From c9b74c5b8fb807187f6b1db09012828fcd2d7e73 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Fri, 18 Apr 2008 20:41:49 +0200 Subject: sdhci: don't check block count for progress The specification is insufficiently strict when it comes to how the hardware should update the block count register, making it useless for checking transfer progress. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci.c | 23 +++++++++-------------- 1 file changed, 9 insertions(+), 14 deletions(-) diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index b413aa6..9b06c60 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -567,7 +567,6 @@ static void sdhci_set_transfer_mode(struct sdhci_host *host, static void sdhci_finish_data(struct sdhci_host *host) { struct mmc_data *data; - u16 blocks; BUG_ON(!host->data); @@ -580,20 +579,16 @@ static void sdhci_finish_data(struct sdhci_host *host) } /* - * Controller doesn't count down when in single block mode. + * The specification states that the block count register must + * be updated, but it does not specify at what point in the + * data flow. That makes the register entirely useless to read + * back so we have to assume that nothing made it to the card + * in the event of an error. */ - if (data->blocks == 1) - blocks = (data->error == 0) ? 0 : 1; + if (data->error) + data->bytes_xfered = 0; else - blocks = readw(host->ioaddr + SDHCI_BLOCK_COUNT); - data->bytes_xfered = data->blksz * (data->blocks - blocks); - - if (!data->error && blocks) { - printk(KERN_ERR "%s: Controller signalled completion even " - "though there were blocks left.\n", - mmc_hostname(host->mmc)); - data->error = -EIO; - } + data->bytes_xfered = data->blksz * data->blocks; if (data->stop) { /* @@ -1466,7 +1461,7 @@ static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot) mmc->ops = &sdhci_ops; mmc->f_min = host->max_clk / 256; mmc->f_max = host->max_clk; - mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE | MMC_CAP_SDIO_IRQ; + mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ; if (caps & SDHCI_CAN_DO_HISPD) mmc->caps |= MMC_CAP_SD_HIGHSPEED; -- cgit v1.1 From b8c86fc5d8deaa5a6dc49c2c1ed144e6838bf0f3 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Tue, 18 Mar 2008 17:35:49 +0100 Subject: sdhci: move pci stuff to separate module The SDHCI interface is not PCI specific, yet the Linux driver was intimitely connected to the PCI bus. This patch properly separates the PCI specific portion from the bus independent code. This patch is based on work by Ben Dooks but he did not have time to complete it. Signed-off-by: Pierre Ossman --- drivers/mmc/host/Kconfig | 19 +- drivers/mmc/host/Makefile | 1 + drivers/mmc/host/sdhci-pci.c | 486 +++++++++++++++++++++++++++++++++++++++++ drivers/mmc/host/sdhci.c | 499 ++++++++----------------------------------- drivers/mmc/host/sdhci.h | 82 ++++--- 5 files changed, 651 insertions(+), 436 deletions(-) create mode 100644 drivers/mmc/host/sdhci-pci.c diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index dead617..f9cbcb8 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -26,18 +26,31 @@ config MMC_PXA config MMC_SDHCI tristate "Secure Digital Host Controller Interface support" - depends on PCI + depends on HAS_DMA help - This select the generic Secure Digital Host Controller Interface. + This selects the generic Secure Digital Host Controller Interface. It is used by manufacturers such as Texas Instruments(R), Ricoh(R) and Toshiba(R). Most controllers found in laptops are of this type. + + If you have a controller with this interface, say Y or M here. You + also need to enable an appropriate bus interface. + + If unsure, say N. + +config MMC_SDHCI_PCI + tristate "SDHCI support on PCI bus" + depends on MMC_SDHCI && PCI + help + This selects the PCI Secure Digital Host Controller Interface. + Most controllers found today are PCI devices. + If you have a controller with this interface, say Y or M here. If unsure, say N. config MMC_RICOH_MMC tristate "Ricoh MMC Controller Disabler (EXPERIMENTAL)" - depends on PCI && EXPERIMENTAL && MMC_SDHCI + depends on MMC_SDHCI_PCI help This selects the disabler for the Ricoh MMC Controller. This proprietary controller is unnecessary because the SDHCI driver diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index 3877c87..3027250 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_MMC_ARMMMCI) += mmci.o obj-$(CONFIG_MMC_PXA) += pxamci.o obj-$(CONFIG_MMC_IMX) += imxmmc.o obj-$(CONFIG_MMC_SDHCI) += sdhci.o +obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o obj-$(CONFIG_MMC_RICOH_MMC) += ricoh_mmc.o obj-$(CONFIG_MMC_WBSD) += wbsd.o obj-$(CONFIG_MMC_AU1X) += au1xmmc.o diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c new file mode 100644 index 0000000..2a3dd6c --- /dev/null +++ b/drivers/mmc/host/sdhci-pci.c @@ -0,0 +1,486 @@ +/* linux/drivers/mmc/host/sdhci-pci.c - SDHCI on PCI bus interface + * + * Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or (at + * your option) any later version. + * + * Thanks to the following companies for their support: + * + * - JMicron (hardware and technical support) + */ + +#include +#include +#include +#include + +#include + +#include +#include + +#include "sdhci.h" + +/* + * PCI registers + */ + +#define PCI_SDHCI_IFPIO 0x00 +#define PCI_SDHCI_IFDMA 0x01 +#define PCI_SDHCI_IFVENDOR 0x02 + +#define PCI_SLOT_INFO 0x40 /* 8 bits */ +#define PCI_SLOT_INFO_SLOTS(x) ((x >> 4) & 7) +#define PCI_SLOT_INFO_FIRST_BAR_MASK 0x07 + +#define MAX_SLOTS 8 + +static const struct pci_device_id pci_ids[] __devinitdata = { + { + .vendor = PCI_VENDOR_ID_RICOH, + .device = PCI_DEVICE_ID_RICOH_R5C822, + .subvendor = PCI_VENDOR_ID_IBM, + .subdevice = PCI_ANY_ID, + .driver_data = SDHCI_QUIRK_CLOCK_BEFORE_RESET | + SDHCI_QUIRK_FORCE_DMA, + }, + + { + .vendor = PCI_VENDOR_ID_RICOH, + .device = PCI_DEVICE_ID_RICOH_R5C822, + .subvendor = PCI_VENDOR_ID_SAMSUNG, + .subdevice = PCI_ANY_ID, + .driver_data = SDHCI_QUIRK_FORCE_DMA | + SDHCI_QUIRK_NO_CARD_NO_RESET, + }, + + { + .vendor = PCI_VENDOR_ID_RICOH, + .device = PCI_DEVICE_ID_RICOH_R5C822, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = SDHCI_QUIRK_FORCE_DMA, + }, + + { + .vendor = PCI_VENDOR_ID_TI, + .device = PCI_DEVICE_ID_TI_XX21_XX11_SD, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = SDHCI_QUIRK_FORCE_DMA, + }, + + { + .vendor = PCI_VENDOR_ID_ENE, + .device = PCI_DEVICE_ID_ENE_CB712_SD, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | + SDHCI_QUIRK_BROKEN_DMA, + }, + + { + .vendor = PCI_VENDOR_ID_ENE, + .device = PCI_DEVICE_ID_ENE_CB712_SD_2, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | + SDHCI_QUIRK_BROKEN_DMA, + }, + + { + .vendor = PCI_VENDOR_ID_ENE, + .device = PCI_DEVICE_ID_ENE_CB714_SD, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | + SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS | + SDHCI_QUIRK_BROKEN_DMA, + }, + + { + .vendor = PCI_VENDOR_ID_ENE, + .device = PCI_DEVICE_ID_ENE_CB714_SD_2, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | + SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS | + SDHCI_QUIRK_BROKEN_DMA, + }, + + { + .vendor = PCI_VENDOR_ID_MARVELL, + .device = PCI_DEVICE_ID_MARVELL_CAFE_SD, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER | + SDHCI_QUIRK_INCR_TIMEOUT_CONTROL, + }, + + { + .vendor = PCI_VENDOR_ID_JMICRON, + .device = PCI_DEVICE_ID_JMICRON_JMB38X_SD, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = SDHCI_QUIRK_32BIT_DMA_ADDR | + SDHCI_QUIRK_32BIT_DMA_SIZE | + SDHCI_QUIRK_RESET_AFTER_REQUEST, + }, + + { /* Generic SD host controller */ + PCI_DEVICE_CLASS((PCI_CLASS_SYSTEM_SDHCI << 8), 0xFFFF00) + }, + + { /* end: all zeroes */ }, +}; + +MODULE_DEVICE_TABLE(pci, pci_ids); + +struct sdhci_pci_chip; + +struct sdhci_pci_slot { + struct sdhci_pci_chip *chip; + struct sdhci_host *host; + + int pci_bar; +}; + +struct sdhci_pci_chip { + struct pci_dev *pdev; + unsigned int quirks; + + int num_slots; /* Slots on controller */ + struct sdhci_pci_slot *slots[MAX_SLOTS]; /* Pointers to host slots */ +}; + +/*****************************************************************************\ + * * + * SDHCI core callbacks * + * * +\*****************************************************************************/ + +static int sdhci_pci_enable_dma(struct sdhci_host *host) +{ + struct sdhci_pci_slot *slot; + struct pci_dev *pdev; + int ret; + + slot = sdhci_priv(host); + pdev = slot->chip->pdev; + + if (((pdev->class & 0xFFFF00) == (PCI_CLASS_SYSTEM_SDHCI << 8)) && + ((pdev->class & 0x0000FF) != PCI_SDHCI_IFDMA) && + (host->flags & SDHCI_USE_DMA)) { + dev_warn(&pdev->dev, "Will use DMA mode even though HW " + "doesn't fully claim to support it.\n"); + } + + ret = pci_set_dma_mask(pdev, DMA_32BIT_MASK); + if (ret) + return ret; + + pci_set_master(pdev); + + return 0; +} + +static struct sdhci_ops sdhci_pci_ops = { + .enable_dma = sdhci_pci_enable_dma, +}; + +/*****************************************************************************\ + * * + * Suspend/resume * + * * +\*****************************************************************************/ + +#ifdef CONFIG_PM + +static int sdhci_pci_suspend (struct pci_dev *pdev, pm_message_t state) +{ + struct sdhci_pci_chip *chip; + struct sdhci_pci_slot *slot; + int i, ret; + + chip = pci_get_drvdata(pdev); + if (!chip) + return 0; + + for (i = 0;i < chip->num_slots;i++) { + slot = chip->slots[i]; + if (!slot) + continue; + + ret = sdhci_suspend_host(slot->host, state); + + if (ret) { + for (i--;i >= 0;i--) + sdhci_resume_host(chip->slots[i]->host); + return ret; + } + } + + pci_save_state(pdev); + pci_enable_wake(pdev, pci_choose_state(pdev, state), 0); + pci_disable_device(pdev); + pci_set_power_state(pdev, pci_choose_state(pdev, state)); + + return 0; +} + +static int sdhci_pci_resume (struct pci_dev *pdev) +{ + struct sdhci_pci_chip *chip; + struct sdhci_pci_slot *slot; + int i, ret; + + chip = pci_get_drvdata(pdev); + if (!chip) + return 0; + + pci_set_power_state(pdev, PCI_D0); + pci_restore_state(pdev); + ret = pci_enable_device(pdev); + if (ret) + return ret; + + for (i = 0;i < chip->num_slots;i++) { + slot = chip->slots[i]; + if (!slot) + continue; + + ret = sdhci_resume_host(slot->host); + if (ret) + return ret; + } + + return 0; +} + +#else /* CONFIG_PM */ + +#define sdhci_pci_suspend NULL +#define sdhci_pci_resume NULL + +#endif /* CONFIG_PM */ + +/*****************************************************************************\ + * * + * Device probing/removal * + * * +\*****************************************************************************/ + +static struct sdhci_pci_slot * __devinit sdhci_pci_probe_slot( + struct pci_dev *pdev, struct sdhci_pci_chip *chip, int bar) +{ + struct sdhci_pci_slot *slot; + struct sdhci_host *host; + + resource_size_t addr; + + int ret; + + if (!(pci_resource_flags(pdev, bar) & IORESOURCE_MEM)) { + dev_err(&pdev->dev, "BAR %d is not iomem. Aborting.\n", bar); + return ERR_PTR(-ENODEV); + } + + if (pci_resource_len(pdev, bar) != 0x100) { + dev_err(&pdev->dev, "Invalid iomem size. You may " + "experience problems.\n"); + } + + if ((pdev->class & 0x0000FF) == PCI_SDHCI_IFVENDOR) { + dev_err(&pdev->dev, "Vendor specific interface. Aborting.\n"); + return ERR_PTR(-ENODEV); + } + + if ((pdev->class & 0x0000FF) > PCI_SDHCI_IFVENDOR) { + dev_err(&pdev->dev, "Unknown interface. Aborting.\n"); + return ERR_PTR(-ENODEV); + } + + host = sdhci_alloc_host(&pdev->dev, sizeof(struct sdhci_pci_slot)); + if (IS_ERR(host)) { + ret = PTR_ERR(host); + goto unmap; + } + + slot = sdhci_priv(host); + + slot->chip = chip; + slot->host = host; + slot->pci_bar = bar; + + host->hw_name = "PCI"; + host->ops = &sdhci_pci_ops; + host->quirks = chip->quirks; + + host->irq = pdev->irq; + + ret = pci_request_region(pdev, bar, mmc_hostname(host->mmc)); + if (ret) { + dev_err(&pdev->dev, "cannot request region\n"); + return ERR_PTR(ret); + } + + addr = pci_resource_start(pdev, bar); + host->ioaddr = ioremap_nocache(addr, pci_resource_len(pdev, bar)); + if (!host->ioaddr) { + dev_err(&pdev->dev, "failed to remap registers\n"); + goto release; + } + + ret = sdhci_add_host(host); + if (ret) + goto unmap; + + return slot; + +unmap: + iounmap(host->ioaddr); + +release: + pci_release_region(pdev, bar); + sdhci_free_host(host); + + return ERR_PTR(ret); +} + +static void sdhci_pci_remove_slot(struct sdhci_pci_slot *slot) +{ + sdhci_remove_host(slot->host); + pci_release_region(slot->chip->pdev, slot->pci_bar); + sdhci_free_host(slot->host); +} + +static int __devinit sdhci_pci_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + struct sdhci_pci_chip *chip; + struct sdhci_pci_slot *slot; + + u8 slots, rev, first_bar; + int ret, i; + + BUG_ON(pdev == NULL); + BUG_ON(ent == NULL); + + pci_read_config_byte(pdev, PCI_CLASS_REVISION, &rev); + + dev_info(&pdev->dev, "SDHCI controller found [%04x:%04x] (rev %x)\n", + (int)pdev->vendor, (int)pdev->device, (int)rev); + + ret = pci_read_config_byte(pdev, PCI_SLOT_INFO, &slots); + if (ret) + return ret; + + slots = PCI_SLOT_INFO_SLOTS(slots) + 1; + dev_dbg(&pdev->dev, "found %d slot(s)\n", slots); + if (slots == 0) + return -ENODEV; + + BUG_ON(slots > MAX_SLOTS); + + ret = pci_read_config_byte(pdev, PCI_SLOT_INFO, &first_bar); + if (ret) + return ret; + + first_bar &= PCI_SLOT_INFO_FIRST_BAR_MASK; + + if (first_bar > 5) { + dev_err(&pdev->dev, "Invalid first BAR. Aborting.\n"); + return -ENODEV; + } + + ret = pci_enable_device(pdev); + if (ret) + return ret; + + chip = kzalloc(sizeof(struct sdhci_pci_chip), GFP_KERNEL); + if (!chip) { + ret = -ENOMEM; + goto err; + } + + chip->pdev = pdev; + chip->quirks = ent->driver_data; + chip->num_slots = slots; + + pci_set_drvdata(pdev, chip); + + for (i = 0;i < slots;i++) { + slot = sdhci_pci_probe_slot(pdev, chip, first_bar + i); + if (IS_ERR(slot)) { + for (i--;i >= 0;i--) + sdhci_pci_remove_slot(chip->slots[i]); + ret = PTR_ERR(slot); + goto free; + } + + chip->slots[i] = slot; + } + + return 0; + +free: + pci_set_drvdata(pdev, NULL); + kfree(chip); + +err: + pci_disable_device(pdev); + return ret; +} + +static void __devexit sdhci_pci_remove(struct pci_dev *pdev) +{ + int i; + struct sdhci_pci_chip *chip; + + chip = pci_get_drvdata(pdev); + + if (chip) { + for (i = 0;i < chip->num_slots; i++) + sdhci_pci_remove_slot(chip->slots[i]); + + pci_set_drvdata(pdev, NULL); + kfree(chip); + } + + pci_disable_device(pdev); +} + +static struct pci_driver sdhci_driver = { + .name = "sdhci-pci", + .id_table = pci_ids, + .probe = sdhci_pci_probe, + .remove = __devexit_p(sdhci_pci_remove), + .suspend = sdhci_pci_suspend, + .resume = sdhci_pci_resume, +}; + +/*****************************************************************************\ + * * + * Driver init/exit * + * * +\*****************************************************************************/ + +static int __init sdhci_drv_init(void) +{ + return pci_register_driver(&sdhci_driver); +} + +static void __exit sdhci_drv_exit(void) +{ + pci_unregister_driver(&sdhci_driver); +} + +module_init(sdhci_drv_init); +module_exit(sdhci_drv_exit); + +MODULE_AUTHOR("Pierre Ossman "); +MODULE_DESCRIPTION("Secure Digital Host Controller Interface PCI driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 9b06c60..8ce01d4 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -15,7 +15,7 @@ #include #include -#include +#include #include #include @@ -32,135 +32,6 @@ static unsigned int debug_quirks = 0; -/* - * Different quirks to handle when the hardware deviates from a strict - * interpretation of the SDHCI specification. - */ - -/* Controller doesn't honor resets unless we touch the clock register */ -#define SDHCI_QUIRK_CLOCK_BEFORE_RESET (1<<0) -/* Controller has bad caps bits, but really supports DMA */ -#define SDHCI_QUIRK_FORCE_DMA (1<<1) -/* Controller doesn't like to be reset when there is no card inserted. */ -#define SDHCI_QUIRK_NO_CARD_NO_RESET (1<<2) -/* Controller doesn't like clearing the power reg before a change */ -#define SDHCI_QUIRK_SINGLE_POWER_WRITE (1<<3) -/* Controller has flaky internal state so reset it on each ios change */ -#define SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS (1<<4) -/* Controller has an unusable DMA engine */ -#define SDHCI_QUIRK_BROKEN_DMA (1<<5) -/* Controller can only DMA from 32-bit aligned addresses */ -#define SDHCI_QUIRK_32BIT_DMA_ADDR (1<<6) -/* Controller can only DMA chunk sizes that are a multiple of 32 bits */ -#define SDHCI_QUIRK_32BIT_DMA_SIZE (1<<7) -/* Controller needs to be reset after each request to stay stable */ -#define SDHCI_QUIRK_RESET_AFTER_REQUEST (1<<8) -/* Controller needs voltage and power writes to happen separately */ -#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<9) -/* Controller has an off-by-one issue with timeout value */ -#define SDHCI_QUIRK_INCR_TIMEOUT_CONTROL (1<<10) - -static const struct pci_device_id pci_ids[] __devinitdata = { - { - .vendor = PCI_VENDOR_ID_RICOH, - .device = PCI_DEVICE_ID_RICOH_R5C822, - .subvendor = PCI_VENDOR_ID_IBM, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_CLOCK_BEFORE_RESET | - SDHCI_QUIRK_FORCE_DMA, - }, - - { - .vendor = PCI_VENDOR_ID_RICOH, - .device = PCI_DEVICE_ID_RICOH_R5C822, - .subvendor = PCI_VENDOR_ID_SAMSUNG, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_FORCE_DMA | - SDHCI_QUIRK_NO_CARD_NO_RESET, - }, - - { - .vendor = PCI_VENDOR_ID_RICOH, - .device = PCI_DEVICE_ID_RICOH_R5C822, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_FORCE_DMA, - }, - - { - .vendor = PCI_VENDOR_ID_TI, - .device = PCI_DEVICE_ID_TI_XX21_XX11_SD, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_FORCE_DMA, - }, - - { - .vendor = PCI_VENDOR_ID_ENE, - .device = PCI_DEVICE_ID_ENE_CB712_SD, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | - SDHCI_QUIRK_BROKEN_DMA, - }, - - { - .vendor = PCI_VENDOR_ID_ENE, - .device = PCI_DEVICE_ID_ENE_CB712_SD_2, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | - SDHCI_QUIRK_BROKEN_DMA, - }, - - { - .vendor = PCI_VENDOR_ID_ENE, - .device = PCI_DEVICE_ID_ENE_CB714_SD, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | - SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS | - SDHCI_QUIRK_BROKEN_DMA, - }, - - { - .vendor = PCI_VENDOR_ID_ENE, - .device = PCI_DEVICE_ID_ENE_CB714_SD_2, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | - SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS | - SDHCI_QUIRK_BROKEN_DMA, - }, - - { - .vendor = PCI_VENDOR_ID_MARVELL, - .device = PCI_DEVICE_ID_MARVELL_CAFE_SD, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER | - SDHCI_QUIRK_INCR_TIMEOUT_CONTROL, - }, - - { - .vendor = PCI_VENDOR_ID_JMICRON, - .device = PCI_DEVICE_ID_JMICRON_JMB38X_SD, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_32BIT_DMA_ADDR | - SDHCI_QUIRK_32BIT_DMA_SIZE | - SDHCI_QUIRK_RESET_AFTER_REQUEST, - }, - - { /* Generic SD host controller */ - PCI_DEVICE_CLASS((PCI_CLASS_SYSTEM_SDHCI << 8), 0xFFFF00) - }, - - { /* end: all zeroes */ }, -}; - -MODULE_DEVICE_TABLE(pci, pci_ids); - static void sdhci_prepare_data(struct sdhci_host *, struct mmc_data *); static void sdhci_finish_data(struct sdhci_host *); @@ -215,7 +86,7 @@ static void sdhci_reset(struct sdhci_host *host, u8 mask) { unsigned long timeout; - if (host->chip->quirks & SDHCI_QUIRK_NO_CARD_NO_RESET) { + if (host->quirks & SDHCI_QUIRK_NO_CARD_NO_RESET) { if (!(readl(host->ioaddr + SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT)) return; @@ -488,7 +359,7 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) * Compensate for an off-by-one error in the CaFe hardware; otherwise, * a too-small count gives us interrupt timeouts. */ - if ((host->chip->quirks & SDHCI_QUIRK_INCR_TIMEOUT_CONTROL)) + if ((host->quirks & SDHCI_QUIRK_INCR_TIMEOUT_CONTROL)) count++; if (count >= 0xF) { @@ -503,7 +374,7 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) host->flags |= SDHCI_REQ_USE_DMA; if (unlikely((host->flags & SDHCI_REQ_USE_DMA) && - (host->chip->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE) && + (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE) && ((data->blksz * data->blocks) & 0x3))) { DBG("Reverting to PIO because of transfer size (%d)\n", data->blksz * data->blocks); @@ -515,7 +386,7 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) * translation to device address space. */ if (unlikely((host->flags & SDHCI_REQ_USE_DMA) && - (host->chip->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) && + (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) && (data->sg->offset & 0x3))) { DBG("Reverting to PIO because of bad alignment\n"); host->flags &= ~SDHCI_REQ_USE_DMA; @@ -524,11 +395,13 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) if (host->flags & SDHCI_REQ_USE_DMA) { int count; - count = pci_map_sg(host->chip->pdev, data->sg, data->sg_len, - (data->flags & MMC_DATA_READ)?PCI_DMA_FROMDEVICE:PCI_DMA_TODEVICE); - BUG_ON(count != 1); + count = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len, + (data->flags & MMC_DATA_READ) ? + DMA_FROM_DEVICE : DMA_TO_DEVICE); + WARN_ON(count != 1); - writel(sg_dma_address(data->sg), host->ioaddr + SDHCI_DMA_ADDRESS); + writel(sg_dma_address(data->sg), + host->ioaddr + SDHCI_DMA_ADDRESS); } else { host->cur_sg = data->sg; host->num_sg = data->sg_len; @@ -574,8 +447,9 @@ static void sdhci_finish_data(struct sdhci_host *host) host->data = NULL; if (host->flags & SDHCI_REQ_USE_DMA) { - pci_unmap_sg(host->chip->pdev, data->sg, data->sg_len, - (data->flags & MMC_DATA_READ)?PCI_DMA_FROMDEVICE:PCI_DMA_TODEVICE); + dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, + (data->flags & MMC_DATA_READ) ? + DMA_FROM_DEVICE : DMA_TO_DEVICE); } /* @@ -770,7 +644,7 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned short power) * Spec says that we should clear the power reg before setting * a new value. Some controllers don't seem to like this though. */ - if (!(host->chip->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE)) + if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE)) writeb(0, host->ioaddr + SDHCI_POWER_CONTROL); pwr = SDHCI_POWER_ON; @@ -795,7 +669,7 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned short power) * At least the CaFe chip gets confused if we set the voltage * and set turn on power at the same time, so set the voltage first. */ - if ((host->chip->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER)) + if ((host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER)) writeb(pwr & ~SDHCI_POWER_ON, host->ioaddr + SDHCI_POWER_CONTROL); @@ -883,7 +757,7 @@ static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) * signalling timeout and CRC errors even on CMD0. Resetting * it on each ios seems to solve the problem. */ - if(host->chip->quirks & SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS) + if(host->quirks & SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS) sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA); mmiowb(); @@ -994,10 +868,10 @@ static void sdhci_tasklet_finish(unsigned long param) if (mrq->cmd->error || (mrq->data && (mrq->data->error || (mrq->data->stop && mrq->data->stop->error))) || - (host->chip->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST)) { + (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST)) { /* Some controllers need this kick or reset won't work here */ - if (host->chip->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET) { + if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET) { unsigned int clock; /* This is to force an update */ @@ -1229,165 +1103,90 @@ out: #ifdef CONFIG_PM -static int sdhci_suspend (struct pci_dev *pdev, pm_message_t state) +int sdhci_suspend_host(struct sdhci_host *host, pm_message_t state) { - struct sdhci_chip *chip; - int i, ret; - - chip = pci_get_drvdata(pdev); - if (!chip) - return 0; - - DBG("Suspending...\n"); - - for (i = 0;i < chip->num_slots;i++) { - if (!chip->hosts[i]) - continue; - ret = mmc_suspend_host(chip->hosts[i]->mmc, state); - if (ret) { - for (i--;i >= 0;i--) - mmc_resume_host(chip->hosts[i]->mmc); - return ret; - } - } - - pci_save_state(pdev); - pci_enable_wake(pdev, pci_choose_state(pdev, state), 0); + int ret; - for (i = 0;i < chip->num_slots;i++) { - if (!chip->hosts[i]) - continue; - free_irq(chip->hosts[i]->irq, chip->hosts[i]); - } + ret = mmc_suspend_host(host->mmc, state); + if (ret) + return ret; - pci_disable_device(pdev); - pci_set_power_state(pdev, pci_choose_state(pdev, state)); + free_irq(host->irq, host); return 0; } -static int sdhci_resume (struct pci_dev *pdev) -{ - struct sdhci_chip *chip; - int i, ret; +EXPORT_SYMBOL_GPL(sdhci_suspend_host); - chip = pci_get_drvdata(pdev); - if (!chip) - return 0; +int sdhci_resume_host(struct sdhci_host *host) +{ + int ret; - DBG("Resuming...\n"); + if (host->flags & SDHCI_USE_DMA) { + if (host->ops->enable_dma) + host->ops->enable_dma(host); + } - pci_set_power_state(pdev, PCI_D0); - pci_restore_state(pdev); - ret = pci_enable_device(pdev); + ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED, + mmc_hostname(host->mmc), host); if (ret) return ret; - for (i = 0;i < chip->num_slots;i++) { - if (!chip->hosts[i]) - continue; - if (chip->hosts[i]->flags & SDHCI_USE_DMA) - pci_set_master(pdev); - ret = request_irq(chip->hosts[i]->irq, sdhci_irq, - IRQF_SHARED, mmc_hostname(chip->hosts[i]->mmc), - chip->hosts[i]); - if (ret) - return ret; - sdhci_init(chip->hosts[i]); - mmiowb(); - ret = mmc_resume_host(chip->hosts[i]->mmc); - if (ret) - return ret; - } + sdhci_init(host); + mmiowb(); + + ret = mmc_resume_host(host->mmc); + if (ret) + return ret; return 0; } -#else /* CONFIG_PM */ - -#define sdhci_suspend NULL -#define sdhci_resume NULL +EXPORT_SYMBOL_GPL(sdhci_resume_host); #endif /* CONFIG_PM */ /*****************************************************************************\ * * - * Device probing/removal * + * Device allocation/registration * * * \*****************************************************************************/ -static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot) +struct sdhci_host *sdhci_alloc_host(struct device *dev, + size_t priv_size) { - int ret; - unsigned int version; - struct sdhci_chip *chip; struct mmc_host *mmc; struct sdhci_host *host; - u8 first_bar; - unsigned int caps; - - chip = pci_get_drvdata(pdev); - BUG_ON(!chip); - - ret = pci_read_config_byte(pdev, PCI_SLOT_INFO, &first_bar); - if (ret) - return ret; - - first_bar &= PCI_SLOT_INFO_FIRST_BAR_MASK; + WARN_ON(dev == NULL); - if (first_bar > 5) { - printk(KERN_ERR DRIVER_NAME ": Invalid first BAR. Aborting.\n"); - return -ENODEV; - } - - if (!(pci_resource_flags(pdev, first_bar + slot) & IORESOURCE_MEM)) { - printk(KERN_ERR DRIVER_NAME ": BAR is not iomem. Aborting.\n"); - return -ENODEV; - } - - if (pci_resource_len(pdev, first_bar + slot) != 0x100) { - printk(KERN_ERR DRIVER_NAME ": Invalid iomem size. " - "You may experience problems.\n"); - } - - if ((pdev->class & 0x0000FF) == PCI_SDHCI_IFVENDOR) { - printk(KERN_ERR DRIVER_NAME ": Vendor specific interface. Aborting.\n"); - return -ENODEV; - } - - if ((pdev->class & 0x0000FF) > PCI_SDHCI_IFVENDOR) { - printk(KERN_ERR DRIVER_NAME ": Unknown interface. Aborting.\n"); - return -ENODEV; - } - - mmc = mmc_alloc_host(sizeof(struct sdhci_host), &pdev->dev); + mmc = mmc_alloc_host(sizeof(struct sdhci_host) + priv_size, dev); if (!mmc) - return -ENOMEM; + return ERR_PTR(-ENOMEM); host = mmc_priv(mmc); host->mmc = mmc; - host->chip = chip; - chip->hosts[slot] = host; + return host; +} - host->bar = first_bar + slot; +EXPORT_SYMBOL_GPL(sdhci_alloc_host); - host->addr = pci_resource_start(pdev, host->bar); - host->irq = pdev->irq; +int sdhci_add_host(struct sdhci_host *host) +{ + struct mmc_host *mmc; + unsigned int caps; + unsigned int version; + int ret; - DBG("slot %d at 0x%08lx, irq %d\n", slot, host->addr, host->irq); + WARN_ON(host == NULL); + if (host == NULL) + return -EINVAL; - ret = pci_request_region(pdev, host->bar, mmc_hostname(mmc)); - if (ret) - goto free; + mmc = host->mmc; - host->ioaddr = ioremap_nocache(host->addr, - pci_resource_len(pdev, host->bar)); - if (!host->ioaddr) { - ret = -ENOMEM; - goto release; - } + if (debug_quirks) + host->quirks = debug_quirks; sdhci_reset(host, SDHCI_RESET_ALL); @@ -1401,46 +1200,40 @@ static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot) caps = readl(host->ioaddr + SDHCI_CAPABILITIES); - if (chip->quirks & SDHCI_QUIRK_FORCE_DMA) + if (host->quirks & SDHCI_QUIRK_FORCE_DMA) host->flags |= SDHCI_USE_DMA; else if (!(caps & SDHCI_CAN_DO_DMA)) DBG("Controller doesn't have DMA capability\n"); else host->flags |= SDHCI_USE_DMA; - if ((chip->quirks & SDHCI_QUIRK_BROKEN_DMA) && + if ((host->quirks & SDHCI_QUIRK_BROKEN_DMA) && (host->flags & SDHCI_USE_DMA)) { DBG("Disabling DMA as it is marked broken\n"); host->flags &= ~SDHCI_USE_DMA; } - if (((pdev->class & 0x0000FF) != PCI_SDHCI_IFDMA) && - (host->flags & SDHCI_USE_DMA)) { - printk(KERN_WARNING "%s: Will use DMA " - "mode even though HW doesn't fully " - "claim to support it.\n", mmc_hostname(mmc)); - } - if (host->flags & SDHCI_USE_DMA) { - if (pci_set_dma_mask(pdev, DMA_32BIT_MASK)) { - printk(KERN_WARNING "%s: No suitable DMA available. " - "Falling back to PIO.\n", mmc_hostname(mmc)); - host->flags &= ~SDHCI_USE_DMA; + if (host->ops->enable_dma) { + if (host->ops->enable_dma(host)) { + printk(KERN_WARNING "%s: No suitable DMA " + "available. Falling back to PIO.\n", + mmc_hostname(mmc)); + host->flags &= ~SDHCI_USE_DMA; + } } } - if (host->flags & SDHCI_USE_DMA) - pci_set_master(pdev); - else /* XXX: Hack to get MMC layer to avoid highmem */ - pdev->dma_mask = 0; + /* XXX: Hack to get MMC layer to avoid highmem */ + if (!(host->flags & SDHCI_USE_DMA)) + mmc_dev(host->mmc)->dma_mask = 0; host->max_clk = (caps & SDHCI_CLOCK_BASE_MASK) >> SDHCI_CLOCK_BASE_SHIFT; if (host->max_clk == 0) { printk(KERN_ERR "%s: Hardware doesn't specify base clock " "frequency.\n", mmc_hostname(mmc)); - ret = -ENODEV; - goto unmap; + return -ENODEV; } host->max_clk *= 1000000; @@ -1449,8 +1242,7 @@ static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot) if (host->timeout_clk == 0) { printk(KERN_ERR "%s: Hardware doesn't specify timeout clock " "frequency.\n", mmc_hostname(mmc)); - ret = -ENODEV; - goto unmap; + return -ENODEV; } if (caps & SDHCI_TIMEOUT_CLK_UNIT) host->timeout_clk *= 1000; @@ -1477,8 +1269,7 @@ static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot) if (mmc->ocr_avail == 0) { printk(KERN_ERR "%s: Hardware doesn't report any " "support voltages.\n", mmc_hostname(mmc)); - ret = -ENODEV; - goto unmap; + return -ENODEV; } spin_lock_init(&host->lock); @@ -1548,7 +1339,7 @@ static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot) host->led.default_trigger = mmc_hostname(mmc); host->led.brightness_set = sdhci_led_control; - ret = led_classdev_register(&pdev->dev, &host->led); + ret = led_classdev_register(mmc_dev(mmc), &host->led); if (ret) goto reset; #endif @@ -1557,8 +1348,8 @@ static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot) mmc_add_host(mmc); - printk(KERN_INFO "%s: SDHCI at 0x%08lx irq %d %s\n", - mmc_hostname(mmc), host->addr, host->irq, + printk(KERN_INFO "%s: SDHCI controller on %s [%s] using %s\n", + mmc_hostname(mmc), host->hw_name, mmc_dev(mmc)->bus_id, (host->flags & SDHCI_USE_DMA)?"DMA":"PIO"); return 0; @@ -1571,29 +1362,15 @@ reset: untasklet: tasklet_kill(&host->card_tasklet); tasklet_kill(&host->finish_tasklet); -unmap: - iounmap(host->ioaddr); -release: - pci_release_region(pdev, host->bar); -free: - mmc_free_host(mmc); return ret; } -static void sdhci_remove_slot(struct pci_dev *pdev, int slot) -{ - struct sdhci_chip *chip; - struct mmc_host *mmc; - struct sdhci_host *host; - - chip = pci_get_drvdata(pdev); - host = chip->hosts[slot]; - mmc = host->mmc; - - chip->hosts[slot] = NULL; +EXPORT_SYMBOL_GPL(sdhci_add_host); - mmc_remove_host(mmc); +void sdhci_remove_host(struct sdhci_host *host) +{ + mmc_remove_host(host->mmc); #ifdef CONFIG_LEDS_CLASS led_classdev_unregister(&host->led); @@ -1607,107 +1384,16 @@ static void sdhci_remove_slot(struct pci_dev *pdev, int slot) tasklet_kill(&host->card_tasklet); tasklet_kill(&host->finish_tasklet); - - iounmap(host->ioaddr); - - pci_release_region(pdev, host->bar); - - mmc_free_host(mmc); } -static int __devinit sdhci_probe(struct pci_dev *pdev, - const struct pci_device_id *ent) -{ - int ret, i; - u8 slots, rev; - struct sdhci_chip *chip; - - BUG_ON(pdev == NULL); - BUG_ON(ent == NULL); - - pci_read_config_byte(pdev, PCI_CLASS_REVISION, &rev); - - printk(KERN_INFO DRIVER_NAME - ": SDHCI controller found at %s [%04x:%04x] (rev %x)\n", - pci_name(pdev), (int)pdev->vendor, (int)pdev->device, - (int)rev); - - ret = pci_read_config_byte(pdev, PCI_SLOT_INFO, &slots); - if (ret) - return ret; - - slots = PCI_SLOT_INFO_SLOTS(slots) + 1; - DBG("found %d slot(s)\n", slots); - if (slots == 0) - return -ENODEV; +EXPORT_SYMBOL_GPL(sdhci_remove_host); - ret = pci_enable_device(pdev); - if (ret) - return ret; - - chip = kzalloc(sizeof(struct sdhci_chip) + - sizeof(struct sdhci_host*) * slots, GFP_KERNEL); - if (!chip) { - ret = -ENOMEM; - goto err; - } - - chip->pdev = pdev; - chip->quirks = ent->driver_data; - - if (debug_quirks) - chip->quirks = debug_quirks; - - chip->num_slots = slots; - pci_set_drvdata(pdev, chip); - - for (i = 0;i < slots;i++) { - ret = sdhci_probe_slot(pdev, i); - if (ret) { - for (i--;i >= 0;i--) - sdhci_remove_slot(pdev, i); - goto free; - } - } - - return 0; - -free: - pci_set_drvdata(pdev, NULL); - kfree(chip); - -err: - pci_disable_device(pdev); - return ret; -} - -static void __devexit sdhci_remove(struct pci_dev *pdev) +void sdhci_free_host(struct sdhci_host *host) { - int i; - struct sdhci_chip *chip; - - chip = pci_get_drvdata(pdev); - - if (chip) { - for (i = 0;i < chip->num_slots;i++) - sdhci_remove_slot(pdev, i); - - pci_set_drvdata(pdev, NULL); - - kfree(chip); - } - - pci_disable_device(pdev); + mmc_free_host(host->mmc); } -static struct pci_driver sdhci_driver = { - .name = DRIVER_NAME, - .id_table = pci_ids, - .probe = sdhci_probe, - .remove = __devexit_p(sdhci_remove), - .suspend = sdhci_suspend, - .resume = sdhci_resume, -}; +EXPORT_SYMBOL_GPL(sdhci_free_host); /*****************************************************************************\ * * @@ -1721,14 +1407,11 @@ static int __init sdhci_drv_init(void) ": Secure Digital Host Controller Interface driver\n"); printk(KERN_INFO DRIVER_NAME ": Copyright(c) Pierre Ossman\n"); - return pci_register_driver(&sdhci_driver); + return 0; } static void __exit sdhci_drv_exit(void) { - DBG("Exiting\n"); - - pci_unregister_driver(&sdhci_driver); } module_init(sdhci_drv_init); @@ -1737,7 +1420,7 @@ module_exit(sdhci_drv_exit); module_param(debug_quirks, uint, 0444); MODULE_AUTHOR("Pierre Ossman "); -MODULE_DESCRIPTION("Secure Digital Host Controller Interface driver"); +MODULE_DESCRIPTION("Secure Digital Host Controller Interface core driver"); MODULE_LICENSE("GPL"); MODULE_PARM_DESC(debug_quirks, "Force certain quirks."); diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 299118d..22fc258 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -10,18 +10,6 @@ */ /* - * PCI registers - */ - -#define PCI_SDHCI_IFPIO 0x00 -#define PCI_SDHCI_IFDMA 0x01 -#define PCI_SDHCI_IFVENDOR 0x02 - -#define PCI_SLOT_INFO 0x40 /* 8 bits */ -#define PCI_SLOT_INFO_SLOTS(x) ((x >> 4) & 7) -#define PCI_SLOT_INFO_FIRST_BAR_MASK 0x07 - -/* * Controller registers */ @@ -162,10 +150,43 @@ #define SDHCI_SPEC_VER_MASK 0x00FF #define SDHCI_SPEC_VER_SHIFT 0 -struct sdhci_chip; +struct sdhci_ops; struct sdhci_host { - struct sdhci_chip *chip; + /* Data set by hardware interface driver */ + const char *hw_name; /* Hardware bus name */ + + unsigned int quirks; /* Deviations from spec. */ + +/* Controller doesn't honor resets unless we touch the clock register */ +#define SDHCI_QUIRK_CLOCK_BEFORE_RESET (1<<0) +/* Controller has bad caps bits, but really supports DMA */ +#define SDHCI_QUIRK_FORCE_DMA (1<<1) +/* Controller doesn't like to be reset when there is no card inserted. */ +#define SDHCI_QUIRK_NO_CARD_NO_RESET (1<<2) +/* Controller doesn't like clearing the power reg before a change */ +#define SDHCI_QUIRK_SINGLE_POWER_WRITE (1<<3) +/* Controller has flaky internal state so reset it on each ios change */ +#define SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS (1<<4) +/* Controller has an unusable DMA engine */ +#define SDHCI_QUIRK_BROKEN_DMA (1<<5) +/* Controller can only DMA from 32-bit aligned addresses */ +#define SDHCI_QUIRK_32BIT_DMA_ADDR (1<<6) +/* Controller can only DMA chunk sizes that are a multiple of 32 bits */ +#define SDHCI_QUIRK_32BIT_DMA_SIZE (1<<7) +/* Controller needs to be reset after each request to stay stable */ +#define SDHCI_QUIRK_RESET_AFTER_REQUEST (1<<8) +/* Controller needs voltage and power writes to happen separately */ +#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<9) +/* Controller has an off-by-one issue with timeout value */ +#define SDHCI_QUIRK_INCR_TIMEOUT_CONTROL (1<<10) + + int irq; /* Device IRQ */ + void __iomem * ioaddr; /* Mapped address */ + + const struct sdhci_ops *ops; /* Low level hw interface */ + + /* Internal data */ struct mmc_host *mmc; /* MMC structure */ #ifdef CONFIG_LEDS_CLASS @@ -194,22 +215,33 @@ struct sdhci_host { int offset; /* Offset into current sg */ int remain; /* Bytes left in current */ - int irq; /* Device IRQ */ - int bar; /* PCI BAR index */ - unsigned long addr; /* Bus address */ - void __iomem * ioaddr; /* Mapped address */ - struct tasklet_struct card_tasklet; /* Tasklet structures */ struct tasklet_struct finish_tasklet; struct timer_list timer; /* Timer for timeouts */ -}; -struct sdhci_chip { - struct pci_dev *pdev; + unsigned long private[0] ____cacheline_aligned; +}; - unsigned long quirks; - int num_slots; /* Slots on controller */ - struct sdhci_host *hosts[0]; /* Pointers to hosts */ +struct sdhci_ops { + int (*enable_dma)(struct sdhci_host *host); }; + + +extern struct sdhci_host *sdhci_alloc_host(struct device *dev, + size_t priv_size); +extern void sdhci_free_host(struct sdhci_host *host); + +static inline void *sdhci_priv(struct sdhci_host *host) +{ + return (void *)host->private; +} + +extern int sdhci_add_host(struct sdhci_host *host); +extern void sdhci_remove_host(struct sdhci_host *host); + +#ifdef CONFIG_PM +extern int sdhci_suspend_host(struct sdhci_host *host, pm_message_t state); +extern int sdhci_resume_host(struct sdhci_host *host); +#endif -- cgit v1.1 From 3815a0ebab678c20d0d9c66af5ee9e68807b6681 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sat, 22 Mar 2008 22:05:40 +0100 Subject: sdhci: remove forced dma quirks Remove the quirk to force DMA on the Ricoh and TI controllers as it is no longer needed. The only bug they have is that they use an incorrect PCI interface value, and that is not respected anymore. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci-pci.c | 22 ++-------------------- 1 file changed, 2 insertions(+), 20 deletions(-) diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index 2a3dd6c..51798ec 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -44,8 +44,7 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .device = PCI_DEVICE_ID_RICOH_R5C822, .subvendor = PCI_VENDOR_ID_IBM, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_CLOCK_BEFORE_RESET | - SDHCI_QUIRK_FORCE_DMA, + .driver_data = SDHCI_QUIRK_CLOCK_BEFORE_RESET, }, { @@ -53,24 +52,7 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .device = PCI_DEVICE_ID_RICOH_R5C822, .subvendor = PCI_VENDOR_ID_SAMSUNG, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_FORCE_DMA | - SDHCI_QUIRK_NO_CARD_NO_RESET, - }, - - { - .vendor = PCI_VENDOR_ID_RICOH, - .device = PCI_DEVICE_ID_RICOH_R5C822, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_FORCE_DMA, - }, - - { - .vendor = PCI_VENDOR_ID_TI, - .device = PCI_DEVICE_ID_TI_XX21_XX11_SD, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_FORCE_DMA, + .driver_data = SDHCI_QUIRK_NO_CARD_NO_RESET, }, { -- cgit v1.1 From 22606405894a3ca5796eb4454a4b83af611fd201 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sun, 23 Mar 2008 19:33:23 +0100 Subject: sdhci: more complex quirks handling Extend the quirks handling in the PCI driver to be able to have callbacks and not just flags. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci-pci.c | 129 ++++++++++++++++++++++++++++--------------- 1 file changed, 86 insertions(+), 43 deletions(-) diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index 51798ec..5094fe8 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -38,21 +38,82 @@ #define MAX_SLOTS 8 -static const struct pci_device_id pci_ids[] __devinitdata = { - { - .vendor = PCI_VENDOR_ID_RICOH, - .device = PCI_DEVICE_ID_RICOH_R5C822, - .subvendor = PCI_VENDOR_ID_IBM, - .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_CLOCK_BEFORE_RESET, - }, +struct sdhci_pci_chip; + +struct sdhci_pci_fixes { + unsigned int quirks; + + int (*probe)(struct sdhci_pci_chip*); +}; + +struct sdhci_pci_slot { + struct sdhci_pci_chip *chip; + struct sdhci_host *host; + int pci_bar; +}; + +struct sdhci_pci_chip { + struct pci_dev *pdev; + + unsigned int quirks; + const struct sdhci_pci_fixes *fixes; + + int num_slots; /* Slots on controller */ + struct sdhci_pci_slot *slots[MAX_SLOTS]; /* Pointers to host slots */ +}; + + +/*****************************************************************************\ + * * + * Hardware specific quirk handling * + * * +\*****************************************************************************/ + +static int ricoh_probe(struct sdhci_pci_chip *chip) +{ + if (chip->pdev->subsystem_vendor == PCI_VENDOR_ID_IBM) + chip->quirks |= SDHCI_QUIRK_CLOCK_BEFORE_RESET; + + if (chip->pdev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG) + chip->quirks |= SDHCI_QUIRK_NO_CARD_NO_RESET; + + return 0; +} + +static const struct sdhci_pci_fixes sdhci_ricoh = { + .probe = ricoh_probe, +}; + +static const struct sdhci_pci_fixes sdhci_ene_712 = { + .quirks = SDHCI_QUIRK_SINGLE_POWER_WRITE | + SDHCI_QUIRK_BROKEN_DMA, +}; + +static const struct sdhci_pci_fixes sdhci_ene_714 = { + .quirks = SDHCI_QUIRK_SINGLE_POWER_WRITE | + SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS | + SDHCI_QUIRK_BROKEN_DMA, +}; + +static const struct sdhci_pci_fixes sdhci_cafe = { + .quirks = SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER | + SDHCI_QUIRK_INCR_TIMEOUT_CONTROL, +}; + +static const struct sdhci_pci_fixes sdhci_jmicron = { + .quirks = SDHCI_QUIRK_32BIT_DMA_ADDR | + SDHCI_QUIRK_32BIT_DMA_SIZE | + SDHCI_QUIRK_RESET_AFTER_REQUEST, +}; + +static const struct pci_device_id pci_ids[] __devinitdata = { { .vendor = PCI_VENDOR_ID_RICOH, .device = PCI_DEVICE_ID_RICOH_R5C822, - .subvendor = PCI_VENDOR_ID_SAMSUNG, + .