From e5c1721894415d00a55c2650ed6536b644799c50 Mon Sep 17 00:00:00 2001 From: Ashish Gupta Date: Wed, 22 Sep 2010 08:11:56 +0000 Subject: Blackfin: tll6527m: new board port Signed-off-by: Ashish Gupta Signed-off-by: Mike Frysinger --- arch/blackfin/configs/BF527-TLL6527M_defconfig | 180 +++++ arch/blackfin/mach-bf527/boards/Kconfig | 5 + arch/blackfin/mach-bf527/boards/Makefile | 1 + arch/blackfin/mach-bf527/boards/tll6527m.c | 986 +++++++++++++++++++++++++ 4 files changed, 1172 insertions(+) create mode 100644 arch/blackfin/configs/BF527-TLL6527M_defconfig create mode 100644 arch/blackfin/mach-bf527/boards/tll6527m.c diff --git a/arch/blackfin/configs/BF527-TLL6527M_defconfig b/arch/blackfin/configs/BF527-TLL6527M_defconfig new file mode 100644 index 0000000..92ded5e --- /dev/null +++ b/arch/blackfin/configs/BF527-TLL6527M_defconfig @@ -0,0 +1,180 @@ +CONFIG_EXPERIMENTAL=y +CONFIG_LOCALVERSION="DEV_0-1_pre2010" +CONFIG_SYSVIPC=y +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_EMBEDDED=y +# CONFIG_SYSCTL_SYSCALL is not set +# CONFIG_ELF_CORE is not set +# CONFIG_FUTEX is not set +# CONFIG_SIGNALFD is not set +# CONFIG_TIMERFD is not set +# CONFIG_EVENTFD is not set +# CONFIG_AIO is not set +CONFIG_SLAB=y +CONFIG_MMAP_ALLOW_UNINITIALIZED=y +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_LBDAF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_IOSCHED_DEADLINE is not set +CONFIG_PREEMPT_VOLUNTARY=y +CONFIG_BF527=y +CONFIG_BF_REV_0_2=y +CONFIG_BFIN527_TLL6527M=y +CONFIG_BF527_UART1_PORTG=y +CONFIG_IRQ_USB_INT0=11 +CONFIG_IRQ_USB_INT1=11 +CONFIG_IRQ_USB_INT2=11 +CONFIG_IRQ_USB_DMA=11 +CONFIG_BOOT_LOAD=0x400000 +# CONFIG_CYCLES_CLOCKSOURCE is not set +# CONFIG_SCHEDULE_L1 is not set +# CONFIG_MEMSET_L1 is not set +# CONFIG_MEMCPY_L1 is not set +# CONFIG_SYS_BFIN_SPINLOCK_L1 is not set +CONFIG_NOMMU_INITIAL_TRIM_EXCESS=0 +CONFIG_BFIN_GPTIMERS=y +CONFIG_DMA_UNCACHED_2M=y +CONFIG_C_CDPRIO=y +CONFIG_BANK_0=0xFFC2 +CONFIG_BANK_1=0xFFC2 +CONFIG_BANK_2=0xFFC2 +CONFIG_BANK_3=0xFFC2 +CONFIG_BINFMT_FLAT=y +CONFIG_BINFMT_ZFLAT=y +CONFIG_NET=y +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_INET=y +CONFIG_IP_PNP=y +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set +# CONFIG_INET_DIAG is not set +# CONFIG_IPV6 is not set +CONFIG_IRDA=m +CONFIG_IRLAN=m +CONFIG_IRCOMM=m +CONFIG_IRTTY_SIR=m +CONFIG_BFIN_SIR=m +CONFIG_BFIN_SIR0=y +# CONFIG_WIRELESS is not set +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_FW_LOADER is not set +CONFIG_MTD=y +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLOCK=y +CONFIG_MTD_CFI=y +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_RAM=y +CONFIG_MTD_ROM=y +CONFIG_MTD_COMPLEX_MAPPINGS=y +CONFIG_MTD_GPIO_ADDR=y +CONFIG_BLK_DEV_RAM=y +CONFIG_SCSI=y +# CONFIG_SCSI_PROC_FS is not set +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_DEV_SR=m +# CONFIG_SCSI_LOWLEVEL is not set +CONFIG_NETDEVICES=y +CONFIG_NET_ETHERNET=y +CONFIG_BFIN_MAC=y +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_WLAN is not set +# CONFIG_INPUT_MOUSEDEV is not set +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_AD7879=m +CONFIG_INPUT_MISC=y +CONFIG_INPUT_AD714X=y +CONFIG_INPUT_ADXL34X=y +# CONFIG_SERIO is not set +CONFIG_BFIN_PPI=m +CONFIG_BFIN_SIMPLE_TIMER=m +CONFIG_BFIN_SPORT=m +# CONFIG_CONSOLE_TRANSLATIONS is not set +# CONFIG_DEVKMEM is not set +CONFIG_BFIN_JTAG_COMM=m +CONFIG_SERIAL_BFIN=y +CONFIG_SERIAL_BFIN_CONSOLE=y +CONFIG_SERIAL_BFIN_UART1=y +# CONFIG_LEGACY_PTYS is not