summaryrefslogtreecommitdiffstats
path: root/include/linux/msi.h
Commit message (Collapse)AuthorAgeFilesLines
* genirq/msi: Allow level-triggered MSIs to be exposed by MSI providersMarc Zyngier2018-05-131-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So far, MSIs have been used to signal edge-triggered interrupts, as a write is a good model for an edge (you can't "unwrite" something). On the other hand, routing zillions of wires in an SoC because you need level interrupts is a bit extreme. People have come up with a variety of schemes to support this, which involves sending two messages: one to signal the interrupt, and one to clear it. Since the kernel cannot represent this, we've ended up with side-band mechanisms that are pretty awful. Instead, let's acknoledge the requirement, and ensure that, under the right circumstances, the irq_compose_msg and irq_write_msg can take as a parameter an array of two messages instead of a pointer to a single one. We also add some checking that the compose method only clobbers the second message if the MSI domain has been created with the MSI_FLAG_LEVEL_CAPABLE flags. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Rob Herring <robh@kernel.org> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lkml.kernel.org/r/20180508121438.11301-2-marc.zyngier@arm.com
* Merge branch 'irq-core-for-linus' of ↵Linus Torvalds2017-11-131-0/+5
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq core updates from Thomas Gleixner: "A rather large update for the interrupt core code and the irq chip drivers: - Add a new bitmap matrix allocator and supporting changes, which is used to replace the x86 vector allocator which comes with separate pull request. This allows to replace the convoluted nested loop allocation function in x86 with a facility which supports the recently added property of managed interrupts proper and allows to switch to a best effort vector reservation scheme, which addresses problems with vector exhaustion. - A large update to the ARM GIC-V3-ITS driver adding support for range selectors. - New interrupt controllers: - Meson and Meson8 GPIO - BCM7271 L2 - Socionext EXIU If you expected that this will stop at some point, I have to disappoint you. There are new ones posted already. Sigh! - STM32 interrupt controller support for new platforms. - A pile of fixes, cleanups and updates to the MIPS GIC driver - The usual small fixes, cleanups and updates all over the place. Most visible one is to move the irq chip drivers Kconfig switches into a separate Kconfig menu" * 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits) genirq: Fix type of shifting literal 1 in __setup_irq() irqdomain: Drop pointless NULL check in virq_debug_show_one genirq/proc: Return proper error code when irq_set_affinity() fails irq/work: Use llist_for_each_entry_safe irqchip: mips-gic: Print warning if inherited GIC base is used irqchip/mips-gic: Add pr_fmt and reword pr_* messages irqchip/stm32: Move the wakeup on interrupt mask irqchip/stm32: Fix initial values irqchip/stm32: Add stm32h7 support dt-bindings/interrupt-controllers: Add compatible string for stm32h7 irqchip/stm32: Add multi-bank management irqchip/stm32: Select GENERIC_IRQ_CHIP irqchip/exiu: Add support for Socionext Synquacer EXIU controller dt-bindings: Add description of Socionext EXIU interrupt controller irqchip/gic-v3-its: Fix VPE activate callback return value irqchip: mips-gic: Make IPI bitmaps static irqchip: mips-gic: Share register writes in gic_set_type() irqchip: mips-gic: Remove gic_vpes variable irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs irqchip: mips-gic: Configure EIC when CPUs come online ...
| * genirq/irqdomain: Add force reactivation flag to irq domainsThomas Gleixner2017-09-251-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Allow irqdomains to tell the core code, that after early activation the interrupt needs to be reactivated at request_irq() time. This allows reservation of vectors at early activation time and actual vector assignment at request_irq() time. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Juergen Gross <jgross@suse.com> Tested-by: Yu Chen <yu.c.chen@intel.com> Acked-by: Juergen Gross <jgross@suse.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Alok Kataria <akataria@vmware.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Rui Zhang <rui.zhang@intel.com> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Len Brown <lenb@kernel.org> Link: https://lkml.kernel.org/r/20170913213153.106242536@linutronix.de
* | License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman2017-11-021-0/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* staging: fsl-mc: add missing fsl_mc comment in struct msi_descLaurentiu Tudor2017-07-301-0/+1
| | | | | | | | | The mc-bus specific field, fsl_mc in struct msi_desc is missing its comment so add it. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge tag 'pci-v4.11-changes' of ↵Linus Torvalds2017-02-231-6/+0
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: - add ASPM L1 substate support - enable PCIe Extended Tags when supported - configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx - increase VPD access timeout - add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432 - use new pci_irq_alloc_vectors() in more drivers - fix MSI affinity memory leak - remove unused MSI interfaces and update documentation - remove unused AER .link_reset() callback - avoid pci_lock / p->pi_lock deadlock seen with perf - serialize sysfs enable/disable num_vfs operations - move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and refactor so we can support both hosts and endpoints - add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers - add Rockchip system power management support - add Thunder-X cn81xx and cn83xx support - add Exynos 5440 PCIe PHY support * tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits) PCI: dwc: Remove dependency of designware on CONFIG_PCI PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host PCI: dwc: Split pcie-designware.c into host and core files PCI: dwc: designware: Fix style errors in pcie-designware.c PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc() PCI: dwc: all: Split struct pcie_port into host-only and core structures PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init() PCI: dwc: all: Rename cfg_read/cfg_write to read/write PCI: dwc: all: Use platform_set_drvdata() to save private data PCI: dwc: designware: Move register defines to designware header file PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code PCI: dra7xx: Group PHY API invocations PCI: dra7xx: Enable MSI and legacy interrupts simultaneously PCI: dra7xx: Add support to force RC to work in GEN1 mode PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional() PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory PCI: exynos: Support the PHY generic framework Documentation: binding: Modify the exynos5440 PCIe binding phy: phy-exynos-pcie: Add support for Exynos PCIe PHY Documentation: samsung-phy: Add exynos-pcie-phy binding ...