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_NO_CARD_NO_RESET, + .driver_data = (kernel_ulong_t)&sdhci_ricoh, }, { @@ -60,8 +121,7 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .device = PCI_DEVICE_ID_ENE_CB712_SD, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | - SDHCI_QUIRK_BROKEN_DMA, + .driver_data = (kernel_ulong_t)&sdhci_ene_712, }, { @@ -69,8 +129,7 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .device = PCI_DEVICE_ID_ENE_CB712_SD_2, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | - SDHCI_QUIRK_BROKEN_DMA, + .driver_data = (kernel_ulong_t)&sdhci_ene_712, }, { @@ -78,9 +137,7 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .device = PCI_DEVICE_ID_ENE_CB714_SD, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | - SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS | - SDHCI_QUIRK_BROKEN_DMA, + .driver_data = (kernel_ulong_t)&sdhci_ene_714, }, { @@ -88,9 +145,7 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .device = PCI_DEVICE_ID_ENE_CB714_SD_2, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_SINGLE_POWER_WRITE | - SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS | - SDHCI_QUIRK_BROKEN_DMA, + .driver_data = (kernel_ulong_t)&sdhci_ene_714, }, { @@ -98,8 +153,7 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .device = PCI_DEVICE_ID_MARVELL_CAFE_SD, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER | - SDHCI_QUIRK_INCR_TIMEOUT_CONTROL, + .driver_data = (kernel_ulong_t)&sdhci_cafe, }, { @@ -107,9 +161,7 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .device = PCI_DEVICE_ID_JMICRON_JMB38X_SD, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, - .driver_data = SDHCI_QUIRK_32BIT_DMA_ADDR | - SDHCI_QUIRK_32BIT_DMA_SIZE | - SDHCI_QUIRK_RESET_AFTER_REQUEST, + .driver_data = (kernel_ulong_t)&sdhci_jmicron, }, { /* Generic SD host controller */ @@ -121,23 +173,6 @@ static const struct pci_device_id pci_ids[] __devinitdata = { MODULE_DEVICE_TABLE(pci, pci_ids); -struct sdhci_pci_chip; - -struct sdhci_pci_slot { - struct sdhci_pci_chip *chip; - struct sdhci_host *host; - - int pci_bar; -}; - -struct sdhci_pci_chip { - struct pci_dev *pdev; - unsigned int quirks; - - int num_slots; /* Slots on controller */ - struct sdhci_pci_slot *slots[MAX_SLOTS]; /* Pointers to host slots */ -}; - /*****************************************************************************\ * * * SDHCI core callbacks * @@ -389,11 +424,19 @@ static int __devinit sdhci_pci_probe(struct pci_dev *pdev, } chip->pdev = pdev; - chip->quirks = ent->driver_data; + chip->fixes = (const struct sdhci_pci_fixes*)ent->driver_data; + if (chip->fixes) + chip->quirks = chip->fixes->quirks; chip->num_slots = slots; pci_set_drvdata(pdev, chip); + if (chip->fixes && chip->fixes->probe) { + ret = chip->fixes->probe(chip); + if (ret) + goto free; + } + for (i = 0;i < slots;i++) { slot = sdhci_pci_probe_slot(pdev, chip, first_bar + i); if (IS_ERR(slot)) { -- cgit v1.1 From ee53ab5d73998e502801c024a08de2c39a92c52a Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sat, 5 Jul 2008 00:25:15 +0200 Subject: sdhci: make workaround for timeout bug more general Give the quirk for broken timeout handling a better chance of handling more controllers by simply classifying the system as broken and setting a fixed value. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci-pci.c | 2 +- drivers/mmc/host/sdhci.c | 50 ++++++++++++++++++++++++++------------------ drivers/mmc/host/sdhci.h | 4 ++-- 3 files changed, 33 insertions(+), 23 deletions(-) diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index 5094fe8..856bb2b 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -98,7 +98,7 @@ static const struct sdhci_pci_fixes sdhci_ene_714 = { static const struct sdhci_pci_fixes sdhci_cafe = { .quirks = SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER | - SDHCI_QUIRK_INCR_TIMEOUT_CONTROL, + SDHCI_QUIRK_BROKEN_TIMEOUT_VAL, }; static const struct sdhci_pci_fixes sdhci_jmicron = { diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 8ce01d4..95b081a 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -314,23 +314,19 @@ static void sdhci_transfer_pio(struct sdhci_host *host) DBG("PIO transfer complete.\n"); } -static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) +static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data) { u8 count; unsigned target_timeout, current_timeout; - WARN_ON(host->data); - - if (data == NULL) - return; - - /* Sanity checks */ - BUG_ON(data->blksz * data->blocks > 524288); - BUG_ON(data->blksz > host->mmc->max_blk_size); - BUG_ON(data->blocks > 65535); - - host->data = data; - host->data_early = 0; + /* + * If the host controller provides us with an incorrect timeout + * value, just skip the check and use 0xE. The hardware may take + * longer to time out, but that's much better than having a too-short + * timeout value. + */ + if ((host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)) + return 0xE; /* timeout in us */ target_timeout = data->timeout_ns / 1000 + @@ -355,19 +351,33 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) break; } - /* - * Compensate for an off-by-one error in the CaFe hardware; otherwise, - * a too-small count gives us interrupt timeouts. - */ - if ((host->quirks & SDHCI_QUIRK_INCR_TIMEOUT_CONTROL)) - count++; - if (count >= 0xF) { printk(KERN_WARNING "%s: Too large timeout requested!\n", mmc_hostname(host->mmc)); count = 0xE; } + return count; +} + +static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) +{ + u8 count; + + WARN_ON(host->data); + + if (data == NULL) + return; + + /* Sanity checks */ + BUG_ON(data->blksz * data->blocks > 524288); + BUG_ON(data->blksz > host->mmc->max_blk_size); + BUG_ON(data->blocks > 65535); + + host->data = data; + host->data_early = 0; + + count = sdhci_calc_timeout(host, data); writeb(count, host->ioaddr + SDHCI_TIMEOUT_CONTROL); if (host->flags & SDHCI_USE_DMA) diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 22fc258..7ce12f3 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -178,8 +178,8 @@ struct sdhci_host { #define SDHCI_QUIRK_RESET_AFTER_REQUEST (1<<8) /* Controller needs voltage and power writes to happen separately */ #define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<9) -/* Controller has an off-by-one issue with timeout value */ -#define SDHCI_QUIRK_INCR_TIMEOUT_CONTROL (1<<10) +/* Controller provides an incorrect timeout value for transfers */ +#define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL (1<<10) int irq; /* Device IRQ */ void __iomem * ioaddr; /* Mapped address */ -- cgit v1.1 From 45211e21598441a32e53cf5032b7faeac143df6d Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Mon, 24 Mar 2008 13:09:09 +0100 Subject: sdhci: toggle JMicron PMOS setting Some of the JMicron chips requires us to manually enable the power output stages of the chip. Add the necessary hooks and functions to manage this. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci-pci.c | 67 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 67 insertions(+) diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index 856bb2b..ef77ed1 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -44,6 +44,8 @@ struct sdhci_pci_fixes { unsigned int quirks; int (*probe)(struct sdhci_pci_chip*); + + int (*resume)(struct sdhci_pci_chip*); }; struct sdhci_pci_slot { @@ -101,10 +103,69 @@ static const struct sdhci_pci_fixes sdhci_cafe = { SDHCI_QUIRK_BROKEN_TIMEOUT_VAL, }; +static int jmicron_pmos(struct sdhci_pci_chip *chip, int on) +{ + u8 scratch; + int ret; + + ret = pci_read_config_byte(chip->pdev, 0xAE, &scratch); + if (ret) + return ret; + + /* + * Turn PMOS on [bit 0], set over current detection to 2.4 V + * [bit 1:2] and enable over current debouncing [bit 6]. + */ + if (on) + scratch |= 0x47; + else + scratch &= ~0x47; + + ret = pci_write_config_byte(chip->pdev, 0xAE, scratch); + if (ret) + return ret; + + return 0; +} + +static int jmicron_probe(struct sdhci_pci_chip *chip) +{ + int ret; + + /* + * JMicron chips need a bit of a nudge to enable the power + * output pins. + */ + ret = jmicron_pmos(chip, 1); + if (ret) { + dev_err(&chip->pdev->dev, "Failure enabling card power\n"); + return ret; + } + + return 0; +} + +static int jmicron_resume(struct sdhci_pci_chip *chip) +{ + int ret; + + ret = jmicron_pmos(chip, 1); + if (ret) { + dev_err(&chip->pdev->dev, "Failure enabling card power\n"); + return ret; + } + + return 0; +} + static const struct sdhci_pci_fixes sdhci_jmicron = { .quirks = SDHCI_QUIRK_32BIT_DMA_ADDR | SDHCI_QUIRK_32BIT_DMA_SIZE | SDHCI_QUIRK_RESET_AFTER_REQUEST, + + .probe = jmicron_probe, + + .resume = jmicron_resume, }; static const struct pci_device_id pci_ids[] __devinitdata = { @@ -264,6 +325,12 @@ static int sdhci_pci_resume (struct pci_dev *pdev) if (ret) return ret; + if (chip->fixes && chip->fixes->resume) { + ret = chip->fixes->resume(chip); + if (ret) + return ret; + } + for (i = 0;i < chip->num_slots;i++) { slot = chip->slots[i]; if (!slot) -- cgit v1.1 From 4489428ab5a49a6f443d9aa17f1d891417787d7b Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Fri, 4 Apr 2008 19:36:59 +0200 Subject: sdhci: support JMicron secondary interface JMicron chips sometimes have two interfaces to work around limitations in Microsoft's sdhci driver. This patch allows us to use either interface. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci-pci.c | 127 ++++++++++++++++++++++++++++++++++++++++++- include/linux/pci_ids.h | 1 + 2 files changed, 126 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index ef77ed1..5dcb495 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -39,12 +39,18 @@ #define MAX_SLOTS 8 struct sdhci_pci_chip; +struct sdhci_pci_slot; struct sdhci_pci_fixes { unsigned int quirks; int (*probe)(struct sdhci_pci_chip*); + int (*probe_slot)(struct sdhci_pci_slot*); + void (*remove_slot)(struct sdhci_pci_slot*); + + int (*suspend)(struct sdhci_pci_chip*, + pm_message_t); int (*resume)(struct sdhci_pci_chip*); }; @@ -133,6 +139,38 @@ static int jmicron_probe(struct sdhci_pci_chip *chip) int ret; /* + * JMicron chips can have two interfaces to the same hardware + * in order to work around limitations in Microsoft's driver. + * We need to make sure we only bind to one of them. + * + * This code assumes two things: + * + * 1. The PCI code adds subfunctions in order. + * + * 2. The MMC interface has a lower subfunction number + * than the SD interface. + */ + if (chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB38X_SD) { + struct pci_dev *sd_dev; + + sd_dev = NULL; + while ((sd_dev = pci_get_device(PCI_VENDOR_ID_JMICRON, + PCI_DEVICE_ID_JMICRON_JMB38X_MMC, sd_dev)) != NULL) { + if ((PCI_SLOT(chip->pdev->devfn) == + PCI_SLOT(sd_dev->devfn)) && + (chip->pdev->bus == sd_dev->bus)) + break; + } + + if (sd_dev) { + pci_dev_put(sd_dev); + dev_info(&chip->pdev->dev, "Refusing to bind to " + "secondary interface.\n"); + return -ENODEV; + } + } + + /* * JMicron chips need a bit of a nudge to enable the power * output pins. */ @@ -145,9 +183,58 @@ static int jmicron_probe(struct sdhci_pci_chip *chip) return 0; } +static void jmicron_enable_mmc(struct sdhci_host *host, int on) +{ + u8 scratch; + + scratch = readb(host->ioaddr + 0xC0); + + if (on) + scratch |= 0x01; + else + scratch &= ~0x01; + + writeb(scratch, host->ioaddr + 0xC0); +} + +static int jmicron_probe_slot(struct sdhci_pci_slot *slot) +{ + /* + * The secondary interface requires a bit set to get the + * interrupts. + */ + if (slot->chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB38X_MMC) + jmicron_enable_mmc(slot->host, 1); + + return 0; +} + +static void jmicron_remove_slot(struct sdhci_pci_slot *slot) +{ + if (slot->chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB38X_MMC) + jmicron_enable_mmc(slot->host, 0); +} + +static int jmicron_suspend(struct sdhci_pci_chip *chip, pm_message_t state) +{ + int i; + + if (chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB38X_MMC) { + for (i = 0;i < chip->num_slots;i++) + jmicron_enable_mmc(chip->slots[i]->host, 0); + } + + return 0; +} + static int jmicron_resume(struct sdhci_pci_chip *chip) { - int ret; + int ret, i; + + if (chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB38X_MMC) { + for (i = 0;i < chip->num_slots;i++) + jmicron_enable_mmc(chip->slots[i]->host, 1); + } ret = jmicron_pmos(chip, 1); if (ret) { @@ -165,6 +252,10 @@ static const struct sdhci_pci_fixes sdhci_jmicron = { .probe = jmicron_probe, + .probe_slot = jmicron_probe_slot, + .remove_slot = jmicron_remove_slot, + + .suspend = jmicron_suspend, .resume = jmicron_resume, }; @@ -225,6 +316,14 @@ static const struct pci_device_id pci_ids[] __devinitdata = { .driver_data = (kernel_ulong_t)&sdhci_jmicron, }, + { + .vendor = PCI_VENDOR_ID_JMICRON, + .device = PCI_DEVICE_ID_JMICRON_JMB38X_MMC, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .driver_data = (kernel_ulong_t)&sdhci_jmicron, + }, + { /* Generic SD host controller */ PCI_DEVICE_CLASS((PCI_CLASS_SYSTEM_SDHCI << 8), 0xFFFF00) }, @@ -301,6 +400,15 @@ static int sdhci_pci_suspend (struct pci_dev *pdev, pm_message_t state) } } + if (chip->fixes && chip->fixes->suspend) { + ret = chip->fixes->suspend(chip, state); + if (ret) { + for (i = chip->num_slots - 1;i >= 0;i--) + sdhci_resume_host(chip->slots[i]->host); + return ret; + } + } + pci_save_state(pdev); pci_enable_wake(pdev, pci_choose_state(pdev, state), 0); pci_disable_device(pdev); @@ -418,12 +526,22 @@ static struct sdhci_pci_slot * __devinit sdhci_pci_probe_slot( goto release; } + if (chip->fixes && chip->fixes->probe_slot) { + ret = chip->fixes->probe_slot(slot); + if (ret) + goto unmap; + } + ret = sdhci_add_host(host); if (ret) - goto unmap; + goto remove; return slot; +remove: + if (chip->fixes && chip->fixes->remove_slot) + chip->fixes->remove_slot(slot); + unmap: iounmap(host->ioaddr); @@ -437,7 +555,12 @@ release: static void sdhci_pci_remove_slot(struct sdhci_pci_slot *slot) { sdhci_remove_host(slot->host); + + if (slot->chip->fixes && slot->chip->fixes->remove_slot) + slot->chip->fixes->remove_slot(slot); + pci_release_region(slot->chip->pdev, slot->pci_bar); + sdhci_free_host(slot->host); } diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index 6595382..3015347 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -2188,6 +2188,7 @@ #define PCI_DEVICE_ID_JMICRON_JMB366 0x2366 #define PCI_DEVICE_ID_JMICRON_JMB368 0x2368 #define PCI_DEVICE_ID_JMICRON_JMB38X_SD 0x2381 +#define PCI_DEVICE_ID_JMICRON_JMB38X_MMC 0x2382 #define PCI_DEVICE_ID_JMICRON_JMB38X_MS 0x2383 #define PCI_VENDOR_ID_KORENIX 0x1982 -- cgit v1.1 From 1e72859e3ae16346d4007024b20d2d4ef387dcc3 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Wed, 16 Apr 2008 19:13:13 +0200 Subject: sdhci: handle hot-remove Gracefully handle when the device is suddenly removed. Do a test read and avoid any further access if that read returns -1. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci-pci.c | 21 ++++++++++++++----- drivers/mmc/host/sdhci.c | 48 ++++++++++++++++++++++++++++++++++++-------- drivers/mmc/host/sdhci.h | 3 ++- 3 files changed, 58 insertions(+), 14 deletions(-) diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index 5dcb495..8554466 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -47,7 +47,7 @@ struct sdhci_pci_fixes { int (*probe)(struct sdhci_pci_chip*); int (*probe_slot)(struct sdhci_pci_slot*); - void (*remove_slot)(struct sdhci_pci_slot*); + void (*remove_slot)(struct sdhci_pci_slot*, int); int (*suspend)(struct sdhci_pci_chip*, pm_message_t); @@ -209,8 +209,11 @@ static int jmicron_probe_slot(struct sdhci_pci_slot *slot) return 0; } -static void jmicron_remove_slot(struct sdhci_pci_slot *slot) +static void jmicron_remove_slot(struct sdhci_pci_slot *slot, int dead) { + if (dead) + return; + if (slot->chip->pdev->device == PCI_DEVICE_ID_JMICRON_JMB38X_MMC) jmicron_enable_mmc(slot->host, 0); } @@ -540,7 +543,7 @@ static struct sdhci_pci_slot * __devinit sdhci_pci_probe_slot( remove: if (chip->fixes && chip->fixes->remove_slot) - chip->fixes->remove_slot(slot); + chip->fixes->remove_slot(slot, 0); unmap: iounmap(host->ioaddr); @@ -554,10 +557,18 @@ release: static void sdhci_pci_remove_slot(struct sdhci_pci_slot *slot) { - sdhci_remove_host(slot->host); + int dead; + u32 scratch; + + dead = 0; + scratch = readl(slot->host->ioaddr + SDHCI_INT_STATUS); + if (scratch == (u32)-1) + dead = 1; + + sdhci_remove_host(slot->host, dead); if (slot->chip->fixes && slot->chip->fixes->remove_slot) - slot->chip->fixes->remove_slot(slot); + slot->chip->fixes->remove_slot(slot, dead); pci_release_region(slot->chip->pdev, slot->pci_bar); diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 95b081a..0ab582e 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -712,7 +712,8 @@ static void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq) host->mrq = mrq; - if (!(readl(host->ioaddr + SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT)) { + if (!(readl(host->ioaddr + SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT) + || (host->flags & SDHCI_DEVICE_DEAD)) { host->mrq->cmd->error = -ENOMEDIUM; tasklet_schedule(&host->finish_tasklet); } else @@ -732,6 +733,9 @@ static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) spin_lock_irqsave(&host->lock, flags); + if (host->flags & SDHCI_DEVICE_DEAD) + goto out; + /* * Reset the chip on each power off. * Should clear out any weird states. @@ -770,6 +774,7 @@ static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) if(host->quirks & SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS) sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA); +out: mmiowb(); spin_unlock_irqrestore(&host->lock, flags); } @@ -784,7 +789,10 @@ static int sdhci_get_ro(struct mmc_host *mmc) spin_lock_irqsave(&host->lock, flags); - present = readl(host->ioaddr + SDHCI_PRESENT_STATE); + if (host->flags & SDHCI_DEVICE_DEAD) + present = 0; + else + present = readl(host->ioaddr + SDHCI_PRESENT_STATE); spin_unlock_irqrestore(&host->lock, flags); @@ -801,6 +809,9 @@ static void sdhci_enable_sdio_irq(struct mmc_host *mmc, int enable) spin_lock_irqsave(&host->lock, flags); + if (host->flags & SDHCI_DEVICE_DEAD) + goto out; + ier = readl(host->ioaddr + SDHCI_INT_ENABLE); ier &= ~SDHCI_INT_CARD_INT; @@ -810,6 +821,7 @@ static void sdhci_enable_sdio_irq(struct mmc_host *mmc, int enable) writel(ier, host->ioaddr + SDHCI_INT_ENABLE); writel(ier, host->ioaddr + SDHCI_SIGNAL_ENABLE); +out: mmiowb(); spin_unlock_irqrestore(&host->lock, flags); @@ -875,10 +887,11 @@ static void sdhci_tasklet_finish(unsigned long param) * The controller needs a reset of internal state machines * upon error conditions. */ - if (mrq->cmd->error || - (mrq->data && (mrq->data->error || - (mrq->data->stop && mrq->data->stop->error))) || - (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST)) { + if (!(host->flags & SDHCI_DEVICE_DEAD) && + (mrq->cmd->error || + (mrq->data && (mrq->data->error || + (mrq->data->stop && mrq->data->stop->error))) || + (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST))) { /* Some controllers need this kick or reset won't work here */ if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET) { @@ -1378,15 +1391,34 @@ untasklet: EXPORT_SYMBOL_GPL(sdhci_add_host); -void sdhci_remove_host(struct sdhci_host *host) +void sdhci_remove_host(struct sdhci_host *host, int dead) { + unsigned long flags; + + if (dead) { + spin_lock_irqsave(&host->lock, flags); + + host->flags |= SDHCI_DEVICE_DEAD; + + if (host->mrq) { + printk(KERN_ERR "%s: Controller removed during " + " transfer!\n", mmc_hostname(host->mmc)); + + host->mrq->cmd->error = -ENOMEDIUM; + tasklet_schedule(&host->finish_tasklet); + } + + spin_unlock_irqrestore(&host->lock, flags); + } + mmc_remove_host(host->mmc); #ifdef CONFIG_LEDS_CLASS led_classdev_unregister(&host->led); #endif - sdhci_reset(host, SDHCI_RESET_ALL); + if (!dead) + sdhci_reset(host, SDHCI_RESET_ALL); free_irq(host->irq, host); diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 7ce12f3..7c30251 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -198,6 +198,7 @@ struct sdhci_host { int flags; /* Host attributes */ #define SDHCI_USE_DMA (1<<0) /* Host is DMA capable */ #define SDHCI_REQ_USE_DMA (1<<1) /* Use DMA for this req. */ +#define SDHCI_DEVICE_DEAD (1<<2) /* Device unresponsive */ unsigned int max_clk; /* Max possible freq (MHz) */ unsigned int timeout_clk; /* Timeout freq (KHz) */ @@ -239,7 +240,7 @@ static inline void *sdhci_priv(struct sdhci_host *host) } extern int sdhci_add_host(struct sdhci_host *host); -extern void sdhci_remove_host(struct sdhci_host *host); +extern void sdhci_remove_host(struct sdhci_host *host, int dead); #ifdef CONFIG_PM extern int sdhci_suspend_host(struct sdhci_host *host, pm_message_t state); -- cgit v1.1 From fd8c326cadd2f781d5c4d6bcee79bb17b3745bb0 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sat, 24 May 2008 22:36:31 +0200 Subject: mmc_test: add test case control Add the ability to run just a single test case by writing the test case number into the sysfs "test" file. Signed-off-by: Pierre Ossman --- drivers/mmc/card/mmc_test.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/card/mmc_test.c b/drivers/mmc/card/mmc_test.c index ffadee5..371d922 100644 --- a/drivers/mmc/card/mmc_test.c +++ b/drivers/mmc/card/mmc_test.c @@ -743,7 +743,7 @@ static const struct mmc_test_case mmc_test_cases[] = { static struct mutex mmc_test_lock; -static void mmc_test_run(struct mmc_test_card *test) +static void mmc_test_run(struct mmc_test_card *test, int testcase) { int i, ret; @@ -753,6 +753,9 @@ static void mmc_test_run(struct mmc_test_card *test) mmc_claim_host(test->card->host); for (i = 0;i < ARRAY_SIZE(mmc_test_cases);i++) { + if (testcase && ((i + 1) != testcase)) + continue; + printk(KERN_INFO "%s: Test case %d. %s...\n", mmc_hostname(test->card->host), i + 1, mmc_test_cases[i].name); @@ -824,9 +827,12 @@ static ssize_t mmc_test_store(struct device *dev, { struct mmc_card *card; struct mmc_test_card *test; + int testcase; card = container_of(dev, struct mmc_card, dev); + testcase = simple_strtol(buf, NULL, 10); + test = kzalloc(sizeof(struct mmc_test_card), GFP_KERNEL); if (!test) return -ENOMEM; @@ -836,7 +842,7 @@ static ssize_t mmc_test_store(struct device *dev, test->buffer = kzalloc(BUFFER_SIZE, GFP_KERNEL); if (test->buffer) { mutex_lock(&mmc_test_lock); - mmc_test_run(test); + mmc_test_run(test, testcase); mutex_unlock(&mmc_test_lock); } -- cgit v1.1 From 309d9736a903527d8bc41787b07573a054439bf6 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Wed, 28 May 2008 09:54:50 +0200 Subject: sdhci-pci: unaligned data with ricoh controllers The Ricoh controllers cannot handle unaligned data blocks. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci-pci.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index 8554466..c0fbf48 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -91,6 +91,7 @@ static int ricoh_probe(struct sdhci_pci_chip *chip) static const struct sdhci_pci_fixes sdhci_ricoh = { .probe = ricoh_probe, + .quirks = SDHCI_QUIRK_32BIT_DMA_ADDR, }; static const struct sdhci_pci_fixes sdhci_ene_712 = { -- cgit v1.1 From 150a55683b6b0ccb66aae75a10a3a514340c7c03 Mon Sep 17 00:00:00 2001 From: Adrian Bunk Date: Tue, 20 May 2008 00:57:27 +0300 Subject: include/linux/mmc/mmc.h: remove CVS tags This patch removes a CVS tag that wasn't updated for a long time. Signed-off-by: Adrian Bunk Signed-off-by: Pierre Ossman --- include/linux/mmc/mmc.h | 1 - 1 file changed, 1 deletion(-) diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h index 4236fbf..14b81f3 100644 --- a/include/linux/mmc/mmc.h +++ b/include/linux/mmc/mmc.h @@ -16,7 +16,6 @@ * Based strongly on code by: * * Author: Yong-iL Joh - * Date : $Date: 2002/06/18 12:37:30 $ * * Author: Andrew Christian * 15 May 2002 -- cgit v1.1 From 28f52482b41edc88cdf575aa6ed414c6e116ce10 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Tue, 17 Jun 2008 18:17:15 +0400 Subject: mmc: add support for card-detection polling Some hosts (and boards that use mmc_spi) do not use interrupts on the CD line, so they can't trigger mmc_detect_change. We want to poll the card and see if there was a change. 1 second poll interval seems resonable. This patch also implements .get_cd() host operation, that could be used by the hosts that are able to report card-detect status without need to talk MMC. Signed-off-by: Anton Vorontsov Signed-off-by: Pierre Ossman --- drivers/mmc/core/core.c | 12 +++++++++--- include/linux/mmc/host.h | 11 +++++++++++ 2 files changed, 20 insertions(+), 3 deletions(-) diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index 01ced4c..ede5d1e 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -638,6 +638,9 @@ void mmc_rescan(struct work_struct *work) */ mmc_bus_put(host); + if (host->ops->get_cd && host->ops->get_cd(host) == 0) + goto out; + mmc_claim_host(host); mmc_power_up(host); @@ -652,7 +655,7 @@ void mmc_rescan(struct work_struct *work) if (!err) { if (mmc_attach_sdio(host, ocr)) mmc_power_off(host); - return; + goto out; } /* @@ -662,7 +665,7 @@ void mmc_rescan(struct work_struct *work) if (!err) { if (mmc_attach_sd(host, ocr)) mmc_power_off(host); - return; + goto out; } /* @@ -672,7 +675,7 @@ void mmc_rescan(struct work_struct *work) if (!err) { if (mmc_attach_mmc(host, ocr)) mmc_power_off(host); - return; + goto out; } mmc_release_host(host); @@ -683,6 +686,9 @@ void mmc_rescan(struct work_struct *work) mmc_bus_put(host); } +out: + if (host->caps & MMC_CAP_NEEDS_POLL) + mmc_schedule_delayed_work(&host->detect, HZ); } void mmc_start_host(struct mmc_host *host) diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index 7ab962f..6188e19 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -51,8 +51,18 @@ struct mmc_ios { struct mmc_host_ops { void (*request)(struct mmc_host *host, struct mmc_request *req); + /* + * Avoid calling these three functions too often or in a "fast path", + * since underlaying controller might implement them in an expensive + * and/or slow way. + * + * Also note that these functions might sleep, so don't call them + * in the atomic contexts! + */ void (*set_ios)(struct mmc_host *host, struct mmc_ios *ios); int (*get_ro)(struct mmc_host *host); + int (*get_cd)(struct mmc_host *host); + void (*enable_sdio_irq)(struct mmc_host *host, int enable); }; @@ -94,6 +104,7 @@ struct mmc_host { #define MMC_CAP_SD_HIGHSPEED (1 << 3) /* Can do SD high-speed timing */ #define MMC_CAP_SDIO_IRQ (1 << 4) /* Can signal pending SDIO IRQs */ #define MMC_CAP_SPI (1 << 5) /* Talks only SPI protocols */ +#define MMC_CAP_NEEDS_POLL (1 << 6) /* Needs polling for card-detection */ /* host specific block data */ unsigned int max_seg_size; /* see blk_queue_max_segment_size */ -- cgit v1.1 From 619ef4b42128709de4d89d209b2c874f560deecd Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Tue, 17 Jun 2008 18:17:21 +0400 Subject: mmc_spi: add support for card-detection polling This patch adds new platform data variable "caps", so platforms could pass theirs capabilities into MMC core (for example, platforms without interrupt on the CD line will most probably want to pass MMC_CAP_NEEDS_POLL). New platform get_cd() callback provided to optimize polling. Signed-off-by: Anton Vorontsov Signed-off-by: Pierre Ossman --- drivers/mmc/host/mmc_spi.c | 19 +++++++++++++++++-- include/linux/spi/mmc_spi.h | 9 +++++++++ 2 files changed, 26 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c index 3550858..547eb85 100644 --- a/drivers/mmc/host/mmc_spi.c +++ b/drivers/mmc/host/mmc_spi.c @@ -1131,11 +1131,20 @@ static int mmc_spi_get_ro(struct mmc_host *mmc) return 0; } +static int mmc_spi_get_cd(struct mmc_host *mmc) +{ + struct mmc_spi_host *host = mmc_priv(mmc); + + if (host->pdata && host->pdata->get_cd) + return !!host->pdata->get_cd(mmc->parent); + return -ENOSYS; +} static const struct mmc_host_ops mmc_spi_ops = { .request = mmc_spi_request, .set_ios = mmc_spi_set_ios, .get_ro = mmc_spi_get_ro, + .get_cd = mmc_spi_get_cd, }; @@ -1319,17 +1328,23 @@ static int mmc_spi_probe(struct spi_device *spi) goto fail_glue_init; } + /* pass platform capabilities, if any */ + if (host->pdata) + mmc->caps |= host->pdata->caps; + status = mmc_add_host(mmc); if (status != 0) goto fail_add_host; - dev_info(&spi->dev, "SD/MMC host %s%s%s%s\n", + dev_info(&spi->dev, "SD/MMC host %s%s%s%s%s\n", mmc->class_dev.bus_id, host->dma_dev ? "" : ", no DMA", (host->pdata && host->pdata->get_ro) ? "" : ", no WP", (host->pdata && host->pdata->setpower) - ? "" : ", no poweroff"); + ? "" : ", no poweroff", + (mmc->caps & MMC_CAP_NEEDS_POLL) + ? ", cd polling" : ""); return 0; fail_add_host: diff --git a/include/linux/spi/mmc_spi.h b/include/linux/spi/mmc_spi.h index d5ca78b..a3626ae 100644 --- a/include/linux/spi/mmc_spi.h +++ b/include/linux/spi/mmc_spi.h @@ -23,6 +23,15 @@ struct mmc_spi_platform_data { /* sense switch on sd cards */ int (*get_ro)(struct device *); + /* + * If board does not use CD interrupts, driver can optimize polling + * using this function. + */ + int (*get_cd)(struct device *); + + /* Capabilities to pass into mmc core (e.g. MMC_CAP_NEEDS_POLL). */ + unsigned long caps; + /* how long to debounce card detect, in msecs */ u16 detect_delay; -- cgit v1.1 From 08f80bb5196517a0dfe50dc7c10f234c0ff2f0e8 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Tue, 17 Jun 2008 18:17:39 +0400 Subject: mmc: change .get_ro() callback semantics Now get_ro() callback must return 0/1 values for its logical states, and negative errno values in case of error. If particular host instance doesn't support RO/WP switch, it should return -ENOSYS. This patch changes some hosts in two ways: 1. Now functions should be smart to not return negative values in "RO asserted" case (particularly gpio_ calls could return negative values for the outermost GPIOs). Also, board code usually passes get_ro() callbacks that directly return gpioreg & bit result, so at91_mci, imxmmc, pxamci and mmc_spi's get_ro() handlers need take special care when returning platform's values to the mmc core. 2. In case of host instance didn't implement get_ro() callback, it should really return -ENOSYS and let the mmc core decide what to do about it (mmc core thinks the same way as the hosts, so it isn't functional change). Signed-off-by: Anton Vorontsov Signed-off-by: Pierre Ossman --- drivers/mmc/core/sd.c | 4 ++-- drivers/mmc/host/at91_mci.c | 18 +++++++----------- drivers/mmc/host/imxmmc.c | 9 ++++++--- drivers/mmc/host/mmc_spi.c | 9 ++++++--- drivers/mmc/host/pxamci.c | 9 ++++++--- drivers/mmc/host/wbsd.c | 2 +- include/linux/mmc/host.h | 12 ++++++++++++ 7 files changed, 40 insertions(+), 23 deletions(-) diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index 7ef3b15..b122eb9 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -494,13 +494,13 @@ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr, * Check if read-only switch is active. */ if (!oldcard) { - if (!host->ops->get_ro) { + if (!host->ops->get_ro || host->ops->get_ro(host) < 0) { printk(KERN_WARNING "%s: host does not " "support reading read-only " "switch. assuming write-enable.\n", mmc_hostname(host)); } else { - if (host->ops->get_ro(host)) + if (host->ops->get_ro(host) > 0) mmc_card_set_readonly(card); } } diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index 8979ad3..b9d4ed6 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -793,19 +793,15 @@ static irqreturn_t at91_mmc_det_irq(int irq, void *_host) static int at91_mci_get_ro(struct mmc_host *mmc) { - int read_only = 0; struct at91mci_host *host = mmc_priv(mmc); - if (host->board->wp_pin) { - read_only = gpio_get_value(host->board->wp_pin); - printk(KERN_WARNING "%s: card is %s\n", mmc_hostname(mmc), - (read_only ? "read-only" : "read-write") ); - } - else { - printk(KERN_WARNING "%s: host does not support reading read-only " - "switch. Assuming write-enable.\n", mmc_hostname(mmc)); - } - return read_only; + if (host->board->wp_pin) + return !!gpio_get_value(host->board->wp_pin); + /* + * Board doesn't support read only detection; let the mmc core + * decide what to do. + */ + return -ENOSYS; } static const struct mmc_host_ops at91_mci_ops = { diff --git a/drivers/mmc/host/imxmmc.c b/drivers/mmc/host/imxmmc.c index eed211b..5e880c0 100644 --- a/drivers/mmc/host/imxmmc.c +++ b/drivers/mmc/host/imxmmc.c @@ -892,9 +892,12 @@ static int imxmci_get_ro(struct mmc_host *mmc) struct imxmci_host *host = mmc_priv(mmc); if (host->pdata && host->pdata->get_ro) - return host->pdata->get_ro(mmc_dev(mmc)); - /* Host doesn't support read only detection so assume writeable */ - return 0; + return !!host->pdata->get_ro(mmc_dev(mmc)); + /* + * Board doesn't support read only detection; let the mmc core + * decide what to do. + */ + return -ENOSYS; } diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c index 547eb85..4e82f64 100644 --- a/drivers/mmc/host/mmc_spi.c +++ b/drivers/mmc/host/mmc_spi.c @@ -1126,9 +1126,12 @@ static int mmc_spi_get_ro(struct mmc_host *mmc) struct mmc_spi_host *host = mmc_priv(mmc); if (host->pdata && host->pdata->get_ro) - return host->pdata->get_ro(mmc->parent); - /* board doesn't support read only detection; assume writeable */ - return 0; + return !!host->pdata->get_ro(mmc->parent); + /* + * Board doesn't support read only detection; let the mmc core + * decide what to do. + */ + return -ENOSYS; } static int mmc_spi_get_cd(struct mmc_host *mmc) diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c index d89475d..d39f597 100644 --- a/drivers/mmc/host/pxamci.c +++ b/drivers/mmc/host/pxamci.c @@ -374,9 +374,12 @@ static int pxamci_get_ro(struct mmc_host *mmc) struct pxamci_host *host = mmc_priv(mmc); if (host->pdata && host->pdata->get_ro) - return host->pdata->get_ro(mmc_dev(mmc)); - /* Host doesn't support read only detection so assume writeable */ - return 0; + return !!host->pdata->get_ro(mmc_dev(mmc)); + /* + * Board doesn't support read only detection; let the mmc core + * decide what to do. + */ + return -ENOSYS; } static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) diff --git a/drivers/mmc/host/wbsd.c b/drivers/mmc/host/wbsd.c index c303e7f..67e5a9b 100644 --- a/drivers/mmc/host/wbsd.c +++ b/drivers/mmc/host/wbsd.c @@ -939,7 +939,7 @@ static int wbsd_get_ro(struct mmc_host *mmc) spin_unlock_bh(&host->lock); - return csr & WBSD_WRPT; + return !!(csr & WBSD_WRPT); } static const struct mmc_host_ops wbsd_ops = { diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index 6188e19..753b723 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -58,6 +58,18 @@ struct mmc_host_ops { * * Also note that these functions might sleep, so don't call them * in the atomic contexts! + * + * Return values for the get_ro callback should be: + * 0 for a read/write card + * 1 for a read-only card + * -ENOSYS when not supported (equal to NULL callback) + * or a negative errno value when something bad happened + * + * Return values for the get_ro callback should be: + * 0 for a absent card + * 1 for a present card + * -ENOSYS when not supported (equal to NULL callback) + * or a negative errno value when something bad happened */ void (*set_ios)(struct mmc_host *host, struct mmc_ios *ios); int (*get_ro)(struct mmc_host *host); -- cgit v1.1 From 8769392b1918ec70ab62eebc82e06c47c12f8304 Mon Sep 17 00:00:00 2001 From: Deepak Saxena Date: Mon, 16 Jun 2008 19:20:57 -0700 Subject: MMC: Trivial comment cleanup Make the variable name in the comments match the actual name of the variable. Signed-off-by: Deepak Saxena Signed-off-by: Pierre Ossman --- drivers/mmc/core/mmc.c | 2 +- drivers/mmc/core/sd.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c index 3da29ee..fdd7c76 100644 --- a/drivers/mmc/core/mmc.c +++ b/drivers/mmc/core/mmc.c @@ -288,7 +288,7 @@ static struct device_type mmc_type = { /* * Handle the detection and initialisation of a card. * - * In the case of a resume, "curcard" will contain the card + * In the case of a resume, "oldcard" will contain the card * we're trying to reinitialise. */ static int mmc_init_card(struct mmc_host *host, u32 ocr, diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index b122eb9..26fc098 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -326,7 +326,7 @@ static struct device_type sd_type = { /* * Handle the detection and initialisation of a card. * - * In the case of a resume, "curcard" will contain the card + * In the case of a resume, "oldcard" will contain the card * we're trying to reinitialise. */ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr, -- cgit v1.1 From 80f9254668c63ae73c1359d8de50ad94aa1aa94a Mon Sep 17 00:00:00 2001 From: Marc Pignat Date: Fri, 30 May 2008 14:05:24 +0200 Subject: mmc: at91_mci: support for block size not modulo 4 Implement transfer with size not modulo 4 for at91sam9*. Please note that the at91rm9200 simply can't handle this. Signed-off-by: Marc Pignat Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 15 ++++++++++----- 1 file changed, 10 insertions(+), 5 deletions(-) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index b9d4ed6..e40340f 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -233,11 +233,11 @@ static void at91_mci_pre_dma_read(struct at91mci_host *host) if (i == 0) { at91_mci_write(host, ATMEL_PDC_RPR, sg->dma_address); - at91_mci_write(host, ATMEL_PDC_RCR, sg->length / 4); + at91_mci_write(host, ATMEL_PDC_RCR, (data->blksz & 0x3) ? sg->length : sg->length / 4); } else { at91_mci_write(host, ATMEL_PDC_RNPR, sg->dma_address); - at91_mci_write(host, ATMEL_PDC_RNCR, sg->length / 4); + at91_mci_write(host, ATMEL_PDC_RNCR, (data->blksz & 0x3) ? sg->length : sg->length / 4); } } @@ -430,7 +430,7 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command if (data) { - if ( data->blksz & 0x3 ) { + if ( cpu_is_at91rm9200() && (data->blksz & 0x3) ) { pr_debug("Unsupported block size\n"); cmd->error = -EINVAL; mmc_request_done(host->mmc, host->request); @@ -482,7 +482,10 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command } else { /* zero block length and PDC mode */ mr = at91_mci_read(host, AT91_MCI_MR) & 0x7fff; - at91_mci_write(host, AT91_MCI_MR, mr | (block_length << 16) | AT91_MCI_PDCMODE); + mr |= (data->blksz & 0x3) ? AT91_MCI_PDCFBYTE : 0; + mr |= (block_length << 16); + mr |= AT91_MCI_PDCMODE; + at91_mci_write(host, AT91_MCI_MR, mr); /* * Disable the PDC controller @@ -517,7 +520,9 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command pr_debug("Transmitting %d bytes\n", host->total_length); at91_mci_write(host, ATMEL_PDC_TPR, host->physical_address); - at91_mci_write(host, ATMEL_PDC_TCR, host->total_length / 4); + at91_mci_write(host, ATMEL_PDC_TCR, (data->blksz & 0x3) ? + host->total_length : host->total_length / 4); + ier = AT91_MCI_CMDRDY; } } -- cgit v1.1 From e181dce8acab4f7d7c4772d2a8281510d503ab21 Mon Sep 17 00:00:00 2001 From: Marc Pignat Date: Fri, 30 May 2008 14:06:32 +0200 Subject: mmc: at91_mci: show timeouts Detect command timeout (or mci controller hangs). Signed-off-by: Marc Pignat Signed-off-by: Hans J Koch Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 35 +++++++++++++++++++++++++++++++++-- 1 file changed, 33 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index e40340f..fce171c 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -125,8 +125,33 @@ struct at91mci_host /* Latest in the scatterlist that has been enabled for transfer */ int transfer_index; + + /* Timer for timeouts */ + struct timer_list timer; }; +static void at91_timeout_timer(unsigned long data) +{ + struct at91mci_host *host; + + host = (struct at91mci_host *)data; + + if (host->request) { + dev_err(host->mmc->parent, "Timeout waiting end of packet\n"); + + if (host->cmd && host->cmd->data) { + host->cmd->data->error = -ETIMEDOUT; + } else { + if (host->cmd) + host->cmd->error = -ETIMEDOUT; + else + host->request->cmd->error = -ETIMEDOUT; + } + + mmc_request_done(host->mmc, host->request); + } +} + /* * Copy from sg to a dma block - used for transfers */ @@ -557,9 +582,10 @@ static void at91_mci_process_next(struct at91mci_host *host) else if ((!(host->flags & FL_SENT_STOP)) && host->request->stop) { host->flags |= FL_SENT_STOP; at91_mci_send_command(host, host->request->stop); - } - else + } else { + del_timer(&host->timer); mmc_request_done(host->mmc, host->request); + } } /* @@ -618,6 +644,8 @@ static void at91_mci_request(struct mmc_host *mmc, struct mmc_request *mrq) host->request = mrq; host->flags = 0; + mod_timer(&host->timer, jiffies + HZ); + at91_mci_process_next(host); } @@ -936,6 +964,8 @@ static int __init at91_mci_probe(struct platform_device *pdev) mmc_add_host(mmc); + setup_timer(&host->timer, at91_timeout_timer, (unsigned long)host); + /* * monitor card insertion/removal if we can */ @@ -996,6 +1026,7 @@ static int __exit at91_mci_remove(struct platform_device *pdev) } at91_mci_disable(host); + del_timer_sync(&host->timer); mmc_remove_host(mmc); free_irq(host->irq, host); -- cgit v1.1 From c5a89c6c0805959f813e8342d6f4040860f6d7db Mon Sep 17 00:00:00 2001 From: Marc Pignat Date: Fri, 30 May 2008 14:07:47 +0200 Subject: mmc: at91_mci: avoid timeouts The at91 mci controller internal state machine seems to often crash. This can be fixed by resetting the controller after each command for at91rm9200 and by setting the MCI_BLKR register on at91sam926*. Signed-off-by: Marc Pignat Signed-off-by: Hans J Koch Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 48 ++++++++++++++++++++++++++++++++++++ include/asm-arm/arch-at91/at91_mci.h | 4 +++ 2 files changed, 52 insertions(+) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index fce171c..e924211 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -130,6 +130,43 @@ struct at91mci_host struct timer_list timer; }; +/* + * Reset the controller and restore most of the state + */ +static void at91_reset_host(struct at91mci_host *host) +{ + unsigned long flags; + u32 mr; + u32 sdcr; + u32 dtor; + u32 imr; + + local_irq_save(flags); + imr = at91_mci_read(host, AT91_MCI_IMR); + + at91_mci_write(host, AT91_MCI_IDR, 0xffffffff); + + /* save current state */ + mr = at91_mci_read(host, AT91_MCI_MR) & 0x7fff; + sdcr = at91_mci_read(host, AT91_MCI_SDCR); + dtor = at91_mci_read(host, AT91_MCI_DTOR); + + /* reset the controller */ + at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIDIS | AT91_MCI_SWRST); + + /* restore state */ + at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIEN); + at91_mci_write(host, AT91_MCI_MR, mr); + at91_mci_write(host, AT91_MCI_SDCR, sdcr); + at91_mci_write(host, AT91_MCI_DTOR, dtor); + at91_mci_write(host, AT91_MCI_IER, imr); + + /* make sure sdio interrupts will fire */ + at91_mci_read(host, AT91_MCI_SR); + + local_irq_restore(flags); +} + static void at91_timeout_timer(unsigned long data) { struct at91mci_host *host; @@ -148,6 +185,7 @@ static void at91_timeout_timer(unsigned long data) host->request->cmd->error = -ETIMEDOUT; } + at91_reset_host(host); mmc_request_done(host->mmc, host->request); } } @@ -512,6 +550,11 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command mr |= AT91_MCI_PDCMODE; at91_mci_write(host, AT91_MCI_MR, mr); + if (!cpu_is_at91rm9200()) + at91_mci_write(host, AT91_MCI_BLKR, + AT91_MCI_BLKR_BCNT(blocks) | + AT91_MCI_BLKR_BLKLEN(block_length)); + /* * Disable the PDC controller */ @@ -584,6 +627,11 @@ static void at91_mci_process_next(struct at91mci_host *host) at91_mci_send_command(host, host->request->stop); } else { del_timer(&host->timer); + /* the at91rm9200 mci controller hangs after some transfers, + * and the workaround is to reset it after each transfer. + */ + if (cpu_is_at91rm9200()) + at91_reset_host(host); mmc_request_done(host->mmc, host->request); } } diff --git a/include/asm-arm/arch-at91/at91_mci.h b/include/asm-arm/arch-at91/at91_mci.h index 1551fc2..400ec10 100644 --- a/include/asm-arm/arch-at91/at91_mci.h +++ b/include/asm-arm/arch-at91/at91_mci.h @@ -75,6 +75,10 @@ #define AT91_MCI_TRTYP_MULTIPLE (1 << 19) #define AT91_MCI_TRTYP_STREAM (2 << 19) +#define AT91_MCI_BLKR 0x18 /* Block Register */ +#define AT91_MCI_BLKR_BCNT(n) ((0xffff & (n)) << 0) /* Block count */ +#define AT91_MCI_BLKR_BLKLEN(n) ((0xffff & (n)) << 16) /* Block lenght */ + #define AT91_MCI_RSPR(n) (0x20 + ((n) * 4)) /* Response Registers 0-3 */ #define AT91_MCR_RDR 0x30 /* Receive Data Register */ #define AT91_MCR_TDR 0x34 /* Transmit Data Register */ -- cgit v1.1 From 4ac24a8722b97d5b4cfc48a4fbd0b2489e358d4d Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 30 May 2008 14:18:57 +0200 Subject: mmc: at91_mci: update bytes_xfered value once xfer done Modify bytes_xfered value after a write. That will report, as accurately as possible, the amount of sectors that are effectively written. This update introduces the check of the busy signal given by the card. Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 40 ++++++++++++++++++++++++++++++++++------ 1 file changed, 34 insertions(+), 6 deletions(-) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index e924211..b5a6e25 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -340,8 +340,6 @@ static void at91_mci_post_dma_read(struct at91mci_host *host) dma_unmap_page(NULL, sg->dma_address, sg->length, DMA_FROM_DEVICE); - data->bytes_xfered += sg->length; - if (cpu_is_at91rm9200()) { /* AT91RM9200 errata */ unsigned int *buffer; int index; @@ -357,6 +355,8 @@ static void at91_mci_post_dma_read(struct at91mci_host *host) } flush_dcache_page(sg_page(sg)); + + data->bytes_xfered += sg->length; } /* Is there another transfer to trigger? */ @@ -397,10 +397,32 @@ static void at91_mci_handle_transmitted(struct at91mci_host *host) at91_mci_write(host, AT91_MCI_IER, AT91_MCI_BLKE); } else at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY); +} + +/* + * Update bytes tranfered count during a write operation + */ +static void at91_mci_update_bytes_xfered(struct at91mci_host *host) +{ + struct mmc_data *data; - data->bytes_xfered = host->total_length; + /* always deal with the effective request (and not the current cmd) */ + + if (host->request->cmd && host->request->cmd->error != 0) + return; + + if (host->request->data) { + data = host->request->data; + if (data->flags & MMC_DATA_WRITE) { + /* card is in IDLE mode now */ + pr_debug("-> bytes_xfered %d, total_length = %d\n", + data->bytes_xfered, host->total_length); + data->bytes_xfered = host->total_length; + } + } } + /*Handle after command sent ready*/ static int at91_mci_handle_cmdrdy(struct at91mci_host *host) { @@ -413,8 +435,7 @@ static int at91_mci_handle_cmdrdy(struct at91mci_host *host) } else return 1; } else if (host->cmd->data->flags & MMC_DATA_WRITE) { /*After sendding multi-block-write command, start DMA transfer*/ - at91_mci_write(host, AT91_MCI_IER, AT91_MCI_TXBUFE); - at91_mci_write(host, AT91_MCI_IER, AT91_MCI_BLKE); + at91_mci_write(host, AT91_MCI_IER, AT91_MCI_TXBUFE | AT91_MCI_BLKE); at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); } @@ -817,6 +838,7 @@ static irqreturn_t at91_mci_irq(int irq, void *devid) if (int_status & AT91_MCI_NOTBUSY) { pr_debug("Card is ready\n"); + at91_mci_update_bytes_xfered(host); completed = 1; } @@ -825,7 +847,13 @@ static irqreturn_t at91_mci_irq(int irq, void *devid) if (int_status & AT91_MCI_BLKE) { pr_debug("Block transfer has ended\n"); - completed = 1; + if (host->request->data && host->request->data->blocks > 1) { + /* multi block write : complete multi write + * command and send stop */ + completed = 1; + } else { + at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY); + } } if (int_status & AT91_MCI_TXRDY) -- cgit v1.1 From 3eb99a7bff3d7459a695f45124a6bbabf31cb4b5 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 30 May 2008 14:08:56 +0200 Subject: mmc: at91_mci: add multiwrite switch at91_mci is capable of multiwrite. Enable it before it disappears. Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index b5a6e25..b2bb79e 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -947,6 +947,7 @@ static int __init at91_mci_probe(struct platform_device *pdev) mmc->f_min = 375000; mmc->f_max = 25000000; mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; + mmc->caps = MMC_CAP_MULTIWRITE; mmc->max_blk_size = 4095; mmc->max_blk_count = mmc->max_req_size; -- cgit v1.1 From 7a6588ba20aed4505da912f9dd73616e9bd9ba67 Mon Sep 17 00:00:00 2001 From: Eric Benard Date: Fri, 30 May 2008 14:26:05 +0200 Subject: mmc: at91_mci: add sdio irq management Enable SDIO interrupt handling. Signed-off-by: Eric Benard Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 26 ++++++++++++++++++++++---- 1 file changed, 22 insertions(+), 4 deletions(-) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index b2bb79e..9b546a9 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -665,7 +665,7 @@ static void at91_mci_completed_command(struct at91mci_host *host) struct mmc_command *cmd = host->cmd; unsigned int status; - at91_mci_write(host, AT91_MCI_IDR, 0xffffffff); + at91_mci_write(host, AT91_MCI_IDR, 0xffffffff & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB)); cmd->resp[0] = at91_mci_read(host, AT91_MCI_RSPR(0)); cmd->resp[1] = at91_mci_read(host, AT91_MCI_RSPR(1)); @@ -856,6 +856,12 @@ static irqreturn_t at91_mci_irq(int irq, void *devid) } } + if (int_status & AT91_MCI_SDIOIRQA) + mmc_signal_sdio_irq(host->mmc); + + if (int_status & AT91_MCI_SDIOIRQB) + mmc_signal_sdio_irq(host->mmc); + if (int_status & AT91_MCI_TXRDY) pr_debug("Ready to transmit\n"); @@ -870,10 +876,10 @@ static irqreturn_t at91_mci_irq(int irq, void *devid) if (completed) { pr_debug("Completed command\n"); - at91_mci_write(host, AT91_MCI_IDR, 0xffffffff); + at91_mci_write(host, AT91_MCI_IDR, 0xffffffff & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB)); at91_mci_completed_command(host); } else - at91_mci_write(host, AT91_MCI_IDR, int_status); + at91_mci_write(host, AT91_MCI_IDR, int_status & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB)); return IRQ_HANDLED; } @@ -913,10 +919,22 @@ static int at91_mci_get_ro(struct mmc_host *mmc) return -ENOSYS; } +static void at91_mci_enable_sdio_irq(struct mmc_host *mmc, int enable) +{ + struct at91mci_host *host = mmc_priv(mmc); + + pr_debug("%s: sdio_irq %c : %s\n", mmc_hostname(host->mmc), + host->board->slot_b ? 'B':'A', enable ? "enable" : "disable"); + at91_mci_write(host, enable ? AT91_MCI_IER : AT91_MCI_IDR, + host->board->slot_b ? AT91_MCI_SDIOIRQB : AT91_MCI_SDIOIRQA); + +} + static const struct mmc_host_ops at91_mci_ops = { .request = at91_mci_request, .set_ios = at91_mci_set_ios, .get_ro = at91_mci_get_ro, + .enable_sdio_irq = at91_mci_enable_sdio_irq, }; /* @@ -947,7 +965,7 @@ static int __init at91_mci_probe(struct platform_device *pdev) mmc->f_min = 375000; mmc->f_max = 25000000; mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; - mmc->caps = MMC_CAP_MULTIWRITE; + mmc->caps = MMC_CAP_MULTIWRITE | MMC_CAP_SDIO_IRQ; mmc->max_blk_size = 4095; mmc->max_blk_count = mmc->max_req_size; -- cgit v1.1 From ba7deeed96ca1855c153ad81c45baf6efe1a3362 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 30 May 2008 14:28:45 +0200 Subject: mmc: at91_mci: do not read irq status twice as it will forget some errors Reading AT91_MCI_SR again at the end of transfer can corrupt the error reporting. Some fields in the SR register are read-and-clear. Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 12 +++++------- 1 file changed, 5 insertions(+), 7 deletions(-) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index 9b546a9..e1f91a4 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -660,10 +660,9 @@ static void at91_mci_process_next(struct at91mci_host *host) /* * Handle a command that has been completed */ -static void at91_mci_completed_command(struct at91mci_host *host) +static void at91_mci_completed_command(struct at91mci_host *host, unsigned int status) { struct mmc_command *cmd = host->cmd; - unsigned int status; at91_mci_write(host, AT91_MCI_IDR, 0xffffffff & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB)); @@ -677,10 +676,9 @@ static void at91_mci_completed_command(struct at91mci_host *host) host->buffer = NULL; } - status = at91_mci_read(host, AT91_MCI_SR); - - pr_debug("Status = %08X [%08X %08X %08X %08X]\n", - status, cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]); + pr_debug("Status = %08X/%08x [%08X %08X %08X %08X]\n", + status, at91_mci_read(host, AT91_MCI_SR), + cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]); if (status & AT91_MCI_ERRORS) { if ((status & AT91_MCI_RCRCE) && !(mmc_resp_type(cmd) & MMC_RSP_CRC)) { @@ -877,7 +875,7 @@ static irqreturn_t at91_mci_irq(int irq, void *devid) if (completed) { pr_debug("Completed command\n"); at91_mci_write(host, AT91_MCI_IDR, 0xffffffff & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB)); - at91_mci_completed_command(host); + at91_mci_completed_command(host, int_status); } else at91_mci_write(host, AT91_MCI_IDR, int_status & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB)); -- cgit v1.1 From fa1fe010c126ee69f2f75e3a4efc2f6252281ff8 Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Tue, 10 Jun 2008 11:27:29 +0200 Subject: at91_mci: manage cmd error and data error independently In at91_mci_completed_command() function, this patch distinguishes command error and data error. It reports it in the corresponding error field. Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 27 +++++++++++++++++++-------- 1 file changed, 19 insertions(+), 8 deletions(-) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index e1f91a4..e4d018b 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -663,6 +663,7 @@ static void at91_mci_process_next(struct at91mci_host *host) static void at91_mci_completed_command(struct at91mci_host *host, unsigned int status) { struct mmc_command *cmd = host->cmd; + struct mmc_data *data = cmd->data; at91_mci_write(host, AT91_MCI_IDR, 0xffffffff & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB)); @@ -685,15 +686,25 @@ static void at91_mci_completed_command(struct at91mci_host *host, unsigned int s cmd->error = 0; } else { - if (status & (AT91_MCI_RTOE | AT91_MCI_DTOE)) - cmd->error = -ETIMEDOUT; - else if (status & (AT91_MCI_RCRCE | AT91_MCI_DCRCE)) - cmd->error = -EILSEQ; - else - cmd->error = -EIO; + if (status & (AT91_MCI_DTOE | AT91_MCI_DCRCE)) { + if (data) { + if (status & AT91_MCI_DTOE) + data->error = -ETIMEDOUT; + else if (status & AT91_MCI_DCRCE) + data->error = -EILSEQ; + } + } else { + if (status & AT91_MCI_RTOE) + cmd->error = -ETIMEDOUT; + else if (status & AT91_MCI_RCRCE) + cmd->error = -EILSEQ; + else + cmd->error = -EIO; + } - pr_debug("Error detected and set to %d (cmd = %d, retries = %d)\n", - cmd->error, cmd->opcode, cmd->retries); + pr_debug("Error detected and set to %d/%d (cmd = %d, retries = %d)\n", + cmd->error, data ? data->error : 0, + cmd->opcode, cmd->retries); } } else -- cgit v1.1 From 5385edc50063a2175383ef5e90aa67fb6ab1beae Mon Sep 17 00:00:00 2001 From: Ville Syrjala Date: Sat, 14 Jun 2008 20:27:20 +0300 Subject: at91_mci: AT91SAM9260/9263 12 byte write erratum (v2) AT91SAM926[0/3] PDC must write at least 12 bytes. The code compiles and runs but the actual condition for this erratum did not trigger in my tests so it's unclear if it actually works as intended. Signed-off-by: Ville Syrjala Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 21 +++++++++++++++++---- 1 file changed, 17 insertions(+), 4 deletions(-) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index e4d018b..d3e96ff 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -198,9 +198,14 @@ static inline void at91_mci_sg_to_dma(struct at91mci_host *host, struct mmc_data unsigned int len, i, size; unsigned *dmabuf = host->buffer; - size = host->total_length; + size = data->blksz * data->blocks; len = data->sg_len; + /* AT91SAM926[0/3] Data Write Operation and number of bytes erratum */ + if (cpu_is_at91sam9260() || cpu_is_at91sam9263()) + if (host->total_length == 12) + memset(dmabuf, 0, 12); + /* * Just loop through all entries. Size might not * be the entire list though so make sure that @@ -222,9 +227,10 @@ static inline void at91_mci_sg_to_dma(struct at91mci_host *host, struct mmc_data for (index = 0; index < (amount / 4); index++) *dmabuf++ = swab32(sgbuffer[index]); - } - else + } else { memcpy(dmabuf, sgbuffer, amount); + dmabuf += amount; + } kunmap_atomic(sgbuffer, KM_BIO_SRC_IRQ); @@ -417,7 +423,7 @@ static void at91_mci_update_bytes_xfered(struct at91mci_host *host) /* card is in IDLE mode now */ pr_debug("-> bytes_xfered %d, total_length = %d\n", data->bytes_xfered, host->total_length); - data->bytes_xfered = host->total_length; + data->bytes_xfered = data->blksz * data->blocks; } } } @@ -600,6 +606,13 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command * Handle a write */ host->total_length = block_length * blocks; + /* + * AT91SAM926[0/3] Data Write Operation and + * number of bytes erratum + */ + if (cpu_is_at91sam9260 () || cpu_is_at91sam9263()) + if (host->total_length < 12) + host->total_length = 12; host->buffer = dma_alloc_coherent(NULL, host->total_length, &host->physical_address, GFP_KERNEL); -- cgit v1.1 From 9da3cbaf2881df97e502593c49c93f55eb696091 Mon Sep 17 00:00:00 2001 From: Ville Syrjala Date: Mon, 9 Jun 2008 22:06:44 +0300 Subject: at91_mci: Cover more AT91RM9200 and AT91SAM9261 errata. According to the documentation the AT91SAM9261 MCI shares the block size limitations of the AT91RM9200 MCI. Also the errata documentation for AT91RM9200 and AT91SAM9261 state that stream commands are not supported. This has not been tested on actual hardware. Signed-off-by: Ville Syrjala Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 20 ++++++++++++++------ 1 file changed, 14 insertions(+), 6 deletions(-) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index d3e96ff..f8c3f7c 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -520,11 +520,19 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command if (data) { - if ( cpu_is_at91rm9200() && (data->blksz & 0x3) ) { - pr_debug("Unsupported block size\n"); - cmd->error = -EINVAL; - mmc_request_done(host->mmc, host->request); - return; + if (cpu_is_at91rm9200() || cpu_is_at91sam9261()) { + if (data->blksz & 0x3) { + pr_debug("Unsupported block size\n"); + cmd->error = -EINVAL; + mmc_request_done(host->mmc, host->request); + return; + } + if (data->flags & MMC_DATA_STREAM) { + pr_debug("Stream commands not supported\n"); + cmd->error = -EINVAL; + mmc_request_done(host->mmc, host->request); + return; + } } block_length = data->blksz; @@ -577,7 +585,7 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command mr |= AT91_MCI_PDCMODE; at91_mci_write(host, AT91_MCI_MR, mr); - if (!cpu_is_at91rm9200()) + if (!(cpu_is_at91rm9200() || cpu_is_at91sam9261())) at91_mci_write(host, AT91_MCI_BLKR, AT91_MCI_BLKR_BCNT(blocks) | AT91_MCI_BLKR_BLKLEN(block_length)); -- cgit v1.1 From 12bd257532708a4d5be4b8548ff121a45ff88f5d Mon Sep 17 00:00:00 2001 From: Ville Syrjala Date: Mon, 9 Jun 2008 22:06:45 +0300 Subject: at91_mci: Fix byte mode transitions. The byte mode support fails to clear the byte mode bit in the command register, possibly leaving byte mode enabled with the counters programmed in non-byte mode. Signed-off-by: Ville Syrjala Signed-off-by: Nicolas Ferre Signed-off-by: Pierre Ossman --- drivers/mmc/host/at91_mci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index f8c3f7c..16df235 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -579,7 +579,7 @@ static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command ier = AT91_MCI_CMDRDY; } else { /* zero block length and PDC mode */ - mr = at91_mci_read(host, AT91_MCI_MR) & 0x7fff; + mr = at91_mci_read(host, AT91_MCI_MR) & 0x5fff; mr |= (data->blksz & 0x3) ? AT91_MCI_PDCFBYTE : 0; mr |= (block_length << 16); mr |= AT91_MCI_PDCMODE; -- cgit v1.1 From c4223c2c91fa9e5addd6eadd804e57a925ac5e5e Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Mon, 9 Jun 2008 08:36:13 +0200 Subject: au1xmmc: remove db1200 board code, rewrite probe. Remove the DB1200 board-specific functions (card present, read-only, activity LED methods) and instead add platform data which is passed to the driver. This also allows for platforms to implement other carddetect schemes (e.g. dedicated irq) without having to pollute the driver code. The poll timer (used for pb1200) is kept for compatibility. With the board-specific stuff gone, the driver's ->probe() code can be cleaned up considerably. Signed-off-by: Manuel Lauss Signed-off-by: Pierre Ossman --- drivers/mmc/host/au1xmmc.c | 573 ++++++++++++++++++------------ drivers/mmc/host/au1xmmc.h | 9 +- include/asm-mips/mach-au1x00/au1100_mmc.h | 18 +- 3 files changed, 354 insertions(+), 246 deletions(-) diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c index cc5f7bc..d8776d6 100644 --- a/drivers/mmc/host/au1xmmc.c +++ b/drivers/mmc/host/au1xmmc.c @@ -41,8 +41,9 @@ #include #include #include - +#include #include + #include #include #include @@ -54,6 +55,7 @@ #define DRIVER_NAME "au1xxx-mmc" /* Set this to enable special debugging macros */ +/* #define DEBUG */ #ifdef DEBUG #define DBG(fmt, idx, args...) printk("au1xx(%d): DEBUG: " fmt, idx, ##args) @@ -61,32 +63,6 @@ #define DBG(fmt, idx, args...) #endif -const struct { - u32 iobase; - u32 tx_devid, rx_devid; - u16 bcsrpwr; - u16 bcsrstatus; - u16 wpstatus; -} au1xmmc_card_table[] = { - { SD0_BASE, DSCR_CMD0_SDMS_TX0, DSCR_CMD0_SDMS_RX0, - BCSR_BOARD_SD0PWR, BCSR_INT_SD0INSERT, BCSR_STATUS_SD0WP }, -#ifndef CONFIG_MIPS_DB1200 - { SD1_BASE, DSCR_CMD0_SDMS_TX1, DSCR_CMD0_SDMS_RX1, - BCSR_BOARD_DS1PWR, BCSR_INT_SD1INSERT, BCSR_STATUS_SD1WP } -#endif -}; - -#define AU1XMMC_CONTROLLER_COUNT (ARRAY_SIZE(au1xmmc_card_table)) - -/* This array stores pointers for the hosts (used by the IRQ handler) */ -struct au1xmmc_host *au1xmmc_hosts[AU1XMMC_CONTROLLER_COUNT]; -static int dma = 1; - -#ifdef MODULE -module_param(dma, bool, 0); -MODULE_PARM_DESC(dma, "Use DMA engine for data transfers (0 = disabled)"); -#endif - static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask) { u32 val = au_readl(HOST_CONFIG(host)); @@ -135,26 +111,33 @@ static inline void SEND_STOP(struct au1xmmc_host *host) static void au1xmmc_set_power(struct au1xmmc_host *host, int state) { - - u32 val = au1xmmc_card_table[host->id].bcsrpwr; - - bcsr->board &= ~val; - if (state) bcsr->board |= val; - - au_sync_delay(1); + if (host->platdata && host->platdata->set_power) + host->platdata->set_power(host->mmc, state); } -static inline int au1xmmc_card_inserted(struct au1xmmc_host *host) +static int au1xmmc_card_inserted(struct au1xmmc_host *host) { - return (bcsr->sig_status & au1xmmc_card_table[host->id].bcsrstatus) - ? 1 : 0; + int ret; + + if (host->platdata && host->platdata->card_inserted) + ret = host->platdata->card_inserted(host->mmc); + else + ret = 1; /* assume there is a card */ + + return ret; } static int au1xmmc_card_readonly(struct mmc_host *mmc) { struct au1xmmc_host *host = mmc_priv(mmc); - return (bcsr->status & au1xmmc_card_table[host->id].wpstatus) - ? 1 : 0; + int ret; + + if (host->platdata && host->platdata->card_readonly) + ret = host->platdata->card_readonly(mmc); + else + ret = 0; /* assume card is read-write */ + + return ret; } static void au1xmmc_finish_request(struct au1xmmc_host *host) @@ -163,7 +146,7 @@ static void au1xmmc_finish_request(struct au1xmmc_host *host) struct mmc_request *mrq = host->mrq; host->mrq = NULL; - host->flags &= HOST_F_ACTIVE; + host->flags &= HOST_F_ACTIVE | HOST_F_DMA; host->dma.len = 0; host->dma.dir = 0; @@ -174,8 +157,6 @@ static void au1xmmc_finish_request(struct au1xmmc_host *host) host->status = HOST_S_IDLE; - bcsr->disk_leds |= (1 << 8); - mmc_request_done(host->mmc, mrq); } @@ -299,11 +280,13 @@ static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) if (!data->error) { if (host->flags & HOST_F_DMA) { +#ifdef CONFIG_SOC_AU1200 /* DBDMA */ u32 chan = DMA_CHANNEL(host); chan_tab_t *c = *((chan_tab_t **) chan); au1x_dma_chan_t *cp = c->chan_ptr; data->bytes_xfered = cp->ddma_bytecnt; +#endif } else data->bytes_xfered = @@ -420,18 +403,18 @@ static void au1xmmc_receive_pio(struct au1xmmc_host *host) break; if (status & SD_STATUS_RC) { - DBG("RX CRC Error [%d + %d].\n", host->id, + DBG("RX CRC Error [%d + %d].\n", host->pdev->id, host->pio.len, count); break; } if (status & SD_STATUS_RO) { - DBG("RX Overrun [%d + %d]\n", host->id, + DBG("RX Overrun [%d + %d]\n", host->pdev->id, host->pio.len, count); break; } else if (status & SD_STATUS_RU) { - DBG("RX Underrun [%d + %d]\n", host->id, + DBG("RX Underrun [%d + %d]\n", host->pdev->id, host->pio.len, count); break; } @@ -528,6 +511,7 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) host->status = HOST_S_DATA; if (host->flags & HOST_F_DMA) { +#ifdef CONFIG_SOC_AU1200 /* DBDMA */ u32 channel = DMA_CHANNEL(host); /* Start the DMA as soon as the buffer gets something in it */ @@ -540,6 +524,7 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) } au1xxx_dbdma_start(channel); +#endif } } @@ -571,12 +556,8 @@ static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate) static int au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) { - int datalen = data->blocks * data->blksz; - if (dma != 0) - host->flags |= HOST_F_DMA; - if (data->flags & MMC_DATA_READ) host->flags |= HOST_F_RECV; else @@ -596,6 +577,7 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) au_writel(data->blksz - 1, HOST_BLKSIZE(host)); if (host->flags & HOST_F_DMA) { +#ifdef CONFIG_SOC_AU1200 /* DBDMA */ int i; u32 channel = DMA_CHANNEL(host); @@ -621,11 +603,12 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) len, flags); } - if (!ret) + if (!ret) goto dataerr; datalen -= len; } +#endif } else { host->pio.index = 0; @@ -641,8 +624,9 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) return 0; - dataerr: - dma_unmap_sg(mmc_dev(host->mmc),data->sg,data->sg_len,host->dma.dir); +dataerr: + dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, + host->dma.dir); return -ETIMEDOUT; } @@ -663,8 +647,6 @@ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) host->mrq = mrq; host->status = HOST_S_CMD; - bcsr->disk_leds &= ~(1 << 8); - if (mrq->data) { FLUSH_FIFO(host); flags = mrq->data->flags; @@ -728,149 +710,145 @@ static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios) } } -static void au1xmmc_dma_callback(int irq, void *dev_id) -{ - struct au1xmmc_host *host = (struct au1xmmc_host *) dev_id; - - /* Avoid spurious interrupts */ - - if (!host->mrq) - return; - - if (host->flags & HOST_F_STOP) - SEND_STOP(host); - - tasklet_schedule(&host->data_task); -} - #define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT) #define STATUS_DATA_IN (SD_STATUS_NE) #define STATUS_DATA_OUT (SD_STATUS_TH) static irqreturn_t au1xmmc_irq(int irq, void *dev_id) { - + struct au1xmmc_host *host = dev_id; u32 status; - int i, ret = 0; - - disable_irq(AU1100_SD_IRQ); - for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) { - struct au1xmmc_host * host = au1xmmc_hosts[i]; - u32 handled = 1; - - status = au_readl(HOST_STATUS(host)); + status = au_readl(HOST_STATUS(host)); - if (host->mrq && (status & STATUS_TIMEOUT)) { - if (status & SD_STATUS_RAT) - host->mrq->cmd->error = -ETIMEDOUT; + if (!(status & SD_STATUS_I)) + return IRQ_NONE; /* not ours */ - else if (status & SD_STATUS_DT) - host->mrq->data->error = -ETIMEDOUT; + if (host->mrq && (status & STATUS_TIMEOUT)) { + if (status & SD_STATUS_RAT) + host->mrq->cmd->error = -ETIMEDOUT; + else if (status & SD_STATUS_DT) + host->mrq->data->error = -ETIMEDOUT; - /* In PIO mode, interrupts might still be enabled */ - IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH); + /* In PIO mode, interrupts might still be enabled */ + IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH); - //IRQ_OFF(host, SD_CONFIG_TH|SD_CONFIG_RA|SD_CONFIG_RF); - tasklet_schedule(&host->finish_task); - } + /* IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA | SD_CONFIG_RF); */ + tasklet_schedule(&host->finish_task); + } #if 0 - else if (status & SD_STATUS_DD) { - - /* Sometimes we get a DD before a NE in PIO mode */ - - if (!(host->flags & HOST_F_DMA) && - (status & SD_STATUS_NE)) - au1xmmc_receive_pio(host); - else { - au1xmmc_data_complete(host, status); - //tasklet_schedule(&host->data_task); - } - } -#endif - else if (status & (SD_STATUS_CR)) { - if (host->status == HOST_S_CMD) - au1xmmc_cmd_complete(host,status); - } - else if (!(host->flags & HOST_F_DMA)) { - if ((host->flags & HOST_F_XMIT) && - (status & STATUS_DATA_OUT)) - au1xmmc_send_pio(host); - else if ((host->flags & HOST_F_RECV) && - (status & STATUS_DATA_IN)) - au1xmmc_receive_pio(host); - } - else if (status & 0x203FBC70) { - DBG("Unhandled status %8.8x\n", host->id, status); - handled = 0; + else if (status & SD_STATUS_DD) { + /* Sometimes we get a DD before a NE in PIO mode */ + if (!(host->flags & HOST_F_DMA) && (status & SD_STATUS_NE)) + au1xmmc_receive_pio(host); + else { + au1xmmc_data_complete(host, status); + /* tasklet_schedule(&host->data_task); */ } - - au_writel(status, HOST_STATUS(host)); - au_sync(); - - ret |= handled; } - - enable_irq(AU1100_SD_IRQ); - return ret; -} - -static void au1xmmc_poll_event(unsigned long arg) -{ - struct au1xmmc_host *host = (struct au1xmmc_host *) arg; - - int card = au1xmmc_card_inserted(host); - int controller = (host->flags & HOST_F_ACTIVE) ? 1 : 0; - - if (card != controller) { - host->flags &= ~HOST_F_ACTIVE; - if (card) host->flags |= HOST_F_ACTIVE; - mmc_detect_change(host->mmc, 0); +#endif + else if (status & SD_STATUS_CR) { + if (host->status == HOST_S_CMD) + au1xmmc_cmd_complete(host, status); + + } else if (!(host->flags & HOST_F_DMA)) { + if ((host->flags & HOST_F_XMIT) && (status & STATUS_DATA_OUT)) + au1xmmc_send_pio(host); + else if ((host->flags & HOST_F_RECV) && (status & STATUS_DATA_IN)) + au1xmmc_receive_pio(host); + + } else if (status & 0x203F3C70) { + DBG("Unhandled status %8.8x\n", host->pdev->id, + status); } - if (host->mrq != NULL) { - u32 status = au_readl(HOST_STATUS(host)); - DBG("PENDING - %8.8x\n", host->id, status); - } + au_writel(status, HOST_STATUS(host)); + au_sync(); - mod_timer(&host->timer, jiffies + AU1XMMC_DETECT_TIMEOUT); + return IRQ_HANDLED; } -static dbdev_tab_t au1xmmc_mem_dbdev = -{ - DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 8, 0x00000000, 0, 0 +#ifdef CONFIG_SOC_AU1200 +/* 8bit memory DMA device */ +static dbdev_tab_t au1xmmc_mem_dbdev = { + .dev_id = DSCR_CMD0_ALWAYS, + .dev_flags = DEV_FLAGS_ANYUSE, + .dev_tsize = 0, + .dev_devwidth = 8, + .dev_physaddr = 0x00000000, + .dev_intlevel = 0, + .dev_intpolarity = 0, }; +static int memid; -static void au1xmmc_init_dma(struct au1xmmc_host *host) +static void au1xmmc_dbdma_callback(int irq, void *dev_id) { + struct au1xmmc_host *host = (struct au1xmmc_host *)dev_id; - u32 rxchan, txchan; + /* Avoid spurious interrupts */ + if (!host->mrq) + return; - int txid = au1xmmc_card_table[host->id].tx_devid; - int rxid = au1xmmc_card_table[host->id].rx_devid; + if (host->flags & HOST_F_STOP) + SEND_STOP(host); - /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride - of 8 bits. And since devices are shared, we need to create - our own to avoid freaking out other devices - */ + tasklet_schedule(&host->data_task); +} - int memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev); +static int au1xmmc_dbdma_init(struct au1xmmc_host *host) +{ + struct resource *res; + int txid, rxid; + + res = platform_get_resource(host->pdev, IORESOURCE_DMA, 0); + if (!res) + return -ENODEV; + txid = res->start; + + res = platform_get_resource(host->pdev, IORESOURCE_DMA, 1); + if (!res) + return -ENODEV; + rxid = res->start; + + if (!memid) + return -ENODEV; + + host->tx_chan = au1xxx_dbdma_chan_alloc(memid, txid, + au1xmmc_dbdma_callback, (void *)host); + if (!host->tx_chan) { + dev_err(&host->pdev->dev, "cannot allocate TX DMA\n"); + return -ENODEV; + } + + host->rx_chan = au1xxx_dbdma_chan_alloc(rxid, memid, + au1xmmc_dbdma_callback, (void *)host); + if (!host->rx_chan) { + dev_err(&host->pdev->dev, "cannot allocate RX DMA\n"); + au1xxx_dbdma_chan_free(host->tx_chan); + return -ENODEV; + } - txchan = au1xxx_dbdma_chan_alloc(memid, txid, - au1xmmc_dma_callback, (void *) host); + au1xxx_dbdma_set_devwidth(host->tx_chan, 8); + au1xxx_dbdma_set_devwidth(host->rx_chan, 8); - rxchan = au1xxx_dbdma_chan_alloc(rxid, memid, - au1xmmc_dma_callback, (void *) host); + au1xxx_dbdma_ring_alloc(host->tx_chan, AU1XMMC_DESCRIPTOR_COUNT); + au1xxx_dbdma_ring_alloc(host->rx_chan, AU1XMMC_DESCRIPTOR_COUNT); - au1xxx_dbdma_set_devwidth(txchan, 8); - au1xxx_dbdma_set_devwidth(rxchan, 8); + /* DBDMA is good to go */ + host->flags |= HOST_F_DMA; - au1xxx_dbdma_ring_alloc(txchan, AU1XMMC_DESCRIPTOR_COUNT); - au1xxx_dbdma_ring_alloc(rxchan, AU1XMMC_DESCRIPTOR_COUNT); + return 0; +} - host->tx_chan = txchan; - host->rx_chan = rxchan; +static void au1xmmc_dbdma_shutdown(struct au1xmmc_host *host) +{ + if (host->flags & HOST_F_DMA) { + host->flags &= ~HOST_F_DMA; + au1xxx_dbdma_chan_free(host->tx_chan); + au1xxx_dbdma_chan_free(host->rx_chan); + } } +#endif static const struct mmc_host_ops au1xmmc_ops = { .request = au1xmmc_request, @@ -878,116 +856,235 @@ static const struct mmc_host_ops au1xmmc_ops = { .get_ro = au1xmmc_card_readonly, }; -static int __devinit au1xmmc_probe(struct platform_device *pdev) +static void au1xmmc_poll_event(unsigned long arg) { + struct au1xmmc_host *host = (struct au1xmmc_host *)arg; + int card = au1xmmc_card_inserted(host); + int controller = (host->flags & HOST_F_ACTIVE) ? 1 : 0; + + if (card != controller) { + host->flags &= ~HOST_F_ACTIVE; + if (card) + host->flags |= HOST_F_ACTIVE; + mmc_detect_change(host->mmc, 0); + } - int i, ret = 0; +#ifdef DEBUG + if (host->mrq != NULL) { + u32 status = au_readl(HOST_STATUS(host)); + DBG("PENDING - %8.8x\n", host->pdev->id, status); + } +#endif + mod_timer(&host->timer, jiffies + AU1XMMC_DETECT_TIMEOUT); +} - /* THe interrupt is shared among all controllers */ - ret = request_irq(AU1100_SD_IRQ, au1xmmc_irq, IRQF_DISABLED, "MMC", 0); +static void au1xmmc_init_cd_poll_timer(struct au1xmmc_host *host) +{ + init_timer(&host->timer); + host->timer.function = au1xmmc_poll_event; + host->timer.data = (unsigned long)host; + host->timer.expires = jiffies + AU1XMMC_DETECT_TIMEOUT; +} - if (ret) { - printk(DRIVER_NAME "ERROR: Couldn't get int %d: %d\n", - AU1100_SD_IRQ, ret); - return -ENXIO; +static int __devinit au1xmmc_probe(struct platform_device *pdev) +{ + struct mmc_host *mmc; + struct au1xmmc_host *host; + struct resource *r; + int ret; + + mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev); + if (!mmc) { + dev_err(&pdev->dev, "no memory for mmc_host\n"); + ret = -ENOMEM; + goto out0; } - disable_irq(AU1100_SD_IRQ); + host = mmc_priv(mmc); + host->mmc = mmc; + host->platdata = pdev->dev.platform_data; + host->pdev = pdev; - for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) { - struct mmc_host *mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev); - struct au1xmmc_host *host = 0; + ret = -ENODEV; + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!r) { + dev_err(&pdev->dev, "no mmio defined\n"); + goto out1; + } - if (!mmc) { - printk(DRIVER_NAME "ERROR: no mem for host %d\n", i); - au1xmmc_hosts[i] = 0; - continue; - } + host->ioarea = request_mem_region(r->start, r->end - r->start + 1, + pdev->name); + if (!host->ioarea) { + dev_err(&pdev->dev, "mmio already in use\n"); + goto out1; + } - mmc->ops = &au1xmmc_ops; + host->iobase = (unsigned long)ioremap(r->start, 0x3c); + if (!host->iobase) { + dev_err(&pdev->dev, "cannot remap mmio\n"); + goto out2; + } + + r = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (!r) { + dev_err(&pdev->dev, "no IRQ defined\n"); + goto out3; + } - mmc->f_min = 450000; - mmc->f_max = 24000000; + host->irq = r->start; + /* IRQ is shared among both SD controllers */ + ret = request_irq(host->irq, au1xmmc_irq, IRQF_SHARED, + DRIVER_NAME, host); + if (ret) { + dev_err(&pdev->dev, "cannot grab IRQ\n"); + goto out3; + } - mmc->max_seg_size = AU1XMMC_DESCRIPTOR_SIZE; - mmc->max_phys_segs = AU1XMMC_DESCRIPTOR_COUNT; + mmc->ops = &au1xmmc_ops; - mmc->max_blk_size = 2048; - mmc->max_blk_count = 512; + mmc->f_min = 450000; + mmc->f_max = 24000000; - mmc->ocr_avail = AU1XMMC_OCR; + mmc->max_seg_size = AU1XMMC_DESCRIPTOR_SIZE; + mmc->max_phys_segs = AU1XMMC_DESCRIPTOR_COUNT; - host = mmc_priv(mmc); - host->mmc = mmc; + mmc->max_blk_size = 2048; + mmc->max_blk_count = 512; - host->id = i; - host->iobase = au1xmmc_card_table[host->id].iobase; - host->clock = 0; - host->power_mode = MMC_POWER_OFF; + mmc->ocr_avail = AU1XMMC_OCR; + mmc->caps = 0; - host->flags = au1xmmc_card_inserted(host) ? HOST_F_ACTIVE : 0; - host->status = HOST_S_IDLE; + host->status = HOST_S_IDLE; - init_timer(&host->timer); + /* board-specific carddetect setup, if any */ + if (host->platdata && host->platdata->cd_setup) { + ret = host->platdata->cd_setup(mmc, 1); + if (ret) { + dev_err(&pdev->dev, "board CD setup failed\n"); + goto out4; + } + } else { + /* poll the board-specific is-card-in-socket-? method */ + au1xmmc_init_cd_poll_timer(host); + } - host->timer.function = au1xmmc_poll_event; - host->timer.data = (unsigned long) host; - host->timer.expires = jiffies + AU1XMMC_DETECT_TIMEOUT; + tasklet_init(&host->data_task, au1xmmc_tasklet_data, + (unsigned long)host); - tasklet_init(&host->data_task, au1xmmc_tasklet_data, - (unsigned long) host); + tasklet_init(&host->finish_task, au1xmmc_tasklet_finish, + (unsigned long)host); - tasklet_init(&host->finish_task, au1xmmc_tasklet_finish, - (unsigned long) host); +#ifdef CONFIG_SOC_AU1200 + ret = au1xmmc_dbdma_init(host); + if (ret) + printk(KERN_INFO DRIVER_NAME ": DBDMA init failed; using PIO\n"); +#endif - spin_lock_init(&host->lock); +#ifdef CONFIG_LEDS_CLASS + if (host->platdata && host->platdata->led) { + struct led_classdev *led = host->platdata->led; + led->name = mmc_hostname(mmc); + led->brightness = LED_OFF; + led->default_trigger = mmc_hostname(mmc); + ret = led_classdev_register(mmc_dev(mmc), led); + if (ret) + goto out5; + } +#endif - if (dma != 0) - au1xmmc_init_dma(host); + au1xmmc_reset_controller(host); - au1xmmc_reset_controller(host); + ret = mmc_add_host(mmc); + if (ret) { + dev_err(&pdev->dev, "cannot add mmc host\n"); + goto out6; + } - mmc_add_host(mmc); - au1xmmc_hosts[i] = host; + platform_set_drvdata(pdev, mmc); + /* start the carddetect poll timer if necessary */ + if (!(host->platdata && host->platdata->cd_setup)) add_timer(&host->timer); - printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X (mode=%s)\n", - host->id, host->iobase, dma ? "dma" : "pio"); - } + printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X" + " (mode=%s)\n", pdev->id, host->iobase, + host->flags & HOST_F_DMA ? "dma" : "pio"); - enable_irq(AU1100_SD_IRQ); + return 0; /* all ok */ - return 0; +out6: +#ifdef CONFIG_LEDS_CLASS + if (host->platdata && host->platdata->led) + led_classdev_unregister(host->platdata->led); +out5: +#endif + au_writel(0, HOST_ENABLE(host)); + au_writel(0, HOST_CONFIG(host)); + au_writel(0, HOST_CONFIG2(host)); + au_sync(); + +#ifdef CONFIG_SOC_AU1200 + au1xmmc_dbdma_shutdown(host); +#endif + + tasklet_kill(&host->data_task); + tasklet_kill(&host->finish_task); + + if (host->platdata && host->platdata->cd_setup) + host->platdata->cd_setup(mmc, 0); +out4: + free_irq(host->irq, host); +out3: + iounmap((void *)host->iobase); +out2: + release_resource(host->ioarea); + kfree(host->ioarea); +out1: + mmc_free_host(mmc); +out0: + return ret; } static int __devexit au1xmmc_remove(struct platform_device *pdev) { + struct mmc_host *mmc = platform_get_drvdata(pdev); + struct au1xmmc_host *host; + + if (mmc) { + host = mmc_priv(mmc); + + mmc_remove_host(mmc); - int i; +#ifdef CONFIG_LEDS_CLASS + if (host->platdata && host->platdata->led) + led_classdev_unregister(host->platdata->led); +#endif - disable_irq(AU1100_SD_IRQ); + if (host->platdata && host->platdata->cd_setup) + host->platdata->cd_setup(mmc, 0); + else + del_timer_sync(&host->timer); - for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) { - struct au1xmmc_host *host = au1xmmc_hosts[i]; - if (!host) continue; + au_writel(0, HOST_ENABLE(host)); + au_writel(0, HOST_CONFIG(host)); + au_writel(0, HOST_CONFIG2(host)); + au_sync(); tasklet_kill(&host->data_task); tasklet_kill(&host->finish_task); - del_timer_sync(&host->timer); +#ifdef CONFIG_SOC_AU1200 + au1xmmc_dbdma_shutdown(host); +#endif au1xmmc_set_power(host, 0); - mmc_remove_host(host->mmc); + free_irq(host->irq, host); + iounmap((void *)host->iobase); + release_resource(host->ioarea); + kfree(host->ioarea); - au1xxx_dbdma_chan_free(host->tx_chan); - au1xxx_dbdma_chan_free(host->rx_chan); - - au_writel(0x0, HOST_ENABLE(host)); - au_sync(); + mmc_free_host(mmc); } - - free_irq(AU1100_SD_IRQ, 0); return 0; } @@ -1004,21 +1101,31 @@ static struct platform_driver au1xmmc_driver = { static int __init au1xmmc_init(void) { +#ifdef CONFIG_SOC_AU1200 + /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride + * of 8 bits. And since devices are shared, we need to create + * our own to avoid freaking out other devices. + */ + memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev); + if (!memid) + printk(KERN_ERR "au1xmmc: cannot add memory dbdma dev\n"); +#endif return platform_driver_register(&au1xmmc_driver); } static void __exit au1xmmc_exit(void) { +#ifdef CONFIG_SOC_AU1200 + if (memid) + au1xxx_ddma_del_device(memid); +#endif platform_driver_unregister(&au1xmmc_driver); } module_init(au1xmmc_init); module_exit(au1xmmc_exit); -#ifdef MODULE MODULE_AUTHOR("Advanced Micro Devices, Inc"); MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX"); MODULE_LICENSE("GPL"); MODULE_ALIAS("platform:au1xxx-mmc"); -#endif - diff --git a/drivers/mmc/host/au1xmmc.h b/drivers/mmc/host/au1xmmc.h index 341cbdf..3b40065 100644 --- a/drivers/mmc/host/au1xmmc.h +++ b/drivers/mmc/host/au1xmmc.h @@ -49,8 +49,6 @@ struct au1xmmc_host { struct mmc_host *mmc; struct mmc_request *mrq; - u32 id; - u32 flags; u32 iobase; u32 clock; @@ -73,11 +71,14 @@ struct au1xmmc_host { u32 tx_chan; u32 rx_chan; + int irq; + struct timer_list timer; struct tasklet_struct finish_task; struct tasklet_struct data_task; - - spinlock_t lock; + struct au1xmmc_platform_data *platdata; + struct platform_device *pdev; + struct resource *ioarea; }; /* Status flags used by the host structure */ diff --git a/include/asm-mips/mach-au1x00/au1100_mmc.h b/include/asm-mips/mach-au1x00/au1100_mmc.h index 9e0028f..c35e209 100644 --- a/include/asm-mips/mach-au1x00/au1100_mmc.h +++ b/include/asm-mips/mach-au1x00/au1100_mmc.h @@ -38,15 +38,15 @@ #ifndef __ASM_AU1100_MMC_H #define __ASM_AU1100_MMC_H - -#define NUM_AU1100_MMC_CONTROLLERS 2 - -#if defined(CONFIG_SOC_AU1100) -#define AU1100_SD_IRQ AU1100_SD_INT -#elif defined(CONFIG_SOC_AU1200) -#define AU1100_SD_IRQ AU1200_SD_INT -#endif - +#include + +struct au1xmmc_platform_data { + int(*cd_setup)(void *mmc_host, int on); + int(*card_inserted)(void *mmc_host); + int(*card_readonly)(void *mmc_host); + void(*set_power)(void *mmc_host, int state); + struct led_classdev *led; +}; #define SD0_BASE 0xB0600000 #define SD1_BASE 0xB0680000 -- cgit v1.1 From 281dd23ea03e9893c02d237d9e35a7d20d412452 Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Mon, 9 Jun 2008 08:37:33 +0200 Subject: au1xmmc: enable 4 bit transfer mode Signed-off-by: Manuel Lauss Signed-off-by: Pierre Ossman --- drivers/mmc/host/au1xmmc.c | 22 +++++++++++++++++----- 1 file changed, 17 insertions(+), 5 deletions(-) diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c index d8776d6..2bd4cf4 100644 --- a/drivers/mmc/host/au1xmmc.c +++ b/drivers/mmc/host/au1xmmc.c @@ -95,14 +95,13 @@ static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask) static inline void SEND_STOP(struct au1xmmc_host *host) { - - /* We know the value of CONFIG2, so avoid a read we don't need */ - u32 mask = SD_CONFIG2_EN; + u32 config2; WARN_ON(host->status != HOST_S_DATA); host->status = HOST_S_STOP; - au_writel(mask | SD_CONFIG2_DF, HOST_CONFIG2(host)); + config2 = au_readl(HOST_CONFIG2(host)); + au_writel(config2 | SD_CONFIG2_DF, HOST_CONFIG2(host)); au_sync(); /* Send the stop commmand */ @@ -697,6 +696,7 @@ static void au1xmmc_reset_controller(struct au1xmmc_host *host) static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios) { struct au1xmmc_host *host = mmc_priv(mmc); + u32 config2; if (ios->power_mode == MMC_POWER_OFF) au1xmmc_set_power(host, 0); @@ -708,6 +708,18 @@ static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios) au1xmmc_set_clock(host, ios->clock); host->clock = ios->clock; } + + config2 = au_readl(HOST_CONFIG2(host)); + switch (ios->bus_width) { + case MMC_BUS_WIDTH_4: + config2 |= SD_CONFIG2_WB; + break; + case MMC_BUS_WIDTH_1: + config2 &= ~SD_CONFIG2_WB; + break; + } + au_writel(config2, HOST_CONFIG2(host)); + au_sync(); } #define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT) @@ -952,7 +964,7 @@ static int __devinit au1xmmc_probe(struct platform_device *pdev) mmc->max_blk_count = 512; mmc->ocr_avail = AU1XMMC_OCR; - mmc->caps = 0; + mmc->caps = MMC_CAP_4_BIT_DATA; host->status = HOST_S_IDLE; -- cgit v1.1 From 20f522ff5583a818922b3f650f6f7ef0e3e1aa68 Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Mon, 9 Jun 2008 08:38:03 +0200 Subject: au1xmmc: SDIO IRQ support. Wire up the SD controllers' SDIO IRQ capability. Signed-off-by: Manuel Lauss Signed-off-by: Pierre Ossman --- drivers/mmc/host/au1xmmc.c | 16 +++++++++++++++- 1 file changed, 15 insertions(+), 1 deletion(-) diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c index 2bd4cf4..16b5640 100644 --- a/drivers/mmc/host/au1xmmc.c +++ b/drivers/mmc/host/au1xmmc.c @@ -736,6 +736,9 @@ static irqreturn_t au1xmmc_irq(int irq, void *dev_id) if (!(status & SD_STATUS_I)) return IRQ_NONE; /* not ours */ + if (status & SD_STATUS_SI) /* SDIO */ + mmc_signal_sdio_irq(host->mmc); + if (host->mrq && (status & STATUS_TIMEOUT)) { if (status & SD_STATUS_RAT) host->mrq->cmd->error = -ETIMEDOUT; @@ -862,10 +865,21 @@ static void au1xmmc_dbdma_shutdown(struct au1xmmc_host *host) } #endif +static void au1xmmc_enable_sdio_irq(struct mmc_host *mmc, int en) +{ + struct au1xmmc_host *host = mmc_priv(mmc); + + if (en) + IRQ_ON(host, SD_CONFIG_SI); + else + IRQ_OFF(host, SD_CONFIG_SI); +} + static const struct mmc_host_ops au1xmmc_ops = { .request = au1xmmc_request, .set_ios = au1xmmc_set_ios, .get_ro = au1xmmc_card_readonly, + .enable_sdio_irq = au1xmmc_enable_sdio_irq, }; static void au1xmmc_poll_event(unsigned long arg) @@ -964,7 +978,7 @@ static int __devinit au1xmmc_probe(struct platform_device *pdev) mmc->max_blk_count = 512; mmc->ocr_avail = AU1XMMC_OCR; - mmc->caps = MMC_CAP_4_BIT_DATA; + mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ; host->status = HOST_S_IDLE; -- cgit v1.1 From 5c0a889df56c9f6c5a68ec7aa222082569b35fd9 Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Mon, 9 Jun 2008 08:38:35 +0200 Subject: au1xmmc: codingstyle tidying. Clean up the codebase, no functional changes. - merge the au1xmmc.h header contents into the driver file, - indentation, spelling and style fixes. Signed-off-by: Manuel Lauss Signed-off-by: Pierre Ossman --- drivers/mmc/host/au1xmmc.c | 233 +++++++++++++++++++++++++++------------------ drivers/mmc/host/au1xmmc.h | 97 ------------------- 2 files changed, 141 insertions(+), 189 deletions(-) delete mode 100644 drivers/mmc/host/au1xmmc.h diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c index 16b5640..fcbaf40 100644 --- a/drivers/mmc/host/au1xmmc.c +++ b/drivers/mmc/host/au1xmmc.c @@ -49,20 +49,104 @@ #include #include -#include -#include "au1xmmc.h" - #define DRIVER_NAME "au1xxx-mmc" /* Set this to enable special debugging macros */ /* #define DEBUG */ #ifdef DEBUG -#define DBG(fmt, idx, args...) printk("au1xx(%d): DEBUG: " fmt, idx, ##args) +#define DBG(fmt, idx, args...) \ + printk(KERN_DEBUG "au1xmmc(%d): DEBUG: " fmt, idx, ##args) #else -#define DBG(fmt, idx, args...) +#define DBG(fmt, idx, args...) do {} while (0) #endif +/* Hardware definitions */ +#define AU1XMMC_DESCRIPTOR_COUNT 1 +#define AU1XMMC_DESCRIPTOR_SIZE 2048 + +#define AU1XMMC_OCR (MMC_VDD_27_28 | MMC_VDD_28_29 | MMC_VDD_29_30 | \ + MMC_VDD_30_31 | MMC_VDD_31_32 | MMC_VDD_32_33 | \ + MMC_VDD_33_34 | MMC_VDD_34_35 | MMC_VDD_35_36) + +/* This gives us a hard value for the stop command that we can write directly + * to the command register. + */ +#define STOP_CMD \ + (SD_CMD_RT_1B | SD_CMD_CT_7 | (0xC << SD_CMD_CI_SHIFT) | SD_CMD_GO) + +/* This is the set of interrupts that we configure by default. */ +#define AU1XMMC_INTERRUPTS \ + (SD_CONFIG_SC | SD_CONFIG_DT | SD_CONFIG_RAT | \ + SD_CONFIG_CR | SD_CONFIG_I) + +/* The poll event (looking for insert/remove events runs twice a second. */ +#define AU1XMMC_DETECT_TIMEOUT (HZ/2) + +struct au1xmmc_host { + struct mmc_host *mmc; + struct mmc_request *mrq; + + u32 flags; + u32 iobase; + u32 clock; + u32 bus_width; + u32 power_mode; + + int status; + + struct { + int len; + int dir; + } dma; + + struct { + int index; + int offset; + int len; + } pio; + + u32 tx_chan; + u32 rx_chan; + + int irq; + + struct timer_list timer; + struct tasklet_struct finish_task; + struct tasklet_struct data_task; + struct au1xmmc_platform_data *platdata; + struct platform_device *pdev; + struct resource *ioarea; +}; + +/* Status flags used by the host structure */ +#define HOST_F_XMIT 0x0001 +#define HOST_F_RECV 0x0002 +#define HOST_F_DMA 0x0010 +#define HOST_F_ACTIVE 0x0100 +#define HOST_F_STOP 0x1000 + +#define HOST_S_IDLE 0x0001 +#define HOST_S_CMD 0x0002 +#define HOST_S_DATA 0x0003 +#define HOST_S_STOP 0x0004 + +/* Easy access macros */ +#define HOST_STATUS(h) ((h)->iobase + SD_STATUS) +#define HOST_CONFIG(h) ((h)->iobase + SD_CONFIG) +#define HOST_ENABLE(h) ((h)->iobase + SD_ENABLE) +#define HOST_TXPORT(h) ((h)->iobase + SD_TXPORT) +#define HOST_RXPORT(h) ((h)->iobase + SD_RXPORT) +#define HOST_CMDARG(h) ((h)->iobase + SD_CMDARG) +#define HOST_BLKSIZE(h) ((h)->iobase + SD_BLKSIZE) +#define HOST_CMD(h) ((h)->iobase + SD_CMD) +#define HOST_CONFIG2(h) ((h)->iobase + SD_CONFIG2) +#define HOST_TIMEOUT(h) ((h)->iobase + SD_TIMEOUT) +#define HOST_DEBUG(h) ((h)->iobase + SD_DEBUG) + +#define DMA_CHANNEL(h) \ + (((h)->flags & HOST_F_XMIT) ? (h)->tx_chan : (h)->rx_chan) + static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask) { u32 val = au_readl(HOST_CONFIG(host)); @@ -141,7 +225,6 @@ static int au1xmmc_card_readonly(struct mmc_host *mmc) static void au1xmmc_finish_request(struct au1xmmc_host *host) { - struct mmc_request *mrq = host->mrq; host->mrq = NULL; @@ -215,18 +298,14 @@ static int au1xmmc_send_command(struct au1xmmc_host *host, int wait, au_sync(); /* Wait for the command to go on the line */ - - while(1) { - if (!