From 254217d1a86f80981e6dfc54d7412931c6f6e80b Mon Sep 17 00:00:00 2001 From: Andrea Gelmini Date: Sun, 23 May 2010 21:56:41 +0200 Subject: USB: Documentation/usb/ehci.txt: Checkpatch cleanup Documentation/usb/ehci.txt:12: ERROR: trailing whitespace Signed-off-by: Andrea Gelmini Signed-off-by: Greg Kroah-Hartman --- Documentation/usb/ehci.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'Documentation') diff --git a/Documentation/usb/ehci.txt b/Documentation/usb/ehci.txt index 1536b7e..9dcafa7 100644 --- a/Documentation/usb/ehci.txt +++ b/Documentation/usb/ehci.txt @@ -9,7 +9,7 @@ compatible with the USB 1.1 standard. It defines three transfer speeds: - "Low Speed" 1.5 Mbit/sec USB 1.1 only addressed full speed and low speed. High speed devices -can be used on USB 1.1 systems, but they slow down to USB 1.1 speeds. +can be used on USB 1.1 systems, but they slow down to USB 1.1 speeds. USB 1.1 devices may also be used on USB 2.0 systems. When plugged into an EHCI controller, they are given to a USB 1.1 "companion" -- cgit v1.1 From b03dbffdcf7903ae3f1e2d61887462301752d060 Mon Sep 17 00:00:00 2001 From: Andrea Gelmini Date: Sun, 23 May 2010 21:56:42 +0200 Subject: USB: Documentation/usb/hotplug.txt: Checkpatch cleanup Documentation/usb/hotplug.txt:13: ERROR: trailing whitespace Documentation/usb/hotplug.txt:87: ERROR: trailing whitespace Signed-off-by: Andrea Gelmini Signed-off-by: Greg Kroah-Hartman --- Documentation/usb/hotplug.txt | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'Documentation') diff --git a/Documentation/usb/hotplug.txt b/Documentation/usb/hotplug.txt index f531706..4c94571 100644 --- a/Documentation/usb/hotplug.txt +++ b/Documentation/usb/hotplug.txt @@ -10,7 +10,7 @@ immediately usable. That means the system must do many things, including: - Bind a driver to that device. Bus frameworks do that using a device driver's probe() routine. - + - Tell other subsystems to configure the new device. Print queues may need to be enabled, networks brought up, disk partitions mounted, and so on. In some cases these will @@ -84,7 +84,7 @@ USB MODUTILS SUPPORT Current versions of module-init-tools will create a "modules.usbmap" file which contains the entries from each driver's MODULE_DEVICE_TABLE. Such files can be used by various user mode policy agents to make sure all the -right driver modules get loaded, either at boot time or later. +right driver modules get loaded, either at boot time or later. See for full information about such table entries; or look at existing drivers. Each table entry describes one or more criteria to -- cgit v1.1 From e9c64f2b39d6861d5f3108ec135966349fc66adb Mon Sep 17 00:00:00 2001 From: Andrea Gelmini Date: Sun, 23 May 2010 21:56:43 +0200 Subject: USB: Documentation/usb/linux.inf: Checkpatch cleanup Documentation/usb/linux.inf:66: ERROR: trailing whitespace Documentation/usb/linux.inf:67: ERROR: trailing whitespace Documentation/usb/linux.inf:98: ERROR: trailing whitespace Documentation/usb/linux.inf:99: ERROR: trailing whitespace Documentation/usb/linux.inf:115: ERROR: trailing whitespace Documentation/usb/linux.inf:116: ERROR: trailing whitespace Documentation/usb/linux.inf:120: ERROR: trailing whitespace Documentation/usb/linux.inf:121: ERROR: trailing whitespace Documentation/usb/linux.inf:122: ERROR: trailing whitespace Documentation/usb/linux.inf:123: ERROR: trailing whitespace Documentation/usb/linux.inf:144: ERROR: trailing whitespace Documentation/usb/linux.inf:145: ERROR: trailing whitespace Documentation/usb/linux.inf:146: ERROR: trailing whitespace Documentation/usb/linux.inf:147: ERROR: trailing whitespace Documentation/usb/linux.inf:158: ERROR: trailing whitespace Signed-off-by: Andrea Gelmini Signed-off-by: Greg Kroah-Hartman --- Documentation/usb/linux.inf | 30 +++++++++++++++--------------- 1 file changed, 15 insertions(+), 15 deletions(-) (limited to 'Documentation') diff --git a/Documentation/usb/linux.inf b/Documentation/usb/linux.inf index af71d87..ebd02be 100644 --- a/Documentation/usb/linux.inf +++ b/Documentation/usb/linux.inf @@ -63,8 +63,8 @@ HKR, Ndi, DeviceId, 0, "USB\VID_0525&PID_a4a2" CopyFiles=RNDIS_CopyFiles_98 [RNDIS_CopyFiles_98] -usb8023.sys, usb8023w.sys, , 0 -rndismp.sys, rndismpw.sys, , 0 +usb8023.sys, usb8023w.sys, , 0 +rndismp.sys, rndismpw.sys, , 0 ; Windows Millennium Edition specific sections -------------------- @@ -95,8 +95,8 @@ HKR, Ndi, DeviceId, 0, "USB\VID_0525&PID_a4a2" CopyFiles=RNDIS_CopyFiles_ME [RNDIS_CopyFiles_ME] -usb8023.sys, usb8023m.sys, , 0 -rndismp.sys, rndismpm.sys, , 0 +usb8023.sys, usb8023m.sys, , 0 +rndismp.sys, rndismpm.sys, , 0 ; Windows 2000 specific sections --------------------------------- @@ -112,15 +112,15 @@ AddService = USB_RNDIS, 2, RNDIS_ServiceInst_NT, RNDIS_EventLog [RNDIS_CopyFiles_NT] ; no rename of files on Windows 2000, use the 'k' names as is -usb8023k.sys, , , 0 -rndismpk.sys, , , 0 +usb8023k.sys, , , 0 +rndismpk.sys, , , 0 [RNDIS_ServiceInst_NT] DisplayName = %ServiceDisplayName% -ServiceType = 1 -StartType = 3 -ErrorControl = 1 -ServiceBinary = %12%\usb8023k.sys +ServiceType = 1 +StartType = 3 +ErrorControl = 1 +ServiceBinary = %12%\usb8023k.sys LoadOrderGroup = NDIS AddReg = RNDIS_WMI_AddReg_NT @@ -141,10 +141,10 @@ AddService = USB_RNDIS, 2, RNDIS_ServiceInst_51, RNDIS_EventLog [RNDIS_ServiceInst_51] DisplayName = %ServiceDisplayName% -ServiceType = 1 -StartType = 3 -ErrorControl = 1 -ServiceBinary = %12%\usb8023.sys +ServiceType = 1 +StartType = 3 +ErrorControl = 1 +ServiceBinary = %12%\usb8023.sys LoadOrderGroup = NDIS AddReg = RNDIS_WMI_AddReg_51 @@ -155,7 +155,7 @@ HKR, , MofImagePath, 0x00020000, "System32\drivers\rndismp.sys" [RNDIS_AddReg_NT] HKR, Ndi, Service, 0, "USB_RNDIS" -HKR, Ndi\Interfaces, UpperRange, 0, "ndis5" +HKR, Ndi\Interfaces, UpperRange, 0, "ndis5" HKR, Ndi\Interfaces, LowerRange, 0, "ethernet" [RNDIS_EventLog] -- cgit v1.1 From 90eef5b8acb459da65b269cf1db9f92debda1a24 Mon Sep 17 00:00:00 2001 From: Michal Nazarewicz Date: Mon, 21 Jun 2010 13:57:05 +0200 Subject: USB: gadget: g_ether: updated INF file Updated the INF file for the g_ether gadget. It should work with most recent Windows systems now. Signed-off-by: Michal Nazarewicz Signed-off-by: Kyungmin Park Signed-off-by: Greg Kroah-Hartman --- Documentation/usb/linux.inf | 228 +++++++++----------------------------------- 1 file changed, 47 insertions(+), 181 deletions(-) (limited to 'Documentation') diff --git a/Documentation/usb/linux.inf b/Documentation/usb/linux.inf index ebd02be..b9e538c 100644 --- a/Documentation/usb/linux.inf +++ b/Documentation/usb/linux.inf @@ -1,200 +1,66 @@ -; MS-Windows driver config matching some basic modes of the -; Linux-USB Ethernet/RNDIS gadget firmware: -; -; - RNDIS plus CDC Ethernet ... this may be familiar as a DOCSIS -; cable modem profile, and supports most non-Microsoft USB hosts -; -; - RNDIS plus CDC Subset ... used by hardware that incapable of -; full CDC Ethernet support. -; -; Microsoft only directly supports RNDIS drivers, and bundled them into XP. -; The Microsoft "Remote NDIS USB Driver Kit" is currently found at: -; http://www.microsoft.com/whdc/device/network/ndis/rmndis.mspx - +; Based on template INF file found at +; +; which was: +; Copyright (c) Microsoft Corporation +; and released under the MLPL as found at: +; . +; For use only on Windows operating systems. [Version] -Signature = "$CHICAGO$" +Signature = "$Windows NT$" Class = Net ClassGUID = {4d36e972-e325-11ce-bfc1-08002be10318} Provider = %Linux% -Compatible = 1 -MillenniumPreferred = .ME -DriverVer = 03/30/2004,0.0.0.0 -; catalog file would be used by WHQL -;CatalogFile = Linux.cat +DriverVer = 06/21/2006,6.0.6000.16384 [Manufacturer] -%Linux% = LinuxDevices,NT.5.1 +%Linux% = LinuxDevices,NTx86,NTamd64,NTia64 + +; Decoration for x86 architecture +[LinuxDevices.NTx86] +%LinuxDevice% = RNDIS.NT.5.1, USB\VID_0525&PID_a4a2 -[LinuxDevices] -; NetChip IDs, used by both firmware modes -%LinuxDevice% = RNDIS, USB\VID_0525&PID_a4a2 +; Decoration for x64 