| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer updates from Dmitry Torokhov:
- a bunch of new drivers (DA9052/53 touchscreenn controller, Synaptics
Navpoint, LM8333 keypads, Wacom I2C touhscreen);
- updates to existing touchpad drivers (ALPS, Sntelic);
- Wacom driver now supports Intuos5;
- device-tree bindings in numerous drivers;
- other cleanups and fixes.
Fix annoying conflict in drivers/input/tablet/wacom_wac.c that I think
implies that the input layer device naming is broken, but let's see. I
brough it up with Dmitry.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: matrix-keymap - fix building keymaps
Input: spear-keyboard - document DT bindings
Input: spear-keyboard - add device tree bindings
Input: matrix-keymap - wire up device tree support
Input: matrix-keymap - uninline and prepare for device tree support
Input: adp5588 - add support for gpio names
Input: omap-keypad - dynamically handle register offsets
Input: synaptics - fix compile warning
MAINTAINERS: adjust input-related patterns
Input: ALPS - switch to using input_mt_report_finger_count
Input: ALPS - add semi-MT support for v4 protocol
Input: Add Synaptics NavPoint (PXA27x SSP/SPI) driver
Input: atmel_mxt_ts - dump each message on just 1 line
Input: atmel_mxt_ts - do not read extra (checksum) byte
Input: atmel_mxt_ts - verify object size in mxt_write_object
Input: atmel_mxt_ts - only allow root to update firmware
Input: atmel_mxt_ts - use CONFIG_PM_SLEEP
Input: sentelic - report device's production serial number
Input: tl6040-vibra - Device Tree support
Input: evdev - properly handle read/write with count 0
...
|
| | |
| |
| |
| |
| |
| | |
Signed-off-by: Jean-François Dagenais <jeff.dagenais@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| |\ \
| |/
|/|
| |
| | |
Conflicts:
drivers/regulator/88pm8607.c (simple overlap with a bugfix in v3.4)
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The regulators in the twl4030 can provide some voltage settings
that are not offically supported.
These settings are disabled by default, but can be enabled with
CONFIG_TWL4030_ALLOW_UNSUPPORTED=y
However
- that config variable is not mentioned in any Kconfig so cannot
be used, and
- a global setting is clumsy - a per regulator setting would be
better.
So define a new 'feature' flag that a board file can set to enable
these unsupported volatages for boards which need them.
This flag cannot (yet) be set using device-tree.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
twl-regulator has a collection of feature flags, some defined
in twl-core.c and one defined in i2c/twl.h.
This is confusing for anyone adding a new feature flag.
So collect them together and place them in twl.h immediately
after the structure in which they are initially set.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
| |
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
- 4 new drivers: Freescale i.MX on-chip Anatop, Ricoh's RC5T583 and
TI's TPS65090 and TPS65217.
- New variants support (8420, 8520 ab9540), cleanups and bug fixes for
the abx500 and db8500 ST-E chipsets.
- Some minor fixes and update for the wm8994 from Mark.
- The beginning of a long term TWL cleanup effort coming from the TI
folks.
- Various fixes and cleanups for the s5m, TPS659xx, pm860x, and MAX8997
drivers.
Fix up trivial conflicts due to duplicate patches and header file
cleanups (<linux/device.h> removal etc).
* tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (97 commits)
gpio/twl: Add DT support to gpio-twl4030 driver
gpio/twl: Allocate irq_desc dynamically for SPARSE_IRQ support
mfd: Detach twl6040 from the pmic mfd driver
mfd: Replace twl-* pr_ macros by the dev_ equivalent and do various cleanups
mfd: Micro-optimization on twl4030 IRQ handler
mfd: Make twl4030 SIH SPARSE_IRQ capable
mfd: Move twl-core IRQ allocation into twl[4030|6030]-irq files
mfd: Remove references already defineid in header file from twl-core
mfd: Remove unneeded header from twl-core
mfd: Make twl-core not depend on pdata->irq_base/end
ARM: OMAP2+: board-omap4-*: Do not use anymore TWL6030_IRQ_BASE in board files
mfd: Return twl6030_mmc_card_detect IRQ for board setup
Revert "mfd: Add platform data for MAX8997 haptic driver"
mfd: Add support for TPS65090
mfd: Add some da9052-i2c section annotations
mfd: Build rtc5t583 only if I2C config is selected to y.