(au_readl(HOST_CMD(host)) & SD_CMD_GO)) - break; - } + while (au_readl(HOST_CMD(host)) & SD_CMD_GO) + /* nop */; /* Wait for the command to come back */ - if (wait) { u32 status = au_readl(HOST_STATUS(host)); - while(!(status & SD_STATUS_CR)) + while (!(status & SD_STATUS_CR)) status = au_readl(HOST_STATUS(host)); /* Clear the CR status */ @@ -240,12 +319,11 @@ static int au1xmmc_send_command(struct au1xmmc_host *host, int wait, static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) { - struct mmc_request *mrq = host->mrq; struct mmc_data *data; u32 crc; - WARN_ON(host->status != HOST_S_DATA && host->status != HOST_S_STOP); + WARN_ON((host->status != HOST_S_DATA) && (host->status != HOST_S_STOP)); if (host->mrq == NULL) return; @@ -256,15 +334,13 @@ static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) status = au_readl(HOST_STATUS(host)); /* The transaction is really over when the SD_STATUS_DB bit is clear */ - - while((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB)) + while ((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB)) status = au_readl(HOST_STATUS(host)); data->error = 0; dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir); /* Process any errors */ - crc = (status & (SD_STATUS_WC | SD_STATUS_RC)); if (host->flags & HOST_F_XMIT) crc |= ((status & 0x07) == 0x02) ? 0 : 1; @@ -282,15 +358,13 @@ static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) #ifdef CONFIG_SOC_AU1200 /* DBDMA */ u32 chan = DMA_CHANNEL(host); - chan_tab_t *c = *((chan_tab_t **) chan); + chan_tab_t *c = *((chan_tab_t **)chan); au1x_dma_chan_t *cp = c->chan_ptr; data->bytes_xfered = cp->ddma_bytecnt; #endif - } - else + } else data->bytes_xfered = - (data->blocks * data->blksz) - - host->pio.len; + (data->blocks * data->blksz) - host->pio.len; } au1xmmc_finish_request(host); @@ -298,7 +372,7 @@ static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) static void au1xmmc_tasklet_data(unsigned long param) { - struct au1xmmc_host *host = (struct au1xmmc_host *) param; + struct au1xmmc_host *host = (struct au1xmmc_host *)param; u32 status = au_readl(HOST_STATUS(host)); au1xmmc_data_complete(host, status); @@ -308,11 +382,10 @@ static void au1xmmc_tasklet_data(unsigned long param) static void au1xmmc_send_pio(struct au1xmmc_host *host) { - - struct mmc_data *data = 0; - int sg_len, max, count = 0; - unsigned char *sg_ptr; - u32 status = 0; + struct mmc_data *data; + int sg_len, max, count; + unsigned char *sg_ptr, val; + u32 status; struct scatterlist *sg; data = host->mrq->data; @@ -327,14 +400,12 @@ static void au1xmmc_send_pio(struct au1xmmc_host *host) /* This is the space left inside the buffer */ sg_len = data->sg[host->pio.index].length - host->pio.offset; - /* Check to if we need less then the size of the sg_buffer */ - + /* Check if we need less than the size of the sg_buffer */ max = (sg_len > host->pio.len) ? host->pio.len : sg_len; - if (max > AU1XMMC_MAX_TRANSFER) max = AU1XMMC_MAX_TRANSFER; - - for(count = 0; count < max; count++ ) { - unsigned char val; + if (max > AU1XMMC_MAX_TRANSFER) + max = AU1XMMC_MAX_TRANSFER; + for (count = 0; count < max; count++) { status = au_readl(HOST_STATUS(host)); if (!(status & SD_STATUS_TH)) @@ -342,7 +413,7 @@ static void au1xmmc_send_pio(struct au1xmmc_host *host) val = *sg_ptr++; - au_writel((unsigned long) val, HOST_TXPORT(host)); + au_writel((unsigned long)val, HOST_TXPORT(host)); au_sync(); } @@ -366,11 +437,10 @@ static void au1xmmc_send_pio(struct au1xmmc_host *host) static void au1xmmc_receive_pio(struct au1xmmc_host *host) { - - struct mmc_data *data = 0; - int sg_len = 0, max = 0, count = 0; - unsigned char *sg_ptr = 0; - u32 status = 0; + struct mmc_data *data; + int max, count, sg_len = 0; + unsigned char *sg_ptr = NULL; + u32 status, val; struct scatterlist *sg; data = host->mrq->data; @@ -387,15 +457,15 @@ static void au1xmmc_receive_pio(struct au1xmmc_host *host) /* This is the space left inside the buffer */ sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset; - /* Check to if we need less then the size of the sg_buffer */ - if (sg_len < max) max = sg_len; + /* Check if we need less than the size of the sg_buffer */ + if (sg_len < max) + max = sg_len; } if (max > AU1XMMC_MAX_TRANSFER) max = AU1XMMC_MAX_TRANSFER; - for(count = 0; count < max; count++ ) { - u32 val; + for (count = 0; count < max; count++) { status = au_readl(HOST_STATUS(host)); if (!(status & SD_STATUS_NE)) @@ -421,7 +491,7 @@ static void au1xmmc_receive_pio(struct au1xmmc_host *host) val = au_readl(HOST_RXPORT(host)); if (sg_ptr) - *sg_ptr++ = (unsigned char) (val & 0xFF); + *sg_ptr++ = (unsigned char)(val & 0xFF); } host->pio.len -= count; @@ -433,7 +503,7 @@ static void au1xmmc_receive_pio(struct au1xmmc_host *host) } if (host->pio.len == 0) { - //IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF); + /* IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF); */ IRQ_OFF(host, SD_CONFIG_NE); if (host->flags & HOST_F_STOP) @@ -443,17 +513,15 @@ static void au1xmmc_receive_pio(struct au1xmmc_host *host) } } -/* static void au1xmmc_cmd_complete - This is called when a command has been completed - grab the response - and check for errors. Then start the data transfer if it is indicated. -*/ - +/* This is called when a command has been completed - grab the response + * and check for errors. Then start the data transfer if it is indicated. + */ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) { - struct mmc_request *mrq = host->mrq; struct mmc_command *cmd; - int trans; + u32 r[4]; + int i, trans; if (!host->mrq) return; @@ -463,9 +531,6 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) if (cmd->flags & MMC_RSP_PRESENT) { if (cmd->flags & MMC_RSP_136) { - u32 r[4]; - int i; - r[0] = au_readl(host->iobase + SD_RESP3); r[1] = au_readl(host->iobase + SD_RESP2); r[2] = au_readl(host->iobase + SD_RESP1); @@ -473,10 +538,9 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) /* The CRC is omitted from the response, so really * we only got 120 bytes, but the engine expects - * 128 bits, so we have to shift things up + * 128 bits, so we have to shift things up. */ - - for(i = 0; i < 4; i++) { + for (i = 0; i < 4; i++) { cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8; if (i != 3) cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24; @@ -487,22 +551,20 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) * our response omits the CRC, our data ends up * being shifted 8 bits to the right. In this case, * that means that the OSR data starts at bit 31, - * so we can just read RESP0 and return that + * so we can just read RESP0 and return that. */ cmd->resp[0] = au_readl(host->iobase + SD_RESP0); } } /* Figure out errors */ - if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC)) cmd->error = -EILSEQ; trans = host->flags & (HOST_F_XMIT | HOST_F_RECV); if (!trans || cmd->error) { - - IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA|SD_CONFIG_RF); + IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA | SD_CONFIG_RF); tasklet_schedule(&host->finish_task); return; } @@ -529,18 +591,15 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate) { - unsigned int pbus = get_au1x00_speed(); unsigned int divisor; u32 config; /* From databook: - divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1 - */ - + * divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1 + */ pbus /= ((au_readl(SYS_POWERCTRL) & 0x3) + 2); pbus /= 2; - divisor = ((pbus / rate) / 2) - 1; config = au_readl(HOST_CONFIG(host)); @@ -552,8 +611,8 @@ static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate) au_sync(); } -static int -au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) +static int au1xmmc_prepare_data(struct au1xmmc_host *host, + struct mmc_data *data) { int datalen = data->blocks * data->blksz; @@ -582,7 +641,7 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) au1xxx_dbdma_stop(channel); - for(i = 0; i < host->dma.len; i++) { + for (i = 0; i < host->dma.len; i++) { u32 ret = 0, flags = DDMA_FLAGS_NOIE; struct scatterlist *sg = &data->sg[i]; int sg_len = sg->length; @@ -592,14 +651,12 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) if (i == host->dma.len - 1) flags = DDMA_FLAGS_IE; - if (host->flags & HOST_F_XMIT){ - ret = au1xxx_dbdma_put_source_flags(channel, - (void *) sg_virt(sg), len, flags); - } - else { - ret = au1xxx_dbdma_put_dest_flags(channel, - (void *) sg_virt(sg), - len, flags); + if (host->flags & HOST_F_XMIT) { + ret = au1xxx_dbdma_put_source_flags(channel, + (void *)sg_virt(sg), len, flags); + } else { + ret = au1xxx_dbdma_put_dest_flags(channel, + (void *)sg_virt(sg), len, flags); } if (!ret) @@ -608,8 +665,7 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) datalen -= len; } #endif - } - else { + } else { host->pio.index = 0; host->pio.offset = 0; host->pio.len = datalen; @@ -618,7 +674,7 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) IRQ_ON(host, SD_CONFIG_TH); else IRQ_ON(host, SD_CONFIG_NE); - //IRQ_ON(host, SD_CONFIG_RA|SD_CONFIG_RF); + /* IRQ_ON(host, SD_CONFIG_RA | SD_CONFIG_RF); */ } return 0; @@ -629,15 +685,10 @@ dataerr: return -ETIMEDOUT; } -/* static void au1xmmc_request - This actually starts a command or data transaction -*/ - +/* This actually starts a command or data transaction */ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) { - struct au1xmmc_host *host = mmc_priv(mmc); - unsigned int flags = 0; int ret = 0; WARN_ON(irqs_disabled()); @@ -648,7 +699,6 @@ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) if (mrq->data) { FLUSH_FIFO(host); - flags = mrq->data->flags; ret = au1xmmc_prepare_data(host, mrq->data); } @@ -663,7 +713,6 @@ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) static void au1xmmc_reset_controller(struct au1xmmc_host *host) { - /* Apply the clock */ au_writel(SD_ENABLE_CE, HOST_ENABLE(host)); au_sync_delay(1); @@ -693,7 +742,7 @@ static void au1xmmc_reset_controller(struct au1xmmc_host *host) } -static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios) +static void au1xmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) { struct au1xmmc_host *host = mmc_priv(mmc); u32 config2; diff --git a/drivers/mmc/host/au1xmmc.h b/drivers/mmc/host/au1xmmc.h deleted file mode 100644 index 3b40065..0000000 --- a/drivers/mmc/host/au1xmmc.h +++ /dev/null @@ -1,97 +0,0 @@ -#ifndef _AU1XMMC_H_ -#define _AU1XMMC_H_ - -/* Hardware definitions */ - -#define AU1XMMC_DESCRIPTOR_COUNT 1 -#define AU1XMMC_DESCRIPTOR_SIZE 2048 - -#define AU1XMMC_OCR ( MMC_VDD_27_28 | MMC_VDD_28_29 | MMC_VDD_29_30 | \ - MMC_VDD_30_31 | MMC_VDD_31_32 | MMC_VDD_32_33 | \ - MMC_VDD_33_34 | MMC_VDD_34_35 | MMC_VDD_35_36) - -/* Easy access macros */ - -#define HOST_STATUS(h) ((h)->iobase + SD_STATUS) -#define HOST_CONFIG(h) ((h)->iobase + SD_CONFIG) -#define HOST_ENABLE(h) ((h)->iobase + SD_ENABLE) -#define HOST_TXPORT(h) ((h)->iobase + SD_TXPORT) -#define HOST_RXPORT(h) ((h)->iobase + SD_RXPORT) -#define HOST_CMDARG(h) ((h)->iobase + SD_CMDARG) -#define HOST_BLKSIZE(h) ((h)->iobase + SD_BLKSIZE) -#define HOST_CMD(h) ((h)->iobase + SD_CMD) -#define HOST_CONFIG2(h) ((h)->iobase + SD_CONFIG2) -#define HOST_TIMEOUT(h) ((h)->iobase + SD_TIMEOUT) -#define HOST_DEBUG(h) ((h)->iobase + SD_DEBUG) - -#define DMA_CHANNEL(h) \ - ( ((h)->flags & HOST_F_XMIT) ? (h)->tx_chan : (h)->rx_chan) - -/* This gives us a hard value for the stop command that we can write directly - * to the command register - */ - -#define STOP_CMD (SD_CMD_RT_1B|SD_CMD_CT_7|(0xC << SD_CMD_CI_SHIFT)|SD_CMD_GO) - -/* This is the set of interrupts that we configure by default */ - -#if 0 -#define AU1XMMC_INTERRUPTS (SD_CONFIG_SC | SD_CONFIG_DT | SD_CONFIG_DD | \ - SD_CONFIG_RAT | SD_CONFIG_CR | SD_CONFIG_I) -#endif - -#define AU1XMMC_INTERRUPTS (SD_CONFIG_SC | SD_CONFIG_DT | \ - SD_CONFIG_RAT | SD_CONFIG_CR | SD_CONFIG_I) -/* The poll event (looking for insert/remove events runs twice a second */ -#define AU1XMMC_DETECT_TIMEOUT (HZ/2) - -struct au1xmmc_host { - struct mmc_host *mmc; - struct mmc_request *mrq; - - u32 flags; - u32 iobase; - u32 clock; - u32 bus_width; - u32 power_mode; - - int status; - - struct { - int len; - int dir; - } dma; - - struct { - int index; - int offset; - int len; - } pio; - - u32 tx_chan; - u32 rx_chan; - - int irq; - - struct timer_list timer; - struct tasklet_struct finish_task; - struct tasklet_struct data_task; - struct au1xmmc_platform_data *platdata; - struct platform_device *pdev; - struct resource *ioarea; -}; - -/* Status flags used by the host structure */ - -#define HOST_F_XMIT 0x0001 -#define HOST_F_RECV 0x0002 -#define HOST_F_DMA 0x0010 -#define HOST_F_ACTIVE 0x0100 -#define HOST_F_STOP 0x1000 - -#define HOST_S_IDLE 0x0001 -#define HOST_S_CMD 0x0002 -#define HOST_S_DATA 0x0003 -#define HOST_S_STOP 0x0004 - -#endif -- cgit v1.1 From 88b8d9a83431237bf3eec1f2968f763607811171 Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Mon, 9 Jun 2008 08:39:11 +0200 Subject: au1xmmc: abort requests early if no card is present. Don't process an MMC request if no card is present. Signed-off-by: Manuel Lauss Signed-off-by: Pierre Ossman --- drivers/mmc/host/au1xmmc.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c index fcbaf40..718eb87 100644 --- a/drivers/mmc/host/au1xmmc.c +++ b/drivers/mmc/host/au1xmmc.c @@ -697,6 +697,13 @@ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) host->mrq = mrq; host->status = HOST_S_CMD; + /* fail request immediately if no card is present */ + if (0 == au1xmmc_card_inserted(host)) { + mrq->cmd->error = -ENOMEDIUM; + au1xmmc_finish_request(host); + return; + } + if (mrq->data) { FLUSH_FIFO(host); ret = au1xmmc_prepare_data(host, mrq->data); -- cgit v1.1 From 08fcb7208c4a8913232e48931783270262ece954 Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Mon, 9 Jun 2008 08:40:35 +0200 Subject: au1xmmc: new maintainer. Signed-off-by: Manuel Lauss Signed-off-by: Pierre Ossman --- MAINTAINERS | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index 1528e58..f140449 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -348,7 +348,9 @@ W: http://www.linux-usb.org/SpeedTouch/ S: Maintained ALCHEMY AU1XX0 MMC DRIVER -S: Orphan +P: Manuel Lauss +M: manuel.lauss@gmail.com +S: Maintained ALI1563 I2C DRIVER P: Rudolf Marek -- cgit v1.1 From e2d2647702702ea08cb78cdc9eca8c24242aa9be Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Fri, 27 Jun 2008 18:25:18 +0200 Subject: au1xmmc: remove custom carddetect poll implementation. The MMC core provides a carddetect poll feature, time to remove the driver's own implementation of it. Signed-off-by: Manuel Lauss Signed-off-by: Pierre Ossman --- drivers/mmc/host/au1xmmc.c | 79 +++++++++++----------------------------------- 1 file changed, 18 insertions(+), 61 deletions(-) diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c index 718eb87..3f15eb2 100644 --- a/drivers/mmc/host/au1xmmc.c +++ b/drivers/mmc/host/au1xmmc.c @@ -21,7 +21,7 @@ * published by the Free Software Foundation. */ -/* Why is a timer used to detect insert events? +/* Why don't we use the SD controllers' carddetect feature? * * From the AU1100 MMC application guide: * If the Au1100-based design is intended to support both MultiMediaCards @@ -30,8 +30,6 @@ * In doing so, a MMC card never enters SPI-mode communications, * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective * (the low to high transition will not occur). - * - * So we use the timer to check the status manually. */ #include @@ -111,7 +109,6 @@ struct au1xmmc_host { int irq; - struct timer_list timer; struct tasklet_struct finish_task; struct tasklet_struct data_task; struct au1xmmc_platform_data *platdata; @@ -198,29 +195,24 @@ static void au1xmmc_set_power(struct au1xmmc_host *host, int state) host->platdata->set_power(host->mmc, state); } -static int au1xmmc_card_inserted(struct au1xmmc_host *host) +static int au1xmmc_card_inserted(struct mmc_host *mmc) { - int ret; + struct au1xmmc_host *host = mmc_priv(mmc); if (host->platdata && host->platdata->card_inserted) - ret = host->platdata->card_inserted(host->mmc); - else - ret = 1; /* assume there is a card */ + return !!host->platdata->card_inserted(host->mmc); - return ret; + return -ENOSYS; } static int au1xmmc_card_readonly(struct mmc_host *mmc) { struct au1xmmc_host *host = mmc_priv(mmc); - int ret; if (host->platdata && host->platdata->card_readonly) - ret = host->platdata->card_readonly(mmc); - else - ret = 0; /* assume card is read-write */ + return !!host->platdata->card_readonly(mmc); - return ret; + return -ENOSYS; } static void au1xmmc_finish_request(struct au1xmmc_host *host) @@ -698,7 +690,7 @@ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) host->status = HOST_S_CMD; /* fail request immediately if no card is present */ - if (0 == au1xmmc_card_inserted(host)) { + if (0 == au1xmmc_card_inserted(mmc)) { mrq->cmd->error = -ENOMEDIUM; au1xmmc_finish_request(host); return; @@ -935,39 +927,10 @@ static const struct mmc_host_ops au1xmmc_ops = { .request = au1xmmc_request, .set_ios = au1xmmc_set_ios, .get_ro = au1xmmc_card_readonly, + .get_cd = au1xmmc_card_inserted, .enable_sdio_irq = au1xmmc_enable_sdio_irq, }; -static void au1xmmc_poll_event(unsigned long arg) -{ - struct au1xmmc_host *host = (struct au1xmmc_host *)arg; - int card = au1xmmc_card_inserted(host); - int controller = (host->flags & HOST_F_ACTIVE) ? 1 : 0; - - if (card != controller) { - host->flags &= ~HOST_F_ACTIVE; - if (card) - host->flags |= HOST_F_ACTIVE; - mmc_detect_change(host->mmc, 0); - } - -#ifdef DEBUG - if (host->mrq != NULL) { - u32 status = au_readl(HOST_STATUS(host)); - DBG("PENDING - %8.8x\n", host->pdev->id, status); - } -#endif - mod_timer(&host->timer, jiffies + AU1XMMC_DETECT_TIMEOUT); -} - -static void au1xmmc_init_cd_poll_timer(struct au1xmmc_host *host) -{ - init_timer(&host->timer); - host->timer.function = au1xmmc_poll_event; - host->timer.data = (unsigned long)host; - host->timer.expires = jiffies + AU1XMMC_DETECT_TIMEOUT; -} - static int __devinit au1xmmc_probe(struct platform_device *pdev) { struct mmc_host *mmc; @@ -1042,13 +1005,11 @@ static int __devinit au1xmmc_probe(struct platform_device *pdev) if (host->platdata && host->platdata->cd_setup) { ret = host->platdata->cd_setup(mmc, 1); if (ret) { - dev_err(&pdev->dev, "board CD setup failed\n"); - goto out4; + dev_warn(&pdev->dev, "board CD setup failed\n"); + mmc->caps |= MMC_CAP_NEEDS_POLL; } - } else { - /* poll the board-specific is-card-in-socket-? method */ - au1xmmc_init_cd_poll_timer(host); - } + } else + mmc->caps |= MMC_CAP_NEEDS_POLL; tasklet_init(&host->data_task, au1xmmc_tasklet_data, (unsigned long)host); @@ -1084,10 +1045,6 @@ static int __devinit au1xmmc_probe(struct platform_device *pdev) platform_set_drvdata(pdev, mmc); - /* start the carddetect poll timer if necessary */ - if (!(host->platdata && host->platdata->cd_setup)) - add_timer(&host->timer); - printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X" " (mode=%s)\n", pdev->id, host->iobase, host->flags & HOST_F_DMA ? "dma" : "pio"); @@ -1112,9 +1069,10 @@ out5: tasklet_kill(&host->data_task); tasklet_kill(&host->finish_task); - if (host->platdata && host->platdata->cd_setup) + if (host->platdata && host->platdata->cd_setup && + !(mmc->caps & MMC_CAP_NEEDS_POLL)) host->platdata->cd_setup(mmc, 0); -out4: + free_irq(host->irq, host); out3: iounmap((void *)host->iobase); @@ -1142,10 +1100,9 @@ static int __devexit au1xmmc_remove(struct platform_device *pdev) led_classdev_unregister(host->platdata->led); #endif - if (host->platdata && host->platdata->cd_setup) + if (host->platdata && host->platdata->cd_setup && + !(mmc->caps & MMC_CAP_NEEDS_POLL)) host->platdata->cd_setup(mmc, 0); - else - del_timer_sync(&host->timer); au_writel(0, HOST_ENABLE(host)); au_writel(0, HOST_CONFIG(host)); -- cgit v1.1 From ad3868b2ec96ec14a1549c9e33f5f9a2a3c6ab15 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sat, 28 Jun 2008 12:52:45 +0200 Subject: mmc,sdio: helper function for transfer padding There are a lot of crappy controllers out there that cannot handle all the request sizes that the MMC/SD/SDIO specifications require. In case the card driver can pad the data to overcome the problems, this commit adds a helper that calculates how much that padding should be. A corresponding helper is also added for SDIO, but it can also deal with all the complexities of splitting up a large transfer efficiently. Signed-off-by: Pierre Ossman --- drivers/mmc/core/core.c | 29 +++++++++- drivers/mmc/core/sdio_io.c | 99 ++++++++++++++++++++++++++++++++- drivers/net/wireless/libertas/if_sdio.c | 20 +++---- include/linux/mmc/core.h | 1 + include/linux/mmc/sdio_func.h | 4 +- 5 files changed, 137 insertions(+), 16 deletions(-) diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index ede5d1e..3ee5b8c 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -3,7 +3,7 @@ * * Copyright (C) 2003-2004 Russell King, All Rights Reserved. * SD support Copyright (C) 2004 Ian Molton, All Rights Reserved. - * Copyright (C) 2005-2007 Pierre Ossman, All Rights Reserved. + * Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved. * MMCv4 support Copyright (C) 2006 Philip Langdale, All Rights Reserved. * * This program is free software; you can redistribute it and/or modify @@ -295,6 +295,33 @@ void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card) EXPORT_SYMBOL(mmc_set_data_timeout); /** + * mmc_align_data_size - pads a transfer size to a more optimal value + * @card: the MMC card associated with the data transfer + * @sz: original transfer size + * + * Pads the original data size with a number of extra bytes in + * order to avoid controller bugs and/or performance hits + * (e.g. some controllers revert to PIO for certain sizes). + * + * Returns the improved size, which might be unmodified. + * + * Note that this function is only relevant when issuing a + * single scatter gather entry. + */ +unsigned int mmc_align_data_size(struct mmc_card *card, unsigned int sz) +{ + /* + * FIXME: We don't have a system for the controller to tell + * the core about its problems yet, so for now we just 32-bit + * align the size. + */ + sz = ((sz + 3) / 4) * 4; + + return sz; +} +EXPORT_SYMBOL(mmc_align_data_size); + +/** * __mmc_claim_host - exclusively claim a host * @host: mmc host to claim * @abort: whether or not the operation should be aborted diff --git a/drivers/mmc/core/sdio_io.c b/drivers/mmc/core/sdio_io.c index 625b92c..6ee7861 100644 --- a/drivers/mmc/core/sdio_io.c +++ b/drivers/mmc/core/sdio_io.c @@ -1,7 +1,7 @@ /* * linux/drivers/mmc/core/sdio_io.c * - * Copyright 2007 Pierre Ossman + * Copyright 2007-2008 Pierre Ossman * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -189,6 +189,103 @@ int sdio_set_block_size(struct sdio_func *func, unsigned blksz) EXPORT_SYMBOL_GPL(sdio_set_block_size); +/** + * sdio_align_size - pads a transfer size to a more optimal value + * @func: SDIO function + * @sz: original transfer size + * + * Pads the original data size with a number of extra bytes in + * order to avoid controller bugs and/or performance hits + * (e.g. some controllers revert to PIO for certain sizes). + * + * If possible, it will also adjust the size so that it can be + * handled in just a single request. + * + * Returns the improved size, which might be unmodified. + */ +unsigned int sdio_align_size(struct sdio_func *func, unsigned int sz) +{ + unsigned int orig_sz; + unsigned int blk_sz, byte_sz; + unsigned chunk_sz; + + orig_sz = sz; + + /* + * Do a first check with the controller, in case it + * wants to increase the size up to a point where it + * might need more than one block. + */ + sz = mmc_align_data_size(func->card, sz); + + /* + * If we can still do this with just a byte transfer, then + * we're done. + */ + if ((sz <= func->cur_blksize) && (sz <= 512)) + return sz; + + if (func->card->cccr.multi_block) { + /* + * Check if the transfer is already block aligned + */ + if ((sz % func->cur_blksize) == 0) + return sz; + + /* + * Realign it so that it can be done with one request, + * and recheck if the controller still likes it. + */ + blk_sz = ((sz + func->cur_blksize - 1) / + func->cur_blksize) * func->cur_blksize; + blk_sz = mmc_align_data_size(func->card, blk_sz); + + /* + * This value is only good if it is still just + * one request. + */ + if ((blk_sz % func->cur_blksize) == 0) + return blk_sz; + + /* + * We failed to do one request, but at least try to + * pad the remainder properly. + */ + byte_sz = mmc_align_data_size(func->card, + sz % func->cur_blksize); + if ((byte_sz <= func->cur_blksize) && (byte_sz <= 512)) { + blk_sz = sz / func->cur_blksize; + return blk_sz * func->cur_blksize + byte_sz; + } + } else { + /* + * We need multiple requests, so first check that the + * controller can handle the chunk size; + */ + chunk_sz = mmc_align_data_size(func->card, + min(func->cur_blksize, 512u)); + if (chunk_sz == min(func->cur_blksize, 512u)) { + /* + * Fix up the size of the remainder (if any) + */ + byte_sz = orig_sz % chunk_sz; + if (byte_sz) { + byte_sz = mmc_align_data_size(func->card, + byte_sz); + } + + return (orig_sz / chunk_sz) * chunk_sz + byte_sz; + } + } + + /* + * The controller is simply incapable of transferring the size + * we want in decent manner, so just return the original size. + */ + return orig_sz; +} +EXPORT_SYMBOL_GPL(sdio_align_size); + /* Split an arbitrarily sized data transfer into several * IO_RW_EXTENDED commands. */ static int sdio_io_rw_ext_helper(struct sdio_func *func, int write, diff --git a/drivers/net/wireless/libertas/if_sdio.c b/drivers/net/wireless/libertas/if_sdio.c index 3dd537b..b54e2ea 100644 --- a/drivers/net/wireless/libertas/if_sdio.c +++ b/drivers/net/wireless/libertas/if_sdio.c @@ -1,7 +1,7 @@ /* * linux/drivers/net/wireless/libertas/if_sdio.c * - * Copyright 2007 Pierre Ossman + * Copyright 2007-2008 Pierre Ossman * * Inspired by if_cs.c, Copyright 2007 Holger Schurig * @@ -266,13 +266,10 @@ static int if_sdio_card_to_host(struct if_sdio_card *card) /* * The transfer must be in one transaction or the firmware - * goes suicidal. + * goes suicidal. There's no way to guarantee that for all + * controllers, but we can at least try. */ - chunk = size; - if ((chunk > card->func->cur_blksize) || (chunk > 512)) { - chunk = (chunk + card->func->cur_blksize - 1) / - card->func->cur_blksize * card->func->cur_blksize; - } + chunk = sdio_align_size(card->func, size); ret = sdio_readsb(card->func, card->buffer, card->ioport, chunk); if (ret) @@ -696,13 +693,10 @@ static int if_sdio_host_to_card(struct lbs_private *priv, /* * The transfer must be in one transaction or the firmware - * goes suicidal. + * goes suicidal. There's no way to guarantee that for all + * controllers, but we can at least try. */ - size = nb + 4; - if ((size > card->func->cur_blksize) || (size > 512)) { - size = (size + card->func->cur_blksize - 1) / - card->func->cur_blksize * card->func->cur_blksize; - } + size = sdio_align_size(card->func, nb + 4); packet = kzalloc(sizeof(struct if_sdio_packet) + size, GFP_ATOMIC); diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h index d0c3abe..143cebf 100644 --- a/include/linux/mmc/core.h +++ b/include/linux/mmc/core.h @@ -135,6 +135,7 @@ extern int mmc_wait_for_app_cmd(struct mmc_host *, struct mmc_card *, struct mmc_command *, int); extern void mmc_set_data_timeout(struct mmc_data *, const struct mmc_card *); +extern unsigned int mmc_align_data_size(struct mmc_card *, unsigned int); extern int __mmc_claim_host(struct mmc_host *host, atomic_t *abort); extern void mmc_release_host(struct mmc_host *host); diff --git a/include/linux/mmc/sdio_func.h b/include/linux/mmc/sdio_func.h index b050f4d..f57f22b 100644 --- a/include/linux/mmc/sdio_func.h +++ b/include/linux/mmc/sdio_func.h @@ -1,7 +1,7 @@ /* * include/linux/mmc/sdio_func.h * - * Copyright 2007 Pierre Ossman + * Copyright 2007-2008 Pierre Ossman * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -120,6 +120,8 @@ extern int sdio_set_block_size(struct sdio_func *func, unsigned blksz); extern int sdio_claim_irq(struct sdio_func *func, sdio_irq_handler_t *handler); extern int sdio_release_irq(struct sdio_func *func); +extern unsigned int sdio_align_size(struct sdio_func *func, unsigned int sz); + extern unsigned char sdio_readb(struct sdio_func *func, unsigned int addr, int *err_ret); extern unsigned short sdio_readw(struct sdio_func *func, -- cgit v1.1 From eea0f581c4e596e02250df230f8d385827977964 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sat, 28 Jun 2008 13:22:40 +0200 Subject: sdio: clean up handling of byte mode transfer size Make sure that the maximum size for a byte mode transfer is identical in all places. Also tweak the transfer helper so that a single byte mode transfer is preferred over (possibly multiple) block mode request(s). Signed-off-by: Pierre Ossman --- drivers/mmc/core/sdio_io.c | 29 ++++++++++++++++++----------- 1 file changed, 18 insertions(+), 11 deletions(-) diff --git a/drivers/mmc/core/sdio_io.c b/drivers/mmc/core/sdio_io.c index 6ee7861..cc42a41 100644 --- a/drivers/mmc/core/sdio_io.c +++ b/drivers/mmc/core/sdio_io.c @@ -186,9 +186,20 @@ int sdio_set_block_size(struct sdio_func *func, unsigned blksz) func->cur_blksize = blksz; return 0; } - EXPORT_SYMBOL_GPL(sdio_set_block_size); +/* + * Calculate the maximum byte mode transfer size + */ +static inline unsigned int sdio_max_byte_size(struct sdio_func *func) +{ + return min(min(min( + func->card->host->max_seg_size, + func->card->host->max_blk_size), + func->max_blksize), + 512u); /* maximum size for byte mode */ +} + /** * sdio_align_size - pads a transfer size to a more optimal value * @func: SDIO function @@ -222,7 +233,7 @@ unsigned int sdio_align_size(struct sdio_func *func, unsigned int sz) * If we can still do this with just a byte transfer, then * we're done. */ - if ((sz <= func->cur_blksize) && (sz <= 512)) + if (sz <= sdio_max_byte_size(func)) return sz; if (func->card->cccr.multi_block) { @@ -253,7 +264,7 @@ unsigned int sdio_align_size(struct sdio_func *func, unsigned int sz) */ byte_sz = mmc_align_data_size(func->card, sz % func->cur_blksize); - if ((byte_sz <= func->cur_blksize) && (byte_sz <= 512)) { + if (byte_sz <= sdio_max_byte_size(func)) { blk_sz = sz / func->cur_blksize; return blk_sz * func->cur_blksize + byte_sz; } @@ -263,8 +274,8 @@ unsigned int sdio_align_size(struct sdio_func *func, unsigned int sz) * controller can handle the chunk size; */ chunk_sz = mmc_align_data_size(func->card, - min(func->cur_blksize, 512u)); - if (chunk_sz == min(func->cur_blksize, 512u)) { + sdio_max_byte_size(func)); + if (chunk_sz == sdio_max_byte_size(func)) { /* * Fix up the size of the remainder (if any) */ @@ -296,7 +307,7 @@ static int sdio_io_rw_ext_helper(struct sdio_func *func, int write, int ret; /* Do the bulk of the transfer using block mode (if supported). */ - if (func->card->cccr.multi_block) { + if (func->card->cccr.multi_block && (size > sdio_max_byte_size(func))) { /* Blocks per command is limited by host count, host transfer * size (we only use a single sg entry) and the maximum for * IO_RW_EXTENDED of 511 blocks. */ @@ -328,11 +339,7 @@ static int sdio_io_rw_ext_helper(struct sdio_func *func, int write, /* Write the remainder using byte mode. */ while (remainder > 0) { - size = remainder; - if (size > func->cur_blksize) - size = func->cur_blksize; - if (size > 512) - size = 512; /* maximum size for byte mode */ + size = min(remainder, sdio_max_byte_size(func)); ret = mmc_io_rw_extended(func->card, write, func->num, addr, incr_addr, buf, 1, size); -- cgit v1.1 From 0121a9829bf28c65e1a05cc881899c10d82b8de2 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sat, 28 Jun 2008 17:51:27 +0200 Subject: mmc_test: only bind to supported cards We can only perform the tests on MMC and SD cards, so avoid binding to any other type. Signed-off-by: Pierre Ossman --- drivers/mmc/card/mmc_test.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/mmc/card/mmc_test.c b/drivers/mmc/card/mmc_test.c index 371d922..8e0bb12 100644 --- a/drivers/mmc/card/mmc_test.c +++ b/drivers/mmc/card/mmc_test.c @@ -1,7 +1,7 @@ /* * linux/drivers/mmc/card/mmc_test.c * - * Copyright 2007 Pierre Ossman + * Copyright 2007-2008 Pierre Ossman * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -858,6 +858,9 @@ static int mmc_test_probe(struct mmc_card *card) { int ret; + if ((card->type != MMC_TYPE_MMC) && (card->type != MMC_TYPE_SD)) + return -ENODEV; + mutex_init(&mmc_test_lock); ret = device_create_file(&card->dev, &dev_attr_test); -- cgit v1.1 From 93fc48c785f6266e67663b3cbbf24579b53fe5cf Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sat, 28 Jun 2008 18:21:41 +0200 Subject: sdhci-pci: don't penalize newer jmicron chips The upcoming JMicron chips will have solved all the currently known bugs, so don't penalize them for older problems. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci-pci.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index c0fbf48..0716dcf 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -139,6 +139,12 @@ static int jmicron_probe(struct sdhci_pci_chip *chip) { int ret; + if (chip->pdev->revision == 0) { + chip->quirks |= SDHCI_QUIRK_32BIT_DMA_ADDR | + SDHCI_QUIRK_32BIT_DMA_SIZE | + SDHCI_QUIRK_RESET_AFTER_REQUEST; + } + /* * JMicron chips can have two interfaces to the same hardware * in order to work around limitations in Microsoft's driver. @@ -250,10 +256,6 @@ static int jmicron_resume(struct sdhci_pci_chip *chip) } static const struct sdhci_pci_fixes sdhci_jmicron = { - .quirks = SDHCI_QUIRK_32BIT_DMA_ADDR | - SDHCI_QUIRK_32BIT_DMA_SIZE | - SDHCI_QUIRK_RESET_AFTER_REQUEST, - .probe = jmicron_probe, .probe_slot = jmicron_probe_slot, -- cgit v1.1 From 2134a922c6e75c779983cad5d8aae832275f5a0d Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sat, 28 Jun 2008 18:28:51 +0200 Subject: sdhci: scatter-gather (ADMA) support Add support for the scatter-gather DMA mode present on newer controllers. As the mode requires 32-bit alignment, non-aligned chunks are handled by using a bounce buffer. Also add some new quirks to handle controllers that have bugs in the ADMA engine. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci-pci.c | 17 ++ drivers/mmc/host/sdhci.c | 383 +++++++++++++++++++++++++++++++++++++++---- drivers/mmc/host/sdhci.h | 51 +++++- 3 files changed, 407 insertions(+), 44 deletions(-) diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index 0716dcf..deb607c 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -142,6 +142,7 @@ static int jmicron_probe(struct sdhci_pci_chip *chip) if (chip->pdev->revision == 0) { chip->quirks |= SDHCI_QUIRK_32BIT_DMA_ADDR | SDHCI_QUIRK_32BIT_DMA_SIZE | + SDHCI_QUIRK_32BIT_ADMA_SIZE | SDHCI_QUIRK_RESET_AFTER_REQUEST; } @@ -206,6 +207,22 @@ static void jmicron_enable_mmc(struct sdhci_host *host, int on) static int jmicron_probe_slot(struct sdhci_pci_slot *slot) { + if (slot->chip->pdev->revision == 0) { + u16 version; + + version = readl(slot->host->ioaddr + SDHCI_HOST_VERSION); + version = (version & SDHCI_VENDOR_VER_MASK) >> + SDHCI_VENDOR_VER_SHIFT; + + /* + * Older versions of the chip have lots of nasty glitches + * in the ADMA engine. It's best just to avoid it + * completely. + */ + if (version < 0xAC) + slot->host->quirks |= SDHCI_QUIRK_BROKEN_ADMA; + } + /* * The secondary interface requires a bit set to get the * interrupts. diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 0ab582e..b802044 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -124,7 +124,8 @@ static void sdhci_init(struct sdhci_host *host) SDHCI_INT_END_BIT | SDHCI_INT_CRC | SDHCI_INT_TIMEOUT | SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT | SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | - SDHCI_INT_DMA_END | SDHCI_INT_DATA_END | SDHCI_INT_RESPONSE; + SDHCI_INT_DMA_END | SDHCI_INT_DATA_END | SDHCI_INT_RESPONSE | + SDHCI_INT_ADMA_ERROR; writel(intmask, host->ioaddr + SDHCI_INT_ENABLE); writel(intmask, host->ioaddr + SDHCI_SIGNAL_ENABLE); @@ -314,6 +315,196 @@ static void sdhci_transfer_pio(struct sdhci_host *host) DBG("PIO transfer complete.\n"); } +static char *sdhci_kmap_atomic(struct scatterlist *sg, unsigned long *flags) +{ + local_irq_save(*flags); + return kmap_atomic(sg_page(sg), KM_BIO_SRC_IRQ) + sg->offset; +} + +static void sdhci_kunmap_atomic(void *buffer, unsigned long *flags) +{ + kunmap_atomic(buffer, KM_BIO_SRC_IRQ); + local_irq_restore(*flags); +} + +static void sdhci_adma_table_pre(struct sdhci_host *host, + struct mmc_data *data) +{ + int direction; + + u8 *desc; + u8 *align; + dma_addr_t addr; + dma_addr_t align_addr; + int len, offset; + + struct scatterlist *sg; + int i; + char *buffer; + unsigned long flags; + + /* + * The spec does not specify endianness of descriptor table. + * We currently guess that it is LE. + */ + + if (data->flags & MMC_DATA_READ) + direction = DMA_FROM_DEVICE; + else + direction = DMA_TO_DEVICE; + + /* + * The ADMA descriptor table is mapped further down as we + * need to fill it with data first. + */ + + host->align_addr = dma_map_single(mmc_dev(host->mmc), + host->align_buffer, 128 * 4, direction); + BUG_ON(host->align_addr & 0x3); + + host->sg_count = dma_map_sg(mmc_dev(host->mmc), + data->sg, data->sg_len, direction); + + desc = host->adma_desc; + align = host->align_buffer; + + align_addr = host->align_addr; + + for_each_sg(data->sg, sg, host->sg_count, i) { + addr = sg_dma_address(sg); + len = sg_dma_len(sg); + + /* + * The SDHCI specification states that ADMA + * addresses must be 32-bit aligned. If they + * aren't, then we use a bounce buffer for + * the (up to three) bytes that screw up the + * alignment. + */ + offset = (4 - (addr & 0x3)) & 0x3; + if (offset) { + if (data->flags & MMC_DATA_WRITE) { + buffer = sdhci_kmap_atomic(sg, &flags); + memcpy(align, buffer, offset); + sdhci_kunmap_atomic(buffer, &flags); + } + + desc[7] = (align_addr >> 24) & 0xff; + desc[6] = (align_addr >> 16) & 0xff; + desc[5] = (align_addr >> 8) & 0xff; + desc[4] = (align_addr >> 0) & 0xff; + + BUG_ON(offset > 65536); + + desc[3] = (offset >> 8) & 0xff; + desc[2] = (offset >> 0) & 0xff; + + desc[1] = 0x00; + desc[0] = 0x21; /* tran, valid */ + + align += 4; + align_addr += 4; + + desc += 8; + + addr += offset; + len -= offset; + } + + desc[7] = (addr >> 24) & 0xff; + desc[6] = (addr >> 16) & 0xff; + desc[5] = (addr >> 8) & 0xff; + desc[4] = (addr >> 0) & 0xff; + + BUG_ON(len > 65536); + + desc[3] = (len >> 8) & 0xff; + desc[2] = (len >> 0) & 0xff; + + desc[1] = 0x00; + desc[0] = 0x21; /* tran, valid */ + + desc += 8; + + /* + * If this triggers then we have a calculation bug + * somewhere. :/ + */ + WARN_ON((desc - host->adma_desc) > (128 * 2 + 1) * 4); + } + + /* + * Add a terminating entry. + */ + desc[7] = 0; + desc[6] = 0; + desc[5] = 0; + desc[4] = 0; + + desc[3] = 0; + desc[2] = 0; + + desc[1] = 0x00; + desc[0] = 0x03; /* nop, end, valid */ + + /* + * Resync align buffer as we might have changed it. + */ + if (data->flags & MMC_DATA_WRITE) { + dma_sync_single_for_device(mmc_dev(host->mmc), + host->align_addr, 128 * 4, direction); + } + + host->adma_addr = dma_map_single(mmc_dev(host->mmc), + host->adma_desc, (128 * 2 + 1) * 4, DMA_TO_DEVICE); + BUG_ON(host->adma_addr & 0x3); +} + +static void sdhci_adma_table_post(struct sdhci_host *host, + struct mmc_data *data) +{ + int direction; + + struct scatterlist *sg; + int i, size; + u8 *align; + char *buffer; + unsigned long flags; + + if (data->flags & MMC_DATA_READ) + direction = DMA_FROM_DEVICE; + else + direction = DMA_TO_DEVICE; + + dma_unmap_single(mmc_dev(host->mmc), host->adma_addr, + (128 * 2 + 1) * 4, DMA_TO_DEVICE); + + dma_unmap_single(mmc_dev(host->mmc), host->align_addr, + 128 * 4, direction); + + if (data->flags & MMC_DATA_READ) { + dma_sync_sg_for_cpu(mmc_dev(host->mmc), data->sg, + data->sg_len, direction); + + align = host->align_buffer; + + for_each_sg(data->sg, sg, host->sg_count, i) { + if (sg_dma_address(sg) & 0x3) { + size = 4 - (sg_dma_address(sg) & 0x3); + + buffer = sdhci_kmap_atomic(sg, &flags); + memcpy(buffer, align, size); + sdhci_kunmap_atomic(buffer, &flags); + + align += 4; + } + } + } + + dma_unmap_sg(mmc_dev(host->mmc), data->sg, + data->sg_len, direction); +} + static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data) { u8 count; @@ -363,6 +554,7 @@ static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_data *data) static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) { u8 count; + u8 ctrl; WARN_ON(host->data); @@ -383,35 +575,104 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) if (host->flags & SDHCI_USE_DMA) host->flags |= SDHCI_REQ_USE_DMA; - if (unlikely((host->flags & SDHCI_REQ_USE_DMA) && - (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE) && - ((data->blksz * data->blocks) & 0x3))) { - DBG("Reverting to PIO because of transfer size (%d)\n", - data->blksz * data->blocks); - host->flags &= ~SDHCI_REQ_USE_DMA; + /* + * FIXME: This doesn't account for merging when mapping the + * scatterlist. + */ + if (host->flags & SDHCI_REQ_USE_DMA) { + int broken, i; + struct scatterlist *sg; + + broken = 0; + if (host->flags & SDHCI_USE_ADMA) { + if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE) + broken = 1; + } else { + if (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE) + broken = 1; + } + + if (unlikely(broken)) { + for_each_sg(data->sg, sg, data->sg_len, i) { + if (sg->length & 0x3) { + DBG("Reverting to PIO because of " + "transfer size (%d)\n", + sg->length); + host->flags &= ~SDHCI_REQ_USE_DMA; + break; + } + } + } } /* * The assumption here being that alignment is the same after * translation to device address space. */ - if (unlikely((host->flags & SDHCI_REQ_USE_DMA) && - (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) && - (data->sg->offset & 0x3))) { - DBG("Reverting to PIO because of bad alignment\n"); - host->flags &= ~SDHCI_REQ_USE_DMA; + if (host->flags & SDHCI_REQ_USE_DMA) { + int broken, i; + struct scatterlist *sg; + + broken = 0; + if (host->flags & SDHCI_USE_ADMA) { + /* + * As we use 3 byte chunks to work around + * alignment problems, we need to check this + * quirk. + */ + if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE) + broken = 1; + } else { + if (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) + broken = 1; + } + + if (unlikely(broken)) { + for_each_sg(data->sg, sg, data->sg_len, i) { + if (sg->offset & 0x3) { + DBG("Reverting to PIO because of " + "bad alignment\n"); + host->flags &= ~SDHCI_REQ_USE_DMA; + break; + } + } + } + } + + /* + * Always adjust the DMA selection as some controllers + * (e.g. JMicron) can't do PIO properly when the selection + * is ADMA. + */ + if (host->version >= SDHCI_SPEC_200) { + ctrl = readb(host->ioaddr + SDHCI_HOST_CONTROL); + ctrl &= ~SDHCI_CTRL_DMA_MASK; + if ((host->flags & SDHCI_REQ_USE_DMA) && + (host->flags & SDHCI_USE_ADMA)) + ctrl |= SDHCI_CTRL_ADMA32; + else + ctrl |= SDHCI_CTRL_SDMA; + writeb(ctrl, host->ioaddr + SDHCI_HOST_CONTROL); } if (host->flags & SDHCI_REQ_USE_DMA) { - int count; + if (host->flags & SDHCI_USE_ADMA) { + sdhci_adma_table_pre(host, data); + writel(host->adma_addr, + host->ioaddr + SDHCI_ADMA_ADDRESS); + } else { + int count; - count = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len, - (data->flags & MMC_DATA_READ) ? - DMA_FROM_DEVICE : DMA_TO_DEVICE); - WARN_ON(count != 1); + count = dma_map_sg(mmc_dev(host->mmc), + data->sg, data->sg_len, + (data->flags & MMC_DATA_READ) ? + DMA_FROM_DEVICE : + DMA_TO_DEVICE); + WARN_ON(count != 1); - writel(sg_dma_address(data->sg), - host->ioaddr + SDHCI_DMA_ADDRESS); + writel(sg_dma_address(data->sg), + host->ioaddr + SDHCI_DMA_ADDRESS); + } } else { host->cur_sg = data->sg; host->num_sg = data->sg_len; @@ -457,9 +718,13 @@ static void sdhci_finish_data(struct sdhci_host *host) host->data = NULL; if (host->flags & SDHCI_REQ_USE_DMA) { - dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, - (data->flags & MMC_DATA_READ) ? - DMA_FROM_DEVICE : DMA_TO_DEVICE); + if (host->flags & SDHCI_USE_ADMA) + sdhci_adma_table_post(host, data); + else { + dma_unmap_sg(mmc_dev(host->mmc), data->sg, + data->sg_len, (data->flags & MMC_DATA_READ) ? + DMA_FROM_DEVICE : DMA_TO_DEVICE); + } } /* @@ -1008,6 +1273,8 @@ static void sdhci_data_irq(struct sdhci_host *host, u32 intmask) host->data->error = -ETIMEDOUT; else if (intmask & (SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_END_BIT)) host->data->error = -EILSEQ; + else if (intmask & SDHCI_INT_ADMA_ERROR) + host->data->error = -EIO; if (host->data->error) sdhci_finish_data(host); @@ -1199,7 +1466,6 @@ int sdhci_add_host(struct sdhci_host *host) { struct mmc_host *mmc; unsigned int caps; - unsigned int version; int ret; WARN_ON(host == NULL); @@ -1213,12 +1479,13 @@ int sdhci_add_host(struct sdhci_host *host) sdhci_reset(host, SDHCI_RESET_ALL); - version = readw(host->ioaddr + SDHCI_HOST_VERSION); - version = (version & SDHCI_SPEC_VER_MASK) >> SDHCI_SPEC_VER_SHIFT; - if (version > 1) { + host->version = readw(host->ioaddr + SDHCI_HOST_VERSION); + host->version = (host->version & SDHCI_SPEC_VER_MASK) + >> SDHCI_SPEC_VER_SHIFT; + if (host->version > SDHCI_SPEC_200) { printk(KERN_ERR "%s: Unknown controller version (%d). " "You may experience problems.