REG __iomem *cust = base_addr; - struct ZFW_CTRL __iomem *pt_zfwctrl; - void __iomem *tmp; - u32 mailbox, status, nchan; - unsigned int i; - int retval; - - retval = request_firmware(&fw, "cyzfirm.bin", &pdev->dev); - if (retval) { - dev_err(&pdev->dev, "can't get firmware\n"); - goto err; - } - - /* Check whether the firmware is already loaded and running. If - positive, skip this board */ - if (__cyz_fpga_loaded(ctl_addr) && readl(&fid->signature) == ZFIRM_ID) { - u32 cntval = readl(base_addr + 0x190); - - udelay(100); - if (cntval != readl(base_addr + 0x190)) { - /* FW counter is working, FW is running */ - dev_dbg(&pdev->dev, "Cyclades-Z FW already loaded. " - "Skipping board.\n"); - retval = 0; - goto err_rel; - } - } - - /* start boot */ - cy_writel(&ctl_addr->intr_ctrl_stat, readl(&ctl_addr->intr_ctrl_stat) & - ~0x00030800UL); - - mailbox = readl(&ctl_addr->mail_box_0); - - if (mailbox == 0 || __cyz_fpga_loaded(ctl_addr)) { - /* stops CPU and set window to beginning of RAM */ - cy_writel(&ctl_addr->loc_addr_base, WIN_CREG); - cy_writel(&cust->cpu_stop, 0); - cy_writel(&ctl_addr->loc_addr_base, WIN_RAM); - udelay(100); - } - - plx_init(pdev, irq, ctl_addr); - - if (mailbox != 0) { - /* load FPGA */ - retval = __cyz_load_fw(fw, "Cyclom-Z", mailbox, NULL, - base_addr); - if (retval) - goto err_rel; - if (!__cyz_fpga_loaded(ctl_addr)) { - dev_err(&pdev->dev, "fw upload successful, but fw is " - "not loaded\n"); - goto err_rel; - } - } - - /* stops CPU and set window to beginning of RAM */ - cy_writel(&ctl_addr->loc_addr_base, WIN_CREG); - cy_writel(&cust->cpu_stop, 0); - cy_writel(&ctl_addr->loc_addr_base, WIN_RAM); - udelay(100); - - /* clear memory */ - for (tmp = base_addr; tmp < base_addr + RAM_SIZE; tmp++) - cy_writeb(tmp, 255); - if (mailbox != 0) { - /* set window to last 512K of RAM */ - cy_writel(&ctl_addr->loc_addr_base, WIN_RAM + RAM_SIZE); - for (tmp = base_addr; tmp < base_addr + RAM_SIZE; tmp++) - cy_writeb(tmp, 255); - /* set window to beginning of RAM */ - cy_writel(&ctl_addr->loc_addr_base, WIN_RAM); - } - - retval = __cyz_load_fw(fw, "Cyclom-Z", mailbox, base_addr, NULL); - release_firmware(fw); - if (retval) - goto err; - - /* finish boot and start boards */ - cy_writel(&ctl_addr->loc_addr_base, WIN_CREG); - cy_writel(&cust->cpu_start, 0); - cy_writel(&ctl_addr->loc_addr_base, WIN_RAM); - i = 0; - while ((status = readl(&fid->signature)) != ZFIRM_ID && i++ < 40) - msleep(100); - if (status != ZFIRM_ID) { - if (status == ZFIRM_HLT) { - dev_err(&pdev->dev, "you need an external power supply " - "for this number of ports. Firmware halted and " - "board reset.\n"); - retval = -EIO; - goto err; - } - dev_warn(&pdev->dev, "fid->signature = 0x%x... Waiting " - "some more time\n", status); - while ((status = readl(&fid->signature)) != ZFIRM_ID && - i++ < 200) - msleep(100); - if (status != ZFIRM_ID) { - dev_err(&pdev->dev, "Board not started in 20 seconds! " - "Giving up. (fid->signature = 0x%x)\n", - status); - dev_info(&pdev->dev, "*** Warning ***: if you are " - "upgrading the FW, please power cycle the " - "system before loading the new FW to the " - "Cyclades-Z.