summaryrefslogtreecommitdiffstats
path: root/net/mac80211/ibss.c
Commit message (Collapse)AuthorAgeFilesLines
* mac80211: Send control port frames over nl80211Denis Kenzior2018-03-291-0/+1
| | | | | | | | | | | | If userspace requested control port frames to go over 80211, then do so. The control packets are intercepted just prior to delivery of the packet to the underlying network device. Pre-authentication type frames (protocol: 0x88c7) are also forwarded over nl80211. Signed-off-by: Denis Kenzior <denkenz@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: notify driver for change in multicast ratesPradeep Kumar Chitrapu2018-03-231-1/+1
| | | | | | | | | | | | With drivers implementing rate control in driver or firmware rate_control_send_low() may not get called, and thus the driver needs to know about changes in the multicast rate. Add and use a new BSS change flag for this. Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> [rewrite commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Convert timers to use timer_setup()Kees Cook2017-11-201-4/+3
| | | | | | | | | | | | | In preparation for unconditionally passing the struct timer_list pointer to all timer callbacks, switch to using the new timer_setup() and from_timer() to pass the timer pointer explicitly. Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* networking: introduce and use skb_put_data()Johannes Berg2017-06-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A common pattern with skb_put() is to just want to memcpy() some data into the new space, introduce skb_put_data() for this. An spatch similar to the one for skb_put_zero() converts many of the places using it: @@ identifier p, p2; expression len, skb, data; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_data(skb, data, len); | -p = (t)skb_put(skb, len); +p = skb_put_data(skb, data, len); ) ( p2 = (t2)p; -memcpy(p2, data, len); | -memcpy(p, data, len); ) @@ type t, t2; identifier p, p2; expression skb, data; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); ) ( p2 = (t2)p; -memcpy(p2, data, sizeof(*p)); | -memcpy(p, data, sizeof(*p)); ) @@ expression skb, len, data; @@ -memcpy(skb_put(skb, len), data, len); +skb_put_data(skb, data, len); (again, manually post-processed to retain some comments) Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mac80211: move clearing result into ieee80211_parse_ch_switch_ie()Johannes Berg2017-05-191-1/+0
| | | | | | | Clear the csa_ie in ieee80211_parse_ch_switch_ie() where the data is filled in, rather than in each caller. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix IBSS presp allocation sizeJohannes Berg2017-05-081-0/+2
| | | | | | | | | | | When VHT IBSS support was added, the size of the extra elements wasn't considered in ieee80211_ibss_build_presp(), which makes it possible that it would overrun the allocated buffer. Fix it by allocating the necessary space. Fixes: abcff6ef01f9 ("mac80211: add VHT support for IBSS") Reported-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Fix possible sband related NULL pointer de-referenceMohammed Shafi Shajakhan2017-04-281-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even if the channel context configuration is NULL. This crashes for chipsets which support 5 Ghz alone when it tries to access members of 'sband'. Channel context configuration can be NULL in multivif case and when channel switch is in progress (or) when it fails. Fix this by replacing the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which returns a NULL pointer for sband when the channel configuration is NULL. An example scenario is as below: In multivif mode (AP + STA) with drivers like ath10k, when we do a channel switch in the AP vif (which has a number of clients connected) and a STA vif which is connected to some other AP, when the channel switch in AP vif fails, while the STA vifs tries to connect to the other AP, there is a window where the channel context is NULL/invalid and this results in a crash while the clients connected to the AP vif tries to reconnect and this race is very similar to the one investigated by Michal in https://patchwork.kernel.org/patch/3788161/ and this does happens with hardware that supports 5Ghz alone after long hours of testing with continuous channel switch on the AP vif ieee80211 phy0: channel context reservation cannot be finalized because some interfaces aren't switching wlan0: failed to finalize CSA, disconnecting wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice (Reason: 3=DEAUTH_LEAVING) WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211] [<bf77272c>] (sta_info_alloc [mac80211]) [<bf78776c>] (ieee80211_add_station [mac80211])) [<bf73cc50>] (nl80211_new_station [cfg80211]) Unable to handle kernel NULL pointer dereference at virtual address 00000014 pgd = d5f4c000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM PC is at sta_info_alloc+0x380/0x3fc [mac80211] LR is at sta_info_alloc+0x37c/0x3fc [mac80211] [<bf772738>] (sta_info_alloc [mac80211]) [<bf78776c>] (ieee80211_add_station [mac80211]) [<bf73cc50>] (nl80211_new_station [cfg80211])) Cc: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: separate encoding/bandwidth from flagsJohannes Berg2017-04-281-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We currently use a lot of flags that