From 105462632c37ea5484ebae7db6e85e0aaac28f4b Mon Sep 17 00:00:00 2001 From: Anders Blomdell Date: Fri, 24 Oct 2008 14:54:08 +0200 Subject: avr32: Enable pullup on USART TX lines Make USART initialization conform to Section 24.6.1 in the AT32AP7000 manual, i.e. "To prevent the TXD line from falling when the USART is disabled, the use of an internal pull up is mandatory." Signed-off-by: Anders Blomdell [haavard.skinnemoen@atmel.com: enable pullup on RX as well] Signed-off-by: Haavard Skinnemoen --- arch/avr32/mach-at32ap/at32ap700x.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c index 0c6e02f..066252e 100644 --- a/arch/avr32/mach-at32ap/at32ap700x.c +++ b/arch/avr32/mach-at32ap/at32ap700x.c @@ -967,28 +967,28 @@ static inline void configure_usart0_pins(void) { u32 pin_mask = (1 << 8) | (1 << 9); /* RXD & TXD */ - select_peripheral(PIOA, pin_mask, PERIPH_B, 0); + select_peripheral(PIOA, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP); } static inline void configure_usart1_pins(void) { u32 pin_mask = (1 << 17) | (1 << 18); /* RXD & TXD */ - select_peripheral(PIOA, pin_mask, PERIPH_A, 0); + select_peripheral(PIOA, pin_mask, PERIPH_A, AT32_GPIOF_PULLUP); } static inline void configure_usart2_pins(void) { u32 pin_mask = (1 << 26) | (1 << 27); /* RXD & TXD */ - select_peripheral(PIOB, pin_mask, PERIPH_B, 0); + select_peripheral(PIOB, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP); } static inline void configure_usart3_pins(void) { u32 pin_mask = (1 << 18) | (1 << 17); /* RXD & TXD */ - select_peripheral(PIOB, pin_mask, PERIPH_B, 0); + select_peripheral(PIOB, pin_mask, PERIPH_B, AT32_GPIOF_PULLUP); } static struct platform_device *__initdata at32_usarts[4]; -- cgit v1.1 From 6c2e94033df5ca11149e52dd179b8dde3172e9bf Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Fri, 7 Nov 2008 12:33:49 +0100 Subject: x86: apic honour irq affinity which was set in early boot setup_ioapic_dest() is called after the non boot cpus have been brought up. It sets the irq affinity of all already configured interrupts to all cpus and ignores affinity settings which were done by the early bootup code. If the IRQ_NO_BALANCING or IRQ_AFFINITY_SET flags are set then use the affinity mask from the irq descriptor and not TARGET_CPUS. Signed-off-by: Thomas Gleixner Signed-off-by: Ingo Molnar --- arch/x86/kernel/io_apic.c | 26 +++++++++++++++++++++----- 1 file changed, 21 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/io_apic.c b/arch/x86/kernel/io_apic.c index 7a3f202..988ee89 100644 --- a/arch/x86/kernel/io_apic.c +++ b/arch/x86/kernel/io_apic.c @@ -3761,7 +3761,9 @@ int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity) void __init setup_ioapic_dest(void) { int pin, ioapic, irq, irq_entry; + struct irq_desc *desc; struct irq_cfg *cfg; + cpumask_t mask; if (skip_ioapic_setup == 1) return; @@ -3778,16 +3780,30 @@ void __init setup_ioapic_dest(void) * cpu is online. */ cfg = irq_cfg(irq); - if (!cfg->vector) + if (!cfg->vector) { setup_IO_APIC_irq(ioapic, pin, irq, irq_trigger(irq_entry), irq_polarity(irq_entry)); + continue; + + } + + /* + * Honour affinities which have been set in early boot + */ + desc = irq_to_desc(irq); + if (desc->status & + (IRQ_NO_BALANCING | IRQ_AFFINITY_SET)) + mask = desc->affinity; + else + mask = TARGET_CPUS; + #ifdef CONFIG_INTR_REMAP - else if (intr_remapping_enabled) - set_ir_ioapic_affinity_irq(irq, TARGET_CPUS); -#endif + if (intr_remapping_enabled) + set_ir_ioapic_affinity_irq(irq, mask); else - set_ioapic_affinity_irq(irq, TARGET_CPUS); +#endif + set_ioapic_affinity_irq(irq, mask); } } -- cgit v1.1 From 5907630ffc2b2d133de2db18963ee5a6c5af7878 Mon Sep 17 00:00:00 2001 From: Grant Erickson Date: Wed, 29 Oct 2008 11:41:14 +0000 Subject: powerpc/40x: Limit allocable DRAM during early mapping If the size of DRAM is not an exact power of two, we may not have covered DRAM in its entirety with large 16 and 4 MiB pages. If that is the case, we can get non-recoverable page faults when doing the final PTE mappings for the non-large page PTEs. Consequently, we restrict the top end of DRAM currently allocable by updating '__initial_memory_limit_addr' so that calls to the LMB to allocate PTEs for "tail" coverage with normal-sized pages (or other reasons) do not attempt to allocate outside the allowed range. Signed-off-by: Grant Erickson Signed-off-by: Josh Boyer --- arch/powerpc/mm/40x_mmu.c | 16 ++++++++++++++-- 1 file changed, 14 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/mm/40x_mmu.c b/arch/powerpc/mm/40x_mmu.c index cecbbc7..29954dc 100644 --- a/arch/powerpc/mm/40x_mmu.c +++ b/arch/powerpc/mm/40x_mmu.c @@ -93,7 +93,7 @@ void __init MMU_init_hw(void) unsigned long __init mmu_mapin_ram(void) { - unsigned long v, s; + unsigned long v, s, mapped; phys_addr_t p; v = KERNELBASE; @@ -130,5 +130,17 @@ unsigned long __init mmu_mapin_ram(void) s -= LARGE_PAGE_SIZE_4M; } - return total_lowmem - s; + mapped = total_lowmem - s; + + /* If the size of RAM is not an exact power of two, we may not + * have covered RAM in its entirety with 16 and 4 MiB + * pages. Consequently, restrict the top end of RAM currently + * allocable so that calls to the LMB to allocate PTEs for "tail" + * coverage with normal-sized pages (or other reasons) do not + * attempt to allocate outside the allowed range. + */ + + __initial_memory_limit_addr = memstart_addr + mapped; + + return mapped; } -- cgit v1.1 From 6612d9b0b8208c2ade3a16b8302a271ec81d45f6 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Tue, 11 Nov 2008 16:02:43 +0000 Subject: powerpc/44x: Fix 460EX/460GT machine check handling Those cores use the 440A type machine check (ie, they have MCSRR0/MCSRR1). They thus need to call the appropriate fixup function to hook the right variant of the exception. Without this, all machine checks become fatal due to loss of context when entering the exception handler. Signed-off-by: Benjamin Herrenschmidt Signed-off-by: Josh Boyer --- arch/powerpc/kernel/cpu_setup_44x.S | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/cpu_setup_44x.S b/arch/powerpc/kernel/cpu_setup_44x.S index 80cac98..31c18b5 100644 --- a/arch/powerpc/kernel/cpu_setup_44x.S +++ b/arch/powerpc/kernel/cpu_setup_44x.S @@ -34,7 +34,12 @@ _GLOBAL(__setup_cpu_440grx) blr _GLOBAL(__setup_cpu_460ex) _GLOBAL(__setup_cpu_460gt) - b __init_fpu_44x + mflr r4 + bl __init_fpu_44x + bl __fixup_440A_mcheck + mtlr r4 + blr + _GLOBAL(__setup_cpu_440gx) _GLOBAL(__setup_cpu_440spe) b __fixup_440A_mcheck -- cgit v1.1 From 847cdf42d589882aca683b6fb65b2c7832e92231 Mon Sep 17 00:00:00 2001 From: Grant Likely Date: Fri, 14 Nov 2008 05:19:00 -0700 Subject: powerpc/mpc5200: fix bestcomm Kconfig dependencies Without this patch it is possible to select drivers which require bestcomm support without bestcomm support being selected. This patch reworks the bestcomm dependencies to ensure the correct bestcomm tasks are always enabled. Reported-by: Hans Lehmann Signed-off-by: Grant Likely --- arch/powerpc/sysdev/bestcomm/Kconfig | 9 +++------ 1 file changed, 3 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/bestcomm/Kconfig b/arch/powerpc/sysdev/bestcomm/Kconfig index 57cc565..0b192a1 100644 --- a/arch/powerpc/sysdev/bestcomm/Kconfig +++ b/arch/powerpc/sysdev/bestcomm/Kconfig @@ -17,23 +17,20 @@ config PPC_BESTCOMM answer Y or M. Otherwise say N. config PPC_BESTCOMM_ATA - tristate "Bestcomm ATA task support" + tristate depends on PPC_BESTCOMM - default n help This option enables the support for the ATA task. config PPC_BESTCOMM_FEC - tristate "Bestcomm FEC tasks support" + tristate depends on PPC_BESTCOMM - default n help This option enables the support for the FEC tasks. config PPC_BESTCOMM_GEN_BD - tristate "Bestcomm GenBD tasks support" + tristate depends on PPC_BESTCOMM - default n help This option enables the support for the GenBD tasks. -- cgit v1.1 From a108096878aa6cb744b5280ca59395b6c0152d14 Mon Sep 17 00:00:00 2001 From: Grant Likely Date: Fri, 14 Nov 2008 09:59:48 -0700 Subject: powerpc/virtex: fix various format/casting printk mismatches Various printk format string in code used by the Xilinx Virtex platform are not 32-bit/64-bit safe. Add correct casting to fix the bugs. Reported-by: Josh Boyer Signed-off-by: Grant Likely Acked-by: Josh Boyer --- arch/powerpc/sysdev/xilinx_intc.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/xilinx_intc.c b/arch/powerpc/sysdev/xilinx_intc.c index b7aefd0..a22e1a2 100644 --- a/arch/powerpc/sysdev/xilinx_intc.c +++ b/arch/powerpc/sysdev/xilinx_intc.c @@ -107,8 +107,8 @@ xilinx_intc_init(struct device_node *np) } regs = ioremap(res.start, 32); - printk(KERN_INFO "Xilinx intc at 0x%08LX mapped to 0x%p\n", - res.start, regs); + printk(KERN_INFO "Xilinx intc at 0x%08llx mapped to 0x%p\n", + (unsigned long long) res.start, regs); /* Setup interrupt controller */ out_be32(regs + XINTC_IER, 0); /* disable all irqs */ -- cgit v1.1 From c7c2ffb4fb92ad79e842226aa547adb5bd045b86 Mon Sep 17 00:00:00 2001 From: Grant Likely Date: Fri, 14 Nov 2008 10:22:02 -0700 Subject: powerpc/52xx: update defconfigs Signed-off-by: Grant Likely --- arch/powerpc/configs/52xx/cm5200_defconfig | 169 ++++++-- arch/powerpc/configs/52xx/lite5200b_defconfig | 206 ++++++--- arch/powerpc/configs/52xx/motionpro_defconfig | 168 ++++++-- arch/powerpc/configs/52xx/pcm030_defconfig | 182 +++++--- arch/powerpc/configs/52xx/tqm5200_defconfig | 180 ++++++-- arch/powerpc/configs/mpc5200_defconfig | 573 ++++++++++++++++++++------ 6 files changed, 1117 insertions(+), 361 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/configs/52xx/cm5200_defconfig b/arch/powerpc/configs/52xx/cm5200_defconfig index c10f739..3df6274 100644 --- a/arch/powerpc/configs/52xx/cm5200_defconfig +++ b/arch/powerpc/configs/52xx/cm5200_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.25 -# Tue Apr 29 07:11:37 2008 +# Linux kernel version: 2.6.28-rc4 +# Thu Nov 13 02:12:40 2008 # # CONFIG_PPC64 is not set @@ -22,7 +22,7 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 -CONFIG_PPC_MERGE=y +# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set CONFIG_MMU=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_GENERIC_TIME=y @@ -32,6 +32,7 @@ CONFIG_GENERIC_HARDIRQS=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y @@ -102,6 +103,7 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLUB_DEBUG=y # CONFIG_SLAB is not set @@ -110,9 +112,13 @@ CONFIG_SLUB=y # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y -CONFIG_PROC_PAGE_MONITOR=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +CONFIG_HAVE_CLK=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set @@ -123,6 +129,7 @@ CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -137,19 +144,16 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_PPC_82xx is not set -# CONFIG_PPC_83xx is not set -# CONFIG_PPC_86xx is not set CONFIG_CLASSIC32=y # CONFIG_PPC_CHRP is not set -# CONFIG_PPC_MPC512x is not set -# CONFIG_PPC_MPC5121 is not set # CONFIG_MPC5121_ADS is not set +# CONFIG_MPC5121_GENERIC is not set CONFIG_PPC_MPC52xx=y CONFIG_PPC_MPC5200_SIMPLE=y # CONFIG_PPC_EFIKA is not set @@ -159,7 +163,10 @@ CONFIG_PPC_MPC5200_SIMPLE=y # CONFIG_PPC_PMAC is not set # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PPC_82xx is not set # CONFIG_PQ2ADS is not set +# CONFIG_PPC_83xx is not set +# CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set # CONFIG_IPIC is not set # CONFIG_MPIC is not set @@ -183,7 +190,6 @@ CONFIG_PPC_BESTCOMM_FEC=y # Kernel options # # CONFIG_HIGHMEM is not set -# CONFIG_TICK_ONESHOT is not set # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set CONFIG_GENERIC_CLOCKEVENTS_BUILD=y @@ -197,6 +203,8 @@ CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y @@ -211,19 +219,20 @@ CONFIG_FLATMEM_MANUAL=y # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set +CONFIG_EXTRA_TARGETS="" CONFIG_PM=y -# CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set CONFIG_SECCOMP=y CONFIG_ISA_DMA_API=y @@ -233,7 +242,7 @@ CONFIG_ISA_DMA_API=y # CONFIG_ZONE_DMA=y CONFIG_GENERIC_ISA_DMA=y -CONFIG_FSL_SOC=y +CONFIG_PPC_PCI_CHOICE=y # CONFIG_PCI is not set # CONFIG_PCI_DOMAINS is not set # CONFIG_PCI_SYSCALL is not set @@ -254,10 +263,6 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0xc0000000 - -# -# Networking -# CONFIG_NET=y # @@ -308,6 +313,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -328,14 +334,8 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -446,6 +446,7 @@ CONFIG_BLK_DEV_RAM_SIZE=32768 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set # CONFIG_MISC_DEVICES is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -487,11 +488,11 @@ CONFIG_CHR_DEV_SG=y # CONFIG_SCSI_SAS_LIBSAS is not set # CONFIG_SCSI_SRP_ATTRS is not set # CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_DH is not set # CONFIG_ATA is not set # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -521,6 +522,9 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set CONFIG_FEC_MPC52xx=y CONFIG_FEC_MPC52xx_MDIO=y @@ -532,7 +536,6 @@ CONFIG_FEC_MPC52xx_MDIO=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI is not set # CONFIG_IWLWIFI_LEDS is not set # @@ -567,6 +570,7 @@ CONFIG_FEC_MPC52xx_MDIO=y # Character devices # # CONFIG_VT is not set +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # @@ -596,25 +600,40 @@ CONFIG_LEGACY_PTY_COUNT=256 CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y # # I2C Hardware Bus support # + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# CONFIG_I2C_MPC=y # CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_TAOS_EVM is not set # CONFIG_I2C_TINY_USB is not set + +# +# Other I2C/SMBus bus drivers +# # CONFIG_I2C_PCA_PLATFORM is not set # # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set +# CONFIG_AT24 is not set # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set @@ -623,10 +642,13 @@ CONFIG_I2C_MPC=y # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set @@ -640,24 +662,39 @@ CONFIG_WATCHDOG=y # USB-based Watchdog Cards # # CONFIG_USBPCWATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_REGULATOR is not set # # Multimedia devices # + +# +# Multimedia core support +# # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# # CONFIG_DAB is not set # @@ -672,10 +709,6 @@ CONFIG_SSB_POSSIBLE=y # Display device support # # CONFIG_DISPLAY_SUPPORT is not set - -# -# Sound -# # CONFIG_SOUND is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y @@ -695,11 +728,16 @@ CONFIG_USB_DEVICEFS=y # CONFIG_USB_OTG is not set # CONFIG_USB_OTG_WHITELIST is not set # CONFIG_USB_OTG_BLACKLIST_HUB is not set +# CONFIG_USB_MON is not set +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set # # USB Host Controller Drivers # +# CONFIG_USB_C67X00_HCD is not set # CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y CONFIG_USB_OHCI_HCD_PPC_SOC=y CONFIG_USB_OHCI_HCD_PPC_OF=y @@ -710,12 +748,16 @@ CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y # CONFIG_USB_OHCI_LITTLE_ENDIAN is not set # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_HWA_HCD is not set +# CONFIG_USB_MUSB_HDRC is not set # # USB Device Class drivers # # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -744,7 +786,6 @@ CONFIG_USB_STORAGE=y # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set -# CONFIG_USB_MON is not set # # USB port drivers @@ -757,7 +798,7 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set -# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_SEVSEG is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set @@ -773,14 +814,19 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set # CONFIG_USB_GADGET is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set # CONFIG_EDAC is not set # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -792,12 +838,13 @@ CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set CONFIG_DNOTIFY=y @@ -830,6 +877,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -860,6 +908,7 @@ CONFIG_JFFS2_RTIME=y CONFIG_CRAMFS=y # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set @@ -870,14 +919,14 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y -# CONFIG_NFSD is not set CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y -# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -953,9 +1002,9 @@ CONFIG_NLS_ISO8859_1=y # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set @@ -982,9 +1031,12 @@ CONFIG_FRAME_WARN=1024 CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 CONFIG_SCHED_DEBUG=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set # CONFIG_SLUB_DEBUG_ON is not set # CONFIG_SLUB_STATS is not set # CONFIG_DEBUG_RT_MUTEXES is not set @@ -998,16 +1050,37 @@ CONFIG_SCHED_DEBUG=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_HAVE_FUNCTION_TRACER=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set -# CONFIG_DEBUGGER is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_MSI_BITMAP_SELFTEST is not set +# CONFIG_XMON is not set # CONFIG_IRQSTACKS is not set # CONFIG_BDI_SWITCH is not set # CONFIG_BOOTX_TEXT is not set @@ -1018,14 +1091,19 @@ CONFIG_SCHED_DEBUG=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y # CONFIG_CRYPTO_GF128MUL is not set # CONFIG_CRYPTO_NULL is not set @@ -1063,6 +1141,10 @@ CONFIG_CRYPTO_PCBC=y # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y # CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set # CONFIG_CRYPTO_SHA1 is not set # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set @@ -1093,6 +1175,11 @@ CONFIG_CRYPTO_DES=y # # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y CONFIG_PPC_CLOCK=y CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/52xx/lite5200b_defconfig b/arch/powerpc/configs/52xx/lite5200b_defconfig index 1a8a250..5b969f9 100644 --- a/arch/powerpc/configs/52xx/lite5200b_defconfig +++ b/arch/powerpc/configs/52xx/lite5200b_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.25 -# Tue Apr 29 07:12:56 2008 +# Linux kernel version: 2.6.28-rc4 +# Thu Nov 13 02:10:16 2008 # # CONFIG_PPC64 is not set @@ -22,7 +22,7 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 -CONFIG_PPC_MERGE=y +# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set CONFIG_MMU=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_GENERIC_TIME=y @@ -32,6 +32,7 @@ CONFIG_GENERIC_HARDIRQS=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y @@ -103,7 +104,9 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y +CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -111,24 +114,30 @@ CONFIG_SLUB=y # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y -CONFIG_PROC_PAGE_MONITOR=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +CONFIG_HAVE_CLK=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set -# CONFIG_KMOD is not set +CONFIG_KMOD=y CONFIG_BLOCK=y # CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -143,19 +152,16 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +CONFIG_FREEZER=y # # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_PPC_82xx is not set -# CONFIG_PPC_83xx is not set -# CONFIG_PPC_86xx is not set CONFIG_CLASSIC32=y # CONFIG_PPC_CHRP is not set -# CONFIG_PPC_MPC512x is not set -# CONFIG_PPC_MPC5121 is not set # CONFIG_MPC5121_ADS is not set +# CONFIG_MPC5121_GENERIC is not set CONFIG_PPC_MPC52xx=y CONFIG_PPC_MPC5200_SIMPLE=y # CONFIG_PPC_EFIKA is not set @@ -165,7 +171,10 @@ CONFIG_PPC_LITE5200=y # CONFIG_PPC_PMAC is not set # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PPC_82xx is not set # CONFIG_PQ2ADS is not set +# CONFIG_PPC_83xx is not set +# CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set # CONFIG_IPIC is not set # CONFIG_MPIC is not set @@ -198,11 +207,13 @@ CONFIG_HZ_250=y # CONFIG_HZ_300 is not set # CONFIG_HZ_1000 is not set CONFIG_HZ=250 -# CONFIG_SCHED_HRTICK is not set +CONFIG_SCHED_HRTICK=y CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y @@ -217,19 +228,20 @@ CONFIG_FLATMEM_MANUAL=y # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set +CONFIG_EXTRA_TARGETS="" CONFIG_PM=y -# CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set CONFIG_PM_SLEEP=y CONFIG_SUSPEND=y @@ -243,7 +255,7 @@ CONFIG_ISA_DMA_API=y CONFIG_ZONE_DMA=y CONFIG_GENERIC_ISA_DMA=y # CONFIG_PPC_INDIRECT_PCI is not set -CONFIG_FSL_SOC=y +CONFIG_PPC_PCI_CHOICE=y CONFIG_PCI=y CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y @@ -269,10 +281,6 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0xc0000000 - -# -# Networking -# CONFIG_NET=y # @@ -323,6 +331,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -343,14 +352,8 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -390,12 +393,16 @@ CONFIG_BLK_DEV_RAM_SIZE=32768 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y # CONFIG_PHANTOM is not set # CONFIG_EEPROM_93CX6 is not set # CONFIG_SGI_IOC4 is not set # CONFIG_TIFM_CORE is not set +# CONFIG_ICS932S401 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_HP_ILO is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -412,7 +419,7 @@ CONFIG_SCSI_DMA=y # # SCSI support type (disk, tape, CD-ROM) # -# CONFIG_BLK_DEV_SD is not set +CONFIG_BLK_DEV_SD=y # CONFIG_CHR_DEV_ST is not set # CONFIG_CHR_DEV_OSST is not set # CONFIG_BLK_DEV_SR is not set @@ -474,12 +481,12 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_DH is not set CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set CONFIG_SATA_PMP=y # CONFIG_SATA_AHCI is not set # CONFIG_SATA_SIL24 is not set -# CONFIG_SATA_FSL is not set CONFIG_ATA_SFF=y # CONFIG_SATA_SVW is not set # CONFIG_ATA_PIIX is not set @@ -535,18 +542,22 @@ CONFIG_PATA_MPC52xx=y # CONFIG_PATA_VIA is not set # CONFIG_PATA_WINBOND is not set # CONFIG_PATA_PLATFORM is not set +# CONFIG_PATA_SCH is not set # CONFIG_MD is not set # CONFIG_FUSION is not set # # IEEE 1394 (FireWire) support # + +# +# Enable only one of the two stacks, unless you know what you are doing +# # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -583,16 +594,19 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set CONFIG_FEC_MPC52xx=y CONFIG_FEC_MPC52xx_MDIO=y +# CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set # CONFIG_E1000E is not set -# CONFIG_E1000E_ENABLED is not set # CONFIG_IP1000 is not set # CONFIG_IGB is not set # CONFIG_NS83820 is not set @@ -605,22 +619,27 @@ CONFIG_NETDEV_1000=y # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set -# CONFIG_GIANFAR is not set # CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set +# CONFIG_ATL1E is not set +# CONFIG_JME is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_ENIC is not set # CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set # CONFIG_NIU is not set +# CONFIG_MLX4_EN is not set # CONFIG_MLX4_CORE is not set # CONFIG_TEHUTI is not set # CONFIG_BNX2X is not set +# CONFIG_QLGE is not set +# CONFIG_SFC is not set # CONFIG_TR is not set # @@ -628,7 +647,6 @@ CONFIG_NETDEV_10000=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI is not set # CONFIG_IWLWIFI_LEDS is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -657,6 +675,7 @@ CONFIG_NETDEV_10000=y # Character devices # # CONFIG_VT is not set +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # CONFIG_NOZOMI is not set @@ -691,42 +710,63 @@ CONFIG_DEVPORT=y CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y # # I2C Hardware Bus support # + +# +# PC SMBus host controller drivers +# # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set # CONFIG_I2C_AMD756 is not set # CONFIG_I2C_AMD8111 is not set # CONFIG_I2C_I801 is not set -# CONFIG_I2C_I810 is not set +# CONFIG_I2C_ISCH is not set # CONFIG_I2C_PIIX4 is not set -CONFIG_I2C_MPC=y # CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_PROSAVAGE is not set -# CONFIG_I2C_SAVAGE4 is not set -# CONFIG_I2C_SIMTEC is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_STUB is not set # CONFIG_I2C_VIA is not set # CONFIG_I2C_VIAPRO is not set + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_MPC=y +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set + +# +# Graphics adapter I2C/DDC channel drivers +# # CONFIG_I2C_VOODOO3 is not set + +# +# Other I2C/SMBus bus drivers +# # CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set # # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set +# CONFIG_AT24 is not set # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set @@ -735,29 +775,47 @@ CONFIG_I2C_MPC=y # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_REGULATOR is not set # # Multimedia devices # + +# +# Multimedia core support +# # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# # CONFIG_DAB is not set # @@ -774,10 +832,6 @@ CONFIG_VIDEO_OUTPUT_CONTROL=m # Display device support # # CONFIG_DISPLAY_SUPPORT is not set - -# -# Sound -# # CONFIG_SOUND is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y @@ -788,17 +842,25 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB_OTG_BLACKLIST_HUB is not set # +# Enable Host or Gadget support to see Inventra options +# + +# # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' # # CONFIG_USB_GADGET is not set +# CONFIG_UWB is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set # CONFIG_INFINIBAND is not set # CONFIG_EDAC is not set # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -810,12 +872,13 @@ CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set CONFIG_DNOTIFY=y @@ -845,6 +908,7 @@ CONFIG_INOTIFY_USER=y CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -864,6 +928,7 @@ CONFIG_TMPFS=y # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set @@ -874,14 +939,14 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y -# CONFIG_NFSD is not set CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y -# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -902,9 +967,9 @@ CONFIG_MSDOS_PARTITION=y # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set @@ -929,9 +994,12 @@ CONFIG_FRAME_WARN=1024 CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 CONFIG_SCHED_DEBUG=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set # CONFIG_SLUB_DEBUG_ON is not set # CONFIG_SLUB_STATS is not set # CONFIG_DEBUG_RT_MUTEXES is not set @@ -945,17 +1013,37 @@ CONFIG_SCHED_DEBUG=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_HAVE_FUNCTION_TRACER=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set -# CONFIG_DEBUGGER is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_MSI_BITMAP_SELFTEST is not set +# CONFIG_XMON is not set # CONFIG_IRQSTACKS is not set # CONFIG_BDI_SWITCH is not set # CONFIG_BOOTX_TEXT is not set @@ -966,14 +1054,19 @@ CONFIG_DEBUG_INFO=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y # CONFIG_CRYPTO_GF128MUL is not set # CONFIG_CRYPTO_NULL is not set @@ -1012,6 +1105,10 @@ CONFIG_CRYPTO_CBC=y # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y # CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set # CONFIG_CRYPTO_SHA1 is not set # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set @@ -1042,6 +1139,11 @@ CONFIG_CRYPTO_DES=y # # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y # CONFIG_CRYPTO_DEV_HIFN_795X is not set CONFIG_PPC_CLOCK=y diff --git a/arch/powerpc/configs/52xx/motionpro_defconfig b/arch/powerpc/configs/52xx/motionpro_defconfig index 8c7ba7c..3c0d4e5 100644 --- a/arch/powerpc/configs/52xx/motionpro_defconfig +++ b/arch/powerpc/configs/52xx/motionpro_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.25 -# Tue Apr 29 07:12:22 2008 +# Linux kernel version: 2.6.28-rc4 +# Thu Nov 13 02:11:02 2008 # # CONFIG_PPC64 is not set @@ -22,7 +22,7 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 -CONFIG_PPC_MERGE=y +# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set CONFIG_MMU=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_GENERIC_TIME=y @@ -32,6 +32,7 @@ CONFIG_GENERIC_HARDIRQS=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y @@ -102,6 +103,7 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLUB_DEBUG=y # CONFIG_SLAB is not set @@ -110,9 +112,13 @@ CONFIG_SLUB=y # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y -CONFIG_PROC_PAGE_MONITOR=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +CONFIG_HAVE_CLK=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set @@ -123,6 +129,7 @@ CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -137,19 +144,16 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_PPC_82xx is not set -# CONFIG_PPC_83xx is not set -# CONFIG_PPC_86xx is not set CONFIG_CLASSIC32=y # CONFIG_PPC_CHRP is not set -# CONFIG_PPC_MPC512x is not set -# CONFIG_PPC_MPC5121 is not set # CONFIG_MPC5121_ADS is not set +# CONFIG_MPC5121_GENERIC is not set CONFIG_PPC_MPC52xx=y CONFIG_PPC_MPC5200_SIMPLE=y # CONFIG_PPC_EFIKA is not set @@ -159,7 +163,10 @@ CONFIG_PPC_MPC5200_SIMPLE=y # CONFIG_PPC_PMAC is not set # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PPC_82xx is not set # CONFIG_PQ2ADS is not set +# CONFIG_PPC_83xx is not set +# CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set # CONFIG_IPIC is not set # CONFIG_MPIC is not set @@ -183,7 +190,6 @@ CONFIG_PPC_BESTCOMM_FEC=y # Kernel options # # CONFIG_HIGHMEM is not set -# CONFIG_TICK_ONESHOT is not set # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set CONFIG_GENERIC_CLOCKEVENTS_BUILD=y @@ -197,6 +203,8 @@ CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y @@ -211,19 +219,20 @@ CONFIG_FLATMEM_MANUAL=y # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set +CONFIG_EXTRA_TARGETS="" CONFIG_PM=y -# CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set CONFIG_SECCOMP=y CONFIG_ISA_DMA_API=y @@ -233,7 +242,7 @@ CONFIG_ISA_DMA_API=y # CONFIG_ZONE_DMA=y CONFIG_GENERIC_ISA_DMA=y -CONFIG_FSL_SOC=y +CONFIG_PPC_PCI_CHOICE=y # CONFIG_PCI is not set # CONFIG_PCI_DOMAINS is not set # CONFIG_PCI_SYSCALL is not set @@ -254,10 +263,6 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0xc0000000 - -# -# Networking -# CONFIG_NET=y # @@ -308,6 +313,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -328,14 +334,8 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -445,9 +445,12 @@ CONFIG_BLK_DEV_RAM_SIZE=32768 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set +# CONFIG_ICS932S401 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -490,10 +493,10 @@ CONFIG_CHR_DEV_SG=y CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set CONFIG_SATA_PMP=y -# CONFIG_SATA_FSL is not set CONFIG_ATA_SFF=y # CONFIG_SATA_MV is not set CONFIG_PATA_MPC52xx=y @@ -501,7 +504,6 @@ CONFIG_PATA_MPC52xx=y # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -531,6 +533,9 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set CONFIG_FEC_MPC52xx=y CONFIG_FEC_MPC52xx_MDIO=y @@ -542,7 +547,6 @@ CONFIG_FEC_MPC52xx_MDIO=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI is not set # CONFIG_IWLWIFI_LEDS is not set # CONFIG_WAN is not set # CONFIG_PPP is not set @@ -568,6 +572,7 @@ CONFIG_FEC_MPC52xx_MDIO=y # Character devices # # CONFIG_VT is not set +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # @@ -596,24 +601,39 @@ CONFIG_LEGACY_PTY_COUNT=256 CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y # # I2C Hardware Bus support # + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# CONFIG_I2C_MPC=y # CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_TAOS_EVM is not set + +# +# Other I2C/SMBus bus drivers +# # CONFIG_I2C_PCA_PLATFORM is not set # # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set +# CONFIG_AT24 is not set CONFIG_SENSORS_EEPROM=y # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set @@ -622,10 +642,13 @@ CONFIG_SENSORS_EEPROM=y # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_AD7414 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -633,6 +656,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7462 is not set # CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ADT7473 is not set # CONFIG_SENSORS_ATXP1 is not set @@ -675,6 +699,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set @@ -683,24 +708,39 @@ CONFIG_WATCHDOG=y # # CONFIG_SOFT_WATCHDOG is not set # CONFIG_MPC5200_WDT is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_REGULATOR is not set # # Multimedia devices # + +# +# Multimedia core support +# # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# CONFIG_DAB=y # @@ -715,10 +755,6 @@ CONFIG_DAB=y # Display device support # # CONFIG_DISPLAY_SUPPORT is not set - -# -# Sound -# # CONFIG_SOUND is not set # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set @@ -729,6 +765,7 @@ CONFIG_LEDS_CLASS=y # # LED drivers # +# CONFIG_LEDS_PCA955X is not set # # LED Triggers @@ -736,7 +773,9 @@ CONFIG_LEDS_CLASS=y CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=y # CONFIG_LEDS_TRIGGER_HEARTBEAT is not set +# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set # CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set +# CONFIG_ACCESSIBILITY is not set # CONFIG_EDAC is not set CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y @@ -767,6 +806,8 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_M41T80 is not set # CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set # # SPI RTC drivers @@ -776,19 +817,25 @@ CONFIG_RTC_DRV_DS1307=y # Platform RTC drivers # # CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1286 is not set # CONFIG_RTC_DRV_DS1511 is not set # CONFIG_RTC_DRV_DS1553 is not set # CONFIG_RTC_DRV_DS1742 is not set # CONFIG_RTC_DRV_STK17TA8 is not set # CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set # CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set # CONFIG_RTC_DRV_V3020 is not set # # on-CPU RTC drivers # +# CONFIG_RTC_DRV_PPC is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -800,12 +847,13 @@ CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set CONFIG_DNOTIFY=y @@ -838,6 +886,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -868,6 +917,7 @@ CONFIG_JFFS2_RTIME=y CONFIG_CRAMFS=y # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set @@ -878,14 +928,14 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y -# CONFIG_NFSD is not set CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y -# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -961,9 +1011,9 @@ CONFIG_NLS_ISO8859_1=y # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set @@ -990,9 +1040,12 @@ CONFIG_FRAME_WARN=1024 CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 CONFIG_SCHED_DEBUG=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set # CONFIG_SLUB_DEBUG_ON is not set # CONFIG_SLUB_STATS is not set # CONFIG_DEBUG_RT_MUTEXES is not set @@ -1006,16 +1059,37 @@ CONFIG_SCHED_DEBUG=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_HAVE_FUNCTION_TRACER=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set -# CONFIG_DEBUGGER is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_MSI_BITMAP_SELFTEST is not set +# CONFIG_XMON is not set # CONFIG_IRQSTACKS is not set # CONFIG_BDI_SWITCH is not set # CONFIG_BOOTX_TEXT is not set @@ -1026,14 +1100,19 @@ CONFIG_DEBUG_INFO=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y # CONFIG_CRYPTO_GF128MUL is not set # CONFIG_CRYPTO_NULL is not set @@ -1071,6 +1150,10 @@ CONFIG_CRYPTO_PCBC=y # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y # CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set # CONFIG_CRYPTO_SHA1 is not set # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set @@ -1101,6 +1184,11 @@ CONFIG_CRYPTO_DES=y # # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y CONFIG_PPC_CLOCK=y CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/52xx/pcm030_defconfig b/arch/powerpc/configs/52xx/pcm030_defconfig index 9c0caa4..9d02077 100644 --- a/arch/powerpc/configs/52xx/pcm030_defconfig +++ b/arch/powerpc/configs/52xx/pcm030_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.25 -# Tue Apr 29 07:13:19 2008 +# Linux kernel version: 2.6.28-rc4 +# Thu Nov 13 02:13:16 2008 # # CONFIG_PPC64 is not set @@ -22,7 +22,7 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 -CONFIG_PPC_MERGE=y +# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set CONFIG_MMU=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_GENERIC_TIME=y @@ -32,6 +32,7 @@ CONFIG_GENERIC_HARDIRQS=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y @@ -104,7 +105,9 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y # CONFIG_VM_EVENT_COUNTERS is not set +CONFIG_PCI_QUIRKS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set @@ -112,24 +115,30 @@ CONFIG_SLAB=y # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y # CONFIG_KPROBES is not set +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y -CONFIG_PROC_PAGE_MONITOR=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +CONFIG_HAVE_CLK=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set -# CONFIG_KMOD is not set +CONFIG_KMOD=y CONFIG_BLOCK=y # CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -144,19 +153,16 @@ CONFIG_IOSCHED_NOOP=y CONFIG_DEFAULT_NOOP=y CONFIG_DEFAULT_IOSCHED="noop" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_PPC_82xx is not set -# CONFIG_PPC_83xx is not set -# CONFIG_PPC_86xx is not set CONFIG_CLASSIC32=y # CONFIG_PPC_CHRP is not set -# CONFIG_PPC_MPC512x is not set -# CONFIG_PPC_MPC5121 is not set # CONFIG_MPC5121_ADS is not set +# CONFIG_MPC5121_GENERIC is not set CONFIG_PPC_MPC52xx=y CONFIG_PPC_MPC5200_SIMPLE=y # CONFIG_PPC_EFIKA is not set @@ -166,7 +172,10 @@ CONFIG_PPC_MPC5200_SIMPLE=y # CONFIG_PPC_PMAC is not set # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PPC_82xx is not set # CONFIG_PQ2ADS is not set +# CONFIG_PPC_83xx is not set +# CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set # CONFIG_IPIC is not set # CONFIG_MPIC is not set @@ -199,12 +208,14 @@ CONFIG_HZ_100=y # CONFIG_HZ_300 is not set # CONFIG_HZ_1000 is not set CONFIG_HZ=100 -# CONFIG_SCHED_HRTICK is not set +CONFIG_SCHED_HRTICK=y # CONFIG_PREEMPT_NONE is not set # CONFIG_PREEMPT_VOLUNTARY is not set CONFIG_PREEMPT=y # CONFIG_PREEMPT_RCU is not set CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y @@ -219,17 +230,19 @@ CONFIG_FLATMEM_MANUAL=y # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set +CONFIG_EXTRA_TARGETS="" # CONFIG_PM is not set # CONFIG_SECCOMP is not set CONFIG_ISA_DMA_API=y @@ -240,7 +253,7 @@ CONFIG_ISA_DMA_API=y CONFIG_ZONE_DMA=y CONFIG_GENERIC_ISA_DMA=y # CONFIG_PPC_INDIRECT_PCI is not set -CONFIG_FSL_SOC=y +CONFIG_PPC_PCI_CHOICE=y CONFIG_PCI=y CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y @@ -265,10 +278,6 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0xc0000000 - -# -# Networking -# CONFIG_NET=y # @@ -313,6 +322,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -333,14 +343,8 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -484,12 +488,12 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SAS_LIBSAS is not set # CONFIG_SCSI_SRP_ATTRS is not set # CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_DH is not set CONFIG_ATA=m # CONFIG_ATA_NONSTANDARD is not set CONFIG_SATA_PMP=y # CONFIG_SATA_AHCI is not set # CONFIG_SATA_SIL24 is not set -# CONFIG_SATA_FSL is not set CONFIG_ATA_SFF=y # CONFIG_SATA_SVW is not set # CONFIG_ATA_PIIX is not set @@ -545,18 +549,22 @@ CONFIG_PATA_MPC52xx=m # CONFIG_PATA_VIA is not set # CONFIG_PATA_WINBOND is not set # CONFIG_PATA_PLATFORM is not set +# CONFIG_PATA_SCH is not set # CONFIG_MD is not set # CONFIG_FUSION is not set # # IEEE 1394 (FireWire) support # + +# +# Enable only one of the two stacks, unless you know what you are doing +# # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -593,10 +601,14 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set CONFIG_FEC_MPC52xx=y CONFIG_FEC_MPC52xx_MDIO=y +# CONFIG_ATL2 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set # CONFIG_TR is not set @@ -606,7 +618,6 @@ CONFIG_FEC_MPC52xx_MDIO=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI is not set # CONFIG_IWLWIFI_LEDS is not set # @@ -644,6 +655,7 @@ CONFIG_FEC_MPC52xx_MDIO=y # Character devices # # CONFIG_VT is not set +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # CONFIG_NOZOMI is not set @@ -675,43 +687,64 @@ CONFIG_DEVPORT=y CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y # # I2C Hardware Bus support # + +# +# PC SMBus host controller drivers +# # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set # CONFIG_I2C_AMD756 is not set # CONFIG_I2C_AMD8111 is not set # CONFIG_I2C_I801 is not set -# CONFIG_I2C_I810 is not set +# CONFIG_I2C_ISCH is not set # CONFIG_I2C_PIIX4 is not set -CONFIG_I2C_MPC=y # CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_PROSAVAGE is not set -# CONFIG_I2C_SAVAGE4 is not set -# CONFIG_I2C_SIMTEC is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_STUB is not set -# CONFIG_I2C_TINY_USB is not set # CONFIG_I2C_VIA is not set # CONFIG_I2C_VIAPRO is not set + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_MPC=y +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Graphics adapter I2C/DDC channel drivers +# # CONFIG_I2C_VOODOO3 is not set + +# +# Other I2C/SMBus bus drivers +# # CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set # # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set +# CONFIG_AT24 is not set CONFIG_SENSORS_EEPROM=m # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set @@ -720,29 +753,47 @@ CONFIG_SENSORS_EEPROM=m # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_REGULATOR is not set # # Multimedia devices # + +# +# Multimedia core support +# # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# # CONFIG_DAB is not set # @@ -759,10 +810,6 @@ CONFIG_SSB_POSSIBLE=y # Display device support # # CONFIG_DISPLAY_SUPPORT is not set - -# -# Sound -# # CONFIG_SOUND is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y @@ -781,12 +828,17 @@ CONFIG_USB_DEVICEFS=y # CONFIG_USB_OTG is not set # CONFIG_USB_OTG_WHITELIST is not set # CONFIG_USB_OTG_BLACKLIST_HUB is not set +# CONFIG_USB_MON is not set +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set # # USB Host Controller Drivers # +# CONFIG_USB_C67X00_HCD is not set # CONFIG_USB_EHCI_HCD is not set # CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=m # CONFIG_USB_OHCI_HCD_PPC_SOC is not set CONFIG_USB_OHCI_HCD_PPC_OF=y @@ -799,12 +851,17 @@ CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y # CONFIG_USB_UHCI_HCD is not set # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_WHCI_HCD is not set +# CONFIG_USB_HWA_HCD is not set +# CONFIG_USB_MUSB_HDRC is not set # # USB Device Class drivers # # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -833,7 +890,6 @@ CONFIG_USB_STORAGE=m # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set -# CONFIG_USB_MON is not set # # USB port drivers @@ -846,7 +902,7 @@ CONFIG_USB_STORAGE=m # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set -# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_SEVSEG is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set @@ -862,10 +918,14 @@ CONFIG_USB_STORAGE=m # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set # CONFIG_USB_GADGET is not set +# CONFIG_UWB is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set # CONFIG_INFINIBAND is not set # CONFIG_EDAC is not set CONFIG_RTC_LIB=m @@ -894,6 +954,8 @@ CONFIG_RTC_DRV_PCF8563=m # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_M41T80 is not set # CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set # # SPI RTC drivers @@ -903,19 +965,25 @@ CONFIG_RTC_DRV_PCF8563=m # Platform RTC drivers # # CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1286 is not set # CONFIG_RTC_DRV_DS1511 is not set # CONFIG_RTC_DRV_DS1553 is not set # CONFIG_RTC_DRV_DS1742 is not set # CONFIG_RTC_DRV_STK17TA8 is not set # CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set # CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set # CONFIG_RTC_DRV_V3020 is not set # # on-CPU RTC drivers # +# CONFIG_RTC_DRV_PPC is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -927,12 +995,13 @@ CONFIG_EXT3_FS=m CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=m CONFIG_FS_MBCACHE=m # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_DNOTIFY is not set @@ -964,6 +1033,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y # CONFIG_PROC_KCORE is not set CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -994,6 +1064,7 @@ CONFIG_JFFS2_RTIME=y # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set @@ -1004,13 +1075,13 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set -# CONFIG_NFSD is not set CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y -# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_SUNRPC_REGISTER_V4 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -1070,9 +1141,9 @@ CONFIG_NLS_ISO8859_1=y # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set @@ -1098,7 +1169,17 @@ CONFIG_FRAME_WARN=1024 # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set # CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_LATENCYTOP is not set +CONFIG_HAVE_FUNCTION_TRACER=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y # CONFIG_IRQSTACKS is not set # CONFIG_BOOTX_TEXT is not set # CONFIG_PPC_EARLY_DEBUG is not set @@ -1108,6 +1189,7 @@ CONFIG_FRAME_WARN=1024 # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set CONFIG_PPC_CLOCK=y diff --git a/arch/powerpc/configs/52xx/tqm5200_defconfig b/arch/powerpc/configs/52xx/tqm5200_defconfig index 7672bfb..bc19005 100644 --- a/arch/powerpc/configs/52xx/tqm5200_defconfig +++ b/arch/powerpc/configs/52xx/tqm5200_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.25 -# Tue Apr 29 07:12:39 2008 +# Linux kernel version: 2.6.28-rc4 +# Thu Nov 13 02:09:30 2008 # # CONFIG_PPC64 is not set @@ -22,7 +22,7 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 -CONFIG_PPC_MERGE=y +# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set CONFIG_MMU=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_GENERIC_TIME=y @@ -32,6 +32,7 @@ CONFIG_GENERIC_HARDIRQS=y # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y @@ -102,6 +103,7 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLUB_DEBUG=y # CONFIG_SLAB is not set @@ -110,14 +112,19 @@ CONFIG_SLUB=y # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y -CONFIG_PROC_PAGE_MONITOR=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +CONFIG_HAVE_CLK=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y @@ -128,6 +135,7 @@ CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -142,19 +150,16 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_PPC_82xx is not set -# CONFIG_PPC_83xx is not set -# CONFIG_PPC_86xx is not set CONFIG_CLASSIC32=y # CONFIG_PPC_CHRP is not set -# CONFIG_PPC_MPC512x is not set -# CONFIG_PPC_MPC5121 is not set # CONFIG_MPC5121_ADS is not set +# CONFIG_MPC5121_GENERIC is not set CONFIG_PPC_MPC52xx=y CONFIG_PPC_MPC5200_SIMPLE=y # CONFIG_PPC_EFIKA is not set @@ -164,7 +169,10 @@ CONFIG_PPC_MPC5200_BUGFIX=y # CONFIG_PPC_PMAC is not set # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PPC_82xx is not set # CONFIG_PQ2ADS is not set +# CONFIG_PPC_83xx is not set +# CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set # CONFIG_IPIC is not set # CONFIG_MPIC is not set @@ -188,7 +196,6 @@ CONFIG_PPC_BESTCOMM_FEC=y # Kernel options # # CONFIG_HIGHMEM is not set -# CONFIG_TICK_ONESHOT is not set # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set CONFIG_GENERIC_CLOCKEVENTS_BUILD=y @@ -202,6 +209,8 @@ CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set # CONFIG_IOMMU_HELPER is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y @@ -216,19 +225,20 @@ CONFIG_FLATMEM_MANUAL=y # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set +CONFIG_EXTRA_TARGETS="" CONFIG_PM=y -# CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set CONFIG_SECCOMP=y CONFIG_ISA_DMA_API=y @@ -238,7 +248,7 @@ CONFIG_ISA_DMA_API=y # CONFIG_ZONE_DMA=y CONFIG_GENERIC_ISA_DMA=y -CONFIG_FSL_SOC=y +CONFIG_PPC_PCI_CHOICE=y # CONFIG_PCI is not set # CONFIG_PCI_DOMAINS is not set # CONFIG_PCI_SYSCALL is not set @@ -259,10 +269,6 @@ CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0xc0000000 - -# -# Networking -# CONFIG_NET=y # @@ -313,6 +319,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -333,14 +340,8 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -451,6 +452,7 @@ CONFIG_BLK_DEV_RAM_SIZE=32768 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set # CONFIG_MISC_DEVICES is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -495,10 +497,10 @@ CONFIG_SCSI_WAIT_SCAN=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set CONFIG_SATA_PMP=y -# CONFIG_SATA_FSL is not set CONFIG_ATA_SFF=y # CONFIG_SATA_MV is not set CONFIG_PATA_MPC52xx=y @@ -507,7 +509,6 @@ CONFIG_PATA_PLATFORM=y # CONFIG_MD is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set @@ -537,6 +538,9 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set CONFIG_FEC_MPC52xx=y CONFIG_FEC_MPC52xx_MDIO=y @@ -548,7 +552,6 @@ CONFIG_FEC_MPC52xx_MDIO=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set -# CONFIG_IWLWIFI is not set # CONFIG_IWLWIFI_LEDS is not set # @@ -583,6 +586,7 @@ CONFIG_FEC_MPC52xx_MDIO=y # Character devices # # CONFIG_VT is not set +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # @@ -611,26 +615,41 @@ CONFIG_LEGACY_PTY_COUNT=256 CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y # # I2C Hardware Bus support # + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# CONFIG_I2C_MPC=y # CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_STUB is not set # CONFIG_I2C_TINY_USB is not set + +# +# Other I2C/SMBus bus drivers +# # CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set # # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set +# CONFIG_AT24 is not set # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set @@ -639,10 +658,13 @@ CONFIG_I2C_MPC=y # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_AD7414 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -650,6 +672,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7462 is not set # CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ADT7473 is not set # CONFIG_SENSORS_ATXP1 is not set @@ -692,6 +715,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set # CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set @@ -705,24 +729,39 @@ CONFIG_WATCHDOG=y # USB-based Watchdog Cards # # CONFIG_USBPCWATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_REGULATOR is not set # # Multimedia devices # + +# +# Multimedia core support +# # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# # CONFIG_DAB is not set # @@ -737,10 +776,6 @@ CONFIG_SSB_POSSIBLE=y # Display device support # # CONFIG_DISPLAY_SUPPORT is not set - -# -# Sound -# # CONFIG_SOUND is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y @@ -760,11 +795,16 @@ CONFIG_USB_DEVICEFS=y # CONFIG_USB_OTG is not set # CONFIG_USB_OTG_WHITELIST is not set # CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=y +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set # # USB Host Controller Drivers # +# CONFIG_USB_C67X00_HCD is not set # CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y CONFIG_USB_OHCI_HCD_PPC_SOC=y CONFIG_USB_OHCI_HCD_PPC_OF=y @@ -775,12 +815,16 @@ CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y # CONFIG_USB_OHCI_LITTLE_ENDIAN is not set # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_HWA_HCD is not set +# CONFIG_USB_MUSB_HDRC is not set # # USB Device Class drivers # # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -809,7 +853,6 @@ CONFIG_USB_STORAGE=y # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set -CONFIG_USB_MON=y # # USB port drivers @@ -822,7 +865,7 @@ CONFIG_USB_MON=y # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set -# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_SEVSEG is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set @@ -838,10 +881,13 @@ CONFIG_USB_MON=y # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set # CONFIG_USB_GADGET is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set # CONFIG_EDAC is not set CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y @@ -872,6 +918,8 @@ CONFIG_RTC_DRV_DS1307=y # CONFIG_RTC_DRV_PCF8583 is not set # CONFIG_RTC_DRV_M41T80 is not set # CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set # # SPI RTC drivers @@ -881,19 +929,25 @@ CONFIG_RTC_DRV_DS1307=y # Platform RTC drivers # # CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1286 is not set # CONFIG_RTC_DRV_DS1511 is not set # CONFIG_RTC_DRV_DS1553 is not set # CONFIG_RTC_DRV_DS1742 is not set # CONFIG_RTC_DRV_STK17TA8 is not set # CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set # CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set # CONFIG_RTC_DRV_V3020 is not set # # on-CPU RTC drivers # +# CONFIG_RTC_DRV_PPC is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -905,12 +959,13 @@ CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set CONFIG_DNOTIFY=y @@ -943,6 +998,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -973,6 +1029,7 @@ CONFIG_JFFS2_RTIME=y CONFIG_CRAMFS=y # CONFIG_VXFS_FS is not set # CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_ROMFS_FS is not set @@ -983,14 +1040,14 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y -# CONFIG_NFSD is not set CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y -# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -1066,9 +1123,9 @@ CONFIG_NLS_ISO8859_1=y # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set @@ -1095,9 +1152,12 @@ CONFIG_FRAME_WARN=1024 CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 CONFIG_SCHED_DEBUG=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set # CONFIG_SLUB_DEBUG_ON is not set # CONFIG_SLUB_STATS is not set # CONFIG_DEBUG_RT_MUTEXES is not set @@ -1111,17 +1171,37 @@ CONFIG_SCHED_DEBUG=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_HAVE_FUNCTION_TRACER=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set -# CONFIG_DEBUGGER is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_MSI_BITMAP_SELFTEST is not set +# CONFIG_XMON is not set # CONFIG_IRQSTACKS is not set # CONFIG_BDI_SWITCH is not set # CONFIG_BOOTX_TEXT is not set @@ -1132,14 +1212,19 @@ CONFIG_DEBUG_INFO=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y # CONFIG_CRYPTO_GF128MUL is not set # CONFIG_CRYPTO_NULL is not set @@ -1178,6 +1263,10 @@ CONFIG_CRYPTO_PCBC=y # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y # CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set # CONFIG_CRYPTO_SHA1 is not set # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set @@ -1208,6 +1297,11 @@ CONFIG_CRYPTO_DES=y # # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y CONFIG_PPC_CLOCK=y CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/mpc5200_defconfig b/arch/powerpc/configs/mpc5200_defconfig index 740c9f2..15c5604 100644 --- a/arch/powerpc/configs/mpc5200_defconfig +++ b/arch/powerpc/configs/mpc5200_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.24-rc6 -# Fri Jan 18 14:19:54 2008 +# Linux kernel version: 2.6.28-rc4 +# Thu Nov 13 02:09:07 2008 # # CONFIG_PPC64 is not set @@ -22,14 +22,18 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_SMP is not set CONFIG_PPC32=y CONFIG_WORD_SIZE=32 -CONFIG_PPC_MERGE=y +# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set CONFIG_MMU=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y +# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y @@ -47,7 +51,8 @@ CONFIG_OF=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y -# CONFIG_DEFAULT_UIMAGE is not set +CONFIG_DEFAULT_UIMAGE=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y # CONFIG_PPC_DCR_NATIVE is not set # CONFIG_PPC_DCR_MMIO is not set CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -66,17 +71,15 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set -# CONFIG_USER_NS is not set -# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 # CONFIG_CGROUPS is not set -CONFIG_FAIR_GROUP_SCHED=y -CONFIG_FAIR_USER_SCHED=y -# CONFIG_FAIR_CGROUP_SCHED is not set +# CONFIG_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y # CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set @@ -88,32 +91,49 @@ CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y +CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y # CONFIG_SLAB is not set CONFIG_SLUB=y # CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +CONFIG_HAVE_CLK=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set -# CONFIG_KMOD is not set +CONFIG_KMOD=y CONFIG_BLOCK=y # CONFIG_LBD is not set # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -127,29 +147,34 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_CLASSIC_RCU=y +CONFIG_FREEZER=y # # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_PPC_82xx is not set -# CONFIG_PPC_83xx is not set -# CONFIG_PPC_86xx is not set CONFIG_CLASSIC32=y # CONFIG_PPC_CHRP is not set +# CONFIG_MPC5121_ADS is not set +# CONFIG_MPC5121_GENERIC is not set CONFIG_PPC_MPC52xx=y -CONFIG_PPC_MPC5200=y -CONFIG_PPC_MPC5200_BUGFIX=y CONFIG_PPC_MPC5200_SIMPLE=y CONFIG_PPC_EFIKA=y CONFIG_PPC_LITE5200=y +CONFIG_PPC_MPC5200_BUGFIX=y +# CONFIG_PPC_MPC5200_GPIO is not set # CONFIG_PPC_PMAC is not set # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PPC_82xx is not set # CONFIG_PQ2ADS is not set +# CONFIG_PPC_83xx is not set +# CONFIG_PPC_86xx is not set # CONFIG_EMBEDDED6xx is not set CONFIG_PPC_NATIVE=y # CONFIG_UDBG_RTAS_CONSOLE is not set +# CONFIG_IPIC is not set # CONFIG_MPIC is not set # CONFIG_MPIC_WEIRD is not set # CONFIG_PPC_I8259 is not set @@ -163,7 +188,6 @@ CONFIG_RTAS_PROC=y # CONFIG_GENERIC_IOMAP is not set # CONFIG_CPU_FREQ is not set # CONFIG_TAU is not set -# CONFIG_CPM2 is not set # CONFIG_FSL_ULI1575 is not set CONFIG_PPC_BESTCOMM=y CONFIG_PPC_BESTCOMM_ATA=y @@ -183,12 +207,18 @@ CONFIG_HZ_250=y # CONFIG_HZ_300 is not set # CONFIG_HZ_1000 is not set CONFIG_HZ=250 +CONFIG_SCHED_HRTICK=y CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set +# CONFIG_IOMMU_HELPER is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_HAS_WALK_MEMORY=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y # CONFIG_KEXEC is not set CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y @@ -198,26 +228,25 @@ CONFIG_FLATMEM_MANUAL=y # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y +CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set +CONFIG_EXTRA_TARGETS="" CONFIG_PM=y -# CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set CONFIG_PM_SLEEP=y -CONFIG_SUSPEND_UP_POSSIBLE=y CONFIG_SUSPEND=y -CONFIG_HIBERNATION_UP_POSSIBLE=y -# CONFIG_HIBERNATION is not set +CONFIG_SUSPEND_FREEZER=y CONFIG_SECCOMP=y -CONFIG_WANT_DEVICE_TREE=y -CONFIG_DEVICE_TREE="" CONFIG_ISA_DMA_API=y # @@ -226,7 +255,7 @@ CONFIG_ISA_DMA_API=y CONFIG_ZONE_DMA=y CONFIG_GENERIC_ISA_DMA=y # CONFIG_PPC_INDIRECT_PCI is not set -CONFIG_FSL_SOC=y +CONFIG_PPC_PCI_CHOICE=y CONFIG_PCI=y CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y @@ -237,6 +266,7 @@ CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set +# CONFIG_HAS_RAPIDIO is not set # # Advanced setup @@ -246,15 +276,11 @@ CONFIG_PCI_LEGACY=y # # Default settings for advanced configuration options are used # -CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_PAGE_OFFSET=0xc0000000 CONFIG_KERNEL_START=0xc0000000 +CONFIG_PHYSICAL_START=0x00000000 CONFIG_TASK_SIZE=0xc0000000 -CONFIG_BOOT_LOAD=0x00800000 - -# -# Networking -# CONFIG_NET=y # @@ -267,6 +293,7 @@ CONFIG_XFRM=y CONFIG_XFRM_USER=m # CONFIG_XFRM_SUB_POLICY is not set # CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y @@ -297,8 +324,6 @@ CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set # CONFIG_IPV6 is not set -# CONFIG_INET6_XFRM_TUNNEL is not set -# CONFIG_INET6_TUNNEL is not set # CONFIG_NETWORK_SECMARK is not set # CONFIG_NETFILTER is not set # CONFIG_IP_DCCP is not set @@ -306,6 +331,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -322,17 +348,12 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -357,6 +378,8 @@ CONFIG_MTD_CONCAT=y CONFIG_MTD_PARTITIONS=y # CONFIG_MTD_REDBOOT_PARTS is not set CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_OF_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set # # User Modules And Translation Layers @@ -428,6 +451,7 @@ CONFIG_MTD_PHYSMAP_OF=y # # CONFIG_MTD_UBI is not set CONFIG_OF_DEVICE=y +CONFIG_OF_I2C=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -444,14 +468,20 @@ CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=32768 -CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y # CONFIG_PHANTOM is not set # CONFIG_EEPROM_93CX6 is not set # CONFIG_SGI_IOC4 is not set # CONFIG_TIFM_CORE is not set +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_HP_ILO is not set +# CONFIG_C2PORT is not set +CONFIG_HAVE_IDE=y # CONFIG_IDE is not set # @@ -516,6 +546,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set @@ -528,9 +559,13 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_DH is not set CONFIG_ATA=y # CONFIG_ATA_NONSTANDARD is not set +CONFIG_SATA_PMP=y # CONFIG_SATA_AHCI is not set +# CONFIG_SATA_SIL24 is not set +CONFIG_ATA_SFF=y # CONFIG_SATA_SVW is not set # CONFIG_ATA_PIIX is not set # CONFIG_SATA_MV is not set @@ -540,7 +575,6 @@ CONFIG_ATA=y # CONFIG_SATA_PROMISE is not set # CONFIG_SATA_SX4 is not set # CONFIG_SATA_SIL is not set -# CONFIG_SATA_SIL24 is not set # CONFIG_SATA_SIS is not set # CONFIG_SATA_ULI is not set # CONFIG_SATA_VIA is not set @@ -570,6 +604,7 @@ CONFIG_PATA_MPC52xx=y # CONFIG_PATA_MPIIX is not set # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set +# CONFIG_PATA_NINJA32 is not set # CONFIG_PATA_NS87410 is not set # CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set @@ -586,25 +621,28 @@ CONFIG_PATA_MPC52xx=y # CONFIG_PATA_WINBOND is not set CONFIG_PATA_PLATFORM=y # CONFIG_PATA_OF_PLATFORM is not set +# CONFIG_PATA_SCH is not set # CONFIG_MD is not set # CONFIG_FUSION is not set # # IEEE 1394 (FireWire) support # + +# +# Enable only one of the two stacks, unless you know what you are doing +# # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set # CONFIG_MACINTOSH_DRIVERS is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_DUMMY is not set # CONFIG_BONDING is not set # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set # CONFIG_VETH is not set -# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -620,6 +658,7 @@ CONFIG_PHYLIB=y # CONFIG_SMSC_PHY is not set # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set # CONFIG_FIXED_PHY is not set # CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y @@ -634,10 +673,14 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set CONFIG_FEC_MPC52xx=y CONFIG_FEC_MPC52xx_MDIO=y +# CONFIG_ATL2 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set # CONFIG_TR is not set @@ -647,6 +690,7 @@ CONFIG_FEC_MPC52xx_MDIO=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set # # USB Network Adapters @@ -662,7 +706,6 @@ CONFIG_FEC_MPC52xx_MDIO=y # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NET_FC is not set -# CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set @@ -672,7 +715,30 @@ CONFIG_FEC_MPC52xx_MDIO=y # # Input device support # -# CONFIG_INPUT is not set +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set # # Hardware I/O ports @@ -683,8 +749,14 @@ CONFIG_FEC_MPC52xx_MDIO=y # # Character devices # -# CONFIG_VT is not set +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set # # Serial drivers @@ -718,16 +790,15 @@ CONFIG_DEVPORT=y CONFIG_I2C=y CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y +CONFIG_I2C_ALGOBIT=y # -# I2C Algorithms +# I2C Hardware Bus support # -# CONFIG_I2C_ALGOBIT is not set -# CONFIG_I2C_ALGOPCF is not set -# CONFIG_I2C_ALGOPCA is not set # -# I2C Hardware Bus support +# PC SMBus host controller drivers # # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set @@ -735,52 +806,64 @@ CONFIG_I2C_CHARDEV=y # CONFIG_I2C_AMD756 is not set # CONFIG_I2C_AMD8111 is not set # CONFIG_I2C_I801 is not set -# CONFIG_I2C_I810 is not set +# CONFIG_I2C_ISCH is not set # CONFIG_I2C_PIIX4 is not set -CONFIG_I2C_MPC=y # CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_PROSAVAGE is not set -# CONFIG_I2C_SAVAGE4 is not set -# CONFIG_I2C_SIMTEC is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_TAOS_EVM is not set -# CONFIG_I2C_STUB is not set -# CONFIG_I2C_TINY_USB is not set # CONFIG_I2C_VIA is not set # CONFIG_I2C_VIAPRO is not set + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_MPC=y +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Graphics adapter I2C/DDC channel drivers +# # CONFIG_I2C_VOODOO3 is not set # +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# # Miscellaneous I2C Chip support # -# CONFIG_SENSORS_DS1337 is not set -# CONFIG_SENSORS_DS1374 is not set # CONFIG_DS1682 is not set +# CONFIG_AT24 is not set # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_M41T00 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set - -# -# SPI support -# # CONFIG_SPI is not set -# CONFIG_SPI_MASTER is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +# CONFIG_GPIOLIB is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_AD7414 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -788,7 +871,9 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7462 is not set # CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set # CONFIG_SENSORS_I5K_AMB is not set @@ -818,6 +903,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_SMSC47M1 is not set # CONFIG_SENSORS_SMSC47M192 is not set # CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set # CONFIG_SENSORS_THMC50 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_VT1211 is not set @@ -827,9 +913,12 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83792D is not set # CONFIG_SENSORS_W83793 is not set # CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set @@ -837,6 +926,7 @@ CONFIG_WATCHDOG=y # Watchdog Device Drivers # # CONFIG_SOFT_WATCHDOG is not set +# CONFIG_ALIM7101_WDT is not set # CONFIG_MPC5200_WDT is not set # CONFIG_WATCHDOG_RTAS is not set @@ -850,23 +940,39 @@ CONFIG_WATCHDOG=y # USB-based Watchdog Cards # # CONFIG_USBPCWATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_REGULATOR is not set # # Multimedia devices # + +# +# Multimedia core support +# # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# CONFIG_DAB=y # CONFIG_USB_DABUSB is not set @@ -874,11 +980,78 @@ CONFIG_DAB=y # Graphics support # # CONFIG_AGP is not set -# CONFIG_DRM is not set +CONFIG_DRM=y +# CONFIG_DRM_TDFX is not set +# CONFIG_DRM_R128 is not set +# CONFIG_DRM_RADEON is not set +# CONFIG_DRM_MGA is not set +# CONFIG_DRM_VIA is not set +# CONFIG_DRM_SAVAGE is not set # CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +CONFIG_FB_DDC=y +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +CONFIG_FB_MACMODES=y +CONFIG_FB_BACKLIGHT=y +CONFIG_FB_MODE_HELPERS=y +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_CIRRUS is not set +# CONFIG_FB_PM2 is not set +# CONFIG_FB_CYBER2000 is not set +# CONFIG_FB_OF is not set +# CONFIG_FB_CT65550 is not set +# CONFIG_FB_ASILIANT is not set +# CONFIG_FB_IMSTT is not set +# CONFIG_FB_VGA16 is not set +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_NVIDIA is not set +# CONFIG_FB_RIVA is not set +# CONFIG_FB_MATROX is not set +CONFIG_FB_RADEON=y +CONFIG_FB_RADEON_I2C=y +CONFIG_FB_RADEON_BACKLIGHT=y +# CONFIG_FB_RADEON_DEBUG is not set +# CONFIG_FB_ATY128 is not set +# CONFIG_FB_ATY is not set +# CONFIG_FB_S3 is not set +# CONFIG_FB_SAVAGE is not set +# CONFIG_FB_SIS is not set +# CONFIG_FB_VIA is not set +# CONFIG_FB_NEOMAGIC is not set +# CONFIG_FB_KYRO is not set +# CONFIG_FB_3DFX is not set +# CONFIG_FB_VOODOO1 is not set +# CONFIG_FB_VT8623 is not set +# CONFIG_FB_TRIDENT is not set +# CONFIG_FB_ARK is not set +# CONFIG_FB_PM3 is not set +# CONFIG_FB_CARMINE is not set +# CONFIG_FB_IBM_GXT4500 is not set +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=m +# CONFIG_LCD_ILI9320 is not set +# CONFIG_LCD_PLATFORM is not set +CONFIG_BACKLIGHT_CLASS_DEVICE=y +# CONFIG_BACKLIGHT_CORGI is not set # # Display device support @@ -886,15 +1059,64 @@ CONFIG_VIDEO_OUTPUT_CONTROL=m # CONFIG_DISPLAY_SUPPORT is not set # -# Sound -# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set +# CONFIG_FONTS is not set +CONFIG_FONT_8x8=y +CONFIG_FONT_8x16=y +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_MONO=y +CONFIG_LOGO_LINUX_VGA16=y +CONFIG_LOGO_LINUX_CLUT224=y # CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=y +# CONFIG_HID_PID is not set +# CONFIG_USB_HIDDEV is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y +CONFIG_HID_A4TECH=y +# CONFIG_HID_APPLE is not set +CONFIG_HID_BELKIN=y +CONFIG_HID_BRIGHT=y +CONFIG_HID_CHERRY=y +# CONFIG_HID_CHICONY is not set +CONFIG_HID_CYPRESS=y +CONFIG_HID_DELL=y +CONFIG_HID_EZKEY=y +# CONFIG_HID_GYRATION is not set +# CONFIG_HID_LOGITECH is not set +# CONFIG_HID_MICROSOFT is not set +# CONFIG_HID_MONTEREY is not set +# CONFIG_HID_PANTHERLORD is not set +# CONFIG_HID_PETALYNX is not set +# CONFIG_HID_SAMSUNG is not set +# CONFIG_HID_SONY is not set +# CONFIG_HID_SUNPLUS is not set +# CONFIG_THRUSTMASTER_FF is not set +# CONFIG_ZEROPLUS_FF is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set # # Miscellaneous USB options @@ -903,14 +1125,20 @@ CONFIG_USB_DEVICEFS=y # CONFIG_USB_DEVICE_CLASS is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_SUSPEND is not set -# CONFIG_USB_PERSIST is not set # CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +CONFIG_USB_MON=y +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set # # USB Host Controller Drivers # +# CONFIG_USB_C67X00_HCD is not set # CONFIG_USB_EHCI_HCD is not set # CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set CONFIG_USB_OHCI_HCD=y CONFIG_USB_OHCI_HCD_PPC_SOC=y CONFIG_USB_OHCI_HCD_PPC_OF=y @@ -923,12 +1151,17 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y # CONFIG_USB_UHCI_HCD is not set # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_WHCI_HCD is not set +# CONFIG_USB_HWA_HCD is not set +# CONFIG_USB_MUSB_HDRC is not set # # USB Device Class drivers # # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' @@ -948,7 +1181,9 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set # CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set # CONFIG_USB_LIBUSUAL is not set # @@ -956,15 +1191,10 @@ CONFIG_USB_STORAGE=y # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set -CONFIG_USB_MON=y # # USB port drivers # - -# -# USB Serial Converter support -# # CONFIG_USB_SERIAL is not set # @@ -973,7 +1203,7 @@ CONFIG_USB_MON=y # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set -# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_SEVSEG is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set @@ -989,18 +1219,14 @@ CONFIG_USB_MON=y # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set - -# -# USB DSL modem support -# - -# -# USB Gadget Support -# +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set # CONFIG_USB_GADGET is not set +# CONFIG_UWB is not set # CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set CONFIG_NEW_LEDS=y -CONFIG_LEDS_CLASS=y +# CONFIG_LEDS_CLASS is not set # # LED drivers @@ -1009,17 +1235,15 @@ CONFIG_LEDS_CLASS=y # # LED Triggers # -CONFIG_LEDS_TRIGGERS=y -CONFIG_LEDS_TRIGGER_TIMER=y -# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set +# CONFIG_LEDS_TRIGGERS is not set +# CONFIG_ACCESSIBILITY is not set # CONFIG_INFINIBAND is not set # CONFIG_EDAC is not set # CONFIG_RTC_CLASS is not set - -# -# Userspace I/O -# +# CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -1031,21 +1255,19 @@ CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set -# CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_ROMFS_FS is not set +CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set -CONFIG_DNOTIFY=y # CONFIG_AUTOFS_FS is not set # CONFIG_AUTOFS4_FS is not set # CONFIG_FUSE_FS is not set @@ -1072,6 +1294,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -1101,8 +1324,11 @@ CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set CONFIG_CRAMFS=y # CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set CONFIG_NETWORK_FILESYSTEMS=y @@ -1110,15 +1336,14 @@ CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y -# CONFIG_NFS_DIRECTIO is not set -# CONFIG_NFSD is not set CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y -# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -1173,7 +1398,6 @@ CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set # CONFIG_DLM is not set -# CONFIG_UCC_SLOW is not set # # Library routines @@ -1181,6 +1405,7 @@ CONFIG_NLS_ISO8859_1=y CONFIG_BITREVERSE=y # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y # CONFIG_CRC7 is not set @@ -1191,7 +1416,7 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y -# CONFIG_INSTRUMENTATION is not set +CONFIG_HAVE_LMB=y # # Kernel hacking @@ -1199,6 +1424,7 @@ CONFIG_HAS_DMA=y CONFIG_PRINTK_TIME=y CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set @@ -1206,10 +1432,14 @@ CONFIG_ENABLE_MUST_CHECK=y CONFIG_DEBUG_KERNEL=y # CONFIG_DEBUG_SHIRQ is not set CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 CONFIG_SCHED_DEBUG=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set # CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_SLUB_STATS is not set # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set # CONFIG_DEBUG_SPINLOCK is not set @@ -1220,17 +1450,39 @@ CONFIG_SCHED_DEBUG=y # CONFIG_DEBUG_BUGVERBOSE is not set CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set # CONFIG_DEBUG_LIST is not set # CONFIG_DEBUG_SG is not set -CONFIG_FORCED_INLINING=y # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_HAVE_FUNCTION_TRACER=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set -# CONFIG_DEBUGGER is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_MSI_BITMAP_SELFTEST is not set +# CONFIG_XMON is not set +# CONFIG_IRQSTACKS is not set # CONFIG_BDI_SWITCH is not set # CONFIG_BOOTX_TEXT is not set # CONFIG_PPC_EARLY_DEBUG is not set @@ -1240,47 +1492,98 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# # CONFIG_CRYPTO_HMAC is not set # CONFIG_CRYPTO_XCBC is not set -# CONFIG_CRYPTO_NULL is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set # CONFIG_CRYPTO_SHA1 is not set # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set -# CONFIG_CRYPTO_WP512 is not set # CONFIG_CRYPTO_TGR192 is not set -# CONFIG_CRYPTO_GF128MUL is not set -# CONFIG_CRYPTO_ECB is not set -CONFIG_CRYPTO_CBC=y -# CONFIG_CRYPTO_PCBC is not set -# CONFIG_CRYPTO_LRW is not set -# CONFIG_CRYPTO_XTS is not set -# CONFIG_CRYPTO_CRYPTD is not set -CONFIG_CRYPTO_DES=y -# CONFIG_CRYPTO_FCRYPT is not set -# CONFIG_CRYPTO_BLOWFISH is not set -# CONFIG_CRYPTO_TWOFISH is not set -# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# # CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_CAST5 is not set # CONFIG_CRYPTO_CAST6 is not set -# CONFIG_CRYPTO_TEA is not set -# CONFIG_CRYPTO_ARC4 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set # CONFIG_CRYPTO_KHAZAD is not set -# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SALSA20 is not set # CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# # CONFIG_CRYPTO_DEFLATE is not set -# CONFIG_CRYPTO_MICHAEL_MIC is not set -# CONFIG_CRYPTO_CRC32C is not set -# CONFIG_CRYPTO_CAMELLIA is not set -# CONFIG_CRYPTO_TEST is not set -# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y +# CONFIG_CRYPTO_DEV_HIFN_795X is not set CONFIG_PPC_CLOCK=y CONFIG_PPC_LIB_RHEAP=y +# CONFIG_VIRTUALIZATION is not set -- cgit v1.1 From c8d698849e135780738c2cb08f07f06eda982a8c Mon Sep 17 00:00:00 2001 From: Grant Likely Date: Fri, 14 Nov 2008 11:10:55 -0700 Subject: powerpc/virtex: Update defconfigs Update defconfigs for running on Xilinx Virtex platforms Signed-off-by: Grant Likely --- arch/powerpc/configs/40x/virtex_defconfig | 1176 ++++++++++++++++++++++++++++ arch/powerpc/configs/44x/virtex5_defconfig | 234 +++--- arch/powerpc/configs/ppc40x_defconfig | 92 ++- arch/powerpc/configs/ppc44x_defconfig | 92 ++- 4 files changed, 1469 insertions(+), 125 deletions(-) create mode 100644 arch/powerpc/configs/40x/virtex_defconfig (limited to 'arch') diff --git a/arch/powerpc/configs/40x/virtex_defconfig b/arch/powerpc/configs/40x/virtex_defconfig new file mode 100644 index 0000000..9a9350d --- /dev/null +++ b/arch/powerpc/configs/40x/virtex_defconfig @@ -0,0 +1,1176 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.28-rc4 +# Fri Nov 14 10:49:16 2008 +# +# CONFIG_PPC64 is not set + +# +# Processor support +# +# CONFIG_6xx is not set +# CONFIG_PPC_85xx is not set +# CONFIG_PPC_8xx is not set +CONFIG_40x=y +# CONFIG_44x is not set +# CONFIG_E200 is not set +CONFIG_4xx=y +# CONFIG_PPC_MM_SLICES is not set +CONFIG_NOT_COHERENT_CACHE=y +CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 +# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set +CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set +CONFIG_IRQ_PER_CPU=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_RWSEM_XCHGADD_ALGORITHM=y +CONFIG_ARCH_HAS_ILOG2_U32=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_GPIO=y +# CONFIG_ARCH_NO_VIRT_TO_BUS is not set +CONFIG_PPC=y +CONFIG_EARLY_PRINTK=y +CONFIG_GENERIC_NVRAM=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_PPC_OF=y +CONFIG_OF=y +CONFIG_PPC_UDBG_16550=y +# CONFIG_GENERIC_TBSYNC is not set +CONFIG_AUDIT_ARCH=y +CONFIG_GENERIC_BUG=y +# CONFIG_DEFAULT_UIMAGE is not set +CONFIG_PPC_DCR_NATIVE=y +# CONFIG_PPC_DCR_MMIO is not set +CONFIG_PPC_DCR=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_LOCK_KERNEL=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +# CONFIG_LOCALVERSION_AUTO is not set +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_POSIX_MQUEUE=y +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +CONFIG_NAMESPACES=y +# CONFIG_UTS_NS is not set +# CONFIG_IPC_NS is not set +# CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +# CONFIG_EMBEDDED is not set +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_AIO=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_PCI_QUIRKS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y +CONFIG_HAVE_IOREMAP_PROT=y +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MODVERSIONS=y +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +# CONFIG_DEFAULT_AS is not set +# CONFIG_DEFAULT_DEADLINE is not set +CONFIG_DEFAULT_CFQ=y +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set +# CONFIG_PPC4xx_PCI_EXPRESS is not set + +# +# Platform support +# +# CONFIG_PPC_CELL is not set +# CONFIG_PPC_CELL_NATIVE is not set +# CONFIG_PQ2ADS is not set +# CONFIG_PPC4xx_GPIO is not set +CONFIG_XILINX_VIRTEX=y +# CONFIG_ACADIA is not set +# CONFIG_EP405 is not set +# CONFIG_HCU4 is not set +# CONFIG_KILAUEA is not set +# CONFIG_MAKALU is not set +# CONFIG_WALNUT is not set +CONFIG_XILINX_VIRTEX_GENERIC_BOARD=y +# CONFIG_PPC40x_SIMPLE is not set +CONFIG_XILINX_VIRTEX_II_PRO=y +CONFIG_XILINX_VIRTEX_4_FX=y +CONFIG_IBM405_ERR77=y +CONFIG_IBM405_ERR51=y +# CONFIG_IPIC is not set +# CONFIG_MPIC is not set +# CONFIG_MPIC_WEIRD is not set +# CONFIG_PPC_I8259 is not set +# CONFIG_PPC_RTAS is not set +# CONFIG_MMIO_NVRAM is not set +# CONFIG_PPC_MPC106 is not set +# CONFIG_PPC_970_NAP is not set +# CONFIG_PPC_INDIRECT_IO is not set +# CONFIG_GENERIC_IOMAP is not set +# CONFIG_CPU_FREQ is not set +# CONFIG_FSL_ULI1575 is not set + +# +# Kernel options +# +# CONFIG_HIGHMEM is not set +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 +# CONFIG_SCHED_HRTICK is not set +# CONFIG_PREEMPT_NONE is not set +# CONFIG_PREEMPT_VOLUNTARY is not set +CONFIG_PREEMPT=y +# CONFIG_PREEMPT_RCU is not set +CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set +# CONFIG_BINFMT_MISC is not set +CONFIG_MATH_EMULATION=y +# CONFIG_IOMMU_HELPER is not set +CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +CONFIG_ARCH_HAS_WALK_MEMORY=y +CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y +CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +CONFIG_MIGRATION=y +CONFIG_RESOURCES_64BIT=y +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y +CONFIG_FORCE_MAX_ZONEORDER=11 +CONFIG_PROC_DEVICETREE=y +CONFIG_CMDLINE_BOOL=y +CONFIG_CMDLINE="" +CONFIG_EXTRA_TARGETS="" +# CONFIG_PM is not set +CONFIG_SECCOMP=y +CONFIG_ISA_DMA_API=y + +# +# Bus options +# +CONFIG_ZONE_DMA=y +CONFIG_PPC_INDIRECT_PCI=y +CONFIG_4xx_SOC=y +CONFIG_PPC_PCI_CHOICE=y +CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_SYSCALL=y +# CONFIG_PCIEPORTBUS is not set +CONFIG_ARCH_SUPPORTS_MSI=y +# CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y +# CONFIG_PCI_DEBUG is not set +# CONFIG_PCCARD is not set +# CONFIG_HOTPLUG_PCI is not set +# CONFIG_HAS_RAPIDIO is not set + +# +# Advanced setup +# +# CONFIG_ADVANCED_OPTIONS is not set + +# +# Default settings for advanced configuration options are used +# +CONFIG_LOWMEM_SIZE=0x30000000 +CONFIG_PAGE_OFFSET=0xc0000000 +CONFIG_KERNEL_START=0xc0000000 +CONFIG_PHYSICAL_START=0x00000000 +CONFIG_TASK_SIZE=0xc0000000 +CONFIG_CONSISTENT_START=0xff100000 +CONFIG_CONSISTENT_SIZE=0x00200000 +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +CONFIG_INET_TUNNEL=m +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +CONFIG_IPV6=m +# CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +# CONFIG_INET6_AH is not set +# CONFIG_INET6_ESP is not set +# CONFIG_INET6_IPCOMP is not set +# CONFIG_IPV6_MIP6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +CONFIG_INET6_XFRM_MODE_TRANSPORT=m +CONFIG_INET6_XFRM_MODE_TUNNEL=m +CONFIG_INET6_XFRM_MODE_BEET=m +# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set +CONFIG_IPV6_SIT=m +CONFIG_IPV6_NDISC_NODETYPE=y +# CONFIG_IPV6_TUNNEL is not set +# CONFIG_IPV6_MULTIPLE_TABLES is not set +# CONFIG_IPV6_MROUTE is not set +# CONFIG_NETWORK_SECMARK is not set +CONFIG_NETFILTER=y +# CONFIG_NETFILTER_DEBUG is not set +CONFIG_NETFILTER_ADVANCED=y + +# +# Core Netfilter Configuration +# +# CONFIG_NETFILTER_NETLINK_QUEUE is not set +# CONFIG_NETFILTER_NETLINK_LOG is not set +# CONFIG_NF_CONNTRACK is not set +CONFIG_NETFILTER_XTABLES=m +# CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set +# CONFIG_NETFILTER_XT_TARGET_DSCP is not set +# CONFIG_NETFILTER_XT_TARGET_MARK is not set +# CONFIG_NETFILTER_XT_TARGET_NFLOG is not set +# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set +# CONFIG_NETFILTER_XT_TARGET_RATEEST is not set +# CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set +# CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set +# CONFIG_NETFILTER_XT_MATCH_COMMENT is not set +# CONFIG_NETFILTER_XT_MATCH_DCCP is not set +# CONFIG_NETFILTER_XT_MATCH_DSCP is not set +# CONFIG_NETFILTER_XT_MATCH_ESP is not set +# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set +# CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set +# CONFIG_NETFILTER_XT_MATCH_LENGTH is not set +# CONFIG_NETFILTER_XT_MATCH_LIMIT is not set +# CONFIG_NETFILTER_XT_MATCH_MAC is not set +# CONFIG_NETFILTER_XT_MATCH_MARK is not set +# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set +# CONFIG_NETFILTER_XT_MATCH_OWNER is not set +# CONFIG_NETFILTER_XT_MATCH_POLICY is not set +# CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set +# CONFIG_NETFILTER_XT_MATCH_QUOTA is not set +# CONFIG_NETFILTER_XT_MATCH_RATEEST is not set +# CONFIG_NETFILTER_XT_MATCH_REALM is not set +# CONFIG_NETFILTER_XT_MATCH_RECENT is not set +# CONFIG_NETFILTER_XT_MATCH_SCTP is not set +# CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set +# CONFIG_NETFILTER_XT_MATCH_STRING is not set +# CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set +# CONFIG_NETFILTER_XT_MATCH_TIME is not set +# CONFIG_NETFILTER_XT_MATCH_U32 is not set +# CONFIG_IP_VS is not set + +# +# IP: Netfilter Configuration +# +# CONFIG_NF_DEFRAG_IPV4 is not set +# CONFIG_IP_NF_QUEUE is not set +CONFIG_IP_NF_IPTABLES=m +# CONFIG_IP_NF_MATCH_ADDRTYPE is not set +# CONFIG_IP_NF_MATCH_AH is not set +# CONFIG_IP_NF_MATCH_ECN is not set +# CONFIG_IP_NF_MATCH_TTL is not set +CONFIG_IP_NF_FILTER=m +# CONFIG_IP_NF_TARGET_REJECT is not set +# CONFIG_IP_NF_TARGET_LOG is not set +# CONFIG_IP_NF_TARGET_ULOG is not set +CONFIG_IP_NF_MANGLE=m +# CONFIG_IP_NF_TARGET_ECN is not set +# CONFIG_IP_NF_TARGET_TTL is not set +# CONFIG_IP_NF_RAW is not set +# CONFIG_IP_NF_ARPTABLES is not set + +# +# IPv6: Netfilter Configuration +# +# CONFIG_IP6_NF_QUEUE is not set +# CONFIG_IP6_NF_IPTABLES is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +# CONFIG_PHONET is not set +CONFIG_WIRELESS=y +# CONFIG_CFG80211 is not set +CONFIG_WIRELESS_OLD_REGULATORY=y +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +# CONFIG_MTD is not set +CONFIG_OF_DEVICE=y +CONFIG_OF_GPIO=y +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_XILINX_SYSACE=y +# CONFIG_BLK_DEV_HD is not set +CONFIG_MISC_DEVICES=y +# CONFIG_PHANTOM is not set +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_SGI_IOC4 is not set +# CONFIG_TIFM_CORE is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_HP_ILO is not set +# CONFIG_C2PORT is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# + +# +# Enable only one of the two stacks, unless you know what you are doing +# +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set +# CONFIG_I2O is not set +# CONFIG_MACINTOSH_DRIVERS is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_CASSINI is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_NET_TULIP is not set +# CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set +# CONFIG_NET_PCI is not set +# CONFIG_B44 is not set +# CONFIG_ATL2 is not set +CONFIG_NETDEV_1000=y +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_E1000E is not set +# CONFIG_IP1000 is not set +# CONFIG_IGB is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SIS190 is not set +# CONFIG_SKGE is not set +# CONFIG_SKY2 is not set +# CONFIG_VIA_VELOCITY is not set +# CONFIG_TIGON3 is not set +# CONFIG_BNX2 is not set +# CONFIG_QLA3XXX is not set +# CONFIG_ATL1 is not set +# CONFIG_ATL1E is not set +# CONFIG_JME is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +CONFIG_KEYBOARD_ATKBD=y +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +# CONFIG_KEYBOARD_GPIO is not set +CONFIG_INPUT_MOUSE=y +CONFIG_MOUSE_PS2=y +CONFIG_MOUSE_PS2_ALPS=y +CONFIG_MOUSE_PS2_LOGIPS2PP=y +CONFIG_MOUSE_PS2_SYNAPTICS=y +CONFIG_MOUSE_PS2_LIFEBOOK=y +CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set +# CONFIG_MOUSE_PS2_TOUCHKIT is not set +# CONFIG_MOUSE_SERIAL is not set +# CONFIG_MOUSE_VSXXXAA is not set +# CONFIG_MOUSE_GPIO is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_SERPORT is not set +# CONFIG_SERIO_PCIPS2 is not set +CONFIG_SERIO_LIBPS2=y +# CONFIG_SERIO_RAW is not set +CONFIG_SERIO_XILINX_XPS_PS2=y +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_PCI=y +CONFIG_SERIAL_8250_NR_UARTS=4 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_UARTLITE=y +CONFIG_SERIAL_UARTLITE_CONSOLE=y +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_JSM is not set +# CONFIG_SERIAL_OF_PLATFORM is not set +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=m +# CONFIG_NVRAM is not set +# CONFIG_GEN_RTC is not set +CONFIG_XILINX_HWICAP=y +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +# CONFIG_I2C is not set +# CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y + +# +# Memory mapped GPIO expanders: +# +CONFIG_GPIO_XILINX=y + +# +# I2C GPIO expanders: +# + +# +# PCI GPIO expanders: +# +# CONFIG_GPIO_BT8XX is not set + +# +# SPI GPIO expanders: +# +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +# CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y + +# +# Sonics Silicon Backplane +# +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_CIRRUS is not set +# CONFIG_FB_PM2 is not set +# CONFIG_FB_CYBER2000 is not set +# CONFIG_FB_OF is not set +# CONFIG_FB_CT65550 is not set +# CONFIG_FB_ASILIANT is not set +# CONFIG_FB_IMSTT is not set +# CONFIG_FB_VGA16 is not set +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_NVIDIA is not set +# CONFIG_FB_RIVA is not set +# CONFIG_FB_MATROX is not set +# CONFIG_FB_RADEON is not set +# CONFIG_FB_ATY128 is not set +# CONFIG_FB_ATY is not set +# CONFIG_FB_S3 is not set +# CONFIG_FB_SAVAGE is not set +# CONFIG_FB_SIS is not set +# CONFIG_FB_VIA is not set +# CONFIG_FB_NEOMAGIC is not set +# CONFIG_FB_KYRO is not set +# CONFIG_FB_3DFX is not set +# CONFIG_FB_VOODOO1 is not set +# CONFIG_FB_VT8623 is not set +# CONFIG_FB_TRIDENT is not set +# CONFIG_FB_ARK is not set +# CONFIG_FB_PM3 is not set +# CONFIG_FB_CARMINE is not set +# CONFIG_FB_IBM_GXT4500 is not set +CONFIG_FB_XILINX=y +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +CONFIG_DUMMY_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set +CONFIG_FONTS=y +CONFIG_FONT_8x8=y +CONFIG_FONT_8x16=y +# CONFIG_FONT_6x11 is not set +# CONFIG_FONT_7x14 is not set +# CONFIG_FONT_PEARL_8x8 is not set +# CONFIG_FONT_ACORN_8x8 is not set +# CONFIG_FONT_MINI_4x6 is not set +# CONFIG_FONT_SUN8x16 is not set +# CONFIG_FONT_SUN12x22 is not set +# CONFIG_FONT_10x18 is not set +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_MONO=y +CONFIG_LOGO_LINUX_VGA16=y +CONFIG_LOGO_LINUX_CLUT224=y +# CONFIG_SOUND is not set +# CONFIG_HID_SUPPORT is not set +# CONFIG_USB_SUPPORT is not set +# CONFIG_UWB is not set +# CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set +# CONFIG_NEW_LEDS is not set +# CONFIG_ACCESSIBILITY is not set +# CONFIG_INFINIBAND is not set +# CONFIG_EDAC is not set +# CONFIG_RTC_CLASS is not set +# CONFIG_DMADEVICES is not set +# CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +CONFIG_AUTOFS_FS=y +CONFIG_AUTOFS4_FS=y +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +# CONFIG_PROC_KCORE is not set +CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_CRAMFS=y +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +CONFIG_ROMFS_FS=y +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_SUNRPC_REGISTER_V4 is not set +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +CONFIG_NLS_ASCII=m +CONFIG_NLS_ISO8859_1=m +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +CONFIG_CRC_CCITT=y +# CONFIG_CRC16 is not set +# CONFIG_CRC_T10DIF is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_HAVE_LMB=y + +# +# Kernel hacking +# +CONFIG_PRINTK_TIME=y +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +# CONFIG_MAGIC_SYSRQ is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_HAVE_FUNCTION_TRACER=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_PREEMPT_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_MSI_BITMAP_SELFTEST is not set +# CONFIG_XMON is not set +# CONFIG_IRQSTACKS is not set +# CONFIG_BDI_SWITCH is not set +# CONFIG_PPC_EARLY_DEBUG is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +# CONFIG_CRYPTO_FIPS is not set +# CONFIG_CRYPTO_MANAGER is not set +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +# CONFIG_CRYPTO_CBC is not set +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +# CONFIG_CRYPTO_ECB is not set +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_HW=y +# CONFIG_CRYPTO_DEV_HIFN_795X is not set +# CONFIG_PPC_CLOCK is not set +# CONFIG_VIRTUALIZATION is not set diff --git a/arch/powerpc/configs/44x/virtex5_defconfig b/arch/powerpc/configs/44x/virtex5_defconfig index 663ec51..7513d36 100644 --- a/arch/powerpc/configs/44x/virtex5_defconfig +++ b/arch/powerpc/configs/44x/virtex5_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc1 -# Tue Aug 5 09:20:16 2008 +# Linux kernel version: 2.6.28-rc4 +# Fri Nov 14 10:31:16 2008 # # CONFIG_PPC64 is not set @@ -22,14 +22,13 @@ CONFIG_PHYS_64BIT=y CONFIG_NOT_COHERENT_CACHE=y CONFIG_PPC32=y CONFIG_WORD_SIZE=32 -CONFIG_PPC_MERGE=y +CONFIG_ARCH_PHYS_ADDR_T_64BIT=y CONFIG_MMU=y CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_GENERIC_TIME=y CONFIG_GENERIC_TIME_VSYSCALL=y CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y -# CONFIG_HAVE_GET_USER_PAGES_FAST is not set # CONFIG_HAVE_SETUP_PER_CPU_AREA is not set CONFIG_IRQ_PER_CPU=y CONFIG_STACKTRACE_SUPPORT=y @@ -40,6 +39,7 @@ CONFIG_ARCH_HAS_ILOG2_U32=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_NO_VIRT_TO_BUS is not set CONFIG_PPC=y CONFIG_EARLY_PRINTK=y @@ -93,8 +93,8 @@ CONFIG_INITRAMFS_SOURCE="" CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_SYSCTL_SYSCALL=y -CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_HOTPLUG=y CONFIG_PRINTK=y @@ -109,7 +109,9 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y +CONFIG_PCI_QUIRKS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set @@ -122,10 +124,6 @@ CONFIG_HAVE_IOREMAP_PROT=y CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y CONFIG_HAVE_ARCH_TRACEHOOK=y -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -158,6 +156,7 @@ CONFIG_DEFAULT_CFQ=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="cfq" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # CONFIG_PPC4xx_PCI_EXPRESS is not set # @@ -174,9 +173,13 @@ CONFIG_CLASSIC_RCU=y # CONFIG_KATMAI is not set # CONFIG_RAINIER is not set # CONFIG_WARP is not set +# CONFIG_ARCHES is not set # CONFIG_CANYONLANDS is not set +# CONFIG_GLACIER is not set # CONFIG_YOSEMITE is not set CONFIG_XILINX_VIRTEX440_GENERIC_BOARD=y +# CONFIG_PPC44x_SIMPLE is not set +# CONFIG_PPC4xx_GPIO is not set CONFIG_XILINX_VIRTEX=y CONFIG_XILINX_VIRTEX_5_FXT=y # CONFIG_IPIC is not set @@ -196,7 +199,6 @@ CONFIG_XILINX_VIRTEX_5_FXT=y # Kernel options # # CONFIG_HIGHMEM is not set -# CONFIG_TICK_ONESHOT is not set # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set CONFIG_GENERIC_CLOCKEVENTS_BUILD=y @@ -211,6 +213,8 @@ CONFIG_HZ=250 CONFIG_PREEMPT=y # CONFIG_PREEMPT_RCU is not set CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set CONFIG_MATH_EMULATION=y # CONFIG_IOMMU_HELPER is not set @@ -225,15 +229,15 @@ CONFIG_FLATMEM_MANUAL=y # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_MIGRATION=y CONFIG_RESOURCES_64BIT=y +CONFIG_PHYS_ADDR_T_64BIT=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y CONFIG_FORCE_MAX_ZONEORDER=11 CONFIG_PROC_DEVICETREE=y CONFIG_CMDLINE_BOOL=y @@ -256,6 +260,7 @@ CONFIG_PCI_SYSCALL=y CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set CONFIG_PCI_LEGACY=y +# CONFIG_PCI_DEBUG is not set # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set # CONFIG_HAS_RAPIDIO is not set @@ -317,7 +322,6 @@ CONFIG_INET_TCP_DIAG=y CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m # CONFIG_IPV6_PRIVACY is not set # CONFIG_IPV6_ROUTER_PREF is not set @@ -352,8 +356,8 @@ CONFIG_NETFILTER_XTABLES=m # CONFIG_NETFILTER_XT_TARGET_CLASSIFY is not set # CONFIG_NETFILTER_XT_TARGET_DSCP is not set # CONFIG_NETFILTER_XT_TARGET_MARK is not set -# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set # CONFIG_NETFILTER_XT_TARGET_NFLOG is not set +# CONFIG_NETFILTER_XT_TARGET_NFQUEUE is not set # CONFIG_NETFILTER_XT_TARGET_RATEEST is not set # CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set # CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP is not set @@ -361,36 +365,38 @@ CONFIG_NETFILTER_XTABLES=m # CONFIG_NETFILTER_XT_MATCH_DCCP is not set # CONFIG_NETFILTER_XT_MATCH_DSCP is not set # CONFIG_NETFILTER_XT_MATCH_ESP is not set +# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set # CONFIG_NETFILTER_XT_MATCH_IPRANGE is not set # CONFIG_NETFILTER_XT_MATCH_LENGTH is not set # CONFIG_NETFILTER_XT_MATCH_LIMIT is not set # CONFIG_NETFILTER_XT_MATCH_MAC is not set # CONFIG_NETFILTER_XT_MATCH_MARK is not set +# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set # CONFIG_NETFILTER_XT_MATCH_OWNER is not set # CONFIG_NETFILTER_XT_MATCH_POLICY is not set -# CONFIG_NETFILTER_XT_MATCH_MULTIPORT is not set # CONFIG_NETFILTER_XT_MATCH_PKTTYPE is not set # CONFIG_NETFILTER_XT_MATCH_QUOTA is not set # CONFIG_NETFILTER_XT_MATCH_RATEEST is not set # CONFIG_NETFILTER_XT_MATCH_REALM is not set +# CONFIG_NETFILTER_XT_MATCH_RECENT is not set # CONFIG_NETFILTER_XT_MATCH_SCTP is not set # CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set # CONFIG_NETFILTER_XT_MATCH_STRING is not set # CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set # CONFIG_NETFILTER_XT_MATCH_TIME is not set # CONFIG_NETFILTER_XT_MATCH_U32 is not set -# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +# CONFIG_NF_DEFRAG_IPV4 is not set # CONFIG_IP_NF_QUEUE is not set CONFIG_IP_NF_IPTABLES=m -# CONFIG_IP_NF_MATCH_RECENT is not set -# CONFIG_IP_NF_MATCH_ECN is not set +# CONFIG_IP_NF_MATCH_ADDRTYPE is not set # CONFIG_IP_NF_MATCH_AH is not set +# CONFIG_IP_NF_MATCH_ECN is not set # CONFIG_IP_NF_MATCH_TTL is not set -# CONFIG_IP_NF_MATCH_ADDRTYPE is not set CONFIG_IP_NF_FILTER=m # CONFIG_IP_NF_TARGET_REJECT is not set # CONFIG_IP_NF_TARGET_LOG is not set @@ -411,6 +417,7 @@ CONFIG_IP_NF_MANGLE=m # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -431,11 +438,10 @@ CONFIG_IP_NF_MANGLE=m # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# +# CONFIG_PHONET is not set +CONFIG_WIRELESS=y # CONFIG_CFG80211 is not set +CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_MAC80211 is not set # CONFIG_IEEE80211 is not set @@ -455,11 +461,13 @@ CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y CONFIG_FIRMWARE_IN_KERNEL=y CONFIG_EXTRA_FIRMWARE="" +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set # CONFIG_SYS_HYPERVISOR is not set # CONFIG_CONNECTOR is not set # CONFIG_MTD is not set CONFIG_OF_DEVICE=y -CONFIG_OF_I2C=y +CONFIG_OF_GPIO=y # CONFIG_PARPORT is not set CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_FD is not set @@ -478,7 +486,7 @@ CONFIG_BLK_DEV_RAM_SIZE=8192 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set -# CONFIG_XILINX_SYSACE is not set +CONFIG_XILINX_SYSACE=y # CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y # CONFIG_PHANTOM is not set @@ -487,6 +495,7 @@ CONFIG_MISC_DEVICES=y # CONFIG_TIFM_CORE is not set # CONFIG_ENCLOSURE_SERVICES is not set # CONFIG_HP_ILO is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -534,8 +543,12 @@ CONFIG_MII=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set @@ -556,6 +569,7 @@ CONFIG_NETDEV_1000=y # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set +# CONFIG_JME is not set # CONFIG_NETDEV_10000 is not set # CONFIG_TR is not set @@ -604,6 +618,7 @@ CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set # CONFIG_KEYBOARD_STOWAWAY is not set +# CONFIG_KEYBOARD_GPIO is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y CONFIG_MOUSE_PS2_ALPS=y @@ -611,9 +626,11 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set # CONFIG_MOUSE_SERIAL is not set # CONFIG_MOUSE_VSXXXAA is not set +# CONFIG_MOUSE_GPIO is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set # CONFIG_INPUT_TOUCHSCREEN is not set @@ -624,11 +641,11 @@ CONFIG_MOUSE_PS2_TRACKPOINT=y # CONFIG_SERIO=y # CONFIG_SERIO_I8042 is not set -CONFIG_SERIO_SERPORT=y +# CONFIG_SERIO_SERPORT is not set # CONFIG_SERIO_PCIPS2 is not set CONFIG_SERIO_LIBPS2=y # CONFIG_SERIO_RAW is not set -# CONFIG_SERIO_XILINX_XPS_PS2 is not set +CONFIG_SERIO_XILINX_XPS_PS2=y # CONFIG_GAMEPORT is not set # @@ -656,11 +673,12 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # # Non-8250 serial port support # -# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_UARTLITE=y +CONFIG_SERIAL_UARTLITE_CONSOLE=y CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y # CONFIG_SERIAL_JSM is not set -CONFIG_SERIAL_OF_PLATFORM=y +# CONFIG_SERIAL_OF_PLATFORM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 @@ -674,87 +692,41 @@ CONFIG_XILINX_HWICAP=y # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y - -# -# I2C Hardware Bus support -# - -# -# PC SMBus host controller drivers -# -# CONFIG_I2C_ALI1535 is not set -# CONFIG_I2C_ALI1563 is not set -# CONFIG_I2C_ALI15X3 is not set -# CONFIG_I2C_AMD756 is not set -# CONFIG_I2C_AMD8111 is not set -# CONFIG_I2C_I801 is not set -# CONFIG_I2C_ISCH is not set -# CONFIG_I2C_PIIX4 is not set -# CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_SIS5595 is not set -# CONFIG_I2C_SIS630 is not set -# CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_VIA is not set -# CONFIG_I2C_VIAPRO is not set +# CONFIG_I2C is not set +# CONFIG_SPI is not set +CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y # -# I2C system bus drivers (mostly embedded / system-on-chip) +# Memory mapped GPIO expanders: # -# CONFIG_I2C_IBM_IIC is not set -# CONFIG_I2C_MPC is not set -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_SIMTEC is not set +CONFIG_GPIO_XILINX=y # -# External I2C/SMBus adapter drivers +# I2C GPIO expanders: # -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_TAOS_EVM is not set # -# Graphics adapter I2C/DDC channel drivers +# PCI GPIO expanders: # -# CONFIG_I2C_VOODOO3 is not set +# CONFIG_GPIO_BT8XX is not set # -# Other I2C/SMBus bus drivers +# SPI GPIO expanders: # -# CONFIG_I2C_PCA_PLATFORM is not set -# CONFIG_I2C_STUB is not set - -# -# Miscellaneous I2C Chip support -# -# CONFIG_DS1682 is not set -# CONFIG_AT24 is not set -# CONFIG_SENSORS_EEPROM is not set -# CONFIG_SENSORS_PCF8574 is not set -# CONFIG_PCF8575 is not set -# CONFIG_SENSORS_PCA9539 is not set -# CONFIG_SENSORS_PCF8591 is not set -# CONFIG_SENSORS_MAX6875 is not set -# CONFIG_SENSORS_TSL2550 is not set -CONFIG_I2C_DEBUG_CORE=y -CONFIG_I2C_DEBUG_ALGO=y -# CONFIG_I2C_DEBUG_BUS is not set -# CONFIG_I2C_DEBUG_CHIP is not set -# CONFIG_SPI is not set -CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y -# CONFIG_GPIOLIB is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -763,6 +735,8 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -790,6 +764,7 @@ CONFIG_SSB_POSSIBLE=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y @@ -826,6 +801,7 @@ CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_S3 is not set # CONFIG_FB_SAVAGE is not set # CONFIG_FB_SIS is not set +# CONFIG_FB_VIA is not set # CONFIG_FB_NEOMAGIC is not set # CONFIG_FB_KYRO is not set # CONFIG_FB_3DFX is not set @@ -838,6 +814,8 @@ CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_IBM_GXT4500 is not set CONFIG_FB_XILINX=y # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -870,6 +848,7 @@ CONFIG_LOGO_LINUX_CLUT224=y # CONFIG_SOUND is not set # CONFIG_HID_SUPPORT is not set # CONFIG_USB_SUPPORT is not set +# CONFIG_UWB is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set @@ -879,6 +858,8 @@ CONFIG_LOGO_LINUX_CLUT224=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -887,10 +868,11 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XATTR is not set # CONFIG_EXT2_FS_XIP is not set # CONFIG_EXT3_FS is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set CONFIG_DNOTIFY=y @@ -899,7 +881,7 @@ CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set CONFIG_AUTOFS_FS=y CONFIG_AUTOFS4_FS=y -CONFIG_FUSE_FS=m +# CONFIG_FUSE_FS is not set # # CD-ROM/DVD Filesystems @@ -923,6 +905,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y # CONFIG_PROC_KCORE is not set CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -954,19 +937,15 @@ CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set CONFIG_ROOT_NFS=y -CONFIG_NFSD=y -CONFIG_NFSD_V3=y -# CONFIG_NFSD_V3_ACL is not set -# CONFIG_NFSD_V4 is not set +# CONFIG_NFSD is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y -CONFIG_EXPORTFS=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y +# CONFIG_SUNRPC_REGISTER_V4 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set -CONFIG_SMB_FS=y -# CONFIG_SMB_NLS_DEFAULT is not set +# CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set @@ -1023,7 +1002,6 @@ CONFIG_NLS_UTF8=m # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set CONFIG_CRC_CCITT=y # CONFIG_CRC16 is not set # CONFIG_CRC_T10DIF is not set @@ -1041,7 +1019,7 @@ CONFIG_HAVE_LMB=y # # Kernel hacking # -# CONFIG_PRINTK_TIME is not set +CONFIG_PRINTK_TIME=y CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_FRAME_WARN=1024 @@ -1049,19 +1027,62 @@ CONFIG_FRAME_WARN=1024 # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set -# CONFIG_DEBUG_KERNEL is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_MUTEXES is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_FAULT_INJECTION is not set # CONFIG_LATENCYTOP is not set -CONFIG_HAVE_FTRACE=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -# CONFIG_FTRACE is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_HAVE_FUNCTION_TRACER=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set # CONFIG_PREEMPT_TRACER is not set # CONFIG_SCHED_TRACER is not set # CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +# CONFIG_DEBUG_STACKOVERFLOW is not set +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_PAGEALLOC is not set +# CONFIG_CODE_PATCHING_SELFTEST is not set +# CONFIG_FTR_FIXUP_SELFTEST is not set +# CONFIG_MSI_BITMAP_SELFTEST is not set +# CONFIG_XMON is not set # CONFIG_IRQSTACKS is not set +# CONFIG_BDI_SWITCH is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -1069,12 +1090,14 @@ CONFIG_HAVE_ARCH_KGDB=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set # CONFIG_CRYPTO_MANAGER is not set # CONFIG_CRYPTO_GF128MUL is not set # CONFIG_CRYPTO_NULL is not set @@ -1147,6 +1170,11 @@ CONFIG_CRYPTO=y # # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y # CONFIG_CRYPTO_DEV_HIFN_795X is not set # CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/ppc40x_defconfig b/arch/powerpc/configs/ppc40x_defconfig index c15c91d..4256e2c 100644 --- a/arch/powerpc/configs/ppc40x_defconfig +++ b/arch/powerpc/configs/ppc40x_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.28-rc2 -# Tue Oct 28 08:56:44 2008 +# Linux kernel version: 2.6.28-rc4 +# Fri Nov 14 09:54:44 2008 # # CONFIG_PPC64 is not set @@ -500,15 +500,17 @@ CONFIG_BLK_DEV_RAM_SIZE=35000 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set -# CONFIG_XILINX_SYSACE is not set +CONFIG_XILINX_SYSACE=m # CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y # CONFIG_PHANTOM is not set # CONFIG_EEPROM_93CX6 is not set # CONFIG_SGI_IOC4 is not set # CONFIG_TIFM_CORE is not set +# CONFIG_ICS932S401 is not set # CONFIG_ENCLOSURE_SERVICES is not set # CONFIG_HP_ILO is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -632,7 +634,13 @@ CONFIG_NETDEV_10000=y # # Hardware I/O ports # -# CONFIG_SERIO is not set +CONFIG_SERIO=m +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_SERPORT is not set +# CONFIG_SERIO_PCIPS2 is not set +# CONFIG_SERIO_LIBPS2 is not set +# CONFIG_SERIO_RAW is not set +CONFIG_SERIO_XILINX_XPS_PS2=m # CONFIG_GAMEPORT is not set # @@ -660,7 +668,8 @@ CONFIG_SERIAL_8250_SHARE_IRQ=y # # Non-8250 serial port support # -# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_UARTLITE=y +CONFIG_SERIAL_UARTLITE_CONSOLE=y CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y # CONFIG_SERIAL_JSM is not set @@ -757,6 +766,11 @@ CONFIG_GPIOLIB=y # CONFIG_GPIO_SYSFS is not set # +# Memory mapped GPIO expanders: +# +CONFIG_GPIO_XILINX=y + +# # I2C GPIO expanders: # # CONFIG_GPIO_MAX732X is not set @@ -776,11 +790,11 @@ CONFIG_GPIOLIB=y # CONFIG_HWMON is not set CONFIG_THERMAL=y # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -792,6 +806,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_TMIO is not set # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -816,13 +831,65 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_DRM is not set # CONFIG_VGASTATE is not set CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set +CONFIG_FB=m +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +CONFIG_FB_CFB_FILLRECT=m +CONFIG_FB_CFB_COPYAREA=m +CONFIG_FB_CFB_IMAGEBLIT=m +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_CIRRUS is not set +# CONFIG_FB_PM2 is not set +# CONFIG_FB_CYBER2000 is not set +# CONFIG_FB_VGA16 is not set +# CONFIG_FB_UVESA is not set +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_NVIDIA is not set +# CONFIG_FB_RIVA is not set +# CONFIG_FB_MATROX is not set +# CONFIG_FB_RADEON is not set +# CONFIG_FB_ATY128 is not set +# CONFIG_FB_ATY is not set +# CONFIG_FB_S3 is not set +# CONFIG_FB_SAVAGE is not set +# CONFIG_FB_SIS is not set +# CONFIG_FB_VIA is not set +# CONFIG_FB_NEOMAGIC is not set +# CONFIG_FB_KYRO is not set +# CONFIG_FB_3DFX is not set +# CONFIG_FB_VOODOO1 is not set +# CONFIG_FB_VT8623 is not set +# CONFIG_FB_TRIDENT is not set +# CONFIG_FB_ARK is not set +# CONFIG_FB_PM3 is not set +# CONFIG_FB_CARMINE is not set +# CONFIG_FB_IBM_GXT4500 is not set +CONFIG_FB_XILINX=m +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set +# CONFIG_LOGO is not set # CONFIG_SOUND is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y @@ -851,6 +918,7 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set # CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -1077,10 +1145,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_FAULT_INJECTION is not set # CONFIG_LATENCYTOP is not set CONFIG_SYSCTL_SYSCALL_CHECK=y -CONFIG_NOP_TRACER=y -CONFIG_HAVE_FTRACE=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -# CONFIG_FTRACE is not set +CONFIG_HAVE_FUNCTION_TRACER=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set # CONFIG_SCHED_TRACER is not set # CONFIG_CONTEXT_SWITCH_TRACER is not set # CONFIG_BOOT_TRACER is not set diff --git a/arch/powerpc/configs/ppc44x_defconfig b/arch/powerpc/configs/ppc44x_defconfig index 55edbd5..cfc94cf 100644 --- a/arch/powerpc/configs/ppc44x_defconfig +++ b/arch/powerpc/configs/ppc44x_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.28-rc2 -# Tue Oct 28 09:28:58 2008 +# Linux kernel version: 2.6.28-rc4 +# Fri Nov 14 10:06:19 2008 # # CONFIG_PPC64 is not set @@ -506,15 +506,17 @@ CONFIG_BLK_DEV_RAM_SIZE=35000 # CONFIG_BLK_DEV_XIP is not set # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set -# CONFIG_XILINX_SYSACE is not set +CONFIG_XILINX_SYSACE=m # CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y # CONFIG_PHANTOM is not set # CONFIG_EEPROM_93CX6 is not set # CONFIG_SGI_IOC4 is not set # CONFIG_TIFM_CORE is not set +# CONFIG_ICS932S401 is not set # CONFIG_ENCLOSURE_SERVICES is not set # CONFIG_HP_ILO is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -680,7 +682,13 @@ CONFIG_NETDEV_10000=y # # Hardware I/O ports # -# CONFIG_SERIO is not set +CONFIG_SERIO=m +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_SERPORT is not set +# CONFIG_SERIO_PCIPS2 is not set +# CONFIG_SERIO_LIBPS2 is not set +# CONFIG_SERIO_RAW is not set +CONFIG_SERIO_XILINX_XPS_PS2=m # CONFIG_GAMEPORT is not set # @@ -708,7 +716,8 @@ CONFIG_SERIAL_8250_SHARE_IRQ=y # # Non-8250 serial port support # -# CONFIG_SERIAL_UARTLITE is not set +CONFIG_SERIAL_UARTLITE=y +CONFIG_SERIAL_UARTLITE_CONSOLE=y CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y # CONFIG_SERIAL_JSM is not set @@ -806,6 +815,11 @@ CONFIG_GPIOLIB=y # CONFIG_GPIO_SYSFS is not set # +# Memory mapped GPIO expanders: +# +CONFIG_GPIO_XILINX=y + +# # I2C GPIO expanders: # # CONFIG_GPIO_MAX732X is not set @@ -826,11 +840,11 @@ CONFIG_GPIOLIB=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -842,6 +856,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_TMIO is not set # CONFIG_MFD_WM8400 is not set # CONFIG_MFD_WM8350_I2C is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -866,13 +881,65 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_DRM is not set # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set +CONFIG_FB=m +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +CONFIG_FB_CFB_FILLRECT=m +CONFIG_FB_CFB_COPYAREA=m +CONFIG_FB_CFB_IMAGEBLIT=m +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_CIRRUS is not set +# CONFIG_FB_PM2 is not set +# CONFIG_FB_CYBER2000 is not set +# CONFIG_FB_VGA16 is not set +# CONFIG_FB_UVESA is not set +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_NVIDIA is not set +# CONFIG_FB_RIVA is not set +# CONFIG_FB_MATROX is not set +# CONFIG_FB_RADEON is not set +# CONFIG_FB_ATY128 is not set +# CONFIG_FB_ATY is not set +# CONFIG_FB_S3 is not set +# CONFIG_FB_SAVAGE is not set +# CONFIG_FB_SIS is not set +# CONFIG_FB_VIA is not set +# CONFIG_FB_NEOMAGIC is not set +# CONFIG_FB_KYRO is not set +# CONFIG_FB_3DFX is not set +# CONFIG_FB_VOODOO1 is not set +# CONFIG_FB_VT8623 is not set +# CONFIG_FB_TRIDENT is not set +# CONFIG_FB_ARK is not set +# CONFIG_FB_PM3 is not set +# CONFIG_FB_CARMINE is not set +# CONFIG_FB_IBM_GXT4500 is not set +CONFIG_FB_XILINX=m +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set +# CONFIG_LOGO is not set # CONFIG_SOUND is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y @@ -1002,6 +1069,7 @@ CONFIG_USB_STORAGE=m # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set # CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -1227,10 +1295,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_FAULT_INJECTION is not set # CONFIG_LATENCYTOP is not set CONFIG_SYSCTL_SYSCALL_CHECK=y -CONFIG_NOP_TRACER=y -CONFIG_HAVE_FTRACE=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -# CONFIG_FTRACE is not set +CONFIG_HAVE_FUNCTION_TRACER=y + +# +# Tracers +# +# CONFIG_FUNCTION_TRACER is not set # CONFIG_SCHED_TRACER is not set # CONFIG_CONTEXT_SWITCH_TRACER is not set # CONFIG_BOOT_TRACER is not set -- cgit v1.1 From a4a16beadea041ab601e65b264b568e8b6b4f68d Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Mon, 10 Nov 2008 09:05:37 +0100 Subject: oprofile: fix an overflow in ppro code reset_value was changed from long to u64 in commit b99170288421c79f0c2efa8b33e26e65f4bb7fb8 (oprofile: Implement Intel architectural perfmon support) But dynamic allocation of this array use a wrong type (long instead of u64) Cc: Andi Kleen Signed-off-by: Eric Dumazet Signed-off-by: Robert Richter --- arch/x86/oprofile/op_model_ppro.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/oprofile/op_model_ppro.c b/arch/x86/oprofile/op_model_ppro.c index 3f1b81a..716d26f 100644 --- a/arch/x86/oprofile/op_model_ppro.c +++ b/arch/x86/oprofile/op_model_ppro.c @@ -69,7 +69,7 @@ static void ppro_setup_ctrs(struct op_msrs const * const msrs) int i; if (!reset_value) { - reset_value = kmalloc(sizeof(unsigned) * num_counters, + reset_value = kmalloc(sizeof(reset_value[0]) * num_counters, GFP_ATOMIC); if (!reset_value) return; -- cgit v1.1 From f464ff581c247d82fcc0e7ef40c1ca6df9739068 Mon Sep 17 00:00:00 2001 From: Trent Piepho Date: Wed, 19 Nov 2008 10:40:55 -0800 Subject: powerpc/85xx: L2 cache size wrong in 8572DS dts It's 1MB, not 512KB. Newer U-Boots will fix this entry, but that's no reason to have the wrong value in the dts. Signed-off-by: Trent Piepho Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8572ds.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mpc8572ds.dts b/arch/powerpc/boot/dts/mpc8572ds.dts index cadd465..5c69b2f 100644 --- a/arch/powerpc/boot/dts/mpc8572ds.dts +++ b/arch/powerpc/boot/dts/mpc8572ds.dts @@ -90,7 +90,7 @@ compatible = "fsl,mpc8572-l2-cache-controller"; reg = <0x20000 0x1000>; cache-line-size = <32>; // 32 bytes - cache-size = <0x80000>; // L2, 512K + cache-size = <0x100000>; // L2, 1M interrupt-parent = <&mpic>; interrupts = <16 2>; }; -- cgit v1.1 From 06597aa90a75621639dcaaf5fc07bcb01f752d45 Mon Sep 17 00:00:00 2001 From: Martyn Welch Date: Tue, 18 Nov 2008 10:55:45 +0000 Subject: powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610 The Marvell PHY driver is currently being used for the 88E1111 on the SBC610. This driver is causing the link to run in 10/Half mode, the generic PHY driver is correctly configuring the PHY as 1000/Full. Edit default config to use generic PHY driver. Signed-off-by: Martyn Welch Signed-off-by: Kumar Gala --- arch/powerpc/configs/86xx/gef_sbc610_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/configs/86xx/gef_sbc610_defconfig b/arch/powerpc/configs/86xx/gef_sbc610_defconfig index 2da13e0..07ccaf8 100644 --- a/arch/powerpc/configs/86xx/gef_sbc610_defconfig +++ b/arch/powerpc/configs/86xx/gef_sbc610_defconfig @@ -838,7 +838,7 @@ CONFIG_PHYLIB=y # # MII PHY device drivers # -CONFIG_MARVELL_PHY=y +# CONFIG_MARVELL_PHY is not set # CONFIG_DAVICOM_PHY is not set # CONFIG_QSEMI_PHY is not set # CONFIG_LXT_PHY is not set -- cgit v1.1 From e871809cccc11aaa072afaf746f8fd946d2d9cac Mon Sep 17 00:00:00 2001 From: Michael Barkowski Date: Thu, 13 Nov 2008 10:18:28 -0500 Subject: powerpc/mpc832x_rdb: fix swapped ethernet ids ethernet0 (called FSL UEC0 in U-Boot) should be enet1 (UCC3/eth1), and ethernet1 should be enet0 (UCC2/eth0), to be consistent with U-Boot so that the interfaces do not swap addresses when control passes from U-Boot to the kernel. Signed-off-by: Michael Barkowski Acked-by: Kim Phillips Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc832x_rdb.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mpc832x_rdb.dts b/arch/powerpc/boot/dts/mpc832x_rdb.dts index 226ff06..dea3091 100644 --- a/arch/powerpc/boot/dts/mpc832x_rdb.dts +++ b/arch/powerpc/boot/dts/mpc832x_rdb.dts @@ -18,8 +18,8 @@ #size-cells = <1>; aliases { - ethernet0 = &enet0; - ethernet1 = &enet1; + ethernet0 = &enet1; + ethernet1 = &enet0; serial0 = &serial0; serial1 = &serial1; pci0 = &pci0; -- cgit v1.1 From 9bc646f163b136684390081262fab0fd8f5343ca Mon Sep 17 00:00:00 2001 From: Rakib Mullick Date: Thu, 20 Nov 2008 19:08:45 +0600 Subject: x86: fix __cpuinit/__init tangle in init_thread_xstate() Impact: fix incorrect __init annotation This patch removes the following section mismatch warning. A patch set was send previously (http://lkml.org/lkml/2008/11/10/407). But introduce some other problem, reported by Rufus (http://lkml.org/lkml/2008/11/11/46). Then Ingo Molnar suggest that, it's best to remove __init from xsave_cntxt_init(void). Which is the second patch in this series. Now, this one removes the following warning. WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x2237): Section mismatch in reference from the function cpu_init() to the function .init.text:init_thread_xstate() The function __cpuinit cpu_init() references a function __init init_thread_xstate(). If init_thread_xstate is only used by cpu_init then annotate init_thread_xstate with a matching annotation. Signed-off-by: Rakib Mullick Signed-off-by: Ingo Molnar --- arch/x86/kernel/i387.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/i387.c b/arch/x86/kernel/i387.c index 1f20608..b0f61f0 100644 --- a/arch/x86/kernel/i387.c +++ b/arch/x86/kernel/i387.c @@ -58,7 +58,7 @@ void __cpuinit mxcsr_feature_mask_init(void) stts(); } -void __init init_thread_xstate(void) +void __cpuinit init_thread_xstate(void) { if (!HAVE_HWFP) { xstate_size = sizeof(struct i387_soft_struct); -- cgit v1.1 From bfe085f62f98a49e1b864e4950389c7205174e4f Mon Sep 17 00:00:00 2001 From: Rakib Mullick Date: Thu, 20 Nov 2008 19:12:50 +0600 Subject: x86: fixing __cpuinit/__init tangle, xsave_cntxt_init() Annotate xsave_cntxt_init() as "can be called outside of __init". Signed-off-by: Rakib Mullick Signed-off-by: Ingo Molnar --- arch/x86/kernel/xsave.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/xsave.c b/arch/x86/kernel/xsave.c index b13acb7..15c3e69 100644 --- a/arch/x86/kernel/xsave.c +++ b/arch/x86/kernel/xsave.c @@ -310,7 +310,7 @@ static void __init setup_xstate_init(void) /* * Enable and initialize the xsave feature. */ -void __init xsave_cntxt_init(void) +void __ref xsave_cntxt_init(void) { unsigned int eax, ebx, ecx, edx; -- cgit v1.1 From 606572634c3faa5b32a8fc430266e6e9d78d2179 Mon Sep 17 00:00:00 2001 From: Jeremy Kerr Date: Tue, 11 Nov 2008 10:22:22 +1100 Subject: powerpc/spufs: Fix spinning in spufs_ps_fault on signal Currently, we can end up in an infinite loop if we get a signal while the kernel has faulted in spufs_ps_fault. Eg: alarm(1); write(fd, some_spu_psmap_register_address, 4); - the write's copy_from_user will fault on the ps mapping, and signal_pending will be non-zero. Because returning from the fault handler will never clear TIF_SIGPENDING, so we'll just keep faulting, resulting in an unkillable process using 100% of CPU. This change returns VM_FAULT_SIGBUS if there's a fatal signal pending, letting us escape the loop. Signed-off-by: Jeremy Kerr --- arch/powerpc/platforms/cell/spufs/file.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/platforms/cell/spufs/file.c b/arch/powerpc/platforms/cell/spufs/file.c index b73c369..1b26071 100644 --- a/arch/powerpc/platforms/cell/spufs/file.c +++ b/arch/powerpc/platforms/cell/spufs/file.c @@ -390,6 +390,9 @@ static int spufs_ps_fault(struct vm_area_struct *vma, if (offset >= ps_size) return VM_FAULT_SIGBUS; + if (fatal_signal_pending(current)) + return VM_FAULT_SIGBUS; + /* * Because we release the mmap_sem, the context may be destroyed while * we're in spu_wait. Grab an extra reference so it isn't destroyed -- cgit v1.1 From 999f6338780fa0577b6581941c697c868d1ec2d3 Mon Sep 17 00:00:00 2001 From: Robert Jarzmik Date: Mon, 17 Nov 2008 20:29:03 +0100 Subject: [ARM] pxa/MioA701: fix memory corruption. In the resume bootstrap, the early disable address is wrong. Fix it to RAM address 0xa020b000 instead of 0xa0200000, and make it consistent with RESUME_ENABLE_ADDR in mioa701.c. Signed-off-by: Robert Jarzmik Acked-by: Russell King Signed-off-by: Eric Miao --- arch/arm/mach-pxa/mioa701_bootresume.S | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/mach-pxa/mioa701_bootresume.S b/arch/arm/mach-pxa/mioa701_bootresume.S index a647693..324d25a 100644 --- a/arch/arm/mach-pxa/mioa701_bootresume.S +++ b/arch/arm/mach-pxa/mioa701_bootresume.S @@ -24,6 +24,7 @@ ENTRY(mioa701_jumpaddr) 1: mov r0, #0xa0000000 @ Don't suppose memory access works orr r0, r0, #0x00200000 @ even if it's supposed to + orr r0, r0, #0x0000b000 mov r1, #0 str r1, [r0] @ Early disable resume for next boot ldr r0, mioa701_jumpaddr @ (Murphy's Law) -- cgit v1.1 From 844c6f6a36984c5fe1bcc2d68a88f2ed212d1eef Mon Sep 17 00:00:00 2001 From: Robert Jarzmik Date: Mon, 17 Nov 2008 20:29:04 +0100 Subject: [ARM] pxa/MioA701: bluetooth resume fix The G3IPL expects the value at RAM address 0xa020b020 to be exactly 1 to setup the bluetooth GPIOs properly. The actual code got a value from gpio_get_value() which was not 1, but a "not equal to 0" integer. Signed-off-by: Robert Jarzmik Acked-by: Russell King Signed-off-by: Eric Miao --- arch/arm/mach-pxa/mioa701.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-pxa/mioa701.c b/arch/arm/mach-pxa/mioa701.c index 0842c53..782903f 100644 --- a/arch/arm/mach-pxa/mioa701.c +++ b/arch/arm/mach-pxa/mioa701.c @@ -565,7 +565,7 @@ static int mioa701_sys_suspend(struct sys_device *sysdev, pm_message_t state) u32 *mem_resume_unknown = phys_to_virt(RESUME_UNKNOWN_ADDR); /* Devices prepare suspend */ - is_bt_on = gpio_get_value(GPIO83_BT_ON); + is_bt_on = !!gpio_get_value(GPIO83_BT_ON); pxa2xx_mfp_set_lpm(GPIO83_BT_ON, is_bt_on ? MFP_LPM_DRIVE_HIGH : MFP_LPM_DRIVE_LOW); -- cgit v1.1 From a1967d64414dab500e86cbbddf8eae6ad2047903 Mon Sep 17 00:00:00 2001 From: Thomas Gleixner Date: Fri, 21 Nov 2008 11:16:48 -0800 Subject: x86: revert irq number limitation Impact: fix MSIx not enough irq numbers available regression The manual revert of the sparse_irq patches missed to bring the number of possible irqs back to the .27 status. This resulted in a regression when two multichannel network cards were placed in a system with only one IO_APIC - causing the networking driver to not have the right IRQ and the device not coming up. Remove the dynamic allocation logic leftovers and simply return NR_IRQS in probe_nr_irqs() for now. Fixes: http://lkml.org/lkml/2008/11/19/354 Reported-by: Jesper Dangaard Brouer Signed-off-by: Thomas Gleixner Tested-by: Jesper Dangaard Brouer Acked-by: Yinghai Lu Signed-off-by: Ingo Molnar --- arch/x86/kernel/io_apic.c | 22 +--------------------- 1 file changed, 1 insertion(+), 21 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/io_apic.c b/arch/x86/kernel/io_apic.c index c9513e1..1fec0f9 100644 --- a/arch/x86/kernel/io_apic.c +++ b/arch/x86/kernel/io_apic.c @@ -3608,27 +3608,7 @@ int __init io_apic_get_redir_entries (int ioapic) int __init probe_nr_irqs(void) { - int idx; - int nr = 0; -#ifndef CONFIG_XEN - int nr_min = 32; -#else - int nr_min = NR_IRQS; -#endif - - for (idx = 0; idx < nr_ioapics; idx++) - nr += io_apic_get_redir_entries(idx) + 1; - - /* double it for hotplug and msi and nmi */ - nr <<= 1; - - /* something wrong ? */ - if (nr < nr_min) - nr = nr_min; - if (WARN_ON(nr > NR_IRQS)) - nr = NR_IRQS; - - return nr; + return NR_IRQS; } /* -------------------------------------------------------------------------- -- cgit v1.1 From 86bbc2c235e500957b213e7e64ce2e0ccb8bc131 Mon Sep 17 00:00:00 2001 From: Ian Campbell Date: Fri, 21 Nov 2008 10:21:33 +0000 Subject: xen: pin correct PGD on suspend Impact: fix Xen guest boot failure commit eefb47f6a1e855653d275cb90592a3587ea93a09 ("xen: use spin_lock_nest_lock when pinning a pagetable") changed xen_pgd_walk to walk over mm->pgd rather than taking pgd as an argument. This breaks xen_mm_(un)pin_all() because it makes init_mm.pgd readonly instead of the pgd we are interested in and therefore the pin subsequently fails. (XEN) mm.c:2280:d15 Bad type (saw 00000000e8000001 != exp 0000000060000000) for mfn bc464 (pfn 21ca7) (XEN) mm.c:2665:d15 Error while pinning mfn bc464 [ 14.586913] 1 multicall(s) failed: cpu 0 [ 14.586926] Pid: 14, comm: kstop/0 Not tainted 2.6.28-rc5-x86_32p-xenU-00172-gee2f6cc #200 [ 14.586940] Call Trace: [ 14.586955] [] ? printk+0x18/0x1e [ 14.586972] [] xen_mc_flush+0x163/0x1d0 [ 14.586986] [] __xen_pgd_pin+0xa1/0x110 [ 14.587000] [] ? stop_cpu+0x0/0xf0 [ 14.587015] [] xen_mm_pin_all+0x4b/0x70 [ 14.587029] [] xen_suspend+0x39/0xe0 [ 14.587042] [] ? stop_cpu+0x0/0xf0 [ 14.587054] [] stop_cpu+0x9d/0xf0 [ 14.587067] [] run_workqueue+0x8d/0x150 [ 14.587080] [] ? _spin_unlock_irqrestore+0x23/0x40 [ 14.587094] [] ? prepare_to_wait+0x3a/0x70 [ 14.587107] [] worker_thread+0x88/0xf0 [ 14.587120] [] ? autoremove_wake_function+0x0/0x50 [ 14.587133] [] ? worker_thread+0x0/0xf0 [ 14.587146] [] kthread+0x3c/0x70 [ 14.587157] [] ? kthread+0x0/0x70 [ 14.587170] [] kernel_thread_helper+0x7/0x10 [ 14.587181] call 1/3: op=14 arg=[c0415000] result=0 [ 14.587192] call 2/3: op=14 arg=[e1ca2000] result=0 [ 14.587204] call 3/3: op=26 arg=[c1808860] result=-22 Signed-off-by: Ian Campbell Acked-by: Jeremy Fitzhardinge Signed-off-by: Ingo Molnar --- arch/x86/xen/mmu.c | 21 ++++++++++++++------- 1 file changed, 14 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/x86/xen/mmu.c b/arch/x86/xen/mmu.c index 6889360..636ef4c 100644 --- a/arch/x86/xen/mmu.c +++ b/arch/x86/xen/mmu.c @@ -661,12 +661,11 @@ void xen_set_pgd(pgd_t *ptr, pgd_t val) * For 64-bit, we must skip the Xen hole in the middle of the address * space, just after the big x86-64 virtual hole. */ -static int xen_pgd_walk(struct mm_struct *mm, - int (*func)(struct mm_struct *mm, struct page *, - enum pt_level), - unsigned long limit) +static int __xen_pgd_walk(struct mm_struct *mm, pgd_t *pgd, + int (*func)(struct mm_struct *mm, struct page *, + enum pt_level), + unsigned long limit) { - pgd_t *pgd = mm->pgd; int flush = 0; unsigned hole_low, hole_high; unsigned pgdidx_limit, pudidx_limit, pmdidx_limit; @@ -753,6 +752,14 @@ out: return flush; } +static int xen_pgd_walk(struct mm_struct *mm, + int (*func)(struct mm_struct *mm, struct page *, + enum pt_level), + unsigned long limit) +{ + return __xen_pgd_walk(mm, mm->pgd, func, limit); +} + /* If we're using split pte locks, then take the page's lock and return a pointer to it. Otherwise return NULL. */ static spinlock_t *xen_pte_lock(struct page *page, struct mm_struct *mm) @@ -854,7 +861,7 @@ static void __xen_pgd_pin(struct mm_struct *mm, pgd_t *pgd) xen_mc_batch(); - if (xen_pgd_walk(mm, xen_pin_page, USER_LIMIT)) { + if (__xen_pgd_walk(mm, pgd, xen_pin_page, USER_LIMIT)) { /* re-enable interrupts for flushing */ xen_mc_issue(0); @@ -998,7 +1005,7 @@ static void __xen_pgd_unpin(struct mm_struct *mm, pgd_t *pgd) PT_PMD); #endif - xen_pgd_walk(mm, xen_unpin_page, USER_LIMIT); + __xen_pgd_walk(mm, pgd, xen_unpin_page, USER_LIMIT); xen_mc_issue(0); } -- cgit v1.1 From 3eb77d5116d78cce5b9fa9eb19d012bc636116b6 Mon Sep 17 00:00:00 2001 From: Christian Borntraeger Date: Mon, 17 Nov 2008 14:50:35 +0100 Subject: KVM: s390: Fix problem state handling in guest sigp handler We can get an exit for instructions starting with 0xae, even if the guest is in userspace. Lets make sure, that the signal processor handler is only called in guest supervisor mode. Otherwise, send a program check. Signed-off-by: Christian Borntraeger Signed-off-by: Avi Kivity --- arch/s390/kvm/sigp.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch') diff --git a/arch/s390/kvm/sigp.c b/arch/s390/kvm/sigp.c index 1703926..2a01b9e 100644 --- a/arch/s390/kvm/sigp.c +++ b/arch/s390/kvm/sigp.c @@ -237,6 +237,11 @@ int kvm_s390_handle_sigp(struct kvm_vcpu *vcpu) u8 order_code; int rc; + /* sigp in userspace can exit */ + if (vcpu->arch.sie_block->gpsw.mask & PSW_MASK_PSTATE) + return kvm_s390_inject_program_int(vcpu, + PGM_PRIVILEGED_OPERATION); + order_code = disp2; if (base2) order_code += vcpu->arch.guest_gprs[base2]; -- cgit v1.1 From bd2b3ca7686d9470b1b58df631daa03179486182 Mon Sep 17 00:00:00 2001 From: Avi Kivity Date: Thu, 20 Nov 2008 11:47:18 +0200 Subject: KVM: VMX: Fix interrupt loss during race with NMI If an interrupt cannot be injected for some reason (say, page fault when fetching the IDT descriptor), the interrupt is marked for reinjection. However, if an NMI is queued at this time, the NMI will be injected instead and the NMI will be lost. Fix by deferring the NMI injection until the interrupt has been injected successfully. Analyzed by Jan Kiszka. Signed-off-by: Avi Kivity --- arch/x86/kvm/vmx.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kvm/vmx.c b/arch/x86/kvm/vmx.c index d06b4dc..a4018b0 100644 --- a/arch/x86/kvm/vmx.c +++ b/arch/x86/kvm/vmx.c @@ -3149,7 +3149,9 @@ static void vmx_intr_assist(struct kvm_vcpu *vcpu) if (cpu_has_virtual_nmis()) { if (vcpu->arch.nmi_pending && !vcpu->arch.nmi_injected) { - if (vmx_nmi_enabled(vcpu)) { + if (vcpu->arch.interrupt.pending) { + enable_nmi_window(vcpu); + } else if (vmx_nmi_enabled(vcpu)) { vcpu->arch.nmi_pending = false; vcpu->arch.nmi_injected = true; } else { -- cgit v1.1 From 547567c67774d872eb344d21e0f2d7a76eb1e9c5 Mon Sep 17 00:00:00 2001 From: Xiantao Zhang Date: Thu, 20 Nov 2008 10:35:35 +0800 Subject: KVM: ia64: Fix incorrect kbuild CFLAGS override Use CFLAGS_vcpu.o, not EXTRA_CFLAGS, to provide fixed register information to the compiler. Signed-off-by: Xiantao Zhang Signed-off-by: Avi Kivity --- arch/ia64/kvm/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/ia64/kvm/Makefile b/arch/ia64/kvm/Makefile index 3ab4d6d..92cef66 100644 --- a/arch/ia64/kvm/Makefile +++ b/arch/ia64/kvm/Makefile @@ -58,7 +58,7 @@ endif kvm-objs := $(common-objs) kvm-ia64.o kvm_fw.o obj-$(CONFIG_KVM) += kvm.o -EXTRA_CFLAGS_vcpu.o += -mfixed-range=f2-f5,f12-f127 +CFLAGS_vcpu.o += -mfixed-range=f2-f5,f12-f127 kvm-intel-objs = vmm.o vmm_ivt.o trampoline.o vcpu.o optvfault.o mmio.o \ vtlb.o process.o #Add link memcpy and memset to avoid possible structure assignment error -- cgit v1.1 From ce50b91d0f7b0b90e3960a6f306b4027378c7c27 Mon Sep 17 00:00:00 2001 From: Xiantao Zhang Date: Fri, 21 Nov 2008 10:56:08 +0800 Subject: KVM: ia64: Fix: Use correct calling convention for PAL_VPS_RESUME_HANDLER PAL_VPS_RESUME_HANDLER should use r26 to hold vac fields according to SDM. Signed-off-by: Xiantao Zhang Signed-off-by: Avi Kivity --- arch/ia64/kvm/optvfault.S | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/ia64/kvm/optvfault.S b/arch/ia64/kvm/optvfault.S index 634abad..32254ce 100644 --- a/arch/ia64/kvm/optvfault.S +++ b/arch/ia64/kvm/optvfault.S @@ -107,10 +107,10 @@ END(kvm_vps_resume_normal) GLOBAL_ENTRY(kvm_vps_resume_handler) movl r30 = PAL_VPS_RESUME_HANDLER ;; - ld8 r27=[r25] + ld8 r26=[r25] shr r17=r17,IA64_ISR_IR_BIT ;; - dep r27=r17,r27,63,1 // bit 63 of r27 indicate whether enable CFLE + dep r26=r17,r26,63,1 // bit 63 of r26 indicate whether enable CFLE mov pr=r23,-2 br.sptk.many kvm_vps_entry END(kvm_vps_resume_handler) @@ -894,12 +894,15 @@ ENTRY(kvm_resume_to_guest) ;; ld8 r19=[r19] mov b0=r29 - cmp.ne p6,p7 = r0,r0 + mov r27=cr.isr ;; - tbit.z p6,p7 = r19,IA64_PSR_IC_BIT // p1=vpsr.ic + tbit.z p6,p7 = r19,IA64_PSR_IC_BIT // p7=vpsr.ic + shr r27=r27,IA64_ISR_IR_BIT ;; (p6) ld8 r26=[r25] (p7) mov b0=r28 + ;; + (p6) dep r26=r27,r26,63,1 mov pr=r31,-2 br.sptk.many b0 // call pal service ;; -- cgit v1.1 From 0c0f40bdbe4ddb48ebecfb5c2b56eeb175a57c45 Mon Sep 17 00:00:00 2001 From: Marcelo Tosatti Date: Fri, 21 Nov 2008 19:13:58 +0100 Subject: KVM: MMU: fix sync of ptes addressed at owner pagetable During page sync, if a pagetable contains a self referencing pte (that points to the pagetable), the corresponding spte may be marked as writable even though all mappings are supposed to be write protected. Fix by clearing page unsync before syncing individual sptes. Signed-off-by: Marcelo Tosatti Signed-off-by: Avi Kivity --- arch/x86/kvm/mmu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kvm/mmu.c b/arch/x86/kvm/mmu.c index f1983d9..410ddbc 100644 --- a/arch/x86/kvm/mmu.c +++ b/arch/x86/kvm/mmu.c @@ -1038,13 +1038,13 @@ static int kvm_sync_page(struct kvm_vcpu *vcpu, struct kvm_mmu_page *sp) } rmap_write_protect(vcpu->kvm, sp->gfn); + kvm_unlink_unsync_page(vcpu->kvm, sp); if (vcpu->arch.mmu.sync_page(vcpu, sp)) { kvm_mmu_zap_page(vcpu->kvm, sp); return 1; } kvm_mmu_flush_tlb(vcpu); - kvm_unlink_unsync_page(vcpu->kvm, sp); return 0; } -- cgit v1.1 From 8ec2e24356e63dc298c6040557faf396410907ac Mon Sep 17 00:00:00 2001 From: David Daney Date: Thu, 20 Nov 2008 17:26:36 -0800 Subject: MIPS: Make BUG() __noreturn. Often we do things like put BUG() in the default clause of a case statement. Since it was not declared __noreturn, this could sometimes lead to bogus compiler warnings that variables were used uninitialized. There is a small problem in that we have to put a magic while(1); loop to fool GCC into really thinking it is noreturn. This makes the new BUG() function 3 instructions long instead of just 1, but I think it is worth it as it is now unnecessary to do extra work to silence the 'used uninitialized' warnings. I also re-wrote BUG_ON so that if it is given a constant condition, it just does BUG() instead of loading a constant value in to a register and testing it. Signed-off-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/include/asm/bug.h | 29 ++++++++++++++++++++--------- 1 file changed, 20 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/mips/include/asm/bug.h b/arch/mips/include/asm/bug.h index 7eb63de..08ea468 100644 --- a/arch/mips/include/asm/bug.h +++ b/arch/mips/include/asm/bug.h @@ -7,20 +7,31 @@ #include -#define BUG() \ -do { \ - __asm__ __volatile__("break %0" : : "i" (BRK_BUG)); \ -} while (0) +static inline void __noreturn BUG(void) +{ + __asm__ __volatile__("break %0" : : "i" (BRK_BUG)); + /* Fool GCC into thinking the function doesn't return. */ + while (1) + ; +} #define HAVE_ARCH_BUG #if (_MIPS_ISA > _MIPS_ISA_MIPS1) -#define BUG_ON(condition) \ -do { \ - __asm__ __volatile__("tne $0, %0, %1" \ - : : "r" (condition), "i" (BRK_BUG)); \ -} while (0) +static inline void __BUG_ON(unsigned long condition) +{ + if (__builtin_constant_p(condition)) { + if (condition) + BUG(); + else + return; + } + __asm__ __volatile__("tne $0, %0, %1" + : : "r" (condition), "i" (BRK_BUG)); +} + +#define BUG_ON(C) __BUG_ON((unsigned long)(C)) #define HAVE_ARCH_BUG_ON -- cgit v1.1 From c30f8a6c6d74f67bc2107726cc61a1e7c71e9740 Mon Sep 17 00:00:00 2001 From: Hollis Blanchard Date: Mon, 24 Nov 2008 11:37:38 -0600 Subject: KVM: ppc: stop leaking host memory on VM exit When the VM exits, we must call put_page() for every page referenced in the shadow TLB. Without this patch, we usually leak 30-50 host pages (120 - 200 KiB with 4 KiB pages). The maximum number of pages leaked is the size of our shadow TLB, 64 pages. Signed-off-by: Hollis Blanchard Signed-off-by: Avi Kivity --- arch/powerpc/include/asm/kvm_ppc.h | 2 ++ arch/powerpc/kvm/44x_tlb.c | 8 ++++++++ arch/powerpc/kvm/powerpc.c | 1 + 3 files changed, 11 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/include/asm/kvm_ppc.h b/arch/powerpc/include/asm/kvm_ppc.h index 8931ba7..bb62ad8 100644 --- a/arch/powerpc/include/asm/kvm_ppc.h +++ b/arch/powerpc/include/asm/kvm_ppc.h @@ -104,4 +104,6 @@ static inline void kvmppc_set_pid(struct kvm_vcpu *vcpu, u32 new_pid) } } +extern void kvmppc_core_destroy_mmu(struct kvm_vcpu *vcpu); + #endif /* __POWERPC_KVM_PPC_H__ */ diff --git a/arch/powerpc/kvm/44x_tlb.c b/arch/powerpc/kvm/44x_tlb.c index 2e227a4..ad72c6f 100644 --- a/arch/powerpc/kvm/44x_tlb.c +++ b/arch/powerpc/kvm/44x_tlb.c @@ -124,6 +124,14 @@ static void kvmppc_44x_shadow_release(struct kvm_vcpu *vcpu, } } +void kvmppc_core_destroy_mmu(struct kvm_vcpu *vcpu) +{ + int i; + + for (i = 0; i <= tlb_44x_hwater; i++) + kvmppc_44x_shadow_release(vcpu, i); +} + void kvmppc_tlbe_set_modified(struct kvm_vcpu *vcpu, unsigned int i) { vcpu->arch.shadow_tlb_mod[i] = 1; diff --git a/arch/powerpc/kvm/powerpc.c b/arch/powerpc/kvm/powerpc.c index 90a6fc4..fda9baa 100644 --- a/arch/powerpc/kvm/powerpc.c +++ b/arch/powerpc/kvm/powerpc.c @@ -238,6 +238,7 @@ int kvm_arch_vcpu_init(struct kvm_vcpu *vcpu) void kvm_arch_vcpu_uninit(struct kvm_vcpu *vcpu) { + kvmppc_core_destroy_mmu(vcpu); } /* Note: clearing MSR[DE] just means that the debug interrupt will not be -- cgit v1.1 From 5cf02b7bafddb6c3c16ddfb23d3ce187f70528ba Mon Sep 17 00:00:00 2001 From: Steven Rostedt Date: Tue, 25 Nov 2008 00:42:37 -0500 Subject: x86: use limited register constraint for setnz Impact: build fix with certain compilers GCC can decide to use %dil when "r" is used, which is not valid for setnz. This bug was brought out by Stephen Rothwell's merging of the branch tracer into linux-next. [ Thanks to Uros Bizjak for recommending 'q' over 'Q' ] Signed-off-by: Steven Rostedt Signed-off-by: Ingo Molnar --- arch/x86/boot/tty.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/boot/tty.c b/arch/x86/boot/tty.c index 0be77b3..7e8e8b2 100644 --- a/arch/x86/boot/tty.c +++ b/arch/x86/boot/tty.c @@ -74,7 +74,7 @@ static int kbd_pending(void) { u8 pending; asm volatile("int $0x16; setnz %0" - : "=rm" (pending) + : "=qm" (pending) : "a" (0x0100)); return pending; } -- cgit v1.1 From eff79aee91dd07e944df65fa448c8baeee7709d8 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Tue, 25 Nov 2008 14:13:03 +0100 Subject: arch/x86/kernel/pci-calgary_64.c: change simple_strtol to simple_strtoul Impact: fix theoretical option string parsing overflow Since bridge is unsigned, it would seem better to use simple_strtoul that simple_strtol. A simplified version of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @r2@ long e; position p; @@ e = simple_strtol@p(...) @@ position p != r2.p; type T; T e; @@ e = - simple_strtol@p + simple_strtoul (...) // Signed-off-by: Julia Lawall Cc: muli@il.ibm.com Cc: jdmason@kudzu.us Cc: discuss@x86-64.org Signed-off-by: Ingo Molnar --- arch/x86/kernel/pci-calgary_64.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/pci-calgary_64.c b/arch/x86/kernel/pci-calgary_64.c index e1e731d..d28bbdc 100644 --- a/arch/x86/kernel/pci-calgary_64.c +++ b/arch/x86/kernel/pci-calgary_64.c @@ -1567,7 +1567,7 @@ static int __init calgary_parse_options(char *p) ++p; if (*p == '\0') break; - bridge = simple_strtol(p, &endp, 0); + bridge = simple_strtoul(p, &endp, 0); if (p == endp) break; -- cgit v1.1 From 292c669cd7087a090d6420e223eb1072f3e3c50b Mon Sep 17 00:00:00 2001 From: Markus Metzger Date: Tue, 25 Nov 2008 08:45:13 +0100 Subject: x86, bts: exclude ds.c from build when disabled Impact: cleanup Move the CONFIG guard from the .c file into the makefile. Reported-by: Andi Kleen Signed-off-by: Markus Metzger Signed-off-by: Ingo Molnar --- arch/x86/kernel/Makefile | 2 +- arch/x86/kernel/ds.c | 3 --- 2 files changed, 1 insertion(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/Makefile b/arch/x86/kernel/Makefile index e489ff9..b62a766 100644 --- a/arch/x86/kernel/Makefile +++ b/arch/x86/kernel/Makefile @@ -41,7 +41,7 @@ obj-$(CONFIG_X86_TRAMPOLINE) += trampoline.o obj-y += process.o obj-y += i387.o xsave.o obj-y += ptrace.o -obj-y += ds.o +obj-$(CONFIG_X86_DS) += ds.o obj-$(CONFIG_X86_32) += tls.o obj-$(CONFIG_IA32_EMULATION) += tls.o obj-y += step.o diff --git a/arch/x86/kernel/ds.c b/arch/x86/kernel/ds.c index d1a1214..4c8d57e 100644 --- a/arch/x86/kernel/ds.c +++ b/arch/x86/kernel/ds.c @@ -21,8 +21,6 @@ */ -#ifdef CONFIG_X86_DS - #include #include @@ -878,4 +876,3 @@ void ds_free(struct ds_context *context) while (leftovers--) ds_put_context(context); } -#endif /* CONFIG_X86_DS */ -- cgit v1.1 From e5e8ca633bbe972eff6f84e064a63c0c08ed6c3d Mon Sep 17 00:00:00 2001 From: Markus Metzger Date: Tue, 25 Nov 2008 08:47:19 +0100 Subject: x86, bts: turn macro into static inline function Impact: cleanup Replace a macro with a static inline function. Signed-off-by: Markus Metzger Signed-off-by: Ingo Molnar --- arch/x86/include/asm/ds.h | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/x86/include/asm/ds.h b/arch/x86/include/asm/ds.h index 72c5a19..a950084 100644 --- a/arch/x86/include/asm/ds.h +++ b/arch/x86/include/asm/ds.h @@ -23,12 +23,13 @@ #ifndef _ASM_X86_DS_H #define _ASM_X86_DS_H -#ifdef CONFIG_X86_DS #include #include +#ifdef CONFIG_X86_DS + struct task_struct; /* @@ -232,7 +233,8 @@ extern void ds_free(struct ds_context *context); #else /* CONFIG_X86_DS */ -#define ds_init_intel(config) do {} while (0) +struct cpuinfo_x86; +static inline void __cpuinit ds_init_intel(struct cpuinfo_x86 *ignored) {} #endif /* CONFIG_X86_DS */ #endif /* _ASM_X86_DS_H */ -- cgit v1.1 From c4858ffc8f2dc850cb1f609c679b1ac1ad36ef0c Mon Sep 17 00:00:00 2001 From: Markus Metzger Date: Tue, 25 Nov 2008 08:49:06 +0100 Subject: x86, pebs: fix PEBS record size configuration Impact: fix DS hw enablement on 64-bit x86 Fix the PEBS record size in the DS configuration. Reported-by: Stephane Eranian Signed-off-by: Markus Metzger Signed-off-by: Ingo Molnar --- arch/x86/kernel/ds.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'arch') diff --git a/arch/x86/kernel/ds.c b/arch/x86/kernel/ds.c index 4c8d57e..04e38ef 100644 --- a/arch/x86/kernel/ds.c +++ b/arch/x86/kernel/ds.c @@ -816,13 +816,21 @@ static const struct ds_configuration ds_cfg_var = { .sizeof_ds = sizeof(long) * 12, .sizeof_field = sizeof(long), .sizeof_rec[ds_bts] = sizeof(long) * 3, +#ifdef __i386__ .sizeof_rec[ds_pebs] = sizeof(long) * 10 +#else + .sizeof_rec[ds_pebs] = sizeof(long) * 18 +#endif }; static const struct ds_configuration ds_cfg_64 = { .sizeof_ds = 8 * 12, .sizeof_field = 8, .sizeof_rec[ds_bts] = 8 * 3, +#ifdef __i386__ .sizeof_rec[ds_pebs] = 8 * 10 +#else + .sizeof_rec[ds_pebs] = 8 * 18 +#endif }; static inline void -- cgit v1.1 From de90add30e79261c3b5be68bb0f22d2ef98e8113 Mon Sep 17 00:00:00 2001 From: Markus Metzger Date: Tue, 25 Nov 2008 08:52:56 +0100 Subject: x86, bts: fix wrmsr and spinlock over kmalloc Impact: fix sleeping-with-spinlock-held bugs/crashes - Turn a wrmsr to write the DS_AREA MSR into a wrmsrl. - Use irqsave variants of spinlocks. - Do not allocate memory while holding spinlocks. Reported-by: Stephane Eranian Reported-by: Ingo Molnar Signed-off-by: Markus Metzger Signed-off-by: Ingo Molnar --- arch/x86/kernel/ds.c | 77 +++++++++++++++++++++++++++------------------------- 1 file changed, 40 insertions(+), 37 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/ds.c b/arch/x86/kernel/ds.c index 04e38ef..a2d1176 100644 --- a/arch/x86/kernel/ds.c +++ b/arch/x86/kernel/ds.c @@ -209,14 +209,15 @@ static DEFINE_PER_CPU(struct ds_context *, system_context); static inline struct ds_context *ds_get_context(struct task_struct *task) { struct ds_context *context; + unsigned long irq; - spin_lock(&ds_lock); + spin_lock_irqsave(&ds_lock, irq); context = (task ? task->thread.ds_ctx : this_system_context); if (context) context->count++; - spin_unlock(&ds_lock); + spin_unlock_irqrestore(&ds_lock, irq); return context; } @@ -224,55 +225,46 @@ static inline struct ds_context *ds_get_context(struct task_struct *task) /* * Same as ds_get_context, but allocates the context and it's DS * structure, if necessary; returns NULL; if out of memory. - * - * pre: requires ds_lock to be held */ static inline struct ds_context *ds_alloc_context(struct task_struct *task) { struct ds_context **p_context = (task ? &task->thread.ds_ctx : &this_system_context); struct ds_context *context = *p_context; + unsigned long irq; if (!context) { - spin_unlock(&ds_lock); - context = kzalloc(sizeof(*context), GFP_KERNEL); - - if (!context) { - spin_lock(&ds_lock); + if (!context) return NULL; - } context->ds = kzalloc(ds_cfg.sizeof_ds, GFP_KERNEL); if (!context->ds) { kfree(context); - spin_lock(&ds_lock); return NULL; } - spin_lock(&ds_lock); - /* - * Check for race - another CPU could have allocated - * it meanwhile: - */ + spin_lock_irqsave(&ds_lock, irq); + if (*p_context) { kfree(context->ds); kfree(context); - return *p_context; - } - - *p_context = context; - context->this = p_context; - context->task = task; + context = *p_context; + } else { + *p_context = context; - if (task) - set_tsk_thread_flag(task, TIF_DS_AREA_MSR); + context->this = p_context; + context->task = task; - if (!task || (task == current)) - wrmsr(MSR_IA32_DS_AREA, (unsigned long)context->ds, 0); + if (task) + set_tsk_thread_flag(task, TIF_DS_AREA_MSR); - get_tracer(task); + if (!task || (task == current)) + wrmsrl(MSR_IA32_DS_AREA, + (unsigned long)context->ds); + } + spin_unlock_irqrestore(&ds_lock, irq); } context->count++; @@ -286,10 +278,12 @@ static inline struct ds_context *ds_alloc_context(struct task_struct *task) */ static inline void ds_put_context(struct ds_context *context) { + unsigned long irq; + if (!context) return; - spin_lock(&ds_lock); + spin_lock_irqsave(&ds_lock, irq); if (--context->count) goto out; @@ -311,7 +305,7 @@ static inline void ds_put_context(struct ds_context *context) kfree(context->ds); kfree(context); out: - spin_unlock(&ds_lock); + spin_unlock_irqrestore(&ds_lock, irq); } @@ -382,6 +376,7 @@ static int ds_request(struct task_struct *task, void *base, size_t size, struct ds_context *context; unsigned long buffer, adj; const unsigned long alignment = (1 << 3); + unsigned long irq; int error = 0; if (!ds_cfg.sizeof_ds) @@ -396,26 +391,27 @@ static int ds_request(struct task_struct *task, void *base, size_t size, return -EOPNOTSUPP; - spin_lock(&ds_lock); - - error = -ENOMEM; context = ds_alloc_context(task); if (!context) - goto out_unlock; + return -ENOMEM; + + spin_lock_irqsave(&ds_lock, irq); error = -EPERM; if (!check_tracer(task)) goto out_unlock; + get_tracer(task); + error = -EALREADY; if (context->owner[qual] == current) - goto out_unlock; + goto out_put_tracer; error = -EPERM; if (context->owner[qual] != NULL) - goto out_unlock; + goto out_put_tracer; context->owner[qual] = current; - spin_unlock(&ds_lock); + spin_unlock_irqrestore(&ds_lock, irq); error = -ENOMEM; @@ -463,10 +459,17 @@ static int ds_request(struct task_struct *task, void *base, size_t size, out_release: context->owner[qual] = NULL; ds_put_context(context); + put_tracer(task); + return error; + + out_put_tracer: + spin_unlock_irqrestore(&ds_lock, irq); + ds_put_context(context); + put_tracer(task); return error; out_unlock: - spin_unlock(&ds_lock); + spin_unlock_irqrestore(&ds_lock, irq); ds_put_context(context); return error; } -- cgit v1.1 From a266d9f1253a38ec2d5655ebcd6846298b0554f4 Mon Sep 17 00:00:00 2001 From: Andreas Herrmann Date: Fri, 21 Nov 2008 14:49:25 +0100 Subject: [CPUFREQ] powernow-k8: ignore out-of-range PstateStatus value A workaround for AMD CPU family 11h erratum 311 might cause that the P-state Status Register shows a "current P-state" which is larger than the "current P-state limit" in P-state Current Limit Register. For the wrong P-state value there is no ACPI _PSS object defined and powernow-k8/cpufreq can't determine the proper CPU frequency for that state. As a consequence this can cause a panic during boot (potentially with all recent kernel versions -- at least I have reproduced it with various 2.6.27 kernels and with the current .28 series), as an example: powernow-k8: Found 1 AMD Turion(tm)X2 Ultra DualCore Mobile ZM-82 processors (2 \ ) powernow-k8: 0 : pstate 0 (2200 MHz) powernow-k8: 1 : pstate 1 (1100 MHz) powernow-k8: 2 : pstate 2 (600 MHz) BUG: unable to handle kernel paging request at ffff88086e7528b8 IP: [] cpufreq_stats_update+0x4a/0x5f PGD 202063 PUD 0 Oops: 0002 [#1] SMP last sysfs file: CPU 1 Modules linked in: Pid: 1, comm: swapper Not tainted 2.6.28-rc3-dirty #16 RIP: 0010:[] [] cpufreq_stats_update+0x4a/0\ f Synaptics claims to have extended capabilities, but I'm not able to read them.<6\ 6 RAX: 0000000000000000 RBX: 0000000000000001 RCX: ffff88006e7528c0 RDX: 00000000ffffffff RSI: ffff88006e54af00 RDI: ffffffff808f056c RBP: 00000000fffee697 R08: 0000000000000003 R09: ffff88006e73f080 R10: 0000000000000001 R11: 00000000002191c0 R12: ffff88006fb83c10 R13: 00000000ffffffff R14: 0000000000000001 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88006fb50740(0000) knlGS:0000000000000000 Unable to initialize Synaptics hardware. CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: ffff88086e7528b8 CR3: 0000000000201000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process swapper (pid: 1, threadinfo ffff88006fb82000, task ffff88006fb816d0) Stack: ffff88006e74da50 0000000000000000 ffff88006e54af00 ffffffff804863c7 ffff88006e74da50 0000000000000000 00000000ffffffff 0000000000000000 ffff88006fb83c10 ffffffff8024b46c ffffffff808f0560 ffff88006fb83c10 Call Trace: [] ? cpufreq_stat_notifier_trans+0x51/0x83 [] ? notifier_call_chain+0x29/0x4c [] ? __srcu_notifier_call_chain+0x46/0x61 [] ? cpufreq_notify_transition+0x93/0xa9 [] ? powernowk8_target+0x1e8/0x5f3 [] ? cpufreq_governor_performance+0x1b/0x20 [] ? __cpufreq_governor+0x71/0xa8 [] ? __cpufreq_set_policy+0x101/0x13e [] ? cpufreq_add_dev+0x3f0/0x4cd [] ? handle_update+0x0/0x8 [] ? sysdev_driver_register+0xb6/0x10d [] ? powernowk8_init+0x0/0x7e [] ? cpufreq_register_driver+0x8f/0x140 [] ? _stext+0x56/0x14f [] ? proc_register+0x122/0x17d [] ? create_proc_entry+0x73/0x8a [] ? register_irq_proc+0x92/0xaa [] ? init_irq_proc+0x57/0x69 [] ? kernel_init+0x116/0x169 [] ? child_rip+0xa/0x11 [] ? kernel_init+0x0/0x169 [] ? child_rip+0x0/0x11 Code: 05 c5 83 36 00 48 c7 c2 48 5d 86 80 48 8b 04 d8 48 8b 40 08 48 8b 34 02 48\ RIP [] cpufreq_stats_update+0x4a/0x5f RSP CR2: ffff88086e7528b8 ---[ end trace 0678bac75e67a2f7 ]--- Kernel panic - not syncing: Attempted to kill init! In short, aftereffect of the wrong P-state is that cpufreq_stats_update() uses "-1" as index for some array in cpufreq_stats_update (unsigned int cpu) { ... if (stat->time_in_state) stat->time_in_state[stat->last_index] = cputime64_add(stat->time_in_state[stat->last_index], cputime_sub(cur_time, stat->last_time)); ... } Fortunately, the wrong P-state value is returned only if the core is in P-state 0. This fix solves the problem by detecting the out-of-range P-state, ignoring it, and using "0" instead. Cc: Mark Langsdorf Signed-off-by: Andreas Herrmann Signed-off-by: Dave Jones --- arch/x86/kernel/cpu/cpufreq/powernow-k8.c | 18 +++++++++++++++--- arch/x86/kernel/cpu/cpufreq/powernow-k8.h | 17 ++++++++++++++++- 2 files changed, 31 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/cpu/cpufreq/powernow-k8.c b/arch/x86/kernel/cpu/cpufreq/powernow-k8.c index d3dcd58..7f05f44 100644 --- a/arch/x86/kernel/cpu/cpufreq/powernow-k8.c +++ b/arch/x86/kernel/cpu/cpufreq/powernow-k8.c @@ -115,9 +115,20 @@ static int query_current_values_with_pending_wait(struct powernow_k8_data *data) u32 i = 0; if (cpu_family == CPU_HW_PSTATE) { - rdmsr(MSR_PSTATE_STATUS, lo, hi); - i = lo & HW_PSTATE_MASK; - data->currpstate = i; + if (data->currpstate == HW_PSTATE_INVALID) { + /* read (initial) hw pstate if not yet set */ + rdmsr(MSR_PSTATE_STATUS, lo, hi); + i = lo & HW_PSTATE_MASK; + + /* + * a workaround for family 11h erratum 311 might cause + * an "out-of-range Pstate if the core is in Pstate-0 + */ + if (i >= data->numps) + data->currpstate = HW_PSTATE_0; + else + data->currpstate = i; + } return 0; } do { @@ -1121,6 +1132,7 @@ static int __cpuinit powernowk8_cpu_init(struct cpufreq_policy *pol) } data->cpu = pol->cpu; + data->currpstate = HW_PSTATE_INVALID; if (powernow_k8_cpu_init_acpi(data)) { /* diff --git a/arch/x86/kernel/cpu/cpufreq/powernow-k8.h b/arch/x86/kernel/cpu/cpufreq/powernow-k8.h index ab48cfe..65cfb5d 100644 --- a/arch/x86/kernel/cpu/cpufreq/powernow-k8.h +++ b/arch/x86/kernel/cpu/cpufreq/powernow-k8.h @@ -5,6 +5,19 @@ * http://www.gnu.org/licenses/gpl.html */ + +enum pstate { + HW_PSTATE_INVALID = 0xff, + HW_PSTATE_0 = 0, + HW_PSTATE_1 = 1, + HW_PSTATE_2 = 2, + HW_PSTATE_3 = 3, + HW_PSTATE_4 = 4, + HW_PSTATE_5 = 5, + HW_PSTATE_6 = 6, + HW_PSTATE_7 = 7, +}; + struct powernow_k8_data { unsigned int cpu; @@ -23,7 +36,9 @@ struct powernow_k8_data { u32 exttype; /* extended interface = 1 */ /* keep track of the current fid / vid or pstate */ - u32 currvid, currfid, currpstate; + u32 currvid; + u32 currfid; + enum pstate currpstate; /* the powernow_table includes all frequency and vid/fid pairings: * fid are the lower 8 bits of the index, vid are the upper 8 bits. -- cgit v1.1 From 147dcf5489fb86c4bfe400520186f9f11b304783 Mon Sep 17 00:00:00 2001 From: Amit Kucheria Date: Tue, 25 Nov 2008 15:11:12 -0800 Subject: ARM: OMAP: Typo fix for clock_allow_idle The second clk_deny_idle instance should be clk_allow_idle instead. Signed-off-by: Amit Kucheria Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/include/mach/pm.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-omap/include/mach/pm.h b/arch/arm/plat-omap/include/mach/pm.h index 768eb6e..2a9c27a 100644 --- a/arch/arm/plat-omap/include/mach/pm.h +++ b/arch/arm/plat-omap/include/mach/pm.h @@ -128,7 +128,7 @@ void clk_deny_idle(struct clk *clk); * clk_allow_idle - Counters previous clk_deny_idle * @clk: clock signal handle */ -void clk_deny_idle(struct clk *clk); +void clk_allow_idle(struct clk *clk); extern void omap_pm_idle(void); extern void omap_pm_suspend(void); -- cgit v1.1 From ffd565a8b817d1eb4b25184e8418e8d96c3f56f6 Mon Sep 17 00:00:00 2001 From: Andreas Herrmann Date: Tue, 25 Nov 2008 17:18:03 +0100 Subject: x86: fixup config space size of CPU functions for AMD family 11h Impact: extend allowed configuration space access on 11h CPUs from 256 to 4K Signed-off-by: Andreas Herrmann Acked-by: Jesse Barnes Signed-off-by: Ingo Molnar --- arch/x86/pci/fixup.c | 25 ++++++++++++++----------- 1 file changed, 14 insertions(+), 11 deletions(-) (limited to 'arch') diff --git a/arch/x86/pci/fixup.c b/arch/x86/pci/fixup.c index 3c27a80..2051dc9 100644 --- a/arch/x86/pci/fixup.c +++ b/arch/x86/pci/fixup.c @@ -496,21 +496,24 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SIEMENS, 0x0015, pci_siemens_interrupt_controller); /* - * Regular PCI devices have 256 bytes, but AMD Family 10h Opteron ext config - * have 4096 bytes. Even if the device is capable, that doesn't mean we can - * access it. Maybe we don't have a way to generate extended config space - * accesses. So check it + * Regular PCI devices have 256 bytes, but AMD Family 10h/11h CPUs have + * 4096 bytes configuration space for each function of their processor + * configuration space. */ -static void fam10h_pci_cfg_space_size(struct pci_dev *dev) +static void amd_cpu_pci_cfg_space_size(struct pci_dev *dev) { dev->cfg_size = pci_cfg_space_size_ext(dev); } - -DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1200, fam10h_pci_cfg_space_size); -DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1201, fam10h_pci_cfg_space_size); -DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1202, fam10h_pci_cfg_space_size); -DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1203, fam10h_pci_cfg_space_size); -DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1204, fam10h_pci_cfg_space_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1200, amd_cpu_pci_cfg_space_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1201, amd_cpu_pci_cfg_space_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1202, amd_cpu_pci_cfg_space_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1203, amd_cpu_pci_cfg_space_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1204, amd_cpu_pci_cfg_space_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1300, amd_cpu_pci_cfg_space_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1301, amd_cpu_pci_cfg_space_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1302, amd_cpu_pci_cfg_space_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1303, amd_cpu_pci_cfg_space_size); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, 0x1304, amd_cpu_pci_cfg_space_size); /* * SB600: Disable BAR1 on device 14.0 to avoid HPET resources from -- cgit v1.1 From 72e9622c2a2eb73d82c716504cc93d22cd3cfd8e Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Tue, 25 Nov 2008 18:57:08 +0100 Subject: [ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data 0 is a valid GPIO number, use a negative number to specify, that this camera doesn't have a GPIO for bus-width switching. Signed-off-by: Guennadi Liakhovetski Signed-off-by: Eric Miao --- arch/arm/mach-pxa/pcm990-baseboard.