| * PCI/MSI: Remove pci_msi_domain_{alloc,free}_irqs()Christoph Hellwig2017-02-101-3/+0
| | | | | | | | | | | | | | | | Just call the msi_* version directly instead of having trivial wrappers for one or two callsites. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
| * PCI/MSI: Remove unused pci_msi_create_default_irq_domain()Christoph Hellwig2017-02-101-3/+0
| | | | | | | | | | | | | | | | pci_msi_create_default_irq_domain() is never called in the whole tree, so remove it as well as all the supporting code for a default PCI MSI domain. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
* | genirq/msi: Add stubs for get_cached_msi_msg/pci_write_msi_msgArnd Bergmann2017-02-161-1/+10
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A bug fix to the MSIx handling in vfio added references to functions that may not be defined if MSI is disabled in the kernel, resulting in this link error: drivers/built-in.o: In function `vfio_msi_set_vector_signal': :(.text+0x450808): undefined reference to `get_cached_msi_msg' :(.text+0x45080c): undefined reference to `write_msi_msg' As suggested by Alex Williamson, add stub implementations for get_cached_msi_msg() and pci_write_msi_msg(). In case this bugfix gets backported, please note that the #ifdef has changed over time, originally both functions were implemented in drivers/pci/msi.c and controlled by CONFIG_PCI_MSI, while nowadays get_cached_msi_msg() is part of the generic MSI support and can be used without PCI. Fixes: b8f02af096b1 ("vfio/pci: Restore MSIx message prior to enabling") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Bart Van Assche <bart.vanassche@sandisk.com> Link: http://lkml.kernel.org/r/1413190208.4202.34.camel@ul30vt.home Link: http://lkml.kernel.org/r/20170214215343.3307861-1-arnd@arndb.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* genirq/msi: Add cpumask allocation to alloc_msi_entryThomas Gleixner2016-09-141-2/+3
| | | | | | | | | | | | | | | | | | | | | For irq spreading want to store affinity masks in the msi_entry. Add the infrastructure for it. We allocate an array of cpumasks with an array size of the number of used vectors in the entry, so we can hand in the information per linux interrupt later. As we hand in the number of used vectors, we assign them right away. Convert all the call sites. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: axboe@fb.com Cc: keith.busch@intel.com Cc: agordeev@redhat.com Cc: linux-block@vger.kernel.org Cc: Christoph Hellwig <hch@lst.de> Link: http://lkml.kernel.org/r/1473862739-15032-2-git-send-email-hch@lst.de
* genirq/msi: Make sure PCI MSIs are activated earlyMarc Zyngier2016-08-091-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Bharat Kumar Gogada reported issues with the generic MSI code, where the end-point ended up with garbage in its MSI configuration (both for the vector and the message). It turns out that the two MSI paths in the kernel are doing slightly different things: generic MSI: disable MSI -> allocate MSI -> enable MSI -> setup EP PCI MSI: disable MSI -> allocate MSI -> setup EP -> enable MSI And it turns out that end-points are allowed to latch the content of the MSI configuration registers as soon as MSIs are enabled. In Bharat's case, the end-point ends up using whatever was there already, which is not what you want. In order to make things converge, we introduce a new MSI domain flag (MSI_FLAG_ACTIVATE_EARLY) that is unconditionally set for PCI/MSI. When set, this flag forces the programming of the end-point as soon as the MSIs are allocated. A consequence of this is that we have an extra activate in irq_startup, but that should be without much consequence. tglx: - Several people reported a VMWare regression with PCI/MSI-X passthrough. It turns out that the patch also cures that issue. - We need to have a look at the MSI disable interrupt path, where we write the msg to all zeros without disabling MSI in the PCI device. Is that correct? Fixes: 52f518a3a7c2 "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts" Reported-and-tested-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com> Reported-and-tested-by: Foster Snowhill <forst@forstwoof.ru> Reported-by: Matthias Prager <linux@matthiasprager.de> Reported-by: Jason Taylor <jason.taylor@simplivity.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: linux-pci@vger.kernel.org Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1468426713-31431-1-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* genirq/msi: Make use of affinity aware allocationsThomas Gleixner2016-07-041-0/+2
| | | | | | | | | | | | | | | Allow the MSI code to provide affinity hints per MSI descriptor. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Christoph Hellwig <hch@lst.de> Cc: linux-block@vger.kernel.org Cc: linux-pci@vger.kernel.org Cc: linux-nvme@lists.infradead.org Cc: axboe@fb.com Cc: agordeev@redhat.com Link: http://lkml.kernel.org/r/1467621574-8277-6-git-send-email-hch@lst.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* genirq/msi: Remove unused MSI_FLAG_IDENTITY_MAPThomas Gleixner2016-07-041-4/+2
| | | | | | | | | | | | | | | | No user and we definitely don't want to grow one. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Christoph Hellwig <hch@lst.de> Cc: linux-block@vger.kernel.org Cc: linux-pci@vger.kernel.org Cc: linux-nvme@lists.infradead.org Cc: axboe@fb.com Cc: agordeev@redhat.com Link: http://lkml.kernel.org/r/1467621574-8277-2-git-send-email-hch@lst.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* fsl-mc: msi: Added FSL-MC-specific member to the msi_desc's unionJ. German Rivera2016-02-071-0/+9