\n"); - - if (__cyz_fpga_loaded(ctl_addr)) - plx_init(pdev, irq, ctl_addr); - - retval = -EIO; - goto err; - } - dev_dbg(&pdev->dev, "Firmware started after %d seconds.\n", - i / 10); - } - pt_zfwctrl = base_addr + readl(&fid->zfwctrl_addr); - - dev_dbg(&pdev->dev, "fid=> %p, zfwctrl_addr=> %x, npt_zfwctrl=> %p\n", - base_addr + ID_ADDRESS, readl(&fid->zfwctrl_addr), - base_addr + readl(&fid->zfwctrl_addr)); - - nchan = readl(&pt_zfwctrl->board_ctrl.n_channel); - dev_info(&pdev->dev, "Cyclades-Z FW loaded: version = %x, ports = %u\n", - readl(&pt_zfwctrl->board_ctrl.fw_version), nchan); - - if (nchan == 0) { - dev_warn(&pdev->dev, "no Cyclades-Z ports were found. Please " - "check the connection between the Z host card and the " - "serial expanders.\n"); - - if (__cyz_fpga_loaded(ctl_addr)) - plx_init(pdev, irq, ctl_addr); - - dev_info(&pdev->dev, "Null number of ports detected. Board " - "reset.\n"); - retval = 0; - goto err; - } - - cy_writel(&pt_zfwctrl->board_ctrl.op_system, C_OS_LINUX); - cy_writel(&pt_zfwctrl->board_ctrl.dr_version, DRIVER_VERSION); - - /* - Early firmware failed to start looking for commands. - This enables firmware interrupts for those commands. - */ - cy_writel(&ctl_addr->intr_ctrl_stat, readl(&ctl_addr->intr_ctrl_stat) | - (1 << 17)); - cy_writel(&ctl_addr->intr_ctrl_stat, readl(&ctl_addr->intr_ctrl_stat) | - 0x00030800UL); - - return nchan; -err_rel: - release_firmware(fw); -err: - return retval; -} - -static int __devinit cy_pci_probe(struct pci_dev *pdev, - const struct pci_device_id *ent) -{ - void __iomem *addr0 = NULL, *addr2 = NULL; - char *card_name = NULL; - u32 uninitialized_var(mailbox); - unsigned int device_id, nchan = 0, card_no, i; - unsigned char plx_ver; - int retval, irq; - - retval = pci_enable_device(pdev); - if (retval) { - dev_err(&pdev->dev, "cannot enable device\n"); - goto err; - } - - /* read PCI configuration area */ - irq = pdev->irq; - device_id = pdev->device & ~PCI_DEVICE_ID_MASK; - -#if defined(__alpha__) - if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo) { /* below 1M? */ - dev_err(&pdev->dev, "Cyclom-Y/PCI not supported for low " - "addresses on Alpha systems.\n"); - retval = -EIO; - goto err_dis; - } -#endif - if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Lo) { - dev_err(&pdev->dev, "Cyclades-Z/PCI not supported for low " - "addresses\n"); - retval = -EIO; - goto err_dis; - } - - if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) { - dev_warn(&pdev->dev, "PCI I/O bit incorrectly set. Ignoring " - "it...