summaryrefslogtreecommitdiffstats
path: root/net/batman-adv
Commit message (Collapse)AuthorAgeFilesLines
* batman-adv: fix batman-adv header overhead calculationMarek Lindner2014-01-151-1/+1
| | | | | | | | | | | | | | Batman-adv prepends a full ethernet header in addition to its own header. This has to be reflected in the MTU calculation, especially since the value is used to set dev->hard_header_len. Introduced by 411d6ed93a5d0601980d3e5ce75de07c98e3a7de ("batman-adv: consider network coding overhead when calculating required mtu") Reported-by: cmsv <cmsv@wirelesspt.net> Reported-by: Martin Hundebøll <martin@hundeboll.net> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: fix vlan header accessAntonio Quartulli2013-12-281-1/+1
| | | | | | | | | | | | When batadv_get_vid() is invoked in interface_rx() the batman-adv header has already been removed, therefore the header_len argument has to be 0. Introduced by c018ad3de61a1dc4194879a53e5559e094aa7b1a ("batman-adv: add the VLAN ID attribute to the TT entry") Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
* batman-adv: clean nf state when removing protocol headerAntonio Quartulli2013-12-281-0/+5
| | | | | | | | | | | | | | | | | | | | | | | If an interface enslaved into batman-adv is a bridge (or a virtual interface built on top of a bridge) the nf_bridge member of the skbs reaching the soft-interface is filled with the state about "netfilter bridge" operations. Then, if one of such skbs is locally delivered, the nf_bridge member should be cleaned up to avoid that the old state could mess up with other "netfilter bridge" operations when entering a second bridge. This is needed because batman-adv is an encapsulation protocol. However at the moment skb->nf_bridge is not released at all leading to bogus "netfilter bridge" behaviours. Fix this by cleaning the netfilter state of the skb before it gets delivered to the upper layer in interface_rx(). Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
* batman-adv: fix alignment for batadv_tvlv_tt_changeAntonio Quartulli2013-12-282-4/+6
| | | | | | | | Make struct batadv_tvlv_tt_change a multiple 4 bytes long to avoid padding on any architecture. Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
* batman-adv: fix size of batadv_bla_claim_dstSimon Wunderlich2013-12-281-0/+2
| | | | | | | | | Since this is a mac address and always 48 bit, and we can assume that it is always aligned to 2-byte boundaries, add a pack(2) pragma. Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: fix size of batadv_icmp_headerAntonio Quartulli2013-12-283-14/+44
| | | | | | | | | | | | | struct batadv_icmp_header currently has a size of 17, which will be padded to 20 on some architectures. Fix this by unrolling the header into the parent structures. Moreover keep the ICMP parsing functions as generic as they are now by using a stub icmp_header struct during packet parsing. Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
* batman-adv: fix header alignment by unrolling batadv_headerSimon Wunderlich2013-12-2810-85/+118
| | | | | | | | | | | | The size of the batadv_header of 3 is problematic on some architectures which automatically pad all structures to a 32 bit boundary. To not lose performance by packing this struct, better embed it into the various host structures. Reported-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: fix alignment for batadv_coded_packetSimon Wunderlich2013-12-281-2/+2
| | | | | | | | | | The compiler may decide to pad the structure, and then it does not have the expected size of 46 byte. Fix this by moving it in the pragma pack(2) part of the code. Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: generalize batman-adv icmp packet handlingSimon Wunderlich2013-10-235-97/+157
| | | | | | | | | | | | | | | | Instead of handling icmp packets only up to length of icmp_packet_rr, the code should handle any icmp length size. Therefore the length truncating is moved to when the packet is actually sent to userspace (this does not support lengths longer than icmp_packet_rr yet). Longer packets are forwarded without truncating. This patch also cleans up some parts where the icmp header struct could be used instead of other icmp_packet(_rr) structs to make the code more readable. Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: Start new development cycleSimon Wunderlich2013-10-231-1/+1
| | | | | Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: include the sync-flags when compute the global/local table CRCAntonio Quartulli2013-10-233-2/+28
| | | | | | | | | | | | | | | | | | | | | | Flags covered by TT_SYNC_MASK are kept in sync among the nodes in the network and therefore they have to be considered while computing the global/local table CRC. In this way a generic originator is able to understand if its table contains the correct flags or not. Bits from 4 to 7 in the TT flags fields are now reserved for "synchronized" flags only. This allows future developers to add more flags of this type without breaking compatibility. It's important to note that not all the remote TT flags are synchronised. This comes from the fact that some flags are used to inject an information once only. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
* batman-adv: improve the TT component to support runtime flag changesAntonio Quartulli2013-10-232-1/+30
| | | | | | | | | | | | | | | | Some flags (i.e. the WIFI flag) may change after that the related client has already been announced. However it is useful to informa the rest of the network about this change. Add a runtime-flag-switch detection mechanism and re-announce the related TT entry to advertise the new flag value. This mechanism can be easily exploited by future flags that may need the same treatment. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