| | | | | | | | FSL-MC is a bus type different from PCI and platform, so it needs its own member in the msi_desc's union. Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge tag 'pci-v4.5-changes' of ↵Linus Torvalds2016-01-211-2/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "PCI changes for the v4.5 merge window: Enumeration: - Simplify config space size computation (Bjorn Helgaas) - Avoid iterating through ROM outside the resource window (Edward O'Callaghan) - Support PCIe devices with short cfg_size (Jason S. McMullan) - Add Netronome vendor and device IDs (Jason S. McMullan) - Limit config space size for Netronome NFP6000 family (Jason S. McMullan) - Add Netronome NFP4000 PF device ID (Simon Horman) - Limit config space size for Netronome NFP4000 (Simon Horman) - Print warnings for all invalid expansion ROM headers (Vladis Dronov) Resource management: - Fix minimum allocation address overwrite (Christoph Biedl) PCI device hotplug: - acpiphp_ibm: Fix null dereferences on null ibm_slot (Colin Ian King) - pciehp: Always protect pciehp_disable_slot() with hotplug mutex (Guenter Roeck) - shpchp: Constify hpc_ops structure (Julia Lawall) - ibmphp: Remove unneeded NULL test (Julia Lawall) Power management: - Make ASPM sysfs link_state_store() consistent with link_state_show() (Andy Lutomirski) Virtualization - Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183 (Tim Sander) MSI: - Remove empty pci_msi_init_pci_dev() (Bjorn Helgaas) - Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREAD (Grygorii Strashko) - Initialize MSI capability for all architectures (Guilherme G. Piccoli) - Relax msi_domain_alloc() to support parentless MSI irqdomains (Liu Jiang) ARM Versatile host bridge driver: - Remove unused pci_sys_data structures (Lorenzo Pieralisi) Broadcom iProc host bridge driver: - Hide CONFIG_PCIE_IPROC (Arnd Bergmann) - Do not use 0x in front of %pap (Dmitry V. Krivenok) - Update iProc PCIe device tree binding (Ray Jui) - Add PAXC interface support (Ray Jui) - Add iProc PCIe MSI device tree binding (Ray Jui) - Add iProc PCIe MSI support (Ray Jui) Freescale i.MX6 host bridge driver: - Use gpio_set_value_cansleep() (Fabio Estevam) - Add support for active-low reset GPIO (Petr Štetiar) HiSilicon host bridge driver: - Add support for HiSilicon Hip06 PCIe host controllers (Gabriele Paoloni) Intel VMD host bridge driver: - Export irq_domain_set_info() for module use (Keith Busch) - x86/PCI: Allow DMA ops specific to a PCI domain (Keith Busch) - Use 32 bit PCI domain numbers (Keith Busch) - Add driver for Intel Volume Management Device (VMD) (Keith Busch) Qualcomm host bridge driver: - Document PCIe devicetree bindings (Stanimir Varbanov) - Add Qualcomm PCIe controller driver (Stanimir Varbanov) - dts: apq8064: add PCIe devicetree node (Stanimir Varbanov) - dts: ifc6410: enable PCIe DT node for this board (Stanimir Varbanov) Renesas R-Car host bridge driver: - Add support for R-Car H3 to pcie-rcar (Harunobu Kurokawa) - Allow DT to override default window settings (Phil Edworthy) - Convert to DT resource parsing API (Phil Edworthy) - Revert "PCI: rcar: Build pcie-rcar.c only on ARM" (Phil Edworthy) - Remove unused pci_sys_data struct from pcie-rcar (Phil Edworthy) - Add runtime PM support to pcie-rcar (Phil Edworthy) - Add Gen2 PHY setup to pcie-rcar (Phil Edworthy) - Add gen2 fallback compatibility string for pci-rcar-gen2 (Simon Horman) - Add gen2 fallback compatibility string for pcie-rcar (Simon Horman) Synopsys DesignWare host bridge driver: - Simplify control flow (Bjorn Helgaas) - Make config accessor override checking symmetric (Bjorn Helgaas) - Ensure ATU is enabled before IO/conf space accesses (Stanimir Varbanov) Miscellaneous: - Add of_pci_get_host_bridge_resources() stub (Arnd Bergmann) - Check for PCI_HEADER_TYPE_BRIDGE equality, not bitmask (Bjorn Helgaas) - Fix all whitespace issues (Bogicevic Sasa) - x86/PCI: Simplify pci_bios_{read,write} (Geliang Tang) - Use to_pci_dev() instead of open-coding it (Geliang Tang) - Use kobj_to_dev() instead of open-coding it (Geliang Tang) - Use list_for_each_entry() to simplify code (Geliang Tang) - Fix typos in <linux/msi.h> (Thomas Petazzoni) - x86/PCI: Clarify AMD Fam10h config access restrictions comment (Tomasz Nowicki)" * tag 'pci-v4.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (58 commits) PCI: Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183 PCI: Limit config space size for Netronome NFP4000 PCI: Add Netronome NFP4000 PF device ID x86/PCI: Add driver for Intel Volume Management Device (VMD) PCI/AER: Use 32 bit PCI domain numbers x86/PCI: Allow DMA ops specific to a PCI domain irqdomain: Export irq_domain_set_info() for module use PCI: host: Add of_pci_get_host_bridge_resources() stub genirq/MSI: Relax msi_domain_alloc() to support parentless MSI irqdomains PCI: rcar: Add Gen2 PHY setup to pcie-rcar PCI: rcar: Add runtime PM support to pcie-rcar PCI: designware: Make config accessor override checking symmetric PCI: ibmphp: Remove unneeded NULL test ARM: dts: ifc6410: enable PCIe DT node for this board ARM: dts: apq8064: add PCIe devicetree node PCI: hotplug: Use list_for_each_entry() to simplify code PCI: rcar: Remove unused pci_sys_data struct from pcie-rcar PCI: hisi: Add support for HiSilicon Hip06 PCIe host controllers PCI: Avoid iterating through memory outside the resource window PCI: acpiphp_ibm: Fix null dereferences on null ibm_slot ...
