From 659d73ada5d6869dc18838c9125731a750389019 Mon Sep 17 00:00:00 2001 From: Thomas Abraham Date: Mon, 7 Nov 2011 01:02:21 +0530 Subject: gpio/samsung: Add device tree support for EXYNOS4 As gpio chips get registered, a device tree node which represents the gpio chip is searched and attached to it. A translate function is also provided to convert the gpio specifier into actual platform settings for pin function selection, pull up/down and driver strength settings. Signed-off-by: Thomas Abraham Acked-by: Grant Likely [kgene.kim@samsung.com: fixed build error] Signed-off-by: Kukjin Kim --- .../devicetree/bindings/gpio/gpio-samsung.txt | 40 ++++++++++++++++++++++ 1 file changed, 40 insertions(+) create mode 100644 Documentation/devicetree/bindings/gpio/gpio-samsung.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt new file mode 100644 index 0000000..8f50fe5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -0,0 +1,40 @@ +Samsung Exynos4 GPIO Controller + +Required properties: +- compatible: Compatible property value should be "samsung,exynos4-gpio>". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- #gpio-cells: Should be 4. The syntax of the gpio specifier used by client nodes + should be the following with values derived from the SoC user manual. + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [pull up/down] + [drive strength]> + + Values for gpio specifier: + - Pin number: is a value between 0 to 7. + - Pull Up/Down: 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 3 - Pull Up Enabled. + - Drive Strength: 0 - 1x, + 1 - 3x, + 2 - 2x, + 3 - 4x + +- gpio-controller: Specifies that the node is a gpio controller. +- #address-cells: should be 1. +- #size-cells: should be 1. + +Example: + + gpa0: gpio-controller@11400000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,exynos4-gpio"; + reg = <0x11400000 0x20>; + #gpio-cells = <4>; + gpio-controller; + }; -- cgit v1.1 From 26c919e1d3f4dff87ad50e104670f048cbc69b17 Mon Sep 17 00:00:00 2001 From: Thomas Abraham Date: Sun, 6 Nov 2011 22:10:44 +0530 Subject: serial: samsung: add device tree support Add device tree based discovery support for Samsung's uart controller. Cc: Ben Dooks Acked-by: Grant Likely Signed-off-by: Thomas Abraham Signed-off-by: Kukjin Kim --- Documentation/devicetree/bindings/serial/samsung_uart.txt | 14 ++++++++++++++ 1 file changed, 14 insertions(+) create mode 100644 Documentation/devicetree/bindings/serial/samsung_uart.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/serial/samsung_uart.txt b/Documentation/devicetree/bindings/serial/samsung_uart.txt new file mode 100644 index 0000000..2c8a17c --- /dev/null +++ b/Documentation/devicetree/bindings/serial/samsung_uart.txt @@ -0,0 +1,14 @@ +* Samsung's UART Controller + +The Samsung's UART controller is used for interfacing SoC with serial communicaion +devices. + +Required properties: +- compatible: should be + - "samsung,exynos4210-uart", for UART's compatible with Exynos4210 uart ports. + +- reg: base physical address of the controller and length of memory mapped + region. + +- interrupts: interrupt number to the cpu. The interrupt specifier format depends + on the interrupt controller parent. -- cgit v1.1 From 93ed55441245a39e3935f5cf1af3e22febcce905 Mon Sep 17 00:00:00 2001 From: Thomas Abraham Date: Mon, 24 Oct 2011 11:43:31 +0200 Subject: DMA: PL330: Add device tree support For PL330 dma controllers instantiated from device tree, the channel lookup is based on phandle of the dma controller and dma request id specified by the client node. During probe, the private data of each channel of the controller is set to point to the device node of the dma controller. The 'chan_id' of the each channel is used as the dma request id. Client driver requesting dma channels specify the phandle of the dma controller and the request id. The pl330 filter function converts the phandle to the device node pointer and matches that with channel's private data. If a match is found, the request id from the client node and the 'chan_id' of the channel is matched. A channel is found if both the values match. Acked-by: Jassi Brar Acked-by: Boojin Kim Signed-off-by: Thomas Abraham Reviewed-by: Rob Herring Acked-by: Grant Likely Acked-by: Vinod Koul Signed-off-by: Kukjin Kim --- .../devicetree/bindings/dma/arm-pl330.txt | 30 ++++++++++++++++++++++ 1 file changed, 30 insertions(+) create mode 100644 Documentation/devicetree/bindings/dma/arm-pl330.