mfd: Add anatop mfd driver
mfd: Fix compilation error in tps65910.h
mfd: Add 8420 variant to db8500-prcmu
mfd: Add 8520 PRCMU variant to db8500-prcmu
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
twl4030 is using a two level irq controllers infrastruture.
So far, only the first level was using dynamic irq_desc allocation
to be able to have irq_domain support for device tree.
There is a need to allocate separate irq_descs for the SIH too to
avoid hacking the first level with interrupts from the second level.
Add an irq_base parameter to allow the caller to provide the base from
pdata or from dynamic allocation.
Affect TWL4030_NR_IRQS to the twl-core IRQs only.
Moreover that will allow the extraction of the of_node pointer for further
Device Tree conversion.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull i2c embedded updates from Wolfram Sang:
"Nothing special from i2c-embedded for this merge window. Two new
drivers, minor feature additions, bugfixes, cleanups.
All patches have been in linux-next for some time, too."
* 'i2c-embedded/for-3.4' of git://git.pengutronix.de/git/wsa/linux:
i2c-eg20t: Remove write-only variables
i2c-eg20t: Rework pch_i2c_wait_for_bus_idle to reduce wait time
i2c-s3c2410: Add stub runtime power management
i2c-s3c2410: Convert to devm_kzalloc()
i2c: add CSR SiRFprimaII on-chip I2C controllers driver
i2c: tegra: Remove unnecessary write to INT_STATUS
i2c: imx: fix imx driver to work though signal is pending
i2c: designware: dw_i2c_init_driver as subsys initcall
misc: at24: describe platform_data with kernel_doc
i2c: Move I2C_EG20T option to the right place.
i2c: Support for Netlogic XLR/XLS I2C controller.
i2c: mpc: Add support for SMBUS_READ_BLOCK_DATA
i2c: versatile: Add Device Tree support
|
| | |/
| |
| |
| |
| |
| |
| | |
There have been questions about its fields lately, so describe them properly.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull drm main changes from Dave Airlie:
"This is the main drm pull request, I'm probably going to send two more
smaller ones, will explain below.
This contains a patch that is also in the fbdev tree, but it should be
the same patch, it added an API for hot unplugging framebuffer
devices, and I need that API for a new driver.
It also contains some changes to the i2c tree which Jean has acked,
and one change to moorestown platform stuff in x86.
Highlights:
- new drivers: UDL driver for USB displaylink devices, kms only,
should support correct hotplug operations.
- core: i2c speedups + better hotplug support, EDID overriding via
firmware interface - allows user to load a firmware for a broken
monitor/kvm from userspace, it even has documentation for it.
- exynos: new HDMI audio + hdmi 1.4 + virtual output driver
- gma500: code cleanup
- radeon: cleanups, CS optimisations, streamout support and pageflip
fix
- nouveau: NVD9 displayport support + more reclocking work
- i915: re-enabling GMBUS, finish gpu patch (might help hibernation
who knows), missed irq fixes, stencil tiling fixes, interlaced
support, aliasesd PPGTT support for SNB/IVB, swizzling for SNB/IVB,
semaphore fixes
As well as the usual bunch of cleanups and fixes all over the place.
I've got two things I'd like to merge a bit later:
a) AMD support for all their new radeonhd 7000 series GPU and APUs.