set +# CONFIG_HW_RANDOM is not set +CONFIG_I2C_CHARDEV=y +# CONFIG_I2C_HELPER_AUTO is not set +CONFIG_I2C_SMBUS=y +CONFIG_I2C_BLACKFIN_TWI=y +CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=100 +CONFIG_GPIOLIB=y +CONFIG_GPIO_SYSFS=y +# CONFIG_HWMON is not set +CONFIG_WATCHDOG=y +CONFIG_BFIN_WDT=y +CONFIG_MEDIA_SUPPORT=y +CONFIG_VIDEO_DEV=y +# CONFIG_MEDIA_TUNER_CUSTOMISE is not set +CONFIG_VIDEO_HELPER_CHIPS_AUTO=y +CONFIG_VIDEO_BLACKFIN_CAM=m +CONFIG_OV9655=y +CONFIG_FB=y +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_FRAMEBUFFER_CONSOLE=y +CONFIG_FONTS=y +CONFIG_FONT_6x11=y +CONFIG_LOGO=y +# CONFIG_LOGO_LINUX_MONO is not set +# CONFIG_LOGO_LINUX_VGA16 is not set +# CONFIG_LOGO_LINUX_CLUT224 is not set +# CONFIG_LOGO_BLACKFIN_VGA16 is not set +CONFIG_SOUND=y +CONFIG_SND=y +CONFIG_SND_MIXER_OSS=y +CONFIG_SND_PCM_OSS=y +CONFIG_SND_SOC=y +CONFIG_SND_BF5XX_I2S=y +CONFIG_SND_BF5XX_SOC_SSM2602=y +# CONFIG_HID_SUPPORT is not set +# CONFIG_USB_SUPPORT is not set +CONFIG_MMC=m +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_BFIN=y +CONFIG_EXT2_FS=y +# CONFIG_DNOTIFY is not set +CONFIG_ISO9660_FS=m +CONFIG_JOLIET=y +CONFIG_UDF_FS=m +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_JFFS2_FS=y +CONFIG_NFS_FS=m +CONFIG_NFS_V3=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +CONFIG_NLS_CODEPAGE_437=m +CONFIG_NLS_CODEPAGE_936=m +CONFIG_NLS_ISO8859_1=m +CONFIG_NLS_UTF8=m +CONFIG_DEBUG_KERNEL=y +CONFIG_DEBUG_SHIRQ=y +CONFIG_DETECT_HUNG_TASK=y +CONFIG_DEBUG_INFO=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set +# CONFIG_FTRACE is not set +CONFIG_DEBUG_MMRS=y +CONFIG_DEBUG_HWERR=y +CONFIG_EXACT_HWERR=y +CONFIG_DEBUG_DOUBLEFAULT=y +CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE=y +CONFIG_EARLY_PRINTK=y +CONFIG_CPLB_INFO=y +CONFIG_SECURITY=y +CONFIG_CRYPTO=y +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRC7=m diff --git a/arch/blackfin/mach-bf527/boards/Kconfig b/arch/blackfin/mach-bf527/boards/Kconfig index 646bc66..1cc2667 100644 --- a/arch/blackfin/mach-bf527/boards/Kconfig +++ b/arch/blackfin/mach-bf527/boards/Kconfig @@ -29,4 +29,9 @@ config BFIN527_AD7160EVAL help BF527-AD7160-EVAL board support. +config BFIN527_TLL6527M + bool "The Learning Labs TLL6527M" + help + TLL6527M V1.0 platform support + endchoice diff --git a/arch/blackfin/mach-bf527/boards/Makefile b/arch/blackfin/mach-bf527/boards/Makefile index 751d45c..1d67da9 100644 --- a/arch/blackfin/mach-bf527/boards/Makefile +++ b/arch/blackfin/mach-bf527/boards/Makefile @@ -7,3 +7,4 @@ obj-$(CONFIG_BFIN527_EZKIT_V2) += ezkit.o obj-$(CONFIG_BFIN527_BLUETECHNIX_CM) += cm_bf527.o obj-$(CONFIG_BFIN526_EZBRD) += ezbrd.o obj-$(CONFIG_BFIN527_AD7160EVAL) += ad7160eval.o +obj-$(CONFIG_BFIN527_TLL6527M) += tll6527m.o diff --git a/arch/blackfin/mach-bf527/boards/tll6527m.c b/arch/blackfin/mach-bf527/boards/tll6527m.c new file mode 100644 index 0000000..ae4130e --- /dev/null +++ b/arch/blackfin/mach-bf527/boards/tll6527m.c @@ -0,0 +1,986 @@ +/* File: arch/blackfin/mach-bf527/boards/tll6527m.c + * Based on: arch/blackfin/mach-bf527/boards/ezkit.c + * Author: Ashish Gupta + * + * Copyright: 2010 - The Learning Labs Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#if defined(CONFIG_TOUCHSCREEN_AD7879) \ + || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE) +#include +#define LCD_BACKLIGHT_GPIO 0x40 +/* TLL6527M uses TLL7UIQ35 / ADI LCD EZ Extender. AD7879 AUX GPIO is used for + * LCD Backlight Enable + */ +#endif + +/* + * Name