From 923dd2a46349bb1bb94aa894b7ff61093618d68a Mon Sep 17 00:00:00 2001 From: Jesper Nilsson Date: Wed, 5 Dec 2007 18:10:36 +0100 Subject: CRIS: Rearrange Kconfigs for v10 and v32 to allow compilation without warnings. - Remove some unneeded configs and add some new ones. - Merge common config items to common file instead of duplicating them. - Pull in standard Kconfig.preempt. - Remove some unneeded Kconfigs for subsystems not (yet) available on CRIS (md, scsi, ieee1394, i2o, isdn, telephony, media, pcmcia, pci) - Rename CRISv32 config items which had different types from CRISv10. (ETRAX_LED2G, ETRAX_LED2R, ETRAX_LED3G, ETRAX_LED3R, ETRAX_I2C_DATA_PORT, ETRAX_I2C_CLK_PORT) --- arch/cris/Kconfig | 483 +++++++++++++++++++++++++++++++++++++++++++++++++----- 1 file changed, 443 insertions(+), 40 deletions(-) (limited to 'arch/cris/Kconfig') diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig index 27b082a..0e9926d 100644 --- a/arch/cris/Kconfig +++ b/arch/cris/Kconfig @@ -13,10 +13,6 @@ config ZONE_DMA bool default y -config NO_DMA - bool - default y - config RWSEM_GENERIC_SPINLOCK bool default y @@ -24,6 +20,10 @@ config RWSEM_GENERIC_SPINLOCK config RWSEM_XCHGADD_ALGORITHM bool +config GENERIC_IOMAP + bool + default y + config ARCH_HAS_ILOG2_U32 bool default n @@ -44,13 +44,16 @@ config GENERIC_CALIBRATE_DELAY bool default y -config IRQ_PER_CPU - bool - default y - config NO_IOPORT def_bool y +config NO_IOMEM + def_bool y + +config FORCE_MAX_ZONEORDER + int + default 6 + config CRIS bool default y @@ -93,17 +96,15 @@ config ETRAX_FAST_TIMER timers). This is needed if CONFIG_ETRAX_SERIAL_FAST_TIMER is enabled. -config PREEMPT - bool "Preemptible Kernel" +config ETRAX_KMALLOCED_MODULES + bool "Enable module allocation with kmalloc" help - This option reduces the latency of the kernel when reacting to - real-time or interactive events by allowing a low priority process to - be preempted even if it is in kernel mode executing a system call. - This allows applications to run more reliably even when the system is - under load. + Enable module allocation with kmalloc instead of vmalloc. + +config OOM_REBOOT + bool "Enable reboot at out of memory" - Say Y here if you are building a kernel for a desktop, embedded - or real-time system. Say N if you are unsure. +source "kernel/Kconfig.preempt" source mm/Kconfig @@ -130,24 +131,124 @@ config SVINTO_SIM help Support the xsim ETRAX Simulator. +config ETRAXFS + bool "ETRAX-FS-V32" + help + Support CRIS V32. + +config CRIS_MACH_ARTPEC3 + bool "ARTPEC-3" + help + Support Axis ARTPEC-3. + endchoice +config ETRAX_VCS_SIM + bool "VCS Simulator" + help + Setup hardware to be run in the VCS simulator. + config ETRAX_ARCH_V10 bool default y if ETRAX100LX || ETRAX100LX_V2 default n if !(ETRAX100LX || ETRAX100LX_V2) +config ETRAX_ARCH_V32 + bool + default y if (ETRAXFS || CRIS_MACH_ARTPEC3) + default n if !(ETRAXFS || CRIS_MACH_ARTPEC3) + config ETRAX_DRAM_SIZE int "DRAM size (dec, in MB)" default "8" help Size of DRAM (decimal in MB) typically 2, 8 or 16. +config ETRAX_VMEM_SIZE + int "Video memory size (dec, in MB)" + depends on ETRAX_ARCH_V32 && !ETRAXFS + default 8 if !ETRAXFS + help + Size of Video accessible memory (decimal, in MB). + config ETRAX_FLASH_BUSWIDTH - int "Buswidth of flash in bytes" + int "Buswidth of NOR flash in bytes" default "2" help - Width in bytes of the Flash bus (1, 2 or 4). Is usually 2. + Width in bytes of the NOR Flash bus (1, 2 or 4). Is usually 2. + +config ETRAX_NANDFLASH_BUSWIDTH + int "Buswidth of NAND flash in bytes" + default "1" + help + Width in bytes of the NAND flash (1 or 2). + +config