* batman-adv: invoke dev_get_by_index() outside of is_wifi_iface()Antonio Quartulli2013-10-233-31/+12
| | | | | | | | | | | | Upcoming changes need to perform other checks on the incoming net_device struct. To avoid performing dev_get_by_index() for each and every check, it is better to move it outside of is_wifi_iface() and search the netdev object once only. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
* batman-adv: send GW_DEL event in case of soft-iface destructionAntonio Quartulli2013-10-231-2/+7
| | | | | | | | | | In case of soft_iface destruction send a GW DEL event to userspace so that applications which are listening for GW events are informed about the lost of connectivity and can react accordingly. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
* batman-adv: limit local translation table max sizeMarek Lindner2013-10-235-36/+173
| | | | | | | | | | | | | | | The local translation table size is limited by what can be transferred from one node to another via a full table request. The number of entries fitting into a full table request depend on whether the fragmentation is enabled or not. Therefore this patch introduces a max table size check and refuses to add more local clients when that size is reached. Moreover, if the max full table packet size changes (MTU change or fragmentation is disabled) the local table is downsized instantaneously. Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Antonio Quartulli <ordex@autistici.org>
* batman-adv: adapt the TT component to use the new API functionsAntonio Quartulli2013-10-231-11/+24
| | | | | Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: provide orig_node routing APIAntonio Quartulli2013-10-233-88/+151
| | | | | | | | | | | | | | | | | | | | | Some operations executed on an orig_node depends on the current routing algorithm being used. To easily make this mechanism routing algorithm agnostic add a orig_node specific API that each algorithm can populate with its own routines. Such routines are then invoked by the code when needed, without knowing which routing algorithm is currently in use With this patch 3 API functions are added: - orig_free (to free routing depending internal structs) - orig_add_if (to change the inner state of an orig_node when a new hard interface is added) - orig_del_if (to change the inner state of an orig_node when an hard interface is removed) Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: adapt the neighbor purging routine to use the new API functionsAntonio Quartulli2013-10-231-8/+9
| | | | | Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: adapt bonding to use the new API functionsAntonio Quartulli2013-10-233-15/+32
| | | | | Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: add bat_neigh_is_equiv_or_better API functionAntonio Quartulli2013-10-234-1/+30
| | | | | | | | | | | | Each routing protocol has its own metric semantic and therefore is the protocol itself the only component able to compare two metrics to check their "similarity". This new API allows each routing protocol to implement its own logic and make the external code protocol agnostic. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: add bat_neigh_cmp API functionAntonio Quartulli2013-10-233-1/+25
| | | | | | | | | This new API allows to compare the two neighbours based on the metric avoiding the user to deal with any routing algorithm specific detail Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: add bat_orig_print API functionAntonio Quartulli2013-10-233-56/+78
| | | | | | | | | | | | Each routing protocol has its own metric and private variables, therefore it is useful to introduce a new API for originator information printing. This API needs to be implemented by each protocol in order to provide its specific originator table output. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: make struct batadv_orig_node algorithm agnosticAntonio Quartulli2013-10-234-95/+135
| | | | | | | | | | some of the struct batadv_orig_node members are B.A.T.M.A.N. IV specific and therefore they are moved in a algorithm specific substruct in order to make batadv_orig_node routing algorithm agnostic Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: make struct batadv_neigh_node algorithm agnosticAntonio Quartulli2013-10-238-71/+103
| | | | | | | | | | some of the fields in struct batadv_neigh_node are strictly related to the B.A.T.M.A.N. IV algorithm. In order to make the struct usable by any routing algorithm it has to be split and made more generic Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: make the backbone gw check VLAN specificAntonio Quartulli2013-10-193-43/+27
| | | | | | | | | | | | | | | | | | | | | The backbone gw check has to be VLAN specific so that code using it can specify VID where the check has to be done. In the TT code, the check has been moved into the tt_global_add() function so that it can be performed on a per-entry basis instead of ignoring all the TT data received from another backbone node. Only TT global entries belonging to the VLAN where the backbone node is connected to are skipped. All the other spots where the TT code was checking whether a node is a backbone have been removed. Moreover, batadv_bla_is_backbone_gw_orig() now returns bool since it used to return only 1 or 0. Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: make the TT global purge routine VLAN specificAntonio Quartulli2013-10-195-6/+21