architecture +[LinuxDevices.NTamd64] +%LinuxDevice% = RNDIS.NT.5.1, USB\VID_0525&PID_a4a2 -[LinuxDevices.NT.5.1] -%LinuxDevice% = RNDIS.NT.5.1, USB\VID_0525&PID_a4a2 +; Decoration for ia64 architecture +[LinuxDevices.NTia64] +%LinuxDevice% = RNDIS.NT.5.1, USB\VID_0525&PID_a4a2 +;@@@ This is the common setting for setup [ControlFlags] ExcludeFromSelect=* -; Windows 98, Windows 98 Second Edition specific sections -------- - -[RNDIS] -DeviceID = usb8023 -MaxInstance = 512 -DriverVer = 03/30/2004,0.0.0.0 -AddReg = RNDIS_AddReg_98, RNDIS_AddReg_Common - -[RNDIS_AddReg_98] -HKR, , DevLoader, 0, *ndis -HKR, , DeviceVxDs, 0, usb8023.sys -HKR, NDIS, LogDriverName, 0, "usb8023" -HKR, NDIS, MajorNdisVersion, 1, 5 -HKR, NDIS, MinorNdisVersion, 1, 0 -HKR, Ndi\Interfaces, DefUpper, 0, "ndis3,ndis4,ndis5" -HKR, Ndi\Interfaces, DefLower, 0, "ethernet" -HKR, Ndi\Interfaces, UpperRange, 0, "ndis3,ndis4,ndis5" -HKR, Ndi\Interfaces, LowerRange, 0, "ethernet" -HKR, Ndi\Install, ndis3, 0, "RNDIS_Install_98" -HKR, Ndi\Install, ndis4, 0, "RNDIS_Install_98" -HKR, Ndi\Install, ndis5, 0, "RNDIS_Install_98" -HKR, Ndi, DeviceId, 0, "USB\VID_0525&PID_a4a2" - -[RNDIS_Install_98] -CopyFiles=RNDIS_CopyFiles_98 - -[RNDIS_CopyFiles_98] -usb8023.sys, usb8023w.sys, , 0 -rndismp.sys, rndismpw.sys, , 0 - -; Windows Millennium Edition specific sections -------------------- - -[RNDIS.ME] -DeviceID = usb8023 -MaxInstance = 512 -DriverVer = 03/30/2004,0.0.0.0 -AddReg = RNDIS_AddReg_ME, RNDIS_AddReg_Common -Characteristics = 0x84 ; NCF_PHYSICAL + NCF_HAS_UI -BusType = 15 - -[RNDIS_AddReg_ME] -HKR, , DevLoader, 0, *ndis -HKR, , DeviceVxDs, 0, usb8023.sys -HKR, NDIS, LogDriverName, 0, "usb8023" -HKR, NDIS, MajorNdisVersion, 1, 5 -HKR, NDIS, MinorNdisVersion, 1, 0 -HKR, Ndi\Interfaces, DefUpper, 0, "ndis3,ndis4,ndis5" -HKR, Ndi\Interfaces, DefLower, 0, "ethernet" -HKR, Ndi\Interfaces, UpperRange, 0, "ndis3,ndis4,ndis5" -HKR, Ndi\Interfaces, LowerRange, 0, "ethernet" -HKR, Ndi\Install, ndis3, 0, "RNDIS_Install_ME" -HKR, Ndi\Install, ndis4, 0, "RNDIS_Install_ME" -HKR, Ndi\Install, ndis5, 0, "RNDIS_Install_ME" -HKR, Ndi, DeviceId, 0, "USB\VID_0525&PID_a4a2" - -[RNDIS_Install_ME] -CopyFiles=RNDIS_CopyFiles_ME - -[RNDIS_CopyFiles_ME] -usb8023.sys, usb8023m.sys, , 0 -rndismp.sys, rndismpm.sys, , 0 - -; Windows 2000 specific sections --------------------------------- - -[RNDIS.NT] -Characteristics = 0x84 ; NCF_PHYSICAL + NCF_HAS_UI -BusType = 15 -DriverVer = 03/30/2004,0.0.0.0 -AddReg = RNDIS_AddReg_NT, RNDIS_AddReg_Common -CopyFiles = RNDIS_CopyFiles_NT - -[RNDIS.NT.Services] -AddService = USB_RNDIS, 2, RNDIS_ServiceInst_NT, RNDIS_EventLog - -[RNDIS_CopyFiles_NT] -; no rename of files on Windows 2000, use the 'k' names as is -usb8023k.sys, , , 0 -rndismpk.sys, , , 0 - -[RNDIS_ServiceInst_NT] -DisplayName = %ServiceDisplayName% -ServiceType = 1 -StartType = 3 -ErrorControl = 1 -ServiceBinary = %12%\usb8023k.sys -LoadOrderGroup = NDIS -AddReg = RNDIS_WMI_AddReg_NT - -[RNDIS_WMI_AddReg_NT] -HKR, , MofImagePath, 0x00020000, "System32\drivers\rndismpk.sys" - -; Windows XP specific sections ----------------------------------- - +; DDInstall section +; References the in-build Netrndis.inf [RNDIS.NT.5.1] -Characteristics = 0x84 ; NCF_PHYSICAL + NCF_HAS_UI -BusType = 15 -DriverVer = 03/30/2004,0.0.0.0 -AddReg = RNDIS_AddReg_NT, RNDIS_AddReg_Common -; no copyfiles - the files are already in place - +Characteristics = 0x84 ; NCF_PHYSICAL + NCF_HAS_UI +BusType = 15 +; NEVER REMOVE THE FOLLOWING REFERENCE FOR NETRNDIS.INF +include = netrndis.inf +needs = Usb_Rndis.ndi +AddReg = Rndis_AddReg_Vista + +; DDInstal.Services section [RNDIS.NT.5.1.Services] -AddService = USB_RNDIS, 2, RNDIS_ServiceInst_51, RNDIS_EventLog - -[RNDIS_ServiceInst_51] -DisplayName = %ServiceDisplayName% -ServiceType = 1 -StartType = 3 -ErrorControl = 1 -ServiceBinary = %12%\usb8023.sys -LoadOrderGroup = NDIS -AddReg = RNDIS_WMI_AddReg_51 - -[RNDIS_WMI_AddReg_51] -HKR, , MofImagePath, 0x00020000, "System32\drivers\rndismp.sys" - -; Windows 