From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- Documentation/arm/Sharp-LH/CompactFlash | 32 +++++++++ Documentation/arm/Sharp-LH/IOBarrier | 45 ++++++++++++ Documentation/arm/Sharp-LH/KEV7A400 | 8 +++ Documentation/arm/Sharp-LH/LPD7A400 | 15 ++++ Documentation/arm/Sharp-LH/LPD7A40X | 16 +++++ Documentation/arm/Sharp-LH/SDRAM | 51 ++++++++++++++ .../arm/Sharp-LH/VectoredInterruptController | 80 ++++++++++++++++++++++ 7 files changed, 247 insertions(+) create mode 100644 Documentation/arm/Sharp-LH/CompactFlash create mode 100644 Documentation/arm/Sharp-LH/IOBarrier create mode 100644 Documentation/arm/Sharp-LH/KEV7A400 create mode 100644 Documentation/arm/Sharp-LH/LPD7A400 create mode 100644 Documentation/arm/Sharp-LH/LPD7A40X create mode 100644 Documentation/arm/Sharp-LH/SDRAM create mode 100644 Documentation/arm/Sharp-LH/VectoredInterruptController (limited to 'Documentation/arm/Sharp-LH') diff --git a/Documentation/arm/Sharp-LH/CompactFlash b/Documentation/arm/Sharp-LH/CompactFlash new file mode 100644 index 0000000..8616d87 --- /dev/null +++ b/Documentation/arm/Sharp-LH/CompactFlash @@ -0,0 +1,32 @@ +README on the Compact Flash for Card Engines +============================================ + +There are three challenges in supporting the CF interface of the Card +Engines. First, every IO operation must be followed with IO to +another memory region. Second, the slot is wired for one-to-one +address mapping *and* it is wired for 16 bit access only. Second, the +interrupt request line from the CF device isn't wired. + +The IOBARRIER issue is covered in README.IOBARRIER. This isn't an +onerous problem. Enough said here. + +The addressing issue is solved in the +arch/arm/mach-lh7a40x/ide-lpd7a40x.c file with some awkward +work-arounds. We implement a special SELECT_DRIVE routine that is +called before the IDE driver performs its own SELECT_DRIVE. Our code +recognizes that the SELECT register cannot be modified without also +writing a command. It send an IDLE_IMMEDIATE command on selecting a +drive. The function also prevents drive select to the slave drive +since there can be only one. The awkward part is that the IDE driver, +even though we have a select procedure, also attempts to change the +drive by writing directly the SELECT register. This attempt is +explicitly blocked by the OUTB function--not pretty, but effective. + +The lack of interrupts is a more serious problem. Even though the CF +card is fast when compared to a normal IDE device, we don't know that +the CF is really flash. A user could use one of the very small hard +drives being shipped with a CF interface. The IDE code includes a +check for interfaces that lack an IRQ. In these cases, submitting a +command to the IDE controller is followed by a call to poll for +completion. If the device isn't immediately ready, it schedules a +timer to poll again later. diff --git a/Documentation/arm/Sharp-LH/IOBarrier b/Documentation/arm/Sharp-LH/IOBarrier new file mode 100644 index 0000000..c0d8853 --- /dev/null +++ b/Documentation/arm/Sharp-LH/IOBarrier @@ -0,0 +1,45 @@ +README on the IOBARRIER for CardEngine IO +========================================= + +Due to an unfortunate oversight when the Card Engines were designed, +the signals that control access to some peripherals, most notably the +SMC91C9111 ethernet controller, are not properly handled. + +The symptom is that some back to back IO with the peripheral returns +unreliable data. With the SMC chip, you'll see errors about the bank +register being 'screwed'. + +The cause is that the AEN signal to the SMC chip does not transition +for every memory access. It is driven through the CPLD from the CS7 +line of the CPU's static memory controller which is optimized to +eliminate unnecessary transitions. Yet, the SMC requires a transition +for every write access. The Sharp website has more information about +the effect this power-conserving feature has on peripheral +interfacing. + +The solution is to follow every write access to the SMC chip with an +access to another memory region that will force the CPU to release the +chip select line. It is important to guarantee that this access +forces the CPU off-chip. We map a page of SDRAM as if it were an +uncacheable IO device and read from it after every SMC IO write +operation. + + SMC IO + BARRIER IO + +Only this sequence is important. It does not matter that there is no +BARRIER IO before the access to the SMC chip because the AEN latch +only needs occurs after the