the Board for the /proc/cpuinfo + */ +const char bfin_board_name[] = "TLL6527M"; +/* + * Driver needs to know address, irq and flag pin. + */ + +#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE) +static struct resource musb_resources[] = { + [0] = { + .start = 0xffc03800, + .end = 0xffc03cff, + .flags = IORESOURCE_MEM, + }, + [1] = { /* general IRQ */ + .start = IRQ_USB_INT0, + .end = IRQ_USB_INT0, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, + [2] = { /* DMA IRQ */ + .start = IRQ_USB_DMA, + .end = IRQ_USB_DMA, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct musb_hdrc_config musb_config = { + .multipoint = 0, + .dyn_fifo = 0, + .soft_con = 1, + .dma = 1, + .num_eps = 8, + .dma_channels = 8, + /*.gpio_vrsel = GPIO_PG13,*/ + /* Some custom boards need to be active low, just set it to "0" + * if it is the case. + */ + .gpio_vrsel_active = 1, +}; + +static struct musb_hdrc_platform_data musb_plat = { +#if defined(CONFIG_USB_MUSB_OTG) + .mode = MUSB_OTG, +#elif defined(CONFIG_USB_MUSB_HDRC_HCD) + .mode = MUSB_HOST, +#elif defined(CONFIG_USB_GADGET_MUSB_HDRC) + .mode = MUSB_PERIPHERAL, +#endif + .config = &musb_config, +}; + +static u64 musb_dmamask = ~(u32)0; + +static struct platform_device musb_device = { + .name = "musb_hdrc", + .id = 0, + .dev = { + .dma_mask = &musb_dmamask, + .coherent_dma_mask = 0xffffffff, + .platform_data = &musb_plat, + }, + .num_resources = ARRAY_SIZE(musb_resources), + .resource = musb_resources, +}; +#endif + +#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE) +#include + +static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = { + .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB, + .ppi_mode = USE_RGB565_16_BIT_PPI, + .use_bl = 1, + .gpio_bl = LCD_BACKLIGHT_GPIO, +}; + +static struct resource bfin_lq035q1_resources[] = { + { + .start = IRQ_PPI_ERROR, + .end = IRQ_PPI_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_lq035q1_device = { + .name = "bfin-lq035q1", + .id = -1, + .num_resources = ARRAY_SIZE(bfin_lq035q1_resources), + .resource = bfin_lq035q1_resources, + .dev = { + .platform_data = &bfin_lq035q1_data, + }, +}; +#endif + +#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) +static struct mtd_partition tll6527m_partitions[] = { + { + .name = "bootloader(nor)", + .size = 0xA0000, + .offset = 0, + }, { + .name = "linux kernel(nor)", + .size = 0xD00000, + .offset = MTDPART_OFS_APPEND, + }, { + .name = "file system(nor)", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + } +}; + +static struct physmap_flash_data tll6527m_flash_data = { + .width = 2, + .parts = tll6527m_partitions, + .nr_parts = ARRAY_SIZE(tll6527m_partitions), +}; + +static unsigned tll6527m_flash_gpios[] = { GPIO_PG11, GPIO_PH11, GPIO_PH12 }; + +static struct resource tll6527m_flash_resource[] = { + { + .name = "cfi_probe", + .start = 0x20000000, + .end = 0x201fffff, + .flags = IORESOURCE_MEM, + }, { + .start = (unsigned long)tll6527m_flash_gpios, + .end = ARRAY_SIZE(tll6527m_flash_gpios), + .flags = IORESOURCE_IRQ, + } +}; + +static struct platform_device tll6527m_flash_device = { + .name = "gpio-addr-flash", + .id = 0, + .dev = { + .platform_data = &tll6527m_flash_data, + }, + .num_resources = ARRAY_SIZE(tll6527m_flash_resource), + .resource = tll6527m_flash_resource, +}; +#endif + +#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE) +/* An SN74LVC138A 3:8 decoder chip has been used to generate 7 augmented + * outputs used as SPI CS lines for all SPI SLAVE devices