2000 and Windows XP common sections -------------------- - -[RNDIS_AddReg_NT] -HKR, Ndi, Service, 0, "USB_RNDIS" -HKR, Ndi\Interfaces, UpperRange, 0, "ndis5" -HKR, Ndi\Interfaces, LowerRange, 0, "ethernet" - -[RNDIS_EventLog] -AddReg = RNDIS_EventLog_AddReg - -[RNDIS_EventLog_AddReg] -HKR, , EventMessageFile, 0x00020000, "%%SystemRoot%%\System32\netevent.dll" -HKR, , TypesSupported, 0x00010001, 7 - -; Common Sections ------------------------------------------------- - -[RNDIS_AddReg_Common] -HKR, NDI\params\NetworkAddress, ParamDesc, 0, %NetworkAddress% -HKR, NDI\params\NetworkAddress, type, 0, "edit" -HKR, NDI\params\NetworkAddress, LimitText, 0, "12" -HKR, NDI\params\NetworkAddress, UpperCase, 0, "1" -HKR, NDI\params\NetworkAddress, default, 0, " " -HKR, NDI\params\NetworkAddress, optional, 0, "1" - -[SourceDisksNames] -1=%SourceDisk%,,1 - -[SourceDisksFiles] -usb8023m.sys=1 -rndismpm.sys=1 -usb8023w.sys=1 -rndismpw.sys=1 -usb8023k.sys=1 -rndismpk.sys=1 - -[DestinationDirs] -RNDIS_CopyFiles_98 = 10, system32/drivers -RNDIS_CopyFiles_ME = 10, system32/drivers -RNDIS_CopyFiles_NT = 12 +include = netrndis.inf +needs = Usb_Rndis.ndi.Services + +; Optional registry settings. You can modify as needed. +[RNDIS_AddReg_Vista] +HKR, NDI\params\VistaProperty, ParamDesc, 0, %Vista_Property% +HKR, NDI\params\VistaProperty, type, 0, "edit" +HKR, NDI\params\VistaProperty, LimitText, 0, "12" +HKR, NDI\params\VistaProperty, UpperCase, 0, "1" +HKR, NDI\params\VistaProperty, default, 0, " " +HKR, NDI\params\VistaProperty, optional, 0, "1" + +; No sys copyfiles - the sys files are already in-build +; (part of the operating system). +; We do not support XP SP1-, 2003 SP1-, ME, 9x. [Strings] -ServiceDisplayName = "USB Remote NDIS Network Device Driver" -NetworkAddress = "Network Address" Linux = "Linux Developer Community" LinuxDevice = "Linux USB Ethernet/RNDIS Gadget" -SourceDisk = "Ethernet/RNDIS Gadget Driver Install Disk" - +Vista_Property = "Optional Vista Property" -- cgit v1.1 From e41e134e34fbbfc7868f4784cd1370847462b879 Mon Sep 17 00:00:00 2001 From: Michal Nazarewicz Date: Mon, 21 Jun 2010 13:57:06 +0200 Subject: USB: gadget: g_serial: INF file updated Updated the INF file for g_serial gadget. It should work with most recent Windows systems now. Signed-off-by: Michal Nazarewicz Signed-off-by: Kyungmin Park Signed-off-by: Greg Kroah-Hartman --- Documentation/usb/gadget_serial.txt | 87 ++++------------------------- Documentation/usb/linux-cdc-acm.inf | 107 ++++++++++++++++++++++++++++++++++++ 2 files changed, 117 insertions(+), 77 deletions(-) create mode 100644 Documentation/usb/linux-cdc-acm.inf (limited to 'Documentation') diff --git a/Documentation/usb/gadget_serial.txt b/Documentation/usb/gadget_serial.txt index eac7df9..61e67f6 100644 --- a/Documentation/usb/gadget_serial.txt +++ b/Documentation/usb/gadget_serial.txt @@ -151,88 +151,23 @@ instructions below to install the host side driver. Installing the Windows Host ACM Driver -------------------------------------- -To use the Windows ACM driver you must have the files "gserial.inf" -and "usbser.sys" together in a folder on the Windows machine. - -The "gserial.inf" file is given here. - --------------------- CUT HERE -------------------- -[Version] -Signature="$Windows NT$" -Class=Ports -ClassGuid={4D36E978-E325-11CE-BFC1-08002BE10318} -Provider=%LINUX% -DriverVer=08/17/2004,0.0.2.0 -; Copyright (C) 2004 Al Borchers (alborchers@steinerpoint.com) - -[Manufacturer] -%LINUX%=GSerialDeviceList - -[GSerialDeviceList] -%GSERIAL%=GSerialInstall, USB\VID_0525&PID_A4A7 - -[DestinationDirs] -DefaultDestDir=10,System32\Drivers - -[GSerialInstall] -CopyFiles=GSerialCopyFiles -AddReg=GSerialAddReg - -[GSerialCopyFiles] -usbser.sys - -[GSerialAddReg] -HKR,,DevLoader,,*ntkern -HKR,,NTMPDriver,,usbser.sys -HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider" - -[GSerialInstall.Services] -AddService = usbser,0x0002,GSerialService - -[GSerialService] -DisplayName = %GSERIAL_DISPLAY_NAME% -ServiceType = 1 ; SERVICE_KERNEL_DRIVER -StartType = 3 ; SERVICE_DEMAND_START -ErrorControl = 1 ; SERVICE_ERROR_NORMAL -ServiceBinary = %10%\System32\Drivers\usbser.sys -LoadOrderGroup = Base - -[Strings] -LINUX = "Linux" -GSERIAL = "Gadget Serial" -GSERIAL_DISPLAY_NAME = "USB Gadget Serial Driver" --------------------- CUT HERE -------------------- - -The "usbser.sys" file comes with various versions of Windows. -For example, it can be found on Windows XP typically in - - C:\WINDOWS\Driver Cache\i386\driver.cab - -Or it can be found on the Windows 98SE CD in the "win98" folder -in the "DRIVER11.CAB" through "DRIVER20.CAB" cab files. You will -need the DOS "expand" program, the Cygwin "cabextract" program, or -a similar program to unpack these cab files and extract "usbser.sys". - -For example, to extract "usbser.sys" into the current directory -on Windows XP, open a DOS window and run a command like - - expand C:\WINDOWS\Driver~1\i386\driver.cab -F:usbser.sys . - -(Thanks to Nishant Kamat for pointing out this DOS command.) +To use the Windows ACM driver you must have the "linux-cdc-acm.inf" +file (provided along this document) which supports all recent versions +of Windows. When the gadget serial driver is loaded and the USB device connected to the Windows host with a USB cable, Windows should recognize the gadget serial device and ask for a driver. Tell Windows to find the -driver in the folder that contains "gserial.inf" and "usbser.sys". +driver in the folder that contains the "linux-cdc-acm.inf" file. For example, on Windows XP, when the gadget serial device is first plugged in, the "Found New Hardware Wizard" starts up. Select -"Install from a list or specific location (Advanced)", then on -the next screen select "Include this location in the search" and -enter the path or browse to the folder containing "gserial.inf" and -"usbser.sys". Windows will complain that the Gadget Serial driver -has not passed Windows Logo testing, but select "Continue anyway" -and finish the driver installation. +"Install from a list or specific location (Advanced)", then on the +next screen select "Include this location in the search" and enter the +path or browse to the folder containing the "linux-cdc-acm.inf" file. +Windows will complain that the Gadget Serial driver has not passed +Windows Logo testing, but select "Continue anyway" and finish the +driver installation. On Windows XP, in the "Device Manager" (under "Control Panel", "System", "Hardware") expand the "Ports (COM & LPT)" entry and you @@ -345,5 +280,3 @@ you should be able to send data back and forth between the gadget side and host side systems. Anything you type on the terminal window on the gadget side should appear in the terminal window on the host side and vice versa. - - diff --git a/Documentation/usb/linux-cdc-acm.inf b/Documentation/usb/linux-cdc-acm.inf new file mode 100644 index 0000000..14d2b87 --- /dev/null +++ b/Documentation/usb/linux-cdc-acm.inf @@ -0,0 +1,107 @@ +; Windows USB CDC ACM Setup File + +; Based on INF template which was: +; Copyright (c) 2000 Microsoft Corporation +; Copyright (c) 2007 Microchip Technology Inc. +; likely to be covered by the MLPL as found at: +; . +; For use only on Windows operating systems. + +[Version] +Signature="$Windows NT$" +Class=Ports +ClassGuid={4D36E978-E325-11CE-BFC1-08002BE10318} +Provider=%Linux% +DriverVer=11/15/2007,5.1.2600.0 + +[Manufacturer] +%Linux%=DeviceList, NTamd64 + +[DestinationDirs] +DefaultDestDir=12 + + +;------------------------------------------------------------------------------ +; Windows 2000/XP/Vista-32bit Sections +;------------------------------------------------------------------------------ + +[DriverInstall.nt] +include=mdmcpq.inf +CopyFiles=DriverCopyFiles.nt +AddReg=DriverInstall.nt.AddReg + +[DriverCopyFiles.nt] +usbser.sys,,,0x20 + +[DriverInstall.nt.AddReg] +HKR,,DevLoader,,*ntkern +HKR,,NTMPDriver,,USBSER.sys +HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider" + +[DriverInstall.nt.Services] +AddService=usbser, 