AMD dropped this a bit late due to insane internal review
processes, (please AMD just follow Intel and let open source guys
ship stuff early) however I don't want to penalise people who own
this hardware (since its been on sale for 3-4 months and GPU hw
doesn't exactly have a lifetime in years) and consign them to
using closed drivers for longer than necessary. The changes are
well contained and just plug into the driver new gpu functionality
so they should be fairly regression proof. I just want to give
them a bit of a run on the hw AMD kindly sent me.
b) drm prime/dma-buf interface code. This is just infrastructure
code to expose the dma-buf stuff to drm drivers and to userspace.
I'm not planning on pushing any driver support in this cycle
(except maybe exynos), but I'd like to get the infrastructure code
in so for the next cycle I can start getting the driver support
into the individual drivers. We have started driver support for
i915, nouveau and udl along with I think exynos and omap in
staging. However this code relies on the dma-buf tree being
pulled into your tree first since it needs the latest interfaces
from that tree. I'll push to get that tree sent asap.
(oh and any warnings you see in i915 are gcc's fault from what anyone
can see)."
Fix up trivial conflicts in arch/x86/platform/mrst/mrst.c due to the new
msic_thermal_platform_data() thermal function being added next to the
tc35876x_platform_data() i2c device function..
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (326 commits)
drm/i915: use DDC_ADDR instead of hard-coding it
drm/radeon: use DDC_ADDR instead of hard-coding it
drm: remove unneeded redefinition of DDC_ADDR
drm/exynos: added virtual display driver.
drm: allow loading an EDID as firmware to override broken monitor
drm/exynos: enable hdmi audio feature
drm/exynos: add default pixel format for plane
drm/exynos: cleanup exynos_hdmi.h
drm/exynos: add is_local member in exynos_drm_subdrv struct
drm/exynos: add subdrv open/close functions
drm/exynos: remove module of exynos drm subdrv
drm/exynos: release pending pageflip events when closed
drm/exynos: added new funtion to get/put dma address.
drm/exynos: update gem and buffer framework.
drm/exynos: added mode_fixup feature and code clean.
drm/exynos: add HDMI version 1.4 support
drm/exynos: remove exynos_mixer.h
gma500: Fix mmap frambuffer
drm/radeon: Drop radeon_gem_object_(un)pin.
drm/radeon: Restrict offset for legacy display engine.
...
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We need to merge this ahead of some of the cleanup because a lot of needed
cleanup spans both new and old chips. If we try and clean up and the merge
we end up fighting ourselves.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[With a load of the cleanup stuff folded in, register stuff reworked sanely]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
To be able to attach consumers to these supplies from board
files we need to have regulator_init_data for them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
vdd1 and vdd2 are now common regulators for twl4030 and twl6030. Also
added vdd3 as a new regulator for twl6030. twl6030 vdd1...vdd3 smps
regulator voltages can only be controlled through the smartreflex
voltage channel, thus the support for the voltage_get and set is
minimal and requires external controller.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
| |
This is needed for SMPS regulators, which use the OMAP voltage
processor for voltage get/set functions instead of the normal I2C
channel. For this purpose, regulator_init_data->driver_data contents
are expanded, it is now a struct which contains function pointers
for the set/get voltage operations, a data pointer for these, and
the previously used features bitmask.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com> [for the MFD part]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
TWL family of PMICs, used in master mode, have a power off
functionality. The resulting power off sequence shuts down all the SoC
supplies, LDOs, etc. The sequence is described in the datasheets
chapter "Power-Off Sequence".
Note, that board must be wired correctly for the power off to work as
expected.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Without turning the MADC clock on, no MADC conversions occur.
$ cat /sys/class/hwmon/hwmon0/device/in8_input
[ 53.428436] twl4030_madc twl4030_madc: conversion timeout!
cat: read error: Resource temporarily unavailable
Signed-off-by: Kyle Manna <kyle@kylemanna.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |/
|
|
|
|
|
|
|
| |
Abort driver initialization if X plate resistance was not specified in
platform data as it will cause pressure to be always calculated as 0,
and making userspace ignore touch coordinates.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| |\ \
| | |
| | |
| | | |
git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc into next/devel-2
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Enable ramp down/up step to be configured based on
platform.