are mutually incompatible, separate this out into actual encoding and bandwidth enum values. Much of this again done with spatch, with manual post-editing, mostly to add the switch statements and get rid of the conversions. @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_80MHZ +status->bw = RATE_INFO_BW_80 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_40MHZ +status->bw = RATE_INFO_BW_40 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_20MHZ +status->bw = RATE_INFO_BW_20 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_160MHZ +status->bw = RATE_INFO_BW_160 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_5MHZ +status->bw = RATE_INFO_BW_5 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_10MHZ +status->bw = RATE_INFO_BW_10 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_VHT +status->encoding = RX_ENC_VHT @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_HT +status->encoding = RX_ENC_HT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_VHT +status.encoding = RX_ENC_VHT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_HT +status.encoding = RX_ENC_HT @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_HT) +(status->encoding == RX_ENC_HT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_VHT) +(status->encoding == RX_ENC_VHT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_5MHZ) +(status->bw == RATE_INFO_BW_5) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_10MHZ) +(status->bw == RATE_INFO_BW_10) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_40MHZ) +(status->bw == RATE_INFO_BW_40) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_80MHZ) +(status->bw == RATE_INFO_BW_80) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_160MHZ) +(status->bw == RATE_INFO_BW_160) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: clean up rate encoding bits in RX statusJohannes Berg2017-04-281-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In preparation for adding support for HE rates, clean up the driver report encoding for rate/bandwidth reporting on RX frames. Much of this patch was done with the following spatch: @@ expression status; @@ -status->flag & (RX_FLAG_HT | RX_FLAG_VHT) +status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT) @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORTPRE +status->enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status->flag & RX_FLAG_SHORTPRE +status->enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT +status->enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status->flag & RX_FLAG_HT +status->enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_40MHZ +status->enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status->flag & RX_FLAG_40MHZ +status->enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORT_GI +status->enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status->flag & RX_FLAG_SHORT_GI +status->enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT_GF +status->enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status->flag & RX_FLAG_HT_GF +status->enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_VHT +status->enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status->flag & RX_FLAG_VHT +status->enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_STBC_MASK +status->enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status->flag & RX_FLAG_STBC_MASK +status->enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_LDPC +status->enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status->flag & RX_FLAG_LDPC +status->enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_10MHZ +status->enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status->flag & RX_FLAG_10MHZ +status->enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_5MHZ +status->enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status->flag & RX_FLAG_5MHZ +status->enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_80MHZ +status->enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_80MHZ +status->enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_160MHZ +status->enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_160MHZ +status->enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_BF +status->enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_BF +status->enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status->flag op STBC << RX_FLAG_STBC_SHIFT +status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORTPRE +status.enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status.flag & RX_FLAG_SHORTPRE +status.enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT +status.enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status.flag & RX_FLAG_HT +status.enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_40MHZ +status.enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status.flag & RX_FLAG_40MHZ +status.enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORT_GI +status.enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status.flag & RX_FLAG_SHORT_GI +status.enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT_GF +status.enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status.flag & RX_FLAG_HT_GF +status.enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_VHT +status.enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status.flag & RX_FLAG_VHT +status.enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_STBC_MASK +status.enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status.flag & RX_FLAG_STBC_MASK +status.enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_LDPC +status.enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status.flag & RX_FLAG_LDPC +status.enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_10MHZ +status.enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status.flag & RX_FLAG_10MHZ +status.enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_5MHZ +status.enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status.flag & RX_FLAG_5MHZ +status.enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_80MHZ +status.enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_80MHZ +status.enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_160MHZ +status.enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_160MHZ +status.enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_BF +status.enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_BF +status.enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status.flag op STBC << RX_FLAG_STBC_SHIFT +status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ @@ -RX_FLAG_STBC_SHIFT +RX_ENC_FLAG_STBC_SHIFT Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: ibss: Fix channel type enum in ieee80211_sta_join_ibss()Matthias Kaehlcke2017-04-181-2/+2
| | | | | | | | | | | cfg80211_chandef_create() expects an 'enum nl80211_channel_type' as channel type however in ieee80211_sta_join_ibss() NL80211_CHAN_WIDTH_20_NOHT is passed in two occasions, which is of the enum type 'nl80211_chan_width'. Change the value to NL80211_CHAN_NO_HT (20 MHz, non-HT channel) of the channel type enum. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix CSA in IBSS modeKoen Vandeputte2017-02-091-2/+2
| | | | | | | | | | | Add the missing IBSS capability flag during capability init as it needs to be inserted into the generated beacon in order for CSA to work. Fixes: cd7760e62c2ac ("mac80211: add support for CSA in IBSS mode") Signed-off-by: Piotr Gawlowicz <gawlowicz@tkn.tu-berlin.de> Signed-off-by: Mikołaj Chwalisz <chwalisz@tkn.tu-berlin.de> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211: remove enum ieee80211_bandJohannes Berg2016-04-121-5/+5
| | | | | | | | | This enum is already perfectly aliased to enum nl80211_band, and the only reason for it is that we get IEEE80211_NUM_BANDS out of it. There's no really good reason to not declare the number of bands in nl80211 though, so do that and remove the cfg80211 one. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add separate last_ack variableJohannes Berg2016-04-061-5/+8
| | | | | | | | | | | Instead of touching the rx_stats.last_rx from the status path, introduce and use a status_stats.last_ack variable. This will make rx_stats.last_rx indicate when the last frame was received, making it available for real "last_rx" and statistics gathering; statistics, when done per-CPU, will need to figure out which place was updated last for those items where the "last" value is exposed. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: remove rx_stats.last_rx update after sta allocJohannes Berg2016-04-061-4/+0
| | | | | | | There's no need to update rx_stats.last_rx after allocating a station since it's already updated during allocation. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge tag 'mac80211-next-for-davem-2016-02-26' of ↵David S. Miller2016-03-011-13/+19
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== Here's another round of updates for -next: * big A-MSDU RX performance improvement (avoid linearize of paged RX) * rfkill changes: cleanups, documentation, platform properties * basic PBSS support in cfg80211 * MU-MIMO action frame processing support * BlockAck reordering & duplicate detection offload support * various cleanups & little fixes ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * mac80211: fix ibss scan parametersSara Sharon2016-02-241-7/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When joining IBSS a full scan should be initiated in order to search for existing cell, unless the fixed_channel parameter was set. A default channel to create the IBSS on if no cell was found is provided as well. However - a scan is initiated only on the default channel provided regardless of whether ifibss->fixed_channel is set or not, with the obvious result of the cell not joining existing IBSS cell that is on another channel. Fixes: 76bed0f43b27 ("mac80211: IBSS fix scan request") Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: refactor HT/VHT to chandef codeJohannes Berg2016-02-241-6/+4
| | | | | | | | | | | | | | | | | | The station MLME and IBSS/mesh ones use entirely different code for interpreting HT and VHT operation elements. Change the code that interprets them a bit - it now modifies an existing chandef - and use it also in the MLME code. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: Requeue work after scan complete for all VIF types.Sachin Kulkarni2016-01-261-1/+0
