From c9b24996d5da1bf7d2bebab5770dfcc7834c53b7 Mon Sep 17 00:00:00 2001 From: Andreas Herrmann Date: Fri, 27 Sep 2013 00:36:15 +0200 Subject: ARM: dma-mapping: Always pass proper prot flags to iommu_map() ... otherwise it is impossible for the low level iommu driver to figure out which pte flags should be used. In __map_sg_chunk we can derive the flags from dma_data_direction. In __iommu_create_mapping we should treat the memory like DMA_BIDIRECTIONAL and pass both IOMMU_READ and IOMMU_WRITE to iommu_map. __iommu_create_mapping is used during dma_alloc_coherent (via arm_iommu_alloc_attrs). AFAIK dma_alloc_coherent is responsible for allocation _and_ mapping. I think this implies that access to the mapped pages should be allowed. Cc: Marek Szyprowski Signed-off-by: Andreas Herrmann Acked-by: Will Deacon Signed-off-by: Marek Szyprowski --- arch/arm/mm/dma-mapping.c | 43 ++++++++++++++++++++++++++++--------------- 1 file changed, 28 insertions(+), 15 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c index f5e1a84..1272ed2 100644 --- a/arch/arm/mm/dma-mapping.c +++ b/arch/arm/mm/dma-mapping.c @@ -1232,7 +1232,8 @@ __iommu_create_mapping(struct device *dev, struct page **pages, size_t size) break; len = (j - i) << PAGE_SHIFT; - ret = iommu_map(mapping->domain, iova, phys, len, 0); + ret = iommu_map(mapping->domain, iova, phys, len, + IOMMU_READ|IOMMU_WRITE); if (ret < 0) goto fail; iova += len; @@ -1431,6 +1432,27 @@ static int arm_iommu_get_sgtable(struct device *dev, struct sg_table *sgt, GFP_KERNEL); } +static int __dma_direction_to_prot(enum dma_data_direction dir) +{ + int prot; + + switch (dir) { + case DMA_BIDIRECTIONAL: + prot = IOMMU_READ | IOMMU_WRITE; + break; + case DMA_TO_DEVICE: + prot = IOMMU_READ; + break; + case DMA_FROM_DEVICE: + prot = IOMMU_WRITE; + break; + default: + prot = 0; + } + + return prot; +} + /* * Map a part of the scatter-gather list into contiguous io address space */ @@ -1444,6 +1466,7 @@ static int __map_sg_chunk(struct device *dev, struct scatterlist *sg, int ret = 0; unsigned int count; struct scatterlist *s; + int prot; size = PAGE_ALIGN(size); *handle = DMA_ERROR_CODE; @@ -1460,7 +1483,9 @@ static int __map_sg_chunk(struct device *dev, struct scatterlist *sg, !dma_get_attr(DMA_ATTR_SKIP_CPU_SYNC, attrs)) __dma_page_cpu_to_dev(sg_page(s), s->offset, s->length, dir); - ret = iommu_map(mapping->domain, iova, phys, len, 0); + prot = __dma_direction_to_prot(dir); + + ret = iommu_map(mapping->domain, iova, phys, len, prot); if (ret < 0) goto fail; count += len >> PAGE_SHIFT; @@ -1665,19 +1690,7 @@ static dma_addr_t arm_coherent_iommu_map_page(struct device *dev, struct page *p if (dma_addr == DMA_ERROR_CODE) return dma_addr; - switch (dir) { - case DMA_BIDIRECTIONAL: - prot = IOMMU_READ | IOMMU_WRITE; - break; - case DMA_TO_DEVICE: - prot = IOMMU_READ; - break; - case DMA_FROM_DEVICE: - prot = IOMMU_WRITE; - break; - default: - prot = 0; - } + prot = __dma_direction_to_prot(dir); ret = iommu_map(mapping->domain, dma_addr, page_to_phys(page), len, prot); if (ret < 0) -- cgit v1.1 From d0cdef6e87ebc1241d7e407d5e1b14e6bb836ae9 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Wed, 25 Sep 2013 23:26:24 +0100 Subject: ARM: 7842/1: MCPM: don't explode if invoked without being initialized first Currently mcpm_cpu_power_down() and mcpm_cpu_suspend() trigger BUG() if mcpm_platform_register() is not called beforehand. This may occur for many reasons such as some incomplete device tree passed to the kernel or the like. Let's be nicer to users and avoid killing the kernel if that happens by logging a warning and returning to the caller. The mcpm_cpu_suspend() user is already set to deal with this situation, and so is cpu_die() invoking mcpm_cpu_die(). The problematic case would have been the B.L switcher's usage of mcpm_cpu_power_down(), however it has to call mcpm_cpu_power_up() first which is already set to catch an error resulting from a missing mcpm_platform_register() call. Signed-off-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/common/mcpm_entry.c | 6 ++++-- arch/arm/include/asm/mcpm.h | 14 ++++++++++---- 2 files changed, 14 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/arm/common/mcpm_entry.c b/arch/arm/common/mcpm_entry.c index 370236d..9902509 100644 --- a/arch/arm/common/mcpm_entry.c +++ b/arch/arm/common/mcpm_entry.c @@ -51,7 +51,8 @@ void mcpm_cpu_power_down(void) { phys_reset_t phys_reset; - BUG_ON(!platform_ops); + if (WARN_ON_ONCE(!platform_ops || !platform_ops->power_down)) + return; BUG_ON(!irqs_disabled()); /* @@ -93,7 +94,8 @@ void mcpm_cpu_suspend(u64 expected_residency) { phys_reset_t phys_reset; - BUG_ON(!platform_ops); + if (WARN_ON_ONCE(!platform_ops || !platform_ops->suspend)) + return; BUG_ON(!irqs_disabled()); /* Very similar to mcpm_cpu_power_down() */ diff --git a/arch/arm/include/asm/mcpm.h b/arch/arm/include/asm/mcpm.h index 0f7b762..fc82a88 100644 --- a/arch/arm/include/asm/mcpm.h +++ b/arch/arm/include/asm/mcpm.h @@ -76,8 +76,11 @@ int mcpm_cpu_power_up(unsigned int cpu, unsigned int cluster); * * This must be called with interrupts disabled. * - * This does not return. Re-entry in the kernel is expected via - * mcpm_entry_point. + * On success this does not return. Re-entry in the kernel is expected + * via mcpm_entry_point. + * + * This will return if mcpm_platform_register() has not been called + * previously in which case the caller should take appropriate action. */ void mcpm_cpu_power_down(void); @@ -98,8 +101,11 @@ void mcpm_cpu_power_down(void); * * This must be called with interrupts disabled. * - * This does not return. Re-entry in the kernel is expected via - * mcpm_entry_point. + * On success this does not return. Re-entry in the kernel is expected + * via mcpm_entry_point. + * + * This will return if mcpm_platform_register() has not been called + * previously in which case the caller should take appropriate action. */ void mcpm_cpu_suspend(u64 expected_residency); -- cgit v1.1 From 262576fffe425ee7768f2686ad5536907d828764 Mon Sep 17 00:00:00 2001 From: Ard Biesheuvel Date: Thu, 26 Sep 2013 15:07:23 +0100 Subject: ARM: 7843/1: drop asm/types.h from generic-y Commit 09096f6 (ARM: 7822/1: add workaround for ambiguous C99 stdint.h types) introduced an ARM specific 'asm/types.h' to work around some ambiguities in the definitions of 32 bit types. Hence, we will not be needing the generic version anymore. Signed-off-by: Ard Biesheuvel Signed-off-by: Russell King --- arch/arm/include/asm/Kbuild | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/include/asm/Kbuild b/arch/arm/include/asm/Kbuild index d3db398..59ceae8 100644 --- a/arch/arm/include/asm/Kbuild +++ b/arch/arm/include/asm/Kbuild @@ -31,5 +31,4 @@ generic-y += termbits.h generic-y += termios.h generic-y += timex.h generic-y += trace_clock.h -generic-y += types.h generic-y += unaligned.h -- cgit v1.1 From 856337283a215b9f92189f22862e4415f4d6bd85 Mon Sep 17 00:00:00 2001 From: Andrea Adami Date: Thu, 26 Sep 2013 23:23:02 +0100 Subject: ARM: 7845/1: sharpsl_param.c: fix invalid memory access for pxa devices This fixes a regression for kernels after v3.2 After commit 72662e01088394577be4a3f14da94cf87bea2591 ARM: head.S: only include __turn_mmu_on in the initial identity mapping Zaurus PXA devices call sharpsl_save_param() during fixup and hang on boot because memcpy refers to physical addresses no longer valid if the MMU is setup. Zaurus collie (SA1100) is unaffected (function is called in init_machine). The code was making assumptions and for PXA the virtual address should have been used before. Signed-off-by: Marko Katic Signed-off-by: Andrea Adami Signed-off-by: Russell King --- arch/arm/common/sharpsl_param.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/common/sharpsl_param.c b/arch/arm/common/sharpsl_param.c index d56c932..025f6ce 100644 --- a/arch/arm/common/sharpsl_param.c +++ b/arch/arm/common/sharpsl_param.c @@ -15,6 +15,7 @@ #include #include #include +#include /* * Certain hardware parameters determined at the time of device manufacture, @@ -25,8 +26,10 @@ */ #ifdef CONFIG_ARCH_SA1100 #define PARAM_BASE 0xe8ffc000 +#define param_start(x) (void *)(x) #else #define PARAM_BASE 0xa0000a00 +#define param_start(x) __va(x) #endif #define MAGIC_CHG(a,b,c,d) ( ( d << 24 ) | ( c << 16 ) | ( b << 8 ) | a ) @@ -41,7 +44,7 @@ EXPORT_SYMBOL(sharpsl_param); void sharpsl_save_param(void) { - memcpy(&sharpsl_param, (void *)PARAM_BASE, sizeof(struct sharpsl_param_info)); + memcpy(&sharpsl_param, param_start(PARAM_BASE), sizeof(struct sharpsl_param_info)); if (sharpsl_param.comadj_keyword != COMADJ_MAGIC) sharpsl_param.comadj=-1; -- cgit v1.1 From bc41b8724f24b9a27d1dcc6c974b8f686b38d554 Mon Sep 17 00:00:00 2001 From: Santosh Shilimkar Date: Fri, 27 Sep 2013 21:56:31 +0100 Subject: ARM: 7846/1: Update SMP_ON_UP code to detect A9MPCore with 1 CPU devices The generic code is well equipped to differentiate between SMP and UP configurations.However, there are some devices which use Cortex-A9 MP core IP with 1 CPU as configuration. To let these SOCs to co-exist in a CONFIG_SMP=y build by leveraging the SMP_ON_UP support, we need to additionally check the number the cores in Cortex-A9 MPCore configuration. Without such a check in place, the startup code tries to execute ALT_SMP() set of instructions which lead to CPU faults. The issue was spotted on TI's Aegis device and this patch makes now the device work with omap2plus_defconfig which enables SMP by default. The change is kept limited to only Cortex-A9 MPCore detection code. Note that if any future SoC *does* use 0x0 as the PERIPH_BASE, then the SCU address check code needs to be #ifdef'd for for the Aegis platform. Acked-by: Sricharan R Signed-off-by: Vaibhav Bedia Signed-off-by: Santosh Shilimkar Signed-off-by: Russell King --- arch/arm/kernel/head.S | 21 ++++++++++++++++++++- 1 file changed, 20 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S index 2c7cc1e..476de57 100644 --- a/arch/arm/kernel/head.S +++ b/arch/arm/kernel/head.S @@ -487,7 +487,26 @@ __fixup_smp: mrc p15, 0, r0, c0, c0, 5 @ read MPIDR and r0, r0, #0xc0000000 @ multiprocessing extensions and teq r0, #0x80000000 @ not part of a uniprocessor system? - moveq pc, lr @ yes, assume SMP + bne __fixup_smp_on_up @ no, assume UP + + @ Core indicates it is SMP. Check for Aegis SOC where a single + @ Cortex-A9 CPU is present but SMP operations fault. + mov r4, #0x41000000 + orr r4, r4, #0x0000c000 + orr r4, r4, #0x00000090 + teq r3, r4 @ Check for ARM Cortex-A9 + movne pc, lr @ Not ARM Cortex-A9, + + @ If a future SoC *does* use 0x0 as the PERIPH_BASE, then the + @ below address check will need to be #ifdef'd or equivalent + @ for the Aegis platform. + mrc p15, 4, r0, c15, c0 @ get SCU base address + teq r0, #0x0 @ '0' on actual UP A9 hardware + beq __fixup_smp_on_up @ So its an A9 UP + ldr r0, [r0, #4] @ read SCU Config + and r0, r0, #0x3 @ number of CPUs + teq r0, #0x0 @ is 1? + movne pc, lr __fixup_smp_on_up: adr r0, 1f -- cgit v1.1 From 1dc1c33879bf47500565e627506f3d4e150e1cae Mon Sep 17 00:00:00 2001 From: Aaro Koskinen Date: Fri, 20 Sep 2013 23:01:06 +0300 Subject: ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT With DT-based boot, the GPMC OneNAND sync mode setup does not work correctly. During the async mode setup, sync flags gets incorrectly set in the onenand_async data and the system crashes during the async setup. Also, the sync mode never gets set in gpmc_onenand_data->flags, so even without the crash, the actual sync mode setup would never be called. The patch fixes this by adjusting the gpmc_onenand_data->flags when the data is read from the DT. Also while doing this we force the onenand_async to be always async. The patch enables to use the following DTS chunk (that should correspond the arch/arm/mach-omap2/board-rm680.c board file setup) with Nokia N950, which currently crashes with 3.12-rc1. The crash output can be also found below. &gpmc { ranges = <0 0 0x04000000 0x20000000>; onenand@0,0 { #address-cells = <1>; #size-cells = <1>; reg = <0 0 0x20000000>; gpmc,sync-read; gpmc,sync-write; gpmc,burst-length = <16>; gpmc,burst-read; gpmc,burst-wrap; gpmc,burst-write; gpmc,device-width = <2>; gpmc,mux-add-data = <2>; gpmc,cs-on-ns = <0>; gpmc,cs-rd-off-ns = <87>; gpmc,cs-wr-off-ns = <87>; gpmc,adv-on-ns = <0>; gpmc,adv-rd-off-ns = <10>; gpmc,adv-wr-off-ns = <10>; gpmc,oe-on-ns = <15>; gpmc,oe-off-ns = <87>; gpmc,we-on-ns = <0>; gpmc,we-off-ns = <87>; gpmc,rd-cycle-ns = <112>; gpmc,wr-cycle-ns = <112>; gpmc,access-ns = <81>; gpmc,page-burst-access-ns = <15>; gpmc,bus-turnaround-ns = <0>; gpmc,cycle2cycle-delay-ns = <0>; gpmc,wait-monitoring-ns = <0>; gpmc,clk-activation-ns = <5>; gpmc,wr-data-mux-bus-ns = <30>; gpmc,wr-access-ns = <81>; gpmc,sync-clk-ps = <15000>; }; }; [ 1.467559] GPMC CS0: cs_on : 0 ticks, 0 ns (was 0 ticks) 0 ns [ 1.474822] GPMC CS0: cs_rd_off : 1 ticks, 5 ns (was 24 ticks) 5 ns [ 1.482116] GPMC CS0: cs_wr_off : 14 ticks, 71 ns (was 24 ticks) 71 ns [ 1.489349] GPMC CS0: adv_on : 0 ticks, 0 ns (was 0 ticks) 0 ns [ 1.496582] GPMC CS0: adv_rd_off: 3 ticks, 15 ns (was 3 ticks) 15 ns [ 1.503845] GPMC CS0: adv_wr_off: 3 ticks, 15 ns (was 3 ticks) 15 ns [ 1.511077] GPMC CS0: oe_on : 3 ticks, 15 ns (was 4 ticks) 15 ns [ 1.518310] GPMC CS0: oe_off : 1 ticks, 5 ns (was 24 ticks) 5 ns [ 1.525543] GPMC CS0: we_on : 0 ticks, 0 ns (was 0 ticks) 0 ns [ 1.532806] GPMC CS0: we_off : 8 ticks, 40 ns (was 24 ticks) 40 ns [ 1.540039] GPMC CS0: rd_cycle : 4 ticks, 20 ns (was 29 ticks) 20 ns [ 1.547302] GPMC CS0: wr_cycle : 4 ticks, 20 ns (was 29 ticks) 20 ns [ 1.554504] GPMC CS0: access : 0 ticks, 0 ns (was 23 ticks) 0 ns [ 1.561767] GPMC CS0: page_burst_access: 0 ticks, 0 ns (was 3 ticks) 0 ns [ 1.569641] GPMC CS0: bus_turnaround: 0 ticks, 0 ns (was 0 ticks) 0 ns [ 1.577270] GPMC CS0: cycle2cycle_delay: 0 ticks, 0 ns (was 0 ticks) 0 ns [ 1.585144] GPMC CS0: wait_monitoring: 0 ticks, 0 ns (was 0 ticks) 0 ns [ 1.592834] GPMC CS0: clk_activation: 0 ticks, 0 ns (was 0 ticks) 0 ns [ 1.600463] GPMC CS0: wr_data_mux_bus: 5 ticks, 25 ns (was 8 ticks) 25 ns [ 1.608154] GPMC CS0: wr_access : 0 ticks, 0 ns (was 23 ticks) 0 ns [ 1.615386] GPMC CS0 CLK period is 5 ns (div 1) [ 1.625122] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf009e442 [ 1.633178] Internal error: : 1008 [#1] ARM [ 1.637573] Modules linked in: [ 1.640777] CPU: 0 PID: 1 Comm: swapper Not tainted 3.12.0-rc1-n9xx-los.git-5318619-00006-g4baa700-dirty #26 [ 1.651123] task: ef04c000 ti: ef050000 task.ti: ef050000 [ 1.656799] PC is at gpmc_onenand_setup+0x98/0x1e0 [ 1.661865] LR is at gpmc_cs_set_timings+0x494/0x5a4 [ 1.667083] pc : [] lr : [] psr: 60000113 [ 1.667083] sp : ef051d10 ip : ef051ce0 fp : ef051d94 [ 1.679138] r10: c0caaf60 r9 : ef050000 r8 : ef18b32c [ 1.684631] r7 : f0080000 r6 : c0caaf60 r5 : 00000000 r4 : f009e400 [ 1.691497] r3 : f009e442 r2 : 80050000 r1 : 00000014 r0 : 00000000 [ 1.698333] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel [ 1.706024] Control: 10c5387d Table: af290019 DAC: 00000015 [ 1.712066] Process swapper (pid: 1, stack limit = 0xef050240) [ 1.718200] Stack: (0xef051d10 to 0xef052000) [ 1.722778] 1d00: 00004000 00001402 00000000 00000005 [ 1.731384] 1d20: 00000047 00000000 0000000f 0000000f 00000000 00000028 0000000f 00000005 [ 1.739990] 1d40: 00000000 00000000 00000014 00000014 00000000 00000000 00000000 00000000 [ 1.748596] 1d60: 00000000 00000019 00000000 00000000 ef18b000 ef099c50 c0c8cb30 00000000 [ 1.757171] 1d80: c0488074 c048f868 ef051dcc ef051d98 c024447c c002dfb4 00000000 c048f868 [ 1.765777] 1da0: 00000000 00000000 c010e4a4 c0dbbb7c c0c8cb40 00000000 c0ca2500 c0488074 [ 1.774383] 1dc0: ef051ddc ef051dd0 c01fd508 c0244370 ef051dfc ef051de0 c01fc204 c01fd4f4 [ 1.782989] 1de0: c0c8cb40 c0ca2500 c0c8cb74 00000000 ef051e1c ef051e00 c01fc3b0 c01fc104 [ 1.791595] 1e00: ef0983bc 00000000 c0ca2500 c01fc31c ef051e44 ef051e20 c01fa794 c01fc328 [ 1.800201] 1e20: ef03634c ef0983b0 ef27d534 c0ca2500 ef27d500 c0c9a2f8 ef051e54 ef051e48 [ 1.808807] 1e40: c01fbcfc c01fa744 ef051e84 ef051e58 c01fb838 c01fbce4 c0411df8 c0caa040 [ 1.817413] 1e60: ef051e84 c0ca2500 00000006 c0caa040 00000066 c0488074 ef051e9c ef051e88 [ 1.825988] 1e80: c01fca30 c01fb768 c04975b8 00000006 ef051eac ef051ea0 c01fd728 c01fc9bc [ 1.834594] 1ea0: ef051ebc ef051eb0 c048808c c01fd6e4 ef051f4c ef051ec0 c0008888 c0488080 [ 1.843200] 1ec0: 0000006f c046bae8 00000000 00000000 ef051efc ef051ee0 ef051f04 ef051ee8 [ 1.851806] 1ee0: c046d400 c0181218 c046d410 c18da8d5 c036a8e4 00000066 ef051f4c ef051f08 [ 1.860412] 1f00: c004b9a8 c046d41c c048f840 00000006 00000006 c046b488 00000000 c043ec08 [ 1.869018] 1f20: ef051f4c c04975b8 00000006 c0caa040 00000066 c046d410 c048f85c c048f868 [ 1.877593] 1f40: ef051f94 ef051f50 c046db8c c00087a0 00000006 00000006 c046d410 ffffffff [ 1.886199] 1f60: ffffffff ffffffff ffffffff 00000000 c0348fd0 00000000 00000000 00000000 [ 1.894805] 1f80: 00000000 00000000 ef051fac ef051f98 c0348fe0 c046daa8 00000000 00000000 [ 1.903411] 1fa0: 00000000 ef051fb0 c000e7f8 c0348fdc 00000000 00000000 00000000 00000000 [ 1.912017] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.920623] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff [ 1.929199] Backtrace: [ 1.931793] [] (gpmc_onenand_setup+0x0/0x1e0) from [] (omap2_onenand_probe+0x118/0x49c) [ 1.942047] [] (omap2_onenand_probe+0x0/0x49c) from [] (platform_drv_probe+0x20/0x24) [ 1.952117] r8:c0488074 r7:c0ca2500 r6:00000000 r5:c0c8cb40 r4:c0dbbb7c [ 1.959197] [] (platform_drv_probe+0x0/0x24) from [] (driver_probe_device+0x10c/0x224) [ 1.969360] [] (driver_probe_device+0x0/0x224) from [] (__driver_attach+0x94/0x98) [ 1.979125] r7:00000000 r6:c0c8cb74 r5:c0ca2500 r4:c0c8cb40 [ 1.985107] [] (__driver_attach+0x0/0x98) from [] (bus_for_each_dev+0x5c/0x90) [ 1.994506] r6:c01fc31c r5:c0ca2500 r4:00000000 r3:ef0983bc [ 2.000488] [] (bus_for_each_dev+0x0/0x90) from [] (driver_attach+0x24/0x28) [ 2.009735] r6:c0c9a2f8 r5:ef27d500 r4:c0ca2500 [ 2.014587] [] (driver_attach+0x0/0x28) from [] (bus_add_driver+0xdc/0x260) [ 2.023742] [] (bus_add_driver+0x0/0x260) from [] (driver_register+0x80/0xfc) [ 2.033081] r8:c0488074 r7:00000066 r6:c0caa040 r5:00000006 r4:c0ca2500 [ 2.040161] [] (driver_register+0x0/0xfc) from [] (__platform_driver_register+0x50/0x64) [ 2.050476] r5:00000006 r4:c04975b8 [ 2.054260] [] (__platform_driver_register+0x0/0x64) from [] (omap2_onenand_driver_init+0x18/0x20) [ 2.065490] [] (omap2_onenand_driver_init+0x0/0x20) from [] (do_one_initcall+0xf4/0x150) [ 2.075836] [] (do_one_initcall+0x0/0x150) from [] (kernel_init_freeable+0xf0/0x1b4) [ 2.085815] [] (kernel_init_freeable+0x0/0x1b4) from [] (kernel_init+0x10/0xec) [ 2.095336] [] (kernel_init+0x0/0xec) from [] (ret_from_fork+0x14/0x3c) [ 2.104125] r4:00000000 r3:00000000 [ 2.107879] Code: ebffc3ae e2505000 ba00002e e2843042 (e1d320b0) [ 2.114318] ---[ end trace b8ee3e3e5e002451 ]--- Signed-off-by: Aaro Koskinen Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/gpmc-onenand.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-omap2/gpmc-onenand.c b/arch/arm/mach-omap2/gpmc-onenand.c index 64b5a83..8b6876c 100644 --- a/arch/arm/mach-omap2/gpmc-onenand.c +++ b/arch/arm/mach-omap2/gpmc-onenand.c @@ -272,9 +272,19 @@ static int omap2_onenand_setup_async(void __iomem *onenand_base) struct gpmc_timings t; int ret; - if (gpmc_onenand_data->of_node) + if (gpmc_onenand_data->of_node) { gpmc_read_settings_dt(gpmc_onenand_data->of_node, &onenand_async); + if (onenand_async.sync_read || onenand_async.sync_write) { + if (onenand_async.sync_write) + gpmc_onenand_data->flags |= + ONENAND_SYNC_READWRITE; + else + gpmc_onenand_data->flags |= ONENAND_SYNC_READ; + onenand_async.sync_read = false; + onenand_async.sync_write = false; + } + } omap2_onenand_set_async_mode(onenand_base); -- cgit v1.1 From 0dbc6078c06bc002bfacf95f33960b1901c663f5 Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Thu, 3 Oct 2013 11:59:14 +0200 Subject: x86, build, pci: Fix PCI_MSI build on !SMP Commit ebd97be635 ('PCI: remove ARCH_SUPPORTS_MSI kconfig option') removed the ARCH_SUPPORTS_MSI option which architectures could select to indicate that they support MSI. Now, all architectures are supposed to build fine when MSI support is enabled: instead of having the architecture tell *when* MSI support can be used, it's up to the architecture code to ensure that MSI support can be enabled. On x86, commit ebd97be635 removed the following line: select ARCH_SUPPORTS_MSI if (X86_LOCAL_APIC && X86_IO_APIC) Which meant that MSI support was only available when the local APIC and I/O APIC were enabled. While this is always true on SMP or x86-64, it is not necessarily the case on i386 !SMP. The below patch makes sure that the local APIC and I/O APIC support is always enabled when MSI support is enabled. To do so, it: * Ensures the X86_UP_APIC option is not visible when PCI_MSI is enabled. This is the option that allows, on UP machines, to enable or not the APIC support. It is already not visible on SMP systems, or x86-64 systems, for example. We're simply also making it invisible on i386 MSI systems. * Ensures that the X86_LOCAL_APIC and X86_IO_APIC options are 'y' when PCI_MSI is enabled. Notice that this change requires a change in drivers/iommu/Kconfig to avoid a recursive Kconfig dependencey. The AMD_IOMMU option selects PCI_MSI, but was depending on X86_IO_APIC. This dependency is no longer needed: as soon as PCI_MSI is selected, the presence of X86_IO_APIC is guaranteed. Moreover, the AMD_IOMMU already depended on X86_64, which already guaranteed that X86_IO_APIC was enabled, so this dependency was anyway redundant. Signed-off-by: Thomas Petazzoni Link: http://lkml.kernel.org/r/1380794354-9079-1-git-send-email-thomas.petazzoni@free-electrons.com Reported-by: Konrad Rzeszutek Wilk Acked-by: Bjorn Helgaas Signed-off-by: H. Peter Anvin --- arch/x86/Kconfig | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index ee2fb9d..145d703 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -860,7 +860,7 @@ source "kernel/Kconfig.preempt" config X86_UP_APIC bool "Local APIC support on uniprocessors" - depends on X86_32 && !SMP && !X86_32_NON_STANDARD + depends on X86_32 && !SMP && !X86_32_NON_STANDARD && !PCI_MSI ---help--- A local APIC (Advanced Programmable Interrupt Controller) is an integrated interrupt controller in the CPU. If you have a single-CPU @@ -885,11 +885,11 @@ config X86_UP_IOAPIC config X86_LOCAL_APIC def_bool y - depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_APIC + depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_APIC || PCI_MSI config X86_IO_APIC def_bool y - depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_IOAPIC + depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_IOAPIC || PCI_MSI config X86_VISWS_APIC def_bool y -- cgit v1.1 From 8412da757776727796e9edd64ba94814cc08d536 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Ville=20Syrj=C3=A4l=C3=A4?