Signed-off-by: Axel Castaneda Gonzalez <x0055901@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add twl6040_vibra as a child of MFD device twl6040_codec. This
implementation covers the PCM-to-PWM mode of TWL6040 vibrator
module.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Tejun Heo <tj@kernel.org>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
TWL6040 IC provides analog high-end audio codec functions for
handset applications. It contains several audio analog inputs
and outputs as well as vibrator support. It's connected to the
host processor via PDM interface for audio data communication.
The audio modules are controlled by internal registers that
can be accessed by I2C and PDM interface.
TWL6040 MFD will be registered as a child of TWL-CORE, and will
have two children of its own: twl6040-codec and twl6040-vibra.
This driver is based on TWL4030 and WM8350 MFD drivers.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Allign the platform data names for twl4030 audio submodule:
twl4030_audio_data: for the core MFD driver
twl4030_codec_data: for ASoC codec driver
twl4030_vibra_data: for the input/ForceFeedback driver
To avoid breakage, change all depending drivers, files
to use the new types.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |/
|
|
|
|
|
|
| |
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
| |
The charger fault IRQs from the twl will in future patches be handled
by a seperate IRQ handler in the charger driver than the general charger
IRQ. Give them different IRQ numbers now to allow the charger driver to
be merged in the future.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Phoenix Lite is based on the twl6030 family of PMICs. It has mostly the
same feature set of twl6030 but with small changes. The codec block has
also been removed. It also has a new charger block and new features in
its ADC block. VUSB handling also differs.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
| |
Added API to get the TWL5030 Si version from the IDCODE register.
It is used for enabling the workaround for TWL erratum 27.
Signed-off-by: Lesly A M <leslyam@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Modifying the macro name Main_Ref to all caps(MAIN_REF).
Suggested by Nishanth Menon <nm@ti.com>
Signed-off-by: Lesly A M <leslyam@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* 'for-linus/2640/i2c' of git://git.fluff.org/bjdooks/linux: (21 commits)
mach-ux500: set proper I2C platform data from MOP500s
i2c-nomadik: break out single messsage transmission
i2c-nomadik: reset the hw after status check
i2c-nomadik: remove the unnecessary delay
i2c-nomadik: change the TX and RX threshold
i2c-nomadik: add code to retry on timeout failure
i2c-nomadik: use pm_runtime API
i2c-nomadik: print abort cause only on abort tag
i2c-nomadik: correct adapter timeout initialization
i2c-nomadik: remove the redundant error message
i2c-nomadik: corrrect returned error numbers
i2c-nomadik: fix speed enumerator
i2c-nomadik: make i2c timeout specific per i2c bus
i2c-nomadik: add regulator support
i2c: i2c-sh_mobile bus speed platform data V2
i2c: i2c-sh_mobile clock string removal
i2c-eg20t: Support new device ML7223 IOH
i2c: tegra: Add de-bounce cycles.
i2c: tegra: fix repeated start handling
i2c: tegra: recover from spurious interrupt storm
...
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Add support to the i2c-sh_mobile driver for setting
the I2C bus speed using platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
These new platform-specific values can be used to set the fuzz parameter
passed to the input_set_abs_params() function for the ABS_X, ABS_Y and
ABS_PRESSURE axes.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
This new parameter allows the polling frequency to be configured while
keeping the default of once every millisecond.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Depending on the quality of the touch panel, the time for the X-, X+, Y-
and Y+ inputs to settle may vary. The poll_delay parameter can be used
to override the default of 1 millisecond.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Finger touch events or very quick stylus events on low-quality panels
can cause the tsc2007 to read bogus values. Looking at oscilloscope
snapshots, this seems to be caused by the touch event disappearing
during the measurements. These bogus values result in misclicks, where
the X and Y values deviate from the real position.