|/ | | | | | | | | | | | | | During a sw scan ieee80211_iface_work ignores work items for all vifs. However after the scan complete work is requeued only for STA, ADHOC and MESH iftypes. This occasionally results in event processing getting delayed/not processed for iftype AP when it coexists with a STA. This can result in data halt and eventually disconnection on the AP interface. Cc: stable@vger.kernel.org Signed-off-by: Sachin Kulkarni <Sachin.Kulkarni@imgtec.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Allow a STA to join an IBSS with 80+80 MHz channelJouni Malinen2015-12-041-0/+1
| | | | | | | | | While it was possible to create an IBSS with 80+80 MHz channel, joining such an IBSS resulted in falling back to 20 MHz channel with VHT disabled due to a missing switch case for 80+80. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: make enable_qos parameter to ieee80211_set_wmm_default()Johannes Berg2015-11-031-1/+1
| | | | | | | | The function currently determines this value, for use in bss_info.qos, based on the interface type itself. Make it a parameter instead and set it with the same logic for now. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: TDLS: add proper HT-oper IEArik Nemtsov2015-11-031-1/+1
| | | | | | | | | | | When 11n peers performs a TDLS connection on a legacy BSS, the HT operation IE must be specified according to IEEE802.11-2012 section 9.23.3.2. Otherwise HT-protection is compromised and the medium becomes noisy for both the TDLS and the BSS links. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: move station statistics into sub-structsJohannes Berg2015-10-211-6/+7
| | | | | | | | | | | | | | Group station statistics by where they're (mostly) updated (TX, RX and TX-status) and group them into sub-structs of the struct sta_info. Also rename the variables since the grouping now makes it obvious where they belong. This makes it easier to identify where the statistics are updated in the code, and thus easier to think about them. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: use new cfg80211_inform_bss_frame_data() APIJohannes Berg2015-10-131-5/+6
| | | | | | | The new API is more easily extensible with a metadata struct passed to it, use it in mac80211. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix the beacon csa counter for mesh and ibssChun-Yeow Yeoh2015-06-091-0/+1
| | | | | | | | | The csa counter has moved from sdata to beacon/presp but it is not updated accordingly for mesh and ibss. Fix this. Fixes: af296bdb8da4 ("mac80211: move csa counters from sdata to beacon/presp") Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: check fast-xmit if IBSS STA QoS changedJohannes Berg2015-05-111-1/+4
| | | | | | | | | When an IBSS station gets QoS enabled after having been added, check fast-xmit to make sure the QoS header gets added to the cache properly and frames can go out with QoS and higher rates. Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge tag 'mac80211-next-for-davem-2015-03-30' of ↵David S. Miller2015-03-311-121/+220
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== Lots of updates for net-next; along with the usual flurry of small fixes, cleanups and internal features we have: * VHT support for TDLS and IBSS (conditional on drivers though) * first TX performance improvements (the biggest will come later) * many suspend/resume (race) fixes * name_assign_type support from Tom Gundersen ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * mac80211: add VHT support for IBSSJanusz.Dziedzic@tieto.com2015-03-301-9/+40
| | | | | | | | | | | | | | | | | | Add VHT support for IBSS. Drivers could activate this feature by setting NL80211_EXT_FEATURE_VHT_IBSS flag. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: IBSS fix scan requestJanusz.Dziedzic@tieto.com2015-03-301-2/+79
| | | | | | | | | | | | | | | | | | | | In case of wide bandwidth (wider than 20MHz) used by IBSS, scan all channels in chandef to be able to find neighboring IBSS netwqworks that use the same overall channels but a different control channel. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: make sta.wme indicate whether QoS is usedJohannes Berg2015-03-301-1/+1
| | | | | | | | | | | | | | | | | | Indicating just the peer's capability is fairly pointless if the local device doesn't support it. Make the variable track both combined, and remove the 'local support' check in the TX path. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: remove drop_unencrypted codeJohannes Berg2015-03-201-4/+0
| | | | | | | | | | | | | | | | | | | | This mechanism was historic, and only ever used by IBSS, which also doesn't need to have it as it properly manages station's 802.1X PAE state (or, with WEP, always has a key.) Remove the mechanism to clean up the code. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * mac80211: IBSS: refactor ieee80211_rx_bss_infoJanusz.Dziedzic@tieto.com2015-03-171-85/+99
| | | | | | | | | | | | | | | | Put station specific code in ieee80211_update_sta_info function. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
