From 46bc85872040ae7a98b983514bf79f68255b2643 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Fri, 29 Oct 2010 18:42:22 +0900 Subject: sh: mach-microdev: SuperIO-relative ioport mapping. The microdev only has to contend with silly PIO mangling on anything within the SuperIO range. As each of the SuperIO modules is already speciail cased, we just shift that logic over to the ioport map. With microdev PCI never being merged (and being fudamentally broken in hardware), and the ethernet chip only doing 16-bit accesses already, there's no need to maintain any of the extra special casing. Kill it all off. Signed-off-by: Paul Mundt --- arch/sh/boards/mach-microdev/io.c | 246 +--------------------------- arch/sh/boards/mach-microdev/setup.c | 23 +-- arch/sh/include/mach-common/mach/microdev.h | 9 - 3 files changed, 3 insertions(+), 275 deletions(-) diff --git a/arch/sh/boards/mach-microdev/io.c b/arch/sh/boards/mach-microdev/io.c index 2960c65..acdafb0 100644 --- a/arch/sh/boards/mach-microdev/io.c +++ b/arch/sh/boards/mach-microdev/io.c @@ -54,7 +54,7 @@ /* * map I/O ports to memory-mapped addresses */ -static unsigned long microdev_isa_port2addr(unsigned long offset) +void __iomem *microdev_ioport_map(unsigned long offset, unsigned int len) { unsigned long result; @@ -72,16 +72,6 @@ static unsigned long microdev_isa_port2addr(unsigned long offset) * Configuration Registers */ result = IO_SUPERIO_PHYS + (offset << 1); -#if 0 - } else if (offset == KBD_DATA_REG || offset == KBD_CNTL_REG || - offset == KBD_STATUS_REG) { - /* - * SMSC FDC37C93xAPM SuperIO chip - * - * PS/2 Keyboard + Mouse (ports 0x60 and 0x64). - */ - result = IO_SUPERIO_PHYS + (offset << 1); -#endif } else if (((offset >= IO_IDE1_BASE) && (offset < IO_IDE1_BASE + IO_IDE_EXTENT)) || (offset == IO_IDE1_MISC)) { @@ -131,237 +121,5 @@ static unsigned long microdev_isa_port2addr(unsigned long offset) result = PVR; } - return result; -} - -#define PORT2ADDR(x) (microdev_isa_port2addr(x)) - -static inline void delay(void) -{ -#if defined(CONFIG_PCI) - /* System board present, just make a dummy SRAM access. (CS0 will be - mapped to PCI memory, probably good to avoid it.) */ - __raw_readw(0xa6800000); -#else - /* CS0 will be mapped to flash, ROM etc so safe to access it. */ - __raw_readw(0xa0000000); -#endif -} - -unsigned char microdev_inb(unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) - return microdev_pci_inb(port); -#endif - return *(volatile unsigned char*)PORT2ADDR(port); -} - -unsigned short microdev_inw(unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) - return microdev_pci_inw(port); -#endif - return *(volatile unsigned short*)PORT2ADDR(port); -} - -unsigned int microdev_inl(unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) - return microdev_pci_inl(port); -#endif - return *(volatile unsigned int*)PORT2ADDR(port); -} - -void microdev_outw(unsigned short b, unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) { - microdev_pci_outw(b, port); - return; - } -#endif - *(volatile unsigned short*)PORT2ADDR(port) = b; -} - -void microdev_outb(unsigned char b, unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) { - microdev_pci_outb(b, port); - return; - } -#endif - - /* - * There is a board feature with the current SH4-202 MicroDev in - * that the 2 byte enables (nBE0 and nBE1) are tied together (and - * to the Chip Select Line (Ethernet_CS)). Due to this connectivity, - * it is not possible to safely perform 8-bit writes to the - * Ethernet registers, as 16-bits will be consumed from the Data - * lines (corrupting the other byte). Hence, this function is - * written to implement 16-bit read/modify/write for all byte-wide - * accesses. - * - * Note: there is no problem with byte READS (even or odd). - * - * Sean McGoogan - 16th June 2003. - */ - if ((port >= IO_LAN91C111_BASE) && - (port < IO_LAN91C111_BASE + IO_LAN91C111_EXTENT)) { - /* - * Then are trying to perform a byte-write to the - * LAN91C111. This needs special care. - */ - if (port % 2 == 1) { /* is the port odd ? */ - /* unset bit-0, i.e. make even */ - const unsigned long evenPort = port-1; - unsigned short word; - - /* - * do a 16-bit read/write to write to 'port', - * preserving even byte. - * - * Even addresses are bits 0-7 - * Odd addresses are bits 8-15 - */ - word = microdev_inw(evenPort); - word = (word & 0xffu) | (b << 8); - microdev_outw(word, evenPort); - } else { - /* else, we are trying to do an even byte write */ - unsigned short word; - - /* - * do a 16-bit read/write to write to 'port', - * preserving odd byte. - * - * Even addresses are bits 0-7 - * Odd addresses are bits 8-15 - */ - word = microdev_inw(port); - word = (word & 0xff00u) | (b); - microdev_outw(word, port); - } - } else { - *(volatile unsigned char*)PORT2ADDR(port) = b; - } -} - -void microdev_outl(unsigned int b, unsigned long port) -{ -#ifdef CONFIG_PCI - if (port >= PCIBIOS_MIN_IO) { - microdev_pci_outl(b, port); - return; - } -#endif - *(volatile unsigned int*)PORT2ADDR(port) = b; -} - -unsigned char microdev_inb_p(unsigned long port) -{ - unsigned char v = microdev_inb(port); - delay(); - return v; -} - -unsigned short microdev_inw_p(unsigned long port) -{ - unsigned short v = microdev_inw(port); - delay(); - return v; -} - -unsigned int microdev_inl_p(unsigned long port) -{ - unsigned int v = microdev_inl(port); - delay(); - return v; -} - -void microdev_outb_p(unsigned char b, unsigned long port) -{ - microdev_outb(b, port); - delay(); -} - -void microdev_outw_p(unsigned short b, unsigned long port) -{ - microdev_outw(b, port); - delay(); -} - -void microdev_outl_p(unsigned int b, unsigned long port) -{ - microdev_outl(b, port); - delay(); -} - -void microdev_insb(unsigned long port, void *buffer, unsigned long count) -{ - volatile unsigned char *port_addr; - unsigned char *buf = buffer; - - port_addr = (volatile unsigned char *)PORT2ADDR(port); - - while (count--) - *buf++ = *port_addr; -} - -void microdev_insw(unsigned long port, void *buffer, unsigned long count) -{ - volatile unsigned short *port_addr; - unsigned short *buf = buffer; - - port_addr = (volatile unsigned short *)PORT2ADDR(port); - - while (count--) - *buf++ = *port_addr; -} - -void microdev_insl(unsigned long port, void *buffer, unsigned long count) -{ - volatile unsigned long *port_addr; - unsigned int *buf = buffer; - - port_addr = (volatile unsigned long *)PORT2ADDR(port); - - while (count--) - *buf++ = *port_addr; -} - -void microdev_outsb(unsigned long port, const void *buffer, unsigned long count) -{ - volatile unsigned char *port_addr; - const unsigned char *buf = buffer; - - port_addr = (volatile unsigned char *)PORT2ADDR(port); - - while (count--) - *port_addr = *buf++; -} - -void microdev_outsw(unsigned long port, const void *buffer, unsigned long count) -{ - volatile unsigned short *port_addr; - const unsigned short *buf = buffer; - - port_addr = (volatile unsigned short *)PORT2ADDR(port); - - while (count--) - *port_addr = *buf++; -} - -void microdev_outsl(unsigned long port, const void *buffer, unsigned long count) -{ - volatile unsigned long *port_addr; - const unsigned int *buf = buffer; - - port_addr = (volatile unsigned long *)PORT2ADDR(port); - - while (count--) - *port_addr = *buf++; + return (void __iomem *)result; } diff --git a/arch/sh/boards/mach-microdev/setup.c b/arch/sh/boards/mach-microdev/setup.c index d1df2a4..d8a7472 100644 --- a/arch/sh/boards/mach-microdev/setup.c +++ b/arch/sh/boards/mach-microdev/setup.c @@ -195,27 +195,6 @@ device_initcall(microdev_devices_setup); static struct sh_machine_vector mv_sh4202_microdev __initmv = { .mv_name = "SH4-202 MicroDev", .mv_nr_irqs = 72, - - .mv_inb = microdev_inb, - .mv_inw = microdev_inw, - .mv_inl = microdev_inl, - .mv_outb = microdev_outb, - .mv_outw = microdev_outw, - .mv_outl = microdev_outl, - - .mv_inb_p = microdev_inb_p, - .mv_inw_p = microdev_inw_p, - .mv_inl_p = microdev_inl_p, - .mv_outb_p = microdev_outb_p, - .mv_outw_p = microdev_outw_p, - .mv_outl_p = microdev_outl_p, - - .mv_insb = microdev_insb, - .mv_insw = microdev_insw, - .mv_insl = microdev_insl, - .mv_outsb = microdev_outsb, - .mv_outsw = microdev_outsw, - .mv_outsl = microdev_outsl, - + .mv_ioport_map = microdev_ioport_map, .mv_init_irq = init_microdev_irq, }; diff --git a/arch/sh/include/mach-common/mach/microdev.h b/arch/sh/include/mach-common/mach/microdev.h index 1aed158..dcb05fa 100644 --- a/arch/sh/include/mach-common/mach/microdev.h +++ b/arch/sh/include/mach-common/mach/microdev.h @@ -68,13 +68,4 @@ extern void microdev_print_fpga_intc_status(void); #define __IO_PREFIX microdev #include -#if defined(CONFIG_PCI) -unsigned char microdev_pci_inb(unsigned long port); -unsigned short microdev_pci_inw(unsigned long port); -unsigned long microdev_pci_inl(unsigned long port); -void microdev_pci_outb(unsigned char data, unsigned long port); -void microdev_pci_outw(unsigned short data, unsigned long port); -void microdev_pci_outl(unsigned long data, unsigned long port); -#endif - #endif /* __ASM_SH_MICRODEV_H */ -- cgit v1.1 From 39c11984a4f36bd1ce7f90f7506824955f0f4863 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Fri, 29 Oct 2010 18:59:58 +0900 Subject: sh: mach-snapgear: Rip out superfluous PIO routines. None of these PIO routines do anything other than basic error checking, get rid of them and use the generic fallbacks. Signed-off-by: Paul Mundt --- arch/sh/boards/mach-snapgear/Makefile | 2 +- arch/sh/boards/mach-snapgear/io.c | 121 ---------------------------- arch/sh/boards/mach-snapgear/setup.c | 36 +++------ arch/sh/include/mach-common/mach/snapgear.h | 22 ----- 4 files changed, 11 insertions(+), 170 deletions(-) delete mode 100644 arch/sh/boards/mach-snapgear/io.c diff --git a/arch/sh/boards/mach-snapgear/Makefile b/arch/sh/boards/mach-snapgear/Makefile index d2d2f4b..bc92e34 100644 --- a/arch/sh/boards/mach-snapgear/Makefile +++ b/arch/sh/boards/mach-snapgear/Makefile @@ -2,4 +2,4 @@ # Makefile for the SnapGear specific parts of the kernel # -obj-y := setup.o io.o +obj-y := setup.o diff --git a/arch/sh/boards/mach-snapgear/io.c b/arch/sh/boards/mach-snapgear/io.c deleted file mode 100644 index 476650e..0000000 --- a/arch/sh/boards/mach-snapgear/io.c +++ /dev/null @@ -1,121 +0,0 @@ -/* - * Copyright (C) 2002 David McCullough - * Copyright (C) 2001 Ian da Silva, Jeremy Siegel - * Based largely on io_se.c. - * - * I/O routine for Hitachi 7751 SolutionEngine. - * - * Initial version only to support LAN access; some - * placeholder code from io_se.c left in with the - * expectation of later SuperIO and PCMCIA access. - */ -#include -#include -#include -#include -#include - -#ifdef CONFIG_SH_SECUREEDGE5410 -unsigned short secureedge5410_ioport; -#endif - -static inline volatile __u16 *port2adr(unsigned int port) -{ - maybebadio((unsigned long)port); - return (volatile __u16*)port; -} - -/* - * General outline: remap really low stuff [eventually] to SuperIO, - * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO) - * is