| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
| |
AC_VERB_GET_DIGI_CONVERT_2 isn't actually implemented but reserved.
The whole SIC bits are returned from DIGI_CONVERT_1.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
|
|
|
|
|
| |
Keep the format verb at closing PCM streams.
Introduced snd_hda_codec_cleanup_stream() for the parcicular purpose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In the current scheme, PCM device numbers are assigned incrementally
in the order of codecs. This causes problems when the codec number
is irregular, e.g. codec #0 for HDMI and codec #1 for analog. Then
the HDMI becomes the first PCM, which is picked up as the default
output device. Unfortuantely this doesn't work well with normal
setups.
This patch introduced the fixed device numbers for the PCM types,
namely, analog, SPDIF, HDMI and modem. The PCM devices are assigned
according to the corresponding PCM type. After this patch, HDMI will
be always assigned to PCM #3, SPDIF to PCM #1, and the first analog
to PCM #0, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
| |
Added afg and mfg preset masks for more finer codec-preset selection.
Signed-off-by: Marc Boucher <marc@linuxant.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds additional output to the /proc codec#X info.
The following pieces of information are added to the output:
- Balanced, L/R swap, trigger, impedance sense pin capabilities
- Vref pin capabilities
- Current Vref pin widget control setting
- Default configuration association, sequence, and misc bit test
- EAPD/BTL bits conveying balanced mode, EAPD, and L/R swap
- Power state modified to show state name as well as setting vs actual value
- GPIO parameter output on Audio Function Group, including enumeration of IO
pins which are indicated present (Any I and O pins are not output at this
time)
- Stripe and L/R swap widget capabilities
- All digital converter bits: enable, validity, validity config, preemphasis,
copyright, non-audio, professional, generation level, and content category
- Converter stream and channel values for in/out widgets
- SDI select value for in widgets
- Unsolicited response widget capability tag and enabled bit
- Delay widget capability value
- Processing widget capability benign bit and number of coefficients
- Realtek Define Registers: processing coefficient, coefficient index
[Also, fixed space/tab issues and make codes a bit more readable
-- Takashi]
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
|
|
|
|
|
|
|
|
|
| |
Some machines with STAC codecs seem to have problems (e.g. no audible
playback) when the delay in codec-read routine is too short.
I still don't figure out which command sequence causes this problem
(due to lack of test hardware), but it's known that increasing the
delay fixes. So, added a stupid workaround here temporarily...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Added AC_VERB_GET_DIGI_CONVERT_2 and renamed AC_VERB_GET_DIGI_CONVERT to
AC_VERB_GET_DIGI_CONVERT_1 to stay consistent with the SET variants. Added
AC_VERB_GET_GPIO_UNSOLICITED_RSP_MASK, AC_VERB_SET_GPIO_UNSOLICITED_RSP_MASK,
and AC_PINCAP_LR_SWAP. The missing fields were listed in the ALC883 datasheet
rev 1.3.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
|
|
|
|
| |
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
|
|
|
|
|
|
|
| |
AC_KNBCAP_DELTA is incorrectly defined as (1<<8). According to the Intel
HDA spec, this is bit 7 after AC_KNBCAP_NUM_STEPS which is a 0x7f mask.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
|
|
|
|
|
|
| |
Show more attributs of volume-knob widgets.
Also don't put empty lines when no connection list is found.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Comment in hda_intel.c states that 'the explicit resume is needed only
when POWER_SAVE isn't set', but this is not true.
There is no code that will automaticly power up the codec on resume,
but only code that powers it up when user accesses it. So if user
leaves a sound playing, codec will not be powered
To fix that I check if there are any codecs that should be powered
codec->power_count, and if so I power them up together with main
controller.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
|
|
|
| |
Avoid unnecessary work scheduling for power-off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Added CONFIG_SND_HDA_POWER_SAVE kconfig. It's an experimental option
to achieve an aggressive power-saving. With this option, the driver
will turn on/off the power of each codec and controller chip dynamically
on demand.
The patch introduces a new module option 'power_save'. It specifies
the second of time-out for automatic power-down. As default, it's
10 seconds. Setting 0 means to suppress the power-saving feature.