0x00000002, DriverService.nt + +[DriverService.nt] +DisplayName=%SERVICE% +ServiceType=1 +StartType=3 +ErrorControl=1 +ServiceBinary=%12%\USBSER.sys + +;------------------------------------------------------------------------------ +; Vista-64bit Sections +;------------------------------------------------------------------------------ + +[DriverInstall.NTamd64] +include=mdmcpq.inf +CopyFiles=DriverCopyFiles.NTamd64 +AddReg=DriverInstall.NTamd64.AddReg + +[DriverCopyFiles.NTamd64] +USBSER.sys,,,0x20 + +[DriverInstall.NTamd64.AddReg] +HKR,,DevLoader,,*ntkern +HKR,,NTMPDriver,,USBSER.sys +HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider" + +[DriverInstall.NTamd64.Services] +AddService=usbser, 0x00000002, DriverService.NTamd64 + +[DriverService.NTamd64] +DisplayName=%SERVICE% +ServiceType=1 +StartType=3 +ErrorControl=1 +ServiceBinary=%12%\USBSER.sys + + +;------------------------------------------------------------------------------ +; Vendor and Product ID Definitions +;------------------------------------------------------------------------------ +; When developing your USB device, the VID and PID used in the PC side +; application program and the firmware on the microcontroller must match. +; Modify the below line to use your VID and PID. Use the format as shown +; below. +; Note: One INF file can be used for multiple devices with different +; VID and PIDs. For each supported device, append +; ",USB\VID_xxxx&PID_yyyy" to the end of the line. +;------------------------------------------------------------------------------ +[SourceDisksFiles] +[SourceDisksNames] +[DeviceList] +%DESCRIPTION%=DriverInstall, USB\VID_0525&PID_A4A7 + +[DeviceList.NTamd64] +%DESCRIPTION%=DriverInstall, USB\VID_0525&PID_A4A7 + + +;------------------------------------------------------------------------------ +; String Definitions +;------------------------------------------------------------------------------ +;Modify these strings to customize your device +;------------------------------------------------------------------------------ +[Strings] +Linux = "Linux Developer Community" +DESCRIPTION = "Gadget Serial" +SERVICE = "USB RS-232 Emulation Driver" -- cgit v1.1 From c7ba692294ef2f69a76b24b2ad45fc6c0ac0d497 Mon Sep 17 00:00:00 2001 From: Michal Nazarewicz Date: Mon, 21 Jun 2010 13:57:07 +0200 Subject: USB: gadget: g_multi: added documentation and INF files A short documentation of the g_multi driver along with INF files for Windows XP SP3 are provided. Signed-off-by: Michal Nazarewicz Signed-off-by: Kyungmin Park Signed-off-by: Greg Kroah-Hartman --- Documentation/usb/gadget_multi.txt | 150 ++++++++++++++++++++++++++++++++++++ Documentation/usb/linux-cdc-acm.inf | 4 +- Documentation/usb/linux.inf | 6 +- 3 files changed, 155 insertions(+), 5 deletions(-) create mode 100644 Documentation/usb/gadget_multi.txt (limited to 'Documentation') diff --git a/Documentation/usb/gadget_multi.txt b/Documentation/usb/gadget_multi.txt new file mode 100644 index 0000000..80f4ef0 --- /dev/null +++ b/Documentation/usb/gadget_multi.txt @@ -0,0 +1,150 @@ + -*- org -*- + +* Overview + +The Multifunction Composite Gadget (or g_multi) is a composite gadget +that makes extensive use of the composite framework to provide +a... multifunction gadget. + +In it's standard configuration it provides a single USB configuration +with RNDIS[1] (that is Ethernet), USB CDC[2] ACM (that is serial) and +USB Mass Storage functions. + +A CDC ECM (Ethernet) function may be turned on via a Kconfig option +and RNDIS can be turned off. If they are both enabled the gadget will +have two configurations -- one with RNDIS and another with CDC ECM[3]. + +Please not that if you use non-standard configuration (that is enable +CDC ECM) you may need to change vendor and/or product ID. + +* Host drivers + +To make use of the gadget one needs to make it work on host side -- +without that there's no hope of achieving anything with the gadget. +As one might expect, things one need to