ETRAX_FLASH1_SIZE + int "FLASH1 size (dec, in MB. 0 = Unknown)" + default "0" + +choice + prompt "Product debug-port" + default ETRAX_DEBUG_PORT0 + +config ETRAX_DEBUG_PORT0 + bool "Serial-0" + help + Choose a serial port for the ETRAX debug console. Default to + port 0. + +config ETRAX_DEBUG_PORT1 + bool "Serial-1" + help + Use serial port 1 for the console. + +config ETRAX_DEBUG_PORT2 + bool "Serial-2" + help + Use serial port 2 for the console. + +config ETRAX_DEBUG_PORT3 + bool "Serial-3" + help + Use serial port 3 for the console. + +config ETRAX_DEBUG_PORT_NULL + bool "disabled" + help + Disable serial-port debugging. + +endchoice + +choice + prompt "Kernel GDB port" + depends on ETRAX_KGDB + default ETRAX_KGDB_PORT0 + help + Choose a serial port for kernel debugging. NOTE: This port should + not be enabled under Drivers for built-in interfaces (as it has its + own initialization code) and should not be the same as the debug port. + +config ETRAX_KGDB_PORT0 + bool "Serial-0" + help + Use serial port 0 for kernel debugging. + +config ETRAX_KGDB_PORT1 + bool "Serial-1" + help + Use serial port 1 for kernel debugging. + +config ETRAX_KGDB_PORT2 + bool "Serial-2" + help + Use serial port 2 for kernel debugging. + +config ETRAX_KGDB_PORT3 + bool "Serial-3" + help + Use serial port 3 for kernel debugging. + +endchoice source arch/cris/arch-v10/Kconfig source arch/cris/arch-v32/Kconfig @@ -161,6 +262,329 @@ menu "Drivers for built-in interfaces" source arch/cris/arch-v10/drivers/Kconfig source arch/cris/arch-v32/drivers/Kconfig +choice + prompt "RTC chip" + depends on ETRAX_RTC + default ETRAX_PCF8563 if ETRAX_ARCH_V32 + default ETRAX_DS1302 if ETRAX_ARCH_V10 + +config ETRAX_DS1302 + depends on ETRAX_ARCH_V10 + bool "DS1302" + help + Enables the driver for the DS1302 Real-Time Clock battery-backed + chip on some products. + +config ETRAX_PCF8563 + bool "PCF8563" + help + Enables the driver for the PCF8563 Real-Time Clock battery-backed + chip on some products. + +endchoice + +choice + prompt "Network LED behavior" + depends on ETRAX_ETHERNET + default ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY + +config ETRAX_NETWORK_LED_ON_WHEN_LINK + bool "LED_on_when_link" + help + Selecting LED_on_when_link will light the LED when there is a + connection and will flash off when there is activity. + + Selecting LED_on_when_activity will light the LED only when + there is activity. + + This setting will also affect the behaviour of other activity LEDs + e.g. Bluetooth. + +config ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY + bool "LED_on_when_activity" + help + Selecting LED_on_when_link will light the LED when there is a + connection and will flash off when there is activity. + + Selecting LED_on_when_activity will light the LED only when + there is activity. + + This setting will also affect the behaviour of other activity LEDs + e.g. Bluetooth. + +endchoice + +choice + prompt "Ser0 DMA out channel" + depends on ETRAX_SERIAL_PORT0 + default ETRAX_SERIAL_PORT0_DMA6_OUT if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT0_NO_DMA_OUT if ETRAX_ARCH_V10 + +config ETRAX_SERIAL_PORT0_NO_DMA_OUT + bool "Ser0 uses no DMA for output" + help + Do not use DMA for ser0 output. + +config ETRAX_SERIAL_PORT0_DMA6_OUT + bool "Ser0 uses DMA6 for output" + depends on ETRAXFS + help + Enables the DMA6 output channel for ser0 (ttyS0). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT0_DMA0_OUT + bool "Ser0 uses DMA0 for output" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA0 output channel for ser0 (ttyS0). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser0 DMA in channel " + depends on ETRAX_SERIAL_PORT0 + default ETRAX_SERIAL_PORT0_NO_DMA_IN if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT0_DMA7_IN if ETRAX_ARCH_V10 + help + What DMA channel to use for ser0. + +config ETRAX_SERIAL_PORT0_NO_DMA_IN + bool "Ser0 uses no DMA for input" + help + Do not use DMA for ser0 input. + +config ETRAX_SERIAL_PORT0_DMA7_IN + bool "Ser0 uses DMA7 for input" + depends on ETRAXFS + help + Enables the DMA7 input channel for ser0 (ttyS0). + If you do not enable DMA, an interrupt for each character will be + used when receiving data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT0_DMA1_IN + bool "Ser0 uses DMA1 for input" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA1 input channel for ser0 (ttyS0). + If you do not enable DMA, an interrupt for each character will be + used when receiveing data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser1 DMA in channel " + depends on ETRAX_SERIAL_PORT1 + default ETRAX_SERIAL_PORT1_NO_DMA_IN if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT1_DMA9_IN if ETRAX_ARCH_V10 + help + What DMA channel to use for ser1. + +config ETRAX_SERIAL_PORT1_NO_DMA_IN + bool "Ser1 uses no DMA for input" + help + Do not use DMA for ser1 input. + +config ETRAX_SERIAL_PORT1_DMA5_IN + bool "Ser1 uses DMA5 for input" + depends on ETRAX_ARCH_V32 + help + Enables the DMA5 input channel for ser1 (ttyS1). + If you do not enable DMA, an interrupt for each character will be + used when receiving data. + Normally you want this on, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT1_DMA9_IN + depends on ETRAX_ARCH_V10 + bool "Ser1 uses DMA9 for input" + +endchoice + + +choice + prompt "Ser1 DMA out channel" + depends on ETRAX_SERIAL_PORT1 + default ETRAX_SERIAL_PORT1_NO_DMA_OUT if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT1_DMA8_OUT if ETRAX_ARCH_V10 + help + What DMA channel to use for ser1. + +config ETRAX_SERIAL_PORT1_NO_DMA_OUT + bool "Ser1 uses no DMA for output" + help + Do not use DMA for ser1 output. + +config ETRAX_SERIAL_PORT1_DMA8_OUT + depends on ETRAX_ARCH_V10 + bool "Ser1 uses DMA8 for output" + +config ETRAX_SERIAL_PORT1_DMA4_OUT + depends on ETRAX_ARCH_V32 + bool "Ser1 uses DMA4 for output" + help + Enables the DMA4 output channel for ser1 (ttyS1). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want this on, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser2 DMA out channel" + depends on ETRAX_SERIAL_PORT2 + default ETRAX_SERIAL_PORT2_NO_DMA_OUT if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT2_DMA2_OUT if ETRAX_ARCH_V10 + +config ETRAX_SERIAL_PORT2_NO_DMA_OUT + bool "Ser2 uses no DMA for output" + help + Do not use DMA for ser2 output. + +config ETRAX_SERIAL_PORT2_DMA2_OUT + bool "Ser2 uses DMA2 for output" + depends on ETRAXFS || ETRAX_ARCH_V10 + help + Enables the DMA2 output channel for ser2 (ttyS2). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT2_DMA6_OUT + bool "Ser2 uses DMA6 for output" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA6 output channel for ser2 (ttyS2). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser2 DMA in channel" + depends on ETRAX_SERIAL_PORT2 + default ETRAX_SERIAL_PORT2_NO_DMA_IN if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT2_DMA3_IN if ETRAX_ARCH_V10 + help + What DMA channel to use for ser2. + +config ETRAX_SERIAL_PORT2_NO_DMA_IN + bool "Ser2 uses no DMA for input" + help + Do not use DMA for ser2 input. + +config ETRAX_SERIAL_PORT2_DMA3_IN + bool "Ser2 uses DMA3 for input" + depends on ETRAXFS || ETRAX_ARCH_V10 + help + Enables the DMA3 input channel for ser2 (ttyS2). + If you do not enable