on TLL6527v1-0. + * EXP_GPIO_SPISEL_BASE is the base number for the expanded outputs being + * used as SPI CS lines, this should be > MAX_BLACKFIN_GPIOS + */ +#include +#define EXP_GPIO_SPISEL_BASE 0x64 +static unsigned gpio_addr_inputs[] = { + GPIO_PG1, GPIO_PH9, GPIO_PH10 +}; + +static struct gpio_decoder_platfrom_data spi_decoded_cs = { + .base = EXP_GPIO_SPISEL_BASE, + .input_addrs = gpio_addr_inputs, + .nr_input_addrs = ARRAY_SIZE(gpio_addr_inputs), + .default_output = 0, +/* .default_output = (1 << ARRAY_SIZE(gpio_addr_inputs)) - 1 */ +}; + +static struct platform_device spi_decoded_gpio = { + .name = "gpio-decoder", + .id = 0, + .dev = { + .platform_data = &spi_decoded_cs, + }, +}; + +#else +#define EXP_GPIO_SPISEL_BASE 0x0 + +#endif + +#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE) +#include +static const struct adxl34x_platform_data adxl345_info = { + .x_axis_offset = 0, + .y_axis_offset = 0, + .z_axis_offset = 0, + .tap_threshold = 0x31, + .tap_duration = 0x10, + .tap_latency = 0x60, + .tap_window = 0xF0, + .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN, + .act_axis_control = 0xFF, + .activity_threshold = 5, + .inactivity_threshold = 2, + .inactivity_time = 2, + .free_fall_threshold = 0x7, + .free_fall_time = 0x20, + .data_rate = 0x8, + .data_range = ADXL_FULL_RES, + + .ev_type = EV_ABS, + .ev_code_x = ABS_X, /* EV_REL */ + .ev_code_y = ABS_Y, /* EV_REL */ + .ev_code_z = ABS_Z, /* EV_REL */ + + .ev_code_tap = {BTN_TOUCH, BTN_TOUCH, BTN_TOUCH}, /* EV_KEY x,y,z */ + +/* .ev_code_ff = KEY_F,*/ /* EV_KEY */ + .ev_code_act_inactivity = KEY_A, /* EV_KEY */ + .use_int2 = 1, + .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK, + .fifo_mode = ADXL_FIFO_STREAM, +}; +#endif + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) +static struct platform_device bfin_mii_bus = { + .name = "bfin_mii_bus", +}; + +static struct platform_device bfin_mac_device = { + .name = "bfin_mac", + .dev.platform_data = &bfin_mii_bus, +}; +#endif + +#if defined(CONFIG_MTD_M25P80) \ + || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader(spi)", + .size = 0x00040000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + }, { + .name = "linux kernel(spi)", + .size = MTDPART_SIZ_FULL, + .offset = MTDPART_OFS_APPEND, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p16", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_BFIN_SPI_ADC) \ + || defined(CONFIG_BFIN_SPI_ADC_MODULE) +/* SPI ADC chip */ +static struct bfin5xx_spi_chip spi_adc_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ +/* + * tll6527m V1.0 does not support native spi slave selects + * hence DMA mode will not be useful since the ADC needs + * CS to toggle for each sample and cs_change_per_word + * seems to be removed from spi_bfin5xx.c + */ + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) +static struct bfin5xx_spi_chip mmc_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_TOUCHSCREEN_AD7879) \ + || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE) +static const struct ad7879_platform_data bfin_ad7879_ts_info = { + .model = 7879, /* Model = AD7879 */ + .x_plate_ohms = 620, /* 620 Ohm from the touch datasheet */ + .pressure_max = 10000, + .pressure_min = 0, + .first_conversion_delay = 3, + /* wait 512us before do a first conversion */ + .acquisition_time = 1, /* 4us acquisition time per sample */ + .median = 2, /* do 8 measurements */ + .averaging = 1, + /* take the average of 4 middle samples */ + .pen_down_acc_interval = 