summaryrefslogtreecommitdiffstats
path: root/include/linux/regulator
Commit message (Collapse)AuthorAgeFilesLines
* regulator: Add option for machine drivers to enable the dummy regulatorMark Brown2010-10-281-0/+5
| | | | | | | | | | | | | Allow machine drivers to explicitly enable the use of the dummy regulator, enabling simpler support for systems with only a few specific supplies visible to software. It is strongly recommended that this is not used on systems with substantial software control over their PMICs, for maximum functionality constrints should be as fully specified as possible. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* Regulator: LP3972 PMIC regulator driverAxel Lin2010-10-281-0/+48
| | | | | | | | | | This patch adds regulator drivers for National Semiconductors LP3972 PMIC. This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out (LDO) regulators. LP3972 PMIC controller uses I2C interface. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* MAX8952 PMIC Driver Initial ReleaseMyungJoo Ham2010-10-281-0/+135
| | | | | | | | | | | | | | | | | | | | | | | | | | MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV with DVS support. In this initial release, users can set voltages for four DVS modes, RAMP delay values, and SYNC frequency. Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID is not supported in this release. If GPIO of EN is not valid in platform data, the driver assumes that it is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down VID0 and VID1 to fix DVS mode as 0 and disables DVS support. We assume that V_OUT is capable to provide every voltage from 770mV to 1.40V in 10mV steps although the data sheet has some ambiguity on it. Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> -- v2: - Style correction - Can accept platform_data with invalid GPIOs - Removed unnecessary features - Improved error handling Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* ab8500-mfd: add regulator support to ab8500 mfd deviceSundar R Iyer2010-08-111-0/+25
| | | | | | | | | | Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-By: Mattias Wallin <mattias.wallin@stericsson.com> Acked-By: Bengt JONSSON <bengt.g.jonsson@stericsson.com> Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH registerAnuj Aggarwal2010-07-281-0/+32
| | | | | | | | | | | | | | | | | | | | Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> In TPS6507x, depending on the status of DEFDCDC{2,3} pin either DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or programmed to change the output voltage. The current driver assumes DEFDCDC{2,3} pins are always tied low and thus operates only on DEFDCDC{2,3}_LOW register. This need not always be the case (as is found on OMAP-L138 EVM). Unfortunately, software cannot read the status of DEFDCDC{2,3} pins. So, this information is passed through platform data depending on how the board is wired. Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Allow regulator-regulator supplies to be specified by nameMark Brown2010-05-251-2/+7
| | | | | | | | | | | | | When one regulator supplies another allow the relationship to be specified using names rather than struct regulators, in a similar manner to that allowed for consumer supplies. This allows static configuration at compile time, reducing the need for dynamic init code. Also change the references to LINE supply to be system supply since line is sometimes used for actual supplies and therefore potentially confusing. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Let drivers know when they use the stub APIJean Delvare2010-04-191-2/+6
| | | | | | | | | | | Have the stub variant of regulator_get() return NULL, so that drivers can (but still don't have to) handle this case specifically. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Jerome Oufella <jerome.oufella@savoirfairelinux.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: enable max8649 regulator driverHaojian Zhuang2010-03-031-0/+44
| | | | | | Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Add 'start-up time' to fixed voltage regulatorsAdrian Hunter2010-03-031-0/+2
| | | | | | | | | Add a field to specify a delay for the start-up time of a fixed voltage regulator. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Allow regulators to specify the time taken to ramp on enableMark Brown2010-03-031-0/+6
| | | | | | | | | | | | | | | | | Regulators may sometimes take longer to enable than the control operation used to do so, either because the regulator has ramp rate control used to limit inrush current or because the control operation is very fast (GPIO being the most common example of this). In order to ensure that consumers do not rely on the regulator before it is enabled provide an enable_time() operation and have the core delay for that time before returning to the caller. This is implemented as a function since the ramp rate may be specified in voltage per unit time and therefore the time depend on the configuration. In future it would be desirable to allow the bulk operations to run the delays for multiple enables in parallel but this is not currently supported. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: Add notifier event on regulator disableMark Brown2010-03-031-1/+3
| | | | | | | | | | | The intended use case is for drivers which disable regulators to save power but need to do some work to restore the hardware state when restarting. If the supplies are not actually disabled due to board limits or sharing with other active devices this notifier allows the driver to avoid unneeded reinitialisation, particularly when used with runtime PM. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: consumer.h - fix build when consumer.h is #included first.Liam Girdwood2009-12-171-0/+2