\n"); - pdev->resource[2].flags &= ~IORESOURCE_IO; - } - - retval = pci_request_regions(pdev, "cyclades"); - if (retval) { - dev_err(&pdev->dev, "failed to reserve resources\n"); - goto err_dis; - } - - retval = -EIO; - if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo || - device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) { - card_name = "Cyclom-Y"; - - addr0 = ioremap_nocache(pci_resource_start(pdev, 0), - CyPCI_Yctl); - if (addr0 == NULL) { - dev_err(&pdev->dev, "can't remap ctl region\n"); - goto err_reg; - } - addr2 = ioremap_nocache(pci_resource_start(pdev, 2), - CyPCI_Ywin); - if (addr2 == NULL) { - dev_err(&pdev->dev, "can't remap base region\n"); - goto err_unmap; - } - - nchan = CyPORTS_PER_CHIP * cyy_init_card(addr2, 1); - if (nchan == 0) { - dev_err(&pdev->dev, "Cyclom-Y PCI host card with no " - "Serial-Modules\n"); - goto err_unmap; - } - } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Hi) { - struct RUNTIME_9060 __iomem *ctl_addr; - - ctl_addr = addr0 = ioremap_nocache(pci_resource_start(pdev, 0), - CyPCI_Zctl); - if (addr0 == NULL) { - dev_err(&pdev->dev, "can't remap ctl region\n"); - goto err_reg; - } - - /* Disable interrupts on the PLX before resetting it */ - cy_writew(&ctl_addr->intr_ctrl_stat, - readw(&ctl_addr->intr_ctrl_stat) & ~0x0900); - - plx_init(pdev, irq, addr0); - - mailbox = readl(&ctl_addr->mail_box_0); - - addr2 = ioremap_nocache(pci_resource_start(pdev, 2), - mailbox == ZE_V1 ? CyPCI_Ze_win : CyPCI_Zwin); - if (addr2 == NULL) { - dev_err(&pdev->dev, "can't remap base region\n"); - goto err_unmap; - } - - if (mailbox == ZE_V1) { - card_name = "Cyclades-Ze"; - } else { - card_name = "Cyclades-8Zo"; -#ifdef CY_PCI_DEBUG - if (mailbox == ZO_V1) { - cy_writel(&ctl_addr->loc_addr_base, WIN_CREG); - dev_info(&pdev->dev, "Cyclades-8Zo/PCI: FPGA " - "id %lx, ver %lx\n", (ulong)(0xff & - readl(&((struct CUSTOM_REG *)addr2)-> - fpga_id)), (ulong)(0xff & - readl(&((struct CUSTOM_REG *)addr2)-> - fpga_version))); - cy_writel(&ctl_addr->loc_addr_base, WIN_RAM); - } else { - dev_info(&pdev->dev, "Cyclades-Z/PCI: New " - "Cyclades-Z board. FPGA not loaded\n"); - } -#endif - /* The following clears the firmware id word. This - ensures that the driver will not attempt to talk to - the board until it has been properly initialized. - */ - if ((mailbox == ZO_V1) || (mailbox == ZO_V2)) - cy_writel(addr2 + ID_ADDRESS, 0L); - } - - retval = cyz_load_fw(pdev, addr2, addr0, irq); - if (retval <= 0) - goto err_unmap; - nchan = retval; - } - - if ((cy_next_channel + nchan) > NR_PORTS) { - dev_err(&pdev->dev, "Cyclades-8Zo/PCI found, but no " - "channels are available. Change NR_PORTS in " - "cyclades.c and recompile kernel.\n"); - goto err_unmap; - } - /* fill the next cy_card structure available */ - for (card_no = 0; card_no < NR_CARDS; card_no++) { - if (cy_card[card_no].base_addr == NULL) - break; - } - if (card_no == NR_CARDS) { /* no more cy_cards available */ - dev_err(&pdev->dev, "Cyclades-8Zo/PCI found, but no " - "more cards can be used. Change NR_CARDS in " - "cyclades.c and recompile kernel.