255, /* 9.4 ms */ + .gpio_export = 1, /* configure AUX as GPIO output*/ + .gpio_base = LCD_BACKLIGHT_GPIO, +}; +#endif + +#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \ + || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE) +static struct bfin5xx_spi_chip spi_ad7879_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) +static struct bfin5xx_spi_chip spidev_chip_info = { + .enable_dma = 0, + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) +static struct platform_device bfin_i2s = { + .name = "bfin-i2s", + .id = CONFIG_SND_BF5XX_SPORT_NUM, + /* TODO: add platform data here */ +}; +#endif + +#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE) +static struct bfin5xx_spi_chip lq035q1_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE) +static struct bfin5xx_spi_chip spi_mcp23s08_sys_chip_info = { + .enable_dma = 0, + .bits_per_word = 8, +}; + +static struct bfin5xx_spi_chip spi_mcp23s08_usr_chip_info = { + .enable_dma = 0, + .bits_per_word = 8, +}; + +#include +static const struct mcp23s08_platform_data bfin_mcp23s08_sys_gpio_info = { + .chip[0].is_present = true, + .base = 0x30, +}; +static const struct mcp23s08_platform_data bfin_mcp23s08_usr_gpio_info = { + .chip[2].is_present = true, + .base = 0x38, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) \ + || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 25000000, + /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS, + /* Can be connected to TLL6527M GPIO connector */ + /* Either SPI_ADC or M25P80 FLASH can be installed at a time */ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_BFIN_SPI_ADC) + || defined(CONFIG_BFIN_SPI_ADC_MODULE) + { + .modalias = "bfin_spi_adc", + /* Name of spi_driver for this device */ + .max_speed_hz = 10000000, + /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS, + /* Framework chip select. */ + .platform_data = NULL, /* No spi_driver specific config */ + .controller_data = &spi_adc_chip_info, + .mode = SPI_MODE_0, + }, +#endif + +#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) + { + .modalias = "mmc_spi", +/* + * TLL6527M V1.0 does not support SD Card at SPI Clock > 10 MHz due to + * SPI buffer limitations + */ + .max_speed_hz = 10000000, + /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = EXP_GPIO_SPISEL_BASE + 0x05 + MAX_CTRL_CS, + .controller_data = &mmc_spi_chip_info, + .mode = SPI_MODE_0, + }, +#endif +#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \ + || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE) + { + .modalias = "ad7879", + .platform_data = &bfin_ad7879_ts_info, + .irq = IRQ_PH14, + .max_speed_hz = 5000000, + /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = EXP_GPIO_SPISEL_BASE + 0x07 + MAX_CTRL_CS, + .controller_data = &spi_ad7879_chip_info, + .mode = SPI_CPHA | SPI_CPOL, + }, +#endif +#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) + { + .modalias = "spidev", + .max_speed_hz = 10000000, + /* TLL6527Mv1-0 supports max spi clock (SCK) speed = 10 MHz */ + .bus_num = 0, + .chip_select = EXP_GPIO_SPISEL_BASE + 0x03 + MAX_CTRL_CS, + .mode = SPI_CPHA | SPI_CPOL, + .controller_data = &spidev_chip_info, + }, +#endif +#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE) + { + .modalias = "bfin-lq035q1-spi", + .max_speed_hz = 20000000, + .bus_num = 0, + .chip_select = EXP_GPIO_SPISEL_BASE + 0x06 + MAX_CTRL_CS, + .controller_data = &lq035q1_spi_chip_info, + .mode = SPI_CPHA | SPI_CPOL, + }, +#endif +#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE) + { + .modalias = "mcp23s08", + .platform_data = &bfin_mcp23s08_sys_gpio_info, + .