| | | | | | consumer.h requires device.h for stand alone build. Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Handle regulators without suspend mode configurationMark Brown2009-12-171-1/+5
| | | | | | | | | | | | | | | | | Since some regulators in the system may not support suspend mode configuration we need to allow some regulators to have a missing suspend mode configuration. Do this by requiring that disabled regulators are explicitly flagged and then skip over regulators that have no state specified. Try to avoid surprises by warning the if we could set the state but no configuration is provided. This also ensures that an all zeros configuration generates a warning rather than silently disabling the regulator. Reported-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: add driver for MAX8660/8661Wolfram Sang2009-12-171-0/+57
| | | | | | | | Tested with a MX25-based custom board. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator/driver: be more specific in nanodoc for is_enabledWolfram Sang2009-09-221-1/+2
| | | | | | | | | Document the possibility that is_enabled may also return with negative errorcodes. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: fix typosWolfram Sang2009-09-222-5/+5
| | | | | | | | Fix a couple of typos I found while working with this subsystem. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Add GPIO enable control to fixed voltage regulator driverRoger Quadros2009-09-221-0/+24
| | | | | | | | | | | | | Now fixed regulators that have their enable pin connected to a GPIO line can use the fixed regulator driver for regulator enable/disable control. The GPIO number and polarity information is passed through platform data. GPIO enable control is achieved using gpiolib. Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com> Reviewed-by: Philipp Zabel <philipp.zabel@gmail.com> Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Add regulator voltage range check APIMark Brown2009-09-221-0/+2
| | | | | | | | Simplify checking of support for voltage ranges by providing an API which wraps the existing count and list operations. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Add regulator_get_exclusive() APIMark Brown2009-09-222-0/+4
| | | | | | | | | | | | | | | | | | | | | Some consumers require complete control of the regulator and can't tolerate sharing it with other consumers, most commonly because they need to have the regulator actually disabled so can't have other consumers forcing it on. This new regulator_get_exclusive() API call allows these consumers to explicitly request this, documenting the assumptions that they are making. In order to simplify coding of such consumers the use count for regulators they request is forced to match the enabled state of the regulator when it is requested. This is not possible for consumers which can share regulators due to the need to keep track of the ownership of use counts. A new API call is used rather than an additional argument to the existing regulator_get() in order to avoid merge headaches with driver code in other trees. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: add initialization macro of regulator supplyroald2009-09-221-0/+7
| | | | | | Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Define full constraints function with REGULATOR disabledMark Brown2009-09-221-0/+6
| | | | | | | | | This allows machine drivers to build without ifdefs if they have full constraints. Suggested by machine drivers contributed by Haojian Zhuang <haojian.zhuang@gmail.com>. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Allow consumer supplies to be set up with dev_name()Mark Brown2009-09-221-1/+6
| | | | | | | | | | | | | | | | | Follow the approach suggested by Russell King and implemented by him in the clkdev API and allow consumer device supply mapings to be set up using the dev_name() for the consumer instead of the struct device. In order to avoid making existing machines instabuggy and creating merge issues the use of struct device is still supported for the time being. This resolves problems working with buses such as I2C which make the struct device available late providing that the final device name is known, which is the case for most embedded systems with fixed setups. Consumers must still use the struct device when calling regulator_get(). Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Provide mode to status conversion functionMark Brown2009-09-171-0/+2
| | | | | | | This is useful for implementing get_status() in terms of get_mode(). Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* regulator/max1586: support increased V3 voltage rangePhilipp Zabel2009-06-151-0/+11
| | | | | | | | | | | | | | The V3 regulator can be configured with an external resistor connected to the feedback pin (R24 in the data sheet) to increase the voltage range. For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* LP3971 PMIC regulator driver (updated and combined version)Marek Szyprowski2009-06-151-0/+51
| | | | | | | | | | | This patch adds regulator drivers for National Semiconductors LP3971 PMIC. This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface. Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: add userspace-consumer driverMike Rapoport2009-06-151-0/+25
| | | | | | | | | | | The userspace-consumer driver allows control of voltage and current regulator state from userspace. This is required for fine-grained power management of devices that are completely controller by userspace applications, e.g. a GPS transciever connected to a serial port. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* Maxim 1586 regulator driverRobert Jarzmik2009-06-151-0/+52