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c index f601425..b36cec5c 100644 --- a/arch/arm/mach-pxa/pcm990-baseboard.c +++ b/arch/arm/mach-pxa/pcm990-baseboard.c @@ -385,6 +385,7 @@ static struct soc_camera_link iclink[] = { .gpio = NR_BUILTIN_GPIO + 1, }, { .bus_id = 0, /* Must match with the camera ID above */ + .gpio = -ENXIO, } }; -- cgit v1.1 From 2fd36a5d6e830269a37f0f6ccfd34ee0517ebc7d Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Wed, 26 Nov 2008 12:51:42 +0800 Subject: [ARM] pxa/corgi: update default config to exclude tosa from being built Signed-off-by: Eric Miao --- arch/arm/configs/corgi_defconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/configs/corgi_defconfig b/arch/arm/configs/corgi_defconfig index f3af0b5..9876543 100644 --- a/arch/arm/configs/corgi_defconfig +++ b/arch/arm/configs/corgi_defconfig @@ -179,7 +179,7 @@ CONFIG_MACH_HUSKY=y # CONFIG_MACH_AKITA is not set # CONFIG_MACH_SPITZ is not set # CONFIG_MACH_BORZOI is not set -CONFIG_MACH_TOSA=y +# CONFIG_MACH_TOSA is not set # CONFIG_ARCH_VIPER is not set # CONFIG_ARCH_PXA_ESERIES is not set # CONFIG_TRIZEPS_PXA is not set -- cgit v1.1 From 6c475352e87224a8f0b8cc6f6cc96b30563dc5b4 Mon Sep 17 00:00:00 2001 From: Marcelo Tosatti Date: Tue, 25 Nov 2008 15:33:10 +0100 Subject: KVM: MMU: avoid creation of unreachable pages in the shadow It is possible for a shadow page to have a parent link pointing to a freed page. When zapping a high level table, kvm_mmu_page_unlink_children fails to remove the parent_pte link. For that to happen, the child must be unreachable via the shadow tree, which can happen in shadow_walk_entry if the guest pte was modified in between walk() and fetch(). Remove the parent pte reference in such case. Possible cause for oops in bug #2217430. Signed-off-by: Marcelo Tosatti Signed-off-by: Avi Kivity --- arch/x86/kvm/paging_tmpl.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/x86/kvm/paging_tmpl.h b/arch/x86/kvm/paging_tmpl.h index 613ec9a..84eee43 100644 --- a/arch/x86/kvm/paging_tmpl.h +++ b/arch/x86/kvm/paging_tmpl.h @@ -331,6 +331,7 @@ static int FNAME(shadow_walk_entry)(struct kvm_shadow_walk *_sw, r = kvm_read_guest_atomic(vcpu->kvm, gw->pte_gpa[level - 2], &curr_pte, sizeof(curr_pte)); if (r || curr_pte != gw->ptes[level - 2]) { + kvm_mmu_put_page(shadow_page, sptep); kvm_release_pfn_clean(sw->pfn); sw->sptep = NULL; return 1; -- cgit v1.1 From 9860d1b08b082ffb54c4b7827c48c2728e12ba21 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Sun, 16 Nov 2008 12:04:13 +0100 Subject: parisc: __kernel_time_t is always long __kernel_time_t is always long on PA-RISC, irrespective of CONFIG_64BIT, hence move it out of the #ifdef CONFIG_64BIT / #else / #endif block. Signed-off-by: Geert Uytterhoeven Signed-off-by: Kyle McMartin --- arch/parisc/include/asm/posix_types.h | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/parisc/include/asm/posix_types.h b/arch/parisc/include/asm/posix_types.h index bb725a6..00da29a 100644 --- a/arch/parisc/include/asm/posix_types.h +++ b/arch/parisc/include/asm/posix_types.h @@ -24,13 +24,12 @@ typedef int __kernel_daddr_t; typedef unsigned long __kernel_size_t; typedef long __kernel_ssize_t; typedef long __kernel_ptrdiff_t; -typedef long __kernel_time_t; #else typedef unsigned int __kernel_size_t; typedef int __kernel_ssize_t; typedef int __kernel_ptrdiff_t; -typedef long __kernel_time_t; #endif +typedef long __kernel_time_t; typedef char * __kernel_caddr_t; typedef unsigned short __kernel_uid16_t; -- cgit v1.1 From 7a3f5134a8f5bd7fa38b5645eef05e8a4eb62951 Mon Sep 17 00:00:00 2001 From: Helge Deller Date: Wed, 26 Nov 2008 12:46:22 -0800 Subject: parisc: fix kernel crash when unwinding a userspace process Any user on existing parisc 32- and 64bit-kernels can easily crash the kernel and as such enforce a DSO. A simple testcase is available here: http://gsyprf10.external.hp.com/~deller/crash.tgz The problem is introduced by the fact, that the handle_interruption() crash handler calls the show_regs() function, which in turn tries to unwind the stack by calling parisc_show_stack(). Since the stack contains userspace addresses, a try to unwind the stack is dangerous and useless and leads to the crash. The fix is trivial: For userspace processes a) avoid to unwind the stack, and b) avoid to resolve userspace addresses to kernel symbol names. While touching this code, I converted print_symbol() to %pS printk formats and made parisc_show_stack() static. An initial patch for this was written by Kyle McMartin back in August: http://marc.info/?l=linux-parisc&m=121805168830283&w=2 Compile and run-tested with a 64bit parisc kernel. Signed-off-by: Helge Deller Cc: Grant Grundler Cc: Matthew Wilcox Cc: [2.6.25.x, 2.6.26.x, 2.6.27.x, earlier...] Signed-off-by: Andrew Morton Signed-off-by: Kyle McMartin --- arch/parisc/kernel/traps.c | 43 +++++++++++++++++++++---------------------- 1 file changed, 21 insertions(+), 22 deletions(-) (limited to 'arch') diff --git a/arch/parisc/kernel/traps.c b/arch/parisc/kernel/traps.c index 675f1d0..4c771cd 100644 --- a/arch/parisc/kernel/traps.c +++ b/arch/parisc/kernel/traps.c @@ -24,7 +24,6 @@ #include #include #include -#include #include #include @@ -51,7 +50,7 @@ DEFINE_SPINLOCK(pa_dbit_lock); #endif -void parisc_show_stack(struct task_struct *t, unsigned long *sp, +static void parisc_show_stack(struct task_struct *task, unsigned long *sp, struct pt_regs *regs); static int printbinary(char *buf, unsigned long x, int nbits) @@ -121,18 +120,19 @@ static void print_fr(char *level, struct pt_regs *regs) void show_regs(struct pt_regs *regs) { - int i; + int i, user; char *level; unsigned long cr30, cr31; - level = user_mode(regs) ? KERN_DEBUG : KERN_CRIT; + user = user_mode(regs); + level = user ? KERN_DEBUG : KERN_CRIT; print_gr(level, regs); for (i = 0; i < 8; i += 4) PRINTREGS(level, regs->sr, "sr", RFMT, i); - if (user_mode(regs)) + if (user) print_fr(level, regs); cr30 = mfctl(30); @@ -145,14 +145,18 @@ void show_regs(struct pt_regs *regs) printk("%s CPU: %8d CR30: " RFMT " CR31: " RFMT "\n", level, current_thread_info()->cpu, cr30, cr31); printk("%s ORIG_R28: " RFMT "\n", level, regs->orig_r28); - printk(level); - print_symbol(" IAOQ[0]: %s\n", regs->iaoq[0]); - printk(level); - print_symbol(" IAOQ[1]: %s\n", regs->iaoq[1]); - printk(level); - print_symbol(" RP(r2): %s\n", regs->gr[2]); - - parisc_show_stack(current, NULL, regs); + + if (user) { + printk("%s IAOQ[0]: " RFMT "\n", level, regs->iaoq[0]); + printk("%s IAOQ[1]: " RFMT "\n", level, regs->iaoq[1]); + printk("%s RP(r2): " RFMT "\n", level, regs->gr[2]); + } else { + printk("%s IAOQ[0]: %pS\n", level, (void *) regs->iaoq[0]); + printk("%s IAOQ[1]: %pS\n", level, (void *) regs->iaoq[1]); + printk("%s RP(r2): %pS\n", level, (void *) regs->gr[2]); + + parisc_show_stack(current, NULL, regs); + } } @@ -173,20 +177,15 @@ static void do_show_stack(struct unwind_frame_info *info) break; if (__kernel_text_address(info->ip)) { - printk("%s [<" RFMT ">] ", (i&0x3)==1 ? KERN_CRIT : "", info->ip); -#ifdef CONFIG_KALLSYMS - print_symbol("%s\n", info->ip); -#else - if ((i & 0x03) == 0) - printk("\n"); -#endif + printk(KERN_CRIT " [<" RFMT ">] %pS\n", + info->ip, (void *) info->ip); i++; } } - printk("\n"); + printk(KERN_CRIT "\n"); } -void parisc_show_stack(struct task_struct *task, unsigned long *sp, +static void parisc_show_stack(struct task_struct *task, unsigned long *sp, struct pt_regs *regs) { struct unwind_frame_info info; -- cgit v1.1 From 90f671301a5e2678cdc99f611cd842161c3bb87f Mon Sep 17 00:00:00 2001 From: Kay Sievers Date: Fri, 7 Nov 2008 01:42:46 +0100 Subject: parisc: struct device - replace bus_id with dev_name(), dev_set_name() (I did not compile or test it, please let me know, or help fixing it, if something is wrong with the conversion) This patch is part of a larger patch series which will remove the "char bus_id[20]" name string from struct device. The device name is managed in the kobject anyway, and without any size limitation, and just needlessly copied into "struct device". To set and read the device name dev_name(dev) and dev_set_name(dev) must be used. If your code uses static kobjects, which it shouldn't do, "const char *init_name" can be used to statically provide the name the registered device should have. At registration time, the init_name field is cleared, to enforce the use of dev_name(dev) to access the device name at a later time. We need to get rid of all occurrences of bus_id in the entire tree to be able to enable the new interface. Please apply this patch, and possibly convert any remaining remaining occurrences of bus_id. We want to submit a patch to -next, which will remove bus_id from "struct device", to find the remaining pieces to convert, and finally switch over to the new api, which will remove the 20 bytes array and does no longer have a size limitation. Thanks, Kay Cc: Matthew Wilcox Cc: linux-parisc@vger.kernel.org Acked-by: Greg Kroah-Hartman Signed-off-by: Kay Sievers Signed-off-by: Kyle McMartin --- arch/parisc/include/asm/parisc-device.h | 4 ++-- arch/parisc/kernel/drivers.c | 6 ++++-- 2 files changed, 6 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/parisc/include/asm/parisc-device.h b/arch/parisc/include/asm/parisc-device.h index 7aa13f2..9afdad6 100644 --- a/arch/parisc/include/asm/parisc-device.h +++ b/arch/parisc/include/asm/parisc-device.h @@ -42,9 +42,9 @@ struct parisc_driver { #define to_parisc_driver(d) container_of(d, struct parisc_driver, drv) #define parisc_parent(d) to_parisc_device(d->dev.parent) -static inline char *parisc_pathname(struct parisc_device *d) +static inline const char *parisc_pathname(struct parisc_device *d) { - return d->dev.bus_id; + return dev_name(&d->dev); } static inline void diff --git a/arch/parisc/kernel/drivers.c b/arch/parisc/kernel/drivers.c index 2ca654b..884b7ce 100644 --- a/arch/parisc/kernel/drivers.c +++ b/arch/parisc/kernel/drivers.c @@ -43,7 +43,7 @@ struct hppa_dma_ops *hppa_dma_ops __read_mostly; EXPORT_SYMBOL(hppa_dma_ops); static struct device root = { - .bus_id = "parisc", + .init_name = "parisc", }; static inline int check_dev(struct device *dev) @@ -393,7 +393,8 @@ EXPORT_SYMBOL(print_pci_hwpath); static void setup_bus_id(struct parisc_device *padev) { struct hardware_path path; - char *output = padev->dev.bus_id; + char name[20]; + char *output = name; int i; get_node_path(padev->dev.parent, &path); @@ -404,6 +405,7 @@ static void setup_bus_id(struct parisc_device *padev) output += sprintf(output, "%u:", (unsigned char) path.bc[i]); } sprintf(output, "%u", (unsigned char) padev->hw_path); + dev_set_name(&padev->dev, name); } struct parisc_device * create_tree_node(char id, struct device *parent) -- cgit v1.1 From 723fdb781abfe78d8ba7d911abbb581722348aa7 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Wed, 26 Nov 2008 14:35:16 -0800 Subject: ARM: OMAP: Fixes for suspend / resume GPIO wake-up handling Use the correct wake-up enable register, and make it work with 34xx also. Signed-off-by: Tero Kristo Signed-off-by: Kevin Hilman Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/gpio.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c index 8679fbc..424049d 100644 --- a/arch/arm/plat-omap/gpio.c +++ b/arch/arm/plat-omap/gpio.c @@ -101,6 +101,7 @@ #define OMAP24XX_GPIO_IRQSTATUS2 0x0028 #define OMAP24XX_GPIO_IRQENABLE2 0x002c #define OMAP24XX_GPIO_IRQENABLE1 0x001c +#define OMAP24XX_GPIO_WAKE_EN 0x0020 #define OMAP24XX_GPIO_CTRL 0x0030 #define OMAP24XX_GPIO_OE 0x0034 #define OMAP24XX_GPIO_DATAIN 0x0038 @@ -1551,7 +1552,7 @@ static int omap_gpio_suspend(struct sys_device *dev, pm_message_t mesg) #endif #if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) case METHOD_GPIO_24XX: - wake_status = bank->base + OMAP24XX_GPIO_SETWKUENA; + wake_status = bank->base + OMAP24XX_GPIO_WAKE_EN; wake_clear = bank->base + OMAP24XX_GPIO_CLEARWKUENA; wake_set = bank->base + OMAP24XX_GPIO_SETWKUENA; break; @@ -1574,7 +1575,7 @@ static int omap_gpio_resume(struct sys_device *dev) { int i; - if (!cpu_is_omap24xx() && !cpu_is_omap16xx()) + if (!cpu_class_is_omap2() && !cpu_is_omap16xx()) return 0; for (i = 0; i < gpio_bank_count; i++) { -- cgit v1.1 From 59da21398e680e8100625d689c8bebee6a139e93 Mon Sep 17 00:00:00 2001 From: Martin Schwidefsky Date: Thu, 27 Nov 2008 11:05:55 +0100 Subject: [S390] fix system call parameter functions. syscall_get_nr() currently returns a valid result only if the call chain of the traced process includes do_syscall_trace_enter(). But collect_syscall() can be called for any sleeping task, the result of syscall_get_nr() in general is completely bogus. To make syscall_get_nr() work for any sleeping task the traps field in pt_regs is replace with svcnr - the system call number the process is executing. If svcnr == 0 the process is not on a system call path. The syscall_get_arguments and syscall_set_arguments use regs->gprs[2] for the first system call parameter. This is incorrect since gprs[2] may have been overwritten with the system call number if the call chain includes do_syscall_trace_enter. Use regs->orig_gprs2 instead. Signed-off-by: Martin Schwidefsky --- arch/s390/include/asm/ptrace.h | 2 +- arch/s390/include/asm/syscall.h | 28 ++++++++++++++++------------ arch/s390/kernel/asm-offsets.c | 2 +- arch/s390/kernel/compat_signal.c | 2 +- arch/s390/kernel/entry.S | 21 +++++++++++---------- arch/s390/kernel/entry64.S | 23 ++++++++++------------- arch/s390/kernel/ptrace.c | 2 +- arch/s390/kernel/signal.c | 6 +++--- 8 files changed, 44 insertions(+), 42 deletions(-) (limited to 'arch') diff --git a/arch/s390/include/asm/ptrace.h b/arch/s390/include/asm/ptrace.h index a7226f8..fb0ca47 100644 --- a/arch/s390/include/asm/ptrace.h +++ b/arch/s390/include/asm/ptrace.h @@ -321,8 +321,8 @@ struct pt_regs psw_t psw; unsigned long gprs[NUM_GPRS]; unsigned long orig_gpr2; + unsigned short svcnr; unsigned short ilc; - unsigned short trap; }; #endif diff --git a/arch/s390/include/asm/syscall.h b/arch/s390/include/asm/syscall.h index 6e62397..2429b87 100644 --- a/arch/s390/include/asm/syscall.h +++ b/arch/s390/include/asm/syscall.h @@ -17,9 +17,7 @@ static inline long syscall_get_nr(struct task_struct *task, struct pt_regs *regs) { - if (regs->trap != __LC_SVC_OLD_PSW) - return -1; - return regs->gprs[2]; + return regs->svcnr ? regs->svcnr : -1; } static inline void syscall_rollback(struct task_struct *task, @@ -52,18 +50,20 @@ static inline void syscall_get_arguments(struct task_struct *task, unsigned int i, unsigned int n, unsigned long *args) { + unsigned long mask = -1UL; + BUG_ON(i + n > 6); #ifdef CONFIG_COMPAT - if (test_tsk_thread_flag(task, TIF_31BIT)) { - if (i + n == 6) - args[--n] = (u32) regs->args[0]; - while (n-- > 0) - args[n] = (u32) regs->gprs[2 + i + n]; - } + if (test_tsk_thread_flag(task, TIF_31BIT)) + mask = 0xffffffff; #endif if (i + n == 6) - args[--n] = regs->args[0]; - memcpy(args, ®s->gprs[2 + i], n * sizeof(args[0])); + args[--n] = regs->args[0] & mask; + while (n-- > 0) + if (i + n > 0) + args[n] = regs->gprs[2 + i + n] & mask; + if (i == 0) + args[0] = regs->orig_gpr2 & mask; } static inline void syscall_set_arguments(struct task_struct *task, @@ -74,7 +74,11 @@ static inline void syscall_set_arguments(struct task_struct *task, BUG_ON(i + n > 6); if (i + n == 6) regs->args[0] = args[--n]; - memcpy(®s->gprs[2 + i], args, n * sizeof(args[0])); + while (n-- > 0) + if (i + n > 0) + regs->gprs[2 + i + n] = args[n]; + if (i == 0) + regs->orig_gpr2 = args[0]; } #endif /* _ASM_SYSCALL_H */ diff --git a/arch/s390/kernel/asm-offsets.c b/arch/s390/kernel/asm-offsets.c index fa28eca..3d144e6 100644 --- a/arch/s390/kernel/asm-offsets.c +++ b/arch/s390/kernel/asm-offsets.c @@ -32,7 +32,7 @@ int main(void) DEFINE(__PT_GPRS, offsetof(struct pt_regs, gprs)); DEFINE(__PT_ORIG_GPR2, offsetof(struct pt_regs, orig_gpr2)); DEFINE(__PT_ILC, offsetof(struct pt_regs, ilc)); - DEFINE(__PT_TRAP, offsetof(struct pt_regs, trap)); + DEFINE(__PT_SVCNR, offsetof(struct pt_regs, svcnr)); DEFINE(__PT_SIZE, sizeof(struct pt_regs)); BLANK(); DEFINE(__SF_BACKCHAIN, offsetof(struct stack_frame, back_chain)); diff --git a/arch/s390/kernel/compat_signal.c b/arch/s390/kernel/compat_signal.c index c7f02e7..b537cb0 100644 --- a/arch/s390/kernel/compat_signal.c +++ b/arch/s390/kernel/compat_signal.c @@ -340,7 +340,7 @@ static int restore_sigregs32(struct pt_regs *regs,_sigregs32 __user *sregs) return err; restore_fp_regs(¤t->thread.fp_regs); - regs->trap = -1; /* disable syscall checks */ + regs->svcnr = 0; /* disable syscall checks */ return 0; } diff --git a/arch/s390/kernel/entry.S b/arch/s390/kernel/entry.S index 08844fc..198ea18 100644 --- a/arch/s390/kernel/entry.S +++ b/arch/s390/kernel/entry.S @@ -46,7 +46,7 @@ SP_R14 = STACK_FRAME_OVERHEAD + __PT_GPRS + 56 SP_R15 = STACK_FRAME_OVERHEAD + __PT_GPRS + 60 SP_ORIG_R2 = STACK_FRAME_OVERHEAD + __PT_ORIG_GPR2 SP_ILC = STACK_FRAME_OVERHEAD + __PT_ILC -SP_TRAP = STACK_FRAME_OVERHEAD + __PT_TRAP +SP_SVCNR = STACK_FRAME_OVERHEAD + __PT_SVCNR SP_SIZE = STACK_FRAME_OVERHEAD + __PT_SIZE _TIF_WORK_SVC = (_TIF_SIGPENDING | _TIF_NOTIFY_RESUME | _TIF_NEED_RESCHED | \ @@ -183,11 +183,10 @@ STACK_SIZE = 1 << STACK_SHIFT .macro CREATE_STACK_FRAME psworg,savearea s %r15,BASED(.Lc_spsize) # make room for registers & psw mvc SP_PSW(8,%r15),0(%r12) # move user PSW to stack - la %r12,\psworg st %r2,SP_ORIG_R2(%r15) # store original content of gpr 2 - icm %r12,12,__LC_SVC_ILC + icm %r12,3,__LC_SVC_ILC stm %r0,%r11,SP_R0(%r15) # store gprs %r0-%r11 to kernel stack - st %r12,SP_ILC(%r15) + st %r12,SP_SVCNR(%r15) mvc SP_R12(16,%r15),\savearea # move %r12-%r15 to stack la %r12,0 st %r12,__SF_BACKCHAIN(%r15) # clear back chain @@ -264,16 +263,17 @@ sysc_update: #endif sysc_do_svc: l %r9,__LC_THREAD_INFO # load pointer to thread_info struct - sla %r7,2 # *4 and test for svc 0 + ltr %r7,%r7 # test for svc 0 bnz BASED(sysc_nr_ok) # svc number > 0 # svc 0: system call number in %r1 cl %r1,BASED(.Lnr_syscalls) bnl BASED(sysc_nr_ok) lr %r7,%r1 # copy svc number to %r7 - sla %r7,2 # *4 sysc_nr_ok: mvc SP_ARGS(4,%r15),SP_R7(%r15) sysc_do_restart: + sth %r7,SP_SVCNR(%r15) + sll %r7,2 # svc number *4 l %r8,BASED(.Lsysc_table) tm __TI_flags+3(%r9),(_TIF_SYSCALL_TRACE|_TIF_SYSCALL_AUDIT) l %r8,0(%r7,%r8) # get system call addr. @@ -376,7 +376,6 @@ sysc_notify_resume: sysc_restart: ni __TI_flags+3(%r9),255-_TIF_RESTART_SVC # clear TIF_RESTART_SVC l %r7,SP_R2(%r15) # load new svc number - sla %r7,2 mvc SP_R2(4,%r15),SP_ORIG_R2(%r15) # restore first argument lm %r2,%r6,SP_R2(%r15) # load svc arguments b BASED(sysc_do_restart) # restart svc @@ -386,7 +385,8 @@ sysc_restart: # sysc_singlestep: ni __TI_flags+3(%r9),255-_TIF_SINGLE_STEP # clear TIF_SINGLE_STEP - mvi SP_TRAP+1(%r15),0x28 # set trap indication to pgm check + mvi SP_SVCNR(%r15),0xff # set trap indication to pgm check + mvi SP_SVCNR+1(%r15),0xff la %r2,SP_PTREGS(%r15) # address of register-save area l %r1,BASED(.Lhandle_per) # load adr. of per handler la %r14,BASED(sysc_return) # load adr. of system return @@ -407,7 +407,7 @@ sysc_tracesys: bnl BASED(sysc_tracenogo) l %r8,BASED(.Lsysc_table) lr %r7,%r2 - sll %r7,2 # *4 + sll %r7,2 # svc number *4 l %r8,0(%r7,%r8) sysc_tracego: lm %r3,%r6,SP_R3(%r15) @@ -586,7 +586,8 @@ pgm_svcper: # per was called from kernel, must be kprobes # kernel_per: - mvi SP_TRAP+1(%r15),0x28 # set trap indication to pgm check + mvi SP_SVCNR(%r15),0xff # set trap indication to pgm check + mvi SP_SVCNR+1(%r15),0xff la %r2,SP_PTREGS(%r15) # address of register-save area l %r1,BASED(.Lhandle_per) # load adr. of per handler la %r14,BASED(sysc_restore)# load adr. of system return diff --git a/arch/s390/kernel/entry64.S b/arch/s390/kernel/entry64.S index 41aca06..89c121a 100644 --- a/arch/s390/kernel/entry64.S +++ b/arch/s390/kernel/entry64.S @@ -46,7 +46,7 @@ SP_R14 = STACK_FRAME_OVERHEAD + __PT_GPRS + 112 SP_R15 = STACK_FRAME_OVERHEAD + __PT_GPRS + 120 SP_ORIG_R2 = STACK_FRAME_OVERHEAD + __PT_ORIG_GPR2 SP_ILC = STACK_FRAME_OVERHEAD + __PT_ILC -SP_TRAP = STACK_FRAME_OVERHEAD + __PT_TRAP +SP_SVCNR = STACK_FRAME_OVERHEAD + __PT_SVCNR SP_SIZE = STACK_FRAME_OVERHEAD + __PT_SIZE STACK_SHIFT = PAGE_SHIFT + THREAD_ORDER @@ -171,11 +171,10 @@ _TIF_WORK_INT = (_TIF_SIGPENDING | _TIF_NOTIFY_RESUME | _TIF_NEED_RESCHED | \ .macro CREATE_STACK_FRAME psworg,savearea aghi %r15,-SP_SIZE # make room for registers & psw mvc SP_PSW(16,%r15),0(%r12) # move user PSW to stack - la %r12,\psworg stg %r2,SP_ORIG_R2(%r15) # store original content of gpr 2 - icm %r12,12,__LC_SVC_ILC + icm %r12,3,__LC_SVC_ILC stmg %r0,%r11,SP_R0(%r15) # store gprs %r0-%r11 to kernel stack - st %r12,SP_ILC(%r15) + st %r12,SP_SVCNR(%r15) mvc SP_R12(32,%r15),\savearea # move %r12-%r15 to stack la %r12,0 stg %r12,__SF_BACKCHAIN(%r15) @@ -250,16 +249,17 @@ sysc_update: #endif sysc_do_svc: lg %r9,__LC_THREAD_INFO # load pointer to thread_info struct - slag %r7,%r7,2 # *4 and test for svc 0 + ltgr %r7,%r7 # test for svc 0 jnz sysc_nr_ok # svc 0: system call number in %r1 cl %r1,BASED(.Lnr_syscalls) jnl sysc_nr_ok lgfr %r7,%r1 # clear high word in r1 - slag %r7,%r7,2 # svc 0: system call number in %r1 sysc_nr_ok: mvc SP_ARGS(8,%r15),SP_R7(%r15) sysc_do_restart: + sth %r7,SP_SVCNR(%r15) + sllg %r7,%r7,2 # svc number * 4 larl %r10,sys_call_table #ifdef CONFIG_COMPAT tm __TI_flags+5(%r9),(_TIF_31BIT>>16) # running in 31 bit mode ? @@ -363,7 +363,6 @@ sysc_notify_resume: sysc_restart: ni __TI_flags+7(%r9),255-_TIF_RESTART_SVC # clear TIF_RESTART_SVC lg %r7,SP_R2(%r15) # load new svc number - slag %r7,%r7,2 # *4 mvc SP_R2(8,%r15),SP_ORIG_R2(%r15) # restore first argument lmg %r2,%r6,SP_R2(%r15) # load svc arguments j sysc_do_restart # restart svc @@ -372,9 +371,8 @@ sysc_restart: # _TIF_SINGLE_STEP is set, call do_single_step # sysc_singlestep: - ni __TI_flags+7(%r9),255-_TIF_SINGLE_STEP # clear TIF_SINGLE_STEP - lhi %r0,__LC_PGM_OLD_PSW - sth %r0,SP_TRAP(%r15) # set trap indication to pgm check + ni __TI_flags+7(%r9),255-_TIF_SINGLE_STEP # clear TIF_SINGLE_STEP + xc SP_SVCNR(2,%r15),SP_SVCNR(%r15) # clear svc number la %r2,SP_PTREGS(%r15) # address of register-save area larl %r14,sysc_return # load adr. of system return jg do_single_step # branch to do_sigtrap @@ -392,7 +390,7 @@ sysc_tracesys: lghi %r0,NR_syscalls clgr %r0,%r2 jnh sysc_tracenogo - slag %r7,%r2,2 # *4 + sllg %r7,%r2,2 # svc number *4 lgf %r8,0(%r7,%r10) sysc_tracego: lmg %r3,%r6,SP_R3(%r15) @@ -567,8 +565,7 @@ pgm_svcper: # per was called from kernel, must be kprobes # kernel_per: - lhi %r0,__LC_PGM_OLD_PSW - sth %r0,SP_TRAP(%r15) # set trap indication to pgm check + xc SP_SVCNR(2,%r15),SP_SVCNR(%r15) # clear svc number la %r2,SP_PTREGS(%r15) # address of register-save area larl %r14,sysc_restore # load adr. of system ret, no work jg do_single_step # branch to do_single_step diff --git a/arch/s390/kernel/ptrace.c b/arch/s390/kernel/ptrace.c index 1f31be1..38ff2bc 100644 --- a/arch/s390/kernel/ptrace.c +++ b/arch/s390/kernel/ptrace.c @@ -657,7 +657,7 @@ asmlinkage long do_syscall_trace_enter(struct pt_regs *regs) * debugger stored an invalid system call number. Skip * the system call and the system call restart handling. */ - regs->trap = -1; + regs->svcnr = 0; ret = -1; } diff --git a/arch/s390/kernel/signal.c b/arch/s390/kernel/signal.c index 4f7fc30..8e6812a 100644 --- a/arch/s390/kernel/signal.c +++ b/arch/s390/kernel/signal.c @@ -160,7 +160,7 @@ static int restore_sigregs(struct pt_regs *regs, _sigregs __user *sregs) current->thread.fp_regs.fpc &= FPC_VALID_MASK; restore_fp_regs(¤t->thread.fp_regs); - regs->trap = -1; /* disable syscall checks */ + regs->svcnr = 0; /* disable syscall checks */ return 0; } @@ -445,7 +445,7 @@ void do_signal(struct pt_regs *regs) oldset = ¤t->blocked; /* Are we from a system call? */ - if (regs->trap == __LC_SVC_OLD_PSW) { + if (regs->svcnr) { continue_addr = regs->psw.addr; restart_addr = continue_addr - regs->ilc; retval = regs->gprs[2]; @@ -462,7 +462,7 @@ void do_signal(struct pt_regs *regs) case -ERESTART_RESTARTBLOCK: regs->gprs[2] = -EINTR; } - regs->trap = -1; /* Don't deal with this again. */ + regs->svcnr = 0; /* Don't deal with this again. */ } /* Get signal to deliver. When running under ptrace, at this point -- cgit v1.1 From 8107d8296baff899db89c1716fe8af69a5b19d18 Mon Sep 17 00:00:00 2001 From: Christian Borntraeger Date: Thu, 27 Nov 2008 11:05:56 +0100 Subject: [S390] fix/cleanup sched_clock CONFIG_PRINTK_TIME reveals that sched_clock has a wrong offset during boot: .. [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 775679 [ 0.000000] Kernel command line: dasd=4b6c root=/dev/dasda1 ro noinitrd [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [6920575.975232] console [ttyS0] enabled [6920575.987586] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [6920575.991404] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) .. The s390 implementation of sched_clock uses the store clock instruction and subtracts jiffies_timer_cc. jiffies_timer_cc is a local variable in arch/s390/kernel/time.c and only used for sched_clock and monotonic clock. For historical reasons there is an offset on that value. With todays code this offset is unnecessary. By removing that offset we can get a sched_clock which returns the nanoseconds after time_init. This improves CONFIG_PRINTK_TIME. Since sched_clock is the only user, I have also renamed jiffies_timer_cc to sched_clock_base_cc. In addition, the local variable init_timer_cc is redundant and can be romved as well. Signed-off-by: Christian Borntraeger Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/time.c | 13 +++++-------- 1 file changed, 5 insertions(+), 8 deletions(-) (limited to 'arch') diff --git a/arch/s390/kernel/time.c b/arch/s390/kernel/time.c index b94e9e3..eccefbb 100644 --- a/arch/s390/kernel/time.c +++ b/arch/s390/kernel/time.c @@ -59,7 +59,7 @@ static ext_int_info_t ext_int_info_cc; static ext_int_info_t ext_int_etr_cc; -static u64 jiffies_timer_cc; +static u64 sched_clock_base_cc; static DEFINE_PER_CPU(struct clock_event_device, comparators); @@ -68,7 +68,7 @@ static DEFINE_PER_CPU(struct clock_event_device, comparators); */ unsigned long long sched_clock(void) { - return ((get_clock_xt() - jiffies_timer_cc) * 125) >> 9; + return ((get_clock_xt() - sched_clock_base_cc) * 125) >> 9; } /* @@ -229,13 +229,10 @@ static struct clocksource clocksource_tod = { */ void __init time_init(void) { - u64 init_timer_cc; - - init_timer_cc = reset_tod_clock(); - jiffies_timer_cc = init_timer_cc - jiffies_64 * CLK_TICKS_PER_JIFFY; + sched_clock_base_cc = reset_tod_clock(); /* set xtime */ - tod_to_timeval(init_timer_cc - TOD_UNIX_EPOCH, &xtime); + tod_to_timeval(sched_clock_base_cc - TOD_UNIX_EPOCH, &xtime); set_normalized_timespec(&wall_to_monotonic, -xtime.tv_sec, -xtime.tv_nsec); @@ -289,7 +286,7 @@ static unsigned long long adjust_time(unsigned long long old, delta = -delta; adjust.offset = -ticks * (1000000 / HZ); } - jiffies_timer_cc += delta; + sched_clock_base_cc += delta; if (adjust.offset != 0) { printk(KERN_NOTICE "etr: time adjusted by %li micro-seconds\n", adjust.offset); -- cgit v1.1 From 2944a5c971c12766e2438ea407ec3567949c32b7 Mon Sep 17 00:00:00 2001 From: Christian Borntraeger Date: Thu, 27 Nov 2008 11:05:57 +0100 Subject: [S390] pgtable.h: Fix oops in unmap_vmas for KVM processes When running several kvm processes with lots of memory overcommitment, we have seen an oops during process shutdown: ------------[ cut here ]------------ Kernel BUG at 0000000000193434 [verbose debug info unavailable] addressing exception: 0005 [#1] PREEMPT SMP Modules linked in: kvm sunrpc qeth_l2 dm_mod qeth ccwgroup CPU: 10 Not tainted 2.6.28-rc4-kvm-bigiron-00521-g0ccca08-dirty #8 Process kuli (pid: 14460, task: 0000000149822338, ksp: 0000000024f57650) Krnl PSW : 0704e00180000000 0000000000193434 (unmap_vmas+0x884/0xf10) R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 EA:3 Krnl GPRS: 0000000000000002 0000000000000000 000000051008d000 000003e05e6034e0 00000000001933f6 00000000000001e9 0000000407259e0a 00000002be88c400 00000200001c1000 0000000407259608 0000000407259e08 0000000024f577f0 0000000407259e09 0000000000445fa8 00000000001933f6 0000000024f577f0 Krnl Code: 0000000000193426: eb22000c000d sllg %r2,%r2,12 000000000019342c: a7180000 lhi %r1,0 0000000000193430: b2290012 iske %r1,%r2 >0000000000193434: a7110002 tmll %r1,2 0000000000193438: a7840006 brc 8,193444 000000000019343c: 9602c000 oi 0(%r12),2 0000000000193440: 96806000 oi 0(%r6),128 0000000000193444: a7110004 tmll %r1,4 Call Trace: ([<00000000001933f6>] unmap_vmas+0x846/0xf10) [<0000000000199680>] exit_mmap+0x210/0x458 [<000000000012a8f8>] mmput+0x54/0xfc [<000000000012f714>] exit_mm+0x134/0x144 [<000000000013120c>] do_exit+0x240/0x878 [<00000000001318dc>] do_group_exit+0x98/0xc8 [<000000000013e6b0>] get_signal_to_deliver+0x30c/0x358 [<000000000010bee0>] do_signal+0xec/0x860 [<0000000000112e30>] sysc_sigpending+0xe/0x22 [<000002000013198a>] 0x2000013198a INFO: lockdep is turned off. Last Breaking-Event-Address: [<00000000001a68d0>] free_swap_and_cache+0x1a0/0x1a4 <4>---[ end trace bc19f1d51ac9db7c ]--- The faulting instruction is the storage key operation (iske) in ptep_rcp_copy (called by pte_clear, called by unmap_vmas). iske reads dirty and reference bit information for a physical page and requires a valid physical address. Since we are in pte_clear, we cannot rely on the pte containing a valid address. Fortunately we dont need these information in pte_clear - after all there is no mapping. The best fix is to remove the needless call to ptep_rcp_copy that contains the iske. Signed-off-by: Christian Borntraeger Signed-off-by: Martin Schwidefsky --- arch/s390/include/asm/pgtable.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch') diff --git a/arch/s390/include/asm/pgtable.h b/arch/s390/include/asm/pgtable.h index 7fc7613..5caddd4 100644 --- a/arch/s390/include/asm/pgtable.h +++ b/arch/s390/include/asm/pgtable.h @@ -679,8 +679,6 @@ static inline void pmd_clear(pmd_t *pmd) static inline void pte_clear(struct mm_struct *mm, unsigned long addr, pte_t *ptep) { - if (mm->context.has_pgste) - ptep_rcp_copy(ptep); pte_val(*ptep) = _PAGE_TYPE_EMPTY; if (mm->context.noexec) pte_val(ptep[PTRS_PER_PTE]) = _PAGE_TYPE_EMPTY; -- cgit v1.1 From 0778dc3a624b48cf80072b04405cacd1ad4079be Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Thu, 27 Nov 2008 11:05:58 +0100 Subject: [S390] Fix alignment of initial kernel stack. We need an alignment of 16384 bytes for the initial kernel stack if the kernel is configured for 16384 bytes stacks but the linker script currently guarantees only an alignment of 8192 bytes. So fix this and simply use THREAD_SIZE as alignment value which will always do the right thing. Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/init_task.c | 2 +- arch/s390/kernel/vmlinux.lds.S | 3 ++- 2 files changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/s390/kernel/init_task.c b/arch/s390/kernel/init_task.c index 7ad0039..e807168 100644 --- a/arch/s390/kernel/init_task.c +++ b/arch/s390/kernel/init_task.c @@ -26,7 +26,7 @@ EXPORT_SYMBOL(init_mm); /* * Initial thread structure. * - * We need to make sure that this is 8192-byte aligned due to the + * We need to make sure that this is THREAD_SIZE aligned due to the * way process stacks are handled. This is done by having a special * "init_task" linker map entry.. */ diff --git a/arch/s390/kernel/vmlinux.lds.S b/arch/s390/kernel/vmlinux.lds.S index 607bd67..d796d05 100644 --- a/arch/s390/kernel/vmlinux.lds.S +++ b/arch/s390/kernel/vmlinux.lds.S @@ -2,6 +2,7 @@ * Written by Martin Schwidefsky (schwidefsky@de.ibm.com) */ +#include #include #include @@ -86,7 +87,7 @@ SECTIONS } _edata = .; /* End of data section */ - . = ALIGN(2 * PAGE_SIZE); /* init_task */ + . = ALIGN(THREAD_SIZE); /* init_task */ .data.init_task : { *(.data.init_task) } -- cgit v1.1 From abd942194dcba2fa9d24d547b8acd4ef052eaf73 Mon Sep 17 00:00:00 2001 From: Martin Schwidefsky Date: Thu, 27 Nov 2008 11:05:59 +0100 Subject: [S390] Update default configuration. Signed-off-by: Martin Schwidefsky --- arch/s390/defconfig | 74 ++++++++++++++++++++++++++++++++++++----------------- 1 file changed, 51 insertions(+), 23 deletions(-) (limited to 'arch') diff --git a/arch/s390/defconfig b/arch/s390/defconfig index 9b0bc2c..a0e748d 100644 --- a/arch/s390/defconfig +++ b/arch/s390/defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc4 -# Thu Aug 21 19:43:29 2008 +# Linux kernel version: 2.6.28-rc6 +# Thu Nov 27 11:00:49 2008 # CONFIG_SCHED_MC=y CONFIG_MMU=y @@ -45,6 +45,7 @@ CONFIG_LOG_BUF_SHIFT=17 CONFIG_CGROUPS=y # CONFIG_CGROUP_DEBUG is not set CONFIG_CGROUP_NS=y +# CONFIG_CGROUP_FREEZER is not set # CONFIG_CGROUP_DEVICE is not set # CONFIG_CPUSETS is not set CONFIG_GROUP_SCHED=y @@ -84,6 +85,7 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set @@ -92,16 +94,10 @@ CONFIG_SLAB=y # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set CONFIG_KRETPROBES=y -# CONFIG_HAVE_IOREMAP_PROT is not set CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y +CONFIG_HAVE_ARCH_TRACEHOOK=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -135,6 +131,7 @@ CONFIG_DEFAULT_DEADLINE=y CONFIG_DEFAULT_IOSCHED="deadline" CONFIG_PREEMPT_NOTIFIERS=y CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Base setup @@ -189,7 +186,6 @@ CONFIG_SELECT_MEMORY_MODEL=y CONFIG_SPARSEMEM_MANUAL=y CONFIG_SPARSEMEM=y CONFIG_HAVE_MEMORY_PRESENT=y -# CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPARSEMEM_EXTREME=y CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y CONFIG_SPARSEMEM_VMEMMAP=y @@ -200,9 +196,11 @@ CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_MIGRATION=y CONFIG_RESOURCES_64BIT=y +CONFIG_PHYS_ADDR_T_64BIT=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # I/O subsystem configuration @@ -220,6 +218,8 @@ CONFIG_IPL=y CONFIG_IPL_VM=y CONFIG_BINFMT_ELF=y CONFIG_COMPAT_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m CONFIG_FORCE_MAX_ZONEORDER=9 # CONFIG_PROCESS_DEBUG is not set @@ -255,7 +255,7 @@ CONFIG_XFRM=y # CONFIG_XFRM_STATISTICS is not set CONFIG_NET_KEY=y # CONFIG_NET_KEY_MIGRATE is not set -CONFIG_IUCV=m +CONFIG_IUCV=y CONFIG_AFIUCV=m CONFIG_INET=y CONFIG_IP_MULTICAST=y @@ -282,7 +282,6 @@ CONFIG_INET_TCP_DIAG=y CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=y # CONFIG_IPV6_PRIVACY is not set # CONFIG_IPV6_ROUTER_PREF is not set @@ -331,10 +330,12 @@ CONFIG_NF_CONNTRACK=m # CONFIG_NF_CONNTRACK_TFTP is not set # CONFIG_NF_CT_NETLINK is not set # CONFIG_NETFILTER_XTABLES is not set +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +# CONFIG_NF_DEFRAG_IPV4 is not set # CONFIG_NF_CONNTRACK_IPV4 is not set # CONFIG_IP_NF_QUEUE is not set # CONFIG_IP_NF_IPTABLES is not set @@ -374,6 +375,7 @@ CONFIG_NET_SCH_CBQ=m # CONFIG_NET_SCH_HTB is not set # CONFIG_NET_SCH_HFSC is not set CONFIG_NET_SCH_PRIO=m +CONFIG_NET_SCH_MULTIQ=y CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m @@ -406,6 +408,7 @@ CONFIG_NET_ACT_POLICE=y CONFIG_NET_ACT_NAT=m # CONFIG_NET_ACT_PEDIT is not set # CONFIG_NET_ACT_SIMP is not set +# CONFIG_NET_ACT_SKBEDIT is not set # CONFIG_NET_CLS_IND is not set CONFIG_NET_SCH_FIFO=y @@ -424,6 +427,7 @@ CONFIG_CAN_BCM=m CONFIG_CAN_VCAN=m # CONFIG_CAN_DEBUG_DEVICES is not set # CONFIG_AF_RXRPC is not set +# CONFIG_PHONET is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set # CONFIG_PCMCIA is not set @@ -473,7 +477,7 @@ CONFIG_VIRTIO_BLK=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set -# CONFIG_HAVE_IDE is not set +# CONFIG_C2PORT is not set # # SCSI device support @@ -525,6 +529,7 @@ CONFIG_SCSI_DH_EMC=m CONFIG_SCSI_DH_ALUA=m CONFIG_MD=y CONFIG_BLK_DEV_MD=y +CONFIG_MD_AUTODETECT=y CONFIG_MD_LINEAR=m CONFIG_MD_RAID0=m CONFIG_MD_RAID1=m @@ -555,6 +560,9 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y # CONFIG_TR is not set @@ -632,13 +640,12 @@ CONFIG_S390_VMUR=m # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set - -# -# Sonics Silicon Backplane -# +# CONFIG_REGULATOR is not set # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set CONFIG_ACCESSIBILITY=y +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -650,13 +657,14 @@ CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set @@ -688,6 +696,7 @@ CONFIG_GENERIC_ACL=y CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y @@ -728,6 +737,7 @@ CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y +# CONFIG_SUNRPC_REGISTER_V4 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -800,12 +810,24 @@ CONFIG_DEBUG_MEMORY_INIT=y # CONFIG_DEBUG_SG is not set # CONFIG_FRAME_POINTER is not set # CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_KPROBES_SANITY_TEST is not set # CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set # CONFIG_LKDTM is not set # CONFIG_FAULT_INJECTION is not set # CONFIG_LATENCYTOP is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_PREEMPT_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set CONFIG_SAMPLES=y # CONFIG_SAMPLE_KOBJECT is not set # CONFIG_SAMPLE_KPROBES is not set @@ -816,16 +838,19 @@ CONFIG_SAMPLES=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # +CONFIG_CRYPTO_FIPS=y CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y -CONFIG_CRYPTO_HASH=m +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m # CONFIG_CRYPTO_NULL is not set @@ -877,7 +902,7 @@ CONFIG_CRYPTO_SHA1=m # # Ciphers # -# CONFIG_CRYPTO_AES is not set +CONFIG_CRYPTO_AES=m # CONFIG_CRYPTO_ANUBIS is not set # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_BLOWFISH is not set @@ -898,6 +923,11 @@ CONFIG_CRYPTO_SEED=m # # CONFIG_CRYPTO_DEFLATE is not set CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +CONFIG_CRYPTO_ANSI_CPRNG=m CONFIG_CRYPTO_HW=y CONFIG_ZCRYPT=m # CONFIG_ZCRYPT_MONOLITHIC is not set @@ -912,8 +942,6 @@ CONFIG_S390_PRNG=m # Library routines # CONFIG_BITREVERSE=m -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set CONFIG_CRC_T10DIF=y -- cgit v1.1 From b627c8b17ccacba38c975bc0f69a49fc4e5261c9 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Thu, 20 Nov 2008 20:49:56 +0100 Subject: x86: always define DECLARE_PCI_UNMAP* macros Impact: fix boot crash on AMD IOMMU if CONFIG_GART_IOMMU is off Currently these macros evaluate to a no-op except the kernel is compiled with GART or Calgary support. But we also need these macros when we have SWIOTLB, VT-d or AMD IOMMU in the kernel. Since we always compile at least with SWIOTLB we can define these macros always. This patch is also for stable backport for the same reason the SWIOTLB default selection patch is. Signed-off-by: Joerg Roedel Cc: Signed-off-by: Ingo Molnar --- arch/x86/include/asm/pci_64.h | 14 -------------- 1 file changed, 14 deletions(-) (limited to 'arch') diff --git a/arch/x86/include/asm/pci_64.h b/arch/x86/include/asm/pci_64.h index 5b28995..d02d936 100644 --- a/arch/x86/include/asm/pci_64.h +++ b/arch/x86/include/asm/pci_64.h @@ -34,8 +34,6 @@ extern void pci_iommu_alloc(void); */ #define PCI_DMA_BUS_IS_PHYS (dma_ops->is_phys) -#if defined(CONFIG_GART_IOMMU) || defined(CONFIG_CALGARY_IOMMU) - #define DECLARE_PCI_UNMAP_ADDR(ADDR_NAME) \ dma_addr_t ADDR_NAME; #define DECLARE_PCI_UNMAP_LEN(LEN_NAME) \ @@ -49,18 +47,6 @@ extern void pci_iommu_alloc(void); #define pci_unmap_len_set(PTR, LEN_NAME, VAL) \ (((PTR)->LEN_NAME) = (VAL)) -#else -/* No IOMMU */ - -#define DECLARE_PCI_UNMAP_ADDR(ADDR_NAME) -#define DECLARE_PCI_UNMAP_LEN(LEN_NAME) -#define pci_unmap_addr(PTR, ADDR_NAME) (0) -#define pci_unmap_addr_set(PTR, ADDR_NAME, VAL) do { } while (0) -#define pci_unmap_len(PTR, LEN_NAME) (0) -#define pci_unmap_len_set(PTR, LEN_NAME, VAL) do { } while (0) - -#endif - #endif /* __KERNEL__ */ #endif /* _ASM_X86_PCI_64_H */ -- cgit v1.1 From a730b327ca70f0e4d933202e3979e96613c3585f Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 20 Nov 2008 17:34:57 +0100 Subject: [ARM] pxa/palmtx: misc fixes to use generic GPIO API Signed-off-by: Marek Vasut Signed-off-by: Eric Miao --- arch/arm/mach-pxa/palmtx.c | 150 +++++++++++++++++++++++++++++++++++---------- 1 file changed, 118 insertions(+), 32 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c index 4447711..a9d94f5 100644 --- a/arch/arm/mach-pxa/palmtx.c +++ b/arch/arm/mach-pxa/palmtx.c @@ -56,6 +56,9 @@ static unsigned long palmtx_pin_config[] __initdata = { GPIO110_MMC_DAT_2, GPIO111_MMC_DAT_3, GPIO112_MMC_CMD, + GPIO14_GPIO, /* SD detect */ + GPIO114_GPIO, /* SD power */ + GPIO115_GPIO, /* SD r/o switch */ /* AC97 */ GPIO28_AC97_BITCLK, @@ -64,6 +67,7 @@ static unsigned long palmtx_pin_config[] __initdata = { GPIO31_AC97_SYNC, /* IrDA */ + GPIO40_GPIO, /* ir disable */ GPIO46_FICP_RXD, GPIO47_FICP_TXD, @@ -71,7 +75,8 @@ static unsigned long palmtx_pin_config[] __initdata = { GPIO16_PWM0_OUT, /* USB */ - GPIO13_GPIO, + GPIO13_GPIO, /* usb detect */ + GPIO95_GPIO, /* usb power */ /* PCMCIA */ GPIO48_nPOE, @@ -84,6 +89,45 @@ static unsigned long palmtx_pin_config[] __initdata = { GPIO55_nPREG, GPIO56_nPWAIT, GPIO57_nIOIS16, + GPIO94_GPIO, /* wifi power 1 */ + GPIO108_GPIO, /* wifi power 2 */ + GPIO116_GPIO, /* wifi ready */ + + /* MATRIX KEYPAD */ + GPIO100_KP_MKIN_0, + GPIO101_KP_MKIN_1, + GPIO102_KP_MKIN_2, + GPIO97_KP_MKIN_3, + GPIO103_KP_MKOUT_0, + GPIO104_KP_MKOUT_1, + GPIO105_KP_MKOUT_2, + + /* LCD */ + GPIO58_LCD_LDD_0, + GPIO59_LCD_LDD_1, + GPIO60_LCD_LDD_2, + GPIO61_LCD_LDD_3, + GPIO62_LCD_LDD_4, + GPIO63_LCD_LDD_5, + GPIO64_LCD_LDD_6, + GPIO65_LCD_LDD_7, + GPIO66_LCD_LDD_8, + GPIO67_LCD_LDD_9, + GPIO68_LCD_LDD_10, + GPIO69_LCD_LDD_11, + GPIO70_LCD_LDD_12, + GPIO71_LCD_LDD_13, + GPIO72_LCD_LDD_14, + GPIO73_LCD_LDD_15, + GPIO74_LCD_FCLK, + GPIO75_LCD_LCLK, + GPIO76_LCD_PCLK, + GPIO77_LCD_BIAS, + + /* MISC. */ + GPIO10_GPIO, /* hotsync button */ + GPIO12_GPIO, /* power detect */ + GPIO107_GPIO, /* earphone detect */ }; /****************************************************************************** @@ -95,32 +139,49 @@ static int palmtx_mci_init(struct device *dev, irq_handler_t palmtx_detect_int, int err = 0; /* Setup an interrupt for detecting card insert/remove events */ - err = request_irq(IRQ_GPIO_PALMTX_SD_DETECT_N, palmtx_detect_int, - IRQF_DISABLED | IRQF_SAMPLE_RANDOM | + err = gpio_request(GPIO_NR_PALMTX_SD_DETECT_N, "SD IRQ"); + if (err) + goto err; + err = gpio_direction_input(GPIO_NR_PALMTX_SD_DETECT_N); + if (err) + goto err2; + err = request_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N), + palmtx_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM | IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, "SD/MMC card detect", data); if (err) { printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n", __func__); - return err; + goto err2; } err = gpio_request(GPIO_NR_PALMTX_SD_POWER, "SD_POWER"); if (err) - goto pwr_err; + goto err3; + err = gpio_direction_output(GPIO_NR_PALMTX_SD_POWER, 0); + if (err) + goto err4; err = gpio_request(GPIO_NR_PALMTX_SD_READONLY, "SD_READONLY"); if (err) - goto ro_err; + goto err4; + err = gpio_direction_input(GPIO_NR_PALMTX_SD_READONLY); + if (err) + goto err5; printk(KERN_DEBUG "%s: irq registered\n", __func__); return 0; -ro_err: +err5: + gpio_free(GPIO_NR_PALMTX_SD_READONLY); +err4: gpio_free(GPIO_NR_PALMTX_SD_POWER); -pwr_err: - free_irq(IRQ_GPIO_PALMTX_SD_DETECT_N, data); +err3: + free_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N), data); +err2: + gpio_free(GPIO_NR_PALMTX_SD_DETECT_N); +err: return err; } @@ -128,7 +189,8 @@ static void palmtx_mci_exit(struct device *dev, void *data) { gpio_free(GPIO_NR_PALMTX_SD_READONLY); gpio_free(GPIO_NR_PALMTX_SD_POWER); - free_irq(IRQ_GPIO_PALMTX_SD_DETECT_N, data); + free_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N), data); + gpio_free(GPIO_NR_PALMTX_SD_DETECT_N); } static void palmtx_mci_power(struct device *dev, unsigned int vdd) @@ -167,7 +229,6 @@ static unsigned int palmtx_matrix_keys[] = { KEY(3, 0, KEY_RIGHT), KEY(3, 2, KEY_LEFT), - }; static struct pxa27x_keypad_platform_data palmtx_keypad_platform_data = { @@ -209,11 +270,19 @@ static int palmtx_backlight_init(struct device *dev) ret = gpio_request(GPIO_NR_PALMTX_BL_POWER, "BL POWER"); if (ret) goto err; + ret = gpio_direction_output(GPIO_NR_PALMTX_BL_POWER, 0); + if (ret) + goto err2; ret = gpio_request(GPIO_NR_PALMTX_LCD_POWER, "LCD POWER"); if (ret) goto err2; + ret = gpio_direction_output(GPIO_NR_PALMTX_LCD_POWER, 0); + if (ret) + goto err3; return 0; +err3: + gpio_free(GPIO_NR_PALMTX_LCD_POWER); err2: gpio_free(GPIO_NR_PALMTX_BL_POWER); err: @@ -254,6 +323,24 @@ static struct platform_device palmtx_backlight = { /****************************************************************************** * IrDA ******************************************************************************/ +static int palmtx_irda_startup(struct device *dev) +{ + int err; + err = gpio_request(GPIO_NR_PALMTX_IR_DISABLE, "IR DISABLE"); + if (err) + goto err; + err = gpio_direction_output(GPIO_NR_PALMTX_IR_DISABLE, 1); + if (err) + gpio_free(GPIO_NR_PALMTX_IR_DISABLE); +err: + return err; +} + +static void palmtx_irda_shutdown(struct device *dev) +{ + gpio_free(GPIO_NR_PALMTX_IR_DISABLE); +} + static void palmtx_irda_transceiver_mode(struct device *dev, int mode) { gpio_set_value(GPIO_NR_PALMTX_IR_DISABLE, mode & IR_OFF); @@ -261,6 +348,8 @@ static void palmtx_irda_transceiver_mode(struct device *dev, int mode) } static struct pxaficp_platform_data palmtx_ficp_platform_data = { + .startup = palmtx_irda_startup, + .shutdown = palmtx_irda_shutdown, .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF, .transceiver_mode = palmtx_irda_transceiver_mode, }; @@ -268,17 +357,11 @@ static struct pxaficp_platform_data palmtx_ficp_platform_data = { /****************************************************************************** * UDC ******************************************************************************/ -static void palmtx_udc_command(int cmd) -{ - gpio_set_value(GPIO_NR_PALMTX_USB_POWER, !cmd); - udelay(50); - gpio_set_value(GPIO_NR_PALMTX_USB_PULLUP, !cmd); -} - static struct pxa2xx_udc_mach_info palmtx_udc_info __initdata = { .gpio_vbus = GPIO_NR_PALMTX_USB_DETECT_N, .gpio_vbus_inverted = 1, - .udc_command = palmtx_udc_command, + .gpio_pullup = GPIO_NR_PALMTX_USB_POWER, + .gpio_pullup_inverted = 0, }; /****************************************************************************** @@ -290,17 +373,16 @@ static int power_supply_init(struct device *dev) ret = gpio_request(GPIO_NR_PALMTX_POWER_DETECT, "CABLE_STATE_AC"); if (ret) - goto err_cs_ac; - - ret = gpio_request(GPIO_NR_PALMTX_USB_DETECT_N, "CABLE_STATE_USB"); + goto err1; + ret = gpio_direction_input(GPIO_NR_PALMTX_POWER_DETECT); if (ret) - goto err_cs_usb; + goto err2; return 0; -err_cs_usb: +err2: gpio_free(GPIO_NR_PALMTX_POWER_DETECT); -err_cs_ac: +err1: return ret; } @@ -309,14 +391,8 @@ static int palmtx_is_ac_online(void) return gpio_get_value(GPIO_NR_PALMTX_POWER_DETECT); } -static int palmtx_is_usb_online(void) -{ - return !gpio_get_value(GPIO_NR_PALMTX_USB_DETECT_N); -} - static void power_supply_exit(struct device *dev) { - gpio_free(GPIO_NR_PALMTX_USB_DETECT_N); gpio_free(GPIO_NR_PALMTX_POWER_DETECT); } @@ -327,7 +403,6 @@ static char *palmtx_supplicants[] = { static struct pda_power_pdata power_supply_info = { .init = power_supply_init, .is_ac_online = palmtx_is_ac_online, - .is_usb_online = palmtx_is_usb_online, .exit = power_supply_exit, .supplied_to = palmtx_supplicants, .num_supplicants = ARRAY_SIZE(palmtx_supplicants), @@ -410,12 +485,23 @@ static void __init palmtx_map_io(void) iotable_init(palmtx_io_desc, ARRAY_SIZE(palmtx_io_desc)); } +/* setup udc GPIOs initial state */ +static void __init palmtx_udc_init(void) +{ + if (!gpio_request(GPIO_NR_PALMTX_USB_POWER, "UDC Vbus")) { + gpio_direction_output(GPIO_NR_PALMTX_USB_POWER, 1); + gpio_free(GPIO_NR_PALMTX_USB_POWER); + } +} + + static void __init palmtx_init(void) { pxa2xx_mfp_config(ARRAY_AND_SIZE(palmtx_pin_config)); set_pxa_fb_info(&palmtx_lcd_screen); pxa_set_mci_info(&palmtx_mci_platform_data); + palmtx_udc_init(); pxa_set_udc_info(&palmtx_udc_info); pxa_set_ac97_info(NULL); pxa_set_ficp_info(&palmtx_ficp_platform_data); -- cgit v1.1 From 7b1dedca42ac0d0d0be01e39d8461bb53a2389b3 Mon Sep 17 00:00:00 2001 From: Thomas Bogendoerfer Date: Sat, 29 Nov 2008 13:46:27 +0100 Subject: x86: fix dma_mapping_error for 32bit x86 Devices like b44 ethernet can't dma from addresses above 1GB. The driver handles this cases by falling back to GFP_DMA allocation. But for detecting the problem it needs to get an indication from dma_mapping_error. The bug is triggered by using a VMSPLIT option of 2G/2G. Signed-off-by: Thomas Bogendoerfer Acked-by: FUJITA Tomonori Signed-off-by: Ingo Molnar --- arch/x86/include/asm/dma-mapping.h | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/x86/include/asm/dma-mapping.h b/arch/x86/include/asm/dma-mapping.h index 7f225a4..097794f 100644 --- a/arch/x86/include/asm/dma-mapping.h +++ b/arch/x86/include/asm/dma-mapping.h @@ -71,15 +71,13 @@ static inline struct dma_mapping_ops *get_dma_ops(struct device *dev) /* Make sure we keep the same behaviour */ static inline int dma_mapping_error(struct device *dev, dma_addr_t dma_addr) { -#ifdef CONFIG_X86_32 - return 0; -#else +#ifdef CONFIG_X86_64 struct dma_mapping_ops *ops = get_dma_ops(dev); if (ops->mapping_error) return ops->mapping_error(dev, dma_addr); - return (dma_addr == bad_dma_address); #endif + return (dma_addr == bad_dma_address); } #define dma_alloc_noncoherent(d, s, h, f) dma_alloc_coherent(d, s, h, f) -- cgit v1.1 From 7d6a8a1c487422b772201927c454930377d8cf7e Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:33:34 +0000 Subject: false __cpuinit positives on alpha pure noise - alpha doesn't have CPU hotplug Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/alpha/kernel/smp.c | 6 +++--- arch/alpha/kernel/traps.c | 4 ++-- 2 files changed, 5 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/alpha/kernel/smp.c b/arch/alpha/kernel/smp.c index e657c45..cf7da10 100644 --- a/arch/alpha/kernel/smp.c +++ b/arch/alpha/kernel/smp.c @@ -121,7 +121,7 @@ wait_boot_cpu_to_stop(int cpuid) /* * Where secondaries begin a life of C. */ -void __init +void __cpuinit smp_callin(void) { int cpuid = hard_smp_processor_id(); @@ -198,7 +198,7 @@ wait_for_txrdy (unsigned long cpumask) * Send a message to a secondary's console. "START" is one such * interesting message. ;-) */ -static void __init +static void __cpuinit send_secondary_console_msg(char *str, int cpuid) { struct percpu_struct *cpu; @@ -289,7 +289,7 @@ recv_secondary_console_msg(void) /* * Convince the console to have a secondary cpu begin execution. */ -static int __init +static int __cpuinit secondary_cpu_start(int cpuid, struct task_struct *idle) { struct percpu_struct *cpu; diff --git a/arch/alpha/kernel/traps.c b/arch/alpha/kernel/traps.c index c778779..cefc5a3 100644 --- a/arch/alpha/kernel/traps.c +++ b/arch/alpha/kernel/traps.c @@ -31,7 +31,7 @@ static int opDEC_fix; -static void __init +static void __cpuinit opDEC_check(void) { __asm__ __volatile__ ( @@ -1072,7 +1072,7 @@ give_sigbus: return; } -void __init +void __cpuinit trap_init(void) { /* Tell PAL-code what global pointer we want in the kernel. */ -- cgit v1.1 From 4ea8fb9c1cc67bee980dca589ec8d0d4e62858c7 Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:33:44 +0000 Subject: powerpc set_huge_psize() false positive called only from __init, calls __init. Incidentally, it ought to be static in file. Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/powerpc/include/asm/mmu-hash64.h | 1 - arch/powerpc/mm/hugetlbpage.c | 2 +- 2 files changed, 1 insertion(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/include/asm/mmu-hash64.h b/arch/powerpc/include/asm/mmu-hash64.h index 5a44174..68b7526 100644 --- a/arch/powerpc/include/asm/mmu-hash64.h +++ b/arch/powerpc/include/asm/mmu-hash64.h @@ -280,7 +280,6 @@ extern int hash_huge_page(struct mm_struct *mm, unsigned long access, extern int htab_bolt_mapping(unsigned long vstart, unsigned long vend, unsigned long pstart, unsigned long prot, int psize, int ssize); -extern void set_huge_psize(int psize); extern void add_gpage(unsigned long addr, unsigned long page_size, unsigned long number_of_pages); extern void demote_segment_4k(struct mm_struct *mm, unsigned long addr); diff --git a/arch/powerpc/mm/hugetlbpage.c b/arch/powerpc/mm/hugetlbpage.c index a117024..7bbf4e4 100644 --- a/arch/powerpc/mm/hugetlbpage.c +++ b/arch/powerpc/mm/hugetlbpage.c @@ -677,7 +677,7 @@ repeat: return err; } -void set_huge_psize(int psize) +static void __init set_huge_psize(int psize) { /* Check that it is a page size supported by the hardware and * that it fits within pagetable limits. */ -- cgit v1.1 From 409832f5484cd1e2d8812c3236dffb33d01c359b Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:33:54 +0000 Subject: sparc32 cpuinit flase positives All noise since we don't have CPU hotplug there. However, they did expose something very odd-looking in there - poke_viking() does a bunch of identical btfixup each time it's called (i.e. for each CPU). That one is left alone for now; just the trivial misannotation fixes. Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/sparc/kernel/cpu.c | 2 +- arch/sparc/kernel/smp.c | 4 ++-- arch/sparc/kernel/sun4d_smp.c | 4 ++-- arch/sparc/kernel/sun4m_smp.c | 2 +- arch/sparc/kernel/trampoline.S | 4 ++-- arch/sparc/mm/srmmu.c | 14 +++++++------- 6 files changed, 15 insertions(+), 15 deletions(-) (limited to 'arch') diff --git a/arch/sparc/kernel/cpu.c b/arch/sparc/kernel/cpu.c index e7a0edf..1fc17f5 100644 --- a/arch/sparc/kernel/cpu.c +++ b/arch/sparc/kernel/cpu.c @@ -126,7 +126,7 @@ char *sparc_fpu_type; unsigned int fsr_storage; -void __init cpu_probe(void) +void __cpuinit cpu_probe(void) { int psr_impl, psr_vers, fpu_vers; int i, psr; diff --git a/arch/sparc/kernel/smp.c b/arch/sparc/kernel/smp.c index 1619ec1..e396c1f 100644 --- a/arch/sparc/kernel/smp.c +++ b/arch/sparc/kernel/smp.c @@ -35,7 +35,7 @@ #include "irq.h" -volatile unsigned long cpu_callin_map[NR_CPUS] __initdata = {0,}; +volatile unsigned long cpu_callin_map[NR_CPUS] __cpuinitdata = {0,}; unsigned char boot_cpu_id = 0; unsigned char boot_cpu_id4 = 0; /* boot_cpu_id << 2 */ @@ -120,7 +120,7 @@ void cpu_panic(void) panic("SMP bolixed\n"); } -struct linux_prom_registers smp_penguin_ctable __initdata = { 0 }; +struct linux_prom_registers smp_penguin_ctable __cpuinitdata = { 0 }; void smp_send_reschedule(int cpu) { diff --git a/arch/sparc/kernel/sun4d_smp.c b/arch/sparc/kernel/sun4d_smp.c index 7a6a5e7..16ab0cb 100644 --- a/arch/sparc/kernel/sun4d_smp.c +++ b/arch/sparc/kernel/sun4d_smp.c @@ -83,7 +83,7 @@ static inline void show_leds(int cpuid) "i" (ASI_M_CTL)); } -void __init smp4d_callin(void) +void __cpuinit smp4d_callin(void) { int cpuid = hard_smp4d_processor_id(); extern spinlock_t sun4d_imsk_lock; @@ -386,7 +386,7 @@ void smp4d_percpu_timer_interrupt(struct pt_regs *regs) extern unsigned int lvl14_resolution; -static void __init smp_setup_percpu_timer(void) +static void __cpuinit smp_setup_percpu_timer(void) { int cpu = hard_smp4d_processor_id(); diff --git a/arch/sparc/kernel/sun4m_smp.c b/arch/sparc/kernel/sun4m_smp.c index 5fc386d..4f8d605 100644 --- a/arch/sparc/kernel/sun4m_smp.c +++ b/arch/sparc/kernel/sun4m_smp.c @@ -343,7 +343,7 @@ void smp4m_percpu_timer_interrupt(struct pt_regs *regs) extern unsigned int lvl14_resolution; -static void __init smp_setup_percpu_timer(void) +static void __cpuinit smp_setup_percpu_timer(void) { int cpu = smp_processor_id(); diff --git a/arch/sparc/kernel/trampoline.S b/arch/sparc/kernel/trampoline.S index 356c56a..5e235c5 100644 --- a/arch/sparc/kernel/trampoline.S +++ b/arch/sparc/kernel/trampoline.S @@ -18,7 +18,7 @@ .globl sun4m_cpu_startup, __smp4m_processor_id .globl sun4d_cpu_startup, __smp4d_processor_id - __INIT + __CPUINIT .align 4 /* When we start up a cpu for the first time it enters this routine. @@ -109,7 +109,7 @@ __smp4d_processor_id: /* CPUID in bootbus can be found at PA 0xff0140000 */ #define SUN4D_BOOTBUS_CPUID 0xf0140000 - __INIT + __CPUINIT .align 4 sun4d_cpu_startup: diff --git a/arch/sparc/mm/srmmu.c b/arch/sparc/mm/srmmu.c index 6a5d7ca..dd8aa36 100644 --- a/arch/sparc/mm/srmmu.c +++ b/arch/sparc/mm/srmmu.c @@ -1251,7 +1251,7 @@ static inline void map_kernel(void) /* Paging initialization on the Sparc Reference MMU. */ extern void sparc_context_init(int); -void (*poke_srmmu)(void) __initdata = NULL; +void (*poke_srmmu)(void) __cpuinitdata = NULL; extern unsigned long bootmem_init(unsigned long *pages_avail); @@ -1446,7 +1446,7 @@ static void __init init_vac_layout(void) (int)vac_cache_size, (int)vac_line_size); } -static void __init poke_hypersparc(void) +static void __cpuinit poke_hypersparc(void) { volatile unsigned long clear; unsigned long mreg = srmmu_get_mmureg(); @@ -1501,7 +1501,7 @@ static void __init init_hypersparc(void) hypersparc_setup_blockops(); } -static void __init poke_cypress(void) +static void __cpuinit poke_cypress(void) { unsigned long mreg = srmmu_get_mmureg(); unsigned long faddr, tagval; @@ -1589,7 +1589,7 @@ static void __init init_cypress_605(unsigned long mrev) init_cypress_common(); } -static void __init poke_swift(void) +static void __cpuinit poke_swift(void) { unsigned long mreg; @@ -1771,7 +1771,7 @@ static void turbosparc_flush_tlb_page(struct vm_area_struct *vma, unsigned long } -static void __init poke_turbosparc(void) +static void __cpuinit poke_turbosparc(void) { unsigned long mreg = srmmu_get_mmureg(); unsigned long ccreg; @@ -1834,7 +1834,7 @@ static void __init init_turbosparc(void) poke_srmmu = poke_turbosparc; } -static void __init poke_tsunami(void) +static void __cpuinit poke_tsunami(void) { unsigned long mreg = srmmu_get_mmureg(); @@ -1876,7 +1876,7 @@ static void __init init_tsunami(void) tsunami_setup_blockops(); } -static void __init poke_viking(void) +static void __cpuinit poke_viking(void) { unsigned long mreg = srmmu_get_mmureg(); static int smp_catch; -- cgit v1.1 From 8c29890aef80702824e2284909ee301ef2430a3e Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:34:04 +0000 Subject: sparc64 trivial section misannotations Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/sparc64/kernel/smp.c | 4 ++-- arch/sparc64/mm/init.c | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/sparc64/kernel/smp.c b/arch/sparc64/kernel/smp.c index e562711..f500b06 100644 --- a/arch/sparc64/kernel/smp.c +++ b/arch/sparc64/kernel/smp.c @@ -282,7 +282,7 @@ static unsigned long kimage_addr_to_ra(void *p) return kern_base + (val - KERNBASE); } -static void ldom_startcpu_cpuid(unsigned int cpu, unsigned long thread_reg) +static void __cpuinit ldom_startcpu_cpuid(unsigned int cpu, unsigned long thread_reg) { extern unsigned long sparc64_ttable_tl0; extern unsigned long kern_locked_tte_data; @@ -343,7 +343,7 @@ extern unsigned long sparc64_cpu_startup; */ static struct thread_info *cpu_new_thread = NULL; -static int __devinit smp_boot_one_cpu(unsigned int cpu) +static int __cpuinit smp_boot_one_cpu(unsigned int cpu) { struct trap_per_cpu *tb = &trap_block[cpu]; unsigned long entry = diff --git a/arch/sparc64/mm/init.c b/arch/sparc64/mm/init.c index 3c10daf..185f346 100644 --- a/arch/sparc64/mm/init.c +++ b/arch/sparc64/mm/init.c @@ -956,7 +956,7 @@ int of_node_to_nid(struct device_node *dp) return nid; } -static void add_node_ranges(void) +static void __init add_node_ranges(void) { int i; -- cgit v1.1 From e669dae6141ff97d3c7566207f5de3b487dcf837 Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:35:04 +0000 Subject: of_platform_driver noise on sparce switch to __init for those; unlike powerpc sparc has no hotplug support for that stuff and their ->probe() tends to call __init functions while being declared __devinit. Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/sparc64/kernel/pci_fire.c | 2 +- arch/sparc64/kernel/pci_psycho.c | 4 ++-- arch/sparc64/kernel/pci_sun4v.c | 2 +- 3 files changed, 4 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/sparc64/kernel/pci_fire.c b/arch/sparc64/kernel/pci_fire.c index 9462b68..fcbbac6 100644 --- a/arch/sparc64/kernel/pci_fire.c +++ b/arch/sparc64/kernel/pci_fire.c @@ -455,7 +455,7 @@ static int __init pci_fire_pbm_init(struct pci_pbm_info *pbm, return 0; } -static int __devinit fire_probe(struct of_device *op, +static int __init fire_probe(struct of_device *op, const struct of_device_id *match) { struct device_node *dp = op->node; diff --git a/arch/sparc64/kernel/pci_psycho.c b/arch/sparc64/kernel/pci_psycho.c index dfb3ec8..56605ad 100644 --- a/arch/sparc64/kernel/pci_psycho.c +++ b/arch/sparc64/kernel/pci_psycho.c @@ -493,7 +493,7 @@ static void __init psycho_pbm_init(struct pci_pbm_info *pbm, psycho_scan_bus(pbm, &op->dev); } -static struct pci_pbm_info * __devinit psycho_find_sibling(u32 upa_portid) +static struct pci_pbm_info * __init psycho_find_sibling(u32 upa_portid) { struct pci_pbm_info *pbm; @@ -506,7 +506,7 @@ static struct pci_pbm_info * __devinit psycho_find_sibling(u32 upa_portid) #define PSYCHO_CONFIGSPACE 0x001000000UL -static int __devinit psycho_probe(struct of_device *op, +static int __init psycho_probe(struct of_device *op, const struct of_device_id *match) { const struct linux_prom64_registers *pr_regs; diff --git a/arch/sparc64/kernel/pci_sun4v.c b/arch/sparc64/kernel/pci_sun4v.c index 34a1fde..4b27b0e 100644 --- a/arch/sparc64/kernel/pci_sun4v.c +++ b/arch/sparc64/kernel/pci_sun4v.c @@ -929,7 +929,7 @@ static int __init pci_sun4v_pbm_init(struct pci_pbm_info *pbm, return 0; } -static int __devinit pci_sun4v_probe(struct of_device *op, +static int __init pci_sun4v_probe(struct of_device *op, const struct of_device_id *match) { const struct linux_prom64_registers *regs; -- cgit v1.1 From 1c4567aeed84a2746d78d4c1fe092222a559d43f Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:35:54 +0000 Subject: m32r: section noise in head.S usual "introduce .text.head, put it in front of TEXT_TEXT in vmlinux.lds.S, make the stuff up to jump to start_kernel live in it", same as on other targets. Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/m32r/kernel/head.S | 4 ++-- arch/m32r/kernel/vmlinux.lds.S | 1 + 2 files changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/m32r/kernel/head.S b/arch/m32r/kernel/head.S index 4018077..9091606 100644 --- a/arch/m32r/kernel/head.S +++ b/arch/m32r/kernel/head.S @@ -23,7 +23,7 @@ __INITDATA /* * References to members of the boot_cpu_data structure. */ - .text +.section .text.head, "ax" .global start_kernel .global __bss_start .global _end @@ -133,7 +133,6 @@ loop1: /* * AP startup routine */ - .text .global eit_vector ENTRY(startup_AP) ;; setup EVB @@ -230,6 +229,7 @@ ENTRY(startup_AP) nop #endif /* CONFIG_SMP */ + .text ENTRY(stack_start) .long init_thread_union+8192 .long __KERNEL_DS diff --git a/arch/m32r/kernel/vmlinux.lds.S b/arch/m32r/kernel/vmlinux.lds.S index 15a6f36..9db05df 100644 --- a/arch/m32r/kernel/vmlinux.lds.S +++ b/arch/m32r/kernel/vmlinux.lds.S @@ -27,6 +27,7 @@ SECTIONS _text = .; /* Text and read-only data */ .boot : { *(.boot) } = 0 .text : { + *(.text.head) TEXT_TEXT SCHED_TEXT LOCK_TEXT -- cgit v1.1 From 5bac287ea51bb8678c3875d87a536071ef0fd590 Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:36:04 +0000 Subject: fix the section noise in sparc head.S usual .text.head trick Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/sparc/kernel/head.S | 2 +- arch/sparc/kernel/vmlinux.lds.S | 1 + 2 files changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/sparc/kernel/head.S b/arch/sparc/kernel/head.S index 2d325fd..51b4042 100644 --- a/arch/sparc/kernel/head.S +++ b/arch/sparc/kernel/head.S @@ -72,7 +72,7 @@ sun4e_notsup: .align 4 /* The Sparc trap table, bootloader gives us control at _start. */ - .text + .section .text.head,"ax" .globl start, _stext, _start, __stext .globl trapbase _start: /* danger danger */ diff --git a/arch/sparc/kernel/vmlinux.lds.S b/arch/sparc/kernel/vmlinux.lds.S index b1002c6..5b7e69a 100644 --- a/arch/sparc/kernel/vmlinux.lds.S +++ b/arch/sparc/kernel/vmlinux.lds.S @@ -13,6 +13,7 @@ SECTIONS .text 0xf0004000 : { _text = .; + *(.text.head) TEXT_TEXT SCHED_TEXT LOCK_TEXT -- cgit v1.1 From 4bcc17dd8e48b612d43a9b0a6faa9eaa358fa4bd Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:37:04 +0000 Subject: alpha: pcibios_resource_to_bus() is callable from normal code pci_enable_rom(), specifically. Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/alpha/kernel/pci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/alpha/kernel/pci.c b/arch/alpha/kernel/pci.c index 5cf45fc..ff8cb63 100644 --- a/arch/alpha/kernel/pci.c +++ b/arch/alpha/kernel/pci.c @@ -338,7 +338,7 @@ common_swizzle(struct pci_dev *dev, u8 *pinp) return PCI_SLOT(dev->devfn); } -void __devinit +void pcibios_resource_to_bus(struct pci_dev *dev, struct pci_bus_region *region, struct resource *res) { -- cgit v1.1 From 2236d252e001ea57d53cec1954f680e503f3b8bc Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:37:34 +0000 Subject: enable_IR_x2apic() needs to be __init calls __init, called only from __init Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/x86/kernel/apic.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/apic.c b/arch/x86/kernel/apic.c index 04a7f96..16f9487 100644 --- a/arch/x86/kernel/apic.c +++ b/arch/x86/kernel/apic.c @@ -1315,7 +1315,7 @@ void enable_x2apic(void) } } -void enable_IR_x2apic(void) +void __init enable_IR_x2apic(void) { #ifdef CONFIG_INTR_REMAP int ret; -- cgit v1.1 From 23a14b9e9db49ed5f7683857557c26c874d4abb6 Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:37:44 +0000 Subject: kvm_setup_secondary_clock() is cpuinit Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/x86/kernel/kvmclock.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/kvmclock.c b/arch/x86/kernel/kvmclock.c index 1c9cc43..e169ae9 100644 --- a/arch/x86/kernel/kvmclock.c +++ b/arch/x86/kernel/kvmclock.c @@ -128,7 +128,7 @@ static int kvm_register_clock(char *txt) } #ifdef CONFIG_X86_LOCAL_APIC -static void __devinit kvm_setup_secondary_clock(void) +static void __cpuinit kvm_setup_secondary_clock(void) { /* * Now that the first cpu already had this clocksource initialized, -- cgit v1.1 From 37af46efa5413c6f4c25d9a24b4c43f2cc718eed Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:37:54 +0000 Subject: xen_setup_vcpu_info_placement() is not init on x86 ... so get xen-ops.h in agreement with xen/smp.c Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/x86/xen/xen-ops.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/xen/xen-ops.h b/arch/x86/xen/xen-ops.h index d7422dc..9e1afae 100644 --- a/arch/x86/xen/xen-ops.h +++ b/arch/x86/xen/xen-ops.h @@ -49,7 +49,7 @@ bool xen_vcpu_stolen(int vcpu); void xen_mark_init_mm_pinned(void); -void __init xen_setup_vcpu_info_placement(void); +void xen_setup_vcpu_info_placement(void); #ifdef CONFIG_SMP void xen_smp_init(void); -- cgit v1.1 From df6b07949b6cab9d119363d02ef63379160f6c82 Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:38:04 +0000 Subject: xen_play_dead() is __cpuinit Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/x86/xen/smp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/xen/smp.c b/arch/x86/xen/smp.c index d77da61..acd9b67 100644 --- a/arch/x86/xen/smp.c +++ b/arch/x86/xen/smp.c @@ -362,7 +362,7 @@ static void xen_cpu_die(unsigned int cpu) alternatives_smp_switch(0); } -static void xen_play_dead(void) +static void __cpuinit xen_play_dead(void) /* used only with CPU_HOTPLUG */ { play_dead_common(); HYPERVISOR_vcpu_op(VCPUOP_down, smp_processor_id(), NULL); -- cgit v1.1 From d3a307f32ec3554739033762672e533e2d246dae Mon Sep 17 00:00:00 2001 From: Al Viro Date: Sat, 22 Nov 2008 17:38:24 +0000 Subject: sn_pci_controller_fixup() should be __init called only from __init Signed-off-by: Al Viro Signed-off-by: Linus Torvalds --- arch/ia64/sn/kernel/io_init.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/ia64/sn/kernel/io_init.c b/arch/ia64/sn/kernel/io_init.c index c3aa851..4e1801b 100644 --- a/arch/ia64/sn/kernel/io_init.c +++ b/arch/ia64/sn/kernel/io_init.c @@ -292,7 +292,7 @@ EXPORT_SYMBOL(sn_io_slot_fixup); * sn_pci_controller_fixup() - This routine sets up a bus's resources * consistent with the Linux PCI abstraction layer. */ -static void +static void __init sn_pci_controller_fixup(int segment, int busnum, struct pci_bus *bus) { s64 status = 0; -- cgit v1.1 From 96b8936a9ed08746e47081458a5eb9e43a751e24 Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Tue, 25 Nov 2008 08:10:03 +0100 Subject: remove __ARCH_WANT_COMPAT_SYS_PTRACE All architectures now use the generic compat_sys_ptrace, as should every new architecture that needs 32bit compat (if we'll ever get another). Remove the now superflous __ARCH_WANT_COMPAT_SYS_PTRACE define, and also kill a comment about __ARCH_SYS_PTRACE that was added after __ARCH_SYS_PTRACE was already gone. Signed-off-by: Christoph Hellwig Acked-by: David S. Miller Signed-off-by: Linus Torvalds --- arch/Kconfig | 2 -- arch/ia64/include/asm/ptrace.h | 2 -- arch/mips/include/asm/ptrace.h | 4 ---- arch/parisc/include/asm/ptrace.h | 2 -- arch/powerpc/include/asm/ptrace.h | 2 -- arch/s390/include/asm/ptrace.h | 2 -- arch/sparc/include/asm/ptrace_64.h | 2 -- arch/x86/include/asm/ptrace.h | 2 -- 8 files changed, 18 deletions(-) (limited to 'arch') diff --git a/arch/Kconfig b/arch/Kconfig index 8977d99..471e72d 100644 --- a/arch/Kconfig +++ b/arch/Kconfig @@ -79,8 +79,6 @@ config HAVE_KRETPROBES # task_pt_regs() in asm/processor.h or asm/ptrace.h # arch_has_single_step() if there is hardware single-step support # arch_has_block_step() if there is hardware block-step support -# arch_ptrace() and not #define __ARCH_SYS_PTRACE -# compat_arch_ptrace() and #define __ARCH_WANT_COMPAT_SYS_PTRACE # asm/syscall.h supplying asm-generic/syscall.h interface # linux/regset.h user_regset interfaces # CORE_DUMP_USE_REGSET #define'd in linux/elf.h diff --git a/arch/ia64/include/asm/ptrace.h b/arch/ia64/include/asm/ptrace.h index 6417c1e..14055c6 100644 --- a/arch/ia64/include/asm/ptrace.h +++ b/arch/ia64/include/asm/ptrace.h @@ -325,8 +325,6 @@ static inline unsigned long user_stack_pointer(struct pt_regs *regs) #define arch_has_block_step() (1) extern void user_enable_block_step(struct task_struct *); -#define __ARCH_WANT_COMPAT_SYS_PTRACE - #endif /* !__KERNEL__ */ /* pt_all_user_regs is used for PTRACE_GETREGS PTRACE_SETREGS */ diff --git a/arch/mips/include/asm/ptrace.h b/arch/mips/include/asm/ptrace.h index 813abd1..c2c8bac 100644 --- a/arch/mips/include/asm/ptrace.h +++ b/arch/mips/include/asm/ptrace.h @@ -9,10 +9,6 @@ #ifndef _ASM_PTRACE_H #define _ASM_PTRACE_H -#ifdef CONFIG_64BIT -#define __ARCH_WANT_COMPAT_SYS_PTRACE -#endif - /* 0 - 31 are integer registers, 32 - 63 are fp registers. */ #define FPR_BASE 32 #define PC 64 diff --git a/arch/parisc/include/asm/ptrace.h b/arch/parisc/include/asm/ptrace.h index afa5333..302f68d 100644 --- a/arch/parisc/include/asm/ptrace.h +++ b/arch/parisc/include/asm/ptrace.h @@ -47,8 +47,6 @@ struct pt_regs { #define task_regs(task) ((struct pt_regs *) ((char *)(task) + TASK_REGS)) -#define __ARCH_WANT_COMPAT_SYS_PTRACE - struct task_struct; #define arch_has_single_step() 1 void user_disable_single_step(struct task_struct *task); diff --git a/arch/powerpc/include/asm/ptrace.h b/arch/powerpc/include/asm/ptrace.h index 280a90c..c9c678f 100644 --- a/arch/powerpc/include/asm/ptrace.h +++ b/arch/powerpc/include/asm/ptrace.h @@ -55,8 +55,6 @@ struct pt_regs { #ifdef __powerpc64__ -#define __ARCH_WANT_COMPAT_SYS_PTRACE - #define STACK_FRAME_OVERHEAD 112 /* size of minimum stack frame */ #define STACK_FRAME_LR_SAVE 2 /* Location of LR in stack frame */ #define STACK_FRAME_REGS_MARKER ASM_CONST(0x7265677368657265) diff --git a/arch/s390/include/asm/ptrace.h b/arch/s390/include/asm/ptrace.h index a7226f8..560ce85 100644 --- a/arch/s390/include/asm/ptrace.h +++ b/arch/s390/include/asm/ptrace.h @@ -486,8 +486,6 @@ struct task_struct; extern void user_enable_single_step(struct task_struct *); extern void user_disable_single_step(struct task_struct *); -#define __ARCH_WANT_COMPAT_SYS_PTRACE - #define user_mode(regs) (((regs)->psw.mask & PSW_MASK_PSTATE) != 0) #define instruction_pointer(regs) ((regs)->psw.addr & PSW_ADDR_INSN) #define user_stack_pointer(regs)((regs)->gprs[15]) diff --git a/arch/sparc/include/asm/ptrace_64.h b/arch/sparc/include/asm/ptrace_64.h index 3d3e9c1..84e969f 100644 --- a/arch/sparc/include/asm/ptrace_64.h +++ b/arch/sparc/include/asm/ptrace_64.h @@ -142,8 +142,6 @@ struct global_reg_snapshot { }; extern struct global_reg_snapshot global_reg_snapshot[NR_CPUS]; -#define __ARCH_WANT_COMPAT_SYS_PTRACE - #define force_successful_syscall_return() \ do { current_thread_info()->syscall_noerror = 1; \ } while (0) diff --git a/arch/x86/include/asm/ptrace.h b/arch/x86/include/asm/ptrace.h index d1531c8..eefb059 100644 --- a/arch/x86/include/asm/ptrace.h +++ b/arch/x86/include/asm/ptrace.h @@ -271,8 +271,6 @@ extern int do_get_thread_area(struct task_struct *p, int idx, extern int do_set_thread_area(struct task_struct *p, int idx, struct user_desc __user *info, int can_allocate); -#define __ARCH_WANT_COMPAT_SYS_PTRACE - #endif /* __KERNEL__ */ #endif /* !__ASSEMBLY__ */ -- cgit v1.1 From 499c59c42967329d39481314a839d7669f5e1506 Mon Sep 17 00:00:00 2001 From: "Robert P. J. Day" Date: Fri, 28 Nov 2008 11:48:37 +0000 Subject: MN10300: Tighten up the code using case ranges Compress a set of consecutive switch cases into a case-range. Signed-off-by: Robert P. J. Day Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- arch/mn10300/kernel/gdb-stub.c | 24 ++---------------------- 1 file changed, 2 insertions(+), 22 deletions(-) (limited to 'arch') diff --git a/arch/mn10300/kernel/gdb-stub.c b/arch/mn10300/kernel/gdb-stub.c index 54be6af..0ea7482 100644 --- a/arch/mn10300/kernel/gdb-stub.c +++ b/arch/mn10300/kernel/gdb-stub.c @@ -522,17 +522,7 @@ static int gdbstub_single_step(struct pt_regs *regs) } else { switch (cur) { /* Bxx (d8,PC) */ - case 0xc0: - case 0xc1: - case 0xc2: - case 0xc3: - case 0xc4: - case 0xc5: - case 0xc6: - case 0xc7: - case 0xc8: - case 0xc9: - case 0xca: + case 0xc0 ... 0xca: if (gdbstub_read_byte(pc + 1, (u8 *) &x) < 0) goto fault; if (!__gdbstub_mark_bp(pc + 2, 0)) @@ -543,17 +533,7 @@ static int gdbstub_single_step(struct pt_regs *regs) break; /* LXX (d8,PC) */ - case 0xd0: - case 0xd1: - case 0xd2: - case 0xd3: - case 0xd4: - case 0xd5: - case 0xd6: - case 0xd7: - case 0xd8: - case 0xd9: - case 0xda: + case 0xd0 ... 0xda: if (!__gdbstub_mark_bp(pc + 1, 0)) goto fault; if (regs->pc != regs->lar && -- cgit v1.1 From 4b824de9b18b8d1013e9fc9e4b0f855ced8cac2c Mon Sep 17 00:00:00 2001 From: Adhemerval Zanella Date: Wed, 19 Nov 2008 03:55:35 +0000 Subject: powerpc: Fix IRQ assignment for some PCIe devices Currently, some PCIe devices on POWER6 machines do not get interrupts assigned correctly. The problem is that OF doesn't create an "interrupt" property for them. The fix is for of_irq_map_pci to fall back to using the value in the PCI interrupt-pin register in config space, as we do when there is no OF device-tree node for the device. I have verified that this works fine with a pair of Squib-E SAS adapter on a P6-570. Acked-by: Benjamin Herrenschmidt Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/prom_parse.