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = EXP_GPIO_SPISEL_BASE + 0x01 + MAX_CTRL_CS, + .controller_data = &spi_mcp23s08_sys_chip_info, + .mode = SPI_CPHA | SPI_CPOL, + }, + { + .modalias = "mcp23s08", + .platform_data = &bfin_mcp23s08_usr_gpio_info, + .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = EXP_GPIO_SPISEL_BASE + 0x02 + MAX_CTRL_CS, + .controller_data = &spi_mcp23s08_usr_chip_info, + .mode = SPI_CPHA | SPI_CPOL, + }, +#endif +}; + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* SPI controller data */ +static struct bfin5xx_spi_master bfin_spi0_info = { + .num_chipselect = EXP_GPIO_SPISEL_BASE + 8 + MAX_CTRL_CS, + /* EXP_GPIO_SPISEL_BASE will be > MAX_BLACKFIN_GPIOS */ + .enable_dma = 1, /* master has the ability to do dma transfer */ + .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, +}; + +/* SPI (0) */ +static struct resource bfin_spi0_resource[] = { + [0] = { + .start = SPI0_REGBASE, + .end = SPI0_REGBASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CH_SPI, + .end = CH_SPI, + .flags = IORESOURCE_DMA, + }, + [2] = { + .start = IRQ_SPI, + .end = IRQ_SPI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_spi0_device = { + .name = "bfin-spi", + .id = 0, /* Bus number */ + .num_resources = ARRAY_SIZE(bfin_spi0_resource), + .resource = bfin_spi0_resource, + .dev = { + .platform_data = &bfin_spi0_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +#ifdef CONFIG_SERIAL_BFIN_UART0 +static struct resource bfin_uart0_resources[] = { + { + .start = UART0_THR, + .end = UART0_GCTL+2, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART0_ERROR, + .end = IRQ_UART0_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_TX, + .end = CH_UART0_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX, + .flags = IORESOURCE_DMA, + }, +}; + +unsigned short bfin_uart0_peripherals[] = { + P_UART0_TX, P_UART0_RX, 0 +}; + +static struct platform_device bfin_uart0_device = { + .name = "bfin-uart", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_uart0_resources), + .resource = bfin_uart0_resources, + .dev = { + .platform_data = &bfin_uart0_peripherals, + /* Passed to driver */ + }, +}; +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 +static struct resource bfin_uart1_resources[] = { + { + .start = UART1_THR, + .end = UART1_GCTL+2, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART1_ERROR, + .end = IRQ_UART1_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_TX, + .end = CH_UART1_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX, + .flags = IORESOURCE_DMA, + }, +#ifdef CONFIG_BFIN_UART1_CTSRTS + { /* CTS pin */ + .start = GPIO_PF9, + .end = GPIO_PF9, + .flags = IORESOURCE_IO, + }, + { /* RTS pin */ + .start = GPIO_PF10, + .end = GPIO_PF10, + .flags = IORESOURCE_IO, + }, +#endif +}; + +unsigned short bfin_uart1_peripherals[] = { + P_UART1_TX, P_UART1_RX, 0 +}; + +static struct platform_device bfin_uart1_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart1_resources), + .resource = bfin_uart1_resources, + .dev = { + .platform_data = &bfin_uart1_peripherals, + /* Passed to driver */ + }, +}; +#endif +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#ifdef CONFIG_BFIN_SIR0 +static struct resource bfin_sir0_resources[] = { + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX+1, + .flags = IORESOURCE_DMA, + }, +}; + +static struct platform_device