= Date: Fri, 4 Oct 2013 15:16:04 +0300 Subject: x86/reboot: Add reboot quirk for Dell Latitude E5410 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Dell Latitude E5410 needs reboot=pci to actually reboot. Signed-off-by: Ville Syrjälä Link: http://lkml.kernel.org/r/1380888964-14517-1-git-send-email-ville.syrjala@linux.intel.com Signed-off-by: Ingo Molnar --- arch/x86/kernel/reboot.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'arch') diff --git a/arch/x86/kernel/reboot.c b/arch/x86/kernel/reboot.c index e643e74..7e920bf 100644 --- a/arch/x86/kernel/reboot.c +++ b/arch/x86/kernel/reboot.c @@ -326,6 +326,14 @@ static struct dmi_system_id __initdata reboot_dmi_table[] = { DMI_MATCH(DMI_PRODUCT_NAME, "Latitude E6320"), }, }, + { /* Handle problems with rebooting on the Latitude E5410. */ + .callback = set_pci_reboot, + .ident = "Dell Latitude E5410", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."), + DMI_MATCH(DMI_PRODUCT_NAME, "Latitude E5410"), + }, + }, { /* Handle problems with rebooting on the Latitude E5420. */ .callback = set_pci_reboot, .ident = "Dell Latitude E5420", -- cgit v1.1 From 8b3c569a3999a8fd5a819f892525ab5520777c92 Mon Sep 17 00:00:00 2001 From: James Hogan Date: Mon, 7 Oct 2013 12:14:26 +0100 Subject: MIPS: stack protector: Fix per-task canary switch Commit 1400eb6 (MIPS: r4k,octeon,r2300: stack protector: change canary per task) was merged in v3.11 and introduced assembly in the MIPS resume functions to update the value of the current canary in __stack_chk_guard. However it used PTR_L resulting in a load of the canary value, instead of PTR_LA to construct its address. The value is intended to be random but is then treated as an address in the subsequent LONG_S (store). This was observed to cause a fault and panic: CPU 0 Unable to handle kernel paging request at virtual address 139fea20, epc == 8000cc0c, ra == 8034f2a4 Oops[#1]: ... $24 : 139fea20 1e1f7cb6 ... Call Trace: [<8000cc0c>] resume+0xac/0x118 [<8034f2a4>] __schedule+0x5f8/0x78c [<8034f4e0>] schedule_preempt_disabled+0x20/0x2c [<80348eec>] rest_init+0x74/0x84 [<804dc990>] start_kernel+0x43c/0x454 Code: 3c18804b 8f184030 8cb901f8 00c0e021 8cb002f0 8cb102f4 8cb202f8 8cb302fc This can also be forced by modifying arch/mips/include/asm/stackprotector.h so that the default __stack_chk_guard value is more likely to be a bad (or unaligned) pointer. Fix it to use PTR_LA instead, to load the address of the canary value, which the LONG_S can then use to write into it. Reported-by: bobjones (via #mipslinux on IRC) Signed-off-by: James Hogan Cc: Ralf Baechle Cc: Gregory Fong Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/6026/ Signed-off-by: Ralf Baechle --- arch/mips/kernel/octeon_switch.S | 2 +- arch/mips/kernel/r2300_switch.S | 2 +- arch/mips/kernel/r4k_switch.S | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/mips/kernel/octeon_switch.S b/arch/mips/kernel/octeon_switch.S index 4204d76..029e002 100644 --- a/arch/mips/kernel/octeon_switch.S +++ b/arch/mips/kernel/octeon_switch.S @@ -73,7 +73,7 @@ 3: #if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP) - PTR_L t8, __stack_chk_guard + PTR_LA t8, __stack_chk_guard LONG_L t9, TASK_STACK_CANARY(a1) LONG_S t9, 0(t8) #endif diff --git a/arch/mips/kernel/r2300_switch.S b/arch/mips/kernel/r2300_switch.S index 38af83f..20b7b04 100644 --- a/arch/mips/kernel/r2300_switch.S +++ b/arch/mips/kernel/r2300_switch.S @@ -67,7 +67,7 @@ LEAF(resume) 1: #if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP) - PTR_L t8, __stack_chk_guard + PTR_LA t8, __stack_chk_guard LONG_L t9, TASK_STACK_CANARY(a1) LONG_S t9, 0(t8) #endif diff --git a/arch/mips/kernel/r4k_switch.S b/arch/mips/kernel/r4k_switch.S index 921238a..078de5ea 100644 --- a/arch/mips/kernel/r4k_switch.S +++ b/arch/mips/kernel/r4k_switch.S @@ -69,7 +69,7 @@ 1: #if defined(CONFIG_CC_STACKPROTECTOR) && !defined(CONFIG_SMP) - PTR_L t8, __stack_chk_guard + PTR_LA t8, __stack_chk_guard LONG_L t9, TASK_STACK_CANARY(a1) LONG_S t9, 0(t8) #endif -- cgit v1.1 From d45ed4a4e33ae103053c0a53d280014e7101bb5c Mon Sep 17 00:00:00 2001 From: Alexei Starovoitov Date: Fri, 4 Oct 2013 00:14:06 -0700 Subject: net: fix unsafe set_memory_rw from softirq on x86 system with net.core.bpf_jit_enable = 1 sudo tcpdump -i eth1 'tcp port 22' causes the warning: [ 56.766097] Possible unsafe locking scenario: [ 56.766097] [ 56.780146] CPU0 [ 56.786807] ---- [ 56.793188] lock(&(&vb->lock)->rlock); [ 56.799593] [ 56.805889] lock(&(&vb->lock)->rlock); [ 56.812266] [ 56.812266] *** DEADLOCK *** [ 56.812266] [ 56.830670] 1 lock held by ksoftirqd/1/13: [ 56.836838] #0: (rcu_read_lock){.+.+..}, at: [] vm_unmap_aliases+0x8c/0x380 [ 56.849757] [ 56.849757] stack backtrace: [ 56.862194] CPU: 1 PID: 13 Comm: ksoftirqd/1 Not tainted 3.12.0-rc3+ #45 [ 56.868721] Hardware name: System manufacturer System Product Name/P8Z77 WS, BIOS 3007 07/26/2012 [ 56.882004] ffffffff821944c0 ffff88080bbdb8c8 ffffffff8175a145 0000000000000007 [ 56.895630] ffff88080bbd5f40 ffff88080bbdb928 ffffffff81755b14 0000000000000001 [ 56.909313] ffff880800000001 ffff880800000000 ffffffff8101178f 0000000000000001 [ 56.923006] Call Trace: [ 56.929532] [] dump_stack+0x55/0x76 [ 56.936067] [] print_usage_bug+0x1f7/0x208 [ 56.942445] [] ? save_stack_trace+0x2f/0x50 [ 56.948932] [] ? check_usage_backwards+0x150/0x150 [ 56.955470] [] mark_lock+0x282/0x2c0 [ 56.961945] [] __lock_acquire+0x45d/0x1d50 [ 56.968474] [] ? __lock_acquire+0x2de/0x1d50 [ 56.975140] [] ? cpumask_next_and+0x55/0x90 [ 56.981942] [] lock_acquire+0x92/0x1d0 [ 56.988745] [] ? vm_unmap_aliases+0x16a/0x380 [ 56.995619] [] _raw_spin_lock+0x41/0x50 [ 57.002493] [] ? vm_unmap_aliases+0x16a/0x380 [ 57.009447] [] vm_unmap_aliases+0x16a/0x380 [ 57.016477] [] ? vm_unmap_aliases+0x8c/0x380 [ 57.023607] [] change_page_attr_set_clr+0xc0/0x460 [ 57.030818] [] ? trace_hardirqs_on+0xd/0x10 [ 57.037896] [] ? kmem_cache_free+0xb0/0x2b0 [ 57.044789] [] ? free_object_rcu+0x93/0xa0 [ 57.051720] [] set_memory_rw+0x2f/0x40 [ 57.058727] [] bpf_jit_free+0x2c/0x40 [ 57.065577] [] sk_filter_release_rcu+0x1a/0x30 [ 57.072338] [] rcu_process_callbacks+0x202/0x7c0 [ 57.078962] [] __do_softirq+0xf7/0x3f0 [ 57.085373] [] run_ksoftirqd+0x35/0x70 cannot reuse jited filter memory, since it's readonly, so use original bpf insns memory to hold work_struct defer kfree of sk_filter until jit completed freeing tested on x86_64 and i386 Signed-off-by: Alexei Starovoitov Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- arch/arm/net/bpf_jit_32.c | 1 + arch/powerpc/net/bpf_jit_comp.c | 1 + arch/s390/net/bpf_jit_comp.c | 4 +++- arch/sparc/net/bpf_jit_comp.c | 1 + arch/x86/net/bpf_jit_comp.c | 18 +++++++++++++----- 5 files changed, 19 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/arm/net/bpf_jit_32.c b/arch/arm/net/bpf_jit_32.c index f50d223..99b44e0 100644 --- a/arch/arm/net/bpf_jit_32.c +++ b/arch/arm/net/bpf_jit_32.c @@ -930,4 +930,5 @@ void bpf_jit_free(struct sk_filter *fp) { if (fp->bpf_func != sk_run_filter) module_free(NULL, fp->bpf_func); + kfree(fp); } diff --git a/arch/powerpc/net/bpf_jit_comp.c b/arch/powerpc/net/bpf_jit_comp.c index bf56e33..2345bdb 100644 --- a/arch/powerpc/net/bpf_jit_comp.c +++ b/arch/powerpc/net/bpf_jit_comp.c @@ -691,4 +691,5 @@ void bpf_jit_free(struct sk_filter *fp) { if (fp->bpf_func != sk_run_filter) module_free(NULL, fp->bpf_func); + kfree(fp); } diff --git a/arch/s390/net/bpf_jit_comp.c b/arch/s390/net/bpf_jit_comp.c index 7092392..a5df511 100644 --- a/arch/s390/net/bpf_jit_comp.c +++ b/arch/s390/net/bpf_jit_comp.c @@ -881,7 +881,9 @@ void bpf_jit_free(struct sk_filter *fp) struct bpf_binary_header *header = (void *)addr; if (fp->bpf_func == sk_run_filter) - return; + goto free_filter; set_memory_rw(addr, header->pages); module_free(NULL, header); +free_filter: + kfree(fp); } diff --git a/arch/sparc/net/bpf_jit_comp.c b/arch/sparc/net/bpf_jit_comp.c index 9c7be59e..218b6b2 100644 --- a/arch/sparc/net/bpf_jit_comp.c +++ b/arch/sparc/net/bpf_jit_comp.c @@ -808,4 +808,5 @@ void bpf_jit_free(struct sk_filter *fp) { if (fp->bpf_func != sk_run_filter) module_free(NULL, fp->bpf_func); + kfree(fp); } diff --git a/arch/x86/net/bpf_jit_comp.c b/arch/x86/net/bpf_jit_comp.c index 79c216a..516593e1 100644 --- a/arch/x86/net/bpf_jit_comp.c +++ b/arch/x86/net/bpf_jit_comp.c @@ -772,13 +772,21 @@ out: return; } +static void bpf_jit_free_deferred(struct work_struct *work) +{ + struct sk_filter *fp = container_of(work, struct sk_filter, work); + unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK; + struct bpf_binary_header *header = (void *)addr; + + set_memory_rw(addr, header->pages); + module_free(NULL, header); + kfree(fp); +} + void bpf_jit_free(struct sk_filter *fp) { if (fp->bpf_func != sk_run_filter) { - unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK; - struct bpf_binary_header *header = (void *)addr; - - set_memory_rw(addr, header->pages); - module_free(NULL, header); + INIT_WORK(&fp->work, bpf_jit_free_deferred); + schedule_work(&fp->work); } } -- cgit v1.1 From 016c12d2fb8584db392211bc6b0bdd6fcf7cfd97 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Mon, 7 Oct 2013 15:43:49 -0500 Subject: ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree SoC family definitions at the moment are reactive to board needs as a result, beagle-xm would matchup with ti,omap3 which invokes omap3430_init_early instead of omap3630_init_early. Obviously, this is the wrong behavior. With clock node dts conversion, we get the following warnings before system hangs as a result and 3630 based platforms fails to boot (uart4 clocks are only present in OMAP3630 and not present in OMAP3430): ... omap_hwmod: uart4: cannot clk_get main_clk uart4_fck omap_hwmod: uart4: cannot _init_clocks WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434 _init+0x6c/0x80() omap_hwmod: uart4: couldn't init clocks ... WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126 _enable+0x254/0x280() omap_hwmod: timer12: enabled state can only be entered from initialized, idle, or disabled state ... WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224 _idle+0xd4/0xf8() omap_hwmod: timer12: idle state can only be entered from enabled state WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126 _enable+0x254/0x280() omap_hwmod: uart4: enabled state can only be entered from initialized, idle, or disabled state So, add specific compatiblity for 3630 to allow match for Beagle-XM platform. Signed-off-by: Nishanth Menon [tony@atomide.com: left out ti,omap343x, updated comments] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-beagle-xm.dts | 2 +- arch/arm/mach-omap2/board-generic.c | 18 ++++++++++++++++++ 2 files changed, 19 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 0c514dc..2816bf6 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -11,7 +11,7 @@ / { model = "TI OMAP3 BeagleBoard xM"; - compatible = "ti,omap3-beagle-xm", "ti,omap3-beagle", "ti,omap3"; + compatible = "ti,omap3-beagle-xm", "ti,omap36xx", "ti,omap3"; cpus { cpu@0 { diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 39c7838..87162e1 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -129,6 +129,24 @@ DT_MACHINE_START(OMAP3_DT, "Generic OMAP3 (Flattened Device Tree)") .restart = omap3xxx_restart, MACHINE_END +static const char *omap36xx_boards_compat[] __initdata = { + "ti,omap36xx", + NULL, +}; + +DT_MACHINE_START(OMAP36XX_DT, "Generic OMAP36xx (Flattened Device Tree)") + .reserve = omap_reserve, + .map_io = omap3_map_io, + .init_early = omap3630_init_early, + .init_irq = omap_intc_of_init, + .handle_irq = omap3_intc_handle_irq, + .init_machine = omap_generic_init, + .init_late = omap3_init_late, + .init_time = omap3_sync32k_timer_init, + .dt_compat = omap36xx_boards_compat, + .restart = omap3xxx_restart, +MACHINE_END + static const char *omap3_gp_boards_compat[] __initdata = { "ti,omap3-beagle", "timll,omap3-devkit8000", -- cgit v1.1 From d623a0e19dcbc4e44a8db047158815d7f8c2b839 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 7 Oct 2013 10:22:01 -0700 Subject: ARM: dts: Fix pinctrl mask for omap3 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The wake-up interrupt bit is available on omap3/4/5 processors unlike what we claim. Without fixing it we cannot use it on omap3 and the system configured for wake-up events will just hang on wake-up. Cc: Grygorii Strashko Cc: Benoît Cousson Cc: devicetree@vger.kernel.org Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3.dtsi | 4 ++-- arch/arm/mach-omap2/mux.h | 4 +--- 2 files changed, 3 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index 7d95cda..b41bd57 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -108,7 +108,7 @@ #address-cells = <1>; #size-cells = <0>; pinctrl-single,register-width = <16>; - pinctrl-single,function-mask = <0x7f1f>; + pinctrl-single,function-mask = <0xff1f>; }; omap3_pmx_wkup: pinmux@0x48002a00 { @@ -117,7 +117,7 @@ #address-cells = <1>; #size-cells = <0>; pinctrl-single,register-width = <16>; - pinctrl-single,function-mask = <0x7f1f>; + pinctrl-single,function-mask = <0xff1f>; }; gpio1: gpio@48310000 { diff --git a/arch/arm/mach-omap2/mux.h b/arch/arm/mach-omap2/mux.h index 5d2080e..16f78a9 100644 --- a/arch/arm/mach-omap2/mux.h +++ b/arch/arm/mach-omap2/mux.h @@ -28,7 +28,7 @@ #define OMAP_PULL_UP (1 << 4) #define OMAP_ALTELECTRICALSEL (1 << 5) -/* 34xx specific mux bit defines */ +/* omap3/4/5 specific mux bit defines */ #define OMAP_INPUT_EN (1 << 8) #define OMAP_OFF_EN (1 << 9) #define OMAP_OFFOUT_EN (1 << 10) @@ -36,8 +36,6 @@ #define OMAP_OFF_PULL_EN (1 << 12) #define OMAP_OFF_PULL_UP (1 << 13) #define OMAP_WAKEUP_EN (1 << 14) - -/* 44xx specific mux bit defines */ #define OMAP_WAKEUP_EVENT (1 << 15) /* Active pin states */ -- cgit v1.1 From 0b8214fe186746d32d8ca5522b736d5b59fd5d40 Mon Sep 17 00:00:00 2001 From: Simon Barth Date: Tue, 8 Oct 2013 10:50:33 +0200 Subject: ARM: mach-omap2: board-generic: fix undefined symbol Since dra7 reuses the function 'omap5_realtime_timer_init' in arch/arm/mach-omap2/board-generic.c as timer init function, it has to be built for this SoC as well. Signed-off-by: Simon Barth Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/timer.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c index fa74a06..ead48fa 100644 --- a/arch/arm/mach-omap2/timer.c +++ b/arch/arm/mach-omap2/timer.c @@ -628,7 +628,7 @@ void __init omap4_local_timer_init(void) #endif /* CONFIG_HAVE_ARM_TWD */ #endif /* CONFIG_ARCH_OMAP4 */ -#ifdef CONFIG_SOC_OMAP5 +#if defined(CONFIG_SOC_OMAP5) || defined(CONFIG_SOC_DRA7XX) void __init omap5_realtime_timer_init(void) { omap4_sync32k_timer_init(); @@ -636,7 +636,7 @@ void __init omap5_realtime_timer_init(void) clocksource_of_init(); } -#endif /* CONFIG_SOC_OMAP5 */ +#endif /* CONFIG_SOC_OMAP5 || CONFIG_SOC_DRA7XX */ /** * omap_timer_init - build and register timer device with an -- cgit v1.1 From d1f1ca36b566aa56effdd7df69750062ec735131 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Pali=20Roh=C3=A1r?= Date: Mon, 23 Sep 2013 14:50:12 +0200 Subject: ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit File drivers/leds/leds-lp55xx-common.c refuse to change led_current sysfs attribute if value is higher than max_current specified in board file. By default global C variables are zero, so changing always failed. This patch adding missing max_current and setting it to max safe value 100 (10 mA). It is unclear which commit exactly caused this regression as the lp5523 driver was broken and was hiding the platform data breakage. Now the driver is fixed so this should be fixed as well. Signed-off-by: Pali Rohár Signed-off-by: Joerg Reisenweber [tony@atomide.com: updated comments to describe regression] Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-rx51-peripherals.c | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index c3270c0..f6fe388 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -167,38 +167,47 @@ static struct lp55xx_led_config rx51_lp5523_led_config[] = { .name = "lp5523:kb1", .chan_nr = 0, .led_current = 50, + .max_current = 100, }, { .name = "lp5523:kb2", .chan_nr = 1, .led_current = 50, + .max_current = 100, }, { .name = "lp5523:kb3", .chan_nr = 2, .led_current = 50, + .max_current = 100, }, { .name = "lp5523:kb4", .chan_nr = 3, .led_current = 50, + .max_current = 100, }, { .name = "lp5523:b", .chan_nr = 4, .led_current = 50, + .max_current = 100, }, { .name = "lp5523:g", .chan_nr = 5, .led_current = 50, + .max_current = 100, }, { .name = "lp5523:r", .chan_nr = 6, .led_current = 50, + .max_current = 100, }, { .name = "lp5523:kb5", .chan_nr = 7, .led_current = 50, + .max_current = 100, }, { .name = "lp5523:kb6", .chan_nr = 8, .led_current = 50, + .max_current = 100, } }; -- cgit v1.1 From 7cde9b27e7b3a2e09d647bb4f6d94e842698d2d5 Mon Sep 17 00:00:00 2001 From: Frediano Ziglio Date: Thu, 10 Oct 2013 14:39:37 +0000 Subject: xen: Fix possible user space selector corruption Due to the way kernel is initialized under Xen is possible that the ring1 selector used by the kernel for the boot cpu end up to be copied to userspace leading to segmentation fault in the userspace. Xen code in the kernel initialize no-boot cpus with correct selectors (ds and es set to __USER_DS) but the boot one keep the ring1 (passed by Xen). On task context switch (switch_to) we assume that ds, es and cs already point to __USER_DS and __KERNEL_CSso these selector are not changed. If processor is an Intel that support sysenter instruction sysenter/sysexit is used so ds and es are not restored switching back from kernel to userspace. In the case the selectors point to a ring1 instead of __USER_DS the userspace code will crash on first memory access attempt (to be precise Xen on the emulated iret used to do sysexit will detect and set ds and es to zero which lead to GPF anyway). Now if an userspace process call kernel using sysenter and get rescheduled (for me it happen on a specific init calling wait4) could happen that the ring1 selector is set to ds and es. This is quite hard to detect cause after a while these selectors are fixed (__USER_DS seems sticky). Bisecting the code commit 7076aada1040de4ed79a5977dbabdb5e5ea5e249 appears to be the first one that have this issue. Signed-off-by: Frediano Ziglio Signed-off-by: Stefano Stabellini Reviewed-by: Andrew Cooper --- arch/x86/xen/smp.c | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'arch') diff --git a/arch/x86/xen/smp.c b/arch/x86/xen/smp.c index d1e4777..31d0475 100644 --- a/arch/x86/xen/smp.c +++ b/arch/x86/xen/smp.c @@ -278,6 +278,15 @@ static void __init xen_smp_prepare_boot_cpu(void) old memory can be recycled */ make_lowmem_page_readwrite(xen_initial_gdt); +#ifdef CONFIG_X86_32 + /* + * Xen starts us with XEN_FLAT_RING1_DS, but linux code + * expects __USER_DS + */ + loadsegment(ds, __USER_DS); + loadsegment(es, __USER_DS); +#endif + xen_filter_cpu_maps(); xen_setup_vcpu_info_placement(); } -- cgit v1.1 From 5b24282846c064ee90d40fcb3a8f63b8e754fd28 Mon Sep 17 00:00:00 2001 From: Vineet Gupta Date: Thu, 10 Oct 2013 19:33:57 +0530 Subject: ARC: Ignore ptrace SETREGSET request for synthetic register "stop_pc" ARCompact TRAP_S insn used for breakpoints, commits before exception is taken (updating architectural PC). So ptregs->ret contains next-PC and not the breakpoint PC itself. This is different from other restartable exceptions such as TLB Miss where ptregs->ret has exact faulting PC. gdb needs to know exact-PC hence ARC ptrace GETREGSET provides for @stop_pc which returns ptregs->ret vs. EFA depending on the situation. However, writing stop_pc (SETREGSET request), which updates ptregs->ret doesn't makes sense stop_pc doesn't always correspond to that reg as described above. This was not an issue so far since user_regs->ret / user_regs->stop_pc had same value and both writing to ptregs->ret was OK, needless, but NOT broken, hence not observed. With gdb "jump", they diverge, and user_regs->ret updating ptregs is overwritten immediately with stop_pc, which this patch fixes. Reported-by: Anton Kolesov Signed-off-by: Vineet Gupta --- arch/arc/kernel/ptrace.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arc/kernel/ptrace.c b/arch/arc/kernel/ptrace.c index 3332385..5d76706 100644 --- a/arch/arc/kernel/ptrace.c +++ b/arch/arc/kernel/ptrace.c @@ -102,7 +102,7 @@ static int genregs_set(struct task_struct *target, REG_IGNORE_ONE(pad2); REG_IN_CHUNK(callee, efa, cregs); /* callee_regs[r25..r13] */ REG_IGNORE_ONE(efa); /* efa update invalid */ - REG_IN_ONE(stop_pc, &ptregs->ret); /* stop_pc: PC update */ + REG_IGNORE_ONE(stop_pc); /* PC updated via @ret */ return ret; } -- cgit v1.1 From 320c90be7ba1c371e882edff57272a89b213d136 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 5 Sep 2013 11:33:15 +0200 Subject: parisc: Export flush_cache_page() (needed by lustre) ERROR: "flush_cache_page" [drivers/staging/lustre/lustre/libcfs/libcfs.ko] undefined! Signed-off-by: Geert Uytterhoeven Signed-off-by: Helge Deller --- arch/parisc/kernel/cache.