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/prom_parse.c b/arch/powerpc/kernel/prom_parse.c index bc1fb27..a11d689 100644 --- a/arch/powerpc/kernel/prom_parse.c +++ b/arch/powerpc/kernel/prom_parse.c @@ -250,8 +250,11 @@ int of_irq_map_pci(struct pci_dev *pdev, struct of_irq *out_irq) * parsing */ dn = pci_device_to_OF_node(pdev); - if (dn) - return of_irq_map_one(dn, 0, out_irq); + if (dn) { + rc = of_irq_map_one(dn, 0, out_irq); + if (!rc) + return rc; + } /* Ok, we don't, time to have fun. Let's start by building up an * interrupt spec. we assume #interrupt-cells is 1, which is standard -- cgit v1.1 From 4a6186696e7f15b3ea4dafcdb64ee0703e0e4487 Mon Sep 17 00:00:00 2001 From: Dave Hansen Date: Mon, 24 Nov 2008 12:02:35 +0000 Subject: powerpc: Fix boot freeze on machine with empty memory node I got a bug report about a distro kernel not booting on a particular machine. It would freeze during boot: > ... > Could not find start_pfn for node 1 > [boot]0015 Setup Done > Built 2 zonelists in Node order, mobility grouping on. Total pages: 123783 > Policy zone: DMA > Kernel command line: > [boot]0020 XICS Init > [boot]0021 XICS Done > PID hash table entries: 4096 (order: 12, 32768 bytes) > clocksource: timebase mult[7d0000] shift[22] registered > Console: colour dummy device 80x25 > console handover: boot [udbg0] -> real [hvc0] > Dentry cache hash table entries: 1048576 (order: 7, 8388608 bytes) > Inode-cache hash table entries: 524288 (order: 6, 4194304 bytes) > freeing bootmem node 0 I've reproduced this on 2.6.27.7. It is caused by commit 8f64e1f2d1e09267ac926e15090fd505c1c0cbcb ("powerpc: Reserve in bootmem lmb reserved regions that cross NUMA nodes"). The problem is that Jon took a loop which was (in pseudocode): for_each_node(nid) NODE_DATA(nid) = careful_alloc(nid); setup_bootmem(nid); reserve_node_bootmem(nid); and broke it up into: for_each_node(nid) NODE_DATA(nid) = careful_alloc(nid); setup_bootmem(nid); for_each_node(nid) reserve_node_bootmem(nid); The issue comes in when the 'careful_alloc()' is called on a node with no memory. It falls back to using bootmem from a previously-initialized node. But, bootmem has not yet been reserved when Jon's patch is applied. It gives back bogus memory (0xc000000000000000) and pukes later in boot. The following patch collapses the loop back together. It also breaks the mark_reserved_regions_for_nid() code out into a function and adds some comments. I think a huge part of introducing this bug is because for loop was too long and hard to read. The actual bug fix here is the: + if (end_pfn <= node->node_start_pfn || + start_pfn >= node_end_pfn) + continue; Signed-off-by: Dave Hansen Signed-off-by: Paul Mackerras --- arch/powerpc/mm/numa.c | 122 ++++++++++++++++++++++++++++++------------------- 1 file changed, 75 insertions(+), 47 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/mm/numa.c b/arch/powerpc/mm/numa.c index eb505ad..a8397bb 100644 --- a/arch/powerpc/mm/numa.c +++ b/arch/powerpc/mm/numa.c @@ -865,6 +865,67 @@ static struct notifier_block __cpuinitdata ppc64_numa_nb = { .priority = 1 /* Must run before sched domains notifier. */ }; +static void mark_reserved_regions_for_nid(int nid) +{ + struct pglist_data *node = NODE_DATA(nid); + int i; + + for (i = 0; i < lmb.reserved.cnt; i++) { + unsigned long physbase = lmb.reserved.region[i].base; + unsigned long size = lmb.reserved.region[i].size; + unsigned long start_pfn = physbase >> PAGE_SHIFT; + unsigned long end_pfn = ((physbase + size) >> PAGE_SHIFT); + struct node_active_region node_ar; + unsigned long node_end_pfn = node->node_start_pfn + + node->node_spanned_pages; + + /* + * Check to make sure that this lmb.reserved area is + * within the bounds of the node that we care about. + * Checking the nid of the start and end points is not + * sufficient because the reserved area could span the + * entire node. + */ + if (end_pfn <= node->node_start_pfn || + start_pfn >= node_end_pfn) + continue; + + get_node_active_region(start_pfn, &node_ar); + while (start_pfn < end_pfn && + node_ar.start_pfn < node_ar.end_pfn) { + unsigned long reserve_size = size; + /* + * if reserved region extends past active region + * then trim size to active region + */ + if (end_pfn > node_ar.end_pfn) + reserve_size = (node_ar.end_pfn << PAGE_SHIFT) + - (start_pfn << PAGE_SHIFT); + dbg("reserve_bootmem %lx %lx nid=%d\n", physbase, + reserve_size, node_ar.nid); + reserve_bootmem_node(NODE_DATA(node_ar.nid), physbase, + reserve_size, BOOTMEM_DEFAULT); + /* + * if reserved region is contained in the active region + * then done. + */ + if (end_pfn <= node_ar.end_pfn) + break; + + /* + * reserved region extends past the active region + * get next active region that contains this + * reserved region + */ + start_pfn = node_ar.end_pfn; + physbase = start_pfn << PAGE_SHIFT; + size = size - reserve_size; + get_node_active_region(start_pfn, &node_ar); + } + } +} + + void __init do_init_bootmem(void) { int nid; @@ -890,7 +951,13 @@ void __init do_init_bootmem(void) get_pfn_range_for_nid(nid, &start_pfn, &end_pfn); - /* Allocate the node structure node local if possible */ + /* + * Allocate the node structure node local if possible + * + * Be careful moving this around, as it relies on all + * previous nodes' bootmem to be initialized and have + * all reserved areas marked. + */ NODE_DATA(nid) = careful_allocation(nid, sizeof(struct pglist_data), SMP_CACHE_BYTES, end_pfn); @@ -922,53 +989,14 @@ void __init do_init_bootmem(void) start_pfn, end_pfn); free_bootmem_with_active_regions(nid, end_pfn); - } - - /* Mark reserved regions */ - for (i = 0; i < lmb.reserved.cnt; i++) { - unsigned long physbase = lmb.reserved.region[i].base; - unsigned long size = lmb.reserved.region[i].size; - unsigned long start_pfn = physbase >> PAGE_SHIFT; - unsigned long end_pfn = ((physbase + size) >> PAGE_SHIFT); - struct node_active_region node_ar; - - get_node_active_region(start_pfn, &node_ar); - while (start_pfn < end_pfn && - node_ar.start_pfn < node_ar.end_pfn) { - unsigned long reserve_size = size; - /* - * if reserved region extends past active region - * then trim size to active region - */ - if (end_pfn > node_ar.end_pfn) - reserve_size = (node_ar.end_pfn << PAGE_SHIFT) - - (start_pfn << PAGE_SHIFT); - dbg("reserve_bootmem %lx %lx nid=%d\n", physbase, - reserve_size, node_ar.nid); - reserve_bootmem_node(NODE_DATA(node_ar.nid), physbase, - reserve_size, BOOTMEM_DEFAULT); - /* - * if reserved region is contained in the active region - * then done. - */ - if (end_pfn <= node_ar.end_pfn) - break; - - /* - * reserved region extends past the active region - * get next active region that contains this - * reserved region - */ - start_pfn = node_ar.end_pfn; - physbase = start_pfn << PAGE_SHIFT; - size = size - reserve_size; - get_node_active_region(start_pfn, &node_ar); - } - - } - - for_each_online_node(nid) + /* + * Be very careful about moving this around. Future + * calls to careful_allocation() depend on this getting + * done correctly. + */ + mark_reserved_regions_for_nid(nid); sparse_memory_present_with_active_regions(nid); + } } void __init paging_init(void) -- cgit v1.1 From d015fe9951641b2d869a7ae4a690be2a05a9dc7f Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Fri, 28 Nov 2008 09:51:22 +0000 Subject: powerpc/cell/axon-msi: Retry on missing interrupt The MSI capture logic for the axon bridge can sometimes lose interrupts in case of high DMA and interrupt load, when it signals an MSI interrupt to the MPIC interrupt controller while we are already handling another MSI. Each MSI vector gets written into a FIFO buffer in main memory using DMA, and that DMA access is normally flushed by the actual interrupt packet on the IOIF. An MMIO register in the MSIC holds the position of the last entry in the FIFO buffer that was written. However, reading that position does not flush the DMA, so that we can observe stale data in the buffer. In a stress test, we have observed the DMA to arrive up to 14 microseconds after reading the register. This patch works around this problem by retrying the access to the FIFO buffer. We can reliably detect the conditioning by writing an invalid MSI vector into the FIFO buffer after reading from it, assuming that all MSIs we get are valid. After detecting an invalid MSI vector, we udelay(1) in the interrupt cascade for up to 100 times before giving up. Signed-off-by: Arnd Bergmann Signed-off-by: Paul Mackerras --- arch/powerpc/platforms/cell/axon_msi.c | 36 +++++++++++++++++++++++++++++----- 1 file changed, 31 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/cell/axon_msi.c b/arch/powerpc/platforms/cell/axon_msi.c index 896548b..442cf36 100644 --- a/arch/powerpc/platforms/cell/axon_msi.c +++ b/arch/powerpc/platforms/cell/axon_msi.c @@ -95,6 +95,7 @@ static void axon_msi_cascade(unsigned int irq, struct irq_desc *desc) struct axon_msic *msic = get_irq_data(irq); u32 write_offset, msi; int idx; + int retry = 0; write_offset = dcr_read(msic->dcr_host, MSIC_WRITE_OFFSET_REG); pr_debug("axon_msi: original write_offset 0x%x\n", write_offset); @@ -102,7 +103,7 @@ static void axon_msi_cascade(unsigned int irq, struct irq_desc *desc) /* write_offset doesn't wrap properly, so we have to mask it */ write_offset &= MSIC_FIFO_SIZE_MASK; - while (msic->read_offset != write_offset) { + while (msic->read_offset != write_offset && retry < 100) { idx = msic->read_offset / sizeof(__le32); msi = le32_to_cpu(msic->fifo_virt[idx]); msi &= 0xFFFF; @@ -110,13 +111,37 @@ static void axon_msi_cascade(unsigned int irq, struct irq_desc *desc) pr_debug("axon_msi: woff %x roff %x msi %x\n", write_offset, msic->read_offset, msi); + if (msi < NR_IRQS && irq_map[msi].host == msic->irq_host) { + generic_handle_irq(msi); + msic->fifo_virt[idx] = cpu_to_le32(0xffffffff); + } else { + /* + * Reading the MSIC_WRITE_OFFSET_REG does not + * reliably flush the outstanding DMA to the + * FIFO buffer. Here we were reading stale + * data, so we need to retry. + */ + udelay(1); + retry++; + pr_debug("axon_msi: invalid irq 0x%x!\n", msi); + continue; + } + + if (retry) { + pr_debug("axon_msi: late irq 0x%x, retry %d\n", + msi, retry); + retry = 0; + } + msic->read_offset += MSIC_FIFO_ENTRY_SIZE; msic->read_offset &= MSIC_FIFO_SIZE_MASK; + } - if (msi < NR_IRQS && irq_map[msi].host == msic->irq_host) - generic_handle_irq(msi); - else - pr_debug("axon_msi: invalid irq 0x%x!\n", msi); + if (retry) { + printk(KERN_WARNING "axon_msi: irq timed out\n"); + + msic->read_offset += MSIC_FIFO_ENTRY_SIZE; + msic->read_offset &= MSIC_FIFO_SIZE_MASK; } desc->chip->eoi(irq); @@ -364,6 +389,7 @@ static int axon_msi_probe(struct of_device *device, dn->full_name); goto out_free_fifo; } + memset(msic->fifo_virt, 0xff, MSIC_FIFO_SIZE_BYTES); msic->irq_host = irq_alloc_host(dn, IRQ_HOST_MAP_NOMAP, NR_IRQS, &msic_host_ops, 0); -- cgit v1.1 From cc353c30bbdb84f4317a6c149ebb11cde2232e40 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Fri, 28 Nov 2008 09:51:23 +0000 Subject: powerpc/mpic: Don't reset affinity for secondary MPIC on boot Kexec/kdump currently fails on the IBM QS2x blades when the kexec happens on a CPU other than the initial boot CPU. It turns out that this is the result of mpic_init trying to set affinity of each interrupt vector to the current boot CPU. As far as I can tell, the same problem is likely to exist on any secondary MPIC, because they have to deliver interrupts to the first output all the time. There are two potential solutions for this: either not set up affinity at all for secondary MPICs, or assume that a single CPU output is connected to the upstream interrupt controller and hardcode affinity to that per architecture. This patch implements the second approach, defaulting to the first output. Currently, all known secondary MPICs are routed to their upstream port using the first destination, so we hardcode that. Signed-off-by: Arnd Bergmann Signed-off-by: Paul Mackerras --- arch/powerpc/sysdev/mpic.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/mpic.c b/arch/powerpc/sysdev/mpic.c index f6299cc..b24e1d08 100644 --- a/arch/powerpc/sysdev/mpic.c +++ b/arch/powerpc/sysdev/mpic.c @@ -1271,6 +1271,7 @@ void __init mpic_set_default_senses(struct mpic *mpic, u8 *senses, int count) void __init mpic_init(struct mpic *mpic) { int i; + int cpu; BUG_ON(mpic->num_sources == 0); @@ -1313,6 +1314,11 @@ void __init mpic_init(struct mpic *mpic) mpic_pasemi_msi_init(mpic); + if (mpic->flags & MPIC_PRIMARY) + cpu = hard_smp_processor_id(); + else + cpu = 0; + for (i = 0; i < mpic->num_sources; i++) { /* start with vector = source number, and masked */ u32 vecpri = MPIC_VECPRI_MASK | i | @@ -1323,8 +1329,7 @@ void __init mpic_init(struct mpic *mpic) continue; /* init hw */ mpic_irq_write(i, MPIC_INFO(IRQ_VECTOR_PRI), vecpri); - mpic_irq_write(i, MPIC_INFO(IRQ_DESTINATION), - 1 << hard_smp_processor_id()); + mpic_irq_write(i, MPIC_INFO(IRQ_DESTINATION), 1 << cpu); } /* Init spurious vector */ -- cgit v1.1 From 960cedb4e3eedec6394f224fc832c7a23f35a799 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Fri, 28 Nov 2008 09:51:24 +0000 Subject: powerpc/cell: Fix GDB watchpoints, again An earlier patch from Jens Osterkamp attempted to fix GDB watchpoints by enabling the DABRX register at boot time. Unfortunately, this did not work on SMP setups, where secondary CPUs were still using the power-on DABRX value. This introduces the same change for secondary CPUs on cell as well. Reported-by: Ulrich Weigand Tested-by: Ulrich Weigand Signed-off-by: Arnd Bergmann Signed-off-by: Paul Mackerras --- arch/powerpc/platforms/cell/smp.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/platforms/cell/smp.c b/arch/powerpc/platforms/cell/smp.c index c0d86e1..9046803 100644 --- a/arch/powerpc/platforms/cell/smp.c +++ b/arch/powerpc/platforms/cell/smp.c @@ -129,10 +129,15 @@ static int __init smp_iic_probe(void) return cpus_weight(cpu_possible_map); } -static void __devinit smp_iic_setup_cpu(int cpu) +static void __devinit smp_cell_setup_cpu(int cpu) { if (cpu != boot_cpuid) iic_setup_cpu(); + + /* + * change default DABRX to allow user watchpoints + */ + mtspr(SPRN_DABRX, DABRX_KERNEL | DABRX_USER); } static DEFINE_SPINLOCK(timebase_lock); @@ -192,7 +197,7 @@ static struct smp_ops_t bpa_iic_smp_ops = { .message_pass = smp_iic_message_pass, .probe = smp_iic_probe, .kick_cpu = smp_cell_kick_cpu, - .setup_cpu = smp_iic_setup_cpu, + .setup_cpu = smp_cell_setup_cpu, .cpu_bootable = smp_cell_cpu_bootable, }; -- cgit v1.1 From ab598b6680f1e74c267d1547ee352f3e1e530f89 Mon Sep 17 00:00:00 2001 From: Paul Mackerras Date: Sun, 30 Nov 2008 11:49:45 +0000 Subject: powerpc: Fix system calls on Cell entered with XER.SO=1 It turns out that on Cell, on a kernel with CONFIG_VIRT_CPU_ACCOUNTING = y, if a program sets the SO (summary overflow) bit in the XER and then does a system call, the SO bit in CR0 will be set on return regardless of whether the system call detected an error. Since CR0.SO is used as the error indication from the system call, this means that all system calls appear to fail. The reason is that the workaround for the timebase bug on Cell uses a compare instruction. With CONFIG_VIRT_CPU_ACCOUNTING = y, the ACCOUNT_CPU_USER_ENTRY macro reads the timebase, so we end up doing a compare instruction, which copies XER.SO to CR0.SO. Since we were doing this in the system call entry patch after clearing CR0.SO but before saving the CR, this meant that the saved CR image had CR0.SO set if XER.SO was set on entry. This fixes it by moving the clearing of CR0.SO to after the ACCOUNT_CPU_USER_ENTRY call in the system call entry path. Signed-off-by: Paul Mackerras Acked-by: Arnd Bergmann Acked-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/entry_64.S | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S index e6d5284..e0bcf93 100644 --- a/arch/powerpc/kernel/entry_64.S +++ b/arch/powerpc/kernel/entry_64.S @@ -57,12 +57,18 @@ system_call_common: beq- 1f ld r1,PACAKSAVE(r13) 1: std r10,0(r1) - crclr so std r11,_NIP(r1) std r12,_MSR(r1) std r0,GPR0(r1) std r10,GPR1(r1) ACCOUNT_CPU_USER_ENTRY(r10, r11) + /* + * This "crclr so" clears CR0.SO, which is the error indication on + * return from this system call. There must be no cmp instruction + * between it and the "mfcr r9" below, otherwise if XER.SO is set, + * CR0.SO will get set, causing all system calls to appear to fail. + */ + crclr so std r2,GPR2(r1) std r3,GPR3(r1) std r4,GPR4(r1) -- cgit v1.1 From a1e0eb104249817e5251bd4aade50921ffcb2159 Mon Sep 17 00:00:00 2001 From: Milton Miller Date: Sun, 16 Nov 2008 11:44:42 +0000 Subject: powerpc: Fix build for 32-bit SMP configs MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit attr_smt_snooze_delay is only defined for CONFIG_PPC64, so protect the attribute removal with the same condition. This fixes this build error on 32-bit SMP configurations: /data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c: In function ‘unregister_cpu_online’: /data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: ‘attr_smt_snooze_delay’ undeclared (first use in this function) /data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: (Each undeclared identifier is reported only once /data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: for each function it appears in.) Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/sysfs.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/kernel/sysfs.c b/arch/powerpc/kernel/sysfs.c index 86a2ffc..20885a3 100644 --- a/arch/powerpc/kernel/sysfs.c +++ b/arch/powerpc/kernel/sysfs.c @@ -717,9 +717,11 @@ static void unregister_cpu_online(unsigned int cpu) BUG_ON(!c->hotpluggable); +#ifdef CONFIG_PPC64 if (!firmware_has_feature(FW_FEATURE_ISERIES) && cpu_has_feature(CPU_FTR_SMT)) sysdev_remove_file(s, &attr_smt_snooze_delay); +#endif /* PMC stuff */ switch (cur_cpu_spec->pmc_type) { -- cgit v1.1 From 43714539eab42b2fa3653ea7bd667b36c2291b11 Mon Sep 17 00:00:00 2001 From: Mahesh Salgaonkar Date: Sat, 29 Nov 2008 16:50:12 +0530 Subject: sched: don't export sched_mc_power_savings in laptops Impact: do not expose a control that has no effect Fix to prevent sched_mc_power_saving from being exported through sysfs on single-socket systems. (Say multicore single socket (Laptop)) CPU core map of the boot cpu should be equal to possible number of cpus for single socket system. This fix has been developed at FOSS.in kernel workout. Signed-off-by: Mahesh Salgaonkar Acked-by: Peter Zijlstra Signed-off-by: Ingo Molnar --- arch/x86/include/asm/topology.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/include/asm/topology.h b/arch/x86/include/asm/topology.h index 4850e4b..ff386ff 100644 --- a/arch/x86/include/asm/topology.h +++ b/arch/x86/include/asm/topology.h @@ -239,7 +239,7 @@ struct pci_bus; void set_pci_bus_resources_arch_default(struct pci_bus *b); #ifdef CONFIG_SMP -#define mc_capable() (boot_cpu_data.x86_max_cores > 1) +#define mc_capable() (cpus_weight(per_cpu(cpu_core_map, 0)) != nr_cpu_ids) #define smt_capable() (smp_num_siblings > 1) #endif -- cgit v1.1 From b270ee8a9fc9547eb781ce9ccd379450bcf9a204 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 1 Dec 2008 02:48:26 -0800 Subject: sparc64: Fix offset calculation in compute_size() The fault address is somewhere inside of the buffer, not before it. Signed-off-by: David S. Miller --- arch/sparc64/lib/user_fixup.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/sparc64/lib/user_fixup.c b/arch/sparc64/lib/user_fixup.c index 19d1fdb..05a361b 100644 --- a/arch/sparc64/lib/user_fixup.c +++ b/arch/sparc64/lib/user_fixup.c @@ -24,7 +24,7 @@ static unsigned long compute_size(unsigned long start, unsigned long size, unsig if (fault_addr < start || fault_addr >= end) { *offset = 0; } else { - *offset = start - fault_addr; + *offset = fault_addr - start; size = end - fault_addr; } return size; -- cgit v1.1 From 33b07db9f38fe73b3895f8d4db8fdee03e3afec3 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Mon, 1 Dec 2008 07:55:14 -0800 Subject: Revert "of_platform_driver noise on sparce" This reverts commit e669dae6141ff97d3c7566207f5de3b487dcf837, since it is incomplete, and clashes with fuller patches and the sparc 32/64 unification effort. Requested-by: David Miller Acked-by: Al Viro Signed-off-by: Linus Torvalds --- arch/sparc64/kernel/pci_fire.c | 2 +- arch/sparc64/kernel/pci_psycho.c | 4 ++-- arch/sparc64/kernel/pci_sun4v.c | 2 +- 3 files changed, 4 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/sparc64/kernel/pci_fire.c b/arch/sparc64/kernel/pci_fire.c index fcbbac6..9462b68 100644 --- a/arch/sparc64/kernel/pci_fire.c +++ b/arch/sparc64/kernel/pci_fire.c @@ -455,7 +455,7 @@ static int __init pci_fire_pbm_init(struct pci_pbm_info *pbm, return 0; } -static int __init fire_probe(struct of_device *op, +static int __devinit fire_probe(struct of_device *op, const struct of_device_id *match) { struct device_node *dp = op->node; diff --git a/arch/sparc64/kernel/pci_psycho.c b/arch/sparc64/kernel/pci_psycho.c index 56605ad..dfb3ec8 100644 --- a/arch/sparc64/kernel/pci_psycho.c +++ b/arch/sparc64/kernel/pci_psycho.c @@ -493,7 +493,7 @@ static void __init psycho_pbm_init(struct pci_pbm_info *pbm, psycho_scan_bus(pbm, &op->dev); } -static struct pci_pbm_info * __init psycho_find_sibling(u32 upa_portid) +static struct pci_pbm_info * __devinit psycho_find_sibling(u32 upa_portid) { struct pci_pbm_info *pbm; @@ -506,7 +506,7 @@ static struct pci_pbm_info * __init psycho_find_sibling(u32 upa_portid) #define PSYCHO_CONFIGSPACE 0x001000000UL -static int __init psycho_probe(struct of_device *op, +static int __devinit psycho_probe(struct of_device *op, const struct of_device_id *match) { const struct linux_prom64_registers *pr_regs; diff --git a/arch/sparc64/kernel/pci_sun4v.c b/arch/sparc64/kernel/pci_sun4v.c index 4b27b0e..34a1fde 100644 --- a/arch/sparc64/kernel/pci_sun4v.c +++ b/arch/sparc64/kernel/pci_sun4v.c @@ -929,7 +929,7 @@ static int __init pci_sun4v_pbm_init(struct pci_pbm_info *pbm, return 0; } -static int __init pci_sun4v_probe(struct of_device *op, +static int __devinit pci_sun4v_probe(struct of_device *op, const struct of_device_id *match) { const struct linux_prom64_registers *regs; -- cgit v1.1 From 020f97063dd68a8e3b9aac928ac49a438b7416ce Mon Sep 17 00:00:00 2001 From: Russell King Date: Mon, 1 Dec 2008 17:40:54 +0000 Subject: [ARM] omap: fix a pile of issues This patch fixes a number of sillies, from missing 'const' to using 'return' in void functions, to functions with no arguments not even 'void' and a cast which isn't required. Acked-by: Tony Lindgren Signed-off-by: Russell King --- arch/arm/mach-omap1/io.c | 2 +- arch/arm/plat-omap/include/mach/omapfb.h | 4 ++-- arch/arm/plat-omap/sram.c | 8 ++++---- 3 files changed, 7 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-omap1/io.c b/arch/arm/mach-omap1/io.c index b3bd8ca..4c3e582 100644 --- a/arch/arm/mach-omap1/io.c +++ b/arch/arm/mach-omap1/io.c @@ -128,7 +128,7 @@ void __init omap1_map_common_io(void) * Common low-level hardware init for omap1. This should only get called from * board specific init. */ -void __init omap1_init_common_hw() +void __init omap1_init_common_hw(void) { /* REVISIT: Refer to OMAP5910 Errata, Advisory SYS_1: "Timeout Abort * on a Posted Write in the TIPB Bridge". diff --git a/arch/arm/plat-omap/include/mach/omapfb.h b/arch/arm/plat-omap/include/mach/omapfb.h index ec67fb4..7b74d12 100644 --- a/arch/arm/plat-omap/include/mach/omapfb.h +++ b/arch/arm/plat-omap/include/mach/omapfb.h @@ -353,8 +353,8 @@ struct omapfb_device { u32 pseudo_palette[17]; struct lcd_panel *panel; /* LCD panel */ - struct lcd_ctrl *ctrl; /* LCD controller */ - struct lcd_ctrl *int_ctrl; /* internal LCD ctrl */ + const struct lcd_ctrl *ctrl; /* LCD controller */ + const struct lcd_ctrl *int_ctrl; /* internal LCD ctrl */ struct lcd_ctrl_extif *ext_if; /* LCD ctrl external interface */ struct device *dev; diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index 9f9a921..dcd9d16 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -255,7 +255,7 @@ void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl) if (!_omap_sram_reprogram_clock) omap_sram_error(); - return _omap_sram_reprogram_clock(dpllctl, ckctl); + _omap_sram_reprogram_clock(dpllctl, ckctl); } int __init omap1_sram_init(void) @@ -282,8 +282,8 @@ void omap2_sram_ddr_init(u32 *slow_dll_ctrl, u32 fast_dll_ctrl, if (!_omap2_sram_ddr_init) omap_sram_error(); - return _omap2_sram_ddr_init(slow_dll_ctrl, fast_dll_ctrl, - base_cs, force_unlock); + _omap2_sram_ddr_init(slow_dll_ctrl, fast_dll_ctrl, + base_cs, force_unlock); } static void (*_omap2_sram_reprogram_sdrc)(u32 perf_level, u32 dll_val, @@ -294,7 +294,7 @@ void omap2_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, u32 mem_type) if (!_omap2_sram_reprogram_sdrc) omap_sram_error(); - return _omap2_sram_reprogram_sdrc(perf_level, dll_val, mem_type); + _omap2_sram_reprogram_sdrc(perf_level, dll_val, mem_type); } static u32 (*_omap2_set_prcm)(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); -- cgit v1.1 From b93c35ff39d19f20c47c06c206986afefecc777a Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 1 Dec 2008 13:13:57 -0800 Subject: spi: fix spi_s3c24xx_gpio num_chipselect The spi master driver must have num_chipselect set to allow the bus to initialise. Pass this through the platform data. Signed-off-by: Ben Dooks Signed-off-by: David Brownell Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/arm/mach-s3c2410/include/mach/spi-gpio.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/mach-s3c2410/include/mach/spi-gpio.h b/arch/arm/mach-s3c2410/include/mach/spi-gpio.h index 3fe8be9..980a099 100644 --- a/arch/arm/mach-s3c2410/include/mach/spi-gpio.h +++ b/arch/arm/mach-s3c2410/include/mach/spi-gpio.h @@ -18,6 +18,7 @@ struct s3c2410_spigpio_info { unsigned long pin_mosi; unsigned long pin_miso; + int num_chipselect; int bus_num; void (*chip_select)(struct s3c2410_spigpio_info *spi, int cs); -- cgit v1.1 From 4280e3126f641898f0ed1a931645373d3489e2a6 Mon Sep 17 00:00:00 2001 From: David Howells Date: Mon, 1 Dec 2008 13:14:00 -0800 Subject: frv: fix mmap2 error handling Fix the error handling in sys_mmap2(). Currently, if the pgoff check fails, fput() might have to be called (which it isn't), so do the pgoff check first, before fget() is called. Signed-off-by: David Howells Reported-by: Julia Lawall Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/frv/kernel/sys_frv.c | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/frv/kernel/sys_frv.c b/arch/frv/kernel/sys_frv.c index 49b2cf2..baadc97 100644 --- a/arch/frv/kernel/sys_frv.c +++ b/arch/frv/kernel/sys_frv.c @@ -35,22 +35,21 @@ asmlinkage long sys_mmap2(unsigned long addr, unsigned long len, int error = -EBADF; struct file * file = NULL; - flags &= ~(MAP_EXECUTABLE | MAP_DENYWRITE); - if (!(flags & MAP_ANONYMOUS)) { - file = fget(fd); - if (!file) - goto out; - } - /* As with sparc32, make sure the shift for mmap2 is constant (12), no matter what PAGE_SIZE we have.... */ /* But unlike sparc32, don't just silently break if we're trying to map something we can't */ - if (pgoff & ((1<<(PAGE_SHIFT-12))-1)) + if (pgoff & ((1 << (PAGE_SHIFT - 12)) - 1)) return -EINVAL; + pgoff >>= PAGE_SHIFT - 12; - pgoff >>= (PAGE_SHIFT - 12); + flags &= ~(MAP_EXECUTABLE | MAP_DENYWRITE); + if (!(flags & MAP_ANONYMOUS)) { + file = fget(fd); + if (!file) + goto out; + } down_write(¤t->mm->mmap_sem); error = do_mmap_pgoff(file, addr, len, prot, flags, pgoff); -- cgit v1.1 From ae4e1434a03207661b4331ea715d3f18cb479123 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Tue, 2 Dec 2008 20:58:26 +0100 Subject: m68k: Update defconfigs for 2.6.28-rc7 Signed-off-by: Geert Uytterhoeven --- arch/m68k/configs/amiga_defconfig | 126 ++++++++++++++++++--------------- arch/m68k/configs/apollo_defconfig | 115 ++++++++++++++++++------------- arch/m68k/configs/atari_defconfig | 130 ++++++++++++++++++++--------------- arch/m68k/configs/bvme6000_defconfig | 112 +++++++++++++++++------------- arch/m68k/configs/hp300_defconfig | 115 ++++++++++++++++++------------- arch/m68k/configs/mac_defconfig | 125 ++++++++++++++++++--------------- arch/m68k/configs/multi_defconfig | 129 +++++++++++++++++++--------------- arch/m68k/configs/mvme147_defconfig | 112 +++++++++++++++++------------- arch/m68k/configs/mvme16x_defconfig | 112 +++++++++++++++++------------- arch/m68k/configs/q40_defconfig | 125 +++++++++++++++++++-------------- arch/m68k/configs/sun3_defconfig | 124 +++++++++++++++++++-------------- arch/m68k/configs/sun3x_defconfig | 115 ++++++++++++++++++------------- 12 files changed, 828 insertions(+), 612 deletions(-) (limited to 'arch') diff --git a/arch/m68k/configs/amiga_defconfig b/arch/m68k/configs/amiga_defconfig index 8bd61a64..23597be 100644 --- a/arch/m68k/configs/amiga_defconfig +++ b/arch/m68k/configs/amiga_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:00 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:42 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set CONFIG_AMIGA=y # CONFIG_ATARI is not set # CONFIG_MAC is not set @@ -148,19 +138,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_ZORRO=y @@ -212,7 +204,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -262,13 +253,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -282,19 +274,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -302,20 +297,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -323,8 +318,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -337,9 +332,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -351,16 +346,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -387,6 +382,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -410,19 +406,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -470,21 +455,20 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y -CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide/ide.txt for help/info on IDE drives # -CONFIG_IDE_ATAPI=y # CONFIG_BLK_DEV_IDE_SATA is not set -CONFIG_BLK_DEV_IDEDISK=y -# CONFIG_IDEDISK_MULTI_MODE is not set +CONFIG_IDE_GD=y +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set CONFIG_BLK_DEV_IDECD=y CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y # CONFIG_BLK_DEV_IDETAPE is not set -CONFIG_BLK_DEV_IDEFLOPPY=m # CONFIG_BLK_DEV_IDESCSI is not set # CONFIG_IDE_TASK_IOCTL is not set CONFIG_IDE_PROC_FS=y @@ -609,8 +593,12 @@ CONFIG_APNE=m # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_CS89x0 is not set # CONFIG_NET_POCKET is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -763,11 +751,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -777,6 +765,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -802,6 +791,7 @@ CONFIG_SSB_POSSIBLE=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y @@ -829,6 +819,8 @@ CONFIG_FB_FM2=y # CONFIG_FB_UVESA is not set # CONFIG_FB_S1D13XXX is not set # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -852,12 +844,19 @@ CONFIG_LOGO_LINUX_MONO=y CONFIG_LOGO_LINUX_VGA16=y CONFIG_LOGO_LINUX_CLUT224=y CONFIG_SOUND=m +CONFIG_SOUND_OSS_CORE=y CONFIG_DMASOUND_PAULA=m CONFIG_DMASOUND=m CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -867,6 +866,8 @@ CONFIG_HIDRAW=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -883,8 +884,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -895,6 +897,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -906,6 +909,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -944,6 +948,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -986,6 +991,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=m CONFIG_SUNRPC_GSS=m +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=m # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -1059,7 +1065,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -1067,6 +1079,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -1077,10 +1090,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m -CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_AEAD=y +CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1154,14 +1169,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/apollo_defconfig b/arch/m68k/configs/apollo_defconfig index c41b854..935108d 100644 --- a/arch/m68k/configs/apollo_defconfig +++ b/arch/m68k/configs/apollo_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:01 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:43 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set # CONFIG_AMIGA is not set # CONFIG_ATARI is not set # CONFIG_MAC is not set @@ -148,19 +138,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_HEARTBEAT=y @@ -210,7 +202,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -260,13 +251,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -280,19 +272,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -300,20 +295,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -321,8 +316,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -335,9 +330,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -349,16 +344,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -385,6 +380,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -408,19 +404,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -458,6 +443,7 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -540,6 +526,9 @@ CONFIG_NET_ETHERNET=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -609,6 +598,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_VSXXXAA is not set @@ -663,11 +653,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -677,6 +667,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -702,6 +693,7 @@ CONFIG_SSB_POSSIBLE=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y # CONFIG_FB_CFB_COPYAREA is not set CONFIG_FB_CFB_IMAGEBLIT=y @@ -724,6 +716,8 @@ CONFIG_FB_APOLLO=y # CONFIG_FB_UVESA is not set # CONFIG_FB_S1D13XXX is not set # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -750,6 +744,12 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -758,6 +758,8 @@ CONFIG_HIDRAW=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -773,8 +775,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -785,6 +788,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -796,6 +800,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -834,6 +839,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -877,6 +883,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -949,7 +956,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -957,6 +970,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -967,10 +981,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1044,14 +1060,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/atari_defconfig b/arch/m68k/configs/atari_defconfig index 654c5ac..a594a1d 100644 --- a/arch/m68k/configs/atari_defconfig +++ b/arch/m68k/configs/atari_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:02 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:44 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set # CONFIG_AMIGA is not set CONFIG_ATARI=y # CONFIG_MAC is not set @@ -148,19 +138,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_STRAM_PROC=y @@ -208,7 +200,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -258,13 +249,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -278,19 +270,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -298,20 +293,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -319,8 +314,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -333,9 +328,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -347,16 +342,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -383,6 +378,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -406,19 +402,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -462,21 +447,20 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y -CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide/ide.txt for help/info on IDE drives # -CONFIG_IDE_ATAPI=y # CONFIG_BLK_DEV_IDE_SATA is not set -CONFIG_BLK_DEV_IDEDISK=y -# CONFIG_IDEDISK_MULTI_MODE is not set +CONFIG_IDE_GD=y +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set CONFIG_BLK_DEV_IDECD=y CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y # CONFIG_BLK_DEV_IDETAPE is not set -CONFIG_BLK_DEV_IDEFLOPPY=m # CONFIG_BLK_DEV_IDESCSI is not set # CONFIG_IDE_TASK_IOCTL is not set CONFIG_IDE_PROC_FS=y @@ -565,12 +549,15 @@ CONFIG_EQUALIZER=m CONFIG_VETH=m # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y -CONFIG_MII=m +CONFIG_MII=y CONFIG_ATARILANCE=m # CONFIG_IBM_NEW_EMAC_ZMII is not set # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NET_POCKET is not set # CONFIG_NETDEV_1000 is not set @@ -644,6 +631,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set # CONFIG_MOUSE_SERIAL is not set CONFIG_MOUSE_ATARI=m @@ -706,11 +694,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -720,6 +708,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -745,6 +734,7 @@ CONFIG_SSB_POSSIBLE=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y @@ -768,6 +758,8 @@ CONFIG_FB_ATARI=y # CONFIG_FB_S1D13XXX is not set # CONFIG_FB_ATY is not set # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -790,12 +782,19 @@ CONFIG_LOGO_LINUX_MONO=y CONFIG_LOGO_LINUX_VGA16=y CONFIG_LOGO_LINUX_CLUT224=y CONFIG_SOUND=m +CONFIG_SOUND_OSS_CORE=y CONFIG_DMASOUND_ATARI=m CONFIG_DMASOUND=m CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -805,6 +804,8 @@ CONFIG_HIDRAW=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -821,10 +822,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -CONFIG_EXT4DEV_FS=y -# CONFIG_EXT4DEV_FS_XATTR is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y -CONFIG_JBD2=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -835,6 +835,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -846,6 +847,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -884,6 +886,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -925,6 +928,7 @@ CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=m +# CONFIG_SUNRPC_REGISTER_V4 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -998,7 +1002,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -1006,6 +1016,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -1016,10 +1027,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m -CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_AEAD=y +CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1093,14 +1106,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=y CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/bvme6000_defconfig b/arch/m68k/configs/bvme6000_defconfig index 2e44af0..d3d9814 100644 --- a/arch/m68k/configs/bvme6000_defconfig +++ b/arch/m68k/configs/bvme6000_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:03 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:45 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set # CONFIG_AMIGA is not set # CONFIG_ATARI is not set # CONFIG_MAC is not set @@ -151,19 +141,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_PROC_HARDWARE=y @@ -212,7 +204,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -262,13 +253,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -282,19 +274,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -302,20 +297,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -323,8 +318,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -337,9 +332,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -351,16 +346,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -387,6 +382,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -410,19 +406,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -460,6 +445,7 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -545,6 +531,9 @@ CONFIG_BVME6000_NET=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -614,6 +603,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_VSXXXAA is not set @@ -668,11 +658,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -682,6 +672,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -721,6 +712,12 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -729,6 +726,8 @@ CONFIG_HIDRAW=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -744,8 +743,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -756,6 +756,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -767,6 +768,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -805,6 +807,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -848,6 +851,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -921,7 +925,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -929,6 +939,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -939,10 +950,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1016,14 +1029,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=m -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/hp300_defconfig b/arch/m68k/configs/hp300_defconfig index 3570fc8..5556ef0 100644 --- a/arch/m68k/configs/hp300_defconfig +++ b/arch/m68k/configs/hp300_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:04 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:46 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set # CONFIG_AMIGA is not set # CONFIG_ATARI is not set # CONFIG_MAC is not set @@ -149,19 +139,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_HEARTBEAT=y @@ -211,7 +203,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -261,13 +252,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -281,19 +273,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -301,20 +296,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -322,8 +317,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -336,9 +331,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -350,16 +345,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -386,6 +381,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -409,19 +405,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -459,6 +444,7 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -542,6 +528,9 @@ CONFIG_HPLANCE=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -613,6 +602,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_VSXXXAA is not set @@ -673,11 +663,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -687,6 +677,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -712,6 +703,7 @@ CONFIG_SSB_POSSIBLE=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set # CONFIG_FB_CFB_FILLRECT is not set # CONFIG_FB_CFB_COPYAREA is not set CONFIG_FB_CFB_IMAGEBLIT=y @@ -734,6 +726,8 @@ CONFIG_FB_HP300=y # CONFIG_FB_UVESA is not set # CONFIG_FB_S1D13XXX is not set # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -760,6 +754,12 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -768,6 +768,8 @@ CONFIG_HIDRAW=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -781,8 +783,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -793,6 +796,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -804,6 +808,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -842,6 +847,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -885,6 +891,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -957,7 +964,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -965,6 +978,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -975,10 +989,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1052,14 +1068,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/mac_defconfig b/arch/m68k/configs/mac_defconfig index db6e882..c6de257 100644 --- a/arch/m68k/configs/mac_defconfig +++ b/arch/m68k/configs/mac_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:06 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:47 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set # CONFIG_AMIGA is not set # CONFIG_ATARI is not set CONFIG_MAC=y @@ -150,19 +140,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m # CONFIG_HEARTBEAT is not set @@ -209,7 +201,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -259,13 +250,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -279,19 +271,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -299,20 +294,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -320,8 +315,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -334,9 +329,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -348,16 +343,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -384,6 +379,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -410,19 +406,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -460,21 +445,20 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y -CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide/ide.txt for help/info on IDE drives # -CONFIG_IDE_ATAPI=y # CONFIG_BLK_DEV_IDE_SATA is not set -CONFIG_BLK_DEV_IDEDISK=y -# CONFIG_IDEDISK_MULTI_MODE is not set +CONFIG_IDE_GD=y +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set CONFIG_BLK_DEV_IDECD=y CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y # CONFIG_BLK_DEV_IDETAPE is not set -CONFIG_BLK_DEV_IDEFLOPPY=m # CONFIG_BLK_DEV_IDESCSI is not set # CONFIG_IDE_TASK_IOCTL is not set CONFIG_IDE_PROC_FS=y @@ -581,6 +565,9 @@ CONFIG_MACMACE=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -650,6 +637,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_VSXXXAA is not set @@ -706,11 +694,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -720,6 +708,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -745,6 +734,7 @@ CONFIG_SSB_POSSIBLE=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y @@ -768,6 +758,8 @@ CONFIG_FB_MAC=y # CONFIG_FB_UVESA is not set # CONFIG_FB_S1D13XXX is not set # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -796,6 +788,12 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -804,6 +802,8 @@ CONFIG_HIDRAW=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -820,8 +820,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -832,6 +833,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -843,6 +845,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -881,6 +884,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -923,6 +927,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=m CONFIG_SUNRPC_GSS=m +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=m # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -996,7 +1001,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -1004,6 +1015,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -1014,10 +1026,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m -CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_AEAD=y +CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1091,14 +1105,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/multi_defconfig b/arch/m68k/configs/multi_defconfig index 1a80610..7069358 100644 --- a/arch/m68k/configs/multi_defconfig +++ b/arch/m68k/configs/multi_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:07 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:48 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set CONFIG_AMIGA=y CONFIG_ATARI=y CONFIG_MAC=y @@ -154,19 +144,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_ZORRO=y @@ -222,7 +214,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -272,13 +263,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -292,19 +284,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -312,20 +307,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -333,8 +328,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -347,9 +342,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -361,16 +356,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -397,6 +392,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -424,19 +420,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -486,21 +471,20 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y -CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide/ide.txt for help/info on IDE drives # -CONFIG_IDE_ATAPI=y # CONFIG_BLK_DEV_IDE_SATA is not set -CONFIG_BLK_DEV_IDEDISK=y -# CONFIG_IDEDISK_MULTI_MODE is not set +CONFIG_IDE_GD=y +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set CONFIG_BLK_DEV_IDECD=y CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y # CONFIG_BLK_DEV_IDETAPE is not set -CONFIG_BLK_DEV_IDEFLOPPY=m # CONFIG_BLK_DEV_IDESCSI is not set # CONFIG_IDE_TASK_IOCTL is not set CONFIG_IDE_PROC_FS=y @@ -629,7 +613,7 @@ CONFIG_VETH=m # CONFIG_ARCNET is not set # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y -CONFIG_MII=m +CONFIG_MII=y CONFIG_ARIADNE=m CONFIG_A2065=m CONFIG_HYDRA=m @@ -657,8 +641,12 @@ CONFIG_NE2000=m # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_CS89x0 is not set # CONFIG_NET_POCKET is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -735,6 +723,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_INPORT is not set @@ -832,11 +821,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -846,6 +835,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -871,6 +861,7 @@ CONFIG_SSB_POSSIBLE=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y @@ -905,6 +896,8 @@ CONFIG_FB_HP300=y # CONFIG_FB_S1D13XXX is not set # CONFIG_FB_ATY is not set # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -930,6 +923,7 @@ CONFIG_LOGO_LINUX_VGA16=y CONFIG_LOGO_LINUX_CLUT224=y CONFIG_LOGO_MAC_CLUT224=y CONFIG_SOUND=m +CONFIG_SOUND_OSS_CORE=y CONFIG_DMASOUND_ATARI=m CONFIG_DMASOUND_PAULA=m CONFIG_DMASOUND_Q40=m @@ -938,6 +932,12 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -947,6 +947,8 @@ CONFIG_HIDRAW=y # CONFIG_DMADEVICES is not set # CONFIG_AUXDISPLAY is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -973,10 +975,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -CONFIG_EXT4DEV_FS=y -# CONFIG_EXT4DEV_FS_XATTR is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y -CONFIG_JBD2=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -987,6 +988,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -998,6 +1000,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -1036,6 +1039,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -1079,6 +1083,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -1156,7 +1161,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -1164,6 +1175,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -1174,10 +1186,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1251,14 +1265,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=y CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/mvme147_defconfig b/arch/m68k/configs/mvme147_defconfig index cacb5ae..52d4271 100644 --- a/arch/m68k/configs/mvme147_defconfig +++ b/arch/m68k/configs/mvme147_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:08 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:50 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set # CONFIG_AMIGA is not set # CONFIG_ATARI is not set # CONFIG_MAC is not set @@ -151,19 +141,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_PROC_HARDWARE=y @@ -212,7 +204,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -262,13 +253,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -282,19 +274,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -302,20 +297,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -323,8 +318,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -337,9 +332,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -351,16 +346,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -387,6 +382,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -410,19 +406,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -460,6 +445,7 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -544,6 +530,9 @@ CONFIG_MVME147_NET=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -613,6 +602,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_VSXXXAA is not set @@ -667,11 +657,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -681,6 +671,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -720,6 +711,12 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -728,6 +725,8 @@ CONFIG_HIDRAW=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -743,8 +742,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -755,6 +755,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -766,6 +767,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -804,6 +806,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -847,6 +850,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -920,7 +924,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -928,6 +938,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -938,10 +949,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1015,14 +1028,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/mvme16x_defconfig b/arch/m68k/configs/mvme16x_defconfig index a183e25..3403ed2 100644 --- a/arch/m68k/configs/mvme16x_defconfig +++ b/arch/m68k/configs/mvme16x_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:09 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:51 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set # CONFIG_AMIGA is not set # CONFIG_ATARI is not set # CONFIG_MAC is not set @@ -151,19 +141,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_PROC_HARDWARE=y @@ -212,7 +204,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -262,13 +253,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -282,19 +274,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -302,20 +297,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -323,8 +318,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -337,9 +332,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -351,16 +346,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -387,6 +382,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -410,19 +406,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -460,6 +445,7 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -545,6 +531,9 @@ CONFIG_MVME16x_NET=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -614,6 +603,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_VSXXXAA is not set @@ -668,11 +658,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -682,6 +672,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -721,6 +712,12 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -729,6 +726,8 @@ CONFIG_HIDRAW=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -745,8 +744,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -757,6 +757,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -768,6 +769,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -806,6 +808,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -849,6 +852,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -922,7 +926,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -930,6 +940,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -940,10 +951,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1017,14 +1030,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/q40_defconfig b/arch/m68k/configs/q40_defconfig index 72eaff0..3459c59 100644 --- a/arch/m68k/configs/q40_defconfig +++ b/arch/m68k/configs/q40_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:10 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:52 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set # CONFIG_AMIGA is not set # CONFIG_ATARI is not set # CONFIG_MAC is not set @@ -148,19 +138,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_HEARTBEAT=y @@ -209,7 +201,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -259,13 +250,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -279,19 +271,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -299,20 +294,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -320,8 +315,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -334,9 +329,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -348,16 +343,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -384,6 +379,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -407,19 +403,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -458,21 +443,20 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y -CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide/ide.txt for help/info on IDE drives # -CONFIG_IDE_ATAPI=y # CONFIG_BLK_DEV_IDE_SATA is not set -CONFIG_BLK_DEV_IDEDISK=y -# CONFIG_IDEDISK_MULTI_MODE is not set +CONFIG_IDE_GD=y +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set CONFIG_BLK_DEV_IDECD=y CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y # CONFIG_BLK_DEV_IDETAPE is not set -CONFIG_BLK_DEV_IDEFLOPPY=m # CONFIG_BLK_DEV_IDESCSI is not set # CONFIG_IDE_TASK_IOCTL is not set CONFIG_IDE_PROC_FS=y @@ -585,8 +569,12 @@ CONFIG_NE2000=m # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set # CONFIG_B44 is not set +# CONFIG_CS89x0 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set # CONFIG_TR is not set @@ -656,6 +644,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_INPORT is not set @@ -717,11 +706,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -731,6 +720,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -756,6 +746,7 @@ CONFIG_SSB_POSSIBLE=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y @@ -778,6 +769,8 @@ CONFIG_FB_Q40=y # CONFIG_FB_UVESA is not set # CONFIG_FB_S1D13XXX is not set # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -800,12 +793,19 @@ CONFIG_LOGO_LINUX_MONO=y CONFIG_LOGO_LINUX_VGA16=y CONFIG_LOGO_LINUX_CLUT224=y CONFIG_SOUND=m +CONFIG_SOUND_OSS_CORE=y CONFIG_DMASOUND_Q40=m CONFIG_DMASOUND=m CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -814,6 +814,8 @@ CONFIG_HIDRAW=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -827,8 +829,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -839,6 +842,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -850,6 +854,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -888,6 +893,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -930,6 +936,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -1002,7 +1009,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -1010,6 +1023,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -1020,10 +1034,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1097,14 +1113,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/sun3_defconfig b/arch/m68k/configs/sun3_defconfig index cb62b96..f404917 100644 --- a/arch/m68k/configs/sun3_defconfig +++ b/arch/m68k/configs/sun3_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:11 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:53 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y CONFIG_NO_DMA=y -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,10 +105,19 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # +# CONFIG_AMIGA is not set +# CONFIG_ATARI is not set +# CONFIG_MAC is not set +# CONFIG_APOLLO is not set +# CONFIG_VME is not set +# CONFIG_HP300 is not set +# CONFIG_SUN3X is not set +# CONFIG_Q40 is not set CONFIG_SUN3=y # @@ -137,19 +136,21 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_PROC_HARDWARE=y @@ -198,7 +199,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -248,13 +248,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -268,19 +269,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -288,20 +292,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -309,8 +313,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -323,9 +327,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -337,16 +341,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -373,6 +377,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -396,19 +401,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -446,6 +440,7 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -531,6 +526,9 @@ CONFIG_SUN3_82586=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -599,6 +597,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_VSXXXAA is not set @@ -655,16 +654,13 @@ CONFIG_GEN_RTC_X=y # CONFIG_WATCHDOG is not set # -# Sonics Silicon Backplane -# - -# # Multifunction device drivers # # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -690,6 +686,7 @@ CONFIG_GEN_RTC_X=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set # CONFIG_FB_CFB_FILLRECT is not set # CONFIG_FB_CFB_COPYAREA is not set # CONFIG_FB_CFB_IMAGEBLIT is not set @@ -711,6 +708,8 @@ CONFIG_FB=y # CONFIG_FB_UVESA is not set # CONFIG_FB_S1D13XXX is not set # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -737,6 +736,12 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -744,6 +749,8 @@ CONFIG_HIDRAW=y # CONFIG_ACCESSIBILITY is not set # CONFIG_RTC_CLASS is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -757,8 +764,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -769,6 +777,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -780,6 +789,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -818,6 +828,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -861,6 +872,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -934,7 +946,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -942,6 +960,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -952,10 +971,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1029,14 +1050,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=y diff --git a/arch/m68k/configs/sun3x_defconfig b/arch/m68k/configs/sun3x_defconfig index 04b4363..4d8a1e8 100644 --- a/arch/m68k/configs/sun3x_defconfig +++ b/arch/m68k/configs/sun3x_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc6 -# Wed Sep 10 09:02:12 2008 +# Linux kernel version: 2.6.28-rc7 +# Tue Dec 2 20:27:54 2008 # CONFIG_M68K=y CONFIG_MMU=y @@ -14,7 +14,6 @@ CONFIG_TIME_LOW_RES=y CONFIG_GENERIC_IOMAP=y CONFIG_NO_IOPORT=y # CONFIG_NO_DMA is not set -CONFIG_ARCH_SUPPORTS_AOUT=y CONFIG_HZ=100 CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -67,22 +66,13 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set # CONFIG_PROFILING is not set # CONFIG_MARKERS is not set -# CONFIG_HAVE_OPROFILE is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set -# CONFIG_HAVE_KPROBES is not set -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -115,11 +105,11 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Platform dependent setup # -# CONFIG_SUN3 is not set # CONFIG_AMIGA is not set # CONFIG_ATARI is not set # CONFIG_MAC is not set @@ -148,19 +138,21 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # # General setup # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y CONFIG_BINFMT_AOUT=m CONFIG_BINFMT_MISC=m CONFIG_PROC_HARDWARE=y @@ -209,7 +201,6 @@ CONFIG_INET_TCP_DIAG=m CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -259,13 +250,14 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m # CONFIG_NF_CT_NETLINK is not set +# CONFIG_NETFILTER_TPROXY is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m CONFIG_NETFILTER_XT_TARGET_RATEEST=m CONFIG_NETFILTER_XT_TARGET_TRACE=m @@ -279,19 +271,22 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m +CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_OWNER=m CONFIG_NETFILTER_XT_MATCH_POLICY=m -CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m @@ -299,20 +294,20 @@ CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -320,8 +315,8 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m CONFIG_NF_NAT_PROTO_GRE=m CONFIG_NF_NAT_PROTO_UDPLITE=m @@ -334,9 +329,9 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m @@ -348,16 +343,16 @@ CONFIG_IP_NF_ARP_MANGLE=m CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -384,6 +379,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -407,19 +403,8 @@ CONFIG_NET_CLS_ROUTE=y # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -CONFIG_WIRELESS_EXT=y -# CONFIG_WIRELESS_EXT_SYSFS is not set -# CONFIG_MAC80211 is not set -CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -457,6 +442,7 @@ CONFIG_ATA_OVER_ETH=m CONFIG_MISC_DEVICES=y # CONFIG_EEPROM_93CX6 is not set # CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -541,6 +527,9 @@ CONFIG_SUN3LANCE=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -610,6 +599,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_VSXXXAA is not set @@ -664,11 +654,11 @@ CONFIG_GEN_RTC_X=y # CONFIG_THERMAL is not set # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -678,6 +668,7 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set # CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -703,6 +694,7 @@ CONFIG_SSB_POSSIBLE=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set # CONFIG_FB_CFB_FILLRECT is not set # CONFIG_FB_CFB_COPYAREA is not set # CONFIG_FB_CFB_IMAGEBLIT is not set @@ -724,6 +716,8 @@ CONFIG_FB=y # CONFIG_FB_UVESA is not set # CONFIG_FB_S1D13XXX is not set # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # @@ -750,6 +744,12 @@ CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set CONFIG_HIDRAW=y +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y # CONFIG_USB_SUPPORT is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set @@ -758,6 +758,8 @@ CONFIG_HIDRAW=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # Character devices @@ -771,8 +773,9 @@ CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y +CONFIG_JBD2=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set @@ -783,6 +786,7 @@ CONFIG_JFS_FS=m # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -794,6 +798,7 @@ CONFIG_OCFS2_FS_USERSPACE_CLUSTER=m # CONFIG_OCFS2_FS_STATS is not set # CONFIG_OCFS2_DEBUG_MASKLOG is not set # CONFIG_OCFS2_DEBUG_FS is not set +# CONFIG_OCFS2_COMPAT_JBD is not set CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y @@ -832,6 +837,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -875,6 +881,7 @@ CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=y # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -948,7 +955,13 @@ CONFIG_MAGIC_SYSRQ=y # CONFIG_DEBUG_KERNEL is not set CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -956,6 +969,7 @@ CONFIG_SYSCTL_SYSCALL_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m @@ -966,10 +980,12 @@ CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_GF128MUL=m CONFIG_CRYPTO_NULL=m @@ -1043,14 +1059,17 @@ CONFIG_CRYPTO_TWOFISH_COMMON=m # CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=m CONFIG_CRC_T10DIF=y -- cgit v1.1 From 82676d76252680fc035247fd4cfdb07ffce5db52 Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Thu, 27 Nov 2008 06:21:03 -1100 Subject: [ARM] Orion: fix bug in pcie configuration cycle function field mask The function field is 3 bits. Signed-off-by: Saeed Bishara Signed-off-by: Nicolas Pitre --- arch/arm/plat-orion/pcie.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-orion/pcie.c b/arch/arm/plat-orion/pcie.c index 883902f..d41d41d 100644 --- a/arch/arm/plat-orion/pcie.c +++ b/arch/arm/plat-orion/pcie.c @@ -35,7 +35,7 @@ #define PCIE_CONF_REG(r) ((((r) & 0xf00) << 16) | ((r) & 0xfc)) #define PCIE_CONF_BUS(b) (((b) & 0xff) << 16) #define PCIE_CONF_DEV(d) (((d) & 0x1f) << 11) -#define PCIE_CONF_FUNC(f) (((f) & 0x3) << 8) +#define PCIE_CONF_FUNC(f) (((f) & 0x7) << 8) #define PCIE_CONF_DATA_OFF 0x18fc #define PCIE_MASK_OFF 0x1910 #define PCIE_CTRL_OFF 0x1a00 -- cgit v1.1 From 7a0d7940e7c7c143520e38900ddd4e217d3c6640 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 2 Dec 2008 13:37:01 -0600 Subject: powerpc: Use physical cpu id when setting the processor affinity In the CONFIG_SMP case the irq_choose_cpu() code was returning back a logical cpu id not the physical id. We were writing that directly into the HW register. We need to be calling get_hard_smp_processor_id() so irq_choose_cpu() always returns a physical cpu id. Signed-off-by: Kumar Gala Signed-off-by: Linus Torvalds --- arch/powerpc/sysdev/mpic.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/powerpc/sysdev/mpic.c b/arch/powerpc/sysdev/mpic.c index b24e1d08..1890fb0 100644 --- a/arch/powerpc/sysdev/mpic.c +++ b/arch/powerpc/sysdev/mpic.c @@ -600,7 +600,7 @@ static int irq_choose_cpu(unsigned int virt_irq) cpuid = first_cpu(tmp); } - return cpuid; + return get_hard_smp_processor_id(cpuid); } #else static int irq_choose_cpu(unsigned int virt_irq) -- cgit v1.1 From 1122b19b8f4da2ee6d6b21780f86bea7957f641e Mon Sep 17 00:00:00 2001 From: Mark Salter Date: Tue, 2 Dec 2008 14:38:09 +0000 Subject: MN10300: Fix application of kernel module relocations This fixes the MN10300 kernel module linking to match the toolchain. RELA relocs don't use the value at the location being relocated. This has been working because the tools always leave the value at the target location cleared. Signed-off-by: Mark Salter Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- arch/mn10300/kernel/module.c | 35 +++++++---------------------------- 1 file changed, 7 insertions(+), 28 deletions(-) (limited to 'arch') diff --git a/arch/mn10300/kernel/module.c b/arch/mn10300/kernel/module.c index 8fa3689..6b287f2 100644 --- a/arch/mn10300/kernel/module.c +++ b/arch/mn10300/kernel/module.c @@ -1,6 +1,6 @@ /* MN10300 Kernel module helper routines * - * Copyright (C) 2007 Red Hat, Inc. All Rights Reserved. + * Copyright (C) 2007, 2008 Red Hat, Inc. All Rights Reserved. * Written by Mark Salter (msalter@redhat.com) * - Derived from arch/i386/kernel/module.c * @@ -64,21 +64,6 @@ int module_frob_arch_sections(Elf_Ehdr *hdr, return 0; } -static uint32_t reloc_get16(uint8_t *p) -{ - return p[0] | (p[1] << 8); -} - -static uint32_t reloc_get24(uint8_t *p) -{ - return reloc_get16(p) | (p[2] << 16); -} - -static uint32_t reloc_get32(uint8_t *p) -{ - return reloc_get16(p) | (reloc_get16(p+2) << 16); -} - static void reloc_put16(uint8_t *p, uint32_t val) { p[0] = val & 0xff; @@ -144,25 +129,19 @@ int apply_relocate_add(Elf32_Shdr *sechdrs, relocation = sym->st_value + rel[i].r_addend; switch (ELF32_R_TYPE(rel[i].r_info)) { - /* for the first four relocation types, we add the - * adjustment into the value at the location given */ + /* for the first four relocation types, we simply + * store the adjustment at the location given */ case R_MN10300_32: - value = reloc_get32(location); - value += relocation; - reloc_put32(location, value); + reloc_put32(location, relocation); break; case R_MN10300_24: - value = reloc_get24(location); - value += relocation; - reloc_put24(location, value); + reloc_put24(location, relocation); break; case R_MN10300_16: - value = reloc_get16(location); - value += relocation; - reloc_put16(location, value); + reloc_put16(location, relocation); break; case R_MN10300_8: - *location += relocation; + *location = relocation; break; /* for the next three relocation types, we write the -- cgit v1.1 From 2434bbb30e79468c49cff3cff6005236f55ed188 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Sun, 30 Nov 2008 18:53:40 +0000 Subject: powerpc: Fix dma_map_sg() cache flushing on non coherent platforms On PowerPC 4xx or other non cache-coherent platforms, we lost the appropriate cache flushing in dma_map_sg() when merging the 32 and 64-bit DMA code (commit 4fc665b88a79a45bae8bbf3a05563c27c7337c3d, "powerpc: Merge 32 and 64-bit dma code"). This restores it. Signed-off-by: Benjamin Herrenschmidt Acked-by: Becky Bruce Signed-off-by: Paul Mackerras --- arch/powerpc/kernel/dma.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/powerpc/kernel/dma.c b/arch/powerpc/kernel/dma.c index 1562daf..3a6eaa8 100644 --- a/arch/powerpc/kernel/dma.c +++ b/arch/powerpc/kernel/dma.c @@ -75,6 +75,7 @@ static int dma_direct_map_sg(struct device *dev, struct scatterlist *sgl, for_each_sg(sgl, sg, nents, i) { sg->dma_address = sg_phys(sg) + get_dma_direct_offset(dev); sg->dma_length = sg->length; + __dma_sync_page(sg_page(sg), sg->offset, sg->length, direction); } return nents; -- cgit v1.1 From ee4ee527278a66321301d4f1f5ae22e49ab18fad Mon Sep 17 00:00:00 2001 From: Chris Torek Date: Wed, 3 Dec 2008 00:47:28 -0800 Subject: sparc64: Fix bug in PTRACE_SETFPREGS64 handling. From: Chris Torek >The SPARC64 kernel code for PTRACE_SETFPREGS64 appears to be an exact copy >of that for PTRACE_GETFPREGS64. This means that gdbserver and native >64-bit GDB cannot set floating-point registers. It looks like a simple typo. Signed-off-by: David S. Miller --- arch/sparc64/kernel/ptrace.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/sparc64/kernel/ptrace.c b/arch/sparc64/kernel/ptrace.c index f43adbc..a941c61 100644 --- a/arch/sparc64/kernel/ptrace.c +++ b/arch/sparc64/kernel/ptrace.c @@ -1014,7 +1014,7 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data) break; case PTRACE_SETFPREGS64: - ret = copy_regset_to_user(child, view, REGSET_FP, + ret = copy_regset_from_user(child, view, REGSET_FP, 0 * sizeof(u64), 33 * sizeof(u64), fps); -- cgit v1.1 From 70d7d357578245f1993fd2d3ccd26088bcd38941 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Tue, 2 Dec 2008 20:16:03 +0100 Subject: x86: fix broken flushing in GART nofullflush path Impact: remove stale IOTLB entries In the non-default nofullflush case the GART is only flushed when next_bit wraps around. But it can happen that an unmap operation unmaps memory which is behind the current next_bit location. If these addresses are reused it may result in stale GART IO/TLB entries. Fix this by setting the GART next_bit always behind an unmapped location. Signed-off-by: Joerg Roedel Signed-off-by: Ingo Molnar --- arch/x86/kernel/pci-gart_64.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/x86/kernel/pci-gart_64.c b/arch/x86/kernel/pci-gart_64.c index a42b02b..ba7ad83 100644 --- a/arch/x86/kernel/pci-gart_64.c +++ b/arch/x86/kernel/pci-gart_64.c @@ -123,6 +123,8 @@ static void free_iommu(unsigned long offset, int size) spin_lock_irqsave(&iommu_bitmap_lock, flags); iommu_area_free(iommu_gart_bitmap, offset, size); + if (offset >= next_bit) + next_bit = offset + size; spin_unlock_irqrestore(&iommu_bitmap_lock, flags); } -- cgit v1.1 From eac9fbc6a90ab3440f4d98a8c52b15a724fc6f4f Mon Sep 17 00:00:00 2001 From: Richard Kennedy Date: Mon, 24 Nov 2008 13:53:24 +0000 Subject: AMD IOMMU: struct amd_iommu remove padding on 64 bit Remove 16 bytes of padding from struct amd_iommu on 64bit builds reducing its size to 120 bytes, allowing it to span one fewer cachelines. Signed-off-by: Richard Kennedy Signed-off-by: Joerg Roedel --- arch/x86/include/asm/amd_iommu_types.h | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) (limited to 'arch') diff --git a/arch/x86/include/asm/amd_iommu_types.h b/arch/x86/include/asm/amd_iommu_types.h index 1a30c04..ac302a2 100644 --- a/arch/x86/include/asm/amd_iommu_types.h +++ b/arch/x86/include/asm/amd_iommu_types.h @@ -251,13 +251,6 @@ struct amd_iommu { /* Pointer to PCI device of this IOMMU */ struct pci_dev *dev; - /* - * Capability pointer. There could be more than one IOMMU per PCI - * device function if there are more than one AMD IOMMU capability - * pointers. - */ - u16 cap_ptr; - /* physical address of MMIO space */ u64 mmio_phys; /* virtual address of MMIO space */ @@ -266,6 +259,13 @@ struct amd_iommu { /* capabilities of that IOMMU read from ACPI */ u32 cap; + /* + * Capability pointer. There could be more than one IOMMU per PCI + * device function if there are more than one AMD IOMMU capability + * pointers. + */ + u16 cap_ptr; + /* pci domain of this IOMMU */ u16 pci_seg; @@ -284,19 +284,19 @@ struct amd_iommu { /* size of command buffer */ u32 cmd_buf_size; - /* event buffer virtual address */ - u8 *evt_buf; /* size of event buffer */ u32 evt_buf_size; + /* event buffer virtual address */ + u8 *evt_buf; /* MSI number for event interrupt */ u16 evt_msi_num; - /* if one, we need to send a completion wait command */ - int need_sync; - /* true if interrupts for this IOMMU are already enabled */ bool int_enabled; + /* if one, we need to send a completion wait command */ + int need_sync; + /* default dma_ops domain for that IOMMU */ struct dma_ops_domain *default_dom; }; -- cgit v1.1 From f91ba190648be4ff127d6aaf3993ac19d66dc2c2 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Tue, 25 Nov 2008 12:56:12 +0100 Subject: AMD IOMMU: set device table entry for aliased devices In some rare cases a request can arrive an IOMMU with its originial requestor id even it is aliased. Handle this by setting the device table entry to the same protection domain for the original and the aliased requestor id. Signed-off-by: Joerg Roedel --- arch/x86/kernel/amd_iommu.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index e4899e0..a232e5a 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -858,6 +858,9 @@ static int get_device_resources(struct device *dev, print_devid(_bdf, 1); } + if (domain_for_device(_bdf) == NULL) + set_device_domain(*iommu, *domain, _bdf); + return 1; } -- cgit v1.1 From 09ee17eb8ea89514c13980c4010bdbbaea8630c2 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Wed, 3 Dec 2008 12:19:27 +0100 Subject: AMD IOMMU: fix possible race while accessing iommu->need_sync The access to the iommu->need_sync member needs to be protected by the iommu->lock. Otherwise this is a possible race condition. Fix it with this patch. Signed-off-by: Joerg Roedel --- arch/x86/kernel/amd_iommu.c | 33 +++++++++++++-------------------- 1 file changed, 13 insertions(+), 20 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index a232e5a..5662e22 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -187,6 +187,8 @@ static int iommu_queue_command(struct amd_iommu *iommu, struct iommu_cmd *cmd) spin_lock_irqsave(&iommu->lock, flags); ret = __iommu_queue_command(iommu, cmd); + if (!ret) + iommu->need_sync = 1; spin_unlock_irqrestore(&iommu->lock, flags); return ret; @@ -210,10 +212,13 @@ static int iommu_completion_wait(struct amd_iommu *iommu) cmd.data[0] = CMD_COMPL_WAIT_INT_MASK; CMD_SET_TYPE(&cmd, CMD_COMPL_WAIT); - iommu->need_sync = 0; - spin_lock_irqsave(&iommu->lock, flags); + if (!iommu->need_sync) + goto out; + + iommu->need_sync = 0; + ret = __iommu_queue_command(iommu, &cmd); if (ret) @@ -254,8 +259,6 @@ static int iommu_queue_inv_dev_entry(struct amd_iommu *iommu, u16 devid) ret = iommu_queue_command(iommu, &cmd); - iommu->need_sync = 1; - return ret; } @@ -281,8 +284,6 @@ static int iommu_queue_inv_iommu_pages(struct amd_iommu *iommu, ret = iommu_queue_command(iommu, &cmd); - iommu->need_sync = 1; - return ret; } @@ -762,8 +763,6 @@ static void set_device_domain(struct amd_iommu *iommu, write_unlock_irqrestore(&amd_iommu_devtable_lock, flags); iommu_queue_inv_dev_entry(iommu, devid); - - iommu->need_sync = 1; } /***************************************************************************** @@ -1034,8 +1033,7 @@ static dma_addr_t map_single(struct device *dev, phys_addr_t paddr, if (addr == bad_dma_address) goto out; - if (unlikely(iommu->need_sync)) - iommu_completion_wait(iommu); + iommu_completion_wait(iommu); out: spin_unlock_irqrestore(&domain->lock, flags); @@ -1063,8 +1061,7 @@ static void unmap_single(struct device *dev, dma_addr_t dma_addr, __unmap_single(iommu, domain->priv, dma_addr, size, dir); - if (unlikely(iommu->need_sync)) - iommu_completion_wait(iommu); + iommu_completion_wait(iommu); spin_unlock_irqrestore(&domain->lock, flags); } @@ -1130,8 +1127,7 @@ static int map_sg(struct device *dev, struct scatterlist *sglist, goto unmap; } - if (unlikely(iommu->need_sync)) - iommu_completion_wait(iommu); + iommu_completion_wait(iommu); out: spin_unlock_irqrestore(&domain->lock, flags); @@ -1176,8 +1172,7 @@ static void unmap_sg(struct device *dev, struct scatterlist *sglist, s->dma_address = s->dma_length = 0; } - if (unlikely(iommu->need_sync)) - iommu_completion_wait(iommu); + iommu_completion_wait(iommu); spin_unlock_irqrestore(&domain->lock, flags); } @@ -1228,8 +1223,7 @@ static void *alloc_coherent(struct device *dev, size_t size, goto out; } - if (unlikely(iommu->need_sync)) - iommu_completion_wait(iommu); + iommu_completion_wait(iommu); out: spin_unlock_irqrestore(&domain->lock, flags); @@ -1260,8 +1254,7 @@ static void free_coherent(struct device *dev, size_t size, __unmap_single(iommu, domain->priv, dma_addr, size, DMA_BIDIRECTIONAL); - if (unlikely(iommu->need_sync)) - iommu_completion_wait(iommu); + iommu_completion_wait(iommu); spin_unlock_irqrestore(&domain->lock, flags); -- cgit v1.1 From 9ea84ad77d635bdb76c9a08f44f21a9af98359ee Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Tue, 2 Dec 2008 07:21:21 +0100 Subject: oprofile: fix CPU unplug panic in ppro_stop() If oprofile statically compiled in kernel, a cpu unplug triggers a panic in ppro_stop(), because a NULL pointer is dereferenced. Signed-off-by: Eric Dumazet Signed-off-by: Robert Richter --- arch/x86/oprofile/op_model_ppro.