bfin_sir0_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir0_resources), + .resource = bfin_sir0_resources, +}; +#endif +#ifdef CONFIG_BFIN_SIR1 +static struct resource bfin_sir1_resources[] = { + { + .start = 0xFFC02000, + .end = 0xFFC020FF, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX+1, + .flags = IORESOURCE_DMA, + }, +}; + +static struct platform_device bfin_sir1_device = { + .name = "bfin_sir", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sir1_resources), + .resource = bfin_sir1_resources, +}; +#endif +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) +static struct resource bfin_twi0_resource[] = { + [0] = { + .start = TWI0_REGBASE, + .end = TWI0_REGBASE, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TWI, + .end = IRQ_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device i2c_bfin_twi_device = { + .name = "i2c-bfin-twi", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_twi0_resource), + .resource = bfin_twi0_resource, +}; +#endif + +static struct i2c_board_info __initdata bfin_i2c_board_info[] = { +#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE) + { + I2C_BOARD_INFO("pcf8574_lcd", 0x22), + }, +#endif + +#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE) + { + I2C_BOARD_INFO("bfin-adv7393", 0x2B), + }, +#endif +#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) \ + || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE) + { + I2C_BOARD_INFO("ad7879", 0x2C), + .irq = IRQ_PH14, + .platform_data = (void *)&bfin_ad7879_ts_info, + }, +#endif +#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE) + { + I2C_BOARD_INFO("ssm2602", 0x1b), + }, +#endif + { + I2C_BOARD_INFO("adm1192", 0x2e), + }, + + { + I2C_BOARD_INFO("ltc3576", 0x09), + }, +#if defined(CONFIG_INPUT_ADXL34X_I2C) \ + || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE) + { + I2C_BOARD_INFO("adxl34x", 0x53), + .irq = IRQ_PH13, + .platform_data = (void *)&adxl345_info, + }, +#endif +}; + +#if defined(CONFIG_SERIAL_BFIN_SPORT) \ + || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART +static struct resource bfin_sport0_uart_resources[] = { + { + .start = SPORT0_TCR1, + .end = SPORT0_MRCS3+4, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_SPORT0_RX, + .end = IRQ_SPORT0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_SPORT0_ERROR, + .end = IRQ_SPORT0_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +unsigned short bfin_sport0_peripherals[] = { + P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS, + P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0 +}; + +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources), + .resource = bfin_sport0_uart_resources, + .dev = { + .platform_data = &bfin_sport0_peripherals, + /* Passed to driver */ + }, +}; +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART +static struct resource bfin_sport1_uart_resources[] = { + { + .start = SPORT1_TCR1, + .end = SPORT1_MRCS3+4, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_SPORT1_RX, + .end = IRQ_SPORT1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_SPORT1_ERROR, + .end = IRQ_SPORT1_ERROR, + .flags = IORESOURCE_IRQ, + }, +}; + +unsigned short bfin_sport1_peripherals[] = { + P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS, + P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0 +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources), + .resource = bfin_sport1_uart_resources, + .dev = { + .platform_data = &bfin_sport1_peripherals, + /* Passed to driver */ + }, +}; +#endif +#endif + +static