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/parisc/kernel/cache.c b/arch/parisc/kernel/cache.c index c035673..b521c0a 100644 --- a/arch/parisc/kernel/cache.c +++ b/arch/parisc/kernel/cache.c @@ -602,6 +602,7 @@ flush_cache_page(struct vm_area_struct *vma, unsigned long vmaddr, unsigned long __flush_cache_page(vma, vmaddr, PFN_PHYS(pfn)); } } +EXPORT_SYMBOL_GPL(flush_cache_page); #ifdef CONFIG_PARISC_TMPALIAS -- cgit v1.1 From 528d8eb20a3053d72cb0cea486418aa602d9e1f1 Mon Sep 17 00:00:00 2001 From: Jiang Liu Date: Thu, 12 Sep 2013 00:07:18 +0800 Subject: parisc: kill SMP single function call interrupt Commit 9a46ad6d6df3b54 "smp: make smp_call_function_many() use logic similar to smp_call_function_single()" has unified the way to handle single and multiple cross-CPU function calls. Now only one interrupt is needed for architecture specific code to support generic SMP function call interfaces, so kill the redundant single function call interrupt. Signed-off-by: Jiang Liu Cc: Jiang Liu Signed-off-by: Helge Deller --- arch/parisc/kernel/smp.c | 8 +------- 1 file changed, 1 insertion(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/parisc/kernel/smp.c b/arch/parisc/kernel/smp.c index 8a252f2..2b96602 100644 --- a/arch/parisc/kernel/smp.c +++ b/arch/parisc/kernel/smp.c @@ -72,7 +72,6 @@ enum ipi_message_type { IPI_NOP=0, IPI_RESCHEDULE=1, IPI_CALL_FUNC, - IPI_CALL_FUNC_SINGLE, IPI_CPU_START, IPI_CPU_STOP, IPI_CPU_TEST @@ -164,11 +163,6 @@ ipi_interrupt(int irq, void *dev_id) generic_smp_call_function_interrupt(); break; - case IPI_CALL_FUNC_SINGLE: - smp_debug(100, KERN_DEBUG "CPU%d IPI_CALL_FUNC_SINGLE\n", this_cpu); - generic_smp_call_function_single_interrupt(); - break; - case IPI_CPU_START: smp_debug(100, KERN_DEBUG "CPU%d IPI_CPU_START\n", this_cpu); break; @@ -260,7 +254,7 @@ void arch_send_call_function_ipi_mask(const struct cpumask *mask) void arch_send_call_function_single_ipi(int cpu) { - send_IPI_single(cpu, IPI_CALL_FUNC_SINGLE); + send_IPI_single(cpu, IPI_CALL_FUNC); } /* -- cgit v1.1 From ec7c241953d14af097d941de56348c55e4e9ac5d Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Wed, 9 Oct 2013 23:10:14 +0200 Subject: parisc: remove unused syscall_ipi() function. Signed-off-by: Helge Deller --- arch/parisc/kernel/traps.c | 5 ----- 1 file changed, 5 deletions(-) (limited to 'arch') diff --git a/arch/parisc/kernel/traps.c b/arch/parisc/kernel/traps.c index 04e47c6..ebc877c 100644 --- a/arch/parisc/kernel/traps.c +++ b/arch/parisc/kernel/traps.c @@ -291,11 +291,6 @@ void die_if_kernel(char *str, struct pt_regs *regs, long err) do_exit(SIGSEGV); } -int syscall_ipi(int (*syscall) (struct pt_regs *), struct pt_regs *regs) -{ - return syscall(regs); -} - /* gdb uses break 4,8 */ #define GDB_BREAK_INSN 0x10004 static void handle_gdb_break(struct pt_regs *regs, int wot) -- cgit v1.1 From a60ac4b5f0b630889a01293db52ac65003a01e98 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Wed, 9 Oct 2013 23:12:46 +0200 Subject: parisc: mark parisc_terminate() noreturn and cold. Signed-off-by: Helge Deller --- arch/parisc/include/asm/traps.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/parisc/include/asm/traps.h b/arch/parisc/include/asm/traps.h index 1945f99..4736020 100644 --- a/arch/parisc/include/asm/traps.h +++ b/arch/parisc/include/asm/traps.h @@ -6,7 +6,7 @@ struct pt_regs; /* traps.c */ void parisc_terminate(char *msg, struct pt_regs *regs, - int code, unsigned long offset); + int code, unsigned long offset) __noreturn __cold; /* mm/fault.c */ void do_page_fault(struct pt_regs *regs, unsigned long code, -- cgit v1.1 From 59b33f148cc08fb33cbe823fca1e34f7f023765e Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Tue, 1 Oct 2013 21:54:46 +0200 Subject: parisc: fix interruption handler to respect pagefault_disable() Running an "echo t > /proc/sysrq-trigger" crashes the parisc kernel. The problem is, that in print_worker_info() we try to read the workqueue info via the probe_kernel_read() functions which use pagefault_disable() to avoid crashes like this: probe_kernel_read(&pwq, &worker->current_pwq, sizeof(pwq)); probe_kernel_read(&wq, &pwq->wq, sizeof(wq)); probe_kernel_read(name, wq->name, sizeof(name) - 1); The problem here is, that the first probe_kernel_read(&pwq) might return zero in pwq and as such the following probe_kernel_reads() try to access contents of the page zero which is read protected and generate a kernel segfault. With this patch we fix the interruption handler to call parisc_terminate() directly only if pagefault_disable() was not called (in which case preempt_count()==0). Otherwise we hand over to the pagefault handler which will try to look up the faulting address in the fixup tables. Signed-off-by: Helge Deller Cc: # v3.0+ Signed-off-by: John David Anglin Signed-off-by: Helge Deller --- arch/parisc/kernel/traps.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/parisc/kernel/traps.c b/arch/parisc/kernel/traps.c index ebc877c..1cd1d0c 100644 --- a/arch/parisc/kernel/traps.c +++ b/arch/parisc/kernel/traps.c @@ -800,14 +800,14 @@ void notrace handle_interruption(int code, struct pt_regs *regs) else { /* - * The kernel should never fault on its own address space. + * The kernel should never fault on its own address space, + * unless pagefault_disable() was called before. */ - if (fault_space == 0) + if (fault_space == 0 && !in_atomic()) { pdc_chassis_send_status(PDC_CHASSIS_DIRECT_PANIC); parisc_terminate("Kernel Fault", regs, code, fault_address); - } } -- cgit v1.1 From 2d8b22de6e5241a6f27f7f290f027223156a7d3f Mon Sep 17 00:00:00 2001 From: John David Anglin Date: Sat, 5 Oct 2013 10:55:36 -0400 Subject: parisc: optimize variable initialization in do_page_fault The attached change defers the initialization of the variables tsk, mm and flags until they are needed. As a result, the code won't crash if a kernel probe is done with a corrupt context and the code will be better optimized. Signed-off-by: John David Anglin Signed-off-by: Helge Deller --- arch/parisc/mm/fault.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/parisc/mm/fault.c b/arch/parisc/mm/fault.c index 00c0ed3..0293588 100644 --- a/arch/parisc/mm/fault.c +++ b/arch/parisc/mm/fault.c @@ -171,20 +171,25 @@ void do_page_fault(struct pt_regs *regs, unsigned long code, unsigned long address) { struct vm_area_struct *vma, *prev_vma; - struct task_struct *tsk = current; - struct mm_struct *mm = tsk->mm; + struct task_struct *tsk; + struct mm_struct *mm; unsigned long acc_type; int fault; - unsigned int flags = FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE; + unsigned int flags; - if (in_atomic() || !mm) + if (in_atomic()) goto no_context; + tsk = current; + mm = tsk->mm; + if (!mm) + goto no_context; + + flags = FAULT_FLAG_ALLOW_RETRY | FAULT_FLAG_KILLABLE; if (user_mode(regs)) flags |= FAULT_FLAG_USER; acc_type = parisc_acctyp(code, regs->iir); - if (acc_type & VM_WRITE) flags |= FAULT_FLAG_WRITE; retry: -- cgit v1.1 From db080f9c530f78dad661257885a1893506077068 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Wed, 9 Oct 2013 23:47:03 +0200 Subject: parisc: let probe_kernel_read() capture access to page zero Signed-off-by: Helge Deller --- arch/parisc/lib/memcpy.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/parisc/lib/memcpy.c b/arch/parisc/lib/memcpy.c index ac4370b..b5507ec 100644 --- a/arch/parisc/lib/memcpy.c +++ b/arch/parisc/lib/memcpy.c @@ -56,7 +56,7 @@ #ifdef __KERNEL__ #include #include -#include +#include #define s_space "%%sr1" #define d_space "%%sr2" #else @@ -524,4 +524,17 @@ EXPORT_SYMBOL(copy_to_user); EXPORT_SYMBOL(copy_from_user); EXPORT_SYMBOL(copy_in_user); EXPORT_SYMBOL(memcpy); + +long probe_kernel_read(void *dst, const void *src, size_t size) +{ + unsigned long addr = (unsigned long)src; + + if (size < 0 || addr < PAGE_SIZE) + return -EFAULT; + + /* check for I/O space F_EXTEND(0xfff00000) access as well? */ + + return __probe_kernel_read(dst, src, size); +} + #endif -- cgit v1.1 From 4d594dd3028ba8cdfcbd854bde3811a1ee4e36d7 Mon Sep 17 00:00:00 2001 From: Yuvaraj Kumar C D Date: Wed, 18 Sep 2013 15:41:53 +0530 Subject: ARM: exynos: dts: Update 5250 arch timer node with clock frequency Without the "clock-frequency" property in arch timer node, could able to see the below crash dump. [] (unwind_backtrace+0x0/0xf4) from [] (show_stack+0x10/0x14) [] (show_stack+0x10/0x14) from [] (dump_stack+0x7c/0xb0) [] (dump_stack+0x7c/0xb0) from [] (Ldiv0_64+0x8/0x18) [] (Ldiv0_64+0x8/0x18) from [] (clockevents_config.part.2+0x1c/0x74) [] (clockevents_config.part.2+0x1c/0x74) from [] (clockevents_config_and_register+0x20/0x2c) [] (clockevents_config_and_register+0x20/0x2c) from [] (arch_timer_setup+0xa8/0x134) [] (arch_timer_setup+0xa8/0x134) from [] (arch_timer_init+0x1f4/0x24c) [] (arch_timer_init+0x1f4/0x24c) from [] (clocksource_of_init+0x34/0x58) [] (clocksource_of_init+0x34/0x58) from [] (time_init+0x20/0x2c) [] (time_init+0x20/0x2c) from [] (start_kernel+0x1e0/0x39c) THis is because the Exynos u-boot, for example on the Chromebooks, doesn't set up the CNTFRQ register as expected by arch_timer. Instead, we have to specify the frequency in the device tree like this. Signed-off-by: Yuvaraj Kumar C D [olof: Changed subject, added comment, elaborated on commit message] Signed-off-by: Olof Johansson --- arch/arm/boot/dts/exynos5250.dtsi | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi index 7d7cc77..bbac42a 100644 --- a/arch/arm/boot/dts/exynos5250.dtsi +++ b/arch/arm/boot/dts/exynos5250.dtsi @@ -96,6 +96,11 @@ <1 14 0xf08>, <1 11 0xf08>, <1 10 0xf08>; + /* Unfortunately we need this since some versions of U-Boot + * on Exynos don't set the CNTFRQ register, so we need the + * value from DT. + */ + clock-frequency = <24000000>; }; mct@101C0000 { -- cgit v1.1 From 3c1532df5c1b54b5f6246cdef94eeb73a39fe43a Mon Sep 17 00:00:00 2001 From: AKASHI Takahiro Date: Wed, 9 Oct 2013 15:58:29 +0100 Subject: ARM: 7851/1: check for number of arguments in syscall_get/set_arguments() In ftrace_syscall_enter(), syscall_get_arguments(..., 0, n, ...) if (i == 0) { ...; n--;} memcpy(..., n * sizeof(args[0])); If 'number of arguments(n)' is zero and 'argument index(i)' is also zero in syscall_get_arguments(), none of arguments should be copied by memcpy(). Otherwise 'n--' can be a big positive number and unexpected amount of data will be copied. Tracing system calls which take no argument, say sync(void), may hit this case and eventually make the system corrupted. This patch fixes the issue both in syscall_get_arguments() and syscall_set_arguments(). Cc: Acked-by: Will Deacon Signed-off-by: AKASHI Takahiro Signed-off-by: Will Deacon Signed-off-by: Russell King --- arch/arm/include/asm/syscall.h | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch') diff --git a/arch/arm/include/asm/syscall.h b/arch/arm/include/asm/syscall.h index f1d96d4..73ddd723 100644 --- a/arch/arm/include/asm/syscall.h +++ b/arch/arm/include/asm/syscall.h @@ -57,6 +57,9 @@ static inline void syscall_get_arguments(struct task_struct *task, unsigned int i, unsigned int n, unsigned long *args) { + if (n == 0) + return; + if (i + n > SYSCALL_MAX_ARGS) { unsigned long *args_bad = args + SYSCALL_MAX_ARGS - i; unsigned int n_bad = n + i - SYSCALL_MAX_ARGS; @@ -81,6 +84,9 @@ static inline void syscall_set_arguments(struct task_struct *task, unsigned int i, unsigned int n, const unsigned long *args) { + if (n == 0) + return; + if (i + n > SYSCALL_MAX_ARGS) { pr_warning("%s called with max args %d, handling only %d\n", __func__, i + n, SYSCALL_MAX_ARGS); -- cgit v1.1 From 29114fd7db2fc82a34da8340d29b8fa413e03dca Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 7 Oct 2013 15:19:53 +0200 Subject: ARM: integrator: deactivate timer0 on the Integrator/CP This fixes a long-standing Integrator/CP