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/dma/arm-pl330.txt b/Documentation/devicetree/bindings/dma/arm-pl330.txt new file mode 100644 index 0000000..a4cd273 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/arm-pl330.txt @@ -0,0 +1,30 @@ +* ARM PrimeCell PL330 DMA Controller + +The ARM PrimeCell PL330 DMA controller can move blocks of memory contents +between memory and peripherals or memory to memory. + +Required properties: + - compatible: should include both "arm,pl330" and "arm,primecell". + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + +Example: + + pdma0: pdma@12680000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x12680000 0x1000>; + interrupts = <99>; + }; + +Client drivers (device nodes requiring dma transfers from dev-to-mem or +mem-to-dev) should specify the DMA channel numbers using a two-value pair +as shown below. + + [property name] = <[phandle of the dma controller] [dma request id]>; + + where 'dma request id' is the dma request number which is connected + to the client controller. The 'property name' is recommended to be + of the form -dma-channel. + + Example: tx-dma-channel = <&pdma0 12>; -- cgit v1.1 From b3d6ac3e5f937440a362c0fa187257fa1197f5b9 Mon Sep 17 00:00:00 2001 From: Thomas Abraham Date: Wed, 2 Nov 2011 19:37:22 +0900 Subject: input: samsung-keypad: Add device tree support Add device tree based discovery support for Samsung's keypad controller. Cc: Joonyoung Shim Cc: Donghwa Lee Signed-off-by: Thomas Abraham Acked-by: Grant Likely Signed-off-by: Kukjin Kim --- .../devicetree/bindings/input/samsung-keypad.txt | 88 ++++++++++++++++++++++ 1 file changed, 88 insertions(+) create mode 100644 Documentation/devicetree/bindings/input/samsung-keypad.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/input/samsung-keypad.txt b/Documentation/devicetree/bindings/input/samsung-keypad.txt new file mode 100644 index 0000000..ce3e394 --- /dev/null +++ b/Documentation/devicetree/bindings/input/samsung-keypad.txt @@ -0,0 +1,88 @@ +* Samsung's Keypad Controller device tree bindings + +Samsung's Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "samsung,s3c6410-keypad": For controllers compatible with s3c6410 keypad + controller. + - "samsung,s5pv210-keypad": For controllers compatible with s5pv210 keypad + controller. + +- reg: physical base address of the controller and length of memory mapped + region. + +- interrupts: The interrupt number to the cpu. + +Required Board Specific Properties: +- samsung,keypad-num-rows: Number of row lines connected to the keypad + controller. + +- samsung,keypad-num-columns: Number of column lines connected to the + keypad controller. + +- row-gpios: List of gpios used as row lines. The gpio specifier for + this property depends on the gpio controller to which these row lines + are connected. + +- col-gpios: List of gpios used as column lines. The gpio specifier for + this property depends on the gpio controller to which these column + lines are connected. + +- Keys represented as child nodes: Each key connected to the keypad + controller is represented as a child node to the keypad controller + device node and should include the following properties. + - keypad,row: the row number to which the key is connected. + - keypad,column: the column number to which the key is connected. + - linux,code: the key-code to be reported when the key is pressed + and released. + +Optional Properties specific to linux: +- linux,keypad-no-autorepeat: do no enable autorepeat feature. +- linux,keypad-wakeup: use any event on keypad as wakeup event. + + +Example: + keypad@100A0000 { + compatible = "samsung,s5pv210-keypad"; + reg = <0x100A0000 0x100>; + interrupts = <173>; + samsung,keypad-num-rows = <2>; + samsung,keypad-num-columns = <8>; + linux,input-no-autorepeat; + linux,input-wakeup; + + row-gpios = <&gpx2 0 3 3 0 + &gpx2 1 3 3 0>; + + col-gpios = <&gpx1 0 3 0 0 + &gpx1 1 3 0 0 + &gpx1 2 3 0 0 + &gpx1 3 3 0 0 + &gpx1 4 3 0 0 + &gpx1 5 3 0 0 + &gpx1 6 3 0 0 + &gpx1 7 3 0 0>; + + key_1 { + keypad,row = <0>; + keypad,column = <3>; + linux,code = <2>; + }; + + key_2 { + keypad,row = <0>; + keypad,column = <4>; + linux,code = <3>; + }; + + key_3 { + keypad,row = <0>; + keypad,column = <5>; + linux,code = <4>; + }; + }; -- cgit v1.1 From 39ce4084a604a3ef0e2836e074c02bbbcc7c1509 Mon Sep 17 00:00:00 2001 From: Thomas Abraham Date: Mon, 24 Oct 2011 14:49:04 +0200 Subject: rtc: rtc-s3c: Add device tree support Add device tree based discovery support for Samsung's rtc controller. Cc: Ben Dooks Signed-off-by: Thomas Abraham Acked-by: Grant Likely Signed-off-by: Kukjin Kim --- Documentation/devicetree/bindings/rtc/s3c-rtc.txt | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) create mode 100644 Documentation/devicetree/bindings/rtc/s3c-rtc.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt new file mode 100644 index 0000000..90ec45f --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -0,0 +1,20 @@ +* Samsung's S3C Real Time Clock controller + +Required properties: +- compatible: should be one of the following. + * "samsung,s3c2410-rtc" - for controllers compatible with s3c2410 rtc. + * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc. +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: Two interrupt numbers to the cpu should be specified. First + interrupt number is the rtc alarm interupt and second interrupt number + is the rtc tick interrupt. The number of cells representing a interrupt + depends on the parent interrupt controller. + +Example: + + rtc@10070000 { + compatible = "samsung,s3c6410-rtc"; + reg = <0x10070000 0x100>; + interrupts = <44 0 45 0>; + }; -- cgit v1.1 From 6b5ab4f442e32f248b6fad29aafd1d5153f4dbd3 Mon Sep 17 00:00:00 2001 From: Thomas Abraham Date: Sun, 6 Nov 2011 21:54:27 +0530 Subject: ARM: EXYNOS: Add Exynos4 device tree enabled board file Add a new EXYNOS4 compatible device tree enabled board file. Boards based on the EXYNOS4 family of SoC's can use this as the machine/board file. When using this machine fike, a corresponding device tree blob which describes the board's properties should be supplied at boot time to the kernel. Signed-off-by: Thomas Abraham Acked-by: Grant Likely Signed-off-by: Kukjin Kim --- Documentation/devicetree/bindings/arm/insignal-boards.txt | 8 ++++++++ Documentation/devicetree/bindings/arm/samsung-boards.txt | 8 ++++++++ 2 files changed, 16 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/insignal-boards.txt create mode 100644 Documentation/devicetree/bindings/arm/samsung-boards.txt (limited to 'Documentation') diff --git a/Documentation/devicetree/bindings/arm/insignal-boards.txt b/Documentation/devicetree/bindings/arm/insignal-boards.txt new file mode 100644 index 0000000..524c3dc --- /dev/null +++ b/Documentation/devicetree/bindings/arm/insignal-boards.txt @@ -0,0 +1,8 @@ +* Insignal's Exynos4210 based Origen evaluation board + +Origen low-cost evaluation board is based on Samsung's Exynos4210 SoC. + +Required root node properties: + - compatible = should be one or more of the following. + (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board. + (b) "samsung,exynos4210" - for boards based on Exynos4210 SoC. diff --git a/Documentation/devicetree/bindings/arm/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung-boards.txt new file mode 100644 index 0000000..0bf68be --- /dev/null +++ b/Documentation/devicetree/bindings/arm/samsung-boards.txt @@ -0,0 +1,8 @@ +* Samsung's Exynos4210 based SMDKV310 evaluation board + +SMDKV310 evaluation board is based on Samsung's Exynos4210 SoC. + +Required root node properties: + - compatible = should be one or more of the following. + (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board. + (b) "samsung,exynos4210" - for boards based on Exynos4210 SoC. -- cgit v1.1