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch') diff --git a/arch/x86/oprofile/op_model_ppro.c b/arch/x86/oprofile/op_model_ppro.c index 716d26f..e9f80c7 100644 --- a/arch/x86/oprofile/op_model_ppro.c +++ b/arch/x86/oprofile/op_model_ppro.c @@ -156,6 +156,8 @@ static void ppro_start(struct op_msrs const * const msrs) unsigned int low, high; int i; + if (!reset_value) + return; for (i = 0; i < num_counters; ++i) { if (reset_value[i]) { CTRL_READ(low, high, msrs, i); @@ -171,6 +173,8 @@ static void ppro_stop(struct op_msrs const * const msrs) unsigned int low, high; int i; + if (!reset_value) + return; for (i = 0; i < num_counters; ++i) { if (!reset_value[i]) continue; -- cgit v1.1 From dafdb61313e80e20cfeef7bf4653dcb47cf28591 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 27 Nov 2008 20:36:45 +0300 Subject: powerpc/83xx: Fix MCU support merge issue in mpc8349emitx.dts Just found the merge issue in 442746989d92afc125040e0f29b33602ad94da99 ("powerpc/83xx: Add support for MCU microcontroller in .dts files"): the commit adds the MCU controller node into the DMA node, which is wrong because the MCU sits on the I2C bus. Fix this by moving the MCU node into the I2C controller node. The original patch[1] was OK though. ;-) Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8349emitx.dts | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/boot/dts/mpc8349emitx.dts b/arch/powerpc/boot/dts/mpc8349emitx.dts index 2c9d54a..4bdbaf4 100644 --- a/arch/powerpc/boot/dts/mpc8349emitx.dts +++ b/arch/powerpc/boot/dts/mpc8349emitx.dts @@ -91,6 +91,14 @@ interrupts = <18 0x8>; interrupt-parent = <&ipic>; }; + + mcu_pio: mcu@a { + #gpio-cells = <2>; + compatible = "fsl,mc9s08qg8-mpc8349emitx", + "fsl,mcu-mpc8349emitx"; + reg = <0x0a>; + gpio-controller; + }; }; spi@7000 { @@ -139,14 +147,6 @@ interrupt-parent = <&ipic>; interrupts = <71 8>; }; - - mcu_pio: mcu@a { - #gpio-cells = <2>; - compatible = "fsl,mc9s08qg8-mpc8349emitx", - "fsl,mcu-mpc8349emitx"; - reg = <0x0a>; - gpio-controller; - }; }; usb@22000 { -- cgit v1.1 From 3d337c653c94be50f11a45fb14a2afa8a8a1a618 Mon Sep 17 00:00:00 2001 From: William Cohen Date: Sun, 30 Nov 2008 15:39:10 -0500 Subject: x86/oprofile: fix Intel cpu family 6 detection Alan Jenkins wrote: > This is on an EeePC 701, /proc/cpuinfo as attached. > > Is this expected? Will the next release work? > > Thanks, Alan > > # opcontrol --setup --no-vmlinux > cpu_type 'unset' is not valid > you should upgrade oprofile or force the use of timer mode > > # opcontrol -v > opcontrol: oprofile 0.9.4 compiled on Nov 29 2008 22:44:10 > > # cat /dev/oprofile/cpu_type > i386/p6 > # uname -r > 2.6.28-rc6eeepc Hi Alan, Looking at the kernel driver code for oprofile it can return the "i386/p6" for the cpu_type. However, looking at the user-space oprofile code there isn't the matching entry in libop/op_cpu_type.c or the events/unit_mask files in events/i386 directory. The Intel AP-485 says this is a "Intel Pentium M processor model D". Seems like the oprofile kernel driver should be identifying the processor as "i386/p6_mobile" The driver identification code doesn't look quite right in nmi_init.c http://git.kernel.org/?p=linux/kernel/git/sfr/linux-next.git;a=blob;f=arch/x86/oprofile/nmi_int.c;h=022cd41ea9b4106e5884277096e80e9088a7c7a9;hb=HEAD has: 409 case 10 ... 13: 410 *cpu_type = "i386/p6"; 411 break; Referring to the Intel AP-485: case 10 and 11 should produce "i386/piii" case 13 should produce "i386/p6_mobile" I didn't see anything for case 12. Something like the attached patch. I don't have a celeron machine to verify that changes in this area of the kernel fix thing. -Will Signed-off-by: William Cohen Tested-by: Alan Jenkins Acked-by: Andi Kleen Signed-off-by: Robert Richter --- arch/x86/oprofile/nmi_int.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/x86/oprofile/nmi_int.c b/arch/x86/oprofile/nmi_int.c index 022cd41..202864a 100644 --- a/arch/x86/oprofile/nmi_int.c +++ b/arch/x86/oprofile/nmi_int.c @@ -401,14 +401,13 @@ static int __init ppro_init(char **cpu_type) *cpu_type = "i386/pii"; break; case 6 ... 8: + case 10 ... 11: *cpu_type = "i386/piii"; break; case 9: + case 13: *cpu_type = "i386/p6_mobile"; break; - case 10 ... 13: - *cpu_type = "i386/p6"; - break; case 14: *cpu_type = "i386/core"; break; -- cgit v1.1 From e8e8e80ee047b131a0cd6a3e96e0f8dfa14f6d99 Mon Sep 17 00:00:00 2001 From: Rusty Russell Date: Wed, 3 Dec 2008 16:04:52 -0800 Subject: sparc: asm/bitops.h should define __fls bitops_64.h includes the generic one; pretty sure 32 should too. (Found by using __fls in generic code and breaking sparc defconfig build: thanks Stephen and linux-next!) Signed-off-by: Rusty Russell Signed-off-by: David S. Miller --- arch/sparc/include/asm/bitops_32.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/sparc/include/asm/bitops_32.h b/arch/sparc/include/asm/bitops_32.h index 68b98a7e..9cf4ae0 100644 --- a/arch/sparc/include/asm/bitops_32.h +++ b/arch/sparc/include/asm/bitops_32.h @@ -98,6 +98,7 @@ static inline void change_bit(unsigned long nr, volatile unsigned long *addr) #include #include #include +#include #include #include #include -- cgit v1.1 From 004b50f4ed2accb56069d56714a32484f8b83ec0 Mon Sep 17 00:00:00 2001 From: David Howells Date: Wed, 3 Dec 2008 16:33:14 +0000 Subject: MN10300: Introduce barriers to replace removed volatiles in gdbstub 16550 driver Introduce into the MN10300 gdbstub 16550 driver a couple of barrier() calls to replace the removed volatility of the input/output index variables for the Rx ring buffer. A previous patch added them into the on-chip serial port driver. Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- arch/mn10300/kernel/gdb-io-serial.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/mn10300/kernel/gdb-io-serial.c b/arch/mn10300/kernel/gdb-io-serial.c index 9a6d4e8..11584c5 100644 --- a/arch/mn10300/kernel/gdb-io-serial.c +++ b/arch/mn10300/kernel/gdb-io-serial.c @@ -99,6 +99,7 @@ int gdbstub_io_rx_char(unsigned char *_ch, int nonblock) try_again: /* pull chars out of the buffer */ ix = gdbstub_rx_outp; + barrier(); if (ix == gdbstub_rx_inp) { if (nonblock) return -EAGAIN; @@ -110,6 +111,7 @@ int gdbstub_io_rx_char(unsigned char *_ch, int nonblock) ch = gdbstub_rx_buffer[ix++]; st = gdbstub_rx_buffer[ix++]; + barrier(); gdbstub_rx_outp = ix & 0x00000fff; if (st & UART_LSR_BI) { -- cgit v1.1 From 726c12f57d7e3ff43693d88e13b1ff02464c75d3 Mon Sep 17 00:00:00 2001 From: Joseph Myers Date: Wed, 3 Dec 2008 19:36:05 -0800 Subject: sparc64: Fix VIS emulation bugs This patch fixes some bugs in VIS emulation that cause the GCC test failure FAIL: gcc.target/sparc/pdist-3.c execution test for both 32-bit and 64-bit testing on hardware lacking these instructions. The emulation code for the pdist instruction uses RS1(insn) for both source registers rs1 and rs2, which is obviously wrong and leads to the instruction doing nothing (the observed problem), and further inspection of the code shows that RS1 uses a shift of 24 and RD a shift of 25, which clearly cannot both be right; examining SPARC documentation indicates the correct shift for RS1 is 14. This patch fixes the bug if single-stepping over the affected instruction in the debugger, but not if the testcase is run standalone. For that, Wind River has another patch I hope they will send as a followup to this patch submission. Signed-off-by: Joseph Myers Signed-off-by: David S. Miller --- arch/sparc64/kernel/visemul.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/sparc64/kernel/visemul.c b/arch/sparc64/kernel/visemul.c index 9e05cb5..69f8a35 100644 --- a/arch/sparc64/kernel/visemul.c +++ b/arch/sparc64/kernel/visemul.c @@ -131,7 +131,7 @@ #define VIS_OPF_SHIFT 5 #define VIS_OPF_MASK (0x1ff << VIS_OPF_SHIFT) -#define RS1(INSN) (((INSN) >> 24) & 0x1f) +#define RS1(INSN) (((INSN) >> 14) & 0x1f) #define RS2(INSN) (((INSN) >> 0) & 0x1f) #define RD(INSN) (((INSN) >> 25) & 0x1f) @@ -445,7 +445,7 @@ static void pdist(struct pt_regs *regs, unsigned int insn) unsigned long i; rs1 = fpd_regval(f, RS1(insn)); - rs2 = fpd_regval(f, RS1(insn)); + rs2 = fpd_regval(f, RS2(insn)); rd = fpd_regaddr(f, RD(insn)); rd_val = *rd; -- cgit v1.1 From 94fc7336646b392234c0fafea5d696d020c3677c Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Thu, 4 Dec 2008 03:59:41 +0100 Subject: [ARM] 5339/1: fix __fls() on ARM Commit 0c65f459ce6c intended to fix truncation issues with fls() on ARMv5+ by renaming it to __fls() and wrapping it into a C function. However that didn't take into account the fact that __fls() already already had different semantics in the kernel. Let's move the __fls() code into fls() function directly, and redefine __fls() with the appropriate semantics. While at it, bring a generic __fls() definition for pre ARMv5 too. Signed-off-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/include/asm/bitops.h | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/arm/include/asm/bitops.h b/arch/arm/include/asm/bitops.h index 9a1db20..63a481f 100644 --- a/arch/arm/include/asm/bitops.h +++ b/arch/arm/include/asm/bitops.h @@ -237,6 +237,7 @@ extern int _find_next_bit_be(const unsigned long *p, int size, int offset); #if __LINUX_ARM_ARCH__ < 5 #include +#include #include #include #include @@ -277,16 +278,19 @@ static inline int constant_fls(int x) * the clz instruction for much better code efficiency. */ -#define __fls(x) \ - ( __builtin_constant_p(x) ? constant_fls(x) : \ - ({ int __r; asm("clz\t%0, %1" : "=r"(__r) : "r"(x) : "cc"); 32-__r; }) ) - -/* Implement fls() in C so that 64-bit args are suitably truncated */ static inline int fls(int x) { - return __fls(x); + int ret; + + if (__builtin_constant_p(x)) + return constant_fls(x); + + asm("clz\t%0, %1" : "=r" (ret) : "r" (x) : "cc"); + ret = 32 - ret; + return ret; } +#define __fls(x) (fls(x) - 1) #define ffs(x) ({ unsigned long __t = (x); fls(__t & -__t); }) #define __ffs(x) (ffs(x) - 1) #define ffz(x) __ffs( ~(x) ) -- cgit v1.1 From 9adc13867ec5fe0cd35434f92954d90e42381f0b Mon Sep 17 00:00:00 2001 From: Andi Kleen Date: Thu, 4 Dec 2008 13:33:35 +0100 Subject: x86: fix early panic with boot option "nosmp" Impact: fix boot crash with numcpus=0 on certain systems Fix early exception in __get_smp_config with nosmp. Bail out early when there is no MP table. Reported-by: Wu Fengguang Signed-off-by: Andi Kleen Tested-by: Wu Fengguang Signed-off-by: Ingo Molnar --- arch/x86/kernel/mpparse.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/x86/kernel/mpparse.c b/arch/x86/kernel/mpparse.c index f98f4e1..0f4c1fd 100644 --- a/arch/x86/kernel/mpparse.c +++ b/arch/x86/kernel/mpparse.c @@ -604,6 +604,9 @@ static void __init __get_smp_config(unsigned int early) printk(KERN_INFO "Using ACPI for processor (LAPIC) " "configuration information\n"); + if (!mpf) + return; + printk(KERN_INFO "Intel MultiProcessor Specification v1.%d\n", mpf->mpf_specification); #if defined(CONFIG_X86_LOCAL_APIC) && defined(CONFIG_X86_32) -- cgit v1.1 From 410d2c8187ed969238ba98008c1d57307a56cfd8 Mon Sep 17 00:00:00 2001 From: "Hong H. Pham" Date: Thu, 4 Dec 2008 09:12:57 -0800 Subject: sparc64: Sync FPU state in VIS emulation handler. Copy the FPU state to the task's thread_info->fpregs for the VIS emulation functions to access. Signed-off-by: Hong H. Pham Signed-off-by: David S. Miller --- arch/sparc64/kernel/visemul.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/sparc64/kernel/visemul.c b/arch/sparc64/kernel/visemul.c index 69f8a35..b956fd7 100644 --- a/arch/sparc64/kernel/visemul.c +++ b/arch/sparc64/kernel/visemul.c @@ -807,6 +807,8 @@ int vis_emul(struct pt_regs *regs, unsigned int insn) if (get_user(insn, (u32 __user *) pc)) return -EFAULT; + save_and_clear_fpu(); + opf = (insn & VIS_OPF_MASK) >> VIS_OPF_SHIFT; switch (opf) { default: -- cgit v1.1 From e807f9574e37a3f202e677feaaad1b7c5d2c0db8 Mon Sep 17 00:00:00 2001 From: Vlad Malov Date: Tue, 18 Nov 2008 15:05:46 -0800 Subject: MIPS: Fix potential DOS by untrusted user app. On a 64 bit kernel if an o32 syscall was made with a syscall number less than 4000, we would read the function from outside of the bounds of the syscall table. This led to non-deterministic behavior including system crashes. While we were at it we reworked the 32 bit version as well to use fewer instructions. Both 32 and 64 bit versions are use the same code now. Signed-off-by: Vlad Malov Signed-off-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/kernel/scall32-o32.S | 5 +---- arch/mips/kernel/scall64-o32.S | 12 +++++------- 2 files changed, 6 insertions(+), 11 deletions(-) (limited to 'arch') diff --git a/arch/mips/kernel/scall32-o32.S b/arch/mips/kernel/scall32-o32.S index 759f680..34a4dbd 100644 --- a/arch/mips/kernel/scall32-o32.S +++ b/arch/mips/kernel/scall32-o32.S @@ -262,14 +262,11 @@ bad_alignment: LEAF(sys_syscall) subu t0, a0, __NR_O32_Linux # check syscall number sltiu v0, t0, __NR_O32_Linux_syscalls + 1 + beqz t0, einval # do not recurse sll t1, t0, 3 beqz v0, einval - lw t2, sys_call_table(t1) # syscall routine - li v1, 4000 - __NR_O32_Linux # index of sys_syscall - beq t0, v1, einval # do not recurse - /* Some syscalls like execve get their arguments from struct pt_regs and claim zero arguments in the syscall table. Thus we have to assume the worst case and shuffle around all potential arguments. diff --git a/arch/mips/kernel/scall64-o32.S b/arch/mips/kernel/scall64-o32.S index 6c7ef83..facb41a 100644 --- a/arch/mips/kernel/scall64-o32.S +++ b/arch/mips/kernel/scall64-o32.S @@ -174,14 +174,12 @@ not_o32_scall: END(handle_sys) LEAF(sys32_syscall) - sltu v0, a0, __NR_O32_Linux + __NR_O32_Linux_syscalls + 1 + subu t0, a0, __NR_O32_Linux # check syscall number + sltiu v0, t0, __NR_O32_Linux_syscalls + 1 + beqz t0, einval # do not recurse + dsll t1, t0, 3 beqz v0, einval - - dsll v0, a0, 3 - ld t2, (sys_call_table - (__NR_O32_Linux * 8))(v0) - - li v1, 4000 # indirect syscall number - beq a0, v1, einval # do not recurse + ld t2, sys_call_table(t1) # syscall routine move a0, a1 # shift argument registers move a1, a2 -- cgit v1.1 From 192cc7f0900a088e464635a59a63d974ee7a3e97 Mon Sep 17 00:00:00 2001 From: Tiejun Chen Date: Tue, 25 Nov 2008 16:33:20 +0800 Subject: MIPS: Malta: Add back RTC support With the conversion of MIPS to RTC_LIB the old RTC driver CONFIG_RTC became unselectable. Fix by setting up a platform device. Also enable RTC_CLASS so system time gets set from RTC on kernel initialization. [Ralf: Original patch by Tiejun; polished nice and shiny by me] Signed-off-by: Tiejun Chen Signed-off-by: Ralf Baechle --- arch/mips/configs/malta_defconfig | 39 +++++++++++++++++++++++-- arch/mips/mti-malta/malta-platform.c | 56 ++++++++++++++++++++++++++++++------ 2 files changed, 84 insertions(+), 11 deletions(-) (limited to 'arch') diff --git a/arch/mips/configs/malta_defconfig b/arch/mips/configs/malta_defconfig index 74daa0c..a699565 100644 --- a/arch/mips/configs/malta_defconfig +++ b/arch/mips/configs/malta_defconfig @@ -1126,7 +1126,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set # CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=m -CONFIG_RTC=y # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set # CONFIG_DRM is not set @@ -1199,7 +1198,43 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_MMC is not set # CONFIG_NEW_LEDS is not set # CONFIG_INFINIBAND is not set -# CONFIG_RTC_CLASS is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# SPI RTC drivers +# + +# +# Platform RTC drivers +# +CONFIG_RTC_DRV_CMOS=y +# CONFIG_RTC_DRV_DS1286 is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# # # DMA Engine support diff --git a/arch/mips/mti-malta/malta-platform.c b/arch/mips/mti-malta/malta-platform.c index 83b9bab..6a476f7 100644 --- a/arch/mips/mti-malta/malta-platform.c +++ b/arch/mips/mti-malta/malta-platform.c @@ -6,7 +6,10 @@ * Copyright (C) 2007 MIPS Technologies, Inc. * written by Ralf Baechle (ralf@linux-mips.org) * - * Probe driver for the Malta's UART ports: + * Copyright (C) 2008 Wind River Systems, Inc. + * updated by Tiejun Chen + * + * 1. Probe driver for the Malta's UART ports: * * o 2 ports in the SMC SuperIO * o 1 port in the CBUS UART, a discrete 16550 which normally is only used @@ -14,10 +17,14 @@ * * We don't use 8250_platform.c on Malta as it would result in the CBUS * UART becoming ttyS0. + * + * 2. Register RTC-CMOS platform device on Malta. */ #include #include #include +#include +#include #define SMC_PORT(base, int) \ { \ @@ -45,7 +52,7 @@ static struct plat_serial8250_port uart8250_data[] = { { }, }; -static struct platform_device uart8250_device = { +static struct platform_device malta_uart8250_device = { .name = "serial8250", .id = PLAT8250_DEV_PLATFORM2, .dev = { @@ -53,13 +60,44 @@ static struct platform_device uart8250_device = { }, }; -static int __init uart8250_init(void) +struct resource malta_rtc_resources[] = { + { + .start = RTC_PORT(0), + .end = RTC_PORT(7), + .flags = IORESOURCE_IO, + }, { + .start = RTC_IRQ, + .end = RTC_IRQ, + .flags = IORESOURCE_IRQ, + } +}; + +static struct platform_device malta_rtc_device = { + .name = "rtc_cmos", + .id = -1, + .resource = malta_rtc_resources, + .num_resources = ARRAY_SIZE(malta_rtc_resources), +}; + +static struct platform_device *malta_devices[] __initdata = { + &malta_uart8250_device, + &malta_rtc_device, +}; + +static int __init malta_add_devices(void) { - return platform_device_register(&uart8250_device); -} + int err; -module_init(uart8250_init); + err = platform_add_devices(malta_devices, ARRAY_SIZE(malta_devices)); + if (err) + return err; + + /* + * Set RTC to BCD mode to support current alarm code. + */ + CMOS_WRITE(CMOS_READ(RTC_CONTROL) & ~RTC_DM_BINARY, RTC_CONTROL); + + return 0; +} -MODULE_AUTHOR("Ralf Baechle "); -MODULE_LICENSE("GPL"); -MODULE_DESCRIPTION("8250 UART probe driver for the Malta CBUS UART"); +device_initcall(malta_add_devices); -- cgit v1.1 From 3e27cce60e434fc393fb261fb3ca455ba80a0b8b Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 1 Dec 2008 08:09:10 +0000 Subject: MIPS: IP22, Fulong, Malta: Update defconfigs. These haven't seen much attention for too long but particularly important enable RTC_CLASS and CONFIG_RTC_HCTOSYS so the wall clock time is set on kernel startup. Signed-off-by: Ralf Baechle --- arch/mips/configs/fulong_defconfig | 921 +++++++++++++++++++++---------------- arch/mips/configs/ip22_defconfig | 518 ++++++++++++++------- arch/mips/configs/malta_defconfig | 616 ++++++++++++++++--------- 3 files changed, 1273 insertions(+), 782 deletions(-) (limited to 'arch') diff --git a/arch/mips/configs/fulong_defconfig b/arch/mips/configs/fulong_defconfig index 6209800..b6698a2 100644 --- a/arch/mips/configs/fulong_defconfig +++ b/arch/mips/configs/fulong_defconfig @@ -1,63 +1,78 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.22-rc4 -# Mon Jun 11 00:23:51 2007 +# Linux kernel version: 2.6.28-rc6 +# Fri Nov 28 17:53:48 2008 # CONFIG_MIPS=y # # Machine selection # -CONFIG_LEMOTE_FULONG=y # CONFIG_MACH_ALCHEMY is not set # CONFIG_BASLER_EXCITE is not set +# CONFIG_BCM47XX is not set # CONFIG_MIPS_COBALT is not set # CONFIG_MACH_DECSTATION is not set # CONFIG_MACH_JAZZ is not set +# CONFIG_LASAT is not set +CONFIG_LEMOTE_FULONG=y # CONFIG_MIPS_MALTA is not set -# CONFIG_WR_PPMC is not set # CONFIG_MIPS_SIM is not set +# CONFIG_MACH_EMMA is not set +# CONFIG_MACH_VR41XX is not set +# CONFIG_NXP_STB220 is not set +# CONFIG_NXP_STB225 is not set # CONFIG_PNX8550_JBS is not set # CONFIG_PNX8550_STB810 is not set -# CONFIG_MACH_VR41XX is not set +# CONFIG_PMC_MSP is not set # CONFIG_PMC_YOSEMITE is not set -# CONFIG_MARKEINS is not set # CONFIG_SGI_IP22 is not set # CONFIG_SGI_IP27 is not set +# CONFIG_SGI_IP28 is not set # CONFIG_SGI_IP32 is not set -# CONFIG_SIBYTE_BIGSUR is not set -# CONFIG_SIBYTE_SWARM is not set -# CONFIG_SIBYTE_SENTOSA is not set -# CONFIG_SIBYTE_RHONE is not set -# CONFIG_SIBYTE_CARMEL is not set -# CONFIG_SIBYTE_LITTLESUR is not set # CONFIG_SIBYTE_CRHINE is not set +# CONFIG_SIBYTE_CARMEL is not set # CONFIG_SIBYTE_CRHONE is not set +# CONFIG_SIBYTE_RHONE is not set +# CONFIG_SIBYTE_SWARM is not set +# CONFIG_SIBYTE_LITTLESUR is not set +# CONFIG_SIBYTE_SENTOSA is not set +# CONFIG_SIBYTE_BIGSUR is not set # CONFIG_SNI_RM is not set -# CONFIG_TOSHIBA_JMR3927 is not set -# CONFIG_TOSHIBA_RBTX4927 is not set -# CONFIG_TOSHIBA_RBTX4938 is not set +# CONFIG_MACH_TX39XX is not set +# CONFIG_MACH_TX49XX is not set +# CONFIG_MIKROTIK_RB532 is not set +# CONFIG_WR_PPMC is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U32 is not set # CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_ARCH_SUPPORTS_OPROFILE=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_CEVT_R4K=y +CONFIG_CSRC_R4K=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y CONFIG_EARLY_PRINTK=y CONFIG_SYS_HAS_EARLY_PRINTK=y +# CONFIG_HOTPLUG_CPU is not set CONFIG_I8259=y # CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_ISA_DMA=y +CONFIG_GENERIC_ISA_DMA_SUPPORT_BROKEN=y # CONFIG_CPU_BIG_ENDIAN is not set CONFIG_CPU_LITTLE_ENDIAN=y CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y CONFIG_IRQ_CPU=y CONFIG_BOOT_ELF32=y CONFIG_MIPS_L1_CACHE_SHIFT=5 +CONFIG_HAVE_STD_PC_SERIAL_PORT=y # # CPU selection @@ -75,6 +90,7 @@ CONFIG_CPU_LOONGSON2=y # CONFIG_CPU_TX49XX is not set # CONFIG_CPU_R5000 is not set # CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R5500 is not set # CONFIG_CPU_R6000 is not set # CONFIG_CPU_NEVADA is not set # CONFIG_CPU_R8000 is not set @@ -101,7 +117,6 @@ CONFIG_BOARD_SCACHE=y CONFIG_MIPS_MT_DISABLED=y # CONFIG_MIPS_MT_SMP is not set # CONFIG_MIPS_MT_SMTC is not set -# CONFIG_MIPS_VPE_LOADER is not set CONFIG_CPU_HAS_WB=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y @@ -109,6 +124,7 @@ CONFIG_GENERIC_IRQ_PROBE=y CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_SYS_SUPPORTS_HIGHMEM=y CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_ARCH_SPARSEMEM_ENABLE=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y @@ -117,9 +133,17 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_SPARSEMEM_STATIC=y +CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y +CONFIG_PHYS_ADDR_T_64BIT=y CONFIG_ZONE_DMA_FLAG=0 +CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_48 is not set # CONFIG_HZ_100 is not set # CONFIG_HZ_128 is not set @@ -133,37 +157,40 @@ CONFIG_HZ=250 CONFIG_PREEMPT_VOLUNTARY=y # CONFIG_PREEMPT is not set # CONFIG_KEXEC is not set +CONFIG_SECCOMP=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # -# Code maturity level options +# General setup # CONFIG_EXPERIMENTAL=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 - -# -# General setup -# CONFIG_LOCALVERSION="lm32" # CONFIG_LOCALVERSION_AUTO is not set CONFIG_SWAP=y CONFIG_SYSVIPC=y -# CONFIG_IPC_NS is not set CONFIG_SYSVIPC_SYSCTL=y CONFIG_POSIX_MQUEUE=y CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set # CONFIG_TASKSTATS is not set -# CONFIG_UTS_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y # CONFIG_RELAY is not set +CONFIG_NAMESPACES=y +# CONFIG_UTS_NS is not set +# CONFIG_IPC_NS is not set +CONFIG_USER_NS=y +CONFIG_PID_NS=y # CONFIG_BLK_DEV_INITRD is not set # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y @@ -175,6 +202,8 @@ CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y +# CONFIG_PCSPKR_PLATFORM is not set +# CONFIG_COMPAT_BRK is not set CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_ANON_INODES=y @@ -183,29 +212,33 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y +CONFIG_PCI_QUIRKS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set +CONFIG_PROFILING=y +# CONFIG_MARKERS is not set +CONFIG_OPROFILE=m +CONFIG_HAVE_OPROFILE=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 - -# -# Loadable module support -# CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y CONFIG_MODULE_FORCE_UNLOAD=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y - -# -# Block layer -# CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set +CONFIG_BLK_DEV_BSG=y +# CONFIG_BLK_DEV_INTEGRITY is not set +CONFIG_BLOCK_COMPAT=y # # IO Schedulers @@ -219,19 +252,19 @@ CONFIG_IOSCHED_CFQ=y CONFIG_DEFAULT_CFQ=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y +CONFIG_FREEZER=y # # Bus options (PCI, PCMCIA, EISA, ISA, TC) # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y # CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_PCI_LEGACY=y CONFIG_ISA=y CONFIG_MMU=y - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -239,8 +272,9 @@ CONFIG_MMU=y # Executable file formats # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y -# CONFIG_BUILD_ELF64 is not set CONFIG_MIPS32_COMPAT=y CONFIG_COMPAT=y CONFIG_SYSVIPC_COMPAT=y @@ -251,14 +285,12 @@ CONFIG_BINFMT_ELF32=y # # Power management options # +CONFIG_ARCH_SUSPEND_POSSIBLE=y CONFIG_PM=y -# CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set -# CONFIG_PM_SYSFS_DEPRECATED is not set - -# -# Networking -# +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y CONFIG_NET=y # @@ -271,6 +303,7 @@ CONFIG_XFRM=y # CONFIG_XFRM_USER is not set # CONFIG_XFRM_SUB_POLICY is not set # CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y @@ -294,18 +327,17 @@ CONFIG_INET_TUNNEL=m # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set # CONFIG_INET_DIAG is not set # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TCP_MD5SIG is not set -# CONFIG_IP_VS is not set # CONFIG_IPV6 is not set -# CONFIG_INET6_XFRM_TUNNEL is not set -# CONFIG_INET6_TUNNEL is not set # CONFIG_NETWORK_SECMARK is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set +CONFIG_NETFILTER_ADVANCED=y # # Core Netfilter Configuration @@ -313,53 +345,59 @@ CONFIG_NETFILTER=y CONFIG_NETFILTER_NETLINK=m CONFIG_NETFILTER_NETLINK_QUEUE=m CONFIG_NETFILTER_NETLINK_LOG=m -# CONFIG_NF_CONNTRACK_ENABLED is not set # CONFIG_NF_CONNTRACK is not set CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m # CONFIG_NETFILTER_XT_TARGET_DSCP is not set CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m # CONFIG_NETFILTER_XT_TARGET_NFLOG is not set +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m +CONFIG_NETFILTER_XT_TARGET_RATEEST=m +CONFIG_NETFILTER_XT_TARGET_TRACE=m # CONFIG_NETFILTER_XT_TARGET_TCPMSS is not set +CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_DCCP=m # CONFIG_NETFILTER_XT_MATCH_DSCP is not set CONFIG_NETFILTER_XT_MATCH_ESP=m +# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set +CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m -# CONFIG_NETFILTER_XT_MATCH_POLICY is not set CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m +CONFIG_NETFILTER_XT_MATCH_OWNER=m +# CONFIG_NETFILTER_XT_MATCH_POLICY is not set CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m +CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m -# CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set +CONFIG_NETFILTER_XT_MATCH_TIME=m +CONFIG_NETFILTER_XT_MATCH_U32=m +# CONFIG_IP_VS is not set # # IP: Netfilter Configuration # +# CONFIG_NF_DEFRAG_IPV4 is not set CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_IPRANGE=m -CONFIG_IP_NF_MATCH_TOS=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_OWNER=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m CONFIG_IP_NF_TARGET_ULOG=m CONFIG_IP_NF_MANGLE=m -CONFIG_IP_NF_TARGET_TOS=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m CONFIG_IP_NF_RAW=m @@ -371,6 +409,7 @@ CONFIG_IP_NF_ARP_MANGLE=m # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -380,10 +419,6 @@ CONFIG_IP_NF_ARP_MANGLE=m # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set CONFIG_NET_CLS_ROUTE=y @@ -392,23 +427,25 @@ CONFIG_NET_CLS_ROUTE=y # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# +CONFIG_PHONET=m +CONFIG_WIRELESS=y # CONFIG_CFG80211 is not set +CONFIG_WIRELESS_OLD_REGULATORY=y CONFIG_WIRELESS_EXT=y +CONFIG_WIRELESS_EXT_SYSFS=y # CONFIG_MAC80211 is not set CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m # CONFIG_IEEE80211_CRYPT_CCMP is not set # CONFIG_IEEE80211_CRYPT_TKIP is not set -# CONFIG_IEEE80211_SOFTMAC is not set # CONFIG_RFKILL is not set +CONFIG_NET_9P=m +# CONFIG_NET_9P_DEBUG is not set # # Device Drivers @@ -417,14 +454,13 @@ CONFIG_IEEE80211_CRYPT_WEP=m # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=m +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" # CONFIG_SYS_HYPERVISOR is not set - -# -# Connector - unified userspace <-> kernelspace linker -# # CONFIG_CONNECTOR is not set CONFIG_MTD=m # CONFIG_MTD_DEBUG is not set @@ -443,6 +479,7 @@ CONFIG_MTD_BLOCK=m # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -482,6 +519,7 @@ CONFIG_MTD_PHYSMAP=m CONFIG_MTD_PHYSMAP_START=0x1fc00000 CONFIG_MTD_PHYSMAP_LEN=0x80000 CONFIG_MTD_PHYSMAP_BANKWIDTH=1 +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -506,21 +544,9 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=1 # UBI - Unsorted block images # # CONFIG_MTD_UBI is not set - -# -# Parallel port support -# # CONFIG_PARPORT is not set - -# -# Plug and Play support -# # CONFIG_PNP is not set -# CONFIG_PNPACPI is not set - -# -# Block devices -# +CONFIG_BLK_DEV=y # CONFIG_BLK_CPQ_DA is not set # CONFIG_BLK_CPQ_CISS_DA is not set # CONFIG_BLK_DEV_DAC960 is not set @@ -534,32 +560,28 @@ CONFIG_BLK_DEV_CRYPTOLOOP=m CONFIG_BLK_DEV_RAM=m CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 -CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_BLK_DEV_XIP is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set CONFIG_ATA_OVER_ETH=m - -# -# Misc devices -# -# CONFIG_PHANTOM is not set -# CONFIG_SGI_IOC4 is not set -# CONFIG_TIFM_CORE is not set -# CONFIG_BLINK is not set +# CONFIG_BLK_DEV_HD is not set +# CONFIG_MISC_DEVICES is not set +CONFIG_HAVE_IDE=y CONFIG_IDE=y -CONFIG_IDE_MAX_HWIFS=4 -CONFIG_BLK_DEV_IDE=y # -# Please see Documentation/ide.txt for help/info on IDE drives +# Please see Documentation/ide/ide.txt for help/info on IDE drives # +CONFIG_IDE_TIMINGS=y +CONFIG_IDE_ATAPI=y # CONFIG_BLK_DEV_IDE_SATA is not set -CONFIG_BLK_DEV_IDEDISK=y -CONFIG_IDEDISK_MULTI_MODE=y +CONFIG_IDE_GD=y +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set CONFIG_BLK_DEV_IDECD=y +CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y # CONFIG_BLK_DEV_IDETAPE is not set -# CONFIG_BLK_DEV_IDEFLOPPY is not set CONFIG_BLK_DEV_IDESCSI=y CONFIG_IDE_TASK_IOCTL=y CONFIG_IDE_PROC_FS=y @@ -568,24 +590,25 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set +CONFIG_BLK_DEV_IDEDMA_SFF=y + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y -CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_IDEPCI_PCIBUS_ORDER=y # CONFIG_BLK_DEV_OFFBOARD is not set CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set # CONFIG_BLK_DEV_CMD64X is not set # CONFIG_BLK_DEV_TRIFLEX is not set -# CONFIG_BLK_DEV_CY82C693 is not set # CONFIG_BLK_DEV_CS5520 is not set # CONFIG_BLK_DEV_CS5530 is not set -# CONFIG_BLK_DEV_HPT34X is not set # CONFIG_BLK_DEV_HPT366 is not set # CONFIG_BLK_DEV_JMICRON is not set # CONFIG_BLK_DEV_SC1200 is not set @@ -601,17 +624,28 @@ CONFIG_BLK_DEV_IDEDMA_PCI=y # CONFIG_BLK_DEV_TRM290 is not set CONFIG_BLK_DEV_VIA82CXXX=y # CONFIG_BLK_DEV_TC86C001 is not set -# CONFIG_IDE_ARM is not set -# CONFIG_IDE_CHIPSETS is not set + +# +# Other IDE chipsets support +# + +# +# Note: most of these also require special kernel boot parameters +# +# CONFIG_BLK_DEV_4DRIVES is not set +# CONFIG_BLK_DEV_ALI14XX is not set +# CONFIG_BLK_DEV_DTC2278 is not set +# CONFIG_BLK_DEV_HT6560B is not set +# CONFIG_BLK_DEV_QD65XX is not set +# CONFIG_BLK_DEV_UMC8672 is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set -# CONFIG_BLK_DEV_HD is not set # # SCSI device support # # CONFIG_RAID_ATTRS is not set CONFIG_SCSI=y +CONFIG_SCSI_DMA=y # CONFIG_SCSI_TGT is not set # CONFIG_SCSI_NETLINK is not set CONFIG_SCSI_PROC_FS=y @@ -644,88 +678,30 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set - -# -# SCSI low-level drivers -# -# CONFIG_ISCSI_TCP is not set -# CONFIG_BLK_DEV_3W_XXXX_RAID is not set -# CONFIG_SCSI_3W_9XXX is not set -# CONFIG_SCSI_ACARD is not set -# CONFIG_SCSI_AACRAID is not set -# CONFIG_SCSI_AIC7XXX is not set -# CONFIG_SCSI_AIC7XXX_OLD is not set -# CONFIG_SCSI_AIC79XX is not set -# CONFIG_SCSI_AIC94XX is not set -# CONFIG_SCSI_IN2000 is not set -# CONFIG_SCSI_ARCMSR is not set -# CONFIG_MEGARAID_NEWGEN is not set -# CONFIG_MEGARAID_LEGACY is not set -# CONFIG_MEGARAID_SAS is not set -# CONFIG_SCSI_HPTIOP is not set -# CONFIG_SCSI_DMX3191D is not set -# CONFIG_SCSI_DTC3280 is not set -# CONFIG_SCSI_FUTURE_DOMAIN is not set -# CONFIG_SCSI_GENERIC_NCR5380 is not set -# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set -# CONFIG_SCSI_IPS is not set -# CONFIG_SCSI_INITIO is not set -# CONFIG_SCSI_INIA100 is not set -# CONFIG_SCSI_NCR53C406A is not set -# CONFIG_SCSI_STEX is not set -# CONFIG_SCSI_SYM53C8XX_2 is not set -# CONFIG_SCSI_PAS16 is not set -# CONFIG_SCSI_PSI240I is not set -# CONFIG_SCSI_QLOGIC_FAS is not set -# CONFIG_SCSI_QLOGIC_1280 is not set -# CONFIG_SCSI_QLA_FC is not set -# CONFIG_SCSI_QLA_ISCSI is not set -# CONFIG_SCSI_LPFC is not set -# CONFIG_SCSI_SYM53C416 is not set -# CONFIG_SCSI_DC395x is not set -# CONFIG_SCSI_DC390T is not set -# CONFIG_SCSI_T128 is not set -# CONFIG_SCSI_DEBUG is not set -# CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_SRP_ATTRS is not set +# CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_DH is not set # CONFIG_ATA is not set - -# -# Old CD-ROM drivers (not SCSI, not IDE) -# -# CONFIG_CD_NO_IDESCSI is not set - -# -# Multi-device support (RAID and LVM) -# # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support # -# CONFIG_FIREWIRE is not set -# CONFIG_IEEE1394 is not set # -# I2O device support +# Enable only one of the two stacks, unless you know what you are doing # +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set # CONFIG_I2O is not set - -# -# Network device support -# CONFIG_NETDEVICES=y # CONFIG_DUMMY is not set # CONFIG_BONDING is not set +CONFIG_MACVLAN=m # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +CONFIG_VETH=m # CONFIG_ARCNET is not set CONFIG_PHYLIB=m @@ -740,29 +716,32 @@ CONFIG_CICADA_PHY=m # CONFIG_VITESSE_PHY is not set # CONFIG_SMSC_PHY is not set # CONFIG_BROADCOM_PHY is not set -# CONFIG_FIXED_PHY is not set - -# -# Ethernet (10 or 100Mbit) -# +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y +# CONFIG_AX88796 is not set # CONFIG_HAPPYMEAL is not set # CONFIG_SUNGEM is not set # CONFIG_CASSINI is not set # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_VENDOR_SMC is not set +# CONFIG_SMC91X is not set # CONFIG_DM9000 is not set # CONFIG_NET_VENDOR_RACAL is not set - -# -# Tulip family network device support -# # CONFIG_NET_TULIP is not set # CONFIG_AT1700 is not set # CONFIG_DEPCA is not set # CONFIG_HP100 is not set # CONFIG_NET_ISA is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set @@ -773,7 +752,6 @@ CONFIG_NET_PCI=y # CONFIG_FORCEDETH is not set # CONFIG_CS89x0 is not set # CONFIG_TC35815 is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set # CONFIG_E100 is not set # CONFIG_FEALNX is not set @@ -785,15 +763,21 @@ CONFIG_8139TOO=y # CONFIG_8139TOO_TUNE_TWISTER is not set # CONFIG_8139TOO_8129 is not set # CONFIG_8139_OLD_RX_RESET is not set +# CONFIG_R6040 is not set # CONFIG_SIS900 is not set # CONFIG_EPIC100 is not set # CONFIG_SUNDANCE is not set +# CONFIG_TLAN is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set +# CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set +# CONFIG_IP1000 is not set +# CONFIG_IGB is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -801,20 +785,29 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set -# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set +# CONFIG_ATL1E is not set +# CONFIG_JME is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_ENIC is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set +# CONFIG_MLX4_EN is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set +# CONFIG_BNX2X is not set +# CONFIG_QLGE is not set +# CONFIG_SFC is not set # CONFIG_TR is not set # @@ -822,6 +815,7 @@ CONFIG_NETDEV_10000=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set # # USB Network Adapters @@ -830,7 +824,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -844,25 +837,17 @@ CONFIG_PPP_DEFLATE=m CONFIG_PPP_BSDCOMP=m CONFIG_PPP_MPPE=m CONFIG_PPPOE=m +CONFIG_PPPOL2TP=m CONFIG_SLIP=m CONFIG_SLIP_COMPRESSED=y CONFIG_SLHC=m CONFIG_SLIP_SMART=y CONFIG_SLIP_MODE_SLIP6=y CONFIG_NET_FC=y -# CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set - -# -# ISDN subsystem -# # CONFIG_ISDN is not set - -# -# Telephony Support -# # CONFIG_PHONE is not set # @@ -870,6 +855,7 @@ CONFIG_NET_FC=y # CONFIG_INPUT=y CONFIG_INPUT_FF_MEMLESS=y +# CONFIG_INPUT_POLLDEV is not set # # Userland interfaces @@ -879,7 +865,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -900,9 +885,11 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=y # CONFIG_MOUSE_APPLETOUCH is not set +# CONFIG_MOUSE_BCM5974 is not set # CONFIG_MOUSE_INPORT is not set # CONFIG_MOUSE_LOGIBM is not set # CONFIG_MOUSE_PC110PAD is not set @@ -927,10 +914,13 @@ CONFIG_SERIO_LIBPS2=y # Character devices # CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y # CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set # # Serial drivers @@ -951,105 +941,152 @@ CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 - -# -# IPMI -# # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=y -CONFIG_RTC=y # CONFIG_DTLK is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set - -# -# TPM devices -# # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y CONFIG_I2C=m CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=m +CONFIG_I2C_HELPER_AUTO=y # -# I2C Algorithms +# I2C Hardware Bus support # -# CONFIG_I2C_ALGOBIT is not set -# CONFIG_I2C_ALGOPCF is not set -# CONFIG_I2C_ALGOPCA is not set # -# I2C Hardware Bus support +# PC SMBus host controller drivers # # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set # CONFIG_I2C_AMD756 is not set # CONFIG_I2C_AMD8111 is not set -# CONFIG_I2C_ELEKTOR is not set # CONFIG_I2C_I801 is not set -# CONFIG_I2C_I810 is not set +# CONFIG_I2C_ISCH is not set # CONFIG_I2C_PIIX4 is not set # CONFIG_I2C_NFORCE2 is not set -# CONFIG_I2C_OCORES is not set -# CONFIG_I2C_PARPORT_LIGHT is not set -# CONFIG_I2C_PROSAVAGE is not set -# CONFIG_I2C_SAVAGE4 is not set -# CONFIG_I2C_SIMTEC is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set -# CONFIG_I2C_STUB is not set -# CONFIG_I2C_TINY_USB is not set # CONFIG_I2C_VIA is not set CONFIG_I2C_VIAPRO=m + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Graphics adapter I2C/DDC channel drivers +# # CONFIG_I2C_VOODOO3 is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_ELEKTOR is not set # CONFIG_I2C_PCA_ISA is not set +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set # # Miscellaneous I2C Chip support # -# CONFIG_SENSORS_DS1337 is not set -# CONFIG_SENSORS_DS1374 is not set +# CONFIG_DS1682 is not set +# CONFIG_AT24 is not set # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set - -# -# SPI support -# # CONFIG_SPI is not set -# CONFIG_SPI_MASTER is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +# CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # -# Dallas's 1-wire bus +# Sonics Silicon Backplane # -# CONFIG_W1 is not set -# CONFIG_HWMON is not set +# CONFIG_SSB is not set # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_REGULATOR is not set # # Multimedia devices # + +# +# Multimedia core support +# CONFIG_VIDEO_DEV=m -CONFIG_VIDEO_V4L1=y +CONFIG_VIDEO_V4L2_COMMON=m +CONFIG_VIDEO_ALLOW_V4L1=y CONFIG_VIDEO_V4L1_COMPAT=y -CONFIG_VIDEO_V4L2=y +# CONFIG_DVB_CORE is not set +CONFIG_VIDEO_MEDIA=m + +# +# Multimedia drivers +# +CONFIG_MEDIA_ATTACH=y +CONFIG_MEDIA_TUNER=m +CONFIG_MEDIA_TUNER_CUSTOMIZE=y +CONFIG_MEDIA_TUNER_SIMPLE=m +CONFIG_MEDIA_TUNER_TDA8290=m +CONFIG_MEDIA_TUNER_TDA827X=m +CONFIG_MEDIA_TUNER_TDA18271=m +CONFIG_MEDIA_TUNER_TDA9887=m +CONFIG_MEDIA_TUNER_TEA5761=m +CONFIG_MEDIA_TUNER_TEA5767=m +CONFIG_MEDIA_TUNER_MT20XX=m +CONFIG_MEDIA_TUNER_MT2060=m +CONFIG_MEDIA_TUNER_MT2266=m +CONFIG_MEDIA_TUNER_MT2131=m +CONFIG_MEDIA_TUNER_QT1010=m +CONFIG_MEDIA_TUNER_XC2028=m +CONFIG_MEDIA_TUNER_XC5000=m +CONFIG_MEDIA_TUNER_MXL5005S=m +CONFIG_MEDIA_TUNER_MXL5007T=m +CONFIG_VIDEO_V4L2=m +CONFIG_VIDEO_V4L1=m +CONFIG_VIDEOBUF_GEN=m +CONFIG_VIDEOBUF_VMALLOC=m +CONFIG_VIDEOBUF_DMA_CONTIG=m CONFIG_VIDEO_CAPTURE_DRIVERS=y # CONFIG_VIDEO_ADV_DEBUG is not set +# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set CONFIG_VIDEO_HELPER_CHIPS_AUTO=y # CONFIG_VIDEO_VIVI is not set # CONFIG_VIDEO_BT848 is not set @@ -1058,17 +1095,46 @@ CONFIG_VIDEO_HELPER_CHIPS_AUTO=y # CONFIG_VIDEO_CPIA2 is not set # CONFIG_VIDEO_SAA5246A is not set # CONFIG_VIDEO_SAA5249 is not set -# CONFIG_TUNER_3036 is not set # CONFIG_VIDEO_STRADIS is not set # CONFIG_VIDEO_SAA7134 is not set # CONFIG_VIDEO_MXB is not set -# CONFIG_VIDEO_DPC is not set # CONFIG_VIDEO_HEXIUM_ORION is not set # CONFIG_VIDEO_HEXIUM_GEMINI is not set # CONFIG_VIDEO_CX88 is not set # CONFIG_VIDEO_IVTV is not set # CONFIG_VIDEO_CAFE_CCIC is not set +CONFIG_SOC_CAMERA=m +CONFIG_SOC_CAMERA_MT9M001=m +CONFIG_SOC_CAMERA_MT9M111=m +CONFIG_SOC_CAMERA_MT9V022=m +CONFIG_SOC_CAMERA_PLATFORM=m +CONFIG_VIDEO_SH_MOBILE_CEU=m CONFIG_V4L_USB_DRIVERS=y +CONFIG_USB_VIDEO_CLASS=m +CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV=y +CONFIG_USB_GSPCA=m +CONFIG_USB_M5602=m +CONFIG_USB_GSPCA_CONEX=m +CONFIG_USB_GSPCA_ETOMS=m +CONFIG_USB_GSPCA_FINEPIX=m +CONFIG_USB_GSPCA_MARS=m +CONFIG_USB_GSPCA_OV519=m +CONFIG_USB_GSPCA_PAC207=m +CONFIG_USB_GSPCA_PAC7311=m +CONFIG_USB_GSPCA_SONIXB=m +CONFIG_USB_GSPCA_SONIXJ=m +CONFIG_USB_GSPCA_SPCA500=m +CONFIG_USB_GSPCA_SPCA501=m +CONFIG_USB_GSPCA_SPCA505=m +CONFIG_USB_GSPCA_SPCA506=m +CONFIG_USB_GSPCA_SPCA508=m +CONFIG_USB_GSPCA_SPCA561=m +CONFIG_USB_GSPCA_STK014=m +CONFIG_USB_GSPCA_SUNPLUS=m +CONFIG_USB_GSPCA_T613=m +CONFIG_USB_GSPCA_TV8532=m +CONFIG_USB_GSPCA_VC032X=m +CONFIG_USB_GSPCA_ZC3XX=m # CONFIG_VIDEO_PVRUSB2 is not set # CONFIG_VIDEO_EM28XX is not set # CONFIG_VIDEO_USBVISION is not set @@ -1079,7 +1145,6 @@ CONFIG_USB_KONICAWC=m CONFIG_USB_QUICKCAM_MESSENGER=m CONFIG_USB_ET61X251=m # CONFIG_VIDEO_OVCAMCHIP is not set -# CONFIG_USB_W9968CF is not set CONFIG_USB_OV511=m CONFIG_USB_SE401=m CONFIG_USB_SN9C102=m @@ -1088,6 +1153,8 @@ CONFIG_USB_ZC0301=m CONFIG_USB_PWC=m # CONFIG_USB_PWC_DEBUG is not set # CONFIG_USB_ZR364XX is not set +CONFIG_USB_STKWEBCAM=m +CONFIG_USB_S2255=m CONFIG_RADIO_ADAPTERS=y # CONFIG_RADIO_CADET is not set # CONFIG_RADIO_RTRACK is not set @@ -1104,33 +1171,30 @@ CONFIG_RADIO_ADAPTERS=y # CONFIG_RADIO_TYPHOON is not set # CONFIG_RADIO_ZOLTRIX is not set # CONFIG_USB_DSBR is not set -# CONFIG_DVB_CORE is not set +CONFIG_USB_SI470X=m +CONFIG_USB_MR800=m CONFIG_DAB=y # CONFIG_USB_DABUSB is not set # # Graphics support # -CONFIG_BACKLIGHT_LCD_SUPPORT=y -CONFIG_BACKLIGHT_CLASS_DEVICE=y -CONFIG_LCD_CLASS_DEVICE=m - -# -# Display device support -# -# CONFIG_DISPLAY_SUPPORT is not set +# CONFIG_DRM is not set # CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set # CONFIG_FB_SYS_FOPS is not set -CONFIG_FB_DEFERRED_IO=y # CONFIG_FB_SVGALIB is not set # CONFIG_FB_MACMODES is not set CONFIG_FB_BACKLIGHT=y @@ -1158,16 +1222,30 @@ CONFIG_FB_RADEON_BACKLIGHT=y # CONFIG_FB_S3 is not set # CONFIG_FB_SAVAGE is not set # CONFIG_FB_SIS is not set +# CONFIG_FB_VIA is not set # CONFIG_FB_NEOMAGIC is not set # CONFIG_FB_KYRO is not set # CONFIG_FB_3DFX is not set # CONFIG_FB_VOODOO1 is not set -# CONFIG_FB_SMIVGX is not set # CONFIG_FB_VT8623 is not set # CONFIG_FB_TRIDENT is not set # CONFIG_FB_ARK is not set # CONFIG_FB_PM3 is not set +# CONFIG_FB_CARMINE is not set # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=m +# CONFIG_LCD_ILI9320 is not set +# CONFIG_LCD_PLATFORM is not set +CONFIG_BACKLIGHT_CLASS_DEVICE=y +# CONFIG_BACKLIGHT_CORGI is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set # # Console display driver support @@ -1176,20 +1254,14 @@ CONFIG_FB_RADEON_BACKLIGHT=y # CONFIG_MDA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set # CONFIG_FONTS is not set CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y # CONFIG_LOGO is not set - -# -# Sound -# CONFIG_SOUND=y - -# -# Advanced Linux Sound Architecture -# +CONFIG_SOUND_OSS_CORE=y CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m @@ -1201,28 +1273,22 @@ CONFIG_SND_MIXER_OSS=m CONFIG_SND_PCM_OSS=m CONFIG_SND_PCM_OSS_PLUGINS=y CONFIG_SND_SEQUENCER_OSS=y -CONFIG_SND_RTCTIMER=m -CONFIG_SND_SEQ_RTCTIMER_DEFAULT=y # CONFIG_SND_DYNAMIC_MINORS is not set CONFIG_SND_SUPPORT_OLD_API=y CONFIG_SND_VERBOSE_PROCFS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set - -# -# Generic devices -# +CONFIG_SND_VMASTER=y CONFIG_SND_MPU401_UART=m CONFIG_SND_AC97_CODEC=m +CONFIG_SND_DRIVERS=y # CONFIG_SND_DUMMY is not set # CONFIG_SND_VIRMIDI is not set # CONFIG_SND_MTPAV is not set # CONFIG_SND_SERIAL_U16550 is not set # CONFIG_SND_MPU401 is not set - -# -# PCI devices -# +# CONFIG_SND_AC97_POWER_SAVE is not set +CONFIG_SND_PCI=y # CONFIG_SND_AD1889 is not set # CONFIG_SND_ALS300 is not set # CONFIG_SND_ALI5451 is not set @@ -1231,10 +1297,12 @@ CONFIG_SND_AC97_CODEC=m # CONFIG_SND_AU8810 is not set # CONFIG_SND_AU8820 is not set # CONFIG_SND_AU8830 is not set +# CONFIG_SND_AW2 is not set # CONFIG_SND_AZT3328 is not set # CONFIG_SND_BT87X is not set # CONFIG_SND_CA0106 is not set # CONFIG_SND_CMIPCI is not set +# CONFIG_SND_OXYGEN is not set # CONFIG_SND_CS4281 is not set # CONFIG_SND_CS46XX is not set # CONFIG_SND_DARLA20 is not set @@ -1259,6 +1327,7 @@ CONFIG_SND_AC97_CODEC=m # CONFIG_SND_HDA_INTEL is not set # CONFIG_SND_HDSP is not set # CONFIG_SND_HDSPM is not set +# CONFIG_SND_HIFIER is not set # CONFIG_SND_ICE1712 is not set # CONFIG_SND_ICE1724 is not set # CONFIG_SND_INTEL8X0 is not set @@ -1276,43 +1345,26 @@ CONFIG_SND_AC97_CODEC=m # CONFIG_SND_TRIDENT is not set CONFIG_SND_VIA82XX=m # CONFIG_SND_VIA82XX_MODEM is not set +# CONFIG_SND_VIRTUOSO is not set # CONFIG_SND_VX222 is not set # CONFIG_SND_YMFPCI is not set -# CONFIG_SND_AC97_POWER_SAVE is not set - -# -# ALSA MIPS devices -# - -# -# USB devices -# +CONFIG_SND_MIPS=y +CONFIG_SND_USB=y # CONFIG_SND_USB_AUDIO is not set # CONFIG_SND_USB_CAIAQ is not set - -# -# System on Chip audio support -# # CONFIG_SND_SOC is not set - -# -# Open Sound System -# # CONFIG_SOUND_PRIME is not set CONFIG_AC97_BUS=m - -# -# HID Devices -# +CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +CONFIG_HIDRAW=y # # USB Input Devices # CONFIG_USB_HID=m -# CONFIG_USB_HIDINPUT_POWERBOOK is not set -# CONFIG_HID_FF is not set +CONFIG_HID_PID=y CONFIG_USB_HIDDEV=y # @@ -1322,13 +1374,39 @@ CONFIG_USB_HIDDEV=y # CONFIG_USB_MOUSE is not set # -# USB support -# +# Special HID drivers +# +CONFIG_HID_COMPAT=y +CONFIG_HID_A4TECH=m +CONFIG_HID_APPLE=m +CONFIG_HID_BELKIN=m +CONFIG_HID_BRIGHT=m +CONFIG_HID_CHERRY=m +CONFIG_HID_CHICONY=m +CONFIG_HID_CYPRESS=m +CONFIG_HID_DELL=m +CONFIG_HID_EZKEY=m +CONFIG_HID_GYRATION=m +CONFIG_HID_LOGITECH=m +CONFIG_LOGITECH_FF=y +CONFIG_LOGIRUMBLEPAD2_FF=y +CONFIG_HID_MICROSOFT=m +CONFIG_HID_MONTEREY=m +CONFIG_HID_PANTHERLORD=m +# CONFIG_PANTHERLORD_FF is not set +CONFIG_HID_PETALYNX=m +CONFIG_HID_SAMSUNG=m +CONFIG_HID_SONY=m +CONFIG_HID_SUNPLUS=m +# CONFIG_THRUSTMASTER_FF is not set +CONFIG_ZEROPLUS_FF=m +CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set +CONFIG_USB_ANNOUNCE_NEW_DEVICES=y # # Miscellaneous USB options @@ -1338,35 +1416,46 @@ CONFIG_USB_DEVICEFS=y # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_SUSPEND is not set # CONFIG_USB_OTG is not set +CONFIG_USB_OTG_WHITELIST=y +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +# CONFIG_USB_MON is not set +# CONFIG_USB_WUSB is not set +CONFIG_USB_WUSB_CBAF=m +# CONFIG_USB_WUSB_CBAF_DEBUG is not set # # USB Host Controller Drivers # +CONFIG_USB_C67X00_HCD=m CONFIG_USB_EHCI_HCD=y -CONFIG_USB_EHCI_SPLIT_ISO=y CONFIG_USB_EHCI_ROOT_HUB_TT=y CONFIG_USB_EHCI_TT_NEWSCHED=y -# CONFIG_USB_EHCI_BIG_ENDIAN_MMIO is not set # CONFIG_USB_ISP116X_HCD is not set +CONFIG_USB_ISP1760_HCD=m CONFIG_USB_OHCI_HCD=y # CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set # CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set CONFIG_USB_OHCI_LITTLE_ENDIAN=y CONFIG_USB_UHCI_HCD=m # CONFIG_USB_SL811_HCD is not set +CONFIG_USB_R8A66597_HCD=m +# CONFIG_USB_WHCI_HCD is not set +# CONFIG_USB_HWA_HCD is not set # # USB Device Class drivers # CONFIG_USB_ACM=y CONFIG_USB_PRINTER=y +CONFIG_USB_WDM=m +CONFIG_USB_TMC=m # -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; # # -# may also be needed; see USB_STORAGE Help for more information +# see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_DEBUG is not set @@ -1379,7 +1468,9 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set # CONFIG_USB_STORAGE_ALAUDA is not set +CONFIG_USB_STORAGE_ONETOUCH=y # CONFIG_USB_STORAGE_KARMA is not set +CONFIG_USB_STORAGE_CYPRESS_ATACB=y CONFIG_USB_LIBUSUAL=y # @@ -1387,15 +1478,10 @@ CONFIG_USB_LIBUSUAL=y # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set -# CONFIG_USB_MON is not set # # USB port drivers # - -# -# USB Serial Converter support -# # CONFIG_USB_SERIAL is not set # @@ -1404,7 +1490,7 @@ CONFIG_USB_LIBUSUAL=y # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set -# CONFIG_USB_AUERSWALD is not set +CONFIG_USB_SEVSEG=m # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set @@ -1421,56 +1507,75 @@ CONFIG_USB_LIBUSUAL=y # CONFIG_USB_TRANCEVIBRATOR is not set # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set - -# -# USB DSL modem support -# - -# -# USB Gadget Support -# +CONFIG_USB_ISIGHTFW=m +CONFIG_USB_VST=m # CONFIG_USB_GADGET is not set +# CONFIG_UWB is not set # CONFIG_MMC is not set - -# -# LED devices -# +# CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set - -# -# LED drivers -# - -# -# LED Triggers -# - -# -# InfiniBand support -# +# CONFIG_ACCESSIBILITY is not set # CONFIG_INFINIBAND is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=m # -# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# RTC interfaces # +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +CONFIG_RTC_INTF_DEV_UIE_EMUL=y +# CONFIG_RTC_DRV_TEST is not set # -# Real Time Clock +# I2C RTC drivers # -# CONFIG_RTC_CLASS is not set +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set # -# DMA Engine support +# SPI RTC drivers # -# CONFIG_DMA_ENGINE is not set # -# DMA Clients +# Platform RTC drivers # +CONFIG_RTC_DRV_CMOS=m +# CONFIG_RTC_DRV_DS1286 is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_V3020 is not set # -# DMA Devices +# on-CPU RTC drivers # +# CONFIG_DMADEVICES is not set +CONFIG_UIO=m +CONFIG_UIO_CIF=m +# CONFIG_UIO_PDRV is not set +# CONFIG_UIO_PDRV_GENIRQ is not set +# CONFIG_UIO_SMX is not set +# CONFIG_UIO_SERCOS3 is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -1478,27 +1583,31 @@ CONFIG_USB_LIBUSUAL=y CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XATTR is not set CONFIG_EXT2_FS_XIP=y -CONFIG_FS_XIP=y CONFIG_EXT3_FS=y # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +CONFIG_EXT4_FS=m +CONFIG_EXT4DEV_COMPAT=y +CONFIG_EXT4_FS_XATTR=y +CONFIG_EXT4_FS_POSIX_ACL=y +CONFIG_EXT4_FS_SECURITY=y +CONFIG_FS_XIP=y CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set +CONFIG_JBD2=m +CONFIG_FS_MBCACHE=m CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set # CONFIG_REISERFS_FS_XATTR is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_ROMFS_FS is not set +CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set -CONFIG_DNOTIFY=y CONFIG_AUTOFS_FS=y CONFIG_AUTOFS4_FS=y CONFIG_FUSE_FS=y @@ -1530,11 +1639,11 @@ CONFIG_NTFS_RW=y CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1550,25 +1659,23 @@ CONFIG_RAMFS=y # CONFIG_JFFS2_FS is not set # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +CONFIG_OMFS_FS=m # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=m CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y CONFIG_NFS_V4=y -CONFIG_NFS_DIRECTIO=y CONFIG_NFSD=m CONFIG_NFSD_V2_ACL=y CONFIG_NFSD_V3=y CONFIG_NFSD_V3_ACL=y CONFIG_NFSD_V4=y -CONFIG_NFSD_TCP=y CONFIG_LOCKD=m CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=m @@ -1576,7 +1683,7 @@ CONFIG_NFS_ACL_SUPPORT=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=m CONFIG_SUNRPC_GSS=m -# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=m # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -1616,10 +1723,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="utf8" # CONFIG_NLS_CODEPAGE_437 is not set @@ -1660,30 +1763,31 @@ CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=y - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # -# Profiling support -# -CONFIG_PROFILING=y -CONFIG_OPROFILE=m - -# # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y # CONFIG_ENABLE_MUST_CHECK is not set +CONFIG_FRAME_WARN=2048 # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set -CONFIG_CROSSCOMPILE=y +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +CONFIG_DYNAMIC_PRINTK_DEBUG=y +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y CONFIG_CMDLINE="" # @@ -1691,64 +1795,113 @@ CONFIG_CMDLINE="" # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +CONFIG_SECURITY_FILE_CAPABILITIES=y +CONFIG_CRYPTO=y # -# Cryptographic options +# Crypto core or helper # -CONFIG_CRYPTO=y +CONFIG_CRYPTO_FIPS=y CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_AEAD=y +CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_GF128MUL=m +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_AUTHENC=m +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +CONFIG_CRYPTO_CCM=m +CONFIG_CRYPTO_GCM=m +CONFIG_CRYPTO_SEQIV=m + +# +# Block modes +# +CONFIG_CRYPTO_CBC=m +CONFIG_CRYPTO_CTR=m +CONFIG_CRYPTO_CTS=m +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +CONFIG_CRYPTO_XTS=m + +# +# Hash modes +# CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_XCBC is not set -# CONFIG_CRYPTO_NULL is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=m +# CONFIG_CRYPTO_MICHAEL_MIC is not set +CONFIG_CRYPTO_RMD128=m +CONFIG_CRYPTO_RMD160=m +CONFIG_CRYPTO_RMD256=m +CONFIG_CRYPTO_RMD320=m CONFIG_CRYPTO_SHA1=m # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set -# CONFIG_CRYPTO_WP512 is not set # CONFIG_CRYPTO_TGR192 is not set -# CONFIG_CRYPTO_GF128MUL is not set -CONFIG_CRYPTO_ECB=m -CONFIG_CRYPTO_CBC=m -CONFIG_CRYPTO_PCBC=m -# CONFIG_CRYPTO_LRW is not set -# CONFIG_CRYPTO_CRYPTD is not set -CONFIG_CRYPTO_DES=m -# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +CONFIG_CRYPTO_AES=m +# CONFIG_CRYPTO_ANUBIS is not set +CONFIG_CRYPTO_ARC4=m # CONFIG_CRYPTO_BLOWFISH is not set -# CONFIG_CRYPTO_TWOFISH is not set -# CONFIG_CRYPTO_SERPENT is not set -# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_CAST5 is not set # CONFIG_CRYPTO_CAST6 is not set -# CONFIG_CRYPTO_TEA is not set -CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_DES=m +# CONFIG_CRYPTO_FCRYPT is not set # CONFIG_CRYPTO_KHAZAD is not set -# CONFIG_CRYPTO_ANUBIS is not set +CONFIG_CRYPTO_SALSA20=m +CONFIG_CRYPTO_SEED=m +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# CONFIG_CRYPTO_DEFLATE=m -# CONFIG_CRYPTO_MICHAEL_MIC is not set -# CONFIG_CRYPTO_CRC32C is not set -# CONFIG_CRYPTO_CAMELLIA is not set -# CONFIG_CRYPTO_TEST is not set +CONFIG_CRYPTO_LZO=m # -# Hardware crypto devices +# Random Number Generation # +CONFIG_CRYPTO_ANSI_CPRNG=m +# CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y CONFIG_CRC_CCITT=y -# CONFIG_CRC16 is not set -# CONFIG_CRC_ITU_T is not set +CONFIG_CRC16=m +# CONFIG_CRC_T10DIF is not set +CONFIG_CRC_ITU_T=m CONFIG_CRC32=y +CONFIG_CRC7=m # CONFIG_LIBCRC32C is not set CONFIG_ZLIB_INFLATE=m CONFIG_ZLIB_DEFLATE=m +CONFIG_LZO_COMPRESS=m +CONFIG_LZO_DECOMPRESS=m CONFIG_TEXTSEARCH=y CONFIG_TEXTSEARCH_KMP=m CONFIG_TEXTSEARCH_BM=m diff --git a/arch/mips/configs/ip22_defconfig b/arch/mips/configs/ip22_defconfig index f719bf5..1158228 100644 --- a/arch/mips/configs/ip22_defconfig +++ b/arch/mips/configs/ip22_defconfig @@ -1,30 +1,34 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc2 -# Tue Aug 7 12:39:49 2007 +# Linux kernel version: 2.6.28-rc6 +# Fri Nov 28 15:41:33 2008 # CONFIG_MIPS=y # # Machine selection # -CONFIG_ZONE_DMA=y # CONFIG_MACH_ALCHEMY is not set # CONFIG_BASLER_EXCITE is not set +# CONFIG_BCM47XX is not set # CONFIG_MIPS_COBALT is not set # CONFIG_MACH_DECSTATION is not set # CONFIG_MACH_JAZZ is not set +# CONFIG_LASAT is not set # CONFIG_LEMOTE_FULONG is not set # CONFIG_MIPS_MALTA is not set # CONFIG_MIPS_SIM is not set -# CONFIG_MARKEINS is not set +# CONFIG_MACH_EMMA is not set # CONFIG_MACH_VR41XX is not set +# CONFIG_NXP_STB220 is not set +# CONFIG_NXP_STB225 is not set # CONFIG_PNX8550_JBS is not set # CONFIG_PNX8550_STB810 is not set # CONFIG_PMC_MSP is not set # CONFIG_PMC_YOSEMITE is not set CONFIG_SGI_IP22=y # CONFIG_SGI_IP27 is not set +# CONFIG_SGI_IP28 is not set # CONFIG_SGI_IP32 is not set # CONFIG_SIBYTE_CRHINE is not set # CONFIG_SIBYTE_CARMEL is not set @@ -35,34 +39,49 @@ CONFIG_SGI_IP22=y # CONFIG_SIBYTE_SENTOSA is not set # CONFIG_SIBYTE_BIGSUR is not set # CONFIG_SNI_RM is not set -# CONFIG_TOSHIBA_JMR3927 is not set -# CONFIG_TOSHIBA_RBTX4927 is not set -# CONFIG_TOSHIBA_RBTX4938 is not set +# CONFIG_MACH_TX39XX is not set +# CONFIG_MACH_TX49XX is not set +# CONFIG_MIKROTIK_RB532 is not set # CONFIG_WR_PPMC is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U32 is not set # CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_ARCH_SUPPORTS_OPROFILE=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y # CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set CONFIG_ARC=y +CONFIG_CEVT_R4K=y +CONFIG_CSRC_R4K=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y CONFIG_EARLY_PRINTK=y CONFIG_SYS_HAS_EARLY_PRINTK=y +# CONFIG_HOTPLUG_CPU is not set +CONFIG_I8259=y # CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_ISA_DMA=y CONFIG_GENERIC_ISA_DMA_SUPPORT_BROKEN=y CONFIG_CPU_BIG_ENDIAN=y # CONFIG_CPU_LITTLE_ENDIAN is not set CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y CONFIG_IRQ_CPU=y CONFIG_SWAP_IO_SPACE=y +CONFIG_SGI_HAS_INDYDOG=y +CONFIG_SGI_HAS_HAL2=y +CONFIG_SGI_HAS_SEEQ=y +CONFIG_SGI_HAS_WD93=y +CONFIG_SGI_HAS_ZILOG=y +CONFIG_SGI_HAS_I8042=y +CONFIG_DEFAULT_SGI_PARTITION=y CONFIG_ARC32=y CONFIG_BOOT_ELF32=y -CONFIG_MIPS_L1_CACHE_SHIFT=5 +CONFIG_MIPS_L1_CACHE_SHIFT=7 CONFIG_ARC_CONSOLE=y CONFIG_ARC_PROMLIB=y @@ -82,6 +101,7 @@ CONFIG_ARC_PROMLIB=y # CONFIG_CPU_TX49XX is not set CONFIG_CPU_R5000=y # CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R5500 is not set # CONFIG_CPU_R6000 is not set # CONFIG_CPU_NEVADA is not set # CONFIG_CPU_R8000 is not set @@ -115,18 +135,24 @@ CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set -CONFIG_ZONE_DMA_FLAG=1 -CONFIG_BOUNCE=y +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=0 CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_48 is not set # CONFIG_HZ_100 is not set # CONFIG_HZ_128 is not set @@ -159,13 +185,20 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set -# CONFIG_USER_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y CONFIG_RELAY=y +CONFIG_NAMESPACES=y +CONFIG_UTS_NS=y +CONFIG_IPC_NS=y +CONFIG_USER_NS=y +CONFIG_PID_NS=y # CONFIG_BLK_DEV_INITRD is not set # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y @@ -177,6 +210,8 @@ CONFIG_KALLSYMS=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y +# CONFIG_PCSPKR_PLATFORM is not set +# CONFIG_COMPAT_BRK is not set CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_ANON_INODES=y @@ -185,14 +220,21 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y @@ -203,6 +245,7 @@ CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -216,6 +259,8 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Bus options (PCI, PCMCIA, EISA, ISA, TC) @@ -224,29 +269,24 @@ CONFIG_HW_HAS_EISA=y # CONFIG_ARCH_SUPPORTS_MSI is not set # CONFIG_EISA is not set CONFIG_MMU=y - -# -# PCCARD (PCMCIA/CardBus) support -# +CONFIG_I8253=y # # Executable file formats # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m CONFIG_TRAD_SIGNALS=y # # Power management options # +CONFIG_ARCH_SUSPEND_POSSIBLE=y CONFIG_PM=y -# CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set # CONFIG_SUSPEND is not set - -# -# Networking -# CONFIG_NET=y # @@ -259,6 +299,8 @@ CONFIG_XFRM=y CONFIG_XFRM_USER=m # CONFIG_XFRM_SUB_POLICY is not set CONFIG_XFRM_MIGRATE=y +# CONFIG_XFRM_STATISTICS is not set +CONFIG_XFRM_IPCOMP=m CONFIG_NET_KEY=y CONFIG_NET_KEY_MIGRATE=y CONFIG_INET=y @@ -282,42 +324,13 @@ CONFIG_INET_TUNNEL=m CONFIG_INET_XFRM_MODE_TRANSPORT=m CONFIG_INET_XFRM_MODE_TUNNEL=m CONFIG_INET_XFRM_MODE_BEET=m +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" CONFIG_TCP_MD5SIG=y -CONFIG_IP_VS=m -# CONFIG_IP_VS_DEBUG is not set -CONFIG_IP_VS_TAB_BITS=12 - -# -# IPVS transport protocol load balancing support -# -CONFIG_IP_VS_PROTO_TCP=y -CONFIG_IP_VS_PROTO_UDP=y -CONFIG_IP_VS_PROTO_ESP=y -CONFIG_IP_VS_PROTO_AH=y - -# -# IPVS scheduler -# -CONFIG_IP_VS_RR=m -CONFIG_IP_VS_WRR=m -CONFIG_IP_VS_LC=m -CONFIG_IP_VS_WLC=m -CONFIG_IP_VS_LBLC=m -CONFIG_IP_VS_LBLCR=m -CONFIG_IP_VS_DH=m -CONFIG_IP_VS_SH=m -CONFIG_IP_VS_SED=m -CONFIG_IP_VS_NQ=m - -# -# IPVS application helper -# -CONFIG_IP_VS_FTP=m CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -334,12 +347,16 @@ CONFIG_INET6_XFRM_MODE_TUNNEL=m CONFIG_INET6_XFRM_MODE_BEET=m CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m CONFIG_IPV6_SIT=m +CONFIG_IPV6_NDISC_NODETYPE=y CONFIG_IPV6_TUNNEL=m CONFIG_IPV6_MULTIPLE_TABLES=y CONFIG_IPV6_SUBTREES=y +CONFIG_IPV6_MROUTE=y +CONFIG_IPV6_PIMSM_V2=y CONFIG_NETWORK_SECMARK=y CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set +CONFIG_NETFILTER_ADVANCED=y # # Core Netfilter Configuration @@ -347,12 +364,12 @@ CONFIG_NETFILTER=y CONFIG_NETFILTER_NETLINK=m CONFIG_NETFILTER_NETLINK_QUEUE=m CONFIG_NETFILTER_NETLINK_LOG=m -CONFIG_NF_CONNTRACK_ENABLED=m CONFIG_NF_CONNTRACK=m CONFIG_NF_CT_ACCT=y CONFIG_NF_CONNTRACK_MARK=y CONFIG_NF_CONNTRACK_SECMARK=y CONFIG_NF_CONNTRACK_EVENTS=y +CONFIG_NF_CT_PROTO_DCCP=m CONFIG_NF_CT_PROTO_GRE=m CONFIG_NF_CT_PROTO_SCTP=m CONFIG_NF_CT_PROTO_UDPLITE=m @@ -366,18 +383,22 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m CONFIG_NF_CT_NETLINK=m +CONFIG_NETFILTER_TPROXY=m CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m +CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m CONFIG_NETFILTER_XT_TARGET_DSCP=m CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m +CONFIG_NETFILTER_XT_TARGET_RATEEST=m +CONFIG_NETFILTER_XT_TARGET_TPROXY=m CONFIG_NETFILTER_XT_TARGET_TRACE=m CONFIG_NETFILTER_XT_TARGET_SECMARK=m -CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m CONFIG_NETFILTER_XT_TARGET_TCPMSS=m +CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m @@ -386,39 +407,75 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m CONFIG_NETFILTER_XT_MATCH_DSCP=m CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m +CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m -CONFIG_NETFILTER_XT_MATCH_POLICY=m CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m +CONFIG_NETFILTER_XT_MATCH_OWNER=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m +CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT=y CONFIG_NETFILTER_XT_MATCH_SCTP=m +CONFIG_NETFILTER_XT_MATCH_SOCKET=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m +CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +CONFIG_IP_VS=m +CONFIG_IP_VS_IPV6=y +# CONFIG_IP_VS_DEBUG is not set +CONFIG_IP_VS_TAB_BITS=12 + +# +# IPVS transport protocol load balancing support +# +CONFIG_IP_VS_PROTO_TCP=y +CONFIG_IP_VS_PROTO_UDP=y +CONFIG_IP_VS_PROTO_AH_ESP=y +CONFIG_IP_VS_PROTO_ESP=y +CONFIG_IP_VS_PROTO_AH=y + +# +# IPVS scheduler +# +CONFIG_IP_VS_RR=m +CONFIG_IP_VS_WRR=m +CONFIG_IP_VS_LC=m +CONFIG_IP_VS_WLC=m +CONFIG_IP_VS_LBLC=m +CONFIG_IP_VS_LBLCR=m +CONFIG_IP_VS_DH=m +CONFIG_IP_VS_SH=m +CONFIG_IP_VS_SED=m +CONFIG_IP_VS_NQ=m + +# +# IPVS application helper +# +CONFIG_IP_VS_FTP=m # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_IPRANGE=m -CONFIG_IP_NF_MATCH_TOS=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_OWNER=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -426,11 +483,13 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m -CONFIG_IP_NF_TARGET_SAME=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m +CONFIG_NF_NAT_PROTO_DCCP=m CONFIG_NF_NAT_PROTO_GRE=m +CONFIG_NF_NAT_PROTO_UDPLITE=m +CONFIG_NF_NAT_PROTO_SCTP=m CONFIG_NF_NAT_FTP=m CONFIG_NF_NAT_IRC=m CONFIG_NF_NAT_TFTP=m @@ -439,32 +498,30 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m -CONFIG_IP_NF_TARGET_TOS=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m CONFIG_IP_NF_ARP_MANGLE=m # -# IPv6: Netfilter Configuration (EXPERIMENTAL) +# IPv6: Netfilter Configuration # CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m -CONFIG_IP6_NF_MATCH_OWNER=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m @@ -479,6 +536,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -488,12 +546,7 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# CONFIG_NET_SCHED=y -CONFIG_NET_SCH_FIFO=y # # Queueing/Scheduling @@ -502,7 +555,7 @@ CONFIG_NET_SCH_CBQ=m CONFIG_NET_SCH_HTB=m CONFIG_NET_SCH_HFSC=m CONFIG_NET_SCH_PRIO=m -CONFIG_NET_SCH_RR=m +# CONFIG_NET_SCH_MULTIQ is not set CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m @@ -526,6 +579,7 @@ CONFIG_NET_CLS_U32=m # CONFIG_CLS_U32_MARK is not set CONFIG_NET_CLS_RSVP=m CONFIG_NET_CLS_RSVP6=m +CONFIG_NET_CLS_FLOW=m # CONFIG_NET_EMATCH is not set CONFIG_NET_CLS_ACT=y CONFIG_NET_ACT_POLICE=y @@ -533,35 +587,28 @@ CONFIG_NET_ACT_GACT=m CONFIG_GACT_PROB=y CONFIG_NET_ACT_MIRRED=m CONFIG_NET_ACT_IPT=m +CONFIG_NET_ACT_NAT=m CONFIG_NET_ACT_PEDIT=m CONFIG_NET_ACT_SIMP=m -CONFIG_NET_CLS_POLICE=y +CONFIG_NET_ACT_SKBEDIT=m # CONFIG_NET_CLS_IND is not set +CONFIG_NET_SCH_FIFO=y # # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set +CONFIG_PHONET=m CONFIG_FIB_RULES=y - -# -# Wireless -# -CONFIG_CFG80211=m +# CONFIG_WIRELESS is not set CONFIG_WIRELESS_EXT=y -CONFIG_MAC80211=m -# CONFIG_MAC80211_DEBUG is not set CONFIG_IEEE80211=m -# CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m -CONFIG_IEEE80211_CRYPT_CCMP=m -CONFIG_IEEE80211_CRYPT_TKIP=m -CONFIG_IEEE80211_SOFTMAC=m -# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set CONFIG_RFKILL=m CONFIG_RFKILL_INPUT=m # CONFIG_NET_9P is not set @@ -588,7 +635,9 @@ CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set CONFIG_ATA_OVER_ETH=m +# CONFIG_BLK_DEV_HD is not set # CONFIG_MISC_DEVICES is not set +CONFIG_HAVE_IDE=y # CONFIG_IDE is not set # @@ -628,20 +677,22 @@ CONFIG_SCSI_SPI_ATTRS=m # CONFIG_SCSI_FC_ATTRS is not set CONFIG_SCSI_ISCSI_ATTRS=m # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y CONFIG_ISCSI_TCP=m CONFIG_SGIWD93_SCSI=y # CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set # CONFIG_ATA is not set # CONFIG_MD is not set CONFIG_NETDEVICES=y -# CONFIG_NETDEVICES_MULTIQUEUE is not set # CONFIG_IFB is not set CONFIG_DUMMY=m CONFIG_BONDING=m CONFIG_MACVLAN=m CONFIG_EQUALIZER=m CONFIG_TUN=m +CONFIG_VETH=m CONFIG_PHYLIB=m # @@ -656,11 +707,21 @@ CONFIG_CICADA_PHY=m # CONFIG_SMSC_PHY is not set # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set -# CONFIG_FIXED_PHY is not set +CONFIG_REALTEK_PHY=m +CONFIG_MDIO_BITBANG=m CONFIG_NET_ETHERNET=y -# CONFIG_MII is not set +CONFIG_MII=m # CONFIG_AX88796 is not set +CONFIG_SMC91X=m # CONFIG_DM9000 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set +# CONFIG_B44 is not set CONFIG_SGISEEQ=y # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -672,12 +733,12 @@ CONFIG_WLAN_PRE80211=y CONFIG_STRIP=m CONFIG_WLAN_80211=y # CONFIG_LIBERTAS is not set +# CONFIG_IWLWIFI_LEDS is not set CONFIG_HOSTAP=m # CONFIG_HOSTAP_FIRMWARE is not set # CONFIG_WAN is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set -# CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set @@ -699,7 +760,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -720,6 +780,7 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y # CONFIG_MOUSE_PS2_SYNAPTICS is not set # CONFIG_MOUSE_PS2_LIFEBOOK is not set CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set CONFIG_MOUSE_SERIAL=m # CONFIG_MOUSE_VSXXXAA is not set @@ -742,9 +803,11 @@ CONFIG_SERIO_RAW=m # Character devices # CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set # @@ -761,6 +824,17 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set +# CONFIG_HW_RANDOM is not set +# CONFIG_R3964 is not set +CONFIG_RAW_DRIVER=m +CONFIG_MAX_RAW_DEVS=256 +# CONFIG_TCG_TPM is not set +# CONFIG_I2C is not set +# CONFIG_SPI is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +# CONFIG_HWMON is not set +CONFIG_THERMAL=m CONFIG_WATCHDOG=y # CONFIG_WATCHDOG_NOWAYOUT is not set @@ -769,47 +843,50 @@ CONFIG_WATCHDOG=y # # CONFIG_SOFT_WATCHDOG is not set CONFIG_INDYDOG=m -# CONFIG_HW_RANDOM is not set -# CONFIG_RTC is not set -# CONFIG_R3964 is not set -CONFIG_RAW_DRIVER=m -CONFIG_MAX_RAW_DEVS=256 -# CONFIG_TCG_TPM is not set -# CONFIG_I2C is not set +CONFIG_SSB_POSSIBLE=y # -# SPI support +# Sonics Silicon Backplane # -# CONFIG_SPI is not set -# CONFIG_SPI_MASTER is not set -# CONFIG_W1 is not set -# CONFIG_POWER_SUPPLY is not set -# CONFIG_HWMON is not set +# CONFIG_SSB is not set # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices # + +# +# Multimedia core support +# # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# # CONFIG_DAB is not set # # Graphics support # +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set # # Console display driver support @@ -823,48 +900,77 @@ CONFIG_LOGO=y # CONFIG_LOGO_LINUX_VGA16 is not set # CONFIG_LOGO_LINUX_CLUT224 is not set CONFIG_LOGO_SGI_CLUT224=y - -# -# Sound -# # CONFIG_SOUND is not set CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +CONFIG_HIDRAW=y +CONFIG_HID_PID=y + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y CONFIG_USB_SUPPORT=y # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set # CONFIG_USB_ARCH_HAS_EHCI is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set # -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# Enable Host or Gadget support to see Inventra options # # -# USB Gadget Support +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; # # CONFIG_USB_GADGET is not set # CONFIG_MMC is not set +# CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set -# CONFIG_RTC_CLASS is not set +# CONFIG_ACCESSIBILITY is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set # -# DMA Engine support +# RTC interfaces # -# CONFIG_DMA_ENGINE is not set +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +CONFIG_RTC_INTF_DEV_UIE_EMUL=y +# CONFIG_RTC_DRV_TEST is not set # -# DMA Clients +# SPI RTC drivers # # -# DMA Devices +# Platform RTC drivers # +# CONFIG_RTC_DRV_CMOS is not set +CONFIG_RTC_DRV_DS1286=y +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_V3020 is not set # -# Userspace I/O +# on-CPU RTC drivers # +# CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -876,29 +982,33 @@ CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y -# CONFIG_EXT4DEV_FS is not set +CONFIG_EXT4_FS=m +CONFIG_EXT4DEV_COMPAT=y +CONFIG_EXT4_FS_XATTR=y +CONFIG_EXT4_FS_POSIX_ACL=y +CONFIG_EXT4_FS_SECURITY=y CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set +CONFIG_JBD2=m CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m CONFIG_XFS_QUOTA=y -CONFIG_XFS_SECURITY=y # CONFIG_XFS_POSIX_ACL is not set # CONFIG_XFS_RT is not set -# CONFIG_GFS2_FS is not set +# CONFIG_XFS_DEBUG is not set # CONFIG_OCFS2_FS is not set -CONFIG_MINIX_FS=m -# CONFIG_ROMFS_FS is not set +CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y CONFIG_QUOTA=y +CONFIG_QUOTA_NETLINK_INTERFACE=y +# CONFIG_PRINT_QUOTA_WARNING is not set # CONFIG_QFMT_V1 is not set CONFIG_QFMT_V2=m CONFIG_QUOTACTL=y -CONFIG_DNOTIFY=y CONFIG_AUTOFS_FS=m CONFIG_AUTOFS4_FS=m CONFIG_FUSE_FS=m @@ -929,11 +1039,11 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y CONFIG_CONFIGFS_FS=m # @@ -949,27 +1059,25 @@ CONFIG_CONFIGFS_FS=m CONFIG_EFS_FS=m # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set +CONFIG_MINIX_FS=m +CONFIG_OMFS_FS=m # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set CONFIG_UFS_FS=m # CONFIG_UFS_FS_WRITE is not set # CONFIG_UFS_DEBUG is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=m CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y # CONFIG_NFS_V4 is not set -# CONFIG_NFS_DIRECTIO is not set CONFIG_NFSD=m CONFIG_NFSD_V2_ACL=y CONFIG_NFSD_V3=y CONFIG_NFSD_V3_ACL=y # CONFIG_NFSD_V4 is not set -CONFIG_NFSD_TCP=y CONFIG_LOCKD=m CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=m @@ -977,7 +1085,7 @@ CONFIG_NFS_ACL_SUPPORT=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=m CONFIG_SUNRPC_GSS=m -# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=m # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -986,12 +1094,12 @@ CONFIG_SMB_NLS_REMOTE="cp437" CONFIG_CIFS=m # CONFIG_CIFS_STATS is not set # CONFIG_CIFS_WEAK_PW_HASH is not set +CONFIG_CIFS_UPCALL=y # CONFIG_CIFS_XATTR is not set # CONFIG_CIFS_DEBUG2 is not set # CONFIG_CIFS_EXPERIMENTAL is not set # CONFIG_NCP_FS is not set CONFIG_CODA_FS=m -# CONFIG_CODA_FS_OLD_API is not set # CONFIG_AFS_FS is not set # @@ -1015,10 +1123,6 @@ CONFIG_SGI_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=m CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=m @@ -1059,30 +1163,32 @@ CONFIG_NLS_ISO8859_15=m CONFIG_NLS_KOI8_R=m CONFIG_NLS_KOI8_U=m CONFIG_NLS_UTF8=m - -# -# Distributed Lock Manager -# CONFIG_DLM=m # CONFIG_DLM_DEBUG is not set # -# Profiling support -# -# CONFIG_PROFILING is not set - -# # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set -CONFIG_CROSSCOMPILE=y +CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_SYSCTL_SYSCALL_CHECK is not set + +# +# Tracers +# +CONFIG_DYNAMIC_PRINTK_DEBUG=y +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y CONFIG_CMDLINE="" # @@ -1091,46 +1197,97 @@ CONFIG_CMDLINE="" CONFIG_KEYS=y CONFIG_KEYS_DEBUG_PROC_KEYS=y # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +CONFIG_SECURITY_FILE_CAPABILITIES=y CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_FIPS=y CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_ABLKCIPHER=m -CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_AEAD=y +CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_GF128MUL=m +CONFIG_CRYPTO_NULL=m +CONFIG_CRYPTO_CRYPTD=m +CONFIG_CRYPTO_AUTHENC=m +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +CONFIG_CRYPTO_CCM=m +CONFIG_CRYPTO_GCM=m +CONFIG_CRYPTO_SEQIV=m + +# +# Block modes +# +CONFIG_CRYPTO_CBC=m +CONFIG_CRYPTO_CTR=m +CONFIG_CRYPTO_CTS=m +CONFIG_CRYPTO_ECB=m +CONFIG_CRYPTO_LRW=m +CONFIG_CRYPTO_PCBC=m +CONFIG_CRYPTO_XTS=m + +# +# Hash modes +# CONFIG_CRYPTO_HMAC=y CONFIG_CRYPTO_XCBC=m -CONFIG_CRYPTO_NULL=m + +# +# Digest +# +CONFIG_CRYPTO_CRC32C=m CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=y +CONFIG_CRYPTO_MICHAEL_MIC=m +CONFIG_CRYPTO_RMD128=m +CONFIG_CRYPTO_RMD160=m +CONFIG_CRYPTO_RMD256=m +CONFIG_CRYPTO_RMD320=m CONFIG_CRYPTO_SHA1=m CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m -CONFIG_CRYPTO_WP512=m CONFIG_CRYPTO_TGR192=m -CONFIG_CRYPTO_GF128MUL=m -CONFIG_CRYPTO_ECB=m -CONFIG_CRYPTO_CBC=m -CONFIG_CRYPTO_PCBC=m -CONFIG_CRYPTO_LRW=m -CONFIG_CRYPTO_CRYPTD=m -CONFIG_CRYPTO_DES=m -CONFIG_CRYPTO_FCRYPT=m -CONFIG_CRYPTO_BLOWFISH=m -CONFIG_CRYPTO_TWOFISH=m -CONFIG_CRYPTO_TWOFISH_COMMON=m -CONFIG_CRYPTO_SERPENT=m +CONFIG_CRYPTO_WP512=m + +# +# Ciphers +# CONFIG_CRYPTO_AES=m +CONFIG_CRYPTO_ANUBIS=m +CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_BLOWFISH=m +CONFIG_CRYPTO_CAMELLIA=m CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m -CONFIG_CRYPTO_TEA=m -CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_DES=m +CONFIG_CRYPTO_FCRYPT=m CONFIG_CRYPTO_KHAZAD=m -CONFIG_CRYPTO_ANUBIS=m +CONFIG_CRYPTO_SALSA20=m +CONFIG_CRYPTO_SEED=m +CONFIG_CRYPTO_SERPENT=m +CONFIG_CRYPTO_TEA=m +CONFIG_CRYPTO_TWOFISH=m +CONFIG_CRYPTO_TWOFISH_COMMON=m + +# +# Compression +# CONFIG_CRYPTO_DEFLATE=m -CONFIG_CRYPTO_MICHAEL_MIC=m -CONFIG_CRYPTO_CRC32C=m -CONFIG_CRYPTO_CAMELLIA=m -# CONFIG_CRYPTO_TEST is not set +CONFIG_CRYPTO_LZO=m + +# +# Random Number Generation +# +CONFIG_CRYPTO_ANSI_CPRNG=m # CONFIG_CRYPTO_HW is not set # @@ -1139,12 +1296,15 @@ CONFIG_CRYPTO_CAMELLIA=m CONFIG_BITREVERSE=m # CONFIG_CRC_CCITT is not set CONFIG_CRC16=m -# CONFIG_CRC_ITU_T is not set +CONFIG_CRC_T10DIF=m +CONFIG_CRC_ITU_T=m CONFIG_CRC32=m # CONFIG_CRC7 is not set CONFIG_LIBCRC32C=m CONFIG_ZLIB_INFLATE=m CONFIG_ZLIB_DEFLATE=m +CONFIG_LZO_COMPRESS=m +CONFIG_LZO_DECOMPRESS=m CONFIG_TEXTSEARCH=y CONFIG_TEXTSEARCH_KMP=m CONFIG_TEXTSEARCH_BM=m diff --git a/arch/mips/configs/malta_defconfig b/arch/mips/configs/malta_defconfig index a699565..1ecdd3b 100644 --- a/arch/mips/configs/malta_defconfig +++ b/arch/mips/configs/malta_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc2 -# Tue Aug 7 12:59:29 2007 +# Linux kernel version: 2.6.28-rc6 +# Mon Dec 1 08:08:19 2008 # CONFIG_MIPS=y @@ -11,20 +11,25 @@ CONFIG_MIPS=y CONFIG_ZONE_DMA=y # CONFIG_MACH_ALCHEMY is not set # CONFIG_BASLER_EXCITE is not set +# CONFIG_BCM47XX is not set # CONFIG_MIPS_COBALT is not set # CONFIG_MACH_DECSTATION is not set # CONFIG_MACH_JAZZ is not set +# CONFIG_LASAT is not set # CONFIG_LEMOTE_FULONG is not set CONFIG_MIPS_MALTA=y # CONFIG_MIPS_SIM is not set -# CONFIG_MARKEINS is not set +# CONFIG_MACH_EMMA is not set # CONFIG_MACH_VR41XX is not set +# CONFIG_NXP_STB220 is not set +# CONFIG_NXP_STB225 is not set # CONFIG_PNX8550_JBS is not set # CONFIG_PNX8550_STB810 is not set # CONFIG_PMC_MSP is not set # CONFIG_PMC_YOSEMITE is not set # CONFIG_SGI_IP22 is not set # CONFIG_SGI_IP27 is not set +# CONFIG_SGI_IP28 is not set # CONFIG_SGI_IP32 is not set # CONFIG_SIBYTE_CRHINE is not set # CONFIG_SIBYTE_CARMEL is not set @@ -35,13 +40,14 @@ CONFIG_MIPS_MALTA=y # CONFIG_SIBYTE_SENTOSA is not set # CONFIG_SIBYTE_BIGSUR is not set # CONFIG_SNI_RM is not set -# CONFIG_TOSHIBA_JMR3927 is not set -# CONFIG_TOSHIBA_RBTX4927 is not set -# CONFIG_TOSHIBA_RBTX4938 is not set +# CONFIG_MACH_TX39XX is not set +# CONFIG_MACH_TX49XX is not set +# CONFIG_MIKROTIK_RB532 is not set # CONFIG_WR_PPMC is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U32 is not set # CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_ARCH_SUPPORTS_OPROFILE=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y @@ -51,21 +57,26 @@ CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y # CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set CONFIG_ARCH_MAY_HAVE_PC_FDC=y +CONFIG_BOOT_RAW=y CONFIG_CEVT_R4K=y +CONFIG_CSRC_R4K=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y CONFIG_EARLY_PRINTK=y CONFIG_SYS_HAS_EARLY_PRINTK=y -CONFIG_GENERIC_ISA_DMA=y +# CONFIG_HOTPLUG_CPU is not set CONFIG_I8259=y CONFIG_MIPS_BONITO64=y CONFIG_MIPS_MSC=y # CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_ISA_DMA=y # CONFIG_CPU_BIG_ENDIAN is not set CONFIG_CPU_LITTLE_ENDIAN=y CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y CONFIG_IRQ_CPU=y +CONFIG_IRQ_GIC=y +CONFIG_MIPS_BOARDS_GEN=y CONFIG_PCI_GT64XXX_PCI0=y CONFIG_SWAP_IO_SPACE=y CONFIG_BOOT_ELF32=y @@ -74,10 +85,6 @@ CONFIG_MIPS_L1_CACHE_SHIFT=5 # # CPU selection # -CONFIG_TICK_ONESHOT=y -CONFIG_NO_HZ=y -CONFIG_HIGH_RES_TIMERS=y -CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_CPU_LOONGSON2 is not set # CONFIG_CPU_MIPS32_R1 is not set CONFIG_CPU_MIPS32_R2=y @@ -91,6 +98,7 @@ CONFIG_CPU_MIPS32_R2=y # CONFIG_CPU_TX49XX is not set # CONFIG_CPU_R5000 is not set # CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R5500 is not set # CONFIG_CPU_R6000 is not set # CONFIG_CPU_NEVADA is not set # CONFIG_CPU_R8000 is not set @@ -108,6 +116,7 @@ CONFIG_CPU_MIPSR2=y CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y CONFIG_SYS_SUPPORTS_64BIT_KERNEL=y CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_HARDWARE_WATCHPOINTS=y # # Kernel type @@ -125,6 +134,8 @@ CONFIG_CPU_HAS_PREFETCH=y CONFIG_MIPS_MT_SMP=y # CONFIG_MIPS_MT_SMTC is not set CONFIG_MIPS_MT=y +# CONFIG_SCHED_SMT is not set +CONFIG_SYS_SUPPORTS_SCHED_SMT=y CONFIG_SYS_SUPPORTS_MULTITHREADING=y CONFIG_MIPS_MT_FPAFF=y # CONFIG_MIPS_VPE_LOADER is not set @@ -132,7 +143,6 @@ CONFIG_CPU_HAS_LLSC=y # CONFIG_CPU_HAS_SMARTMIPS is not set CONFIG_CPU_MIPSR2_IRQ_VI=y CONFIG_CPU_MIPSR2_IRQ_EI=y -CONFIG_CPU_MIPSR2_SRS=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y @@ -140,22 +150,30 @@ CONFIG_IRQ_PER_CPU=y CONFIG_CPU_SUPPORTS_HIGHMEM=y CONFIG_SYS_SUPPORTS_SMARTMIPS=y CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y CONFIG_SMP=y +CONFIG_SMP_UP=y CONFIG_SYS_SUPPORTS_SMP=y CONFIG_NR_CPUS_DEFAULT_2=y CONFIG_NR_CPUS=2 +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_48 is not set CONFIG_HZ_100=y # CONFIG_HZ_128 is not set @@ -168,7 +186,6 @@ CONFIG_HZ=100 CONFIG_PREEMPT_NONE=y # CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set -CONFIG_PREEMPT_BKL=y # CONFIG_KEXEC is not set CONFIG_SECCOMP=y CONFIG_LOCKDEP_SUPPORT=y @@ -189,13 +206,19 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_POSIX_MQUEUE is not set # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set -# CONFIG_USER_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=15 -# CONFIG_CPUSETS is not set +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y CONFIG_RELAY=y +CONFIG_NAMESPACES=y +CONFIG_UTS_NS=y +CONFIG_IPC_NS=y +# CONFIG_USER_NS is not set +CONFIG_PID_NS=y # CONFIG_BLK_DEV_INITRD is not set # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set CONFIG_SYSCTL=y @@ -207,6 +230,8 @@ CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y +CONFIG_PCSPKR_PLATFORM=y +# CONFIG_COMPAT_BRK is not set CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_ANON_INODES=y @@ -215,14 +240,23 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y +CONFIG_PCI_QUIRKS=y CONFIG_SLAB=y # CONFIG_SLUB is not set # CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +CONFIG_USE_GENERIC_SMP_HELPERS=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_MODVERSIONS=y @@ -234,6 +268,7 @@ CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_LSF is not set # CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set # # IO Schedulers @@ -247,19 +282,19 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Bus options (PCI, PCMCIA, EISA, ISA, TC) # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y # CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_PCI_LEGACY=y CONFIG_MMU=y CONFIG_I8253=y - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -267,6 +302,8 @@ CONFIG_I8253=y # Executable file formats # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set CONFIG_TRAD_SIGNALS=y @@ -274,12 +311,7 @@ CONFIG_TRAD_SIGNALS=y # Power management options # CONFIG_PM=y -# CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set - -# -# Networking -# CONFIG_NET=y # @@ -292,6 +324,8 @@ CONFIG_XFRM=y CONFIG_XFRM_USER=m # CONFIG_XFRM_SUB_POLICY is not set CONFIG_XFRM_MIGRATE=y +# CONFIG_XFRM_STATISTICS is not set +CONFIG_XFRM_IPCOMP=m CONFIG_NET_KEY=y CONFIG_NET_KEY_MIGRATE=y CONFIG_INET=y @@ -323,42 +357,13 @@ CONFIG_INET_TUNNEL=m CONFIG_INET_XFRM_MODE_TRANSPORT=m CONFIG_INET_XFRM_MODE_TUNNEL=m CONFIG_INET_XFRM_MODE_BEET=y +CONFIG_INET_LRO=m CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y CONFIG_DEFAULT_TCP_CONG="cubic" CONFIG_TCP_MD5SIG=y -CONFIG_IP_VS=m -# CONFIG_IP_VS_DEBUG is not set -CONFIG_IP_VS_TAB_BITS=12 - -# -# IPVS transport protocol load balancing support -# -CONFIG_IP_VS_PROTO_TCP=y -CONFIG_IP_VS_PROTO_UDP=y -CONFIG_IP_VS_PROTO_ESP=y -CONFIG_IP_VS_PROTO_AH=y - -# -# IPVS scheduler -# -CONFIG_IP_VS_RR=m -CONFIG_IP_VS_WRR=m -CONFIG_IP_VS_LC=m -CONFIG_IP_VS_WLC=m -CONFIG_IP_VS_LBLC=m -CONFIG_IP_VS_LBLCR=m -CONFIG_IP_VS_DH=m -CONFIG_IP_VS_SH=m -CONFIG_IP_VS_SED=m -CONFIG_IP_VS_NQ=m - -# -# IPVS application helper -# -CONFIG_IP_VS_FTP=m CONFIG_IPV6=m CONFIG_IPV6_PRIVACY=y CONFIG_IPV6_ROUTER_PREF=y @@ -375,11 +380,15 @@ CONFIG_INET6_XFRM_MODE_TUNNEL=m CONFIG_INET6_XFRM_MODE_BEET=m # CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set CONFIG_IPV6_SIT=m +CONFIG_IPV6_NDISC_NODETYPE=y CONFIG_IPV6_TUNNEL=m # CONFIG_IPV6_MULTIPLE_TABLES is not set +CONFIG_IPV6_MROUTE=y +CONFIG_IPV6_PIMSM_V2=y CONFIG_NETWORK_SECMARK=y CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set +CONFIG_NETFILTER_ADVANCED=y CONFIG_BRIDGE_NETFILTER=y # @@ -388,12 +397,12 @@ CONFIG_BRIDGE_NETFILTER=y CONFIG_NETFILTER_NETLINK=m CONFIG_NETFILTER_NETLINK_QUEUE=m CONFIG_NETFILTER_NETLINK_LOG=m -CONFIG_NF_CONNTRACK_ENABLED=m CONFIG_NF_CONNTRACK=m CONFIG_NF_CT_ACCT=y CONFIG_NF_CONNTRACK_MARK=y CONFIG_NF_CONNTRACK_SECMARK=y CONFIG_NF_CONNTRACK_EVENTS=y +CONFIG_NF_CT_PROTO_DCCP=m CONFIG_NF_CT_PROTO_GRE=m CONFIG_NF_CT_PROTO_SCTP=m CONFIG_NF_CT_PROTO_UDPLITE=m @@ -407,18 +416,22 @@ CONFIG_NF_CONNTRACK_SANE=m CONFIG_NF_CONNTRACK_SIP=m CONFIG_NF_CONNTRACK_TFTP=m CONFIG_NF_CT_NETLINK=m +CONFIG_NETFILTER_TPROXY=m CONFIG_NETFILTER_XTABLES=m CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m CONFIG_NETFILTER_XT_TARGET_CONNMARK=m +# CONFIG_NETFILTER_XT_TARGET_CONNSECMARK is not set # CONFIG_NETFILTER_XT_TARGET_DSCP is not set CONFIG_NETFILTER_XT_TARGET_MARK=m -CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NFLOG=m +CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m CONFIG_NETFILTER_XT_TARGET_NOTRACK=m +CONFIG_NETFILTER_XT_TARGET_RATEEST=m +CONFIG_NETFILTER_XT_TARGET_TPROXY=m CONFIG_NETFILTER_XT_TARGET_TRACE=m CONFIG_NETFILTER_XT_TARGET_SECMARK=m -# CONFIG_NETFILTER_XT_TARGET_CONNSECMARK is not set CONFIG_NETFILTER_XT_TARGET_TCPMSS=m +CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m CONFIG_NETFILTER_XT_MATCH_COMMENT=m CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m @@ -427,40 +440,76 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m CONFIG_NETFILTER_XT_MATCH_DCCP=m # CONFIG_NETFILTER_XT_MATCH_DSCP is not set CONFIG_NETFILTER_XT_MATCH_ESP=m +CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m CONFIG_NETFILTER_XT_MATCH_HELPER=m +CONFIG_NETFILTER_XT_MATCH_IPRANGE=m CONFIG_NETFILTER_XT_MATCH_LENGTH=m CONFIG_NETFILTER_XT_MATCH_LIMIT=m CONFIG_NETFILTER_XT_MATCH_MAC=m CONFIG_NETFILTER_XT_MATCH_MARK=m -CONFIG_NETFILTER_XT_MATCH_POLICY=m CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m +CONFIG_NETFILTER_XT_MATCH_OWNER=m +CONFIG_NETFILTER_XT_MATCH_POLICY=m # CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m CONFIG_NETFILTER_XT_MATCH_QUOTA=m +CONFIG_NETFILTER_XT_MATCH_RATEEST=m CONFIG_NETFILTER_XT_MATCH_REALM=m +CONFIG_NETFILTER_XT_MATCH_RECENT=m +# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set CONFIG_NETFILTER_XT_MATCH_SCTP=m +CONFIG_NETFILTER_XT_MATCH_SOCKET=m CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m +CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m -CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m +CONFIG_IP_VS=m +CONFIG_IP_VS_IPV6=y +# CONFIG_IP_VS_DEBUG is not set +CONFIG_IP_VS_TAB_BITS=12 + +# +# IPVS transport protocol load balancing support +# +CONFIG_IP_VS_PROTO_TCP=y +CONFIG_IP_VS_PROTO_UDP=y +CONFIG_IP_VS_PROTO_AH_ESP=y +CONFIG_IP_VS_PROTO_ESP=y +CONFIG_IP_VS_PROTO_AH=y + +# +# IPVS scheduler +# +CONFIG_IP_VS_RR=m +CONFIG_IP_VS_WRR=m +CONFIG_IP_VS_LC=m +CONFIG_IP_VS_WLC=m +CONFIG_IP_VS_LBLC=m +CONFIG_IP_VS_LBLCR=m +CONFIG_IP_VS_DH=m +CONFIG_IP_VS_SH=m +CONFIG_IP_VS_SED=m +CONFIG_IP_VS_NQ=m + +# +# IPVS application helper +# +CONFIG_IP_VS_FTP=m # # IP: Netfilter Configuration # +CONFIG_NF_DEFRAG_IPV4=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_PROC_COMPAT=y CONFIG_IP_NF_QUEUE=m CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_IPRANGE=m -CONFIG_IP_NF_MATCH_TOS=m -CONFIG_IP_NF_MATCH_RECENT=m -CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_MATCH_AH=m +CONFIG_IP_NF_MATCH_ECN=m CONFIG_IP_NF_MATCH_TTL=m -CONFIG_IP_NF_MATCH_OWNER=m -CONFIG_IP_NF_MATCH_ADDRTYPE=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m CONFIG_IP_NF_TARGET_LOG=m @@ -468,11 +517,13 @@ CONFIG_IP_NF_TARGET_ULOG=m CONFIG_NF_NAT=m CONFIG_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_TARGET_NETMAP=m -CONFIG_IP_NF_TARGET_SAME=m +CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_NF_NAT_SNMP_BASIC=m +CONFIG_NF_NAT_PROTO_DCCP=m CONFIG_NF_NAT_PROTO_GRE=m +CONFIG_NF_NAT_PROTO_UDPLITE=m +CONFIG_NF_NAT_PROTO_SCTP=m CONFIG_NF_NAT_FTP=m CONFIG_NF_NAT_IRC=m CONFIG_NF_NAT_TFTP=m @@ -481,40 +532,34 @@ CONFIG_NF_NAT_PPTP=m CONFIG_NF_NAT_H323=m CONFIG_NF_NAT_SIP=m CONFIG_IP_NF_MANGLE=m -CONFIG_IP_NF_TARGET_TOS=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m CONFIG_IP_NF_TARGET_TTL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_RAW=m CONFIG_IP_NF_ARPTABLES=m CONFIG_IP_NF_ARPFILTER=m CONFIG_IP_NF_ARP_MANGLE=m # -# IPv6: Netfilter Configuration (EXPERIMENTAL) +# IPv6: Netfilter Configuration # CONFIG_NF_CONNTRACK_IPV6=m CONFIG_IP6_NF_QUEUE=m CONFIG_IP6_NF_IPTABLES=m -CONFIG_IP6_NF_MATCH_RT=m -CONFIG_IP6_NF_MATCH_OPTS=m +CONFIG_IP6_NF_MATCH_AH=m +CONFIG_IP6_NF_MATCH_EUI64=m CONFIG_IP6_NF_MATCH_FRAG=m +CONFIG_IP6_NF_MATCH_OPTS=m CONFIG_IP6_NF_MATCH_HL=m -CONFIG_IP6_NF_MATCH_OWNER=m CONFIG_IP6_NF_MATCH_IPV6HEADER=m -CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_MH=m -CONFIG_IP6_NF_MATCH_EUI64=m -CONFIG_IP6_NF_FILTER=m +CONFIG_IP6_NF_MATCH_RT=m CONFIG_IP6_NF_TARGET_LOG=m +CONFIG_IP6_NF_FILTER=m CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_TARGET_HL=m CONFIG_IP6_NF_RAW=m - -# -# Bridge: Netfilter Configuration -# CONFIG_BRIDGE_NF_EBTABLES=m CONFIG_BRIDGE_EBT_BROUTE=m CONFIG_BRIDGE_EBT_T_FILTER=m @@ -523,6 +568,7 @@ CONFIG_BRIDGE_EBT_802_3=m CONFIG_BRIDGE_EBT_AMONG=m CONFIG_BRIDGE_EBT_ARP=m CONFIG_BRIDGE_EBT_IP=m +CONFIG_BRIDGE_EBT_IP6=m CONFIG_BRIDGE_EBT_LIMIT=m CONFIG_BRIDGE_EBT_MARK=m CONFIG_BRIDGE_EBT_PKTTYPE=m @@ -535,6 +581,7 @@ CONFIG_BRIDGE_EBT_REDIRECT=m CONFIG_BRIDGE_EBT_SNAT=m CONFIG_BRIDGE_EBT_LOG=m CONFIG_BRIDGE_EBT_ULOG=m +CONFIG_BRIDGE_EBT_NFLOG=m # CONFIG_IP_DCCP is not set CONFIG_IP_SCTP=m # CONFIG_SCTP_DBG_MSG is not set @@ -544,8 +591,12 @@ CONFIG_IP_SCTP=m CONFIG_SCTP_HMAC_MD5=y # CONFIG_TIPC is not set # CONFIG_ATM is not set +CONFIG_STP=m +CONFIG_GARP=m CONFIG_BRIDGE=m +# CONFIG_NET_DSA is not set CONFIG_VLAN_8021Q=m +CONFIG_VLAN_8021Q_GVRP=y # CONFIG_DECNET is not set CONFIG_LLC=m # CONFIG_LLC2 is not set @@ -559,12 +610,7 @@ CONFIG_IPDDP_DECAP=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# CONFIG_NET_SCHED=y -CONFIG_NET_SCH_FIFO=y # # Queueing/Scheduling @@ -573,7 +619,7 @@ CONFIG_NET_SCH_CBQ=m CONFIG_NET_SCH_HTB=m CONFIG_NET_SCH_HFSC=m CONFIG_NET_SCH_PRIO=m -CONFIG_NET_SCH_RR=m +# CONFIG_NET_SCH_MULTIQ is not set CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m CONFIG_NET_SCH_TEQL=m @@ -597,6 +643,7 @@ CONFIG_NET_CLS_U32=m # CONFIG_CLS_U32_MARK is not set CONFIG_NET_CLS_RSVP=m CONFIG_NET_CLS_RSVP6=m +CONFIG_NET_CLS_FLOW=m # CONFIG_NET_EMATCH is not set CONFIG_NET_CLS_ACT=y CONFIG_NET_ACT_POLICE=y @@ -604,37 +651,51 @@ CONFIG_NET_ACT_GACT=m CONFIG_GACT_PROB=y CONFIG_NET_ACT_MIRRED=m CONFIG_NET_ACT_IPT=m +CONFIG_NET_ACT_NAT=m CONFIG_NET_ACT_PEDIT=m CONFIG_NET_ACT_SIMP=m -CONFIG_NET_CLS_POLICE=y +CONFIG_NET_ACT_SKBEDIT=m CONFIG_NET_CLS_IND=y +CONFIG_NET_SCH_FIFO=y # # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set +CONFIG_PHONET=m CONFIG_FIB_RULES=y - -# -# Wireless -# +CONFIG_WIRELESS=y CONFIG_CFG80211=m +CONFIG_NL80211=y +CONFIG_WIRELESS_OLD_REGULATORY=y CONFIG_WIRELESS_EXT=y +CONFIG_WIRELESS_EXT_SYSFS=y CONFIG_MAC80211=m -# CONFIG_MAC80211_DEBUG is not set + +# +# Rate control algorithm selection +# +CONFIG_MAC80211_RC_PID=y +CONFIG_MAC80211_RC_MINSTREL=y +CONFIG_MAC80211_RC_DEFAULT_PID=y +# CONFIG_MAC80211_RC_DEFAULT_MINSTREL is not set +CONFIG_MAC80211_RC_DEFAULT="pid" +CONFIG_MAC80211_MESH=y +CONFIG_MAC80211_LEDS=y +# CONFIG_MAC80211_DEBUG_MENU is not set CONFIG_IEEE80211=m # CONFIG_IEEE80211_DEBUG is not set CONFIG_IEEE80211_CRYPT_WEP=m CONFIG_IEEE80211_CRYPT_CCMP=m CONFIG_IEEE80211_CRYPT_TKIP=m -CONFIG_IEEE80211_SOFTMAC=m -# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set CONFIG_RFKILL=m CONFIG_RFKILL_INPUT=m +CONFIG_RFKILL_LEDS=y # CONFIG_NET_9P is not set # @@ -644,9 +705,12 @@ CONFIG_RFKILL_INPUT=m # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" # CONFIG_SYS_HYPERVISOR is not set CONFIG_CONNECTOR=m CONFIG_MTD=y @@ -655,6 +719,7 @@ CONFIG_MTD=y CONFIG_MTD_PARTITIONS=y # CONFIG_MTD_REDBOOT_PARTS is not set # CONFIG_MTD_CMDLINE_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set # # User Modules And Translation Layers @@ -667,6 +732,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +CONFIG_MTD_OOPS=m # # RAM/ROM/Flash chip drivers @@ -701,6 +767,7 @@ CONFIG_MTD_PHYSMAP=y CONFIG_MTD_PHYSMAP_START=0x0 CONFIG_MTD_PHYSMAP_LEN=0x0 CONFIG_MTD_PHYSMAP_BANKWIDTH=0 +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -748,25 +815,26 @@ CONFIG_BLK_DEV_NBD=m CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=4096 -CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_BLK_DEV_XIP is not set CONFIG_CDROM_PKTCDVD=m CONFIG_CDROM_PKTCDVD_BUFFERS=8 # CONFIG_CDROM_PKTCDVD_WCACHE is not set CONFIG_ATA_OVER_ETH=m +# CONFIG_BLK_DEV_HD is not set # CONFIG_MISC_DEVICES is not set +CONFIG_HAVE_IDE=y CONFIG_IDE=y -CONFIG_IDE_MAX_HWIFS=4 -CONFIG_BLK_DEV_IDE=y # -# Please see Documentation/ide.txt for help/info on IDE drives +# Please see Documentation/ide/ide.txt for help/info on IDE drives # # CONFIG_BLK_DEV_IDE_SATA is not set -CONFIG_BLK_DEV_IDEDISK=y -# CONFIG_IDEDISK_MULTI_MODE is not set +CONFIG_IDE_GD=y +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set CONFIG_BLK_DEV_IDECD=y +CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y # CONFIG_BLK_DEV_IDETAPE is not set -# CONFIG_BLK_DEV_IDEFLOPPY is not set # CONFIG_BLK_DEV_IDESCSI is not set # CONFIG_IDE_TASK_IOCTL is not set CONFIG_IDE_PROC_FS=y @@ -775,24 +843,25 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set +CONFIG_BLK_DEV_IDEDMA_SFF=y + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y -# CONFIG_IDEPCI_SHARE_IRQ is not set CONFIG_IDEPCI_PCIBUS_ORDER=y # CONFIG_BLK_DEV_OFFBOARD is not set CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set # CONFIG_BLK_DEV_CMD64X is not set # CONFIG_BLK_DEV_TRIFLEX is not set -# CONFIG_BLK_DEV_CY82C693 is not set # CONFIG_BLK_DEV_CS5520 is not set # CONFIG_BLK_DEV_CS5530 is not set -# CONFIG_BLK_DEV_HPT34X is not set # CONFIG_BLK_DEV_HPT366 is not set # CONFIG_BLK_DEV_JMICRON is not set # CONFIG_BLK_DEV_SC1200 is not set @@ -808,10 +877,7 @@ CONFIG_BLK_DEV_IT8213=m # CONFIG_BLK_DEV_TRM290 is not set # CONFIG_BLK_DEV_VIA82CXXX is not set CONFIG_BLK_DEV_TC86C001=m -# CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set -# CONFIG_BLK_DEV_HD is not set # # SCSI device support @@ -848,8 +914,10 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_SPI_ATTRS=m CONFIG_SCSI_FC_ATTRS=m +# CONFIG_SCSI_FC_TGT_ATTRS is not set CONFIG_SCSI_ISCSI_ATTRS=m # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y CONFIG_ISCSI_TCP=m CONFIG_BLK_DEV_3W_XXXX_RAID=m @@ -866,6 +934,7 @@ CONFIG_AIC7XXX_REG_PRETTY_PRINT=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -876,6 +945,7 @@ CONFIG_AIC7XXX_REG_PRETTY_PRINT=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set @@ -887,6 +957,7 @@ CONFIG_AIC7XXX_REG_PRETTY_PRINT=y # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_SRP is not set +# CONFIG_SCSI_DH is not set # CONFIG_ATA is not set CONFIG_MD=y CONFIG_BLK_DEV_MD=m @@ -905,32 +976,28 @@ CONFIG_DM_SNAPSHOT=m CONFIG_DM_MIRROR=m CONFIG_DM_ZERO=m CONFIG_DM_MULTIPATH=m -CONFIG_DM_MULTIPATH_EMC=m -CONFIG_DM_MULTIPATH_RDAC=m # CONFIG_DM_DELAY is not set +# CONFIG_DM_UEVENT is not set +# CONFIG_FUSION is not set # -# Fusion MPT device support +# IEEE 1394 (FireWire) support # -# CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # -# IEEE 1394 (FireWire) support +# Enable only one of the two stacks, unless you know what you are doing # # CONFIG_FIREWIRE is not set # CONFIG_IEEE1394 is not set # CONFIG_I2O is not set CONFIG_NETDEVICES=y -CONFIG_NETDEVICES_MULTIQUEUE=y CONFIG_IFB=m CONFIG_DUMMY=m CONFIG_BONDING=m CONFIG_MACVLAN=m CONFIG_EQUALIZER=m CONFIG_TUN=m +CONFIG_VETH=m # CONFIG_ARCNET is not set CONFIG_PHYLIB=m @@ -946,26 +1013,34 @@ CONFIG_VITESSE_PHY=m CONFIG_SMSC_PHY=m CONFIG_BROADCOM_PHY=m CONFIG_ICPLUS_PHY=m -# CONFIG_FIXED_PHY is not set +CONFIG_REALTEK_PHY=m +CONFIG_MDIO_BITBANG=m CONFIG_NET_ETHERNET=y CONFIG_MII=y CONFIG_AX88796=m +# CONFIG_AX88796_93CX6 is not set # CONFIG_HAPPYMEAL is not set # CONFIG_SUNGEM is not set # CONFIG_CASSINI is not set # CONFIG_NET_VENDOR_3COM is not set +# CONFIG_SMC91X is not set # CONFIG_DM9000 is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set CONFIG_NET_PCI=y CONFIG_PCNET32=y -# CONFIG_PCNET32_NAPI is not set # CONFIG_AMD8111_ETH is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set CONFIG_TC35815=m -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set # CONFIG_E100 is not set # CONFIG_FEALNX is not set @@ -973,16 +1048,21 @@ CONFIG_TC35815=m # CONFIG_NE2K_PCI is not set # CONFIG_8139CP is not set # CONFIG_8139TOO is not set +# CONFIG_R6040 is not set # CONFIG_SIS900 is not set # CONFIG_EPIC100 is not set # CONFIG_SUNDANCE is not set # CONFIG_TLAN is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set +# CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set +# CONFIG_IP1000 is not set +# CONFIG_IGB is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -995,14 +1075,24 @@ CONFIG_NETDEV_1000=y # CONFIG_BNX2 is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set +# CONFIG_ATL1E is not set +# CONFIG_JME is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set CONFIG_CHELSIO_T3=m +# CONFIG_ENIC is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set CONFIG_NETXEN_NIC=m +# CONFIG_NIU is not set +# CONFIG_MLX4_EN is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set +# CONFIG_BNX2X is not set +# CONFIG_QLGE is not set +# CONFIG_SFC is not set # CONFIG_TR is not set # @@ -1022,6 +1112,7 @@ CONFIG_IPW2200_QOS=y # CONFIG_IPW2200_DEBUG is not set CONFIG_LIBERTAS=m # CONFIG_LIBERTAS_DEBUG is not set +# CONFIG_LIBERTAS_THINFIRM is not set CONFIG_HERMES=m CONFIG_PLX_HERMES=m CONFIG_TMD_HERMES=m @@ -1030,25 +1121,30 @@ CONFIG_PCI_HERMES=m CONFIG_ATMEL=m CONFIG_PCI_ATMEL=m CONFIG_PRISM54=m +# CONFIG_RTL8180 is not set +# CONFIG_ADM8211 is not set +# CONFIG_MAC80211_HWSIM is not set +# CONFIG_P54_COMMON is not set +# CONFIG_ATH5K is not set +# CONFIG_ATH9K is not set +# CONFIG_IWLCORE is not set +# CONFIG_IWLWIFI_LEDS is not set +# CONFIG_IWLAGN is not set +# CONFIG_IWL3945 is not set CONFIG_HOSTAP=m CONFIG_HOSTAP_FIRMWARE=y CONFIG_HOSTAP_FIRMWARE_NVRAM=y CONFIG_HOSTAP_PLX=m CONFIG_HOSTAP_PCI=m -CONFIG_BCM43XX=m -CONFIG_BCM43XX_DEBUG=y -CONFIG_BCM43XX_DMA=y -CONFIG_BCM43XX_PIO=y -CONFIG_BCM43XX_DMA_AND_PIO_MODE=y -# CONFIG_BCM43XX_DMA_MODE is not set -# CONFIG_BCM43XX_PIO_MODE is not set +# CONFIG_B43 is not set +# CONFIG_B43LEGACY is not set +# CONFIG_RT2X00 is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NET_FC is not set -# CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set @@ -1070,7 +1166,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -1099,10 +1194,13 @@ CONFIG_SERIO_SERPORT=y # Character devices # CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y CONFIG_VT_HW_CONSOLE_BINDING=y +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set # # Serial drivers @@ -1124,79 +1222,118 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=m # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y # CONFIG_I2C is not set - -# -# SPI support -# # CONFIG_SPI is not set -# CONFIG_SPI_MASTER is not set # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +# CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y + +# +# Sonics Silicon Backplane +# +# CONFIG_SSB is not set # # Multifunction device drivers # +# CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices # + +# +# Multimedia core support +# # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# # CONFIG_DAB is not set # # Graphics support # +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set # # Console display driver support # # CONFIG_VGA_CONSOLE is not set CONFIG_DUMMY_CONSOLE=y - -# -# Sound -# # CONFIG_SOUND is not set CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set +# CONFIG_HID_PID is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_USB is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set # -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# Enable Host or Gadget support to see Inventra options # # -# USB Gadget Support +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; # # CONFIG_USB_GADGET is not set +# CONFIG_UWB is not set # CONFIG_MMC is not set -# CONFIG_NEW_LEDS is not set +# CONFIG_MEMSTICK is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=m + +# +# LED drivers +# + +# +# LED Triggers +# +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=m +CONFIG_LEDS_TRIGGER_IDE_DISK=y +CONFIG_LEDS_TRIGGER_HEARTBEAT=m +CONFIG_LEDS_TRIGGER_BACKLIGHT=m +CONFIG_LEDS_TRIGGER_DEFAULT_ON=m +# CONFIG_ACCESSIBILITY is not set # CONFIG_INFINIBAND is not set CONFIG_RTC_LIB=y CONFIG_RTC_CLASS=y @@ -1235,25 +1372,15 @@ CONFIG_RTC_DRV_CMOS=y # # on-CPU RTC drivers # - -# -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# -# Userspace I/O -# +# CONFIG_DMADEVICES is not set CONFIG_UIO=m CONFIG_UIO_CIF=m +# CONFIG_UIO_PDRV is not set +# CONFIG_UIO_PDRV_GENIRQ is not set +# CONFIG_UIO_SMX is not set +# CONFIG_UIO_SERCOS3 is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -1265,9 +1392,8 @@ CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y CONFIG_REISERFS_FS=m # CONFIG_REISERFS_CHECK is not set @@ -1281,22 +1407,22 @@ CONFIG_JFS_SECURITY=y # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set CONFIG_FS_POSIX_ACL=y +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=m CONFIG_XFS_QUOTA=y -CONFIG_XFS_SECURITY=y CONFIG_XFS_POSIX_ACL=y # CONFIG_XFS_RT is not set -# CONFIG_GFS2_FS is not set +# CONFIG_XFS_DEBUG is not set # CONFIG_OCFS2_FS is not set -CONFIG_MINIX_FS=m -CONFIG_ROMFS_FS=m +CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y CONFIG_QUOTA=y +# CONFIG_QUOTA_NETLINK_INTERFACE is not set +CONFIG_PRINT_QUOTA_WARNING=y # CONFIG_QFMT_V1 is not set CONFIG_QFMT_V2=y CONFIG_QUOTACTL=y -CONFIG_DNOTIFY=y CONFIG_AUTOFS_FS=y # CONFIG_AUTOFS4_FS is not set CONFIG_FUSE_FS=m @@ -1326,11 +1452,11 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1347,46 +1473,48 @@ CONFIG_EFS_FS=m CONFIG_JFFS2_FS=m CONFIG_JFFS2_FS_DEBUG=0 CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set # CONFIG_JFFS2_SUMMARY is not set CONFIG_JFFS2_FS_XATTR=y CONFIG_JFFS2_FS_POSIX_ACL=y CONFIG_JFFS2_FS_SECURITY=y CONFIG_JFFS2_COMPRESSION_OPTIONS=y CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set CONFIG_JFFS2_RTIME=y CONFIG_JFFS2_RUBIN=y # CONFIG_JFFS2_CMODE_NONE is not set CONFIG_JFFS2_CMODE_PRIORITY=y # CONFIG_JFFS2_CMODE_SIZE is not set +# CONFIG_JFFS2_CMODE_FAVOURLZO is not set +# CONFIG_UBIFS_FS is not set CONFIG_CRAMFS=m CONFIG_VXFS_FS=m +CONFIG_MINIX_FS=m +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set +CONFIG_ROMFS_FS=m CONFIG_SYSV_FS=m CONFIG_UFS_FS=m # CONFIG_UFS_FS_WRITE is not set # CONFIG_UFS_DEBUG is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set -# CONFIG_NFS_DIRECTIO is not set +CONFIG_ROOT_NFS=y CONFIG_NFSD=y CONFIG_NFSD_V3=y # CONFIG_NFSD_V3_ACL is not set # CONFIG_NFSD_V4 is not set -# CONFIG_NFSD_TCP is not set -CONFIG_ROOT_NFS=y CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_EXPORTFS=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y -# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_SUNRPC_REGISTER_V4 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -1400,10 +1528,6 @@ CONFIG_SUNRPC=y # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# CONFIG_NLS=m CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=m @@ -1444,29 +1568,30 @@ CONFIG_NLS_ISO8859_15=m CONFIG_NLS_KOI8_R=m CONFIG_NLS_KOI8_U=m CONFIG_NLS_UTF8=m - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # -# Profiling support -# -# CONFIG_PROFILING is not set - -# # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set -CONFIG_CROSSCOMPILE=y +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y CONFIG_CMDLINE="" # @@ -1474,51 +1599,103 @@ CONFIG_CMDLINE="" # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_XOR_BLOCKS=m CONFIG_ASYNC_CORE=m CONFIG_ASYNC_MEMCPY=m CONFIG_ASYNC_XOR=m CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_ABLKCIPHER=m -CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_AEAD=y +CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_GF128MUL=m +CONFIG_CRYPTO_NULL=m +CONFIG_CRYPTO_CRYPTD=m +CONFIG_CRYPTO_AUTHENC=m +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=m +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +CONFIG_CRYPTO_LRW=m +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# CONFIG_CRYPTO_HMAC=y CONFIG_CRYPTO_XCBC=m -CONFIG_CRYPTO_NULL=m + +# +# Digest +# +CONFIG_CRYPTO_CRC32C=m CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MD5=y +CONFIG_CRYPTO_MICHAEL_MIC=m +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=m CONFIG_CRYPTO_SHA256=m CONFIG_CRYPTO_SHA512=m -CONFIG_CRYPTO_WP512=m CONFIG_CRYPTO_TGR192=m -CONFIG_CRYPTO_GF128MUL=m -CONFIG_CRYPTO_ECB=m -CONFIG_CRYPTO_CBC=m -CONFIG_CRYPTO_PCBC=m -CONFIG_CRYPTO_LRW=m -CONFIG_CRYPTO_CRYPTD=m -CONFIG_CRYPTO_DES=m -CONFIG_CRYPTO_FCRYPT=m -CONFIG_CRYPTO_BLOWFISH=m -CONFIG_CRYPTO_TWOFISH=m -CONFIG_CRYPTO_TWOFISH_COMMON=m -CONFIG_CRYPTO_SERPENT=m +CONFIG_CRYPTO_WP512=m + +# +# Ciphers +# CONFIG_CRYPTO_AES=m +CONFIG_CRYPTO_ANUBIS=m +CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_BLOWFISH=m +CONFIG_CRYPTO_CAMELLIA=m CONFIG_CRYPTO_CAST5=m CONFIG_CRYPTO_CAST6=m -CONFIG_CRYPTO_TEA=m -CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_DES=m +CONFIG_CRYPTO_FCRYPT=m CONFIG_CRYPTO_KHAZAD=m -CONFIG_CRYPTO_ANUBIS=m +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +CONFIG_CRYPTO_SERPENT=m +CONFIG_CRYPTO_TEA=m +CONFIG_CRYPTO_TWOFISH=m +CONFIG_CRYPTO_TWOFISH_COMMON=m + +# +# Compression +# CONFIG_CRYPTO_DEFLATE=m -CONFIG_CRYPTO_MICHAEL_MIC=m -CONFIG_CRYPTO_CRC32C=m -CONFIG_CRYPTO_CAMELLIA=m -# CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y +# CONFIG_CRYPTO_DEV_HIFN_795X is not set # # Library routines @@ -1526,7 +1703,8 @@ CONFIG_CRYPTO_HW=y CONFIG_BITREVERSE=y # CONFIG_CRC_CCITT is not set CONFIG_CRC16=m -# CONFIG_CRC_ITU_T is not set +# CONFIG_CRC_T10DIF is not set +CONFIG_CRC_ITU_T=m CONFIG_CRC32=y # CONFIG_CRC7 is not set CONFIG_LIBCRC32C=m -- cgit v1.1 From 566a3b95579c123f7711e2f98d078f370746046b Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 1 Dec 2008 08:16:08 +0000 Subject: MIPS: Malta: Consolidate platform device code. After adding the RTC platform device to malta-platform.c malta-mtd.c should get unified with the rest of the platform device code. --- arch/mips/mti-malta/Makefile | 5 ++- arch/mips/mti-malta/malta-mtd.c | 63 ------------------------------------ arch/mips/mti-malta/malta-platform.c | 51 +++++++++++++++++++++++++++-- 3 files changed, 50 insertions(+), 69 deletions(-) delete mode 100644 arch/mips/mti-malta/malta-mtd.c (limited to 'arch') diff --git a/arch/mips/mti-malta/Makefile b/arch/mips/mti-malta/Makefile index cef2db8..32e8478 100644 --- a/arch/mips/mti-malta/Makefile +++ b/arch/mips/mti-malta/Makefile @@ -7,9 +7,8 @@ # obj-y := malta-amon.o malta-cmdline.o \ malta-display.o malta-init.o malta-int.o \ - malta-memory.o malta-mtd.o \ - malta-platform.o malta-reset.o \ - malta-setup.o malta-time.o + malta-memory.o malta-platform.o \ + malta-reset.o malta-setup.o malta-time.o obj-$(CONFIG_EARLY_PRINTK) += malta-console.o obj-$(CONFIG_PCI) += malta-pci.o diff --git a/arch/mips/mti-malta/malta-mtd.c b/arch/mips/mti-malta/malta-mtd.c deleted file mode 100644 index 8ad9bdf..0000000 --- a/arch/mips/mti-malta/malta-mtd.c +++ /dev/null @@ -1,63 +0,0 @@ -/* - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - * - * Copyright (C) 2006 MIPS Technologies, Inc. - * written by Ralf Baechle - */ - -#include -#include -#include -#include -#include - -static struct mtd_partition malta_mtd_partitions[] = { - { - .name = "YAMON", - .offset = 0x0, - .size = 0x100000, - .mask_flags = MTD_WRITEABLE - }, { - .name = "User FS", - .offset = 0x100000, - .size = 0x2e0000 - }, { - .name = "Board Config", - .offset = 0x3e0000, - .size = 0x020000, - .mask_flags = MTD_WRITEABLE - } -}; - -static struct physmap_flash_data malta_flash_data = { - .width = 4, - .nr_parts = ARRAY_SIZE(malta_mtd_partitions), - .parts = malta_mtd_partitions -}; - -static struct resource malta_flash_resource = { - .start = 0x1e000000, - .end = 0x1e3fffff, - .flags = IORESOURCE_MEM -}; - -static struct platform_device malta_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &malta_flash_data, - }, - .num_resources = 1, - .resource = &malta_flash_resource, -}; - -static int __init malta_mtd_init(void) -{ - platform_device_register(&malta_flash); - - return 0; -} - -module_init(malta_mtd_init) diff --git a/arch/mips/mti-malta/malta-platform.c b/arch/mips/mti-malta/malta-platform.c index 6a476f7..72e32a7 100644 --- a/arch/mips/mti-malta/malta-platform.c +++ b/arch/mips/mti-malta/malta-platform.c @@ -3,8 +3,9 @@ * License. See the file "COPYING" in the main directory of this archive * for more details. * - * Copyright (C) 2007 MIPS Technologies, Inc. + * Copyright (C) 2006, 07 MIPS Technologies, Inc. * written by Ralf Baechle (ralf@linux-mips.org) + * written by Ralf Baechle * * Copyright (C) 2008 Wind River Systems, Inc. * updated by Tiejun Chen @@ -20,11 +21,14 @@ * * 2. Register RTC-CMOS platform device on Malta. */ -#include #include #include #include +#include +#include +#include #include +#include #define SMC_PORT(base, int) \ { \ @@ -54,7 +58,7 @@ static struct plat_serial8250_port uart8250_data[] = { static struct platform_device malta_uart8250_device = { .name = "serial8250", - .id = PLAT8250_DEV_PLATFORM2, + .id = PLAT8250_DEV_PLATFORM, .dev = { .platform_data = uart8250_data, }, @@ -79,9 +83,50 @@ static struct platform_device malta_rtc_device = { .num_resources = ARRAY_SIZE(malta_rtc_resources), }; +static struct mtd_partition malta_mtd_partitions[] = { + { + .name = "YAMON", + .offset = 0x0, + .size = 0x100000, + .mask_flags = MTD_WRITEABLE + }, { + .name = "User FS", + .offset = 0x100000, + .size = 0x2e0000 + }, { + .name = "Board Config", + .offset = 0x3e0000, + .size = 0x020000, + .mask_flags = MTD_WRITEABLE + } +}; + +static struct physmap_flash_data malta_flash_data = { + .width = 4, + .nr_parts = ARRAY_SIZE(malta_mtd_partitions), + .parts = malta_mtd_partitions +}; + +static struct resource malta_flash_resource = { + .start = 0x1e000000, + .end = 0x1e3fffff, + .flags = IORESOURCE_MEM +}; + +static struct platform_device malta_flash_device = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &malta_flash_data, + }, + .num_resources = 1, + .resource = &malta_flash_resource, +}; + static struct platform_device *malta_devices[] __initdata = { &malta_uart8250_device, &malta_rtc_device, + &malta_flash_device, }; static int __init malta_add_devices(void) -- cgit v1.1 From 08d30879a6d3ce399f48def7c494853b5b5f2062 Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Wed, 3 Dec 2008 16:33:17 +0000 Subject: MIPS: o32: Fix number of arguments to splice(2). The syscall code was assuming splice only takes 4 arguments so no stack arguments were being copied from the userspace stack to the kernel stack. As the result splice was likely to fail with EINVAL. Signed-off-by: Ralf Baechle --- arch/mips/kernel/scall32-o32.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/kernel/scall32-o32.S b/arch/mips/kernel/scall32-o32.S index 34a4dbd..d0916a5 100644 --- a/arch/mips/kernel/scall32-o32.S +++ b/arch/mips/kernel/scall32-o32.S @@ -624,7 +624,7 @@ einval: li v0, -ENOSYS sys sys_pselect6 6 sys sys_ppoll 5 sys sys_unshare 1 - sys sys_splice 4 + sys sys_splice 6 sys sys_sync_file_range 7 /* 4305 */ sys sys_tee 4 sys sys_vmsplice 4 -- cgit v1.1 From 8d13cb26cd3bf23946743a5b4af2fecd88fc4974 Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Wed, 3 Dec 2008 17:03:27 +0000 Subject: MIPS: 64-bit: vmsplice needs to use the compat wrapper for o32 and N32. Signed-off-by: Ralf Baechle --- arch/mips/kernel/scall64-n32.S | 2 +- arch/mips/kernel/scall64-o32.S | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/mips/kernel/scall64-n32.S b/arch/mips/kernel/scall64-n32.S index e266b3a..30f3b63 100644 --- a/arch/mips/kernel/scall64-n32.S +++ b/arch/mips/kernel/scall64-n32.S @@ -390,7 +390,7 @@ EXPORT(sysn32_call_table) PTR sys_splice PTR sys_sync_file_range PTR sys_tee - PTR sys_vmsplice /* 6270 */ + PTR compat_sys_vmsplice /* 6270 */ PTR sys_move_pages PTR compat_sys_set_robust_list PTR compat_sys_get_robust_list diff --git a/arch/mips/kernel/scall64-o32.S b/arch/mips/kernel/scall64-o32.S index facb41a..3d55e3b 100644 --- a/arch/mips/kernel/scall64-o32.S +++ b/arch/mips/kernel/scall64-o32.S @@ -510,7 +510,7 @@ sys_call_table: PTR sys_splice PTR sys32_sync_file_range /* 4305 */ PTR sys_tee - PTR sys_vmsplice + PTR compat_sys_vmsplice PTR compat_sys_move_pages PTR compat_sys_set_robust_list PTR compat_sys_get_robust_list /* 4310 */ -- cgit v1.1 From c6cb4df96fa22d1174d6fb6dfc2c7501d7afaeea Mon Sep 17 00:00:00 2001 From: David Daney Date: Fri, 31 Oct 2008 11:23:09 -0700 Subject: MIPS: Return ENOSYS from sys32_syscall on 64bit kernels like elsewhere. When the o32 errno was changed to ENOSYS, we forgot to update the code for 64bit kernels. Signed-off-by: David Daney Acked-by: Atsushi Nemoto Signed-off-by: Ralf Baechle --- arch/mips/kernel/scall64-o32.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/kernel/scall64-o32.S b/arch/mips/kernel/scall64-o32.S index 3d55e3b..fefef4a 100644 --- a/arch/mips/kernel/scall64-o32.S +++ b/arch/mips/kernel/scall64-o32.S @@ -196,7 +196,7 @@ LEAF(sys32_syscall) jr t2 /* Unreached */ -einval: li v0, -EINVAL +einval: li v0, -ENOSYS jr ra END(sys32_syscall) -- cgit v1.1 From b2c2717bae3ad62f18a51ea10188176134bac79c Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 4 Dec 2008 20:52:31 +0300 Subject: powerpc/83xx: Enable FIXED_PHY in mpc834x_itx and mpc83xx defconfigs This is needed so that Vitesse 7385 5-port switch could work on MPC8349E-mITX boards. Signed-off-by: Anton Vorontsov Acked-by: Timur Tabi Signed-off-by: Kumar Gala --- arch/powerpc/configs/83xx/mpc834x_itx_defconfig | 2 +- arch/powerpc/configs/mpc83xx_defconfig | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/configs/83xx/mpc834x_itx_defconfig b/arch/powerpc/configs/83xx/mpc834x_itx_defconfig index e55ff7c..07a674f 100644 --- a/arch/powerpc/configs/83xx/mpc834x_itx_defconfig +++ b/arch/powerpc/configs/83xx/mpc834x_itx_defconfig @@ -723,7 +723,7 @@ CONFIG_CICADA_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_REALTEK_PHY is not set -# CONFIG_FIXED_PHY is not set +CONFIG_FIXED_PHY=y # CONFIG_MDIO_BITBANG is not set # CONFIG_NET_ETHERNET is not set CONFIG_NETDEV_1000=y diff --git a/arch/powerpc/configs/mpc83xx_defconfig b/arch/powerpc/configs/mpc83xx_defconfig index 15eb30c..d582014 100644 --- a/arch/powerpc/configs/mpc83xx_defconfig +++ b/arch/powerpc/configs/mpc83xx_defconfig @@ -682,7 +682,7 @@ CONFIG_VITESSE_PHY=y # CONFIG_BROADCOM_PHY is not set CONFIG_ICPLUS_PHY=y # CONFIG_REALTEK_PHY is not set -# CONFIG_FIXED_PHY is not set +CONFIG_FIXED_PHY=y # CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y -- cgit v1.1 From 8ebcfc8bcb55261cf01fc302d707fbba46242bf1 Mon Sep 17 00:00:00 2001 From: Nick Andrew Date: Fri, 5 Dec 2008 11:36:54 +1100 Subject: MIPS: Fix incorrect use of loose in vpe.c It should be 'lose', not 'loose'. Signed-off-by: Nick Andrew Signed-off-by: Ralf Baechle --- arch/mips/kernel/vpe.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c index 972b2d2..a1b3da6 100644 --- a/arch/mips/kernel/vpe.c +++ b/arch/mips/kernel/vpe.c @@ -1134,7 +1134,7 @@ static int vpe_release(struct inode *inode, struct file *filp) /* It's good to be able to run the SP and if it chokes have a look at the /dev/rt?. But if we reset the pointer to the shared struct we - loose what has happened. So perhaps if garbage is sent to the vpe + lose what has happened. So perhaps if garbage is sent to the vpe device, use it as a trigger for the reset. Hopefully a nice executable will be along shortly. */ if (ret < 0) -- cgit v1.1 From 640d17d60e83401e10e66a0ab6e9e2d6350df656 Mon Sep 17 00:00:00 2001 From: Grant Likely Date: Thu, 4 Dec 2008 05:39:55 +0000 Subject: powerpc/virtex5: Fix Virtex5 machine check handling The 440x5 core in the Virtex5 uses the 440A type machine check (ie, they have MCSRR0/MCSRR1). They thus need to call the appropriate fixup function to hook the right variant of the exception. Without this, all machine checks become fatal due to loss of context when entering the exception handler. Signed-off-by: Grant Likely Signed-off-by: Josh Boyer --- arch/powerpc/kernel/cpu_setup_44x.S | 1 + arch/powerpc/kernel/cputable.c | 3 +++ 2 files changed, 4 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/kernel/cpu_setup_44x.S b/arch/powerpc/kernel/cpu_setup_44x.S index 31c18b5..10b4ab1 100644 --- a/arch/powerpc/kernel/cpu_setup_44x.S +++ b/arch/powerpc/kernel/cpu_setup_44x.S @@ -40,6 +40,7 @@ _GLOBAL(__setup_cpu_460gt) mtlr r4 blr +_GLOBAL(__setup_cpu_440x5) _GLOBAL(__setup_cpu_440gx) _GLOBAL(__setup_cpu_440spe) b __fixup_440A_mcheck diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c index b1eb834..7e87195 100644 --- a/arch/powerpc/kernel/cputable.c +++ b/arch/powerpc/kernel/cputable.c @@ -39,6 +39,7 @@ extern void __setup_cpu_440epx(unsigned long offset, struct cpu_spec* spec); extern void __setup_cpu_440gx(unsigned long offset, struct cpu_spec* spec); extern void __setup_cpu_440grx(unsigned long offset, struct cpu_spec* spec); extern void __setup_cpu_440spe(unsigned long offset, struct cpu_spec* spec); +extern void __setup_cpu_440x5(unsigned long offset, struct cpu_spec* spec); extern void __setup_cpu_460ex(unsigned long offset, struct cpu_spec* spec); extern void __setup_cpu_460gt(unsigned long offset, struct cpu_spec* spec); extern void __setup_cpu_603(unsigned long offset, struct cpu_spec* spec); @@ -1500,6 +1501,8 @@ static struct cpu_spec __initdata cpu_specs[] = { .cpu_user_features = COMMON_USER_BOOKE, .icache_bsize = 32, .dcache_bsize = 32, + .cpu_setup = __setup_cpu_440x5, + .machine_check = machine_check_440A, .platform = "ppc440", }, { /* 460EX */ -- cgit v1.1 From 794baba637999b81aa40e60fae1fa91978e08808 Mon Sep 17 00:00:00 2001 From: Lennert Buytenhek Date: Fri, 5 Dec 2008 03:25:47 +0100 Subject: [ARM] 5340/1: fix stack placement after noexecstack changes Commit 8ec53663d2698076468b3e1edc4e1b418bd54de3 ("[ARM] Improve non-executable support") added support for detecting non-executable stack binaries. One of the things it does is to make READ_IMPLIES_EXEC be set in ->personality if we are running on a CPU that doesn't support the XN ("Execute Never") page table bit or if we are running a binary that needs an executable stack. This exposed a latent bug in ARM's asm/processor.h due to which we'll end up placing the stack at a very low address, where it will bump into the heap on any application that uses significant amount of stack or heap or both, causing many interesting crashes. Fix this by testing the ADDR_LIMIT_32BIT bit in ->personality instead of testing for equality against PER_LINUX_32BIT. Reviewed-by: Nicolas Pitre Signed-off-by: Lennert Buytenhek Signed-off-by: Russell King --- arch/arm/include/asm/processor.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/include/asm/processor.h b/arch/arm/include/asm/processor.h index 517a4d6..6ff3379 100644 --- a/arch/arm/include/asm/processor.h +++ b/arch/arm/include/asm/processor.h @@ -23,7 +23,7 @@ #include #ifdef __KERNEL__ -#define STACK_TOP ((current->personality == PER_LINUX_32BIT) ? \ +#define STACK_TOP ((current->personality & ADDR_LIMIT_32BIT) ? \ TASK_SIZE : TASK_SIZE_26) #define STACK_TOP_MAX TASK_SIZE #endif -- cgit v1.1 From baa745a3378046ca1c5477495df6ccbec7690428 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 7 Dec 2008 09:44:55 +0000 Subject: [ARM] Fix alignment fault handling for ARMv6 and later CPUs On ARMv6 and later CPUs, it is possible for userspace processes to get stuck on a misaligned load or store due to the "ignore fault" setting; unlike previous CPUs, retrying the instruction without the 'A' bit set does not always cause the load to succeed. We have no real option but to default to fixing up alignment faults on these CPUs, and having the CPU fix up those misaligned accesses which it can. Reported-by: Wolfgang Grandegger Signed-off-by: Russell King --- arch/arm/mm/alignment.c | 26 +++++++++++++++++++++++--- 1 file changed, 23 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/mm/alignment.c b/arch/arm/mm/alignment.c index 133e65d..2d5884c 100644 --- a/arch/arm/mm/alignment.c +++ b/arch/arm/mm/alignment.c @@ -70,6 +70,10 @@ static unsigned long ai_dword; static unsigned long ai_multi; static int ai_usermode; +#define UM_WARN (1 << 0) +#define UM_FIXUP (1 << 1) +#define UM_SIGNAL (1 << 2) + #ifdef CONFIG_PROC_FS static const char *usermode_action[] = { "ignored", @@ -754,7 +758,7 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) user: ai_user += 1; - if (ai_usermode & 1) + if (ai_usermode & UM_WARN) printk("Alignment trap: %s (%d) PC=0x%08lx Instr=0x%0*lx " "Address=0x%08lx FSR 0x%03x\n", current->comm, task_pid_nr(current), instrptr, @@ -762,10 +766,10 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) thumb_mode(regs) ? tinstr : instr, addr, fsr); - if (ai_usermode & 2) + if (ai_usermode & UM_FIXUP) goto fixup; - if (ai_usermode & 4) + if (ai_usermode & UM_SIGNAL) force_sig(SIGBUS, current); else set_cr(cr_no_alignment); @@ -796,6 +800,22 @@ static int __init alignment_init(void) res->write_proc = proc_alignment_write; #endif + /* + * ARMv6 and later CPUs can perform unaligned accesses for + * most single load and store instructions up to word size. + * LDM, STM, LDRD and STRD still need to be handled. + * + * Ignoring the alignment fault is not an option on these + * CPUs since we spin re-faulting the instruction without + * making any progress. + */ + if (cpu_architecture() >= CPU_ARCH_ARMv6 && (cr_alignment & CR_U)) { + cr_alignment &= ~CR_A; + cr_no_alignment &= ~CR_A; + set_cr(cr_alignment); + ai_usermode = UM_FIXUP; + } + hook_fault_code(1, do_alignment, SIGILL, "alignment exception"); hook_fault_code(3, do_alignment, SIGILL, "alignment exception"); -- cgit v1.1 From 0b8f1efad30bd58f89961b82dfe68b9edf8fd2ac Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Fri, 5 Dec 2008 18:58:31 -0800 Subject: sparse irq_desc[] array: core kernel and x86 changes Impact: new feature Problem on distro kernels: irq_desc[NR_IRQS] takes megabytes of RAM with NR_CPUS set to large values. The goal is to be able to scale up to much larger NR_IRQS value without impacting the (important) common case. To solve this, we generalize irq_desc[NR_IRQS] to an (optional) array of irq_desc pointers. When CONFIG_SPARSE_IRQ=y is used, we use kzalloc_node to get irq_desc, this also makes the IRQ descriptors NUMA-local (to the site that calls request_irq()). This gets rid of the irq_cfg[] static array on x86 as well: irq_cfg now uses desc->chip_data for x86 to store irq_cfg. Signed-off-by: Yinghai Lu Signed-off-by: Ingo Molnar --- arch/x86/Kconfig | 10 ++ arch/x86/include/asm/irq_vectors.h | 9 ++ arch/x86/kernel/io_apic.c | 301 +++++++++++++++++++++++-------------- arch/x86/kernel/irq.c | 3 + arch/x86/kernel/irq_32.c | 2 + arch/x86/kernel/irq_64.c | 2 + arch/x86/kernel/irqinit_32.c | 1 - arch/x86/kernel/irqinit_64.c | 1 - 8 files changed, 216 insertions(+), 113 deletions(-) (limited to 'arch') diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index ac22bb7..48ac688 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -238,6 +238,16 @@ config X86_HAS_BOOT_CPU_ID def_bool y depends on X86_VOYAGER +config SPARSE_IRQ + bool "Support sparse irq numbering" + depends on PCI_MSI || HT_IRQ + default y + help + This enables support for sparse irq, esp for msi/msi-x. You may need + if you have lots of cards supports msi-x installed. + + If you don't know what to do here, say Y. + config X86_FIND_SMP_CONFIG def_bool y depends on X86_MPPARSE || X86_VOYAGER diff --git a/arch/x86/include/asm/irq_vectors.h b/arch/x86/include/asm/irq_vectors.h index 0005adb..bb6b69a 100644 --- a/arch/x86/include/asm/irq_vectors.h +++ b/arch/x86/include/asm/irq_vectors.h @@ -102,11 +102,20 @@ #define invalid_vm86_irq(irq) ((irq) < 3 || (irq) > 15) #if defined(CONFIG_X86_IO_APIC) && !defined(CONFIG_X86_VOYAGER) + +#ifndef CONFIG_SPARSE_IRQ # if NR_CPUS < MAX_IO_APICS # define NR_IRQS (NR_VECTORS + (32 * NR_CPUS)) # else # define NR_IRQS (NR_VECTORS + (32 * MAX_IO_APICS)) # endif +#else +# if (8 * NR_CPUS) > (32 * MAX_IO_APICS) +# define NR_IRQS (NR_VECTORS + (8 * NR_CPUS)) +# else +# define NR_IRQS (NR_VECTORS + (32 * MAX_IO_APICS)) +# endif +#endif #elif defined(CONFIG_X86_VOYAGER) diff --git a/arch/x86/kernel/io_apic.c b/arch/x86/kernel/io_apic.c index 9043251..9de17f5 100644 --- a/arch/x86/kernel/io_apic.c +++ b/arch/x86/kernel/io_apic.c @@ -108,8 +108,33 @@ static int __init parse_noapic(char *str) early_param("noapic", parse_noapic); struct irq_pin_list; + +/* + * This is performance-critical, we want to do it O(1) + * + * the indexing order of this array favors 1:1 mappings + * between pins and IRQs. + */ + +struct irq_pin_list { + int apic, pin; + struct irq_pin_list *next; +}; + +static struct irq_pin_list *get_one_free_irq_2_pin(int cpu) +{ + struct irq_pin_list *pin; + int node; + + node = cpu_to_node(cpu); + + pin = kzalloc_node(sizeof(*pin), GFP_ATOMIC, node); + printk(KERN_DEBUG " alloc irq_2_pin on cpu %d node %d\n", cpu, node); + + return pin; +} + struct irq_cfg { - unsigned int irq; struct irq_pin_list *irq_2_pin; cpumask_t domain; cpumask_t old_domain; @@ -119,83 +144,93 @@ struct irq_cfg { }; /* irq_cfg is indexed by the sum of all RTEs in all I/O APICs. */ +#ifdef CONFIG_SPARSE_IRQ +static struct irq_cfg irq_cfgx[] = { +#else static struct irq_cfg irq_cfgx[NR_IRQS] = { - [0] = { .irq = 0, .domain = CPU_MASK_ALL, .vector = IRQ0_VECTOR, }, - [1] = { .irq = 1, .domain = CPU_MASK_ALL, .vector = IRQ1_VECTOR, }, - [2] = { .irq = 2, .domain = CPU_MASK_ALL, .vector = IRQ2_VECTOR, }, - [3] = { .irq = 3, .domain = CPU_MASK_ALL, .vector = IRQ3_VECTOR, }, - [4] = { .irq = 4, .domain = CPU_MASK_ALL, .vector = IRQ4_VECTOR, }, - [5] = { .irq = 5, .domain = CPU_MASK_ALL, .vector = IRQ5_VECTOR, }, - [6] = { .irq = 6, .domain = CPU_MASK_ALL, .vector = IRQ6_VECTOR, }, - [7] = { .irq = 7, .domain = CPU_MASK_ALL, .vector = IRQ7_VECTOR, }, - [8] = { .irq = 8, .domain = CPU_MASK_ALL, .vector = IRQ8_VECTOR, }, - [9] = { .irq = 9, .domain = CPU_MASK_ALL, .vector = IRQ9_VECTOR, }, - [10] = { .irq = 10, .domain = CPU_MASK_ALL, .vector = IRQ10_VECTOR, }, - [11] = { .irq = 11, .domain = CPU_MASK_ALL, .vector = IRQ11_VECTOR, }, - [12] = { .irq = 12, .domain = CPU_MASK_ALL, .vector = IRQ12_VECTOR, }, - [13] = { .irq = 13, .domain = CPU_MASK_ALL, .vector = IRQ13_VECTOR, }, - [14] = { .irq = 14, .domain = CPU_MASK_ALL, .vector = IRQ14_VECTOR, }, - [15] = { .irq = 15, .domain = CPU_MASK_ALL, .vector = IRQ15_VECTOR, }, +#endif + [0] = { .domain = CPU_MASK_ALL, .vector = IRQ0_VECTOR, }, + [1] = { .domain = CPU_MASK_ALL, .vector = IRQ1_VECTOR, }, + [2] = { .domain = CPU_MASK_ALL, .vector = IRQ2_VECTOR, }, + [3] = { .domain = CPU_MASK_ALL, .vector = IRQ3_VECTOR, }, + [4] = { .domain = CPU_MASK_ALL, .vector = IRQ4_VECTOR, }, + [5] = { .domain = CPU_MASK_ALL, .vector = IRQ5_VECTOR, }, + [6] = { .domain = CPU_MASK_ALL, .vector = IRQ6_VECTOR, }, + [7] = { .domain = CPU_MASK_ALL, .vector = IRQ7_VECTOR, }, + [8] = { .domain = CPU_MASK_ALL, .vector = IRQ8_VECTOR, }, + [9] = { .domain = CPU_MASK_ALL, .vector = IRQ9_VECTOR, }, + [10] = { .domain = CPU_MASK_ALL, .vector = IRQ10_VECTOR, }, + [11] = { .domain = CPU_MASK_ALL, .vector = IRQ11_VECTOR, }, + [12] = { .domain = CPU_MASK_ALL, .vector = IRQ12_VECTOR, }, + [13] = { .domain = CPU_MASK_ALL, .vector = IRQ13_VECTOR, }, + [14] = { .domain = CPU_MASK_ALL, .vector = IRQ14_VECTOR, }, + [15] = { .domain = CPU_MASK_ALL, .vector = IRQ15_VECTOR, }, }; -#define for_each_irq_cfg(irq, cfg) \ - for (irq = 0, cfg = irq_cfgx; irq < nr_irqs; irq++, cfg++) - -static struct irq_cfg *irq_cfg(unsigned int irq) +void __init arch_early_irq_init(void) { - return irq < nr_irqs ? irq_cfgx + irq : NULL; -} + struct irq_cfg *cfg; + struct irq_desc *desc; + int count; + int i; -static struct irq_cfg *irq_cfg_alloc(unsigned int irq) -{ - return irq_cfg(irq); -} + cfg = irq_cfgx; + count = ARRAY_SIZE(irq_cfgx); -/* - * Rough estimation of how many shared IRQs there are, can be changed - * anytime. - */ -#define MAX_PLUS_SHARED_IRQS NR_IRQS -#define PIN_MAP_SIZE (MAX_PLUS_SHARED_IRQS + NR_IRQS) + for (i = 0; i < count; i++) { + desc = irq_to_desc(i); + desc->chip_data = &cfg[i]; + } +} -/* - * This is performance-critical, we want to do it O(1) - * - * the indexing order of this array favors 1:1 mappings - * between pins and IRQs. - */ +#ifdef CONFIG_SPARSE_IRQ +static struct irq_cfg *irq_cfg(unsigned int irq) +{ + struct irq_cfg *cfg = NULL; + struct irq_desc *desc; -struct irq_pin_list { - int apic, pin; - struct irq_pin_list *next; -}; + desc = irq_to_desc(irq); + if (desc) + cfg = desc->chip_data; -static struct irq_pin_list irq_2_pin_head[PIN_MAP_SIZE]; -static struct irq_pin_list *irq_2_pin_ptr; + return cfg; +} -static void __init irq_2_pin_init(void) +static struct irq_cfg *get_one_free_irq_cfg(int cpu) { - struct irq_pin_list *pin = irq_2_pin_head; - int i; + struct irq_cfg *cfg; + int node; + + node = cpu_to_node(cpu); - for (i = 1; i < PIN_MAP_SIZE; i++) - pin[i-1].next = &pin[i]; + cfg = kzalloc_node(sizeof(*cfg), GFP_ATOMIC, node); + printk(KERN_DEBUG " alloc irq_cfg on cpu %d node %d\n", cpu, node); - irq_2_pin_ptr = &pin[0]; + return cfg; } -static struct irq_pin_list *get_one_free_irq_2_pin(void) +void arch_init_chip_data(struct irq_desc *desc, int cpu) { - struct irq_pin_list *pin = irq_2_pin_ptr; + struct irq_cfg *cfg; - if (!pin) - panic("can not get more irq_2_pin\n"); + cfg = desc->chip_data; + if (!cfg) { + desc->chip_data = get_one_free_irq_cfg(cpu); + if (!desc->chip_data) { + printk(KERN_ERR "can not alloc irq_cfg\n"); + BUG_ON(1); + } + } +} - irq_2_pin_ptr = pin->next; - pin->next = NULL; - return pin; +#else +static struct irq_cfg *irq_cfg(unsigned int irq) +{ + return irq < nr_irqs ? irq_cfgx + irq : NULL; } +#endif + struct io_apic { unsigned int index; unsigned int unused[3]; @@ -397,16 +432,19 @@ static void set_ioapic_affinity_irq(unsigned int irq, cpumask_t mask) * shared ISA-space IRQs, so we have to support them. We are super * fast in the common case, and fast for shared ISA-space IRQs. */ -static void add_pin_to_irq(unsigned int irq, int apic, int pin) +static void add_pin_to_irq_cpu(unsigned int irq, int cpu, int apic, int pin) { - struct irq_cfg *cfg; struct irq_pin_list *entry; + struct irq_cfg *cfg = irq_cfg(irq); - /* first time to refer irq_cfg, so with new */ - cfg = irq_cfg_alloc(irq); entry = cfg->irq_2_pin; if (!entry) { - entry = get_one_free_irq_2_pin(); + entry = get_one_free_irq_2_pin(cpu); + if (!entry) { + printk(KERN_ERR "can not alloc irq_2_pin to add %d - %d\n", + apic, pin); + return; + } cfg->irq_2_pin = entry; entry->apic = apic; entry->pin = pin; @@ -421,7 +459,7 @@ static void add_pin_to_irq(unsigned int irq, int apic, int pin) entry = entry->next; } - entry->next = get_one_free_irq_2_pin(); + entry->next = get_one_free_irq_2_pin(cpu); entry = entry->next; entry->apic = apic; entry->pin = pin; @@ -430,7 +468,7 @@ static void add_pin_to_irq(unsigned int irq, int apic, int pin) /* * Reroute an IRQ to a different pin. */ -static void __init replace_pin_at_irq(unsigned int irq, +static void __init replace_pin_at_irq(unsigned int irq, int cpu, int oldapic, int oldpin, int newapic, int newpin) { @@ -451,7 +489,7 @@ static void __init replace_pin_at_irq(unsigned int irq, /* why? call replace before add? */ if (!replaced) - add_pin_to_irq(irq, newapic, newpin); + add_pin_to_irq_cpu(irq, cpu, newapic, newpin); } static inline void io_apic_modify_irq(unsigned int irq, @@ -1162,9 +1200,13 @@ void __setup_vector_irq(int cpu) /* This function must be called with vector_lock held */ int irq, vector; struct irq_cfg *cfg; + struct irq_desc *desc; /* Mark the inuse vectors */ - for_each_irq_cfg(irq, cfg) { + for_each_irq_desc(irq, desc) { + if (!desc) + continue; + cfg = desc->chip_data; if (!cpu_isset(cpu, cfg->domain)) continue; vector = cfg->vector; @@ -1356,6 +1398,8 @@ static void __init setup_IO_APIC_irqs(void) { int apic, pin, idx, irq; int notcon = 0; + struct irq_desc *desc; + int cpu = boot_cpu_id; apic_printk(APIC_VERBOSE, KERN_DEBUG "init IO_APIC IRQs\n"); @@ -1387,7 +1431,12 @@ static void __init setup_IO_APIC_irqs(void) if (multi_timer_check(apic, irq)) continue; #endif - add_pin_to_irq(irq, apic, pin); + desc = irq_to_desc_alloc_cpu(irq, cpu); + if (!desc) { + printk(KERN_INFO "can not get irq_desc for %d\n", irq); + continue; + } + add_pin_to_irq_cpu(irq, cpu, apic, pin); setup_IO_APIC_irq(apic, pin, irq, irq_trigger(idx), irq_polarity(idx)); @@ -1448,6 +1497,7 @@ __apicdebuginit(void) print_IO_APIC(void) union IO_APIC_reg_03 reg_03; unsigned long flags; struct irq_cfg *cfg; + struct irq_desc *desc; unsigned int irq; if (apic_verbosity == APIC_QUIET) @@ -1537,8 +1587,13 @@ __apicdebuginit(void) print_IO_APIC(void) } } printk(KERN_DEBUG "IRQ to pin mappings:\n"); - for_each_irq_cfg(irq, cfg) { - struct irq_pin_list *entry = cfg->irq_2_pin; + for_each_irq_desc(irq, desc) { + struct irq_pin_list *entry; + + if (!desc) + continue; + cfg = desc->chip_data; + entry = cfg->irq_2_pin; if (!entry) continue; printk(KERN_DEBUG "IRQ%d ", irq); @@ -2022,6 +2077,7 @@ static unsigned int startup_ioapic_irq(unsigned int irq) { int was_pending = 0; unsigned long flags; + struct irq_cfg *cfg; spin_lock_irqsave(&ioapic_lock, flags); if (irq < 16) { @@ -2029,6 +2085,7 @@ static unsigned int startup_ioapic_irq(unsigned int irq) if (i8259A_irq_pending(irq)) was_pending = 1; } + cfg = irq_cfg(irq); __unmask_IO_APIC_irq(irq); spin_unlock_irqrestore(&ioapic_lock, flags); @@ -2178,6 +2235,9 @@ static void ir_irq_migration(struct work_struct *work) struct irq_desc *desc; for_each_irq_desc(irq, desc) { + if (!desc) + continue; + if (desc->status & IRQ_MOVE_PENDING) { unsigned long flags; @@ -2229,6 +2289,9 @@ asmlinkage void smp_irq_move_cleanup_interrupt(void) struct irq_cfg *cfg; irq = __get_cpu_var(vector_irq)[vector]; + if (irq == -1) + continue; + desc = irq_to_desc(irq); if (!desc) continue; @@ -2430,8 +2493,12 @@ static inline void init_IO_APIC_traps(void) * Also, we've got to be careful not to trash gate * 0x80, because int 0x80 is hm, kind of importantish. ;) */ - for_each_irq_cfg(irq, cfg) { - if (IO_APIC_IRQ(irq) && !cfg->vector) { + for_each_irq_desc(irq, desc) { + if (!desc) + continue; + + cfg = desc->chip_data; + if (IO_APIC_IRQ(irq) && cfg && !cfg->vector) { /* * Hmm.. We don't have an entry for this, * so default to an old-fashioned 8259 @@ -2439,11 +2506,9 @@ static inline void init_IO_APIC_traps(void) */ if (irq < 16) make_8259A_irq(irq); - else { - desc = irq_to_desc(irq); + else /* Strange. Oh, well.. */ desc->chip = &no_irq_chip; - } } } } @@ -2654,7 +2719,7 @@ static inline void __init check_timer(void) * Ok, does IRQ0 through the IOAPIC work? */ if (no_pin1) { - add_pin_to_irq(0, apic1, pin1); + add_pin_to_irq_cpu(0, boot_cpu_id, apic1, pin1); setup_timer_IRQ0_pin(apic1, pin1, cfg->vector); } unmask_IO_APIC_irq(0); @@ -2683,7 +2748,7 @@ static inline void __init check_timer(void) /* * legacy devices should be connected to IO APIC #0 */ - replace_pin_at_irq(0, apic1, pin1, apic2, pin2); + replace_pin_at_irq(0, boot_cpu_id, apic1, pin1, apic2, pin2); setup_timer_IRQ0_pin(apic2, pin2, cfg->vector); unmask_IO_APIC_irq(0); enable_8259A_irq(0); @@ -2902,21 +2967,25 @@ unsigned int create_irq_nr(unsigned int irq_want) unsigned int irq; unsigned int new; unsigned long flags; - struct irq_cfg *cfg_new; - - irq_want = nr_irqs - 1; + struct irq_cfg *cfg_new = NULL; + int cpu = boot_cpu_id; + struct irq_desc *desc_new = NULL; irq = 0; spin_lock_irqsave(&vector_lock, flags); for (new = irq_want; new > 0; new--) { if (platform_legacy_irq(new)) continue; - cfg_new = irq_cfg(new); - if (cfg_new && cfg_new->vector != 0) + + desc_new = irq_to_desc_alloc_cpu(new, cpu); + if (!desc_new) { + printk(KERN_INFO "can not get irq_desc for %d\n", new); + continue; + } + cfg_new = desc_new->chip_data; + + if (cfg_new->vector != 0) continue; - /* check if need to create one */ - if (!cfg_new) - cfg_new = irq_cfg_alloc(new); if (__assign_irq_vector(new, TARGET_CPUS) == 0) irq = new; break; @@ -2925,6 +2994,9 @@ unsigned int create_irq_nr(unsigned int irq_want) if (irq > 0) { dynamic_irq_init(irq); + /* restore it, in case dynamic_irq_init clear it */ + if (desc_new) + desc_new->chip_data = cfg_new; } return irq; } @@ -2944,8 +3016,16 @@ int create_irq(void) void destroy_irq(unsigned int irq) { unsigned long flags; + struct irq_cfg *cfg; + struct irq_desc *desc; + /* store it, in case dynamic_irq_cleanup clear it */ + desc = irq_to_desc(irq); + cfg = desc->chip_data; dynamic_irq_cleanup(irq); + /* connect back irq_cfg */ + if (desc) + desc->chip_data = cfg; #ifdef CONFIG_INTR_REMAP free_irte(irq); @@ -3195,26 +3275,13 @@ static int setup_msi_irq(struct pci_dev *dev, struct msi_desc *desc, int irq) return 0; } -static unsigned int build_irq_for_pci_dev(struct pci_dev *dev) -{ - unsigned int irq; - - irq = dev->bus->number; - irq <<= 8; - irq |= dev->devfn; - irq <<= 12; - - return irq; -} - -int arch_setup_msi_irq(struct pci_dev *dev, struct msi_desc *desc) +int arch_setup_msi_irq(struct pci_dev *dev, struct msi_desc *msidesc) { unsigned int irq; int ret; unsigned int irq_want; - irq_want = build_irq_for_pci_dev(dev) + 0x100; - + irq_want = nr_irqs - 1; irq = create_irq_nr(irq_want); if (irq == 0) return -1; @@ -3228,7 +3295,7 @@ int arch_setup_msi_irq(struct pci_dev *dev, struct msi_desc *desc) goto error; no_ir: #endif - ret = setup_msi_irq(dev, desc, irq); + ret = setup_msi_irq(dev, msidesc, irq); if (ret < 0) { destroy_irq(irq); return ret; @@ -3246,7 +3313,7 @@ int arch_setup_msi_irqs(struct pci_dev *dev, int nvec, int type) { unsigned int irq; int ret, sub_handle; - struct msi_desc *desc; + struct msi_desc *msidesc; unsigned int irq_want; #ifdef CONFIG_INTR_REMAP @@ -3254,10 +3321,11 @@ int arch_setup_msi_irqs(struct pci_dev *dev, int nvec, int type) int index = 0; #endif - irq_want = build_irq_for_pci_dev(dev) + 0x100; + irq_want = nr_irqs - 1; sub_handle = 0; - list_for_each_entry(desc, &dev->msi_list, list) { - irq = create_irq_nr(irq_want--); + list_for_each_entry(msidesc, &dev->msi_list, list) { + irq = create_irq_nr(irq_want); + irq_want--; if (irq == 0) return -1; #ifdef CONFIG_INTR_REMAP @@ -3289,7 +3357,7 @@ int arch_setup_msi_irqs(struct pci_dev *dev, int nvec, int type) } no_ir: #endif - ret = setup_msi_irq(dev, desc, irq); + ret = setup_msi_irq(dev, msidesc, irq); if (ret < 0) goto error; sub_handle++; @@ -3707,17 +3775,29 @@ int __init io_apic_get_version(int ioapic) int io_apic_set_pci_routing (int ioapic, int pin, int irq, int triggering, int polarity) { + struct irq_desc *desc; + struct irq_cfg *cfg; + int cpu = boot_cpu_id; + if (!IO_APIC_IRQ(irq)) { apic_printk(APIC_QUIET,KERN_ERR "IOAPIC[%d]: Invalid reference to IRQ 0\n", ioapic); return -EINVAL; } + desc = irq_to_desc_alloc_cpu(irq, cpu); + if (!desc) { + printk(KERN_INFO "can not get irq_desc %d\n", irq); + return 0; + } + /* * IRQs < 16 are already in the irq_2_pin[] map */ - if (irq >= 16) - add_pin_to_irq(irq, ioapic, pin); + if (irq >= 16) { + cfg = desc->chip_data; + add_pin_to_irq_cpu(irq, cpu, ioapic, pin); + } setup_IO_APIC_irq(ioapic, pin, irq, triggering, polarity); @@ -3773,7 +3853,8 @@ void __init setup_ioapic_dest(void) * when you have too many devices, because at that time only boot * cpu is online. */ - cfg = irq_cfg(irq); + desc = irq_to_desc(irq); + cfg = desc->chip_data; if (!cfg->vector) { setup_IO_APIC_irq(ioapic, pin, irq, irq_trigger(irq_entry), @@ -3785,7 +3866,6 @@ void __init setup_ioapic_dest(void) /* * Honour affinities which have been set in early boot */ - desc = irq_to_desc(irq); if (desc->status & (IRQ_NO_BALANCING | IRQ_AFFINITY_SET)) mask = desc->affinity; @@ -3846,7 +3926,6 @@ void __init ioapic_init_mappings(void) struct resource *ioapic_res; int i; - irq_2_pin_init(); ioapic_res = ioapic_setup_resources(); for (i = 0; i < nr_ioapics; i++) { if (smp_found_config) { diff --git a/arch/x86/kernel/irq.c b/arch/x86/kernel/irq.c index d1d4dc5..3f1d9d1 100644 --- a/arch/x86/kernel/irq.c +++ b/arch/x86/kernel/irq.c @@ -118,6 +118,9 @@ int show_interrupts(struct seq_file *p, void *v) } desc = irq_to_desc(i); + if (!desc) + return 0; + spin_lock_irqsave(&desc->lock, flags); #ifndef CONFIG_SMP any_count = kstat_irqs(i); diff --git a/arch/x86/kernel/irq_32.c b/arch/x86/kernel/irq_32.c index a513826..119fc9c 100644 --- a/arch/x86/kernel/irq_32.c +++ b/arch/x86/kernel/irq_32.c @@ -242,6 +242,8 @@ void fixup_irqs(cpumask_t map) for_each_irq_desc(irq, desc) { cpumask_t mask; + if (!desc) + continue; if (irq == 2) continue; diff --git a/arch/x86/kernel/irq_64.c b/arch/x86/kernel/irq_64.c index 60eb84e..900009c 100644 --- a/arch/x86/kernel/irq_64.c +++ b/arch/x86/kernel/irq_64.c @@ -94,6 +94,8 @@ void fixup_irqs(cpumask_t map) int break_affinity = 0; int set_affinity = 1; + if (!desc) + continue; if (irq == 2) continue; diff --git a/arch/x86/kernel/irqinit_32.c b/arch/x86/kernel/irqinit_32.c index 845aa98..5a5651b 100644 --- a/arch/x86/kernel/irqinit_32.c +++ b/arch/x86/kernel/irqinit_32.c @@ -69,7 +69,6 @@ void __init init_ISA_irqs (void) * 16 old-style INTA-cycle interrupts: */ for (i = 0; i < 16; i++) { - /* first time call this irq_desc */ struct irq_desc *desc = irq_to_desc(i); desc->status = IRQ_DISABLED; diff --git a/arch/x86/kernel/irqinit_64.c b/arch/x86/kernel/irqinit_64.c index ff02353..cd9f42d 100644 --- a/arch/x86/kernel/irqinit_64.c +++ b/arch/x86/kernel/irqinit_64.c @@ -143,7 +143,6 @@ void __init init_ISA_irqs(void) init_8259A(0); for (i = 0; i < 16; i++) { - /* first time call this irq_desc */ struct irq_desc *desc = irq_to_desc(i); desc->status = IRQ_DISABLED; -- cgit v1.1 From 99d093d12897562a253540a902bbf65ec16042ac Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Fri, 5 Dec 2008 18:58:32 -0800 Subject: x86: use NR_IRQS_LEGACY Impact: cleanup Introduce NR_IRQS_LEGACY instead of hard coded number. Signed-off-by: Yinghai Lu Signed-off-by: Ingo Molnar --- arch/x86/include/asm/irq_vectors.h | 2 ++ arch/x86/kernel/io_apic.c | 10 +++++----- arch/x86/kernel/irqinit_32.c | 2 +- arch/x86/kernel/irqinit_64.c | 2 +- 4 files changed, 9 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/x86/include/asm/irq_vectors.h b/arch/x86/include/asm/irq_vectors.h index bb6b69a..f7ff650 100644 --- a/arch/x86/include/asm/irq_vectors.h +++ b/arch/x86/include/asm/irq_vectors.h @@ -101,6 +101,8 @@ #define LAST_VM86_IRQ 15 #define invalid_vm86_irq(irq) ((irq) < 3 || (irq) > 15) +#define NR_IRQS_LEGACY 16 + #if defined(CONFIG_X86_IO_APIC) && !defined(CONFIG_X86_VOYAGER) #ifndef CONFIG_SPARSE_IRQ diff --git a/arch/x86/kernel/io_apic.c b/arch/x86/kernel/io_apic.c index 9de17f5..9870461 100644 --- a/arch/x86/kernel/io_apic.c +++ b/arch/x86/kernel/io_apic.c @@ -847,7 +847,7 @@ EXPORT_SYMBOL(IO_APIC_get_PCI_irq_vector); */ static int EISA_ELCR(unsigned int irq) { - if (irq < 16) { + if (irq < NR_IRQS_LEGACY) { unsigned int port = 0x4d0 + (irq >> 3); return (inb(port) >> (irq & 7)) & 1; } @@ -1388,7 +1388,7 @@ static void setup_IO_APIC_irq(int apic, int pin, unsigned int irq, } ioapic_register_intr(irq, trigger); - if (irq < 16) + if (irq < NR_IRQS_LEGACY) disable_8259A_irq(irq); ioapic_write_entry(apic, pin, entry); @@ -2080,7 +2080,7 @@ static unsigned int startup_ioapic_irq(unsigned int irq) struct irq_cfg *cfg; spin_lock_irqsave(&ioapic_lock, flags); - if (irq < 16) { + if (irq < NR_IRQS_LEGACY) { disable_8259A_irq(irq); if (i8259A_irq_pending(irq)) was_pending = 1; @@ -2504,7 +2504,7 @@ static inline void init_IO_APIC_traps(void) * so default to an old-fashioned 8259 * interrupt if we can.. */ - if (irq < 16) + if (irq < NR_IRQS_LEGACY) make_8259A_irq(irq); else /* Strange. Oh, well.. */ @@ -3794,7 +3794,7 @@ int io_apic_set_pci_routing (int ioapic, int pin, int irq, int triggering, int p /* * IRQs < 16 are already in the irq_2_pin[] map */ - if (irq >= 16) { + if (irq >= NR_IRQS_LEGACY) { cfg = desc->chip_data; add_pin_to_irq_cpu(irq, cpu, ioapic, pin); } diff --git a/arch/x86/kernel/irqinit_32.c b/arch/x86/kernel/irqinit_32.c index 5a5651b..6a92f47 100644 --- a/arch/x86/kernel/irqinit_32.c +++ b/arch/x86/kernel/irqinit_32.c @@ -68,7 +68,7 @@ void __init init_ISA_irqs (void) /* * 16 old-style INTA-cycle interrupts: */ - for (i = 0; i < 16; i++) { + for (i = 0; i < NR_IRQS_LEGACY; i++) { struct irq_desc *desc = irq_to_desc(i); desc->status = IRQ_DISABLED; diff --git a/arch/x86/kernel/irqinit_64.c b/arch/x86/kernel/irqinit_64.c index cd9f42d..40c1e62 100644 --- a/arch/x86/kernel/irqinit_64.c +++ b/arch/x86/kernel/irqinit_64.c @@ -142,7 +142,7 @@ void __init init_ISA_irqs(void) init_bsp_APIC(); init_8259A(0); - for (i = 0; i < 16; i++) { + for (i = 0; i < NR_IRQS_LEGACY; i++) { struct irq_desc *desc = irq_to_desc(i); desc->status = IRQ_DISABLED; -- cgit v1.1 From be5d5350a937cd8513b258739f1099420129e96f Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Fri, 5 Dec 2008 18:58:33 -0800 Subject: x86: MSI start irq numbering from nr_irqs_gsi Impact: sanitize MSI irq number ordering from top-down to bottom-up Increase new MSI IRQs starting from nr_irqs_gsi (which is somewhere below 256), instead of decreasing from NR_IRQS. (The latter method can result in confusingly high IRQ numbers - if NR_CPUS is set to a high value and NR_IRQS scales up to a high value.) Signed-off-by: Yinghai Lu Signed-off-by: Ingo Molnar --- arch/x86/include/asm/io_apic.h | 2 +- arch/x86/kernel/io_apic.c | 24 +++++++++++++++++------- arch/x86/kernel/setup.c | 2 +- 3 files changed, 19 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/x86/include/asm/io_apic.h b/arch/x86/include/asm/io_apic.h index 6afd993..b35e94c 100644 --- a/arch/x86/include/asm/io_apic.h +++ b/arch/x86/include/asm/io_apic.h @@ -188,7 +188,7 @@ extern void restore_IO_APIC_setup(void); extern void reinit_intr_remapped_IO_APIC(int); #endif -extern int probe_nr_irqs(void); +extern void probe_nr_irqs_gsi(void); #else /* !CONFIG_X86_IO_APIC */ #define io_apic_assign_pci_irqs 0 diff --git a/arch/x86/kernel/io_apic.c b/arch/x86/kernel/io_apic.c index 9870461..0dcde74 100644 --- a/arch/x86/kernel/io_apic.c +++ b/arch/x86/kernel/io_apic.c @@ -2973,7 +2973,7 @@ unsigned int create_irq_nr(unsigned int irq_want) irq = 0; spin_lock_irqsave(&vector_lock, flags); - for (new = irq_want; new > 0; new--) { + for (new = irq_want; new < NR_IRQS; new++) { if (platform_legacy_irq(new)) continue; @@ -3001,11 +3001,14 @@ unsigned int create_irq_nr(unsigned int irq_want) return irq; } +static int nr_irqs_gsi = NR_IRQS_LEGACY; int create_irq(void) { + unsigned int irq_want; int irq; - irq = create_irq_nr(nr_irqs - 1); + irq_want = nr_irqs_gsi; + irq = create_irq_nr(irq_want); if (irq == 0) irq = -1; @@ -3281,7 +3284,7 @@ int arch_setup_msi_irq(struct pci_dev *dev, struct msi_desc *msidesc) int ret; unsigned int irq_want; - irq_want = nr_irqs - 1; + irq_want = nr_irqs_gsi; irq = create_irq_nr(irq_want); if (irq == 0) return -1; @@ -3321,11 +3324,11 @@ int arch_setup_msi_irqs(struct pci_dev *dev, int nvec, int type) int index = 0; #endif - irq_want = nr_irqs - 1; + irq_want = nr_irqs_gsi; sub_handle = 0; list_for_each_entry(msidesc, &dev->msi_list, list) { irq = create_irq_nr(irq_want); - irq_want--; + irq_want++; if (irq == 0) return -1; #ifdef CONFIG_INTR_REMAP @@ -3674,9 +3677,16 @@ int __init io_apic_get_redir_entries (int ioapic) return reg_01.bits.entries; } -int __init probe_nr_irqs(void) +void __init probe_nr_irqs_gsi(void) { - return NR_IRQS; + int idx; + int nr = 0; + + for (idx = 0; idx < nr_ioapics; idx++) + nr += io_apic_get_redir_entries(idx) + 1; + + if (nr > nr_irqs_gsi) + nr_irqs_gsi = nr; } /* -------------------------------------------------------------------------- diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c index 9d5674f..a3834f1 100644 --- a/arch/x86/kernel/setup.c +++ b/arch/x86/kernel/setup.c @@ -1082,7 +1082,7 @@ void __init setup_arch(char **cmdline_p) ioapic_init_mappings(); /* need to wait for io_apic is mapped */ - nr_irqs = probe_nr_irqs(); + probe_nr_irqs_gsi(); kvm_guest_init(); -- cgit v1.1 From 3145e941fcfe2548fa2270afb1a05bab3a6bc418 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Fri, 5 Dec 2008 18:58:34 -0800 Subject: x86, MSI: pass irq_cfg and irq_desc Impact: simplify code Pass irq_desc and cfg around, instead of raw IRQ numbers - this way we dont have to look it up again and again. Signed-off-by: Yinghai Lu Signed-off-by: Ingo Molnar --- arch/x86/kernel/io_apic.c | 318 ++++++++++++++++++++++++++-------------------- 1 file changed, 181 insertions(+), 137 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/io_apic.c b/arch/x86/kernel/io_apic.c index 0dcde74..a1a2e07 100644 --- a/arch/x86/kernel/io_apic.c +++ b/arch/x86/kernel/io_apic.c @@ -231,6 +231,10 @@ static struct irq_cfg *irq_cfg(unsigned int irq) #endif +static inline void set_extra_move_desc(struct irq_desc *desc, cpumask_t mask) +{ +} + struct io_apic { unsigned int index; unsigned int unused[3]; @@ -272,11 +276,10 @@ static inline void io_apic_modify(unsigned int apic, unsigned int reg, unsigned writel(value, &io_apic->data); } -static bool io_apic_level_ack_pending(unsigned int irq) +static bool io_apic_level_ack_pending(struct irq_cfg *cfg) { struct irq_pin_list *entry; unsigned long flags; - struct irq_cfg *cfg = irq_cfg(irq); spin_lock_irqsave(&ioapic_lock, flags); entry = cfg->irq_2_pin; @@ -358,13 +361,12 @@ static void ioapic_mask_entry(int apic, int pin) } #ifdef CONFIG_SMP -static void __target_IO_APIC_irq(unsigned int irq, unsigned int dest, u8 vector) +static void __target_IO_APIC_irq(unsigned int irq, unsigned int dest, struct irq_cfg *cfg) { int apic, pin; - struct irq_cfg *cfg; struct irq_pin_list *entry; + u8 vector = cfg->vector; - cfg = irq_cfg(irq); entry = cfg->irq_2_pin; for (;;) { unsigned int reg; @@ -394,24 +396,27 @@ static void __target_IO_APIC_irq(unsigned int irq, unsigned int dest, u8 vector) } } -static int assign_irq_vector(int irq, cpumask_t mask); +static int assign_irq_vector(int irq, struct irq_cfg *cfg, cpumask_t mask); -static void set_ioapic_affinity_irq(unsigned int irq, cpumask_t mask) +static void set_ioapic_affinity_irq_desc(struct irq_desc *desc, cpumask_t mask) { struct irq_cfg *cfg; unsigned long flags; unsigned int dest; cpumask_t tmp; - struct irq_desc *desc; + unsigned int irq; cpus_and(tmp, mask, cpu_online_map); if (cpus_empty(tmp)) return; - cfg = irq_cfg(irq); - if (assign_irq_vector(irq, mask)) + irq = desc->irq; + cfg = desc->chip_data; + if (assign_irq_vector(irq, cfg, mask)) return; + set_extra_move_desc(desc, mask); + cpus_and(tmp, cfg->domain, mask); dest = cpu_mask_to_apicid(tmp); /* @@ -419,12 +424,20 @@ static void set_ioapic_affinity_irq(unsigned int irq, cpumask_t mask) */ dest = SET_APIC_LOGICAL_ID(dest); - desc = irq_to_desc(irq); spin_lock_irqsave(&ioapic_lock, flags); - __target_IO_APIC_irq(irq, dest, cfg->vector); + __target_IO_APIC_irq(irq, dest, cfg); desc->affinity = mask; spin_unlock_irqrestore(&ioapic_lock, flags); } + +static void set_ioapic_affinity_irq(unsigned int irq, cpumask_t mask) +{ + struct irq_desc *desc; + + desc = irq_to_desc(irq); + + set_ioapic_affinity_irq_desc(desc, mask); +} #endif /* CONFIG_SMP */ /* @@ -432,10 +445,9 @@ static void set_ioapic_affinity_irq(unsigned int irq, cpumask_t mask) * shared ISA-space IRQs, so we have to support them. We are super * fast in the common case, and fast for shared ISA-space IRQs. */ -static void add_pin_to_irq_cpu(unsigned int irq, int cpu, int apic, int pin) +static void add_pin_to_irq_cpu(struct irq_cfg *cfg, int cpu, int apic, int pin) { struct irq_pin_list *entry; - struct irq_cfg *cfg = irq_cfg(irq); entry = cfg->irq_2_pin; if (!entry) { @@ -468,11 +480,10 @@ static void add_pin_to_irq_cpu(unsigned int irq, int cpu, int apic, int pin) /* * Reroute an IRQ to a different pin. */ -static void __init replace_pin_at_irq(unsigned int irq, int cpu, +static void __init replace_pin_at_irq_cpu(struct irq_cfg *cfg, int cpu, int oldapic, int oldpin, int newapic, int newpin) { - struct irq_cfg *cfg = irq_cfg(irq); struct irq_pin_list *entry = cfg->irq_2_pin; int replaced = 0; @@ -489,18 +500,16 @@ static void __init replace_pin_at_irq(unsigned int irq, int cpu, /* why? call replace before add? */ if (!replaced) - add_pin_to_irq_cpu(irq, cpu, newapic, newpin); + add_pin_to_irq_cpu(cfg, cpu, newapic, newpin); } -static inline void io_apic_modify_irq(unsigned int irq, +static inline void io_apic_modify_irq(struct irq_cfg *cfg, int mask_and, int mask_or, void (*final)(struct irq_pin_list *entry)) { int pin; - struct irq_cfg *cfg; struct irq_pin_list *entry; - cfg = irq_cfg(irq); for (entry = cfg->irq_2_pin; entry != NULL; entry = entry->next) { unsigned int reg; pin = entry->pin; @@ -513,9 +522,9 @@ static inline void io_apic_modify_irq(unsigned int irq, } } -static void __unmask_IO_APIC_irq(unsigned int irq) +static void __unmask_IO_APIC_irq(struct irq_cfg *cfg) { - io_apic_modify_irq(irq, ~IO_APIC_REDIR_MASKED, 0, NULL); + io_apic_modify_irq(cfg, ~IO_APIC_REDIR_MASKED, 0, NULL); } #ifdef CONFIG_X86_64 @@ -530,47 +539,64 @@ void io_apic_sync(struct irq_pin_list *entry) readl(&io_apic->data); } -static void __mask_IO_APIC_irq(unsigned int irq) +static void __mask_IO_APIC_irq(struct irq_cfg *cfg) { - io_apic_modify_irq(irq, ~0, IO_APIC_REDIR_MASKED, &io_apic_sync); + io_apic_modify_irq(cfg, ~0, IO_APIC_REDIR_MASKED, &io_apic_sync); } #else /* CONFIG_X86_32 */ -static void __mask_IO_APIC_irq(unsigned int irq) +static void __mask_IO_APIC_irq(struct irq_cfg *cfg) { - io_apic_modify_irq(irq, ~0, IO_APIC_REDIR_MASKED, NULL); + io_apic_modify_irq(cfg, ~0, IO_APIC_REDIR_MASKED, NULL); } -static void __mask_and_edge_IO_APIC_irq(unsigned int irq) +static void __mask_and_edge_IO_APIC_irq(struct irq_cfg *cfg) { - io_apic_modify_irq(irq, ~IO_APIC_REDIR_LEVEL_TRIGGER, + io_apic_modify_irq(cfg, ~IO_APIC_REDIR_LEVEL_TRIGGER, IO_APIC_REDIR_MASKED, NULL); } -static void __unmask_and_level_IO_APIC_irq(unsigned int irq) +static void __unmask_and_level_IO_APIC_irq(struct irq_cfg *cfg) { - io_apic_modify_irq(irq, ~IO_APIC_REDIR_MASKED, + io_apic_modify_irq(cfg, ~IO_APIC_REDIR_MASKED, IO_APIC_REDIR_LEVEL_TRIGGER, NULL); } #endif /* CONFIG_X86_32 */ -static void mask_IO_APIC_irq (unsigned int irq) +static void mask_IO_APIC_irq_desc(struct irq_desc *desc) { + struct irq_cfg *cfg = desc->chip_data; unsigned long flags; + BUG_ON(!cfg); + spin_lock_irqsave(&ioapic_lock, flags); - __mask_IO_APIC_irq(irq); + __mask_IO_APIC_irq(cfg); spin_unlock_irqrestore(&ioapic_lock, flags); } -static void unmask_IO_APIC_irq (unsigned int irq) +static void unmask_IO_APIC_irq_desc(struct irq_desc *desc) { + struct irq_cfg *cfg = desc->chip_data; unsigned long flags; spin_lock_irqsave(&ioapic_lock, flags); - __unmask_IO_APIC_irq(irq); + __unmask_IO_APIC_irq(cfg); spin_unlock_irqrestore(&ioapic_lock, flags); } +static void mask_IO_APIC_irq(unsigned int irq) +{ + struct irq_desc *desc = irq_to_desc(irq); + + mask_IO_APIC_irq_desc(desc); +} +static void unmask_IO_APIC_irq(unsigned int irq) +{ + struct irq_desc *desc = irq_to_desc(irq); + + unmask_IO_APIC_irq_desc(desc); +} + static void clear_IO_APIC_pin(unsigned int apic, unsigned int pin) { struct IO_APIC_route_entry entry; @@ -1072,7 +1098,7 @@ void unlock_vector_lock(void) spin_unlock(&vector_lock); } -static int __assign_irq_vector(int irq, cpumask_t mask) +static int __assign_irq_vector(int irq, struct irq_cfg *cfg, cpumask_t mask) { /* * NOTE! The local APIC isn't very good at handling @@ -1088,16 +1114,13 @@ static int __assign_irq_vector(int irq, cpumask_t mask) static int current_vector = FIRST_DEVICE_VECTOR, current_offset = 0; unsigned int old_vector; int cpu; - struct irq_cfg *cfg; - cfg = irq_cfg(irq); + if ((cfg->move_in_progress) || cfg->move_cleanup_count) + return -EBUSY; /* Only try and allocate irqs on cpus that are present */ cpus_and(mask, mask, cpu_online_map); - if ((cfg->move_in_progress) || cfg->move_cleanup_count) - return -EBUSY; - old_vector = cfg->vector; if (old_vector) { cpumask_t tmp; @@ -1151,24 +1174,22 @@ next: return -ENOSPC; } -static int assign_irq_vector(int irq, cpumask_t mask) +static int assign_irq_vector(int irq, struct irq_cfg *cfg, cpumask_t mask) { int err; unsigned long flags; spin_lock_irqsave(&vector_lock, flags); - err = __assign_irq_vector(irq, mask); + err = __assign_irq_vector(irq, cfg, mask); spin_unlock_irqrestore(&vector_lock, flags); return err; } -static void __clear_irq_vector(int irq) +static void __clear_irq_vector(int irq, struct irq_cfg *cfg) { - struct irq_cfg *cfg; cpumask_t mask; int cpu, vector; - cfg = irq_cfg(irq); BUG_ON(!cfg->vector); vector = cfg->vector; @@ -1257,11 +1278,8 @@ static inline int IO_APIC_irq_trigger(int irq) } #endif -static void ioapic_register_intr(int irq, unsigned long trigger) +static void ioapic_register_intr(int irq, struct irq_desc *desc, unsigned long trigger) { - struct irq_desc *desc; - - desc = irq_to_desc(irq); if ((trigger == IOAPIC_AUTO && IO_APIC_irq_trigger(irq)) || trigger == IOAPIC_LEVEL) @@ -1353,7 +1371,7 @@ static int setup_ioapic_entry(int apic, int irq, return 0; } -static void setup_IO_APIC_irq(int apic, int pin, unsigned int irq, +static void setup_IO_APIC_irq(int apic, int pin, unsigned int irq, struct irq_desc *desc, int trigger, int polarity) { struct irq_cfg *cfg; @@ -1363,10 +1381,10 @@ static void setup_IO_APIC_irq(int apic, int pin, unsigned int irq, if (!IO_APIC_IRQ(irq)) return; - cfg = irq_cfg(irq); + cfg = desc->chip_data; mask = TARGET_CPUS; - if (assign_irq_vector(irq, mask)) + if (assign_irq_vector(irq, cfg, mask)) return; cpus_and(mask, cfg->domain, mask); @@ -1383,11 +1401,11 @@ static void setup_IO_APIC_irq(int apic, int pin, unsigned int irq, cfg->vector)) { printk("Failed to setup ioapic entry for ioapic %d, pin %d\n", mp_ioapics[apic].mp_apicid, pin); - __clear_irq_vector(irq); + __clear_irq_vector(irq, cfg); return; } - ioapic_register_intr(irq, trigger); + ioapic_register_intr(irq, desc, trigger); if (irq < NR_IRQS_LEGACY) disable_8259A_irq(irq); @@ -1399,6 +1417,7 @@ static void __init setup_IO_APIC_irqs(void) int apic, pin, idx, irq; int notcon = 0; struct irq_desc *desc; + struct irq_cfg *cfg; int cpu = boot_cpu_id; apic_printk(APIC_VERBOSE, KERN_DEBUG "init IO_APIC IRQs\n"); @@ -1436,9 +1455,10 @@ static void __init setup_IO_APIC_irqs(void) printk(KERN_INFO "can not get irq_desc for %d\n", irq); continue; } - add_pin_to_irq_cpu(irq, cpu, apic, pin); + cfg = desc->chip_data; + add_pin_to_irq_cpu(cfg, cpu, apic, pin); - setup_IO_APIC_irq(apic, pin, irq, + setup_IO_APIC_irq(apic, pin, irq, desc, irq_trigger(idx), irq_polarity(idx)); } } @@ -2086,7 +2106,7 @@ static unsigned int startup_ioapic_irq(unsigned int irq) was_pending = 1; } cfg = irq_cfg(irq); - __unmask_IO_APIC_irq(irq); + __unmask_IO_APIC_irq(cfg); spin_unlock_irqrestore(&ioapic_lock, flags); return was_pending; @@ -2149,35 +2169,37 @@ static DECLARE_DELAYED_WORK(ir_migration_work, ir_irq_migration); * as simple as edge triggered migration and we can do the irq migration * with a simple atomic update to IO-APIC RTE. */ -static void migrate_ioapic_irq(int irq, cpumask_t mask) +static void migrate_ioapic_irq_desc(struct irq_desc *desc, cpumask_t mask) { struct irq_cfg *cfg; - struct irq_desc *desc; cpumask_t tmp, cleanup_mask; struct irte irte; int modify_ioapic_rte; unsigned int dest; unsigned long flags; + unsigned int irq; cpus_and(tmp, mask, cpu_online_map); if (cpus_empty(tmp)) return; + irq = desc->irq; if (get_irte(irq, &irte)) return; - if (assign_irq_vector(irq, mask)) + cfg = desc->chip_data; + if (assign_irq_vector(irq, cfg, mask)) return; - cfg = irq_cfg(irq); + set_extra_move_desc(desc, mask); + cpus_and(tmp, cfg->domain, mask); dest = cpu_mask_to_apicid(tmp); - desc = irq_to_desc(irq); modify_ioapic_rte = desc->status & IRQ_LEVEL; if (modify_ioapic_rte) { spin_lock_irqsave(&ioapic_lock, flags); - __target_IO_APIC_irq(irq, dest, cfg->vector); + __target_IO_APIC_irq(irq, dest, cfg); spin_unlock_irqrestore(&ioapic_lock, flags); } @@ -2199,14 +2221,14 @@ static void migrate_ioapic_irq(int irq, cpumask_t mask) desc->affinity = mask; } -static int migrate_irq_remapped_level(int irq) +static int migrate_irq_remapped_level_desc(struct irq_desc *desc) { int ret = -1; - struct irq_desc *desc = irq_to_desc(irq); + struct irq_cfg *cfg = desc->chip_data; - mask_IO_APIC_irq(irq); + mask_IO_APIC_irq_desc(desc); - if (io_apic_level_ack_pending(irq)) { + if (io_apic_level_ack_pending(cfg)) { /* * Interrupt in progress. Migrating irq now will change the * vector information in the IO-APIC RTE and that will confuse @@ -2218,14 +2240,15 @@ static int migrate_irq_remapped_level(int irq) } /* everthing is clear. we have right of way */ - migrate_ioapic_irq(irq, desc->pending_mask); + migrate_ioapic_irq_desc(desc, desc->pending_mask); ret = 0; desc->status &= ~IRQ_MOVE_PENDING; cpus_clear(desc->pending_mask); unmask: - unmask_IO_APIC_irq(irq); + unmask_IO_APIC_irq_desc(desc); + return ret; } @@ -2258,18 +2281,22 @@ static void ir_irq_migration(struct work_struct *work) /* * Migrates the IRQ destination in the process context. */ -static void set_ir_ioapic_affinity_irq(unsigned int irq, cpumask_t mask) +static void set_ir_ioapic_affinity_irq_desc(struct irq_desc *desc, cpumask_t mask) { - struct irq_desc *desc = irq_to_desc(irq); - if (desc->status & IRQ_LEVEL) { desc->status |= IRQ_MOVE_PENDING; desc->pending_mask = mask; - migrate_irq_remapped_level(irq); + migrate_irq_remapped_level_desc(desc); return; } - migrate_ioapic_irq(irq, mask); + migrate_ioapic_irq_desc(desc, mask); +} +static void set_ir_ioapic_affinity_irq(unsigned int irq, cpumask_t mask) +{ + struct irq_desc *desc = irq_to_desc(irq); + + set_ir_ioapic_affinity_irq_desc(desc, mask); } #endif @@ -2313,9 +2340,10 @@ unlock: irq_exit(); } -static void irq_complete_move(unsigned int irq) +static void irq_complete_move(struct irq_desc **descp) { - struct irq_cfg *cfg = irq_cfg(irq); + struct irq_desc *desc = *descp; + struct irq_cfg *cfg = desc->chip_data; unsigned vector, me; if (likely(!cfg->move_in_progress)) @@ -2333,8 +2361,9 @@ static void irq_complete_move(unsigned int irq) } } #else -static inline void irq_complete_move(unsigned int irq) {} +static inline void irq_complete_move(struct irq_desc **descp) {} #endif + #ifdef CONFIG_INTR_REMAP static void ack_x2apic_level(unsigned int irq) { @@ -2345,11 +2374,14 @@ static void ack_x2apic_edge(unsigned int irq) { ack_x2APIC_irq(); } + #endif static void ack_apic_edge(unsigned int irq) { - irq_complete_move(irq); + struct irq_desc *desc = irq_to_desc(irq); + + irq_complete_move(&desc); move_native_irq(irq); ack_APIC_irq(); } @@ -2358,18 +2390,21 @@ atomic_t irq_mis_count; static void ack_apic_level(unsigned int irq) { + struct irq_desc *desc = irq_to_desc(irq); + #ifdef CONFIG_X86_32 unsigned long v; int i; #endif + struct irq_cfg *cfg; int do_unmask_irq = 0; - irq_complete_move(irq); + irq_complete_move(&desc); #ifdef CONFIG_GENERIC_PENDING_IRQ /* If we are moving the irq we need to mask it */ - if (unlikely(irq_to_desc(irq)->status & IRQ_MOVE_PENDING)) { + if (unlikely(desc->status & IRQ_MOVE_PENDING)) { do_unmask_irq = 1; - mask_IO_APIC_irq(irq); + mask_IO_APIC_irq_desc(desc); } #endif @@ -2393,7 +2428,8 @@ static void ack_apic_level(unsigned int irq) * operation to prevent an edge-triggered interrupt escaping meanwhile. * The idea is from Manfred Spraul. --macro */ - i = irq_cfg(irq)->vector; + cfg = desc->chip_data; + i = cfg->vector; v = apic_read(APIC_TMR + ((i & ~0x1f) >> 1)); #endif @@ -2432,17 +2468,18 @@ static void ack_apic_level(unsigned int irq) * accurate and is causing problems then it is a hardware bug * and you can go talk to the chipset vendor about it. */ - if (!io_apic_level_ack_pending(irq)) + cfg = desc->chip_data; + if (!io_apic_level_ack_pending(cfg)) move_masked_irq(irq); - unmask_IO_APIC_irq(irq); + unmask_IO_APIC_irq_desc(desc); } #ifdef CONFIG_X86_32 if (!