regression from commit 870e2928cf3368ca9b06bc925d0027b0a56bcd8e "ARM: integrator-cp: convert use CLKSRC_OF for timer init" When this code was introduced, the both aliases pointing the system to use timer1 as primary (clocksource) and timer2 as secondary (clockevent) was ignored, and the system would simply use the first two timers found as clocksource and clockevent. However this made the system timeline accelerate by a factor x25, as it turns out that the way the clocking actually works (totally undocumented and found after some trial-and-error) is that timer0 runs @ 25MHz and timer1 and timer2 runs @ 1MHz. Presumably this divider setting is a boot-on default and configurable albeit the way to configure it is not documented. So as a quick fix to the problem, let's mark timer0 as disabled, so the code will chose timer1 and timer2 as it used to. This also deletes the two aliases for the primary and secondary timer as they have been superceded by the auto-selection Cc: stable@vger.kernel.org Cc: Rob Herring Cc: Russell King Signed-off-by: Linus Walleij Signed-off-by: Olof Johansson --- arch/arm/boot/dts/integratorcp.dts | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/integratorcp.dts b/arch/arm/boot/dts/integratorcp.dts index ff1aea0..72693a6 100644 --- a/arch/arm/boot/dts/integratorcp.dts +++ b/arch/arm/boot/dts/integratorcp.dts @@ -9,11 +9,6 @@ model = "ARM Integrator/CP"; compatible = "arm,integrator-cp"; - aliases { - arm,timer-primary = &timer2; - arm,timer-secondary = &timer1; - }; - chosen { bootargs = "root=/dev/ram0 console=ttyAMA0,38400n8 earlyprintk"; }; @@ -24,14 +19,18 @@ }; timer0: timer@13000000 { + /* TIMER0 runs @ 25MHz */ compatible = "arm,integrator-cp-timer"; + status = "disabled"; }; timer1: timer@13000100 { + /* TIMER1 runs @ 1MHz */ compatible = "arm,integrator-cp-timer"; }; timer2: timer@13000200 { + /* TIMER2 runs @ 1MHz */ compatible = "arm,integrator-cp-timer"; }; -- cgit v1.1 From 80030e3d8ec6414790a5ec67ae4c5eeee82aba98 Mon Sep 17 00:00:00 2001 From: Borislav Petkov Date: Sun, 13 Oct 2013 18:36:29 +0200 Subject: x86/microcode: Correct Kconfig dependencies I have a randconfig here which has enabled only CONFIG_MICROCODE=y CONFIG_MICROCODE_OLD_INTERFACE=y with both # CONFIG_MICROCODE_INTEL is not set # CONFIG_MICROCODE_AMD is not set off. Which makes building the microcode functionality a little pointless. Don't do that in such cases then. Signed-off-by: Borislav Petkov Link: http://lkml.kernel.org/r/1381682189-14470-1-git-send-email-bp@alien8.de Signed-off-by: Ingo Molnar --- arch/x86/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 145d703..f67e839 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -1033,6 +1033,7 @@ config X86_REBOOTFIXUPS config MICROCODE tristate "CPU microcode loading support" + depends on CPU_SUP_AMD || CPU_SUP_INTEL select FW_LOADER ---help--- -- cgit v1.1 From dd3c9c4b603c664fedc12facf180db0f1794aafe Mon Sep 17 00:00:00 2001 From: Russ Anderson Date: Mon, 14 Oct 2013 11:17:34 -0500 Subject: x86: Update UV3 hub revision ID The UV3 hub revision ID is different than expected. The first revision was supposed to start at 1 but instead will start at 0. Signed-off-by: Russ Anderson Cc: # v3.9, v3.10, v3.11 Link: http://lkml.kernel.org/r/20131014161733.GA6274@sgi.com Signed-off-by: Ingo Molnar --- arch/x86/kernel/apic/x2apic_uv_x.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/apic/x2apic_uv_x.c b/arch/x86/kernel/apic/x2apic_uv_x.c index 1191ac1..a419814 100644 --- a/arch/x86/kernel/apic/x2apic_uv_x.c +++ b/arch/x86/kernel/apic/x2apic_uv_x.c @@ -113,7 +113,7 @@ static int __init early_get_pnodeid(void) break; case UV3_HUB_PART_NUMBER: case UV3_HUB_PART_NUMBER_X: - uv_min_hub_revision_id += UV3_HUB_REVISION_BASE - 1; + uv_min_hub_revision_id += UV3_HUB_REVISION_BASE; break; } -- cgit v1.1 From cebf3e40b01bbf88d38dc954397414afaa280023 Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Fri, 11 Oct 2013 09:27:27 +0200 Subject: Revert "ARM: init: add support for reserved memory defined by device tree" This reverts commit 10bcdfb8ba24760f715f0a700c3812747eddddf5. There is no consensus on the bindings for the reserved memory, so the code for handing it will be reverted. Signed-off-by: Marek Szyprowski Signed-off-by: Grant Likely --- arch/arm/mm/init.c | 3 --- 1 file changed, 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c index febaee7..18ec4c5 100644 --- a/arch/arm/mm/init.c +++ b/arch/arm/mm/init.c @@ -17,7 +17,6 @@ #include #include #include -#include #include #include #include @@ -379,8 +378,6 @@ void __init arm_memblock_init(struct meminfo *mi, if (mdesc->reserve) mdesc->reserve(); - early_init_dt_scan_reserved_mem(); - /* * reserve memory for DMA contigouos allocations, * must come from DMA area inside low memory -- cgit v1.1 From 3dbef3e3bf13d74582fe43548f5c570a0cec9b20 Mon Sep 17 00:00:00 2001 From: Raghavendra K T Date: Wed, 9 Oct 2013 14:33:21 +0530 Subject: KVM: Enable pvspinlock after jump_label_init() to avoid VM hang We use jump label to enable pv-spinlock. With the changes in (442e0973e927 Merge branch 'x86/jumplabel'), the jump label behaviour has changed that would result in eventual hang of the VM since we would end up in a situation where slow path locks would halt the vcpus but we will not be able to wakeup the vcpu by lock releaser using unlock kick. Similar problem in Xen and more detailed description is available in a945928ea270 (xen: Do not enable spinlocks before jump_label_init() has executed) This patch splits kvm_spinlock_init to separate jump label changes with pvops patching and also make jump label enabling after jump_label_init(). Signed-off-by: Raghavendra K T Reviewed-by: Paolo Bonzini Reviewed-by: Steven Rostedt Signed-off-by: Gleb Natapov --- arch/x86/kernel/kvm.c | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/kvm.c b/arch/x86/kernel/kvm.c index 697b93a..a0e2a8a 100644 --- a/arch/x86/kernel/kvm.c +++ b/arch/x86/kernel/kvm.c @@ -775,11 +775,22 @@ void __init kvm_spinlock_init(void) if (!kvm_para_has_feature(KVM_FEATURE_PV_UNHALT)) return; - printk(KERN_INFO "KVM setup paravirtual spinlock\n"); + pv_lock_ops.lock_spinning = PV_CALLEE_SAVE(kvm_lock_spinning); + pv_lock_ops.unlock_kick = kvm_unlock_kick; +} + +static __init int kvm_spinlock_init_jump(void) +{ + if (!kvm_para_available()) + return 0; + if (!kvm_para_has_feature(KVM_FEATURE_PV_UNHALT)) + return 0; static_key_slow_inc(¶virt_ticketlocks_enabled); + printk(KERN_INFO "KVM setup paravirtual spinlock\n"); - pv_lock_ops.lock_spinning = PV_CALLEE_SAVE(kvm_lock_spinning); - pv_lock_ops.unlock_kick = kvm_unlock_kick; + return 0; } +early_initcall(kvm_spinlock_init_jump); + #endif /* CONFIG_PARAVIRT_SPINLOCKS */ -- cgit v1.1 From af0ebc40a81c694ad25f034383c13a233c4a2f55 Mon Sep 17 00:00:00 2001 From: Martin Schwidefsky Date: Mon, 7 Oct 2013 16:15:29 +0200 Subject: s390/mm,kvm: fix software dirty bits vs. kvm for old machines For machines without enhanced supression on protection the software dirty bit code forces the pte dirty bit and clears the page protection bit in pgste_set_pte. This is done for all pte types, the check for present ptes is missing. As a result swap ptes and other not-present ptes can get corrupted. Add a check for the _PAGE_PRESENT bit to pgste_set_pte before modifying the pte value. Signed-off-by: Martin Schwidefsky --- arch/s390/include/asm/pgtable.h | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/s390/include/asm/pgtable.h b/arch/s390/include/asm/pgtable.h index 9b60a36..2204400 100644 --- a/arch/s390/include/asm/pgtable.h +++ b/arch/s390/include/asm/pgtable.h @@ -748,7 +748,9 @@ static inline void pgste_set_key(pte_t *ptep, pgste_t pgste, pte_t entry) static inline void pgste_set_pte(pte_t *ptep, pte_t entry) { - if (!MACHINE_HAS_ESOP && (pte_val(entry) & _PAGE_WRITE)) { + if (!MACHINE_HAS_ESOP && + (pte_val(entry) & _PAGE_PRESENT) && + (pte_val(entry) & _PAGE_WRITE)) { /* * Without enhanced suppression-on-protection force * the dirty bit on for all writable ptes. -- cgit v1.1 From 0ebfd313fd4baf3fa1bd02d5f106e377595d4987 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Mon, 14 Oct 2013 12:09:37 +0200 Subject: s390/compat,signal: fix return value of copy_siginfo_(to|from)_user32() The return value of copy_siginfo_(to|from)_user32() gets passed to user space, however we do not convert a positive return value from copy_(to|from)_user to -EFAULT. Therefore these functions (and the calling system calls) my incorrectly return a positive number (bytes not copied) instead of -EFAULT. Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/compat_signal.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/s390/kernel/compat_signal.c b/arch/s390/kernel/compat_signal.c index 1389b63..adaa9e9 100644 --- a/arch/s390/kernel/compat_signal.c +++ b/arch/s390/kernel/compat_signal.c @@ -99,7 +99,7 @@ int copy_siginfo_to_user32(compat_siginfo_t __user *to, siginfo_t *from) break; } } - return err; + return err ? -EFAULT : 0; } int copy_siginfo_from_user32(siginfo_t *to, compat_siginfo_t __user *from) @@ -148,7 +148,7 @@ int copy_siginfo_from_user32(siginfo_t *to, compat_siginfo_t __user *from) break; } } - return err; + return err ? -EFAULT : 0; } static int save_sigregs32(struct pt_regs *regs, _sigregs32 __user *sregs) -- cgit v1.1 From 244066f4be8ce2dc2d2d60f01bceeba55c71a783 Mon Sep 17 00:00:00 2001 From: Max Filippov Date: Tue, 15 Oct 2013 02:22:42 +0400 Subject: xtensa: fix fast_syscall_spill_registers_fixup fast_syscall_spill_registers_fixup was not correctly updated by the 'keep a3 and excsave1 on entry to exception handlers' patch: it doesn't preserve a3 that it gets on entry, breaking _spill_registers in case of page fault on stack during register spilling, leading to unhandled exception in kernel mode. Preserve a3 by saving it in the original _spill_registers stack frame's a3 during exception handling and restoring it afterwards. Also fix comments and function bounds annotations. Reported-by: Baruch Siach Signed-off-by: Max Filippov Tested-by: Baruch Siach Signed-off-by: Chris Zankel --- arch/xtensa/kernel/entry.S | 49 ++++++++++++++++++++++++++++------------------ 1 file changed, 30 insertions(+), 19 deletions(-) (limited to 'arch') diff --git a/arch/xtensa/kernel/entry.S b/arch/xtensa/kernel/entry.S index de1dfa1..21dbe6b 100644 --- a/arch/xtensa/kernel/entry.S +++ b/arch/xtensa/kernel/entry.S @@ -1122,7 +1122,7 @@ ENDPROC(fast_syscall_spill_registers) * a3: exctable, original value in excsave1 */ -fast_syscall_spill_registers_fixup: +ENTRY(fast_syscall_spill_registers_fixup) rsr a2, windowbase # get current windowbase (a2 is saved) xsr a0, depc # restore depc and a0 @@ -1134,22 +1134,26 @@ fast_syscall_spill_registers_fixup: */ xsr a3, excsave1 # get spill-mask - slli a2, a3, 1 # shift left by one + slli a3, a3, 1 # shift left by one - slli a3, a2, 32-WSBITS - src a2, a2, a3 # a1 = xxwww1yyxxxwww1yy...... + slli a2, a3, 32-WSBITS + src a2, a3, a2 # a2 = xxwww1yyxxxwww1yy...... wsr a2, windowstart # set corrected windowstart - rsr a3, excsave1 - l32i a2, a3, EXC_TABLE_DOUBLE_SAVE # restore a2 - l32i a3, a3, EXC_TABLE_PARAM # original WB (in user task) + srli