| * PCI/MSI: Fix typos in <linux/msi.h>Thomas Petazzoni2016-01-071-2/+2
| | | | | | | | | | | | Fix two comment typos in the <linux/msi.h> header. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* | platform-msi: Allow creation of a MSI-based stacked irq domainMarc Zyngier2015-12-161-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We almost have all the needed bits requiredable to create a irq domain on top of a MSI domain. For this, we enable a few things: - the virq is stored in the msi_desc - device, msi_alloc_info and domain-specific data are stored in the platform_priv_data structure - we introduce a new API for platform-msi: /* Create a MSI-based domain */ struct irq_domain * platform_msi_create_device_domain(struct device *dev, unsigned int nvec, irq_write_msi_msg_t write_msi_msg, const struct irq_domain_ops *ops, void *host_data); /* Allocate MSIs in an MSI domain */ int platform_msi_domain_alloc(struct irq_domain *domain, unsigned int virq, unsigned int nr_irqs); /* Free MSIs from an MSI domain */ void platform_msi_domain_free(struct irq_domain *domain, unsigned int virq, unsigned int nvec); /* Obtain the host data passed to platform_msi_create_device_domain */ void *platform_msi_get_host_data(struct irq_domain *domain); platform_msi_create_device_domain() is a hybrid of irqdomain creation and interrupt allocation, creating a domain backed by the MSIs associated to a device. IRQs can then be allocated in that domain using platform_msi_domain_alloc(). This now allows a wired irq to MSI bridge to be created. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* | genirq/msi: Add msi_domain_populate_irqsMarc Zyngier2015-12-161-0/+2
| | | | | | | | | | | | | | To be able to allocate interrupts from the MSI layer down, add a new msi_domain_populate_irqs entry point. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* | genirq/msi: Make the .prepare callback reusableMarc Zyngier2015-12-161-0/+4
|/ | | | | | | | The .prepare callbacks are so far only called from msi_domain_alloc_irqs. In order to reuse that code, split that code and create a msi_domain_prepare_irqs function that the existing code can call into. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* Merge tag 'pci-v4.4-changes' of ↵Linus Torvalds2015-11-061-0/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "Resource management: - Add support for Enhanced Allocation devices (Sean O. Stalley) - Add Enhanced Allocation register entries (Sean O. Stalley) - Handle IORESOURCE_PCI_FIXED when sizing resources (David Daney) - Handle IORESOURCE_PCI_FIXED when assigning resources (David Daney) - Handle Enhanced Allocation capability for SR-IOV devices (David Daney) - Clear IORESOURCE_UNSET when reverting to firmware-assigned address (Bjorn Helgaas) - Make Enhanced Allocation bitmasks more obvious (Bjorn Helgaas) - Expand Enhanced Allocation BAR output (Bjorn Helgaas) - Add of_pci_check_probe_only to parse "linux,pci-probe-only" (Marc Zyngier) - Fix lookup of linux,pci-probe-only property (Marc Zyngier) - Add sparc mem64 resource parsing for root bus (Yinghai Lu) PCI device hotplug: - pciehp: Queue power work requests in dedicated function (Guenter Roeck) Driver binding: - Add builtin_pci_driver() to avoid registration boilerplate (Paul Gortmaker) Virtualization: - Set SR-IOV NumVFs to zero after enumeration (Alexander Duyck) - Remove redundant validation of SR-IOV offset/stride registers (Alexander Duyck) - Remove VFs in reverse order if virtfn_add() fails (Alexander Duyck) - Reorder pcibios_sriov_disable() (Alexander Duyck) - Wait 1 second between disabling VFs and clearing NumVFs (Alexander Duyck) - Fix sriov_enable() error path for pcibios_enable_sriov() failures (Alexander Duyck) - Enable SR-IOV ARI Capable Hierarchy before reading TotalVFs (Ben Shelton) - Don't try to restore VF BARs (Wei Yang) MSI: - Don't alloc pcibios-irq when MSI is enabled (Joerg Roedel) - Add msi_controller setup_irqs() method for special multivector setup (Lucas Stach) - Export all remapped MSIs to sysfs attributes (Romain Bezut) - Disable MSI on SiS 761 (Ondrej Zary) AER: - Clear error status registers during enumeration and restore (Taku Izumi) Generic host bridge driver: - Fix lookup of linux,pci-probe-only property (Marc Zyngier) - Allow multiple hosts with different map_bus() methods (David Daney) - Pass starting bus number to pci_scan_root_bus() (David Daney) - Fix address window calculation for non-zero starting bus (David Daney) Altera host bridge driver: - Add msi.h to ARM Kbuild (Ley Foon Tan) - Add Altera PCIe host controller driver (Ley Foon Tan) - Add Altera PCIe MSI driver (Ley Foon Tan) APM X-Gene host bridge driver: - Remove msi_controller assignment (Duc Dang) Broadcom iProc host bridge driver: - Fix header comment "Corporation" misspelling (Florian Fainelli) - Fix