| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
With previous patch, rose_get_neigh() routine
investigates the full list of neighbor nodes
until it finds or not an already connected node whether
it is called locally or through a level 3 transit frame.
If no routes are opened through an adjacent connected node
then a classical connect request is attempted.
Then there is no more reason for an extra loop such
as the one removed by this patch.
Signed-off-by: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
FPAC AX25 packet application is using Linux kernel ROSE
routing skills in order to connect or send packets to remote stations
knowing their ROSE address via a network of interconnected nodes.
Each FPAC node has a ROSE routing table that Linux ROSE module is
looking at each time a ROSE frame is relayed by the node or when
a connect request to a neighbor node is received.
A previous patch improved the system time response by looking at
already established routes each time the system was looking for a
route to relay a frame. If a neighbor node routing the destination
address was already connected, then the frame would be sent
through him. If not, a connection request would be issued.
The present patch extends the same routing capability to a connect
request asked by a user locally connected into an FPAC node.
Without this patch, a connect request was not well handled unless it
was directed to an immediate connected neighbor of the local node.
Implemented at a number of ROSE FPAC node stations, the present patch
improved dramatically FPAC ROSE routing time response and efficiency.
Signed-off-by: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| | |
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/qlcnic/qlcnic_init.c
net/ipv4/ip_output.c
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Just use explicit casts, since we really can't change the
types of structures exported to userspace which have been
around for 15 years or so.
Reported-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
| |
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The other calls to kmalloc in the same function use GFP_ATOMIC, and indeed
two locks are held within the body of the function.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ identifier f; @@
*f(...,GFP_ATOMIC,...)
... when != spin_unlock(...)
when != read_unlock(...)
when != write_unlock(...)
when != read_unlock_irq(...)
when != write_unlock_irq(...)
when != read_unlock_irqrestore(...)
when != write_unlock_irqrestore(...)
when != spin_unlock_irq(...)
when != spin_unlock_irqrestore(...)
*f(...,GFP_KERNEL,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Define a new function to return the waitqueue of a "struct sock".
static inline wait_queue_head_t *sk_sleep(struct sock *sk)
{
return sk->sk_sleep;
}
Change all read occurrences of sk_sleep by a call to this function.
Needed for a future RCU conversion. sk_sleep wont be a field directly
available.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
|
|
|
|
|
| |
Simplify seq_file code.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Wrong ax25_cb refcounting in ax25_send_frame() and by its callers can
cause timer oopses (first reported with 2.6.29.6 kernel).
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14905
Reported-by: Bernard Pidoux <bpidoux@free.fr>
Tested-by: Bernard Pidoux <bpidoux@free.fr>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
cat /proc/net/rose displayed a rose sockets abnormal lci value, i.e.
greater than maximum number of VCs per neighbour allowed.
This number prevents further test of lci value during rose operations.
Example (lines shortened) :
[bernard]# cat /proc/net/rose
dest_addr dest_call src_addr src_call dev lci neigh st vs vr va
* * 2080175520 F6BVP-1 rose0 000 00000 0 0 0 0
2080175520 FPAD-0 2080175520 WP-0 rose0 FFE 00001 3 0 0 0
Here are the default parameters :
linux/include/net/rose.h:#define ROSE_DEFAULT_MAXVC 50 /* Maximum number of VCs per neighbour */
linux/net/rose/af_rose.c:int sysctl_rose_maximum_vcs = ROSE_DEFAULT_MAXVC;
With the following patch, rose_loopback_timer() attributes a VC number
within limits.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Not including net/atm/
Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Generated with the following semantic patch
@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)
@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)
applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The generic __sock_create function has a kern argument which allows the
security system to make decisions based on if a socket is being created by
the kernel or by userspace. This patch passes that flag to the
net_proto_family specific create function, so it can do the same thing.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Adds RCU management to the list of netdevices.