mapped through the PCI IO window. Stuff with high bits (PXSEG) - * should be way beyond the window, and is used w/o translation for - * compatibility. - */ -unsigned char snapgear_inb(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned char *)port; - else - return (*port2adr(port)) & 0xff; -} - -unsigned char snapgear_inb_p(unsigned long port) -{ - unsigned char v; - - if (PXSEG(port)) - v = *(volatile unsigned char *)port; - else - v = (*port2adr(port))&0xff; - ctrl_delay(); - return v; -} - -unsigned short snapgear_inw(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned short *)port; - else if (port >= 0x2000) - return *port2adr(port); - else - maybebadio(port); - return 0; -} - -unsigned int snapgear_inl(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned long *)port; - else if (port >= 0x2000) - return *port2adr(port); - else - maybebadio(port); - return 0; -} - -void snapgear_outb(unsigned char value, unsigned long port) -{ - - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else - *(port2adr(port)) = value; -} - -void snapgear_outb_p(unsigned char value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else - *(port2adr(port)) = value; - ctrl_delay(); -} - -void snapgear_outw(unsigned short value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned short *)port = value; - else if (port >= 0x2000) - *port2adr(port) = value; - else - maybebadio(port); -} - -void snapgear_outl(unsigned int value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned long *)port = value; - else - maybebadio(port); -} - -void snapgear_insl(unsigned long port, void *addr, unsigned long count) -{ - maybebadio(port); -} - -void snapgear_outsl(unsigned long port, const void *addr, unsigned long count) -{ - maybebadio(port); -} diff --git a/arch/sh/boards/mach-snapgear/setup.c b/arch/sh/boards/mach-snapgear/setup.c index 331745d..10eeea9 100644 --- a/arch/sh/boards/mach-snapgear/setup.c +++ b/arch/sh/boards/mach-snapgear/setup.c @@ -1,6 +1,4 @@ /* - * linux/arch/sh/boards/snapgear/setup.c - * * Copyright (C) 2002 David McCullough * Copyright (C) 2003 Paul Mundt * @@ -24,13 +22,14 @@ #include #include +unsigned short secureedge5410_ioport; + /* * EraseConfig handling functions */ - static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id) { - (void)__raw_readb(0xb8000000); /* dummy read */ + ctrl_delay(); /* dummy read */ printk("SnapGear: erase switch interrupt!\n"); @@ -39,21 +38,22 @@ static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id) static int __init eraseconfig_init(void) { + unsigned int irq = evt2irq(0x240); + printk("SnapGear: EraseConfig init\n"); + /* Setup "EraseConfig" switch on external IRQ 0 */ - if (request_irq(IRL0_IRQ, eraseconfig_interrupt, IRQF_DISABLED, + if (request_irq(irq, eraseconfig_interrupt, IRQF_DISABLED, "Erase Config", NULL)) printk("SnapGear: failed to register IRQ%d for Reset witch\n", - IRL0_IRQ); + irq); else printk("SnapGear: registered EraseConfig switch on IRQ%d\n", - IRL0_IRQ); - return(0); + irq); + return 0; } - module_init(eraseconfig_init); -/****************************************************************************/ /* * Initialize IRQ setting * @@ -62,7 +62,6 @@ module_init(eraseconfig_init); * IRL2 = eth1 * IRL3 = crypto */ - static void __init init_snapgear_IRQ(void) { printk("Setup SnapGear IRQ/IPR ...\n"); @@ -76,20 +75,5 @@ static void __init init_snapgear_IRQ(void) static struct sh_machine_vector mv_snapgear __initmv = { .mv_name = "SnapGear SecureEdge5410", .mv_nr_irqs = 72, - - .mv_inb = snapgear_inb, - .mv_inw = snapgear_inw, - .mv_inl = snapgear_inl, - .mv_outb = snapgear_outb, - .mv_outw = snapgear_outw, - .mv_outl = snapgear_outl, - - .mv_inb_p = snapgear_inb_p, - .mv_inw_p = snapgear_inw, - .mv_inl_p = snapgear_inl, - .mv_outb_p = snapgear_outb_p, - .mv_outw_p = snapgear_outw, - .mv_outl_p = snapgear_outl, - .mv_init_irq = init_snapgear_IRQ, }; diff --git a/arch/sh/include/mach-common/mach/snapgear.h b/arch/sh/include/mach-common/mach/snapgear.h index 042d95f..3653b9a4 100644 --- a/arch/sh/include/mach-common/mach/snapgear.h +++ b/arch/sh/include/mach-common/mach/snapgear.h @@ -12,30 +12,9 @@ #ifndef _ASM_SH_IO_SNAPGEAR_H #define _ASM_SH_IO_SNAPGEAR_H -#if defined(CONFIG_CPU_SH4) -/* - * The external interrupt lines, these take up ints 0 - 15 inclusive - * depending on the priority for the interrupt. In fact the priority - * is the interrupt :-) - */ - -#define IRL0_IRQ 2 -#define IRL0_PRIORITY 13 - -#define IRL1_IRQ 5 -#define IRL1_PRIORITY 10 - -#define IRL2_IRQ 8 -#define IRL2_PRIORITY 7 - -#define IRL3_IRQ 11 -#define IRL3_PRIORITY 4 -#endif - #define __IO_PREFIX snapgear #include -#ifdef CONFIG_SH_SECUREEDGE5410 /* * We need to remember what was written to the ioport as some bits * are shared with other functions and you cannot read back what was @@ -66,6 +45,5 @@ extern unsigned short secureedge5410_ioport; ((secureedge5410_ioport & ~(mask)) | ((val) & (mask))))) #define SECUREEDGE_READ_IOPORT() \ ((*SECUREEDGE_IOPORT_ADDR&0x0817) | (secureedge5410_ioport&~0x0817)) -#endif #endif /* _ASM_SH_IO_SNAPGEAR_H */ -- cgit v1.1 From f6eec8d66400714e47add3d8341688a1e86c5de9 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Fri, 29 Oct 2010 19:06:53 +0900 Subject: sh: mach-snapgear: Kill off machtype, consolidate board def. Only the secureedge5410 was ever supported by this code, so make the board specification explicit rather than perpetuating a mach group. Signed-off-by: Paul Mundt --- arch/sh/Makefile | 1 - arch/sh/boards/Makefile | 1 + arch/sh/boards/board-secureedge5410.c | 79 +++++++++++++++++++++++ arch/sh/boards/mach-snapgear/Makefile | 5 -- arch/sh/boards/mach-snapgear/setup.c | 79 ----------------------- arch/sh/configs/secureedge5410_defconfig | 63 ++++++++++++++++++ arch/sh/configs/snapgear_defconfig | 63 ------------------ arch/sh/include/mach-common/mach/secureedge5410.h | 49 ++++++++++++++ arch/sh/include/mach-common/mach/snapgear.h | 49 -------------- drivers/rtc/rtc-ds1302.c | 2 +- 10 files changed, 193 insertions(+), 198 deletions(-) create mode 100644 arch/sh/boards/board-secureedge5410.c delete mode 100644 arch/sh/boards/mach-snapgear/Makefile delete mode 100644 arch/sh/boards/mach-snapgear/setup.c create mode 100644 arch/sh/configs/secureedge5410_defconfig delete mode 100644 arch/sh/configs/snapgear_defconfig create mode 100644 arch/sh/include/mach-common/mach/secureedge5410.h delete mode 100644 arch/sh/include/mach-common/mach/snapgear.h diff --git a/arch/sh/Makefile b/arch/sh/Makefile index 307b3a4..194afbf 100644 --- a/arch/sh/Makefile +++ b/arch/sh/Makefile @@ -133,7 +133,6 @@ machdir-$(CONFIG_SOLUTION_ENGINE) += mach-se machdir-$(CONFIG_SH_HP6XX) += mach-hp6xx machdir-$(CONFIG_SH_DREAMCAST) += mach-dreamcast machdir-$(CONFIG_SH_SH03) += mach-sh03 -machdir-$(CONFIG_SH_SECUREEDGE5410) += mach-snapgear machdir-$(CONFIG_SH_RTS7751R2D) += mach-r2d machdir-$(CONFIG_SH_7751_SYSTEMH) += mach-systemh machdir-$(CONFIG_SH_EDOSK7705) += mach-edosk7705 diff --git a/arch/sh/boards/Makefile b/arch/sh/boards/Makefile index 38ef655..4a0ed86 100644 --- a/arch/sh/boards/Makefile +++ b/arch/sh/boards/Makefile @@ -2,6 +2,7 @@ # Specific board support, not covered by a mach group. # obj-$(CONFIG_SH_MAGIC_PANEL_R2) += board-magicpanelr2.o +obj-$(CONFIG_SH_SECUREEDGE5410) += board-secureedge5410.o obj-$(CONFIG_SH_SH2007) += board-sh2007.o obj-$(CONFIG_SH_SH7785LCR) += board-sh7785lcr.o obj-$(CONFIG_SH_URQUELL) += board-urquell.o diff --git a/arch/sh/boards/board-secureedge5410.c b/arch/sh/boards/board-secureedge5410.c new file mode 100644 index 0000000..32f875e --- /dev/null +++ b/arch/sh/boards/board-secureedge5410.c @@ -0,0 +1,79 @@ +/* + * Copyright (C) 2002 David McCullough + * Copyright (C) 2003 Paul Mundt + * + * Based on files with the following comments: + * + * Copyright (C) 2000 Kazumoto Kojima + * + * Modified for 7751 Solution Engine by + * Ian da Silva and Jeremy Siegel, 2001. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +unsigned short secureedge5410_ioport; + +/* + * EraseConfig handling functions + */ +static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id) +{ + ctrl_delay(); /* dummy read */ + + printk("SnapGear: erase switch interrupt!\n"); + + return IRQ_HANDLED; +} + +static int __init eraseconfig_init(void) +{ + unsigned int irq = evt2irq(0x240); + + printk("SnapGear: EraseConfig init\n"); + + /* Setup "EraseConfig" switch on external IRQ 0 */ + if (request_irq(irq, eraseconfig_interrupt, IRQF_DISABLED, + "Erase Config", NULL)) + printk("SnapGear: failed to register IRQ%d for Reset witch\n", + irq); + else + printk("SnapGear: registered EraseConfig switch on IRQ%d\n", + irq); + return 0; +} +module_init(eraseconfig_init); + +/* + * Initialize IRQ setting + * + * IRL0 = erase switch + * IRL1 = eth0 + * IRL2 = eth1 + * IRL3 = crypto + */ +static void __init init_snapgear_IRQ(void) +{ + printk("Setup SnapGear IRQ/IPR ...\n"); + /* enable individual interrupt mode for externals */ + plat_irq_setup_pins(IRQ_MODE_IRQ); +} + +/* + * The Machine Vector + */ +static struct sh_machine_vector mv_snapgear __initmv = { + .mv_name = "SnapGear SecureEdge5410", + .mv_nr_irqs = 72, + .mv_init_irq = init_snapgear_IRQ, +}; diff --git a/arch/sh/boards/mach-snapgear/Makefile b/arch/sh/boards/mach-snapgear/Makefile deleted file mode 100644 index bc92e34..0000000 --- a/arch/sh/boards/mach-snapgear/Makefile +++ /dev/null @@ -1,5 +0,0 @@ -# -# Makefile for the SnapGear specific parts of the kernel -# - -obj-y := setup.o diff --git a/arch/sh/boards/mach-snapgear/setup.c b/arch/sh/boards/mach-snapgear/setup.c deleted file mode 100644 index 10eeea9..0000000 --- a/arch/sh/boards/mach-snapgear/setup.c +++ /dev/null @@ -1,79 +0,0 @@ -/* - * Copyright (C) 2002 David McCullough - * Copyright (C) 2003 Paul Mundt - * - * Based on files with the following comments: - * - * Copyright (C) 2000 Kazumoto Kojima - * - * Modified for 7751 Solution Engine by - * Ian da Silva and Jeremy Siegel, 2001. - */ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -unsigned short secureedge5410_ioport; - -/* - * EraseConfig handling functions - */ -static irqreturn_t eraseconfig_interrupt(int irq, void *dev_id) -{ - ctrl_delay(); /* dummy read */ - - printk("SnapGear: erase switch interrupt!\n"); - - return IRQ_HANDLED; -} - -static int __init eraseconfig_init(void) -{ - unsigned int irq = evt2irq(0x240); - - printk("SnapGear: EraseConfig init\n"); - - /* Setup "EraseConfig" switch on external IRQ 0 */ - if (request_irq(irq, eraseconfig_interrupt, IRQF_DISABLED, - "Erase Config", NULL)) - printk("SnapGear: failed to register IRQ%d for Reset witch\n", - irq); - else - printk("SnapGear: registered EraseConfig switch on IRQ%d\n", - irq); - return 0; -} -module_init(eraseconfig_init); - -/* - * Initialize IRQ setting - * - * IRL0 = erase switch - * IRL1 = eth0 - * IRL2 = eth1 - * IRL3 = crypto - */ -static void __init init_snapgear_IRQ(void) -{ - printk("Setup SnapGear IRQ/IPR ...