| * cfg80211: add bss_type and privacy arguments in cfg80211_get_bss()Dedy Lansky2015-03-031-31/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 802.11ad adds new a network type (PBSS) and changes the capability field interpretation for the DMG (60G) band. The same 2 bits that were interpreted as "ESS" and "IBSS" before are re-used as a 2-bit field with 3 valid values (and 1 reserved). Valid values are: "IBSS", "PBSS" (new) and "AP". In order to get the BSS struct for the new PBSS networks, change the cfg80211_get_bss() function to take a new enum ieee80211_bss_type argument with the valid network types, as "capa_mask" and "capa_val" no longer work correctly (the search must be band-aware now.) The remaining bits in "capa_mask" and "capa_val" are used only for privacy matching so replace those two with a privacy enum as well. Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> [rewrite commit log, tiny fixes] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | mac80211: Use eth_<foo>_addr instead of memsetJoe Perches2015-03-031-1/+1
|/ | | | | | | Use the built-in function instead of memset. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mac80211: notify NSS changed when IBSS and HTJanusz Dziedzic2014-12-171-2/+9
| | | | | | | | | When using IBSS in HT mode, we always get NSS=1 in rc_update callback. Force NSS recalculation when rates updated and notify driver that NSS changed. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: use secondary channel offset IE also beacons during CSALuciano Coelho2014-10-291-1/+1
| | | | | | | | | | | | | | | | | | | | | If we are switching from an HT40+ to an HT40- channel (or vice-versa), we need the secondary channel offset IE to specify what is the post-CSA offset to be used. This applies both to beacons and to probe responses. In ieee80211_parse_ch_switch_ie() we were ignoring this IE from beacons and using the *current* HT information IE instead. This was causing us to use the same offset as before the switch. Fix that by using the secondary channel offset IE also for beacons and don't ever use the pre-switch offset. Additionally, remove the "beacon" argument from ieee80211_parse_ch_switch_ie(), since it's not needed anymore. Cc: stable@vger.kernel.org Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add Intel Mobile Communications copyrightJohannes Berg2014-09-051-0/+1
| | | | | | | | | | | | | Our legal structure changed at some point (see wikipedia), but we forgot to immediately switch over to the new copyright notice. For files that we have modified in the time since the change, add the proper copyright notice now. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: don't duplicate station QoS capability dataJohannes Berg2014-08-151-1/+1
| | | | | | | | | | | | | We currently track the QoS capability twice: for all peer stations in the WLAN_STA_WME flag, and for any clients associated to an AP interface separately for drivers in the sta->sta.wme field. Remove the WLAN_STA_WME flag and track the capability only in the driver-visible field, getting rid of the limitation that the field is only valid in AP mode. Reviewed-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add QoS IE during TDLS setup startArik Nemtsov2014-07-211-11/+2
| | | | | | | | | | | | If QoS is supported by the card, add an appropriate IE to TDLS setup- request and setup-response frames. Consolidate the setting of the WMM info IE across mac80211. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: Liad Kaufman <liad.kaufman@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: move csa counters from sdata to beacon/prespMichal Kazior2014-06-231-1/+1
| | | | | | | | | | | | | | | Having csa counters part of beacon and probe_resp structures makes it easier to get rid of possible races between setting a beacon and updating counters on SMP systems by guaranteeing counters are always consistent against given beacon struct. While at it relax WARN_ON into WARN_ON_ONCE to prevent spamming logs and racing. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> [remove pointless array check] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: fix IBSS join by initializing last_scan_completedKrzysztof Hałasa2014-05-271-0/+1
| | | | | | | | | | | Without this fix, freshly rebooted Linux creates a new IBSS instead of joining an existing one. Only when jiffies counter overflows after 5 minutes the IBSS can be successfully joined. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> [edit commit message slightly] Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: Support multiple CSA countersAndrei Otcheretianski2014-05-151-1/+1
| | | | | | | | | | Support up to IEEE80211_MAX_CSA_COUNTERS_NUM csa counters. This is defined to be 2 now, to support both CSA and eCSA counters. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211/mac80211: move combination check to mac80211 for ibssLuciano Coelho2014-04-091-3/+29
| | | | | | | | Now that mac80211 can check the interface combinations itself, move the combinations check from cfg80211 to mac80211 when joining an IBSS. Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211/mac80211: refactor cfg80211_chandef_dfs_required()Luciano Coelho2014-04-091-16/+16
| | | | | | | | | Some interface types don't require DFS (such as STATION, P2P_CLIENT etc). In order to centralize these decisions, make cfg80211_chandef_dfs_required() take the iftype into consideration. Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211: Enable GO operation on additional channelsIlan Peer2014-04-091-3/+6