Convert some for_each_netdev() users to RCU version, if
it can avoid read_lock-ing dev_base_lock
Ie:
read_lock(&dev_base_loack);
for_each_netdev(net, dev)
some_action();
read_unlock(&dev_base_lock);
becomes :
rcu_read_lock();
for_each_netdev_rcu(net, dev)
some_action();
rcu_read_unlock();
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
All usages of structure net_proto_ops should be declared const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \ \
| | |/
| |/|
| | |
| | |
| | | |
Resolve the conflict between v2.6.32-rc7 where dn_def_dev_handler
gets a small bug fix and the sysctl tree where I am removing all
sysctl strategy routines.
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| | |
While hunting dev_put() for net-next-2.6, I found a device refcount
leak in ROSE, ioctl(SIOCADDRT) error path.
Fix is to not touch device refcount, as we hold RTNL
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Now that sys_sysctl is a compatiblity wrapper around /proc/sys
all sysctl strategy routines, and all ctl_name and strategy
entries in the sysctl tables are unused, and can be
revmoed.
In addition neigh_sysctl_register has been modified to no longer
take a strategy argument and it's callers have been modified not
to pass one.
Cc: "David Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This provides safety against negative optlen at the type
level instead of depending upon (sometimes non-trivial)
checks against this sprinkled all over the the place, in
each and every implementation.
Based upon work done by Arjan van de Ven and feedback
from Linus Torvalds.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
| |
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
| |
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| | |
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
arch/microblaze/include/asm/socket.h
|
| |
| |
| |
| |
| |
| |
| | |
rose_getname() can leak kernel memory to user.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \
| |/
| |
| |
| |
| |
| |
| |
| | |
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/iwlwifi/iwl-3945.h
drivers/net/wireless/iwlwifi/iwl-tx.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The use of a static buffer in rose2asc() to return its result is not
threadproof and can result in corruption if multiple threads are trying
to use one of the procfs files based on rose2asc().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
|
| |
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
commit 2b85a34e911bf483c27cfdd124aeb1605145dc80
(net: No more expensive sock_hold()/sock_put() on each tx)
changed initial sk_wmem_alloc value.
We need to take into account this offset when reporting
sk_wmem_alloc to user, in PROC_FS files or various
ioctls (SIOCOUTQ/TIOCOUTQ)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
commit 2b85a34e911bf483c27cfdd124aeb1605145dc80
(net: No more expensive sock_hold()/sock_put() on each tx)
changed initial sk_wmem_alloc value.
Some protocols check sk_wmem_alloc value to determine if a timer
must delay socket deallocation. We must take care of the sk_wmem_alloc
value being one instead of zero when no write allocations are pending.
Reported by Ingo Molnar, and full diagnostic from David Miller.
This patch introduces three helpers to get read/write allocations
and a followup patch will use these helpers to report correct
write allocations to user.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
| |
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit 244f46ae6e9e18f6fc0be7d1f49febde4762c34b.
Alan Cox did the research, and just like the other radio protocols
zero-length frames have meaning because at the top level ROSE is
X.25 PLP.
So this zero-length filtering is invalid.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
Otherwise we can wrap the sizes and end up sending garbage.
Closes #10423
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
| |
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
| |
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
|
| |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/hp-plus.c
drivers/net/wireless/ath5k/base.c
drivers/net/wireless/ath9k/recv.c
net/wireless/reg.c
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|\ \ \
| | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Since changeset e79ad711a0108475c1b3a03815527e7237020b08 from mainline,
>From David S. Miller,
empty packet can be transmitted on connected socket for datagram protocols.
However, this patch broke a high level application using ROSE network protocol with connected datagram.
Bulletin Board Stations perform bulletins forwarding between BBS stations via ROSE network using a forward protocol.
Now, if for some reason, a buffer in the application software happens to be empty at a specific moment,
ROSE sends an empty packet via unfiltered packet socket.
When received, this ROSE packet introduces perturbations of data exchange of BBS forwarding,
for the application message forwarding protocol is waiting for something else.
We agree that a more careful programming of the application protocol would avoid this situation and we are
willing to debug it.