code comment to match code (Ray Jui) - Remove unused struct iproc_pcie.irqs[] (Ray Jui) - Call pci_fixup_irqs() for ARM64 as well as ARM (Ray Jui) - Fix PCIe reset logic (Ray Jui) - Improve link detection logic (Ray Jui) - Update PCIe device tree bindings (Ray Jui) - Add outbound mapping support (Ray Jui) Freescale i.MX6 host bridge driver: - Return real error code from imx6_add_pcie_port() (Fabio Estevam) - Add PCIE_PHY_RX_ASIC_OUT_VALID definition (Fabio Estevam) Freescale Layerscape host bridge driver: - Remove ls_pcie_establish_link() (Minghuan Lian) - Ignore PCIe controllers in Endpoint mode (Minghuan Lian) - Factor out SCFG related function (Minghuan Lian) - Update ls_add_pcie_port() (Minghuan Lian) - Remove unused fields from struct ls_pcie (Minghuan Lian) - Add support for LS1043a and LS2080a (Minghuan Lian) - Add ls_pcie_msi_host_init() (Minghuan Lian) HiSilicon host bridge driver: - Add HiSilicon SoC Hip05 PCIe driver (Zhou Wang) Marvell MVEBU host bridge driver: - Return zero for reserved or unimplemented config space (Russell King) - Use exact config access size; don't read/modify/write (Russell King) - Use of_get_available_child_count() (Russell King) - Use for_each_available_child_of_node() to walk child nodes (Russell King) - Report full node name when reporting a DT error (Russell King) - Use port->name rather than "PCIe%d.%d" (Russell King) - Move port parsing and resource claiming to separate function (Russell King) - Fix memory leaks and refcount leaks (Russell King) - Split port parsing and resource claiming from port setup (Russell King) - Use gpio_set_value_cansleep() (Russell King) - Use devm_kcalloc() to allocate an array (Russell King) - Use gpio_desc to carry around gpio (Russell King) - Improve clock/reset handling (Russell King) - Add PCI Express root complex capability block (Russell King) - Remove code restricting accesses to slot 0 (Russell King) NVIDIA Tegra host bridge driver: - Wrap static pgprot_t initializer with __pgprot() (Ard Biesheuvel) Renesas R-Car host bridge driver: - Build pci-rcar-gen2.c only on ARM (Geert Uytterhoeven) - Build pcie-rcar.c only on ARM (Geert Uytterhoeven) - Make PCI aware of the I/O resources (Phil Edworthy) - Remove dependency on ARM-specific struct hw_pci (Phil Edworthy) - Set root bus nr to that provided in DT (Phil Edworthy) - Fix I/O offset for multiple host bridges (Phil Edworthy) ST Microelectronics SPEAr13xx host bridge driver: - Fix dw_pcie_cfg_read/write() usage (Gabriele Paoloni) Synopsys DesignWare host bridge driver: - Make "clocks" and "clock-names" optional DT properties (Bhupesh Sharma) - Use exact access size in dw_pcie_cfg_read() (Gabriele Paoloni) - Simplify dw_pcie_cfg_read/write() interfaces (Gabriele Paoloni) - Require config accesses to be naturally aligned (Gabriele Paoloni) - Make "num-lanes" an optional DT property (Gabriele Paoloni) - Move calculation of bus addresses to DRA7xx (Gabriele Paoloni) - Replace ARM pci_sys_data->align_resource with global function pointer (Gabriele Paoloni) - Factor out MSI msg setup (Lucas Stach) - Implement multivector MSI IRQ setup (Lucas Stach) - Make get_msi_addr() return phys_addr_t, not u32 (Lucas Stach) - Set up high part of MSI target address (Lucas Stach) - Fix PORT_LOGIC_LINK_WIDTH_MASK (Zhou Wang) - Revert "PCI: designware: Program ATU with untranslated address" (Zhou Wang) - Use of_pci_get_host_bridge_resources() to parse DT (Zhou Wang) - Make driver arch-agnostic (Zhou Wang) Miscellaneous: - Make x86 pci_subsys_init() static (Alexander Kuleshov) - Turn off Request Attributes to avoid Chelsio T5 Completion erratum (Hariprasad Shenai)" * tag 'pci-v4.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits) PCI: altera: Add Altera PCIe MSI driver PCI: hisi: Add HiSilicon SoC Hip05 PCIe driver PCI: layerscape: Add ls_pcie_msi_host_init() PCI: layerscape: Add support for LS1043a and LS2080a PCI: layerscape: Remove unused fields from struct ls_pcie PCI: layerscape: Update ls_add_pcie_port() PCI: layerscape: Factor out SCFG related function PCI: layerscape: Ignore PCIe controllers in Endpoint mode PCI: layerscape: Remove ls_pcie_establish_link() PCI: designware: Make "clocks" and "clock-names" optional DT properties PCI: designware: Make driver arch-agnostic ARM/PCI: Replace pci_sys_data->align_resource with global function pointer PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT Revert "PCI: designware: Program ATU with untranslated address" PCI: designware: Move calculation of bus addresses to DRA7xx PCI: designware: Make "num-lanes" an optional DT property PCI: designware: Require config accesses to be naturally aligned PCI: designware: Simplify dw_pcie_cfg_read/write() interfaces PCI: designware: Use exact access size in dw_pcie_cfg_read() PCI: spear: Fix dw_pcie_cfg_read/write() usage ...