a3, a3, 1 + rsr a2, excsave1 + l32i a2, a2, EXC_TABLE_DOUBLE_SAVE # restore a2 + xsr a2, excsave1 + s32i a3, a2, EXC_TABLE_DOUBLE_SAVE # save a3 + l32i a3, a2, EXC_TABLE_PARAM # original WB (in user task) + xsr a2, excsave1 /* Return to the original (user task) WINDOWBASE. * We leave the following frame behind: * a0, a1, a2 same - * a3: trashed (saved in excsave_1) + * a3: trashed (saved in EXC_TABLE_DOUBLE_SAVE) * depc: depc (we have to return to that address) - * excsave_1: a3 + * excsave_1: exctable */ wsr a3, windowbase @@ -1159,9 +1163,9 @@ fast_syscall_spill_registers_fixup: * a0: return address * a1: used, stack pointer * a2: kernel stack pointer - * a3: available, saved in EXCSAVE_1 + * a3: available * depc: exception address - * excsave: a3 + * excsave: exctable * Note: This frame might be the same as above. */ @@ -1181,9 +1185,12 @@ fast_syscall_spill_registers_fixup: rsr a0, exccause addx4 a0, a0, a3 # find entry in table l32i a0, a0, EXC_TABLE_FAST_USER # load handler + l32i a3, a3, EXC_TABLE_DOUBLE_SAVE jx a0 -fast_syscall_spill_registers_fixup_return: +ENDPROC(fast_syscall_spill_registers_fixup) + +ENTRY(fast_syscall_spill_registers_fixup_return) /* When we return here, all registers have been restored (a2: DEPC) */ @@ -1191,13 +1198,13 @@ fast_syscall_spill_registers_fixup_return: /* Restore fixup handler. */ - xsr a3, excsave1 - movi a2, fast_syscall_spill_registers_fixup - s32i a2, a3, EXC_TABLE_FIXUP - s32i a0, a3, EXC_TABLE_DOUBLE_SAVE - rsr a2, windowbase - s32i a2, a3, EXC_TABLE_PARAM - l32i a2, a3, EXC_TABLE_KSTK + rsr a2, excsave1 + s32i a3, a2, EXC_TABLE_DOUBLE_SAVE + movi a3, fast_syscall_spill_registers_fixup + s32i a3, a2, EXC_TABLE_FIXUP + rsr a3, windowbase + s32i a3, a2, EXC_TABLE_PARAM + l32i a2, a2, EXC_TABLE_KSTK /* Load WB at the time the exception occurred. */ @@ -1206,8 +1213,12 @@ fast_syscall_spill_registers_fixup_return: wsr a3, windowbase rsync + rsr a3, excsave1 + l32i a3, a3, EXC_TABLE_DOUBLE_SAVE + rfde +ENDPROC(fast_syscall_spill_registers_fixup_return) /* * spill all registers. -- cgit v1.1 From cba9a90053e3b7973eff4f1946f33032e98eeed5 Mon Sep 17 00:00:00 2001 From: Baruch Siach Date: Tue, 15 Oct 2013 02:22:43 +0400 Subject: xtensa: don't use alternate signal stack on threads According to create_thread(3): "The new thread does not inherit the creating thread's alternate signal stack". Since commit f9a3879a (Fix sigaltstack corruption among cloned threads), current->sas_ss_size is set to 0 for cloned processes sharing VM with their parent. Don't use the (nonexistent) alternate signal stack in this case. This has been broken since commit 29c4dfd9 ([XTENSA] Remove non-rt signal handling). Fixes the SA_ONSTACK part of the nptl/tst-cancel20 test from uClibc. Cc: Signed-off-by: Baruch Siach Signed-off-by: Max Filippov Signed-off-by: Chris Zankel --- arch/xtensa/kernel/signal.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/xtensa/kernel/signal.c b/arch/xtensa/kernel/signal.c index 718eca1..98b67d5 100644 --- a/arch/xtensa/kernel/signal.c +++ b/arch/xtensa/kernel/signal.c @@ -341,7 +341,7 @@ static int setup_frame(int sig, struct k_sigaction *ka, siginfo_t *info, sp = regs->areg[1]; - if ((ka->sa.sa_flags & SA_ONSTACK) != 0 && ! on_sig_stack(sp)) { + if ((ka->sa.sa_flags & SA_ONSTACK) != 0 && sas_ss_flags(sp) == 0) { sp = current->sas_ss_sp + current->sas_ss_size; } -- cgit v1.1 From f447fd30afdbb40c913054edaacf1a32df7a55d7 Mon Sep 17 00:00:00 2001 From: Thomas Meyer Date: Thu, 19 Sep 2013 23:42:22 +0200 Subject: xtensa: Cocci spatch "noderef" sizeof when applied to a pointer typed expression gives the size of the pointer. Found by coccinelle spatch "misc/noderef.cocci" Signed-off-by: Thomas Meyer Signed-off-by: Chris Zankel --- arch/xtensa/platforms/iss/network.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/xtensa/platforms/iss/network.c b/arch/xtensa/platforms/iss/network.c index 56f88b7..e9e1aad 100644 --- a/arch/xtensa/platforms/iss/network.c +++ b/arch/xtensa/platforms/iss/network.c @@ -737,7 +737,8 @@ static int __init iss_net_setup(char *str) return 1; } - if ((new = alloc_bootmem(sizeof new)) == NULL) { + new = alloc_bootmem(sizeof(*new)); + if (new == NULL) { printk("Alloc_bootmem failed\n"); return 1; } -- cgit v1.1 From a446e72bc15c7bfd2c953e56064ace3566c79b0e Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Mon, 14 Oct 2013 21:35:44 +0200 Subject: Revert "parisc: Export flush_cache_page() (needed by lustre)" This reverts commit 320c90be7ba1c371e882edff57272a89b213d136. Christoph Hellwig commented: This one shouldn't go in - Geert sent it a bit prematurely, as Lustre shouldn't use it just to reimplement core VM functionality (which it shouldn't use either, but that's a separate story). Signed-off-by: Helge Deller --- arch/parisc/kernel/cache.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/parisc/kernel/cache.c b/arch/parisc/kernel/cache.c index b521c0a..c035673 100644 --- a/arch/parisc/kernel/cache.c +++ b/arch/parisc/kernel/cache.c @@ -602,7 +602,6 @@ flush_cache_page(struct vm_area_struct *vma, unsigned long vmaddr, unsigned long __flush_cache_page(vma, vmaddr, PFN_PHYS(pfn)); } } -EXPORT_SYMBOL_GPL(flush_cache_page); #ifdef CONFIG_PARISC_TMPALIAS -- cgit v1.1 From c1b14041aa86800cfd9e21b280b0eaee885fa623 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Mon, 14 Oct 2013 22:55:36 +0200 Subject: parisc: enable DEVTMPFS, DEVTMPFS_MOUNT and BLK_DEV_INITRD in defconfigs Latest udev requires that DEVTMPFS and DEVTMPFS_MOUNT are enabled, else initrd will fail to find root filesystem. Enable missing BLK_DEV_INITRD for B180 and C3000 machines. Signed-off-by: Helge Deller --- arch/parisc/configs/712_defconfig | 2 ++ arch/parisc/configs/a500_defconfig | 2 ++ arch/parisc/configs/b180_defconfig | 3 +++ arch/parisc/configs/c3000_defconfig | 3 +++ arch/parisc/configs/c8000_defconfig | 2 ++ arch/parisc/configs/default_defconfig | 2 ++ 6 files changed, 14 insertions(+) (limited to 'arch') diff --git a/arch/parisc/configs/712_defconfig b/arch/parisc/configs/712_defconfig index 0f90569..9387cc2 100644 --- a/arch/parisc/configs/712_defconfig +++ b/arch/parisc/configs/712_defconfig @@ -40,6 +40,8 @@ CONFIG_IP_NF_QUEUE=m CONFIG_LLC2=m CONFIG_NET_PKTGEN=m CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_DEVTMPFS=y +CONFIG_DEVTMPFS_MOUNT=y # CONFIG_STANDALONE is not set # CONFIG_PREVENT_FIRMWARE_BUILD is not set CONFIG_PARPORT=y diff --git a/arch/parisc/configs/a500_defconfig b/arch/parisc/configs/a500_defconfig index b647b18..9002532 100644 --- a/arch/parisc/configs/a500_defconfig +++ b/arch/parisc/configs/a500_defconfig @@ -79,6 +79,8 @@ CONFIG_IP_DCCP=m CONFIG_LLC2=m CONFIG_NET_PKTGEN=m CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_DEVTMPFS=y +CONFIG_DEVTMPFS_MOUNT=y # CONFIG_STANDALONE is not set # CONFIG_PREVENT_FIRMWARE_BUILD is not set CONFIG_BLK_DEV_UMEM=m diff --git a/arch/parisc/configs/b180_defconfig b/arch/parisc/configs/b180_defconfig index e289f5b..f1a0c25 100644 --- a/arch/parisc/configs/b180_defconfig +++ b/arch/parisc/configs/b180_defconfig @@ -4,6 +4,7 @@ CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=16 CONFIG_SYSFS_DEPRECATED_V2=y +CONFIG_BLK_DEV_INITRD=y CONFIG_SLAB=y CONFIG_MODULES=y CONFIG_MODVERSIONS=y @@ -27,6 +28,8 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_LRO is not set CONFIG_IPV6=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_DEVTMPFS=y +CONFIG_DEVTMPFS_MOUNT=y # CONFIG_PREVENT_FIRMWARE_BUILD is not set CONFIG_PARPORT=y CONFIG_PARPORT_PC=y diff --git a/arch/parisc/configs/c3000_defconfig b/arch/parisc/configs/c3000_defconfig index 311ca36..ec1b014 100644 --- a/arch/parisc/configs/c3000_defconfig +++ b/arch/parisc/configs/c3000_defconfig @@ -5,6 +5,7 @@ CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=16 CONFIG_SYSFS_DEPRECATED_V2=y +CONFIG_BLK_DEV_INITRD=y # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_EXPERT=y CONFIG_KALLSYMS_ALL=y @@ -39,6 +40,8 @@ CONFIG_NETFILTER_DEBUG=y CONFIG_IP_NF_QUEUE=m CONFIG_NET_PKTGEN=m CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_DEVTMPFS=y +CONFIG_DEVTMPFS_MOUNT=y # CONFIG_STANDALONE is not set # CONFIG_PREVENT_FIRMWARE_BUILD is not set CONFIG_BLK_DEV_UMEM=m diff --git a/arch/parisc/configs/c8000_defconfig b/arch/parisc/configs/c8000_defconfig index f110063..e1c8d20 100644 --- a/arch/parisc/configs/c8000_defconfig +++ b/arch/parisc/configs/c8000_defconfig @@ -62,6 +62,8 @@ CONFIG_TIPC=m CONFIG_LLC2=m CONFIG_DNS_RESOLVER=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_DEVTMPFS=y +CONFIG_DEVTMPFS_MOUNT=y # CONFIG_STANDALONE is not set CONFIG_PARPORT=y CONFIG_PARPORT_PC=y diff --git a/arch/parisc/configs/default_defconfig b/arch/parisc/configs/default_defconfig index dfe88f6..ba61495 100644 --- a/arch/parisc/configs/default_defconfig +++ b/arch/parisc/configs/default_defconfig @@ -49,6 +49,8 @@ CONFIG_INET6_ESP=y CONFIG_INET6_IPCOMP=y CONFIG_LLC2=m CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_DEVTMPFS=y +CONFIG_DEVTMPFS_MOUNT=y # CONFIG_STANDALONE is not set # CONFIG_PREVENT_FIRMWARE_BUILD is not set CONFIG_PARPORT=y -- cgit v1.1 From 8c071b0f19dfa230335d22ce56a8fab5bd20cedc Mon Sep 17 00:00:00 2001 From: Martin Schwidefsky Date: Thu, 17 Oct 2013 12:38:17 +0200 Subject: s390/time: correct use of store clock fast The result of the store-clock-fast (STCKF) instruction is a bit fuzzy. It can happen that the value stored on one CPU is smaller than the value stored on another CPU, although the order of the stores is the other way around. This can cause deltas of get_tod_clock() values to become negative when they should not be. We need to be more careful with store-clock-fast, this patch partially reverts git commit e4b7b4238e666682555461fa52eecd74652f36bb "time: always use stckf instead of stck if available". The get_tod_clock() function now uses the store-clock-extended (STCKE) instruction. get_tod_clock_fast() can be used if the fuzziness of store-clock-fast is acceptable e.g. for wait loops local to a CPU. Signed-off-by: Martin Schwidefsky --- arch/s390/include/asm/timex.h | 28 ++++++++++++++-------------- arch/s390/kernel/debug.c | 2 +- arch/s390/kvm/interrupt.c | 6 +++--- arch/s390/lib/delay.c | 14 +++++++------- 4 files changed, 25 insertions(+), 25 deletions(-) (limited to 'arch') diff --git a/arch/s390/include/asm/timex.h b/arch/s390/include/asm/timex.h index 8ad8af9..819b94d 100644 --- a/arch/s390/include/asm/timex.h +++ b/arch/s390/include/asm/timex.h @@ -71,30 +71,30 @@ static inline void local_tick_enable(unsigned long long comp) typedef unsigned long long cycles_t; -static inline unsigned long long get_tod_clock(void) -{ - unsigned long long clk; - -#ifdef CONFIG_HAVE_MARCH_Z9_109_FEATURES - asm volatile(".insn s,0xb27c0000,%0" : "=Q" (clk) : : "cc"); -#else - asm volatile("stck %0" : "=Q" (clk) : : "cc"); -#endif - return clk; -} - static inline void get_tod_clock_ext(char *clk) { asm volatile("stcke %0" : "=Q" (*clk) : : "cc"); } -static inline unsigned long long get_tod_clock_xt(void) +static inline unsigned long long get_tod_clock(void) { unsigned char clk[16]; get_tod_clock_ext(clk); return *((unsigned long long *)&clk[1]); } +static