But, as an empty frame is no use and does not have any meaning for ROSE protocol,
we may consider filtering zero length data both when sending and receiving socket data.
The proposed patch repaired BBS data exchange through ROSE network that were broken since 2.6.22.11 kernel.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
|
|
|
|
|
|
|
|
|
| |
The new address list lock needs to handle the same device layering
issues that the _xmit_lock one does.
This integrates work done by Patrick McHardy.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
Without CONFIG_NET_NS, namespace is always &init_net.
Compiler will be able to omit namespace comparisons with this patch.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
alloc_netdev_mq() now allocates an array of netdev_queue
structures for TX, based upon the queue_count argument.
Furthermore, all accesses to the TX queues are now vectored
through the netdev_get_tx_queue() and netdev_for_each_tx_queue()
interfaces. This makes it easy to grep the tree for all
things that want to get to a TX queue of a net device.
Problem spots which are not really multiqueue aware yet, and
only work with one queue, can easily be spotted by grepping
for all netdev_get_tx_queue() calls that pass in a zero index.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
| |
Accesses are mostly structured such that when there are multiple TX
queues the code transformations will be a little bit simpler.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ROSE network is organized through nodes connected via hamradio or Internet.
AX25 packet radio frames sent to a remote ROSE address destination are routed
through these nodes.
Without the present patch, automatic routing mechanism did not work optimally
due to an improper parameter checking.
rose_get_neigh() function is called either by rose_connect() or by
rose_route_frame().
In the case of a call from rose_connect(), f0 timer is checked to find if a connection
is already pending. In that case it returns the address of the neighbour, or returns a NULL otherwise.
When called by rose_route_frame() the purpose was to route a packet AX25 frame
through an adjacent node given a destination rose address.
However, in that case, t0 timer checked does not indicate if the adjacent node
is actually connected even if the timer is not null. Thus, for each frame sent, the
function often tried to start a new connexion even if the adjacent node was already connected.
The patch adds a "new" parameter that is true when the function is called by
rose route_frame().
This instructs rose_get_neigh() to check node parameter "restarted".
If restarted is true it means that the route to the destination address is opened via a neighbour
node already connected.
If "restarted" is false the function returns a NULL.
In that case the calling function will initiate a new connection as before.
This results in a fast routing of frames, from nodes to nodes, until
destination is reached, as originaly specified by ROSE protocole.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