Most of these misclicks can be filtered out by setting a low enough
threshold for the maximum resistance (which is loosely the inverse of
the pressure) allowed to consider a set of values valid. Since this
behaviour is largely dependent on the type and quality of the panel,
this commit introduces the max_rt parameter. The default value is kept
at MAX_12BIT.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| |/
|
|
|
|
|
|
|
|
|
| |
This patch adds basic support for Freescale MPR121 capacitive touch
sensor. It's an i2c controller with up to 12 capacitance sensing inputs.
Product information (data sheet, application notes) can be found here:
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPR121
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| |
|
|
|
|
|
|
|
| |
Introducing a driver for MADC on TWL4030 powerIC. MADC stands for monitoring
ADC. This driver monitors the real time conversion of analog signals like
battery temperature, battery cuurent etc.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
In OMAP4 Blaze and Panda, 32KHz clock to WLAN is supplied from Phoenix
TWL6030. The 32KHz clock state (ON/OFF) is configured in
CLK32KG_CFG_[GRP, TRANS, STATE] register. This follows the same register
programming model as other regulators in TWL6030. So add CLK32KG as pseudo
regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* 'for-linus/2639/i2c-2' of git://git.fluff.org/bjdooks/linux:
i2c-pxa2xx: Don't clear isr bits too early
i2c-pxa2xx: Fix register offsets
i2c-pxa2xx: pass of_node from platform driver to adapter and publish
i2c-pxa2xx: check timeout correctly
i2c-pxa2xx: add support for shared IRQ handler
i2c-pxa2xx: Add PCI support for PXA I2C controller
ARM: pxa2xx: reorganize I2C files
i2c-pxa2xx: use dynamic register layout
i2c-mxs: set controller to pio queue mode after reset
i2c-eg20t: support new device OKI SEMICONDUCTOR ML7213 IOH
i2c/busses: Add support for Diolan U2C-12 USB-I2C adapter
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch moves the platform data definition from
arch/arm/plat-pxa/include/plat/i2c.h to include/linux/i2c/pxa-i2c.h so
it can be accessed from x86 the same way as on ARM.
This change should make no functional change to the PXA code. The move
is verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig mmp2_defconfig pxa168_defconfig
pxa910_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Configuration for ads1015 gain and datarate is possible via
devicetree or platform data.
This is a followup patch to previous ads1015 patches on Jean Delvares
tree.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
| |/
|
|
|
| |
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tsc2005 - remove 'disable' sysfs attribute
Input: tsc2005 - add open/close
Input: tsc2005 - handle read errors from SPI layer
Input: tsc2005 - do not rearm timer in hardirq handler
Input: tsc2005 - don't use work for 'pen up' handling
Input: tsc2005 - do not use 0 in place of NULL
Input: tsc2005 - use true/false for boolean variables
Input: tsc2005 - hide selftest attribute if we can't reset
Input: tsc2005 - rework driver initialization code
Input: tsc2005 - set up bus type in input device
Input: tsc2005 - set up parent device
Input: tsc2005 - clear driver data after unbinding
Input: tsc2005 - add module description
Input: tsc2005 - remove driver banner message
Input: tsc2005 - remove incorrect module alias
Input: tsc2005 - convert to using dev_pm_ops
Input: tsc2005 - use spi_get/set_drvdata()
Input: introduce tsc2005 driver
Input: xen-kbdfront - move to drivers/input/misc
Input: xen-kbdfront - add grant reference for shared page
...
|
| | |
| |
| |
| |
| |
| |
| |
| | |
This adds support for system-level suspend/resume to the driver.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Different board have different requirements/setups so let's be more
flexible.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
As there is no common configuration settings that would work in every
situation, remove the fixed config data from driver code and add
config data to platform data.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Change prefixes from qt602240 to mxt to reflect that the driver supports
whole line of mXT touchscreens.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Since the driver will be supporting whole range of Atmels mXT touchscreen
controllers we better rename it to atmel_mxt_ts.
Acked-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
audio_mclk can be queried from mfd driver. Therefore, it is not
needed in twl4030_codec_audio_data or in twl4030_codec_vibra_data
anymore.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