\n"); - goto err_unmap; - } - - if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo || - device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) { - /* allocate IRQ */ - retval = request_irq(irq, cyy_interrupt, - IRQF_SHARED, "Cyclom-Y", &cy_card[card_no]); - if (retval) { - dev_err(&pdev->dev, "could not allocate IRQ\n"); - goto err_unmap; - } - cy_card[card_no].num_chips = nchan / CyPORTS_PER_CHIP; - } else { - struct FIRM_ID __iomem *firm_id = addr2 + ID_ADDRESS; - struct ZFW_CTRL __iomem *zfw_ctrl; - - zfw_ctrl = addr2 + (readl(&firm_id->zfwctrl_addr) & 0xfffff); - - cy_card[card_no].hw_ver = mailbox; - cy_card[card_no].num_chips = (unsigned int)-1; - cy_card[card_no].board_ctrl = &zfw_ctrl->board_ctrl; -#ifdef CONFIG_CYZ_INTR - /* allocate IRQ only if board has an IRQ */ - if (irq != 0 && irq != 255) { - retval = request_irq(irq, cyz_interrupt, - IRQF_SHARED, "Cyclades-Z", - &cy_card[card_no]); - if (retval) { - dev_err(&pdev->dev, "could not allocate IRQ\n"); - goto err_unmap; - } - } -#endif /* CONFIG_CYZ_INTR */ - } - - /* set cy_card */ - cy_card[card_no].base_addr = addr2; - cy_card[card_no].ctl_addr.p9050 = addr0; - cy_card[card_no].irq = irq; - cy_card[card_no].bus_index = 1; - cy_card[card_no].first_line = cy_next_channel; - cy_card[card_no].nports = nchan; - retval = cy_init_card(&cy_card[card_no]); - if (retval) - goto err_null; - - pci_set_drvdata(pdev, &cy_card[card_no]); - - if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo || - device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) { - /* enable interrupts in the PCI interface */ - plx_ver = readb(addr2 + CyPLX_VER) & 0x0f; - switch (plx_ver) { - case PLX_9050: - cy_writeb(addr0 + 0x4c, 0x43); - break; - - case PLX_9060: - case PLX_9080: - default: /* Old boards, use PLX_9060 */ - { - struct RUNTIME_9060 __iomem *ctl_addr = addr0; - plx_init(pdev, irq, ctl_addr); - cy_writew(&ctl_addr->intr_ctrl_stat, - readw(&ctl_addr->intr_ctrl_stat) | 0x0900); - break; - } - } - } - - dev_info(&pdev->dev, "%s/PCI #%d found: %d channels starting from " - "port %d.\n", card_name, card_no + 1, nchan, cy_next_channel); - for (i = cy_next_channel; i < cy_next_channel + nchan; i++) - tty_register_device(cy_serial_driver, i, &pdev->dev); - cy_next_channel += nchan; - - return 0; -err_null: - cy_card[card_no].base_addr = NULL; - free_irq(irq, &cy_card[card_no]); -err_unmap: - iounmap(addr0); - if (addr2) - iounmap(addr2); -err_reg: - pci_release_regions(pdev); -err_dis: - pci_disable_device(pdev); -err: - return retval; -} - -static void __devexit cy_pci_remove(struct pci_dev *pdev) -{ - struct cyclades_card *cinfo = pci_get_drvdata(pdev); - unsigned int i; - - /* non-Z with old PLX */ - if (!cy_is_Z(cinfo) && (readb(cinfo->base_addr + CyPLX_VER) & 0x0f) == - PLX_9050) - cy_writeb(cinfo->ctl_addr.p9050 + 0x4c, 0); - else -#ifndef CONFIG_CYZ_INTR - if (!cy_is_Z(cinfo)) -#endif - cy_writew(&cinfo->ctl_addr.p9060->intr_ctrl_stat, - readw(&cinfo->ctl_addr.p9060->intr_ctrl_stat) & - ~0x0900); - - iounmap(cinfo->base_addr); - if (cinfo->ctl_addr.p9050) - iounmap(cinfo->ctl_addr.p9050); - if (cinfo->irq -#ifndef CONFIG_CYZ_INTR - && !cy_is_Z(cinfo) -#endif /* CONFIG_CYZ_INTR */ - ) - free_irq(cinfo->irq, cinfo); - pci_release_regions(pdev); - - cinfo->base_addr = NULL; - for (i = cinfo->first_line; i < cinfo->first_line + - cinfo->nports; i++) - tty_unregister_device(cy_serial_driver, i); - cinfo->nports = 0; - kfree(cinfo->ports); -} - -static struct pci_driver cy_pci_driver = { - .name = "cyclades", - .id_table = cy_pci_dev_id, - .probe = cy_pci_probe, - .remove = __devexit_p(cy_pci_remove) -}; -#endif - -static int cyclades_proc_show(struct seq_file *m, void *v) -{ - struct cyclades_port *info; - unsigned int i, j; - __u32 cur_jifs = jiffies; - - seq_puts(m, "Dev TimeOpen BytesOut IdleOut BytesIn " - "IdleIn Overruns Ldisc\n"); - - /* Output one line for each known port */ - for (i = 0; i < NR_CARDS; i++) - for (j = 0; j < cy_card[i].nports; j++) { - info = &cy_card[i].ports[j]; - - if (info->port.count) { - /* XXX is the ldisc num worth this? */ - struct tty_struct *tty; - struct tty_ldisc *ld; - int num = 0; - tty = tty_port_tty_get(&info->port); - if (tty) { - ld = tty_ldisc_ref(tty); - if (ld) { - num = ld->ops->num; - tty_ldisc_deref(ld); - } - tty_kref_put(tty); - } - seq_printf(m, "%3d %8lu %10lu %8lu " - "%10lu %8lu %9lu %6d\n", info->line, - (cur_jifs - info->idle_stats.in_use) / - HZ, info->idle_stats.xmit_bytes, - (cur_jifs - info->idle_stats.xmit_idle)/ - HZ, info->idle_stats.recv_bytes, - (cur_jifs - info->idle_stats.recv_idle)/ - HZ, info->idle_stats.overruns, - num); - } else - seq_printf(m, "%3d %8lu %10lu %8lu " - "%10lu %8lu %9lu %6ld\n", - info->line, 0L, 0L, 0L, 0L, 0L, 0L, 0L); - } - return 0; -} - -static int cyclades_proc_open(struct inode *inode, struct file *file) -{ - return single_open(file, cyclades_proc_show, NULL); -} - -static const struct file_operations cyclades_proc_fops = { - .owner = THIS_MODULE, - .open = cyclades_proc_open, - .read = seq_read, - .llseek = seq_lseek, - .release = single_release, -}; - -/* The serial driver boot-time initialization code! - Hardware I/O ports are mapped to character special devices on a - first found, first allocated manner. That is, this code searches - for Cyclom cards in the system. As each is found, it is probed - to discover how many chips (and thus how many ports) are present. - These ports are mapped to the tty ports 32 and upward in monotonic - fashion. If an 8-port card is replaced with a 16-port card, the - port mapping on a following card will shift. - - This approach is different from what is used in the other serial - device driver because the Cyclom is more properly a multiplexer, - not just an aggregation of serial ports on one card. - - If there are more cards with more ports than have been - statically allocated above, a warning is printed and the - extra ports are ignored. - */ - -static const struct tty_operations cy_ops = { - .open = cy_open, - .close = cy_close, - .write = cy_write, - .put_char = cy_put_char, - .flush_chars = cy_flush_chars, - .write_room = cy_write_room, - .chars_in_buffer = cy_chars_in_buffer, - .flush_buffer = cy_flush_buffer, - .ioctl = cy_ioctl, - .throttle = cy_throttle, - .unthrottle = cy_unthrottle, - .set_termios = cy_set_termios, - .stop = cy_stop, - .start = cy_start, - .hangup = cy_hangup, - .break_ctl = cy_break, - .wait_until_sent = cy_wait_until_sent, - .tiocmget = cy_tiocmget, - .tiocmset = cy_tiocmset, - .get_icount = cy_get_icount, - .proc_fops = &cyclades_proc_fops, -}; - -static int __init cy_init(void) -{ - unsigned int nboards; - int retval = -ENOMEM; - - cy_serial_driver = alloc_tty_driver(NR_PORTS); - if (!cy_serial_driver) - goto err; - - printk(KERN_INFO "Cyclades driver " CY_VERSION " (built %s %s)\n", - __DATE__, __TIME__); - - /* Initialize the tty_driver structure */ - - cy_serial_driver->owner = THIS_MODULE; - cy_serial_driver->driver_name = "cyclades"; - cy_serial_driver->name = "ttyC"; - cy_serial_driver->major = CYCLADES_MAJOR; - cy_serial_driver->minor_start = 0; - cy_serial_driver->type = TTY_DRIVER_TYPE_SERIAL; - cy_serial_driver->subtype = SERIAL_TYPE_NORMAL; - cy_serial_driver->init_termios = tty_std_termios; - cy_serial_driver->init_termios.c_cflag = - B9600 | CS8 | CREAD | HUPCL | CLOCAL; - cy_serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV; - tty_set_operations(cy_serial_driver, &cy_ops); - - retval = tty_register_driver(cy_serial_driver); - if (retval) { - printk(KERN_ERR "Couldn't register Cyclades serial driver\n"); - goto err_frtty; - } - - /* the code below is responsible to find the boards. Each different - type of board has its own detection routine. If a board is found, - the next cy_card structure available is set by the detection - routine. These functions are responsible for checking the - availability of cy_card and cy_port data structures and updating - the cy_next_channel. */ - - /* look for isa boards */ - nboards = cy_detect_isa(); - -#ifdef CONFIG_PCI - /* look for pci boards */ - retval = pci_register_driver(&cy_pci_driver); - if (retval && !nboards) { - tty_unregister_driver(cy_serial_driver); - goto err_frtty; - } -#endif - - return 0; -err_frtty: - put_tty_driver(cy_serial_driver); -err: - return retval; -} /* cy_init */ - -static void __exit cy_cleanup_module(void) -{ - struct cyclades_card *card; - unsigned int i, e1; - -#ifndef CONFIG_CYZ_INTR - del_timer_sync(&cyz_timerlist); -#endif /* CONFIG_CYZ_INTR */ - - e1 = tty_unregister_driver(cy_serial_driver); - if (e1) - printk(KERN_ERR "failed to unregister Cyclades serial " - "driver(%d)\n", e1); - -#ifdef CONFIG_PCI - pci_unregister_driver(&cy_pci_driver); -#endif - - for (i = 0; i < NR_CARDS; i++) { - card = &cy_card[i]; - if (card->base_addr) { - /* clear interrupt */ - cy_writeb(card->base_addr + Cy_ClrIntr, 0); - iounmap(card->base_addr); - if (card->ctl_addr.p9050) - iounmap(card->ctl_addr.p9050); - if (card->irq -#ifndef CONFIG_CYZ_INTR - && !cy_is_Z(card) -#endif /* CONFIG_CYZ_INTR */ - ) - free_irq(card->irq, card); - for (e1 = card->first_line; e1 < card->first_line + - card->nports; e1++) - tty_unregister_device(cy_serial_driver, e1); - kfree(card->ports); - } - } - - put_tty_driver(cy_serial_driver); -} /* cy_cleanup_module */ - -module_init(cy_init); -module_exit(cy_cleanup_module); - -MODULE_LICENSE("GPL"); -MODULE_VERSION(CY_VERSION); -MODULE_ALIAS_CHARDEV_MAJOR(CYCLADES_MAJOR); -MODULE_FIRMWARE("cyzfirm.bin"); -- cgit v1.1