| * PCI: Add msi_controller setup_irqs() method for special multivector setupLucas Stach2015-09-181-0/+2
| | | | | | | | | | | | | | | | | | | | Add a msi_controller setup_irqs() method so MSI chip providers can implement their own multivector MSI setup. [bhelgaas: changelog] Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pratyush Anand <pratyush.anand@gmail.com>
* | PCI/MSI: Allow the MSI domain to be device-specificMarc Zyngier2015-10-161-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So far, we've always considered that for a given PCI device, its MSI controller was either set by the architecture-specific pcibios hook, or simply inherited from the host bridge. This doesn't cover things like firmware-defined topologies like msi-map (DT) or IORT (ACPI), which can provide information about which MSI controller to use on a per-device basis. This patch adds the necessary hook into the MSI code to allow this feature, and provides the msi-map functionnality as a first implementation. Acked-by: Rob Herring <robh@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* | PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().David Daney2015-10-161-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add pci_msi_domain_get_msi_rid() to return the MSI requester id (RID). Initially needed by gic-v3 based systems. It will be used by follow on patch to drivers/irqchip/irq-gic-v3-its-pci-msi.c Initially supports mapping the RID via OF device tree. In the future, this could be extended to use ACPI _IORT tables as well. Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* | irqdomain/msi: Use fwnode instead of of_nodeMarc Zyngier2015-10-131-4/+5
|/ | | | | | | | | | | | | | | | | | | | | | | As we continue to push of_node towards the outskirts of irq domains, let's start tackling the case of msi_create_irq_domain and its little friends. This has limited impact in both PCI/MSI, platform MSI, and a few drivers. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Tested-by: Hanjun Guo <hanjun.guo@linaro.org> Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: <linux-arm-kernel@lists.infradead.org> Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org> Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> Cc: Graeme Gregory <graeme@xora.org.uk> Cc: Jake Oshins <jakeo@microsoft.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Link: http://lkml.kernel.org/r/1444737105-31573-17-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* PCI/MSI: Drop domain field from msi_controllerMarc Zyngier2015-07-301-3/+0
| | | | | | | | | | | | | | | | | | The only three users of that field are not using the msi_controller structure anymore, so drop it altogether. Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: <linux-arm-kernel@lists.infradead.org> Cc: Yijing Wang <wangyijing@huawei.com> Cc: Ma Jun <majun258@huawei.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Duc Dang <dhdang@apm.com> Cc: Hanjun Guo <hanjun.guo@linaro.org> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1438091186-10244-20-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* drivers/base: Add MSI domain support for non-PCI devicesMarc Zyngier2015-07-301-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With the msi_list and the msi_domain properties now being at the generic device level, it is starting to be relatively easy to offer a generic way of providing non-PCI MSIs. The two major hurdles with this idea are: - Lack of global ID that identifies a device: this is worked around by having a global ID allocator for each device that gets enrolled in the platform MSI subsystem - Lack of standard way to write the message in the generating device. This is solved by mandating driver code to provide a write_msg callback, so that everyone can have their own square wheel Apart from that, the API is fairly straightforward: - platform_msi_create_irq_domain creates an MSI domain that gets tagged with DOMAIN_BUS_PLATFORM_MSI - platform_msi_domain_alloc_irqs allocate MSIs for a given device, populating the msi_list - platform_msi_domain_free_irqs does what is written on the tin [ tglx: Created a seperate struct platform_msi_desc and added kerneldoc entries ] Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: <linux-arm-kernel@lists.infradead.org> Cc: Yijing Wang <wangyijing@huawei.com> Cc: Ma Jun <majun258@huawei.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Duc Dang <dhdang@apm.com> Cc: Hanjun Guo <hanjun.guo@linaro.org> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1438091186-10244-10-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* genirq/MSI: Move alloc_msi_entry() from PCI into generic MSI codeJiang Liu2015-07-221-0/+2
| | | | | | | | | | | | | | | | | | | Move alloc_msi_entry() from PCI MSI code into generic MSI code, so it can be reused by other generic MSI drivers. Also introduce free_msi_entry() for completeness. Suggested-by: Stuart Yoder <stuart.yoder@freescale.com>. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Yijing Wang <wangyijing@huawei.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Grant Likely <grant.likely@linaro.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Alexander Gordeev <agordeev@redhat.com> Link: http://lkml.kernel.org/r/1436428847-8886-13-git-send-email-jiang.liu@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* genirq/MSI: Reorginize struct msi_desc to prepare for support of generic MSIJiang Liu2015-07-221-20/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reorganize struct msi_desc so it could be reused by other MSI drivers. We have the following layout now: struct msi_desc { /* Shared device/bus independent data */ ... union { /* PCI specific data */ struct { ... }; }; }; We need to have anonymous union and a anonymous structure for the PCI fields, otherwise we would have to change all instances using these fields. For non PCI devices we will enforce a proper namespace and a non anonymous structure. [ tglx: Added proper comments to the structure and massaged changelog ] Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Reviewed-by: Yijing Wang <wangyijing@huawei.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Stuart Yoder <stuart.yoder@freescale.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Alexander Gordeev <agordeev@redhat.com> Link: http://lkml.kernel.org/r/1436428847-8886-12-git-send-email-jiang.liu@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* genirq/MSI: Store 'struct device' instead of 'struct pci_dev' in struct msi_descJiang Liu2015-07-221-7/+4