(v & (1 << (i & 0x1f)))) { atomic_inc(&irq_mis_count); spin_lock(&ioapic_lock); - __mask_and_edge_IO_APIC_irq(irq); - __unmask_and_level_IO_APIC_irq(irq); + __mask_and_edge_IO_APIC_irq(cfg); + __unmask_and_level_IO_APIC_irq(cfg); spin_unlock(&ioapic_lock); } #endif @@ -2533,7 +2570,7 @@ static void unmask_lapic_irq(unsigned int irq) apic_write(APIC_LVT0, v & ~APIC_LVT_MASKED); } -static void ack_lapic_irq (unsigned int irq) +static void ack_lapic_irq(unsigned int irq) { ack_APIC_irq(); } @@ -2545,11 +2582,8 @@ static struct irq_chip lapic_chip __read_mostly = { .ack = ack_lapic_irq, }; -static void lapic_register_intr(int irq) +static void lapic_register_intr(int irq, struct irq_desc *desc) { - struct irq_desc *desc; - - desc = irq_to_desc(irq); desc->status &= ~IRQ_LEVEL; set_irq_chip_and_handler_name(irq, &lapic_chip, handle_edge_irq, "edge"); @@ -2653,7 +2687,9 @@ int timer_through_8259 __initdata; */ static inline void __init check_timer(void) { - struct irq_cfg *cfg = irq_cfg(0); + struct irq_desc *desc = irq_to_desc(0); + struct irq_cfg *cfg = desc->chip_data; + int cpu = boot_cpu_id; int apic1, pin1, apic2, pin2; unsigned long flags; unsigned int ver; @@ -2668,7 +2704,7 @@ static inline void __init check_timer(void) * get/set the timer IRQ vector: */ disable_8259A_irq(0); - assign_irq_vector(0, TARGET_CPUS); + assign_irq_vector(0, cfg, TARGET_CPUS); /* * As IRQ0 is to be enabled in the 8259A, the virtual @@ -2719,10 +2755,10 @@ static inline void __init check_timer(void) * Ok, does IRQ0 through the IOAPIC work? */ if (no_pin1) { - add_pin_to_irq_cpu(0, boot_cpu_id, apic1, pin1); + add_pin_to_irq_cpu(cfg, cpu, apic1, pin1); setup_timer_IRQ0_pin(apic1, pin1, cfg->vector); } - unmask_IO_APIC_irq(0); + unmask_IO_APIC_irq_desc(desc); if (timer_irq_works()) { if (nmi_watchdog == NMI_IO_APIC) { setup_nmi(); @@ -2748,9 +2784,9 @@ static inline void __init check_timer(void) /* * legacy devices should be connected to IO APIC #0 */ - replace_pin_at_irq(0, boot_cpu_id, apic1, pin1, apic2, pin2); + replace_pin_at_irq_cpu(cfg, cpu, apic1, pin1, apic2, pin2); setup_timer_IRQ0_pin(apic2, pin2, cfg->vector); - unmask_IO_APIC_irq(0); + unmask_IO_APIC_irq_desc(desc); enable_8259A_irq(0); if (timer_irq_works()) { apic_printk(APIC_QUIET, KERN_INFO "....... works.\n"); @@ -2782,7 +2818,7 @@ static inline void __init check_timer(void) apic_printk(APIC_QUIET, KERN_INFO "...trying to set up timer as Virtual Wire IRQ...\n"); - lapic_register_intr(0); + lapic_register_intr(0, desc); apic_write(APIC_LVT0, APIC_DM_FIXED | cfg->vector); /* Fixed mode */ enable_8259A_irq(0); @@ -2986,7 +3022,7 @@ unsigned int create_irq_nr(unsigned int irq_want) if (cfg_new->vector != 0) continue; - if (__assign_irq_vector(new, TARGET_CPUS) == 0) + if (__assign_irq_vector(new, cfg_new, TARGET_CPUS) == 0) irq = new; break; } @@ -3034,7 +3070,7 @@ void destroy_irq(unsigned int irq) free_irte(irq); #endif spin_lock_irqsave(&vector_lock, flags); - __clear_irq_vector(irq); + __clear_irq_vector(irq, cfg); spin_unlock_irqrestore(&vector_lock, flags); } @@ -3049,12 +3085,12 @@ static int msi_compose_msg(struct pci_dev *pdev, unsigned int irq, struct msi_ms unsigned dest; cpumask_t tmp; + cfg = irq_cfg(irq); tmp = TARGET_CPUS; - err = assign_irq_vector(irq, tmp); + err = assign_irq_vector(irq, cfg, tmp); if (err) return err; - cfg = irq_cfg(irq); cpus_and(tmp, cfg->domain, tmp); dest = cpu_mask_to_apicid(tmp); @@ -3112,35 +3148,35 @@ static int msi_compose_msg(struct pci_dev *pdev, unsigned int irq, struct msi_ms #ifdef CONFIG_SMP static void set_msi_irq_affinity(unsigned int irq, cpumask_t mask) { + struct irq_desc *desc = irq_to_desc(irq); struct irq_cfg *cfg; struct msi_msg msg; unsigned int dest; cpumask_t tmp; - struct irq_desc *desc; cpus_and(tmp, mask, cpu_online_map); if (cpus_empty(tmp)) return; - if (assign_irq_vector(irq, mask)) + cfg = desc->chip_data; + if (assign_irq_vector(irq, cfg, mask)) return; - cfg = irq_cfg(irq); + set_extra_move_desc(desc, mask); + cpus_and(tmp, cfg->domain, mask); dest = cpu_mask_to_apicid(tmp); - read_msi_msg(irq, &msg); + read_msi_msg_desc(desc, &msg); msg.data &= ~MSI_DATA_VECTOR_MASK; msg.data |= MSI_DATA_VECTOR(cfg->vector); msg.address_lo &= ~MSI_ADDR_DEST_ID_MASK; msg.address_lo |= MSI_ADDR_DEST_ID(dest); - write_msi_msg(irq, &msg); - desc = irq_to_desc(irq); + write_msi_msg_desc(desc, &msg); desc->affinity = mask; } - #ifdef CONFIG_INTR_REMAP /* * Migrate the MSI irq to another cpumask. This migration is @@ -3148,11 +3184,11 @@ static void set_msi_irq_affinity(unsigned int irq, cpumask_t mask) */ static void ir_set_msi_irq_affinity(unsigned int irq, cpumask_t mask) { + struct irq_desc *desc = irq_to_desc(irq); struct irq_cfg *cfg; unsigned int dest; cpumask_t tmp, cleanup_mask; struct irte irte; - struct irq_desc *desc; cpus_and(tmp, mask, cpu_online_map); if (cpus_empty(tmp)) @@ -3161,10 +3197,12 @@ static void ir_set_msi_irq_affinity(unsigned int irq, cpumask_t mask) if (get_irte(irq, &irte)) return; - if (assign_irq_vector(irq, mask)) + cfg = desc->chip_data; + if (assign_irq_vector(irq, cfg, mask)) return; - cfg = irq_cfg(irq); + set_extra_move_desc(desc, mask); + cpus_and(tmp, cfg->domain, mask); dest = cpu_mask_to_apicid(tmp); @@ -3188,9 +3226,9 @@ static void ir_set_msi_irq_affinity(unsigned int irq, cpumask_t mask) cfg->move_in_progress = 0; } - desc = irq_to_desc(irq); desc->affinity = mask; } + #endif #endif /* CONFIG_SMP */ @@ -3249,7 +3287,7 @@ static int msi_alloc_irte(struct pci_dev *dev, int irq, int nvec) } #endif -static int setup_msi_irq(struct pci_dev *dev, struct msi_desc *desc, int irq) +static int setup_msi_irq(struct pci_dev *dev, struct msi_desc *msidesc, int irq) { int ret; struct msi_msg msg; @@ -3258,7 +3296,7 @@ static int setup_msi_irq(struct pci_dev *dev, struct msi_desc *desc, int irq) if (ret < 0) return ret; - set_irq_msi(irq, desc); + set_irq_msi(irq, msidesc); write_msi_msg(irq, &msg); #ifdef CONFIG_INTR_REMAP @@ -3381,20 +3419,22 @@ void arch_teardown_msi_irq(unsigned int irq) #ifdef CONFIG_SMP static void dmar_msi_set_affinity(unsigned int irq, cpumask_t mask) { + struct irq_desc *desc = irq_to_desc(irq); struct irq_cfg *cfg; struct msi_msg msg; unsigned int dest; cpumask_t tmp; - struct irq_desc *desc; cpus_and(tmp, mask, cpu_online_map); if (cpus_empty(tmp)) return; - if (assign_irq_vector(irq, mask)) + cfg = desc->chip_data; + if (assign_irq_vector(irq, cfg, mask)) return; - cfg = irq_cfg(irq); + set_extra_move_desc(desc, mask); + cpus_and(tmp, cfg->domain, mask); dest = cpu_mask_to_apicid(tmp); @@ -3406,9 +3446,9 @@ static void dmar_msi_set_affinity(unsigned int irq, cpumask_t mask) msg.address_lo |= MSI_ADDR_DEST_ID(dest); dmar_msi_write(irq, &msg); - desc = irq_to_desc(irq); desc->affinity = mask; } + #endif /* CONFIG_SMP */ struct irq_chip dmar_msi_type = { @@ -3442,8 +3482,8 @@ int arch_setup_dmar_msi(unsigned int irq) #ifdef CONFIG_SMP static void hpet_msi_set_affinity(unsigned int irq, cpumask_t mask) { + struct irq_desc *desc = irq_to_desc(irq); struct irq_cfg *cfg; - struct irq_desc *desc; struct msi_msg msg; unsigned int dest; cpumask_t tmp; @@ -3452,10 +3492,12 @@ static void hpet_msi_set_affinity(unsigned int irq, cpumask_t mask) if (cpus_empty(tmp)) return; - if (assign_irq_vector(irq, mask)) + cfg = desc->chip_data; + if (assign_irq_vector(irq, cfg, mask)) return; - cfg = irq_cfg(irq); + set_extra_move_desc(desc, mask); + cpus_and(tmp, cfg->domain, mask); dest = cpu_mask_to_apicid(tmp); @@ -3467,9 +3509,9 @@ static void hpet_msi_set_affinity(unsigned int irq, cpumask_t mask) msg.address_lo |= MSI_ADDR_DEST_ID(dest); hpet_msi_write(irq, &msg); - desc = irq_to_desc(irq); desc->affinity = mask; } + #endif /* CONFIG_SMP */ struct irq_chip hpet_msi_type = { @@ -3524,26 +3566,28 @@ static void target_ht_irq(unsigned int irq, unsigned int dest, u8 vector) static void set_ht_irq_affinity(unsigned int irq, cpumask_t mask) { + struct irq_desc *desc = irq_to_desc(irq); struct irq_cfg *cfg; unsigned int dest; cpumask_t tmp; - struct irq_desc *desc; cpus_and(tmp, mask, cpu_online_map); if (cpus_empty(tmp)) return; - if (assign_irq_vector(irq, mask)) + cfg = desc->chip_data; + if (assign_irq_vector(irq, cfg, mask)) return; - cfg = irq_cfg(irq); + set_extra_move_desc(desc, mask); + cpus_and(tmp, cfg->domain, mask); dest = cpu_mask_to_apicid(tmp); target_ht_irq(irq, dest, cfg->vector); - desc = irq_to_desc(irq); desc->affinity = mask; } + #endif static struct irq_chip ht_irq_chip = { @@ -3563,13 +3607,13 @@ int arch_setup_ht_irq(unsigned int irq, struct pci_dev *dev) int err; cpumask_t tmp; + cfg = irq_cfg(irq); tmp = TARGET_CPUS; - err = assign_irq_vector(irq, tmp); + err = assign_irq_vector(irq, cfg, tmp); if (!err) { struct ht_irq_msg msg; unsigned dest; - cfg = irq_cfg(irq); cpus_and(tmp, cfg->domain, tmp); dest = cpu_mask_to_apicid(tmp); @@ -3615,7 +3659,9 @@ int arch_enable_uv_irq(char *irq_name, unsigned int irq, int cpu, int mmr_blade, unsigned long flags; int err; - err = assign_irq_vector(irq, *eligible_cpu); + cfg = irq_cfg(irq); + + err = assign_irq_vector(irq, cfg, *eligible_cpu); if (err != 0) return err; @@ -3624,8 +3670,6 @@ int arch_enable_uv_irq(char *irq_name, unsigned int irq, int cpu, int mmr_blade, irq_name); spin_unlock_irqrestore(&vector_lock, flags); - cfg = irq_cfg(irq); - mmr_value = 0; entry = (struct uv_IO_APIC_route_entry *)&mmr_value; BUG_ON(sizeof(struct uv_IO_APIC_route_entry) != sizeof(unsigned long)); @@ -3806,10 +3850,10 @@ int io_apic_set_pci_routing (int ioapic, int pin, int irq, int triggering, int p */ if (irq >= NR_IRQS_LEGACY) { cfg = desc->chip_data; - add_pin_to_irq_cpu(irq, cpu, ioapic, pin); + add_pin_to_irq_cpu(cfg, cpu, ioapic, pin); } - setup_IO_APIC_irq(ioapic, pin, irq, triggering, polarity); + setup_IO_APIC_irq(ioapic, pin, irq, desc, triggering, polarity); return 0; } @@ -3866,7 +3910,7 @@ void __init setup_ioapic_dest(void) desc = irq_to_desc(irq); cfg = desc->chip_data; if (!cfg->vector) { - setup_IO_APIC_irq(ioapic, pin, irq, + setup_IO_APIC_irq(ioapic, pin, irq, desc, irq_trigger(irq_entry), irq_polarity(irq_entry)); continue; @@ -3884,10 +3928,10 @@ void __init setup_ioapic_dest(void) #ifdef CONFIG_INTR_REMAP if (intr_remapping_enabled) - set_ir_ioapic_affinity_irq(irq, mask); + set_ir_ioapic_affinity_irq_desc(desc, mask); else #endif - set_ioapic_affinity_irq(irq, mask); + set_ioapic_affinity_irq_desc(desc, mask); } } -- cgit v1.1 From bb9d4ff80bc032d7961815c2ff5eaf458ae3adff Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Thu, 4 Dec 2008 15:59:48 +0100 Subject: AMD IOMMU: fix iommu_map_page function Impact: bugfix in iommu_map_page function Signed-off-by: Joerg Roedel --- arch/x86/kernel/amd_iommu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index 5662e22..67970a8 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -344,7 +344,7 @@ static int iommu_map(struct protection_domain *dom, u64 __pte, *pte, *page; bus_addr = PAGE_ALIGN(bus_addr); - phys_addr = PAGE_ALIGN(bus_addr); + phys_addr = PAGE_ALIGN(phys_addr); /* only support 512GB address spaces for now */ if (bus_addr > IOMMU_MAP_SIZE_L3 || !(prot & IOMMU_PROT_MASK)) -- cgit v1.1 From 3cc3d84bffbd93bdb671ac7961b12cd98fbb9266 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Thu, 4 Dec 2008 16:44:31 +0100 Subject: AMD IOMMU: fix loop counter in free_pagetable function Impact: bugfix Signed-off-by: Joerg Roedel --- arch/x86/kernel/amd_iommu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index 67970a8..0637e65 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -600,7 +600,7 @@ static void dma_ops_free_pagetable(struct dma_ops_domain *dma_dom) continue; p2 = IOMMU_PTE_PAGE(p1[i]); - for (j = 0; j < 512; ++i) { + for (j = 0; j < 512; ++j) { if (!IOMMU_PTE_PRESENT(p2[j])) continue; p3 = IOMMU_PTE_PAGE(p2[j]); -- cgit v1.1 From 24f811603e8ef4b9173f47fa263230168e237128 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Mon, 8 Dec 2008 14:25:39 +0100 Subject: AMD IOMMU: fix typo in comment Impact: cleanup Signed-off-by: Joerg Roedel --- arch/x86/kernel/amd_iommu.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index 0637e65..2fde073 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -922,8 +922,8 @@ static void dma_ops_domain_unmap(struct amd_iommu *iommu, /* * This function contains common code for mapping of a physically - * contiguous memory region into DMA address space. It is uses by all - * mapping functions provided by this IOMMU driver. + * contiguous memory region into DMA address space. It is used by all + * mapping functions provided with this IOMMU driver. * Must be called with the domain lock held. */ static dma_addr_t __map_single(struct device *dev, -- cgit v1.1 From 8ad909c4c1b91bd35ba6a2af5e7ab3fc8d9fe283 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Mon, 8 Dec 2008 14:37:20 +0100 Subject: AMD IOMMU: fix WARN_ON in dma_ops unmap path Impact: minor fix Signed-off-by: Joerg Roedel --- arch/x86/kernel/amd_iommu.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index 2fde073..3133a0e 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -910,7 +910,7 @@ static void dma_ops_domain_unmap(struct amd_iommu *iommu, if (address >= dom->aperture_size) return; - WARN_ON(address & 0xfffULL || address > dom->aperture_size); + WARN_ON(address & ~PAGE_MASK || address >= dom->aperture_size); pte = dom->pte_pages[IOMMU_PTE_L1_INDEX(address)]; pte += IOMMU_PTE_L0_INDEX(address); -- cgit v1.1 From b8d9905d025d80a2357e8ce4704fde2923f6a1bd Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Mon, 8 Dec 2008 14:40:26 +0100 Subject: AMD IOMMU: __unmap_single: check for bad_dma_address instead of 0 Impact: minor fix Signed-off-by: Joerg Roedel --- arch/x86/kernel/amd_iommu.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index 3133a0e..a7b6dec 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -983,7 +983,8 @@ static void __unmap_single(struct amd_iommu *iommu, dma_addr_t i, start; unsigned int pages; - if ((dma_addr == 0) || (dma_addr + size > dma_dom->aperture_size)) + if ((dma_addr == bad_dma_address) || + (dma_addr + size > dma_dom->aperture_size)) return; pages = iommu_num_pages(dma_addr, size, PAGE_SIZE); -- cgit v1.1 From 087052b02f42b50316c6e4d7f2d8dfba3de6fc2e Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Fri, 17 Oct 2008 16:09:57 +0200 Subject: x86: fix default_spin_lock_flags() prototype MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit these warnings: arch/x86/kernel/paravirt-spinlocks.c: In function ‘default_spin_lock_flags’: arch/x86/kernel/paravirt-spinlocks.c:12: warning: passing argument 1 of ‘__raw_spin_lock’ from incompatible pointer type arch/x86/kernel/paravirt-spinlocks.c: At top level: arch/x86/kernel/paravirt-spinlocks.c:11: warning: ‘default_spin_lock_flags’ defined but not used showed that the prototype of default_spin_lock_flags() was confused about what type spinlocks have. the proper type on UP is raw_spinlock_t. Signed-off-by: Ingo Molnar --- arch/x86/kernel/paravirt-spinlocks.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/paravirt-spinlocks.c b/arch/x86/kernel/paravirt-spinlocks.c index 0e9f198..95777b0 100644 --- a/arch/x86/kernel/paravirt-spinlocks.c +++ b/arch/x86/kernel/paravirt-spinlocks.c @@ -7,7 +7,8 @@ #include -static void default_spin_lock_flags(struct raw_spinlock *lock, unsigned long flags) +static inline void +default_spin_lock_flags(raw_spinlock_t *lock, unsigned long flags) { __raw_spin_lock(lock); } -- cgit v1.1 From 50dd94e017ec39f85c26b6c10ed9fb2d7a7d8042 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Mon, 8 Dec 2008 18:47:51 +0100 Subject: sparseirq: fix typo in !CONFIG_IO_APIC case Impact: build fix Signed-off-by: Ingo Molnar --- arch/x86/include/asm/io_apic.h | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/x86/include/asm/io_apic.h b/arch/x86/include/asm/io_apic.h index b35e94c..25d527c 100644 --- a/arch/x86/include/asm/io_apic.h +++ b/arch/x86/include/asm/io_apic.h @@ -193,12 +193,9 @@ extern void probe_nr_irqs_gsi(void); #else /* !CONFIG_X86_IO_APIC */ #define io_apic_assign_pci_irqs 0 static const int timer_through_8259 = 0; -static inline void ioapic_init_mappings(void) { } +static inline void ioapic_init_mappings(void) { } -static inline int probe_nr_irqs(void) -{ - return NR_IRQS; -} +static inline void probe_nr_irqs_gsi(void) { } #endif #endif /* _ASM_X86_IO_APIC_H */ -- cgit v1.1 From fc10212583996e248dde1da74cfeccd2f7e6b675 Mon Sep 17 00:00:00 2001 From: Alexey Dobriyan Date: Tue, 9 Dec 2008 10:01:26 -0800 Subject: [IA64] remove BUILD_BUG_ON from paravirt_getreg() CC arch/ia64/kernel/asm-offsets.s In file included from include/linux/bitops.h:17, from include/linux/kernel.h:15, from include/linux/sched.h:52, from arch/ia64/kernel/asm-offsets.c:9: arch/ia64/include/asm/bitops.h: In function 'set_bit': arch/ia64/include/asm/bitops.h:47: error: implicit declaration of function 'BUILD_BUG_ON' Obvious inclusion of kernel.h doesn't fix it, because of circular dependencies involving fls.h and log2(). Fixing the latter requires some serious header surgery, it seems, so just remove BUILD_BUG_ON for now. Signed-off-by: Alexey Dobriyan Signed-off-by: Tony Luck --- arch/ia64/include/asm/paravirt_privop.h | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/ia64/include/asm/paravirt_privop.h b/arch/ia64/include/asm/paravirt_privop.h index 0b59742..33c8e55 100644 --- a/arch/ia64/include/asm/paravirt_privop.h +++ b/arch/ia64/include/asm/paravirt_privop.h @@ -83,7 +83,6 @@ extern unsigned long ia64_native_getreg_func(int regnum); #define paravirt_getreg(reg) \ ({ \ unsigned long res; \ - BUILD_BUG_ON(!__builtin_constant_p(reg)); \ if ((reg) == _IA64_REG_IP) \ res = ia64_native_getreg(_IA64_REG_IP); \ else \ -- cgit v1.1 From 6afc9be1de0b938169d8985a3add0e3727ebc717 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Mon, 1 Dec 2008 14:18:37 -0800 Subject: [IA64] eliminate NULL test and memset after alloc_bootmem As noted by Akinobu Mita in patch b1fceac2b9e04d278316b2faddf276015fc06e3b, alloc_bootmem and related functions never return NULL and always return a zeroed region of memory. Thus a NULL test or memset after calls to these functions is unnecessary. Signed-off-by: Julia Lawall Signed-off-by: Andrew Morton Signed-off-by: Tony Luck --- arch/ia64/sn/kernel/setup.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/ia64/sn/kernel/setup.c b/arch/ia64/sn/kernel/setup.c index bb1d249..b683eb3 100644 --- a/arch/ia64/sn/kernel/setup.c +++ b/arch/ia64/sn/kernel/setup.c @@ -512,7 +512,6 @@ static void __init sn_init_pdas(char **cmdline_p) for_each_online_node(cnode) { nodepdaindr[cnode] = alloc_bootmem_node(NODE_DATA(cnode), sizeof(nodepda_t)); - memset(nodepdaindr[cnode], 0, sizeof(nodepda_t)); memset(nodepdaindr[cnode]->phys_cpuid, -1, sizeof(nodepdaindr[cnode]->phys_cpuid)); spin_lock_init(&nodepdaindr[cnode]->ptc_lock); @@ -521,11 +520,9 @@ static void __init sn_init_pdas(char **cmdline_p) /* * Allocate & initialize nodepda for TIOs. For now, put them on node 0. */ - for (cnode = num_online_nodes(); cnode < num_cnodes; cnode++) { + for (cnode = num_online_nodes(); cnode < num_cnodes; cnode++) nodepdaindr[cnode] = alloc_bootmem_node(NODE_DATA(0), sizeof(nodepda_t)); - memset(nodepdaindr[cnode], 0, sizeof(nodepda_t)); - } /* * Now copy the array of nodepda pointers to each nodepda. -- cgit v1.1 From 9877e7b855dce9494a05f56f8ca6357f0b4b9169 Mon Sep 17 00:00:00 2001 From: Robin Holt Date: Mon, 8 Dec 2008 08:43:46 -0600 Subject: [IA64] Updated the generic_defconfig to work with the 2.6.28-rc7 kernel. The AUTOFS=y and AUTOFS4=y causes problems with some distros versions of automount. I turned both of those to =m and then followed the default prompts for everything else. I did notice that CONFIG_PNP_DEBUG got changed to CONFIG_PNP_DEBUG_MESSAGES and the default was a =y so I turned that back to a =n. Signed-off-by: Robin Holt Signed-off-by: Tony Luck --- arch/ia64/configs/generic_defconfig | 218 ++++++++++++++++++++++++------------ 1 file changed, 147 insertions(+), 71 deletions(-) (limited to 'arch') diff --git a/arch/ia64/configs/generic_defconfig b/arch/ia64/configs/generic_defconfig index e05f9e1..27eb676 100644 --- a/arch/ia64/configs/generic_defconfig +++ b/arch/ia64/configs/generic_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc1 -# Mon Aug 4 15:38:01 2008 +# Linux kernel version: 2.6.28-rc7 +# Mon Dec 8 08:12:07 2008 # CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" @@ -26,6 +26,7 @@ CONFIG_LOG_BUF_SHIFT=20 CONFIG_CGROUPS=y # CONFIG_CGROUP_DEBUG is not set # CONFIG_CGROUP_NS is not set +# CONFIG_CGROUP_FREEZER is not set # CONFIG_CGROUP_DEVICE is not set CONFIG_CPUSETS=y # CONFIG_GROUP_SCHED is not set @@ -46,7 +47,6 @@ CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_SYSCTL=y # CONFIG_EMBEDDED is not set CONFIG_SYSCTL_SYSCALL=y -CONFIG_SYSCTL_SYSCALL_CHECK=y CONFIG_KALLSYMS=y CONFIG_KALLSYMS_ALL=y # CONFIG_KALLSYMS_EXTRA_PASS is not set @@ -63,7 +63,9 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y +CONFIG_PCI_QUIRKS=y CONFIG_SLUB_DEBUG=y # CONFIG_SLAB is not set CONFIG_SLUB=y @@ -72,15 +74,11 @@ CONFIG_SLUB=y # CONFIG_MARKERS is not set CONFIG_HAVE_OPROFILE=y # CONFIG_KPROBES is not set -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set CONFIG_HAVE_KPROBES=y CONFIG_HAVE_KRETPROBES=y -# CONFIG_HAVE_ARCH_TRACEHOOK is not set +CONFIG_HAVE_ARCH_TRACEHOOK=y CONFIG_HAVE_DMA_ATTRS=y CONFIG_USE_GENERIC_SMP_HELPERS=y -# CONFIG_HAVE_CLK is not set -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -113,6 +111,7 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Processor type and features @@ -125,8 +124,6 @@ CONFIG_MMU=y CONFIG_SWIOTLB=y CONFIG_IOMMU_HELPER=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_CALIBRATE_DELAY=y @@ -139,13 +136,16 @@ CONFIG_GENERIC_IOMAP=y CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y CONFIG_IA64_UNCACHED_ALLOCATOR=y CONFIG_AUDIT_ARCH=y +# CONFIG_PARAVIRT_GUEST is not set CONFIG_IA64_GENERIC=y # CONFIG_IA64_DIG is not set +# CONFIG_IA64_DIG_VTD is not set # CONFIG_IA64_HP_ZX1 is not set # CONFIG_IA64_HP_ZX1_SWIOTLB is not set # CONFIG_IA64_SGI_SN2 is not set # CONFIG_IA64_SGI_UV is not set # CONFIG_IA64_HP_SIM is not set +# CONFIG_IA64_XEN_GUEST is not set # CONFIG_ITANIUM is not set CONFIG_MCKINLEY=y # CONFIG_IA64_PAGE_SIZE_4KB is not set @@ -182,16 +182,17 @@ CONFIG_DISCONTIGMEM_MANUAL=y CONFIG_DISCONTIGMEM=y CONFIG_FLAT_NODE_MEM_MAP=y CONFIG_NEED_MULTIPLE_NODES=y -# CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_MIGRATION=y CONFIG_RESOURCES_64BIT=y +CONFIG_PHYS_ADDR_T_64BIT=y CONFIG_ZONE_DMA_FLAG=1 CONFIG_BOUNCE=y CONFIG_NR_QUICK=1 CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y CONFIG_MMU_NOTIFIER=y CONFIG_ARCH_SELECT_MEMORY_MODEL=y CONFIG_ARCH_DISCONTIGMEM_ENABLE=y @@ -231,12 +232,12 @@ CONFIG_EFI_VARS=y CONFIG_EFI_PCDP=y CONFIG_DMIID=y CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=m -# CONFIG_DMAR is not set - # -# Power management and ACPI +# Power management and ACPI options # CONFIG_PM=y # CONFIG_PM_DEBUG is not set @@ -248,7 +249,6 @@ CONFIG_ACPI_PROC_EVENT=y CONFIG_ACPI_BUTTON=m CONFIG_ACPI_FAN=m CONFIG_ACPI_DOCK=y -# CONFIG_ACPI_BAY is not set CONFIG_ACPI_PROCESSOR=m CONFIG_ACPI_HOTPLUG_CPU=y CONFIG_ACPI_THERMAL=m @@ -256,9 +256,7 @@ CONFIG_ACPI_NUMA=y # CONFIG_ACPI_CUSTOM_DSDT is not set CONFIG_ACPI_BLACKLIST_YEAR=0 # CONFIG_ACPI_DEBUG is not set -CONFIG_ACPI_EC=y # CONFIG_ACPI_PCI_SLOT is not set -CONFIG_ACPI_POWER=y CONFIG_ACPI_SYSTEM=y CONFIG_ACPI_CONTAINER=m @@ -275,7 +273,7 @@ CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y -# CONFIG_PCI_MSI is not set +CONFIG_PCI_MSI=y CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set CONFIG_HOTPLUG_PCI=m @@ -286,6 +284,7 @@ CONFIG_HOTPLUG_PCI_ACPI=m # CONFIG_HOTPLUG_PCI_SHPC is not set # CONFIG_HOTPLUG_PCI_SGI is not set # CONFIG_PCCARD is not set +CONFIG_DMAR=y CONFIG_NET=y # @@ -333,6 +332,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -353,11 +353,10 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# +# CONFIG_PHONET is not set +CONFIG_WIRELESS=y # CONFIG_CFG80211 is not set +CONFIG_WIRELESS_OLD_REGULATORY=y # CONFIG_WIRELESS_EXT is not set # CONFIG_MAC80211 is not set # CONFIG_IEEE80211 is not set @@ -385,7 +384,7 @@ CONFIG_PROC_EVENTS=y # CONFIG_MTD is not set # CONFIG_PARPORT is not set CONFIG_PNP=y -# CONFIG_PNP_DEBUG is not set +# CONFIG_PNP_DEBUG_MESSAGES is not set # # Protocols @@ -419,10 +418,9 @@ CONFIG_SGI_XP=m # CONFIG_HP_ILO is not set CONFIG_SGI_GRU=m # CONFIG_SGI_GRU_DEBUG is not set +# CONFIG_C2PORT is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y -CONFIG_IDE_MAX_HWIFS=4 -CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide/ide.txt for help/info on IDE drives @@ -430,12 +428,12 @@ CONFIG_BLK_DEV_IDE=y CONFIG_IDE_TIMINGS=y CONFIG_IDE_ATAPI=y # CONFIG_BLK_DEV_IDE_SATA is not set -CONFIG_BLK_DEV_IDEDISK=y -# CONFIG_IDEDISK_MULTI_MODE is not set +CONFIG_IDE_GD=y +CONFIG_IDE_GD_ATA=y +# CONFIG_IDE_GD_ATAPI is not set CONFIG_BLK_DEV_IDECD=y CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y # CONFIG_BLK_DEV_IDETAPE is not set -CONFIG_BLK_DEV_IDEFLOPPY=y CONFIG_BLK_DEV_IDESCSI=m # CONFIG_BLK_DEV_IDEACPI is not set # CONFIG_IDE_TASK_IOCTL is not set @@ -705,6 +703,9 @@ CONFIG_TULIP=m # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set @@ -725,11 +726,11 @@ CONFIG_E100=m # CONFIG_TLAN is not set # CONFIG_VIA_RHINE is not set # CONFIG_SC92031 is not set +# CONFIG_ATL2 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set CONFIG_E1000=y -# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set # CONFIG_E1000E is not set # CONFIG_IP1000 is not set CONFIG_IGB=y @@ -747,18 +748,22 @@ CONFIG_TIGON3=y # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set +# CONFIG_JME is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_ENIC is not set # CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set # CONFIG_NIU is not set +# CONFIG_MLX4_EN is not set # CONFIG_MLX4_CORE is not set # CONFIG_TEHUTI is not set # CONFIG_BNX2X is not set +# CONFIG_QLGE is not set # CONFIG_SFC is not set # CONFIG_TR is not set @@ -826,9 +831,11 @@ CONFIG_MOUSE_PS2_LOGIPS2PP=y CONFIG_MOUSE_PS2_SYNAPTICS=y CONFIG_MOUSE_PS2_LIFEBOOK=y CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set # CONFIG_MOUSE_PS2_TOUCHKIT is not set # CONFIG_MOUSE_SERIAL is not set # CONFIG_MOUSE_APPLETOUCH is not set +# CONFIG_MOUSE_BCM5974 is not set # CONFIG_MOUSE_VSXXXAA is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TABLET is not set @@ -942,15 +949,16 @@ CONFIG_HWMON=y # CONFIG_SENSORS_VT8231 is not set # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set +# CONFIG_SENSORS_LIS3LV02D is not set # CONFIG_HWMON_DEBUG_CHIP is not set CONFIG_THERMAL=m # CONFIG_THERMAL_HWMON is not set # CONFIG_WATCHDOG is not set +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -959,6 +967,8 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -1009,6 +1019,7 @@ CONFIG_VGA_CONSOLE=y # CONFIG_VGACON_SOFT_SCROLLBACK is not set CONFIG_DUMMY_CONSOLE=y CONFIG_SOUND=m +CONFIG_SOUND_OSS_CORE=y CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m @@ -1113,8 +1124,7 @@ CONFIG_HID=y # USB Input Devices # CONFIG_USB_HID=m -# CONFIG_USB_HIDINPUT_POWERBOOK is not set -# CONFIG_HID_FF is not set +# CONFIG_HID_PID is not set # CONFIG_USB_HIDDEV is not set # @@ -1122,6 +1132,34 @@ CONFIG_USB_HID=m # # CONFIG_USB_KBD is not set # CONFIG_USB_MOUSE is not set + +# +# Special HID drivers +# +CONFIG_HID_COMPAT=y +CONFIG_HID_A4TECH=m +CONFIG_HID_APPLE=m +CONFIG_HID_BELKIN=m +CONFIG_HID_BRIGHT=m +CONFIG_HID_CHERRY=m +CONFIG_HID_CHICONY=m +CONFIG_HID_CYPRESS=m +CONFIG_HID_DELL=m +CONFIG_HID_EZKEY=m +CONFIG_HID_GYRATION=m +CONFIG_HID_LOGITECH=m +# CONFIG_LOGITECH_FF is not set +# CONFIG_LOGIRUMBLEPAD2_FF is not set +CONFIG_HID_MICROSOFT=m +CONFIG_HID_MONTEREY=m +CONFIG_HID_PANTHERLORD=m +# CONFIG_PANTHERLORD_FF is not set +CONFIG_HID_PETALYNX=m +CONFIG_HID_SAMSUNG=m +CONFIG_HID_SONY=m +CONFIG_HID_SUNPLUS=m +# CONFIG_THRUSTMASTER_FF is not set +# CONFIG_ZEROPLUS_FF is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -1138,6 +1176,9 @@ CONFIG_USB_DEVICE_CLASS=y # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_SUSPEND is not set # CONFIG_USB_OTG is not set +CONFIG_USB_MON=y +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set # # USB Host Controller Drivers @@ -1155,6 +1196,12 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y CONFIG_USB_UHCI_HCD=m # CONFIG_USB_SL811_HCD is not set # CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_WHCI_HCD is not set +# CONFIG_USB_HWA_HCD is not set + +# +# Enable Host or Gadget support to see Inventra options +# # # USB Device Class drivers @@ -1162,13 +1209,14 @@ CONFIG_USB_UHCI_HCD=m # CONFIG_USB_ACM is not set # CONFIG_USB_PRINTER is not set # CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set # -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; # # -# may also be needed; see USB_STORAGE Help for more information +# see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_DEBUG is not set @@ -1191,7 +1239,6 @@ CONFIG_USB_STORAGE=m # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set -CONFIG_USB_MON=y # # USB port drivers @@ -1204,7 +1251,7 @@ CONFIG_USB_MON=y # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_ADUTUX is not set -# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_SEVSEG is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set @@ -1222,7 +1269,9 @@ CONFIG_USB_MON=y # CONFIG_USB_IOWARRIOR is not set # CONFIG_USB_TEST is not set # CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set # CONFIG_USB_GADGET is not set +# CONFIG_UWB is not set # CONFIG_MMC is not set # CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set @@ -1246,6 +1295,15 @@ CONFIG_INFINIBAND_IPOIB_DEBUG=y # CONFIG_RTC_CLASS is not set # CONFIG_DMADEVICES is not set # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y + +# +# HP Simulator drivers +# +# CONFIG_HP_SIMETH is not set +# CONFIG_HP_SIMSERIAL is not set +# CONFIG_HP_SIMSCSI is not set CONFIG_MSPEC=m # @@ -1260,7 +1318,7 @@ CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y CONFIG_EXT3_FS_POSIX_ACL=y CONFIG_EXT3_FS_SECURITY=y -# CONFIG_EXT4DEV_FS is not set +# CONFIG_EXT4_FS is not set CONFIG_JBD=y CONFIG_FS_MBCACHE=y CONFIG_REISERFS_FS=y @@ -1271,6 +1329,7 @@ CONFIG_REISERFS_FS_POSIX_ACL=y CONFIG_REISERFS_FS_SECURITY=y # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y +CONFIG_FILE_LOCKING=y CONFIG_XFS_FS=y # CONFIG_XFS_QUOTA is not set # CONFIG_XFS_POSIX_ACL is not set @@ -1282,8 +1341,8 @@ CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y # CONFIG_QUOTA is not set -CONFIG_AUTOFS_FS=y -CONFIG_AUTOFS4_FS=y +CONFIG_AUTOFS_FS=m +CONFIG_AUTOFS4_FS=m # CONFIG_FUSE_FS is not set # @@ -1314,6 +1373,7 @@ CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_VMCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -1356,6 +1416,7 @@ CONFIG_NFS_COMMON=y CONFIG_SUNRPC=m CONFIG_SUNRPC_GSS=m CONFIG_SUNRPC_XPRT_RDMA=m +# CONFIG_SUNRPC_REGISTER_V4 is not set CONFIG_RPCSEC_GSS_KRB5=m # CONFIG_RPCSEC_GSS_SPKM3 is not set CONFIG_SMB_FS=m @@ -1433,38 +1494,6 @@ CONFIG_NLS_KOI8_R=m CONFIG_NLS_KOI8_U=m CONFIG_NLS_UTF8=m # CONFIG_DLM is not set -CONFIG_HAVE_KVM=y -CONFIG_VIRTUALIZATION=y -# CONFIG_KVM is not set - -# -# Library routines -# -CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_CRC_CCITT is not set -# CONFIG_CRC16 is not set -CONFIG_CRC_T10DIF=y -CONFIG_CRC_ITU_T=m -CONFIG_CRC32=y -# CONFIG_CRC7 is not set -# CONFIG_LIBCRC32C is not set -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_PLIST=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HAS_DMA=y -CONFIG_GENERIC_HARDIRQS=y -CONFIG_GENERIC_IRQ_PROBE=y -CONFIG_GENERIC_PENDING_IRQ=y -CONFIG_IRQ_PER_CPU=y - -# -# HP Simulator drivers -# -# CONFIG_HP_SIMETH is not set -# CONFIG_HP_SIMSERIAL is not set -# CONFIG_HP_SIMSCSI is not set # # Kernel hacking @@ -1503,8 +1532,19 @@ CONFIG_DEBUG_MEMORY_INIT=y # CONFIG_DEBUG_SG is not set # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set # CONFIG_FAULT_INJECTION is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set CONFIG_IA64_GRANULE_16MB=y # CONFIG_IA64_GRANULE_64MB is not set @@ -1519,14 +1559,19 @@ CONFIG_SYSVIPC_COMPAT=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=m CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_HASH=m +CONFIG_CRYPTO_RNG=m CONFIG_CRYPTO_MANAGER=m # CONFIG_CRYPTO_GF128MUL is not set # CONFIG_CRYPTO_NULL is not set @@ -1599,5 +1644,36 @@ CONFIG_CRYPTO_DES=m # # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set CONFIG_CRYPTO_HW=y # CONFIG_CRYPTO_DEV_HIFN_795X is not set +CONFIG_HAVE_KVM=y +CONFIG_VIRTUALIZATION=y +# CONFIG_KVM is not set +# CONFIG_VIRTIO_PCI is not set +# CONFIG_VIRTIO_BALLOON is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y +CONFIG_CRC_ITU_T=m +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_GENERIC_PENDING_IRQ=y +CONFIG_IRQ_PER_CPU=y -- cgit v1.1 From 6882edc04f37691ff9c7fcb30b52506cd7697eb0 Mon Sep 17 00:00:00 2001 From: Robin Holt Date: Mon, 8 Dec 2008 08:43:46 -0600 Subject: [IA64] Clear up section mismatch for sn_check_wars. The generic_defconfig has three section mismatches. This clears up sn_check_wars(). Signed-off-by: Robin Holt Signed-off-by: Jack Steiner Signed-off-by: Tony Luck --- arch/ia64/sn/kernel/setup.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/ia64/sn/kernel/setup.c b/arch/ia64/sn/kernel/setup.c index b683eb3..02c5b8a 100644 --- a/arch/ia64/sn/kernel/setup.c +++ b/arch/ia64/sn/kernel/setup.c @@ -200,7 +200,7 @@ static int __cpuinitdata shub_1_1_found; * Set flag for enabling shub specific wars */ -static inline int __init is_shub_1_1(int nasid) +static inline int __cpuinit is_shub_1_1(int nasid) { unsigned long id; int rev; @@ -212,7 +212,7 @@ static inline int __init is_shub_1_1(int nasid) return rev <= 2; } -static void __init sn_check_for_wars(void) +static void __cpuinit sn_check_for_wars(void) { int cnode; -- cgit v1.1 From 8704ad8552c5954b2cd9b3c76b4c50471049ad7f Mon Sep 17 00:00:00 2001 From: Robin Holt Date: Mon, 8 Dec 2008 08:43:46 -0600 Subject: [IA64] Clear up section mismatch with arch_unregister_cpu() The generic_defconfig has three section mismatches. This clears arch_unregister_cpu() Signed-off-by: Robin Holt Signed-off-by: Jack Steiner Signed-off-by: Tony Luck --- arch/ia64/kernel/topology.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/ia64/kernel/topology.c b/arch/ia64/kernel/topology.c index 26228e2..c75b914 100644 --- a/arch/ia64/kernel/topology.c +++ b/arch/ia64/kernel/topology.c @@ -53,10 +53,12 @@ int __ref arch_register_cpu(int num) } EXPORT_SYMBOL(arch_register_cpu); -void arch_unregister_cpu(int num) +void __ref arch_unregister_cpu(int num) { unregister_cpu(&sysfs_cpus[num].cpu); +#ifdef CONFIG_ACPI unmap_cpu_from_node(num, cpu_to_node(num)); +#endif } EXPORT_SYMBOL(arch_unregister_cpu); #else -- cgit v1.1 From ff740fb02146c83d96def1b897ed232b4e0fbcfd Mon Sep 17 00:00:00 2001 From: John Keller Date: Mon, 8 Dec 2008 11:44:11 -0600 Subject: [IA64] SN: prevent IRQ retargetting in request_irq() With the introduction of the generic affinity autoselector, irq_select_affinity(), IRQs are now being retargetted, using a default mask, via the request_irq() path. This results in all IRQs targetted at CPU 0. SN Altix assigns affinity in the SN PROM, and does not expect that to be changed as part of request_irq(). Set the IRQ_AFFINITY_SET flag to prevent request_irq() from resetting affinity. Signed-off-by: John Keller Signed-off-by: Tony Luck --- arch/ia64/sn/kernel/irq.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/ia64/sn/kernel/irq.c b/arch/ia64/sn/kernel/irq.c index 96c31b4..0c66dbd 100644 --- a/arch/ia64/sn/kernel/irq.c +++ b/arch/ia64/sn/kernel/irq.c @@ -5,7 +5,7 @@ * License. See the file "COPYING" in the main directory of this archive * for more details. * - * Copyright (c) 2000-2007 Silicon Graphics, Inc. All Rights Reserved. + * Copyright (c) 2000-2008 Silicon Graphics, Inc. All Rights Reserved. */ #include @@ -375,6 +375,7 @@ void sn_irq_fixup(struct pci_dev *pci_dev, struct sn_irq_info *sn_irq_info) int cpu = nasid_slice_to_cpuid(nasid, slice); #ifdef CONFIG_SMP int cpuphys; + irq_desc_t *desc; #endif pci_dev_get(pci_dev); @@ -391,6 +392,12 @@ void sn_irq_fixup(struct pci_dev *pci_dev, struct sn_irq_info *sn_irq_info) #ifdef CONFIG_SMP cpuphys = cpu_physical_id(cpu); set_irq_affinity_info(sn_irq_info->irq_irq, cpuphys, 0); + desc = irq_to_desc(sn_irq_info->irq_irq); + /* + * Affinity was set by the PROM, prevent it from + * being reset by the request_irq() path. + */ + desc->status |= IRQ_AFFINITY_SET; #endif } -- cgit v1.1 From 8a4830f8891be6b4e04809693a24771a4694e0b0 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Tue, 9 Dec 2008 11:56:20 -0800 Subject: sparseirq: fix !SMP && !PCI_MSI && !HT_IRQ build Ingo Molnar wrote: >>> drivers/pci/intr_remapping.c: In function 'irq_2_iommu_alloc': >>> drivers/pci/intr_remapping.c:72: error: 'boot_cpu_id' undeclared (first use in this function) >>> drivers/pci/intr_remapping.c:72: error: (Each undeclared identifier is reported only once >>> drivers/pci/intr_remapping.c:72: error: for each function it appears in.) sparseirq should only be used with SMP for now. --- arch/x86/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 48ac688..8943c13 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -240,7 +240,7 @@ config X86_HAS_BOOT_CPU_ID config SPARSE_IRQ bool "Support sparse irq numbering" - depends on PCI_MSI || HT_IRQ + depends on (PCI_MSI || HT_IRQ) && SMP default y help This enables support for sparse irq, esp for msi/msi-x. You may need -- cgit v1.1 From 98873f53becea9a8a46972ff252e96fe575b120d Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Tue, 9 Dec 2008 17:58:46 +0000 Subject: MIPS: Better than nothing implementation of PCI mmap to fix X. Certain X11 servers such as the SIS server will only work if PCI mmap is implemented. This patch implements PCI mmap but to be on the same side so close to a release it only supports uncached mappings so performance will not be optimal for some uses such as framebuffers. Thanks to Zhang Le for the original report and testing. Signed-off-by: Ralf Baechle --- arch/mips/include/asm/pci.h | 5 +++++ arch/mips/pci/pci.c | 24 ++++++++++++++++++++++++ 2 files changed, 29 insertions(+) (limited to 'arch') diff --git a/arch/mips/include/asm/pci.h b/arch/mips/include/asm/pci.h index 5510c53..053e463 100644 --- a/arch/mips/include/asm/pci.h +++ b/arch/mips/include/asm/pci.h @@ -79,6 +79,11 @@ static inline void pcibios_penalize_isa_irq(int irq, int active) /* We don't do dynamic PCI IRQ allocation */ } +#define HAVE_PCI_MMAP + +extern int pci_mmap_page_range(struct pci_dev *dev, struct vm_area_struct *vma, + enum pci_mmap_state mmap_state, int write_combine); + /* * Dynamic DMA mapping stuff. * MIPS has everything mapped statically. diff --git a/arch/mips/pci/pci.c b/arch/mips/pci/pci.c index a377e9d..62cae74 100644 --- a/arch/mips/pci/pci.c +++ b/arch/mips/pci/pci.c @@ -354,6 +354,30 @@ EXPORT_SYMBOL(PCIBIOS_MIN_IO); EXPORT_SYMBOL(PCIBIOS_MIN_MEM); #endif +int pci_mmap_page_range(struct pci_dev *dev, struct vm_area_struct *vma, + enum pci_mmap_state mmap_state, int write_combine) +{ + unsigned long prot; + + /* + * I/O space can be accessed via normal processor loads and stores on + * this platform but for now we elect not to do this and portable + * drivers should not do this anyway. + */ + if (mmap_state == pci_mmap_io) + return -EINVAL; + + /* + * Ignore write-combine; for now only return uncached mappings. + */ + prot = pgprot_val(vma->vm_page_prot); + prot = (prot & ~_CACHE_MASK) | _CACHE_UNCACHED; + vma->vm_page_prot = __pgprot(prot); + + return remap_pfn_range(vma, vma->vm_start, vma->vm_pgoff, + vma->vm_end - vma->vm_start, vma->vm_page_prot); +} + char * (*pcibios_plat_setup)(char *str) __devinitdata; char *__devinit pcibios_setup(char *str) -- cgit v1.1 From 361371201b60ffd686a694c848c1d5ad6061725f Mon Sep 17 00:00:00 2001 From: Balbir Singh Date: Tue, 9 Dec 2008 13:14:07 -0800 Subject: uml: boot broken due to buffer overrun mconsole_init() passed 256 bytes as length in os_create_unix_socket, while the sizeof UNIX_PATH_MAX is 108. This patch fixes that problem and avoids a big overrun bug reported on UML bootup. sockaddr_un.sun_path is UNIX_PATH_MAX long which causes the problem. Reported-by: Vikas K Managutte Reported-by: Sarvesh Kumar Lal Das Signed-off-by: Balbir Singh Reviewed-by: Pekka Enberg Reviewed-by: WANG Cong Cc: Jeff Dike Cc: [please check with Jeff] Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/um/drivers/mconsole_kern.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/um/drivers/mconsole_kern.c b/arch/um/drivers/mconsole_kern.c index 19d579d..8f44ebb 100644 --- a/arch/um/drivers/mconsole_kern.c +++ b/arch/um/drivers/mconsole_kern.c @@ -16,6 +16,8 @@ #include #include #include +#include +#include #include #include #include @@ -785,7 +787,7 @@ static int __init mconsole_init(void) /* long to avoid size mismatch warnings from gcc */ long sock; int err; - char file[256]; + char file[UNIX_PATH_MAX]; if (umid_file_name("mconsole", file, sizeof(file))) return -1; -- cgit v1.1 From cb32898c0996e78509a4b21b068209eb2d569f00 Mon Sep 17 00:00:00 2001 From: Cyrill Gorcunov Date: Wed, 10 Dec 2008 12:43:19 +0000 Subject: MN10300: vmlinux.lds.S cleanup - use PAGE_SIZE, PERCPU macros Include the linux/page.h header into the MN10300 kernel linker script thus allowing us to use PAGE_SIZE macro instead of a numeric constant. Also use the PERCPU macro instead of an explicit section definition. Signed-off-by: Cyrill Gorcunov Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- arch/mn10300/kernel/vmlinux.lds.S | 22 ++++++++++------------ 1 file changed, 10 insertions(+), 12 deletions(-) (limited to 'arch') diff --git a/arch/mn10300/kernel/vmlinux.lds.S b/arch/mn10300/kernel/vmlinux.lds.S index a3e80f4..b825966 100644 --- a/arch/mn10300/kernel/vmlinux.lds.S +++ b/arch/mn10300/kernel/vmlinux.lds.S @@ -11,6 +11,7 @@ #define __VMLINUX_LDS__ #include #include +#include OUTPUT_FORMAT("elf32-am33lin", "elf32-am33lin", "elf32-am33lin") OUTPUT_ARCH(mn10300) @@ -55,13 +56,13 @@ SECTIONS CONSTRUCTORS } - . = ALIGN(4096); + . = ALIGN(PAGE_SIZE); __nosave_begin = .; .data_nosave : { *(.data.nosave) } - . = ALIGN(4096); + . = ALIGN(PAGE_SIZE); __nosave_end = .; - . = ALIGN(4096); + . = ALIGN(PAGE_SIZE); .data.page_aligned : { *(.data.idt) } . = ALIGN(32); @@ -78,7 +79,7 @@ SECTIONS .data.init_task : { *(.data.init_task) } /* might get freed after init */ - . = ALIGN(4096); + . = ALIGN(PAGE_SIZE); .smp_locks : AT(ADDR(.smp_locks) - LOAD_OFFSET) { __smp_locks = .; *(.smp_locks) @@ -86,7 +87,7 @@ SECTIONS } /* will be freed after init */ - . = ALIGN(4096); /* Init code and data */ + . = ALIGN(PAGE_SIZE); /* Init code and data */ __init_begin = .; .init.text : { _sinittext = .; @@ -120,17 +121,14 @@ SECTIONS .exit.data : { *(.exit.data) } #ifdef CONFIG_BLK_DEV_INITRD - . = ALIGN(4096); + . = ALIGN(PAGE_SIZE); __initramfs_start = .; .init.ramfs : { *(.init.ramfs) } __initramfs_end = .; #endif - . = ALIGN(32); - __per_cpu_start = .; - .data.percpu : { *(.data.percpu) } - __per_cpu_end = .; - . = ALIGN(4096); + PERCPU(32) + . = ALIGN(PAGE_SIZE); __init_end = .; /* freed after init ends here */ @@ -145,7 +143,7 @@ SECTIONS _end = . ; /* This is where the kernel creates the early boot page tables */ - . = ALIGN(4096); + . = ALIGN(PAGE_SIZE); pg0 = .; /* Sections to be discarded */ -- cgit v1.1 From a8893fb3e61473349b052794ae157b938e3b2b98 Mon Sep 17 00:00:00 2001 From: Akira Takeuchi Date: Wed, 10 Dec 2008 12:43:24 +0000 Subject: MN10300: Discard low-priority Tx interrupts when closing an on-chip serial port Discard low-prioriy Tx interrupts when closing an MN10300 on-chip serial port. The MN10300 on-chip serial port uses three interrupts to manage its serial ports: (1) A very high priority interrupt that drives virtual DMA for Rx. (2) A very high priority interrupt that drives virtual DMA for Tx. (3) A normal priority virtual interrupt that does the normal UART interrupt stuff and is shared between Rx and Tx. mn10300_serial_stop_tx() only disables the high priority Tx interrupt. It doesn't also disable the normal priority one because it is shared with Rx. However, the high priority interrupt may interrupt local_irq_disabled() sections, and so may have queued up a low priority virtual interrupt whilst the UART driver is asking for the Tx interrupt to be disabled. The result of this can be an oops when we try to process the interrupt in mn10300_serial_transmit_interrupt() as port->uart.info and port->uart.info->tty may have gone away. To deal with this, if either of those pointers is NULL, we make sure the high-priority Tx interrupt is disabled and discard the interrupt. The low priority interrupt is disabled by the mn10300_serial_pic irq_chip table. Signed-off-by: Akira Takeuchi Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- arch/mn10300/kernel/mn10300-serial.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch') diff --git a/arch/mn10300/kernel/mn10300-serial.c b/arch/mn10300/kernel/mn10300-serial.c index aa07d0c..59b9c4b 100644 --- a/arch/mn10300/kernel/mn10300-serial.c +++ b/arch/mn10300/kernel/mn10300-serial.c @@ -566,6 +566,11 @@ static void mn10300_serial_transmit_interrupt(struct mn10300_serial_port *port) { _enter("%s", port->name); + if (!port->uart.info || !port->uart.info->port.tty) { + mn10300_serial_dis_tx_intr(port); + return; + } + if (uart_tx_stopped(&port->uart) || uart_circ_empty(&port->uart.info->xmit)) mn10300_serial_dis_tx_intr(port); -- cgit v1.1 From 24646bd2269fbca95367bfd3eafbc9f7ade2e980 Mon Sep 17 00:00:00 2001 From: Akira Takeuchi Date: Wed, 10 Dec 2008 12:43:29 +0000 Subject: MN10300: Fix the preemption resume_kernel() routine Fix the preemption resume_kernel() routine by inverting the test to see whether interrupts are off (IM7 is all enabled, not all disabled). Furthermore, interrupts should be disabled on entry to resume_kernel() so that they're correctly set for jumping to restore_all() and doing the need reschedule test. Signed-off-by: Akira Takeuchi Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- arch/mn10300/kernel/entry.S | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mn10300/kernel/entry.S b/arch/mn10300/kernel/entry.S index b7cbb14..62fba8a 100644 --- a/arch/mn10300/kernel/entry.S +++ b/arch/mn10300/kernel/entry.S @@ -180,6 +180,7 @@ ENTRY(resume_userspace) #ifdef CONFIG_PREEMPT ENTRY(resume_kernel) + __cli mov (TI_preempt_count,a2),d0 # non-zero preempt_count ? cmp 0,d0 bne restore_all @@ -190,7 +191,7 @@ need_resched: mov (REG_EPSW,fp),d0 and EPSW_IM,d0 cmp EPSW_IM_7,d0 # interrupts off (exception path) ? - beq restore_all + bne restore_all call preempt_schedule_irq[],0 jmp need_resched #endif -- cgit v1.1 From c7f8d6f6b5d121e5f7408119661ca29fc4661c10 Mon Sep 17 00:00:00 2001 From: Akira Takeuchi Date: Wed, 10 Dec 2008 12:43:39 +0000 Subject: MN10300: Give correct size when reserving interrupt vector table Give the correct size when reserving the interrupt vector table. It should be a page not a single byte. Signed-off-by: Akira Takeuchi Signed-off-by: David Howells Signed-off-by: Linus Torvalds --- arch/mn10300/kernel/setup.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mn10300/kernel/setup.c b/arch/mn10300/kernel/setup.c index 017121c..e1d88ab 100644 --- a/arch/mn10300/kernel/setup.c +++ b/arch/mn10300/kernel/setup.c @@ -161,7 +161,7 @@ void __init setup_arch(char **cmdline_p) reserve the page it is occupying. */ if (CONFIG_INTERRUPT_VECTOR_BASE >= CONFIG_KERNEL_RAM_BASE_ADDRESS && CONFIG_INTERRUPT_VECTOR_BASE < memory_end) - reserve_bootmem(CONFIG_INTERRUPT_VECTOR_BASE, 1, + reserve_bootmem(CONFIG_INTERRUPT_VECTOR_BASE, PAGE_SIZE, BOOTMEM_DEFAULT); reserve_bootmem(PAGE_ALIGN(PFN_PHYS(free_pfn)), bootmap_size, -- cgit v1.1 From bb49eed4221092fde4e2337534ae51d8f28a2fbe Mon Sep 17 00:00:00 2001 From: Alexander Beregalov Date: Wed, 10 Dec 2008 15:24:50 -0800 Subject: IA64: HP_SIMETH needs to depend upon NET From: Alexander Beregalov Signed-off-by: David S. Miller --- arch/ia64/hp/sim/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/ia64/hp/sim/Kconfig b/arch/ia64/hp/sim/Kconfig index f92306b..8d513a8 100644 --- a/arch/ia64/hp/sim/Kconfig +++ b/arch/ia64/hp/sim/Kconfig @@ -4,6 +4,7 @@ menu "HP Simulator drivers" config HP_SIMETH bool "Simulated Ethernet " + depends on NET config HP_SIMSERIAL bool "Simulated serial driver support" -- cgit v1.1 From 674a0a6939a954ab92fdd9833943e2277550bb0a Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Tue, 9 Dec 2008 03:13:39 +0100 Subject: [ARM] 5341/2: there is no copy_page on nommu ARM ... as it is defined with memcpy, therefore no copy_page symbol to export. Signed-off-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/kernel/armksyms.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/kernel/armksyms.c b/arch/arm/kernel/armksyms.c index c74f766..23af3c9 100644 --- a/arch/arm/kernel/armksyms.c +++ b/arch/arm/kernel/armksyms.c @@ -115,6 +115,8 @@ EXPORT_SYMBOL(__strnlen_user); EXPORT_SYMBOL(__strncpy_from_user); #ifdef CONFIG_MMU +EXPORT_SYMBOL(copy_page); + EXPORT_SYMBOL(__copy_from_user); EXPORT_SYMBOL(__copy_to_user); EXPORT_SYMBOL(__clear_user); @@ -181,8 +183,6 @@ EXPORT_SYMBOL(_find_first_bit_be); EXPORT_SYMBOL(_find_next_bit_be); #endif -EXPORT_SYMBOL(copy_page); - #ifdef CONFIG_FUNCTION_TRACER EXPORT_SYMBOL(mcount); #endif -- cgit v1.1 From 9f3eefc4f9b02404e89d624a6cd40e7b468b5fd5 Mon Sep 17 00:00:00 2001 From: Josh Boyer Date: Tue, 25 Nov 2008 06:33:35 +0000 Subject: powerpc/40x: Add proper BOOTCFLAGS for cuboot-acadia The cuboot-acadia.c wrapper can cause assembler errors on some toolchains due to the lack of the proper BOOTCFLAGS. This adds the proper flags for the file. Signed-off-by: Josh Boyer --- arch/powerpc/boot/Makefile | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/powerpc/boot/Makefile b/arch/powerpc/boot/Makefile index 8fc6d72..3d3daa6 100644 --- a/arch/powerpc/boot/Makefile +++ b/arch/powerpc/boot/Makefile @@ -41,6 +41,7 @@ $(obj)/4xx.o: BOOTCFLAGS += -mcpu=405 $(obj)/ebony.o: BOOTCFLAGS += -mcpu=405 $(obj)/cuboot-taishan.o: BOOTCFLAGS += -mcpu=405 $(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=405 +$(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405 $(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405 $(obj)/virtex405-head.o: BOOTAFLAGS += -mcpu=405 -- cgit v1.1 From b6354db5bbbc538bf009cae6c019810b4a3ef21d Mon Sep 17 00:00:00 2001 From: David Daney Date: Wed, 10 Dec 2008 08:37:25 -0800 Subject: MIPS: Use EI/DI for MIPS R2. For MIPS R2, use the EI and DI instructions to enable and disable interrupts. Signed-off-by: Tomaso Paoletti Signed-off-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/include/asm/asmmacro.h | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'arch') diff --git a/arch/mips/include/asm/asmmacro.h b/arch/mips/include/asm/asmmacro.h index 7a88175..6c8342a 100644 --- a/arch/mips/include/asm/asmmacro.h +++ b/arch/mips/include/asm/asmmacro.h @@ -35,6 +35,16 @@ mtc0 \reg, CP0_TCSTATUS _ehb .endm +#elif defined(CONFIG_CPU_MIPSR2) + .macro local_irq_enable reg=t0 + ei + irq_enable_hazard + .endm + + .macro local_irq_disable reg=t0 + di + irq_disable_hazard + .endm #else .macro local_irq_enable reg=t0 mfc0 \reg, CP0_STATUS -- cgit v1.1 From 00ace207164cb414efba406830256721f45c1c62 Mon Sep 17 00:00:00 2001 From: Dmitri Vorobiev Date: Wed, 10 Dec 2008 22:38:36 +0200 Subject: MIPS: Kconfig: Fix the arch-specific header path The header path in the help text for the RUNTIME_DEBUG config option is obsolete and needs to be updated to match the new location of architecture-specific header files. While at it, fix the spelling mistake. Signed-off-by: Dmitri Vorobiev Signed-off-by: Ralf Baechle --- arch/mips/Kconfig.debug | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/Kconfig.debug b/arch/mips/Kconfig.debug index 765c8e2..364ca89 100644 --- a/arch/mips/Kconfig.debug +++ b/arch/mips/Kconfig.debug @@ -48,7 +48,7 @@ config RUNTIME_DEBUG help If you say Y here, some debugging macros will do run-time checking. If you say N here, those macros will mostly turn to no-ops. See - include/asm-mips/debug.h for debuging macros. + arch/mips/include/asm/debug.h for debugging macros. If unsure, say N. endmenu -- cgit v1.1 From 11531ac2d3f24c3dc4df3861d72d1e8b9b8b6317 Mon Sep 17 00:00:00 2001 From: David Daney Date: Wed, 10 Dec 2008 18:14:45 -0800 Subject: MIPS: Add missing calls to plat_unmap_dma_mem. dma_free_noncoherent() and dma_free_coherent() are missing calls to plat_unmap_dma_mem(). This patch adds them. Signed-off-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/mm/dma-default.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/mips/mm/dma-default.c b/arch/mips/mm/dma-default.c index 5b98d0e..e6708b3 100644 --- a/arch/mips/mm/dma-default.c +++ b/arch/mips/mm/dma-default.c @@ -111,6 +111,7 @@ EXPORT_SYMBOL(dma_alloc_coherent); void dma_free_noncoherent(struct device *dev, size_t size, void *vaddr, dma_addr_t dma_handle) { + plat_unmap_dma_mem(dma_handle); free_pages((unsigned long) vaddr, get_order(size)); } @@ -121,6 +122,8 @@ void dma_free_coherent(struct device *dev, size_t size, void *vaddr, { unsigned long addr = (unsigned long) vaddr; + plat_unmap_dma_mem(dma_handle); + if (!plat_device_is_coherent(dev)) addr = CAC_ADDR(addr); -- cgit v1.1 From 6d8a52d7f09babf6cff1df32fe0b8ea47cf753f3 Mon Sep 17 00:00:00 2001 From: David Daney Date: Wed, 10 Dec 2008 15:27:13 -0800 Subject: MIPS: IP32: Update defconfig Signed-off-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/configs/ip32_defconfig | 1060 ++++++++++++++++++++++---------------- 1 file changed, 624 insertions(+), 436 deletions(-) (limited to 'arch') diff --git a/arch/mips/configs/ip32_defconfig b/arch/mips/configs/ip32_defconfig index fe4699d..de4c7a0 100644 --- a/arch/mips/configs/ip32_defconfig +++ b/arch/mips/configs/ip32_defconfig @@ -1,71 +1,71 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.20 -# Tue Feb 20 21:47:33 2007 +# Linux kernel version: 2.6.28-rc7 +# Wed Dec 10 14:39:08 2008 # CONFIG_MIPS=y # # Machine selection # -CONFIG_ZONE_DMA=y -# CONFIG_MIPS_MTX1 is not set -# CONFIG_MIPS_BOSPORUS is not set -# CONFIG_MIPS_PB1000 is not set -# CONFIG_MIPS_PB1100 is not set -# CONFIG_MIPS_PB1500 is not set -# CONFIG_MIPS_PB1550 is not set -# CONFIG_MIPS_PB1200 is not set -# CONFIG_MIPS_DB1000 is not set -# CONFIG_MIPS_DB1100 is not set -# CONFIG_MIPS_DB1500 is not set -# CONFIG_MIPS_DB1550 is not set -# CONFIG_MIPS_DB1200 is not set -# CONFIG_MIPS_MIRAGE is not set +# CONFIG_MACH_ALCHEMY is not set # CONFIG_BASLER_EXCITE is not set +# CONFIG_BCM47XX is not set # CONFIG_MIPS_COBALT is not set # CONFIG_MACH_DECSTATION is not set # CONFIG_MACH_JAZZ is not set +# CONFIG_LASAT is not set +# CONFIG_LEMOTE_FULONG is not set # CONFIG_MIPS_MALTA is not set -# CONFIG_WR_PPMC is not set # CONFIG_MIPS_SIM is not set -# CONFIG_MOMENCO_JAGUAR_ATX is not set -# CONFIG_MIPS_XXS1500 is not set +# CONFIG_MACH_EMMA is not set +# CONFIG_MACH_VR41XX is not set +# CONFIG_NXP_STB220 is not set +# CONFIG_NXP_STB225 is not set # CONFIG_PNX8550_JBS is not set # CONFIG_PNX8550_STB810 is not set -# CONFIG_MACH_VR41XX is not set +# CONFIG_PMC_MSP is not set # CONFIG_PMC_YOSEMITE is not set -# CONFIG_MARKEINS is not set # CONFIG_SGI_IP22 is not set # CONFIG_SGI_IP27 is not set +# CONFIG_SGI_IP28 is not set CONFIG_SGI_IP32=y -# CONFIG_SIBYTE_BIGSUR is not set -# CONFIG_SIBYTE_SWARM is not set -# CONFIG_SIBYTE_SENTOSA is not set -# CONFIG_SIBYTE_RHONE is not set -# CONFIG_SIBYTE_CARMEL is not set -# CONFIG_SIBYTE_LITTLESUR is not set # CONFIG_SIBYTE_CRHINE is not set +# CONFIG_SIBYTE_CARMEL is not set # CONFIG_SIBYTE_CRHONE is not set +# CONFIG_SIBYTE_RHONE is not set +# CONFIG_SIBYTE_SWARM is not set +# CONFIG_SIBYTE_LITTLESUR is not set +# CONFIG_SIBYTE_SENTOSA is not set +# CONFIG_SIBYTE_BIGSUR is not set # CONFIG_SNI_RM is not set -# CONFIG_TOSHIBA_JMR3927 is not set -# CONFIG_TOSHIBA_RBTX4927 is not set -# CONFIG_TOSHIBA_RBTX4938 is not set +# CONFIG_MACH_TX39XX is not set +# CONFIG_MACH_TX49XX is not set +# CONFIG_MIKROTIK_RB532 is not set +# CONFIG_WR_PPMC is not set CONFIG_RWSEM_GENERIC_SPINLOCK=y # CONFIG_ARCH_HAS_ILOG2_U32 is not set # CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_ARCH_SUPPORTS_OPROFILE=y CONFIG_GENERIC_FIND_NEXT_BIT=y CONFIG_GENERIC_HWEIGHT=y CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CMOS_UPDATE=y CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y # CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set CONFIG_ARC=y +CONFIG_CEVT_R4K=y +CONFIG_CSRC_R4K=y CONFIG_DMA_NONCOHERENT=y CONFIG_DMA_NEED_PCI_MAP_STATE=y +# CONFIG_HOTPLUG_CPU is not set +# CONFIG_NO_IOPORT is not set CONFIG_CPU_BIG_ENDIAN=y # CONFIG_CPU_LITTLE_ENDIAN is not set CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_IRQ_CPU=y CONFIG_ARC32=y CONFIG_BOOT_ELF32=y CONFIG_MIPS_L1_CACHE_SHIFT=5 @@ -75,6 +75,7 @@ CONFIG_ARC_PROMLIB=y # # CPU selection # +# CONFIG_CPU_LOONGSON2 is not set # CONFIG_CPU_MIPS32_R1 is not set # CONFIG_CPU_MIPS32_R2 is not set # CONFIG_CPU_MIPS64_R1 is not set @@ -87,6 +88,7 @@ CONFIG_ARC_PROMLIB=y # CONFIG_CPU_TX49XX is not set CONFIG_CPU_R5000=y # CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R5500 is not set # CONFIG_CPU_R6000 is not set # CONFIG_CPU_NEVADA is not set # CONFIG_CPU_R8000 is not set @@ -116,65 +118,73 @@ CONFIG_RM7000_CPU_SCACHE=y CONFIG_MIPS_MT_DISABLED=y # CONFIG_MIPS_MT_SMP is not set # CONFIG_MIPS_MT_SMTC is not set -# CONFIG_MIPS_VPE_LOADER is not set CONFIG_CPU_HAS_LLSC=y CONFIG_CPU_HAS_SYNC=y CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_ARCH_FLATMEM_ENABLE=y +CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y -CONFIG_ZONE_DMA_FLAG=1 +CONFIG_PHYS_ADDR_T_64BIT=y +CONFIG_ZONE_DMA_FLAG=0 +CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_48 is not set # CONFIG_HZ_100 is not set # CONFIG_HZ_128 is not set -# CONFIG_HZ_250 is not set +CONFIG_HZ_250=y # CONFIG_HZ_256 is not set -CONFIG_HZ_1000=y +# CONFIG_HZ_1000 is not set # CONFIG_HZ_1024 is not set CONFIG_SYS_SUPPORTS_ARBIT_HZ=y -CONFIG_HZ=1000 -# CONFIG_PREEMPT_NONE is not set -CONFIG_PREEMPT_VOLUNTARY=y +CONFIG_HZ=250 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set # CONFIG_PREEMPT is not set # CONFIG_KEXEC is not set +# CONFIG_SECCOMP is not set CONFIG_LOCKDEP_SUPPORT=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" # -# Code maturity level options +# General setup # CONFIG_EXPERIMENTAL=y CONFIG_BROKEN_ON_SMP=y CONFIG_INIT_ENV_ARG_LIMIT=32 - -# -# General setup -# CONFIG_LOCALVERSION="" CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y -# CONFIG_IPC_NS is not set CONFIG_SYSVIPC_SYSCTL=y -# CONFIG_POSIX_MQUEUE is not set +CONFIG_POSIX_MQUEUE=y CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set # CONFIG_TASKSTATS is not set -# CONFIG_UTS_NS is not set -# CONFIG_AUDIT is not set -# CONFIG_IKCONFIG is not set +CONFIG_AUDIT=y +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y CONFIG_RELAY=y -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +# CONFIG_NAMESPACES is not set +# CONFIG_BLK_DEV_INITRD is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y CONFIG_SYSCTL=y CONFIG_EMBEDDED=y CONFIG_SYSCTL_SYSCALL=y @@ -184,27 +194,43 @@ CONFIG_HOTPLUG=y CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_ELF_CORE=y +CONFIG_PCSPKR_PLATFORM=y +CONFIG_COMPAT_BRK=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y +CONFIG_ANON_INODES=y CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y CONFIG_SHMEM=y -CONFIG_SLAB=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y +CONFIG_PCI_QUIRKS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_PROFILING=y +# CONFIG_MARKERS is not set +CONFIG_OPROFILE=m +CONFIG_HAVE_OPROFILE=y +# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set +CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 -# CONFIG_SLOB is not set - -# -# Loadable module support -# -# CONFIG_MODULES is not set - -# -# Block layer -# +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set +CONFIG_BLOCK_COMPAT=y # # IO Schedulers @@ -213,59 +239,50 @@ CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y CONFIG_IOSCHED_CFQ=y -CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_AS is not set # CONFIG_DEFAULT_DEADLINE is not set -# CONFIG_DEFAULT_CFQ is not set +CONFIG_DEFAULT_CFQ=y # CONFIG_DEFAULT_NOOP is not set -CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_DEFAULT_IOSCHED="cfq" +CONFIG_CLASSIC_RCU=y +# CONFIG_FREEZER is not set # # Bus options (PCI, PCMCIA, EISA, ISA, TC) # CONFIG_HW_HAS_PCI=y CONFIG_PCI=y +CONFIG_PCI_DOMAINS=y +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCI_LEGACY is not set CONFIG_MMU=y - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set - -# -# PCI Hotplug Support -# # CONFIG_HOTPLUG_PCI is not set # # Executable file formats # CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +# CONFIG_HAVE_AOUT is not set CONFIG_BINFMT_MISC=y -# CONFIG_BUILD_ELF64 is not set CONFIG_MIPS32_COMPAT=y CONFIG_COMPAT=y CONFIG_SYSVIPC_COMPAT=y CONFIG_MIPS32_O32=y -# CONFIG_MIPS32_N32 is not set +CONFIG_MIPS32_N32=y CONFIG_BINFMT_ELF32=y # # Power management options # -CONFIG_PM=y -# CONFIG_PM_LEGACY is not set -# CONFIG_PM_DEBUG is not set -# CONFIG_PM_SYSFS_DEPRECATED is not set - -# -# Networking -# +CONFIG_ARCH_SUSPEND_POSSIBLE=y +# CONFIG_PM is not set CONFIG_NET=y # # Networking options # -# CONFIG_NETDEBUG is not set CONFIG_PACKET=y CONFIG_PACKET_MMAP=y CONFIG_UNIX=y @@ -273,56 +290,83 @@ CONFIG_XFRM=y CONFIG_XFRM_USER=y # CONFIG_XFRM_SUB_POLICY is not set CONFIG_XFRM_MIGRATE=y +# CONFIG_XFRM_STATISTICS is not set +CONFIG_XFRM_IPCOMP=m CONFIG_NET_KEY=y CONFIG_NET_KEY_MIGRATE=y CONFIG_INET=y -# CONFIG_IP_MULTICAST is not set +CONFIG_IP_MULTICAST=y # CONFIG_IP_ADVANCED_ROUTER is not set CONFIG_IP_FIB_HASH=y CONFIG_IP_PNP=y -# CONFIG_IP_PNP_DHCP is not set +CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y # CONFIG_IP_PNP_RARP is not set -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set +CONFIG_NET_IPIP=m +CONFIG_NET_IPGRE=m +# CONFIG_NET_IPGRE_BROADCAST is not set +# CONFIG_IP_MROUTE is not set # CONFIG_ARPD is not set # CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_XFRM_TUNNEL is not set -# CONFIG_INET_TUNNEL is not set +CONFIG_INET_AH=m +CONFIG_INET_ESP=m +CONFIG_INET_IPCOMP=m +CONFIG_INET_XFRM_TUNNEL=m +CONFIG_INET_TUNNEL=m CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y -# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_ADVANCED=y +CONFIG_TCP_CONG_BIC=m CONFIG_TCP_CONG_CUBIC=y +CONFIG_TCP_CONG_WESTWOOD=m +CONFIG_TCP_CONG_HTCP=m +# CONFIG_TCP_CONG_HSTCP is not set +# CONFIG_TCP_CONG_HYBLA is not set +# CONFIG_TCP_CONG_VEGAS is not set +# CONFIG_TCP_CONG_SCALABLE is not set +# CONFIG_TCP_CONG_LP is not set +# CONFIG_TCP_CONG_VENO is not set +# CONFIG_TCP_CONG_YEAH is not set +# CONFIG_TCP_CONG_ILLINOIS is not set +# CONFIG_DEFAULT_BIC is not set +CONFIG_DEFAULT_CUBIC=y +# CONFIG_DEFAULT_HTCP is not set +# CONFIG_DEFAULT_VEGAS is not set +# CONFIG_DEFAULT_WESTWOOD is not set +# CONFIG_DEFAULT_RENO is not set CONFIG_DEFAULT_TCP_CONG="cubic" CONFIG_TCP_MD5SIG=y -# CONFIG_IPV6 is not set -# CONFIG_INET6_XFRM_TUNNEL is not set -# CONFIG_INET6_TUNNEL is not set +CONFIG_IPV6=m +# CONFIG_IPV6_PRIVACY is not set +# CONFIG_IPV6_ROUTER_PREF is not set +# CONFIG_IPV6_OPTIMISTIC_DAD is not set +CONFIG_INET6_AH=m +CONFIG_INET6_ESP=m +CONFIG_INET6_IPCOMP=m +# CONFIG_IPV6_MIP6 is not set +CONFIG_INET6_XFRM_TUNNEL=m +CONFIG_INET6_TUNNEL=m +CONFIG_INET6_XFRM_MODE_TRANSPORT=m +CONFIG_INET6_XFRM_MODE_TUNNEL=m +CONFIG_INET6_XFRM_MODE_BEET=m +# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set +CONFIG_IPV6_SIT=m +CONFIG_IPV6_NDISC_NODETYPE=y +CONFIG_IPV6_TUNNEL=m +# CONFIG_IPV6_MULTIPLE_TABLES is not set +# CONFIG_IPV6_MROUTE is not set CONFIG_NETWORK_SECMARK=y # CONFIG_NETFILTER is not set - -# -# DCCP Configuration (EXPERIMENTAL) -# # CONFIG_IP_DCCP is not set - -# -# SCTP Configuration (EXPERIMENTAL) -# # CONFIG_IP_SCTP is not set - -# -# TIPC Configuration (EXPERIMENTAL) -# # CONFIG_TIPC is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set @@ -332,10 +376,6 @@ CONFIG_NETWORK_SECMARK=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -343,15 +383,14 @@ CONFIG_NETWORK_SECMARK=y # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set # CONFIG_IRDA is not set # CONFIG_BT is not set -CONFIG_IEEE80211=y -# CONFIG_IEEE80211_DEBUG is not set -CONFIG_IEEE80211_CRYPT_WEP=y -CONFIG_IEEE80211_CRYPT_CCMP=y -CONFIG_IEEE80211_SOFTMAC=y -# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set -CONFIG_WIRELESS_EXT=y +# CONFIG_AF_RXRPC is not set +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set # # Device Drivers @@ -360,60 +399,40 @@ CONFIG_WIRELESS_EXT=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" # CONFIG_SYS_HYPERVISOR is not set - -# -# Connector - unified userspace <-> kernelspace linker -# CONFIG_CONNECTOR=y CONFIG_PROC_EVENTS=y - -# -# Memory Technology Devices (MTD) -# # CONFIG_MTD is not set - -# -# Parallel port support -# # CONFIG_PARPORT is not set - -# -# Plug and Play support -# -# CONFIG_PNPACPI is not set - -# -# Block devices -# +CONFIG_BLK_DEV=y # CONFIG_BLK_CPQ_DA is not set # CONFIG_BLK_CPQ_CISS_DA is not set # CONFIG_BLK_DEV_DAC960 is not set # CONFIG_BLK_DEV_UMEM is not set # CONFIG_BLK_DEV_COW_COMMON is not set -CONFIG_BLK_DEV_LOOP=y -# CONFIG_BLK_DEV_CRYPTOLOOP is not set -# CONFIG_BLK_DEV_NBD is not set +CONFIG_BLK_DEV_LOOP=m +CONFIG_BLK_DEV_CRYPTOLOOP=m +CONFIG_BLK_DEV_NBD=m # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_RAM is not set -# CONFIG_BLK_DEV_INITRD is not set -CONFIG_CDROM_PKTCDVD=y -CONFIG_CDROM_PKTCDVD_BUFFERS=8 -# CONFIG_CDROM_PKTCDVD_WCACHE is not set -CONFIG_ATA_OVER_ETH=y - -# -# Misc devices -# +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_BLK_DEV_HD is not set +CONFIG_MISC_DEVICES=y +# CONFIG_PHANTOM is not set +# CONFIG_EEPROM_93CX6 is not set CONFIG_SGI_IOC4=y # CONFIG_TIFM_CORE is not set - -# -# ATA/ATAPI/MFM/RLL support -# +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_HP_ILO is not set +# CONFIG_C2PORT is not set +CONFIG_HAVE_IDE=y # CONFIG_IDE is not set # @@ -421,19 +440,20 @@ CONFIG_SGI_IOC4=y # CONFIG_RAID_ATTRS=y CONFIG_SCSI=y +CONFIG_SCSI_DMA=y CONFIG_SCSI_TGT=y -CONFIG_SCSI_NETLINK=y +# CONFIG_SCSI_NETLINK is not set CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=y -CONFIG_CHR_DEV_ST=y -CONFIG_CHR_DEV_OSST=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set CONFIG_BLK_DEV_SR=y CONFIG_BLK_DEV_SR_VENDOR=y -CONFIG_CHR_DEV_SG=y +CONFIG_CHR_DEV_SG=m # CONFIG_CHR_DEV_SCH is not set # @@ -443,35 +463,36 @@ CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y CONFIG_SCSI_SCAN_ASYNC=y +CONFIG_SCSI_WAIT_SCAN=m # # SCSI Transports # CONFIG_SCSI_SPI_ATTRS=y -CONFIG_SCSI_FC_ATTRS=y +# CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set CONFIG_SCSI_SAS_ATTRS=y CONFIG_SCSI_SAS_LIBSAS=y +CONFIG_SCSI_SAS_HOST_SMP=y # CONFIG_SCSI_SAS_LIBSAS_DEBUG is not set - -# -# SCSI low-level drivers -# +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set # CONFIG_SCSI_AACRAID is not set CONFIG_SCSI_AIC7XXX=y -CONFIG_AIC7XXX_CMDS_PER_DEVICE=8 +CONFIG_AIC7XXX_CMDS_PER_DEVICE=32 CONFIG_AIC7XXX_RESET_DELAY_MS=15000 CONFIG_AIC7XXX_DEBUG_ENABLE=y CONFIG_AIC7XXX_DEBUG_MASK=0 CONFIG_AIC7XXX_REG_PRETTY_PRINT=y # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set -CONFIG_SCSI_AIC94XX=y -# CONFIG_AIC94XX_DEBUG is not set +# CONFIG_SCSI_AIC94XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -482,6 +503,7 @@ CONFIG_SCSI_AIC94XX=y # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_MVSAS is not set # CONFIG_SCSI_STEX is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_QLOGIC_1280 is not set @@ -492,147 +514,81 @@ CONFIG_SCSI_AIC94XX=y # CONFIG_SCSI_DC390T is not set # CONFIG_SCSI_DEBUG is not set # CONFIG_SCSI_SRP is not set - -# -# Serial ATA (prod) and Parallel ATA (experimental) drivers -# +# CONFIG_SCSI_DH is not set # CONFIG_ATA is not set - -# -# Multi-device support (RAID and LVM) -# # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support # -# CONFIG_IEEE1394 is not set # -# I2O device support +# Enable only one of the two stacks, unless you know what you are doing # +# CONFIG_FIREWIRE is not set +# CONFIG_IEEE1394 is not set # CONFIG_I2O is not set - -# -# Network device support -# CONFIG_NETDEVICES=y -# CONFIG_DUMMY is not set -# CONFIG_BONDING is not set +CONFIG_DUMMY=m +CONFIG_BONDING=m +# CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set - -# -# ARCnet devices -# +# CONFIG_VETH is not set # CONFIG_ARCNET is not set - -# -# PHY device support -# -CONFIG_PHYLIB=y - -# -# MII PHY device drivers -# -CONFIG_MARVELL_PHY=y -CONFIG_DAVICOM_PHY=y -CONFIG_QSEMI_PHY=y -CONFIG_LXT_PHY=y -CONFIG_CICADA_PHY=y -CONFIG_VITESSE_PHY=y -CONFIG_SMSC_PHY=y -# CONFIG_BROADCOM_PHY is not set -# CONFIG_FIXED_PHY is not set - -# -# Ethernet (10 or 100Mbit) -# +# CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y -# CONFIG_MII is not set +CONFIG_MII=y +# CONFIG_AX88796 is not set CONFIG_SGI_O2MACE_ETH=y # CONFIG_HAPPYMEAL is not set # CONFIG_SUNGEM is not set # CONFIG_CASSINI is not set # CONFIG_NET_VENDOR_3COM is not set +# CONFIG_SMC91X is not set # CONFIG_DM9000 is not set - -# -# Tulip family network device support -# -# CONFIG_NET_TULIP is not set +CONFIG_NET_TULIP=y +CONFIG_DE2104X=m +CONFIG_TULIP=m +# CONFIG_TULIP_MWI is not set +CONFIG_TULIP_MMIO=y +# CONFIG_TULIP_NAPI is not set +# CONFIG_DE4X5 is not set +# CONFIG_WINBOND_840 is not set +# CONFIG_DM9102 is not set +# CONFIG_ULI526X is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_NET_PCI is not set - -# -# Ethernet (1000 Mbit) -# -# CONFIG_ACENIC is not set -# CONFIG_DL2K is not set -# CONFIG_E1000 is not set -# CONFIG_NS83820 is not set -# CONFIG_HAMACHI is not set -# CONFIG_YELLOWFIN is not set -# CONFIG_R8169 is not set -# CONFIG_SIS190 is not set -# CONFIG_SKGE is not set -# CONFIG_SKY2 is not set -# CONFIG_SK98LIN is not set -# CONFIG_TIGON3 is not set -# CONFIG_BNX2 is not set -CONFIG_QLA3XXX=y -# CONFIG_ATL1 is not set - -# -# Ethernet (10000 Mbit) -# -# CONFIG_CHELSIO_T1 is not set -CONFIG_CHELSIO_T3=y -# CONFIG_IXGB is not set -# CONFIG_S2IO is not set -# CONFIG_MYRI10GE is not set -CONFIG_NETXEN_NIC=y - -# -# Token Ring devices -# +# CONFIG_B44 is not set +# CONFIG_ATL2 is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set # CONFIG_TR is not set # -# Wireless LAN (non-hamradio) -# -# CONFIG_NET_RADIO is not set - -# -# Wan interfaces +# Wireless LAN # +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NET_FC is not set -# CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set - -# -# ISDN subsystem -# # CONFIG_ISDN is not set - -# -# Telephony Support -# # CONFIG_PHONE is not set # @@ -640,6 +596,7 @@ CONFIG_NETXEN_NIC=y # CONFIG_INPUT=y # CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set # # Userland interfaces @@ -649,16 +606,32 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set -# CONFIG_INPUT_EVDEV is not set +CONFIG_INPUT_EVDEV=m # CONFIG_INPUT_EVBUG is not set # # Input Device Drivers # -# CONFIG_INPUT_KEYBOARD is not set -# CONFIG_INPUT_MOUSE is not set +CONFIG_INPUT_KEYBOARD=y +CONFIG_KEYBOARD_ATKBD=y +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +# CONFIG_KEYBOARD_STOWAWAY is not set +CONFIG_INPUT_MOUSE=y +CONFIG_MOUSE_PS2=y +CONFIG_MOUSE_PS2_ALPS=y +CONFIG_MOUSE_PS2_LOGIPS2PP=y +CONFIG_MOUSE_PS2_SYNAPTICS=y +CONFIG_MOUSE_PS2_LIFEBOOK=y +CONFIG_MOUSE_PS2_TRACKPOINT=y +# CONFIG_MOUSE_PS2_ELANTECH is not set +# CONFIG_MOUSE_PS2_TOUCHKIT is not set +# CONFIG_MOUSE_SERIAL is not set +# CONFIG_MOUSE_VSXXXAA is not set # CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set # CONFIG_INPUT_TOUCHSCREEN is not set # CONFIG_INPUT_MISC is not set @@ -669,8 +642,8 @@ CONFIG_SERIO=y # CONFIG_SERIO_I8042 is not set CONFIG_SERIO_SERPORT=y # CONFIG_SERIO_PCIPS2 is not set -# CONFIG_SERIO_MACEPS2 is not set -# CONFIG_SERIO_LIBPS2 is not set +CONFIG_SERIO_MACEPS2=y +CONFIG_SERIO_LIBPS2=y CONFIG_SERIO_RAW=y # CONFIG_GAMEPORT is not set @@ -678,10 +651,13 @@ CONFIG_SERIO_RAW=y # Character devices # CONFIG_VT=y +# CONFIG_CONSOLE_TRANSLATIONS is not set CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y -CONFIG_VT_HW_CONSOLE_BINDING=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y # CONFIG_SERIAL_NONSTANDARD is not set +# CONFIG_NOZOMI is not set # # Serial drivers @@ -702,192 +678,304 @@ CONFIG_SERIAL_CORE_CONSOLE=y CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 - -# -# IPMI -# # CONFIG_IPMI_HANDLER is not set - -# -# Watchdog Cards -# -# CONFIG_WATCHDOG is not set -# CONFIG_HW_RANDOM is not set -# CONFIG_RTC is not set -# CONFIG_GEN_RTC is not set -# CONFIG_DTLK is not set +CONFIG_HW_RANDOM=y # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set - -# -# TPM devices -# # CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +# CONFIG_I2C is not set +# CONFIG_SPI is not set +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_I5K_AMB is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_SIS5595 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_VIA686A is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_SENSORS_VT8231 is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_THERMAL is not set +# CONFIG_THERMAL_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set # -# I2C support +# Watchdog Device Drivers # -# CONFIG_I2C is not set +# CONFIG_SOFT_WATCHDOG is not set +# CONFIG_ALIM7101_WDT is not set # -# SPI support +# PCI-based Watchdog Cards # -# CONFIG_SPI is not set -# CONFIG_SPI_MASTER is not set +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set +CONFIG_SSB_POSSIBLE=y # -# Dallas's 1-wire bus +# Sonics Silicon Backplane # -# CONFIG_W1 is not set +# CONFIG_SSB is not set # -# Hardware Monitoring support +# Multifunction device drivers # -# CONFIG_HWMON is not set -# CONFIG_HWMON_VID is not set +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_REGULATOR is not set # # Multimedia devices # -# CONFIG_VIDEO_DEV is not set # -# Digital Video Broadcasting Devices +# Multimedia core support # -# CONFIG_DVB is not set +CONFIG_VIDEO_DEV=m +CONFIG_VIDEO_V4L2_COMMON=m +CONFIG_VIDEO_ALLOW_V4L1=y +CONFIG_VIDEO_V4L1_COMPAT=y +# CONFIG_DVB_CORE is not set +CONFIG_VIDEO_MEDIA=m # -# Graphics support +# Multimedia drivers # -# CONFIG_FIRMWARE_EDID is not set -# CONFIG_FB is not set +# CONFIG_MEDIA_ATTACH is not set +CONFIG_VIDEO_V4L2=m +CONFIG_VIDEO_V4L1=m +CONFIG_VIDEOBUF_GEN=m +CONFIG_VIDEOBUF_VMALLOC=m +CONFIG_VIDEO_CAPTURE_DRIVERS=y +# CONFIG_VIDEO_ADV_DEBUG is not set +# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set +CONFIG_VIDEO_HELPER_CHIPS_AUTO=y +CONFIG_VIDEO_VIVI=m +# CONFIG_VIDEO_CPIA is not set +# CONFIG_VIDEO_STRADIS is not set +# CONFIG_SOC_CAMERA is not set +CONFIG_RADIO_ADAPTERS=y +# CONFIG_RADIO_GEMTEK_PCI is not set +# CONFIG_RADIO_MAXIRADIO is not set +# CONFIG_RADIO_MAESTRO is not set +CONFIG_DAB=y # -# Console display driver support +# Graphics support # -# CONFIG_VGA_CONSOLE is not set -CONFIG_DUMMY_CONSOLE=y +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +CONFIG_FB=y +CONFIG_FIRMWARE_EDID=y +# CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_CIRRUS is not set +# CONFIG_FB_PM2 is not set +# CONFIG_FB_CYBER2000 is not set +# CONFIG_FB_ASILIANT is not set +# CONFIG_FB_IMSTT is not set +# CONFIG_FB_UVESA is not set +CONFIG_FB_GBE=y +CONFIG_FB_GBE_MEM=4 +# CONFIG_FB_S1D13XXX is not set +# CONFIG_FB_NVIDIA is not set +# CONFIG_FB_RIVA is not set +# CONFIG_FB_MATROX is not set +# CONFIG_FB_RADEON is not set +# CONFIG_FB_ATY128 is not set +# CONFIG_FB_ATY is not set +# CONFIG_FB_S3 is not set +# CONFIG_FB_SAVAGE is not set +# CONFIG_FB_SIS is not set +# CONFIG_FB_VIA is not set +# CONFIG_FB_NEOMAGIC is not set +# CONFIG_FB_KYRO is not set +# CONFIG_FB_3DFX is not set +# CONFIG_FB_VOODOO1 is not set +# CONFIG_FB_VT8623 is not set +# CONFIG_FB_TRIDENT is not set +# CONFIG_FB_ARK is not set +# CONFIG_FB_PM3 is not set +# CONFIG_FB_CARMINE is not set +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # -# Sound +# Display device support # -# CONFIG_SOUND is not set +# CONFIG_DISPLAY_SUPPORT is not set # -# HID Devices +# Console display driver support # +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set +CONFIG_FONTS=y +CONFIG_FONT_8x8=y +CONFIG_FONT_8x16=y +# CONFIG_FONT_6x11 is not set +# CONFIG_FONT_7x14 is not set +# CONFIG_FONT_PEARL_8x8 is not set +# CONFIG_FONT_ACORN_8x8 is not set +# CONFIG_FONT_MINI_4x6 is not set +# CONFIG_FONT_SUN8x16 is not set +# CONFIG_FONT_SUN12x22 is not set +# CONFIG_FONT_10x18 is not set +CONFIG_LOGO=y +# CONFIG_LOGO_LINUX_MONO is not set +# CONFIG_LOGO_LINUX_VGA16 is not set +# CONFIG_LOGO_LINUX_CLUT224 is not set +CONFIG_LOGO_SGI_CLUT224=y +# CONFIG_SOUND is not set +CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set +# CONFIG_HID_PID is not set # -# USB support -# -CONFIG_USB_ARCH_HAS_HCD=y -CONFIG_USB_ARCH_HAS_OHCI=y -CONFIG_USB_ARCH_HAS_EHCI=y -# CONFIG_USB is not set - -# -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' -# - -# -# USB Gadget Support -# -# CONFIG_USB_GADGET is not set - -# -# MMC/SD Card support +# Special HID drivers # +CONFIG_HID_COMPAT=y +# CONFIG_USB_SUPPORT is not set +# CONFIG_UWB is not set # CONFIG_MMC is not set - -# -# LED devices -# +# CONFIG_MEMSTICK is not set # CONFIG_NEW_LEDS is not set - -# -# LED drivers -# - -# -# LED Triggers -# - -# -# InfiniBand support -# +# CONFIG_ACCESSIBILITY is not set # CONFIG_INFINIBAND is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +# CONFIG_RTC_HCTOSYS is not set +# CONFIG_RTC_DEBUG is not set # -# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# RTC interfaces # +# CONFIG_RTC_INTF_SYSFS is not set +# CONFIG_RTC_INTF_PROC is not set +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set # -# Real Time Clock +# SPI RTC drivers # -# CONFIG_RTC_CLASS is not set # -# DMA Engine support +# Platform RTC drivers # -# CONFIG_DMA_ENGINE is not set +CONFIG_RTC_DRV_CMOS=y +# CONFIG_RTC_DRV_DS1286 is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_V3020 is not set # -# DMA Clients -# - -# -# DMA Devices -# - -# -# Auxiliary Display support -# - -# -# Virtualization +# on-CPU RTC drivers # +# CONFIG_DMADEVICES is not set +# CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems # CONFIG_EXT2_FS=y -# CONFIG_EXT2_FS_XATTR is not set +CONFIG_EXT2_FS_XATTR=y +CONFIG_EXT2_FS_POSIX_ACL=y +CONFIG_EXT2_FS_SECURITY=y # CONFIG_EXT2_FS_XIP is not set -# CONFIG_EXT3_FS is not set -# CONFIG_EXT4DEV_FS is not set +CONFIG_EXT3_FS=y +CONFIG_EXT3_FS_XATTR=y +CONFIG_EXT3_FS_POSIX_ACL=y +CONFIG_EXT3_FS_SECURITY=y +# CONFIG_EXT4_FS is not set +CONFIG_JBD=y +CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set CONFIG_FS_POSIX_ACL=y +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_GFS2_FS is not set # CONFIG_OCFS2_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_ROMFS_FS is not set +CONFIG_DNOTIFY=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y -# CONFIG_QUOTA is not set -CONFIG_DNOTIFY=y -# CONFIG_AUTOFS_FS is not set -# CONFIG_AUTOFS4_FS is not set -CONFIG_FUSE_FS=y +CONFIG_QUOTA=y +# CONFIG_QUOTA_NETLINK_INTERFACE is not set +CONFIG_PRINT_QUOTA_WARNING=y +CONFIG_QFMT_V1=m +CONFIG_QFMT_V2=m +CONFIG_QUOTACTL=y +CONFIG_AUTOFS_FS=m +CONFIG_AUTOFS4_FS=m +CONFIG_FUSE_FS=m CONFIG_GENERIC_ACL=y # # CD-ROM/DVD Filesystems # -# CONFIG_ISO9660_FS is not set -# CONFIG_UDF_FS is not set +CONFIG_ISO9660_FS=m +CONFIG_JOLIET=y +CONFIG_ZISOFS=y +CONFIG_UDF_FS=m +CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # -# CONFIG_MSDOS_FS is not set -# CONFIG_VFAT_FS is not set +CONFIG_FAT_FS=m +CONFIG_MSDOS_FS=m +CONFIG_VFAT_FS=m +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" # CONFIG_NTFS_FS is not set # @@ -896,11 +984,11 @@ CONFIG_GENERIC_ACL=y CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y CONFIG_CONFIGFS_FS=y # @@ -916,33 +1004,42 @@ CONFIG_CONFIGFS_FS=y # CONFIG_EFS_FS is not set # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set # CONFIG_NFS_V4 is not set -# CONFIG_NFS_DIRECTIO is not set -# CONFIG_NFSD is not set CONFIG_ROOT_NFS=y +CONFIG_NFSD=m +CONFIG_NFSD_V3=y +# CONFIG_NFSD_V3_ACL is not set +# CONFIG_NFSD_V4 is not set CONFIG_LOCKD=y CONFIG_LOCKD_V4=y +CONFIG_EXPORTFS=m CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y +# CONFIG_SUNRPC_REGISTER_V4 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set -# CONFIG_CIFS is not set +CONFIG_CIFS=m +# CONFIG_CIFS_STATS is not set +# CONFIG_CIFS_WEAK_PW_HASH is not set +# CONFIG_CIFS_UPCALL is not set +# CONFIG_CIFS_XATTR is not set +# CONFIG_CIFS_DEBUG2 is not set +# CONFIG_CIFS_EXPERIMENTAL is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set -# CONFIG_9P_FS is not set # # Partition Types @@ -953,45 +1050,83 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_AMIGA_PARTITION is not set # CONFIG_ATARI_PARTITION is not set # CONFIG_MAC_PARTITION is not set -# CONFIG_MSDOS_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set # CONFIG_LDM_PARTITION is not set CONFIG_SGI_PARTITION=y # CONFIG_ULTRIX_PARTITION is not set # CONFIG_SUN_PARTITION is not set # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set - -# -# Native Language Support -# -# CONFIG_NLS is not set - -# -# Distributed Lock Manager -# -CONFIG_DLM=y -CONFIG_DLM_TCP=y -# CONFIG_DLM_SCTP is not set -# CONFIG_DLM_DEBUG is not set - -# -# Profiling support -# -# CONFIG_PROFILING is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=m +CONFIG_NLS_CODEPAGE_737=m +CONFIG_NLS_CODEPAGE_775=m +CONFIG_NLS_CODEPAGE_850=m +CONFIG_NLS_CODEPAGE_852=m +CONFIG_NLS_CODEPAGE_855=m +CONFIG_NLS_CODEPAGE_857=m +CONFIG_NLS_CODEPAGE_860=m +CONFIG_NLS_CODEPAGE_861=m +CONFIG_NLS_CODEPAGE_862=m +CONFIG_NLS_CODEPAGE_863=m +CONFIG_NLS_CODEPAGE_864=m +CONFIG_NLS_CODEPAGE_865=m +CONFIG_NLS_CODEPAGE_866=m +CONFIG_NLS_CODEPAGE_869=m +CONFIG_NLS_CODEPAGE_936=m +CONFIG_NLS_CODEPAGE_950=m +CONFIG_NLS_CODEPAGE_932=m +CONFIG_NLS_CODEPAGE_949=m +CONFIG_NLS_CODEPAGE_874=m +CONFIG_NLS_ISO8859_8=m +CONFIG_NLS_CODEPAGE_1250=m +CONFIG_NLS_CODEPAGE_1251=m +CONFIG_NLS_ASCII=m +CONFIG_NLS_ISO8859_1=m +CONFIG_NLS_ISO8859_2=m +CONFIG_NLS_ISO8859_3=m +CONFIG_NLS_ISO8859_4=m +CONFIG_NLS_ISO8859_5=m +CONFIG_NLS_ISO8859_6=m +CONFIG_NLS_ISO8859_7=m +CONFIG_NLS_ISO8859_9=m +CONFIG_NLS_ISO8859_13=m +CONFIG_NLS_ISO8859_14=m +CONFIG_NLS_ISO8859_15=m +CONFIG_NLS_KOI8_R=m +CONFIG_NLS_KOI8_U=m +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set # # Kernel hacking # CONFIG_TRACE_IRQFLAGS_SUPPORT=y # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y -# CONFIG_MAGIC_SYSRQ is not set +CONFIG_FRAME_WARN=2048 +CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set -CONFIG_LOG_BUF_SHIFT=14 -CONFIG_CROSSCOMPILE=y +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y + +# +# Tracers +# +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y CONFIG_CMDLINE="" # @@ -1000,51 +1135,99 @@ CONFIG_CMDLINE="" CONFIG_KEYS=y CONFIG_KEYS_DEBUG_PROC_KEYS=y # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y # -# Cryptographic options +# Crypto core or helper # -CONFIG_CRYPTO=y +# CONFIG_CRYPTO_FIPS is not set CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_RNG=y CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_GF128MUL=y +CONFIG_CRYPTO_NULL=y +# CONFIG_CRYPTO_CRYPTD is not set +CONFIG_CRYPTO_AUTHENC=m +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=y +CONFIG_CRYPTO_LRW=y +CONFIG_CRYPTO_PCBC=y +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# CONFIG_CRYPTO_HMAC=y CONFIG_CRYPTO_XCBC=y -CONFIG_CRYPTO_NULL=y + +# +# Digest +# +CONFIG_CRYPTO_CRC32C=y CONFIG_CRYPTO_MD4=y CONFIG_CRYPTO_MD5=y +CONFIG_CRYPTO_MICHAEL_MIC=y +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set CONFIG_CRYPTO_SHA1=y CONFIG_CRYPTO_SHA256=y CONFIG_CRYPTO_SHA512=y -CONFIG_CRYPTO_WP512=y CONFIG_CRYPTO_TGR192=y -CONFIG_CRYPTO_GF128MUL=y -CONFIG_CRYPTO_ECB=y -CONFIG_CRYPTO_CBC=y -CONFIG_CRYPTO_PCBC=y -CONFIG_CRYPTO_LRW=y -CONFIG_CRYPTO_DES=y -CONFIG_CRYPTO_FCRYPT=y -CONFIG_CRYPTO_BLOWFISH=y -CONFIG_CRYPTO_TWOFISH=y -CONFIG_CRYPTO_TWOFISH_COMMON=y -CONFIG_CRYPTO_SERPENT=y +CONFIG_CRYPTO_WP512=y + +# +# Ciphers +# CONFIG_CRYPTO_AES=y +CONFIG_CRYPTO_ANUBIS=y +CONFIG_CRYPTO_ARC4=y +CONFIG_CRYPTO_BLOWFISH=y +CONFIG_CRYPTO_CAMELLIA=y CONFIG_CRYPTO_CAST5=y CONFIG_CRYPTO_CAST6=y -CONFIG_CRYPTO_TEA=y -CONFIG_CRYPTO_ARC4=y +CONFIG_CRYPTO_DES=y +CONFIG_CRYPTO_FCRYPT=y CONFIG_CRYPTO_KHAZAD=y -CONFIG_CRYPTO_ANUBIS=y +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +CONFIG_CRYPTO_SERPENT=y +CONFIG_CRYPTO_TEA=y +CONFIG_CRYPTO_TWOFISH=y +CONFIG_CRYPTO_TWOFISH_COMMON=y + +# +# Compression +# CONFIG_CRYPTO_DEFLATE=y -CONFIG_CRYPTO_MICHAEL_MIC=y -CONFIG_CRYPTO_CRC32C=y -CONFIG_CRYPTO_CAMELLIA=y +# CONFIG_CRYPTO_LZO is not set # -# Hardware crypto devices +# Random Number Generation # +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_HW=y +# CONFIG_CRYPTO_DEV_HIFN_795X is not set # # Library routines @@ -1052,10 +1235,15 @@ CONFIG_CRYPTO_CAMELLIA=y CONFIG_BITREVERSE=y # CONFIG_CRC_CCITT is not set CONFIG_CRC16=y +CONFIG_CRC_T10DIF=y +CONFIG_CRC_ITU_T=m CONFIG_CRC32=y +# CONFIG_CRC7 is not set CONFIG_LIBCRC32C=y +CONFIG_AUDIT_GENERIC=y CONFIG_ZLIB_INFLATE=y CONFIG_ZLIB_DEFLATE=y CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y -- cgit v1.1 From e5e774d8833de1a0037be2384efccadf16935675 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Sat, 13 Dec 2008 17:01:37 -0600 Subject: powerpc/fsl-booke: Fix problem with _tlbil_va being interrupted An example calling sequence which we did see: copy_user_highpage -> kmap_atomic -> flush_tlb_page -> _tlbil_va We got interrupted after setting up the MAS registers before the tlbwe and the interrupt handler that caused the interrupt also did a kmap_atomic (ide code) and thus on returning from the interrupt the MAS registers no longer contained the proper values. Since we dont save/restore MAS registers for normal interrupts we need to disable interrupts in _tlbil_va to ensure atomicity. Signed-off-by: Kumar Gala --- arch/powerpc/kernel/misc_32.S | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/kernel/misc_32.S b/arch/powerpc/kernel/misc_32.S index bdc8b0e..d108715 100644 --- a/arch/powerpc/kernel/misc_32.S +++ b/arch/powerpc/kernel/misc_32.S @@ -479,6 +479,8 @@ _GLOBAL(_tlbil_pid) * (no broadcast) */ _GLOBAL(_tlbil_va) + mfmsr r10 + wrteei 0 slwi r4,r4,16 mtspr SPRN_MAS6,r4 /* assume AS=0 for now */ tlbsx 0,r3 @@ -490,6 +492,7 @@ _GLOBAL(_tlbil_va) tlbwe msync isync + wrtee r10 blr #endif /* CONFIG_FSL_BOOKE */ -- cgit v1.1 From 442a902262e1dfc3f1298ceea5f3120fe2043904 Mon Sep 17 00:00:00 2001 From: Julia Lawall Date: Sat, 13 Dec 2008 16:37:59 +0100 Subject: [ARM] arch/arm/common/sa1111.c: Correct error handling code If it is reasonable to apply PTR_ERR to the result of calling clk_get, then that result should first be tested with IS_ERR, not with !. The semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // @@ expression E,E1; @@ if ( - E == NULL + IS_ERR(E) ) { <+... when != E = E1 PTR_ERR(E) ...+> } // Signed-off-by: Julia Lawall Signed-off-by: Russell King --- arch/arm/common/sa1111.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/common/sa1111.c b/arch/arm/common/sa1111.c index 47ccec9..ef12794 100644 --- a/arch/arm/common/sa1111.c +++ b/arch/arm/common/sa1111.c @@ -630,7 +630,7 @@ __sa1111_probe(struct device *me, struct resource *mem, int irq) return -ENOMEM; sachip->clk = clk_get(me, "SA1111_CLK"); - if (!sachip->clk) { + if (IS_ERR(sachip->clk)) { ret = PTR_ERR(sachip->clk); goto err_free; } -- cgit v1.1 From 3909845e26439148a484d1ac30bb65e5e0ff63ec Mon Sep 17 00:00:00 2001 From: Randy Dunlap Date: Mon, 1 Dec 2008 14:15:37 -0800 Subject: [ARM] fix kernel-doc syntax Fix kernel-doc notation to use correct syntax. Even though this should be moved to where the function is actually implemented... Signed-off-by: Randy Dunlap Signed-off-by: Andrew Morton Signed-off-by: Russell King --- arch/arm/mach-pxa/include/mach/reset.h | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-pxa/include/mach/reset.h b/arch/arm/mach-pxa/include/mach/reset.h index 7b8842c..31e6a7b 100644 --- a/arch/arm/mach-pxa/include/mach/reset.h +++ b/arch/arm/mach-pxa/include/mach/reset.h @@ -12,9 +12,8 @@ extern void clear_reset_status(unsigned int mask); /** * init_gpio_reset() - register GPIO as reset generator - * - * @gpio - gpio nr - * @output - set gpio as out/low instead of input during normal work + * @gpio: gpio nr + * @output: set gpio as out/low instead of input during normal work */ extern int init_gpio_reset(int gpio, int output); -- cgit v1.1 From ae8d04e2ecbb233926860e9ce145eac19c7835dc Mon Sep 17 00:00:00 2001 From: Zachary Amsden Date: Sat, 13 Dec 2008 12:36:58 -0800 Subject: x86 Fix VMI crash on boot in 2.6.28-rc8 VMI initialiation can relocate the fixmap, causing early_ioremap to malfunction if it is initialized before the relocation. To fix this, VMI activation is split into two phases; the detection, which must happen before setting up ioremap, and the activation, which must happen after parsing early boot parameters. This fixes a crash on boot when VMI is enabled under VMware. Signed-off-by: Zachary Amsden Signed-off-by: Linus Torvalds --- arch/x86/include/asm/vmi.h | 8 +++++++- arch/x86/kernel/setup.c | 12 +++++------- arch/x86/kernel/smpboot.c | 2 -- arch/x86/kernel/vmi_32.c | 16 +++++++++++----- 4 files changed, 23 insertions(+), 15 deletions(-) (limited to 'arch') diff --git a/arch/x86/include/asm/vmi.h b/arch/x86/include/asm/vmi.h index b7c0dea..61e08c0 100644 --- a/arch/x86/include/asm/vmi.h +++ b/arch/x86/include/asm/vmi.h @@ -223,9 +223,15 @@ struct pci_header { } __attribute__((packed)); /* Function prototypes for bootstrapping */ +#ifdef CONFIG_VMI extern void vmi_init(void); +extern void vmi_activate(void); extern void vmi_bringup(void); -extern void vmi_apply_boot_page_allocations(void); +#else +static inline void vmi_init(void) {} +static inline void vmi_activate(void) {} +static inline void vmi_bringup(void) {} +#endif /* State needed to start an application processor in an SMP system. */ struct vmi_ap_state { diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c index 9d5674f..bdec76e 100644 --- a/arch/x86/kernel/setup.c +++ b/arch/x86/kernel/setup.c @@ -794,6 +794,9 @@ void __init setup_arch(char **cmdline_p) printk(KERN_INFO "Command line: %s\n", boot_command_line); #endif + /* VMI may relocate the fixmap; do this before touching ioremap area */ + vmi_init(); + early_cpu_init(); early_ioremap_init(); @@ -880,13 +883,8 @@ void __init setup_arch(char **cmdline_p) check_efer(); #endif -#if defined(CONFIG_VMI) && defined(CONFIG_X86_32) - /* - * Must be before kernel pagetables are setup - * or fixmap area is touched. - */ - vmi_init(); -#endif + /* Must be before kernel pagetables are setup */ + vmi_activate(); /* after early param, so could get panic from serial */ reserve_early_setup_data(); diff --git a/arch/x86/kernel/smpboot.c b/arch/x86/kernel/smpboot.c index 7b10933..f71f96f 100644 --- a/arch/x86/kernel/smpboot.c +++ b/arch/x86/kernel/smpboot.c @@ -294,9 +294,7 @@ static void __cpuinit start_secondary(void *unused) * fragile that we want to limit the things done here to the * most necessary things. */ -#ifdef CONFIG_VMI vmi_bringup(); -#endif cpu_init(); preempt_disable(); smp_callin(); diff --git a/arch/x86/kernel/vmi_32.c b/arch/x86/kernel/vmi_32.c index 8b6c393..22fd657 100644 --- a/arch/x86/kernel/vmi_32.c +++ b/arch/x86/kernel/vmi_32.c @@ -960,8 +960,6 @@ static inline int __init activate_vmi(void) void __init vmi_init(void) { - unsigned long flags; - if (!vmi_rom) probe_vmi_rom(); else @@ -973,13 +971,21 @@ void __init vmi_init(void) reserve_top_address(-vmi_rom->virtual_top); - local_irq_save(flags); - activate_vmi(); - #ifdef CONFIG_X86_IO_APIC /* This is virtual hardware; timer routing is wired correctly */ no_timer_check = 1; #endif +} + +void vmi_activate(void) +{ + unsigned long flags; + + if (!vmi_rom) + return; + + local_irq_save(flags); + activate_vmi(); local_irq_restore(flags & X86_EFLAGS_IF); } -- cgit v1.1 From 67306da610a3e4824192e92888634d3d8700bfc1 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 14 Dec 2008 18:01:44 +0000 Subject: [ARM] Ensure linux/hardirqs.h is included where required ... for the removal of it from asm-generic/local.h Signed-off-by: Russell King --- arch/arm/kernel/traps.c | 1 + arch/arm/mm/fault.c | 1 + 2 files changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c index 57e6874..79abc4d 100644 --- a/arch/arm/kernel/traps.c +++ b/arch/arm/kernel/traps.c @@ -18,6 +18,7 @@ #include #include #include +#include #include #include diff --git a/arch/arm/mm/fault.c b/arch/arm/mm/fault.c index 2df8d9f..22c9530 100644 --- a/arch/arm/mm/fault.c +++ b/arch/arm/mm/fault.c @@ -11,6 +11,7 @@ #include #include #include +#include #include #include #include -- cgit v1.1 From 48f797de550d39ea35552646c34149991362ff7f Mon Sep 17 00:00:00 2001 From: Brian King Date: Thu, 4 Dec 2008 04:07:54 +0000 Subject: powerpc: Check for valid hugepage size in hugetlb_get_unmapped_area It looks like most of the hugetlb code is doing the correct thing if hugepages are not supported, but the mmap code is not. If we get into the mmap code when hugepages are not supported, such as in an LPAR which is running Active Memory Sharing, we can oops the kernel. This fixes the oops being seen in this path. oops: Kernel access of bad area, sig: 11 [#1] SMP NR_CPUS=1024 NUMA pSeries Modules linked in: nfs(N) lockd(N) nfs_acl(N) sunrpc(N) ipv6(N) fuse(N) loop(N) dm_mod(N) sg(N) ibmveth(N) sd_mod(N) crc_t10dif(N) ibmvscsic(N) scsi_transport_srp(N) scsi_tgt(N) scsi_mod(N) Supported: No NIP: c000000000038d60 LR: c00000000003945c CTR: c0000000000393f0 REGS: c000000077e7b830 TRAP: 0300 Tainted: G (2.6.27.5-bz50170-2-ppc64) MSR: 8000000000009032 CR: 44000448 XER: 20000001 DAR: c000002000af90a8, DSISR: 0000000040000000 TASK = c00000007c1b8600[4019] 'hugemmap01' THREAD: c000000077e78000 CPU: 6 GPR00: 0000001fffffffe0 c000000077e7bab0 c0000000009a4e78 0000000000000000 GPR04: 0000000000010000 0000000000000001 00000000ffffffff 0000000000000001 GPR08: 0000000000000000 c000000000af90c8 0000000000000001 0000000000000000 GPR12: 000000000000003f c000000000a73880 0000000000000000 0000000000000000 GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000010000 GPR20: 0000000000000000 0000000000000003 0000000000010000 0000000000000001 GPR24: 0000000000000003 0000000000000000 0000000000000001 ffffffffffffffb5 GPR28: c000000077ca2e80 0000000000000000 c00000000092af78 0000000000010000 NIP [c000000000038d60] .slice_get_unmapped_area+0x6c/0x4e0 LR [c00000000003945c] .hugetlb_get_unmapped_area+0x6c/0x80 Call Trace: [c000000077e7bbc0] [c00000000003945c] .hugetlb_get_unmapped_area+0x6c/0x80 [c000000077e7bc30] [c000000000107e30] .get_unmapped_area+0x64/0xd8 [c000000077e7bcb0] [c00000000010b140] .do_mmap_pgoff+0x140/0x420 [c000000077e7bd80] [c00000000000bf5c] .sys_mmap+0xc4/0x140 [c000000077e7be30] [c0000000000086b4] syscall_exit+0x0/0x40 Instruction dump: fac1ffb0 fae1ffb8 fb01ffc0 fb21ffc8 fb41ffd0 fb61ffd8 fb81ffe0 fbc1fff0 fbe1fff8 f821fef1 f8c10158 f8e10160 <7d49002e> f9010168 e92d01b0 eb4902b0 Signed-off-by: Brian King Signed-off-by: Paul Mackerras --- arch/powerpc/mm/hugetlbpage.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/mm/hugetlbpage.c b/arch/powerpc/mm/hugetlbpage.c index 7bbf4e4..f0c3b88 100644 --- a/arch/powerpc/mm/hugetlbpage.c +++ b/arch/powerpc/mm/hugetlbpage.c @@ -507,6 +507,9 @@ unsigned long hugetlb_get_unmapped_area(struct file *file, unsigned long addr, { struct hstate *hstate = hstate_file(file); int mmu_psize = shift_to_mmu_psize(huge_page_shift(hstate)); + + if (!mmu_huge_psizes[mmu_psize]) + return -EINVAL; return slice_get_unmapped_area(addr, len, flags, mmu_psize, 1, 0); } -- cgit v1.1 From a4c74ddd5ea3db53fc73d29c222b22656a7d05be Mon Sep 17 00:00:00 2001 From: Dave Hansen Date: Thu, 11 Dec 2008 08:36:06 +0000 Subject: powerpc: Fix bootmem reservation on uninitialized node careful_allocation() was calling into the bootmem allocator for nodes which had not been fully initialized and caused a previous bug: http://patchwork.ozlabs.org/patch/10528/ So, I merged a few broken out loops in do_init_bootmem() to fix it. That changed the code ordering. I think this bug is triggered by having reserved areas for a node which are spanned by another node's contents. In the mark_reserved_regions_for_nid() code, we attempt to reserve the area for a node before we have allocated the NODE_DATA() for that nid. We do this since I reordered that loop. I suck. This is causing crashes at bootup on some systems, as reported by Jon Tollefson. This may only present on some systems that have 16GB pages reserved. But, it can probably happen on any system that is trying to reserve large swaths of memory that happen to span other nodes' contents. This commit ensures that we do not touch bootmem for any node which has not been initialized, and also removes a compile warning about an unused variable. Signed-off-by: Dave Hansen Signed-off-by: Paul Mackerras --- arch/powerpc/mm/numa.c | 16 +++++++++++----- 1 file changed, 11 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/mm/numa.c b/arch/powerpc/mm/numa.c index a8397bb..cf81049 100644 --- a/arch/powerpc/mm/numa.c +++ b/arch/powerpc/mm/numa.c @@ -901,10 +901,17 @@ static void mark_reserved_regions_for_nid(int nid) if (end_pfn > node_ar.end_pfn) reserve_size = (node_ar.end_pfn << PAGE_SHIFT) - (start_pfn << PAGE_SHIFT); - dbg("reserve_bootmem %lx %lx nid=%d\n", physbase, - reserve_size, node_ar.nid); - reserve_bootmem_node(NODE_DATA(node_ar.nid), physbase, - reserve_size, BOOTMEM_DEFAULT); + /* + * Only worry about *this* node, others may not + * yet have valid NODE_DATA(). + */ + if (node_ar.nid == nid) { + dbg("reserve_bootmem %lx %lx nid=%d\n", + physbase, reserve_size, node_ar.nid); + reserve_bootmem_node(NODE_DATA(node_ar.nid), + physbase, reserve_size, + BOOTMEM_DEFAULT); + } /* * if reserved region is contained in the active region * then done. @@ -929,7 +936,6 @@ static void mark_reserved_regions_for_nid(int nid) void __init do_init_bootmem(void) { int nid; - unsigned int i; min_low_pfn = 0; max_low_pfn = lmb_end_of_DRAM() >> PAGE_SHIFT; -- cgit v1.1 From 23e0e8afafd9ac065d81506524adf3339584044b Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Fri, 12 Dec 2008 09:19:50 +0000 Subject: powerpc/cell/axon-msi: Fix MSI after kexec Commit d015fe995 'powerpc/cell/axon-msi: Retry on missing interrupt' has turned a rare failure to kexec on QS22 into a reproducible error, which we have now analysed. The problem is that after a kexec, the MSIC hardware still points into the middle of the old ring buffer. We set up the ring buffer during reboot, but not the offset into it. On older kernels, this would cause a storm of thousands of spurious interrupts after a kexec, which would most of the time get dropped silently. With the new code, we time out on each interrupt, waiting for it to become valid. If more interrupts come in that we time out on, this goes on indefinitely, which eventually leads to a hard crash. The solution in this commit is to read the current offset from the MSIC when reinitializing it. This now works correctly, as expected. Reported-by: Dirk Herrendoerfer Signed-off-by: Arnd Bergmann Acked-by: Michael Ellerman Signed-off-by: Paul Mackerras --- arch/powerpc/platforms/cell/axon_msi.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/powerpc/platforms/cell/axon_msi.c b/arch/powerpc/platforms/cell/axon_msi.c index 442cf36..0ce45c2 100644 --- a/arch/powerpc/platforms/cell/axon_msi.c +++ b/arch/powerpc/platforms/cell/axon_msi.c @@ -413,6 +413,9 @@ static int axon_msi_probe(struct of_device *device, MSIC_CTRL_IRQ_ENABLE | MSIC_CTRL_ENABLE | MSIC_CTRL_FIFO_SIZE); + msic->read_offset = dcr_read(msic->dcr_host, MSIC_WRITE_OFFSET_REG) + & MSIC_FIFO_SIZE_MASK; + device->dev.platform_data = msic; ppc_md.setup_msi_irqs = axon_msi_setup_msi_irqs; -- cgit v1.1 From f9d62c009637f9581cdd7f6e430f8eec511c8587 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Mon, 8 Dec 2008 11:45:37 +0900 Subject: sh: Disable GENERIC_HARDIRQS_NO__DO_IRQ for unconverted platforms. Presently limited to Cayman, Dreamcast, Microdev, and SystemH 7751. Re-enable it for everyone once these have been fixed up. Signed-off-by: Paul Mundt --- arch/sh/Kconfig | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig index 80119b3..5c9cbfc 100644 --- a/arch/sh/Kconfig +++ b/arch/sh/Kconfig @@ -55,6 +55,8 @@ config GENERIC_HARDIRQS config GENERIC_HARDIRQS_NO__DO_IRQ def_bool y + depends on SUPERH32 && (!SH_DREAMCAST && !SH_SH4202_MICRODEV && \ + !SH_7751_SYSTEMH && !HD64461) config GENERIC_IRQ_PROBE def_bool y -- cgit v1.1 From 83fd5cc6481c6b7fa8b45f8a7e0aa7120213430b Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Tue, 16 Dec 2008 19:17:11 +0100 Subject: AMD IOMMU: allocate rlookup_table with __GFP_ZERO Impact: fix bug which can lead to panic in prealloc_protection_domains() Signed-off-by: Joerg Roedel --- arch/x86/kernel/amd_iommu_init.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/kernel/amd_iommu_init.c b/arch/x86/kernel/amd_iommu_init.c index 30ae270..c90a15e 100644 --- a/arch/x86/kernel/amd_iommu_init.c +++ b/arch/x86/kernel/amd_iommu_init.c @@ -1074,7 +1074,8 @@ int __init amd_iommu_init(void) goto free; /* IOMMU rlookup table - find the IOMMU for a specific device */ - amd_iommu_rlookup_table = (void *)__get_free_pages(GFP_KERNEL, + amd_iommu_rlookup_table = (void *)__get_free_pages( + GFP_KERNEL | __GFP_ZERO, get_order(rlookup_table_size)); if (amd_iommu_rlookup_table == NULL) goto free; -- cgit v1.1 From cf9b303e55da810255638c0b616b1a3f7eda9320 Mon Sep 17 00:00:00 2001 From: Andi Kleen Date: Mon, 15 Dec 2008 23:33:10 +0100 Subject: x86: re-enable MCE on secondary CPUS after suspend/resume Impact: fix disabled MCE after resume Don't prevent multiple initialization of MCEs. Back from early prehistory mcheck_init() has a reentry check. Presumably that was needed in very old kernels to prevent it entering twice. But as Andreas points out this prevents CPU hotplug (and therefore resume) to correctly reinitialize MCEs when a AP boots again after being offlined. Just drop the check. Reported-by: Andreas Herrmann Signed-off-by: Andi Kleen Tested-by: Andreas Herrmann Signed-off-by: Ingo Molnar --- arch/x86/kernel/cpu/mcheck/mce_64.c | 3 --- 1 file changed, 3 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/cpu/mcheck/mce_64.c b/arch/x86/kernel/cpu/mcheck/mce_64.c index 4b031a4..1c83803 100644 --- a/arch/x86/kernel/cpu/mcheck/mce_64.c +++ b/arch/x86/kernel/cpu/mcheck/mce_64.c @@ -510,12 +510,9 @@ static void __cpuinit mce_cpu_features(struct cpuinfo_x86 *c) */ void __cpuinit mcheck_init(struct cpuinfo_x86 *c) { - static cpumask_t mce_cpus = CPU_MASK_NONE; - mce_cpu_quirks(c); if (mce_dont_init || - cpu_test_and_set(smp_processor_id(), mce_cpus) || !mce_available(c)) return; -- cgit v1.1 From 48a1b10aff588833b73994704c47bbd0deb73e9c Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Thu, 11 Dec 2008 00:15:01 -0800 Subject: x86, sparseirq: move irq_desc according to smp_affinity, v7 Impact: improve NUMA handling by migrating irq_desc on smp_affinity changes if CONFIG_NUMA_MIGRATE_IRQ_DESC is set: - make irq_desc to go with affinity aka irq_desc moving etc - call move_irq_desc in irq_complete_move() - legacy irq_desc is not moved, because they are allocated via static array for logical apic mode, need to add move_desc_in_progress_in_same_domain, otherwise it will not be moved ==> also could need two phases to get irq_desc moved. Signed-off-by: Yinghai Lu Signed-off-by: Ingo Molnar --- arch/x86/Kconfig | 9 +++ arch/x86/kernel/io_apic.c | 142 +++++++++++++++++++++++++++++++++++++++++++++- 2 files changed, 150 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 8943c13..2907353 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -248,6 +248,15 @@ config SPARSE_IRQ If you don't know what to do here, say Y. +config NUMA_MIGRATE_IRQ_DESC + bool "Move irq desc when changing irq smp_affinity" + depends on SPARSE_IRQ && SMP + default n + help + This enables moving irq_desc to cpu/node that irq will use handled. + + If you don't know what to do here, say N. + config X86_FIND_SMP_CONFIG def_bool y depends on X86_MPPARSE || X86_VOYAGER diff --git a/arch/x86/kernel/io_apic.c b/arch/x86/kernel/io_apic.c index a1a2e07..bfe1245 100644 --- a/arch/x86/kernel/io_apic.c +++ b/arch/x86/kernel/io_apic.c @@ -141,6 +141,9 @@ struct irq_cfg { unsigned move_cleanup_count; u8 vector; u8 move_in_progress : 1; +#ifdef CONFIG_NUMA_MIGRATE_IRQ_DESC + u8 move_desc_pending : 1; +#endif }; /* irq_cfg is indexed by the sum of all RTEs in all I/O APICs. */ @@ -223,6 +226,121 @@ void arch_init_chip_data(struct irq_desc *desc, int cpu) } } +#ifdef CONFIG_NUMA_MIGRATE_IRQ_DESC + +static void +init_copy_irq_2_pin(struct irq_cfg *old_cfg, struct irq_cfg *cfg, int cpu) +{ + struct irq_pin_list *old_entry, *head, *tail, *entry; + + cfg->irq_2_pin = NULL; + old_entry = old_cfg->irq_2_pin; + if (!old_entry) + return; + + entry = get_one_free_irq_2_pin(cpu); + if (!entry) + return; + + entry->apic = old_entry->apic; + entry->pin = old_entry->pin; + head = entry; + tail = entry; + old_entry = old_entry->next; + while (old_entry) { + entry = get_one_free_irq_2_pin(cpu); + if (!entry) { + entry = head; + while (entry) { + head = entry->next; + kfree(entry); + entry = head; + } + /* still use the old one */ + return; + } + entry->apic = old_entry->apic; + entry->pin = old_entry->pin; + tail->next = entry; + tail = entry; + old_entry = old_entry->next; + } + + tail->next = NULL; + cfg->irq_2_pin = head; +} + +static void free_irq_2_pin(struct irq_cfg *old_cfg, struct irq_cfg *cfg) +{ + struct irq_pin_list *entry, *next; + + if (old_cfg->irq_2_pin == cfg->irq_2_pin) + return; + + entry = old_cfg->irq_2_pin; + + while (entry) { + next = entry->next; + kfree(entry); + entry = next; + } + old_cfg->irq_2_pin = NULL; +} + +void arch_init_copy_chip_data(struct irq_desc *old_desc, + struct irq_desc *desc, int cpu) +{ + struct irq_cfg *cfg; + struct irq_cfg *old_cfg; + + cfg = get_one_free_irq_cfg(cpu); + + if (!cfg) + return; + + desc->chip_data = cfg; + + old_cfg = old_desc->chip_data; + + memcpy(cfg, old_cfg, sizeof(struct irq_cfg)); + + init_copy_irq_2_pin(old_cfg, cfg, cpu); +} + +static void free_irq_cfg(struct irq_cfg *old_cfg) +{ + kfree(old_cfg); +} + +void arch_free_chip_data(struct irq_desc *old_desc, struct irq_desc *desc) +{ + struct irq_cfg *old_cfg, *cfg; + + old_cfg = old_desc->chip_data; + cfg = desc->chip_data; + + if (old_cfg == cfg) + return; + + if (old_cfg) { + free_irq_2_pin(old_cfg, cfg); + free_irq_cfg(old_cfg); + old_desc->chip_data = NULL; + } +} + +static void set_extra_move_desc(struct irq_desc *desc, cpumask_t mask) +{ + struct irq_cfg *cfg = desc->chip_data; + + if (!cfg->move_in_progress) { + /* it means that domain is not changed */ + if (!cpus_intersects(desc->affinity, mask)) + cfg->move_desc_pending = 1; + } +} +#endif + #else static struct irq_cfg *irq_cfg(unsigned int irq) { @@ -231,9 +349,11 @@ static struct irq_cfg *irq_cfg(unsigned int irq) #endif +#ifndef CONFIG_NUMA_MIGRATE_IRQ_DESC static inline void set_extra_move_desc(struct irq_desc *desc, cpumask_t mask) { } +#endif struct io_apic { unsigned int index; @@ -2346,14 +2466,34 @@ static void irq_complete_move(struct irq_desc **descp) struct irq_cfg *cfg = desc->chip_data; unsigned vector, me; - if (likely(!cfg->move_in_progress)) + if (likely(!cfg->move_in_progress)) { +#ifdef CONFIG_NUMA_MIGRATE_IRQ_DESC + if (likely(!cfg->move_desc_pending)) + return; + + /* domain is not change, but affinity is changed */ + me = smp_processor_id(); + if (cpu_isset(me, desc->affinity)) { + *descp = desc = move_irq_desc(desc, me); + /* get the new one */ + cfg = desc->chip_data; + cfg->move_desc_pending = 0; + } +#endif return; + } vector = ~get_irq_regs()->orig_ax; me = smp_processor_id(); if ((vector == cfg->vector) && cpu_isset(me, cfg->domain)) { cpumask_t cleanup_mask; +#ifdef CONFIG_NUMA_MIGRATE_IRQ_DESC + *descp = desc = move_irq_desc(desc, me); + /* get the new one */ + cfg = desc->chip_data; +#endif + cpus_and(cleanup_mask, cfg->old_domain, cpu_online_map); cfg->move_cleanup_count = cpus_weight(cleanup_mask); send_IPI_mask(cleanup_mask, IRQ_MOVE_CLEANUP_VECTOR); -- cgit v1.1 From 17483a1f34c970e6c2cb8c082d4441bfabbe88a9 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Fri, 12 Dec 2008 13:14:18 -0800 Subject: sparseirq: fix !SMP building, #2 Impact: build fix make intr_remapping.c to include smp.h, so could use boot_cpu_id there also remove old change that disabling sparseirq with !SMP Signed-off-by: Yinghai Lu Signed-off-by: Ingo Molnar --- arch/x86/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 2907353..60a0088 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -240,7 +240,7 @@ config X86_HAS_BOOT_CPU_ID config SPARSE_IRQ bool "Support sparse irq numbering" - depends on (PCI_MSI || HT_IRQ) && SMP + depends on PCI_MSI || HT_IRQ default y help This enables support for sparse irq, esp for msi/msi-x. You may need -- cgit v1.1 From 878a5535957b563c447d32866a9e606c55fef091 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Tue, 16 Dec 2008 21:55:44 -0800 Subject: sparc: We need to implement arch_ptrace_stop(). In order to always provide fully synchronized state to the debugger, we might need to do a synchronize_user_stack(). A pair of hooks, arch_ptrace_stop_needed() and arch_ptrace_stop(), exist to handle this kind of situation. It was created for the sake of IA64. Use them, to flush the kernel side cached register windows to the user stack, when necessary. Signed-off-by: David S. Miller --- arch/sparc/include/asm/ptrace_32.h | 10 ++++++++++ arch/sparc/include/asm/ptrace_64.h | 9 +++++++++ 2 files changed, 19 insertions(+) (limited to 'arch') diff --git a/arch/sparc/include/asm/ptrace_32.h b/arch/sparc/include/asm/ptrace_32.h index d409c4f..4cef450 100644 --- a/arch/sparc/include/asm/ptrace_32.h +++ b/arch/sparc/include/asm/ptrace_32.h @@ -62,6 +62,8 @@ struct sparc_stackf { #ifdef __KERNEL__ +#include + static inline bool pt_regs_is_syscall(struct pt_regs *regs) { return (regs->psr & PSR_SYSCALL); @@ -72,6 +74,14 @@ static inline bool pt_regs_clear_syscall(struct pt_regs *regs) return (regs->psr &= ~PSR_SYSCALL); } +#define arch_ptrace_stop_needed(exit_code, info) \ +({ flush_user_windows(); \ + current_thread_info()->w_saved != 0; \ +}) + +#define arch_ptrace_stop(exit_code, info) \ + synchronize_user_stack() + #define user_mode(regs) (!((regs)->psr & PSR_PS)) #define instruction_pointer(regs) ((regs)->pc) #define user_stack_pointer(regs) ((regs)->u_regs[UREG_FP]) diff --git a/arch/sparc/include/asm/ptrace_64.h b/arch/sparc/include/asm/ptrace_64.h index 84e969f..cd6fbfc 100644 --- a/arch/sparc/include/asm/ptrace_64.h +++ b/arch/sparc/include/asm/ptrace_64.h @@ -114,6 +114,7 @@ struct sparc_trapf { #ifdef __KERNEL__ #include +#include static inline int pt_regs_trap_type(struct pt_regs *regs) { @@ -130,6 +131,14 @@ static inline bool pt_regs_clear_syscall(struct pt_regs *regs) return (regs->tstate &= ~TSTATE_SYSCALL); } +#define arch_ptrace_stop_needed(exit_code, info) \ +({ flush_user_windows(); \ + get_thread_wsaved() != 0; \ +}) + +#define arch_ptrace_stop(exit_code, info) \ + synchronize_user_stack() + struct global_reg_snapshot { unsigned long tstate; unsigned long tpc; -- cgit v1.1 From c1892cb8d2787280a5d9aacf8f58cf18f5b6fb2f Mon Sep 17 00:00:00 2001 From: Hans-Christian Egtvedt Date: Wed, 26 Nov 2008 11:40:42 +0100 Subject: avr32: remove .note.gnu.build-id section when making vmlinux.bin This patch will remove the section .note.gnu.build-id added in binutils 2.18 from the vmlinux.bin binary. Not removing this section results in a huge multiple gigabyte binary and likewize large uImage. Signed-off-by: Hans-Christian Egtvedt Signed-off-by: Haavard Skinnemoen --- arch/avr32/boot/images/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/avr32/boot/images/Makefile b/arch/avr32/boot/images/Makefile index 219720a..1848bf0 100644 --- a/arch/avr32/boot/images/Makefile +++ b/arch/avr32/boot/images/Makefile @@ -10,7 +10,7 @@ MKIMAGE := $(srctree)/scripts/mkuboot.sh extra-y := vmlinux.bin vmlinux.gz -OBJCOPYFLAGS_vmlinux.bin := -O binary +OBJCOPYFLAGS_vmlinux.bin := -O binary -R .note.gnu.build-id $(obj)/vmlinux.bin: vmlinux FORCE $(call if_changed,objcopy) -- cgit v1.1 From cf558d25e5c9f70fa0279c9b7b8b4aed7cae9bd4 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Wed, 17 Dec 2008 15:06:01 +0100 Subject: AMD IOMMU: set cmd buffer pointers to zero manually Impact: set cmd buffer head and tail pointers to zero in case nobody else did Signed-off-by: Joerg Roedel --- arch/x86/kernel/amd_iommu_init.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch') diff --git a/arch/x86/kernel/amd_iommu_init.c b/arch/x86/kernel/amd_iommu_init.c index c90a15e..c6cc228 100644 --- a/arch/x86/kernel/amd_iommu_init.c +++ b/arch/x86/kernel/amd_iommu_init.c @@ -427,6 +427,10 @@ static u8 * __init alloc_command_buffer(struct amd_iommu *iommu) memcpy_toio(iommu->mmio_base + MMIO_CMD_BUF_OFFSET, &entry, sizeof(entry)); + /* set head and tail to zero manually */ + writel(0x00, iommu->mmio_base + MMIO_CMD_HEAD_OFFSET); + writel(0x00, iommu->mmio_base + MMIO_CMD_TAIL_OFFSET); + iommu_feature_enable(iommu, CONTROL_CMDBUF_EN); return cmd_buf; -- cgit v1.1 From 84df81759590ad16b0024cf46b3423cca76b2e07 Mon Sep 17 00:00:00 2001 From: Joerg Roedel Date: Wed, 17 Dec 2008 16:36:44 +0100 Subject: AMD IOMMU: panic if completion wait loop fails Impact: prevents data corruption after a failed completion wait loop Signed-off-by: Joerg Roedel --- arch/x86/kernel/amd_iommu.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/amd_iommu.c b/arch/x86/kernel/amd_iommu.c index a7b6dec..0a60d60 100644 --- a/arch/x86/kernel/amd_iommu.c +++ b/arch/x86/kernel/amd_iommu.c @@ -235,8 +235,9 @@ static int iommu_completion_wait(struct amd_iommu *iommu) status &= ~MMIO_STATUS_COM_WAIT_INT_MASK; writel(status, iommu->mmio_base + MMIO_STATUS_OFFSET); - if (unlikely((i == EXIT_LOOP_COUNT) && printk_ratelimit())) - printk(KERN_WARNING "AMD IOMMU: Completion wait loop failed\n"); + if (unlikely(i == EXIT_LOOP_COUNT)) + panic("AMD IOMMU: Completion wait loop failed\n"); + out: spin_unlock_irqrestore(&iommu->lock, flags); -- cgit v1.1 From 28707af01b8912e701e3c5b619ff8f6dde8f2e81 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Wed, 17 Dec 2008 18:24:15 +0800 Subject: powerpc/fsl-booke: Fix the miss interrupt restore The commit e5e774d8833de1a0037be2384efccadf16935675 powerpc/fsl-booke: Fix problem with _tlbil_va being interrupted introduce one issue. that casue the problem like this: Kernel BUG at c00b19fc [verbose debug info unavailable] Oops: Exception in kernel mode, sig: 5 [#1] MPC8572 DS Modules linked in: NIP: c00b19fc LR: c00b1c34 CTR: c0064e88 REGS: ef02b7b0 TRAP: 0700 Not tainted (2.6.28-rc8-00057-g1bda712) MSR: 00021000 CR: 44048028 XER: 20000000 TASK = ef02c000[1] 'init' THREAD: ef02a000 GPR00: 00000001 ef02b860 ef02c000 eec201a0 c0dec2c0 00000000 000078a1 00000400 GPR08: c00b4e40 000078a1 c048ec00 a1780000 44048028 ecd26917 00000001 ef02b948 GPR16: ffffffea 0000020c 00000000 00000000 00000003 0000000a 00000000 000078a1 GPR24: eec201a0 00000000 ed849000 00000400 ef02b95c 00000001 ef02b978 ef02b984 NIP [c00b19fc] __find_get_block+0x24/0x238 LR [c00b1c34] __getblk+0x24/0x2a0 Call Trace: [ef02b860] [c017b768] generic_make_request+0x290/0x328 (unreliable) [ef02b8b0] [c00b1c34] __getblk+0x24/0x2a0 [ef02b910] [c00b4ae4] __bread+0x14/0xf8 [ef02b920] [c00fc228] ext2_get_branch+0xf0/0x138 [ef02b940] [c00fcc88] ext2_get_block+0xb8/0x828 [ef02ba00] [c00bbdc8] do_mpage_readpage+0x188/0x808 [ef02bac0] [c00bc5b4] mpage_readpages+0xec/0x144 [ef02bb50] [c00fba38] ext2_readpages+0x24/0x34 [ef02bb60] [c006ade0] __do_page_cache_readahead+0x150/0x230 [ef02bbb0] [c0064bdc] filemap_fault+0x31c/0x3e0 [ef02bbf0] [c00728b8] __do_fault+0x60/0x5b0 [ef02bc50] [c0011e0c] do_page_fault+0x2d8/0x4c4 [ef02bd10] [c000ed90] handle_page_fault+0xc/0x80 [ef02bdd0] [c00c7adc] set_brk+0x74/0x9c [ef02bdf0] [c00c9274] load_elf_binary+0x70c/0x1180 [ef02be70] [c00945f0] search_binary_handler+0xa8/0x274 [ef02bea0] [c0095818] do_execve+0x19c/0x1d4 [ef02bed0] [c000766c] sys_execve+0x58/0x84 [ef02bef0] [c000e950] ret_from_syscall+0x0/0x3c [ef02bfb0] [c009c6fc] sys_dup+0x24/0x6c [ef02bfc0] [c0001e04] init_post+0xb0/0xf0 [ef02bfd0] [c046c1ac] kernel_init+0xcc/0xf4 [ef02bff0] [c000e6d0] kernel_thread+0x4c/0x68 Instruction dump: 4bffffa4 813f000c 4bffffac 9421ffb0 7c0802a6 7d800026 90010054 bf210034 91810030 7c0000a6 68008000 54008ffe <0f000000> 3d20c04e 3b29ffb8 38000008 The issue was the beqlr returns early but we haven't reenabled interrupts. Signed-off-by: Dave Liu Signed-off-by: Kumar Gala --- arch/powerpc/kernel/misc_32.S | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/kernel/misc_32.S b/arch/powerpc/kernel/misc_32.S index d108715..5c33bc1 100644 --- a/arch/powerpc/kernel/misc_32.S +++ b/arch/powerpc/kernel/misc_32.S @@ -486,13 +486,13 @@ _GLOBAL(_tlbil_va) tlbsx 0,r3 mfspr r4,SPRN_MAS1 /* check valid */ andis. r3,r4,MAS1_VALID@h - beqlr + beq 1f rlwinm r4,r4,0,1,31 mtspr SPRN_MAS1,r4 tlbwe msync isync - wrtee r10 +1: wrtee r10 blr #endif /* CONFIG_FSL_BOOKE */ -- cgit v1.1 From af4d3643864ee5fcba0c97d77a424fa0b0346f8e Mon Sep 17 00:00:00 2001 From: Guillaume Knispel Date: Tue, 9 Dec 2008 15:28:34 +0100 Subject: powerpc: Fix corruption error in rh_alloc_fixed() There is an error in rh_alloc_fixed() of the Remote Heap code: If there is at least one free block blk won't be NULL at the end of the search loop, so -ENOMEM won't be returned and the else branch of "if (bs == s || be == e)" will be taken, corrupting the management structures. Signed-off-by: Guillaume Knispel Acked-by: Timur Tabi Signed-off-by: Kumar Gala --- arch/powerpc/lib/rheap.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/powerpc/lib/rheap.c b/arch/powerpc/lib/rheap.c index 29b2941..45907c1 100644 --- a/arch/powerpc/lib/rheap.c +++ b/arch/powerpc/lib/rheap.c @@ -556,6 +556,7 @@ unsigned long rh_alloc_fixed(rh_info_t * info, unsigned long start, int size, co be = blk->start + blk->size; if (s >= bs && e <= be) break; + blk = NULL; } if (blk == NULL) -- cgit v1.1 From 55aab5f49e384a361668d112eefdb33e90779af9 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Wed, 17 Dec 2008 12:52:34 -0700 Subject: x86 gart: don't complain if no AMD GART found Impact: remove annoying bootup printk It's perfectly normal for no AMD GART to be present, e.g., if you have Intel CPUs. None of the other iommu_init() functions makes noise when it finds nothing. Signed-off-by: Bjorn Helgaas Acked-by: Joerg Roedel Signed-off-by: Ingo Molnar --- arch/x86/kernel/pci-gart_64.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/pci-gart_64.c b/arch/x86/kernel/pci-gart_64.c index ba7ad83..a35eaa3 100644 --- a/arch/x86/kernel/pci-gart_64.c +++ b/arch/x86/kernel/pci-gart_64.c @@ -745,10 +745,8 @@ void __init gart_iommu_init(void) unsigned long scratch; long i; - if (cache_k8_northbridges() < 0 || num_k8_northbridges == 0) { - printk(KERN_INFO "PCI-GART: No AMD GART found.\n"); + if (cache_k8_northbridges() < 0 || num_k8_northbridges == 0) return; - } #ifndef CONFIG_AGP_AMD64 no_agp = 1; -- cgit v1.1 From de13d28e0cb4923600e618641063b3c54961a474 Mon Sep 17 00:00:00 2001 From: Haavard Skinnemoen Date: Thu, 18 Dec 2008 16:13:24 +0100 Subject: ATSTK1006: Fix boot from NAND flash Enable JFFS2 write buffer support so that the kernel can access a root filesystem in NAND flash. Signed-off-by: Haavard Skinnemoen --- arch/avr32/configs/atstk1006_defconfig | 134 ++++++++++++++++++++++++--------- 1 file changed, 97 insertions(+), 37 deletions(-) (limited to 'arch') diff --git a/arch/avr32/configs/atstk1006_defconfig b/arch/avr32/configs/atstk1006_defconfig index 8b6e54c..6c45a3b 100644 --- a/arch/avr32/configs/atstk1006_defconfig +++ b/arch/avr32/configs/atstk1006_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.27-rc1 -# Tue Aug 5 15:40:26 2008 +# Linux kernel version: 2.6.28-rc8 +# Thu Dec 18 11:22:23 2008 # CONFIG_AVR32=y CONFIG_GENERIC_GPIO=y @@ -67,6 +67,7 @@ CONFIG_SIGNALFD=y CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y +CONFIG_AIO=y CONFIG_VM_EVENT_COUNTERS=y CONFIG_SLUB_DEBUG=y # CONFIG_SLAB is not set @@ -77,15 +78,8 @@ CONFIG_PROFILING=y CONFIG_OPROFILE=m CONFIG_HAVE_OPROFILE=y CONFIG_KPROBES=y -# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set -# CONFIG_HAVE_IOREMAP_PROT is not set CONFIG_HAVE_KPROBES=y -# CONFIG_HAVE_KRETPROBES is not set -# CONFIG_HAVE_ARCH_TRACEHOOK is not set -# CONFIG_HAVE_DMA_ATTRS is not set -# CONFIG_USE_GENERIC_SMP_HELPERS is not set CONFIG_HAVE_CLK=y -CONFIG_PROC_PAGE_MONITOR=y # CONFIG_HAVE_GENERIC_DMA_COHERENT is not set CONFIG_SLABINFO=y CONFIG_RT_MUTEXES=y @@ -118,6 +112,7 @@ CONFIG_DEFAULT_CFQ=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="cfq" CONFIG_CLASSIC_RCU=y +CONFIG_FREEZER=y # # System Type and features @@ -134,6 +129,8 @@ CONFIG_CPU_AT32AP700X=y CONFIG_CPU_AT32AP7000=y CONFIG_BOARD_ATSTK1000=y # CONFIG_BOARD_ATNGW100 is not set +# CONFIG_BOARD_FAVR_32 is not set +# CONFIG_BOARD_MIMC200 is not set # CONFIG_BOARD_ATSTK1002 is not set # CONFIG_BOARD_ATSTK1003 is not set # CONFIG_BOARD_ATSTK1004 is not set @@ -171,14 +168,14 @@ CONFIG_FLATMEM_MANUAL=y # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y -# CONFIG_SPARSEMEM_STATIC is not set -# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_PAGEFLAGS_EXTENDED=y CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set +# CONFIG_PHYS_ADDR_T_64BIT is not set CONFIG_ZONE_DMA_FLAG=0 CONFIG_NR_QUICK=2 CONFIG_VIRT_TO_BUS=y +CONFIG_UNEVICTABLE_LRU=y # CONFIG_OWNERSHIP_TRACE is not set CONFIG_NMI_DEBUGGING=y # CONFIG_HZ_100 is not set @@ -186,7 +183,7 @@ CONFIG_HZ_250=y # CONFIG_HZ_300 is not set # CONFIG_HZ_1000 is not set CONFIG_HZ=250 -# CONFIG_SCHED_HRTICK is not set +CONFIG_SCHED_HRTICK=y CONFIG_CMDLINE="" # @@ -228,6 +225,8 @@ CONFIG_CPU_FREQ_AT32AP=y # Executable file formats # CONFIG_BINFMT_ELF=y +CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y +# CONFIG_HAVE_AOUT is not set # CONFIG_BINFMT_MISC is not set CONFIG_NET=y @@ -299,6 +298,7 @@ CONFIG_IPV6_TUNNEL=m # CONFIG_ATM is not set CONFIG_STP=m CONFIG_BRIDGE=m +# CONFIG_NET_DSA is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set CONFIG_LLC=m @@ -321,14 +321,8 @@ CONFIG_LLC=m # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_AF_RXRPC is not set - -# -# Wireless -# -# CONFIG_CFG80211 is not set -# CONFIG_WIRELESS_EXT is not set -# CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -359,6 +353,7 @@ CONFIG_MTD_CMDLINE_PARTS=y # User Modules And Translation Layers # CONFIG_MTD_CHAR=y +CONFIG_HAVE_MTD_OTP=y CONFIG_MTD_BLKDEVS=y CONFIG_MTD_BLOCK=y # CONFIG_FTL is not set @@ -407,6 +402,8 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=2 # Self-contained MTD device drivers # CONFIG_MTD_DATAFLASH=m +# CONFIG_MTD_DATAFLASH_WRITE_VERIFY is not set +CONFIG_MTD_DATAFLASH_OTP=y CONFIG_MTD_M25P80=m CONFIG_M25PXX_USE_FAST_READ=y # CONFIG_MTD_SLRAM is not set @@ -464,9 +461,10 @@ CONFIG_ATMEL_TCLIB=y CONFIG_ATMEL_TCB_CLKSRC=y CONFIG_ATMEL_TCB_CLKSRC_BLOCK=0 # CONFIG_EEPROM_93CX6 is not set +# CONFIG_ICS932S401 is not set CONFIG_ATMEL_SSC=m # CONFIG_ENCLOSURE_SERVICES is not set -# CONFIG_HAVE_IDE is not set +# CONFIG_C2PORT is not set # # SCSI device support @@ -548,6 +546,9 @@ CONFIG_MACB=y # CONFIG_IBM_NEW_EMAC_RGMII is not set # CONFIG_IBM_NEW_EMAC_TAH is not set # CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set # CONFIG_B44 is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -653,6 +654,7 @@ CONFIG_UNIX98_PTYS=y CONFIG_I2C=m CONFIG_I2C_BOARDINFO=y CONFIG_I2C_CHARDEV=m +CONFIG_I2C_HELPER_AUTO=y CONFIG_I2C_ALGOBIT=m # @@ -717,6 +719,10 @@ CONFIG_GPIOLIB=y CONFIG_GPIO_SYSFS=y # +# Memory mapped GPIO expanders: +# + +# # I2C GPIO expanders: # # CONFIG_GPIO_MAX732X is not set @@ -745,11 +751,11 @@ CONFIG_WATCHDOG=y # # CONFIG_SOFT_WATCHDOG is not set CONFIG_AT32AP700X_WDT=y +CONFIG_SSB_POSSIBLE=y # # Sonics Silicon Backplane # -CONFIG_SSB_POSSIBLE=y # CONFIG_SSB is not set # @@ -758,6 +764,10 @@ CONFIG_SSB_POSSIBLE=y # CONFIG_MFD_CORE is not set # CONFIG_MFD_SM501 is not set # CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_REGULATOR is not set # # Multimedia devices @@ -783,6 +793,7 @@ CONFIG_SSB_POSSIBLE=y CONFIG_FB=y # CONFIG_FIRMWARE_EDID is not set # CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y @@ -804,10 +815,13 @@ CONFIG_FB_CFB_IMAGEBLIT=y # CONFIG_FB_S1D13XXX is not set CONFIG_FB_ATMEL=y # CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_LCD_CLASS_DEVICE=y CONFIG_LCD_LTV350QV=y # CONFIG_LCD_ILI9320 is not set +# CONFIG_LCD_TDO24M is not set # CONFIG_LCD_VGG2432A4 is not set # CONFIG_LCD_PLATFORM is not set # CONFIG_BACKLIGHT_CLASS_DEVICE is not set @@ -818,6 +832,7 @@ CONFIG_LCD_LTV350QV=y # CONFIG_DISPLAY_SUPPORT is not set # CONFIG_LOGO is not set CONFIG_SOUND=m +CONFIG_SOUND_OSS_CORE=y CONFIG_SND=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m @@ -848,28 +863,32 @@ CONFIG_USB_SUPPORT=y # CONFIG_USB_ARCH_HAS_EHCI is not set # CONFIG_USB_OTG_WHITELIST is not set # CONFIG_USB_OTG_BLACKLIST_HUB is not set +# CONFIG_USB_MUSB_HDRC is not set +# CONFIG_USB_GADGET_MUSB_HDRC is not set # -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed; # CONFIG_USB_GADGET=y # CONFIG_USB_GADGET_DEBUG is not set # CONFIG_USB_GADGET_DEBUG_FILES is not set # CONFIG_USB_GADGET_DEBUG_FS is not set +CONFIG_USB_GADGET_VBUS_DRAW=2 CONFIG_USB_GADGET_SELECTED=y -# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_AT91 is not set CONFIG_USB_GADGET_ATMEL_USBA=y CONFIG_USB_ATMEL_USBA=y # CONFIG_USB_GADGET_FSL_USB2 is not set -# CONFIG_USB_GADGET_NET2280 is not set -# CONFIG_USB_GADGET_PXA25X is not set -# CONFIG_USB_GADGET_M66592 is not set -# CONFIG_USB_GADGET_PXA27X is not set -# CONFIG_USB_GADGET_GOKU is not set # CONFIG_USB_GADGET_LH7A40X is not set # CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_PXA25X is not set +# CONFIG_USB_GADGET_PXA27X is not set # CONFIG_USB_GADGET_S3C2410 is not set -# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_FSL_QE is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_GOKU is not set # CONFIG_USB_GADGET_DUMMY_HCD is not set CONFIG_USB_GADGET_DUALSPEED=y CONFIG_USB_ZERO=m @@ -887,7 +906,7 @@ CONFIG_MMC=y # CONFIG_MMC_UNSAFE_RESUME is not set # -# MMC/SD Card Drivers +# MMC/SD/SDIO Card Drivers # CONFIG_MMC_BLOCK=y CONFIG_MMC_BLOCK_BOUNCE=y @@ -895,10 +914,11 @@ CONFIG_MMC_BLOCK_BOUNCE=y # CONFIG_MMC_TEST is not set # -# MMC/SD Host Controller Drivers +# MMC/SD/SDIO Host Controller Drivers # # CONFIG_MMC_SDHCI is not set CONFIG_MMC_ATMELMCI=y +# CONFIG_MMC_ATMELMCI_DMA is not set CONFIG_MMC_SPI=m # CONFIG_MEMSTICK is not set CONFIG_NEW_LEDS=y @@ -918,6 +938,7 @@ CONFIG_LEDS_GPIO=m CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=m CONFIG_LEDS_TRIGGER_HEARTBEAT=m +# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set CONFIG_LEDS_TRIGGER_DEFAULT_ON=m # CONFIG_ACCESSIBILITY is not set CONFIG_RTC_LIB=y @@ -950,25 +971,31 @@ CONFIG_RTC_INTF_DEV=y # CONFIG_RTC_DRV_M41T80 is not set # CONFIG_RTC_DRV_S35390A is not set # CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set # # SPI RTC drivers # # CONFIG_RTC_DRV_M41T94 is not set # CONFIG_RTC_DRV_DS1305 is not set +# CONFIG_RTC_DRV_DS1390 is not set # CONFIG_RTC_DRV_MAX6902 is not set # CONFIG_RTC_DRV_R9701 is not set # CONFIG_RTC_DRV_RS5C348 is not set +# CONFIG_RTC_DRV_DS3234 is not set # # Platform RTC drivers # +# CONFIG_RTC_DRV_DS1286 is not set # CONFIG_RTC_DRV_DS1511 is not set # CONFIG_RTC_DRV_DS1553 is not set # CONFIG_RTC_DRV_DS1742 is not set # CONFIG_RTC_DRV_STK17TA8 is not set # CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set # CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_BQ4802 is not set # CONFIG_RTC_DRV_V3020 is not set # @@ -989,6 +1016,8 @@ CONFIG_DMA_ENGINE=y # CONFIG_NET_DMA is not set CONFIG_DMATEST=m # CONFIG_UIO is not set +# CONFIG_STAGING is not set +CONFIG_STAGING_EXCLUDE_BUILD=y # # File systems @@ -998,12 +1027,17 @@ CONFIG_EXT2_FS=m # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=m # CONFIG_EXT3_FS_XATTR is not set -# CONFIG_EXT4DEV_FS is not set +CONFIG_EXT4_FS=m +CONFIG_EXT4DEV_COMPAT=y +# CONFIG_EXT4_FS_XATTR is not set CONFIG_JBD=m # CONFIG_JBD_DEBUG is not set +CONFIG_JBD2=m +# CONFIG_JBD2_DEBUG is not set # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set # CONFIG_FS_POSIX_ACL is not set +CONFIG_FILE_LOCKING=y # CONFIG_XFS_FS is not set # CONFIG_OCFS2_FS is not set # CONFIG_DNOTIFY is not set @@ -1036,6 +1070,7 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set @@ -1054,7 +1089,8 @@ CONFIG_TMPFS=y # CONFIG_EFS_FS is not set CONFIG_JFFS2_FS=y CONFIG_JFFS2_FS_DEBUG=0 -# CONFIG_JFFS2_FS_WRITEBUFFER is not set +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set # CONFIG_JFFS2_SUMMARY is not set # CONFIG_JFFS2_FS_XATTR is not set # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set @@ -1088,6 +1124,7 @@ CONFIG_LOCKD=y CONFIG_LOCKD_V4=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y +# CONFIG_SUNRPC_REGISTER_V4 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set @@ -1185,10 +1222,21 @@ CONFIG_DEBUG_BUGVERBOSE=y CONFIG_FRAME_POINTER=y # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_KPROBES_SANITY_TEST is not set # CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set # CONFIG_LKDTM is not set # CONFIG_FAULT_INJECTION is not set + +# +# Tracers +# +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_BOOT_TRACER is not set +# CONFIG_DYNAMIC_PRINTK_DEBUG is not set # CONFIG_SAMPLES is not set # @@ -1196,17 +1244,26 @@ CONFIG_FRAME_POINTER=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set # CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y # # Crypto core or helper # +CONFIG_CRYPTO_FIPS=y CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_ALGAPI2=y CONFIG_CRYPTO_AEAD=m +CONFIG_CRYPTO_AEAD2=y CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_BLKCIPHER2=y CONFIG_CRYPTO_HASH=m +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_RNG=m +CONFIG_CRYPTO_RNG2=y CONFIG_CRYPTO_MANAGER=m +CONFIG_CRYPTO_MANAGER2=y # CONFIG_CRYPTO_GF128MUL is not set # CONFIG_CRYPTO_NULL is not set # CONFIG_CRYPTO_CRYPTD is not set @@ -1257,7 +1314,7 @@ CONFIG_CRYPTO_SHA1=m # # Ciphers # -# CONFIG_CRYPTO_AES is not set +CONFIG_CRYPTO_AES=m # CONFIG_CRYPTO_ANUBIS is not set # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_BLOWFISH is not set @@ -1278,14 +1335,17 @@ CONFIG_CRYPTO_DES=m # CONFIG_CRYPTO_DEFLATE=y CONFIG_CRYPTO_LZO=y + +# +# Random Number Generation +# +CONFIG_CRYPTO_ANSI_CPRNG=m # CONFIG_CRYPTO_HW is not set # # Library routines # CONFIG_BITREVERSE=y -# CONFIG_GENERIC_FIND_FIRST_BIT is not set -# CONFIG_GENERIC_FIND_NEXT_BIT is not set CONFIG_CRC_CCITT=m CONFIG_CRC16=y CONFIG_CRC_T10DIF=m -- cgit v1.1 From 8983fdb50878ae6fa2ced336ef6072f8d5d502e3 Mon Sep 17 00:00:00 2001 From: Haavard Skinnemoen Date: Thu, 18 Dec 2008 16:20:47 +0100 Subject: avr32: favr-32 build fix The favr-32 board code still refers to the old asm/arch header files which were moved to mach/ some time ago. Signed-off-by: Haavard Skinnemoen --- arch/avr32/boards/favr-32/flash.c | 2 +- arch/avr32/boards/favr-32/setup.c | 8 ++++---- 2 files changed, 5 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/avr32/boards/favr-32/flash.c b/arch/avr32/boards/favr-32/flash.c index 5f139b7..604bbd5 100644 --- a/arch/avr32/boards/favr-32/flash.c +++ b/arch/avr32/boards/favr-32/flash.c @@ -13,7 +13,7 @@ #include #include -#include +#include static struct smc_timing flash_timing __initdata = { .ncs_read_setup = 0, diff --git a/arch/avr32/boards/favr-32/setup.c b/arch/avr32/boards/favr-32/setup.c index 7538f3d..1ee4faf 100644 --- a/arch/avr32/boards/favr-32/setup.c +++ b/arch/avr32/boards/favr-32/setup.c @@ -25,10 +25,10 @@ #include -#include -#include -#include -#include +#include +#include +#include +#include /* Oscillator frequencies. These are board-specific */ unsigned long at32_board_osc_rates[3] = { -- cgit v1.1 From b909895739427874c089bc0e03dc119f99cab2dd Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Fri, 19 Dec 2008 13:48:34 -0800 Subject: sparseirq: fix numa_migrate_irq_desc dependency and comments Impact: reduce kconfig variable scope and clean up Bartlomiej pointed out that the config dependencies and comments are not right. update it depend to NUMA, and fix some comments Reported-by: Bartlomiej Zolnierkiewicz Signed-off-by: Yinghai Lu Signed-off-by: Ingo Molnar --- arch/x86/Kconfig | 2 +- arch/x86/kernel/io_apic.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 60a0088..5c24382 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -250,7 +250,7 @@ config SPARSE_IRQ config NUMA_MIGRATE_IRQ_DESC bool "Move irq desc when changing irq smp_affinity" - depends on SPARSE_IRQ && SMP + depends on SPARSE_IRQ && NUMA default n help This enables moving irq_desc to cpu/node that irq will use handled. diff --git a/arch/x86/kernel/io_apic.c b/arch/x86/kernel/io_apic.c index bfe1245..a74887b 100644 --- a/arch/x86/kernel/io_apic.c +++ b/arch/x86/kernel/io_apic.c @@ -2471,7 +2471,7 @@ static void irq_complete_move(struct irq_desc **descp) if (likely(!cfg->move_desc_pending)) return; - /* domain is not change, but affinity is changed */ + /* domain has not changed, but affinity did */ me = smp_processor_id(); if (cpu_isset(me, desc->affinity)) { *descp = desc = move_irq_desc(desc, me); -- cgit v1.1 From 280a9ca5d0663b185ddc4443052076c29652a328 Mon Sep 17 00:00:00 2001 From: Dmitry Adamushko Date: Sat, 20 Dec 2008 00:15:24 +0100 Subject: x86: fix resume (S2R) broken by Intel microcode module, on A110L Impact: fix deadlock This is in response to the following bug report: Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=12100 Subject : resume (S2R) broken by Intel microcode module, on A110L Submitter : Andreas Mohr Date : 2008-11-25 08:48 (19 days old) Handled-By : Dmitry Adamushko [ The deadlock scenario has been discovered by Andreas Mohr ] I think I might have a logical explanation why the system: (http://bugzilla.kernel.org/show_bug.cgi?id=12100) might hang upon resuming, OTOH it should have likely hanged each and every time. (1) possible deadlock in microcode_resume_cpu() if either 'if' section is taken; (2) now, I don't see it in spec. and can't experimentally verify it (newer ucodes don't seem to be available for my Core2duo)... but logically-wise, I'd think that when read upon resuming, the 'microcode revision' (MSR 0x8B) should be back to its original one (we need to reload ucode anyway so it doesn't seem logical if a cpu doesn't drop the version)... if so, the comparison with memcmp() for the full 'struct cpu_signature' is wrong... and that's how one of the aforementioned 'if' sections might have been triggered - leading to a deadlock. Obviously, in my tests I simulated loading/resuming with the ucode of the same version (just to see that the file is loaded/re-loaded upon resuming) so this issue has never popped up. I'd appreciate if someone with an appropriate system might give a try to the 2nd patch (titled "fix a comparison && deadlock..."). In any case, the deadlock situation is a must-have fix. Reported-by: Andreas Mohr Signed-off-by: Dmitry Adamushko Tested-by: Andreas Mohr Signed-off-by: Ingo Molnar Cc: Signed-off-by: Ingo Molnar --- arch/x86/kernel/microcode_core.c | 19 ++++++++++++++----- arch/x86/kernel/microcode_intel.c | 6 ++++++ 2 files changed, 20 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/x86/kernel/microcode_core.c b/arch/x86/kernel/microcode_core.c index 82fb280..c4b5b24 100644 --- a/arch/x86/kernel/microcode_core.c +++ b/arch/x86/kernel/microcode_core.c @@ -272,13 +272,18 @@ static struct attribute_group mc_attr_group = { .name = "microcode", }; -static void microcode_fini_cpu(int cpu) +static void __microcode_fini_cpu(int cpu) { struct ucode_cpu_info *uci = ucode_cpu_info + cpu; - mutex_lock(µcode_mutex); microcode_ops->microcode_fini_cpu(cpu); uci->valid = 0; +} + +static void microcode_fini_cpu(int cpu) +{ + mutex_lock(µcode_mutex); + __microcode_fini_cpu(cpu); mutex_unlock(µcode_mutex); } @@ -306,12 +311,16 @@ static int microcode_resume_cpu(int cpu) * to this cpu (a bit of paranoia): */ if (microcode_ops->collect_cpu_info(cpu, &nsig)) { - microcode_fini_cpu(cpu); + __microcode_fini_cpu(cpu); + printk(KERN_ERR "failed to collect_cpu_info for resuming cpu #%d\n", + cpu); return -1; } - if (memcmp(&nsig, &uci->cpu_sig, sizeof(nsig))) { - microcode_fini_cpu(cpu); + if ((nsig.sig != uci->cpu_sig.sig) || (nsig.pf != uci->cpu_sig.pf)) { + __microcode_fini_cpu(cpu); + printk(KERN_ERR "cached ucode doesn't match the resuming cpu #%d\n", + cpu); /* Should we look for a new ucode here? */ return 1; } diff --git a/arch/x86/kernel/microcode_intel.c b/arch/x86/kernel/microcode_intel.c index 622dc4a..a8e6279 100644 --- a/arch/x86/kernel/microcode_intel.c +++ b/arch/x86/kernel/microcode_intel.c @@ -155,6 +155,7 @@ static DEFINE_SPINLOCK(microcode_update_lock); static int collect_cpu_info(int cpu_num, struct cpu_signature *csig) { struct cpuinfo_x86 *c = &cpu_data(cpu_num); + unsigned long flags; unsigned int val[2]; memset(csig, 0, sizeof(*csig)); @@ -174,11 +175,16 @@ static int collect_cpu_info(int cpu_num, struct cpu_signature *csig) csig->pf = 1 << ((val[1] >> 18) & 7); } + /* serialize access to the physical write to MSR 0x79 */ + spin_lock_irqsave(µcode_update_lock, flags); + wrmsr(MSR_IA32_UCODE_REV, 0, 0); /* see notes above for revision 1.07. Apparent chip bug */ sync_core(); /* get the current revision from MSR 0x8B */ rdmsr(MSR_IA32_UCODE_REV, val[0], csig->rev); + spin_unlock_irqrestore(µcode_update_lock, flags); + pr_debug("microcode: collect_cpu_info : sig=0x%x, pf=0x%x, rev=0x%x\n", csig->sig, csig->pf, csig->rev); -- cgit v1.1 From 08d9d1c4d44ce43856da048cb0737ef769b61e9a Mon Sep 17 00:00:00 2001 From: David Daney Date: Wed, 17 Dec 2008 18:19:18 -0800 Subject: MIPS: Fix preprocessor warnings flaged by GCC 4.4 Signed-off-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/include/asm/elf.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/mips/include/asm/elf.h b/arch/mips/include/asm/elf.h index a8eac16..d58f128 100644 --- a/arch/mips/include/asm/elf.h +++ b/arch/mips/include/asm/elf.h @@ -232,7 +232,7 @@ typedef elf_fpreg_t elf_fpregset_t[ELF_NFPREG]; */ #ifdef __MIPSEB__ #define ELF_DATA ELFDATA2MSB -#elif __MIPSEL__ +#elif defined(__MIPSEL__) #define ELF_DATA ELFDATA2LSB #endif #define ELF_ARCH EM_MIPS -- cgit v1.1 From ed2b03ed3cec2a4719d04ef208319f9de6a4258a Mon Sep 17 00:00:00 2001 From: David Daney Date: Wed, 17 Dec 2008 13:28:39 -0800 Subject: MIPS: MIPS64R2: Fix buggy __arch_swab64 The way the code is written it was assuming dshd has the function of a hypothetical dshw instruction ... Signed-off-by: David Daney Signed-off-by: Ralf Baechle --- arch/mips/include/asm/byteorder.h | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/mips/include/asm/byteorder.h b/arch/mips/include/asm/byteorder.h index 2988d29..33790b9 100644 --- a/arch/mips/include/asm/byteorder.h +++ b/arch/mips/include/asm/byteorder.h @@ -50,9 +50,8 @@ static inline __attribute_const__ __u32 __arch_swab32(__u32 x) static inline __attribute_const__ __u64 __arch_swab64(__u64 x) { __asm__( - " dsbh %0, %1 \n" - " dshd %0, %0 \n" - " drotr %0, %0, 32 \n" + " dsbh %0, %1\n" + " dshd %0, %0" : "=r" (x) : "r" (x)); -- cgit v1.1 From 5289f46b9de04bde181d833d48df9671b69c4b08 Mon Sep 17 00:00:00 2001 From: Kyle McMartin Date: Tue, 23 Dec 2008 08:44:30 -0500 Subject: parisc: disable UP-optimized flush_tlb_mm flush_tlb_mm's "optimized" uniprocessor case of allocating a new context for userspace is exposing a race where we can suddely return to a syscall with the protection id and space id out of sync, trapping on the next userspace access. Debugged-by: James Bottomley Tested-by: Helge Deller Signed-off-by: Kyle McMartin Signed-off-by: Linus Torvalds --- arch/parisc/include/asm/tlbflush.h | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/parisc/include/asm/tlbflush.h b/arch/parisc/include/asm/tlbflush.h index b72ec66..1f6fd4f 100644 --- a/arch/parisc/include/asm/tlbflush.h +++ b/arch/parisc/include/asm/tlbflush.h @@ -44,9 +44,12 @@ static inline void flush_tlb_mm(struct mm_struct *mm) { BUG_ON(mm == &init_mm); /* Should never happen */ -#ifdef CONFIG_SMP +#if 1 || defined(CONFIG_SMP) flush_tlb_all(); #else + /* FIXME: currently broken, causing space id and protection ids + * to go out of sync, resulting in faults on userspace accesses. + */ if (mm) { if (mm->context != 0) free_sid(mm->context); -- cgit v1.1 From 40f15ad8aadff5ebb621b17a6f303ad2cd3f847d Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Wed, 24 Dec 2008 10:49:51 +0100 Subject: x86: disable X86_PTRACE_BTS there's a new ptrace arch level feature in .28: config X86_PTRACE_BTS bool "Branch Trace Store" it has broken fork() handling: the old DS area gets copied over into a new task without clearing it. Fixes exist but they came too late: c5dee61: x86, bts: memory accounting bf53de9: x86, bts: add fork and exit handling and are queued up for v2.6.29. This shows that the facility is still not tested well enough to release into a stable kernel - disable it for now and reactivate in .29. In .29 the hardware-branch-tracer will use the DS/BTS facilities too - hopefully resulting in better code. Signed-off-by: Ingo Molnar --- arch/x86/Kconfig.cpu | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/x86/Kconfig.cpu b/arch/x86/Kconfig.cpu index b815664..8e99073 100644 --- a/arch/x86/Kconfig.cpu +++ b/arch/x86/Kconfig.cpu @@ -520,6 +520,7 @@ config X86_PTRACE_BTS bool "Branch Trace Store" default y depends on X86_DEBUGCTLMSR + depends on BROKEN help This adds a ptrace interface to the hardware's branch trace store. -- cgit v1.1 From 4e17fee24a39448f3a20e9cf98887b7665825848 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Thu, 25 Dec 2008 12:04:17 +0100 Subject: x86: turn CONFIG_SPARSE_IRQ off by default New feature - lets disable it by default first - can flip it around later. Signed-off-by: Ingo Molnar --- arch/x86/Kconfig | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 5c24382..d14a880 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -241,7 +241,6 @@ config X86_HAS_BOOT_CPU_ID config SPARSE_IRQ bool "Support sparse irq numbering" depends on PCI_MSI || HT_IRQ - default y help This enables support for sparse irq, esp for msi/msi-x. You may need if you have lots of cards supports msi-x installed. -- cgit v1.1 From 973656fe1afb4adf95d7b9ab75d4660cd3821ea1 Mon Sep 17 00:00:00 2001 From: Ingo Molnar Date: Thu, 25 Dec 2008 16:26:47 +0100 Subject: x86, sparseirq: clean up Kconfig entry Impact: improve help text Signed-off-by: Ingo Molnar --- arch/x86/Kconfig | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index d14a880..e4c038a 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -242,10 +242,14 @@ config SPARSE_IRQ bool "Support sparse irq numbering" depends on PCI_MSI || HT_IRQ help - This enables support for sparse irq, esp for msi/msi-x. You may need - if you have lots of cards supports msi-x installed. + This enables support for sparse irqs. This is useful for distro + kernels that want to define a high CONFIG_NR_CPUS value but still + want to have low kernel memory footprint on smaller machines. - If you don't know what to do here, say Y. + ( Sparse IRQs can also be beneficial on NUMA boxes, as they spread + out the irq_desc[] array in a more NUMA-friendly way. ) + + If you don't know what to do here, say N. config NUMA_MIGRATE_IRQ_DESC bool "Move irq desc when changing irq smp_affinity" -- cgit v1.1