DMA, an interrupt for each character will be + used when receiving data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT2_DMA7_IN + bool "Ser2 uses DMA7 for input" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA7 input channel for ser2 (ttyS2). + If you do not enable DMA, an interrupt for each character will be + used when receiveing data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser3 DMA in channel" + depends on ETRAX_SERIAL_PORT3 + default ETRAX_SERIAL_PORT3_NO_DMA_IN if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT3_DMA5_IN if ETRAX_ARCH_V10 + help + What DMA channel to use for ser3. + +config ETRAX_SERIAL_PORT3_NO_DMA_IN + bool "Ser3 uses no DMA for input" + help + Do not use DMA for ser3 input. + +config ETRAX_SERIAL_PORT3_DMA5_IN + depends on ETRAX_ARCH_V10 + bool "DMA 5" + +config ETRAX_SERIAL_PORT3_DMA9_IN + bool "Ser3 uses DMA9 for input" + depends on ETRAXFS + help + Enables the DMA9 input channel for ser3 (ttyS3). + If you do not enable DMA, an interrupt for each character will be + used when receiving data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT3_DMA3_IN + bool "Ser3 uses DMA3 for input" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA3 input channel for ser3 (ttyS3). + If you do not enable DMA, an interrupt for each character will be + used when receiveing data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser3 DMA out channel" + depends on ETRAX_SERIAL_PORT3 + default ETRAX_SERIAL_PORT3_NO_DMA_OUT if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT3_DMA4_OUT if ETRAX_ARCH_V10 + +config ETRAX_SERIAL_PORT3_NO_DMA_OUT + bool "Ser3 uses no DMA for output" + help + Do not use DMA for ser3 output. + +config ETRAX_SERIAL_PORT3_DMA4_OUT + depends on ETRAX_ARCH_V10 + bool "DMA 4" + +config ETRAX_SERIAL_PORT3_DMA8_OUT + bool "Ser3 uses DMA8 for output" + depends on ETRAXFS + help + Enables the DMA8 output channel for ser3 (ttyS3). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT3_DMA2_OUT + bool "Ser3 uses DMA2 for output" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA2 output channel for ser3 (ttyS3). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + endmenu source "drivers/base/Kconfig" @@ -174,22 +598,10 @@ source "drivers/pnp/Kconfig" source "drivers/block/Kconfig" -source "drivers/md/Kconfig" - source "drivers/ide/Kconfig" -source "drivers/scsi/Kconfig" - -source "drivers/ieee1394/Kconfig" - -source "drivers/message/i2o/Kconfig" - source "drivers/net/Kconfig" -source "drivers/isdn/Kconfig" - -source "drivers/telephony/Kconfig" - source "drivers/i2c/Kconfig" source "drivers/rtc/Kconfig" @@ -201,17 +613,8 @@ source "drivers/input/Kconfig" source "drivers/char/Kconfig" -#source drivers/misc/Config.in -source "drivers/media/Kconfig" - source "fs/Kconfig" -source "sound/Kconfig" - -source "drivers/pcmcia/Kconfig" - -source "drivers/pci/Kconfig" - source "drivers/usb/Kconfig" source "arch/cris/Kconfig.debug" -- cgit v1.1 From 5062969d77fed23b8ffc1a4124e96e991adaf52c Mon Sep 17 00:00:00 2001 From: Jesper Nilsson Date: Mon, 21 Jan 2008 11:01:33 +0100 Subject: CRIS: Remove NO_IOMEM config, we have IO memory. --- arch/cris/Kconfig | 3 --- 1 file changed, 3 deletions(-) (limited to 'arch/cris/Kconfig') diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig index 0e9926d..dfddd33 100644 --- a/arch/cris/Kconfig +++ b/arch/cris/Kconfig @@ -47,9 +47,6 @@ config GENERIC_CALIBRATE_DELAY config NO_IOPORT def_bool y -config NO_IOMEM - def_bool y - config FORCE_MAX_ZONEORDER int default 6 -- cgit v1.1 From c3d6ddddb01e239c7176a561c499999636ab4f61 Mon Sep 17 00:00:00 2001 From: Jesper Nilsson Date: Mon, 21 Jan 2008 11:05:40 +0100 Subject: CRIS: Move common Kconfig variable ETRAX_RTC to arch independet Kconfig. --- arch/cris/Kconfig | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'arch/cris/Kconfig') diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig index dfddd33..4a27ef3 100644 --- a/arch/cris/Kconfig +++ b/arch/cris/Kconfig @@ -259,6 +259,18 @@ menu "Drivers for built-in interfaces" source arch/cris/arch-v10/drivers/Kconfig source arch/cris/arch-v32/drivers/Kconfig +config ETRAX_RTC + bool "Real Time Clock support" + depends on ETRAX_I2C + help + Enables drivers for the Real-Time Clock battery-backed chips on + some products. The kernel reads the time when booting, and + the date can be set using ioctl(fd, RTC_SET_TIME, &rt) with rt a + rtc_time struct (see ) on the /dev/rtc + device. You can check the time with cat /proc/rtc, but + normal time reading should be done using libc function time and + friends. + choice prompt "RTC chip" depends on ETRAX_RTC -- cgit v1.1 From c974a9e5a3c52f1c61501b22a0b0a278250a6bd1 Mon Sep 17 00:00:00 2001 From: Jesper Nilsson Date: Mon, 21 Jan 2008 11:44:11 +0100 Subject: CRIS v10: Add synchronous serial port driver for CRIS v10. --- arch/cris/Kconfig | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) (limited to 'arch/cris/Kconfig') diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig index 4a27ef3..e6d440a 100644 --- a/arch/cris/Kconfig +++ b/arch/cris/Kconfig @@ -292,6 +292,37 @@ config ETRAX_PCF8563 endchoice +config ETRAX_SYNCHRONOUS_SERIAL + bool "Synchronous serial-port support" + help + Select this to enable the synchronous serial port driver. + +config ETRAX_SYNCHRONOUS_SERIAL_PORT0 + bool "Synchronous serial port 0 enabled" + depends on ETRAX_SYNCHRONOUS_SERIAL + help + Enabled synchronous serial port 0. + +config ETRAX_SYNCHRONOUS_SERIAL0_DMA + bool "Enable DMA on synchronous serial port 0." + depends on ETRAX_SYNCHRONOUS_SERIAL_PORT0 + help + A synchronous serial port can run in manual or DMA mode. + Selecting this option will make it run in DMA mode. + +config ETRAX_SYNCHRONOUS_SERIAL_PORT1 + bool "Synchronous serial port 1 enabled" + depends on ETRAX_SYNCHRONOUS_SERIAL && (ETRAXFS || ETRAX_ARCH_V10) + help + Enabled synchronous serial port 1. + +config ETRAX_SYNCHRONOUS_SERIAL1_DMA + bool "Enable DMA on synchronous serial port 1." + depends on ETRAX_SYNCHRONOUS_SERIAL_PORT1 + help + A synchronous serial port can run in manual or DMA mode. + Selecting this option will make it run in DMA mode. + choice prompt "Network LED behavior" depends on ETRAX_ETHERNET -- cgit v1.1 From 79e04fdbb3423f6faa0d93e5ec41c2c2741d4052 Mon Sep 17 00:00:00 2001 From: Jesper Nilsson Date: Wed, 6 Feb 2008 13:21:28 +0100 Subject: CRIS: Move ETRAX_AXISFLASHMAP to common Kconfig file. --- arch/cris/Kconfig | 15 +++++++++++++++ 1 file changed, 15 insertions(+) (limited to 'arch/cris/Kconfig') diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig index e6d440a..90d8013 100644 --- a/arch/cris/Kconfig +++ b/arch/cris/Kconfig @@ -259,6 +259,21 @@ menu "Drivers for built-in interfaces" source arch/cris/arch-v10/drivers/Kconfig source arch/cris/arch-v32/drivers/Kconfig +config ETRAX_AXISFLASHMAP + bool "Axis flash-map support" + select MTD + select MTD_CFI + select MTD_CFI_AMDSTD + select MTD_JEDECPROBE if ETRAX_ARCH_V32 + select MTD_CHAR + select MTD_BLOCK + select MTD_PARTITIONS + select MTD_CONCAT + select MTD_COMPLEX_MAPPINGS + help + This option enables MTD mapping of flash devices. Needed to use + flash memories. If unsure, say Y. + config ETRAX_RTC bool "Real Time Clock support" depends on ETRAX_I2C -- cgit v1.1