| | | | | | | | | | | | | | | | | | Store 'struct device *' instead of 'struct pci_dev *' in struct msi_desc, so struct msi_desc can be reused by non PCI based MSI drivers. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Reviewed-by: Yijing Wang <wangyijing@huawei.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Stuart Yoder <stuart.yoder@freescale.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Alexander Gordeev <agordeev@redhat.com> Link: http://lkml.kernel.org/r/1436428847-8886-11-git-send-email-jiang.liu@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* genirq/MSI: Move msi_list from struct pci_dev to struct deviceJiang Liu2015-07-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move msi_list from struct pci_dev into struct device, so we can support non-PCI-device based generic MSI interrupts. msi_list is now conditional under CONFIG_GENERIC_MSI_IRQ, which is selected from CONFIG_PCI_MSI, so no functional change for PCI MSI users. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Reviewed-by: Yijing Wang <wangyijing@huawei.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Stuart Yoder <stuart.yoder@freescale.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Joe Perches <joe@perches.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Joerg Roedel <jroedel@suse.de> Cc: Alexander Gordeev <agordeev@redhat.com> Link: http://lkml.kernel.org/r/1436428847-8886-10-git-send-email-jiang.liu@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* PCI: Add helper function msi_desc_to_pci_sysdata()Jiang Liu2015-07-221-0/+7
| | | | | | | | | | | | | | | | | | | | Add helper function msi_desc_to_pci_sysdata() to retrieve sysdata from an MSI descriptor. To avoid pulling include/linux/pci.h into include/linux/msi.h, msi_desc_to_pci_sysdata() is implemented as a normal function instead of an inline function. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Reviewed-by: Yijing Wang <wangyijing@huawei.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Stuart Yoder <stuart.yoder@freescale.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Alexander Gordeev <agordeev@redhat.com> Link: http://lkml.kernel.org/r/1436428847-8886-2-git-send-email-jiang.liu@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* PCI/MSI: Allow an msi_controller to be associated to an irq domainMarc Zyngier2014-11-231-0/+3
| | | | | | | | | | | | | | | | | | | | | With the new stacked irq domains, it becomes pretty tempting to allocate an MSI domain per PCI bus, which would remove the requirement of either relying on arch-specific code, or a default PCI MSI domain. By allowing the msi_controller structure to carry a pointer to an irq_domain, we can easily use this in pci_msi_setup_msi_irqs. The existing code can still be used as a fallback if the MSI driver does not populate the domain field. Tested on arm64 with the GICv3 ITS driver. Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Jiang Liu <jiang.liu@linux.intel.com> Link: http://lkml.kernel.org/r/1416048553-29289-2-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* PCI/MSI: Provide mechanism to alloc/free MSI/MSIX interrupt from irqdomainJiang Liu2014-11-231-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | Provide mechanism to directly alloc/free MSI/MSIX interrupt from irqdomain, which will be used to replace arch_setup_msi_irq()/ arch_setup_msi_irqs()/arch_teardown_msi_irq()/arch_teardown_msi_irqs(). To kill weak functions, this patch introduce a new weak function arch_get_pci_msi_domain(), which is to retrieve the MSI irqdomain for a PCI device. This weak function could be killed once we get a common way to associate MSI domain with PCI device. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Yijing Wang <wangyijing@huawei.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Alexander Gordeev <agordeev@redhat.com> Link: http://lkml.kernel.org/r/1416061447-9472-10-git-send-email-jiang.liu@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* PCI/MSI: Enhance core to support hierarchy irqdomainJiang Liu2014-11-231-0/+14
| | | | | | | | | | | | | | | Enhance PCI MSI core to support hierarchy irqdomain, so the common code can be shared across architectures. [ tglx: Extracted and combined from several patches ] Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* genirq: Provide default callbacks for msi_domain_opsJiang Liu2014-11-231-5/+37
| | | | | | | | | | | | | | | | | | | Extend struct msi_domain_info and provide default callbacks for msi_domain_ops. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Yijing Wang <wangyijing@huawei.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Alexander Gordeev <agordeev@redhat.com> Link: http://lkml.kernel.org/r/1416061447-9472-8-git-send-email-jiang.liu@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* genirq: Introduce msi_domain_alloc/free_irqs()Jiang Liu2014-11-231-0/+29
| | | | | | | | | | | | | | | | | | | Introduce msi_domain_{alloc|free}_irqs() to alloc/free interrupts from generic MSI irqdomain. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Yijing Wang <wangyijing@huawei.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Alexander Gordeev <agordeev@redhat.com> Link: http://lkml.kernel.org/r/1416061447-9472-7-git-send-email-jiang.liu@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* genirq: Add generic msi irq domain supportJiang Liu2014-11-231-0/+45
| | | | | | | | | | | | | | | Implement the basic functions for MSI interrupt support with hierarchical interrupt domains. [ tglx: Extracted and combined from several patches ] Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* PCI/MSI: Introduce helpers to hide struct msi_desc implementation detailsJiang Liu2014-11-231-0/+19
| | | | | | | | | | | | | | | | | | | | Introduce helpers to hide struct msi_desc implementation details, so we could easily support non-PCI-compliant MSI devices later by moving msi_list into struct device. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Yijing Wang <wangyijing@huawei.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Alexander Gordeev <agordeev@redhat.com> Link: http://lkml.kernel.org/r/1416061447-9472-6-git-send-email-jiang.liu@linux.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* PCI/MSI: Rename mask/unmask_msi_irq et alThomas Gleixner2014-11-231-5/+13