\n"); - /* enable individual interrupt mode for externals */ - plat_irq_setup_pins(IRQ_MODE_IRQ); -} - -/* - * The Machine Vector - */ -static struct sh_machine_vector mv_snapgear __initmv = { - .mv_name = "SnapGear SecureEdge5410", - .mv_nr_irqs = 72, - .mv_init_irq = init_snapgear_IRQ, -}; diff --git a/arch/sh/configs/secureedge5410_defconfig b/arch/sh/configs/secureedge5410_defconfig new file mode 100644 index 0000000..7eae4e5 --- /dev/null +++ b/arch/sh/configs/secureedge5410_defconfig @@ -0,0 +1,63 @@ +CONFIG_EXPERIMENTAL=y +# CONFIG_SWAP is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_BLK_DEV_INITRD=y +# CONFIG_SYSCTL_SYSCALL is not set +# CONFIG_HOTPLUG is not set +CONFIG_SLAB=y +# CONFIG_BLK_DEV_BSG is not set +CONFIG_CPU_SUBTYPE_SH7751R=y +CONFIG_MEMORY_SIZE=0x01000000 +CONFIG_FLATMEM_MANUAL=y +CONFIG_SH_SECUREEDGE5410=y +CONFIG_SH_DMA=y +CONFIG_SH_DMA_API=y +CONFIG_PCI=y +CONFIG_NET=y +CONFIG_INET=y +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set +# CONFIG_INET_DIAG is not set +# CONFIG_IPV6 is not set +CONFIG_MTD=y +CONFIG_MTD_PARTITIONS=y +CONFIG_MTD_CHAR=y +CONFIG_MTD_BLOCK_RO=y +CONFIG_MTD_CFI=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_GEOMETRY=y +# CONFIG_MTD_MAP_BANK_WIDTH_2 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set +# CONFIG_MTD_CFI_I2 is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_PLATRAM=y +CONFIG_BLK_DEV_RAM=y +# CONFIG_MISC_DEVICES is not set +CONFIG_NETDEVICES=y +CONFIG_NET_ETHERNET=y +CONFIG_NET_PCI=y +CONFIG_8139CP=y +CONFIG_8139TOO=y +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_SERIO is not set +# CONFIG_VT is not set +CONFIG_SERIAL_SH_SCI=y +CONFIG_SERIAL_SH_SCI_CONSOLE=y +# CONFIG_HW_RANDOM is not set +# CONFIG_HWMON is not set +# CONFIG_HID_SUPPORT is not set +# CONFIG_USB_SUPPORT is not set +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_DS1302=y +CONFIG_EXT2_FS=y +# CONFIG_DNOTIFY is not set +CONFIG_TMPFS=y +CONFIG_CRAMFS=y +CONFIG_ROMFS_FS=y +# CONFIG_RCU_CPU_STALL_DETECTOR is not set diff --git a/arch/sh/configs/snapgear_defconfig b/arch/sh/configs/snapgear_defconfig deleted file mode 100644 index 7eae4e5..0000000 --- a/arch/sh/configs/snapgear_defconfig +++ /dev/null @@ -1,63 +0,0 @@ -CONFIG_EXPERIMENTAL=y -# CONFIG_SWAP is not set -CONFIG_LOG_BUF_SHIFT=14 -CONFIG_BLK_DEV_INITRD=y -# CONFIG_SYSCTL_SYSCALL is not set -# CONFIG_HOTPLUG is not set -CONFIG_SLAB=y -# CONFIG_BLK_DEV_BSG is not set -CONFIG_CPU_SUBTYPE_SH7751R=y -CONFIG_MEMORY_SIZE=0x01000000 -CONFIG_FLATMEM_MANUAL=y -CONFIG_SH_SECUREEDGE5410=y -CONFIG_SH_DMA=y -CONFIG_SH_DMA_API=y -CONFIG_PCI=y -CONFIG_NET=y -CONFIG_INET=y -# CONFIG_INET_XFRM_MODE_TRANSPORT is not set -# CONFIG_INET_XFRM_MODE_TUNNEL is not set -# CONFIG_INET_XFRM_MODE_BEET is not set -# CONFIG_INET_LRO is not set -# CONFIG_INET_DIAG is not set -# CONFIG_IPV6 is not set -CONFIG_MTD=y -CONFIG_MTD_PARTITIONS=y -CONFIG_MTD_CHAR=y -CONFIG_MTD_BLOCK_RO=y -CONFIG_MTD_CFI=y -CONFIG_MTD_CFI_ADV_OPTIONS=y -CONFIG_MTD_CFI_GEOMETRY=y -# CONFIG_MTD_MAP_BANK_WIDTH_2 is not set -# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set -# CONFIG_MTD_CFI_I2 is not set -CONFIG_MTD_CFI_INTELEXT=y -CONFIG_MTD_PLATRAM=y -CONFIG_BLK_DEV_RAM=y -# CONFIG_MISC_DEVICES is not set -CONFIG_NETDEVICES=y -CONFIG_NET_ETHERNET=y -CONFIG_NET_PCI=y -CONFIG_8139CP=y -CONFIG_8139TOO=y -# CONFIG_NETDEV_1000 is not set -# CONFIG_NETDEV_10000 is not set -# CONFIG_INPUT_MOUSEDEV is not set -# CONFIG_INPUT_KEYBOARD is not set -# CONFIG_INPUT_MOUSE is not set -# CONFIG_SERIO is not set -# CONFIG_VT is not set -CONFIG_SERIAL_SH_SCI=y -CONFIG_SERIAL_SH_SCI_CONSOLE=y -# CONFIG_HW_RANDOM is not set -# CONFIG_HWMON is not set -# CONFIG_HID_SUPPORT is not set -# CONFIG_USB_SUPPORT is not set -CONFIG_RTC_CLASS=y -CONFIG_RTC_DRV_DS1302=y -CONFIG_EXT2_FS=y -# CONFIG_DNOTIFY is not set -CONFIG_TMPFS=y -CONFIG_CRAMFS=y -CONFIG_ROMFS_FS=y -# CONFIG_RCU_CPU_STALL_DETECTOR is not set diff --git a/arch/sh/include/mach-common/mach/secureedge5410.h b/arch/sh/include/mach-common/mach/secureedge5410.h new file mode 100644 index 0000000..3653b9a4 --- /dev/null +++ b/arch/sh/include/mach-common/mach/secureedge5410.h @@ -0,0 +1,49 @@ +/* + * include/asm-sh/snapgear.h + * + * Modified version of io_se.h for the snapgear-specific functions. + * + * May be copied or modified under the terms of the GNU General Public + * License. See linux/COPYING for more information. + * + * IO functions for a SnapGear + */ + +#ifndef _ASM_SH_IO_SNAPGEAR_H +#define _ASM_SH_IO_SNAPGEAR_H + +#define __IO_PREFIX snapgear +#include + +/* + * We need to remember what was written to the ioport as some bits + * are shared with other functions and you cannot read back what was + * written :-| + * + * Bit Read Write + * ----------------------------------------------- + * D0 DCD on ttySC1 power + * D1 Reset Switch heatbeat + * D2 ttySC0 CTS (7100) LAN + * D3 - WAN + * D4 ttySC0 DCD (7100) CONSOLE + * D5 - ONLINE + * D6 - VPN + * D7 - DTR on ttySC1 + * D8 - ttySC0 RTS (7100) + * D9 - ttySC0 DTR (7100) + * D10 - RTC SCLK + * D11 RTC DATA RTC DATA + * D12 - RTS RESET + */ + +#define SECUREEDGE_IOPORT_ADDR ((volatile short *) 0xb0000000) +extern unsigned short secureedge5410_ioport; + +#define SECUREEDGE_WRITE_IOPORT(val, mask) (*SECUREEDGE_IOPORT_ADDR = \ + (secureedge5410_ioport = \ + ((secureedge5410_ioport & ~(mask)) | ((val) & (mask))))) +#define SECUREEDGE_READ_IOPORT() \ + ((*SECUREEDGE_IOPORT_ADDR&0x0817) | (secureedge5410_ioport&~0x0817)) + +#endif /* _ASM_SH_IO_SNAPGEAR_H */ diff --git a/arch/sh/include/mach-common/mach/snapgear.h b/arch/sh/include/mach-common/mach/snapgear.h deleted file mode 100644 index 3653b9a4..0000000 --- a/arch/sh/include/mach-common/mach/snapgear.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * include/asm-sh/snapgear.h - * - * Modified version of io_se.h for the snapgear-specific functions. - * - * May be copied or modified under the terms of the GNU General Public - * License. See linux/COPYING for more information. - * - * IO functions for a SnapGear - */ - -#ifndef _ASM_SH_IO_SNAPGEAR_H -#define _ASM_SH_IO_SNAPGEAR_H - -#define __IO_PREFIX snapgear -#include - -/* - * We need to remember what was written to the ioport as some bits - * are shared with other functions and you cannot read back what was - * written :-| - * - * Bit Read Write - * ----------------------------------------------- - * D0 DCD on ttySC1 power - * D1 Reset Switch heatbeat - * D2 ttySC0 CTS (7100) LAN - * D3 - WAN - * D4 ttySC0 DCD (7100) CONSOLE - * D5 - ONLINE - * D6 - VPN - * D7 - DTR on ttySC1 - * D8 - ttySC0 RTS (7100) - * D9 - ttySC0 DTR (7100) - * D10 - RTC SCLK - * D11 RTC DATA RTC DATA - * D12 - RTS RESET - */ - -#define SECUREEDGE_IOPORT_ADDR ((volatile short *) 0xb0000000) -extern unsigned short secureedge5410_ioport; - -#define SECUREEDGE_WRITE_IOPORT(val, mask) (*SECUREEDGE_IOPORT_ADDR = \ - (secureedge5410_ioport = \ - ((secureedge5410_ioport & ~(mask)) | ((val) & (mask))))) -#define SECUREEDGE_READ_IOPORT() \ - ((*SECUREEDGE_IOPORT_ADDR&0x0817) | (secureedge5410_ioport&~0x0817)) - -#endif /* _ASM_SH_IO_SNAPGEAR_H */ diff --git a/drivers/rtc/rtc-ds1302.c b/drivers/rtc/rtc-ds1302.c index 359d1e0..f0d6389 100644 --- a/drivers/rtc/rtc-ds1302.c +++ b/drivers/rtc/rtc-ds1302.c @@ -35,7 +35,7 @@ #ifdef CONFIG_SH_SECUREEDGE5410 #include -#include +#include #define RTC_RESET 0x1000 #define RTC_IODATA 0x0800 -- cgit v1.1 From 2504075d383fcefd746dac42a0cd1c3bdc006bd1 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Fri, 29 Oct 2010 19:11:56 +0900 Subject: sh: mach-systemh: Kill off dead board. This code has been untouched since it was merged many years ago, and has severely bitrotted since, suggesting that the board has no real users left. Notice of intent to remove has been sent out over the last few years, with no takers. Kill it off. Signed-off-by: Paul Mundt --- arch/sh/Makefile | 1 - arch/sh/boards/Kconfig | 7 -- arch/sh/boards/mach-systemh/Makefile | 13 -- arch/sh/boards/mach-systemh/io.c | 158 ------------------------- arch/sh/boards/mach-systemh/irq.c | 61 ---------- arch/sh/boards/mach-systemh/setup.c | 57 --------- arch/sh/configs/systemh_defconfig | 28 ----- arch/sh/include/mach-common/mach/systemh7751.h | 71 ----------- arch/sh/tools/mach-types | 1 - 9 files changed, 397 deletions(-) delete mode 100644 arch/sh/boards/mach-systemh/Makefile delete mode 100644 arch/sh/boards/mach-systemh/io.c delete mode 100644 arch/sh/boards/mach-systemh/irq.c delete mode 100644 arch/sh/boards/mach-systemh/setup.c delete mode 100644 arch/sh/configs/systemh_defconfig delete mode 100644 arch/sh/include/mach-common/mach/systemh7751.h diff --git a/arch/sh/Makefile b/arch/sh/Makefile index 194afbf..922ff35 100644 --- a/arch/sh/Makefile +++ b/arch/sh/Makefile @@ -134,7 +134,6 @@ machdir-$(CONFIG_SH_HP6XX) += mach-hp6xx machdir-$(CONFIG_SH_DREAMCAST) += mach-dreamcast machdir-$(CONFIG_SH_SH03) += mach-sh03 machdir-$(CONFIG_SH_RTS7751R2D) += mach-r2d -machdir-$(CONFIG_SH_7751_SYSTEMH) += mach-systemh machdir-$(CONFIG_SH_EDOSK7705) += mach-edosk7705 machdir-$(CONFIG_SH_HIGHLANDER) += mach-highlander machdir-$(CONFIG_SH_MIGOR) += mach-migor diff --git a/arch/sh/boards/Kconfig b/arch/sh/boards/Kconfig index 9c94711..2018c7e 100644 --- a/arch/sh/boards/Kconfig +++ b/arch/sh/boards/Kconfig @@ -81,13 +81,6 @@ config SH_7343_SOLUTION_ENGINE Select 7343 SolutionEngine if configuring for a Hitachi SH7343 (SH-Mobile 3AS) evaluation board. -config SH_7751_SYSTEMH - bool "SystemH7751R" - depends on CPU_SUBTYPE_SH7751R - help - Select SystemH if you are configuring for a Renesas SystemH - 7751R evaluation board. - config SH_HP6XX bool "HP6XX" select SYS_SUPPORTS_APM_EMULATION diff --git a/arch/sh/boards/mach-systemh/Makefile b/arch/sh/boards/mach-systemh/Makefile deleted file mode 100644 index 2cc6a23..0000000 --- a/arch/sh/boards/mach-systemh/Makefile +++ /dev/null @@ -1,13 +0,0 @@ -# -# Makefile for the SystemH specific parts of the kernel -# - -obj-y := setup.o irq.o io.o - -# XXX: This wants to be consolidated in arch/sh/drivers/pci, and more -# importantly, with the generic sh7751_pcic_init() code. For now, we'll -# just abuse the hell out of kbuild, because we can.. - -obj-$(CONFIG_PCI) += pci.o -pci-y := ../../se/7751/pci.o - diff --git a/arch/sh/boards/mach-systemh/io.c b/arch/sh/boards/mach-systemh/io.c deleted file mode 100644 index 15577ff..0000000 --- a/arch/sh/boards/mach-systemh/io.c +++ /dev/null @@ -1,158 +0,0 @@ -/* - * linux/arch/sh/boards/renesas/systemh/io.c - * - * Copyright (C) 2001 Ian da Silva, Jeremy Siegel - * Based largely on io_se.c. - * - * I/O routine for Hitachi 7751 Systemh. - */ -#include -#include -#include -#include -#include -#include - -#define ETHER_IOMAP(adr) (0xB3000000 + (adr)) /*map to 16bits access area - of smc lan chip*/ -static inline volatile __u16 * -port2adr(unsigned int port) -{ - if (port >= 0x2000) - return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000)); - maybebadio((unsigned long)port); - return (volatile __u16*)port; -} - -/* - * General outline: remap really low stuff [eventually] to SuperIO, - * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO) - * is mapped through the PCI IO window. Stuff with high bits (PXSEG) - * should be way beyond the window, and is used w/o translation for - * compatibility. - */ -unsigned char sh7751systemh_inb(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned char *)port; - else if (port <= 0x3F1) - return *(volatile unsigned char *)ETHER_IOMAP(port); - else - return (*port2adr(port))&0xff; -} - -unsigned char sh7751systemh_inb_p(unsigned long port) -{ - unsigned char v; - - if (PXSEG(port)) - v = *(volatile unsigned char *)port; - else if (port <= 0x3F1) - v = *(volatile unsigned char *)ETHER_IOMAP(port); - else - v = (*port2adr(port))&0xff; - ctrl_delay(); - return v; -} - -unsigned short sh7751systemh_inw(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned short *)port; - else if (port >= 0x2000) - return *port2adr(port); - else if (port <= 0x3F1) - return *(volatile unsigned int *)ETHER_IOMAP(port); - else - maybebadio(port); - return 0; -} - -unsigned int sh7751systemh_inl(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned long *)port; - else if (port >= 0x2000) - return *port2adr(port); - else if (port <= 0x3F1) - return *(volatile unsigned int *)ETHER_IOMAP(port); - else - maybebadio(port); - return 0; -} - -void sh7751systemh_outb(unsigned char value, unsigned long port) -{ - - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else if (port <= 0x3F1) - *(volatile unsigned char *)ETHER_IOMAP(port) = value; - else - *(port2adr(port)) = value; -} - -void sh7751systemh_outb_p(unsigned char value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else if (port <= 0x3F1) - *(volatile unsigned char *)ETHER_IOMAP(port) = value; - else - *(port2adr(port)) = value; - ctrl_delay(); -} - -void sh7751systemh_outw(unsigned short value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned short *)port = value; - else if (port >= 0x2000) - *port2adr(port) = value; - else if (port <= 0x3F1) - *(volatile unsigned short *)ETHER_IOMAP(port) = value; - else - maybebadio(port); -} - -void sh7751systemh_outl(unsigned int value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned long *)port = value; - else - maybebadio(port); -} - -void sh7751systemh_insb(unsigned long port, void *addr, unsigned long count) -{ - unsigned char *p = addr; - while (count--) *p++ = sh7751systemh_inb(port); -} - -void sh7751systemh_insw(unsigned long port, void *addr, unsigned long count) -{ - unsigned short *p = addr; - while (count--) *p++ = sh7751systemh_inw(port); -} - -void sh7751systemh_insl(unsigned long port, void *addr, unsigned long count) -{ - maybebadio(port); -} - -void sh7751systemh_outsb(unsigned long port, const void *addr, unsigned long count) -{ - unsigned char *p = (unsigned char*)addr; - while (count--) sh7751systemh_outb(*p++, port); -} - -void sh7751systemh_outsw(unsigned long port, const void *addr, unsigned long count) -{ - unsigned short *p = (unsigned short*)addr; - while (count--) sh7751systemh_outw(*p++, port); -} - -void sh7751systemh_outsl(unsigned long port, const void *addr, unsigned long count) -{ - maybebadio(port); -} diff --git a/arch/sh/boards/mach-systemh/irq.c b/arch/sh/boards/mach-systemh/irq.c deleted file mode 100644 index e5ee13a..0000000 --- a/arch/sh/boards/mach-systemh/irq.c +++ /dev/null @@ -1,61 +0,0 @@ -/* - * linux/arch/sh/boards/renesas/systemh/irq.c - * - * Copyright (C) 2000 Kazumoto Kojima - * - * Hitachi SystemH Support. - * - * Modified for 7751 SystemH by - * Jonathan Short. - */ - -#include -#include -#include -#include - -#include -#include - -/* address of external interrupt mask register - * address must be set prior to use these (maybe in init_XXX_irq()) - * XXX : is it better to use .config than specifying it in code? */ -static unsigned long *systemh_irq_mask_register = (unsigned long *)0xB3F10004; -static unsigned long *systemh_irq_request_register = (unsigned long *)0xB3F10000; - -static void disable_systemh_irq(struct irq_data *data) -{ - unsigned long val, mask = 0x01 << 1; - - /* Clear the "irq"th bit in the mask and set it in the request */ - val = __raw_readl((unsigned long)systemh_irq_mask_register); - val &= ~mask; - __raw_writel(val, (unsigned long)systemh_irq_mask_register); - - val = __raw_readl((unsigned long)systemh_irq_request_register); - val |= mask; - __raw_writel(val, (unsigned long)systemh_irq_request_register); -} - -static void enable_systemh_irq(struct irq_data *data) -{ - unsigned long val, mask = 0x01 << 1; - - /* Set "irq"th bit in the mask register */ - val = __raw_readl((unsigned long)systemh_irq_mask_register); - val |= mask; - __raw_writel(val, (unsigned long)systemh_irq_mask_register); -} - -static struct irq_chip systemh_irq_type = { - .name = "SystemH Register", - .irq_unmask = enable_systemh_irq, - .irq_mask = disable_systemh_irq, -}; - -void make_systemh_irq(unsigned int irq) -{ - disable_irq_nosync(irq); - set_irq_chip_and_handler(irq, &systemh_irq_type, handle_level_irq); - disable_systemh_irq(irq_get_irq_data(irq)); -} diff --git a/arch/sh/boards/mach-systemh/setup.c b/arch/sh/boards/mach-systemh/setup.c deleted file mode 100644 index 219fd80..0000000 --- a/arch/sh/boards/mach-systemh/setup.c +++ /dev/null @@ -1,57 +0,0 @@ -/* - * linux/arch/sh/boards/renesas/systemh/setup.c - * - * Copyright (C) 2000 Kazumoto Kojima - * Copyright (C) 2003 Paul Mundt - * - * Hitachi SystemH Support. - * - * Modified for 7751 SystemH by Jonathan Short. - * - * Rewritten for 2.6 by Paul Mundt. - * - * This file is subject to the terms and conditions of the GNU General Public - * License. See the file "COPYING" in the main directory of this archive - * for more details. - */ -#include -#include -#include - -extern void make_systemh_irq(unsigned int irq); - -/* - * Initialize IRQ setting - */ -static void __init sh7751systemh_init_irq(void) -{ - make_systemh_irq(0xb); /* Ethernet interrupt */ -} - -static struct sh_machine_vector mv_7751systemh __initmv = { - .mv_name = "7751 SystemH", - .mv_nr_irqs = 72, - - .mv_inb = sh7751systemh_inb, - .mv_inw = sh7751systemh_inw, - .mv_inl = sh7751systemh_inl, - .mv_outb = sh7751systemh_outb, - .mv_outw = sh7751systemh_outw, - .mv_outl = sh7751systemh_outl, - - .mv_inb_p = sh7751systemh_inb_p, - .mv_inw_p = sh7751systemh_inw, - .mv_inl_p = sh7751systemh_inl, - .mv_outb_p = sh7751systemh_outb_p, - .mv_outw_p = sh7751systemh_outw, - .mv_outl_p = sh7751systemh_outl, - - .mv_insb = sh7751systemh_insb, - .mv_insw = sh7751systemh_insw, - .mv_insl = sh7751systemh_insl, - .mv_outsb = sh7751systemh_outsb, - .mv_outsw = sh7751systemh_outsw, - .mv_outsl = sh7751systemh_outsl, - - .mv_init_irq = sh7751systemh_init_irq, -}; diff --git a/arch/sh/configs/systemh_defconfig b/arch/sh/configs/systemh_defconfig deleted file mode 100644 index b58dfc50..0000000 --- a/arch/sh/configs/systemh_defconfig +++ /dev/null @@ -1,28 +0,0 @@ -CONFIG_EXPERIMENTAL=y -CONFIG_LOG_BUF_SHIFT=14 -CONFIG_BLK_DEV_INITRD=y -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set -# CONFIG_SYSCTL_SYSCALL is not set -# CONFIG_HOTPLUG is not set -CONFIG_SLAB=y -CONFIG_MODULES=y -CONFIG_MODULE_UNLOAD=y -# CONFIG_BLK_DEV_BSG is not set -CONFIG_CPU_SUBTYPE_SH7751R=y -CONFIG_MEMORY_START=0x0c000000 -CONFIG_MEMORY_SIZE=0x00400000 -CONFIG_FLATMEM_MANUAL=y -CONFIG_SH_7751_SYSTEMH=y -CONFIG_PREEMPT=y -# CONFIG_STANDALONE is not set -CONFIG_BLK_DEV_RAM=y -CONFIG_BLK_DEV_RAM_SIZE=1024 -# CONFIG_INPUT is not set -# CONFIG_SERIO_SERPORT is not set -# CONFIG_VT is not set -CONFIG_HW_RANDOM=y -CONFIG_PROC_KCORE=y -CONFIG_TMPFS=y -CONFIG_CRAMFS=y -CONFIG_ROMFS_FS=y -# CONFIG_RCU_CPU_STALL_DETECTOR is not set diff --git a/arch/sh/include/mach-common/mach/systemh7751.h b/arch/sh/include/mach-common/mach/systemh7751.h deleted file mode 100644 index 4161122..0000000 --- a/arch/sh/include/mach-common/mach/systemh7751.h +++ /dev/null @@ -1,71 +0,0 @@ -#ifndef __ASM_SH_SYSTEMH_7751SYSTEMH_H -#define __ASM_SH_SYSTEMH_7751SYSTEMH_H - -/* - * linux/include/asm-sh/systemh/7751systemh.h - * - * Copyright (C) 2000 Kazumoto Kojima - * - * Hitachi SystemH support - - * Modified for 7751 SystemH by - * Jonathan Short, 2002. - */ - -/* Box specific addresses. */ - -#define PA_ROM 0x00000000 /* EPROM */ -#define PA_ROM_SIZE 0x00400000 /* EPROM size 4M byte */ -#define PA_FROM 0x01000000 /* EPROM */ -#define PA_FROM_SIZE 0x00400000 /* EPROM size 4M byte */ -#define PA_EXT1 0x04000000 -#define PA_EXT1_SIZE 0x04000000 -#define PA_EXT2 0x08000000 -#define PA_EXT2_SIZE 0x04000000 -#define PA_SDRAM 0x0c000000 -#define PA_SDRAM_SIZE 0x04000000 - -#define PA_EXT4 0x12000000 -#define PA_EXT4_SIZE 0x02000000 -#define PA_EXT5 0x14000000 -#define PA_EXT5_SIZE 0x04000000 -#define PA_PCIC 0x18000000 /* MR-SHPC-01 PCMCIA */ - -#define PA_DIPSW0 0xb9000000 /* Dip switch 5,6 */ -#define PA_DIPSW1 0xb9000002 /* Dip switch 7,8 */ -#define PA_LED 0xba000000 /* LED */ -#define PA_BCR 0xbb000000 /* FPGA on the MS7751SE01 */ - -#define PA_MRSHPC 0xb83fffe0 /* MR-SHPC-01 PCMCIA controller */ -#define PA_MRSHPC_MW1 0xb8400000 /* MR-SHPC-01 memory window base */ -#define PA_MRSHPC_MW2 0xb8500000 /* MR-SHPC-01 attribute window base */ -#define PA_MRSHPC_IO 0xb8600000 /* MR-SHPC-01 I/O window base */ -#define MRSHPC_MODE (PA_MRSHPC + 4) -#define MRSHPC_OPTION (PA_MRSHPC + 6) -#define MRSHPC_CSR (PA_MRSHPC + 8) -#define MRSHPC_ISR (PA_MRSHPC + 10) -#define MRSHPC_ICR (PA_MRSHPC + 12) -#define MRSHPC_CPWCR (PA_MRSHPC + 14) -#define MRSHPC_MW0CR1 (PA_MRSHPC + 16) -#define MRSHPC_MW1CR1 (PA_MRSHPC + 18) -#define MRSHPC_IOWCR1 (PA_MRSHPC + 20) -#define MRSHPC_MW0CR2 (PA_MRSHPC + 22) -#define MRSHPC_MW1CR2 (PA_MRSHPC + 24) -#define MRSHPC_IOWCR2 (PA_MRSHPC + 26) -#define MRSHPC_CDCR (PA_MRSHPC + 28) -#define MRSHPC_PCIC_INFO (PA_MRSHPC + 30) - -#define BCR_ILCRA (PA_BCR + 0) -#define BCR_ILCRB (PA_BCR + 2) -#define BCR_ILCRC (PA_BCR + 4) -#define BCR_ILCRD (PA_BCR + 6) -#define BCR_ILCRE (PA_BCR + 8) -#define BCR_ILCRF (PA_BCR + 10) -#define BCR_ILCRG (PA_BCR + 12) - -#define IRQ_79C973 13 - -#define __IO_PREFIX sh7751systemh -#include - -#endif /* __ASM_SH_SYSTEMH_7751SYSTEMH_H */ diff --git a/arch/sh/tools/mach-types b/arch/sh/tools/mach-types index 9f56eb9..0e68465 100644 --- a/arch/sh/tools/mach-types +++ b/arch/sh/tools/mach-types @@ -26,7 +26,6 @@ HD64461 HD64461 7724SE SH_7724_SOLUTION_ENGINE 7751SE SH_7751_SOLUTION_ENGINE 7780SE SH_7780_SOLUTION_ENGINE -7751SYSTEMH SH_7751_SYSTEMH HP6XX SH_HP6XX DREAMCAST SH_DREAMCAST SNAPGEAR SH_SECUREEDGE5410 -- cgit v1.1 From db2d0373fd1fe4db94587d52767388d811ee201f Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Fri, 29 Oct 2010 19:24:59 +0900 Subject: sh: mach-se: Rip out superfluous 7206 PIO routines. The PIO trapping was only for MRSHPC and the SMC ethernet. Given that the SMC ethernet is already properly handled and that nothing is using the MRSHPC, none of this is needed. Signed-off-by: Paul Mundt --- arch/sh/boards/mach-se/7206/Makefile | 2 +- arch/sh/boards/mach-se/7206/io.c | 104 ----------------------------------- arch/sh/boards/mach-se/7206/setup.c | 15 ----- 3 files changed, 1 insertion(+), 120 deletions(-) delete mode 100644 arch/sh/boards/mach-se/7206/io.c diff --git a/arch/sh/boards/mach-se/7206/Makefile b/arch/sh/boards/mach-se/7206/Makefile index 63e7ed6..5c9eaa0 100644 --- a/arch/sh/boards/mach-se/7206/Makefile +++ b/arch/sh/boards/mach-se/7206/Makefile @@ -2,4 +2,4 @@ # Makefile for the 7206 SolutionEngine specific parts of the kernel # -obj-y := setup.o io.o irq.o +obj-y := setup.o irq.o diff --git a/arch/sh/boards/mach-se/7206/io.c b/arch/sh/boards/mach-se/7206/io.c deleted file mode 100644 index adadc77..0000000 --- a/arch/sh/boards/mach-se/7206/io.c +++ /dev/null @@ -1,104 +0,0 @@ -/* $Id: io.c,v 1.5 2004/02/22 23:08:43 kkojima Exp $ - * - * linux/arch/sh/boards/se/7206/io.c - * - * Copyright (C) 2006 Yoshinori Sato - * - * I/O routine for Hitachi 7206 SolutionEngine. - * - */ - -#include -#include -#include -#include - - -static inline void delay(void) -{ - __raw_readw(0x20000000); /* P2 ROM Area */ -} - -/* MS7750 requires special versions of in*, out* routines, since - PC-like io ports are located at upper half byte of 16-bit word which - can be accessed only with 16-bit wide. */ - -static inline volatile __u16 * -port2adr(unsigned int port) -{ - if (port >= 0x2000 && port < 0x2020) - return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000)); - else if (port >= 0x300 && port < 0x310) - return (volatile __u16 *) (PA_SMSC + (port - 0x300)); - - return (volatile __u16 *)port; -} - -unsigned char se7206_inb(unsigned long port) -{ - return (*port2adr(port)) & 0xff; -} - -unsigned char se7206_inb_p(unsigned long port) -{ - unsigned long v; - - v = (*port2adr(port)) & 0xff; - delay(); - return v; -} - -unsigned short se7206_inw(unsigned long port) -{ - return *port2adr(port); -} - -void se7206_outb(unsigned char value, unsigned long port) -{ - *(port2adr(port)) = value; -} - -void se7206_outb_p(unsigned char value, unsigned long port) -{ - *(port2adr(port)) = value; - delay(); -} - -void se7206_outw(unsigned short value, unsigned long port) -{ - *port2adr(port) = value; -} - -void se7206_insb(unsigned long port, void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - __u8 *ap = addr; - - while (count--) - *ap++ = *p; -} - -void se7206_insw(unsigned long port, void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - __u16 *ap = addr; - while (count--) - *ap++ = *p; -} - -void se7206_outsb(unsigned long port, const void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - const __u8 *ap = addr; - - while (count--) - *p = *ap++; -} - -void se7206_outsw(unsigned long port, const void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - const __u16 *ap = addr; - while (count--) - *p = *ap++; -} diff --git a/arch/sh/boards/mach-se/7206/setup.c b/arch/sh/boards/mach-se/7206/setup.c index 8f5c65d..7f4871c 100644 --- a/arch/sh/boards/mach-se/7206/setup.c +++ b/arch/sh/boards/mach-se/7206/setup.c @@ -86,20 +86,5 @@ __initcall(se7206_devices_setup); static struct sh_machine_vector mv_se __initmv = { .mv_name = "SolutionEngine", .mv_nr_irqs = 256, - .mv_inb = se7206_inb, - .mv_inw = se7206_inw, - .mv_outb = se7206_outb, - .mv_outw = se7206_outw, - - .mv_inb_p = se7206_inb_p, - .mv_inw_p = se7206_inw, - .mv_outb_p = se7206_outb_p, - .mv_outw_p = se7206_outw, - - .mv_insb = se7206_insb, - .mv_insw = se7206_insw, - .mv_outsb = se7206_outsb, - .mv_outsw = se7206_outsw, - .mv_init_irq = init_se7206_IRQ, }; -- cgit v1.1 From c1cfed3c3a190b4ce1d5a4510d9dfd3d42176fba Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Fri, 29 Oct 2010 19:34:13 +0900 Subject: sh: mach-edosk7705: update for this century, kill off PIO trapping. The only reason this board needs to do PIO trapping is for ethernet, which happens to follow the same scheme as its bigger brother the edosk7760. With ethernet properly supported through the platform device, we can kill off the left over PIO abortion. Signed-off-by: Paul Mundt --- arch/sh/boards/mach-edosk7705/Makefile | 2 +- arch/sh/boards/mach-edosk7705/io.c | 71 ---------------------------------- arch/sh/boards/mach-edosk7705/setup.c | 63 +++++++++++++++++++++++++----- 3 files changed, 54 insertions(+), 82 deletions(-) delete mode 100644 arch/sh/boards/mach-edosk7705/io.c diff --git a/arch/sh/boards/mach-edosk7705/Makefile b/arch/sh/boards/mach-edosk7705/Makefile index cd54acb..0cf5715 100644 --- a/arch/sh/boards/mach-edosk7705/Makefile +++ b/arch/sh/boards/mach-edosk7705/Makefile @@ -2,4 +2,4 @@ # Makefile for the EDOSK7705 specific parts of the kernel # -obj-y := setup.o io.o +obj-y := setup.o diff --git a/arch/sh/boards/mach-edosk7705/io.c b/arch/sh/boards/mach-edosk7705/io.c deleted file mode 100644 index 5b9c57c..0000000 --- a/arch/sh/boards/mach-edosk7705/io.c +++ /dev/null @@ -1,71 +0,0 @@ -/* - * arch/sh/boards/renesas/edosk7705/io.c - * - * Copyright (C) 2001 Ian da Silva, Jeremy Siegel - * Based largely on io_se.c. - * - * I/O routines for Hitachi EDOSK7705 board. - * - */ - -#include -#include -#include -#include -#include - -#define SMC_IOADDR 0xA2000000 - -/* Map the Ethernet addresses as if it is at 0x300 - 0x320 */ -static unsigned long sh_edosk7705_isa_port2addr(unsigned long port) -{ - /* - * SMC91C96 registers are 4 byte aligned rather than the - * usual 2 byte! - */ - if (port >= 0x300 && port < 0x320) - return SMC_IOADDR + ((port - 0x300) * 2); - - maybebadio(port); - return port; -} - -/* Trying to read / write bytes on odd-byte boundaries to the Ethernet - * registers causes problems. So we bit-shift the value and read / write - * in 2 byte chunks. Setting the low byte to 0 does not cause problems - * now as odd byte writes are only made on the bit mask / interrupt - * register. This may not be the case in future Mar-2003 SJD - */ -unsigned char sh_edosk7705_inb(unsigned long port) -{ - if (port >= 0x300 && port < 0x320 && port & 0x01) - return __raw_readw(port - 1) >> 8; - - return __raw_readb(sh_edosk7705_isa_port2addr(port)); -} - -void sh_edosk7705_outb(unsigned char value, unsigned long port) -{ - if (port >= 0x300 && port < 0x320 && port & 0x01) { - __raw_writew(((unsigned short)value << 8), port - 1); - return; - } - - __raw_writeb(value, sh_edosk7705_isa_port2addr(port)); -} - -void sh_edosk7705_insb(unsigned long port, void *addr, unsigned long count) -{ - unsigned char *p = addr; - - while (count--) - *p++ = sh_edosk7705_inb(port); -} - -void sh_edosk7705_outsb(unsigned long port, const void *addr, unsigned long count) -{ - unsigned char *p = (unsigned char *)addr; - - while (count--) - sh_edosk7705_outb(*p++, port); -} diff --git a/arch/sh/boards/mach-edosk7705/setup.c b/arch/sh/boards/mach-edosk7705/setup.c index d59225e..8f93b66 100644 --- a/arch/sh/boards/mach-edosk7705/setup.c +++ b/arch/sh/boards/mach-edosk7705/setup.c @@ -10,27 +10,70 @@ */ #include #include -#include +#include +#include +#include #include +#include +#include + +#define SMC_IOBASE 0xA2000000 +#define SMC_IO_OFFSET 0x300 +#define SMC_IOADDR (SMC_IOBASE + SMC_IO_OFFSET) + +#define ETHERNET_IRQ 0x09 static void __init sh_edosk7705_init_irq(void) { - /* This is the Ethernet interrupt */ - make_imask_irq(0x09); + make_imask_irq(ETHERNET_IRQ); } +/* eth initialization functions */ +static struct smc91x_platdata smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_IO_SHIFT_1 | IORESOURCE_IRQ_LOWLEVEL, +}; + +static struct resource smc91x_res[] = { + [0] = { + .start = SMC_IOADDR, + .end = SMC_IOADDR + SZ_32 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = ETHERNET_IRQ, + .end = ETHERNET_IRQ, + .flags = IORESOURCE_IRQ , + } +}; + +static struct platform_device smc91x_dev = { + .name = "smc91x", + .id = -1, + .num_resources = ARRAY_SIZE(smc91x_res), + .resource = smc91x_res, + + .dev = { + .platform_data = &smc91x_info, + }, +}; + +/* platform init code */ +static struct platform_device *edosk7705_devices[] __initdata = { + &smc91x_dev, +}; + +static int __init init_edosk7705_devices(void) +{ + return platform_add_devices(edosk7705_devices, + ARRAY_SIZE(edosk7705_devices)); +} +__initcall(init_edosk7705_devices); + /* * The Machine Vector */ static struct sh_machine_vector mv_edosk7705 __initmv = { .mv_name = "EDOSK7705", .mv_nr_irqs = 80, - - .mv_inb = sh_edosk7705_inb, - .mv_outb = sh_edosk7705_outb, - - .mv_insb = sh_edosk7705_insb, - .mv_outsb = sh_edosk7705_outsb, - .mv_init_irq = sh_edosk7705_init_irq, }; -- cgit v1.1 From c819cc732267d6e46833a8d98bd7677b3d12d7d1 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Fri, 29 Oct 2010 19:38:19 +0900 Subject: sh: mach-edosk7705: Kill off machtype, consolidate board def. Trivial shuffling and tidying. Signed-off-by: Paul Mundt --- arch/sh/Makefile | 1 - arch/sh/boards/Makefile | 1 + arch/sh/boards/board-edosk7705.c | 78 +++++++++++++++++++++++++++ arch/sh/boards/mach-edosk7705/Makefile | 5 -- arch/sh/boards/mach-edosk7705/setup.c | 79 ---------------------------- arch/sh/include/mach-common/mach/edosk7705.h | 7 --- 6 files changed, 79 insertions(+), 92 deletions(-) create mode 100644 arch/sh/boards/board-edosk7705.c delete mode 100644 arch/sh/boards/mach-edosk7705/Makefile delete mode 100644 arch/sh/boards/mach-edosk7705/setup.c delete mode 100644 arch/sh/include/mach-common/mach/edosk7705.h diff --git a/arch/sh/Makefile b/arch/sh/Makefile index 922ff35..9c8c6e1 100644 --- a/arch/sh/Makefile +++ b/arch/sh/Makefile @@ -134,7 +134,6 @@ machdir-$(CONFIG_SH_HP6XX) += mach-hp6xx machdir-$(CONFIG_SH_DREAMCAST) += mach-dreamcast machdir-$(CONFIG_SH_SH03) += mach-sh03 machdir-$(CONFIG_SH_RTS7751R2D) += mach-r2d -machdir-$(CONFIG_SH_EDOSK7705) += mach-edosk7705 machdir-$(CONFIG_SH_HIGHLANDER) += mach-highlander machdir-$(CONFIG_SH_MIGOR) += mach-migor machdir-$(CONFIG_SH_AP325RXA) += mach-ap325rxa diff --git a/arch/sh/boards/Makefile b/arch/sh/boards/Makefile index 4a0ed86..be7d11d 100644 --- a/arch/sh/boards/Makefile +++ b/arch/sh/boards/Makefile @@ -7,6 +7,7 @@ obj-$(CONFIG_SH_SH2007) += board-sh2007.o obj-$(CONFIG_SH_SH7785LCR) += board-sh7785lcr.o obj-$(CONFIG_SH_URQUELL) += board-urquell.o obj-$(CONFIG_SH_SHMIN) += board-shmin.o +obj-$(CONFIG_SH_EDOSK7705) += board-edosk7705.o obj-$(CONFIG_SH_EDOSK7760) += board-edosk7760.o obj-$(CONFIG_SH_ESPT) += board-espt.o obj-$(CONFIG_SH_POLARIS) += board-polaris.o diff --git a/arch/sh/boards/board-edosk7705.c b/arch/sh/boards/board-edosk7705.c new file mode 100644 index 0000000..4cb3bb7 --- /dev/null +++ b/arch/sh/boards/board-edosk7705.c @@ -0,0 +1,78 @@ +/* + * arch/sh/boards/renesas/edosk7705/setup.c + * + * Copyright (C) 2000 Kazumoto Kojima + * + * Hitachi SolutionEngine Support. + * + * Modified for edosk7705 development + * board by S. Dunn, 2003. + */ +#include +#include +#include +#include +#include +#include +#include + +#define SMC_IOBASE 0xA2000000 +#define SMC_IO_OFFSET 0x300 +#define SMC_IOADDR (SMC_IOBASE + SMC_IO_OFFSET) + +#define ETHERNET_IRQ 0x09 + +static void __init sh_edosk7705_init_irq(void) +{ + make_imask_irq(ETHERNET_IRQ); +} + +/* eth initialization functions */ +static struct smc91x_platdata smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_IO_SHIFT_1 | IORESOURCE_IRQ_LOWLEVEL, +}; + +static struct resource smc91x_res[] = { + [0] = { + .start = SMC_IOADDR, + .end = SMC_IOADDR + SZ_32 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = ETHERNET_IRQ, + .end = ETHERNET_IRQ, + .flags = IORESOURCE_IRQ , + } +}; + +static struct platform_device smc91x_dev = { + .name = "smc91x", + .id = -1, + .num_resources = ARRAY_SIZE(smc91x_res), + .resource = smc91x_res, + + .dev = { + .platform_data = &smc91x_info, + }, +}; + +/* platform init code */ +static struct platform_device *edosk7705_devices[] __initdata = { + &smc91x_dev, +}; + +static int __init init_edosk7705_devices(void) +{ + return platform_add_devices(edosk7705_devices, + ARRAY_SIZE(edosk7705_devices)); +} +__initcall(init_edosk7705_devices); + +/* + * The Machine Vector + */ +static struct sh_machine_vector mv_edosk7705 __initmv = { + .mv_name = "EDOSK7705", + .mv_nr_irqs = 80, + .mv_init_irq = sh_edosk7705_init_irq, +}; diff --git a/arch/sh/boards/mach-edosk7705/Makefile b/arch/sh/boards/mach-edosk7705/Makefile deleted file mode 100644 index 0cf5715..0000000 --- a/arch/sh/boards/mach-edosk7705/Makefile +++ /dev/null @@ -1,5 +0,0 @@ -# -# Makefile for the EDOSK7705 specific parts of the kernel -# - -obj-y := setup.o diff --git a/arch/sh/boards/mach-edosk7705/setup.c b/arch/sh/boards/mach-edosk7705/setup.c deleted file mode 100644 index 8f93b66..0000000 --- a/arch/sh/boards/mach-edosk7705/setup.c +++ /dev/null @@ -1,79 +0,0 @@ -/* - * arch/sh/boards/renesas/edosk7705/setup.c - * - * Copyright (C) 2000 Kazumoto Kojima - * - * Hitachi SolutionEngine Support. - * - * Modified for edosk7705 development - * board by S. Dunn, 2003. - */ -#include -#include -#include -#include -#include -#include -#include -#include - -#define SMC_IOBASE 0xA2000000 -#define SMC_IO_OFFSET 0x300 -#define SMC_IOADDR (SMC_IOBASE + SMC_IO_OFFSET) - -#define ETHERNET_IRQ 0x09 - -static void __init sh_edosk7705_init_irq(void) -{ - make_imask_irq(ETHERNET_IRQ); -} - -/* eth initialization functions */ -static struct smc91x_platdata smc91x_info = { - .flags = SMC91X_USE_16BIT | SMC91X_IO_SHIFT_1 | IORESOURCE_IRQ_LOWLEVEL, -}; - -static struct resource smc91x_res[] = { - [0] = { - .start = SMC_IOADDR, - .end = SMC_IOADDR + SZ_32 - 1, - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = ETHERNET_IRQ, - .end = ETHERNET_IRQ, - .flags = IORESOURCE_IRQ , - } -}; - -static struct platform_device smc91x_dev = { - .name = "smc91x", - .id = -1, - .num_resources = ARRAY_SIZE(smc91x_res), - .resource = smc91x_res, - - .dev = { - .platform_data = &smc91x_info, - }, -}; - -/* platform init code */ -static struct platform_device *edosk7705_devices[] __initdata = { - &smc91x_dev, -}; - -static int __init init_edosk7705_devices(void) -{ - return platform_add_devices(edosk7705_devices, - ARRAY_SIZE(edosk7705_devices)); -} -__initcall(init_edosk7705_devices); - -/* - * The Machine Vector - */ -static struct sh_machine_vector mv_edosk7705 __initmv = { - .mv_name = "EDOSK7705", - .mv_nr_irqs = 80, - .mv_init_irq = sh_edosk7705_init_irq, -}; diff --git a/arch/sh/include/mach-common/mach/edosk7705.h b/arch/sh/include/mach-common/mach/edosk7705.h deleted file mode 100644 index efc43b32..0000000 --- a/arch/sh/include/mach-common/mach/edosk7705.h +++ /dev/null @@ -1,7 +0,0 @@ -#ifndef __ASM_SH_EDOSK7705_H -#define __ASM_SH_EDOSK7705_H - -#define __IO_PREFIX sh_edosk7705 -#include - -#endif /* __ASM_SH_EDOSK7705_H */ -- cgit v1.1 From 1e789887f3449661be9826f61d48018a1cfcbfcc Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Fri, 29 Oct 2010 19:48:21 +0900 Subject: sh: mach-se: Rip out superfluous 770x PIO routines. Platform data takes care of all of these these days, kill them off. Signed-off-by: Paul Mundt --- arch/sh/boards/mach-se/770x/Makefile | 2 +- arch/sh/boards/mach-se/770x/io.c | 156 ----------------------------------- arch/sh/boards/mach-se/770x/setup.c | 22 ----- 3 files changed, 1 insertion(+), 179 deletions(-) delete mode 100644 arch/sh/boards/mach-se/770x/io.c diff --git a/arch/sh/boards/mach-se/770x/Makefile b/arch/sh/boards/mach-se/770x/Makefile index 8e624b0..43ea14f 100644 --- a/arch/sh/boards/mach-se/770x/Makefile +++ b/arch/sh/boards/mach-se/770x/Makefile @@ -2,4 +2,4 @@ # Makefile for the 770x SolutionEngine specific parts of the kernel # -obj-y := setup.o io.o irq.o +obj-y := setup.o irq.o diff --git a/arch/sh/boards/mach-se/770x/io.c b/arch/sh/boards/mach-se/770x/io.c deleted file mode 100644 index 28833c8..0000000 --- a/arch/sh/boards/mach-se/770x/io.c +++ /dev/null @@ -1,156 +0,0 @@ -/* - * Copyright (C) 2000 Kazumoto Kojima - * - * I/O routine for Hitachi SolutionEngine. - */ -#include -#include -#include -#include - -/* MS7750 requires special versions of in*, out* routines, since - PC-like io ports are located at upper half byte of 16-bit word which - can be accessed only with 16-bit wide. */ - -static inline volatile __u16 * -port2adr(unsigned int port) -{ - if (port & 0xff000000) - return ( volatile __u16 *) port; - if (port >= 0x2000) - return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000)); - else if (port >= 0x1000) - return (volatile __u16 *) (PA_83902 + (port << 1)); - else - return (volatile __u16 *) (PA_SUPERIO + (port << 1)); -} - -static inline int -shifted_port(unsigned long port) -{ - /* For IDE registers, value is not shifted */ - if ((0x1f0 <= port && port < 0x1f8) || port == 0x3f6) - return 0; - else - return 1; -} - -unsigned char se_inb(unsigned long port) -{ - if (shifted_port(port)) - return (*port2adr(port) >> 8); - else - return (*port2adr(port))&0xff; -} - -unsigned char se_inb_p(unsigned long port) -{ - unsigned long v; - - if (shifted_port(port)) - v = (*port2adr(port) >> 8); - else - v = (*port2adr(port))&0xff; - ctrl_delay(); - return v; -} - -unsigned short se_inw(unsigned long port) -{ - if (port >= 0x2000) - return *port2adr(port); - else - maybebadio(port); - return 0; -} - -unsigned int se_inl(unsigned long port) -{ - maybebadio(port); - return 0; -} - -void se_outb(unsigned char value, unsigned long port) -{ - if (shifted_port(port)) - *(port2adr(port)) = value << 8; - else - *(port2adr(port)) = value; -} - -void se_outb_p(unsigned char value, unsigned long port) -{ - if (shifted_port(port)) - *(port2adr(port)) = value << 8; - else - *(port2adr(port)) = value; - ctrl_delay(); -} - -void se_outw(unsigned short value, unsigned long port) -{ - if (port >= 0x2000) - *port2adr(port) = value; - else - maybebadio(port); -} - -void se_outl(unsigned int value, unsigned long port) -{ - maybebadio(port); -} - -void se_insb(unsigned long port, void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - __u8 *ap = addr; - - if (shifted_port(port)) { - while (count--) - *ap++ = *p >> 8; - } else { - while (count--) - *ap++ = *p; - } -} - -void se_insw(unsigned long port, void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - __u16 *ap = addr; - while (count--) - *ap++ = *p; -} - -void se_insl(unsigned long port, void *addr, unsigned long count) -{ - maybebadio(port); -} - -void se_outsb(unsigned long port, const void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - const __u8 *ap = addr; - - if (shifted_port(port)) { - while (count--) - *p = *ap++ << 8; - } else { - while (count--) - *p = *ap++; - } -} - -void se_outsw(unsigned long port, const void *addr, unsigned long count) -{ - volatile __u16 *p = port2adr(port); - const __u16 *ap = addr; - - while (count--) - *p = *ap++; -} - -void se_outsl(unsigned long port, const void *addr, unsigned long count) -{ - maybebadio(port); -} diff --git a/arch/sh/boards/mach-se/770x/setup.c b/arch/sh/boards/mach-se/770x/setup.c index 66d39d1..31330c6 100644 --- a/arch/sh/boards/mach-se/770x/setup.c +++ b/arch/sh/boards/mach-se/770x/setup.c @@ -195,27 +195,5 @@ static struct sh_machine_vector mv_se __initmv = { #elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712) .mv_nr_irqs = 104, #endif - - .mv_inb = se_inb, - .mv_inw = se_inw, - .mv_inl = se_inl, - .mv_outb = se_outb, - .mv_outw = se_outw, - .mv_outl = se_outl, - - .mv_inb_p = se_inb_p, - .mv_inw_p = se_inw, - .mv_inl_p = se_inl, - .mv_outb_p = se_outb_p, - .mv_outw_p = se_outw, - .mv_outl_p = se_outl, - - .mv_insb = se_insb, - .mv_insw = se_insw, - .mv_insl = se_insl, - .mv_outsb = se_outsb, - .mv_outsw = se_outsw, - .mv_outsl = se_outsl, - .mv_init_irq = init_se_IRQ, }; -- cgit v1.1 From e2781ac2a63011dd883e94c07eb086e6f2a5f521 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Fri, 29 Oct 2010 19:52:07 +0900 Subject: sh: mach-se: Rip out superfluous 7751 PIO routines. MRSHPC is wholly unused here, no need to trap it specially. If support is added in the future it can be taken care of via platform data like on the others. Signed-off-by: Paul Mundt --- arch/sh/boards/mach-se/7751/Makefile | 2 +- arch/sh/boards/mach-se/7751/io.c | 119 ----------------------------------- arch/sh/boards/mach-se/7751/setup.c | 18 ------ 3 files changed, 1 insertion(+), 138 deletions(-) delete mode 100644 arch/sh/boards/mach-se/7751/io.c diff --git a/arch/sh/boards/mach-se/7751/Makefile b/arch/sh/boards/mach-se/7751/Makefile index e6f4341..a338fd9 100644 --- a/arch/sh/boards/mach-se/7751/Makefile +++ b/arch/sh/boards/mach-se/7751/Makefile @@ -2,4 +2,4 @@ # Makefile for the 7751 SolutionEngine specific parts of the kernel # -obj-y := setup.o io.o irq.o +obj-y := setup.o irq.o diff --git a/arch/sh/boards/mach-se/7751/io.c b/arch/sh/boards/mach-se/7751/io.c deleted file mode 100644 index 6e75bd4..0000000 --- a/arch/sh/boards/mach-se/7751/io.c +++ /dev/null @@ -1,119 +0,0 @@ -/* - * Copyright (C) 2001 Ian da Silva, Jeremy Siegel - * Based largely on io_se.c. - * - * I/O routine for Hitachi 7751 SolutionEngine. - * - * Initial version only to support LAN access; some - * placeholder code from io_se.c left in with the - * expectation of later SuperIO and PCMCIA access. - */ -#include -#include -#include -#include -#include -#include - -static inline volatile u16 *port2adr(unsigned int port) -{ - if (port >= 0x2000) - return (volatile __u16 *) (PA_MRSHPC + (port - 0x2000)); - maybebadio((unsigned long)port); - return (volatile __u16*)port; -} - -/* - * General outline: remap really low stuff [eventually] to SuperIO, - * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO) - * is mapped through the PCI IO window. Stuff with high bits (PXSEG) - * should be way beyond the window, and is used w/o translation for - * compatibility. - */ -unsigned char sh7751se_inb(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned char *)port; - else - return (*port2adr(port)) & 0xff; -} - -unsigned char sh7751se_inb_p(unsigned long port) -{ - unsigned char v; - - if (PXSEG(port)) - v = *(volatile unsigned char *)port; - else - v = (*port2adr(port)) & 