SMC IO write cycle. The routines that +implement this work-around make an additional concession which is to +disable interrupts during the IO sequence. Other hardware devices +(the LogicPD CPLD) have registers in the same the physical memory +region as the SMC chip. An interrupt might allow an access to one of +those registers while SMC IO is being performed. + +You might be tempted to think that we have to access another device +attached to the static memory controller, but the empirical evidence +indicates that this is not so. Mapping 0x00000000 (flash) and +0xc0000000 (SDRAM) appear to have the same effect. Using SDRAM seems +to be faster. Choosing to access an undecoded memory region is not +desirable as there is no way to know how that chip select will be used +in the future. diff --git a/Documentation/arm/Sharp-LH/KEV7A400 b/Documentation/arm/Sharp-LH/KEV7A400 new file mode 100644 index 0000000..be32b14 --- /dev/null +++ b/Documentation/arm/Sharp-LH/KEV7A400 @@ -0,0 +1,8 @@ +README on Implementing Linux for Sharp's KEV7a400 +================================================= + +This product has been discontinued by Sharp. For the time being, the +partially implemented code remains in the kernel. At some point in +the future, either the code will be finished or it will be removed +completely. This depends primarily on how many of the development +boards are in the field. diff --git a/Documentation/arm/Sharp-LH/LPD7A400 b/Documentation/arm/Sharp-LH/LPD7A400 new file mode 100644 index 0000000..3275b45 --- /dev/null +++ b/Documentation/arm/Sharp-LH/LPD7A400 @@ -0,0 +1,15 @@ +README on Implementing Linux for the Logic PD LPD7A400-10 +========================================================= + +- CPLD memory mapping + + The board designers chose to use high address lines for controlling + access to the CPLD registers. It turns out to be a big waste + because we're using an MMU and must map IO space into virtual + memory. The result is that we have to make a mapping for every + register. + +- Serial Console + + It may be OK not to use the serial console option if the user passes + the console device name to the kernel. This deserves some exploration. diff --git a/Documentation/arm/Sharp-LH/LPD7A40X b/Documentation/arm/Sharp-LH/LPD7A40X new file mode 100644 index 0000000..8c29a27 --- /dev/null +++ b/Documentation/arm/Sharp-LH/LPD7A40X @@ -0,0 +1,16 @@ +README on Implementing Linux for the Logic PD LPD7A40X-10 +========================================================= + +- CPLD memory mapping + + The board designers chose to use high address lines for controlling + access to the CPLD registers. It turns out to be a big waste + because we're using an MMU and must map IO space into virtual + memory. The result is that we have to make a mapping for every + register. + +- Serial Console + + It may be OK not to use the serial console option if the user passes + the console device name to the kernel. This deserves some exploration. + diff --git a/Documentation/arm/Sharp-LH/SDRAM b/Documentation/arm/Sharp-LH/SDRAM new file mode 100644 index 0000000..93ddc23 --- /dev/null +++ b/Documentation/arm/Sharp-LH/SDRAM @@ -0,0 +1,51 @@ +README on the SDRAM Controller for the LH7a40X +============================================== + +The standard configuration for the SDRAM controller generates a sparse +memory array. The precise layout is determined by the SDRAM chips. A +default kernel configuration assembles the discontiguous memory +regions into separate memory nodes via the NUMA (Non-Uniform Memory +Architecture) facilities. In this default configuration, the kernel +is forgiving about the precise layout. As long as it is given an +accurate picture of available memory by the bootloader the kernel will +execute correctly. + +The SDRC supports a mode where some of the chip select lines are +swapped in order to make SDRAM look like a synchronous ROM. Setting +this bit means that the RAM will present as a contiguous array. Some +programmers prefer this to the discontiguous layout. Be aware that +may be a penalty for this feature where some some configurations of +memory are significantly reduced; i.e. 64MiB of RAM appears as only 32 +MiB. + +There are a couple of configuration options to override the default +behavior. When the SROMLL bit is set and memory appears as a +contiguous array, there is no reason to support NUMA. +CONFIG_LH7A40X_CONTIGMEM disables NUMA support. When physical memory +is discontiguous, the memory tables are organized such that