This is the rose variant of changeset
9375cb8a1232d2a15fe34bec4d3474872e02faec
("ax25: Use sock_graft() and remove bogus sk_socket and sk_sleep init.")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
In rose_node_start() as well as in rose_node_stop() __acquires() and
spin_lock_bh() were wrongly passing rose_neigh_list_lock instead of
rose_node_list_lock arguments.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
[ INFO: possible recursive locking detected ]
2.6.25 #3
---------------------------------------------
ax25ipd/3811 is trying to acquire lock:
(rose_node_list_lock){-+..}, at: [<f8d31f1a>] rose_get_neigh+0x1a/0xa0
[rose]
but task is already holding lock:
(rose_node_list_lock){-+..}, at: [<f8d31fed>]
rose_route_frame+0x4d/0x620 [rose]
other info that might help us debug this:
6 locks held by ax25ipd/3811:
#0: (&tty->atomic_write_lock){--..}, at: [<c0259a1c>]
tty_write_lock+0x1c/0x50
#1: (rcu_read_lock){..--}, at: [<c02aea36>] net_rx_action+0x96/0x230
#2: (rcu_read_lock){..--}, at: [<c02ac5c0>] netif_receive_skb+0x100/0x2f0
#3: (rose_node_list_lock){-+..}, at: [<f8d31fed>]
rose_route_frame+0x4d/0x620 [rose]
#4: (rose_neigh_list_lock){-+..}, at: [<f8d31ff7>]
rose_route_frame+0x57/0x620 [rose]
#5: (rose_route_list_lock){-+..}, at: [<f8d32001>]
rose_route_frame+0x61/0x620 [rose]
stack backtrace:
Pid: 3811, comm: ax25ipd Not tainted 2.6.25 #3
[<c0147e27>] print_deadlock_bug+0xc7/0xd0
[<c0147eca>] check_deadlock+0x9a/0xb0
[<c0149cd2>] validate_chain+0x1e2/0x310
[<c0149b95>] ? validate_chain+0xa5/0x310
[<c010a7d8>] ? native_sched_clock+0x88/0xc0
[<c0149fa1>] __lock_acquire+0x1a1/0x750
[<c014a5d1>] lock_acquire+0x81/0xa0
[<f8d31f1a>] ? rose_get_neigh+0x1a/0xa0 [rose]
[<c03201a3>] _spin_lock_bh+0x33/0x60
[<f8d31f1a>] ? rose_get_neigh+0x1a/0xa0 [rose]
[<f8d31f1a>] rose_get_neigh+0x1a/0xa0 [rose]
[<f8d32404>] rose_route_frame+0x464/0x620 [rose]
[<c031ffdd>] ? _read_unlock+0x1d/0x20
[<f8d31fa0>] ? rose_route_frame+0x0/0x620 [rose]
[<f8d1c396>] ax25_rx_iframe+0x66/0x3b0 [ax25]
[<f8d1f42f>] ? ax25_start_t3timer+0x1f/0x40 [ax25]
[<f8d1e65b>] ax25_std_frame_in+0x7fb/0x890 [ax25]
[<c0320005>] ? _spin_unlock_bh+0x25/0x30
[<f8d1bdf6>] ax25_kiss_rcv+0x2c6/0x800 [ax25]
[<c02a4769>] ? sock_def_readable+0x59/0x80
[<c014a8a7>] ? __lock_release+0x47/0x70
[<c02a4769>] ? sock_def_readable+0x59/0x80
[<c031ffdd>] ? _read_unlock+0x1d/0x20
[<c02a4769>] ? sock_def_readable+0x59/0x80
[<c02a4d3a>] ? sock_queue_rcv_skb+0x13a/0x1d0
[<c02a4c45>] ? sock_queue_rcv_skb+0x45/0x1d0
[<f8d1bb30>] ? ax25_kiss_rcv+0x0/0x800 [ax25]
[<c02ac715>] netif_receive_skb+0x255/0x2f0
[<c02ac5c0>] ? netif_receive_skb+0x100/0x2f0
[<c02af05c>] process_backlog+0x7c/0xf0
[<c02aeb0c>] net_rx_action+0x16c/0x230
[<c02aea36>] ? net_rx_action+0x96/0x230
[<c012bd53>] __do_softirq+0x93/0x120
[<f8d2a68a>] ? mkiss_receive_buf+0x33a/0x3f0 [mkiss]
[<c012be37>] do_softirq+0x57/0x60
[<c012c265>] local_bh_enable_ip+0xa5/0xe0
[<c0320005>] _spin_unlock_bh+0x25/0x30