0xff; - ctrl_delay(); - return v; -} - -unsigned short sh7751se_inw(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned short *)port; - else if (port >= 0x2000) - return *port2adr(port); - else - maybebadio(port); - return 0; -} - -unsigned int sh7751se_inl(unsigned long port) -{ - if (PXSEG(port)) - return *(volatile unsigned long *)port; - else if (port >= 0x2000) - return *port2adr(port); - else - maybebadio(port); - return 0; -} - -void sh7751se_outb(unsigned char value, unsigned long port) -{ - - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else - *(port2adr(port)) = value; -} - -void sh7751se_outb_p(unsigned char value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned char *)port = value; - else - *(port2adr(port)) = value; - ctrl_delay(); -} - -void sh7751se_outw(unsigned short value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned short *)port = value; - else if (port >= 0x2000) - *port2adr(port) = value; - else - maybebadio(port); -} - -void sh7751se_outl(unsigned int value, unsigned long port) -{ - if (PXSEG(port)) - *(volatile unsigned long *)port = value; - else - maybebadio(port); -} - -void sh7751se_insl(unsigned long port, void *addr, unsigned long count) -{ - maybebadio(port); -} - -void sh7751se_outsl(unsigned long port, const void *addr, unsigned long count) -{ - maybebadio(port); -} diff --git a/arch/sh/boards/mach-se/7751/setup.c b/arch/sh/boards/mach-se/7751/setup.c index 5057251..9fbc51b 100644 --- a/arch/sh/boards/mach-se/7751/setup.c +++ b/arch/sh/boards/mach-se/7751/setup.c @@ -56,23 +56,5 @@ __initcall(se7751_devices_setup); static struct sh_machine_vector mv_7751se __initmv = { .mv_name = "7751 SolutionEngine", .mv_nr_irqs = 72, - - .mv_inb = sh7751se_inb, - .mv_inw = sh7751se_inw, - .mv_inl = sh7751se_inl, - .mv_outb = sh7751se_outb, - .mv_outw = sh7751se_outw, - .mv_outl = sh7751se_outl, - - .mv_inb_p = sh7751se_inb_p, - .mv_inw_p = sh7751se_inw, - .mv_inl_p = sh7751se_inl, - .mv_outb_p = sh7751se_outb_p, - .mv_outw_p = sh7751se_outw, - .mv_outl_p = sh7751se_outl, - - .mv_insl = sh7751se_insl, - .mv_outsl = sh7751se_outsl, - .mv_init_irq = init_7751se_IRQ, }; -- cgit v1.1 From 5aefa34fada9d17a00635516688de34702451708 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Mon, 1 Nov 2010 15:30:31 -0400 Subject: sh: clkfwk: Fix up rate rounding error handling. According to the linux/clk.h definition we should be handing back an errno value or a valid rate. This fixes up the case where 0 can be returned for invalid frequencies or cases where rounding has no selectable candidate. Reported-by: Guennadi Liakhovetski Signed-off-by: Paul Mundt --- drivers/sh/clk/core.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/sh/clk/core.c b/drivers/sh/clk/core.c index fd0d1b9..8611443 100644 --- a/drivers/sh/clk/core.c +++ b/drivers/sh/clk/core.c @@ -90,8 +90,8 @@ struct clk_rate_round_data { static long clk_rate_round_helper(struct clk_rate_round_data *rounder) { unsigned long rate_error, rate_error_prev = ~0UL; - unsigned long rate_best_fit = rounder->rate; unsigned long highest, lowest, freq; + long rate_best_fit = -ENOENT; int i; highest = 0; @@ -146,7 +146,7 @@ long clk_rate_table_round(struct clk *clk, }; if (clk->nr_freqs < 1) - return 0; + return -ENOSYS; return clk_rate_round_helper(&table_round); } -- cgit v1.1 From 20f95e0b22ea45c1798261064baab57efeb3b3bc Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Mon, 1 Nov 2010 16:10:48 -0400 Subject: sh: intc: Update for single IRQ reservation helper. Signed-off-by: Paul Mundt --- drivers/sh/intc/core.c | 2 +- drivers/sh/intc/dynamic.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/sh/intc/core.c b/drivers/sh/intc/core.c index 873a99f..e5e9e67 100644 --- a/drivers/sh/intc/core.c +++ b/drivers/sh/intc/core.c @@ -79,7 +79,7 @@ static void __init intc_register_irq(struct intc_desc *desc, * Register the IRQ position with the global IRQ map, then insert * it in to the radix tree. */ - irq_reserve_irqs(irq, 1); + irq_reserve_irq(irq); raw_spin_lock_irqsave(&intc_big_lock, flags); radix_tree_insert(&d->tree, enum_id, intc_irq_xlate_get(irq)); diff --git a/drivers/sh/intc/dynamic.c b/drivers/sh/intc/dynamic.c index 4187cce..a3677c9 100644 --- a/drivers/sh/intc/dynamic.c +++ b/drivers/sh/intc/dynamic.c @@ -60,5 +60,5 @@ void reserve_intc_vectors(struct intc_vect *vectors, unsigned int nr_vecs) int i; for (i = 0; i < nr_vecs; i++) - irq_reserve_irqs(evt2irq(vectors[i].vect), 1); + irq_reserve_irq(evt2irq(vectors[i].vect)); } -- cgit v1.1 From e96ce8ebfd7427c7ce335028f6619fb549f366b2 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Thu, 4 Nov 2010 12:29:00 +0900 Subject: sh: mach-se: Fix up SE7206 no ioport build. There was a leftover inw() used here that really just wants to be a __raw_readw() instead. Convert it over. Signed-off-by: Paul Mundt --- arch/sh/boards/mach-se/7206/irq.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/arch/sh/boards/mach-se/7206/irq.c b/arch/sh/boards/mach-se/7206/irq.c index 883b21e..d96194960 100644 --- a/arch/sh/boards/mach-se/7206/irq.c +++ b/arch/sh/boards/mach-se/7206/irq.c @@ -139,11 +139,13 @@ void __init init_se7206_IRQ(void) make_se7206_irq(IRQ0_IRQ); /* SMC91C111 */ make_se7206_irq(IRQ1_IRQ); /* ATA */ make_se7206_irq(IRQ3_IRQ); /* SLOT / PCM */ - __raw_writew(inw(INTC_ICR1) | 0x000b ,INTC_ICR1 ) ; /* ICR1 */ + + __raw_writew(__raw_readw(INTC_ICR1) | 0x000b, INTC_ICR); /* ICR1 */ /* FPGA System register setup*/ __raw_writew(0x0000,INTSTS0); /* Clear INTSTS0 */ __raw_writew(0x0000,INTSTS1); /* Clear INTSTS1 */ + /* IRQ0=LAN, IRQ1=ATA, IRQ3=SLT,PCM */ __raw_writew(0x0001,INTSEL); } -- cgit v1.1 From e2fcf74f3d3dabe8591732cd37869a0cc88ed7a5 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Thu, 4 Nov 2010 12:32:24 +0900 Subject: sh: nommu: use 32-bit phys mode. The nommu code has regressed somewhat in that 29BIT gets set for the SH-2/2A configs regardless of the fact that they are really 32BIT sans MMU or PMB. This does a bit of tidying to get nommu properly selecting 32BIT as it was before. Signed-off-by: Paul Mundt --- arch/sh/Kconfig | 1 + arch/sh/include/asm/addrspace.h | 8 ++++---- arch/sh/mm/Kconfig | 2 +- arch/sh/mm/consistent.c | 15 +++++++-------- arch/sh/mm/uncached.c | 2 +- 5 files changed, 14 insertions(+), 14 deletions(-) diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig index 5c075f5..7f217b3 100644 --- a/arch/sh/Kconfig +++ b/arch/sh/Kconfig @@ -193,6 +193,7 @@ config CPU_SH2 config CPU_SH2A bool select CPU_SH2 + select UNCACHED_MAPPING config CPU_SH3 bool diff --git a/arch/sh/include/asm/addrspace.h b/arch/sh/include/asm/addrspace.h index 446b383..3d1ae2b 100644 --- a/arch/sh/include/asm/addrspace.h +++ b/arch/sh/include/asm/addrspace.h @@ -44,10 +44,10 @@ /* * These will never work in 32-bit, don't even bother. */ -#define P1SEGADDR(a) __futile_remapping_attempt -#define P2SEGADDR(a) __futile_remapping_attempt -#define P3SEGADDR(a) __futile_remapping_attempt -#define P4SEGADDR(a) __futile_remapping_attempt +#define P1SEGADDR(a) ({ (void)(a); BUG(); NULL; }) +#define P2SEGADDR(a) ({ (void)(a); BUG(); NULL; }) +#define P3SEGADDR(a) ({ (void)(a); BUG(); NULL; }) +#define P4SEGADDR(a) ({ (void)(a); BUG(); NULL; }) #endif #endif /* P1SEG */ diff --git a/arch/sh/mm/Kconfig b/arch/sh/mm/Kconfig index 0937039..c3e61b3 100644 --- a/arch/sh/mm/Kconfig +++ b/arch/sh/mm/Kconfig @@ -79,7 +79,7 @@ config 29BIT config 32BIT bool - default y if CPU_SH5 + default y if CPU_SH5 || !MMU config PMB bool "Support 32-bit physical addressing through PMB" diff --git a/arch/sh/mm/consistent.c b/arch/sh/mm/consistent.c index 0387932..40733a9 100644 --- a/arch/sh/mm/consistent.c +++ b/arch/sh/mm/consistent.c @@ -79,21 +79,20 @@ void dma_generic_free_coherent(struct device *dev, size_t size, void dma_cache_sync(struct device *dev, void *vaddr, size_t size, enum dma_data_direction direction) { -#if defined(CONFIG_CPU_SH5) || defined(CONFIG_PMB) - void *p1addr = vaddr; -#else - void *p1addr = (void*) P1SEGADDR((unsigned long)vaddr); -#endif + void *addr; + + addr = __in_29bit_mode() ? + (void *)P1SEGADDR((unsigned long)vaddr) : vaddr; switch (direction) { case DMA_FROM_DEVICE: /* invalidate only */ - __flush_invalidate_region(p1addr, size); + __flush_invalidate_region(addr, size); break; case DMA_TO_DEVICE: /* writeback only */ - __flush_wback_region(p1addr, size); + __flush_wback_region(addr, size); break; case DMA_BIDIRECTIONAL: /* writeback and invalidate */ - __flush_purge_region(p1addr, size); + __flush_purge_region(addr, size); break; default: BUG(); diff --git a/arch/sh/mm/uncached.c b/arch/sh/mm/uncached.c index 8a4eca5..a7767da 100644 --- a/arch/sh/mm/uncached.c +++ b/arch/sh/mm/uncached.c @@ -28,7 +28,7 @@ EXPORT_SYMBOL(virt_addr_uncached); void __init uncached_init(void) { -#ifdef CONFIG_29BIT +#if defined(CONFIG_29BIT) || !defined(CONFIG_MMU) uncached_start = P2SEG; #else uncached_start = memory_end; -- cgit v1.1 From edc9a958fd31ef1d89f9eaee82b2a3882c8e34c9 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Thu, 4 Nov 2010 12:46:19 +0900 Subject: sh: nommu: Support building without an uncached mapping. Now that nommu selects 32BIT we run in to the situation where SH-2A supports an uncached identity mapping by way of the BSC, while the SH-2 does not. This provides stubs for the PC manglers and tidies up some of the system*.h mess in the process. Signed-off-by: Paul Mundt --- arch/sh/include/asm/system.h | 4 +--- arch/sh/include/asm/system_32.h | 36 ------------------------------------ arch/sh/include/asm/system_64.h | 3 --- arch/sh/include/asm/uncached.h | 40 ++++++++++++++++++++++++++++++++++++++++ 4 files changed, 41 insertions(+), 42 deletions(-) diff --git a/arch/sh/include/asm/system.h b/arch/sh/include/asm/system.h index 1f1af5a..10c8b18 100644 --- a/arch/sh/include/asm/system.h +++ b/arch/sh/include/asm/system.h @@ -10,6 +10,7 @@ #include #include #include +#include #define AT_VECTOR_SIZE_ARCH 5 /* entries in ARCH_DLINFO */ @@ -137,9 +138,6 @@ extern unsigned int instruction_size(unsigned int insn); #define instruction_size(insn) (4) #endif -extern unsigned long cached_to_uncached; -extern unsigned long uncached_size; - void per_cpu_trap_init(void); void default_idle(void); void cpu_idle_wait(void); diff --git a/arch/sh/include/asm/system_32.h b/arch/sh/include/asm/system_32.h index c941b27..a4ad1cd 100644 --- a/arch/sh/include/asm/system_32.h +++ b/arch/sh/include/asm/system_32.h @@ -145,42 +145,6 @@ do { \ __restore_dsp(prev); \ } while (0) -/* - * Jump to uncached area. - * When handling TLB or caches, we need to do it from an uncached area. - */ -#define jump_to_uncached() \ -do { \ - unsigned long __dummy; \ - \ - __asm__ __volatile__( \ - "mova 1f, %0\n\t" \ - "add %1, %0\n\t" \ - "jmp @%0\n\t" \ - " nop\n\t" \ - ".balign 4\n" \ - "1:" \ - : "=&z" (__dummy) \ - : "r" (cached_to_uncached)); \ -} while (0) - -/* - * Back to cached area. - */ -#define back_to_cached() \ -do { \ - unsigned long __dummy; \ - ctrl_barrier(); \ - __asm__ __volatile__( \ - "mov.l 1f, %0\n\t" \ - "jmp @%0\n\t" \ - " nop\n\t" \ - ".balign 4\n" \ - "1: .long 2f\n" \ - "2:" \ - : "=&r" (__dummy)); \ -} while (0) - #ifdef CONFIG_CPU_HAS_SR_RB #define lookup_exception_vector() \ ({ \ diff --git a/arch/sh/include/asm/system_64.h b/arch/sh/include/asm/system_64.h index 3633864..8593bc8d 100644 --- a/arch/sh/include/asm/system_64.h +++ b/arch/sh/include/asm/system_64.h @@ -34,9 +34,6 @@ do { \ &next->thread); \ } while (0) -#define jump_to_uncached() do { } while (0) -#define back_to_cached() do { } while (0) - #define __icbi(addr) __asm__ __volatile__ ( "icbi %0, 0\n\t" : : "r" (addr)) #define __ocbp(addr) __asm__ __volatile__ ( "ocbp %0, 0\n\t" : : "r" (addr)) #define __ocbi(addr) __asm__ __volatile__ ( "ocbi %0, 0\n\t" : : "r" (addr)) diff --git a/arch/sh/include/asm/uncached.h b/arch/sh/include/asm/uncached.h index e3419f9..6f8816b 100644 --- a/arch/sh/include/asm/uncached.h +++ b/arch/sh/include/asm/uncached.h @@ -4,15 +4,55 @@ #include #ifdef CONFIG_UNCACHED_MAPPING +extern unsigned long cached_to_uncached; +extern unsigned long uncached_size; extern unsigned long uncached_start, uncached_end; extern int virt_addr_uncached(unsigned long kaddr); extern void uncached_init(void); extern void uncached_resize(unsigned long size); + +/* + * Jump to uncached area. + * When handling TLB or caches, we need to do it from an uncached area. + */ +#define jump_to_uncached() \ +do { \ + unsigned long __dummy; \ + \ + __asm__ __volatile__( \ + "mova 1f, %0\n\t" \ + "add %1, %0\n\t" \ + "jmp @%0\n\t" \ + " nop\n\t" \ + ".balign 4\n" \ + "1:" \ + : "=&z" (__dummy) \ + : "r" (cached_to_uncached)); \ +} while (0) + +/* + * Back to cached area. + */ +#define back_to_cached() \ +do { \ + unsigned long __dummy; \ + ctrl_barrier(); \ + __asm__ __volatile__( \ + "mov.l 1f, %0\n\t" \ + "jmp @%0\n\t" \ + " nop\n\t" \ + ".balign 4\n" \ + "1: .long 2f\n" \ + "2:" \ + : "=&r" (__dummy)); \ +} while (0) #else #define virt_addr_uncached(kaddr) (0) #define uncached_init() do { } while (0) #define uncached_resize(size) BUG() +#define jump_to_uncached() do { } while (0) +#define back_to_cached() do { } while (0) #endif #endif /* __ASM_SH_UNCACHED_H */ -- cgit v1.1 From ccedb20c6879ac0237b95b3500d69822f1e5e2ea Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Thu, 4 Nov 2010 12:51:08 +0900 Subject: sh: Simplify phys_addr_mask()/PTE_PHYS_MASK for 29/32-bit. Given that __in_29bit_mode() is a constant for the non-PMB case, we can simply use the PMB-facing version of phys_addr_mask() and drop the other variants. Signed-off-by: Paul Mundt --- arch/sh/include/asm/pgtable.h | 12 ------------ 1 file changed, 12 deletions(-) diff --git a/arch/sh/include/asm/pgtable.h b/arch/sh/include/asm/pgtable.h index a15f105..083ea06 100644 --- a/arch/sh/include/asm/pgtable.h +++ b/arch/sh/include/asm/pgtable.h @@ -66,7 +66,6 @@ static inline unsigned long long neff_sign_extend(unsigned long val) #define PHYS_ADDR_MASK29 0x1fffffff #define PHYS_ADDR_MASK32 0xffffffff -#ifdef CONFIG_PMB static inline unsigned long phys_addr_mask(void) { /* Is the MMU in 29bit mode? */ @@ -75,17 +74,6 @@ static inline unsigned long phys_addr_mask(void) return PHYS_ADDR_MASK32; } -#elif defined(CONFIG_32BIT) -static inline unsigned long phys_addr_mask(void) -{ - return PHYS_ADDR_MASK32; -} -#else -static inline unsigned long phys_addr_mask(void) -{ - return PHYS_ADDR_MASK29; -} -#endif #define PTE_PHYS_MASK (phys_addr_mask() & PAGE_MASK) #define PTE_FLAGS_MASK (~(PTE_PHYS_MASK) << PAGE_SHIFT) -- cgit v1.1 From 6af26c6c99f01e810f9944543df810e320284aa3 Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Tue, 2 Nov 2010 11:27:24 +0000 Subject: sh: add clk_round_parent() to optimize parent clock rate Sometimes it is possible and reasonable to adjust the parent clock rate to improve precision of the child clock, e.g., if the child clock has no siblings. clk_round_parent() is a new addition to the SH clock-framework API, that implements such an optimization for child clocks with divisors, taking all integer values in a range. Signed-off-by: Guennadi Liakhovetski Signed-off-by: Paul Mundt --- drivers/sh/clk/core.c | 75 ++++++++++++++++++++++++++++++++++++++++++++++++++ include/linux/sh_clk.h | 4 +++ 2 files changed, 79 insertions(+) diff --git a/drivers/sh/clk/core.c b/drivers/sh/clk/core.c index 8611443..b384059 100644 --- a/drivers/sh/clk/core.c +++ b/drivers/sh/clk/core.c @@ -541,6 +541,81 @@ long clk_round_rate(struct clk *clk, unsigned long rate) } EXPORT_SYMBOL_GPL(clk_round_rate); +long clk_round_parent(struct clk *clk, unsigned long target, + unsigned long *best_freq, unsigned long *parent_freq, + unsigned int div_min, unsigned int div_max) +{ + struct cpufreq_frequency_table *freq, *best = NULL; + unsigned long error = ULONG_MAX, freq_high, freq_low, div; + struct clk *parent = clk_get_parent(clk); + + if (!parent) { + *parent_freq = 0; + *best_freq = clk_round_rate(clk, target); + return abs(target - *best_freq); + } + + for (freq = parent->freq_table; freq->frequency != CPUFREQ_TABLE_END; + freq++) { + if (freq->frequency == CPUFREQ_ENTRY_INVALID) + continue; + + if (unlikely(freq->frequency / target <= div_min - 1)) { + unsigned long freq_max = (freq->frequency + div_min / 2) / div_min; + if (error > target - freq_max) { + error = target - freq_max; + best = freq; + if (best_freq) + *best_freq = freq_max; + } + pr_debug("too low freq %lu, error %lu\n", freq->frequency, target - freq_max); + if (!error) + break; + continue; + } + + if (unlikely(freq->frequency / target >= div_max)) { + unsigned long freq_min = (freq->frequency + div_max / 2) / div_max; + if (error > freq_min - target) { + error = freq_min - target; + best = freq; + if (best_freq) + *best_freq = freq_min; + } + pr_debug("too high freq %lu, error %lu\n", freq->frequency, freq_min - target); + if (!error) + break; + continue; + } + + + div = freq->frequency / target; + freq_high = freq->frequency / div; + freq_low = freq->frequency / (div + 1); + if (freq_high - target < error) { + error = freq_high - target; + best = freq; + if (best_freq) + *best_freq = freq_high; + } + if (target - freq_low < error) { + error = target - freq_low; + best = freq; + if (best_freq) + *best_freq = freq_low; + } + pr_debug("%u / %lu = %lu, / %lu = %lu, best %lu, parent %u\n", + freq->frequency, div, freq_high, div + 1, freq_low, + *best_freq, best->frequency); + if (!error) + break; + } + if (parent_freq) + *parent_freq = best->frequency; + return error; +} +EXPORT_SYMBOL_GPL(clk_round_parent); + #ifdef CONFIG_PM static int clks_sysdev_suspend(struct sys_device *dev, pm_message_t state) { diff --git a/include/linux/sh_clk.h b/include/linux/sh_clk.h index 4dca992..cea0c38 100644 --- a/include/linux/sh_clk.h +++ b/include/linux/sh_clk.h @@ -122,6 +122,10 @@ int clk_rate_table_find(struct clk *clk, long clk_rate_div_range_round(struct clk *clk, unsigned int div_min, unsigned int div_max, unsigned long rate); +long clk_round_parent(struct clk *clk, unsigned long target, + unsigned long *best_freq, unsigned long *parent_freq, + unsigned int div_min, unsigned int div_max); + #define SH_CLK_MSTP32(_parent, _enable_reg, _enable_bit, _flags) \ { \ .parent = _parent, \ -- cgit v1.1 From d0013c9e3bc75b3e1652bd5999a9a8d56a822ce4 Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Thu, 4 Nov 2010 14:14:29 +0000 Subject: sh: make some needlessly global sh7724 clocks static These clocks are currently only used inside one .c file and are not declared in any headers, therefore having them global is useless. Signed-off-by: Guennadi Liakhovetski Signed-off-by: Paul Mundt --- arch/sh/kernel/cpu/sh4a/clock-sh7724.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/sh/kernel/cpu/sh4a/clock-sh7724.c b/arch/sh/kernel/cpu/sh4a/clock-sh7724.c index 2d9700c..0fe2e93 100644 --- a/arch/sh/kernel/cpu/sh4a/clock-sh7724.c +++ b/arch/sh/kernel/cpu/sh4a/clock-sh7724.c @@ -48,7 +48,7 @@ static struct clk r_clk = { * Default rate for the root input clock, reset this with clk_set_rate() * from the platform code. */ -struct clk extal_clk = { +static struct clk extal_clk = { .rate = 33333333, }; @@ -111,7 +111,7 @@ static struct clk div3_clk = { .parent = &pll_clk, }; -struct clk *main_clks[] = { +static struct clk *main_clks[] = { &r_clk, &extal_clk, &fll_clk, @@ -156,7 +156,7 @@ struct clk div4_clks[DIV4_NR] = { enum { DIV6_V, DIV6_FA, DIV6_FB, DIV6_I, DIV6_S, DIV6_NR }; -struct clk div6_clks[DIV6_NR] = { +static struct clk div6_clks[DIV6_NR] = { [DIV6_V] = SH_CLK_DIV6(&div3_clk, VCLKCR, 0), [DIV6_FA] = SH_CLK_DIV6(&div3_clk, FCLKACR, 0), [DIV6_FB] = SH_CLK_DIV6(&div3_clk, FCLKBCR, 0), -- cgit v1.1 From a766b29790b2b6582345624a6e9e686d8015efe1 Mon Sep 17 00:00:00 2001 From: Paul Mundt Date: Mon, 8 Nov 2010 09:40:23 +0900 Subject: sh: clkfwk: Fix up checkpatch warnings. The clk_round_parent() change introduced various checkpatch warnings, tidy them up. Signed-off-by: Paul Mundt --- drivers/sh/clk/core.c | 27 ++++++++++++++++++++++----- 1 file changed, 22 insertions(+), 5 deletions(-) diff --git a/drivers/sh/clk/core.c b/drivers/sh/clk/core.c index b384059..09615b5 100644 --- a/drivers/sh/clk/core.c +++ b/drivers/sh/clk/core.c @@ -561,57 +561,74 @@ long clk_round_parent(struct clk *clk, unsigned long target, continue; if (unlikely(freq->frequency / target <= div_min - 1)) { - unsigned long freq_max = (freq->frequency + div_min / 2) / div_min; + unsigned long freq_max; + + freq_max = (freq->frequency + div_min / 2) / div_min; if (error > target - freq_max) { error = target - freq_max; best = freq; if (best_freq) *best_freq = freq_max; } - pr_debug("too low freq %lu, error %lu\n", freq->frequency, target - freq_max); + + pr_debug("too low freq %lu, error %lu\n", freq->frequency, + target - freq_max); + if (!error) break; + continue; } if (unlikely(freq->frequency / target >= div_max)) { - unsigned long freq_min = (freq->frequency + div_max / 2) / div_max; + unsigned long freq_min; + + freq_min = (freq->frequency + div_max / 2) / div_max; if (error > freq_min - target) { error = freq_min - target; best = freq; if (best_freq) *best_freq = freq_min; } - pr_debug("too high freq %lu, error %lu\n", freq->frequency, freq_min - target); + + pr_debug("too high freq %lu, error %lu\n", freq->frequency, + freq_min - target); + if (!error) break; + continue; } - div = freq->frequency / target; freq_high = freq->frequency / div; freq_low = freq->frequency / (div + 1); + if (freq_high - target < error) { error = freq_high - target; best = freq; if (best_freq) *best_freq = freq_high; } + if (target - freq_low < error) { error = target - freq_low; best = freq; if (best_freq) *best_freq = freq_low; } + pr_debug("%u / %lu = %lu, / %lu = %lu, best %lu, parent %u\n", freq->frequency, div, freq_high, div + 1, freq_low, *best_freq, best->frequency); + if (!error) break; } + if (parent_freq) *parent_freq = best->frequency; + return error; } EXPORT_SYMBOL_GPL(clk_round_parent); -- cgit v1.1