| | | | | | | | | | | | | | | | | | | Instead of unconditionally removing all the TT entries served by a given originator, make tt_global_orig_del() remove only entries matching a given VLAN identifier provided as argument. If such argument is negative all the global entries served by the originator are removed. This change is used into the BLA code to purge entries served by a newly discovered Backbone node, but limiting the operation only to those connected to the VLAN where the backbone has been discovered. Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: make the TT CRC logic VLAN specificAntonio Quartulli2013-10-195-157/+730
| | | | | | | | | | | | | | | | | | | | | | | | | | | This change allows nodes to handle the TT table on a per-VLAN basis. This is needed because nodes may have to store only some of the global entries advertised by another node. In this scenario such nodes would re-create only a partial global table and would not be able to compute a correct CRC anymore. This patch splits the logic and introduces one CRC per VLAN. In this way a node fetching only some entries belonging to some VLANs is still able to compute the needed CRCs and still check the table correctness. With this patch the shape of the TVLV-TT is changed too because now a node needs to advertise all the CRCs of all the VLANs that it is wired to. The debug output of the local Translation Table now shows the CRC along with each entry since there is not a common value for the entire table anymore. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: lock around TT operations to avoid sending inconsistent dataAntonio Quartulli2013-10-194-4/+34
| | | | | | | | | | | | | | | | | | | | A TT response may be prepared and sent while the local or global translation table is getting updated. The worst case is when one of the tables is accessed after its content has been recently updated but the metadata (TTVN/CRC) has not yet. In this case the reader will get a table content which does not match the TTVN/CRC. This will lead to an inconsistent state and so to a TT recovery. To avoid entering this situation, put a lock around those TT operations recomputing the metadata and around the TT Response creation (the latter is the only reader that accesses the metadata together with the table). Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: remove bogus commentAntonio Quartulli2013-10-191-5/+0
| | | | | | | | this comment refers to the old batmand codebase and does not make sense anymore. Remove it Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: refine API calls for unicast transmissions of SKBsLinus Lüssing2013-10-194-48/+108
| | | | | | | | | | | | | | | | | | | With this patch the functions batadv_send_skb_unicast() and batadv_send_skb_unicast_4addr() are further refined into batadv_send_skb_via_tt(), batadv_send_skb_via_tt_4addr() and batadv_send_skb_via_gw(). This way we avoid any "guessing" about where to send a packet in the unicast forwarding methods and let the callers decide. This is going to be useful for the upcoming multicast related patches in particular. Further, the return values were polished a little to use the more appropriate NET_XMIT_* defines. Signed-off-by: Linus Lüssing <linus.luessing@web.de> Acked-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: make the AP isolation attribute VLAN specificAntonio Quartulli2013-10-195-14/+30
| | | | | | | | | | AP isolation has to be enabled on one VLAN interface only. This patch moves the AP isolation attribute to the per-vlan interface attribute set, enabling it to have a different value depending on the selected vlan. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: add sysfs framework for VLANAntonio Quartulli2013-10-194-3/+198
| | | | | | | | | | | | | | | | | | | Each VLAN can now have its own set of attributes which are exported through a new subfolder in the sysfs tree. Each VLAN created on top of a soft_iface will have its own subfolder. The subfolder is named "vlan%VID" and it is created inside the "mesh" sysfs folder belonging to batman-adv. Attributes corresponding to the untagged LAN are stored in the root sysfs folder as before. This patch also creates all the needed macros and data structures to easily handle new VLAN spacific attributes. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: add per VLAN interface attribute frameworkAntonio Quartulli2013-10-195-3/+197
| | | | | | | | | | | | | | | | | | | Since batman-adv is now fully VLAN-aware, a proper framework able to handle per-vlan-interface attributes is needed. Those attributes will affect the associated VLAN interface only, rather than the real soft_iface (which would result in every vlan interface having the same attribute configuration). To make the code simpler and easier to extend, attributes associated to the standalone soft_iface are now treated like belonging to yet another vlan having a special vid. This vid is different from the others because it is made up by all zeros and the VLAN_HAS_TAG bit is not set. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: make the Distributed ARP Table vlan awareAntonio Quartulli2013-10-192-48/+107
| | | | | | | | | | | The same IP subnet can be used on different VLANs, therefore DAT has to differentiate whether the IP to resolve belongs to one or the other virtual LAN. To accomplish this task DAT has to deal with the VLAN tag and store it together with each ARP entry. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: make the GW module correctly talk to the new VLAN-TTAntonio Quartulli2013-10-191-3/+18