\n", mmc_hostname(mmc), - version); + host->version); } caps = readl(host->ioaddr + SDHCI_CAPABILITIES); @@ -1237,16 +1504,46 @@ int sdhci_add_host(struct sdhci_host *host) } if (host->flags & SDHCI_USE_DMA) { + if ((host->version >= SDHCI_SPEC_200) && + (caps & SDHCI_CAN_DO_ADMA2)) + host->flags |= SDHCI_USE_ADMA; + } + + if ((host->quirks & SDHCI_QUIRK_BROKEN_ADMA) && + (host->flags & SDHCI_USE_ADMA)) { + DBG("Disabling ADMA as it is marked broken\n"); + host->flags &= ~SDHCI_USE_ADMA; + } + + if (host->flags & SDHCI_USE_DMA) { if (host->ops->enable_dma) { if (host->ops->enable_dma(host)) { printk(KERN_WARNING "%s: No suitable DMA " "available. Falling back to PIO.\n", mmc_hostname(mmc)); - host->flags &= ~SDHCI_USE_DMA; + host->flags &= ~(SDHCI_USE_DMA | SDHCI_USE_ADMA); } } } + if (host->flags & SDHCI_USE_ADMA) { + /* + * We need to allocate descriptors for all sg entries + * (128) and potentially one alignment transfer for + * each of those entries. + */ + host->adma_desc = kmalloc((128 * 2 + 1) * 4, GFP_KERNEL); + host->align_buffer = kmalloc(128 * 4, GFP_KERNEL); + if (!host->adma_desc || !host->align_buffer) { + kfree(host->adma_desc); + kfree(host->align_buffer); + printk(KERN_WARNING "%s: Unable to allocate ADMA " + "buffers. Falling back to standard DMA.\n", + mmc_hostname(mmc)); + host->flags &= ~SDHCI_USE_ADMA; + } + } + /* XXX: Hack to get MMC layer to avoid highmem */ if (!(host->flags & SDHCI_USE_DMA)) mmc_dev(host->mmc)->dma_mask = 0; @@ -1298,13 +1595,16 @@ int sdhci_add_host(struct sdhci_host *host) spin_lock_init(&host->lock); /* - * Maximum number of segments. Hardware cannot do scatter lists. + * Maximum number of segments. Depends on if the hardware + * can do scatter/gather or not. */ - if (host->flags & SDHCI_USE_DMA) + if (host->flags & SDHCI_USE_ADMA) + mmc->max_hw_segs = 128; + else if (host->flags & SDHCI_USE_DMA) mmc->max_hw_segs = 1; - else - mmc->max_hw_segs = 16; - mmc->max_phys_segs = 16; + else /* PIO */ + mmc->max_hw_segs = 128; + mmc->max_phys_segs = 128; /* * Maximum number of sectors in one transfer. Limited by DMA boundary @@ -1314,9 +1614,13 @@ int sdhci_add_host(struct sdhci_host *host) /* * Maximum segment size. Could be one segment with the maximum number - * of bytes. + * of bytes. When doing hardware scatter/gather, each entry cannot + * be larger than 64 KiB though. */ - mmc->max_seg_size = mmc->max_req_size; + if (host->flags & SDHCI_USE_ADMA) + mmc->max_seg_size = 65536; + else + mmc->max_seg_size = mmc->max_req_size; /* * Maximum block size. This varies from controller to controller and @@ -1371,8 +1675,9 @@ int sdhci_add_host(struct sdhci_host *host) mmc_add_host(mmc); - printk(KERN_INFO "%s: SDHCI controller on %s [%s] using %s\n", + printk(KERN_INFO "%s: SDHCI controller on %s [%s] using %s%s\n", mmc_hostname(mmc), host->hw_name, mmc_dev(mmc)->bus_id, + (host->flags & SDHCI_USE_ADMA)?"A":"", (host->flags & SDHCI_USE_DMA)?"DMA":"PIO"); return 0; @@ -1426,6 +1731,12 @@ void sdhci_remove_host(struct sdhci_host *host, int dead) tasklet_kill(&host->card_tasklet); tasklet_kill(&host->finish_tasklet); + + kfree(host->adma_desc); + kfree(host->align_buffer); + + host->adma_desc = NULL; + host->align_buffer = NULL; } EXPORT_SYMBOL_GPL(sdhci_remove_host); diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 7c30251..5bb3552 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -60,6 +60,11 @@ #define SDHCI_CTRL_LED 0x01 #define SDHCI_CTRL_4BITBUS 0x02 #define SDHCI_CTRL_HISPD 0x04 +#define SDHCI_CTRL_DMA_MASK 0x18 +#define SDHCI_CTRL_SDMA 0x00 +#define SDHCI_CTRL_ADMA1 0x08 +#define SDHCI_CTRL_ADMA32 0x10 +#define SDHCI_CTRL_ADMA64 0x18 #define SDHCI_POWER_CONTROL 0x29 #define SDHCI_POWER_ON 0x01 @@ -105,6 +110,7 @@ #define SDHCI_INT_DATA_END_BIT 0x00400000 #define SDHCI_INT_BUS_POWER 0x00800000 #define SDHCI_INT_ACMD12ERR 0x01000000 +#define SDHCI_INT_ADMA_ERROR 0x02000000 #define SDHCI_INT_NORMAL_MASK 0x00007FFF #define SDHCI_INT_ERROR_MASK 0xFFFF8000 @@ -128,11 +134,14 @@ #define SDHCI_CLOCK_BASE_SHIFT 8 #define SDHCI_MAX_BLOCK_MASK 0x00030000 #define SDHCI_MAX_BLOCK_SHIFT 16 +#define SDHCI_CAN_DO_ADMA2 0x00080000 +#define SDHCI_CAN_DO_ADMA1 0x00100000 #define SDHCI_CAN_DO_HISPD 0x00200000 #define SDHCI_CAN_DO_DMA 0x00400000 #define SDHCI_CAN_VDD_330 0x01000000 #define SDHCI_CAN_VDD_300 0x02000000 #define SDHCI_CAN_VDD_180 0x04000000 +#define SDHCI_CAN_64BIT 0x10000000 /* 44-47 reserved for more caps */ @@ -140,7 +149,16 @@ /* 4C-4F reserved for more max current */ -/* 50-FB reserved */ +#define SDHCI_SET_ACMD12_ERROR 0x50 +#define SDHCI_SET_INT_ERROR 0x52 + +#define SDHCI_ADMA_ERROR 0x54 + +/* 55-57 reserved */ + +#define SDHCI_ADMA_ADDRESS 0x58 + +/* 60-FB reserved */ #define SDHCI_SLOT_INT_STATUS 0xFC @@ -149,6 +167,8 @@ #define SDHCI_VENDOR_VER_SHIFT 8 #define SDHCI_SPEC_VER_MASK 0x00FF #define SDHCI_SPEC_VER_SHIFT 0 +#define SDHCI_SPEC_100 0 +#define SDHCI_SPEC_200 1 struct sdhci_ops; @@ -170,16 +190,20 @@ struct sdhci_host { #define SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS (1<<4) /* Controller has an unusable DMA engine */ #define SDHCI_QUIRK_BROKEN_DMA (1<<5) +/* Controller has an unusable ADMA engine */ +#define SDHCI_QUIRK_BROKEN_ADMA (1<<6) /* Controller can only DMA from 32-bit aligned addresses */ -#define SDHCI_QUIRK_32BIT_DMA_ADDR (1<<6) +#define SDHCI_QUIRK_32BIT_DMA_ADDR (1<<7) /* Controller can only DMA chunk sizes that are a multiple of 32 bits */ -#define SDHCI_QUIRK_32BIT_DMA_SIZE (1<<7) +#define SDHCI_QUIRK_32BIT_DMA_SIZE (1<<8) +/* Controller can only ADMA chunks that are a multiple of 32 bits */ +#define SDHCI_QUIRK_32BIT_ADMA_SIZE (1<<9) /* Controller needs to be reset after each request to stay stable */ -#define SDHCI_QUIRK_RESET_AFTER_REQUEST (1<<8) +#define SDHCI_QUIRK_RESET_AFTER_REQUEST (1<<10) /* Controller needs voltage and power writes to happen separately */ -#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<9) +#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1<<11) /* Controller provides an incorrect timeout value for transfers */ -#define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL (1<<10) +#define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL (1<<12) int irq; /* Device IRQ */ void __iomem * ioaddr; /* Mapped address */ @@ -197,8 +221,11 @@ struct sdhci_host { int flags; /* Host attributes */ #define SDHCI_USE_DMA (1<<0) /* Host is DMA capable */ -#define SDHCI_REQ_USE_DMA (1<<1) /* Use DMA for this req. */ -#define SDHCI_DEVICE_DEAD (1<<2) /* Device unresponsive */ +#define SDHCI_USE_ADMA (1<<1) /* Host is ADMA capable */ +#define SDHCI_REQ_USE_DMA (1<<2) /* Use DMA for this req. */ +#define SDHCI_DEVICE_DEAD (1<<3) /* Device unresponsive */ + + unsigned int version; /* SDHCI spec. version */ unsigned int max_clk; /* Max possible freq (MHz) */ unsigned int timeout_clk; /* Timeout freq (KHz) */ @@ -216,6 +243,14 @@ struct sdhci_host { int offset; /* Offset into current sg */ int remain; /* Bytes left in current */ + int sg_count; /* Mapped sg entries */ + + u8 *adma_desc; /* ADMA descriptor table */ + u8 *align_buffer; /* Bounce buffer */ + + dma_addr_t adma_addr; /* Mapped ADMA descr. table */ + dma_addr_t align_addr; /* Mapped bounce buffer */ + struct tasklet_struct card_tasklet; /* Tasklet structures */ struct tasklet_struct finish_tasklet; -- cgit v1.1 From 979ce7208a679b8d012450610d5d5aa75aab3af9 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sun, 29 Jun 2008 12:19:47 +0200 Subject: mmc_block: wait for card even on failures Many failures are non-permanent, but the card might need some time to finish what it is doing before becoming responsive again. Make sure we wait for it to finish programming before dealing with the error. Signed-off-by: Pierre Ossman --- drivers/mmc/card/block.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-) diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c index f9ad960..4b0f822 100644 --- a/drivers/mmc/card/block.c +++ b/drivers/mmc/card/block.c @@ -2,7 +2,7 @@ * Block driver for media (i.e., flash cards) * * Copyright 2002 Hewlett-Packard Company - * Copyright 2005-2007 Pierre Ossman + * Copyright 2005-2008 Pierre Ossman * * Use consistent with the GNU GPL is permitted, * provided that this copyright notice is @@ -296,22 +296,24 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req) mmc_queue_bounce_post(mq); + /* + * Check for errors here, but don't jump to cmd_err + * until later as we need to wait for the card to leave + * programming mode even when things go wrong. + */ if (brq.cmd.error) { printk(KERN_ERR "%s: error %d sending read/write command\n", req->rq_disk->disk_name, brq.cmd.error); - goto cmd_err; } if (brq.data.error) { printk(KERN_ERR "%s: error %d transferring data\n", req->rq_disk->disk_name, brq.data.error); - goto cmd_err; } if (brq.stop.error) { printk(KERN_ERR "%s: error %d sending stop command\n", req->rq_disk->disk_name, brq.stop.error); - goto cmd_err; } if (!mmc_host_is_spi(card->host) && rq_data_dir(req) != READ) { @@ -344,6 +346,9 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req) #endif } + if (brq.cmd.error || brq.data.error || brq.stop.error) + goto cmd_err; + /* * A block was successfully transferred. */ -- cgit v1.1 From 6b174931a73177c6519f87e6a8d5ae6ba269cdb5 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Mon, 30 Jun 2008 09:09:27 +0200 Subject: mmc_test: cleanup Clean up and reorganise the mmc_test driver so that it (hopefully) is easier to extend with more complex tests. Signed-off-by: Pierre Ossman --- drivers/mmc/card/mmc_test.c | 554 +++++++++++++++++++++++++++++--------------- 1 file changed, 364 insertions(+), 190 deletions(-) diff --git a/drivers/mmc/card/mmc_test.c b/drivers/mmc/card/mmc_test.c index 8e0bb12..d6b9b48 100644 --- a/drivers/mmc/card/mmc_test.c +++ b/drivers/mmc/card/mmc_test.c @@ -26,13 +26,17 @@ struct mmc_test_card { struct mmc_card *card; + u8 scratch[BUFFER_SIZE]; u8 *buffer; }; /*******************************************************************/ -/* Helper functions */ +/* General helper functions */ /*******************************************************************/ +/* + * Configure correct block size in card + */ static int mmc_test_set_blksize(struct mmc_test_card *test, unsigned size) { struct mmc_command cmd; @@ -48,117 +52,61 @@ static int mmc_test_set_blksize(struct mmc_test_card *test, unsigned size) return 0; } -static int __mmc_test_transfer(struct mmc_test_card *test, int write, - unsigned broken_xfer, u8 *buffer, unsigned addr, - unsigned blocks, unsigned blksz) +/* + * Fill in the mmc_request structure given a set of transfer parameters. + */ +static void mmc_test_prepare_mrq(struct mmc_test_card *test, + struct mmc_request *mrq, struct scatterlist *sg, unsigned sg_len, + unsigned dev_addr, unsigned blocks, unsigned blksz, int write) { - int ret, busy; + BUG_ON(!mrq || !mrq->cmd || !mrq->data || !mrq->stop); - struct mmc_request mrq; - struct mmc_command cmd; - struct mmc_command stop; - struct mmc_data data; - - struct scatterlist sg; - - memset(&mrq, 0, sizeof(struct mmc_request)); - - mrq.cmd = &cmd; - mrq.data = &data; - - memset(&cmd, 0, sizeof(struct mmc_command)); - - if (broken_xfer) { - if (blocks > 1) { - cmd.opcode = write ? - MMC_WRITE_BLOCK : MMC_READ_SINGLE_BLOCK; - } else { - cmd.opcode = MMC_SEND_STATUS; - } + if (blocks > 1) { + mrq->cmd->opcode = write ? + MMC_WRITE_MULTIPLE_BLOCK : MMC_READ_MULTIPLE_BLOCK; } else { - if (blocks > 1) { - cmd.opcode = write ? - MMC_WRITE_MULTIPLE_BLOCK : MMC_READ_MULTIPLE_BLOCK; - } else { - cmd.opcode = write ? - MMC_WRITE_BLOCK : MMC_READ_SINGLE_BLOCK; - } + mrq->cmd->opcode = write ? + MMC_WRITE_BLOCK : MMC_READ_SINGLE_BLOCK; } - if (broken_xfer && blocks == 1) - cmd.arg = test->card->rca << 16; - else - cmd.arg = addr; - cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC; - - memset(&stop, 0, sizeof(struct mmc_command)); - - if (!broken_xfer && (blocks > 1)) { - stop.opcode = MMC_STOP_TRANSMISSION; - stop.arg = 0; - stop.flags = MMC_RSP_R1B | MMC_CMD_AC; + mrq->cmd->arg = dev_addr; + mrq->cmd->flags = MMC_RSP_R1 | MMC_CMD_ADTC; - mrq.stop = &stop; + if (blocks == 1) + mrq->stop = NULL; + else { + mrq->stop->opcode = MMC_STOP_TRANSMISSION; + mrq->stop->arg = 0; + mrq->stop->flags = MMC_RSP_R1B | MMC_CMD_AC; } - memset(&data, 0, sizeof(struct mmc_data)); - - data.blksz = blksz; - data.blocks = blocks; - data.flags = write ? MMC_DATA_WRITE : MMC_DATA_READ; - data.sg = &sg; - data.sg_len = 1; - - sg_init_one(&sg, buffer, blocks * blksz); + mrq->data->blksz = blksz; + mrq->data->blocks = blocks; + mrq->data->flags = write ? MMC_DATA_WRITE : MMC_DATA_READ; + mrq->data->sg = sg; + mrq->data->sg_len = sg_len; - mmc_set_data_timeout(&data, test->card); - - mmc_wait_for_req(test->card->host, &mrq); - - ret = 0; - - if (broken_xfer) { - if (!ret && cmd.error) - ret = cmd.error; - if (!ret && data.error == 0) - ret = RESULT_FAIL; - if (!ret && data.error != -ETIMEDOUT) - ret = data.error; - if (!ret && stop.error) - ret = stop.error; - if (blocks > 1) { - if (!ret && data.bytes_xfered > blksz) - ret = RESULT_FAIL; - } else { - if (!ret && data.bytes_xfered > 0) - ret = RESULT_FAIL; - } - } else { - if (!ret && cmd.error) - ret = cmd.error; - if (!ret && data.error) - ret = data.error; - if (!ret && stop.error) - ret = stop.error; - if (!ret && data.bytes_xfered != blocks * blksz) - ret = RESULT_FAIL; - } + mmc_set_data_timeout(mrq->data, test->card); +} - if (ret == -EINVAL) - ret = RESULT_UNSUP_HOST; +/* + * Wait for the card to finish the busy state + */ +static int mmc_test_wait_busy(struct mmc_test_card *test) +{ + int ret, busy; + struct mmc_command cmd; busy = 0; do { - int ret2; - memset(&cmd, 0, sizeof(struct mmc_command)); cmd.opcode = MMC_SEND_STATUS; cmd.arg = test->card->rca << 16; cmd.flags = MMC_RSP_R1 | MMC_CMD_AC; - ret2 = mmc_wait_for_cmd(test->card->host, &cmd, 0); - if (ret2) + ret = mmc_wait_for_cmd(test->card->host, &cmd, 0); + if (ret) break; if (!busy && !(cmd.resp[0] & R1_READY_FOR_DATA)) { @@ -172,14 +120,57 @@ static int __mmc_test_transfer(struct mmc_test_card *test, int write, return ret; } -static int mmc_test_transfer(struct mmc_test_card *test, int write, - u8 *buffer, unsigned addr, unsigned blocks, unsigned blksz) +/* + * Transfer a single sector of kernel addressable data + */ +static int mmc_test_buffer_transfer(struct mmc_test_card *test, + u8 *buffer, unsigned addr, unsigned blksz, int write) { - return __mmc_test_transfer(test, write, 0, buffer, - addr, blocks, blksz); + int ret; + + struct mmc_request mrq; + struct mmc_command cmd; + struct mmc_command stop; + struct mmc_data data; + + struct scatterlist sg; + + memset(&mrq, 0, sizeof(struct mmc_request)); + memset(&cmd, 0, sizeof(struct mmc_command)); + memset(&data, 0, sizeof(struct mmc_data)); + memset(&stop, 0, sizeof(struct mmc_command)); + + mrq.cmd = &cmd; + mrq.data = &data; + mrq.stop = &stop; + + sg_init_one(&sg, buffer, blksz); + + mmc_test_prepare_mrq(test, &mrq, &sg, 1, addr, 1, blksz, write); + + mmc_wait_for_req(test->card->host, &mrq); + + if (cmd.error) + return cmd.error; + if (data.error) + return data.error; + + ret = mmc_test_wait_busy(test); + if (ret) + return ret; + + return 0; } -static int mmc_test_prepare_verify(struct mmc_test_card *test, int write) +/*******************************************************************/ +/* Test preparation and cleanup */ +/*******************************************************************/ + +/* + * Fill the first couple of sectors of the card with known data + * so that bad reads/writes can be detected + */ +static int __mmc_test_prepare(struct mmc_test_card *test, int write) { int ret, i; @@ -188,15 +179,14 @@ static int mmc_test_prepare_verify(struct mmc_test_card *test, int write) return ret; if (write) - memset(test->buffer, 0xDF, BUFFER_SIZE); + memset(test->buffer, 0xDF, 512); else { - for (i = 0;i < BUFFER_SIZE;i++) + for (i = 0;i < 512;i++) test->buffer[i] = i; } for (i = 0;i < BUFFER_SIZE / 512;i++) { - ret = mmc_test_transfer(test, 1, test->buffer + i * 512, - i * 512, 1, 512); + ret = mmc_test_buffer_transfer(test, test->buffer, i * 512, 512, 1); if (ret) return ret; } @@ -204,41 +194,218 @@ static int mmc_test_prepare_verify(struct mmc_test_card *test, int write) return 0; } -static int mmc_test_prepare_verify_write(struct mmc_test_card *test) +static int mmc_test_prepare_write(struct mmc_test_card *test) +{ + return __mmc_test_prepare(test, 1); +} + +static int mmc_test_prepare_read(struct mmc_test_card *test) +{ + return __mmc_test_prepare(test, 0); +} + +static int mmc_test_cleanup(struct mmc_test_card *test) +{ + int ret, i; + + ret = mmc_test_set_blksize(test, 512); + if (ret) + return ret; + + memset(test->buffer, 0, 512); + + for (i = 0;i < BUFFER_SIZE / 512;i++) { + ret = mmc_test_buffer_transfer(test, test->buffer, i * 512, 512, 1); + if (ret) + return ret; + } + + return 0; +} + +/*******************************************************************/ +/* Test execution helpers */ +/*******************************************************************/ + +/* + * Modifies the mmc_request to perform the "short transfer" tests + */ +static void mmc_test_prepare_broken_mrq(struct mmc_test_card *test, + struct mmc_request *mrq, int write) +{ + BUG_ON(!mrq || !mrq->cmd || !mrq->data); + + if (mrq->data->blocks > 1) { + mrq->cmd->opcode = write ? + MMC_WRITE_BLOCK : MMC_READ_SINGLE_BLOCK; + mrq->stop = NULL; + } else { + mrq->cmd->opcode = MMC_SEND_STATUS; + mrq->cmd->arg = test->card->rca << 16; + } +} + +/* + * Checks that a normal transfer didn't have any errors + */ +static int mmc_test_check_result(struct mmc_test_card *test, + struct mmc_request *mrq) { - return mmc_test_prepare_verify(test, 1); + int ret; + + BUG_ON(!mrq || !mrq->cmd || !mrq->data); + + ret = 0; + + if (!ret && mrq->cmd->error) + ret = mrq->cmd->error; + if (!ret && mrq->data->error) + ret = mrq->data->error; + if (!ret && mrq->stop && mrq->stop->error) + ret = mrq->stop->error; + if (!ret && mrq->data->bytes_xfered != + mrq->data->blocks * mrq->data->blksz) + ret = RESULT_FAIL; + + if (ret == -EINVAL) + ret = RESULT_UNSUP_HOST; + + return ret; } -static int mmc_test_prepare_verify_read(struct mmc_test_card *test) +/* + * Checks that a "short transfer" behaved as expected + */ +static int mmc_test_check_broken_result(struct mmc_test_card *test, + struct mmc_request *mrq) { - return mmc_test_prepare_verify(test, 0); + int ret; + + BUG_ON(!mrq || !mrq->cmd || !mrq->data); + + ret = 0; + + if (!ret && mrq->cmd->error) + ret = mrq->cmd->error; + if (!ret && mrq->data->error == 0) + ret = RESULT_FAIL; + if (!ret && mrq->data->error != -ETIMEDOUT) + ret = mrq->data->error; + if (!ret && mrq->stop && mrq->stop->error) + ret = mrq->stop->error; + if (mrq->data->blocks > 1) { + if (!ret && mrq->data->bytes_xfered > mrq->data->blksz) + ret = RESULT_FAIL; + } else { + if (!ret && mrq->data->bytes_xfered > 0) + ret = RESULT_FAIL; + } + + if (ret == -EINVAL) + ret = RESULT_UNSUP_HOST; + + return ret; } -static int mmc_test_verified_transfer(struct mmc_test_card *test, int write, - u8 *buffer, unsigned addr, unsigned blocks, unsigned blksz) +/* + * Tests a basic transfer with certain parameters + */ +static int mmc_test_simple_transfer(struct mmc_test_card *test, + struct scatterlist *sg, unsigned sg_len, unsigned dev_addr, + unsigned blocks, unsigned blksz, int write) { - int ret, i, sectors; + struct mmc_request mrq; + struct mmc_command cmd; + struct mmc_command stop; + struct mmc_data data; - /* - * It is assumed that the above preparation has been done. - */ + memset(&mrq, 0, sizeof(struct mmc_request)); + memset(&cmd, 0, sizeof(struct mmc_command)); + memset(&data, 0, sizeof(struct mmc_data)); + memset(&stop, 0, sizeof(struct mmc_command)); + + mrq.cmd = &cmd; + mrq.data = &data; + mrq.stop = &stop; + + mmc_test_prepare_mrq(test, &mrq, sg, sg_len, dev_addr, + blocks, blksz, write); + + mmc_wait_for_req(test->card->host, &mrq); - memset(test->buffer, 0, BUFFER_SIZE); + mmc_test_wait_busy(test); + + return mmc_test_check_result(test, &mrq); +} + +/* + * Tests a transfer where the card will fail completely or partly + */ +static int mmc_test_broken_transfer(struct mmc_test_card *test, + unsigned blocks, unsigned blksz, int write) +{ + struct mmc_request mrq; + struct mmc_command cmd; + struct mmc_command stop; + struct mmc_data data; + + struct scatterlist sg; + + memset(&mrq, 0, sizeof(struct mmc_request)); + memset(&cmd, 0, sizeof(struct mmc_command)); + memset(&data, 0, sizeof(struct mmc_data)); + memset(&stop, 0, sizeof(struct mmc_command)); + + mrq.cmd = &cmd; + mrq.data = &data; + mrq.stop = &stop; + + sg_init_one(&sg, test->buffer, blocks * blksz); + + mmc_test_prepare_mrq(test, &mrq, &sg, 1, 0, blocks, blksz, write); + mmc_test_prepare_broken_mrq(test, &mrq, write); + + mmc_wait_for_req(test->card->host, &mrq); + + mmc_test_wait_busy(test); + + return mmc_test_check_broken_result(test, &mrq); +} + +/* + * Does a complete transfer test where data is also validated + * + * Note: mmc_test_prepare() must have been done before this call + */ +static int mmc_test_transfer(struct mmc_test_card *test, + struct scatterlist *sg, unsigned sg_len, unsigned dev_addr, + unsigned blocks, unsigned blksz, int write) +{ + int ret, i; + unsigned long flags; if (write) { for (i = 0;i < blocks * blksz;i++) - buffer[i] = i; + test->scratch[i] = i; + } else { + memset(test->scratch, 0, BUFFER_SIZE); } + local_irq_save(flags); + sg_copy_from_buffer(sg, sg_len, test->scratch, BUFFER_SIZE); + local_irq_restore(flags); ret = mmc_test_set_blksize(test, blksz); if (ret) return ret; - ret = mmc_test_transfer(test, write, buffer, addr, blocks, blksz); + ret = mmc_test_simple_transfer(test, sg, sg_len, dev_addr, + blocks, blksz, write); if (ret) return ret; if (write) { + int sectors; + ret = mmc_test_set_blksize(test, 512); if (ret) return ret; @@ -253,9 +420,9 @@ static int mmc_test_verified_transfer(struct mmc_test_card *test, int write, memset(test->buffer, 0, sectors * 512); for (i = 0;i < sectors;i++) { - ret = mmc_test_transfer(test, 0, + ret = mmc_test_buffer_transfer(test, test->buffer + i * 512, - addr + i * 512, 1, 512); + dev_addr + i * 512, 512, 0); if (ret) return ret; } @@ -270,8 +437,11 @@ static int mmc_test_verified_transfer(struct mmc_test_card *test, int write, return RESULT_FAIL; } } else { + local_irq_save(flags); + sg_copy_to_buffer(sg, sg_len, test->scratch, BUFFER_SIZE); + local_irq_restore(flags); for (i = 0;i < blocks * blksz;i++) { - if (buffer[i] != (u8)i) + if (test->scratch[i] != (u8)i) return RESULT_FAIL; } } @@ -279,26 +449,6 @@ static int mmc_test_verified_transfer(struct mmc_test_card *test, int write, return 0; } -static int mmc_test_cleanup_verify(struct mmc_test_card *test) -{ - int ret, i; - - ret = mmc_test_set_blksize(test, 512); - if (ret) - return ret; - - memset(test->buffer, 0, BUFFER_SIZE); - - for (i = 0;i < BUFFER_SIZE / 512;i++) { - ret = mmc_test_transfer(test, 1, test->buffer + i * 512, - i * 512, 1, 512); - if (ret) - return ret; - } - - return 0; -} - /*******************************************************************/ /* Tests */ /*******************************************************************/ @@ -314,12 +464,15 @@ struct mmc_test_case { static int mmc_test_basic_write(struct mmc_test_card *test) { int ret; + struct scatterlist sg; ret = mmc_test_set_blksize(test, 512); if (ret) return ret; - ret = mmc_test_transfer(test, 1, test->buffer, 0, 1, 512); + sg_init_one(&sg, test->buffer, 512); + + ret = mmc_test_simple_transfer(test, &sg, 1, 0, 1, 512, 1); if (ret) return ret; @@ -329,12 +482,15 @@ static int mmc_test_basic_write(struct mmc_test_card *test) static int mmc_test_basic_read(struct mmc_test_card *test) { int ret; + struct scatterlist sg; ret = mmc_test_set_blksize(test, 512); if (ret) return ret; - ret = mmc_test_transfer(test, 0, test->buffer, 0, 1, 512); + sg_init_one(&sg, test->buffer, 512); + + ret = mmc_test_simple_transfer(test, &sg, 1, 0, 1, 512, 1); if (ret) return ret; @@ -344,8 +500,11 @@ static int mmc_test_basic_read(struct mmc_test_card *test) static int mmc_test_verify_write(struct mmc_test_card *test) { int ret; + struct scatterlist sg; + + sg_init_one(&sg, test->buffer, 512); - ret = mmc_test_verified_transfer(test, 1, test->buffer, 0, 1, 512); + ret = mmc_test_transfer(test, &sg, 1, 0, 1, 512, 1); if (ret) return ret; @@ -355,8 +514,11 @@ static int mmc_test_verify_write(struct mmc_test_card *test) static int mmc_test_verify_read(struct mmc_test_card *test) { int ret; + struct scatterlist sg; + + sg_init_one(&sg, test->buffer, 512); - ret = mmc_test_verified_transfer(test, 0, test->buffer, 0, 1, 512); + ret = mmc_test_transfer(test, &sg, 1, 0, 1, 512, 0); if (ret) return ret; @@ -367,6 +529,7 @@ static int mmc_test_multi_write(struct mmc_test_card *test) { int ret; unsigned int size; + struct scatterlist sg; if (test->card->host->max_blk_count == 1) return RESULT_UNSUP_HOST; @@ -379,8 +542,9 @@ static int mmc_test_multi_write(struct mmc_test_card *test) if (size < 1024) return RESULT_UNSUP_HOST; - ret = mmc_test_verified_transfer(test, 1, test->buffer, 0, - size / 512, 512); + sg_init_one(&sg, test->buffer, size); + + ret = mmc_test_transfer(test, &sg, 1, 0, size/512, 512, 1); if (ret) return ret; @@ -391,6 +555,7 @@ static int mmc_test_multi_read(struct mmc_test_card *test) { int ret; unsigned int size; + struct scatterlist sg; if (test->card->host->max_blk_count == 1) return RESULT_UNSUP_HOST; @@ -403,8 +568,9 @@ static int mmc_test_multi_read(struct mmc_test_card *test) if (size < 1024) return RESULT_UNSUP_HOST; - ret = mmc_test_verified_transfer(test, 0, test->buffer, 0, - size / 512, 512); + sg_init_one(&sg, test->buffer, size); + + ret = mmc_test_transfer(test, &sg, 1, 0, size/512, 512, 0); if (ret) return ret; @@ -414,13 +580,14 @@ static int mmc_test_multi_read(struct mmc_test_card *test) static int mmc_test_pow2_write(struct mmc_test_card *test) { int ret, i; + struct scatterlist sg; if (!test->card->csd.write_partial) return RESULT_UNSUP_CARD; for (i = 1; i < 512;i <<= 1) { - ret = mmc_test_verified_transfer(test, 1, - test->buffer, 0, 1, i); + sg_init_one(&sg, test->buffer, i); + ret = mmc_test_transfer(test, &sg, 1, 0, 1, i, 1); if (ret) return ret; } @@ -431,13 +598,14 @@ static int mmc_test_pow2_write(struct mmc_test_card *test) static int mmc_test_pow2_read(struct mmc_test_card *test) { int ret, i; + struct scatterlist sg; if (!test->card->csd.read_partial) return RESULT_UNSUP_CARD; for (i = 1; i < 512;i <<= 1) { - ret = mmc_test_verified_transfer(test, 0, - test->buffer, 0, 1, i); + sg_init_one(&sg, test->buffer, i); + ret = mmc_test_transfer(test, &sg, 1, 0, 1, i, 0); if (ret) return ret; } @@ -448,13 +616,14 @@ static int mmc_test_pow2_read(struct mmc_test_card *test) static int mmc_test_weird_write(struct mmc_test_card *test) { int ret, i; + struct scatterlist sg; if (!test->card->csd.write_partial) return RESULT_UNSUP_CARD; for (i = 3; i < 512;i += 7) { - ret = mmc_test_verified_transfer(test, 1, - test->buffer, 0, 1, i); + sg_init_one(&sg, test->buffer, i); + ret = mmc_test_transfer(test, &sg, 1, 0, 1, i, 1); if (ret) return ret; } @@ -465,13 +634,14 @@ static int mmc_test_weird_write(struct mmc_test_card *test) static int mmc_test_weird_read(struct mmc_test_card *test) { int ret, i; + struct scatterlist sg; if (!test->card->csd.read_partial) return RESULT_UNSUP_CARD; for (i = 3; i < 512;i += 7) { - ret = mmc_test_verified_transfer(test, 0, - test->buffer, 0, 1, i); + sg_init_one(&sg, test->buffer, i); + ret = mmc_test_transfer(test, &sg, 1, 0, 1, i, 0); if (ret) return ret; } @@ -482,10 +652,11 @@ static int mmc_test_weird_read(struct mmc_test_card *test) static int mmc_test_align_write(struct mmc_test_card *test) { int ret, i; + struct scatterlist sg; for (i = 1;i < 4;i++) { - ret = mmc_test_verified_transfer(test, 1, test->buffer + i, - 0, 1, 512); + sg_init_one(&sg, test->buffer + i, 512); + ret = mmc_test_transfer(test, &sg, 1, 0, 1, 512, 1); if (ret) return ret; } @@ -496,10 +667,11 @@ static int mmc_test_align_write(struct mmc_test_card *test) static int mmc_test_align_read(struct mmc_test_card *test) { int ret, i; + struct scatterlist sg; for (i = 1;i < 4;i++) { - ret = mmc_test_verified_transfer(test, 0, test->buffer + i, - 0, 1, 512); + sg_init_one(&sg, test->buffer + i, 512); + ret = mmc_test_transfer(test, &sg, 1, 0, 1, 512, 0); if (ret) return ret; } @@ -511,6 +683,7 @@ static int mmc_test_align_multi_write(struct mmc_test_card *test) { int ret, i; unsigned int size; + struct scatterlist sg; if (test->card->host->max_blk_count == 1) return RESULT_UNSUP_HOST; @@ -524,8 +697,8 @@ static int mmc_test_align_multi_write(struct mmc_test_card *test) return RESULT_UNSUP_HOST; for (i = 1;i < 4;i++) { - ret = mmc_test_verified_transfer(test, 1, test->buffer + i, - 0, size / 512, 512); + sg_init_one(&sg, test->buffer + i, size); + ret = mmc_test_transfer(test, &sg, 1, 0, size/512, 512, 1); if (ret) return ret; } @@ -537,6 +710,7 @@ static int mmc_test_align_multi_read(struct mmc_test_card *test) { int ret, i; unsigned int size; + struct scatterlist sg; if (test->card->host->max_blk_count == 1) return RESULT_UNSUP_HOST; @@ -550,8 +724,8 @@ static int mmc_test_align_multi_read(struct mmc_test_card *test) return RESULT_UNSUP_HOST; for (i = 1;i < 4;i++) { - ret = mmc_test_verified_transfer(test, 0, test->buffer + i, - 0, size / 512, 512); + sg_init_one(&sg, test->buffer + i, size); + ret = mmc_test_transfer(test, &sg, 1, 0, size/512, 512, 0); if (ret) return ret; } @@ -567,7 +741,7 @@ static int mmc_test_xfersize_write(struct mmc_test_card *test) if (ret) return ret; - ret = __mmc_test_transfer(test, 1, 1, test->buffer, 0, 1, 512); + ret = mmc_test_broken_transfer(test, 1, 512, 1); if (ret) return ret; @@ -582,7 +756,7 @@ static int mmc_test_xfersize_read(struct mmc_test_card *test) if (ret) return ret; - ret = __mmc_test_transfer(test, 0, 1, test->buffer, 0, 1, 512); + ret = mmc_test_broken_transfer(test, 1, 512, 0); if (ret) return ret; @@ -600,7 +774,7 @@ static int mmc_test_multi_xfersize_write(struct mmc_test_card *test) if (ret) return ret; - ret = __mmc_test_transfer(test, 1, 1, test->buffer, 0, 2, 512); + ret = mmc_test_broken_transfer(test, 2, 512, 1); if (ret) return ret; @@ -618,7 +792,7 @@ static int mmc_test_multi_xfersize_read(struct mmc_test_card *test) if (ret) return ret; - ret = __mmc_test_transfer(test, 0, 1, test->buffer, 0, 2, 512); + ret = mmc_test_broken_transfer(test, 2, 512, 0); if (ret) return ret; @@ -638,86 +812,86 @@ static const struct mmc_test_case mmc_test_cases[] = { { .name = "Basic write (with data verification)", - .prepare = mmc_test_prepare_verify_write, + .prepare = mmc_test_prepare_write, .run = mmc_test_verify_write, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Basic read (with data verification)", - .prepare = mmc_test_prepare_verify_read, + .prepare = mmc_test_prepare_read, .run = mmc_test_verify_read, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Multi-block write", - .prepare = mmc_test_prepare_verify_write, + .prepare = mmc_test_prepare_write, .run = mmc_test_multi_write, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Multi-block read", - .prepare = mmc_test_prepare_verify_read, + .prepare = mmc_test_prepare_read, .run = mmc_test_multi_read, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Power of two block writes", - .prepare = mmc_test_prepare_verify_write, + .prepare = mmc_test_prepare_write, .run = mmc_test_pow2_write, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Power of two block reads", - .prepare = mmc_test_prepare_verify_read, + .prepare = mmc_test_prepare_read, .run = mmc_test_pow2_read, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Weird sized block writes", - .prepare = mmc_test_prepare_verify_write, + .prepare = mmc_test_prepare_write, .run = mmc_test_weird_write, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Weird sized block reads", - .prepare = mmc_test_prepare_verify_read, + .prepare = mmc_test_prepare_read, .run = mmc_test_weird_read, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Badly aligned write", - .prepare = mmc_test_prepare_verify_write, + .prepare = mmc_test_prepare_write, .run = mmc_test_align_write, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Badly aligned read", - .prepare = mmc_test_prepare_verify_read, + .prepare = mmc_test_prepare_read, .run = mmc_test_align_read, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Badly aligned multi-block write", - .prepare = mmc_test_prepare_verify_write, + .prepare = mmc_test_prepare_write, .run = mmc_test_align_multi_write, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { .name = "Badly aligned multi-block read", - .prepare = mmc_test_prepare_verify_read, + .prepare = mmc_test_prepare_read, .run = mmc_test_align_multi_read, - .cleanup = mmc_test_cleanup_verify, + .cleanup = mmc_test_cleanup, }, { -- cgit v1.1 From 8f1934ce784bd8f2eaf06f190526500f7f3f9c74 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Mon, 30 Jun 2008 21:15:49 +0200 Subject: sdhci: graceful handling of bad addresses Be a bit more robust and fall back to PIO if someone is feeding us bogus addresses. Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci.c | 77 +++++++++++++++++++++++++++++++++++------------- 1 file changed, 57 insertions(+), 20 deletions(-) diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index b802044..d3e4a39 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -327,7 +327,7 @@ static void sdhci_kunmap_atomic(void *buffer, unsigned long *flags) local_irq_restore(*flags); } -static void sdhci_adma_table_pre(struct sdhci_host *host, +static int sdhci_adma_table_pre(struct sdhci_host *host, struct mmc_data *data) { int direction; @@ -360,10 +360,14 @@ static void sdhci_adma_table_pre(struct sdhci_host *host, host->align_addr = dma_map_single(mmc_dev(host->mmc), host->align_buffer, 128 * 4, direction); + if (dma_mapping_error(host->align_addr)) + goto fail; BUG_ON(host->align_addr & 0x3); host->sg_count = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len, direction); + if (host->sg_count == 0) + goto unmap_align; desc = host->adma_desc; align = host->align_buffer; @@ -457,7 +461,20 @@ static void sdhci_adma_table_pre(struct sdhci_host *host, host->adma_addr = dma_map_single(mmc_dev(host->mmc), host->adma_desc, (128 * 2 + 1) * 4, DMA_TO_DEVICE); + if (dma_mapping_error(host->align_addr)) + goto unmap_entries; BUG_ON(host->adma_addr & 0x3); + + return 0; + +unmap_entries: + dma_unmap_sg(mmc_dev(host->mmc), data->sg, + data->sg_len, direction); +unmap_align: + dma_unmap_single(mmc_dev(host->mmc), host->align_addr, + 128 * 4, direction); +fail: + return -EINVAL; } static void sdhci_adma_table_post(struct sdhci_host *host, @@ -555,6 +572,7 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) { u8 count; u8 ctrl; + int ret; WARN_ON(host->data); @@ -639,6 +657,43 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) } } + if (host->flags & SDHCI_REQ_USE_DMA) { + if (host->flags & SDHCI_USE_ADMA) { + ret = sdhci_adma_table_pre(host, data); + if (ret) { + /* + * This only happens when someone fed + * us an invalid request. + */ + WARN_ON(1); + host->flags &= ~SDHCI_USE_DMA; + } else { + writel(host->adma_addr, + host->ioaddr + SDHCI_ADMA_ADDRESS); + } + } else { + int count; + + count = dma_map_sg(mmc_dev(host->mmc), + data->sg, data->sg_len, + (data->flags & MMC_DATA_READ) ? + DMA_FROM_DEVICE : + DMA_TO_DEVICE); + if (count == 0) { + /* + * This only happens when someone fed + * us an invalid request. + */ + WARN_ON(1); + host->flags &= ~SDHCI_USE_DMA; + } else { + WARN_ON(count != 1); + writel(sg_dma_address(data->sg), + host->ioaddr + SDHCI_DMA_ADDRESS); + } + } + } + /* * Always adjust the DMA selection as some controllers * (e.g. JMicron) can't do PIO properly when the selection @@ -655,25 +710,7 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) writeb(ctrl, host->ioaddr + SDHCI_HOST_CONTROL); } - if (host->flags & SDHCI_REQ_USE_DMA) { - if (host->flags & SDHCI_USE_ADMA) { - sdhci_adma_table_pre(host, data); - writel(host->adma_addr, - host->ioaddr + SDHCI_ADMA_ADDRESS); - } else { - int count; - - count = dma_map_sg(mmc_dev(host->mmc), - data->sg, data->sg_len, - (data->flags & MMC_DATA_READ) ? - DMA_FROM_DEVICE : - DMA_TO_DEVICE); - WARN_ON(count != 1); - - writel(sg_dma_address(data->sg), - host->ioaddr + SDHCI_DMA_ADDRESS); - } - } else { + if (!