The codec may have analog-input loopbacks, which are usually represented
by mixer elements such as 'Mic Playback Switch' or 'CD Playback Switch'.
When these are on, we cannot turn off the mixer and the codec chip has
to be kept on. For bookkeeping these states, a new codec-callback is
introduced.
For the bus-controller side, a new callback pm_notify is introduced,
which can be used to turn on/off the contoller appropriately.
Note that this power-saving might cause slight click-noise at
power-on/off. Also, it might take some time to wake up the codec, and
might even drop some tones at the very beginning. This seems to be the
side-effect of turning off the controller chip.
This turn-off of the controller can be disabled by undefining
HDA_POWER_SAVE_RESET_CONTOLLER in hda_intel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
So far, the driver looked the table of snd_kcontrol_new used for creating
mixer elements and forces to call each of its put callbacks in PM resume
code. This is too ugly and hackish.
Now, the resume is simplified using the codec amp and command register
caches. The driver simply restores the values that have been written
in the cache table. With this simplification, most codec support codes
don't require any special resume callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the cache for codec command registers.
snd_hda_codec_write_cache() and snd_hda_sequence_write_cache() do
the write operations with caching, which values can be resumed via
snd_hda_codec_resume_cache().
The patch introduces only the framework, and no codec code is using
this cache yet. It'll be implemented in the following patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
|
|
|
|
|
| |
Rewrite the code to handle amp cache and hash tables to be more
generic. This routine will be used by the register caches in the
next patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
|
|
|
|
|
| |
Added a hwdep interface for each codec (enabled per kconfig).
This interface can be used for reading/writing HD-audio verbs
and other purposes as future extensions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
|
|
|
| |
Fix codes to follow more to the standard kernel coding style.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
|
|
|
|
| |
The AMP mute bit is bit 7. No real influence since no one uses this
definition yet, though...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
| |
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
|
|
|
|
|
|
|
|
|
| |
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
|
|
|
| |
Modules: HDA Codec driver,HDA generic driver
- Fix connection list parsing (with ranged flag).
- Increase the max number of connections
- Introduce widget capabilities cache
- Power up/down widgets at init, suspend and resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
| |
Modules: HDA Codec driver,HDA generic driver
Remove xxx_t typedefs from the HD-Audio codec support codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
| |
Modules: HDA Codec driver
Fix a typo in hda_codec.h.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
| |
Modules: HDA Codec driver
Allocate amp hash array dynamically instead of static array.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
| |
Modules: HDA Codec driver
Get subsytem ID from AFG/MFG if not obtained from the root node.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
|
| |
HDA Codec driver,HDA Intel driver,HDA generic driver
Assign audio PCMs first before modem PCMs.
The modem stream is assigned up to device #6, to be consistent over
different models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
|
|
|
| |
HDA Codec driver,HDA generic driver
Summar: hda-codec - MFG support
This adds Modem Functional Group (MFG) support and option for 9600
sample rate.
Signed-off-by: Sasha Khapyorsky <sashak@smlink.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
|
| |
HDA Codec driver
Adds support for detecting hp insertion/removal and enable/disable of
lineouts based on unsolicited events.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
HDA Codec driver,HDA Intel driver
Merged the work of pshou <pshou@realtek.com.tw> for the support of
more models with ALC codecs: ALC880 ASUS, Uniwill, FSC1734, generic 6-stack,
and ALC260 HP. Tests with the real hardwares are appreciated.
The codec patch is cleaned up: The preset configuration of codecs are
stored in the table and copied to the spec instance.
Added/fixed comments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
| |
HDA Codec driver
Fixed the wrong array size of the codec pointer list.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
| |
HDA Codec driver
Fix and cleanup of CM9880 automatic PIN configuration.
snd_hda_codec_setup_stream() doesn't do anything when NID is 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
| |
HDA Codec driver
Misc clean up: move the definitions of constants for pinctl to a single place.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
|
|
|
| |
HDA Codec driver,HDA generic driver
Fix some vref defines so they are valid for the different bits in
the pin cap and pin control registers. Please apply.
Signed-off-by: Matt <matt@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|