| | | | | | | | | The gateway code is now adapted in order to correctly interact with the Translation Table component by using the vlan ID Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: print the VID together with the TT entriesAntonio Quartulli2013-10-192-32/+52
| | | | | Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: use vid when computing local and global TT CRCAntonio Quartulli2013-10-191-4/+31
| | | | | | | | | | now that each TT entry is characterised by a VLAN ID, the latter has to be taken into consideration when computing the local/global table CRC as it would be theoretically possible to have the same client in two different VLANs Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: add the VLAN ID attribute to the TT entryAntonio Quartulli2013-10-1913-135/+312
| | | | | | | | | To make the translation table code VLAN-aware, each entry must carry the VLAN ID which it belongs to. This patch adds such attribute to the related TT structures. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: update email address for Marek LindnerMarek Lindner2013-10-191-1/+1
| | | | | Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: update email address for Simon WunderlichSimon Wunderlich2013-10-191-1/+1
| | | | | | | | My university will stop email service for alumni in january 2014, please use my new e-mail address instead. Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
* batman-adv: check skb preparation return valueAntonio Quartulli2013-10-191-3/+6
| | | | | | | Fix bogus merge conflict resolution by checking the return values of the skb preparation routines. Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: Add dummy soft-interface rx mode handlerLinus Lüssing2013-10-121-0/+13
| | | | | | | | | | We do not actually need to set any rx filters for the virtual batman soft interface. However a dummy handler enables a user to set static multicast listeners for instance. Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: make batadv_tt_save_orig_buffer() genericAntonio Quartulli2013-10-121-6/+4
| | | | | | | | This is a simple batadv_tt_save_orig_buffer() refactoring aiming to make it more generic and avoid useless casts. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: implement batadv_tt_entriesAntonio Quartulli2013-10-121-4/+15
| | | | | | | | | | Implement batadv_tt_entries() to get the number of entries fitting in a given amount of bytes. This computation is done several times in the code and therefore it is useful to have an helper function. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: remove useless find_router look upSimon Wunderlich2013-10-121-21/+8
| | | | | | | | | | This is not used anymore with the new fragmentation, and it might actually mess up the bonding code because find_router() assumes it is only called once per packet. Signed-off-by: Simon Wunderlich <simon@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: consider network coding overhead when calculating required mtuMarek Lindner2013-10-125-17/+37
| | | | | | | | | | | The module prints a warning when the MTU on the hard interface is too small to transfer payload traffic without fragmentation. The required MTU is calculated based on the encapsulation header size. If network coding is compild into the module its header size is taken into account as well. Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: create common header for ICMP packetsAntonio Quartulli2013-10-124-42/+62
| | | | | | | | | | | | | | | | | | | | the icmp and the icmp_rr packets share the same initial fields since they use the same code to be processed and forwarded. Extract the common fields and put them into a separate struct so that future ICMP packets can be easily added without bloating the packet definition. However, keep the seqno field outside of the newly created common header because future ICMP types may require a bigger sequence number space. This change breaks compatibility due to fields reordering in the ICMP headers. Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
* batman-adv: use htons when possibleAntonio Quartulli2013-10-125-13/+13
| | | | | | | | | | | | | | | | | When comparing a network ordered value with a constant, it is better to convert the constant at compile time by means of htons() instead of converting the value at runtime using ntohs(). This refactoring may slightly improve the code performance. Moreover substitute __constant_htons() with htons() since the latter increase readability and it is smart enough to be as efficient as the former Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
* batman-adv: Fragment and send skbs larger than mtuMartin Hundebøll2013-10-125-4/+154
| | | | | | | | | | | Non-broadcast packets larger than MTU are fragmented and sent with an encapsulating header. Up to 16 fragments are supported, which are sent in reverse order on the wire to allow minimal memory copying when creating fragments. Signed-off-by: Martin Hundebøll <martin@hundeboll.net> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
* batman-adv: Receive fragmented packets and mergeMartin Hundebøll2013-10-1211-1/+574
| | | | | | | | | | | | | Fragments arriving at their destination are buffered for later merge. Merged packets are passed to the main receive function as had they never been fragmented. Fragments are forwarded without merging if the MTU of the outgoing interface is smaller than the size of the merged packet. Signed-off-by: Martin Hundebøll <martin@hundeboll.net> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
OpenPOWER on IntegriCloud