(host->flags & SDHCI_REQ_USE_DMA)) { host->cur_sg = data->sg; host->num_sg = data->sg_len; -- cgit v1.1 From be518018c6b9224c02284fb243207ef741c31ec6 Mon Sep 17 00:00:00 2001 From: Thomas Kleffel Date: Mon, 30 Jun 2008 22:40:24 +0100 Subject: MMC: S3C24XX MMC/SD driver. This is the latest S3C MMC/SD driver by Thomas Kleffel with cleanups as suggested by AKPM done by Ben Dooks. Signed-off-by: Ben Dooks Signed-off-by: Thomas Kleffel Signed-off-by: Pierre Ossman --- drivers/mmc/host/Kconfig | 11 + drivers/mmc/host/Makefile | 2 +- drivers/mmc/host/s3cmci.c | 1343 +++++++++++++++++++++++++++++++ drivers/mmc/host/s3cmci.h | 69 ++ include/asm-arm/arch-s3c2410/regs-sdi.h | 20 +- 5 files changed, 1441 insertions(+), 4 deletions(-) create mode 100644 drivers/mmc/host/s3cmci.c create mode 100644 drivers/mmc/host/s3cmci.h diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index f9cbcb8..dc88c03 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -143,3 +143,14 @@ config MMC_SPI If unsure, or if your system has no SPI master driver, say N. +config MMC_S3C + tristate "Samsung S3C SD/MMC Card Interface support" + depends on ARCH_S3C2410 && MMC + help + This selects a driver for the MCI interface found in + Samsung's S3C2410, S3C2412, S3C2440, S3C2442 CPUs. + If you have a board based on one of those and a MMC/SD + slot, say Y or M here. + + If unsure, say N. + diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index 3027250..b3e023b 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -18,4 +18,4 @@ obj-$(CONFIG_MMC_OMAP) += omap.o obj-$(CONFIG_MMC_AT91) += at91_mci.o obj-$(CONFIG_MMC_TIFM_SD) += tifm_sd.o obj-$(CONFIG_MMC_SPI) += mmc_spi.o - +obj-$(CONFIG_MMC_S3C) += s3cmci.o diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c new file mode 100644 index 0000000..c6a4d3c --- /dev/null +++ b/drivers/mmc/host/s3cmci.c @@ -0,0 +1,1343 @@ +/* + * linux/drivers/mmc/s3cmci.h - Samsung S3C MCI driver + * + * Copyright (C) 2004-2006 maintech GmbH, Thomas Kleffel + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include + +#include "s3cmci.h" + +#define DRIVER_NAME "s3c-mci" + +enum dbg_channels { + dbg_err = (1 << 0), + dbg_debug = (1 << 1), + dbg_info = (1 << 2), + dbg_irq = (1 << 3), + dbg_sg = (1 << 4), + dbg_dma = (1 << 5), + dbg_pio = (1 << 6), + dbg_fail = (1 << 7), + dbg_conf = (1 << 8), +}; + +static const int dbgmap_err = dbg_err | dbg_fail; +static const int dbgmap_info = dbg_info | dbg_conf; +static const int dbgmap_debug = dbg_debug; + +#define dbg(host, channels, args...) \ + do { \ + if (dbgmap_err & channels) \ + dev_err(&host->pdev->dev, args); \ + else if (dbgmap_info & channels) \ + dev_info(&host->pdev->dev, args); \ + else if (dbgmap_debug & channels) \ + dev_dbg(&host->pdev->dev, args); \ + } while (0) + +#define RESSIZE(ressource) (((ressource)->end - (ressource)->start)+1) + +static struct s3c2410_dma_client s3cmci_dma_client = { + .name = "s3c-mci", +}; + +static void finalize_request(struct s3cmci_host *host); +static void s3cmci_send_request(struct mmc_host *mmc); +static void s3cmci_reset(struct s3cmci_host *host); + +#ifdef CONFIG_MMC_DEBUG + +static void dbg_dumpregs(struct s3cmci_host *host, char *prefix) +{ + u32 con, pre, cmdarg, cmdcon, cmdsta, r0, r1, r2, r3, timer, bsize; + u32 datcon, datcnt, datsta, fsta, imask; + + con = readl(host->base + S3C2410_SDICON); + pre = readl(host->base + S3C2410_SDIPRE); + cmdarg = readl(host->base + S3C2410_SDICMDARG); + cmdcon = readl(host->base + S3C2410_SDICMDCON); + cmdsta = readl(host->base + S3C2410_SDICMDSTAT); + r0 = readl(host->base + S3C2410_SDIRSP0); + r1 = readl(host->base + S3C2410_SDIRSP1); + r2 = readl(host->base + S3C2410_SDIRSP2); + r3 = readl(host->base + S3C2410_SDIRSP3); + timer = readl(host->base + S3C2410_SDITIMER); + bsize = readl(host->base + S3C2410_SDIBSIZE); + datcon = readl(host->base + S3C2410_SDIDCON); + datcnt = readl(host->base + S3C2410_SDIDCNT); + datsta = readl(host->base + S3C2410_SDIDSTA); + fsta = readl(host->base + S3C2410_SDIFSTA); + imask = readl(host->base + host->sdiimsk); + + dbg(host, dbg_debug, "%s CON:[%08x] PRE:[%08x] TMR:[%08x]\n", + prefix, con, pre, timer); + + dbg(host, dbg_debug, "%s CCON:[%08x] CARG:[%08x] CSTA:[%08x]\n", + prefix, cmdcon, cmdarg, cmdsta); + + dbg(host, dbg_debug, "%s DCON:[%08x] FSTA:[%08x]" + " DSTA:[%08x] DCNT:[%08x]\n", + prefix, datcon, fsta, datsta, datcnt); + + dbg(host, dbg_debug, "%s R0:[%08x] R1:[%08x]" + " R2:[%08x] R3:[%08x]\n", + prefix, r0, r1, r2, r3); +} + +static void prepare_dbgmsg(struct s3cmci_host *host, struct mmc_command *cmd, + int stop) +{ + snprintf(host->dbgmsg_cmd, 300, + "#%u%s op:%i arg:0x%08x flags:0x08%x retries:%u", + host->ccnt, (stop ? " (STOP)" : ""), + cmd->opcode, cmd->arg, cmd->flags, cmd->retries); + + if (cmd->data) { + snprintf(host->dbgmsg_dat, 300, + "#%u bsize:%u blocks:%u bytes:%u", + host->dcnt, cmd->data->blksz, + cmd->data->blocks, + cmd->data->blocks * cmd->data->blksz); + } else { + host->dbgmsg_dat[0] = '\0'; + } +} + +static void dbg_dumpcmd(struct s3cmci_host *host, struct mmc_command *cmd, + int fail) +{ + unsigned int dbglvl = fail ? dbg_fail : dbg_debug; + + if (!cmd) + return; + + if (cmd->error == 0) { + dbg(host, dbglvl, "CMD[OK] %s R0:0x%08x\n", + host->dbgmsg_cmd, cmd->resp[0]); + } else { + dbg(host, dbglvl, "CMD[ERR %i] %s Status:%s\n", + cmd->error, host->dbgmsg_cmd, host->status); + } + + if (!cmd->data) + return; + + if (cmd->data->error == 0) { + dbg(host, dbglvl, "DAT[OK] %s\n", host->dbgmsg_dat); + } else { + dbg(host, dbglvl, "DAT[ERR %i] %s DCNT:0x%08x\n", + cmd->data->error, host->dbgmsg_dat, + readl(host->base + S3C2410_SDIDCNT)); + } +} +#else +static void dbg_dumpcmd(struct s3cmci_host *host, + struct mmc_command *cmd, int fail) { } + +static void prepare_dbgmsg(struct s3cmci_host *host, struct mmc_command *cmd, + int stop) { } + +static void dbg_dumpregs(struct s3cmci_host *host, char *prefix) { } + +#endif /* CONFIG_MMC_DEBUG */ + +static inline u32 enable_imask(struct s3cmci_host *host, u32 imask) +{ + u32 newmask; + + newmask = readl(host->base + host->sdiimsk); + newmask |= imask; + + writel(newmask, host->base + host->sdiimsk); + + return newmask; +} + +static inline u32 disable_imask(struct s3cmci_host *host, u32 imask) +{ + u32 newmask; + + newmask = readl(host->base + host->sdiimsk); + newmask &= ~imask; + + writel(newmask, host->base + host->sdiimsk); + + return newmask; +} + +static inline void clear_imask(struct s3cmci_host *host) +{ + writel(0, host->base + host->sdiimsk); +} + +static inline int get_data_buffer(struct s3cmci_host *host, + u32 *words, u32 **pointer) +{ + struct scatterlist *sg; + + if (host->pio_active == XFER_NONE) + return -EINVAL; + + if ((!host->mrq) || (!host->mrq->data)) + return -EINVAL; + + if (host->pio_sgptr >= host->mrq->data->sg_len) { + dbg(host, dbg_debug, "no more buffers (%i/%i)\n", + host->pio_sgptr, host->mrq->data->sg_len); + return -EBUSY; + } + sg = &host->mrq->data->sg[host->pio_sgptr]; + + *words = sg->length >> 2; + *pointer = sg_virt(sg); + + host->pio_sgptr++; + + dbg(host, dbg_sg, "new buffer (%i/%i)\n", + host->pio_sgptr, host->mrq->data->sg_len); + + return 0; +} + +static inline u32 fifo_count(struct s3cmci_host *host) +{ + u32 fifostat = readl(host->base + S3C2410_SDIFSTA); + + fifostat &= S3C2410_SDIFSTA_COUNTMASK; + return fifostat >> 2; +} + +static inline u32 fifo_free(struct s3cmci_host *host) +{ + u32 fifostat = readl(host->base + S3C2410_SDIFSTA); + + fifostat &= S3C2410_SDIFSTA_COUNTMASK; + return (63 - fifostat) >> 2; +} + +static void do_pio_read(struct s3cmci_host *host) +{ + int res; + u32 fifo; + void __iomem *from_ptr; + + /* write real prescaler to host, it might be set slow to fix */ + writel(host->prescaler, host->base + S3C2410_SDIPRE); + + from_ptr = host->base + host->sdidata; + + while ((fifo = fifo_count(host))) { + if (!host->pio_words) { + res = get_data_buffer(host, &host->pio_words, + &host->pio_ptr); + if (res) { + host->pio_active = XFER_NONE; + host->complete_what = COMPLETION_FINALIZE; + + dbg(host, dbg_pio, "pio_read(): " + "complete (no more data).\n"); + return; + } + + dbg(host, dbg_pio, + "pio_read(): new target: [%i]@[%p]\n", + host->pio_words, host->pio_ptr); + } + + dbg(host, dbg_pio, + "pio_read(): fifo:[%02i] buffer:[%03i] dcnt:[%08X]\n", + fifo, host->pio_words, + readl(host->base + S3C2410_SDIDCNT)); + + if (fifo > host->pio_words) + fifo = host->pio_words; + + host->pio_words -= fifo; + host->pio_count += fifo; + + while (fifo--) + *(host->pio_ptr++) = readl(from_ptr); + } + + if (!host->pio_words) { + res = get_data_buffer(host, &host->pio_words, &host->pio_ptr); + if (res) { + dbg(host, dbg_pio, + "pio_read(): complete (no more buffers).\n"); + host->pio_active = XFER_NONE; + host->complete_what = COMPLETION_FINALIZE; + + return; + } + } + + enable_imask(host, + S3C2410_SDIIMSK_RXFIFOHALF | S3C2410_SDIIMSK_RXFIFOLAST); +} + +static void do_pio_write(struct s3cmci_host *host) +{ + void __iomem *to_ptr; + int res; + u32 fifo; + + to_ptr = host->base + host->sdidata; + + while ((fifo = fifo_free(host))) { + if (!host->pio_words) { + res = get_data_buffer(host, &host->pio_words, + &host->pio_ptr); + if (res) { + dbg(host, dbg_pio, + "pio_write(): complete (no more data).\n"); + host->pio_active = XFER_NONE; + + return; + } + + dbg(host, dbg_pio, + "pio_write(): new source: [%i]@[%p]\n", + host->pio_words, host->pio_ptr); + + } + + if (fifo > host->pio_words) + fifo = host->pio_words; + + host->pio_words -= fifo; + host->pio_count += fifo; + + while (fifo--) + writel(*(host->pio_ptr++), to_ptr); + } + + enable_imask(host, S3C2410_SDIIMSK_TXFIFOHALF); +} + +static void pio_tasklet(unsigned long data) +{ + struct s3cmci_host *host = (struct s3cmci_host *) data; + + + if (host->pio_active == XFER_WRITE) + do_pio_write(host); + + if (host->pio_active == XFER_READ) + do_pio_read(host); + + if (host->complete_what == COMPLETION_FINALIZE) { + clear_imask(host); + if (host->pio_active != XFER_NONE) { + dbg(host, dbg_err, "unfinished %s " + "- pio_count:[%u] pio_words:[%u]\n", + (host->pio_active == XFER_READ) ? "read" : "write", + host->pio_count, host->pio_words); + + host->mrq->data->error = -EINVAL; + } + + disable_irq(host->irq); + finalize_request(host); + } +} + +/* + * ISR for SDI Interface IRQ + * Communication between driver and ISR works as follows: + * host->mrq points to current request + * host->complete_what Indicates when the request is considered done + * COMPLETION_CMDSENT when the command was sent + * COMPLETION_RSPFIN when a response was received + * COMPLETION_XFERFINISH when the data transfer is finished + * COMPLETION_XFERFINISH_RSPFIN both of the above. + * host->complete_request is the completion-object the driver waits for + * + * 1) Driver sets up host->mrq and host->complete_what + * 2) Driver prepares the transfer + * 3) Driver enables interrupts + * 4) Driver starts transfer + * 5) Driver waits for host->complete_rquest + * 6) ISR checks for request status (errors and success) + * 6) ISR sets host->mrq->cmd->error and host->mrq->data->error + * 7) ISR completes host->complete_request + * 8) ISR disables interrupts + * 9) Driver wakes up and takes care of the request + * + * Note: "->error"-fields are expected to be set to 0 before the request + * was issued by mmc.c - therefore they are only set, when an error + * contition comes up + */ + +static irqreturn_t s3cmci_irq(int irq, void *dev_id) +{ + struct s3cmci_host *host = dev_id; + struct mmc_command *cmd; + u32 mci_csta, mci_dsta, mci_fsta, mci_dcnt, mci_imsk; + u32 mci_cclear, mci_dclear; + unsigned long iflags; + + spin_lock_irqsave(&host->complete_lock, iflags); + + mci_csta = readl(host->base + S3C2410_SDICMDSTAT); + mci_dsta = readl(host->base + S3C2410_SDIDSTA); + mci_dcnt = readl(host->base + S3C2410_SDIDCNT); + mci_fsta = readl(host->base + S3C2410_SDIFSTA); + mci_imsk = readl(host->base + host->sdiimsk); + mci_cclear = 0; + mci_dclear = 0; + + if ((host->complete_what == COMPLETION_NONE) || + (host->complete_what == COMPLETION_FINALIZE)) { + host->status = "nothing to complete"; + clear_imask(host); + goto irq_out; + } + + if (!host->mrq) { + host->status = "no active mrq"; + clear_imask(host); + goto irq_out; + } + + cmd = host->cmd_is_stop ? host->mrq->stop : host->mrq->cmd; + + if (!cmd) { + host->status = "no active cmd"; + clear_imask(host); + goto irq_out; + } + + if (!host->dodma) { + if ((host->pio_active == XFER_WRITE) && + (mci_fsta & S3C2410_SDIFSTA_TFDET)) { + + disable_imask(host, S3C2410_SDIIMSK_TXFIFOHALF); + tasklet_schedule(&host->pio_tasklet); + host->status = "pio tx"; + } + + if ((host->pio_active == XFER_READ) && + (mci_fsta & S3C2410_SDIFSTA_RFDET)) { + + disable_imask(host, + S3C2410_SDIIMSK_RXFIFOHALF | + S3C2410_SDIIMSK_RXFIFOLAST); + + tasklet_schedule(&host->pio_tasklet); + host->status = "pio rx"; + } + } + + if (mci_csta & S3C2410_SDICMDSTAT_CMDTIMEOUT) { + cmd->error = -ETIMEDOUT; + host->status = "error: command timeout"; + goto fail_transfer; + } + + if (mci_csta & S3C2410_SDICMDSTAT_CMDSENT) { + if (host->complete_what == COMPLETION_CMDSENT) { + host->status = "ok: command sent"; + goto close_transfer; + } + + mci_cclear |= S3C2410_SDICMDSTAT_CMDSENT; + } + + if (mci_csta & S3C2410_SDICMDSTAT_CRCFAIL) { + if (cmd->flags & MMC_RSP_CRC) { + cmd->error = -EILSEQ; + host->status = "error: bad command crc"; + goto fail_transfer; + } + + mci_cclear |= S3C2410_SDICMDSTAT_CRCFAIL; + } + + if (mci_csta & S3C2410_SDICMDSTAT_RSPFIN) { + if (host->complete_what == COMPLETION_RSPFIN) { + host->status = "ok: command response received"; + goto close_transfer; + } + + if (host->complete_what == COMPLETION_XFERFINISH_RSPFIN) + host->complete_what = COMPLETION_XFERFINISH; + + mci_cclear |= S3C2410_SDICMDSTAT_RSPFIN; + } + + /* errors handled after this point are only relevant + when a data transfer is in progress */ + + if (!cmd->data) + goto clear_status_bits; + + /* Check for FIFO failure */ + if (host->is2440) { + if (mci_fsta & S3C2440_SDIFSTA_FIFOFAIL) { + host->mrq->data->error = -EILSEQ; + host->status = "error: 2440 fifo failure"; + goto fail_transfer; + } + } else { + if (mci_dsta & S3C2410_SDIDSTA_FIFOFAIL) { + cmd->data->error = -EILSEQ; + host->status = "error: fifo failure"; + goto fail_transfer; + } + } + + if (mci_dsta & S3C2410_SDIDSTA_RXCRCFAIL) { + cmd->data->error = -EILSEQ; + host->status = "error: bad data crc (outgoing)"; + goto fail_transfer; + } + + if (mci_dsta & S3C2410_SDIDSTA_CRCFAIL) { + cmd->data->error = -EILSEQ; + host->status = "error: bad data crc (incoming)"; + goto fail_transfer; + } + + if (mci_dsta & S3C2410_SDIDSTA_DATATIMEOUT) { + cmd->data->error = -ETIMEDOUT; + host->status = "error: data timeout"; + goto fail_transfer; + } + + if (mci_dsta & S3C2410_SDIDSTA_XFERFINISH) { + if (host->complete_what == COMPLETION_XFERFINISH) { + host->status = "ok: data transfer completed"; + goto close_transfer; + } + + if (host->complete_what == COMPLETION_XFERFINISH_RSPFIN) + host->complete_what = COMPLETION_RSPFIN; + + mci_dclear |= S3C2410_SDIDSTA_XFERFINISH; + } + +clear_status_bits: + writel(mci_cclear, host->base + S3C2410_SDICMDSTAT); + writel(mci_dclear, host->base + S3C2410_SDIDSTA); + + goto irq_out; + +fail_transfer: + host->pio_active = XFER_NONE; + +close_transfer: + host->complete_what = COMPLETION_FINALIZE; + + clear_imask(host); + tasklet_schedule(&host->pio_tasklet); + + goto irq_out; + +irq_out: + dbg(host, dbg_irq, + "csta:0x%08x dsta:0x%08x fsta:0x%08x dcnt:0x%08x status:%s.\n", + mci_csta, mci_dsta, mci_fsta, mci_dcnt, host->status); + + spin_unlock_irqrestore(&host->complete_lock, iflags); + return IRQ_HANDLED; + +} + +/* + * ISR for the CardDetect Pin +*/ + +static irqreturn_t s3cmci_irq_cd(int irq, void *dev_id) +{ + struct s3cmci_host *host = (struct s3cmci_host *)dev_id; + + dbg(host, dbg_irq, "card detect\n"); + + mmc_detect_change(host->mmc, 500); + + return IRQ_HANDLED; +} + +void s3cmci_dma_done_callback(struct s3c2410_dma_chan *dma_ch, void *buf_id, + int size, enum s3c2410_dma_buffresult result) +{ + struct s3cmci_host *host = buf_id; + unsigned long iflags; + u32 mci_csta, mci_dsta, mci_fsta, mci_dcnt; + + mci_csta = readl(host->base + S3C2410_SDICMDSTAT); + mci_dsta = readl(host->base + S3C2410_SDIDSTA); + mci_fsta = readl(host->base + S3C2410_SDIFSTA); + mci_dcnt = readl(host->base + S3C2410_SDIDCNT); + + BUG_ON(!host->mrq); + BUG_ON(!host->mrq->data); + BUG_ON(!host->dmatogo); + + spin_lock_irqsave(&host->complete_lock, iflags); + + if (result != S3C2410_RES_OK) { + dbg(host, dbg_fail, "DMA FAILED: csta=0x%08x dsta=0x%08x " + "fsta=0x%08x dcnt:0x%08x result:0x%08x toGo:%u\n", + mci_csta, mci_dsta, mci_fsta, + mci_dcnt, result, host->dmatogo); + + goto fail_request; + } + + host->dmatogo--; + if (host->dmatogo) { + dbg(host, dbg_dma, "DMA DONE Size:%i DSTA:[%08x] " + "DCNT:[%08x] toGo:%u\n", + size, mci_dsta, mci_dcnt, host->dmatogo); + + goto out; + } + + dbg(host, dbg_dma, "DMA FINISHED Size:%i DSTA:%08x DCNT:%08x\n", + size, mci_dsta, mci_dcnt); + + host->complete_what = COMPLETION_FINALIZE; + +out: + tasklet_schedule(&host->pio_tasklet); + spin_unlock_irqrestore(&host->complete_lock, iflags); + return; + + +fail_request: + host->mrq->data->error = -EINVAL; + host->complete_what = COMPLETION_FINALIZE; + writel(0, host->base + host->sdiimsk); + goto out; + +} + +static void finalize_request(struct s3cmci_host *host) +{ + struct mmc_request *mrq = host->mrq; + struct mmc_command *cmd = host->cmd_is_stop ? mrq->stop : mrq->cmd; + int debug_as_failure = 0; + + if (host->complete_what != COMPLETION_FINALIZE) + return; + + if (!mrq) + return; + + if (cmd->data && (cmd->error == 0) && + (cmd->data->error == 0)) { + if (host->dodma && (!host->dma_complete)) { + dbg(host, dbg_dma, "DMA Missing!\n"); + return; + } + } + + /* Read response from controller. */ + cmd->resp[0] = readl(host->base + S3C2410_SDIRSP0); + cmd->resp[1] = readl(host->base + S3C2410_SDIRSP1); + cmd->resp[2] = readl(host->base + S3C2410_SDIRSP2); + cmd->resp[3] = readl(host->base + S3C2410_SDIRSP3); + + writel(host->prescaler, host->base + S3C2410_SDIPRE); + + if (cmd->error) + debug_as_failure = 1; + + if (cmd->data && cmd->data->error) + debug_as_failure = 1; + + dbg_dumpcmd(host, cmd, debug_as_failure); + + /* Cleanup controller */ + writel(0, host->base + S3C2410_SDICMDARG); + writel(0, host->base + S3C2410_SDIDCON); + writel(0, host->base + S3C2410_SDICMDCON); + writel(0, host->base + host->sdiimsk); + + if (cmd->data && cmd->error) + cmd->data->error = cmd->error; + + if (cmd->data && cmd->data->stop && (!host->cmd_is_stop)) { + host->cmd_is_stop = 1; + s3cmci_send_request(host->mmc); + return; + } + + /* If we have no data transfer we are finished here */ + if (!mrq->data) + goto request_done; + + /* Calulate the amout of bytes transfer if there was no error */ + if (mrq->data->error == 0) { + mrq->data->bytes_xfered = + (mrq->data->blocks * mrq->data->blksz); + } else { + mrq->data->bytes_xfered = 0; + } + + /* If we had an error while transfering data we flush the + * DMA channel and the fifo to clear out any garbage. */ + if (mrq->data->error != 0) { + if (host->dodma) + s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_FLUSH); + + if (host->is2440) { + /* Clear failure register and reset fifo. */ + writel(S3C2440_SDIFSTA_FIFORESET | + S3C2440_SDIFSTA_FIFOFAIL, + host->base + S3C2410_SDIFSTA); + } else { + u32 mci_con; + + /* reset fifo */ + mci_con = readl(host->base + S3C2410_SDICON); + mci_con |= S3C2410_SDICON_FIFORESET; + + writel(mci_con, host->base + S3C2410_SDICON); + } + } + +request_done: + host->complete_what = COMPLETION_NONE; + host->mrq = NULL; + mmc_request_done(host->mmc, mrq); +} + + +void s3cmci_dma_setup(struct s3cmci_host *host, enum s3c2410_dmasrc source) +{ + static enum s3c2410_dmasrc last_source = -1; + static int setup_ok; + + if (last_source == source) + return; + + last_source = source; + + s3c2410_dma_devconfig(host->dma, source, 3, + host->mem->start + host->sdidata); + + if (!setup_ok) { + s3c2410_dma_config(host->dma, 4, + (S3C2410_DCON_HWTRIG | S3C2410_DCON_CH0_SDI)); + s3c2410_dma_set_buffdone_fn(host->dma, + s3cmci_dma_done_callback); + s3c2410_dma_setflags(host->dma, S3C2410_DMAF_AUTOSTART); + setup_ok = 1; + } +} + +static void s3cmci_send_command(struct s3cmci_host *host, + struct mmc_command *cmd) +{ + u32 ccon, imsk; + + imsk = S3C2410_SDIIMSK_CRCSTATUS | S3C2410_SDIIMSK_CMDTIMEOUT | + S3C2410_SDIIMSK_RESPONSEND | S3C2410_SDIIMSK_CMDSENT | + S3C2410_SDIIMSK_RESPONSECRC; + + enable_imask(host, imsk); + + if (cmd->data) + host->complete_what = COMPLETION_XFERFINISH_RSPFIN; + else if (cmd->flags & MMC_RSP_PRESENT) + host->complete_what = COMPLETION_RSPFIN; + else + host->complete_what = COMPLETION_CMDSENT; + + writel(cmd->arg, host->base + S3C2410_SDICMDARG); + + ccon = cmd->opcode & S3C2410_SDICMDCON_INDEX; + ccon |= S3C2410_SDICMDCON_SENDERHOST | S3C2410_SDICMDCON_CMDSTART; + + if (cmd->flags & MMC_RSP_PRESENT) + ccon |= S3C2410_SDICMDCON_WAITRSP; + + if (cmd->flags & MMC_RSP_136) + ccon |= S3C2410_SDICMDCON_LONGRSP; + + writel(ccon, host->base + S3C2410_SDICMDCON); +} + +static int s3cmci_setup_data(struct s3cmci_host *host, struct mmc_data *data) +{ + u32 dcon, imsk, stoptries = 3; + + /* write DCON register */ + + if (!data) { + writel(0, host->base + S3C2410_SDIDCON); + return 0; + } + + while (readl(host->base + S3C2410_SDIDSTA) & + (S3C2410_SDIDSTA_TXDATAON | S3C2410_SDIDSTA_RXDATAON)) { + + dbg(host, dbg_err, + "mci_setup_data() transfer stillin progress.\n"); + + writel(0, host->base + S3C2410_SDIDCON); + s3cmci_reset(host); + + if ((stoptries--) == 0) { + dbg_dumpregs(host, "DRF"); + return -EINVAL; + } + } + + dcon = data->blocks & S3C2410_SDIDCON_BLKNUM_MASK; + + if (host->dodma) + dcon |= S3C2410_SDIDCON_DMAEN; + + if (host->bus_width == MMC_BUS_WIDTH_4) + dcon |= S3C2410_SDIDCON_WIDEBUS; + + if (!(data->flags & MMC_DATA_STREAM)) + dcon |= S3C2410_SDIDCON_BLOCKMODE; + + if (data->flags & MMC_DATA_WRITE) { + dcon |= S3C2410_SDIDCON_TXAFTERRESP; + dcon |= S3C2410_SDIDCON_XFER_TXSTART; + } + + if (data->flags & MMC_DATA_READ) { + dcon |= S3C2410_SDIDCON_RXAFTERCMD; + dcon |= S3C2410_SDIDCON_XFER_RXSTART; + } + + if (host->is2440) { + dcon |= S3C2440_SDIDCON_DS_WORD; + dcon |= S3C2440_SDIDCON_DATSTART; + } + + writel(dcon, host->base + S3C2410_SDIDCON); + + /* write BSIZE register */ + + writel(data->blksz, host->base + S3C2410_SDIBSIZE); + + /* add to IMASK register */ + imsk = S3C2410_SDIIMSK_FIFOFAIL | S3C2410_SDIIMSK_DATACRC | + S3C2410_SDIIMSK_DATATIMEOUT | S3C2410_SDIIMSK_DATAFINISH; + + enable_imask(host, imsk); + + /* write TIMER register */ + + if (host->is2440) { + writel(0x007FFFFF, host->base + S3C2410_SDITIMER); + } else { + writel(0x0000FFFF, host->base + S3C2410_SDITIMER); + + /* FIX: set slow clock to prevent timeouts on read */ + if (data->flags & MMC_DATA_READ) + writel(0xFF, host->base + S3C2410_SDIPRE); + } + + return 0; +} + +#define BOTH_DIR (MMC_DATA_WRITE | MMC_DATA_READ) + +static int s3cmci_prepare_pio(struct s3cmci_host *host, struct mmc_data *data) +{ + int rw = (data->flags & MMC_DATA_WRITE) ? 1 : 0; + + BUG_ON((data->flags & BOTH_DIR) == BOTH_DIR); + + host->pio_sgptr = 0; + host->pio_words = 0; + host->pio_count = 0; + host->pio_active = rw ? XFER_WRITE : XFER_READ; + + if (rw) { + do_pio_write(host); + enable_imask(host, S3C2410_SDIIMSK_TXFIFOHALF); + } else { + enable_imask(host, S3C2410_SDIIMSK_RXFIFOHALF + | S3C2410_SDIIMSK_RXFIFOLAST); + } + + return 0; +} + +static int s3cmci_prepare_dma(struct s3cmci_host *host, struct mmc_data *data) +{ + int dma_len, i; + int rw = (data->flags & MMC_DATA_WRITE) ? 1 : 0; + + BUG_ON((data->flags & BOTH_DIR) == BOTH_DIR); + + s3cmci_dma_setup(host, rw ? S3C2410_DMASRC_MEM : S3C2410_DMASRC_HW); + s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_FLUSH); + + dma_len = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len, + (rw) ? DMA_TO_DEVICE : DMA_FROM_DEVICE); + + if (dma_len == 0) + return -ENOMEM; + + host->dma_complete = 0; + host->dmatogo = dma_len; + + for (i = 0; i < dma_len; i++) { + int res; + + dbg(host, dbg_dma, "enqueue %i:%u@%u\n", i, + sg_dma_address(&data->sg[i]), + sg_dma_len(&data->sg[i])); + + res = s3c2410_dma_enqueue(host->dma, (void *) host, + sg_dma_address(&data->sg[i]), + sg_dma_len(&data->sg[i])); + + if (res) { + s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_FLUSH); + return -EBUSY; + } + } + + s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_START); + + return 0; +} + +static void s3cmci_send_request(struct mmc_host *mmc) +{ + struct s3cmci_host *host = mmc_priv(mmc); + struct mmc_request *mrq = host->mrq; + struct mmc_command *cmd = host->cmd_is_stop ? mrq->stop : mrq->cmd; + + host->ccnt++; + prepare_dbgmsg(host, cmd, host->cmd_is_stop); + + /* Clear command, data and fifo status registers + Fifo clear only necessary on 2440, but doesn't hurt on 2410 + */ + writel(0xFFFFFFFF, host->base + S3C2410_SDICMDSTAT); + writel(0xFFFFFFFF, host->base + S3C2410_SDIDSTA); + writel(0xFFFFFFFF, host->base + S3C2410_SDIFSTA); + + if (cmd->data) { + int res = s3cmci_setup_data(host, cmd->data); + + host->dcnt++; + + if (res) { + cmd->error = -EINVAL; + cmd->data->error = -EINVAL; + + mmc_request_done(mmc, mrq); + return; + } + + if (host->dodma) + res = s3cmci_prepare_dma(host, cmd->data); + else + res = s3cmci_prepare_pio(host, cmd->data); + + if (res) { + cmd->error = res; + cmd->data->error = res; + + mmc_request_done(mmc, mrq); + return; + } + } + + /* Send command */ + s3cmci_send_command(host, cmd); + + /* Enable Interrupt */ + enable_irq(host->irq); +} + +static void s3cmci_request(struct mmc_host *mmc, struct mmc_request *mrq) +{ + struct s3cmci_host *host = mmc_priv(mmc); + + host->status = "mmc request"; + host->cmd_is_stop = 0; + host->mrq = mrq; + + s3cmci_send_request(mmc); +} + +static void s3cmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct s3cmci_host *host = mmc_priv(mmc); + u32 mci_psc, mci_con; + + /* Set the power state */ + + mci_con = readl(host->base + S3C2410_SDICON); + + switch (ios->power_mode) { + case MMC_POWER_ON: + case MMC_POWER_UP: + s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_SDCLK); + s3c2410_gpio_cfgpin(S3C2410_GPE6, S3C2410_GPE6_SDCMD); + s3c2410_gpio_cfgpin(S3C2410_GPE7, S3C2410_GPE7_SDDAT0); + s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1); + s3c2410_gpio_cfgpin(S3C2410_GPE9, S3C2410_GPE9_SDDAT2); + s3c2410_gpio_cfgpin(S3C2410_GPE10, S3C2410_GPE10_SDDAT3); + + if (!host->is2440) + mci_con |= S3C2410_SDICON_FIFORESET; + + break; + + case MMC_POWER_OFF: + default: + s3c2410_gpio_setpin(S3C2410_GPE5, 0); + s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_OUTP); + + if (host->is2440) + mci_con |= S3C2440_SDICON_SDRESET; + + break; + } + + /* Set clock */ + for (mci_psc = 0; mci_psc < 255; mci_psc++) { + host->real_rate = host->clk_rate / (host->clk_div*(mci_psc+1)); + + if (host->real_rate <= ios->clock) + break; + } + + if (mci_psc > 255) + mci_psc = 255; + + host->prescaler = mci_psc; + writel(host->prescaler, host->base + S3C2410_SDIPRE); + + /* If requested clock is 0, real_rate will be 0, too */ + if (ios->clock == 0) + host->real_rate = 0; + + /* Set CLOCK_ENABLE */ + if (ios->clock) + mci_con |= S3C2410_SDICON_CLOCKTYPE; + else + mci_con &= ~S3C2410_SDICON_CLOCKTYPE; + + writel(mci_con, host->base + S3C2410_SDICON); + + if ((ios->power_mode == MMC_POWER_ON) || + (ios->power_mode == MMC_POWER_UP)) { + dbg(host, dbg_conf, "running at %lukHz (requested: %ukHz).\n", + host->real_rate/1000, ios->clock/1000); + } else { + dbg(host, dbg_conf, "powered down.\n"); + } + + host->bus_width = ios->bus_width; +} + +static void s3cmci_reset(struct s3cmci_host *host) +{ + u32 con = readl(host->base + S3C2410_SDICON); + + con |= S3C2440_SDICON_SDRESET; + writel(con, host->base + S3C2410_SDICON); +} + +static struct mmc_host_ops s3cmci_ops = { + .request = s3cmci_request, + .set_ios = s3cmci_set_ios, +}; + +static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) +{ + struct s3cmci_host *host; + struct mmc_host *mmc; + int ret; + + mmc = mmc_alloc_host(sizeof(struct s3cmci_host), &pdev->dev); + if (!mmc) { + ret = -ENOMEM; + goto probe_out; + } + + host = mmc_priv(mmc); + host->mmc = mmc; + host->pdev = pdev; + host->is2440 = is2440; + + spin_lock_init(&host->complete_lock); + tasklet_init(&host->pio_tasklet, pio_tasklet, (unsigned long) host); + + if (is2440) { + host->sdiimsk = S3C2440_SDIIMSK; + host->sdidata = S3C2440_SDIDATA; + host->clk_div = 1; + } else { + host->sdiimsk = S3C2410_SDIIMSK; + host->sdidata = S3C2410_SDIDATA; + host->clk_div = 2; + } + + host->dodma = 0; + host->complete_what = COMPLETION_NONE; + host->pio_active = XFER_NONE; + + host->dma = S3CMCI_DMA; + host->irq_cd = IRQ_EINT2; + + host->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!host->mem) { + dev_err(&pdev->dev, + "failed to get io memory region resouce.\n"); + + ret = -ENOENT; + goto probe_free_host; + } + + host->mem = request_mem_region(host->mem->start, + RESSIZE(host->mem), pdev->name); + + if (!host->mem) { + dev_err(&pdev->dev, "failed to request io memory region.\n"); + ret = -ENOENT; + goto probe_free_host; + } + + host->base = ioremap(host->mem->start, RESSIZE(host->mem)); + if (host->base == 0) { + dev_err(&pdev->dev, "failed to ioremap() io memory region.\n"); + ret = -EINVAL; + goto probe_free_mem_region; + } + + host->irq = platform_get_irq(pdev, 0); + if (host->irq == 0) { + dev_err(&pdev->dev, "failed to get interrupt resouce.\n"); + ret = -EINVAL; + goto probe_iounmap; + } + + if (request_irq(host->irq, s3cmci_irq, 0, DRIVER_NAME, host)) { + dev_err(&pdev->dev, "failed to request mci interrupt.\n"); + ret = -ENOENT; + goto probe_iounmap; + } + + /* We get spurious interrupts even when we have set the IMSK + * register to ignore everything, so use disable_irq() to make + * ensure we don't lock the system with un-serviceable requests. */ + + disable_irq(host->irq); + + s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_EINT2); + set_irq_type(host->irq_cd, IRQT_BOTHEDGE); + + if (request_irq(host->irq_cd, s3cmci_irq_cd, 0, DRIVER_NAME, host)) { + dev_err(&pdev->dev, + "failed to request card detect interrupt.\n"); + ret = -ENOENT; + goto probe_free_irq; + } + + if (s3c2410_dma_request(S3CMCI_DMA, &s3cmci_dma_client, NULL)) { + dev_err(&pdev->dev, "unable to get DMA channel.\n"); + ret = -EBUSY; + goto probe_free_irq_cd; + } + + host->clk = clk_get(&pdev->dev, "sdi"); + if (IS_ERR(host->clk)) { + dev_err(&pdev->dev, "failed to find clock source.\n"); + ret = PTR_ERR(host->clk); + host->clk = NULL; + goto probe_free_host; + } + + ret = clk_enable(host->clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable clock source.\n"); + goto clk_free; + } + + host->clk_rate = clk_get_rate(host->clk); + + mmc->ops = &s3cmci_ops; + mmc->ocr_avail = MMC_VDD_32_33; + mmc->caps = MMC_CAP_4_BIT_DATA; + mmc->f_min = host->clk_rate / (host->clk_div * 256); + mmc->f_max = host->clk_rate / host->clk_div; + + mmc->max_blk_count = 4095; + mmc->max_blk_size = 4095; + mmc->max_req_size = 4095 * 512; + mmc->max_seg_size = mmc->max_req_size; + + mmc->max_phys_segs = 128; + mmc->max_hw_segs = 128; + + dbg(host, dbg_debug, + "probe: mode:%s mapped mci_base:%p irq:%u irq_cd:%u dma:%u.\n", + (host->is2440?"2440":""), + host->base, host->irq, host->irq_cd, host->dma); + + ret = mmc_add_host(mmc); + if (ret) { + dev_err(&pdev->dev, "failed to add mmc host.\n"); + goto free_dmabuf; + } + + platform_set_drvdata(pdev, mmc); + dev_info(&pdev->dev, "initialisation done.\n"); + + return 0; + + free_dmabuf: + clk_disable(host->clk); + + clk_free: + clk_put(host->clk); + + probe_free_irq_cd: + free_irq(host->irq_cd, host); + + probe_free_irq: + free_irq(host->irq, host); + + probe_iounmap: + iounmap(host->base); + + probe_free_mem_region: + release_mem_region(host->mem->start, RESSIZE(host->mem)); + + probe_free_host: + mmc_free_host(mmc); + probe_out: + return ret; +} + +static int __devexit s3cmci_remove(struct platform_device *pdev) +{ + struct mmc_host *mmc = platform_get_drvdata(pdev); + struct s3cmci_host *host = mmc_priv(mmc); + + mmc_remove_host(mmc); + + clk_disable(host->clk); + clk_put(host->clk); + + tasklet_disable(&host->pio_tasklet); + + free_irq(host->irq_cd, host); + free_irq(host->irq, host); + + iounmap(host->base); + release_mem_region(host->mem->start, RESSIZE(host->mem)); + + mmc_free_host(mmc); + return 0; +} + +static int __devinit s3cmci_probe_2410(struct platform_device *dev) +{ + return s3cmci_probe(dev, 0); +} + +static int __devinit s3cmci_probe_2412(struct platform_device *dev) +{ + return s3cmci_probe(dev, 1); +} + +static int __devinit s3cmci_probe_2440(struct platform_device *dev) +{ + return s3cmci_probe(dev, 1); +} + +#ifdef CONFIG_PM + +static int s3cmci_suspend(struct platform_device *dev, pm_message_t state) +{ + struct mmc_host *mmc = platform_get_drvdata(dev); + + return mmc_suspend_host(mmc, state); +} + +static int s3cmci_resume(struct platform_device *dev) +{ + struct mmc_host *mmc = platform_get_drvdata(dev); + + return mmc_resume_host(mmc); +} + +#else /* CONFIG_PM */ +#define s3cmci_suspend NULL +#define s3cmci_resume NULL +#endif /* CONFIG_PM */ + + +static struct platform_driver s3cmci_driver_2410 = { + .driver.name = "s3c2410-sdi", + .driver.owner = THIS_MODULE, + .probe = s3cmci_probe_2410, + .remove = __devexit_p(s3cmci_remove), + .suspend = s3cmci_suspend, + .resume = s3cmci_resume, +}; + +static struct platform_driver s3cmci_driver_2412 = { + .driver.name = "s3c2412-sdi", + .driver.owner = THIS_MODULE, + .probe = s3cmci_probe_2412, + .remove = __devexit_p(s3cmci_remove), + .suspend = s3cmci_suspend, + .resume = s3cmci_resume, +}; + +static struct platform_driver s3cmci_driver_2440 = { + .driver.name = "s3c2440-sdi", + .driver.owner = THIS_MODULE, + .probe = s3cmci_probe_2440, + .remove = __devexit_p(s3cmci_remove), + .suspend = s3cmci_suspend, + .resume = s3cmci_resume, +}; + + +static int __init s3cmci_init(void) +{ + platform_driver_register(&s3cmci_driver_2410); + platform_driver_register(&s3cmci_driver_2412); + platform_driver_register(&s3cmci_driver_2440); + return 0; +} + +static void __exit s3cmci_exit(void) +{ + platform_driver_unregister(&s3cmci_driver_2410); + platform_driver_unregister(&s3cmci_driver_2412); + platform_driver_unregister(&s3cmci_driver_2440); +} + +module_init(s3cmci_init); +module_exit(s3cmci_exit); + +MODULE_DESCRIPTION("Samsung S3C MMC/SD Card Interface driver"); +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Thomas Kleffel "); diff --git a/drivers/mmc/host/s3cmci.h b/drivers/mmc/host/s3cmci.h new file mode 100644 index 0000000..90b8af7d --- /dev/null +++ b/drivers/mmc/host/s3cmci.h @@ -0,0 +1,69 @@ +/* + * linux/drivers/mmc/s3cmci.h - Samsung S3C MCI driver + * + * Copyright (C) 2004-2006 Thomas Kleffel, All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* FIXME: DMA Resource management ?! */ +#define S3CMCI_DMA 0 + +enum s3cmci_waitfor { + COMPLETION_NONE, + COMPLETION_FINALIZE, + COMPLETION_CMDSENT, + COMPLETION_RSPFIN, + COMPLETION_XFERFINISH, + COMPLETION_XFERFINISH_RSPFIN, +}; + +struct s3cmci_host { + struct platform_device *pdev; + struct mmc_host *mmc; + struct resource *mem; + struct clk *clk; + void __iomem *base; + int irq; + int irq_cd; + int dma; + + unsigned long clk_rate; + unsigned long clk_div; + unsigned long real_rate; + u8 prescaler; + + int is2440; + unsigned sdiimsk; + unsigned sdidata; + int dodma; + int dmatogo; + + struct mmc_request *mrq; + int cmd_is_stop; + + spinlock_t complete_lock; + enum s3cmci_waitfor complete_what; + + int dma_complete; + + u32 pio_sgptr; + u32 pio_words; + u32 pio_count; + u32 *pio_ptr; +#define XFER_NONE 0 +#define XFER_READ 1 +#define XFER_WRITE 2 + u32 pio_active; + + int bus_width; + + char dbgmsg_cmd[301]; + char dbgmsg_dat[301]; + char *status; + + unsigned int ccnt, dcnt; + struct tasklet_struct pio_tasklet; +}; diff --git a/include/asm-arm/arch-s3c2410/regs-sdi.h b/include/asm-arm/arch-s3c2410/regs-sdi.h index bb9d30b..bfb222f 100644 --- a/include/asm-arm/arch-s3c2410/regs-sdi.h +++ b/include/asm-arm/arch-s3c2410/regs-sdi.h @@ -28,9 +28,15 @@ #define S3C2410_SDIDCNT (0x30) #define S3C2410_SDIDSTA (0x34) #define S3C2410_SDIFSTA (0x38) + #define S3C2410_SDIDATA (0x3C) #define S3C2410_SDIIMSK (0x40) +#define S3C2440_SDIDATA (0x40) +#define S3C2440_SDIIMSK (0x3C) + +#define S3C2440_SDICON_SDRESET (1<<8) +#define S3C2440_SDICON_MMCCLOCK (1<<5) #define S3C2410_SDICON_BYTEORDER (1<<4) #define S3C2410_SDICON_SDIOIRQ (1<<3) #define S3C2410_SDICON_RWAITEN (1<<2) @@ -42,7 +48,8 @@ #define S3C2410_SDICMDCON_LONGRSP (1<<10) #define S3C2410_SDICMDCON_WAITRSP (1<<9) #define S3C2410_SDICMDCON_CMDSTART (1<<8) -#define S3C2410_SDICMDCON_INDEX (0xff) +#define S3C2410_SDICMDCON_SENDERHOST (1<<6) +#define S3C2410_SDICMDCON_INDEX (0x3f) #define S3C2410_SDICMDSTAT_CRCFAIL (1<<12) #define S3C2410_SDICMDSTAT_CMDSENT (1<<11) @@ -51,6 +58,9 @@ #define S3C2410_SDICMDSTAT_XFERING (1<<8) #define S3C2410_SDICMDSTAT_INDEX (0xff) +#define S3C2440_SDIDCON_DS_BYTE (0<<22) +#define S3C2440_SDIDCON_DS_HALFWORD (1<<22) +#define S3C2440_SDIDCON_DS_WORD (2<<22) #define S3C2410_SDIDCON_IRQPERIOD (1<<21) #define S3C2410_SDIDCON_TXAFTERRESP (1<<20) #define S3C2410_SDIDCON_RXAFTERCMD (1<<19) @@ -59,6 +69,7 @@ #define S3C2410_SDIDCON_WIDEBUS (1<<16) #define S3C2410_SDIDCON_DMAEN (1<<15) #define S3C2410_SDIDCON_STOP (1<<14) +#define S3C2440_SDIDCON_DATSTART (1<<14) #define S3C2410_SDIDCON_DATMODE (3<<12) #define S3C2410_SDIDCON_BLKNUM (0x7ff) @@ -68,6 +79,7 @@ #define S3C2410_SDIDCON_XFER_RXSTART (2<<12) #define S3C2410_SDIDCON_XFER_TXSTART (3<<12) +#define S3C2410_SDIDCON_BLKNUM_MASK (0xFFF) #define S3C2410_SDIDCNT_BLKNUM_SHIFT (12) #define S3C2410_SDIDSTA_RDYWAITREQ (1<<10) @@ -82,10 +94,12 @@ #define S3C2410_SDIDSTA_TXDATAON (1<<1) #define S3C2410_SDIDSTA_RXDATAON (1<<0) +#define S3C2440_SDIFSTA_FIFORESET (1<<16) +#define S3C2440_SDIFSTA_FIFOFAIL (3<<14) /* 3 is correct (2 bits) */ #define S3C2410_SDIFSTA_TFDET (1<<13) #define S3C2410_SDIFSTA_RFDET (1<<12) -#define S3C2410_SDIFSTA_TXHALF (1<<11) -#define S3C2410_SDIFSTA_TXEMPTY (1<<10) +#define S3C2410_SDIFSTA_TFHALF (1<<11) +#define S3C2410_SDIFSTA_TFEMPTY (1<<10) #define S3C2410_SDIFSTA_RFLAST (1<<9) #define S3C2410_SDIFSTA_RFFULL (1<<8) #define S3C2410_SDIFSTA_RFHALF (1<<7) -- cgit v1.1 From 679f0f8abd7187baaff40a47fe4733ae4c24cc9a Mon Sep 17 00:00:00 2001 From: Harald Welte Date: Mon, 30 Jun 2008 22:40:25 +0100 Subject: MMC: S3C24XX MMC/SD driver write fixes This patch is a workaround of some S3C2410 MMC chip bug Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index c6a4d3c..4db5bd7 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -461,9 +461,19 @@ static irqreturn_t s3cmci_irq(int irq, void *dev_id) if (mci_csta & S3C2410_SDICMDSTAT_CRCFAIL) { if (cmd->flags & MMC_RSP_CRC) { - cmd->error = -EILSEQ; - host->status = "error: bad command crc"; - goto fail_transfer; + if (host->mrq->cmd->flags & MMC_RSP_136) { + dbg(host, dbg_irq, + "fixup: ignore CRC fail with long rsp\n"); + } else { + /* note, we used to fail the transfer + * here, but it seems that this is just + * the hardware getting it wrong. + * + * cmd->error = -EILSEQ; + * host->status = "error: bad command crc"; + * goto fail_transfer; + */ + } } mci_cclear |= S3C2410_SDICMDSTAT_CRCFAIL; -- cgit v1.1 From ceb3ac252519f9ab318050c8ee842e62820d6731 Mon Sep 17 00:00:00 2001 From: Harald Welte Date: Mon, 30 Jun 2008 22:40:26 +0100 Subject: MMC: DMA free fix for S3C24XX SD/MMC driver Bugfix to ensure DMA channel allocated is freed on exit. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 4db5bd7..6070f36 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -1254,6 +1254,7 @@ static int __devexit s3cmci_remove(struct platform_device *pdev) clk_put(host->clk); tasklet_disable(&host->pio_tasklet); + s3c2410_dma_free(S3CMCI_DMA, &s3cmci_dma_client); free_irq(host->irq_cd, host); free_irq(host->irq, host); -- cgit v1.1 From bdbc9c3a8f7a7956611c970e262693faa95081a5 Mon Sep 17 00:00:00 2001 From: Thomas Kleffel Date: Mon, 30 Jun 2008 22:40:27 +0100 Subject: Fix the request finalisation by ensuring the controller is stopped. Signed-off-by: Ben Dooks Signed-off-by: Harald Welte Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 6070f36..8c68b2e 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -677,7 +677,7 @@ static void finalize_request(struct s3cmci_host *host) /* Cleanup controller */ writel(0, host->base + S3C2410_SDICMDARG); - writel(0, host->base + S3C2410_SDIDCON); + writel(S3C2410_SDIDCON_STOP, host->base + S3C2410_SDIDCON); writel(0, host->base + S3C2410_SDICMDCON); writel(0, host->base + host->sdiimsk); @@ -803,7 +803,7 @@ static int s3cmci_setup_data(struct s3cmci_host *host, struct mmc_data *data) dbg(host, dbg_err, "mci_setup_data() transfer stillin progress.\n"); - writel(0, host->base + S3C2410_SDIDCON); + writel(S3C2410_SDIDCON_STOP, host->base + S3C2410_SDIDCON); s3cmci_reset(host); if ((stoptries--) == 0) { -- cgit v1.1 From d643b5f7e0793ef7828a35a5ea049d675ad2ad8c Mon Sep 17 00:00:00 2001 From: Roman Moracik Date: Mon, 30 Jun 2008 22:40:28 +0100 Subject: MMC: Fix S3C24XX IRQ enable during PIO transfers Fix Bug #677 - I/O errors on heavy microSD writes for 2.6.22.x. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 8c68b2e..774af3d 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -335,6 +335,8 @@ static void pio_tasklet(unsigned long data) struct s3cmci_host *host = (struct s3cmci_host *) data; + disable_irq(host->irq); + if (host->pio_active == XFER_WRITE) do_pio_write(host); @@ -352,9 +354,9 @@ static void pio_tasklet(unsigned long data) host->mrq->data->error = -EINVAL; } - disable_irq(host->irq); finalize_request(host); - } + } else + enable_irq(host->irq); } /* @@ -630,7 +632,6 @@ out: spin_unlock_irqrestore(&host->complete_lock, iflags); return; - fail_request: host->mrq->data->error = -EINVAL; host->complete_what = COMPLETION_FINALIZE; -- cgit v1.1 From edb5a98e43682d66c98ddd1dee863d867807546e Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:29 +0100 Subject: MMC: S3C24XX: Add platform data for MMC/SD driver This patch adds platform data support to the s3mci driver. This allows flexible board-specific configuration of set_power, card detect and read only pins. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 44 +++++++++++++++++++++++++++++++++++--- drivers/mmc/host/s3cmci.h | 1 + include/asm-arm/plat-s3c24xx/mci.h | 12 +++++++++++ 3 files changed, 54 insertions(+), 3 deletions(-) create mode 100644 include/asm-arm/plat-s3c24xx/mci.h diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 774af3d..684a10c 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -21,6 +21,8 @@ #include #include +#include + #include "s3cmci.h" #define DRIVER_NAME "s3c-mci" @@ -1011,6 +1013,9 @@ static void s3cmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) s3c2410_gpio_cfgpin(S3C2410_GPE9, S3C2410_GPE9_SDDAT2); s3c2410_gpio_cfgpin(S3C2410_GPE10, S3C2410_GPE10_SDDAT3); + if (host->pdata->set_power) + host->pdata->set_power(ios->power_mode, ios->vdd); + if (!host->is2440) mci_con |= S3C2410_SDICON_FIFORESET; @@ -1024,6 +1029,9 @@ static void s3cmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) if (host->is2440) mci_con |= S3C2440_SDICON_SDRESET; + if (host->pdata->set_power) + host->pdata->set_power(ios->power_mode, ios->vdd); + break; } @@ -1072,9 +1080,25 @@ static void s3cmci_reset(struct s3cmci_host *host) writel(con, host->base + S3C2410_SDICON); } +static int s3cmci_get_ro(struct mmc_host *mmc) +{ + struct s3cmci_host *host = mmc_priv(mmc); + + if (host->pdata->gpio_wprotect == 0) + return 0; + + return s3c2410_gpio_getpin(host->pdata->gpio_wprotect); +} + static struct mmc_host_ops s3cmci_ops = { .request = s3cmci_request, .set_ios = s3cmci_set_ios, + .get_ro = s3cmci_get_ro, +}; + +static struct s3c24xx_mci_pdata s3cmci_def_pdata = { + /* This is currently here to avoid a number of if (host->pdata) + * checks. Any zero fields to ensure reaonable defaults are picked. */ }; static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) @@ -1094,6 +1118,12 @@ static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) host->pdev = pdev; host->is2440 = is2440; + host->pdata = pdev->dev.platform_data; + if (!host->pdata) { + pdev->dev.platform_data = &s3cmci_def_pdata; + host->pdata = &s3cmci_def_pdata; + } + spin_lock_init(&host->complete_lock); tasklet_init(&host->pio_tasklet, pio_tasklet, (unsigned long) host); @@ -1112,7 +1142,8 @@ static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) host->pio_active = XFER_NONE; host->dma = S3CMCI_DMA; - host->irq_cd = IRQ_EINT2; + host->irq_cd = s3c2410_gpio_getirq(host->pdata->gpio_detect); + s3c2410_gpio_cfgpin(host->pdata->gpio_detect, S3C2410_GPIO_IRQ); host->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!host->mem) { @@ -1158,7 +1189,7 @@ static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) disable_irq(host->irq); - s3c2410_gpio_cfgpin(S3C2410_GPF2, S3C2410_GPF2_EINT2); + s3c2410_gpio_cfgpin(host->pdata->gpio_detect, S3C2410_GPIO_IRQ); set_irq_type(host->irq_cd, IRQT_BOTHEDGE); if (request_irq(host->irq_cd, s3cmci_irq_cd, 0, DRIVER_NAME, host)) { @@ -1168,6 +1199,10 @@ static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) goto probe_free_irq; } + if (host->pdata->gpio_wprotect) + s3c2410_gpio_cfgpin(host->pdata->gpio_wprotect, + S3C2410_GPIO_INPUT); + if (s3c2410_dma_request(S3CMCI_DMA, &s3cmci_dma_client, NULL)) { dev_err(&pdev->dev, "unable to get DMA channel.\n"); ret = -EBUSY; @@ -1191,11 +1226,14 @@ static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) host->clk_rate = clk_get_rate(host->clk); mmc->ops = &s3cmci_ops; - mmc->ocr_avail = MMC_VDD_32_33; + mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; mmc->caps = MMC_CAP_4_BIT_DATA; mmc->f_min = host->clk_rate / (host->clk_div * 256); mmc->f_max = host->clk_rate / host->clk_div; + if (host->pdata->ocr_avail) + mmc->ocr_avail = host->pdata->ocr_avail; + mmc->max_blk_count = 4095; mmc->max_blk_size = 4095; mmc->max_req_size = 4095 * 512; diff --git a/drivers/mmc/host/s3cmci.h b/drivers/mmc/host/s3cmci.h index 90b8af7d..37d9c60 100644 --- a/drivers/mmc/host/s3cmci.h +++ b/drivers/mmc/host/s3cmci.h @@ -22,6 +22,7 @@ enum s3cmci_waitfor { struct s3cmci_host { struct platform_device *pdev; + struct s3c24xx_mci_pdata *pdata; struct mmc_host *mmc; struct resource *mem; struct clk *clk; diff --git a/include/asm-arm/plat-s3c24xx/mci.h b/include/asm-arm/plat-s3c24xx/mci.h new file mode 100644 index 0000000..5be2c14 --- /dev/null +++ b/include/asm-arm/plat-s3c24xx/mci.h @@ -0,0 +1,12 @@ +#ifndef _ARCH_MCI_H +#define _ARCH_MCI_H + +struct s3c24xx_mci_pdata { + unsigned int gpio_detect; + unsigned int gpio_wprotect; + unsigned long ocr_avail; + void (*set_power)(unsigned char power_mode, + unsigned short vdd); +}; + +#endif /* _ARCH_NCI_H */ -- cgit v1.1 From cf0984c8edf63017fcc2ead212ca057877e345df Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:30 +0100 Subject: MMC: S3C24XX: Add support to invert write protect line Support for inverting the sense of the MMC driver's write protect detection line. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 11 +++++++++-- include/asm-arm/plat-s3c24xx/mci.h | 2 ++ 2 files changed, 11 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 684a10c..4fd11d8 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -1083,11 +1083,18 @@ static void s3cmci_reset(struct s3cmci_host *host) static int s3cmci_get_ro(struct mmc_host *mmc) { struct s3cmci_host *host = mmc_priv(mmc); + struct s3c24xx_mci_pdata *pdata = host->pdata; + int ret; - if (host->pdata->gpio_wprotect == 0) + if (pdata->gpio_wprotect == 0) return 0; - return s3c2410_gpio_getpin(host->pdata->gpio_wprotect); + ret = s3c2410_gpio_getpin(pdata->gpio_wprotect); + + if (pdata->wprotect_invert) + ret = !ret; + + return ret; } static struct mmc_host_ops s3cmci_ops = { diff --git a/include/asm-arm/plat-s3c24xx/mci.h b/include/asm-arm/plat-s3c24xx/mci.h index 5be2c14..4f4ccd18 100644 --- a/include/asm-arm/plat-s3c24xx/mci.h +++ b/include/asm-arm/plat-s3c24xx/mci.h @@ -2,6 +2,8 @@ #define _ARCH_MCI_H struct s3c24xx_mci_pdata { + unsigned int wprotect_invert : 1; + unsigned int gpio_detect; unsigned int gpio_wprotect; unsigned long ocr_avail; -- cgit v1.1 From 7c14450ed6ab4ed453b2bf216ca3aaa7a5402af3 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:31 +0100 Subject: MMC: S3C24XX: Ensure host->mrq->data is valid Fix a crash if host->mrq->data is NULL on ending a transfer. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 4fd11d8..ffd9269 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -353,7 +353,8 @@ static void pio_tasklet(unsigned long data) (host->pio_active == XFER_READ) ? "read" : "write", host->pio_count, host->pio_words); - host->mrq->data->error = -EINVAL; + if (host->mrq->data) + host->mrq->data->error = -EINVAL; } finalize_request(host); -- cgit v1.1 From 55d70f5a7b25800fc8376cdd81d42d6c201fa91d Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:32 +0100 Subject: MMC: S3C24XX: Allow card-detect on non-IRQ capable pin Add support to the S3C24XX MMC driver to have the card detect be on a pin that is not IRQ capable. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 28 +++++++++++++++++----------- 1 file changed, 17 insertions(+), 11 deletions(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index ffd9269..aa9a8b4 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -1150,8 +1150,6 @@ static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) host->pio_active = XFER_NONE; host->dma = S3CMCI_DMA; - host->irq_cd = s3c2410_gpio_getirq(host->pdata->gpio_detect); - s3c2410_gpio_cfgpin(host->pdata->gpio_detect, S3C2410_GPIO_IRQ); host->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!host->mem) { @@ -1197,14 +1195,20 @@ static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) disable_irq(host->irq); - s3c2410_gpio_cfgpin(host->pdata->gpio_detect, S3C2410_GPIO_IRQ); - set_irq_type(host->irq_cd, IRQT_BOTHEDGE); + host->irq_cd = s3c2410_gpio_getirq(host->pdata->gpio_detect); - if (request_irq(host->irq_cd, s3cmci_irq_cd, 0, DRIVER_NAME, host)) { - dev_err(&pdev->dev, - "failed to request card detect interrupt.\n"); - ret = -ENOENT; - goto probe_free_irq; + if (host->irq_cd >= 0) { + if (request_irq(host->irq_cd, s3cmci_irq_cd, + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + DRIVER_NAME, host)) { + dev_err(&pdev->dev, "can't get card detect irq.\n"); + ret = -ENOENT; + goto probe_free_irq; + } + } else { + dev_warn(&pdev->dev, "host detect has no irq available\n"); + s3c2410_gpio_cfgpin(host->pdata->gpio_detect, + S3C2410_GPIO_INPUT); } if (host->pdata->gpio_wprotect) @@ -1273,7 +1277,8 @@ static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) clk_put(host->clk); probe_free_irq_cd: - free_irq(host->irq_cd, host); + if (host->irq_cd >= 0) + free_irq(host->irq_cd, host); probe_free_irq: free_irq(host->irq, host); @@ -1303,7 +1308,8 @@ static int __devexit s3cmci_remove(struct platform_device *pdev) tasklet_disable(&host->pio_tasklet); s3c2410_dma_free(S3CMCI_DMA, &s3cmci_dma_client); - free_irq(host->irq_cd, host); + if (host->irq_cd >= 0) + free_irq(host->irq_cd, host); free_irq(host->irq, host); iounmap(host->base); -- cgit v1.1 From 3886ff5f63f33c801ed3af265ac0df20d3a8dcf5 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:33 +0100 Subject: MMC: S3C24XX: Fix s3c2410_dma_request() return code check. The driver should be checking for a negative error code from s3c2410_dma_request(), not non-zero. Newer kernels now return the DMA channel number that was allocated by the request. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index aa9a8b4..8389107 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -1215,7 +1215,7 @@ static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440) s3c2410_gpio_cfgpin(host->pdata->gpio_wprotect, S3C2410_GPIO_INPUT); - if (s3c2410_dma_request(S3CMCI_DMA, &s3cmci_dma_client, NULL)) { + if (s3c2410_dma_request(S3CMCI_DMA, &s3cmci_dma_client, NULL) < 0) { dev_err(&pdev->dev, "unable to get DMA channel.\n"); ret = -EBUSY; goto probe_free_irq_cd; -- cgit v1.1 From 318f905f02b427b8df33d724b7392a0597b40bdd Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:34 +0100 Subject: MMC: S3C24XX: Add MODULE_ALIAS() entries for the platform devices Add MODULE_ALIAS() declerations for all the supported platform devices for this driver. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 8389107..a6224f9 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -1405,3 +1405,6 @@ module_exit(s3cmci_exit); MODULE_DESCRIPTION("Samsung S3C MMC/SD Card Interface driver"); MODULE_LICENSE("GPL v2"); MODULE_AUTHOR("Thomas Kleffel "); +MODULE_ALIAS("platform:s3c2410-sdi"); +MODULE_ALIAS("platform:s3c2412-sdi"); +MODULE_ALIAS("platform:s3c2440-sdi"); -- cgit v1.1 From 2de5f79d4dfcb1be16f0b873bc77d6ec74b0426d Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:35 +0100 Subject: MMC: S3C24XX: Fix use of msecs where jiffies are needed mmc_detect_change() takes jiffies, not msecs. Convert the previous value of msecs into jiffies before calling. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index a6224f9..6f1b474 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -584,7 +584,7 @@ static irqreturn_t s3cmci_irq_cd(int irq, void *dev_id) dbg(host, dbg_irq, "card detect\n"); - mmc_detect_change(host->mmc, 500); + mmc_detect_change(host->mmc, msecs_to_jiffies(500)); return IRQ_HANDLED; } -- cgit v1.1 From 50a845700b3b55f825b0eb901b03d6091f66d9f4 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:36 +0100 Subject: MMC: S3C24XX: Add media presence test to request handling. Ensure that we have physical media present before attempting to send a request to a card. This ensures that we do not get flooded by errors from commands that can never be completed timing out. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 19 ++++++++++++++++++- include/asm-arm/plat-s3c24xx/mci.h | 1 + 2 files changed, 19 insertions(+), 1 deletion(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 6f1b474..62d73d3 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -984,6 +984,18 @@ static void s3cmci_send_request(struct mmc_host *mmc) enable_irq(host->irq); } +static int s3cmci_card_present(struct s3cmci_host *host) +{ + struct s3c24xx_mci_pdata *pdata = host->pdata; + int ret; + + if (pdata->gpio_detect == 0) + return -ENOSYS; + + ret = s3c2410_gpio_getpin(pdata->gpio_detect) ? 0 : 1; + return ret ^ pdata->detect_invert; +} + static void s3cmci_request(struct mmc_host *mmc, struct mmc_request *mrq) { struct s3cmci_host *host = mmc_priv(mmc); @@ -992,7 +1004,12 @@ static void s3cmci_request(struct mmc_host *mmc, struct mmc_request *mrq) host->cmd_is_stop = 0; host->mrq = mrq; - s3cmci_send_request(mmc); + if (s3cmci_card_present(host) == 0) { + dbg(host, dbg_err, "%s: no medium present\n", __func__); + host->mrq->cmd->error = -ENOMEDIUM; + mmc_request_done(mmc, mrq); + } else + s3cmci_send_request(mmc); } static void s3cmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) diff --git a/include/asm-arm/plat-s3c24xx/mci.h b/include/asm-arm/plat-s3c24xx/mci.h index 4f4ccd18..2d0852a 100644 --- a/include/asm-arm/plat-s3c24xx/mci.h +++ b/include/asm-arm/plat-s3c24xx/mci.h @@ -3,6 +3,7 @@ struct s3c24xx_mci_pdata { unsigned int wprotect_invert : 1; + unsigned int detect_invert : 1; /* set => detect active high. */ unsigned int gpio_detect; unsigned int gpio_wprotect; -- cgit v1.1 From ff8c804f1fdecb198c4be57155c61800e0d37bd2 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:37 +0100 Subject: MMC: S3C24XX: Update error debugging. Add better debugging to show where errors are being generated, as some error codes can come from several different code paths. Also fix the error return path from s3cmci_setup_data() to return the error it returned to the request. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 62d73d3..2b48395 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -450,6 +450,7 @@ static irqreturn_t s3cmci_irq(int irq, void *dev_id) } if (mci_csta & S3C2410_SDICMDSTAT_CMDTIMEOUT) { + dbg(host, dbg_err, "CMDSTAT: error CMDTIMEOUT\n"); cmd->error = -ETIMEDOUT; host->status = "error: command timeout"; goto fail_transfer; @@ -505,12 +506,14 @@ static irqreturn_t s3cmci_irq(int irq, void *dev_id) /* Check for FIFO failure */ if (host->is2440) { if (mci_fsta & S3C2440_SDIFSTA_FIFOFAIL) { + dbg(host, dbg_err, "FIFO failure\n"); host->mrq->data->error = -EILSEQ; host->status = "error: 2440 fifo failure"; goto fail_transfer; } } else { if (mci_dsta & S3C2410_SDIDSTA_FIFOFAIL) { + dbg(host, dbg_err, "FIFO failure\n"); cmd->data->error = -EILSEQ; host->status = "error: fifo failure"; goto fail_transfer; @@ -518,18 +521,21 @@ static irqreturn_t s3cmci_irq(int irq, void *dev_id) } if (mci_dsta & S3C2410_SDIDSTA_RXCRCFAIL) { + dbg(host, dbg_err, "bad data crc (outgoing)\n"); cmd->data->error = -EILSEQ; host->status = "error: bad data crc (outgoing)"; goto fail_transfer; } if (mci_dsta & S3C2410_SDIDSTA_CRCFAIL) { + dbg(host, dbg_err, "bad data crc (incoming)\n"); cmd->data->error = -EILSEQ; host->status = "error: bad data crc (incoming)"; goto fail_transfer; } if (mci_dsta & S3C2410_SDIDSTA_DATATIMEOUT) { + dbg(host, dbg_err, "data timeout\n"); cmd->data->error = -ETIMEDOUT; host->status = "error: data timeout"; goto fail_transfer; @@ -956,8 +962,9 @@ static void s3cmci_send_request(struct mmc_host *mmc) host->dcnt++; if (res) { - cmd->error = -EINVAL; - cmd->data->error = -EINVAL; + dbg(host, dbg_err, "setup data error %d\n", res); + cmd->error = res; + cmd->data->error = res; mmc_request_done(mmc, mrq); return; @@ -969,6 +976,7 @@ static void s3cmci_send_request(struct mmc_host *mmc) res = s3cmci_prepare_pio(host, cmd->data); if (res) { + dbg(host, dbg_err, "data prepare error %d\n", res); cmd->error = res; cmd->data->error = res; -- cgit v1.1 From 4dde7f755211fd58105c989a99a3a9f2f1238fba Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:38 +0100 Subject: MMC: S3C24XX: Add maintainer entry Add Ben Dooks as S3C24XX SD/MMC driver maintainer. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- MAINTAINERS | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index f140449..9def20a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3530,6 +3530,13 @@ L: linux-s390@vger.kernel.org W: http://www.ibm.com/developerworks/linux/linux390/ S: Supported +S3C24XX SD/MMC Driver +P: Ben Dooks +M: ben-linux@fluff.org +L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only) +L: linux-kernel@vger.kernel.org +S: Supported + SAA7146 VIDEO4LINUX-2 DRIVER P: Michael Hunold M: michael@mihu.de -- cgit v1.1 From 7e9c7b64022b7faff6022df64baec8ab467d0bfd Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Mon, 30 Jun 2008 22:40:39 +0100 Subject: MMC: S3C24XX: Refuse incorrectly aligned transfers The hardware does not support any multi-block transfers with an block-size that is not 32bit aligned. Also the driver itself does not support single block non-32bit transfers either. Ensure that the s3cmci_setup_data() returns the appropriate error if we encounter this. Signed-off-by: Ben Dooks Signed-off-by: Pierre Ossman --- drivers/mmc/host/s3cmci.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c index 2b48395..6a1e499 100644 --- a/drivers/mmc/host/s3cmci.c +++ b/drivers/mmc/host/s3cmci.c @@ -807,6 +807,17 @@ static int s3cmci_setup_data(struct s3cmci_host *host, struct mmc_data *data) return 0; } + if ((data->blksz & 3) != 0) { + /* We cannot deal with unaligned blocks with more than + * one block being transfered. */ + + if (data->blocks > 1) + return -EINVAL; + + /* No support yet for non-word block transfers. */ + return -EINVAL; + } + while (readl(host->base + S3C2410_SDIDSTA) & (S3C2410_SDIDSTA_TXDATAON | S3C2410_SDIDSTA_RXDATAON)) { -- cgit v1.1 From 9eeebd22ca757fee8dc10ffe6fa6992f33a3c5ec Mon Sep 17 00:00:00 2001 From: Tomas Winkler Date: Mon, 30 Jun 2008 10:50:23 +0300 Subject: mmc: wbsd.c fix shadowing of 'dma' variable This patch fix warning :shadowing dma variable and made use of module_param_named instead of module_param Signed-off-by: Tomas Winkler Acked-by: Marcel Holtmann Signed-off-by: Pierre Ossman --- drivers/mmc/host/wbsd.c | 30 +++++++++++++++--------------- 1 file changed, 15 insertions(+), 15 deletions(-) diff --git a/drivers/mmc/host/wbsd.c b/drivers/mmc/host/wbsd.c index 67e5a9b..c2b6160 100644 --- a/drivers/mmc/host/wbsd.c +++ b/drivers/mmc/host/wbsd.c @@ -68,16 +68,16 @@ static const int unlock_codes[] = { 0x83, 0x87 }; static const int valid_ids[] = { 0x7112, - }; +}; #ifdef CONFIG_PNP -static unsigned int nopnp = 0; +static unsigned int param_nopnp = 0; #else -static const unsigned int nopnp = 1; +static const unsigned int param_nopnp = 1; #endif -static unsigned int io = 0x248; -static unsigned int irq = 6; -static int dma = 2; +static unsigned int param_io = 0x248; +static unsigned int param_irq = 6; +static int param_dma = 2; /* * Basic functions @@ -1765,7 +1765,7 @@ static void __devexit wbsd_shutdown(struct device *dev, int pnp) static int __devinit wbsd_probe(struct platform_device *dev) { /* Use the module parameters for resources */ - return wbsd_init(&dev->dev, io, irq, dma, 0); + return wbsd_init(&dev->dev, param_io, param_irq, param_dma, 0); } static int __devexit wbsd_remove(struct platform_device *dev) @@ -1979,14 +1979,14 @@ static int __init wbsd_drv_init(void) #ifdef CONFIG_PNP - if (!nopnp) { + if (!param_nopnp) { result = pnp_register_driver(&wbsd_pnp_driver); if (result < 0) return result; } #endif /* CONFIG_PNP */ - if (nopnp) { + if (param_nopnp) { result = platform_driver_register(&wbsd_driver); if (result < 0) return result; @@ -2012,12 +2012,12 @@ static void __exit wbsd_drv_exit(void) { #ifdef CONFIG_PNP - if (!nopnp) + if (!param_nopnp) pnp_unregister_driver(&wbsd_pnp_driver); #endif /* CONFIG_PNP */ - if (nopnp) { + if (param_nopnp) { platform_device_unregister(wbsd_device); platform_driver_unregister(&wbsd_driver); @@ -2029,11 +2029,11 @@ static void __exit wbsd_drv_exit(void) module_init(wbsd_drv_init); module_exit(wbsd_drv_exit); #ifdef CONFIG_PNP -module_param(nopnp, uint, 0444); +module_param_named(nopnp, param_nopnp, uint, 0444); #endif -module_param(io, uint, 0444); -module_param(irq, uint, 0444); -module_param(dma, int, 0444); +module_param_named(io, param_io, uint, 0444); +module_param_named(irq, param_irq, uint, 0444); +module_param_named(dma, param_dma, int, 0444); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Pierre Ossman "); -- cgit v1.1 From 6d37333163025b46afbcad434ec9a5f2e88e7254 Mon Sep 17 00:00:00 2001 From: Tomas Winkler Date: Mon, 30 Jun 2008 10:50:24 +0300 Subject: mmc: fix sdio_io sparse errors This patch fixes sdio_io sparse errors. This fix changes signature of API functions, changing unsigned char -> u8 unsigned short -> u16 unsigned long -> u32 - this was probably a bug in 64 bit platforms Signed-off-by: Tomas Winkler Signed-off-by: Pierre Ossman --- drivers/mmc/core/sdio_io.c | 42 ++++++++++++++++-------------------------- include/linux/mmc/sdio_func.h | 15 ++++++--------- 2 files changed, 22 insertions(+), 35 deletions(-) mode change 100644 => 100755 drivers/mmc/core/sdio_io.c mode change 100644 => 100755 include/linux/mmc/sdio_func.h diff --git a/drivers/mmc/core/sdio_io.c b/drivers/mmc/core/sdio_io.c old mode 100644 new mode 100755 index cc42a41..3ccf691 --- a/drivers/mmc/core/sdio_io.c +++ b/drivers/mmc/core/sdio_io.c @@ -167,10 +167,8 @@ int sdio_set_block_size(struct sdio_func *func, unsigned blksz) return -EINVAL; if (blksz == 0) { - blksz = min(min( - func->max_blksize, - func->card->host->max_blk_size), - 512u); + blksz = min(func->max_blksize, func->card->host->max_blk_size); + blksz = min(blksz, 512u); } ret = mmc_io_rw_direct(func->card, 1, 0, @@ -311,10 +309,9 @@ static int sdio_io_rw_ext_helper(struct sdio_func *func, int write, /* Blocks per command is limited by host count, host transfer * size (we only use a single sg entry) and the maximum for * IO_RW_EXTENDED of 511 blocks. */ - max_blocks = min(min( - func->card->host->max_blk_count, - func->card->host->max_seg_size / func->cur_blksize), - 511u); + max_blocks = min(func->card->host->max_blk_count, + func->card->host->max_seg_size / func->cur_blksize); + max_blocks = min(max_blocks, 511u); while (remainder > func->cur_blksize) { unsigned blocks; @@ -364,11 +361,10 @@ static int sdio_io_rw_ext_helper(struct sdio_func *func, int write, * function. If there is a problem reading the address, 0xff * is returned and @err_ret will contain the error code. */ -unsigned char sdio_readb(struct sdio_func *func, unsigned int addr, - int *err_ret) +u8 sdio_readb(struct sdio_func *func, unsigned int addr, int *err_ret) { int ret; - unsigned char val; + u8 val; BUG_ON(!func); @@ -397,8 +393,7 @@ EXPORT_SYMBOL_GPL(sdio_readb); * function. @err_ret will contain the status of the actual * transfer. */ -void sdio_writeb(struct sdio_func *func, unsigned char b, unsigned int addr, - int *err_ret) +void sdio_writeb(struct sdio_func *func, u8 b, unsigned int addr, int *err_ret) { int ret; @@ -459,7 +454,6 @@ int sdio_readsb(struct sdio_func *func, void *dst, unsigned int addr, { return sdio_io_rw_ext_helper(func, 0, addr, 0, dst, count); } - EXPORT_SYMBOL_GPL(sdio_readsb); /** @@ -489,8 +483,7 @@ EXPORT_SYMBOL_GPL(sdio_writesb); * function. If there is a problem reading the address, 0xffff * is returned and @err_ret will contain the error code. */ -unsigned short sdio_readw(struct sdio_func *func, unsigned int addr, - int *err_ret) +u16 sdio_readw(struct sdio_func *func, unsigned int addr, int *err_ret) { int ret; @@ -504,7 +497,7 @@ unsigned short sdio_readw(struct sdio_func *func, unsigned int addr, return 0xFFFF; } - return le16_to_cpu(*(u16*)func->tmpbuf); + return le16_to_cpup((__le16 *)func->tmpbuf); } EXPORT_SYMBOL_GPL(sdio_readw); @@ -519,12 +512,11 @@ EXPORT_SYMBOL_GPL(sdio_readw); * function. @err_ret will contain the status of the actual * transfer. */ -void sdio_writew(struct sdio_func *func, unsigned short b, unsigned int addr, - int *err_ret) +void sdio_writew(struct sdio_func *func, u16 b, unsigned int addr, int *err_ret) { int ret; - *(u16*)func->tmpbuf = cpu_to_le16(b); + *(__le16 *)func->tmpbuf = cpu_to_le16(b); ret = sdio_memcpy_toio(func, addr, func->tmpbuf, 2); if (err_ret) @@ -543,8 +535,7 @@ EXPORT_SYMBOL_GPL(sdio_writew); * 0xffffffff is returned and @err_ret will contain the error * code. */ -unsigned long sdio_readl(struct sdio_func *func, unsigned int addr, - int *err_ret) +u32 sdio_readl(struct sdio_func *func, unsigned int addr, int *err_ret) { int ret; @@ -558,7 +549,7 @@ unsigned long sdio_readl(struct sdio_func *func, unsigned int addr, return 0xFFFFFFFF; } - return le32_to_cpu(*(u32*)func->tmpbuf); + return le32_to_cpup((__le32 *)func->tmpbuf); } EXPORT_SYMBOL_GPL(sdio_readl); @@ -573,12 +564,11 @@ EXPORT_SYMBOL_GPL(sdio_readl); * function. @err_ret will contain the status of the actual * transfer. */ -void sdio_writel(struct sdio_func *func, unsigned long b, unsigned int addr, - int *err_ret) +void sdio_writel(struct sdio_func *func, u32 b, unsigned int addr, int *err_ret) { int ret; - *(u32*)func->tmpbuf = cpu_to_le32(b); + *(__le32 *)func->tmpbuf = cpu_to_le32(b); ret = sdio_memcpy_toio(func, addr, func->tmpbuf, 4); if (err_ret) diff --git a/include/linux/mmc/sdio_func.h b/include/linux/mmc/sdio_func.h old mode 100644 new mode 100755 index f57f22b..28fb0a3 --- a/include/linux/mmc/sdio_func.h +++ b/include/linux/mmc/sdio_func.h @@ -122,23 +122,20 @@ extern int sdio_release_irq(struct sdio_func *func); extern unsigned int sdio_align_size(struct sdio_func *func, unsigned int sz); -extern unsigned char sdio_readb(struct sdio_func *func, - unsigned int addr, int *err_ret); -extern unsigned short sdio_readw(struct sdio_func *func, - unsigned int addr, int *err_ret); -extern unsigned long sdio_readl(struct sdio_func *func, - unsigned int addr, int *err_ret); +extern u8 sdio_readb(struct sdio_func *func, unsigned int addr, int *err_ret); +extern u16 sdio_readw(struct sdio_func *func, unsigned int addr, int *err_ret); +extern u32 sdio_readl(struct sdio_func *func, unsigned int addr, int *err_ret); extern int sdio_memcpy_fromio(struct sdio_func *func, void *dst, unsigned int addr, int count); extern int sdio_readsb(struct sdio_func *func, void *dst, unsigned int addr, int count); -extern void sdio_writeb(struct sdio_func *func, unsigned char b, +extern void sdio_writeb(struct sdio_func *func, u8 b, unsigned int addr, int *err_ret); -extern void sdio_writew(struct sdio_func *func, unsigned short b, +extern void sdio_writew(struct sdio_func *func, u16 b, unsigned int addr, int *err_ret); -extern void sdio_writel(struct sdio_func *func, unsigned long b, +extern void sdio_writel(struct sdio_func *func, u32 b, unsigned int addr, int *err_ret); extern int sdio_memcpy_toio(struct sdio_func *func, unsigned int addr, -- cgit v1.1 From 7d2be0749a59096a334c94dc48f43294193cb8ed Mon Sep 17 00:00:00 2001 From: Haavard Skinnemoen Date: Mon, 30 Jun 2008 18:35:03 +0200 Subject: atmel-mci: Driver for Atmel on-chip MMC controllers This is a driver for the MMC controller on the AP7000 chips from Atmel. It should in theory work on AT91 systems too with some tweaking, but since the DMA interface is quite different, it's not entirely clear if it's worth merging this with the at91_mci driver. This driver has been around for a while in BSPs and kernel sources provided by Atmel, but this particular version uses the generic DMA Engine framework (with the slave extensions) instead of an avr32-only DMA controller framework. This driver can also use PIO transfers when no DMA channels are available, and for transfers where using DMA may be difficult or impractical for some reason (e.g. the DMA setup overhead is usually not worth it for very short transfers, and badly aligned buffers or lengths are difficult to handle.) Currently, the driver only support PIO transfers. DMA support has been split out to a separate patch to hopefully make it easier to review. The driver has been tested using mmc-block and ext3fs on several SD, SDHC and MMC+ cards. Reads and writes work fine, with read transfer rates up to 3.5 MiB/s on fast cards with debugging disabled. The driver has also been tested using the mmc_test module on the same cards. All tests except 7, 9, 15 and 17 succeed. The first two are unsupported by all the cards I have, so I don't know if the driver handles this correctly. The last two fail because the hardware flags a Data CRC Error instead of a Data Timeout error. I'm not sure how to deal with that. Documentation for this controller can be found in many data sheets from Atmel, including the AT32AP7000 data sheet which can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Signed-off-by: Haavard Skinnemoen Signed-off-by: Pierre Ossman --- arch/avr32/boards/atngw100/setup.c | 7 + arch/avr32/boards/atstk1000/atstk1002.c | 3 + arch/avr32/mach-at32ap/at32ap700x.c | 30 +- drivers/mmc/host/Kconfig | 10 + drivers/mmc/host/Makefile | 1 + drivers/mmc/host/atmel-mci-regs.h | 91 +++ drivers/mmc/host/atmel-mci.c | 981 ++++++++++++++++++++++++++++++++ include/asm-avr32/arch-at32ap/board.h | 6 +- include/asm-avr32/atmel-mci.h | 9 + 9 files changed, 1132 insertions(+), 6 deletions(-) create mode 100644 drivers/mmc/host/atmel-mci-regs.h create mode 100644 drivers/mmc/host/atmel-mci.c create mode 100644 include/asm-avr32/atmel-mci.h diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c index a51bb9f..c7fe94d 100644 --- a/arch/avr32/boards/atngw100/setup.c +++ b/arch/avr32/boards/atngw100/setup.c @@ -19,6 +19,7 @@ #include #include +#include #include #include @@ -51,6 +52,11 @@ static struct spi_board_info spi0_board_info[] __initdata = { }, }; +static struct mci_platform_data __initdata mci0_data = { + .detect_pin = GPIO_PIN_PC(25), + .wp_pin = GPIO_PIN_PE(0), +}; + /* * The next two functions should go away as the boot loader is * supposed to initialize the macb address registers with a valid @@ -170,6 +176,7 @@ static int __init atngw100_init(void) set_hw_addr(at32_add_device_eth(1, ð_data[1])); at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info)); + at32_add_device_mci(0, &mci0_data); at32_add_device_usba(0, NULL); for (i = 0; i < ARRAY_SIZE(ngw_leds); i++) { diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c index 86b363c..e11659b 100644 --- a/arch/avr32/boards/atstk1000/atstk1002.c +++ b/arch/avr32/boards/atstk1000/atstk1002.c @@ -234,6 +234,9 @@ static int __init atstk1002_init(void) #ifdef CONFIG_BOARD_ATSTK100X_SPI1 at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif +#ifndef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM + at32_add_device_mci(0, NULL); +#endif #ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM set_hw_addr(at32_add_device_eth(1, ð_data[1])); #else diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c index 07b21b1..021d512 100644 --- a/arch/avr32/mach-at32ap/at32ap700x.c +++ b/arch/avr32/mach-at32ap/at32ap700x.c @@ -14,6 +14,7 @@ #include #include +#include #include #include @@ -1278,20 +1279,32 @@ static struct clk atmel_mci0_pclk = { .index = 9, }; -struct platform_device *__init at32_add_device_mci(unsigned int id) +struct platform_device *__init +at32_add_device_mci(unsigned int id, struct mci_platform_data *data) { - struct platform_device *pdev; + struct mci_platform_data _data; + struct platform_device *pdev; + struct dw_dma_slave *dws; if (id != 0) return NULL; pdev = platform_device_alloc("atmel_mci", id); if (!pdev) - return NULL; + goto fail; if (platform_device_add_resources(pdev, atmel_mci0_resource, ARRAY_SIZE(atmel_mci0_resource))) - goto err_add_resources; + goto fail; + + if (!data) { + data = &_data; + memset(data, 0, sizeof(struct mci_platform_data)); + } + + if (platform_device_add_data(pdev, data, + sizeof(struct mci_platform_data))) + goto fail; select_peripheral(PA(10), PERIPH_A, 0); /* CLK */ select_peripheral(PA(11), PERIPH_A, 0); /* CMD */ @@ -1300,12 +1313,19 @@ struct platform_device *__init at32_add_device_mci(unsigned int id) select_peripheral(PA(14), PERIPH_A, 0); /* DATA2 */ select_peripheral(PA(15), PERIPH_A, 0); /* DATA3 */ + if (data) { + if (data->detect_pin != GPIO_PIN_NONE) + at32_select_gpio(data->detect_pin, 0); + if (data->wp_pin != GPIO_PIN_NONE) + at32_select_gpio(data->wp_pin, 0); + } + atmel_mci0_pclk.dev = &pdev->dev; platform_device_add(pdev); return pdev; -err_add_resources: +fail: platform_device_put(pdev); return NULL; } diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index dc88c03..198df42 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -104,6 +104,16 @@ config MMC_AT91 If unsure, say N. +config MMC_ATMELMCI + tristate "Atmel Multimedia Card Interface support" + depends on AVR32 + help + This selects the Atmel Multimedia Card Interface driver. If + you have an AT32 (AVR32) platform with a Multimedia Card + slot, say Y or M here. + + If unsure, say N. + config MMC_IMX tristate "Motorola i.MX Multimedia Card Interface support" depends on ARCH_IMX diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index b3e023b..2dc9ff2 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -16,6 +16,7 @@ obj-$(CONFIG_MMC_WBSD) += wbsd.o obj-$(CONFIG_MMC_AU1X) += au1xmmc.o obj-$(CONFIG_MMC_OMAP) += omap.o obj-$(CONFIG_MMC_AT91) += at91_mci.o +obj-$(CONFIG_MMC_ATMELMCI) += atmel-mci.o obj-$(CONFIG_MMC_TIFM_SD) += tifm_sd.o obj-$(CONFIG_MMC_SPI) += mmc_spi.o obj-$(CONFIG_MMC_S3C) += s3cmci.o diff --git a/drivers/mmc/host/atmel-mci-regs.h b/drivers/mmc/host/atmel-mci-regs.h new file mode 100644 index 0000000..a9a5657 --- /dev/null +++ b/drivers/mmc/host/atmel-mci-regs.h @@ -0,0 +1,91 @@ +/* + * Atmel MultiMedia Card Interface driver + * + * Copyright (C) 2004-2006 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __DRIVERS_MMC_ATMEL_MCI_H__ +#define __DRIVERS_MMC_ATMEL_MCI_H__ + +/* MCI Register Definitions */ +#define MCI_CR 0x0000 /* Control */ +# define MCI_CR_MCIEN ( 1 << 0) /* MCI Enable */ +# define MCI_CR_MCIDIS ( 1 << 1) /* MCI Disable */ +# define MCI_CR_SWRST ( 1 << 7) /* Software Reset */ +#define MCI_MR 0x0004 /* Mode */ +# define MCI_MR_CLKDIV(x) ((x) << 0) /* Clock Divider */ +# define MCI_MR_RDPROOF ( 1 << 11) /* Read Proof */ +# define MCI_MR_WRPROOF ( 1 << 12) /* Write Proof */ +#define MCI_DTOR 0x0008 /* Data Timeout */ +# define MCI_DTOCYC(x) ((x) << 0) /* Data Timeout Cycles */ +# define MCI_DTOMUL(x) ((x) << 4) /* Data Timeout Multiplier */ +#define MCI_SDCR 0x000c /* SD Card / SDIO */ +# define MCI_SDCSEL_SLOT_A ( 0 << 0) /* Select SD slot A */ +# define MCI_SDCSEL_SLOT_B ( 1 << 0) /* Select SD slot A */ +# define MCI_SDCBUS_1BIT ( 0 << 7) /* 1-bit data bus */ +# define MCI_SDCBUS_4BIT ( 1 << 7) /* 4-bit data bus */ +#define MCI_ARGR 0x0010 /* Command Argument */ +#define MCI_CMDR 0x0014 /* Command */ +# define MCI_CMDR_CMDNB(x) ((x) << 0) /* Command Opcode */ +# define MCI_CMDR_RSPTYP_NONE ( 0 << 6) /* No response */ +# define MCI_CMDR_RSPTYP_48BIT ( 1 << 6) /* 48-bit response */ +# define MCI_CMDR_RSPTYP_136BIT ( 2 << 6) /* 136-bit response */ +# define MCI_CMDR_SPCMD_INIT ( 1 << 8) /* Initialization command */ +# define MCI_CMDR_SPCMD_SYNC ( 2 << 8) /* Synchronized command */ +# define MCI_CMDR_SPCMD_INT ( 4 << 8) /* Interrupt command */ +# define MCI_CMDR_SPCMD_INTRESP ( 5 << 8) /* Interrupt response */ +# define MCI_CMDR_OPDCMD ( 1 << 11) /* Open Drain */ +# define MCI_CMDR_MAXLAT_5CYC ( 0 << 12) /* Max latency 5 cycles */ +# define MCI_CMDR_MAXLAT_64CYC ( 1 << 12) /* Max latency 64 cycles */ +# define MCI_CMDR_START_XFER ( 1 << 16) /* Start data transfer */ +# define MCI_CMDR_STOP_XFER ( 2 << 16) /* Stop data transfer */ +# define MCI_CMDR_TRDIR_WRITE ( 0 << 18) /* Write data */ +# define MCI_CMDR_TRDIR_READ ( 1 << 18) /* Read data */ +# define MCI_CMDR_BLOCK ( 0 << 19) /* Single-block transfer */ +# define MCI_CMDR_MULTI_BLOCK ( 1 << 19) /* Multi-block transfer */ +# define MCI_CMDR_STREAM ( 2 << 19) /* MMC Stream transfer */ +# define MCI_CMDR_SDIO_BYTE ( 4 << 19) /* SDIO Byte transfer */ +# define MCI_CMDR_SDIO_BLOCK ( 5 << 19) /* SDIO Block transfer */ +# define MCI_CMDR_SDIO_SUSPEND ( 1 << 24) /* SDIO Suspend Command */ +# define MCI_CMDR_SDIO_RESUME ( 2 << 24) /* SDIO Resume Command */ +#define MCI_BLKR 0x0018 /* Block */ +# define MCI_BCNT(x) ((x) << 0) /* Data Block Count */ +# define MCI_BLKLEN(x) ((x) << 16) /* Data Block Length */ +#define MCI_RSPR 0x0020 /* Response 0 */ +#define MCI_RSPR1 0x0024 /* Response 1 */ +#define MCI_RSPR2 0x0028 /* Response 2 */ +#define MCI_RSPR3 0x002c /* Response 3 */ +#define MCI_RDR 0x0030 /* Receive Data */ +#define MCI_TDR 0x0034 /* Transmit Data */ +#define MCI_SR 0x0040 /* Status */ +#define MCI_IER 0x0044 /* Interrupt Enable */ +#define MCI_IDR 0x0048 /* Interrupt Disable */ +#define MCI_IMR 0x004c /* Interrupt Mask */ +# define MCI_CMDRDY ( 1 << 0) /* Command Ready */ +# define MCI_RXRDY ( 1 << 1) /* Receiver Ready */ +# define MCI_TXRDY ( 1 << 2) /* Transmitter Ready */ +# define MCI_BLKE ( 1 << 3) /* Data Block Ended */ +# define MCI_DTIP ( 1 << 4) /* Data Transfer In Progress */ +# define MCI_NOTBUSY ( 1 << 5) /* Data Not Busy */ +# define MCI_SDIOIRQA ( 1 << 8) /* SDIO IRQ in slot A */ +# define MCI_SDIOIRQB ( 1 << 9) /* SDIO IRQ in slot B */ +# define MCI_RINDE ( 1 << 16) /* Response Index Error */ +# define MCI_RDIRE ( 1 << 17) /* Response Direction Error */ +# define MCI_RCRCE ( 1 << 18) /* Response CRC Error */ +# define MCI_RENDE ( 1 << 19) /* Response End Bit Error */ +# define MCI_RTOE ( 1 << 20) /* Response Time-Out Error */ +# define MCI_DCRCE ( 1 << 21) /* Data CRC Error */ +# define MCI_DTOE ( 1 << 22) /* Data Time-Out Error */ +# define MCI_OVRE ( 1 << 30) /* RX Overrun Error */ +# define MCI_UNRE ( 1 << 31) /* TX Underrun Error */ + +/* Register access macros */ +#define mci_readl(port,reg) \ + __raw_readl((port)->regs + MCI_##reg) +#define mci_writel(port,reg,value) \ + __raw_writel((value), (port)->regs + MCI_##reg) + +#endif /* __DRIVERS_MMC_ATMEL_MCI_H__ */ diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c new file mode 100644 index 0000000..25d5324a --- /dev/null +++ b/drivers/mmc/host/atmel-mci.c @@ -0,0 +1,981 @@ +/* + * Atmel MultiMedia Card Interface driver + * + * Copyright (C) 2004-2008 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include +#include + +#include +#include + +#include "atmel-mci-regs.h" + +#define ATMCI_DATA_ERROR_FLAGS (MCI_DCRCE | MCI_DTOE | MCI_OVRE | MCI_UNRE) + +enum { + EVENT_CMD_COMPLETE = 0, + EVENT_DATA_ERROR, + EVENT_DATA_COMPLETE, + EVENT_STOP_SENT, + EVENT_STOP_COMPLETE, + EVENT_XFER_COMPLETE, +}; + +struct atmel_mci { + struct mmc_host *mmc; + void __iomem *regs; + + struct scatterlist *sg; + unsigned int pio_offset; + + struct mmc_request *mrq; + struct mmc_command *cmd; + struct mmc_data *data; + + u32 cmd_status; + u32 data_status; + u32 stop_status; + u32 stop_cmdr; + + u32 mode_reg; + u32 sdc_reg; + + struct tasklet_struct tasklet; + unsigned long pending_events; + unsigned long completed_events; + + int present; + int detect_pin; + int wp_pin; + + /* For detect pin debouncing */ + struct timer_list detect_timer; + + unsigned long bus_hz; + unsigned long mapbase; + struct clk *mck; + struct platform_device *pdev; +}; + +#define atmci_is_completed(host, event) \ + test_bit(event, &host->completed_events) +#define atmci_test_and_clear_pending(host, event) \ + test_and_clear_bit(event, &host->pending_events) +#define atmci_test_and_set_completed(host, event) \ + test_and_set_bit(event, &host->completed_events) +#define atmci_set_completed(host, event) \ + set_bit(event, &host->completed_events) +#define atmci_set_pending(host, event) \ + set_bit(event, &host->pending_events) +#define atmci_clear_pending(host, event) \ + clear_bit(event, &host->pending_events) + + +static void atmci_enable(struct atmel_mci *host) +{ + clk_enable(host->mck); + mci_writel(host, CR, MCI_CR_MCIEN); + mci_writel(host, MR, host->mode_reg); + mci_writel(host, SDCR, host->sdc_reg); +} + +static void atmci_disable(struct atmel_mci *host) +{ + mci_writel(host, CR, MCI_CR_SWRST); + + /* Stall until write is complete, then disable the bus clock */ + mci_readl(host, SR); + clk_disable(host->mck); +} + +static inline unsigned int ns_to_clocks(struct atmel_mci *host, + unsigned int ns) +{ + return (ns * (host->bus_hz / 1000000) + 999) / 1000; +} + +static void atmci_set_timeout(struct atmel_mci *host, + struct mmc_data *data) +{ + static unsigned dtomul_to_shift[] = { + 0, 4, 7, 8, 10, 12, 16, 20 + }; + unsigned timeout; + unsigned dtocyc; + unsigned dtomul; + + timeout = ns_to_clocks(host, data->timeout_ns) + data->timeout_clks; + + for (dtomul = 0; dtomul < 8; dtomul++) { + unsigned shift = dtomul_to_shift[dtomul]; + dtocyc = (timeout + (1 << shift) - 1) >> shift; + if (dtocyc < 15) + break; + } + + if (dtomul >= 8) { + dtomul = 7; + dtocyc = 15; + } + + dev_vdbg(&host->mmc->class_dev, "setting timeout to %u cycles\n", + dtocyc << dtomul_to_shift[dtomul]); + mci_writel(host, DTOR, (MCI_DTOMUL(dtomul) | MCI_DTOCYC(dtocyc))); +} + +/* + * Return mask with command flags to be enabled for this command. + */ +static u32 atmci_prepare_command(struct mmc_host *mmc, + struct mmc_command *cmd) +{ + struct mmc_data *data; + u32 cmdr; + + cmd->error = -EINPROGRESS; + + cmdr = MCI_CMDR_CMDNB(cmd->opcode); + + if (cmd->flags & MMC_RSP_PRESENT) { + if (cmd->flags & MMC_RSP_136) + cmdr |= MCI_CMDR_RSPTYP_136BIT; + else + cmdr |= MCI_CMDR_RSPTYP_48BIT; + } + + /* + * This should really be MAXLAT_5 for CMD2 and ACMD41, but + * it's too difficult to determine whether this is an ACMD or + * not. Better make it 64. + */ + cmdr |= MCI_CMDR_MAXLAT_64CYC; + + if (mmc->ios.bus_mode == MMC_BUSMODE_OPENDRAIN) + cmdr |= MCI_CMDR_OPDCMD; + + data = cmd->data; + if (data) { + cmdr |= MCI_CMDR_START_XFER; + if (data->flags & MMC_DATA_STREAM) + cmdr |= MCI_CMDR_STREAM; + else if (data->blocks > 1) + cmdr |= MCI_CMDR_MULTI_BLOCK; + else + cmdr |= MCI_CMDR_BLOCK; + + if (data->flags & MMC_DATA_READ) + cmdr |= MCI_CMDR_TRDIR_READ; + } + + return cmdr; +} + +static void atmci_start_command(struct atmel_mci *host, + struct mmc_command *cmd, + u32 cmd_flags) +{ + /* Must read host->cmd after testing event flags */ + smp_rmb(); + WARN_ON(host->cmd); + host->cmd = cmd; + + dev_vdbg(&host->mmc->class_dev, + "start command: ARGR=0x%08x CMDR=0x%08x\n", + cmd->arg, cmd_flags); + + mci_writel(host, ARGR, cmd->arg); + mci_writel(host, CMDR, cmd_flags); +} + +static void send_stop_cmd(struct mmc_host *mmc, struct mmc_data *data) +{ + struct atmel_mci *host = mmc_priv(mmc); + + atmci_start_command(host, data->stop, host->stop_cmdr); + mci_writel(host, IER, MCI_CMDRDY); +} + +static void atmci_request_end(struct mmc_host *mmc, struct mmc_request *mrq) +{ + struct atmel_mci *host = mmc_priv(mmc); + + WARN_ON(host->cmd || host->data); + host->mrq = NULL; + + atmci_disable(host); + + mmc_request_done(mmc, mrq); +} + +/* + * Returns a mask of interrupt flags to be enabled after the whole + * request has been prepared. + */ +static u32 atmci_submit_data(struct mmc_host *mmc, struct mmc_data *data) +{ + struct atmel_mci *host = mmc_priv(mmc); + u32 iflags; + + data->error = -EINPROGRESS; + + WARN_ON(host->data); + host->sg = NULL; + host->data = data; + + mci_writel(host, BLKR, MCI_BCNT(data->blocks) + | MCI_BLKLEN(data->blksz)); + dev_vdbg(&mmc->class_dev, "BLKR=0x%08x\n", + MCI_BCNT(data->blocks) | MCI_BLKLEN(data->blksz)); + + iflags = ATMCI_DATA_ERROR_FLAGS; + host->sg = data->sg; + host->pio_offset = 0; + if (data->flags & MMC_DATA_READ) + iflags |= MCI_RXRDY; + else + iflags |= MCI_TXRDY; + + return iflags; +} + +static void atmci_request(struct mmc_host *mmc, struct mmc_request *mrq) +{ + struct atmel_mci *host = mmc_priv(mmc); + struct mmc_data *data; + struct mmc_command *cmd; + u32 iflags; + u32 cmdflags = 0; + + iflags = mci_readl(host, IMR); + if (iflags) + dev_warn(&mmc->class_dev, "WARNING: IMR=0x%08x\n", + mci_readl(host, IMR)); + + WARN_ON(host->mrq != NULL); + + /* + * We may "know" the card is gone even though there's still an + * electrical connection. If so, we really need to communicate + * this to the MMC core since there won't be any more + * interrupts as the card is completely removed. Otherwise, + * the MMC core might believe the card is still there even + * though the card was just removed very slowly. + */ + if (!host->present) { + mrq->cmd->error = -ENOMEDIUM; + mmc_request_done(mmc, mrq); + return; + } + + host->mrq = mrq; + host->pending_events = 0; + host->completed_events = 0; + + atmci_enable(host); + + /* We don't support multiple blocks of weird lengths. */ + data = mrq->data; + if (data) { + if (data->blocks > 1 && data->blksz & 3) + goto fail; + atmci_set_timeout(host, data); + } + + iflags = MCI_CMDRDY; + cmd = mrq->cmd; + cmdflags = atmci_prepare_command(mmc, cmd); + atmci_start_command(host, cmd, cmdflags); + + if (data) + iflags |= atmci_submit_data(mmc, data); + + if (mrq->stop) { + host->stop_cmdr = atmci_prepare_command(mmc, mrq->stop); + host->stop_cmdr |= MCI_CMDR_STOP_XFER; + if (!(data->flags & MMC_DATA_WRITE)) + host->stop_cmdr |= MCI_CMDR_TRDIR_READ; + if (data->flags & MMC_DATA_STREAM) + host->stop_cmdr |= MCI_CMDR_STREAM; + else + host->stop_cmdr |= MCI_CMDR_MULTI_BLOCK; + } + + /* + * We could have enabled interrupts earlier, but I suspect + * that would open up a nice can of interesting race + * conditions (e.g. command and data complete, but stop not + * prepared yet.) + */ + mci_writel(host, IER, iflags); + + return; + +fail: + atmci_disable(host); + host->mrq = NULL; + mrq->cmd->error = -EINVAL; + mmc_request_done(mmc, mrq); +} + +static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct atmel_mci *host = mmc_priv(mmc); + + if (ios->clock) { + u32 clkdiv; + + /* Set clock rate */ + clkdiv = DIV_ROUND_UP(host->bus_hz, 2 * ios->clock) - 1; + if (clkdiv > 255) { + dev_warn(&mmc->class_dev, + "clock %u too slow; using %lu\n", + ios->clock, host->bus_hz / (2 * 256)); + clkdiv = 255; + } + + host->mode_reg = MCI_MR_CLKDIV(clkdiv) | MCI_MR_WRPROOF + | MCI_MR_RDPROOF; + } + + switch (ios->bus_width) { + case MMC_BUS_WIDTH_1: + host->sdc_reg = 0; + break; + case MMC_BUS_WIDTH_4: + host->sdc_reg = MCI_SDCBUS_4BIT; + break; + } + + switch (ios->power_mode) { + case MMC_POWER_ON: + /* Send init sequence (74 clock cycles) */ + atmci_enable(host); + mci_writel(host, CMDR, MCI_CMDR_SPCMD_INIT); + while (!(mci_readl(host, SR) & MCI_CMDRDY)) + cpu_relax(); + atmci_disable(host); + break; + default: + /* + * TODO: None of the currently available AVR32-based + * boards allow MMC power to be turned off. Implement + * power control when this can be tested properly. + */ + break; + } +} + +static int atmci_get_ro(struct mmc_host *mmc) +{ + int read_only = 0; + struct atmel_mci *host = mmc_priv(mmc); + + if (host->wp_pin >= 0) { + read_only = gpio_get_value(host->wp_pin); + dev_dbg(&mmc->class_dev, "card is %s\n", + read_only ? "read-only" : "read-write"); + } else { + dev_dbg(&mmc->class_dev, + "no pin for checking read-only switch." + " Assuming write-enable.