summaryrefslogtreecommitdiffstats
path: root/sound/soc/codecs/sgtl5000.c
Commit message (Collapse)AuthorAgeFilesLines
...
| * ASoC: sgtl5000: Fix voltage units in dev_err messageFabio Estevam2011-12-281-1/+1
| | | | | | | | | | | | | | | | vdda, vddio and vddd are voltages expressed in milivolts (mV), so use the proper annotation. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
| * ASoC: Drop unused state parameter from CODEC suspend callbackLars-Peter Clausen2011-12-021-1/+1
| | | | | | | | | | | | | | | | | | | | The existence of this parameter is purely historical. None of the CODEC drivers uses it and we always pass in the same value anyway, so it should be safe to remove it. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
| * ASoC: Remove unneeded platform_device.h inclusions from CODECsMark Brown2011-11-271-1/+0
| | | | | | | | | | | | They've not been needed for a long time if they were ever required. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
| * ASoC: Constify snd_soc_dai_ops structsLars-Peter Clausen2011-11-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure") introduced the possibility to have constant DAI ops structures, yet this is barley used in both existing drivers and also new drivers being submitted, although none of them modifies its DAI ops structure. The later is not surprising since existing drivers are often used as templates for new drivers. So this patch just constifies all existing snd_soc_dai_ops structs to eliminate the issue altogether. The patch was generated with the following coccinelle semantic patch: // <smpl> @@ identifier ops; @@ -struct snd_soc_dai_ops ops = +const struct snd_soc_dai_ops ops = { ... }; // </smpl> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | Merge branch 'for-linus' of ↵Linus Torvalds2012-01-101-1/+1
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (40 commits) regulator: set constraints.apply_uV to 0 in of_get_fixed_voltage_config regulator: max8925: fix enabled/disabled judgement mistake regulator: add regulator_bulk_force_disable function regulator: pass regulator_register of_node in fixed voltage driver regulator: add regulator_force_disable() definition for !CONFIG_REGULATOR regulator: Enable supply regulator if child rail is enabled. regulator: mc13892: Convert to devm_kzalloc() regulator: mc13783: Convert to devm_kzalloc() regulator: Fix checking return value of create_regulator regulator: Fix the error handling if create_regulator fails regulator: Export regulator_is_supported_voltage() regulator: mc13892: add device tree probe support regulator: mc13892: remove the unnecessary prefix from regulator name regulator: Convert wm831x regulator drivers to devm_kzalloc() regulator: da9052: Staticize non-exported symbols regulator: Replace kzalloc with devm_kzalloc and if-else with a switch-case for da9052-regulator regulator: Update da9052-regulator for DT changes regulator: DA9052/53 Regulator support regulator: pass device_node to of_get_regulator_init_data() regulator: If a single voltage is set with device tree then set apply_uV ...
| * regulator: pass additional of_node to regulator_register()Rajendra Nayak2011-11-231-1/+1
| | | | | | | | | | | | | | | | | | | | | | With device tree support for regulators, its needed that the regulator_dev->dev device has the right of_node attached. To be able to do this add an additional parameter to the regulator_register() api, wherein the dt-adapted driver can then pass this additional info onto the regulator core. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: sgtl5000: fix DB_RANGE sizeClemens Ladisch2011-11-201-1/+1
|/ | | | | | | Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent reading more data than actually is in the array. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
* ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits callsAxel Lin2011-10-221-6/+6
| | | | | | | | | Ensure all mask bits are clear before setting new value. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Dong Aisheng <b29396@freescale.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask valueAxel Lin2011-10-211-3/+3
| | | | | | | | | | We have defined SGTL5000_LINREG_VDDD_MASK in sgtl5000.h, use it instead of hardcoded (0x1 << 4) - 1 for the mask. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Set sgtl5000->ldo in ldo_regulator_registerAxel Lin2011-10-211-0/+2
| | | | | | | | | | Otherwise calling ldo_regulator_remove() does not unregister regulator and free memories. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: sgtl5000: Fix setting mic bias resistorAxel Lin2011-10-191-6/+3