inline unsigned long long get_tod_clock_fast(void) +{ +#ifdef CONFIG_HAVE_MARCH_Z9_109_FEATURES + unsigned long long clk; + + asm volatile("stckf %0" : "=Q" (clk) : : "cc"); + return clk; +#else + return get_tod_clock(); +#endif +} + static inline cycles_t get_cycles(void) { return (cycles_t) get_tod_clock() >> 2; @@ -125,7 +125,7 @@ extern u64 sched_clock_base_cc; */ static inline unsigned long long get_tod_clock_monotonic(void) { - return get_tod_clock_xt() - sched_clock_base_cc; + return get_tod_clock() - sched_clock_base_cc; } /** diff --git a/arch/s390/kernel/debug.c b/arch/s390/kernel/debug.c index f1279dc..17d62fe 100644 --- a/arch/s390/kernel/debug.c +++ b/arch/s390/kernel/debug.c @@ -867,7 +867,7 @@ static inline void debug_finish_entry(debug_info_t * id, debug_entry_t* active, int level, int exception) { - active->id.stck = get_tod_clock(); + active->id.stck = get_tod_clock_fast(); active->id.fields.cpuid = smp_processor_id(); active->caller = __builtin_return_address(0); active->id.fields.exception = exception; diff --git a/arch/s390/kvm/interrupt.c b/arch/s390/kvm/interrupt.c index 7f35cb3..7f1f7ac 100644 --- a/arch/s390/kvm/interrupt.c +++ b/arch/s390/kvm/interrupt.c @@ -385,7 +385,7 @@ static int kvm_cpu_has_interrupt(struct kvm_vcpu *vcpu) } if ((!rc) && (vcpu->arch.sie_block->ckc < - get_tod_clock() + vcpu->arch.sie_block->epoch)) { + get_tod_clock_fast() + vcpu->arch.sie_block->epoch)) { if ((!psw_extint_disabled(vcpu)) && (vcpu->arch.sie_block->gcr[0] & 0x800ul)) rc = 1; @@ -425,7 +425,7 @@ int kvm_s390_handle_wait(struct kvm_vcpu *vcpu) goto no_timer; } - now = get_tod_clock() + vcpu->arch.sie_block->epoch; + now = get_tod_clock_fast() + vcpu->arch.sie_block->epoch; if (vcpu->arch.sie_block->ckc < now) { __unset_cpu_idle(vcpu); return 0; @@ -515,7 +515,7 @@ void kvm_s390_deliver_pending_interrupts(struct kvm_vcpu *vcpu) } if ((vcpu->arch.sie_block->ckc < - get_tod_clock() + vcpu->arch.sie_block->epoch)) + get_tod_clock_fast() + vcpu->arch.sie_block->epoch)) __try_deliver_ckc_interrupt(vcpu); if (atomic_read(&fi->active)) { diff --git a/arch/s390/lib/delay.c b/arch/s390/lib/delay.c index 57c87d7..a9f3d00 100644 --- a/arch/s390/lib/delay.c +++ b/arch/s390/lib/delay.c @@ -44,7 +44,7 @@ static void __udelay_disabled(unsigned long long usecs) do { set_clock_comparator(end); vtime_stop_cpu(); - } while (get_tod_clock() < end); + } while (get_tod_clock_fast() < end); lockdep_on(); __ctl_load(cr0, 0, 0); __ctl_load(cr6, 6, 6); @@ -55,7 +55,7 @@ static void __udelay_enabled(unsigned long long usecs) { u64 clock_saved, end; - end = get_tod_clock() + (usecs << 12); + end = get_tod_clock_fast() + (usecs << 12); do { clock_saved = 0; if (end < S390_lowcore.clock_comparator) { @@ -65,7 +65,7 @@ static void __udelay_enabled(unsigned long long usecs) vtime_stop_cpu(); if (clock_saved) local_tick_enable(clock_saved); - } while (get_tod_clock() < end); + } while (get_tod_clock_fast() < end); } /* @@ -109,8 +109,8 @@ void udelay_simple(unsigned long long usecs) { u64 end; - end = get_tod_clock() + (usecs << 12); - while (get_tod_clock() < end) + end = get_tod_clock_fast() + (usecs << 12); + while (get_tod_clock_fast() < end) cpu_relax(); } @@ -120,10 +120,10 @@ void __ndelay(unsigned long long nsecs) nsecs <<= 9; do_div(nsecs, 125); - end = get_tod_clock() + nsecs; + end = get_tod_clock_fast() + nsecs; if (nsecs & ~0xfffUL) __udelay(nsecs >> 12); - while (get_tod_clock() < end) + while (get_tod_clock_fast() < end) barrier(); } EXPORT_SYMBOL(__ndelay); -- cgit v1.1 From 54e181e073fc1415e41917d725ebdbd7de956455 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Sat, 26 Oct 2013 23:19:25 +0200 Subject: parisc: Do not crash 64bit SMP kernels on machines with >= 4GB RAM Since the beginning of the parisc-linux port, sometimes 64bit SMP kernels were not able to bring up other CPUs than the monarch CPU and instead crashed the kernel. The reason was unclear, esp. since it involved various machines (e.g. J5600, J6750 and SuperDome). Testing showed, that those crashes didn't happened when less than 4GB were installed, or if a 32bit Linux kernel was booted. In the end, the fix for those SMP problems is trivial: During the early phase of the initialization of the CPUs, including the monarch CPU, the PDC_PSW firmware function to enable WIDE (=64bit) mode is called. It's documented that this firmware function may clobber various registers, and one one of those possibly clobbered registers is %cr30 which holds the task thread info pointer. Now, if %cr30 would always have been clobbered, then this bug would have been detected much earlier. But lots of testing finally showed, that - at least for %cr30 - on some machines only the upper 32bits of the 64bit register suddenly turned zero after the firmware call. So, after finding the root cause, the explanation for the various crashes became clear: - On 32bit SMP Linux kernels all upper 32bit were zero, so we didn't faced this problem. - Monarch CPUs in 64bit mode always booted sucessfully, because the inital task thread info pointer was below 4GB. - Secondary CPUs booted sucessfully on machines with less than 4GB RAM because the upper 32bit were zero anyay. - Secondary CPus failed to boot if we had more than 4GB RAM and the task thread info pointer was located above the 4GB boundary. Finally, the patch to fix this problem is trivial by saving the %cr30 register before the firmware call and restoring it afterwards. Signed-off-by: Helge Deller Signed-off-by: John David Anglin Cc: # 2.6.12+ Signed-off-by: Helge Deller --- arch/parisc/kernel/head.S | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch') diff --git a/arch/parisc/kernel/head.S b/arch/parisc/kernel/head.S index 37aabd7..d2d5825 100644 --- a/arch/parisc/kernel/head.S +++ b/arch/parisc/kernel/head.S @@ -195,6 +195,8 @@ common_stext: ldw MEM_PDC_HI(%r0),%r6 depd %r6, 31, 32, %r3 /* move to upper word */ + mfctl %cr30,%r6 /* PCX-W2 firmware bug */ + ldo PDC_PSW(%r0),%arg0 /* 21 */ ldo PDC_PSW_SET_DEFAULTS(%r0),%arg1 /* 2 */ ldo PDC_PSW_WIDE_BIT(%r0),%arg2 /* 2 */ @@ -203,6 +205,8 @@ common_stext: copy %r0,%arg3 stext_pdc_ret: + mtctl %r6,%cr30 /* restore task thread info */ + /* restore rfi target address*/ ldd TI_TASK-THREAD_SZ_ALGN(%sp), %r10 tophys_r1 %r10 -- cgit v1.1 From d780a31271b2f455cb4b83eb018ecfb1c28ef5c1 Mon Sep 17 00:00:00 2001 From: Tim Gardner Date: Tue, 29 Oct 2013 09:13:54 -0600 Subject: KVM: Fix modprobe failure for kvm_intel/kvm_amd The x86 specific kvm init creates a new conflicting debugfs directory which causes modprobe issues with kvm_intel and kvm_amd. For example, sudo modprobe kvm_amd modprobe: ERROR: could not insert 'kvm_amd': Bad address The simplest fix is to just rename the directory. The following KVM config options are set: CONFIG_KVM_GUEST=y CONFIG_KVM_DEBUG_FS=y CONFIG_HAVE_KVM=y CONFIG_HAVE_KVM_IRQCHIP=y CONFIG_HAVE_KVM_IRQ_ROUTING=y CONFIG_HAVE_KVM_EVENTFD=y CONFIG_KVM_APIC_ARCHITECTURE=y CONFIG_KVM_MMIO=y CONFIG_KVM_ASYNC_PF=y CONFIG_HAVE_KVM_MSI=y CONFIG_HAVE_KVM_CPU_RELAX_INTERCEPT=y CONFIG_KVM=m CONFIG_KVM_INTEL=m CONFIG_KVM_AMD=m CONFIG_KVM_DEVICE_ASSIGNMENT=y Cc: Thomas Gleixner Cc: Ingo Molnar Cc: "H. Peter Anvin" Cc: Gleb Natapov Cc: Raghavendra K T Cc: Marcelo Tosatti Signed-off-by: Tim Gardner [Change debugfs directory name. - Paolo] Signed-off-by: Paolo Bonzini --- arch/x86/kernel/kvm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/kvm.c b/arch/x86/kernel/kvm.c index a0e2a8a..b2046e4 100644 --- a/arch/x86/kernel/kvm.c +++ b/arch/x86/kernel/kvm.c @@ -609,7 +609,7 @@ static struct dentry *d_kvm_debug; struct dentry *kvm_init_debugfs(void) { - d_kvm_debug = debugfs_create_dir("kvm", NULL); + d_kvm_debug = debugfs_create_dir("kvm-guest", NULL); if (!d_kvm_debug) printk(KERN_WARNING "Could not create 'kvm' debugfs directory\n"); -- cgit v1.1 From 201f99f170df14ba52ea4c52847779042b7a623b Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Tue, 29 Oct 2013 22:06:04 +0300 Subject: uml: check length in exitcode_proc_write() We don't cap the size of buffer from the user so we could write past the end of the array here. Only root can write to this file. Reported-by: Nico Golde Reported-by: Fabian Yamaguchi Signed-off-by: Dan Carpenter Cc: stable@kernel.org Signed-off-by: Linus Torvalds --- arch/um/kernel/exitcode.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/um/kernel/exitcode.c b/arch/um/kernel/exitcode.c index 829df49..41ebbfe 100644 --- a/arch/um/kernel/exitcode.c +++ b/arch/um/kernel/exitcode.c @@ -40,9 +40,11 @@ static ssize_t exitcode_proc_write(struct file *file, const char __user *buffer, size_t count, loff_t *pos) { char *end, buf[sizeof("nnnnn\0")]; + size_t size; int tmp; - if (copy_from_user(buf, buffer, count)) + size = min(count, sizeof(buf)); + if (copy_from_user(buf, buffer, size)) return -EFAULT; tmp = simple_strtol(buf, &end, 0); -- cgit v1.1 From bd09d9a35111b6ffc0c7585d3853d0ec7f9f1eb4 Mon Sep 17 00:00:00 2001 From: Greg Thelen Date: Wed, 30 Oct 2013 13:56:20 -0700 Subject: percpu: fix this_cpu_sub() subtrahend casting for unsigneds this_cpu_sub() is implemented as negation and addition. This patch casts the adjustment to the counter type before negation to sign extend the adjustment. This helps in cases where the counter type is wider than an unsigned adjustment. An alternative to this patch is to declare such operations unsupported, but it seemed useful to avoid surprises. This patch specifically helps the following example: unsigned int delta = 1 preempt_disable() this_cpu_write(long_counter, 0) this_cpu_sub(long_counter, delta) preempt_enable() Before this change long_counter on a 64 bit machine ends with value 0xffffffff, rather than 0xffffffffffffffff. This is because this_cpu_sub(pcp, delta) boils down to this_cpu_add(pcp, -delta), which is basically: long_counter = 0 + 0xffffffff Also apply the same cast to: __this_cpu_sub() __this_cpu_sub_return() this_cpu_sub_return() All percpu_test.ko passes, especially the following cases which previously failed: l -= ui_one; __this_cpu_sub(long_counter, ui_one); CHECK(l, long_counter, -1); l -= ui_one; this_cpu_sub(long_counter, ui_one); CHECK(l, long_counter, -1); CHECK(l, long_counter, 0xffffffffffffffff); ul -= ui_one; __this_cpu_sub(ulong_counter, ui_one); CHECK(ul, ulong_counter, -1); CHECK(ul, ulong_counter, 0xffffffffffffffff); ul = this_cpu_sub_return(ulong_counter, ui_one); CHECK(ul, ulong_counter, 2); ul = __this_cpu_sub_return(ulong_counter, ui_one); CHECK(ul, ulong_counter, 1); Signed-off-by: Greg Thelen Acked-by: Tejun Heo Acked-by: Johannes Weiner Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/x86/include/asm/percpu.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/include/asm/percpu.h b/arch/x86/include/asm/percpu.h index 0da5200..b3e18f8 100644 --- a/arch/x86/include/asm/percpu.h +++ b/arch/x86/include/asm/percpu.h @@ -128,7 +128,8 @@ do { \ do { \ typedef typeof(var) pao_T__; \ const int pao_ID__ = (__builtin_constant_p(val) && \ - ((val) == 1 || (val) == -1)) ? (val) : 0; \ + ((val) == 1 || (val) == -1)) ? \ + (int)(val) : 0; \ if (0) { \ pao_T__ pao_tmp__; \ pao_tmp__ = (val); \ -- cgit v1.1