\n"); + } + + return read_only; +} + +static struct mmc_host_ops atmci_ops = { + .request = atmci_request, + .set_ios = atmci_set_ios, + .get_ro = atmci_get_ro, +}; + +static void atmci_command_complete(struct atmel_mci *host, + struct mmc_command *cmd, u32 status) +{ + /* Read the response from the card (up to 16 bytes) */ + cmd->resp[0] = mci_readl(host, RSPR); + cmd->resp[1] = mci_readl(host, RSPR); + cmd->resp[2] = mci_readl(host, RSPR); + cmd->resp[3] = mci_readl(host, RSPR); + + if (status & MCI_RTOE) + cmd->error = -ETIMEDOUT; + else if ((cmd->flags & MMC_RSP_CRC) && (status & MCI_RCRCE)) + cmd->error = -EILSEQ; + else if (status & (MCI_RINDE | MCI_RDIRE | MCI_RENDE)) + cmd->error = -EIO; + else + cmd->error = 0; + + if (cmd->error) { + dev_dbg(&host->mmc->class_dev, + "command error: status=0x%08x\n", status); + + if (cmd->data) { + host->data = NULL; + mci_writel(host, IDR, MCI_NOTBUSY + | MCI_TXRDY | MCI_RXRDY + | ATMCI_DATA_ERROR_FLAGS); + } + } +} + +static void atmci_detect_change(unsigned long data) +{ + struct atmel_mci *host = (struct atmel_mci *)data; + struct mmc_request *mrq = host->mrq; + int present; + + /* + * atmci_remove() sets detect_pin to -1 before freeing the + * interrupt. We must not re-enable the interrupt if it has + * been freed. + */ + smp_rmb(); + if (host->detect_pin < 0) + return; + + enable_irq(gpio_to_irq(host->detect_pin)); + present = !gpio_get_value(host->detect_pin); + + dev_vdbg(&host->pdev->dev, "detect change: %d (was %d)\n", + present, host->present); + + if (present != host->present) { + dev_dbg(&host->mmc->class_dev, "card %s\n", + present ? "inserted" : "removed"); + host->present = present; + + /* Reset controller if card is gone */ + if (!present) { + mci_writel(host, CR, MCI_CR_SWRST); + mci_writel(host, IDR, ~0UL); + mci_writel(host, CR, MCI_CR_MCIEN); + } + + /* Clean up queue if present */ + if (mrq) { + /* + * Reset controller to terminate any ongoing + * commands or data transfers. + */ + mci_writel(host, CR, MCI_CR_SWRST); + + if (!atmci_is_completed(host, EVENT_CMD_COMPLETE)) + mrq->cmd->error = -ENOMEDIUM; + + if (mrq->data && !atmci_is_completed(host, + EVENT_DATA_COMPLETE)) { + host->data = NULL; + mrq->data->error = -ENOMEDIUM; + } + if (mrq->stop && !atmci_is_completed(host, + EVENT_STOP_COMPLETE)) + mrq->stop->error = -ENOMEDIUM; + + host->cmd = NULL; + atmci_request_end(host->mmc, mrq); + } + + mmc_detect_change(host->mmc, 0); + } +} + +static void atmci_tasklet_func(unsigned long priv) +{ + struct mmc_host *mmc = (struct mmc_host *)priv; + struct atmel_mci *host = mmc_priv(mmc); + struct mmc_request *mrq = host->mrq; + struct mmc_data *data = host->data; + + dev_vdbg(&mmc->class_dev, + "tasklet: pending/completed/mask %lx/%lx/%x\n", + host->pending_events, host->completed_events, + mci_readl(host, IMR)); + + if (atmci_test_and_clear_pending(host, EVENT_CMD_COMPLETE)) { + /* + * host->cmd must be set to NULL before the interrupt + * handler sees EVENT_CMD_COMPLETE + */ + host->cmd = NULL; + smp_wmb(); + atmci_set_completed(host, EVENT_CMD_COMPLETE); + atmci_command_complete(host, mrq->cmd, host->cmd_status); + + if (!mrq->cmd->error && mrq->stop + && atmci_is_completed(host, EVENT_XFER_COMPLETE) + && !atmci_test_and_set_completed(host, + EVENT_STOP_SENT)) + send_stop_cmd(host->mmc, mrq->data); + } + if (atmci_test_and_clear_pending(host, EVENT_STOP_COMPLETE)) { + /* + * host->cmd must be set to NULL before the interrupt + * handler sees EVENT_STOP_COMPLETE + */ + host->cmd = NULL; + smp_wmb(); + atmci_set_completed(host, EVENT_STOP_COMPLETE); + atmci_command_complete(host, mrq->stop, host->stop_status); + } + if (atmci_test_and_clear_pending(host, EVENT_DATA_ERROR)) { + u32 status = host->data_status; + + dev_vdbg(&mmc->class_dev, "data error: status=%08x\n", status); + + atmci_set_completed(host, EVENT_DATA_ERROR); + atmci_set_completed(host, EVENT_DATA_COMPLETE); + + if (status & MCI_DTOE) { + dev_dbg(&mmc->class_dev, + "data timeout error\n"); + data->error = -ETIMEDOUT; + } else if (status & MCI_DCRCE) { + dev_dbg(&mmc->class_dev, "data CRC error\n"); + data->error = -EILSEQ; + } else { + dev_dbg(&mmc->class_dev, + "data FIFO error (status=%08x)\n", + status); + data->error = -EIO; + } + + if (host->present && data->stop + && atmci_is_completed(host, EVENT_CMD_COMPLETE) + && !atmci_test_and_set_completed( + host, EVENT_STOP_SENT)) + send_stop_cmd(host->mmc, data); + + host->data = NULL; + } + if (atmci_test_and_clear_pending(host, EVENT_DATA_COMPLETE)) { + atmci_set_completed(host, EVENT_DATA_COMPLETE); + + if (!atmci_is_completed(host, EVENT_DATA_ERROR)) { + data->bytes_xfered = data->blocks * data->blksz; + data->error = 0; + } + + host->data = NULL; + } + + if (host->mrq && !host->cmd && !host->data) + atmci_request_end(mmc, host->mrq); +} + +static void atmci_read_data_pio(struct atmel_mci *host) +{ + struct scatterlist *sg = host->sg; + void *buf = sg_virt(sg); + unsigned int offset = host->pio_offset; + struct mmc_data *data = host->data; + u32 value; + u32 status; + unsigned int nbytes = 0; + + do { + value = mci_readl(host, RDR); + if (likely(offset + 4 <= sg->length)) { + put_unaligned(value, (u32 *)(buf + offset)); + + offset += 4; + nbytes += 4; + + if (offset == sg->length) { + host->sg = sg = sg_next(sg); + if (!sg) + goto done; + + offset = 0; + buf = sg_virt(sg); + } + } else { + unsigned int remaining = sg->length - offset; + memcpy(buf + offset, &value, remaining); + nbytes += remaining; + + flush_dcache_page(sg_page(sg)); + host->sg = sg = sg_next(sg); + if (!sg) + goto done; + + offset = 4 - remaining; + buf = sg_virt(sg); + memcpy(buf, (u8 *)&value + remaining, offset); + nbytes += offset; + } + + status = mci_readl(host, SR); + if (status & ATMCI_DATA_ERROR_FLAGS) { + mci_writel(host, IDR, (MCI_NOTBUSY | MCI_RXRDY + | ATMCI_DATA_ERROR_FLAGS)); + host->data_status = status; + atmci_set_pending(host, EVENT_DATA_ERROR); + tasklet_schedule(&host->tasklet); + break; + } + } while (status & MCI_RXRDY); + + host->pio_offset = offset; + data->bytes_xfered += nbytes; + + return; + +done: + mci_writel(host, IDR, MCI_RXRDY); + mci_writel(host, IER, MCI_NOTBUSY); + data->bytes_xfered += nbytes; + atmci_set_completed(host, EVENT_XFER_COMPLETE); + if (data->stop && atmci_is_completed(host, EVENT_CMD_COMPLETE) + && !atmci_test_and_set_completed(host, EVENT_STOP_SENT)) + send_stop_cmd(host->mmc, data); +} + +static void atmci_write_data_pio(struct atmel_mci *host) +{ + struct scatterlist *sg = host->sg; + void *buf = sg_virt(sg); + unsigned int offset = host->pio_offset; + struct mmc_data *data = host->data; + u32 value; + u32 status; + unsigned int nbytes = 0; + + do { + if (likely(offset + 4 <= sg->length)) { + value = get_unaligned((u32 *)(buf + offset)); + mci_writel(host, TDR, value); + + offset += 4; + nbytes += 4; + if (offset == sg->length) { + host->sg = sg = sg_next(sg); + if (!sg) + goto done; + + offset = 0; + buf = sg_virt(sg); + } + } else { + unsigned int remaining = sg->length - offset; + + value = 0; + memcpy(&value, buf + offset, remaining); + nbytes += remaining; + + host->sg = sg = sg_next(sg); + if (!sg) { + mci_writel(host, TDR, value); + goto done; + } + + offset = 4 - remaining; + buf = sg_virt(sg); + memcpy((u8 *)&value + remaining, buf, offset); + mci_writel(host, TDR, value); + nbytes += offset; + } + + status = mci_readl(host, SR); + if (status & ATMCI_DATA_ERROR_FLAGS) { + mci_writel(host, IDR, (MCI_NOTBUSY | MCI_TXRDY + | ATMCI_DATA_ERROR_FLAGS)); + host->data_status = status; + atmci_set_pending(host, EVENT_DATA_ERROR); + tasklet_schedule(&host->tasklet); + break; + } + } while (status & MCI_TXRDY); + + host->pio_offset = offset; + data->bytes_xfered += nbytes; + + return; + +done: + mci_writel(host, IDR, MCI_TXRDY); + mci_writel(host, IER, MCI_NOTBUSY); + data->bytes_xfered += nbytes; + atmci_set_completed(host, EVENT_XFER_COMPLETE); + if (data->stop && atmci_is_completed(host, EVENT_CMD_COMPLETE) + && !atmci_test_and_set_completed(host, EVENT_STOP_SENT)) + send_stop_cmd(host->mmc, data); +} + +static void atmci_cmd_interrupt(struct mmc_host *mmc, u32 status) +{ + struct atmel_mci *host = mmc_priv(mmc); + + mci_writel(host, IDR, MCI_CMDRDY); + + if (atmci_is_completed(host, EVENT_STOP_SENT)) { + host->stop_status = status; + atmci_set_pending(host, EVENT_STOP_COMPLETE); + } else { + host->cmd_status = status; + atmci_set_pending(host, EVENT_CMD_COMPLETE); + } + + tasklet_schedule(&host->tasklet); +} + +static irqreturn_t atmci_interrupt(int irq, void *dev_id) +{ + struct mmc_host *mmc = dev_id; + struct atmel_mci *host = mmc_priv(mmc); + u32 status, mask, pending; + unsigned int pass_count = 0; + + spin_lock(&mmc->lock); + + do { + status = mci_readl(host, SR); + mask = mci_readl(host, IMR); + pending = status & mask; + if (!pending) + break; + + if (pending & ATMCI_DATA_ERROR_FLAGS) { + mci_writel(host, IDR, ATMCI_DATA_ERROR_FLAGS + | MCI_RXRDY | MCI_TXRDY); + pending &= mci_readl(host, IMR); + host->data_status = status; + atmci_set_pending(host, EVENT_DATA_ERROR); + tasklet_schedule(&host->tasklet); + } + if (pending & MCI_NOTBUSY) { + mci_writel(host, IDR, (MCI_NOTBUSY + | ATMCI_DATA_ERROR_FLAGS)); + atmci_set_pending(host, EVENT_DATA_COMPLETE); + tasklet_schedule(&host->tasklet); + } + if (pending & MCI_RXRDY) + atmci_read_data_pio(host); + if (pending & MCI_TXRDY) + atmci_write_data_pio(host); + + if (pending & MCI_CMDRDY) + atmci_cmd_interrupt(mmc, status); + } while (pass_count++ < 5); + + spin_unlock(&mmc->lock); + + return pass_count ? IRQ_HANDLED : IRQ_NONE; +} + +static irqreturn_t atmci_detect_interrupt(int irq, void *dev_id) +{ + struct mmc_host *mmc = dev_id; + struct atmel_mci *host = mmc_priv(mmc); + + /* + * Disable interrupts until the pin has stabilized and check + * the state then. Use mod_timer() since we may be in the + * middle of the timer routine when this interrupt triggers. + */ + disable_irq_nosync(irq); + mod_timer(&host->detect_timer, jiffies + msecs_to_jiffies(20)); + + return IRQ_HANDLED; +} + +static int __init atmci_probe(struct platform_device *pdev) +{ + struct mci_platform_data *pdata; + struct atmel_mci *host; + struct mmc_host *mmc; + struct resource *regs; + int irq; + int ret; + + regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!regs) + return -ENXIO; + pdata = pdev->dev.platform_data; + if (!pdata) + return -ENXIO; + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + mmc = mmc_alloc_host(sizeof(struct atmel_mci), &pdev->dev); + if (!mmc) + return -ENOMEM; + + host = mmc_priv(mmc); + host->pdev = pdev; + host->mmc = mmc; + host->detect_pin = pdata->detect_pin; + host->wp_pin = pdata->wp_pin; + + host->mck = clk_get(&pdev->dev, "mci_clk"); + if (IS_ERR(host->mck)) { + ret = PTR_ERR(host->mck); + goto err_clk_get; + } + + ret = -ENOMEM; + host->regs = ioremap(regs->start, regs->end - regs->start + 1); + if (!host->regs) + goto err_ioremap; + + clk_enable(host->mck); + mci_writel(host, CR, MCI_CR_SWRST); + host->bus_hz = clk_get_rate(host->mck); + clk_disable(host->mck); + + host->mapbase = regs->start; + + mmc->ops = &atmci_ops; + mmc->f_min = (host->bus_hz + 511) / 512; + mmc->f_max = host->bus_hz / 2; + mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; + mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE; + + mmc->max_hw_segs = 64; + mmc->max_phys_segs = 64; + mmc->max_req_size = 32768 * 512; + mmc->max_blk_size = 32768; + mmc->max_blk_count = 512; + + tasklet_init(&host->tasklet, atmci_tasklet_func, (unsigned long)mmc); + + ret = request_irq(irq, atmci_interrupt, 0, pdev->dev.bus_id, mmc); + if (ret) + goto err_request_irq; + + /* Assume card is present if we don't have a detect pin */ + host->present = 1; + if (host->detect_pin >= 0) { + if (gpio_request(host->detect_pin, "mmc_detect")) { + dev_dbg(&mmc->class_dev, "no detect pin available\n"); + host->detect_pin = -1; + } else { + host->present = !gpio_get_value(host->detect_pin); + } + } + if (host->wp_pin >= 0) { + if (gpio_request(host->wp_pin, "mmc_wp")) { + dev_dbg(&mmc->class_dev, "no WP pin available\n"); + host->wp_pin = -1; + } + } + + platform_set_drvdata(pdev, host); + + mmc_add_host(mmc); + + if (host->detect_pin >= 0) { + setup_timer(&host->detect_timer, atmci_detect_change, + (unsigned long)host); + + ret = request_irq(gpio_to_irq(host->detect_pin), + atmci_detect_interrupt, + IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, + "mmc-detect", mmc); + if (ret) { + dev_dbg(&mmc->class_dev, + "could not request IRQ %d for detect pin\n", + gpio_to_irq(host->detect_pin)); + gpio_free(host->detect_pin); + host->detect_pin = -1; + } + } + + dev_info(&mmc->class_dev, + "Atmel MCI controller at 0x%08lx irq %d\n", + host->mapbase, irq); + + return 0; + +err_request_irq: + iounmap(host->regs); +err_ioremap: + clk_put(host->mck); +err_clk_get: + mmc_free_host(mmc); + return ret; +} + +static int __exit atmci_remove(struct platform_device *pdev) +{ + struct atmel_mci *host = platform_get_drvdata(pdev); + + platform_set_drvdata(pdev, NULL); + + if (host) { + if (host->detect_pin >= 0) { + int pin = host->detect_pin; + + /* Make sure the timer doesn't enable the interrupt */ + host->detect_pin = -1; + smp_wmb(); + + free_irq(gpio_to_irq(pin), host->mmc); + del_timer_sync(&host->detect_timer); + gpio_free(pin); + } + + mmc_remove_host(host->mmc); + + clk_enable(host->mck); + mci_writel(host, IDR, ~0UL); + mci_writel(host, CR, MCI_CR_MCIDIS); + mci_readl(host, SR); + clk_disable(host->mck); + + if (host->wp_pin >= 0) + gpio_free(host->wp_pin); + + free_irq(platform_get_irq(pdev, 0), host->mmc); + iounmap(host->regs); + + clk_put(host->mck); + + mmc_free_host(host->mmc); + } + return 0; +} + +static struct platform_driver atmci_driver = { + .remove = __exit_p(atmci_remove), + .driver = { + .name = "atmel_mci", + }, +}; + +static int __init atmci_init(void) +{ + return platform_driver_probe(&atmci_driver, atmci_probe); +} + +static void __exit atmci_exit(void) +{ + platform_driver_unregister(&atmci_driver); +} + +module_init(atmci_init); +module_exit(atmci_exit); + +MODULE_DESCRIPTION("Atmel Multimedia Card Interface driver"); +MODULE_AUTHOR("Haavard Skinnemoen "); +MODULE_LICENSE("GPL v2"); diff --git a/include/asm-avr32/arch-at32ap/board.h b/include/asm-avr32/arch-at32ap/board.h index b4cddfa..a378386 100644 --- a/include/asm-avr32/arch-at32ap/board.h +++ b/include/asm-avr32/arch-at32ap/board.h @@ -77,7 +77,11 @@ struct i2c_board_info; struct platform_device *at32_add_device_twi(unsigned int id, struct i2c_board_info *b, unsigned int n); -struct platform_device *at32_add_device_mci(unsigned int id); + +struct mci_platform_data; +struct platform_device * +at32_add_device_mci(unsigned int id, struct mci_platform_data *data); + struct platform_device *at32_add_device_ac97c(unsigned int id); struct platform_device *at32_add_device_abdac(unsigned int id); struct platform_device *at32_add_device_psif(unsigned int id); diff --git a/include/asm-avr32/atmel-mci.h b/include/asm-avr32/atmel-mci.h new file mode 100644 index 0000000..c2ea6e1 --- /dev/null +++ b/include/asm-avr32/atmel-mci.h @@ -0,0 +1,9 @@ +#ifndef __ASM_AVR32_ATMEL_MCI_H +#define __ASM_AVR32_ATMEL_MCI_H + +struct mci_platform_data { + int detect_pin; + int wp_pin; +}; + +#endif /* __ASM_AVR32_ATMEL_MCI_H */ -- cgit v1.1 From 97067d5581ec831a75a45a52e417bee0f7943dbf Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sun, 6 Jul 2008 00:51:07 +0200 Subject: wbsd: fix bad dma_addr_t conversion DMA addresses are not pointers, so don't treat them as such. Avoids compiler warnings when using 64-bit DMA addresses on a 32-bit system. Signed-off-by: Pierre Ossman --- drivers/mmc/host/wbsd.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/host/wbsd.c b/drivers/mmc/host/wbsd.c index c2b6160..f7dcd8e 100644 --- a/drivers/mmc/host/wbsd.c +++ b/drivers/mmc/host/wbsd.c @@ -1420,7 +1420,7 @@ kfree: dma_unmap_single(mmc_dev(host->mmc), host->dma_addr, WBSD_DMA_SIZE, DMA_BIDIRECTIONAL); - host->dma_addr = (dma_addr_t)NULL; + host->dma_addr = 0; kfree(host->dma_buffer); host->dma_buffer = NULL; @@ -1445,7 +1445,7 @@ static void wbsd_release_dma(struct wbsd_host *host) host->dma = -1; host->dma_buffer = NULL; - host->dma_addr = (dma_addr_t)NULL; + host->dma_addr = 0; } /* -- cgit v1.1 From 23af60398af2f5033e2f53665538a09f498dbc03 Mon Sep 17 00:00:00 2001 From: Pierre Ossman Date: Sun, 6 Jul 2008 01:10:27 +0200 Subject: mmc: remove multiwrite capability Relax requirements on host controllers and only require that they do not report a transfer count than is larger than the actual one (i.e. a lower value is okay). This is how many other parts of the kernel behaves so upper layers should already be prepared to handle that scenario. This gives us a performance boost on MMC cards. Signed-off-by: Pierre Ossman --- drivers/mmc/card/block.c | 47 ++++++++++++++++++-------------------------- drivers/mmc/host/at91_mci.c | 2 +- drivers/mmc/host/atmel-mci.c | 2 +- drivers/mmc/host/mmc_spi.c | 5 +---- drivers/mmc/host/mmci.c | 1 - drivers/mmc/host/omap.c | 2 +- drivers/mmc/host/tifm_sd.c | 2 +- drivers/mmc/host/wbsd.c | 2 +- include/linux/mmc/host.h | 11 +++++------ 9 files changed, 30 insertions(+), 44 deletions(-) diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c index 4b0f822..66e5a54 100644 --- a/drivers/mmc/card/block.c +++ b/drivers/mmc/card/block.c @@ -237,17 +237,6 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req) if (brq.data.blocks > card->host->max_blk_count) brq.data.blocks = card->host->max_blk_count; - /* - * If the host doesn't support multiple block writes, force - * block writes to single block. SD cards are excepted from - * this rule as they support querying the number of - * successfully written sectors. - */ - if (rq_data_dir(req) != READ && - !(card->host->caps & MMC_CAP_MULTIWRITE) && - !mmc_card_sd(card)) - brq.data.blocks = 1; - if (brq.data.blocks > 1) { /* SPI multiblock writes terminate using a special * token, not a STOP_TRANSMISSION request. @@ -367,30 +356,32 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req) * mark the known good sectors as ok. * * If the card is not SD, we can still ok written sectors - * if the controller can do proper error reporting. + * as reported by the controller (which might be less than + * the real number of written sectors, but never more). * * For reads we just fail the entire chunk as that should * be safe in all cases. */ - if (rq_data_dir(req) != READ && mmc_card_sd(card)) { - u32 blocks; - unsigned int bytes; - - blocks = mmc_sd_num_wr_blocks(card); - if (blocks != (u32)-1) { - if (card->csd.write_partial) - bytes = blocks << md->block_bits; - else - bytes = blocks << 9; + if (rq_data_dir(req) != READ) { + if (mmc_card_sd(card)) { + u32 blocks; + unsigned int bytes; + + blocks = mmc_sd_num_wr_blocks(card); + if (blocks != (u32)-1) { + if (card->csd.write_partial) + bytes = blocks << md->block_bits; + else + bytes = blocks << 9; + spin_lock_irq(&md->lock); + ret = __blk_end_request(req, 0, bytes); + spin_unlock_irq(&md->lock); + } + } else { spin_lock_irq(&md->lock); - ret = __blk_end_request(req, 0, bytes); + ret = __blk_end_request(req, 0, brq.data.bytes_xfered); spin_unlock_irq(&md->lock); } - } else if (rq_data_dir(req) != READ && - (card->host->caps & MMC_CAP_MULTIWRITE)) { - spin_lock_irq(&md->lock); - ret = __blk_end_request(req, 0, brq.data.bytes_xfered); - spin_unlock_irq(&md->lock); } mmc_release_host(card->host); diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index 16df235..f15e206 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -995,7 +995,7 @@ static int __init at91_mci_probe(struct platform_device *pdev) mmc->f_min = 375000; mmc->f_max = 25000000; mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; - mmc->caps = MMC_CAP_MULTIWRITE | MMC_CAP_SDIO_IRQ; + mmc->caps = MMC_CAP_SDIO_IRQ; mmc->max_blk_size = 4095; mmc->max_blk_count = mmc->max_req_size; diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c index 25d5324a..cce873c 100644 --- a/drivers/mmc/host/atmel-mci.c +++ b/drivers/mmc/host/atmel-mci.c @@ -849,7 +849,7 @@ static int __init atmci_probe(struct platform_device *pdev) mmc->f_min = (host->bus_hz + 511) / 512; mmc->f_max = host->bus_hz / 2; mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; - mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE; + mmc->caps |= MMC_CAP_4_BIT_DATA; mmc->max_hw_segs = 64; mmc->max_phys_segs = 64; diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c index 4e82f64..41cc633 100644 --- a/drivers/mmc/host/mmc_spi.c +++ b/drivers/mmc/host/mmc_spi.c @@ -1252,10 +1252,7 @@ static int mmc_spi_probe(struct spi_device *spi) mmc->ops = &mmc_spi_ops; mmc->max_blk_size = MMC_SPI_BLOCKSIZE; - /* As long as we keep track of the number of successfully - * transmitted blocks, we're good for multiwrite. - */ - mmc->caps = MMC_CAP_SPI | MMC_CAP_MULTIWRITE; + mmc->caps = MMC_CAP_SPI; /* SPI doesn't need the lowspeed device identification thing for * MMC or SD cards, since it never comes up in open drain mode. diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index da5feca..696cf36 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -535,7 +535,6 @@ static int mmci_probe(struct amba_device *dev, void *id) mmc->f_min = (host->mclk + 511) / 512; mmc->f_max = min(host->mclk, fmax); mmc->ocr_avail = plat->ocr_mask; - mmc->caps = MMC_CAP_MULTIWRITE; /* * We can do SGIO diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c index 549517c..dbc26eb6 100644 --- a/drivers/mmc/host/omap.c +++ b/drivers/mmc/host/omap.c @@ -1317,7 +1317,7 @@ static int __init mmc_omap_new_slot(struct mmc_omap_host *host, int id) host->slots[id] = slot; - mmc->caps = MMC_CAP_MULTIWRITE; + mmc->caps = 0; if (host->pdata->conf.wire4) mmc->caps |= MMC_CAP_4_BIT_DATA; diff --git a/drivers/mmc/host/tifm_sd.c b/drivers/mmc/host/tifm_sd.c index 1c14a18..1384484 100644 --- a/drivers/mmc/host/tifm_sd.c +++ b/drivers/mmc/host/tifm_sd.c @@ -973,7 +973,7 @@ static int tifm_sd_probe(struct tifm_dev *sock) mmc->ops = &tifm_sd_ops; mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; - mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE; + mmc->caps = MMC_CAP_4_BIT_DATA; mmc->f_min = 20000000 / 60; mmc->f_max = 24000000; diff --git a/drivers/mmc/host/wbsd.c b/drivers/mmc/host/wbsd.c index f7dcd8e..adda379 100644 --- a/drivers/mmc/host/wbsd.c +++ b/drivers/mmc/host/wbsd.c @@ -1219,7 +1219,7 @@ static int __devinit wbsd_alloc_mmc(struct device *dev) mmc->f_min = 375000; mmc->f_max = 24000000; mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; - mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE; + mmc->caps = MMC_CAP_4_BIT_DATA; spin_lock_init(&host->lock); diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index 753b723..10a2080 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -111,12 +111,11 @@ struct mmc_host { unsigned long caps; /* Host capabilities */ #define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */ -#define MMC_CAP_MULTIWRITE (1 << 1) /* Can accurately report bytes sent to card on error */ -#define MMC_CAP_MMC_HIGHSPEED (1 << 2) /* Can do MMC high-speed timing */ -#define MMC_CAP_SD_HIGHSPEED (1 << 3) /* Can do SD high-speed timing */ -#define MMC_CAP_SDIO_IRQ (1 << 4) /* Can signal pending SDIO IRQs */ -#define MMC_CAP_SPI (1 << 5) /* Talks only SPI protocols */ -#define MMC_CAP_NEEDS_POLL (1 << 6) /* Needs polling for card-detection */ +#define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */ +#define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */ +#define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */ +#define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */ +#define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */ /* host specific block data */ unsigned int max_seg_size; /* see blk_queue_max_segment_size */ -- cgit v1.1 From c8b3e02eb250ceb661437e9b198757eff0eb6fd2 Mon Sep 17 00:00:00 2001 From: Tomas Winkler Date: Sat, 5 Jul 2008 19:52:04 +0300 Subject: mmc: fix spares errors of sdhci.c 1. sdhci_prepare_data: fix shadowing of count variable u8 count int count -> sg_cnt; 2. sdhci_add_host: assignment of integer to pointer dma_mask = 0 -> dma_mask = NULL; Signed-off-by: Tomas Winkler Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index d3e4a39..13bd681 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -672,14 +672,14 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_data *data) host->ioaddr + SDHCI_ADMA_ADDRESS); } } else { - int count; + int sg_cnt; - count = dma_map_sg(mmc_dev(host->mmc), + sg_cnt = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len, (data->flags & MMC_DATA_READ) ? DMA_FROM_DEVICE : DMA_TO_DEVICE); - if (count == 0) { + if (sg_cnt == 0) { /* * This only happens when someone fed * us an invalid request. @@ -1583,7 +1583,7 @@ int sdhci_add_host(struct sdhci_host *host) /* XXX: Hack to get MMC layer to avoid highmem */ if (!(host->flags & SDHCI_USE_DMA)) - mmc_dev(host->mmc)->dma_mask = 0; + mmc_dev(host->mmc)->dma_mask = NULL; host->max_clk = (caps & SDHCI_CLOCK_BASE_MASK) >> SDHCI_CLOCK_BASE_SHIFT; -- cgit v1.1 From c71f65129a1fb67bc6b9b8d03b493675b5c9302b Mon Sep 17 00:00:00 2001 From: Andres Salomon Date: Mon, 7 Jul 2008 17:25:56 -0400 Subject: mmc: OLPC: update vdd/powerup quirk comment This comment update got lost in the great floo^Wmerge. As Pierre pointed out, no one knows what 'CaFe' is. Signed-off-by: Andres Salomon Signed-off-by: Pierre Ossman --- drivers/mmc/host/sdhci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index 13bd681..17701c3 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -978,7 +978,7 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned short power) } /* - * At least the CaFe chip gets confused if we set the voltage + * At least the Marvell CaFe chip gets confused if we set the voltage * and set turn on power at the same time, so set the voltage first. */ if ((host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER)) -- cgit v1.1 From 62a7573ee9f31d4fdb330b3e68ebf6efaba1d57c Mon Sep 17 00:00:00 2001 From: Benzi Zbit Date: Thu, 10 Jul 2008 02:41:43 +0300 Subject: sdio: fix the use of hard coded timeout value. This adds reading and using of enable_timeout from the CIS Signed-off-by: Benzi Zbit Signed-off-by: Tomas Winkler Signed-off-by: Pierre Ossman --- drivers/mmc/core/sdio_cis.c | 6 ++++++ drivers/mmc/core/sdio_io.c | 6 +----- include/linux/mmc/sdio_func.h | 2 ++ 3 files changed, 9 insertions(+), 5 deletions(-) diff --git a/drivers/mmc/core/sdio_cis.c b/drivers/mmc/core/sdio_cis.c index d5e51b1..956bd76 100644 --- a/drivers/mmc/core/sdio_cis.c +++ b/drivers/mmc/core/sdio_cis.c @@ -129,6 +129,12 @@ static int cistpl_funce_func(struct sdio_func *func, /* TPLFE_MAX_BLK_SIZE */ func->max_blksize = buf[12] | (buf[13] << 8); + /* TPLFE_ENABLE_TIMEOUT_VAL, present in ver 1.1 and above */ + if (vsn > SDIO_SDIO_REV_1_00) + func->enable_timeout = (buf[28] | (buf[29] << 8)) * 10; + else + func->enable_timeout = jiffies_to_msecs(HZ); + return 0; } diff --git a/drivers/mmc/core/sdio_io.c b/drivers/mmc/core/sdio_io.c index 3ccf691..0888df6 100755 --- a/drivers/mmc/core/sdio_io.c +++ b/drivers/mmc/core/sdio_io.c @@ -76,11 +76,7 @@ int sdio_enable_func(struct sdio_func *func) if (ret) goto err; - /* - * FIXME: This should timeout based on information in the CIS, - * but we don't have card to parse that yet. - */ - timeout = jiffies + HZ; + timeout = jiffies + msecs_to_jiffies(func->enable_timeout); while (1) { ret = mmc_io_rw_direct(func->card, 0, 0, SDIO_CCCR_IORx, 0, ®); diff --git a/include/linux/mmc/sdio_func.h b/include/linux/mmc/sdio_func.h index 28fb0a3..07bee4a 100755 --- a/include/linux/mmc/sdio_func.h +++ b/include/linux/mmc/sdio_func.h @@ -46,6 +46,8 @@ struct sdio_func { unsigned max_blksize; /* maximum block size */ unsigned cur_blksize; /* current block size */ + unsigned enable_timeout; /* max enable timeout in msec */ + unsigned int state; /* function state */ #define SDIO_STATE_PRESENT (1<<0) /* present in sysfs */ -- cgit v1.1 From ea901300cd8b809285fa5cbced18124f127e0ac6 Mon Sep 17 00:00:00 2001 From: Tomas Winkler Date: Thu, 10 Jul 2008 03:01:56 +0300 Subject: sdio: sdio_io.c Fix sparse warnings Unfold nested macros it creates not readable code and sparse warnings sdio_io.c:190:9: warning: symbol '_min1' shadows an earlier one Signed-off-by: Tomas Winkler Signed-off-by: Pierre Ossman --- drivers/mmc/core/sdio_io.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) diff --git a/drivers/mmc/core/sdio_io.c b/drivers/mmc/core/sdio_io.c index 0888df6..f61fc2d 100755 --- a/drivers/mmc/core/sdio_io.c +++ b/drivers/mmc/core/sdio_io.c @@ -187,11 +187,10 @@ EXPORT_SYMBOL_GPL(sdio_set_block_size); */ static inline unsigned int sdio_max_byte_size(struct sdio_func *func) { - return min(min(min( - func->card->host->max_seg_size, - func->card->host->max_blk_size), - func->max_blksize), - 512u); /* maximum size for byte mode */ + unsigned mval = min(func->card->host->max_seg_size, + func->card->host->max_blk_size); + mval = min(mval, func->max_blksize); + return min(mval, 512u); /* maximum size for byte mode */ } /** -- cgit v1.1 From 6a36913a33cf3d366e124f25c486a71212d02bce Mon Sep 17 00:00:00 2001 From: Sascha Sommer Date: Tue, 15 Jul 2008 14:21:29 +0200 Subject: mmc: host driver for Ricoh Bay1Controllers Signed-off-by: Sascha Sommer Signed-off-by: Pierre Ossman --- MAINTAINERS | 6 + drivers/mmc/host/Kconfig | 10 + drivers/mmc/host/Makefile | 2 + drivers/mmc/host/sdricoh_cs.c | 575 ++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 593 insertions(+) create mode 100644 drivers/mmc/host/sdricoh_cs.c diff --git a/MAINTAINERS b/MAINTAINERS index 9def20a..c16b986 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3609,6 +3609,12 @@ P: Jim Cromie M: jim.cromie@gmail.com S: Maintained +SDRICOH_CS MMC/SD HOST CONTROLLER INTERFACE DRIVER +P: Sascha Sommer +M: saschasommer@freenet.de +L: sdricohcs-devel@lists.sourceforge.net (subscribers-only) +S: Maintained + SECURITY CONTACT P: Security Officers M: security@kernel.org diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index 198df42..dc6f257 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -164,3 +164,13 @@ config MMC_S3C If unsure, say N. +config MMC_SDRICOH_CS + tristate "MMC/SD driver for Ricoh Bay1Controllers (EXPERIMENTAL)" + depends on EXPERIMENTAL && MMC && PCI && PCMCIA + help + Say Y here if your Notebook reports a Ricoh Bay1Controller PCMCIA + card whenever you insert a MMC or SD card into the card slot. + + To compile this driver as a module, choose M here: the + module will be called sdricoh_cs. + diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index 2dc9ff2..db52eeb 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -20,3 +20,5 @@ obj-$(CONFIG_MMC_ATMELMCI) += atmel-mci.o obj-$(CONFIG_MMC_TIFM_SD) += tifm_sd.o obj-$(CONFIG_MMC_SPI) += mmc_spi.o obj-$(CONFIG_MMC_S3C) += s3cmci.o +obj-$(CONFIG_MMC_SDRICOH_CS) += sdricoh_cs.o + diff --git a/drivers/mmc/host/sdricoh_cs.c b/drivers/mmc/host/sdricoh_cs.c new file mode 100644 index 0000000..f99e9f7 --- /dev/null +++ b/drivers/mmc/host/sdricoh_cs.c @@ -0,0 +1,575 @@ +/* + * sdricoh_cs.c - driver for Ricoh Secure Digital Card Readers that can be + * found on some Ricoh RL5c476 II cardbus bridge + * + * Copyright (C) 2006 - 2008 Sascha Sommer + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + * + */ + +/* +#define DEBUG +#define VERBOSE_DEBUG +*/ +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#include + +#define DRIVER_NAME "sdricoh_cs" + +static unsigned int switchlocked; + +/* i/o region */ +#define SDRICOH_PCI_REGION 0 +#define SDRICOH_PCI_REGION_SIZE 0x1000 + +/* registers */ +#define R104_VERSION 0x104 +#define R200_CMD 0x200 +#define R204_CMD_ARG 0x204 +#define R208_DATAIO 0x208 +#define R20C_RESP 0x20c +#define R21C_STATUS 0x21c +#define R2E0_INIT 0x2e0 +#define R2E4_STATUS_RESP 0x2e4 +#define R2F0_RESET 0x2f0 +#define R224_MODE 0x224 +#define R226_BLOCKSIZE 0x226 +#define R228_POWER 0x228 +#define R230_DATA 0x230 + +/* flags for the R21C_STATUS register */ +#define STATUS_CMD_FINISHED 0x00000001 +#define STATUS_TRANSFER_FINISHED 0x00000004 +#define STATUS_CARD_INSERTED 0x00000020 +#define STATUS_CARD_LOCKED 0x00000080 +#define STATUS_CMD_TIMEOUT 0x00400000 +#define STATUS_READY_TO_READ 0x01000000 +#define STATUS_READY_TO_WRITE 0x02000000 +#define STATUS_BUSY 0x40000000 + +/* timeouts */ +#define INIT_TIMEOUT 100 +#define CMD_TIMEOUT 100000 +#define TRANSFER_TIMEOUT 100000 +#define BUSY_TIMEOUT 32767 + +/* list of supported pcmcia devices */ +static struct pcmcia_device_id pcmcia_ids[] = { + /* vendor and device strings followed by their crc32 hashes */ + PCMCIA_DEVICE_PROD_ID12("RICOH", "Bay1Controller", 0xd9f522ed, + 0xc3901202), + PCMCIA_DEVICE_NULL, +}; + +MODULE_DEVICE_TABLE(pcmcia, pcmcia_ids); + +/* mmc privdata */ +struct sdricoh_host { + struct device *dev; + struct mmc_host *mmc; /* MMC structure */ + unsigned char __iomem *iobase; + struct pci_dev *pci_dev; + int app_cmd; +}; + +/***************** register i/o helper functions *****************************/ + +static inline unsigned int sdricoh_readl(struct sdricoh_host *host, + unsigned int reg) +{ + unsigned int value = readl(host->iobase + reg); + dev_vdbg(host->dev, "rl %x 0x%x\n", reg, value); + return value; +} + +static inline void sdricoh_writel(struct sdricoh_host *host, unsigned int reg, + unsigned int value) +{ + writel(value, host->iobase + reg); + dev_vdbg(host->dev, "wl %x 0x%x\n", reg, value); + +} + +static inline unsigned int sdricoh_readw(struct sdricoh_host *host, + unsigned int reg) +{ + unsigned int value = readw(host->iobase + reg); + dev_vdbg(host->dev, "rb %x 0x%x\n", reg, value); + return value; +} + +static inline void sdricoh_writew(struct sdricoh_host *host, unsigned int reg, + unsigned short value) +{ + writew(value, host->iobase + reg); + dev_vdbg(host->dev, "ww %x 0x%x\n", reg, value); +} + +static inline unsigned int sdricoh_readb(struct sdricoh_host *host, + unsigned int reg) +{ + unsigned int value = readb(host->iobase + reg); + dev_vdbg(host->dev, "rb %x 0x%x\n", reg, value); + return value; +} + +static int sdricoh_query_status(struct sdricoh_host *host, unsigned int wanted, + unsigned int timeout){ + unsigned int loop; + unsigned int status = 0; + struct device *dev = host->dev; + for (loop = 0; loop < timeout; loop++) { + status = sdricoh_readl(host, R21C_STATUS); + sdricoh_writel(host, R2E4_STATUS_RESP, status); + if (status & wanted) + break; + } + + if (loop == timeout) { + dev_err(dev, "query_status: timeout waiting for %x\n", wanted); + return -ETIMEDOUT; + } + + /* do not do this check in the loop as some commands fail otherwise */ + if (status & 0x7F0000) { + dev_err(dev, "waiting for status bit %x failed\n", wanted); + return -EINVAL; + } + return 0; + +} + +static int sdricoh_mmc_cmd(struct sdricoh_host *host, unsigned char opcode, + unsigned int arg) +{ + unsigned int status; + int result = 0; + unsigned int loop = 0; + /* reset status reg? */ + sdricoh_writel(host, R21C_STATUS, 0x18); + /* fill parameters */ + sdricoh_writel(host, R204_CMD_ARG, arg); + sdricoh_writel(host, R200_CMD, (0x10000 << 8) | opcode); + /* wait for command completion */ + if (opcode) { + for (loop = 0; loop < CMD_TIMEOUT; loop++) { + status = sdricoh_readl(host, R21C_STATUS); + sdricoh_writel(host, R2E4_STATUS_RESP, status); + if (status & STATUS_CMD_FINISHED) + break; + } + /* don't check for timeout in the loop it is not always + reset correctly + */ + if (loop == CMD_TIMEOUT || status & STATUS_CMD_TIMEOUT) + result = -ETIMEDOUT; + + } + + return result; + +} + +static int sdricoh_reset(struct sdricoh_host *host) +{ + dev_dbg(host->dev, "reset\n"); + sdricoh_writel(host, R2F0_RESET, 0x10001); + sdricoh_writel(host, R2E0_INIT, 0x10000); + if (sdricoh_readl(host, R2E0_INIT) != 0x10000) + return -EIO; + sdricoh_writel(host, R2E0_INIT, 0x10007); + + sdricoh_writel(host, R224_MODE, 0x2000000); + sdricoh_writel(host, R228_POWER, 0xe0); + + + /* status register ? */ + sdricoh_writel(host, R21C_STATUS, 0x18); + + return 0; +} + +static int sdricoh_blockio(struct sdricoh_host *host, int read, + u8 *buf, int len) +{ + int size; + u32 data = 0; + /* wait until the data is available */ + if (read) { + if (sdricoh_query_status(host, STATUS_READY_TO_READ, + TRANSFER_TIMEOUT)) + return -ETIMEDOUT; + sdricoh_writel(host, R21C_STATUS, 0x18); + /* read data */ + while (len) { + data = sdricoh_readl(host, R230_DATA); + size = min(len, 4); + len -= size; + while (size) { + *buf = data & 0xFF; + buf++; + data >>= 8; + size--; + } + } + } else { + if (sdricoh_query_status(host, STATUS_READY_TO_WRITE, + TRANSFER_TIMEOUT)) + return -ETIMEDOUT; + sdricoh_writel(host, R21C_STATUS, 0x18); + /* write data */ + while (len) { + size = min(len, 4); + len -= size; + while (size) { + data >>= 8; + data |= (u32)*buf << 24; + buf++; + size--; + } + sdricoh_writel(host, R230_DATA, data); + } + } + + if (len) + return -EIO; + + return 0; +} + +static void sdricoh_request(struct mmc_host *mmc, struct mmc_request *mrq) +{ + struct sdricoh_host *host = mmc_priv(mmc); + struct mmc_command *cmd = mrq->cmd; + struct mmc_data *data = cmd->data; + struct device *dev = host->dev; + unsigned char opcode = cmd->opcode; + int i; + + dev_dbg(dev, "=============================\n"); + dev_dbg(dev, "sdricoh_request opcode=%i\n", opcode); + + sdricoh_writel(host, R21C_STATUS, 0x18); + + /* MMC_APP_CMDs need some special handling */ + if (host->app_cmd) { + opcode |= 64; + host->app_cmd = 0; + } else if (opcode == 55) + host->app_cmd = 1; + + /* read/write commands seem to require this */ + if (data) { + sdricoh_writew(host, R226_BLOCKSIZE, data->blksz); + sdricoh_writel(host, R208_DATAIO, 0); + } + + cmd->error = sdricoh_mmc_cmd(host, opcode, cmd->arg); + + /* read response buffer */ + if (cmd->flags & MMC_RSP_PRESENT) { + if (cmd->flags & MMC_RSP_136) { + /* CRC is stripped so we need to do some shifting. */ + for (i = 0; i < 4; i++) { + cmd->resp[i] = + sdricoh_readl(host, + R20C_RESP + (3 - i) * 4) << 8; + if (i != 3) + cmd->resp[i] |= + sdricoh_readb(host, R20C_RESP + + (3 - i) * 4 - 1); + } + } else + cmd->resp[0] = sdricoh_readl(host, R20C_RESP); + } + + /* transfer data */ + if (data && cmd->error == 0) { + dev_dbg(dev, "transfer: blksz %i blocks %i sg_len %i " + "sg length %i\n", data->blksz, data->blocks, + data->sg_len, data->sg->length); + + /* enter data reading mode */ + sdricoh_writel(host, R21C_STATUS, 0x837f031e); + for (i = 0; i < data->blocks; i++) { + size_t len = data->blksz; + u8 *buf; + struct page *page; + int result; + page = sg_page(data->sg); + + buf = kmap(page) + data->sg->offset + (len * i); + result = + sdricoh_blockio(host, + data->flags & MMC_DATA_READ, buf, len); + kunmap(page); + flush_dcache_page(page); + if (result) { + dev_err(dev, "sdricoh_request: cmd %i " + "block transfer failed\n", cmd->opcode); + cmd->error = result; + break; + } else + data->bytes_xfered += len; + } + + sdricoh_writel(host, R208_DATAIO, 1); + + if (sdricoh_query_status(host, STATUS_TRANSFER_FINISHED, + TRANSFER_TIMEOUT)) { + dev_err(dev, "sdricoh_request: transfer end error\n"); + cmd->error = -EINVAL; + } + } + /* FIXME check busy flag */ + + mmc_request_done(mmc, mrq); + dev_dbg(dev, "=============================\n"); +} + +static void sdricoh_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct sdricoh_host *host = mmc_priv(mmc); + dev_dbg(host->dev, "set_ios\n"); + + if (ios->power_mode == MMC_POWER_ON) { + sdricoh_writel(host, R228_POWER, 0xc0e0); + + if (ios->bus_width == MMC_BUS_WIDTH_4) { + sdricoh_writel(host, R224_MODE, 0x2000300); + sdricoh_writel(host, R228_POWER, 0x40e0); + } else { + sdricoh_writel(host, R224_MODE, 0x2000340); + } + + } else if (ios->power_mode == MMC_POWER_UP) { + sdricoh_writel(host, R224_MODE, 0x2000320); + sdricoh_writel(host, R228_POWER, 0xe0); + } +} + +static int sdricoh_get_ro(struct mmc_host *mmc) +{ + struct sdricoh_host *host = mmc_priv(mmc); + unsigned int status; + + status = sdricoh_readl(host, R21C_STATUS); + sdricoh_writel(host, R2E4_STATUS_RESP, status); + + /* some notebooks seem to have the locked flag switched */ + if (switchlocked) + return !(status & STATUS_CARD_LOCKED); + + return (status & STATUS_CARD_LOCKED); +} + +static struct mmc_host_ops sdricoh_ops = { + .request = sdricoh_request, + .set_ios = sdricoh_set_ios, + .get_ro = sdricoh_get_ro, +}; + +/* initialize the control and register it to the mmc framework */ +static int sdricoh_init_mmc(struct pci_dev *pci_dev, + struct pcmcia_device *pcmcia_dev) +{ + int result = 0; + void __iomem *iobase = NULL; + struct mmc_host *mmc = NULL; + struct sdricoh_host *host = NULL; + struct device *dev = &pcmcia_dev->dev; + /* map iomem */ + if (pci_resource_len(pci_dev, SDRICOH_PCI_REGION) != + SDRICOH_PCI_REGION_SIZE) { + dev_dbg(dev, "unexpected pci resource len\n"); + return -ENODEV; + } + iobase = + pci_iomap(pci_dev, SDRICOH_PCI_REGION, SDRICOH_PCI_REGION_SIZE); + if (!iobase) { + dev_err(dev, "unable to map iobase\n"); + return -ENODEV; + } + /* check version? */ + if (readl(iobase + R104_VERSION) != 0x4000) { + dev_dbg(dev, "no supported mmc controller found\n"); + result = -ENODEV; + goto err; + } + /* allocate privdata */ + mmc = pcmcia_dev->priv = + mmc_alloc_host(sizeof(struct sdricoh_host), &pcmcia_dev->dev); + if (!mmc) { + dev_err(dev, "mmc_alloc_host failed\n"); + result = -ENOMEM; + goto err; + } + host = mmc_priv(mmc); + + host->iobase = iobase; + host->dev = dev; + host->pci_dev = pci_dev; + + mmc->ops = &sdricoh_ops; + + /* FIXME: frequency and voltage handling is done by the controller + */ + mmc->f_min = 450000; + mmc->f_max = 24000000; + mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; + mmc->caps |= MMC_CAP_4_BIT_DATA; + + mmc->max_seg_size = 1024 * 512; + mmc->max_blk_size = 512; + + /* reset the controler */ + if (sdricoh_reset(host)) { + dev_dbg(dev, "could not reset\n"); + result = -EIO; + goto err; + + } + + result = mmc_add_host(mmc); + + if (!result) { + dev_dbg(dev, "mmc host registered\n"); + return 0; + } + +err: + if (iobase) + iounmap(iobase); + if (mmc) + mmc_free_host(mmc); + + return result; +} + +/* search for supported mmc controllers */ +static int sdricoh_pcmcia_probe(struct pcmcia_device *pcmcia_dev) +{ + struct pci_dev *pci_dev = NULL; + + dev_info(&pcmcia_dev->dev, "Searching MMC controller for pcmcia device" + " %s %s ...\n", pcmcia_dev->prod_id[0], pcmcia_dev->prod_id[1]); + + /* search pci cardbus bridge that contains the mmc controler */ + /* the io region is already claimed by yenta_socket... */ + while ((pci_dev = + pci_get_device(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, + pci_dev))) { + /* try to init the device */ + if (!sdricoh_init_mmc(pci_dev, pcmcia_dev)) { + dev_info(&pcmcia_dev->dev, "MMC controller found\n"); + return 0; + } + + } + dev_err(&pcmcia_dev->dev, "No MMC controller was found.\n"); + return -ENODEV; +} + +static void sdricoh_pcmcia_detach(struct pcmcia_device *link) +{ + struct mmc_host *mmc = link->priv; + + dev_dbg(&link->dev, "detach\n"); + + /* remove mmc host */ + if (mmc) { + struct sdricoh_host *host = mmc_priv(mmc); + mmc_remove_host(mmc); + pci_iounmap(host->pci_dev, host->iobase); + pci_dev_put(host->pci_dev); + mmc_free_host(mmc); + } + pcmcia_disable_device(link); + +} + +#ifdef CONFIG_PM +static int sdricoh_pcmcia_suspend(struct pcmcia_device *link) +{ + struct mmc_host *mmc = link->priv; + dev_dbg(&link->dev, "suspend\n"); + mmc_suspend_host(mmc, PMSG_SUSPEND); + return 0; +} + +static int sdricoh_pcmcia_resume(struct pcmcia_device *link) +{ + struct mmc_host *mmc = link->priv; + dev_dbg(&link->dev, "resume\n"); + sdricoh_reset(mmc_priv(mmc)); + mmc_resume_host(mmc); + return 0; +} +#else +#define sdricoh_pcmcia_suspend NULL +#define sdricoh_pcmcia_resume NULL +#endif + +static struct pcmcia_driver sdricoh_driver = { + .drv = { + .name = DRIVER_NAME, + }, + .probe = sdricoh_pcmcia_probe, + .remove = sdricoh_pcmcia_detach, + .id_table = pcmcia_ids, + .suspend = sdricoh_pcmcia_suspend, + .resume = sdricoh_pcmcia_resume, +}; + +/*****************************************************************************\ + * * + * Driver init/exit * + * * +\*****************************************************************************/ + +static int __init sdricoh_drv_init(void) +{ + return pcmcia_register_driver(&sdricoh_driver); +} + +static void __exit sdricoh_drv_exit(void) +{ + pcmcia_unregister_driver(&sdricoh_driver); +} + +module_init(sdricoh_drv_init); +module_exit(sdricoh_drv_exit); + +module_param(switchlocked, uint, 0444); + +MODULE_AUTHOR("Sascha Sommer "); +MODULE_DESCRIPTION("Ricoh PCMCIA Secure Digital Interface driver"); +MODULE_LICENSE("GPL"); + +MODULE_PARM_DESC(switchlocked, "Switch the cards locked status." + "Use this when unlocked cards are shown readonly (default 0)"); -- cgit v1.1 From c43d8636971c39da993e94082fd65bfff421618e Mon Sep 17 00:00:00 2001 From: David Howells Date: Thu, 10 Jul 2008 12:28:48 +0100 Subject: sdio_uart: Fix SDIO break control to now return success or an error This is a consequence of patch 9ea761bfef52c116fed4715d4043392c2503fe6a. Signed-off-by: David Howells Signed-off-by: Pierre Ossman --- drivers/mmc/card/sdio_uart.c | 9 ++++++--- 1 file changed, 6 insertions(+), 3 deletions(-) diff --git a/drivers/mmc/card/sdio_uart.c b/drivers/mmc/card/sdio_uart.c index eeea84c..78ad487 100644 --- a/drivers/mmc/card/sdio_uart.c +++ b/drivers/mmc/card/sdio_uart.c @@ -885,12 +885,14 @@ static void sdio_uart_set_termios(struct tty_struct *tty, struct ktermios *old_t sdio_uart_release_func(port); } -static void sdio_uart_break_ctl(struct tty_struct *tty, int break_state) +static int sdio_uart_break_ctl(struct tty_struct *tty, int break_state) { struct sdio_uart_port *port = tty->driver_data; + int result; - if (sdio_uart_claim_func(port) != 0) - return; + result = sdio_uart_claim_func(port); + if (result != 0) + return result; if (break_state == -1) port->lcr |= UART_LCR_SBC; @@ -899,6 +901,7 @@ static void sdio_uart_break_ctl(struct tty_struct *tty, int break_state) sdio_out(port, UART_LCR, port->lcr); sdio_uart_release_func(port); + return 0; } static int sdio_uart_tiocmget(struct tty_struct *tty, struct file *file) -- cgit v1.1