| | | | | | | | | | | | | | The Maxim 1586 regulator is a voltage regulator with 2 voltage outputs, specially suitable for Marvell PXA chips. One output is in the range of required VCC_CORE by the PXA27x chips, the other in the VCC_USIM required as well by PXA27x chips. The chip is controlled through the I2C bus. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: fix header file missing kernel-docRandy Dunlap2009-04-281-0/+1
| | | | | | | | | | | Add regulator header file missing kernel-doc: Warning(include/linux/regulator/driver.h:117): No description found for parameter 'set_mode' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> cc: Liam Girdwood <lrg@slimlogic.co.uk> cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Support disabling of unused regulators by machinesMark Brown2009-03-311-0/+2
| | | | | | | | | | | | | | | | At present it is not possible for machine constraints to disable regulators which have been left on when the system starts, for example as a result of fixed default configurations in hardware. This means that power may be wasted by these regulators if they are not in use. Provide intial support for this with a late_initcall which will disable any unused regulators if the machine has enabled this feature by calling regulator_has_full_constraints(). If this has not been called then print a warning to encourage users to fully specify their constraints so that we can change this to be the default behaviour in future. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Allow boot_on regulators to be disabled by clientsMark Brown2009-03-311-1/+3
| | | | | | | | | | Rather than incrementing the reference count for boot_on regulators (which prevents them being disabled later on) simply force the regulator to be enabled when applying the constraints. Previously boot_on was essentially equivalent to always_on. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: get_status() grows kerneldocDavid Brownell2009-03-311-9/+10
| | | | | | | | | | | | | | | Add kerneldoc for the new get_status() message. Fix the existing kerneldoc for that struct in two ways: (a) Syntax, making sure parameter descriptions immediately follow the one-line struct description and that the first blank lines is before any more expansive description; (b) Presentation for a few points, to highlight the fact that the previous "get" methods exist only to report the current configuration, not to display actual status. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: enumerate voltages (v2)David Brownell2009-03-312-0/+11
| | | | | | | | | | | | | | | | | | | Add a basic mechanism for regulators to report the discrete voltages they support: list_voltage() enumerates them using selectors numbered from 0 to an upper bound. Use those methods to force machine-level constraints into bounds. (Example: regulator supports 1.8V, 2.4V, 2.6V, 3.3V, and board constraints for that rail are 2.0V to 3.6V ... so the range of voltages is then 2.4V to 3.3V on this board.) Export those voltages to the regulator consumer interface, so for example regulator hooked up to an MMC/SD/SDIO slot can report the actual voltage options available to cards connected there. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Allow regulators to set the initial operating modeMark Brown2009-03-311-0/+4
| | | | | | | | This is useful when wishing to run in a fixed operating mode that isn't the default. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: email - update email address and regulator webpage.Liam Girdwood2009-03-313-3/+3
| | | | | | | Remove deceased email address and update to new address. Also update website details in MAINTAINERS with correct page. Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: fix header file missing kernel-docRandy Dunlap2009-03-311-0/+1
| | | | | | | | | | | Fix regulator/driver.h missing kernel-doc: Warning(linux-next-20090120//include/linux/regulator/driver.h:108): No description found for parameter 'get_status' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> cc: Liam Girdwood <lrg@slimlogic.co.uk> cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Hoist struct regulator_dev out of core to fix notifiersMark Brown2009-03-311-0/+32
| | | | | | | | | Commit 872ed3fe176833f7d43748eb88010da4bbd2f983 caused regulator drivers to take the struct regulator_dev lock themselves which requires that the struct be visible to them. Band aid this by making the struct visible. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Allow init_data to be passed to fixed voltage regulatorsMark Brown2009-03-311-0/+3
| | | | | Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Allow init data to be supplied for bq24022Mark Brown2009-03-311-0/+3
| | | | | | | | Previously it was not possible to do so, making it impossible for machines to configure the driver. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Pass regulator init data as explict argument when registeringMark Brown2009-03-311-1/+2
| | | | | | | | | | | Rather than having the regulator init data read from the platform_data member of the struct device that is registered for the regulator make the init data an explict argument passed in when registering. This allows drivers to use the platform data for their own purposes if they wish. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* Regulator: Push lock out of _notifier_call_chain + add voltage change event.Jonathan Cameron2009-03-311-0/+2