| | | | | | | | | | | | | | | | | | | | | Allow GO operation on a channel marked with IEEE80211_CHAN_GO_CONCURRENT iff there is an active station interface that is associated to an AP operating on the same channel in the 2 GHz band or the same UNII band (in the 5 GHz band). This relaxation is not allowed if the channel is marked with IEEE80211_CHAN_RADAR. Note that this is a permissive approach to the FCC definitions, that require a clear assessment that the device operating the AP is an authorized master, i.e., with radar detection and DFS capabilities. It is assumed that such restrictions are enforced by user space. Furthermore, it is assumed, that if the conditions that allowed for the operation of the GO on such a channel change, i.e., the station interface disconnected from the AP, it is the responsibility of user space to evacuate the GO from the channel. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: use RCU_INIT_POINTERMonam Agarwal2014-04-091-1/+1
| | | | | | | | | | | rcu_assign_pointer() ensures that the initialization of a structure is carried out before storing a pointer to that structure. However, in the case that NULL is assigned there's no structure to initialize so using RCU_INIT_POINTER instead is safe and more efficient. Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com> [squash eight tiny patches, rewrite commit log] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211/mac80211: ignore signal if the frame was heard on wrong channelEmmanuel Grumbach2014-03-191-10/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On 2.4Ghz band, the channels overlap since the delta between different channels is 5Mhz while the width of the receiver is 20Mhz (at least). This means that we can hear beacons or probe responses from adjacent channels. These frames will have a significant lower RSSI which will feed all kinds of logic with inaccurate data. An obvious example is the roaming algorithm that will think our AP is getting weak and will try to move to another AP. In order to avoid this, update the signal only if the frame has been heard on the same channel as the one advertised by the AP in its DS / HT IEs. We refrain from updating the values only if the AP is already in the BSS list so that we will still have a valid (but inaccurate) value if the AP was heard on an adjacent channel only. To achieve this, stop taking the channel from DS / HT IEs in mac80211. The DS / HT IEs is taken into account to discard the frame if it was received on a disabled channel. This can happen due to the same phenomenon: the frame is sent on channel 12, but heard on channel 11 while channel 12 can be disabled on certain devices. Since this check is done in cfg80211, stop even checking this in mac80211. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> [remove unused rx_freq variable] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: ibss: handle cfg80211_chandef_dfs_required() error codesLuciano Coelho2014-02-211-0/+5
| | | | | | | | | Error codes returned by cfg80211_chandef_dfs_required() are ignored when trying to join an IBSS. Fix this by printing an error and returning. Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge branch 'master' of ↵John W. Linville2014-02-131-4/+1
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
| * mac80211: Fix IBSS disconnectSujith Manoharan2014-02-061-4/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, when a station leaves an IBSS network, the corresponding BSS is not dropped from cfg80211 if there are other active stations in the network. But, the small window that is present when trying to determine a station's status based on IEEE80211_IBSS_MERGE_INTERVAL introduces a race. Instead of trying to keep the BSS, always remove it when leaving an IBSS network. There is not much benefit to retain the BSS entry since it will be added with a subsequent join operation. This fixes an issue where a dangling BSS entry causes ath9k to wait for a beacon indefinitely. Cc: <stable@vger.kernel.org> Reported-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | cfg80211: fix channel configuration in IBSS joinAntonio Quartulli2014-02-041-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When receiving an IBSS_JOINED event select the BSS object based on the {bssid, channel} couple rather than the bssid only. With the current approach if another cell having the same BSSID (but using a different channel) exists then cfg80211 picks up the wrong BSS object. The result is a mismatching channel configuration between cfg80211 and the driver, that can lead to any sort of problem. The issue can be triggered by having an IBSS sitting on given channel and then asking the driver to create a new cell using the same BSSID but with a different frequency. By passing the channel to cfg80211_get_bss() we can solve this ambiguity and retrieve/create the correct BSS object. All the users of cfg80211_ibss_joined() have been changed accordingly. Moreover WARN when cfg80211_ibss_joined() gets a NULL channel as argument and remove a bogus call of the same function in ath6kl (it does not make sense to call cfg80211_ibss_joined() with a zero BSSID on ibss-leave). Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: Bing Zhao <bzhao@marvell.com> Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi> Cc: libertas-dev@lists.infradead.org Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> [minor code cleanup in ath6kl] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
OpenPOWER on IntegriCloud