| | | | | | | | | | | | | | | | | | | | | mask/unmask_msi_irq and __mask_msi/msix_irq are PCI/MSI specific functions and should be named accordingly. This is a preparatory patch to support MSI on non PCI devices. Rename mask/unmask_msi_irq to pci_msi_mask/unmask_irq and document the functions. Provide conversion helpers. Rename __mask_msi/msix_irq to __pci_msi/msix_desc_mask so its clear that they operated on msi_desc. Fixup the only user outside of pci/msi. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Yijing Wang <wangyijing@huawei.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
* PCI/MSI: Rename write_msi_msg() to pci_write_msi_msg()Jiang Liu2014-11-231-2/+12
| | | | | | | | | | | | | Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI specific. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* PCI/MSI: Rename __read_msi_msg() to __pci_read_msi_msg()Jiang Liu2014-11-231-2/+3
| | | | | | | | | | | | | | Rename __read_msi_msg() to __pci_read_msi_msg() and kill unused read_msi_msg(). It's a preparation to separate generic MSI code from PCI core. Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Grant Likely <grant.likely@linaro.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* PCI/MSI: Rename "struct msi_chip" to "struct msi_controller"Yijing Wang2014-11-121-3/+3
| | | | | | | | | | | | "msi_chip" isn't very descriptive, so rename it to "msi_controller". That tells a little more about what it does and is already used in device tree bindings. No functional change. [bhelgaas: changelog, change *only* the struct name so it's reviewable] Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* s390/MSI: Use __msi_mask_irq() instead of default_msi_mask_irq()Yijing Wang2014-11-111-2/+0
| | | | | | | | | | | Now only s390/MSI use default_msi_mask_irq() and default_msix_mask_irq(), replace them with the common MSI mask IRQ functions __msi_mask_irq() and __msix_mask_irq(). Remove default_msi_mask_irq() and default_msix_mask_irq(). Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com> CC: linux-s390@vger.kernel.org
* Revert "PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()"Yijing Wang2014-11-111-2/+4
| | | | | | | | | | | | | | | | | | | The problem fixed by 0e4ccb1505a9 ("PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()") has been fixed in a simpler way by a previous commit ("PCI/MSI: Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask Bits"). The msi_mask_irq() and msix_mask_irq() x86_msi_ops added by 0e4ccb1505a9 are no longer needed, so revert the commit. default_msi_mask_irq() and default_msix_mask_irq() were added by 0e4ccb1505a9 and are still used by s390, so keep them for now. [bhelgaas: changelog] Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: David Vrabel <david.vrabel@citrix.com> CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> CC: xen-devel@lists.xenproject.org
* PCI/MSI: Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask BitsYijing Wang2014-11-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | MSI-X vector Mask Bits are in MSI-X Tables in PCI memory space. Xen PV guests can't write to those tables. MSI vector Mask Bits are in PCI configuration space. Xen PV guests can write to config space, but those writes are ignored. Commit 0e4ccb1505a9 ("PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()") added a way to override default_mask_msi_irqs() and default_mask_msix_irqs() so they can be no-ops in Xen guests, but this is more complicated than necessary. Add "pci_msi_ignore_mask" in the core PCI MSI code. If set, default_mask_msi_irqs() and default_mask_msix_irqs() return without doing anything. This is less flexible, but much simpler. [bhelgaas: changelog] Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> CC: xen-devel@lists.xenproject.org
* PCI/MSI: Remove "pos" from the struct msi_desc msi_attribYijing Wang2014-10-011-1/+0
| | | | | | | | | | "msi_attrib.pos" is only used for MSI (not MSI-X), and we already cache the MSI capability offset in "dev->msi_cap". Remove "pos" from the struct msi_attrib and use "dev->msi_cap" directly. [bhelgaas: changelog, fix whitespace] Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* PCI/MSI: Remove unused kobject from struct msi_descYijing Wang2014-10-011-2/+0
| | | | | | | | | | | | After commit 1c51b50c2995 ("PCI/MSI: Export MSI mode using attributes, not kobjects"), the kobject in struct msi_desc is unused. Remove the unused struct kobject from struct msi_desc. [bhelgaas: changelog] Fixes: 1c51b50c2995 ("PCI/MSI: Export MSI mode using attributes, not kobjects") Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* PCI/MSI: Remove arch_msi_check_device()Alexander Gordeev2014-10-011-3/+0
| | | | | | | | | | | No architectures implement arch_msi_check_device() or the struct msi_chip .check_device() method, so remove them. Remove the "type" parameter to pci_msi_check_device() because it was only used to call arch_msi_check_device() and is no longer needed. [bhelgaas: changelog, split to separate patch] Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* PCI/MSI: Cache Multiple Message Capable in struct msi_descYijing Wang2014-07-031-1/+2
| | | | | | | | | | | | | The Multiple Message Capable field in the MSI Message Control register indicates how many vectors the device supports. This field is read-only, so cache it in msi_desc to avoid reading it repeatedly. Since we cache the extracted field (not the entire Message Control register), we can use msi_mask() instead of msi_capable_mask(), which is then unused, so remove it. [bhelgaas: fix whitespace, changelog] Signed-off-by: Yijing Wang <wangyijing@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* PCI: Drop "irq" param from *_restore_msi_irqs()DuanZhenzhong2013-12-131-2/+2
| | | | | | | | | | | | | | | Change x86_msi.restore_msi_irqs(struct pci_dev *dev, int irq) to x86_msi.restore_msi_irqs(struct pci_dev *dev). restore_msi_irqs() restores multiple MSI-X IRQs, so param 'int irq' is unneeded. This makes code more consistent between vm and bare metal. Dom0 MSI-X restore code can also be optimized as XEN only has a hypercall to restore all MSI-X vectors at one time. Tested-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
OpenPOWER on IntegriCloud