const unsigned int cclk_vlev_datasheet[] = { + VRPAIR(VLEV_100, 400000000), + VRPAIR(VLEV_105, 426000000), + VRPAIR(VLEV_110, 500000000), + VRPAIR(VLEV_115, 533000000), + VRPAIR(VLEV_120, 600000000), +}; + +static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = { + .tuple_tab = cclk_vlev_datasheet, + .tabsize = ARRAY_SIZE(cclk_vlev_datasheet), + .vr_settling_time = 25 /* us */, +}; + +static struct platform_device bfin_dpmc = { + .name = "bfin dpmc", + .dev = { + .platform_data = &bfin_dmpc_vreg_data, + }, +}; + +static struct platform_device *tll6527m_devices[] __initdata = { + + &bfin_dpmc, + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE) + &musb_device, +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) + &bfin_mii_bus, + &bfin_mac_device, +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &bfin_spi0_device, +#endif + +#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE) + &bfin_lq035q1_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + &bfin_uart1_device, +#endif +#endif + +#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) +#ifdef CONFIG_BFIN_SIR0 + &bfin_sir0_device, +#endif +#ifdef CONFIG_BFIN_SIR1 + &bfin_sir1_device, +#endif +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) + &i2c_bfin_twi_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) \ + || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART + &bfin_sport0_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART + &bfin_sport1_uart_device, +#endif +#endif + +#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) + &tll6527m_flash_device, +#endif + +#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) + &bfin_i2s, +#endif + +#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE) + &spi_decoded_gpio, +#endif +}; + +static int __init tll6527m_init(void) +{ + printk(KERN_INFO "%s(): registering device resources\n", __func__); + i2c_register_board_info(0, bfin_i2c_board_info, + ARRAY_SIZE(bfin_i2c_board_info)); + platform_add_devices(tll6527m_devices, ARRAY_SIZE(tll6527m_devices)); + spi_register_board_info(bfin_spi_board_info, + ARRAY_SIZE(bfin_spi_board_info)); + return 0; +} + +arch_initcall(tll6527m_init); + +static struct platform_device *tll6527m_early_devices[] __initdata = { +#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK) +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + &bfin_uart1_device, +#endif +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE) +#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART + &bfin_sport0_uart_device, +#endif +#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART + &bfin_sport1_uart_device, +#endif +#endif +}; + +void __init native_machine_early_platform_add_devices(void) +{ + printk(KERN_INFO "register early platform devices\n"); + early_platform_add_devices(tll6527m_early_devices, + ARRAY_SIZE(tll6527m_early_devices)); +} + +void native_machine_restart(char *cmd) +{ + /* workaround reboot hang when booting from SPI */ + if ((bfin_read_SYSCR() & 0x7) == 0x3) + bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS); +} + +void bfin_get_ether_addr(char *addr) +{ + /* the MAC is stored in OTP memory page 0xDF */ + u32 ret; + u64 otp_mac; + u32 (*otp_read)(u32 page, u32 flags, + u64 *page_content) = (void *)0xEF00001A; + + ret = otp_read(0xDF, 0x00, &otp_mac); + if (!(ret & 0x1)) { + char *otp_mac_p = (char *)&otp_mac; + for (ret = 0; ret < 6; ++ret) + addr[ret] = otp_mac_p[5 - ret]; + } +} +EXPORT_SYMBOL(bfin_get_ether_addr); -- cgit v1.1