do very from system to system. + +** Linux host drivers + +Since the gadget uses standard composite framework and appears as such +to Linux host it does not need any additional drivers on Linux host +side. All the functions are handled by respective drivers developed +for them. + +This is also true for two configuration set-up with RNDIS +configuration being the first one. Linux host will use the second +configuration with CDC ECM which should work better under Linux. + +** Windows host drivers + +For the gadget two work under Windows two conditions have to be met: + +*** Detecting as composite gadget + +First of all, Windows need to detect the gadget as an USB composite +gadget which on its own have some conditions[4]. If they are met, +Windows lets USB Generic Parent Driver[5] handle the device which then +tries to much drivers for each individual interface (sort of, don't +get into too many details). + +The good news is: you do not have to worry about most of the +conditions! + +The only thing to worry is that the gadget has to have a single +configuration so a dual RNDIS and CDC ECM gadget won't work unless you +create a proper INF -- and of course, if you do submit it! + +*** Installing drivers for each function + +The other, trickier thing is making Windows install drivers for each +individual function. + +For mass storage it is trivial since Windows detect it's an interface +implementing USB Mass Storage class and selects appropriate driver. + +Things are harder with RDNIS and CDC ACM. + +**** RNDIS + +To make Windows select RNDIS drivers for the first function in the +gadget, one needs to use the [[file:linux.inf]] file provided with this +document. It "attaches" Window's RNDIS driver to the first interface +of the gadget. + +Please note, that while testing we encountered some issues[6] when +RNDIS was not the first interface. You do not need to worry abut it +unless you are trying to develop your own gadget in which case watch +out for this bug. + +**** CDC ACM + +Similarly, [[file:linux-cdc-acm.inf]] is provided for CDC ACM. + +**** Customising the gadget + +If you intend to hack the g_multi gadget be advised that rearranging +functions will obviously change interface numbers for each of the +functionality. As an effect provided INFs won't work since they have +interface numbers hard-coded in them (it's not hard to change those +though[7]). + +This also means, that after experimenting with g_multi and changing +provided functions one should change gadget's vendor and/or product ID +so there will be no collision with other customised gadgets or the +original gadget. + +Failing to comply may cause brain damage after wondering for hours why +things don't work as intended before realising Windows have cached +some drivers information (changing USB port may sometimes help plus +you might try using USBDeview[8] to remove the phantom device). + +**** INF testing + +Provided INF files have been tested on Windows XP SP3, Windows Vista +and Windows 7, all 32-bit versions. It should work on 64-bit versions +as well. It most likely won't work on Windows prior to Windows XP +SP2. + +** Other systems + +At this moment, drivers for any other systems have not been tested. +Knowing how MacOS is based on BSD and BSD is an Open Source it is +believed that it should (read: "I have no idea whether it will") work +out-of-the-box. + +For more exotic systems I have even less to say... + +Any testing and drivers *are* *welcome*! + +* Authors + +This document has been written by Michal Nazarewicz +([[mailto:mina86@mina86.com]]). INF files have been hacked with +support of Marek Szyprowski ([[mailto:m.szyprowski@samsung.com]]) and +Xiaofan Chen ([[mailto:xiaofanc@gmail.com]]) basing on the MS RNDIS +template[9], Microchip's CDC ACM INF file and David Brownell's +([[mailto:dbrownell@users.sourceforge.net]]) original INF files. + +* Footnotes + +[1] Remote Network Driver Interface Specification, +[[http://msdn.microsoft.com/en-us/library/ee484414.aspx]]. + +[2] Communications