there are +two banks per nodes with a small gap between them. This layout wastes +some kernel memory for page tables representing non-existent memory. +CONFIG_LH7A40X_ONE_BANK_PER_NODE optimizes the node tables such that +there are no gaps. These options control the low level organization +of the memory management tables in ways that may prevent the kernel +from booting or may cause the kernel to allocated excessively large +page tables. Be warned. Only change these options if you know what +you are doing. The default behavior is a reasonable compromise that +will suit all users. + +-- + +A typical 32MiB system with the default configuration options will +find physical memory managed as follows. + + node 0: 0xc0000000 4MiB + 0xc1000000 4MiB + node 1: 0xc4000000 4MiB + 0xc5000000 4MiB + node 2: 0xc8000000 4MiB + 0xc9000000 4MiB + node 3: 0xcc000000 4MiB + 0xcd000000 4MiB + +Setting CONFIG_LH7A40X_ONE_BANK_PER_NODE will put each bank into a +separate node. diff --git a/Documentation/arm/Sharp-LH/VectoredInterruptController b/Documentation/arm/Sharp-LH/VectoredInterruptController new file mode 100644 index 0000000..23047e9 --- /dev/null +++ b/Documentation/arm/Sharp-LH/VectoredInterruptController @@ -0,0 +1,80 @@ +README on the Vectored Interrupt Controller of the LH7A404 +========================================================== + +The 404 revision of the LH7A40X series comes with two vectored +interrupts controllers. While the kernel does use some of the +features of these devices, it is far from the purpose for which they +were designed. + +When this README was written, the implementation of the VICs was in +flux. It is possible that some details, especially with priorities, +will change. + +The VIC support code is inspired by routines written by Sharp. + + +Priority Control +---------------- + +The significant reason for using the VIC's vectoring is to control +interrupt priorities. There are two tables in +arch/arm/mach-lh7a40x/irq-lh7a404.c that look something like this. + + static unsigned char irq_pri_vic1[] = { IRQ_GPIO3INTR, }; + static unsigned char irq_pri_vic2[] = { + IRQ_T3UI, IRQ_GPIO7INTR, + IRQ_UART1INTR, IRQ_UART2INTR, IRQ_UART3INTR, }; + +The initialization code reads these tables and inserts a vector +address and enable for each indicated IRQ. Vectored interrupts have +higher priority than non-vectored interrupts. So, on VIC1, +IRQ_GPIO3INTR will be served before any other non-FIQ interrupt. Due +to the way that the vectoring works, IRQ_T3UI is the next highest +priority followed by the other vectored interrupts on VIC2. After +that, the non-vectored interrupts are scanned in VIC1 then in VIC2. + + +ISR +--- + +The interrupt service routine macro get_irqnr() in +arch/arm/kernel/entry-armv.S scans the VICs for the next active +interrupt. The vectoring makes this code somewhat larger than it was +before using vectoring (refer to the LH7A400 implementation). In the +case where an interrupt is vectored, the implementation will tend to +be faster than the non-vectored version. However, the worst-case path +is longer. + +It is worth noting that at present, there is no need to read +VIC2_VECTADDR because the register appears to be shared between the +controllers. The code is written such that if this changes, it ought +to still work properly. + + +Vector Addresses +---------------- + +The proper use of the vectoring hardware would jump to the ISR +specified by the vectoring address. Linux isn't structured to take +advantage of this feature, though it might be possible to change +things to support it. + +In this implementation, the vectoring address is used to speed the +search for the active IRQ. The address is coded such that the lowest +6 bits store the IRQ number for vectored interrupts. These numbers +correspond to the bits in the interrupt status registers. IRQ zero is +the lowest interrupt bit in VIC1. IRQ 32 is the lowest interrupt bit +in VIC2. Because zero is a valid IRQ number and because we cannot +detect whether or not there is a valid vectoring address if that +address is zero, the eigth bit (0x100) is set for vectored interrupts. +The address for IRQ 0x18 (VIC2) is 0x118. Only the ninth bit is set +for the default handler on VIC1 and only the tenth bit is set for the +default handler on VIC2. + +In other words. + + 0x000 - no active interrupt + 0x1ii - vectored interrupt 0xii + 0x2xx - unvectored interrupt on VIC1 (xx is don't care) + 0x4xx - unvectored interrupt on VIC2 (xx is don't care) + -- cgit v1.1