| | | | | | | | Regulator: Push lock out of _notifier_call_chain and into caller functions (side effect of fixing deadlock in regulator_force_disable) + Add a voltage changed event. Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: add get_status()David Brownell2009-03-311-0/+17
| | | | | | | | | | | | | | | | | | | | | Based on previous LKML discussions: * Update docs for regulator sysfs class attributes to highlight the fact that all current attributes are intended to be control inputs, including notably "state" and "opmode" which previously implied otherwise. * Define a new regulator driver get_status() method, which is the first method reporting regulator outputs instead of inputs. It can report on/off and error status; or instead of simply "on", report the actual operating mode. For the moment, this is a sysfs-only interface, not accessible to regulator clients. Such clients can use the current notification interfaces to detect errors, if the regulator reports them. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: fix kernel-doc warningsRandy Dunlap2009-01-081-5/+2
| | | | | | | | | | | | | Fix kernel-doc warnings in regulator/driver.h: Warning(linux-next-20090108//include/linux/regulator/driver.h:95): Excess struct/union/enum/typedef member 'set_current' description in 'regulator_ops' Warning(linux-next-20090108//include/linux/regulator/driver.h:95): Excess struct/union/enum/typedef member 'get_current' description in 'regulator_ops' Warning(linux-next-20090108//include/linux/regulator/driver.h:124): No description found for parameter 'irq' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> cc: Liam Girdwood <lrg@slimlogic.co.uk> cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Add missing kerneldocMark Brown2009-01-082-1/+80
| | | | | | | This is only the documentation that the kerneldoc system warns about. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Clean up kerneldoc warningsMark Brown2009-01-081-4/+4
| | | | | | | | | Remove kerneldoc warnings that don't relate to missing documentation, mostly by renaming parameters in the documentation to match their actual names. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: Fix typoMark Brown2008-10-131-1/+1
| | | | | Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: core - Rework machine API to remove string based functions.Liam Girdwood2008-10-132-9/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This improves the machine level API in order to configure regulator constraints and consumers as platform data and removes the old string based API that required several calls to set up each regulator. The intention is to create a struct regulator_init_data, populate it's fields with constraints, consumers devices, etc and then register the regulator device from board.c in the standard Linux way. e.g. regulator LDO2 (supplying codec and sim) platform data. /* regulator LDO2 consumer devices */ static struct regulator_consumer_supply ldo2_consumers[] = { { .dev = &platform_audio_device.dev, .supply = "codec_avdd", }, { .dev = &platform_sim_device.dev, .supply = "sim_vcc", } }; /* regulator LDO2 constraints */ static struct regulator_init_data ldo2_data = { .constraints = { .min_uV = 3300000, .max_uV = 3300000, .valid_modes_mask = REGULATOR_MODE_NORMAL, .apply_uV = 1, }, .num_consumer_supplies = ARRAY_SIZE(ldo2_consumers), .consumer_supplies = ldo2_consumers, }; /* machine regulator devices with thier consumers and constraints */ static struct platform_device wm8350_regulator_devices[] = { { .name = "wm8350-regulator", .id = WM8350_LDO_2, .dev = { .platform_data = &ldo2_data, }, }, }; Changes in detail:- o Removed all const char* regulator config functions in machine API. o Created new struct regulator_init_data to contain regulator machine configuration constraints and consmuers. o Changed set_supply(), set_machine_constraints(), set_consumer_device_supply() to remove their string identifier parameters. Also made them static and moved functions nearer top of core.c. o Removed no longer used inline func to_rdev() o Added regulator_get_init_drvdata() to retrieve init data. o Added struct device* as parameter to regulator_register(). o Changed my email address. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* regulator: TI bq24022 Li-Ion Charger driverPhilipp Zabel2008-07-301-0/+21
| | | | | | | | This adds a regulator driver for the TI bq24022 Single-Chip Li-Ion Charger with its nCE and ISET2 pins connected to GPIOs. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
* regulator: fixed regulator interfaceMark Brown2008-07-301-0/+22
| | | | | | | | | This patch adds support for fixed regulators. This class of regulator is not software controllable but can coexist on machines with software controlable regulators. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
* regulator: machine driver interfaceLiam Girdwood2008-07-301-0/+104
| | | | | | | | | | | | | This interface is for machine specific code and allows the creation of voltage/current domains (with constraints) for each regulator. It can provide regulator constraints that will prevent device damage through overvoltage or over current caused by buggy client drivers. It also allows the creation of a regulator tree whereby some regulators are supplied by others (similar to a clock tree). Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com> Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* regulator: regulator driver interfaceLiam Girdwood2008-07-301-0/+99
| | | | | | | | | This allows regulator drivers to register their regulators and provide operations to the core. It also has a notifier call chain for propagating regulator events to clients. Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
OpenPOWER on IntegriCloud