Device Class Abstract Control Model, spec for this +and other USB classes can be found at +[[http://www.usb.org/developers/devclass_docs/]]. + +[3] CDC Ethernet Control Model. + +[4] [[http://msdn.microsoft.com/en-us/library/ff537109(v=VS.85).aspx]] + +[5] [[http://msdn.microsoft.com/en-us/library/ff539234(v=VS.85).aspx]] + +[6] To put it in some other nice words, Windows failed to respond to +any user input. + +[7] You may find [[http://www.cygnal.org/ubb/Forum9/HTML/001050.html]] +useful. + +[8] http://www.nirsoft.net/utils/usb_devices_view.html + +[9] [[http://msdn.microsoft.com/en-us/library/ff570620.aspx]] diff --git a/Documentation/usb/linux-cdc-acm.inf b/Documentation/usb/linux-cdc-acm.inf index 14d2b87..612e722 100644 --- a/Documentation/usb/linux-cdc-acm.inf +++ b/Documentation/usb/linux-cdc-acm.inf @@ -90,10 +90,10 @@ ServiceBinary=%12%\USBSER.sys [SourceDisksFiles] [SourceDisksNames] [DeviceList] -%DESCRIPTION%=DriverInstall, USB\VID_0525&PID_A4A7 +%DESCRIPTION%=DriverInstall, USB\VID_0525&PID_A4A7, USB\VID_0525&PID_A4AB&MI_02 [DeviceList.NTamd64] -%DESCRIPTION%=DriverInstall, USB\VID_0525&PID_A4A7 +%DESCRIPTION%=DriverInstall, USB\VID_0525&PID_A4A7, USB\VID_0525&PID_A4AB&MI_02 ;------------------------------------------------------------------------------ diff --git a/Documentation/usb/linux.inf b/Documentation/usb/linux.inf index b9e538c..4dee958 100644 --- a/Documentation/usb/linux.inf +++ b/Documentation/usb/linux.inf @@ -18,15 +18,15 @@ DriverVer = 06/21/2006,6.0.6000.16384 ; Decoration for x86 architecture [LinuxDevices.NTx86] -%LinuxDevice% = RNDIS.NT.5.1, USB\VID_0525&PID_a4a2 +%LinuxDevice% = RNDIS.NT.5.1, USB\VID_0525&PID_a4a2, USB\VID_0525&PID_a4ab&MI_00 ; Decoration for x64 architecture [LinuxDevices.NTamd64] -%LinuxDevice% = RNDIS.NT.5.1, USB\VID_0525&PID_a4a2 +%LinuxDevice% = RNDIS.NT.5.1, USB\VID_0525&PID_a4a2, USB\VID_0525&PID_a4ab&MI_00 ; Decoration for ia64 architecture [LinuxDevices.NTia64] -%LinuxDevice% = RNDIS.NT.5.1, USB\VID_0525&PID_a4a2 +%LinuxDevice% = RNDIS.NT.5.1, USB\VID_0525&PID_a4a2, USB\VID_0525&PID_a4ab&MI_00 ;@@@ This is the common setting for setup [ControlFlags] -- cgit v1.1 From a93917d39fc388c4761d2530af82513e2d3bf9f6 Mon Sep 17 00:00:00 2001 From: Andy Shevchenko Date: Thu, 22 Jul 2010 17:53:56 +0300 Subject: USB: gadget: storage: optional SCSI WRITE FUA bit MS Windows mounts removable storage in "Removal optimized mode" by default. All the writes to the media are synchronous which is achieved by setting FUA (Force Unit Access) bit in SCSI WRITE(10,12) commands. This prevents I/O requests aggregation in block layer dramatically decreasing performance. This patch brings an option to accept or ignore mentioned bit a) via specifying module parameter "nofua", or b) through sysfs entry /sys/devices/platform/_UDC_/gadget/gadget-lunX/nofua (_UDC_ is the name of the USB Device Controller driver) Patch is based on the work that was done by Denis Karpov for Maemo 5 platform. Signed-off-by: Andy Shevchenko Acked-by: Alan Stern Cc: Denis Karpov Cc: Adrian Hunter Cc: David Brownell Signed-off-by: Greg Kroah-Hartman --- .../ABI/testing/sysfs-devices-platform-_UDC_-gadget | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'Documentation') diff --git a/Documentation/ABI/testing/sysfs-devices-platform-_UDC_-gadget b/Documentation/ABI/testing/sysfs-devices-platform-_UDC_-gadget index 3403402..d548eaa 100644 --- a/Documentation/ABI/testing/sysfs-devices-platform-_UDC_-gadget +++ b/Documentation/ABI/testing/sysfs-devices-platform-_UDC_-gadget @@ -7,3 +7,15 @@ Description: 0 -> resumed (_UDC_ is the name of the USB Device Controller driver) + +What: /sys/devices/platform/_UDC_/gadget/gadget-lunX/nofua +Date: July 2010 +Contact: Andy Shevchenko +Description: + Show or set the reaction on the FUA (Force Unit Access) bit in + the SCSI WRITE(10,12) commands when a gadget in USB Mass + Storage mode. + + Possible values are: + 1 -> ignore the FUA flag + 0 -> obey the FUA flag -- cgit v1.1