[<f8d2a68a>] mkiss_receive_buf+0x33a/0x3f0 [mkiss]
[<c025ea37>] pty_write+0x47/0x60
[<c025c620>] write_chan+0x1b0/0x220
[<c0259a1c>] ? tty_write_lock+0x1c/0x50
[<c011fec0>] ? default_wake_function+0x0/0x10
[<c0259bea>] tty_write+0x12a/0x1c0
[<c025c470>] ? write_chan+0x0/0x220
[<c018bbc6>] vfs_write+0x96/0x130
[<c0259ac0>] ? tty_write+0x0/0x1c0
[<c018c24d>] sys_write+0x3d/0x70
[<c0104d1e>] sysenter_past_esp+0x5f/0xa5
=======================
BUG: soft lockup - CPU#0 stuck for 61s! [ax25ipd:3811]
Pid: 3811, comm: ax25ipd Not tainted (2.6.25 #3)
EIP: 0060:[<c010a9db>] EFLAGS: 00000246 CPU: 0
EIP is at native_read_tsc+0xb/0x20
EAX: b404aa2c EBX: b404a9c9 ECX: 017f1000 EDX: 0000076b
ESI: 00000001 EDI: 00000000 EBP: ecc83afc ESP: ecc83afc
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
CR0: 8005003b CR2: b7f5f000 CR3: 2cd8e000 CR4: 000006f0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
[<c0204937>] delay_tsc+0x17/0x30
[<c02048e9>] __delay+0x9/0x10
[<c02127f6>] __spin_lock_debug+0x76/0xf0
[<c0212618>] ? spin_bug+0x18/0x100
[<c0147923>] ? __lock_contended+0xa3/0x110
[<c0212998>] _raw_spin_lock+0x68/0x90
[<c03201bf>] _spin_lock_bh+0x4f/0x60
[<f8d31f1a>] ? rose_get_neigh+0x1a/0xa0 [rose]
[<f8d31f1a>] rose_get_neigh+0x1a/0xa0 [rose]
[<f8d32404>] rose_route_frame+0x464/0x620 [rose]
[<c031ffdd>] ? _read_unlock+0x1d/0x20
[<f8d31fa0>] ? rose_route_frame+0x0/0x620 [rose]
[<f8d1c396>] ax25_rx_iframe+0x66/0x3b0 [ax25]
[<f8d1f42f>] ? ax25_start_t3timer+0x1f/0x40 [ax25]
[<f8d1e65b>] ax25_std_frame_in+0x7fb/0x890 [ax25]
[<c0320005>] ? _spin_unlock_bh+0x25/0x30
[<f8d1bdf6>] ax25_kiss_rcv+0x2c6/0x800 [ax25]
[<c02a4769>] ? sock_def_readable+0x59/0x80
[<c014a8a7>] ? __lock_release+0x47/0x70
[<c02a4769>] ? sock_def_readable+0x59/0x80
[<c031ffdd>] ? _read_unlock+0x1d/0x20
[<c02a4769>] ? sock_def_readable+0x59/0x80
[<c02a4d3a>] ? sock_queue_rcv_skb+0x13a/0x1d0
[<c02a4c45>] ? sock_queue_rcv_skb+0x45/0x1d0
[<f8d1bb30>] ? ax25_kiss_rcv+0x0/0x800 [ax25]
[<c02ac715>] netif_receive_skb+0x255/0x2f0
[<c02ac5c0>] ? netif_receive_skb+0x100/0x2f0
[<c02af05c>] process_backlog+0x7c/0xf0
[<c02aeb0c>] net_rx_action+0x16c/0x230
[<c02aea36>] ? net_rx_action+0x96/0x230
[<c012bd53>] __do_softirq+0x93/0x120
[<f8d2a68a>] ? mkiss_receive_buf+0x33a/0x3f0 [mkiss]
[<c012be37>] do_softirq+0x57/0x60
[<c012c265>] local_bh_enable_ip+0xa5/0xe0
[<c0320005>] _spin_unlock_bh+0x25/0x30
[<f8d2a68a>] mkiss_receive_buf+0x33a/0x3f0 [mkiss]
[<c025ea37>] pty_write+0x47/0x60
[<c025c620>] write_chan+0x1b0/0x220
[<c0259a1c>] ? tty_write_lock+0x1c/0x50
[<c011fec0>] ? default_wake_function+0x0/0x10
[<c0259bea>] tty_write+0x12a/0x1c0
[<c025c470>] ? write_chan+0x0/0x220
[<c018bbc6>] vfs_write+0x96/0x130
[<c0259ac0>] ? tty_write+0x0/0x1c0
[<c018c24d>] sys_write+0x3d/0x70
[<c0104d1e>] sysenter_past_esp+0x5f/0xa5
=======================
Since rose_route_frame() does not use rose_node_list we can safely
remove rose_node_list_lock spin lock here and let it be free for
rose_get_neigh().
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|