| | | | | | | | | | | | | | | | | | | According to the datasheet: CHIP_MIC_CTRL 0x002A BITS[9:8] BIAS_RESISTOR 0x0 = Powerd off 0x1 = 2.0 kohm 0x2 = 4.0 kohm 0x3 = 8.0 kohm To set mic bias resistor, we need to update bits[9:8] of SGTL5000_CHIP_MIC_CTRL register. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: sgtl5000: fix module device table type for sgtl5000_dt_idsAxel Lin2011-08-121-1/+1
| | | | | | | | The module device table for of_device_id should use "of" type. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* Merge branch 'for-3.1' into for-3.2Mark Brown2011-08-081-94/+35
|\ | | | | | | | | | | | | | | Conflict due to the fix for the register map failure - taken the for-3.1 version. Conflicts: sound/soc/codecs/sgtl5000.c
| * ASoC: sgtl5000: fix cache handlingWolfram Sang2011-08-031-93/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cache handling in this driver is broken. The chip has 16-bit registers, yet the register numbers also increase by 2 per register, i.e. there are only even-numbered registers. The cache in this driver, though, simply increments register numbers, so it does need some mapping as seen in sgtl5000_restore_regs(), note the '>> 1': snd_soc_write(codec, SGTL5000_CHIP_LINREG_CTRL, cache[SGTL5000_CHIP_LINREG_CTRL >> 1]); That, of course, won't work with snd_soc_update_bits(). (Thus, we won't even notice the missing register 0x1c in the default regs which shifted all follwing registers to wrong values.) Noticed on the MX28EVK where enabling the regulators simply locked up the chip. Refactor the routines and use a properly sized default_regs array which matches the register layout of the underlying chip, i.e. create a truly flat cache. This also saves some code which should make up for the bigger array a little. When soc-core will somewhen have another cache type which handles a step size, this conversion will also ease the transition. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Tested-by: Dong Aisheng <b29396@freescale.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
* | ASoC: sgtl5000: add one missed cache regDong Aisheng2011-08-011-0/+1
| | | | | | | | | | | | | | | | Signed-off-by: Dong Aisheng <b29396@freescale.com> Signed-off-by: Zeng Zhaoming <zhaoming.zeng@freescale.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* | ASoC: sgtl5000: add device tree probe supportShawn Guo2011-07-291-0/+8
|/ | | | | | | | | It adds device tree probe support for sgtl5000 driver. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: sgtl5000: guide user when regulator support is neededWolfram Sang2011-07-191-0/+1
| | | | | | | | | | | Print a hint when the user has a setup where CONFIG_REGULATOR is really needed to make the driver work. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Tested-by: Dong Aisheng <b29396@freescale.com> Tested-by: Shawn Guo <shawn.guo@freescale.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: sgtl5000: refactor registering internal ldoWolfram Sang2011-07-191-38/+31
| | | | | | | | | | | The code for registering the internal ldo was present twice. Turn it into a function instead. Also, inform the user if LDO is used now. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Tested-by: Dong Aisheng <b29396@freescale.com> Tested-by: Shawn Guo <shawn.guo@freescale.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Support !REGULATOR build for sgtl5000Mark Brown2011-03-221-0/+14
| | | | | | | The regulator is optional depending on board design. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* ASoC: sgtl5000: use after free in ldo_regulator_register()Dan Carpenter2011-03-081-1/+3
| | | | | | | | The "ldo" variable was dereferenced after free on the error path. Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Staticise non-exported symbols in SGTL5000Mark Brown2011-02-281-3/+3
| | | | Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: remove unnecessary header including in SGTL5000 codec driverZeng Zhaoming2011-02-281-1/+0
| | | | | | | | | Remove unnecessary headers: - mach/hardware.h in sgtl5000.c - linux/i2c.h in sgtl5000.h Signed-off-by: Zeng Zhaoming <b32542@freescale.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Add Freescale SGTL5000 codec supportZeng Zhaoming2011-02-251-0/+1512
Add Freescale SGTL5000 codec support. Supported features: - line-in and mic input - headphone and line-out output - line-in bypass ADC and DAC to headphone - 16, 20, 24, 32 bit audio - 8 ~ 96k sample rates Signed-off-by: Zeng Zhaoming <zhaoming.zeng@freescale.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
OpenPOWER on IntegriCloud